diff --git a/.github/workflows/test-builds.yml b/.github/workflows/test-builds.yml index 069f36714d..e339f85646 100644 --- a/.github/workflows/test-builds.yml +++ b/.github/workflows/test-builds.yml @@ -76,6 +76,7 @@ jobs: - STM32F103RE_btt - STM32F103RE_btt_USB - STM32F103RE_creality + - STM32F401RC_creality - STM32F103VE_longer - STM32F407VE_black - STM32F401VE_STEVAL diff --git a/Ender3V2S1_Dwin_TM3DV2.7z b/Ender3V2S1_Dwin_TM3DV2.7z new file mode 100644 index 0000000000..25331bc034 Binary files /dev/null and b/Ender3V2S1_Dwin_TM3DV2.7z differ diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index 88c9eb2fe3..aea4ad4473 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -55,6 +55,7 @@ //#define MachineEnder2Pro //#define MachineEnder3V2 //#define MachineEnder3S1 +//#define MachineEnder3S1_F4 //#define MachineEnder3Max //#define MachineEnder3Pro422 //#define MachineEnder3Pro427 @@ -85,7 +86,7 @@ // Enable this if you used a plug and play creality e3d or mosquito kit and kept the Creality thermistor //#define CrealityThermistor -//#define SlicePT1000 // Enable this if you have a mosquito with the newer PT1000 sensor +#define SlicePT1000 // Enable this if you have a mosquito with the newer PT1000 sensor //#define PID50W //Set PID for 50W Heater /* * Select these if you have changed to a high performance extruder @@ -441,6 +442,11 @@ #endif #endif +#if ENABLED(MachineEnder3S1_F4) + #define MachineEnder3S1 +#endif + + #if ENABLED(MachineEnder3S1) #if NONE(ABL_NCSW, ABL_EZABL, ABL_BLTOUCH) #define ABL_BLTOUCH @@ -450,7 +456,7 @@ #endif #endif -#if ENABLED(MachineEnder3S1) +#if ANY(MachineEnder3S1, MachineCR10SmartPro) #define SpriteExtruder #endif @@ -691,11 +697,11 @@ #define LCD_SERIAL_PORT 3 #define LCD_BAUDRATE 115200 #define SERIAL_CATCHALL 1 -#elif ANY(MachineCR10Smart, MachineCR10SmartPro) +#elif ENABLED(MachineCR10Smart) #define LCD_SERIAL_PORT 3 #define LCD_BAUDRATE 115200 #define SERIAL_CATCHALL 1 -#elif ENABLED(MachineEnder7) +#elif ANY(MachineEnder7, MachineCR10SmartPro) #define LCD_SERIAL_PORT 2 #define LCD_BAUDRATE 115200 #define SERIAL_CATCHALL 1 @@ -763,7 +769,9 @@ #define MOTHERBOARD BOARD_CREALITY_V427 #elif ENABLED(Creality422) #define MOTHERBOARD BOARD_CREALITY_V4 - #elif ENABLED(MachineEnder3S1) + #elif ENABLED(MachineEnder3S1_F4) + #define MOTHERBOARD BOARD_CREALITY_V24S1_301F4 + #elif ENABLED(MachineEnder3S1) && DISABLED(MachineEnder3S1_F4) #define MOTHERBOARD BOARD_CREALITY_V24S1_301 #elif (ENABLED(MachineCR10Orig) && DISABLED(Melzi_To_SBoardUpgrade)) #define MOTHERBOARD BOARD_MELZI_CREALITY @@ -773,7 +781,9 @@ #define MOTHERBOARD BOARD_CREALITY_V452 #elif ENABLED(MachineCR30) #define MOTHERBOARD BOARD_CREALITY_V4210 - #elif ANY(MachineCR6, MachineCR6Max, MachineCR10Smart, MachineCR10SmartPro) + #elif ENABLED(MachineCR10SmartPro) + #define MOTHERBOARD BOARD_CREALITY_V25S1 + #elif ANY(MachineCR6, MachineCR6Max, MachineCR10Smart) #define MOTHERBOARD BOARD_CREALITY_V453 #elif ENABLED(MachineEnder2Pro) #define MOTHERBOARD BOARD_CREALITY_V423 @@ -1852,7 +1862,7 @@ // Enable this feature if all enabled endstop pins are interrupt-capable. // This will remove the need to poll the interrupt pins, saving many CPU cycles. -#if ANY(MachineEnder3V2, MachineEnder3S1, Creality422, MachineEnder2Pro) && NONE(SKRE3Turbo, SKR14Turbo, SKR14, SKR13) +#if ANY(MachineEnder3V2, MachineEnder3S1, Creality422, MachineEnder2Pro, MachineCR10SmartPro) && NONE(SKRE3Turbo, SKR14Turbo, SKR14, SKR13) #define ENDSTOP_INTERRUPTS_FEATURE #endif @@ -1868,7 +1878,7 @@ * * :[2,3,4,5,6,7] */ -#if ANY(MachineEnder5Plus, CableExtensionNoiseFilter, MachineCR6, MachineCR6Max, MachineEnder6, MachineCR10Smart, MachineCR10SmartPro, MachineSermoonD1) +#if ANY(MachineEnder5Plus, CableExtensionNoiseFilter, MachineCR6, MachineCR6Max, MachineEnder6, MachineCR10Smart, MachineSermoonD1) #define ENDSTOP_NOISE_THRESHOLD 2 #endif @@ -2105,7 +2115,7 @@ * The probe replaces the Z-MIN endstop and is used for Z homing. * (Automatically enables USE_PROBE_FOR_Z_HOMING.) */ -#if NONE(Creality422, Creality427, MachineEnder6, MachineEnder7, MachineCR5, MachineEnder2Pro, MachineEnder3S1) && DISABLED(Creality42XUseZMin) || DISABLED(ABL_BLTOUCH) +#if NONE(Creality422, Creality427, MachineEnder6, MachineEnder7, MachineCR5, MachineEnder2Pro, MachineEnder3S1, MachineCR10SmartPro) && DISABLED(Creality42XUseZMin) || DISABLED(ABL_BLTOUCH) #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN #endif // Force the use of the probe for Z-axis homing @@ -2329,6 +2339,8 @@ #define NOZZLE_TO_PROBE_OFFSET { -45, -5, 0 } #elif ENABLED(MachineEnder3S1) #define NOZZLE_TO_PROBE_OFFSET { -37, -39, -2.0 } +#elif ENABLED(MachineCR10SmartPro) + #define NOZZLE_TO_PROBE_OFFSET { -30, -40, -1.0 } #elif (ENABLED(ABL_BLTOUCH) && ENABLED(HotendStock)) #define NOZZLE_TO_PROBE_OFFSET { -41, -8, 0 } #elif ((ANY(ABL_EZABL, ABL_NCSW)) && ENABLED(HotendStock)) @@ -2826,11 +2838,11 @@ #define Y_MAX_POS 400 #define ClipClearance 15 #elif ENABLED(MachineCR10Max) - #define X_BED_SIZE 450 - #define Y_BED_SIZE 450 + #define X_BED_SIZE 470 + #define Y_BED_SIZE 470 #define Z_MAX_POS 470 - #define X_MAX_POS 450 - #define Y_MAX_POS 450 + #define X_MAX_POS 470 + #define Y_MAX_POS 470 #define ClipClearance 15 #elif ENABLED(MachineS5) #define X_BED_SIZE 500 @@ -2958,6 +2970,11 @@ #if ENABLED(DualFilSensors) #if DISABLED(SKR13, SKR14, SKR14Turbo, SKRPRO11, SKRE3Turbo) #define NUM_RUNOUT_SENSORS 2 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each. + #define ENABLED_ADDON , true + #define DISABLED_ADDON , false + #define MODE_ADDON_7 , 7 + #define MODE_ADDON_2 , 2 + #define MODE_ADDON_1 , 1 #endif #define FIL_RUNOUT2_PIN 15 #else @@ -2968,18 +2985,18 @@ #define MODE_ADDON_2 #define MODE_ADDON_1 #endif - #if NONE(MachineCR10Orig, MachineCR20, MachineEnder3, MachineEnder3V2, MachineEnder4, MachineEnder5, MachineCRX, Melzi_To_SBoardUpgrade) || ANY(AddonFilSensor, lerdgeFilSensor, DualFilSensors) - #define FIL_RUNOUT_ENABLED { true } // Default enabled state for sensors E0[, E1[, E2[, E3...]]]. Override with M591EnnSn followed by M500. + #if NONE(MachineCR10Orig, MachineCR20, MachineEnder3, MachineEnder2, MachineEnder2Pro, MachineEnder3V2, MachineEnder4, MachineEnder5, MachineCRX, Melzi_To_SBoardUpgrade) || ANY(AddonFilSensor, lerdgeFilSensor, DualFilSensors) + #define FIL_RUNOUT_ENABLED { true ENABLED_ADDON} // Default enabled state for sensors E0[, E1[, E2[, E3...]]]. Override with M591EnnSn followed by M500. #else - #define FIL_RUNOUT_ENABLED { false } // Default enabled state for sensors E0[, E1[, E2[, E3...]]]. Override with M591EnnSn followed by M500. + #define FIL_RUNOUT_ENABLED { false DISABLED_ADDON} // Default enabled state for sensors E0[, E1[, E2[, E3...]]]. Override with M591EnnSn followed by M500. #endif #if ENABLED(FilamentEncoder) #define FIL_RUNOUT_MODE { 7 MODE_ADDON_7} // Default mode for sensors E0[, E1[, E2[, E3...]]]. 0:NONE 1:Switch NO 2:Switch NC 7:Motion Sensor Override with M591EnPnn - #elif DISABLED(lerdgeFilSensor) && ( ANY(AddonFilSensor, DualFilSensors) || NONE(MachineCR10Orig, MachineCR20, MachineEnder3, MachineEnder3V2, MachineEnder4, MachineEnder5, MachineCRX, Melzi_To_SBoardUpgrade)) + #elif DISABLED(lerdgeFilSensor) && ( ANY(AddonFilSensor, DualFilSensors) || NONE(MachineCR10Orig, MachineCR20, MachineEnder3, MachineEnder2, MachineEnder2Pro, MachineEnder3V2, MachineEnder4, MachineEnder5, MachineCRX, Melzi_To_SBoardUpgrade)) #define FIL_RUNOUT_MODE { 2 MODE_ADDON_2} // Default mode for sensors E0[, E1[, E2[, E3...]]]. 0:NONE 1:Switch NO 2:Switch NC 7:Motion Sensor Override with M591EnPnn #else - #define FIL_RUNOUT_MODE { 1 } // Default mode for sensors E0[, E1[, E2[, E3...]]]. 0:NONE 1:Switch NO 2:Switch NC 7:Motion Sensor Override with M591EnPnn + #define FIL_RUNOUT_MODE { 1 MODE_ADDON_1} // Default mode for sensors E0[, E1[, E2[, E3...]]]. 0:NONE 1:Switch NO 2:Switch NC 7:Motion Sensor Override with M591EnPnn #endif //#define WATCH_ALL_RUNOUT_SENSORS // Execute runout script on any triggering sensor, not only for the active extruder. // This is automatically enabled for MIXING_EXTRUDERs. @@ -3103,7 +3120,7 @@ * NOTE: Requires a lot of PROGMEM! */ #if ENABLED(MachineLargeROM) - #define DEBUG_LEVELING_FEATURE + //#define DEBUG_LEVELING_FEATURE #endif #if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL, PROBE_MANUALLY) diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h index beb419c2b0..07b5ded275 100644 --- a/Marlin/Configuration_adv.h +++ b/Marlin/Configuration_adv.h @@ -638,7 +638,7 @@ #if ENABLED(MachineEnder3S1) #define E0_AUTO_FAN_PIN PC0 #else - #define E0_AUTO_FAN_PIN -1 + //#define E0_AUTO_FAN_PIN -1 #endif #define E1_AUTO_FAN_PIN -1 #define E2_AUTO_FAN_PIN -1 @@ -2095,7 +2095,7 @@ #endif #endif - #if NONE(ABL_EZABL, ABL_NCSW, ABL_BLTOUCH, ABL_TOUCH_MI, MachineCR6, MachineCR6Max) || ENABLED(MESH_BED_LEVELING) + #if NONE(ABL_EZABL, ABL_NCSW, ABL_BLTOUCH, ABL_TOUCH_MI, MachineCR6, MachineCR6Max, MachineCR10Smart) || ENABLED(MESH_BED_LEVELING) #define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28 #else #define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping @@ -4181,25 +4181,31 @@ #define DualZComm "" #endif + #if ENABLED(EXTENSIBLE_UI) + #define PRINTTIMERSTOP "" + #else + #define PRINTTIMERSTOP "M77\n" + #endif + #define MAIN_MENU_ITEM_1_DESC "Setup" #if (ENABLED(ABL_UBL)) - #define MAIN_MENU_ITEM_1_GCODE "M190S" CommBedTmp "\nG28" DualZComm "\nG29P1\nG29P3\nG29S1\nG29S0\nG29F0.0\nG29A\nM104S215\nG28\nM109S215\nG1X150Y150F5000\nG1Z0\nM500\nM400\nM77\nM117 Set Z Offset" + #define MAIN_MENU_ITEM_1_GCODE "M190S" CommBedTmp "\nG28" DualZComm "\nG29P1\nG29P3\nG29S1\nG29S0\nG29F0.0\nG29A\nM104S215\nG28\nM109S215\nG1X150Y150F5000\nG1Z0\nM500\nM400\n" PRINTTIMERSTOP "M117 Set Z Offset" #elif ENABLED(ABL_BI) - #define MAIN_MENU_ITEM_1_GCODE "M190S" CommBedTmp "\nG28" DualZComm "\nG29\nM400\nM104S215\nG28\nM109S215\nM420S1\nG1X100Y100F5000\nG1Z0\nM500\nM77\nM117 Set Z Offset" + #define MAIN_MENU_ITEM_1_GCODE "M190S" CommBedTmp "\nG28" DualZComm "\nG29\nM400\nM104S215\nG28\nM109S215\nM420S1\nG1X100Y100F5000\nG1Z0\nM500\n" PRINTTIMERSTOP "M117 Set Z Offset" #endif - //#define MAIN_MENU_ITEM_1_CONFIRM // Show a confirmation dialog before this action + #define MAIN_MENU_ITEM_1_CONFIRM // Show a confirmation dialog before this action #define MAIN_MENU_ITEM_2_DESC "PID Tune" #define MAIN_MENU_ITEM_2_GCODE "M106S128\nM303C8S215E0U\nM500\nM117 PID Tune Done" - //#define MAIN_MENU_ITEM_2_CONFIRM // Show a confirmation dialog before this action + #define MAIN_MENU_ITEM_2_CONFIRM // Show a confirmation dialog before this action #define MAIN_MENU_ITEM_3_DESC "Prep for Z Adjust" #define MAIN_MENU_ITEM_3_GCODE "M190S" CommBedTmp "\nM104S215\nG28\nG29L1\nG1 X100Y100F5000\nG1Z0" - //#define MAIN_MENU_ITEM_3_CONFIRM // Show a confirmation dialog before this action + #define MAIN_MENU_ITEM_3_CONFIRM // Show a confirmation dialog before this action #define MAIN_MENU_ITEM_4_DESC "Store Settings" #define MAIN_MENU_ITEM_4_GCODE "M500\nM117 Settings Stored" - //#define MAIN_MENU_ITEM_4_CONFIRM // Show a confirmation dialog before this action + #define MAIN_MENU_ITEM_4_CONFIRM // Show a confirmation dialog before this action //#define MAIN_MENU_ITEM_5_DESC "Run Mesh Validation" //#define MAIN_MENU_ITEM_5_GCODE "G26" diff --git a/Marlin/src/core/boards.h b/Marlin/src/core/boards.h index d1cc971e51..d3f17a1673 100644 --- a/Marlin/src/core/boards.h +++ b/Marlin/src/core/boards.h @@ -354,17 +354,18 @@ #define BOARD_CREALITY_V453 4051 // Creality v4.5.3 (STM32F103RC / STM32F103RE) #define BOARD_CREALITY_V24S1 4052 // Creality v2.4.S1 (STM32F103RC / STM32F103RE) v101 as found in the Ender 7 #define BOARD_CREALITY_V24S1_301 4053 // Creality v2.4.S1_301 (STM32F103RC / STM32F103RE) as found in the Ender 3 S1 -#define BOARD_TRIGORILLA_PRO 4054 // Trigorilla Pro (STM32F103ZE) -#define BOARD_FLY_MINI 4055 // FLYmaker FLY MINI (STM32F103RC) -#define BOARD_FLSUN_HISPEED 4056 // FLSUN HiSpeedV1 (STM32F103VE) -#define BOARD_BEAST 4057 // STM32F103RE Libmaple-based controller -#define BOARD_MINGDA_MPX_ARM_MINI 4058 // STM32F103ZE Mingda MD-16 -#define BOARD_GTM32_PRO_VD 4059 // STM32F103VE controller -#define BOARD_ZONESTAR_ZM3E2 4060 // Zonestar ZM3E2 (STM32F103RC) -#define BOARD_ZONESTAR_ZM3E4 4061 // Zonestar ZM3E4 V1 (STM32F103VC) -#define BOARD_ZONESTAR_ZM3E4V2 4062 // Zonestar ZM3E4 V2 (STM32F103VC) -#define BOARD_ERYONE_ERY32_MINI 4063 // Eryone Ery32 mini (STM32F103VE) -#define BOARD_PANDA_PI_V29 4064 // Panda Pi V2.9 - Standalone (STM32F103RC) +#define BOARD_CREALITY_V25S1 4054 // Creality v4.5.1 (STM32F103RE) as found in the CR10 Smart Pro +#define BOARD_TRIGORILLA_PRO 4055 // Trigorilla Pro (STM32F103ZE) +#define BOARD_FLY_MINI 4056 // FLYmaker FLY MINI (STM32F103RC) +#define BOARD_FLSUN_HISPEED 4057 // FLSUN HiSpeedV1 (STM32F103VE) +#define BOARD_BEAST 4058 // STM32F103RE Libmaple-based controller +#define BOARD_MINGDA_MPX_ARM_MINI 4059 // STM32F103ZE Mingda MD-16 +#define BOARD_GTM32_PRO_VD 4060 // STM32F103VE controller +#define BOARD_ZONESTAR_ZM3E2 4061 // Zonestar ZM3E2 (STM32F103RC) +#define BOARD_ZONESTAR_ZM3E4 4062 // Zonestar ZM3E4 V1 (STM32F103VC) +#define BOARD_ZONESTAR_ZM3E4V2 4063 // Zonestar ZM3E4 V2 (STM32F103VC) +#define BOARD_ERYONE_ERY32_MINI 4064 // Eryone Ery32 mini (STM32F103VE) +#define BOARD_PANDA_PI_V29 4065 // Panda Pi V2.9 - Standalone (STM32F103RC) // // ARM Cortex-M4F @@ -417,6 +418,7 @@ #define BOARD_MKS_EAGLE 4237 // MKS Eagle (STM32F407VE) #define BOARD_ARTILLERY_RUBY 4238 // Artillery Ruby (STM32F401RC) #define BOARD_FYSETC_SPIDER_V2_2 4239 // FYSETC Spider V2.2 (STM32F446VE) +#define BOARD_CREALITY_V24S1_301F4 4240 // Creality v2.4.S1_301F4 (STM32F401RC) as found in the Ender-3 S1 F4 // // ARM Cortex M7 diff --git a/Marlin/src/gcode/bedlevel/abl/G29.cpp b/Marlin/src/gcode/bedlevel/abl/G29.cpp index ac8eff0e95..af3daf2b96 100644 --- a/Marlin/src/gcode/bedlevel/abl/G29.cpp +++ b/Marlin/src/gcode/bedlevel/abl/G29.cpp @@ -941,7 +941,7 @@ G29_TYPE GcodeSuite::G29() { #endif TERN_(HAS_DWIN_E3V2_BASIC, DWIN_LevelingDone()); - + TERN_(EXTENSIBLE_UI, ExtUI::onLevelingDone()); TERN_(HAS_MULTI_HOTEND, if (abl.tool_index != 0) tool_change(abl.tool_index)); report_current_position(); diff --git a/Marlin/src/inc/Conditionals_LCD.h b/Marlin/src/inc/Conditionals_LCD.h index e03eefefae..013e7fe9b0 100644 --- a/Marlin/src/inc/Conditionals_LCD.h +++ b/Marlin/src/inc/Conditionals_LCD.h @@ -491,7 +491,7 @@ #ifndef LCD_SERIAL_PORT #if MB(BTT_SKR_MINI_E3_V1_0, BTT_SKR_MINI_E3_V1_2, BTT_SKR_MINI_E3_V2_0, BTT_SKR_MINI_E3_V3_0, BTT_SKR_E3_TURBO) #define LCD_SERIAL_PORT 1 - #elif MB(CREALITY_V24S1_301) + #elif MB(CREALITY_V24S1_301, CREALITY_V24S1_301F4) #define LCD_SERIAL_PORT 2 // Creality Ender3S1 board #else #define LCD_SERIAL_PORT 3 // Creality 4.x board diff --git a/Marlin/src/lcd/extui/Creality/Creality_DWIN.cpp b/Marlin/src/lcd/extui/Creality/Creality_DWIN.cpp index 59ca8012cb..15f89e8ad9 100644 --- a/Marlin/src/lcd/extui/Creality/Creality_DWIN.cpp +++ b/Marlin/src/lcd/extui/Creality/Creality_DWIN.cpp @@ -90,7 +90,12 @@ void onStartup() rtscheck.recdat.head[1] = rtscheck.snddat.head[1] = FHTWO; memset(rtscheck.databuf, 0, sizeof(rtscheck.databuf)); - delay_ms(500); // Delay to allow screen startup + #if ENABLED(DWINOS_4) + #define DWIN_BOOTUP_DELAY 1500 + #else + #define DWIN_BOOTUP_DELAY 500 + #endif + delay_ms(DWIN_BOOTUP_DELAY); // Delay to allow screen startup SetTouchScreenConfiguration(); rtscheck.RTS_SndData(StartSoundSet, SoundAddr); delay_ms(400); // Delay to allow screen to configure @@ -2100,7 +2105,7 @@ void SetTouchScreenConfiguration() { if (Settings.display_sound) cfg_bits |= 1UL << 3; // 3: audio if (Settings.display_standby) cfg_bits |= 1UL << 2; // 2: backlight on standby if(Settings.screen_rotation==10) cfg_bits |= 1UL << 1; // 1 & 0: Inversion - #if ENABLED(MachineCR10Smart) + #if ANY(MachineCR10Smart, MachineCR10SmartPro ) cfg_bits |= 1UL << 0; // Portrait Mode or 800x480 display has 0 point rotated 90deg from 480x272 display #endif diff --git a/Marlin/src/lcd/extui/dgus_creality_lcd.cpp b/Marlin/src/lcd/extui/dgus_creality_lcd.cpp index 7e402925e3..ccac39299a 100644 --- a/Marlin/src/lcd/extui/dgus_creality_lcd.cpp +++ b/Marlin/src/lcd/extui/dgus_creality_lcd.cpp @@ -215,6 +215,9 @@ bool hasPrintTimer = false; } void onLevelingDone() { + } + void onLevelingDone() { + } #endif diff --git a/Marlin/src/libs/BL24CXX.cpp b/Marlin/src/libs/BL24CXX.cpp index 6407fac670..59352d4380 100644 --- a/Marlin/src/libs/BL24CXX.cpp +++ b/Marlin/src/libs/BL24CXX.cpp @@ -48,7 +48,7 @@ #ifdef __STM32F1__ #define SDA_IN() do{ PIN_MAP[IIC_EEPROM_SDA].gpio_device->regs->CRH &= 0XFFFF0FFF; PIN_MAP[IIC_EEPROM_SDA].gpio_device->regs->CRH |= 8 << 12; }while(0) #define SDA_OUT() do{ PIN_MAP[IIC_EEPROM_SDA].gpio_device->regs->CRH &= 0XFFFF0FFF; PIN_MAP[IIC_EEPROM_SDA].gpio_device->regs->CRH |= 3 << 12; }while(0) -#elif STM32F1 +#elif defined(STM32F1) || defined(STM32F4) #define SDA_IN() SET_INPUT(IIC_EEPROM_SDA) #define SDA_OUT() SET_OUTPUT(IIC_EEPROM_SDA) #endif diff --git a/Marlin/src/pins/pins.h b/Marlin/src/pins/pins.h index 426ce1e48e..a5857b1981 100644 --- a/Marlin/src/pins/pins.h +++ b/Marlin/src/pins/pins.h @@ -583,6 +583,8 @@ #include "stm32f1/pins_CREALITY_V24S1.h" // STM32F1 env:STM32F103RE_creality env:STM32F103RE_creality_xfer env:STM32F103RC_creality env:STM32F103RC_creality_xfer env:STM32F103RE_creality_maple #elif MB(CREALITY_V24S1_301) #include "stm32f1/pins_CREALITY_V24S1_301.h" // STM32F1 env:STM32F103RE_creality env:STM32F103RE_creality_xfer env:STM32F103RC_creality env:STM32F103RC_creality_xfer env:STM32F103RE_creality_maple +#elif MB(CREALITY_V25S1) + #include "stm32f1/pins_CREALITY_V25S1.h" // STM32F1 env:STM32F103RE_creality_smartPro env:STM32F103RE_creality_smartPro_maple #elif MB(TRIGORILLA_PRO) #include "stm32f1/pins_TRIGORILLA_PRO.h" // STM32F1 env:trigorilla_pro env:trigorilla_pro_maple #elif MB(FLY_MINI) @@ -693,6 +695,8 @@ #include "stm32f4/pins_MKS_EAGLE.h" // STM32F4 env:mks_eagle #elif MB(ARTILLERY_RUBY) #include "stm32f4/pins_ARTILLERY_RUBY.h" // STM32F4 env:Artillery_Ruby +#elif MB(CREALITY_V24S1_301F4) + #include "stm32f4/pins_CREALITY_V24S1_301F4.h" // STM32F4 env:STM32F401RC_creality env:STM32F401RC_creality_jlink env:STM32F401RC_creality_stlink // // ARM Cortex M7 diff --git a/Marlin/src/pins/stm32f1/env_validate.h b/Marlin/src/pins/stm32f1/env_validate.h index 2e7b785172..2d325428ac 100644 --- a/Marlin/src/pins/stm32f1/env_validate.h +++ b/Marlin/src/pins/stm32f1/env_validate.h @@ -22,5 +22,11 @@ #pragma once #if NOT_TARGET(__STM32F1__, STM32F1) - #error "Oops! Select an STM32F1 board in 'Tools > Board.'" + #if DISABLED(ALLOW_STM32F4) + #error "Oops! Select an STM32F1 board in 'Tools > Board.'" + #elif NOT_TARGET(STM32F4) + #error "Oops! Select an STM32F4 board in 'Tools > Board.'" + #endif #endif + +#undef ALLOW_STM32F4 diff --git a/Marlin/src/pins/stm32f1/pins_CREALITY_V24S1_301.h b/Marlin/src/pins/stm32f1/pins_CREALITY_V24S1_301.h index fb7198e57c..66ee8af61b 100644 --- a/Marlin/src/pins/stm32f1/pins_CREALITY_V24S1_301.h +++ b/Marlin/src/pins/stm32f1/pins_CREALITY_V24S1_301.h @@ -22,7 +22,8 @@ #pragma once /** - * Creality V24S1_301 (STM32F103RE / STM32F103RC) board pin assignments as found on Ender 3 S1 + * Creality V24S1_301 (STM32F103RE / STM32F103RC) board pin assignments as found on Ender 3 S1. + * Also supports the STM32F4 version of the board with identical pin mapping. */ #include "env_validate.h" @@ -35,8 +36,12 @@ #error "Disable Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN when using BLTOUCH with Creality V24S1-301." #endif -#define BOARD_INFO_NAME "Creality V24S1-301" -#define DEFAULT_MACHINE_NAME "Ender 3 S1" +#ifndef BOARD_INFO_NAME + #define BOARD_INFO_NAME "Creality V24S1-301" +#endif +#ifndef DEFAULT_MACHINE_NAME + #define DEFAULT_MACHINE_NAME "Ender 3 S1" +#endif // // Servos @@ -70,8 +75,8 @@ // // SD Card // -#define ONBOARD_SPI_DEVICE 1 -#define ONBOARD_SD_CS_PIN PA4 // SDSS +#define ONBOARD_SPI_DEVICE 1 +#define ONBOARD_SD_CS_PIN PA4 // SDSS // // M3/M4/M5 - Spindle/Laser Control @@ -80,9 +85,10 @@ //#define HEATER_0_PIN -1 //#define HEATER_BED_PIN -1 #define FAN_PIN -1 - #define SPINDLE_LASER_ENA_PIN PA0 // FET 1 - #define SPINDLE_LASER_PWM_PIN PA0 // Bed FET - #define SPINDLE_DIR_PIN PA0 // FET 4 + #define SPINDLE_LASER_ENA_PIN PC0 // FET 1 + #define SPINDLE_LASER_PWM_PIN PC0 // Bed FET + #define SPINDLE_DIR_PIN PC0 // FET 