From 192cc1d9d748658e65d9e5cf6cc70c426b897546 Mon Sep 17 00:00:00 2001 From: InsanityAutomation Date: Fri, 2 Aug 2019 21:54:15 -0400 Subject: [PATCH] Bump --- Marlin/Configuration.h | 136 +- Marlin/Configuration_adv.h | 48 +- .../{HAL_STM32F7/watchdog_STM32F7.h => HAL.h} | 5 +- Marlin/src/HAL/HAL_AVR/HAL.cpp | 57 +- Marlin/src/HAL/HAL_AVR/HAL.h | 24 +- Marlin/src/HAL/HAL_AVR/HAL_spi_AVR.cpp | 14 +- Marlin/src/HAL/HAL_AVR/MarlinSerial.h | 1 - Marlin/src/HAL/HAL_AVR/ServoTimers.h | 4 +- Marlin/src/HAL/HAL_AVR/endstop_interrupts.h | 1 - .../HAL/HAL_AVR/{ => fastio}/fastio_1280.h | 2 +- .../HAL/HAL_AVR/{ => fastio}/fastio_1281.h | 2 +- .../src/HAL/HAL_AVR/{ => fastio}/fastio_168.h | 2 +- .../src/HAL/HAL_AVR/{ => fastio}/fastio_644.h | 2 +- .../HAL/HAL_AVR/{ => fastio}/fastio_AT90USB.h | 2 +- Marlin/src/HAL/HAL_AVR/fastio_AVR.h | 16 +- Marlin/src/HAL/HAL_AVR/inc/Conditionals_LCD.h | 22 + Marlin/src/HAL/HAL_AVR/inc/Conditionals_adv.h | 22 + .../src/HAL/HAL_AVR/inc/Conditionals_post.h | 22 + .../src/HAL/HAL_AVR/{ => inc}/SanityCheck.h | 0 Marlin/src/HAL/HAL_AVR/pinsDebug.h | 4 +- Marlin/src/HAL/HAL_AVR/pinsDebug_plus_70.h | 6 +- .../src/HAL/HAL_DUE/EepromEmulation_Due.cpp | 4 +- Marlin/src/HAL/HAL_DUE/HAL.cpp | 44 +- Marlin/src/HAL/HAL_DUE/HAL.h | 4 - Marlin/src/HAL/HAL_DUE/HAL_spi_Due.cpp | 23 +- Marlin/src/HAL/HAL_DUE/HAL_timers_Due.cpp | 37 +- Marlin/src/HAL/HAL_DUE/HAL_timers_Due.h | 20 +- Marlin/src/HAL/HAL_DUE/ServoTimers.h | 4 +- Marlin/src/HAL/HAL_DUE/Servo_Due.cpp | 6 +- Marlin/src/HAL/HAL_DUE/Tone.cpp | 2 + .../u8g_com_HAL_DUE_shared_hw_spi.cpp | 75 +- .../u8g_com_HAL_DUE_st7920_sw_spi.cpp | 8 +- .../{ => dogm}/u8g_com_HAL_DUE_sw_spi.cpp | 6 +- .../u8g_com_HAL_DUE_sw_spi_shared.cpp | 4 +- .../u8g_com_HAL_DUE_sw_spi_shared.h | 4 +- .../src/HAL/HAL_DUE/{ => fastio}/G2_PWM.cpp | 2 +- Marlin/src/HAL/HAL_DUE/{ => fastio}/G2_PWM.h | 4 +- Marlin/src/HAL/HAL_DUE/{ => fastio}/G2_pins.h | 0 Marlin/src/HAL/HAL_DUE/fastio_Due.h | 4 +- Marlin/src/HAL/HAL_DUE/inc/Conditionals_LCD.h | 22 + Marlin/src/HAL/HAL_DUE/inc/Conditionals_adv.h | 22 + .../src/HAL/HAL_DUE/inc/Conditionals_post.h | 22 + .../src/HAL/HAL_DUE/{ => inc}/SanityCheck.h | 0 .../HAL/HAL_DUE/persistent_store_eeprom.cpp | 4 +- Marlin/src/HAL/HAL_DUE/pinsDebug.h | 5 +- Marlin/src/HAL/HAL_DUE/usb/udi_cdc.c | 6 +- Marlin/src/HAL/HAL_DUE/usb/udi_msc.c | 10 +- .../src/HAL/HAL_DUE/usb/uotghs_device_due.c | 9 +- .../src/HAL/HAL_DUE/usb/uotghs_device_due.h | 2 +- Marlin/src/HAL/HAL_ESP32/HAL.cpp | 168 +- Marlin/src/HAL/HAL_ESP32/HAL.h | 20 +- Marlin/src/HAL/HAL_ESP32/HAL_Servo_ESP32.cpp | 4 +- Marlin/src/HAL/HAL_ESP32/HAL_spi_ESP32.cpp | 20 +- Marlin/src/HAL/HAL_ESP32/HAL_timers_ESP32.cpp | 62 +- Marlin/src/HAL/HAL_ESP32/HAL_timers_ESP32.h | 32 +- Marlin/src/HAL/HAL_ESP32/fastio_ESP32.h | 2 +- Marlin/src/HAL/HAL_ESP32/i2s.cpp | 23 +- .../src/HAL/HAL_ESP32/inc/Conditionals_LCD.h | 22 + .../src/HAL/HAL_ESP32/inc/Conditionals_adv.h | 22 + .../src/HAL/HAL_ESP32/inc/Conditionals_post.h | 22 + .../src/HAL/HAL_ESP32/{ => inc}/SanityCheck.h | 0 Marlin/src/HAL/HAL_LINUX/HAL.cpp | 4 +- Marlin/src/HAL/HAL_LINUX/HAL.h | 4 - Marlin/src/HAL/HAL_LINUX/HAL_timers.h | 8 +- .../src/HAL/HAL_LINUX/inc/Conditionals_LCD.h | 22 + .../src/HAL/HAL_LINUX/inc/Conditionals_adv.h | 22 + .../src/HAL/HAL_LINUX/inc/Conditionals_post.h | 22 + .../src/HAL/HAL_LINUX/{ => inc}/SanityCheck.h | 0 Marlin/src/HAL/HAL_LINUX/include/Arduino.h | 2 - Marlin/src/HAL/HAL_LINUX/include/serial.h | 5 +- Marlin/src/HAL/HAL_LINUX/main.cpp | 2 +- .../HAL/HAL_LINUX/persistent_store_impl.cpp | 9 +- Marlin/src/HAL/HAL_LINUX/pinsDebug.h | 5 +- Marlin/src/HAL/HAL_LINUX/spi_pins.h | 4 +- Marlin/src/HAL/HAL_LPC1768/HAL.h | 8 +- Marlin/src/HAL/HAL_LPC1768/HAL_spi.cpp | 10 +- Marlin/src/HAL/HAL_LPC1768/HAL_timers.h | 12 +- Marlin/src/HAL/HAL_LPC1768/MarlinSerial.h | 2 + .../HAL/HAL_LPC1768/inc/Conditionals_LCD.h | 22 + .../HAL/HAL_LPC1768/inc/Conditionals_adv.h | 22 + .../HAL/HAL_LPC1768/inc/Conditionals_post.h | 22 + .../HAL/HAL_LPC1768/{ => inc}/SanityCheck.h | 0 Marlin/src/HAL/HAL_LPC1768/main.cpp | 41 +- .../HAL_LPC1768/persistent_store_sdcard.cpp | 2 +- Marlin/src/HAL/HAL_LPC1768/pinsDebug.h | 5 +- Marlin/src/HAL/HAL_LPC1768/spi_pins.h | 2 +- Marlin/src/HAL/HAL_SAMD51/HAL.cpp | 475 +++ Marlin/src/HAL/HAL_SAMD51/HAL.h | 142 + Marlin/src/HAL/HAL_SAMD51/HAL_spi_SAMD51.cpp | 151 + .../src/HAL/HAL_SAMD51/HAL_timers_SAMD51.cpp | 135 + Marlin/src/HAL/HAL_SAMD51/HAL_timers_SAMD51.h | 116 + .../src/HAL/HAL_SAMD51/MarlinSerial_AGCM4.cpp | 55 + .../MarlinSerial_AGCM4.h} | 12 +- Marlin/src/HAL/HAL_SAMD51/SAMD51.h | 70 + Marlin/src/HAL/HAL_SAMD51/ServoTimers.h | 39 + Marlin/src/HAL/HAL_SAMD51/Servo_SAMD51.cpp | 226 ++ .../src/HAL/HAL_SAMD51/endstop_interrupts.h | 184 ++ Marlin/src/HAL/HAL_SAMD51/fastio_SAMD51.h | 251 ++ .../src/HAL/HAL_SAMD51/inc/Conditionals_LCD.h | 22 + .../src/HAL/HAL_SAMD51/inc/Conditionals_adv.h | 22 + .../HAL/HAL_SAMD51/inc/Conditionals_post.h | 22 + Marlin/src/HAL/HAL_SAMD51/inc/SanityCheck.h | 48 + .../HAL_SAMD51/persistent_store_eeprom.cpp | 129 + Marlin/src/HAL/HAL_SAMD51/pinsDebug.h | 153 + Marlin/src/HAL/HAL_SAMD51/spi_pins.h | 54 + Marlin/src/HAL/HAL_SAMD51/watchdog_SAMD51.cpp | 53 + Marlin/src/HAL/HAL_SAMD51/watchdog_SAMD51.h | 31 + Marlin/src/HAL/HAL_STM32/HAL.cpp | 47 +- Marlin/src/HAL/HAL_STM32/HAL.h | 22 +- Marlin/src/HAL/HAL_STM32/HAL_spi_STM32.cpp | 20 +- Marlin/src/HAL/HAL_STM32/HAL_timers_STM32.cpp | 41 +- Marlin/src/HAL/HAL_STM32/HAL_timers_STM32.h | 24 +- Marlin/src/HAL/HAL_STM32/fastio_STM32.h | 14 +- .../src/HAL/HAL_STM32/inc/Conditionals_LCD.h | 22 + .../src/HAL/HAL_STM32/inc/Conditionals_adv.h | 22 + .../src/HAL/HAL_STM32/inc/Conditionals_post.h | 22 + .../src/HAL/HAL_STM32/{ => inc}/SanityCheck.h | 0 .../HAL/HAL_STM32/persistent_store_impl.cpp | 32 +- .../HAL/HAL_STM32/persistent_store_sdcard.cpp | 104 + Marlin/src/HAL/HAL_STM32/pinsDebug.h | 35 +- .../HAL/HAL_STM32/pinsDebug_STM32GENERIC.h | 123 + .../src/HAL/HAL_STM32/pinsDebug_STM32duino.h | 275 ++ Marlin/src/HAL/HAL_STM32/pins_Xref.h | 612 ++++ Marlin/src/HAL/HAL_STM32/watchdog_STM32.cpp | 6 +- Marlin/src/HAL/HAL_STM32F1/HAL.cpp | 59 +- Marlin/src/HAL/HAL_STM32F1/HAL.h | 24 +- .../src/HAL/HAL_STM32F1/HAL_sdio_STM32F1.cpp | 8 +- Marlin/src/HAL/HAL_STM32F1/HAL_sdio_STM32F1.h | 20 +- .../src/HAL/HAL_STM32F1/HAL_spi_Stm32f1.cpp | 37 +- .../HAL/HAL_STM32F1/HAL_timers_Stm32f1.cpp | 42 +- .../src/HAL/HAL_STM32F1/HAL_timers_Stm32f1.h | 29 +- .../{ => dogm}/u8g_com_stm32duino_fsmc.cpp | 95 +- .../{ => dogm}/u8g_com_stm32duino_swspi.cpp | 4 +- Marlin/src/HAL/HAL_STM32F1/fastio_Stm32f1.h | 127 + .../HAL/HAL_STM32F1/inc/Conditionals_LCD.h | 22 + .../HAL/HAL_STM32F1/inc/Conditionals_adv.h | 22 + .../HAL/HAL_STM32F1/inc/Conditionals_post.h | 22 + .../HAL/HAL_STM32F1/{ => inc}/SanityCheck.h | 0 .../HAL_STM32F1/persistent_store_eeprom.cpp | 4 +- .../HAL_STM32F1/persistent_store_flash.cpp | 2 +- .../HAL_STM32F1/persistent_store_sdcard.cpp | 28 +- Marlin/src/HAL/HAL_STM32F1/pinsDebug.h | 114 +- .../HAL/HAL_STM32F1/stm32f1_flag_script.py | 1 - .../src/HAL/HAL_STM32F1/watchdog_Stm32f1.cpp | 1 - .../HAL_STM32F4/EEPROM_Emul/eeprom_emul.cpp | 569 ---- Marlin/src/HAL/HAL_STM32F4/EmulatedEeprom.cpp | 142 - Marlin/src/HAL/HAL_STM32F4/HAL.cpp | 133 - Marlin/src/HAL/HAL_STM32F4/HAL.h | 236 -- .../src/HAL/HAL_STM32F4/HAL_Servo_STM32F4.cpp | 53 - Marlin/src/HAL/HAL_STM32F4/fastio_STM32F4.h | 153 - .../HAL_STM32F4/persistent_store_eeprom.cpp | 69 - Marlin/src/HAL/HAL_STM32F4/pinsDebug.h | 1 - .../HAL/HAL_STM32F7/EEPROM_Emul/eeprom_emul.h | 111 - Marlin/src/HAL/HAL_STM32F7/EmulatedEeprom.cpp | 139 - Marlin/src/HAL/HAL_STM32F7/HAL.cpp | 139 - .../src/HAL/HAL_STM32F7/HAL_spi_STM32F7.cpp | 164 -- .../src/HAL/HAL_STM32F7/endstop_interrupts.h | 64 - Marlin/src/HAL/HAL_STM32F7/pinsDebug.h | 1 - .../src/HAL/HAL_STM32F7/watchdog_STM32F7.cpp | 52 - .../HAL/HAL_STM32_F4_F7/EmulatedEeprom.cpp | 122 + Marlin/src/HAL/HAL_STM32_F4_F7/HAL.cpp | 96 + .../{HAL_STM32F7 => HAL_STM32_F4_F7}/HAL.h | 68 +- .../HAL_Servo_STM32_F4_F7.cpp} | 8 +- .../HAL_Servo_STM32_F4_F7.h} | 9 +- .../HAL_spi_STM32_F4_F7.cpp} | 35 +- .../HAL_STM32_F4_F7/HAL_timers_STM32_F4_F7.h | 28 + Marlin/src/HAL/HAL_STM32_F4_F7/README.md | 6 + .../STM32F4}/HAL_timers_STM32F4.cpp | 42 +- .../STM32F4}/HAL_timers_STM32F4.h | 26 +- .../STM32F4}/README.md | 0 .../STM32F7}/HAL_timers_STM32F7.cpp | 46 +- .../STM32F7}/HAL_timers_STM32F7.h | 22 +- .../STM32F7}/README.md | 7 +- .../STM32F7}/TMC2660.cpp | 32 +- .../STM32F7}/TMC2660.h | 1 - .../eeprom_emul.cpp | 200 +- .../eeprom_emul.h | 67 +- .../endstop_interrupts.h | 0 .../fastio_STM32_F4_F7.h} | 76 +- .../HAL_STM32_F4_F7/inc/Conditionals_LCD.h | 22 + .../HAL_STM32_F4_F7/inc/Conditionals_adv.h | 22 + .../HAL_STM32_F4_F7/inc/Conditionals_post.h | 22 + .../inc}/SanityCheck.h | 4 +- .../persistent_store_eeprom.cpp | 8 +- Marlin/src/HAL/HAL_STM32_F4_F7/pinsDebug.h | 27 + .../spi_pins.h | 0 .../watchdog_STM32_F4_F7.cpp} | 17 +- .../watchdog_STM32_F4_F7.h} | 0 Marlin/src/HAL/HAL_TEENSY31_32/HAL.h | 8 +- .../HAL/HAL_TEENSY31_32/HAL_timers_Teensy.h | 14 +- .../HAL/HAL_TEENSY31_32/endstop_interrupts.h | 2 - .../src/HAL/HAL_TEENSY31_32/fastio_Teensy.h | 2 - .../HAL_TEENSY31_32/inc/Conditionals_LCD.h | 22 + .../HAL_TEENSY31_32/inc/Conditionals_adv.h | 22 + .../HAL_TEENSY31_32/inc/Conditionals_post.h | 22 + .../HAL_TEENSY31_32/{ => inc}/SanityCheck.h | 0 .../HAL_TEENSY31_32/persistent_store_impl.cpp | 34 +- Marlin/src/HAL/HAL_TEENSY35_36/HAL.h | 8 +- .../HAL/HAL_TEENSY35_36/HAL_timers_Teensy.h | 8 +- .../HAL_TEENSY35_36/inc/Conditionals_LCD.h | 22 + .../HAL_TEENSY35_36/inc/Conditionals_adv.h | 22 + .../HAL_TEENSY35_36/inc/Conditionals_post.h | 22 + .../HAL_TEENSY35_36/{ => inc}/SanityCheck.h | 0 .../HAL_TEENSY35_36/persistent_store_impl.cpp | 50 - Marlin/src/HAL/HAL_TEENSY35_36/pinsDebug.h | 5 +- Marlin/src/HAL/platforms.h | 8 +- Marlin/src/HAL/shared/Marduino.h | 6 + .../src/HAL/shared/backtrace/unwmemaccess.cpp | 11 + .../shared/{I2cEeprom.cpp => eeprom_i2c.cpp} | 49 +- .../shared/{SpiEeprom.cpp => eeprom_spi.cpp} | 2 +- Marlin/src/HAL/shared/servo.cpp | 5 +- Marlin/src/HAL/shared/servo.h | 6 +- Marlin/src/HAL/shared/servo_private.h | 12 +- Marlin/src/Marlin.cpp | 21 +- Marlin/src/core/boards.h | 175 +- Marlin/src/core/drivers.h | 4 +- Marlin/src/core/language.h | 20 +- Marlin/src/core/macros.h | 69 +- Marlin/src/core/minmax.h | 80 - Marlin/src/core/serial.h | 10 +- Marlin/src/feature/I2CPositionEncoder.cpp | 1 - Marlin/src/feature/Max7219_Debug_LEDs.cpp | 225 +- Marlin/src/feature/Max7219_Debug_LEDs.h | 11 - Marlin/src/feature/backlash.cpp | 2 +- Marlin/src/feature/backlash.h | 2 +- Marlin/src/feature/bedlevel/abl/abl.cpp | 14 +- Marlin/src/feature/bedlevel/bedlevel.cpp | 8 +- Marlin/src/feature/bedlevel/bedlevel.h | 12 + .../bedlevel/mbl/mesh_bed_leveling.cpp | 6 +- Marlin/src/feature/bedlevel/ubl/ubl.cpp | 2 +- Marlin/src/feature/bedlevel/ubl/ubl.h | 10 +- Marlin/src/feature/bedlevel/ubl/ubl_G29.cpp | 30 +- .../src/feature/bedlevel/ubl/ubl_motion.cpp | 4 +- Marlin/src/feature/bltouch.cpp | 2 +- Marlin/src/feature/dac/dac_mcp4728.cpp | 2 +- .../src/feature/digipot/digipot_mcp4018.cpp | 2 +- .../src/feature/digipot/digipot_mcp4451.cpp | 2 +- Marlin/src/feature/host_actions.cpp | 22 +- Marlin/src/feature/leds/leds.cpp | 29 +- Marlin/src/feature/leds/neopixel.cpp | 66 +- Marlin/src/feature/leds/neopixel.h | 80 +- Marlin/src/feature/leds/pca9632.cpp | 53 +- Marlin/src/feature/leds/pca9632.h | 4 + .../src/feature/leds/printer_event_leds.cpp | 2 +- Marlin/src/feature/leds/printer_event_leds.h | 12 +- Marlin/src/feature/leds/tempstat.cpp | 4 +- Marlin/src/feature/mixing.cpp | 2 +- Marlin/src/feature/mixing.h | 6 +- Marlin/src/feature/pause.cpp | 8 +- Marlin/src/feature/power_loss_recovery.cpp | 1 + Marlin/src/feature/power_loss_recovery.h | 2 + Marlin/src/feature/prusa_MMU2/mmu2.cpp | 2 +- Marlin/src/feature/spindle_laser.h | 5 +- Marlin/src/feature/tmc_util.cpp | 22 +- Marlin/src/feature/tmc_util.h | 8 +- Marlin/src/feature/touch/xpt2046.cpp | 141 + Marlin/src/feature/touch/xpt2046.h | 50 + Marlin/src/gcode/bedlevel/G26.cpp | 24 +- Marlin/src/gcode/bedlevel/abl/G29.cpp | 56 +- Marlin/src/gcode/bedlevel/mbl/G29.cpp | 6 +- Marlin/src/gcode/calibrate/G28.cpp | 13 +- Marlin/src/gcode/calibrate/G33.cpp | 2 +- Marlin/src/gcode/calibrate/G34_M422.cpp | 28 +- Marlin/src/gcode/calibrate/G425.cpp | 21 +- Marlin/src/gcode/calibrate/M100.cpp | 16 +- Marlin/src/gcode/calibrate/M48.cpp | 17 +- Marlin/src/gcode/config/M200-M205.cpp | 4 +- Marlin/src/gcode/config/M217.cpp | 17 +- Marlin/src/gcode/config/M43.cpp | 12 +- Marlin/src/gcode/config/M575.cpp | 74 + Marlin/src/gcode/config/M92.cpp | 2 +- Marlin/src/gcode/control/M605.cpp | 2 +- Marlin/src/gcode/feature/advance/M900.cpp | 26 +- Marlin/src/gcode/feature/clean/G12.cpp | 19 +- Marlin/src/gcode/feature/leds/M150.cpp | 2 +- Marlin/src/gcode/feature/leds/M7219.cpp | 22 +- Marlin/src/gcode/feature/pause/G27.cpp | 2 +- Marlin/src/gcode/feature/pause/M125.cpp | 2 +- Marlin/src/gcode/feature/pause/M600.cpp | 2 +- Marlin/src/gcode/feature/pause/M701_M702.cpp | 8 +- Marlin/src/gcode/feature/runout/M412.cpp | 4 +- Marlin/src/gcode/feature/trinamic/M122.cpp | 2 +- Marlin/src/gcode/gcode.cpp | 4 + Marlin/src/gcode/gcode.h | 5 +- Marlin/src/gcode/lcd/M117.cpp | 5 +- Marlin/src/gcode/lcd/M73.cpp | 4 +- Marlin/src/gcode/queue.cpp | 13 +- Marlin/src/gcode/sdcard/M23.cpp | 5 + Marlin/src/gcode/temperature/M104_M109.cpp | 2 +- Marlin/src/gcode/temperature/M106_M107.cpp | 2 +- Marlin/src/inc/Conditionals_LCD.h | 223 +- Marlin/src/inc/Conditionals_post.h | 56 +- Marlin/src/inc/MarlinConfig.h | 13 +- Marlin/src/inc/MarlinConfigPre.h | 6 + Marlin/src/inc/SanityCheck.h | 205 +- Marlin/src/inc/Version.h | 4 +- Marlin/src/lcd/HD44780/ultralcd_HD44780.cpp | 10 +- Marlin/src/lcd/dogm/HAL_LCD_com_defines.h | 30 +- Marlin/src/lcd/dogm/dogm_Statusscreen.h | 2 +- Marlin/src/lcd/dogm/status_screen_DOGM.cpp | 66 +- .../lcd/dogm/status_screen_lite_ST7920.cpp | 22 +- ...8g_dev_tft_320x240_upscale_from_128x64.cpp | 326 ++- Marlin/src/lcd/dogm/ultralcd_DOGM.cpp | 148 +- Marlin/src/lcd/dogm/ultralcd_DOGM.h | 2 +- .../dogm/ultralcd_st7920_u8glib_rrd_AVR.cpp | 16 +- .../extensible_ui/lib/dgus/DGUSDisplay.cpp | 2 +- Marlin/src/lcd/extensible_ui/ui_api.cpp | 11 +- Marlin/src/lcd/extensible_ui/ui_api.h | 2 - Marlin/src/lcd/extui_example.cpp | 2 +- Marlin/src/lcd/extui_malyan_lcd.cpp | 58 +- Marlin/src/lcd/fontutils.cpp | 2 +- Marlin/src/lcd/language/language_an.h | 2 +- Marlin/src/lcd/language/language_bg.h | 2 +- Marlin/src/lcd/language/language_ca.h | 2 +- Marlin/src/lcd/language/language_cz.h | 2 +- Marlin/src/lcd/language/language_da.h | 2 +- Marlin/src/lcd/language/language_de.h | 73 +- Marlin/src/lcd/language/language_el-gr.h | 2 +- Marlin/src/lcd/language/language_el.h | 2 +- Marlin/src/lcd/language/language_en.h | 245 +- Marlin/src/lcd/language/language_es.h | 2 +- Marlin/src/lcd/language/language_eu.h | 2 +- Marlin/src/lcd/language/language_fi.h | 2 +- Marlin/src/lcd/language/language_fr.h | 8 +- Marlin/src/lcd/language/language_gl.h | 2 +- Marlin/src/lcd/language/language_hr.h | 2 +- Marlin/src/lcd/language/language_it.h | 9 +- Marlin/src/lcd/language/language_jp-kana.h | 2 +- Marlin/src/lcd/language/language_ko_KR.h | 2 +- Marlin/src/lcd/language/language_nl.h | 2 +- Marlin/src/lcd/language/language_pl.h | 2 +- Marlin/src/lcd/language/language_pt-br.h | 2 +- Marlin/src/lcd/language/language_pt.h | 2 +- Marlin/src/lcd/language/language_ru.h | 63 +- Marlin/src/lcd/language/language_sk.h | 4 +- Marlin/src/lcd/language/language_tr.h | 2 +- Marlin/src/lcd/language/language_uk.h | 2 +- Marlin/src/lcd/language/language_zh_CN.h | 2 +- Marlin/src/lcd/language/language_zh_TW.h | 2 +- Marlin/src/lcd/menu/game/brickout.cpp | 99 +- .../menu/game/brickout.h} | 27 +- Marlin/src/lcd/menu/game/game.cpp | 3 +- Marlin/src/lcd/menu/game/game.h | 58 +- Marlin/src/lcd/menu/game/invaders.cpp | 261 +- Marlin/src/lcd/menu/game/invaders.h | 62 + Marlin/src/lcd/menu/game/maze.cpp | 4 +- Marlin/src/lcd/menu/game/maze.h | 30 + Marlin/src/lcd/menu/game/snake.cpp | 132 +- Marlin/src/lcd/menu/game/snake.h | 38 + .../SanityCheck.h => lcd/menu/game/types.h} | 33 +- Marlin/src/lcd/menu/menu.cpp | 68 +- Marlin/src/lcd/menu/menu.h | 7 +- Marlin/src/lcd/menu/menu_advanced.cpp | 16 +- Marlin/src/lcd/menu/menu_bed_corners.cpp | 2 +- Marlin/src/lcd/menu/menu_bed_leveling.cpp | 7 +- Marlin/src/lcd/menu/menu_configuration.cpp | 43 +- Marlin/src/lcd/menu/menu_custom.cpp | 2 +- Marlin/src/lcd/menu/menu_delta_calibrate.cpp | 2 +- Marlin/src/lcd/menu/menu_info.cpp | 93 +- Marlin/src/lcd/menu/menu_main.cpp | 6 +- Marlin/src/lcd/menu/menu_mixer.cpp | 13 +- Marlin/src/lcd/menu/menu_motion.cpp | 39 +- Marlin/src/lcd/menu/menu_service.cpp | 4 +- Marlin/src/lcd/menu/menu_temperature.cpp | 2 +- Marlin/src/lcd/menu/menu_tune.cpp | 1 - Marlin/src/lcd/menu/menu_ubl.cpp | 1 - Marlin/src/lcd/ultralcd.cpp | 61 +- Marlin/src/lcd/ultralcd.h | 73 +- Marlin/src/libs/least_squares_fit.h | 8 +- Marlin/src/libs/nozzle.cpp | 54 +- Marlin/src/libs/nozzle.h | 4 +- Marlin/src/libs/vector_3.h | 2 - Marlin/src/module/configuration_store.cpp | 27 +- Marlin/src/module/configuration_store.h | 10 +- Marlin/src/module/delta.cpp | 2 +- Marlin/src/module/delta.h | 2 - Marlin/src/module/endstops.cpp | 9 +- Marlin/src/module/endstops.h | 23 +- Marlin/src/module/motion.cpp | 40 +- Marlin/src/module/motion.h | 2 +- Marlin/src/module/planner.cpp | 34 +- Marlin/src/module/planner.h | 10 +- Marlin/src/module/printcounter.cpp | 6 +- Marlin/src/module/probe.cpp | 10 +- Marlin/src/module/scara.h | 2 - Marlin/src/module/stepper.cpp | 4 +- Marlin/src/module/stepper.h | 6 +- Marlin/src/module/stepper_indirection.cpp | 6 +- Marlin/src/module/stepper_indirection.h | 6 +- Marlin/src/module/temperature.cpp | 212 +- Marlin/src/module/temperature.h | 18 +- Marlin/src/module/thermistor/thermistor_501.h | 64 +- Marlin/src/module/thermistor/thermistor_512.h | 87 + Marlin/src/module/thermistor/thermistors.h | 3 + Marlin/src/module/tool_change.cpp | 484 ++-- Marlin/src/module/tool_change.h | 2 +- Marlin/src/pins/{ => esp32}/pins_ESP32.h | 0 .../src/pins/{ => linux}/pins_RAMPS_LINUX.h | 120 +- .../src/pins/{ => lpc1768}/pins_AZSMZ_MINI.h | 0 .../pins_BIGTREE_SKR_V1.1.h} | 4 +- .../{ => lpc1768}/pins_BIGTREE_SKR_V1.3.h | 24 +- .../pins/{ => lpc1768}/pins_BIQU_B300_V1.0.h | 12 +- .../pins/{ => lpc1768}/pins_BIQU_BQ111_A4.h | 0 Marlin/src/pins/lpc1768/pins_GMARSH_X6_REV1.h | 160 + .../src/pins/{ => lpc1768}/pins_MKS_SBASE.h | 77 +- .../src/pins/{ => lpc1768}/pins_MKS_SGEN_L.h | 20 +- .../pins/{ => lpc1768}/pins_RAMPS_RE_ARM.h | 68 +- .../pins/{ => lpc1768}/pins_SELENA_COMPACT.h | 0 .../pins/{ => lpc1768}/pins_TH3D_EZBOARD.h | 0 .../pins/{ => lpc1769}/pins_AZTEEG_X5_GT.h | 2 +- .../pins/{ => lpc1769}/pins_AZTEEG_X5_MINI.h | 2 +- .../{ => lpc1769}/pins_AZTEEG_X5_MINI_WIFI.h | 2 +- .../pins/{ => lpc1769}/pins_COHESION3D_MINI.h | 0 .../{ => lpc1769}/pins_COHESION3D_REMIX.h | 0 Marlin/src/pins/{ => lpc1769}/pins_MKS_SGEN.h | 20 +- .../pins/{ => lpc1769}/pins_SMOOTHIEBOARD.h | 0 Marlin/src/pins/{ => mega}/pins_CHEAPTRONIC.h | 0 .../src/pins/{ => mega}/pins_CHEAPTRONICv2.h | 1 - .../src/pins/{ => mega}/pins_CNCONTROLS_11.h | 0 .../src/pins/{ => mega}/pins_CNCONTROLS_12.h | 0 Marlin/src/pins/{ => mega}/pins_EINSTART-S.h | 12 +- Marlin/src/pins/{ => mega}/pins_ELEFU_3.h | 0 .../src/pins/{ => mega}/pins_GT2560_REV_A.h | 1 - .../pins/{ => mega}/pins_GT2560_REV_A_PLUS.h | 0 Marlin/src/pins/{ => mega}/pins_GT2560_V3.h | 36 +- .../src/pins/{ => mega}/pins_GT2560_V3_A20.h | 11 +- .../src/pins/{ => mega}/pins_GT2560_V3_MC2.h | 0 Marlin/src/pins/{ => mega}/pins_LEAPFROG.h | 0 .../src/pins/{ => mega}/pins_MEGACONTROLLER.h | 8 +- Marlin/src/pins/{ => mega}/pins_MEGATRONICS.h | 6 +- .../src/pins/{ => mega}/pins_MEGATRONICS_2.h | 6 +- .../src/pins/{ => mega}/pins_MEGATRONICS_3.h | 8 +- .../pins/{ => mega}/pins_MIGHTYBOARD_REVE.h | 4 +- Marlin/src/pins/{ => mega}/pins_MINITRONICS.h | 4 +- Marlin/src/pins/mega/pins_OVERLORD.h | 144 + Marlin/src/pins/{ => mega}/pins_SILVER_GATE.h | 0 Marlin/src/pins/mega/pins_WANHAO_ONEPLUS.h | 111 + Marlin/src/pins/pins.h | 494 ++-- Marlin/src/pins/pinsDebug.h | 23 +- Marlin/src/pins/pinsDebug_list.h | 23 +- Marlin/src/pins/pins_GTM32_PRO_VB.h | 195 -- .../src/pins/{ => rambo}/pins_EINSY_RAMBO.h | 4 +- .../src/pins/{ => rambo}/pins_EINSY_RETRO.h | 4 +- Marlin/src/pins/{ => rambo}/pins_MINIRAMBO.h | 4 +- Marlin/src/pins/{ => rambo}/pins_RAMBO.h | 4 +- Marlin/src/pins/{ => rambo}/pins_SCOOVO_X9H.h | 0 Marlin/src/pins/{ => ramps}/pins_3DRAG.h | 10 +- Marlin/src/pins/{ => ramps}/pins_AZTEEG_X3.h | 8 +- .../src/pins/{ => ramps}/pins_AZTEEG_X3_PRO.h | 13 +- .../src/pins/{ => ramps}/pins_BAM_DICE_DUE.h | 4 +- Marlin/src/pins/{ => ramps}/pins_BIQU_KFB_2.h | 0 .../pins/{ => ramps}/pins_BQ_ZUM_MEGA_3D.h | 6 +- .../{ => ramps}/pins_DUPLICATOR_I3_PLUS.h | 2 +- Marlin/src/pins/{ => ramps}/pins_FELIX2.h | 3 +- .../pins/{ => ramps}/pins_FORMBOT_RAPTOR.h | 20 +- .../pins/{ => ramps}/pins_FORMBOT_RAPTOR2.h | 14 +- .../pins/{ => ramps}/pins_FORMBOT_TREX2PLUS.h | 14 +- .../src/pins/{ => ramps}/pins_FORMBOT_TREX3.h | 16 +- .../src/pins/{ => ramps}/pins_FYSETC_F6_13.h | 12 +- Marlin/src/pins/{ => ramps}/pins_K8200.h | 0 Marlin/src/pins/{ => ramps}/pins_K8400.h | 2 +- Marlin/src/pins/{ => ramps}/pins_K8800.h | 2 +- .../pins/{ => ramps}/pins_MAKEBOARD_MINI.h | 13 +- Marlin/src/pins/{ => ramps}/pins_MKS_BASE.h | 4 +- .../src/pins/{ => ramps}/pins_MKS_BASE_14.h | 0 .../src/pins/{ => ramps}/pins_MKS_BASE_15.h | 0 .../pins/{ => ramps}/pins_MKS_BASE_HEROIC.h | 0 Marlin/src/pins/{ => ramps}/pins_MKS_GEN_13.h | 2 + Marlin/src/pins/{ => ramps}/pins_MKS_GEN_L.h | 0 Marlin/src/pins/{ => ramps}/pins_RAMPS.h | 134 +- Marlin/src/pins/{ => ramps}/pins_RAMPS_13.h | 0 .../pins/{ => ramps}/pins_RAMPS_CREALITY.h | 0 .../src/pins/{ => ramps}/pins_RAMPS_DAGOMA.h | 0 .../src/pins/{ => ramps}/pins_RAMPS_ENDER_4.h | 0 Marlin/src/pins/{ => ramps}/pins_RAMPS_OLD.h | 12 +- Marlin/src/pins/{ => ramps}/pins_RAMPS_PLUS.h | 0 Marlin/src/pins/{ => ramps}/pins_RIGIDBOARD.h | 4 +- .../src/pins/{ => ramps}/pins_RIGIDBOARD_V2.h | 5 +- Marlin/src/pins/{ => ramps}/pins_RL200.h | 2 +- Marlin/src/pins/{ => ramps}/pins_RUMBA.h | 15 +- .../src/pins/{ => ramps}/pins_RUMBA_RAISE3D.h | 2 +- .../pins/{ => ramps}/pins_SAINSMART_2IN1.h | 0 .../src/pins/{ => ramps}/pins_TRIGORILLA_13.h | 0 .../src/pins/{ => ramps}/pins_TRIGORILLA_14.h | 0 .../src/pins/{ => ramps}/pins_TRONXY_V3_1_0.h | 4 +- Marlin/src/pins/ramps/pins_TT_OSCAR.h | 512 ++++ Marlin/src/pins/{ => ramps}/pins_ULTIMAIN_2.h | 6 +- Marlin/src/pins/{ => ramps}/pins_ULTIMAKER.h | 8 +- .../src/pins/{ => ramps}/pins_ULTIMAKER_OLD.h | 18 +- Marlin/src/pins/{ => ramps}/pins_VORON.h | 0 Marlin/src/pins/{ => ramps}/pins_ZRIB_V20.h | 0 .../pins/{ => ramps}/pins_Z_BOLT_X_SERIES.h | 128 +- Marlin/src/pins/{ => sam}/pins_ADSK.h | 0 Marlin/src/pins/{ => sam}/pins_ALLIGATOR_R2.h | 0 Marlin/src/pins/{ => sam}/pins_ARCHIM1.h | 0 Marlin/src/pins/{ => sam}/pins_ARCHIM2.h | 12 +- Marlin/src/pins/{ => sam}/pins_DUE3DOM.h | 0 Marlin/src/pins/{ => sam}/pins_DUE3DOM_MINI.h | 0 .../src/pins/{ => sam}/pins_PRINTRBOARD_G2.h | 0 Marlin/src/pins/{ => sam}/pins_RADDS.h | 3 +- Marlin/src/pins/{ => sam}/pins_RAMPS4DUE.h | 9 +- Marlin/src/pins/{ => sam}/pins_RAMPS_DUO.h | 4 +- Marlin/src/pins/{ => sam}/pins_RAMPS_FD_V1.h | 4 +- Marlin/src/pins/{ => sam}/pins_RAMPS_FD_V2.h | 0 Marlin/src/pins/{ => sam}/pins_RAMPS_SMART.h | 4 +- Marlin/src/pins/{ => sam}/pins_RURAMPS4D_11.h | 0 Marlin/src/pins/{ => sam}/pins_RURAMPS4D_13.h | 0 .../pins/{ => sam}/pins_ULTRATRONICS_PRO.h | 0 .../src/pins/samd/pins_AGCM4_RURAMPS4D_13.h | 254 ++ Marlin/src/pins/{ => sanguino}/pins_ANET_10.h | 0 .../src/pins/{ => sanguino}/pins_AZTEEG_X1.h | 0 .../{ => sanguino}/pins_GEN3_MONOLITHIC.h | 0 .../src/pins/{ => sanguino}/pins_GEN3_PLUS.h | 0 Marlin/src/pins/{ => sanguino}/pins_GEN6.h | 6 +- .../pins/{ => sanguino}/pins_GEN6_DELUXE.h | 0 Marlin/src/pins/{ => sanguino}/pins_GEN7_12.h | 12 +- Marlin/src/pins/{ => sanguino}/pins_GEN7_13.h | 0 Marlin/src/pins/{ => sanguino}/pins_GEN7_14.h | 6 +- .../pins/{ => sanguino}/pins_GEN7_CUSTOM.h | 6 +- Marlin/src/pins/{ => sanguino}/pins_MELZI.h | 0 .../pins/{ => sanguino}/pins_MELZI_CREALITY.h | 0 .../pins/{ => sanguino}/pins_MELZI_MAKR3D.h | 0 .../pins/{ => sanguino}/pins_MELZI_MALYAN.h | 0 .../pins/{ => sanguino}/pins_MELZI_TRONXY.h | 0 Marlin/src/pins/{ => sanguino}/pins_OMCA.h | 0 Marlin/src/pins/{ => sanguino}/pins_OMCA_A.h | 0 .../{ => sanguino}/pins_SANGUINOLOLU_11.h | 10 +- .../{ => sanguino}/pins_SANGUINOLOLU_12.h | 0 Marlin/src/pins/{ => sanguino}/pins_SETHI.h | 2 +- Marlin/src/pins/{ => sanguino}/pins_STB_11.h | 1 + Marlin/src/pins/sensitive_pins.h | 2 +- Marlin/src/pins/{ => stm32}/pins_ARMED.h | 110 +- Marlin/src/pins/{ => stm32}/pins_BEAST.h | 13 +- .../src/pins/stm32/pins_BIGTREE_SKR_E3_DIP.h | 183 ++ .../{ => stm32}/pins_BIGTREE_SKR_MINI_E3.h | 15 +- .../{ => stm32}/pins_BIGTREE_SKR_MINI_V1_1.h | 20 +- .../pins/stm32/pins_BIGTREE_SKR_PRO_V1.1.h | 244 ++ .../pins/{ => stm32}/pins_BLACK_STM32F407VE.h | 17 +- Marlin/src/pins/{ => stm32}/pins_CHITU3D.h | 13 +- .../src/pins/{ => stm32}/pins_FYSETC_AIO_II.h | 12 +- .../pins/{ => stm32}/pins_FYSETC_CHEETAH.h | 10 +- .../src/pins/stm32/pins_FYSETC_CHEETAH_V12.h | 60 + Marlin/src/pins/stm32/pins_GTM32_PRO_VB.h | 234 ++ .../pins/{ => stm32}/pins_JGAURORA_A5S_A1.h | 54 +- Marlin/src/pins/stm32/pins_LONGER3D_LK.h | 158 + .../src/pins/{ => stm32}/pins_MALYAN_M200.h | 2 +- Marlin/src/pins/{ => stm32}/pins_MKS_ROBIN.h | 16 +- Marlin/src/pins/stm32/pins_MKS_ROBIN_LITE.h | 143 + .../pins/{ => stm32}/pins_MKS_ROBIN_MINI.h | 55 +- .../pins/{ => stm32}/pins_MKS_ROBIN_NANO.h | 53 +- Marlin/src/pins/{ => stm32}/pins_MORPHEUS.h | 0 Marlin/src/pins/{ => stm32}/pins_REMRAM_V1.h | 4 +- Marlin/src/pins/{ => stm32}/pins_RUMBA32.h | 13 +- Marlin/src/pins/{ => stm32}/pins_STEVAL.h | 4 +- Marlin/src/pins/{ => stm32}/pins_STM32F1R.h | 11 +- Marlin/src/pins/{ => stm32}/pins_STM32F4.h | 14 +- Marlin/src/pins/{ => stm32}/pins_STM3R_MINI.h | 177 +- Marlin/src/pins/{ => stm32}/pins_THE_BORG.h | 16 +- Marlin/src/pins/{ => teensy2}/pins_5DPRINT.h | 0 .../src/pins/{ => teensy2}/pins_BRAINWAVE.h | 0 .../pins/{ => teensy2}/pins_BRAINWAVE_PRO.h | 0 .../src/pins/{ => teensy2}/pins_PRINTRBOARD.h | 0 .../{ => teensy2}/pins_PRINTRBOARD_REVF.h | 0 Marlin/src/pins/{ => teensy2}/pins_SAV_MKI.h | 4 +- Marlin/src/pins/{ => teensy2}/pins_TEENSY2.h | 0 Marlin/src/pins/{ => teensy2}/pins_TEENSYLU.h | 0 .../src/pins/{ => teensy3}/pins_TEENSY31_32.h | 91 +- .../src/pins/{ => teensy3}/pins_TEENSY35_36.h | 0 Marlin/src/sd/Sd2Card.cpp | 4 +- Marlin/src/sd/Sd2Card.h | 6 +- Marlin/src/sd/SdVolume.h | 5 +- Marlin/src/sd/cardreader.cpp | 35 +- .../sd/usb_flashdrive/Sd2Card_FlashDrive.cpp | 8 +- .../sd/usb_flashdrive/Sd2Card_FlashDrive.h | 4 +- config/default/Configuration.h | 126 +- config/default/Configuration_adv.h | 14 +- .../examples/3DFabXYZ/Migbot/Configuration.h | 126 +- .../3DFabXYZ/Migbot/Configuration_adv.h | 14 +- .../AlephObjects/TAZ4/Configuration.h | 126 +- .../AlephObjects/TAZ4/Configuration_adv.h | 14 +- config/examples/Alfawise/U20/Configuration.h | 2314 +++++++++++++++ .../examples/Alfawise/U20/Configuration_adv.h | 2564 +++++++++++++++++ config/examples/Alfawise/U20/_Statusscreen.h | 77 + .../AliExpress/CL-260/Configuration.h | 126 +- .../AliExpress/UM2pExt/Configuration.h | 126 +- .../AliExpress/UM2pExt/Configuration_adv.h | 14 +- config/examples/Anet/A2/Configuration.h | 126 +- config/examples/Anet/A2/Configuration_adv.h | 14 +- config/examples/Anet/A2plus/Configuration.h | 126 +- .../examples/Anet/A2plus/Configuration_adv.h | 14 +- config/examples/Anet/A6/Configuration.h | 126 +- config/examples/Anet/A6/Configuration_adv.h | 14 +- config/examples/Anet/A8/Configuration.h | 126 +- config/examples/Anet/A8/Configuration_adv.h | 14 +- config/examples/Anet/A8plus/Configuration.h | 126 +- .../examples/Anet/A8plus/Configuration_adv.h | 14 +- config/examples/Anet/E16/Configuration.h | 126 +- config/examples/Anet/E16/Configuration_adv.h | 14 +- config/examples/AnyCubic/i3/Configuration.h | 126 +- .../examples/AnyCubic/i3/Configuration_adv.h | 14 +- config/examples/ArmEd/Configuration.h | 126 +- config/examples/ArmEd/Configuration_adv.h | 14 +- config/examples/Azteeg/X5GT/Configuration.h | 126 +- .../BIBO/TouchX/cyclops/Configuration.h | 126 +- .../BIBO/TouchX/cyclops/Configuration_adv.h | 14 +- .../BIBO/TouchX/default/Configuration.h | 126 +- .../BIBO/TouchX/default/Configuration_adv.h | 14 +- config/examples/BQ/Hephestos/Configuration.h | 126 +- .../examples/BQ/Hephestos/Configuration_adv.h | 14 +- .../examples/BQ/Hephestos_2/Configuration.h | 126 +- .../BQ/Hephestos_2/Configuration_adv.h | 14 +- config/examples/BQ/WITBOX/Configuration.h | 126 +- config/examples/BQ/WITBOX/Configuration_adv.h | 14 +- config/examples/Cartesio/Configuration.h | 126 +- config/examples/Cartesio/Configuration_adv.h | 14 +- .../examples/Creality/CR-10/Configuration.h | 126 +- .../Creality/CR-10/Configuration_adv.h | 14 +- .../examples/Creality/CR-10S/Configuration.h | 126 +- .../Creality/CR-10S/Configuration_adv.h | 14 +- .../Creality/CR-10_5S/Configuration.h | 126 +- .../Creality/CR-10_5S/Configuration_adv.h | 14 +- .../Creality/CR-10mini/Configuration.h | 126 +- .../Creality/CR-10mini/Configuration_adv.h | 14 +- .../Creality/CR-20 Pro/Configuration.h | 138 +- .../Creality/CR-20 Pro/Configuration_adv.h | 14 +- .../Creality/CR-20 Pro/_Statusscreen.h | 4 +- .../examples/Creality/CR-20/Configuration.h | 138 +- .../Creality/CR-20/Configuration_adv.h | 14 +- config/examples/Creality/CR-8/Configuration.h | 126 +- .../Creality/CR-8/Configuration_adv.h | 14 +- .../examples/Creality/Ender-2/Configuration.h | 130 +- .../Creality/Ender-2/Configuration_adv.h | 14 +- .../examples/Creality/Ender-3/Configuration.h | 126 +- .../Creality/Ender-3/Configuration_adv.h | 14 +- config/examples/Creality/Ender-3/README.md | 18 - .../examples/Creality/Ender-4/Configuration.h | 126 +- .../Creality/Ender-4/Configuration_adv.h | 14 +- .../examples/Creality/Ender-5/Configuration.h | 144 +- .../Creality/Ender-5/Configuration_adv.h | 16 +- .../examples/Creality/Ender-5/_Bootscreen.h | 4 +- .../examples/Creality/Ender-5/_Statusscreen.h | 4 +- .../Dagoma/Disco Ultimate/Configuration.h | 126 +- .../Dagoma/Disco Ultimate/Configuration_adv.h | 14 +- .../Sidewinder X1/Configuration.h | 126 +- .../Sidewinder X1/Configuration_adv.h | 14 +- config/examples/Einstart-S/Configuration.h | 131 +- .../examples/Einstart-S/Configuration_adv.h | 14 +- .../Cheetah 1.2/BLTouch/Configuration.h | 2222 ++++++++++++++ .../Cheetah 1.2/BLTouch/Configuration_adv.h | 2562 ++++++++++++++++ .../FYSETC/Cheetah 1.2/base/Configuration.h | 2221 ++++++++++++++ .../Cheetah 1.2/base}/Configuration_adv.h | 19 +- .../Cheetah/BLTouch}/Configuration.h | 138 +- .../Cheetah/BLTouch/Configuration_adv.h | 2561 ++++++++++++++++ .../FYSETC/Cheetah/base/Configuration.h | 2221 ++++++++++++++ .../FYSETC/Cheetah/base/Configuration_adv.h | 2561 ++++++++++++++++ config/examples/Felix/Configuration.h | 126 +- config/examples/Felix/Configuration_adv.h | 14 +- config/examples/Felix/DUAL/Configuration.h | 126 +- .../FlashForge/CreatorPro/Configuration.h | 126 +- .../FlashForge/CreatorPro/Configuration_adv.h | 14 +- .../FolgerTech/i3-2020/Configuration.h | 126 +- .../FolgerTech/i3-2020/Configuration_adv.h | 14 +- .../examples/Formbot/Raptor/Configuration.h | 126 +- .../Formbot/Raptor/Configuration_adv.h | 16 +- .../examples/Formbot/T_Rex_2+/Configuration.h | 126 +- .../Formbot/T_Rex_2+/Configuration_adv.h | 16 +- .../examples/Formbot/T_Rex_3/Configuration.h | 126 +- .../Formbot/T_Rex_3/Configuration_adv.h | 14 +- config/examples/Fysetc/AIO_II/Configuration.h | 201 +- .../Fysetc/AIO_II/Configuration_adv.h | 36 +- config/examples/Fysetc/F6_13/Configuration.h | 138 +- .../examples/Fysetc/F6_13/Configuration_adv.h | 14 +- config/examples/Geeetech/A10/Configuration.h | 126 +- .../examples/Geeetech/A10/Configuration_adv.h | 14 +- config/examples/Geeetech/A10M/Configuration.h | 126 +- .../Geeetech/A10M/Configuration_adv.h | 14 +- config/examples/Geeetech/A20M/Configuration.h | 126 +- .../Geeetech/A20M/Configuration_adv.h | 14 +- .../examples/Geeetech/GT2560/Configuration.h | 126 +- .../Geeetech/I3_Pro_X-GT2560/Configuration.h | 126 +- .../Geeetech/MeCreator2/Configuration.h | 126 +- .../Geeetech/MeCreator2/Configuration_adv.h | 14 +- .../Prusa i3 Pro B/bltouch/Configuration.h | 126 +- .../Prusa i3 Pro B/noprobe/Configuration.h | 126 +- .../Geeetech/Prusa