4 + #define LASER_SOFT_PWM_PIN PC0 #endif #include "pins_CREALITY_V4.h" diff --git a/Marlin/src/pins/stm32f1/pins_CREALITY_V25S1.h b/Marlin/src/pins/stm32f1/pins_CREALITY_V25S1.h new file mode 100644 index 0000000000..f514d1c75e --- /dev/null +++ b/Marlin/src/pins/stm32f1/pins_CREALITY_V25S1.h @@ -0,0 +1,157 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2021 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Creality v2.4.S1 (STM32F103RE / STM32F103RC) v101 as found in the Ender 7 board pin assignments + */ + +#define BOARD_INFO_NAME "Creality v2.5.S1" +#define DEFAULT_MACHINE_NAME "Creality3D" + +// +// EEPROM +// +#if NO_EEPROM_SELECTED + // FLASH + //#define FLASH_EEPROM_EMULATION + + // I2C + #define IIC_BL24CXX_EEPROM // EEPROM on I2C-0 used only for display settings + #if ENABLED(IIC_BL24CXX_EEPROM) + #define IIC_EEPROM_SDA PA11 + #define IIC_EEPROM_SCL PA12 + #define MARLIN_EEPROM_SIZE 0x800 // 2Kb (24C16) + #else + #define SDCARD_EEPROM_EMULATION // SD EEPROM until all EEPROM is BL24CXX + #define MARLIN_EEPROM_SIZE 0x800 // 2Kb + #endif + + // SPI + //#define SPI_EEPROM // EEPROM on SPI-0 + //#define SPI_CHAN_EEPROM1 ? + //#define SPI_EEPROM1_CS ? + + // 2K EEPROM + //#define SPI_EEPROM2_CS ? + + // 32Mb FLASH + //#define SPI_FLASH_CS ? +#endif + +// +// Limit Switches +// +#define X_STOP_PIN PC4 +#define Y_STOP_PIN PC5 + +// +// Servos +// +#if ENABLED(BLTOUCH) + #define Z_MIN_PROBE_PIN PC15 // BLTouch IN PIN + #define SERVO0_PIN PC14 // BLTouch OUT PIN + #define Z_MIN_PIN -1 +#elif ENABLED(PROBE_ACTIVATION_SWITCH) + #define Z_MIN_PIN PC15 + #define PROBE_TARE_PIN PC14 + #define PROBE_ACTIVATION_SWITCH_PIN PB2 +#else + #define Z_MIN_PIN PC15 +#endif + +// +// Filament Runout Sensor +// +#if ENABLED(FILAMENT_RUNOUT_SENSOR) + #define FIL_RUNOUT_PIN PA15 // "Pulled-high" +#endif + +// +// Steppers +// +#define X_ENABLE_PIN PC3 +#define X_STEP_PIN PB8 +#define X_DIR_PIN PB7 + +#define Y_ENABLE_PIN PC3 +#define Y_STEP_PIN PB6 +#define Y_DIR_PIN PB5 + +#define Z_ENABLE_PIN PC3 +#define Z_STEP_PIN PB4 +#define Z_DIR_PIN PB3 + +#define E0_ENABLE_PIN PC3 +#define E0_STEP_PIN PC2 +#define E0_DIR_PIN PB9 + +// +// Release PB4 (Y_ENABLE_PIN) from JTAG NRST role +// +#define DISABLE_DEBUG + +// +// Temperature Sensors +// +#define TEMP_0_PIN PB1 // TH1 +#define TEMP_BED_PIN PB0 // TB1 + +// +// Heaters / Fans +// +#define HEATER_0_PIN PB14 // HEATER1 +#define HEATER_BED_PIN PB13 // HOT BED + +#define FAN_PIN PB15 // FAN +#ifndef E0_AUTO_FAN_PIN + #define E0_AUTO_FAN_PIN PC13 // FAN +#endif +#define FAN_SOFT_PWM + +// +// SD Card +// +#define SD_DETECT_PIN PC7 +#define SDCARD_CONNECTION ONBOARD +#define ON_BOARD_SPI_DEVICE 1 +#define ONBOARD_SD_CS_PIN PC12 // SDSS +#define SDIO_SUPPORT +#define NO_SD_HOST_DRIVE // This board's SD is only seen by the printer + +#define CASE_LIGHT_PIN PA7 + +// +// Suicide Power +// +#define PS_ON_PIN PA0 +#define MOTOR_CIRCUIT_PIN PA1 + +// +// Motor Protect +// +#define MOTOR_PROTECT_PIN PC0 + +// +// WiFI Reset +// +#define RESET_WIFI_PIN PB12 diff --git a/Marlin/src/pins/stm32f1/pins_CREALITY_V4.h b/Marlin/src/pins/stm32f1/pins_CREALITY_V4.h index d6d4966241..535f049351 100644 --- a/Marlin/src/pins/stm32f1/pins_CREALITY_V4.h +++ b/Marlin/src/pins/stm32f1/pins_CREALITY_V4.h @@ -40,6 +40,13 @@ #define BOARD_NO_NATIVE_USB +// +// Release PB4 (Y_ENABLE_PIN) from JTAG NRST role +// +#ifndef DISABLE_DEBUG + #define DISABLE_DEBUG +#endif + // // EEPROM // @@ -122,11 +129,6 @@ #endif #define E0_ENABLE_PIN X_ENABLE_PIN -// -// Release PB4 (Y_ENABLE_PIN) from JTAG NRST role -// -#define DISABLE_DEBUG - // // Temperature Sensors // diff --git a/Marlin/src/pins/stm32f4/pins_CREALITY_V24S1_301F4.h b/Marlin/src/pins/stm32f4/pins_CREALITY_V24S1_301F4.h new file mode 100644 index 0000000000..883640d577 --- /dev/null +++ b/Marlin/src/pins/stm32f4/pins_CREALITY_V24S1_301F4.h @@ -0,0 +1,38 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2022 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Creality V24S1_301F4 (STM32F401RC) board pin assignments as found on Ender 3 S1. + */ + +#ifndef BOARD_INFO_NAME + #define BOARD_INFO_NAME "Creality V24S1-301F4" +#endif +#ifndef DEFAULT_MACHINE_NAME + #define DEFAULT_MACHINE_NAME "Ender-3 S1 F4" +#endif + +#define DISABLE_DEBUG false // DISABLE_(DEBUG|JTAG) is not supported for STM32F4. +#define ALLOW_STM32F4 + +#include "../stm32f1/pins_CREALITY_V24S1_301.h" diff --git a/README.md b/README.md index 200f1cae11..69b0c5ef35 100644 --- a/README.md +++ b/README.md @@ -82,6 +82,8 @@ Marlin Firmware Discord - https://discord.gg/n5NJ59y - Added support for runtime configurable runout sensors matching RRF M591 including type and polarity - Moved E3V2/S1 machines to Marlin Display - - Due to the ongoing fued between developers and GPL violations involved with both the Pro/Enahnced UI and the Jyers UI, we have decided to support neither and stay away from the conflict as much as possible. The Marlin UI has more configuration functionality and the menus are more adaptive to the configuration of the machine. This is based off of the default Marlin menu system and will be the most stable long term going forward as well. The cosmetics and graphical icons may not be as nice as with the other UI's however we belive the added functionality more than makes up for it. + - Removed non-touchscreen 8 bit UBL builds due to RAM constraints + - Removed Pre-Built Melzi / Sanguino files. These are legacy and no longer actively supported. Its recommended to purchase replacement 32bit motherboards for any machine still using it from https://amzn.to/3KdqyI8 ## Primary Notes for DW7.4.5 - Added support for CR10 Smart - Thanks to Tinymachines for providing the machine diff --git a/buildroot/share/PlatformIO/boards/marlin_CREALITY_STM32F401RC.json b/buildroot/share/PlatformIO/boards/marlin_CREALITY_STM32F401RC.json new file mode 100644 index 0000000000..82f49fa815 --- /dev/null +++ b/buildroot/share/PlatformIO/boards/marlin_CREALITY_STM32F401RC.json @@ -0,0 +1,65 @@ +{ + "build": { + "core": "stm32", + "cpu": "cortex-m4", + "extra_flags": "-DSTM32F401xx", + "f_cpu": "84000000L", + "hwids": [ + [ + "0x1EAF", + "0x0003" + ], + [ + "0x0483", + "0x3748" + ] + ], + "ldscript": "ldscript.ld", + "mcu": "stm32f401rct6", + "variant": "MARLIN_CREALITY_STM32F401RC" + }, + "debug": { + "jlink_device": "STM32F401RC", + "openocd_target": "stm32f4x", + "svd_path": "STM32F40x.svd", + "tools": { + "stlink": { + "server": { + "arguments": [ + "-f", + "scripts/interface/stlink.cfg", + "-c", + "transport select hla_swd", + "-f", + "scripts/target/stm32f4x.cfg", + "-c", + "reset_config none" + ], + "executable": "bin/openocd", + "package": "tool-openocd" + } + } + } + }, + "frameworks": [ + "arduino", + "stm32cube" + ], + "name": "STM32F401RC (64k RAM. 256k Flash)", + "upload": { + "disable_flushing": false, + "maximum_ram_size": 65536, + "maximum_size": 262144, + "protocol": "stlink", + "protocols": [ + "stlink", + "dfu", + "jlink" + ], + "require_upload_port": true, + "use_1200bps_touch": false, + "wait_for_upload_port": false + }, + "url": "https://www.st.com/en/microcontrollers-microprocessors/stm32f401rc.html", + "vendor": "Generic" +} diff --git a/buildroot/share/PlatformIO/ldscripts/crealityPro.ld b/buildroot/share/PlatformIO/ldscripts/crealityPro.ld new file mode 100644 index 0000000000..442c5c7507 --- /dev/null +++ b/buildroot/share/PlatformIO/ldscripts/crealityPro.ld @@ -0,0 +1,14 @@ +MEMORY +{ + ram (rwx) : ORIGIN = 0x20000000, LENGTH = 64K - 40 + rom (rx) : ORIGIN = 0x08010000, LENGTH = 512K - 64K +} + +/* Provide memory region aliases for common.inc */ +REGION_ALIAS("REGION_TEXT", rom); +REGION_ALIAS("REGION_DATA", ram); +REGION_ALIAS("REGION_BSS", ram); +REGION_ALIAS("REGION_RODATA", rom); + +/* Let common.inc handle the real work. */ +INCLUDE common.inc \ No newline at end of file diff --git a/buildroot/share/PlatformIO/variants/MARLIN_CREALITY_STM32F401RC/PeripheralPins.c b/buildroot/share/PlatformIO/variants/MARLIN_CREALITY_STM32F401RC/PeripheralPins.c new file mode 100644 index 0000000000..418ef5aa7a --- /dev/null +++ b/buildroot/share/PlatformIO/variants/MARLIN_CREALITY_STM32F401RC/PeripheralPins.c @@ -0,0 +1,252 @@ +/* + ******************************************************************************* + * Copyright (c) 2019, STMicroelectronics + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + ******************************************************************************* + * Automatically generated from STM32F401R[(B-C)|(D-E)]Tx.xml + */ +#include "Arduino.h" +#include "PeripheralPins.h" + +/* ===== + * Note: Commented lines are alternative possibilities which are not used per default. + * If you change them, you will have to know what you do + * ===== + */ + +//*** ADC *** + +#ifdef HAL_ADC_MODULE_ENABLED +WEAK const PinMap PinMap_ADC[] = { + {PA_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 0, 0)}, // ADC1_IN0 + {PA_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 1, 0)}, // ADC1_IN1 + {PA_2, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 2, 0)}, // ADC1_IN2 + {PA_3, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 3, 0)}, // ADC1_IN3 + {PA_4, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 4, 0)}, // ADC1_IN4 + {PA_5, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC1_IN5 + {PA_6, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC1_IN6 + {PA_7, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC1_IN7 + {PB_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC1_IN8 + {PB_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 9, 0)}, // ADC1_IN9 + {PC_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC1_IN10 + {PC_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC1_IN11 + {PC_2, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC1_IN12 + {PC_3, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 13, 0)}, // ADC1_IN13 + {PC_4, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 14, 0)}, // ADC1_IN14 + {PC_5, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 15, 0)}, // ADC1_IN15 + {NC, NP, 0} +}; +#endif + +//*** No DAC *** + +//*** I2C *** + +#ifdef HAL_I2C_MODULE_ENABLED +WEAK const PinMap