i3 Pro C/Configuration.h | 126 +- .../Prusa i3 Pro C/Configuration_adv.h | 14 +- .../Geeetech/Prusa i3 Pro W/Configuration.h | 126 +- .../Prusa i3 Pro W/Configuration_adv.h | 14 +- .../examples/Infitary/i3-M508/Configuration.h | 126 +- .../Infitary/i3-M508/Configuration_adv.h | 14 +- config/examples/JGAurora/A1/Configuration.h | 155 +- .../examples/JGAurora/A1/Configuration_adv.h | 76 +- config/examples/JGAurora/A5/Configuration.h | 126 +- .../examples/JGAurora/A5/Configuration_adv.h | 14 +- config/examples/JGAurora/A5S/Configuration.h | 156 +- .../examples/JGAurora/A5S/Configuration_adv.h | 76 +- config/examples/MakerParts/Configuration.h | 126 +- .../examples/MakerParts/Configuration_adv.h | 14 +- config/examples/Malyan/M150/Configuration.h | 126 +- .../examples/Malyan/M150/Configuration_adv.h | 14 +- config/examples/Malyan/M200/Configuration.h | 126 +- .../examples/Malyan/M200/Configuration_adv.h | 14 +- .../Micromake/C1/basic/Configuration.h | 126 +- .../Micromake/C1/enhanced/Configuration.h | 126 +- .../Micromake/C1/enhanced/Configuration_adv.h | 14 +- config/examples/Mks/Robin/Configuration.h | 126 +- config/examples/Mks/Robin/Configuration_adv.h | 14 +- config/examples/Mks/Sbase/Configuration.h | 126 +- config/examples/Mks/Sbase/Configuration_adv.h | 14 +- .../Printrbot/PrintrboardG2/Configuration.h | 122 +- .../examples/RapideLite/RL200/Configuration.h | 126 +- .../RapideLite/RL200/Configuration_adv.h | 14 +- .../examples/RepRapPro/Huxley/Configuration.h | 126 +- .../RepRapWorld/Megatronics/Configuration.h | 126 +- config/examples/RigidBot/Configuration.h | 126 +- config/examples/RigidBot/Configuration_adv.h | 14 +- config/examples/SCARA/Configuration.h | 126 +- config/examples/SCARA/Configuration_adv.h | 14 +- .../STM32/Black_STM32F407VET6/Configuration.h | 126 +- .../Black_STM32F407VET6/Configuration_adv.h | 14 +- .../examples/STM32/STM32F10/Configuration.h | 126 +- config/examples/STM32/STM32F4/Configuration.h | 126 +- .../STM32/stm32f103ret6/Configuration.h | 126 +- config/examples/Sanguinololu/Configuration.h | 126 +- .../examples/Sanguinololu/Configuration_adv.h | 14 +- .../Tevo/Michelangelo/Configuration.h | 2215 ++++++++++++++ .../Tevo/Michelangelo/Configuration_adv.h | 2561 ++++++++++++++++ .../examples/Tevo/Michelangelo/_Bootscreen.h | 83 + .../Tevo/Tarantula Pro/Configuration.h | 138 +- .../Tevo/Tarantula Pro/Configuration_adv.h | 14 +- .../Tornado/V1 (MKS Base)/Configuration.h | 2215 ++++++++++++++ .../Tornado/V1 (MKS Base)/Configuration_adv.h | 2561 ++++++++++++++++ .../Tornado/V2 (MKS GEN-L)/Configuration.h | 2215 ++++++++++++++ .../V2 (MKS GEN-L)/Configuration_adv.h | 2561 ++++++++++++++++ config/examples/Tevo/Tornado/_Bootscreen.h | 85 + config/examples/TheBorg/Configuration.h | 126 +- config/examples/TheBorg/Configuration_adv.h | 14 +- config/examples/TinyBoy2/Configuration.h | 126 +- config/examples/TinyBoy2/Configuration_adv.h | 14 +- config/examples/Tronxy/X1/Configuration.h | 126 +- config/examples/Tronxy/X3A/Configuration.h | 126 +- .../examples/Tronxy/X3A/Configuration_adv.h | 14 +- config/examples/Tronxy/X5S-2E/Configuration.h | 126 +- .../Tronxy/X5S-2E/Configuration_adv.h | 14 +- config/examples/Tronxy/X5S/Configuration.h | 126 +- config/examples/Tronxy/XY100/Configuration.h | 126 +- .../UltiMachine/Archim1/Configuration.h | 126 +- .../UltiMachine/Archim1/Configuration_adv.h | 14 +- .../UltiMachine/Archim2/Configuration.h | 126 +- .../UltiMachine/Archim2/Configuration_adv.h | 14 +- config/examples/VORONDesign/Configuration.h | 126 +- .../examples/VORONDesign/Configuration_adv.h | 14 +- .../examples/Velleman/K8200/Configuration.h | 89 +- .../Velleman/K8200/Configuration_adv.h | 14 +- .../examples/Velleman/K8400/Configuration.h | 126 +- .../Velleman/K8400/Configuration_adv.h | 14 +- .../Velleman/K8400/Dual-head/Configuration.h | 126 +- .../examples/WASP/PowerWASP/Configuration.h | 128 +- .../WASP/PowerWASP/Configuration_adv.h | 14 +- .../Wanhao/Duplicator 6/Configuration.h | 132 +- .../Wanhao/Duplicator 6/Configuration_adv.h | 14 +- .../Wanhao/Duplicator i3 Mini/Configuration.h | 2210 ++++++++++++++ .../Duplicator i3 Mini/Configuration_adv.h | 2562 ++++++++++++++++ .../examples/adafruit/ST7565/Configuration.h | 126 +- .../delta/Anycubic/Kossel/Configuration.h | 134 +- .../delta/Anycubic/Kossel/Configuration_adv.h | 14 +- .../FLSUN/auto_calibrate/Configuration.h | 126 +- .../FLSUN/auto_calibrate/Configuration_adv.h | 14 +- .../delta/FLSUN/kossel/Configuration.h | 126 +- .../delta/FLSUN/kossel/Configuration_adv.h | 14 +- .../delta/FLSUN/kossel_mini/Configuration.h | 126 +- .../FLSUN/kossel_mini/Configuration_adv.h | 14 +- .../Geeetech/Rostock 301/Configuration.h | 134 +- .../Geeetech/Rostock 301/Configuration_adv.h | 14 +- .../delta/Hatchbox_Alpha/Configuration.h | 134 +- .../examples/delta/MKS/SBASE/Configuration.h | 134 +- .../delta/MKS/SBASE/Configuration_adv.h | 14 +- .../delta/Tevo Little Monster/Configuration.h | 134 +- .../Tevo Little Monster/Configuration_adv.h | 14 +- config/examples/delta/generic/Configuration.h | 134 +- .../delta/generic/Configuration_adv.h | 14 +- .../delta/kossel_mini/Configuration.h | 134 +- .../delta/kossel_mini/Configuration_adv.h | 14 +- .../examples/delta/kossel_pro/Configuration.h | 134 +- .../examples/delta/kossel_xl/Configuration.h | 134 +- .../delta/kossel_xl/Configuration_adv.h | 14 +- .../examples/gCreate/gMax1.5+/Configuration.h | 126 +- .../gCreate/gMax1.5+/Configuration_adv.h | 14 +- config/examples/makibox/Configuration.h | 126 +- config/examples/makibox/Configuration_adv.h | 14 +- config/examples/tvrrug/Round2/Configuration.h | 126 +- .../tvrrug/Round2/Configuration_adv.h | 14 +- config/examples/wt150/Configuration.h | 126 +- config/examples/wt150/Configuration_adv.h | 14 +- 794 files changed, 61778 insertions(+), 11862 deletions(-) rename Marlin/src/HAL/{HAL_STM32F7/watchdog_STM32F7.h => HAL.h} (91%) rename Marlin/src/HAL/HAL_AVR/{ => fastio}/fastio_1280.h (99%) rename Marlin/src/HAL/HAL_AVR/{ => fastio}/fastio_1281.h (99%) rename Marlin/src/HAL/HAL_AVR/{ => fastio}/fastio_168.h (99%) rename Marlin/src/HAL/HAL_AVR/{ => fastio}/fastio_644.h (99%) rename Marlin/src/HAL/HAL_AVR/{ => fastio}/fastio_AT90USB.h (99%) create mode 100644 Marlin/src/HAL/HAL_AVR/inc/Conditionals_LCD.h create mode 100644 Marlin/src/HAL/HAL_AVR/inc/Conditionals_adv.h create mode 100644 Marlin/src/HAL/HAL_AVR/inc/Conditionals_post.h rename Marlin/src/HAL/HAL_AVR/{ => inc}/SanityCheck.h (100%) rename Marlin/src/HAL/HAL_DUE/{ => dogm}/u8g_com_HAL_DUE_shared_hw_spi.cpp (65%) rename Marlin/src/HAL/HAL_DUE/{ => dogm}/u8g_com_HAL_DUE_st7920_sw_spi.cpp (97%) rename Marlin/src/HAL/HAL_DUE/{ => dogm}/u8g_com_HAL_DUE_sw_spi.cpp (97%) rename Marlin/src/HAL/HAL_DUE/{ => dogm}/u8g_com_HAL_DUE_sw_spi_shared.cpp (98%) rename Marlin/src/HAL/HAL_DUE/{ => dogm}/u8g_com_HAL_DUE_sw_spi_shared.h (93%) rename Marlin/src/HAL/HAL_DUE/{ => fastio}/G2_PWM.cpp (99%) rename Marlin/src/HAL/HAL_DUE/{ => fastio}/G2_PWM.h (97%) rename Marlin/src/HAL/HAL_DUE/{ => fastio}/G2_pins.h (100%) create mode 100644 Marlin/src/HAL/HAL_DUE/inc/Conditionals_LCD.h create mode 100644 Marlin/src/HAL/HAL_DUE/inc/Conditionals_adv.h create mode 100644 Marlin/src/HAL/HAL_DUE/inc/Conditionals_post.h rename Marlin/src/HAL/HAL_DUE/{ => inc}/SanityCheck.h (100%) create mode 100644 Marlin/src/HAL/HAL_ESP32/inc/Conditionals_LCD.h create mode 100644 Marlin/src/HAL/HAL_ESP32/inc/Conditionals_adv.h create mode 100644 Marlin/src/HAL/HAL_ESP32/inc/Conditionals_post.h rename Marlin/src/HAL/HAL_ESP32/{ => inc}/SanityCheck.h (100%) create mode 100644 Marlin/src/HAL/HAL_LINUX/inc/Conditionals_LCD.h create mode 100644 Marlin/src/HAL/HAL_LINUX/inc/Conditionals_adv.h create mode 100644 Marlin/src/HAL/HAL_LINUX/inc/Conditionals_post.h rename Marlin/src/HAL/HAL_LINUX/{ => inc}/SanityCheck.h (100%) create mode 100644 Marlin/src/HAL/HAL_LPC1768/inc/Conditionals_LCD.h create mode 100644 Marlin/src/HAL/HAL_LPC1768/inc/Conditionals_adv.h create mode 100644 Marlin/src/HAL/HAL_LPC1768/inc/Conditionals_post.h rename Marlin/src/HAL/HAL_LPC1768/{ => inc}/SanityCheck.h (100%) create mode 100644 Marlin/src/HAL/HAL_SAMD51/HAL.cpp create mode 100644 Marlin/src/HAL/HAL_SAMD51/HAL.h create mode 100644 Marlin/src/HAL/HAL_SAMD51/HAL_spi_SAMD51.cpp create mode 100644 Marlin/src/HAL/HAL_SAMD51/HAL_timers_SAMD51.cpp create mode 100644 Marlin/src/HAL/HAL_SAMD51/HAL_timers_SAMD51.h create mode 100644 Marlin/src/HAL/HAL_SAMD51/MarlinSerial_AGCM4.cpp rename Marlin/src/HAL/{HAL_STM32F7/spi_pins.h => HAL_SAMD51/MarlinSerial_AGCM4.h} (85%) create mode 100644 Marlin/src/HAL/HAL_SAMD51/SAMD51.h create mode 100644 Marlin/src/HAL/HAL_SAMD51/ServoTimers.h create mode 100644 Marlin/src/HAL/HAL_SAMD51/Servo_SAMD51.cpp create mode 100644 Marlin/src/HAL/HAL_SAMD51/endstop_interrupts.h create mode 100644 Marlin/src/HAL/HAL_SAMD51/fastio_SAMD51.h create mode 100644 Marlin/src/HAL/HAL_SAMD51/inc/Conditionals_LCD.h create mode 100644 Marlin/src/HAL/HAL_SAMD51/inc/Conditionals_adv.h create mode 100644 Marlin/src/HAL/HAL_SAMD51/inc/Conditionals_post.h create mode 100644 Marlin/src/HAL/HAL_SAMD51/inc/SanityCheck.h create mode 100644 Marlin/src/HAL/HAL_SAMD51/persistent_store_eeprom.cpp create mode 100644 Marlin/src/HAL/HAL_SAMD51/pinsDebug.h create mode 100644 Marlin/src/HAL/HAL_SAMD51/spi_pins.h create mode 100644 Marlin/src/HAL/HAL_SAMD51/watchdog_SAMD51.cpp create mode 100644 Marlin/src/HAL/HAL_SAMD51/watchdog_SAMD51.h create mode 100644 Marlin/src/HAL/HAL_STM32/inc/Conditionals_LCD.h create mode 100644 Marlin/src/HAL/HAL_STM32/inc/Conditionals_adv.h create mode 100644 Marlin/src/HAL/HAL_STM32/inc/Conditionals_post.h rename Marlin/src/HAL/HAL_STM32/{ => inc}/SanityCheck.h (100%) create mode 100644 Marlin/src/HAL/HAL_STM32/persistent_store_sdcard.cpp create mode 100644 Marlin/src/HAL/HAL_STM32/pinsDebug_STM32GENERIC.h create mode 100644 Marlin/src/HAL/HAL_STM32/pinsDebug_STM32duino.h create mode 100644 Marlin/src/HAL/HAL_STM32/pins_Xref.h rename Marlin/src/HAL/HAL_STM32F1/{ => dogm}/u8g_com_stm32duino_fsmc.cpp (73%) rename Marlin/src/HAL/HAL_STM32F1/{ => dogm}/u8g_com_stm32duino_swspi.cpp (98%) create mode 100644 Marlin/src/HAL/HAL_STM32F1/inc/Conditionals_LCD.h create mode 100644 Marlin/src/HAL/HAL_STM32F1/inc/Conditionals_adv.h create mode 100644 Marlin/src/HAL/HAL_STM32F1/inc/Conditionals_post.h rename Marlin/src/HAL/HAL_STM32F1/{ => inc}/SanityCheck.h (100%) delete mode 100644 Marlin/src/HAL/HAL_STM32F4/EEPROM_Emul/eeprom_emul.cpp delete mode 100644 Marlin/src/HAL/HAL_STM32F4/EmulatedEeprom.cpp delete mode 100644 Marlin/src/HAL/HAL_STM32F4/HAL.cpp delete mode 100644 Marlin/src/HAL/HAL_STM32F4/HAL.h delete mode 100644 Marlin/src/HAL/HAL_STM32F4/HAL_Servo_STM32F4.cpp delete mode 100644 Marlin/src/HAL/HAL_STM32F4/fastio_STM32F4.h delete mode 100644 Marlin/src/HAL/HAL_STM32F4/persistent_store_eeprom.cpp delete mode 