PinMap_I2C_SDA[] = { + {PB_3, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF9_I2C2)}, + {PB_4, I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF9_I2C3)}, + {PB_7, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)}, + {PB_9, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)}, + {PC_9, I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C3)}, + {NC, NP, 0} +}; + +WEAK const PinMap PinMap_I2C_SCL[] = { + {PA_8, I2C3, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C3)}, + {PB_6, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)}, + {PB_8, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)}, + {PB_10, I2C2, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C2)}, + {NC, NP, 0} +}; +#endif + +//*** PWM *** + +#ifdef HAL_TIM_MODULE_ENABLED +WEAK const PinMap PinMap_PWM[] = { + //{PA_0, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 1, 0)}, // TIM2_CH1 + {PA_0, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 1, 0)}, // TIM5_CH1 + //{PA_1, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 2, 0)}, // TIM2_CH2 + {PA_1, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 2, 0)}, // TIM5_CH2 + //{PA_2, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 3, 0)}, // TIM2_CH3 + {PA_2, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 3, 0)}, // TIM5_CH3 + //{PA_2, TIM9, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM9, 1, 0)}, // TIM9_CH1 + //{PA_3, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 4, 0)}, // TIM2_CH4 + {PA_3, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 4, 0)}, // TIM5_CH4 + //{PA_3, TIM9, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM9, 2, 0)}, // TIM9_CH2 + {PA_5, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 1, 0)}, // TIM2_CH1 + {PA_6, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 1, 0)}, // TIM3_CH1 + //{PA_7, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N + {PA_7, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2 + {PA_8, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 0)}, // TIM1_CH1 + {PA_9, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 0)}, // TIM1_CH2 + {PA_10, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 0)}, // TIM1_CH3 + {PA_11, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 4, 0)}, // TIM1_CH4 + {PA_15, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 1, 0)}, // TIM2_CH1 + //{PB_0, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 1)}, // TIM1_CH2N + {PB_0, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 3, 0)}, // TIM3_CH3 + //{PB_1, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 1)}, // TIM1_CH3N + {PB_1, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 4, 0)}, // TIM3_CH4 + {PB_3, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 2, 0)}, // TIM2_CH2 + {PB_4, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 1, 0)}, // TIM3_CH1 + {PB_5, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2 + {PB_6, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 1, 0)}, // TIM4_CH1 + {PB_7, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 2, 0)}, // TIM4_CH2 + {PB_8, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 3, 0)}, // TIM4_CH3 + //{PB_8, TIM10, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM10, 1, 0)}, // TIM10_CH1 + {PB_9, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 4, 0)}, // TIM4_CH4 + //{PB_9, TIM11, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF3_TIM11, 1, 0)}, // TIM11_CH1 + {PB_10, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 3, 0)}, // TIM2_CH3 + {PB_13, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 1)}, // TIM1_CH1N + {PB_14, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 1)}, // TIM1_CH2N + {PB_15, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 1)}, // TIM1_CH3N + {PC_6, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 1, 0)}, // TIM3_CH1 + {PC_7, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 2, 0)}, // TIM3_CH2 + {PC_8, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 3, 0)}, // TIM3_CH3 + {PC_9, TIM3, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM3, 4, 0)}, // TIM3_CH4 + {NC, NP, 0} +}; +#endif + +//*** SERIAL *** + +#ifdef HAL_UART_MODULE_ENABLED +WEAK const PinMap PinMap_UART_TX[] = { + {PA_2, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)}, + {PA_9, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)}, + {PA_11, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)}, + {PB_6, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)}, + {PC_6, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)}, + {NC, NP, 0} +}; + +WEAK const PinMap PinMap_UART_RX[] = { + {PA_3, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)}, + {PA_10, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)}, + {PA_12, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)}, + {PB_7, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)}, + {PC_7, USART6, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF8_USART6)}, + {NC, NP, 0} +}; + +WEAK const PinMap PinMap_UART_RTS[] = { + {PA_1, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)}, + {PA_12, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)}, + {NC, NP, 0} +}; + +WEAK const PinMap PinMap_UART_CTS[] = { + {PA_0, USART2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART2)}, + {PA_11, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)}, + {NC, NP, 0} +}; +#endif + +//*** SPI *** + +#ifdef HAL_SPI_MODULE_ENABLED +WEAK const PinMap PinMap_SPI_MOSI[] = { + {PA_7, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + //{PB_5, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + {PB_5, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)}, + {PB_15, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, + {PC_3, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, + {PC_12, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)}, + {NC, NP, 0} +}; + +WEAK const PinMap PinMap_SPI_MISO[] = { + {PA_6, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + //{PB_4, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + {PB_4, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)}, + {PB_14, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, + {PC_2, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, + {PC_11, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)}, + {NC, NP, 0} +}; + +WEAK const PinMap PinMap_SPI_SCLK[] = { + {PA_5, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + //{PB_3, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + {PB_3, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)}, + {PB_10, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, + {PB_13, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, + {PC_10, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)}, + {NC, NP, 0} +}; + +WEAK const PinMap PinMap_SPI_SSEL[] = { + {PA_4, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + //{PA_4, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)}, + //{PA_15, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + {PA_15, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)}, + {PB_9, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, + {PB_12, SPI2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI2)}, + {NC, NP, 0} +}; +#endif + +//*** No CAN *** + +//*** No ETHERNET *** + +//*** No QUADSPI *** + +//*** USB *** + +#ifdef HAL_PCD_MODULE_ENABLED +WEAK const PinMap PinMap_USB_OTG_FS[] = { +#ifndef ARDUINO_CoreBoard_F401RC + {PA_8, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_SOF + {PA_9, USB_OTG_FS, STM_PIN_DATA(STM_MODE_INPUT, GPIO_NOPULL, GPIO_AF_NONE)}, // USB_OTG_FS_VBUS + {PA_10, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_ID +#endif + {PA_11, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_DM + {PA_12, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_DP + {NC, NP, 0} +}; +#endif + +//*** No USB_OTG_HS *** + +//*** SD *** + +#ifdef HAL_SD_MODULE_ENABLED +WEAK const PinMap PinMap_SD[] = { + {PB_8, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D4 + {PB_9, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D5 + {PC_6, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D6 + {PC_7, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D7 + {PC_8, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D0 + {PC_9, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D1 + {PC_10, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D2 + {PC_11, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF12_SDIO)}, // SDIO_D3 + {PC_12, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF12_SDIO)}, // SDIO_CK + {PD_2, SDIO, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF12_SDIO)}, // SDIO_CMD + {NC, NP, 0} +}; +#endif diff --git a/buildroot/share/PlatformIO/variants/MARLIN_CREALITY_STM32F401RC/PinNamesVar.h b/buildroot/share/PlatformIO/variants/MARLIN_CREALITY_STM32F401RC/PinNamesVar.h new file mode 100644 index 0000000000..e1536bcf30 --- /dev/null +++ b/buildroot/share/PlatformIO/variants/MARLIN_CREALITY_STM32F401RC/PinNamesVar.h @@ -0,0 +1,33 @@ +/* SYS_WKUP */ +#ifdef PWR_WAKEUP_PIN1 + SYS_WKUP1 = PA_0, +#endif +#ifdef PWR_WAKEUP_PIN2 + SYS_WKUP2 = NC, +#endif +#ifdef PWR_WAKEUP_PIN3 + SYS_WKUP3 = NC, +#endif +#ifdef PWR_WAKEUP_PIN4 + SYS_WKUP4 = NC, +#endif +#ifdef PWR_WAKEUP_PIN5 + SYS_WKUP5 = NC, +#endif +#ifdef PWR_WAKEUP_PIN6 + SYS_WKUP6 = NC, +#endif +#ifdef PWR_WAKEUP_PIN7 + SYS_WKUP7 = NC, +#endif +#ifdef PWR_WAKEUP_PIN8 + SYS_WKUP8 = NC, +#endif +/* USB */ +#ifdef USBCON + USB_OTG_FS_SOF = PA_8, + USB_OTG_FS_VBUS = PA_9, + USB_OTG_FS_ID = PA_10, + USB_OTG_FS_DM = PA_11, + USB_OTG_FS_DP = PA_12, +#endif \ No newline at end of file diff --git a/buildroot/share/PlatformIO/variants/MARLIN_CREALITY_STM32F401RC/hal_conf_custom.h b/buildroot/share/PlatformIO/variants/MARLIN_CREALITY_STM32F401RC/hal_conf_custom.h new file mode 100644 index 0000000000..1dd047bb90 --- /dev/null +++ b/buildroot/share/PlatformIO/variants/MARLIN_CREALITY_STM32F401RC/hal_conf_custom.h @@ -0,0 +1,495 @@ +/** + ****************************************************************************** + * @file stm32f4xx_hal_conf.h + * @brief HAL configuration file. + ****************************************************************************** + * @attention + * + *

© Copyright (c) 2017 STMicroelectronics. + * All rights reserved.

+ * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F4xx_HAL_CONF_CUSTOM +#define __STM32F4xx_HAL_CONF_CUSTOM + +#ifdef __cplusplus +extern "C" { +#endif + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ + +/* ########################## Module Selection ############################## */ + /** + * @brief This is the list of modules to be used in the HAL driver + */ +#define HAL_MODULE_ENABLED +#define HAL_ADC_MODULE_ENABLED +#define HAL_CRC_MODULE_ENABLED +#define HAL_DMA_MODULE_ENABLED +#define HAL_FLASH_MODULE_ENABLED +#define HAL_GPIO_MODULE_ENABLED +#define HAL_I2C_MODULE_ENABLED +#define HAL_IWDG_MODULE_ENABLED +#define HAL_PWR_MODULE_ENABLED +#define HAL_RCC_MODULE_ENABLED +#define HAL_RTC_MODULE_ENABLED +#define HAL_SPI_MODULE_ENABLED +#define HAL_TIM_MODULE_ENABLED +#define HAL_CORTEX_MODULE_ENABLED +//#define HAL_PCD_MODULE_ENABLED // Automatically added if any type of USB is enabled, as in Arduino IDE. (STM32 v3.10700.191028) + +//#define HAL_CAN_MODULE_ENABLED +//#define HAL_CAN_LEGACY_MODULE_ENABLED +//#define HAL_CEC_MODULE_ENABLED +//#define HAL_CRYP_MODULE_ENABLED +//#define HAL_DAC_MODULE_ENABLED +//#define HAL_DCMI_MODULE_ENABLED +//#define HAL_DMA2D_MODULE_ENABLED +//#define HAL_ETH_MODULE_ENABLED +//#define HAL_NAND_MODULE_ENABLED +//#define HAL_NOR_MODULE_ENABLED +//#define HAL_PCCARD_MODULE_ENABLED +//#define HAL_SRAM_MODULE_ENABLED +//#define HAL_SDRAM_MODULE_ENABLED +//#define HAL_HASH_MODULE_ENABLED +//#define HAL_EXTI_MODULE_ENABLED +//#define HAL_SMBUS_MODULE_ENABLED +//#define HAL_I2S_MODULE_ENABLED +//#define HAL_LTDC_MODULE_ENABLED +//#define HAL_DSI_MODULE_ENABLED +//#define HAL_QSPI_MODULE_ENABLED +//#define HAL_RNG_MODULE_ENABLED +//#define HAL_SAI_MODULE_ENABLED +#define HAL_SD_MODULE_ENABLED +//#define HAL_UART_MODULE_ENABLED +//#define HAL_USART_MODULE_ENABLED +//#define HAL_IRDA_MODULE_ENABLED +//#define HAL_SMARTCARD_MODULE_ENABLED +//#define HAL_WWDG_MODULE_ENABLED +//#define HAL_HCD_MODULE_ENABLED +//#define HAL_FMPI2C_MODULE_ENABLED +//#define HAL_SPDIFRX_MODULE_ENABLED +//#define HAL_DFSDM_MODULE_ENABLED +//#define HAL_LPTIM_MODULE_ENABLED +//#define HAL_MMC_MODULE_ENABLED + +/* ########################## HSE/HSI Values adaptation ##################### */ +/** + * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSE is used as system clock source, directly or through the PLL). + */ +#ifndef HSE_VALUE +#define HSE_VALUE 8000000U /*!< Value of the External oscillator in Hz */ +#endif /* HSE_VALUE */ + +#ifndef HSE_STARTUP_TIMEOUT +#define HSE_STARTUP_TIMEOUT 100U /*!< Time out for HSE start up, in ms */ +#endif /* HSE_STARTUP_TIMEOUT */ + +/** + * @brief Internal High Speed oscillator (HSI) value. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSI is used as system clock source, directly or through the PLL). + */ +#ifndef HSI_VALUE +#define HSI_VALUE 16000000U /*!< Value of the Internal oscillator in Hz */ +#endif /* HSI_VALUE */ + +/** + * @brief Internal Low Speed oscillator (LSI) value. + */ +#ifndef LSI_VALUE +#define LSI_VALUE 32000U /*!< LSI Typical Value in Hz */ +#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz +The real value may vary depending on the variations +in voltage and temperature. */ +/** + * @brief External Low Speed oscillator (LSE) value. + */ +#ifndef LSE_VALUE +#define LSE_VALUE 32768U /*!< Value of the External Low Speed oscillator in Hz */ +#endif /* LSE_VALUE */ + +#ifndef LSE_STARTUP_TIMEOUT +#define LSE_STARTUP_TIMEOUT 5000U /*!< Time out for LSE start up, in ms */ +#endif /* LSE_STARTUP_TIMEOUT */ + +/** + * @brief External clock source for I2S peripheral + * This value is used by the I2S HAL module to compute the I2S clock source + * frequency, this source is inserted directly through I2S_CKIN pad. + */ +#ifndef EXTERNAL_CLOCK_VALUE +#define EXTERNAL_CLOCK_VALUE 12288000U /*!< Value of the External oscillator in Hz*/ +#endif /* EXTERNAL_CLOCK_VALUE */ + +/* Tip: To avoid modifying this file each time you need to use different HSE, + === you can define the HSE value in your toolchain compiler preprocessor. */ + +/* ########################### System Configuration ######################### */ +/** + * @brief This is the HAL system configuration section + */ +#if !defined (VDD_VALUE) +#define VDD_VALUE 3300U /*!< Value of VDD in mv */ +#endif +#if !defined (TICK_INT_PRIORITY) +#define TICK_INT_PRIORITY 0x00U /*!< tick interrupt priority */ +#endif +#if !defined (USE_RTOS) +#define USE_RTOS 0U +#endif +#if !defined (PREFETCH_ENABLE) +#define PREFETCH_ENABLE 1U +#endif +#if !defined (INSTRUCTION_CACHE_ENABLE) +#define INSTRUCTION_CACHE_ENABLE 1U +#endif +#if !defined (DATA_CACHE_ENABLE) +#define DATA_CACHE_ENABLE 1U +#endif + +#define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */ +#define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */ +#define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */ +#define USE_HAL_CRYP_REGISTER_CALLBACKS 0U /* CRYP register callback disabled */ +#define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */ +#define USE_HAL_DCMI_REGISTER_CALLBACKS 0U /* DCMI register callback disabled */ +#define USE_HAL_DFSDM_REGISTER_CALLBACKS 0U /* DFSDM register callback disabled */ +#define USE_HAL_DMA2D_REGISTER_CALLBACKS 0U /* DMA2D register callback disabled */ +#define USE_HAL_DSI_REGISTER_CALLBACKS 0U /* DSI register callback disabled */ +#define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */ +#define USE_HAL_HASH_REGISTER_CALLBACKS 0U /* HASH register callback disabled */ +#define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */ +#define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */ +#define USE_HAL_FMPI2C_REGISTER_CALLBACKS 0U /* FMPI2C register callback disabled */ +#define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */ +#define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */ +#define USE_HAL_LPTIM_REGISTER_CALLBACKS 0U /* LPTIM register callback disabled */ +#define USE_HAL_LTDC_REGISTER_CALLBACKS 0U /* LTDC register callback disabled */ +#define USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */ +#define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */ +#define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */ +#define USE_HAL_PCCARD_REGISTER_CALLBACKS 0U /* PCCARD register callback disabled */ +#define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */ +#define USE_HAL_QSPI_REGISTER_CALLBACKS 0U /* QSPI register callback disabled */ +#define USE_HAL_RNG_REGISTER_CALLBACKS 0U /* RNG register callback disabled */ +#define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */ +#define USE_HAL_SAI_REGISTER_CALLBACKS 0U /* SAI register callback disabled */ +#define USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */ +#define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */ +#define USE_HAL_SDRAM_REGISTER_CALLBACKS 0U /* SDRAM register callback disabled */ +#define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */ +#define USE_HAL_SPDIFRX_REGISTER_CALLBACKS 0U /* SPDIFRX register callback disabled */ +#define USE_HAL_SMBUS_REGISTER_CALLBACKS 0U /* SMBUS register callback disabled */ +#define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */ +#define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */ +#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */ +#define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */ +#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */ + +/* ########################## Assert Selection ############################## */ +/** + * @brief Uncomment the line below to expanse the "assert_param" macro in the + * HAL drivers code + */ +/* #define USE_FULL_ASSERT 1U */ + +/* ################## Ethernet peripheral configuration ##################### */ + +/* Section 1 : Ethernet peripheral configuration */ + +/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */ +#define MAC_ADDR0 2U +#define MAC_ADDR1 0U +#define MAC_ADDR2 0U +#define MAC_ADDR3 0U +#define MAC_ADDR4 0U +#define MAC_ADDR5 0U + +/* Definition of the Ethernet driver buffers size and count */ +#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ +#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ +#define ETH_RXBUFNB ((uint32_t)4U) /* 4 Rx buffers of size ETH_RX_BUF_SIZE */ +#define ETH_TXBUFNB ((uint32_t)4U) /* 4 Tx buffers of size ETH_TX_BUF_SIZE */ + +/* Section 2: PHY configuration section */ + +/* DP83848_PHY_ADDRESS Address*/ +#define DP83848_PHY_ADDRESS 0x01U +/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ +#define PHY_RESET_DELAY 0x000000FFU +/* PHY Configuration delay */ +#define PHY_CONFIG_DELAY 0x00000FFFU + +#define PHY_READ_TO 0x0000FFFFU +#define PHY_WRITE_TO 0x0000FFFFU + +/* Section 3: Common PHY Registers */ + +#define PHY_BCR ((uint16_t)0x0000) /*!< Transceiver Basic Control Register */ +#define PHY_BSR ((uint16_t)0x0001) /*!< Transceiver Basic Status Register */ + +#define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */ +#define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */ +#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */ +#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */ +#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */ +#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */ +#define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */ +#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */ +#define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */ +#define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */ + +#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */ +#define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */ +#define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */ + +/* Section 4: Extended PHY Registers */ +#define PHY_SR ((uint16_t)0x10U) /*!< PHY status register Offset */ + +#define PHY_SPEED_STATUS ((uint16_t)0x0002U) /*!< PHY Speed mask */ +#define PHY_DUPLEX_STATUS ((uint16_t)0x0004U) /*!< PHY Duplex mask */ + +/* ################## SPI peripheral configuration ########################## */ + +/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver + * Activated: CRC code is present inside driver + * Deactivated: CRC code cleaned from driver + */ +#ifndef USE_SPI_CRC +#define USE_SPI_CRC 0U +#endif + +/* Includes ------------------------------------------------------------------*/ +/** + * @brief Include module's header file + */ + +#ifdef HAL_RCC_MODULE_ENABLED +#include "stm32f4xx_hal_rcc.h" +#endif /* HAL_RCC_MODULE_ENABLED */ + +#ifdef HAL_GPIO_MODULE_ENABLED +#include "stm32f4xx_hal_gpio.h" +#endif /* HAL_GPIO_MODULE_ENABLED */ + +#ifdef HAL_EXTI_MODULE_ENABLED +#include "stm32f4xx_hal_exti.h" +#endif /* HAL_EXTI_MODULE_ENABLED */ + +#ifdef HAL_DMA_MODULE_ENABLED +#include "stm32f4xx_hal_dma.h" +#endif /* HAL_DMA_MODULE_ENABLED */ + +#ifdef HAL_CORTEX_MODULE_ENABLED +#include "stm32f4xx_hal_cortex.h" +#endif /* HAL_CORTEX_MODULE_ENABLED */ + +#ifdef HAL_ADC_MODULE_ENABLED +#include "stm32f4xx_hal_adc.h" +#endif /* HAL_ADC_MODULE_ENABLED */ + +#ifdef HAL_CAN_MODULE_ENABLED +#include "stm32f4xx_hal_can.h" +#endif /* HAL_CAN_MODULE_ENABLED */ + +#ifdef HAL_CAN_LEGACY_MODULE_ENABLED +#include "stm32f4xx_hal_can_legacy.h" +#endif /* HAL_CAN_LEGACY_MODULE_ENABLED */ + +#ifdef HAL_CRC_MODULE_ENABLED +#include "stm32f4xx_hal_crc.h" +#endif /* HAL_CRC_MODULE_ENABLED */ + +#ifdef HAL_CRYP_MODULE_ENABLED +#include "stm32f4xx_hal_cryp.h" +#endif /* HAL_CRYP_MODULE_ENABLED */ + +#ifdef HAL_DMA2D_MODULE_ENABLED +#include "stm32f4xx_hal_dma2d.h" +#endif /* HAL_DMA2D_MODULE_ENABLED */ + +#ifdef HAL_DAC_MODULE_ENABLED +#include "stm32f4xx_hal_dac.h" +#endif /* HAL_DAC_MODULE_ENABLED */ + +#ifdef HAL_DCMI_MODULE_ENABLED +#include "stm32f4xx_hal_dcmi.h" +#endif /* HAL_DCMI_MODULE_ENABLED */ + +#ifdef HAL_ETH_MODULE_ENABLED +#include "stm32f4xx_hal_eth.h" +#endif /* HAL_ETH_MODULE_ENABLED */ + +#ifdef HAL_FLASH_MODULE_ENABLED +#include "stm32f4xx_hal_flash.h" +#endif /* HAL_FLASH_MODULE_ENABLED */ + +#ifdef HAL_SRAM_MODULE_ENABLED +#include "stm32f4xx_hal_sram.h" +#endif /* HAL_SRAM_MODULE_ENABLED */ + +#ifdef HAL_NOR_MODULE_ENABLED +#include "stm32f4xx_hal_nor.h" +#endif /* HAL_NOR_MODULE_ENABLED */ + +#ifdef HAL_NAND_MODULE_ENABLED +#include "stm32f4xx_hal_nand.h" +#endif /* HAL_NAND_MODULE_ENABLED */ + +#ifdef HAL_PCCARD_MODULE_ENABLED +#include "stm32f4xx_hal_pccard.h" +#endif /* HAL_PCCARD_MODULE_ENABLED */ + +#ifdef HAL_SDRAM_MODULE_ENABLED +#include "stm32f4xx_hal_sdram.h" +#endif /* HAL_SDRAM_MODULE_ENABLED */ + +#ifdef HAL_HASH_MODULE_ENABLED +#include "stm32f4xx_hal_hash.h" +#endif /* HAL_HASH_MODULE_ENABLED */ + +#ifdef HAL_I2C_MODULE_ENABLED +#include "stm32f4xx_hal_i2c.h" +#endif /* HAL_I2C_MODULE_ENABLED */ + +#ifdef HAL_SMBUS_MODULE_ENABLED +#include "stm32f4xx_hal_smbus.h" +#endif /* HAL_SMBUS_MODULE_ENABLED */ + +#ifdef HAL_I2S_MODULE_ENABLED +#include "stm32f4xx_hal_i2s.h" +#endif /* HAL_I2S_MODULE_ENABLED */ + +#ifdef HAL_IWDG_MODULE_ENABLED +#include "stm32f4xx_hal_iwdg.h" +#endif /* HAL_IWDG_MODULE_ENABLED */ + +#ifdef HAL_LTDC_MODULE_ENABLED +#include "stm32f4xx_hal_ltdc.h" +#endif /* HAL_LTDC_MODULE_ENABLED */ + +#ifdef HAL_PWR_MODULE_ENABLED +#include "stm32f4xx_hal_pwr.h" +#endif /* HAL_PWR_MODULE_ENABLED */ + +#ifdef HAL_RNG_MODULE_ENABLED +#include "stm32f4xx_hal_rng.h" +#endif /* HAL_RNG_MODULE_ENABLED */ + +#ifdef HAL_RTC_MODULE_ENABLED +#include "stm32f4xx_hal_rtc.h" +#endif /* HAL_RTC_MODULE_ENABLED */ + +#ifdef HAL_SAI_MODULE_ENABLED +#include "stm32f4xx_hal_sai.h" +#endif /* HAL_SAI_MODULE_ENABLED */ + +#ifdef HAL_SD_MODULE_ENABLED +#include "stm32f4xx_hal_sd.h" +#endif /* HAL_SD_MODULE_ENABLED */ + +#ifdef HAL_SPI_MODULE_ENABLED +#include "stm32f4xx_hal_spi.h" +#endif /* HAL_SPI_MODULE_ENABLED */ + +#ifdef HAL_TIM_MODULE_ENABLED +#include "stm32f4xx_hal_tim.h" +#endif /* HAL_TIM_MODULE_ENABLED */ + +#ifdef HAL_UART_MODULE_ENABLED +#include "stm32f4xx_hal_uart.h" +#endif /* HAL_UART_MODULE_ENABLED */ + +#ifdef HAL_USART_MODULE_ENABLED +#include "stm32f4xx_hal_usart.h" +#endif /* HAL_USART_MODULE_ENABLED */ + +#ifdef HAL_IRDA_MODULE_ENABLED +#include "stm32f4xx_hal_irda.h" +#endif /* HAL_IRDA_MODULE_ENABLED */ + +#ifdef HAL_SMARTCARD_MODULE_ENABLED +#include "stm32f4xx_hal_smartcard.h" +#endif /* HAL_SMARTCARD_MODULE_ENABLED */ + +#ifdef HAL_WWDG_MODULE_ENABLED +#include "stm32f4xx_hal_wwdg.h" +#endif /* HAL_WWDG_MODULE_ENABLED */ + +#ifdef HAL_PCD_MODULE_ENABLED +#include "stm32f4xx_hal_pcd.h" +#endif /* HAL_PCD_MODULE_ENABLED */ + +#ifdef HAL_HCD_MODULE_ENABLED +#include "stm32f4xx_hal_hcd.h" +#endif /* HAL_HCD_MODULE_ENABLED */ + +#ifdef HAL_DSI_MODULE_ENABLED +#include "stm32f4xx_hal_dsi.h" +#endif /* HAL_DSI_MODULE_ENABLED */ + +#ifdef HAL_QSPI_MODULE_ENABLED +#include "stm32f4xx_hal_qspi.h" +#endif /* HAL_QSPI_MODULE_ENABLED */ + +#ifdef HAL_CEC_MODULE_ENABLED +#include "stm32f4xx_hal_cec.h" +#endif /* HAL_CEC_MODULE_ENABLED */ + +#ifdef HAL_FMPI2C_MODULE_ENABLED +#include "stm32f4xx_hal_fmpi2c.h" +#endif /* HAL_FMPI2C_MODULE_ENABLED */ + +#ifdef HAL_SPDIFRX_MODULE_ENABLED +#include "stm32f4xx_hal_spdifrx.h" +#endif /* HAL_SPDIFRX_MODULE_ENABLED */ + +#ifdef HAL_DFSDM_MODULE_ENABLED +#include "stm32f4xx_hal_dfsdm.h" +#endif /* HAL_DFSDM_MODULE_ENABLED */ + +#ifdef HAL_LPTIM_MODULE_ENABLED +#include "stm32f4xx_hal_lptim.h" +#endif /* HAL_LPTIM_MODULE_ENABLED */ + +#ifdef HAL_MMC_MODULE_ENABLED +#include "stm32f4xx_hal_mmc.h" +#endif /* HAL_MMC_MODULE_ENABLED */ + +/* Exported macro ------------------------------------------------------------*/ +#ifdef USE_FULL_ASSERT +/** + * @brief The assert_param macro is used for function's parameters check. + * @param expr If expr is false, it calls assert_failed function + * which reports the name of the source file and the source + * line number of the call that failed. + * If expr is true, it returns no value. + * @retval None + */ +#define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__)) +/* Exported functions ------------------------------------------------------- */ +void assert_failed(uint8_t *file, uint32_t line); +#else +#define assert_param(expr) ((void)0U) +#endif /* USE_FULL_ASSERT */ + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32F4xx_HAL_CONF_CUSTOM_H */ + + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/buildroot/share/PlatformIO/variants/MARLIN_CREALITY_STM32F401RC/ldscript.ld b/buildroot/share/PlatformIO/variants/MARLIN_CREALITY_STM32F401RC/ldscript.ld new file mode 100644 index 0000000000..004714cd6d --- /dev/null +++ b/buildroot/share/PlatformIO/variants/MARLIN_CREALITY_STM32F401RC/ldscript.ld @@ -0,0 +1,187 @@ +/* +***************************************************************************** +** + +** File : LinkerScript.ld +** +** Abstract : Linker script for STM32F401RETx Device with +** 512KByte FLASH, 96KByte RAM +** +** Set heap size, stack size and stack location according +** to application requirements. +** +** Set memory bank area and size if external memory is used. +** +** Target : STMicroelectronics STM32 +** +** +** Distribution: The file is distributed as is, without any warranty +** of any kind. +** +***************************************************************************** +** @attention +** +**

© COPYRIGHT(c) 2014 Ac6

+** +** Redistribution and use in source and binary forms, with or without modification, +** are permitted provided that the following conditions are met: +** 1. Redistributions of source code must retain the above copyright notice, +** this list of conditions and the following disclaimer. +** 2. Redistributions in binary form must reproduce the above copyright notice, +** this list of conditions and the following disclaimer in the documentation +** and/or other materials provided with the distribution. +** 3. Neither the name of Ac6 nor the names of its contributors +** may be used to endorse or promote products derived from this software +** without specific prior written permission. +** +** THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +** AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE +** IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE +** DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE +** FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL +** DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR +** SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER +** CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, +** OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE +** OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. +** +***************************************************************************** +*/ + +/* Entry Point */ +ENTRY(Reset_Handler) + +/* Highest address of the user mode stack */ +_estack = 0x20010000; /* end of RAM */ + +/* Generate a link error if heap and stack don't fit into RAM */ +_Min_Heap_Size = 0x200;; /* required amount of heap */ +_Min_Stack_Size = 0x400;; /* required amount of stack */ + +/* Specify the memory areas */ +MEMORY +{ +FLASH (rx) : ORIGIN = 0x8000000 + LD_FLASH_OFFSET, LENGTH = LD_MAX_SIZE - LD_FLASH_OFFSET +RAM (xrw) : ORIGIN = 0x20000000, LENGTH = 64K +} + +/* Define output sections */ +SECTIONS +{ + /* The startup code goes first into FLASH */ + .isr_vector : + { + . = ALIGN(4); + KEEP(*(.isr_vector)) /* Startup code */ + . = ALIGN(4); + } >FLASH + + /* The program code and other data goes into FLASH */ + .text ALIGN(4): + { + . = ALIGN(4); + *(.text) /* .text sections (code) */ + *(.text*) /* .text* sections (code) */ + *(.glue_7) /* glue arm to thumb code */ + *(.glue_7t) /* glue thumb to arm code */ + *(.eh_frame) + + KEEP (*(.init)) + KEEP (*(.fini)) + + . = ALIGN(4); + _etext = .; /* define a global symbols at end of code */ + } >FLASH + + /* Constant data goes into FLASH */ + .rodata : + { + . = ALIGN(4); + *(.rodata) /* .rodata sections (constants, strings, etc.) */ + *(.rodata*) /* .rodata* sections (constants, strings, etc.) */ + . = ALIGN(4); + } >FLASH + + .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH + .ARM : { + __exidx_start = .; + *(.ARM.exidx*) + __exidx_end = .; + } >FLASH + + .preinit_array : + { + PROVIDE_HIDDEN (__preinit_array_start = .); + KEEP (*(.preinit_array*)) + PROVIDE_HIDDEN (__preinit_array_end = .); + } >FLASH + .init_array : + { + PROVIDE_HIDDEN (__init_array_start = .); + KEEP (*(SORT(.init_array.*))) + KEEP (*(.init_array*)) + PROVIDE_HIDDEN (__init_array_end = .); + } >FLASH + .fini_array : + { + PROVIDE_HIDDEN (__fini_array_start = .); + KEEP (*(SORT(.fini_array.