100644 Marlin/src/HAL/HAL_STM32F4/pinsDebug.h delete mode 100644 Marlin/src/HAL/HAL_STM32F7/EEPROM_Emul/eeprom_emul.h delete mode 100644 Marlin/src/HAL/HAL_STM32F7/EmulatedEeprom.cpp delete mode 100644 Marlin/src/HAL/HAL_STM32F7/HAL.cpp delete mode 100644 Marlin/src/HAL/HAL_STM32F7/HAL_spi_STM32F7.cpp delete mode 100644 Marlin/src/HAL/HAL_STM32F7/endstop_interrupts.h delete mode 100644 Marlin/src/HAL/HAL_STM32F7/pinsDebug.h delete mode 100644 Marlin/src/HAL/HAL_STM32F7/watchdog_STM32F7.cpp create mode 100644 Marlin/src/HAL/HAL_STM32_F4_F7/EmulatedEeprom.cpp create mode 100644 Marlin/src/HAL/HAL_STM32_F4_F7/HAL.cpp rename Marlin/src/HAL/{HAL_STM32F7 => HAL_STM32_F4_F7}/HAL.h (82%) rename Marlin/src/HAL/{HAL_STM32F7/HAL_Servo_STM32F7.cpp => HAL_STM32_F4_F7/HAL_Servo_STM32_F4_F7.cpp} (91%) rename Marlin/src/HAL/{HAL_STM32F4/HAL_Servo_STM32F4.h => HAL_STM32_F4_F7/HAL_Servo_STM32_F4_F7.h} (89%) rename Marlin/src/HAL/{HAL_STM32F4/HAL_spi_STM32F4.cpp => HAL_STM32_F4_F7/HAL_spi_STM32_F4_F7.cpp} (79%) create mode 100644 Marlin/src/HAL/HAL_STM32_F4_F7/HAL_timers_STM32_F4_F7.h create mode 100644 Marlin/src/HAL/HAL_STM32_F4_F7/README.md rename Marlin/src/HAL/{HAL_STM32F4 => HAL_STM32_F4_F7/STM32F4}/HAL_timers_STM32F4.cpp (75%) rename Marlin/src/HAL/{HAL_STM32F4 => HAL_STM32_F4_F7/STM32F4}/HAL_timers_STM32F4.h (82%) rename Marlin/src/HAL/{HAL_STM32F4 => HAL_STM32_F4_F7/STM32F4}/README.md (100%) rename Marlin/src/HAL/{HAL_STM32F7 => HAL_STM32_F4_F7/STM32F7}/HAL_timers_STM32F7.cpp (72%) rename Marlin/src/HAL/{HAL_STM32F7 => HAL_STM32_F4_F7/STM32F7}/HAL_timers_STM32F7.h (81%) rename Marlin/src/HAL/{HAL_STM32F7 => HAL_STM32_F4_F7/STM32F7}/README.md (75%) rename Marlin/src/HAL/{HAL_STM32F7 => HAL_STM32_F4_F7/STM32F7}/TMC2660.cpp (97%) rename Marlin/src/HAL/{HAL_STM32F7 => HAL_STM32_F4_F7/STM32F7}/TMC2660.h (99%) rename Marlin/src/HAL/{HAL_STM32F7/EEPROM_Emul => HAL_STM32_F4_F7}/eeprom_emul.cpp (74%) rename Marlin/src/HAL/{HAL_STM32F4/EEPROM_Emul => HAL_STM32_F4_F7}/eeprom_emul.h (64%) rename Marlin/src/HAL/{HAL_STM32F4 => HAL_STM32_F4_F7}/endstop_interrupts.h (100%) rename Marlin/src/HAL/{HAL_STM32F7/fastio_STM32F7.h => HAL_STM32_F4_F7/fastio_STM32_F4_F7.h} (79%) create mode 100644 Marlin/src/HAL/HAL_STM32_F4_F7/inc/Conditionals_LCD.h create mode 100644 Marlin/src/HAL/HAL_STM32_F4_F7/inc/Conditionals_adv.h create mode 100644 Marlin/src/HAL/HAL_STM32_F4_F7/inc/Conditionals_post.h rename Marlin/src/HAL/{HAL_STM32F7 => HAL_STM32_F4_F7/inc}/SanityCheck.h (87%) rename Marlin/src/HAL/{HAL_STM32F7 => HAL_STM32_F4_F7}/persistent_store_eeprom.cpp (91%) create mode 100644 Marlin/src/HAL/HAL_STM32_F4_F7/pinsDebug.h rename Marlin/src/HAL/{HAL_STM32F4 => HAL_STM32_F4_F7}/spi_pins.h (100%) rename Marlin/src/HAL/{HAL_STM32F4/watchdog_STM32F4.cpp => HAL_STM32_F4_F7/watchdog_STM32_F4_F7.cpp} (88%) rename Marlin/src/HAL/{HAL_STM32F4/watchdog_STM32F4.h => HAL_STM32_F4_F7/watchdog_STM32_F4_F7.h} (100%) create mode 100644 Marlin/src/HAL/HAL_TEENSY31_32/inc/Conditionals_LCD.h create mode 100644 Marlin/src/HAL/HAL_TEENSY31_32/inc/Conditionals_adv.h create mode 100644 Marlin/src/HAL/HAL_TEENSY31_32/inc/Conditionals_post.h rename Marlin/src/HAL/HAL_TEENSY31_32/{ => inc}/SanityCheck.h (100%) create mode 100644 Marlin/src/HAL/HAL_TEENSY35_36/inc/Conditionals_LCD.h create mode 100644 Marlin/src/HAL/HAL_TEENSY35_36/inc/Conditionals_adv.h create mode 100644 Marlin/src/HAL/HAL_TEENSY35_36/inc/Conditionals_post.h rename Marlin/src/HAL/HAL_TEENSY35_36/{ => inc}/SanityCheck.h (100%) delete mode 100644 Marlin/src/HAL/HAL_TEENSY35_36/persistent_store_impl.cpp rename Marlin/src/HAL/shared/{I2cEeprom.cpp => eeprom_i2c.cpp} (67%) rename Marlin/src/HAL/shared/{SpiEeprom.cpp => eeprom_spi.cpp} (99%) delete mode 100644 Marlin/src/core/minmax.h create mode 100644 Marlin/src/feature/touch/xpt2046.cpp create mode 100644 Marlin/src/feature/touch/xpt2046.h create mode 100644 Marlin/src/gcode/config/M575.cpp rename Marlin/src/{HAL/HAL_STM32F7/HAL_Servo_STM32F7.h => lcd/menu/game/brickout.h} (66%) create mode 100644 Marlin/src/lcd/menu/game/invaders.h create mode 100644 Marlin/src/lcd/menu/game/maze.h create mode 100644 Marlin/src/lcd/menu/game/snake.h rename Marlin/src/{HAL/HAL_STM32F4/SanityCheck.h => lcd/menu/game/types.h} (61%) create mode 100644 Marlin/src/module/thermistor/thermistor_512.h rename Marlin/src/pins/{ => esp32}/pins_ESP32.h (100%) rename Marlin/src/pins/{ => linux}/pins_RAMPS_LINUX.h (83%) rename Marlin/src/pins/{ => lpc1768}/pins_AZSMZ_MINI.h (100%) rename Marlin/src/pins/{pins_BIQU_SKR_V1.1.h => lpc1768/pins_BIGTREE_SKR_V1.1.h} (99%) rename Marlin/src/pins/{ => lpc1768}/pins_BIGTREE_SKR_V1.3.h (95%) rename Marlin/src/pins/{ => lpc1768}/pins_BIQU_B300_V1.0.h (95%) rename Marlin/src/pins/{ => lpc1768}/pins_BIQU_BQ111_A4.h (100%) create mode 100644 Marlin/src/pins/lpc1768/pins_GMARSH_X6_REV1.h rename Marlin/src/pins/{ => lpc1768}/pins_MKS_SBASE.h (91%) rename Marlin/src/pins/{ => lpc1768}/pins_MKS_SGEN_L.h (95%) rename Marlin/src/pins/{ => lpc1768}/pins_RAMPS_RE_ARM.h (90%) rename Marlin/src/pins/{ => lpc1768}/pins_SELENA_COMPACT.h (100%) rename Marlin/src/pins/{ => lpc1768}/pins_TH3D_EZBOARD.h (100%) rename Marlin/src/pins/{ => lpc1769}/pins_AZTEEG_X5_GT.h (96%) rename Marlin/src/pins/{ => lpc1769}/pins_AZTEEG_X5_MINI.h (99%) rename Marlin/src/pins/{ => lpc1769}/pins_AZTEEG_X5_MINI_WIFI.h (96%) rename Marlin/src/pins/{ => lpc1769}/pins_COHESION3D_MINI.h (100%) rename Marlin/src/pins/{ => lpc1769}/pins_COHESION3D_REMIX.h (100%) rename Marlin/src/pins/{ => lpc1769}/pins_MKS_SGEN.h (80%) rename Marlin/src/pins/{ => lpc1769}/pins_SMOOTHIEBOARD.h (100%) rename Marlin/src/pins/{ => mega}/pins_CHEAPTRONIC.h (100%) rename Marlin/src/pins/{ => mega}/pins_CHEAPTRONICv2.h (99%) rename Marlin/src/pins/{ => mega}/pins_CNCONTROLS_11.h (100%) rename Marlin/src/pins/{ => mega}/pins_CNCONTROLS_12.h (100%) rename Marlin/src/pins/{ => mega}/pins_EINSTART-S.h (84%) rename Marlin/src/pins/{ => mega}/pins_ELEFU_3.h (100%) rename Marlin/src/pins/{ => mega}/pins_GT2560_REV_A.h (99%) rename Marlin/src/pins/{ => mega}/pins_GT2560_REV_A_PLUS.h (100%) rename Marlin/src/pins/{ => mega}/pins_GT2560_V3.h (86%) rename Marlin/src/pins/{ => mega}/pins_GT2560_V3_A20.h (89%) rename Marlin/src/pins/{ => mega}/pins_GT2560_V3_MC2.h (100%) rename Marlin/src/pins/{ => mega}/pins_LEAPFROG.h (100%) rename Marlin/src/pins/{ => mega}/pins_MEGACONTROLLER.h (95%) rename Marlin/src/pins/{ => mega}/pins_MEGATRONICS.h (94%) rename Marlin/src/pins/{ => mega}/pins_MEGATRONICS_2.h (95%) rename Marlin/src/pins/{ => mega}/pins_MEGATRONICS_3.h (94%) rename Marlin/src/pins/{ => mega}/pins_MIGHTYBOARD_REVE.h (98%) rename Marlin/src/pins/{ => mega}/pins_MINITRONICS.h (98%) create mode 100644 Marlin/src/pins/mega/pins_OVERLORD.h rename Marlin/src/pins/{ => mega}/pins_SILVER_GATE.h (100%) create mode 100644 Marlin/src/pins/mega/pins_WANHAO_ONEPLUS.h delete mode 100644 Marlin/src/pins/pins_GTM32_PRO_VB.h rename Marlin/src/pins/{ => rambo}/pins_EINSY_RAMBO.h (97%) rename Marlin/src/pins/{ => rambo}/pins_EINSY_RETRO.h (97%) rename Marlin/src/pins/{ => rambo}/pins_MINIRAMBO.h (97%) rename Marlin/src/pins/{ => rambo}/pins_RAMBO.h (97%) rename Marlin/src/pins/{ => rambo}/pins_SCOOVO_X9H.h (100%) rename Marlin/src/pins/{ => ramps}/pins_3DRAG.h (91%) rename Marlin/src/pins/{ => ramps}/pins_AZTEEG_X3.h (93%) rename Marlin/src/pins/{ => ramps}/pins_AZTEEG_X3_PRO.h (93%) rename Marlin/src/pins/{ => ramps}/pins_BAM_DICE_DUE.h (90%) rename Marlin/src/pins/{ => ramps}/pins_BIQU_KFB_2.h (100%) rename Marlin/src/pins/{ => ramps}/pins_BQ_ZUM_MEGA_3D.h (93%) rename Marlin/src/pins/{ => ramps}/pins_DUPLICATOR_I3_PLUS.h (99%) rename Marlin/src/pins/{ => ramps}/pins_FELIX2.h (97%) rename Marlin/src/pins/{ => ramps}/pins_FORMBOT_RAPTOR.h (87%) rename Marlin/src/pins/{ => ramps}/pins_FORMBOT_RAPTOR2.h (80%) rename Marlin/src/pins/{ => ramps}/pins_FORMBOT_TREX2PLUS.h (90%) rename Marlin/src/pins/{ => ramps}/pins_FORMBOT_TREX3.h (88%) rename Marlin/src/pins/{ => ramps}/pins_FYSETC_F6_13.h (96%) rename Marlin/src/pins/{ => ramps}/pins_K8200.h (100%) rename Marlin/src/pins/{ => ramps}/pins_K8400.h (100%) rename Marlin/src/pins/{ => ramps}/pins_K8800.h (100%) rename Marlin/src/pins/{ => ramps}/pins_MAKEBOARD_MINI.h (86%) rename Marlin/src/pins/{ => ramps}/pins_MKS_BASE.h (91%) rename Marlin/src/pins/{ => ramps}/pins_MKS_BASE_14.h (100%) rename Marlin/src/pins/{ => ramps}/pins_MKS_BASE_15.h (100%) rename Marlin/src/pins/{ => ramps}/pins_MKS_BASE_HEROIC.h (100%) rename Marlin/src/pins/{ => ramps}/pins_MKS_GEN_13.h (98%) rename Marlin/src/pins/{ => ramps}/pins_MKS_GEN_L.h (100%) rename Marlin/src/pins/{ => ramps}/pins_RAMPS.h (85%) rename Marlin/src/pins/{ => ramps}/pins_RAMPS_13.h (100%) rename Marlin/src/pins/{ => ramps}/pins_RAMPS_CREALITY.h (100%) rename Marlin/src/pins/{ => ramps}/pins_RAMPS_DAGOMA.h (100%) rename Marlin/src/pins/{ => ramps}/pins_RAMPS_ENDER_4.h (100%) rename Marlin/src/pins/{ => ramps}/pins_RAMPS_OLD.h (84%) rename Marlin/src/pins/{ => ramps}/pins_RAMPS_PLUS.h (100%) rename Marlin/src/pins/{ => ramps}/pins_RIGIDBOARD.h (98%) rename Marlin/src/pins/{ => ramps}/pins_RIGIDBOARD_V2.h (99%) rename Marlin/src/pins/{ => ramps}/pins_RL200.h (100%) rename Marlin/src/pins/{ => ramps}/pins_RUMBA.h (95%) rename Marlin/src/pins/{ => ramps}/pins_RUMBA_RAISE3D.h (100%) rename Marlin/src/pins/{ => ramps}/pins_SAINSMART_2IN1.h (100%) rename Marlin/src/pins/{ => ramps}/pins_TRIGORILLA_13.h (100%) rename Marlin/src/pins/{ => ramps}/pins_TRIGORILLA_14.h (100%) rename Marlin/src/pins/{ => ramps}/pins_TRONXY_V3_1_0.h (99%) create mode 100644 Marlin/src/pins/ramps/pins_TT_OSCAR.h rename Marlin/src/pins/{ => ramps}/pins_ULTIMAIN_2.h (96%) rename Marlin/src/pins/{ => ramps}/pins_ULTIMAKER.h (95%) rename Marlin/src/pins/{ => ramps}/pins_ULTIMAKER_OLD.h (93%) rename Marlin/src/pins/{ => ramps}/pins_VORON.h (100%) rename Marlin/src/pins/{ => ramps}/pins_ZRIB_V20.h (100%) rename Marlin/src/pins/{ => ramps}/pins_Z_BOLT_X_SERIES.h (68%) rename Marlin/src/pins/{ => sam}/pins_ADSK.h (100%) rename Marlin/src/pins/{ => sam}/pins_ALLIGATOR_R2.h (100%) rename Marlin/src/pins/{ => sam}/pins_ARCHIM1.h (100%) rename Marlin/src/pins/{ => sam}/pins_ARCHIM2.h (97%) rename Marlin/src/pins/{ => sam}/pins_DUE3DOM.h (100%) rename Marlin/src/pins/{ => sam}/pins_DUE3DOM_MINI.h (100%) rename Marlin/src/pins/{ => sam}/pins_PRINTRBOARD_G2.h (100%) rename Marlin/src/pins/{ => sam}/pins_RADDS.h (99%) rename Marlin/src/pins/{ => sam}/pins_RAMPS4DUE.h (95%) rename Marlin/src/pins/{ => sam}/pins_RAMPS_DUO.h (91%) rename Marlin/src/pins/{ => sam}/pins_RAMPS_FD_V1.h (98%) rename Marlin/src/pins/{ => sam}/pins_RAMPS_FD_V2.h (100%) rename Marlin/src/pins/{ => sam}/pins_RAMPS_SMART.h (92%) rename Marlin/src/pins/{ => sam}/pins_RURAMPS4D_11.h (100%) rename Marlin/src/pins/{ => sam}/pins_RURAMPS4D_13.h (100%) rename Marlin/src/pins/{ => sam}/pins_ULTRATRONICS_PRO.h (100%) create mode 100644 Marlin/src/pins/samd/pins_AGCM4_RURAMPS4D_13.h rename Marlin/src/pins/{ => sanguino}/pins_ANET_10.h (100%) rename Marlin/src/pins/{ => sanguino}/pins_AZTEEG_X1.h (100%) rename Marlin/src/pins/{ => sanguino}/pins_GEN3_MONOLITHIC.h (100%) rename Marlin/src/pins/{ => sanguino}/pins_GEN3_PLUS.h (100%) rename Marlin/src/pins/{ => sanguino}/pins_GEN6.h (94%) rename Marlin/src/pins/{ => sanguino}/pins_GEN6_DELUXE.h (100%) rename Marlin/src/pins/{ => sanguino}/pins_GEN7_12.h (91%) rename Marlin/src/pins/{ => sanguino}/pins_GEN7_13.h (100%) rename Marlin/src/pins/{ => sanguino}/pins_GEN7_14.h (93%) rename Marlin/src/pins/{ => sanguino}/pins_GEN7_CUSTOM.h (94%) rename Marlin/src/pins/{ => sanguino}/pins_MELZI.h (100%) rename Marlin/src/pins/{ => sanguino}/pins_MELZI_CREALITY.h (100%) rename Marlin/src/pins/{ => sanguino}/pins_MELZI_MAKR3D.h (100%) rename Marlin/src/pins/{ => sanguino}/pins_MELZI_MALYAN.h (100%) rename Marlin/src/pins/{ => sanguino}/pins_MELZI_TRONXY.h (100%) rename Marlin/src/pins/{ => sanguino}/pins_OMCA.h (100%) rename Marlin/src/pins/{ => sanguino}/pins_OMCA_A.h (100%) rename Marlin/src/pins/{ => sanguino}/pins_SANGUINOLOLU_11.h (95%) rename Marlin/src/pins/{ => sanguino}/pins_SANGUINOLOLU_12.h (100%) rename Marlin/src/pins/{ => sanguino}/pins_SETHI.h (98%) rename Marlin/src/pins/{ => sanguino}/pins_STB_11.h (99%) rename Marlin/src/pins/{ => stm32}/pins_ARMED.h (61%) rename Marlin/src/pins/{ => stm32}/pins_BEAST.h (96%) create mode 100644 Marlin/src/pins/stm32/pins_BIGTREE_SKR_E3_DIP.h rename Marlin/src/pins/{ => stm32}/pins_BIGTREE_SKR_MINI_E3.h (90%) rename Marlin/src/pins/{ => stm32}/pins_BIGTREE_SKR_MINI_V1_1.h (93%) create mode 100644 Marlin/src/pins/stm32/pins_BIGTREE_SKR_PRO_V1.1.h rename Marlin/src/pins/{ => stm32}/pins_BLACK_STM32F407VE.h (94%) rename Marlin/src/pins/{ => stm32}/pins_CHITU3D.h (96%) rename Marlin/src/pins/{ => stm32}/pins_FYSETC_AIO_II.h (94%) rename Marlin/src/pins/{ => stm32}/pins_FYSETC_CHEETAH.h (94%) create mode 100644 Marlin/src/pins/stm32/pins_FYSETC_CHEETAH_V12.h create mode 100644 Marlin/src/pins/stm32/pins_GTM32_PRO_VB.h rename Marlin/src/pins/{ => stm32}/pins_JGAURORA_A5S_A1.h (60%) create mode 100644 Marlin/src/pins/stm32/pins_LONGER3D_LK.h rename Marlin/src/pins/{ => stm32}/pins_MALYAN_M200.h (98%) rename Marlin/src/pins/{ => stm32}/pins_MKS_ROBIN.h (86%) create mode 100644 Marlin/src/pins/stm32/pins_MKS_ROBIN_LITE.h rename Marlin/src/pins/{ => stm32}/pins_MKS_ROBIN_MINI.h (81%) rename Marlin/src/pins/{ => stm32}/pins_MKS_ROBIN_NANO.h (77%) rename Marlin/src/pins/{ => stm32}/pins_MORPHEUS.h (100%) rename Marlin/src/pins/{ => stm32}/pins_REMRAM_V1.h (96%) rename Marlin/src/pins/{ => stm32}/pins_RUMBA32.h (95%) rename Marlin/src/pins/{ => stm32}/pins_STEVAL.h (98%) rename Marlin/src/pins/{ => stm32}/pins_STM32F1R.h (96%) rename Marlin/src/pins/{ => stm32}/pins_STM32F4.h (95%) rename Marlin/src/pins/{ => stm32}/pins_STM3R_MINI.h (55%) rename Marlin/src/pins/{ => stm32}/pins_THE_BORG.h (95%) rename Marlin/src/pins/{ => teensy2}/pins_5DPRINT.h (100%) rename Marlin/src/pins/{ => teensy2}/pins_BRAINWAVE.h (100%) rename Marlin/src/pins/{ => teensy2}/pins_BRAINWAVE_PRO.h (100%) rename Marlin/src/pins/{ => teensy2}/pins_PRINTRBOARD.h (100%) rename Marlin/src/pins/{ => teensy2}/pins_PRINTRBOARD_REVF.h (100%) rename Marlin/src/pins/{ => teensy2}/pins_SAV_MKI.h (97%) rename Marlin/src/pins/{ => teensy2}/pins_TEENSY2.h (100%) rename Marlin/src/pins/{ => teensy2}/pins_TEENSYLU.h (100%) rename Marlin/src/pins/{ => teensy3}/pins_TEENSY31_32.h (52%) rename Marlin/src/pins/{ => teensy3}/pins_TEENSY35_36.h (100%) create mode 100644 config/examples/Alfawise/U20/Configuration.h create mode 100644 config/examples/Alfawise/U20/Configuration_adv.h create mode 100644 config/examples/Alfawise/U20/_Statusscreen.h delete mode 100644 config/examples/Creality/Ender-3/README.md create mode 100644 config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration.h create mode 100644 config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h create mode 100644 config/examples/FYSETC/Cheetah 1.2/base/Configuration.h rename config/examples/{Fysetc/CHEETAH => FYSETC/Cheetah 1.2/base}/Configuration_adv.h (99%) rename config/examples/{Fysetc/CHEETAH => FYSETC/Cheetah/BLTouch}/Configuration.h (95%) create mode 100644 config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h create mode 100644 config/examples/FYSETC/Cheetah/base/Configuration.h create mode 100644 config/examples/FYSETC/Cheetah/base/Configuration_adv.h create mode 100644 config/examples/Tevo/Michelangelo/Configuration.h create mode 100644 config/examples/Tevo/Michelangelo/Configuration_adv.h create mode 100644 config/examples/Tevo/Michelangelo/_Bootscreen.h create mode 100644 config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h create mode 100644 config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h create mode 100644 config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h create mode 100644 config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h create mode 100644 config/examples/Tevo/Tornado/_Bootscreen.h create mode 100644 config/examples/Wanhao/Duplicator i3 Mini/Configuration.h create mode 100644 config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index 82502ca12c..7059241fb8 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -201,8 +201,8 @@ // Displayed in the LCD "Ready" message #define CUSTOM_MACHINE_NAME "TM3D RaPtOr" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -339,7 +339,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -367,9 +374,9 @@ // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). // For the other hotends it is their distance from the extruder 0 hotend. -//#define HOTEND_OFFSET_X {0.0, 20.00} // (mm) relative X-offset for each nozzle -//#define HOTEND_OFFSET_Y {0.0, 5.00} // (mm) relative Y-offset for each nozzle -//#define HOTEND_OFFSET_Z {0.0, 0.00} // (mm) relative Z-offset for each nozzle +//#define HOTEND_OFFSET_X { 0.0, 20.00 } // (mm) relative X-offset for each nozzle +//#define HOTEND_OFFSET_Y { 0.0, 5.00 } // (mm) relative Y-offset for each nozzle +//#define HOTEND_OFFSET_Z { 0.0, 0.00 } // (mm) relative Z-offset for each nozzle // @section machine @@ -421,6 +428,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -457,9 +465,13 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ -#define TEMP_SENSOR_0 1 +#if ENABLED(RAPTOR2) + #define TEMP_SENSOR_0 61 +#else + #define TEMP_SENSOR_0 1 +#endif #define TEMP_SENSOR_1 0 #define TEMP_SENSOR_2 0 #define TEMP_SENSOR_3 0 @@ -588,7 +600,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1596,7 +1608,7 @@ // // M100 Free Memory Watcher // -#define M100_FREE_MEMORY_WATCHER // Add M100 (Free Memory Watcher) to debug memory usage +//#define M100_FREE_MEMORY_WATCHER // Add M100 (Free Memory Watcher) to debug memory usage // // G20/G21 Inch mode support @@ -1690,7 +1702,7 @@ // Specify positions as { X, Y, Z } #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)} - #define NOZZLE_CLEAN_END_POINT {100, 60, (Z_MIN_POS + 1)} + #define NOZZLE_CLEAN_END_POINT { 100, 60, (Z_MIN_POS + 1) } // Circular pattern radius #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5 @@ -1699,8 +1711,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1857,6 +1872,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -2084,31 +2107,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -2142,15 +2146,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -2163,6 +2158,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2188,17 +2225,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2294,8 +2338,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h index ea9413126f..692414a37a 100644 --- a/Marlin/Configuration_adv.h +++ b/Marlin/Configuration_adv.h @@ -654,6 +654,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -855,6 +856,9 @@ // Include a page of printer information in the LCD Main Menu #define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -1041,7 +1045,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1139,6 +1143,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1216,37 +1221,19 @@ #define LIN_ADVANCE #endif #if ENABLED(LIN_ADVANCE) - #define LIN_ADVANCE_K 0.0 // Unit: mm compression per 1mm/s extruder speed - //#define LA_DEBUG // If enabled, this will generate debug information output over USB. + //#define EXTRA_LIN_ADVANCE_K // Enable for second linear advance constants + #define LIN_ADVANCE_K 0.00 // Unit: mm compression per 1mm/s extruder speed + //#define LA_DEBUG // If enabled, this will generate debug information output over USB. #endif // @section leveling -#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL) +#if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL) // Override the mesh area if the automatic (max) area is too large - #if( (X_PROBE_OFFSET_FROM_EXTRUDER + (MIN_PROBE_EDGE + MESH_INSET)) > 0 ) - #define MESH_MIN_X (X_PROBE_OFFSET_FROM_EXTRUDER + MIN_PROBE_EDGE + MESH_INSET) - #else - #define MESH_MIN_X 10 - #endif - - #if( (X_BED_SIZE + X_PROBE_OFFSET_FROM_EXTRUDER - 10) < X_BED_SIZE) - #define MESH_MAX_X (X_BED_SIZE + X_PROBE_OFFSET_FROM_EXTRUDER - (MIN_PROBE_EDGE + MESH_INSET)) - #else - #define MESH_MAX_X (X_BED_SIZE - 10) - #endif - - #if ( (Y_PROBE_OFFSET_FROM_EXTRUDER + 10) > 5 ) - #define MESH_MIN_Y (Y_PROBE_OFFSET_FROM_EXTRUDER + MIN_PROBE_EDGE + MESH_INSET) - #else - #define MESH_MIN_Y 25 - #endif - - #if( (Y_BED_SIZE + Y_PROBE_OFFSET_FROM_EXTRUDER - 10) < Y_BED_SIZE) - #define MESH_MAX_Y (Y_BED_SIZE + Y_PROBE_OFFSET_FROM_EXTRUDER - 10) - #else - #define MESH_MAX_Y (Y_BED_SIZE - Y_PROBE_OFFSET_FROM_EXTRUDER - (MIN_PROBE_EDGE + MESH_INSET)) - #endif + //#define MESH_MIN_X MESH_INSET + //#define MESH_MIN_Y MESH_INSET + //#define MESH_MAX_X X_BED_SIZE - (MESH_INSET) + //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET) #endif /** @@ -1388,6 +1375,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1773,6 +1763,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2465,6 +2458,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/Marlin/src/HAL/HAL_STM32F7/watchdog_STM32F7.h b/Marlin/src/HAL/HAL.h similarity index 91% rename from Marlin/src/HAL/HAL_STM32F7/watchdog_STM32F7.h rename to Marlin/src/HAL/HAL.h index cc02fda24f..f3946902c8 100644 --- a/Marlin/src/HAL/HAL_STM32F7/watchdog_STM32F7.h +++ b/Marlin/src/HAL/HAL.h @@ -21,7 +21,6 @@ */ #pragma once -extern IWDG_HandleTypeDef hiwdg; +#include "platforms.h" -void watchdog_init(); -void watchdog_reset(); +#include HAL_PATH(.,HAL.h) diff --git a/Marlin/src/HAL/HAL_AVR/HAL.cpp b/Marlin/src/HAL/HAL_AVR/HAL.cpp index adc441cb61..47cf969959 100644 --- a/Marlin/src/HAL/HAL_AVR/HAL.cpp +++ b/Marlin/src/HAL/HAL_AVR/HAL.cpp @@ -22,64 +22,33 @@ #ifdef __AVR__ -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - #include "../../inc/MarlinConfig.h" #include "HAL.h" -// -------------------------------------------------------------------------- -// Externals -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Local defines -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Types -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Variables -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- +// ------------------------ // Public Variables -// -------------------------------------------------------------------------- +// ------------------------ //uint8_t MCUSR; -// -------------------------------------------------------------------------- -// Private Variables -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Function prototypes -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Private functions -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- +// ------------------------ // Public functions -// -------------------------------------------------------------------------- +// ------------------------ void HAL_init(void) { // Init Servo Pins - #if PIN_EXISTS(SERVO0) - OUT_WRITE(SERVO0_PIN, LOW); + #define INIT_SERVO(N) OUT_WRITE(SERVO##N##_PIN, LOW) + #if HAS_SERVO_0 + INIT_SERVO(0); #endif - #if PIN_EXISTS(SERVO1) - OUT_WRITE(SERVO1_PIN, LOW); + #if HAS_SERVO_1 + INIT_SERVO(1); #endif - #if PIN_EXISTS(SERVO2) - OUT_WRITE(SERVO2_PIN, LOW); + #if HAS_SERVO_2 + INIT_SERVO(2); #endif - #if PIN_EXISTS(SERVO3) - OUT_WRITE(SERVO3_PIN, LOW); + #if HAS_SERVO_3 + INIT_SERVO(3); #endif } diff --git a/Marlin/src/HAL/HAL_AVR/HAL.h b/Marlin/src/HAL/HAL_AVR/HAL.h index 38405e9441..8912b24eb4 100644 --- a/Marlin/src/HAL/HAL_AVR/HAL.h +++ b/Marlin/src/HAL/HAL_AVR/HAL.h @@ -18,12 +18,6 @@ */ #pragma once -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - -#include - #include "../shared/Marduino.h" #include "../shared/HAL_SPI.h" #include "fastio_AVR.h" @@ -33,18 +27,20 @@ #ifdef USBCON #include "HardwareSerial.h" #else + #define HardwareSerial_h // Hack to prevent HardwareSerial.h header inclusion #include "MarlinSerial.h" #endif +#include #include #include #include #include #include -// -------------------------------------------------------------------------- +// ------------------------ // Defines -// -------------------------------------------------------------------------- +// ------------------------ //#define analogInputToDigitalPin(IO) IO @@ -59,9 +55,9 @@ // On AVR this is in math.h? //#define square(x) ((x)*(x)) -// -------------------------------------------------------------------------- +// ------------------------ // Types -// -------------------------------------------------------------------------- +// ------------------------ typedef uint16_t hal_timer_t; #define HAL_TIMER_TYPE_MAX 0xFFFF @@ -71,9 +67,9 @@ typedef int8_t pin_t; #define SHARED_SERVOS HAS_SERVOS #define HAL_SERVO_LIB Servo -// -------------------------------------------------------------------------- +// ------------------------ // Public Variables -// -------------------------------------------------------------------------- +// ------------------------ //extern uint8_t MCUSR; @@ -105,9 +101,9 @@ typedef int8_t pin_t; #endif #endif -// -------------------------------------------------------------------------- +// ------------------------ // Public functions -// -------------------------------------------------------------------------- +// ------------------------ void HAL_init(void); diff --git a/Marlin/src/HAL/HAL_AVR/HAL_spi_AVR.cpp b/Marlin/src/HAL/HAL_AVR/HAL_spi_AVR.cpp index 0350847a61..1379207bf0 100644 --- a/Marlin/src/HAL/HAL_AVR/HAL_spi_AVR.cpp +++ b/Marlin/src/HAL/HAL_AVR/HAL_spi_AVR.cpp @@ -31,10 +31,6 @@ #ifdef __AVR__ -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - #include "../../inc/MarlinConfig.h" void spiBegin(void) { @@ -55,11 +51,11 @@ void spiBegin(void) { #endif } -#if DISABLED(SOFTWARE_SPI, FORCE_SOFT_SPI) +#if NONE(SOFTWARE_SPI, FORCE_SOFT_SPI) - //------------------------------------------------------------------------------ + // ------------------------ // Hardware SPI - //------------------------------------------------------------------------------ + // ------------------------ // make sure SPCR rate is in expected bits #if (SPR0 != 0 || SPR1 != 1) @@ -181,9 +177,9 @@ void spiBegin(void) { #else // SOFTWARE_SPI || FORCE_SOFT_SPI - //------------------------------------------------------------------------------ + // ------------------------ // Software SPI - //------------------------------------------------------------------------------ + // ------------------------ // nop to tune soft SPI timing #define nop asm volatile ("\tnop\n") diff --git a/Marlin/src/HAL/HAL_AVR/MarlinSerial.h b/Marlin/src/HAL/HAL_AVR/MarlinSerial.h index 8849212d97..f3e2086b2c 100644 --- a/Marlin/src/HAL/HAL_AVR/MarlinSerial.h +++ b/Marlin/src/HAL/HAL_AVR/MarlinSerial.h @@ -275,7 +275,6 @@ #endif // !USBCON - #ifdef INTERNAL_SERIAL_PORT template struct MarlinInternalSerialCfg { diff --git a/Marlin/src/HAL/HAL_AVR/ServoTimers.h b/Marlin/src/HAL/HAL_AVR/ServoTimers.h index 07d3070297..4991caefe6 100644 --- a/Marlin/src/HAL/HAL_AVR/ServoTimers.h +++ b/Marlin/src/HAL/HAL_AVR/ServoTimers.h @@ -53,8 +53,8 @@ * -------------------- */ -#define TRIM_DURATION 2 // compensation ticks to trim adjust for digitalWrite delays -#define PRESCALER 8 // timer prescaler +#define TRIM_DURATION 2 // compensation ticks to trim adjust for digitalWrite delays +#define SERVO_TIMER_PRESCALER 8 // timer prescaler // Say which 16 bit timers can be used and in what order #if defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__) diff --git a/Marlin/src/HAL/HAL_AVR/endstop_interrupts.h b/Marlin/src/HAL/HAL_AVR/endstop_interrupts.h index 4446367d15..c313f95ced 100644 --- a/Marlin/src/HAL/HAL_AVR/endstop_interrupts.h +++ b/Marlin/src/HAL/HAL_AVR/endstop_interrupts.h @@ -36,7 +36,6 @@ * (Located in Marlin/buildroot/share/pin_interrupt_test/pin_interrupt_test.ino) */ -#include "../../core/macros.h" #include "../../module/endstops.h" #include diff --git a/Marlin/src/HAL/HAL_AVR/fastio_1280.h b/Marlin/src/HAL/HAL_AVR/fastio/fastio_1280.h similarity index 99% rename from Marlin/src/HAL/HAL_AVR/fastio_1280.h rename to Marlin/src/HAL/HAL_AVR/fastio/fastio_1280.h index 84ceffcda0..ac2b650119 100644 --- a/Marlin/src/HAL/HAL_AVR/fastio_1280.h +++ b/Marlin/src/HAL/HAL_AVR/fastio/fastio_1280.h @@ -29,7 +29,7 @@ * Logical Pin : 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 | 78 79 80 xx xx 84 85 71 70 xx xx xx xx xx 81 82 83 xx xx 72 72 75 76 77 74 xx xx xx xx xx */ -#include "fastio_AVR.h" +#include "../fastio_AVR.h" // change for your board #define DEBUG_LED DIO21 diff --git a/Marlin/src/HAL/HAL_AVR/fastio_1281.h b/Marlin/src/HAL/HAL_AVR/fastio/fastio_1281.h similarity index 99% rename from Marlin/src/HAL/HAL_AVR/fastio_1281.h rename to Marlin/src/HAL/HAL_AVR/fastio/fastio_1281.h index 153d1fd7d2..e3501f4849 100644 --- a/Marlin/src/HAL/HAL_AVR/fastio_1281.h +++ b/Marlin/src/HAL/HAL_AVR/fastio/fastio_1281.h @@ -28,7 +28,7 @@ * Port: A0 A1 A2 A3 A4 A5 A6 A7 B0 B1 B2 B3 B4 B5 B6 B7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 E0 E1 E2 E3 E4 E5 E6 E7 F0 F1 F2 F3 F4 F5 F6 F7 G0 G1 G2 G3 G4 G5 */ -#include "fastio_AVR.h" +#include "../fastio_AVR.h" // change for your board #define DEBUG_LED DIO46 diff --git a/Marlin/src/HAL/HAL_AVR/fastio_168.h b/Marlin/src/HAL/HAL_AVR/fastio/fastio_168.h similarity index 99% rename from Marlin/src/HAL/HAL_AVR/fastio_168.h rename to Marlin/src/HAL/HAL_AVR/fastio/fastio_168.h index 7e5a1ec795..32db8cae0c 100644 --- a/Marlin/src/HAL/HAL_AVR/fastio_168.h +++ b/Marlin/src/HAL/HAL_AVR/fastio/fastio_168.h @@ -28,7 +28,7 @@ * Port: B0 B1 B2 B3 B4 B5 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 */ -#include "fastio_AVR.h" +#include "../fastio_AVR.h" #define DEBUG_LED AIO5 diff --git a/Marlin/src/HAL/HAL_AVR/fastio_644.h b/Marlin/src/HAL/HAL_AVR/fastio/fastio_644.h similarity index 99% rename from Marlin/src/HAL/HAL_AVR/fastio_644.h rename to Marlin/src/HAL/HAL_AVR/fastio/fastio_644.h index f62a0a35b4..582c76f7e4 100644 --- a/Marlin/src/HAL/HAL_AVR/fastio_644.h +++ b/Marlin/src/HAL/HAL_AVR/fastio/fastio_644.h @@ -54,7 +54,7 @@ * +--------+ */ -#include "fastio_AVR.h" +#include "../fastio_AVR.h" #define DEBUG_LED DIO0 diff --git a/Marlin/src/HAL/HAL_AVR/fastio_AT90USB.h b/Marlin/src/HAL/HAL_AVR/fastio/fastio_AT90USB.h similarity index 99% rename from Marlin/src/HAL/HAL_AVR/fastio_AT90USB.h rename to Marlin/src/HAL/HAL_AVR/fastio/fastio_AT90USB.h index c7bf5f6b5a..bd37f05990 100644 --- a/Marlin/src/HAL/HAL_AVR/fastio_AT90USB.h +++ b/Marlin/src/HAL/HAL_AVR/fastio/fastio_AT90USB.h @@ -29,7 +29,7 @@ * The logical pins 46 and 47 are not supported by Teensyduino, but are supported below as E2 and E3 */ -#include "fastio_AVR.h" +#include "../fastio_AVR.h" // change for your board #define DEBUG_LED DIO31 /* led D5 red */ diff --git a/Marlin/src/HAL/HAL_AVR/fastio_AVR.h b/Marlin/src/HAL/HAL_AVR/fastio_AVR.h index 1f2e820bdc..501a7cdf06 100644 --- a/Marlin/src/HAL/HAL_AVR/fastio_AVR.h +++ b/Marlin/src/HAL/HAL_AVR/fastio_AVR.h @@ -27,8 +27,6 @@ * Contributed by Triffid_Hunter and modified by Kliment, thinkyhead, Bob-the-Kuhn, et.al. */ -#include "../../core/macros.h" - #include #define AVR_AT90USB1286_FAMILY (defined(__AVR_AT90USB1287__) || defined(__AVR_AT90USB1286__) || defined(__AVR_AT90USB1286P__) || defined(__AVR_AT90USB646__) || defined(__AVR_AT90USB646P__) || defined(__AVR_AT90USB647__)) @@ -41,15 +39,15 @@ * Include Ports and Functions */ #if AVR_ATmega328_FAMILY - #include "fastio_168.h" + #include "fastio/fastio_168.h" #elif AVR_ATmega1284_FAMILY - #include "fastio_644.h" + #include "fastio/fastio_644.h" #elif AVR_ATmega2560_FAMILY - #include "fastio_1280.h" + #include "fastio/fastio_1280.h" #elif AVR_AT90USB1286_FAMILY - #include "fastio_AT90USB.h" + #include "fastio/fastio_AT90USB.h" #elif AVR_ATmega2561_FAMILY - #include "fastio_1281.h" + #include "fastio/fastio_1281.h" #else #error "No FastIO definition for the selected AVR Board." #endif @@ -274,6 +272,8 @@ enum ClockSource2 : char { #define SET_FOCB(T,V) SET_FOC(T,B,V) #define SET_FOCC(T,V) SET_FOC(T,C,V) +#if 0 + /** * PWM availability macros */ @@ -337,6 +337,8 @@ enum ClockSource2 : char { #define PWM_CHK(P) (PWM_CHK_HEATER(P) || PWM_CHK_SERVO(P) || PWM_CHK_MOTOR_CURRENT(P) || PWM_CHK_FAN_A(P) || PWM_CHK_FAN_B(P)) +#endif // PWM_CHK is not used in Marlin + // define which hardware PWMs are available for the current CPU // all timer 1 PWMS deleted from this list because they are never available #if AVR_ATmega2560_FAMILY diff --git a/Marlin/src/HAL/HAL_AVR/inc/Conditionals_LCD.h b/Marlin/src/HAL/HAL_AVR/inc/Conditionals_LCD.h new file mode 100644 index 0000000000..85f26f4016 --- /dev/null +++ b/Marlin/src/HAL/HAL_AVR/inc/Conditionals_LCD.h @@ -0,0 +1,22 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once