*))) + KEEP (*(.fini_array*)) + PROVIDE_HIDDEN (__fini_array_end = .); + } >FLASH + + /* used by the startup to initialize data */ + _sidata = LOADADDR(.data); + + /* Initialized data sections goes into RAM, load LMA copy after code */ + .data : + { + . = ALIGN(4); + _sdata = .; /* create a global symbol at data start */ + *(.data) /* .data sections */ + *(.data*) /* .data* sections */ + + . = ALIGN(4); + _edata = .; /* define a global symbol at data end */ + } >RAM AT> FLASH + + + /* Uninitialized data section */ + . = ALIGN(4); + .bss : + { + /* This is used by the startup in order to initialize the .bss secion */ + _sbss = .; /* define a global symbol at bss start */ + __bss_start__ = _sbss; + *(.bss) + *(.bss*) + *(COMMON) + + . = ALIGN(4); + _ebss = .; /* define a global symbol at bss end */ + __bss_end__ = _ebss; + } >RAM + + /* User_heap_stack section, used to check that there is enough RAM left */ + ._user_heap_stack : + { + . = ALIGN(8); + PROVIDE ( end = . ); + PROVIDE ( _end = . ); + . = . + _Min_Heap_Size; + . = . + _Min_Stack_Size; + . = ALIGN(8); + } >RAM + + + + /* Remove information from the standard libraries */ + /DISCARD/ : + { + libc.a ( * ) + libm.a ( * ) + libgcc.a ( * ) + } + + .ARM.attributes 0 : { *(.ARM.attributes) } +} \ No newline at end of file diff --git a/buildroot/share/PlatformIO/variants/MARLIN_CREALITY_STM32F401RC/variant.cpp b/buildroot/share/PlatformIO/variants/MARLIN_CREALITY_STM32F401RC/variant.cpp new file mode 100644 index 0000000000..71f3509ed5 --- /dev/null +++ b/buildroot/share/PlatformIO/variants/MARLIN_CREALITY_STM32F401RC/variant.cpp @@ -0,0 +1,238 @@ +/* + Copyright (c) 2011 Arduino. All right reserved. + + This library is free software; you can redistribute it and/or + modify it under the terms of the GNU Lesser General Public + License as published by the Free Software Foundation; either + version 2.1 of the License, or (at your option) any later version. + + This library is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. + See the GNU Lesser General Public License for more details. + + You should have received a copy of the GNU Lesser General Public + License along with this library; if not, write to the Free Software + Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA +*/ + +#include "pins_arduino.h" + +#ifdef __cplusplus +extern "C" { +#endif + +// Digital PinName array +const PinName digitalPin[] = { + PA_0, // Digital pin 0 + PA_1, // Digital pin 1 + PA_2, // Digital pin 2 + PA_3, // Digital pin 3 + PA_4, // Digital pin 4 + PA_5, // Digital pin 5 + PA_6, // Digital pin 6 + PA_7, // Digital pin 7 + PA_8, // Digital pin 8 + PA_9, // Digital pin 9 + PA_10, // Digital pin 10 + PA_11, // Digital pin 11 + PA_12, // Digital pin 12 + PA_13, // Digital pin 13 + PA_14, // Digital pin 14 + PA_15, // Digital pin 15 + + PB_0, // Digital pin 16 + PB_1, // Digital pin 17 + PB_2, // Digital pin 18 + PB_3, // Digital pin 19 + PB_4, // Digital pin 20 + PB_5, // Digital pin 21 + PB_6, // Digital pin 22 + PB_7, // Digital pin 23 + PB_8, // Digital pin 24 + PB_9, // Digital pin 25 + PB_10, // Digital pin 26 + PB_12, // Digital pin 27 + PB_13, // Digital pin 28 + PB_14, // Digital pin 29 + PB_15, // Digital pin 30 + + PC_0, // Digital pin 31 + PC_1, // Digital pin 32 + PC_2, // Digital pin 33 + PC_3, // Digital pin 34 + PC_4, // Digital pin 35 + PC_5, // Digital pin 36 + PC_6, // Digital pin 37 + PC_7, // Digital pin 38 + PC_8, // Digital pin 39 + PC_9, // Digital pin 40 + PC_10, // Digital pin 41 + PC_11, // Digital pin 42 + PC_12, // Digital pin 43 + PC_13, // Digital pin 44 + PC_14, // Digital pin 45 + PC_15, // Digital pin 46 + + PD_2, // Digital pin 47 + + PH_0, // Digital pin 48, used by the external oscillator + PH_1 // Digital pin 49, used by the external oscillator +}; + +// Analog (Ax) pin number array +const uint32_t analogInputPin[] = { + 0, // A0, PA0 + 1, // A1, PA1 + 2, // A2, PA2 + 3, // A3, PA3 + 4, // A4, PA4 + 5, // A5, PA5 + 6, // A6, PA6 + 7, // A7, PA7 + 16, // A8, PB0 + 17, // A9, PB1 + 31, // A10, PC0 + 32, // A11, PC1 + 33, // A12, PC2 + 34, // A13, PC3 + 35, // A14, PC4 + 36 // A15, PC5 +}; + +#ifdef __cplusplus +} +#endif + +// ---------------------------------------------------------------------------- + +#ifdef __cplusplus +extern "C" { +#endif + +/* + * @brief Configures the System clock source, PLL Multiplier and Divider factors, + * AHB/APBx prescalers and Flash settings + * @note This function should be called only once the RCC clock configuration + * is reset to the default reset state (done in SystemInit() function). + * @param None + * @retval None + */ + +/******************************************************************************/ +/* PLL (clocked by HSE) used as System clock source */ +/******************************************************************************/ +static uint8_t SetSysClock_PLL_HSE(uint8_t bypass) +{ + RCC_OscInitTypeDef RCC_OscInitStruct; + RCC_ClkInitTypeDef RCC_ClkInitStruct; + + /* The voltage scaling allows optimizing the power consumption when the device is + clocked below the maximum system frequency, to update the voltage scaling value + regarding system frequency refer to product datasheet. */ + __HAL_RCC_PWR_CLK_ENABLE(); + __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2); + + // Enable HSE oscillator and activate PLL with HSE as source + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; + if (bypass == 0) { + RCC_OscInitStruct.HSEState = RCC_HSE_ON; // External 8 MHz xtal on OSC_IN/OSC_OUT + } else { + RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; // External 8 MHz clock on OSC_IN + } + + RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; + RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; + RCC_OscInitStruct.PLL.PLLM = HSE_VALUE / 1000000L; // Expects an 8 MHz external clock by default. Redefine HSE_VALUE if not + RCC_OscInitStruct.PLL.PLLN = 336; // VCO output clock = 336 MHz (1 MHz * 336) + RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4; // PLLCLK = 84 MHz (336 MHz / 4) + RCC_OscInitStruct.PLL.PLLQ = 7; // USB clock = 48 MHz (336 MHz / 7) --> OK for USB + if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) { + return 0; // FAIL + } + + // Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers + RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2; + RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 84 MHz + RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 84 MHz + RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2; // 42 MHz + RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; // 84 MHz + if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK) { + return 0; // FAIL + } + + /* Output clock on MCO1 pin(PA8) for debugging purpose */ + /* + if (bypass == 0) + HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_2); // 4 MHz + else + HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1); // 8 MHz + */ + + return 1; // OK +} + +/******************************************************************************/ +/* PLL (clocked by HSI) used as System clock source */ +/******************************************************************************/ +uint8_t SetSysClock_PLL_HSI(void) +{ + RCC_OscInitTypeDef RCC_OscInitStruct; + RCC_ClkInitTypeDef RCC_ClkInitStruct; + + /* The voltage scaling allows optimizing the power consumption when the device is + clocked below the maximum system frequency, to update the voltage scaling value + regarding system frequency refer to product datasheet. */ + __HAL_RCC_PWR_CLK_ENABLE(); + __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE2); + + // Enable HSI oscillator and activate PLL with HSI as source + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE; + RCC_OscInitStruct.HSIState = RCC_HSI_ON; + RCC_OscInitStruct.HSEState = RCC_HSE_OFF; + RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT; + RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; + RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI; + RCC_OscInitStruct.PLL.PLLM = 16; // VCO input clock = 1 MHz (16 MHz / 16) + RCC_OscInitStruct.PLL.PLLN = 336; // VCO output clock = 336 MHz (1 MHz * 336) + RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4; // PLLCLK = 84 MHz (336 MHz / 4) + RCC_OscInitStruct.PLL.PLLQ = 7; // USB clock = 48 MHz (336 MHz / 7) --> freq is ok but not precise enough + if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) { + return 0; // FAIL + } + + /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */ + RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2); + RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; // 84 MHz + RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 84 MHz + RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2; // 42 MHz + RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; // 84 MHz + if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK) { + return 0; // FAIL + } + + /* Output clock on MCO1 pin(PA8) for debugging purpose */ + //HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSI, RCC_MCODIV_1); // 16 MHz + + return 1; // OK +} + +WEAK void SystemClock_Config(void) +{ + /* 1- If fail try to start with HSE and external xtal */ + if (SetSysClock_PLL_HSE(0) == 0) { + /* 2- Try to start with HSE and external clock */ + if (SetSysClock_PLL_HSE(1) == 0) { + /* 3- If fail start with HSI clock */ + if (SetSysClock_PLL_HSI() == 0) { + Error_Handler(); + } + } + } + /* Output clock on MCO2 pin(PC9) for debugging purpose */ + //HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_4); +} + +#ifdef __cplusplus +} +#endif \ No newline at end of file diff --git a/buildroot/share/PlatformIO/variants/MARLIN_CREALITY_STM32F401RC/variant.h b/buildroot/share/PlatformIO/variants/MARLIN_CREALITY_STM32F401RC/variant.h new file mode 100644 index 0000000000..b5a4e5ef80 --- /dev/null +++ b/buildroot/share/PlatformIO/variants/MARLIN_CREALITY_STM32F401RC/variant.h @@ -0,0 +1,151 @@ +/* + Copyright (c) 2011 Arduino. All right reserved. + + This library is free software; you can redistribute it and/or + modify it under the terms of the GNU Lesser General Public + License as published by the Free Software Foundation; either + version 2.1 of the License, or (at your option) any later version. + + This library is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. + See the GNU Lesser General Public License for more details. + + You should have received a copy of the GNU Lesser General Public + License along with this library; if not, write to the Free Software + Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA +*/ + +#ifndef _VARIANT_ARDUINO_STM32_ +#define _VARIANT_ARDUINO_STM32_ + +#ifdef __cplusplus +extern "C" { +#endif // __cplusplus + + +// | DIGITAL | ANALOG | USART | TWI | SPI | SPECIAL | +// |---------|--------|-----------|----------|------------------------|-----------| +#define PA0 0 // | 0 | A0 | | | | | +#define PA1 1 // | 1 | A1 | | | | | +#define PA2 2 // | 2 | A2 | USART2_TX | | | | +#define PA3 3 // | 3 | A3 | USART2_RX | | | | +#define PA4 4 // | 4 | A4 | | | SPI1_SS, (SPI3_SS) | | +#define PA5 5 // | 5 | A5 | | | SPI1_SCK | | +#define PA6 6 // | 6 | A6 | | | SPI1_MISO | | +#define PA7 7 // | 7 | A7 | | | SPI1_MOSI | | +#define PA8 8 // | 8 | | | TWI3_SCL | | | +#define PA9 9 // | 9 | | USART1_TX | | | | +#define PA10 10 // | 10 | | USART1_RX | | | | +#define PA11 11 // | 11 | | USART6_TX | | | | +#define PA12 12 // | 12 | | USART6_RX | | | | +#define PA13 13 // | 13 | | | | | SWD_SWDIO | +#define PA14 14 // | 14 | | | | | SWD_SWCLK | +#define PA15 15 // | 15 | | | | SPI3_SS, (SPI1_SS) | | +// |---------|--------|-----------|----------|------------------------|-----------| +#define PB0 16 // | 16 | A8 | | | | | +#define PB1 17 // | 17 | A9 | | | | | +#define PB2 18 // | 18 | | | | | BOOT1 | +#define PB3 19 // | 19 | | | TWI2_SDA | SPI3_SCK, (SPI1_SCK) | | +#define PB4 20 // | 20 | | | TWI3_SDA | SPI3_MISO, (SPI1_MISO) | | +#define PB5 21 // | 21 | | | | SPI3_MOSI, (SPI1_MOSI) | | +#define PB6 22 // | 22 | | USART1_TX | TWI1_SCL | | | +#define PB7 23 // | 23 | | USART1_RX | TWI1_SDA | | | +#define PB8 24 // | 24 | | | TWI1_SCL | | | +#define PB9 25 // | 25 | | | TWI1_SDA | SPI2_SS | | +#define PB10 26 // | 26 | | | TWI2_SCL | SPI2_SCK | | +#define PB12 27 // | 27 | | | | SPI2_SS | | +#define PB13 28 // | 28 | | | | SPI2_SCK | | +#define PB14 29 // | 29 | | | | SPI2_MISO | | +#define PB15 30 // | 30 | | | | SPI2_MOSI | | +// |---------|--------|-----------|----------|------------------------|-----------| +#define PC0 31 // | 31 | A10 | | | | | +#define PC1 32 // | 32 | A11 | | | | | +#define PC2 33 // | 33 | A12 | | | SPI2_MISO | | +#define PC3 34 // | 34 | A13 | | | SPI2_MOSI | | +#define PC4 35 // | 35 | A14 | | | | | +#define PC5 36 // | 36 | A15 | | | | | +#define PC6 37 // | 37 | | USART6_TX | | | | +#define PC7 38 // | 38 | | USART6_RX | | | | +#define PC8 39 // | 39 | | | | | | +#define PC9 40 // | 40 | | | TWI3_SDA | | | +#define PC10 41 // | 41 | | | | SPI3_SCK | | +#define PC11 42 // | 42 | | | | SPI3_MISO | | +#define PC12 43 // | 43 | | | | SPI3_MOSI | | +#define PC13 44 // | 44 | | | | | | +#define PC14 45 // | 45 | | | | | OSC32_IN | +#define PC15 46 // | 46 | | | | | OSC32_OUT | +// |---------|--------|-----------|----------|------------------------|-----------| +#define PD2 47 // | 47 | | | | | | +// |---------|--------|-----------|----------|------------------------|-----------| +#define PH0 48 // | 48 | | | | | OSC_IN | +#define PH1 49 // | 49 | | | | | OSC_OUT | +// |---------|--------|-----------|----------|------------------------|-----------| + +// This must be a literal +#define NUM_DIGITAL_PINS 50 +#define NUM_ANALOG_INPUTS 16 + +// SPI definitions +#define PIN_SPI_SS PA4 +#define PIN_SPI_SS1 PA4 +#define PIN_SPI_MOSI PA7 +#define PIN_SPI_MISO PA6 +#define PIN_SPI_SCK PA5 + + +// Timer Definitions +#define TIMER_TONE TIM2 +#define TIMER_SERVO TIM5 +#define TIMER_SERIAL TIM11 + +// UART Definitions +//#define ENABLE_HWSERIAL1 done automatically by the #define SERIAL_UART_INSTANCE below +#define ENABLE_HWSERIAL2 + + +// Define here Serial instance number to map on Serial generic name (if not already used by SerialUSB) +#define SERIAL_UART_INSTANCE 1 //1 for Serial = Serial1 (USART1) + +// Default pin used for 'Serial' instance +// Mandatory for Firmata +#define PIN_SERIAL_RX PA10 +#define PIN_SERIAL_TX PA9 + +// Used when user instanciate a hardware Serial using its peripheral name. +// Example: HardwareSerial mySerial(USART3); +// will use PIN_SERIAL3_RX and PIN_SERIAL3_TX if defined. +#define PIN_SERIAL1_RX PA10 +#define PIN_SERIAL1_TX PA9 +#define PIN_SERIAL2_RX PA3 +#define PIN_SERIAL2_TX PA2 + +#ifdef __cplusplus +} // extern "C" +#endif +/*---------------------------------------------------------------------------- + * Arduino objects - C++ only + *----------------------------------------------------------------------------*/ + +#ifdef __cplusplus + // These serial port names are intended to allow libraries and architecture-neutral + // sketches to automatically default to the correct port name for a particular type + // of use. For example, a GPS module would normally connect to SERIAL_PORT_HARDWARE_OPEN, + // the first hardware serial port whose RX/TX pins are not dedicated to another use. + // + // SERIAL_PORT_MONITOR Port which normally prints to the Arduino Serial Monitor + // + // SERIAL_PORT_USBVIRTUAL Port which is USB virtual serial + // + // SERIAL_PORT_LINUXBRIDGE Port which connects to a Linux system via Bridge library + // + // SERIAL_PORT_HARDWARE Hardware serial port, physical RX & TX pins. + // + // SERIAL_PORT_HARDWARE_OPEN Hardware serial ports which are open for use. Their RX & TX + // pins are NOT connected to anything by default. + #define SERIAL_PORT_MONITOR Serial + #define SERIAL_PORT_HARDWARE Serial1 + #define SERIAL_PORT_HARDWARE_OPEN Serial2 +#endif + +#endif /* _VARIANT_ARDUINO_STM32_ */ \ No newline at end of file diff --git a/buildroot/tests/STM32F103RE_creality b/buildroot/tests/STM32F103RE_creality index 6440c56792..a5d2899dd5 100755 --- a/buildroot/tests/STM32F103RE_creality +++ b/buildroot/tests/STM32F103RE_creality @@ -13,12 +13,6 @@ use_example_configs "Creality/Ender-3 V2/CrealityV422/CrealityUI" opt_enable MARLIN_DEV_MODE BUFFER_MONITORING BLTOUCH AUTO_BED_LEVELING_BILINEAR Z_SAFE_HOMING exec_test $1 $2 "Ender 3 v2 with CrealityUI" "$3" -use_example_configs "Creality/Ender-3 V2/CrealityV422/CrealityUI" -opt_disable DWIN_CREALITY_LCD -opt_enable BLTOUCH AUTO_BED_LEVELING_UBL Z_SAFE_HOMING INDIVIDUAL_AXIS_HOMING_SUBMENU LCD_SET_PROGRESS_MANUALLY STATUS_MESSAGE_SCROLLING BAUD_RATE_GCODE \ - DWIN_LCD_PROUI SOUND_MENU_ITEM PRINTCOUNTER -exec_test $1 $2 "Ender 3 v2 with ProUI" "$3" - use_example_configs "Creality/Ender-3 V2/CrealityV422/CrealityUI" opt_disable DWIN_CREALITY_LCD opt_enable DWIN_CREALITY_LCD_JYERSUI AUTO_BED_LEVELING_BILINEAR PROBE_MANUALLY diff --git a/buildroot/tests/STM32F401RC_creality b/buildroot/tests/STM32F401RC_creality new file mode 100755 index 0000000000..c7cd464df0 --- /dev/null +++ b/buildroot/tests/STM32F401RC_creality @@ -0,0 +1,20 @@ +#!/usr/bin/env bash +# +# Build tests for STM32F401RC_creality +# + +# exit on first failure +set -e + +use_example_configs "Creality/Ender-3 S1" +opt_disable DWIN_CREALITY_LCD Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN AUTO_BED_LEVELING_BILINEAR CONFIGURATION_EMBEDDING CANCEL_OBJECTS FWRETRACT +opt_enable DWIN_LCD_PROUI INDIVIDUAL_AXIS_HOMING_SUBMENU LCD_SET_PROGRESS_MANUALLY STATUS_MESSAGE_SCROLLING \ + SOUND_MENU_ITEM PRINTCOUNTER NOZZLE_PARK_FEATURE ADVANCED_PAUSE_FEATURE FILAMENT_RUNOUT_SENSOR \ + BLTOUCH Z_SAFE_HOMING AUTO_BED_LEVELING_UBL MESH_EDIT_MENU \ + LIMITED_MAX_FR_EDITING LIMITED_MAX_ACCEL_EDITING LIMITED_JERK_EDITING BAUD_RATE_GCODE +opt_set MOTHERBOARD BOARD_CREALITY_V24S1_301F4 \ + PREHEAT_3_LABEL '"CUSTOM"' PREHEAT_3_TEMP_HOTEND 240 PREHEAT_3_TEMP_BED 60 PREHEAT_3_FAN_SPEED 128 +exec_test $1 $2 "Ender-3 S1 with ProUI" "$3" + +# clean up +restore_configs diff --git a/ini/stm32f1-maple.ini b/ini/stm32f1-maple.ini index 9ea848f1b6..e54207168e 100644 --- a/ini/stm32f1-maple.ini +++ b/ini/stm32f1-maple.ini @@ -147,6 +147,20 @@ extra_scripts = ${common_stm32f1.extra_scripts} debug_tool = jlink upload_protocol = jlink +# +# Creality (STM32F103RET6) +# +[env:STM32F103RE_creality_smartPro_maple] +extends = env:STM32F103RE_maple +build_flags = ${common_stm32f1.build_flags} -DTEMP_TIMER_CHAN=4 +board_build.address = 0x08010000 +board_build.ldscript = crealityPro.ld +extra_scripts = ${common_stm32f1.extra_scripts} + pre:buildroot/share/PlatformIO/scripts/random-bin.py + buildroot/share/PlatformIO/scripts/custom_board.py +debug_tool = jlink +upload_protocol = jlink + # # BigTree SKR Mini E3 V2.0 & DIP / SKR CR6 (STM32F103RET6 ARM Cortex-M3) # diff --git a/ini/stm32f1.ini b/ini/stm32f1.ini index 9002f81a81..43c0526d2a 100644 --- a/ini/stm32f1.ini +++ b/ini/stm32f1.ini @@ -164,6 +164,23 @@ board = genericSTM32F103RC extends = STM32F103Rx_creality_xfer board = genericSTM32F103RC +[STM32F103RE_creality_SmartPro] +extends = stm32_variant +board_build.variant = MARLIN_F103Rx +board_build.offset = 0x10000 +board_upload.offset_address = 0x08010000 +build_flags = ${stm32_variant.build_flags} + -DMCU_STM32F103RE -DHAL_SD_MODULE_ENABLED + -DSS_TIMER=4 -DTIMER_SERVO=TIM5 + -DENABLE_HWSERIAL3 -DTRANSFER_CLOCK_DIV=8 +build_unflags = ${stm32_variant.build_unflags} + -DUSBCON -DUSBD_USE_CDC +extra_scripts = ${stm32_variant.extra_scripts} + pre:buildroot/share/PlatformIO/scripts/random-bin.py +monitor_speed = 115200 +debug_tool = stlink +upload_protocol = stlink + # # BigTree SKR Mini E3 V2.0 & DIP / SKR CR6 (STM32F103RET6 ARM Cortex-M3) # diff --git a/ini/stm32f4.ini b/ini/stm32f4.ini index d7c160d639..ff9977670c 100644 --- a/ini/stm32f4.ini +++ b/ini/stm32f4.ini @@ -598,4 +598,31 @@ build_flags = ${common_stm32.build_flags} -DUSB_PRODUCT=\"Artillery_3D_Printer\" -DFLASH_DATA_SECTOR=1U -DFLASH_BASE_ADDRESS=0x08004000 extra_scripts = ${common_stm32.extra_scripts} - pre:buildroot/share/PlatformIO/scripts/generic_create_variant.py + pre:buildroot/share/PlatformIO/scripts/generic_create_variant.py + +# +# Ender-3 S1 STM32F401RC_creality +# +[env:STM32F401RC_creality] +extends = stm32_variant +board = genericSTM32F401RC +board_build.variant = MARLIN_CREALITY_STM32F401RC +board_build.offset = 0x10000 +board_upload.offset_address = 0x08010000 +build_flags = ${stm32_variant.build_flags} -DMCU_STM32F401RC -DSTM32F4 + -DSS_TIMER=4 -DTIMER_SERVO=TIM5 + -DENABLE_HWSERIAL3 -DTRANSFER_CLOCK_DIV=8 +build_unflags = ${stm32_variant.build_unflags} -DUSBCON -DUSBD_USE_CDC +extra_scripts = ${stm32_variant.extra_scripts} + pre:buildroot/share/PlatformIO/scripts/random-bin.py +monitor_speed = 115200 + +[env:STM32F401RC_creality_jlink] +extends = env:STM32F401RC_creality +debug_tool = jlink +upload_protocol = jlink + +[env:STM32F401RC_creality_stlink] +extends = env:STM32F401RC_creality +debug_tool = stlink +upload_protocol = stlink