diff --git a/Marlin/src/HAL/HAL_AVR/inc/Conditionals_adv.h b/Marlin/src/HAL/HAL_AVR/inc/Conditionals_adv.h new file mode 100644 index 0000000000..85f26f4016 --- /dev/null +++ b/Marlin/src/HAL/HAL_AVR/inc/Conditionals_adv.h @@ -0,0 +1,22 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once diff --git a/Marlin/src/HAL/HAL_AVR/inc/Conditionals_post.h b/Marlin/src/HAL/HAL_AVR/inc/Conditionals_post.h new file mode 100644 index 0000000000..85f26f4016 --- /dev/null +++ b/Marlin/src/HAL/HAL_AVR/inc/Conditionals_post.h @@ -0,0 +1,22 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once diff --git a/Marlin/src/HAL/HAL_AVR/SanityCheck.h b/Marlin/src/HAL/HAL_AVR/inc/SanityCheck.h similarity index 100% rename from Marlin/src/HAL/HAL_AVR/SanityCheck.h rename to Marlin/src/HAL/HAL_AVR/inc/SanityCheck.h diff --git a/Marlin/src/HAL/HAL_AVR/pinsDebug.h b/Marlin/src/HAL/HAL_AVR/pinsDebug.h index 4737c3517a..fa70180947 100644 --- a/Marlin/src/HAL/HAL_AVR/pinsDebug.h +++ b/Marlin/src/HAL/HAL_AVR/pinsDebug.h @@ -353,6 +353,8 @@ static void pwm_details(uint8_t pin) { timer_prefix(0, 'A', 3); #endif } + #else + UNUSED(print_is_also_tied); #endif } // pwm_details @@ -400,4 +402,4 @@ static void pwm_details(uint8_t pin) { #endif -#define PRINT_PIN(p) do {sprintf_P(buffer, PSTR("%3d "), p); SERIAL_ECHO(buffer);} while (0) +#define PRINT_PIN(p) do{ sprintf_P(buffer, PSTR("%3d "), p); SERIAL_ECHO(buffer); }while(0) diff --git a/Marlin/src/HAL/HAL_AVR/pinsDebug_plus_70.h b/Marlin/src/HAL/HAL_AVR/pinsDebug_plus_70.h index 2a2a7bce8a..e5bb82f226 100644 --- a/Marlin/src/HAL/HAL_AVR/pinsDebug_plus_70.h +++ b/Marlin/src/HAL/HAL_AVR/pinsDebug_plus_70.h @@ -47,7 +47,7 @@ const uint8_t PROGMEM digital_pin_to_port_PGM_plus_70[] = { // PORTLIST - // ------------------------------------------- + // ------------------------ PE , // PE 0 ** 0 ** USART0_RX PE , // PE 1 ** 1 ** USART0_TX PE , // PE 4 ** 2 ** PWM2 @@ -140,7 +140,7 @@ const uint8_t PROGMEM digital_pin_to_port_PGM_plus_70[] = { const uint8_t PROGMEM digital_pin_to_bit_mask_PGM_plus_70[] = { // PIN IN PORT - // ------------------------------------------- + // ------------------------ _BV( 0 ) , // PE 0 ** 0 ** USART0_RX _BV( 1 ) , // PE 1 ** 1 ** USART0_TX _BV( 4 ) , // PE 4 ** 2 ** PWM2 @@ -234,7 +234,7 @@ const uint8_t PROGMEM digital_pin_to_bit_mask_PGM_plus_70[] = { const uint8_t PROGMEM digital_pin_to_timer_PGM_plus_70[] = { // TIMERS - // ------------------------------------------- + // ------------------------ NOT_ON_TIMER , // PE 0 ** 0 ** USART0_RX NOT_ON_TIMER , // PE 1 ** 1 ** USART0_TX TIMER3B , // PE 4 ** 2 ** PWM2 diff --git a/Marlin/src/HAL/HAL_DUE/EepromEmulation_Due.cpp b/Marlin/src/HAL/HAL_DUE/EepromEmulation_Due.cpp index 07f746a17d..231e4cc048 100644 --- a/Marlin/src/HAL/HAL_DUE/EepromEmulation_Due.cpp +++ b/Marlin/src/HAL/HAL_DUE/EepromEmulation_Due.cpp @@ -31,12 +31,12 @@ #ifdef ARDUINO_ARCH_SAM -#include "../shared/persistent_store_api.h" #include "../../inc/MarlinConfig.h" -#if ENABLED(EEPROM_SETTINGS) && DISABLED(I2C_EEPROM, SPI_EEPROM) +#if ENABLED(EEPROM_SETTINGS) && NONE(I2C_EEPROM, SPI_EEPROM) #include "../shared/Marduino.h" +#include "../shared/persistent_store_api.h" #define EEPROMSize 4096 #define PagesPerGroup 128 diff --git a/Marlin/src/HAL/HAL_DUE/HAL.cpp b/Marlin/src/HAL/HAL_DUE/HAL.cpp index dfe42f6ca3..c98dbbc07c 100644 --- a/Marlin/src/HAL/HAL_DUE/HAL.cpp +++ b/Marlin/src/HAL/HAL_DUE/HAL.cpp @@ -25,53 +25,21 @@ #ifdef ARDUINO_ARCH_SAM -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - #include "../../inc/MarlinConfig.h" #include "HAL.h" #include #include "usb/usb_task.h" -// -------------------------------------------------------------------------- -// Externals -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Local defines -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Types -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Variables -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- +// ------------------------ // Public Variables -// -------------------------------------------------------------------------- +// ------------------------ uint16_t HAL_adc_result; -// -------------------------------------------------------------------------- -// Private Variables -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Function prototypes -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Private functions -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- +// ------------------------ // Public functions -// -------------------------------------------------------------------------- +// ------------------------ // HAL initialization task void HAL_init(void) { @@ -122,9 +90,9 @@ int freeMemory() { return (int)&free_memory - (heap_end ? heap_end : (int)&_ebss); } -// -------------------------------------------------------------------------- +// ------------------------ // ADC -// -------------------------------------------------------------------------- +// ------------------------ void HAL_adc_start_conversion(const uint8_t adc_pin) { HAL_adc_result = analogRead(adc_pin); diff --git a/Marlin/src/HAL/HAL_DUE/HAL.h b/Marlin/src/HAL/HAL_DUE/HAL.h index 9430769734..40a0241905 100644 --- a/Marlin/src/HAL/HAL_DUE/HAL.h +++ b/Marlin/src/HAL/HAL_DUE/HAL.h @@ -68,10 +68,6 @@ #define strncpy_P(dest, src, num) strncpy((dest), (src), (num)) #endif -#ifndef vsnprintf_P - #define vsnprintf_P vsnprintf -#endif - // Fix bug in pgm_read_ptr #undef pgm_read_ptr #define pgm_read_ptr(addr) (*((void**)(addr))) diff --git a/Marlin/src/HAL/HAL_DUE/HAL_spi_Due.cpp b/Marlin/src/HAL/HAL_DUE/HAL_spi_Due.cpp index 82eae9b01e..94f90670c0 100644 --- a/Marlin/src/HAL/HAL_DUE/HAL_spi_Due.cpp +++ b/Marlin/src/HAL/HAL_DUE/HAL_spi_Due.cpp @@ -37,27 +37,18 @@ #ifdef ARDUINO_ARCH_SAM -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - #include "../../inc/MarlinConfig.h" #include "../shared/Delay.h" -// -------------------------------------------------------------------------- -// Public Variables -// -------------------------------------------------------------------------- - - -// -------------------------------------------------------------------------- +// ------------------------ // Public functions -// -------------------------------------------------------------------------- +// ------------------------ #if EITHER(DUE_SOFTWARE_SPI, FORCE_SOFT_SPI) - // -------------------------------------------------------------------------- - // software SPI - // -------------------------------------------------------------------------- + // ------------------------ + // Software SPI + // ------------------------ // Make sure GCC optimizes this file. // Note that this line triggers a bug in GCC which is fixed by casting. @@ -551,9 +542,9 @@ // slave selects controlled by SPI controller // doesn't support changing SPI speeds for SD card - // -------------------------------------------------------------------------- + // ------------------------ // hardware SPI - // -------------------------------------------------------------------------- + // ------------------------ static bool spiInitialized = false; void spiInit(uint8_t spiRate) { diff --git a/Marlin/src/HAL/HAL_DUE/HAL_timers_Due.cpp b/Marlin/src/HAL/HAL_DUE/HAL_timers_Due.cpp index df51c22d60..64ca0ac0f1 100644 --- a/Marlin/src/HAL/HAL_DUE/HAL_timers_Due.cpp +++ b/Marlin/src/HAL/HAL_DUE/HAL_timers_Due.cpp @@ -28,36 +28,23 @@ #ifdef ARDUINO_ARCH_SAM -// -------------------------------------------------------------------------- +// ------------------------ // Includes -// -------------------------------------------------------------------------- +// ------------------------ #include "../../inc/MarlinConfig.h" #include "HAL.h" #include "HAL_timers_Due.h" -// -------------------------------------------------------------------------- -// Externals -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- +// ------------------------ // Local defines -// -------------------------------------------------------------------------- +// ------------------------ #define NUM_HARDWARE_TIMERS 9 -// -------------------------------------------------------------------------- -// Types -// -------------------------------------------------------------------------- - - -// -------------------------------------------------------------------------- -// Public Variables -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- +// ------------------------ // Private Variables -// -------------------------------------------------------------------------- +// ------------------------ const tTimerConfig TimerConfig [NUM_HARDWARE_TIMERS] = { { TC0, 0, TC0_IRQn, 3}, // 0 - [servo timer5] @@ -71,17 +58,9 @@ const tTimerConfig TimerConfig [NUM_HARDWARE_TIMERS] = { { TC2, 2, TC8_IRQn, 0}, // 8 }; -// -------------------------------------------------------------------------- -// Function prototypes -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Private functions -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- +// ------------------------ // Public functions -// -------------------------------------------------------------------------- +// ------------------------ /* Timer_clock1: Prescaler 2 -> 42MHz diff --git a/Marlin/src/HAL/HAL_DUE/HAL_timers_Due.h b/Marlin/src/HAL/HAL_DUE/HAL_timers_Due.h index 2c758f3a11..ba1eccb2f9 100644 --- a/Marlin/src/HAL/HAL_DUE/HAL_timers_Due.h +++ b/Marlin/src/HAL/HAL_DUE/HAL_timers_Due.h @@ -26,15 +26,11 @@ * For ARDUINO_ARCH_SAM */ -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - #include -// -------------------------------------------------------------------------- +// ------------------------ // Defines -// -------------------------------------------------------------------------- +// ------------------------ #define FORCE_INLINE __attribute__((always_inline)) inline @@ -69,9 +65,9 @@ typedef uint32_t hal_timer_t; #define HAL_TEMP_TIMER_ISR() void TC4_Handler() #define HAL_TONE_TIMER_ISR() void TC6_Handler() -// -------------------------------------------------------------------------- +// ------------------------ // Types -// -------------------------------------------------------------------------- +// ------------------------ typedef struct { Tc *pTimerRegs; @@ -80,15 +76,15 @@ typedef struct { uint8_t priority; } tTimerConfig; -// -------------------------------------------------------------------------- +// ------------------------ // Public Variables -// -------------------------------------------------------------------------- +// ------------------------ extern const tTimerConfig TimerConfig[]; -// -------------------------------------------------------------------------- +// ------------------------ // Public functions -// -------------------------------------------------------------------------- +// ------------------------ void HAL_timer_start(const uint8_t timer_num, const uint32_t frequency); diff --git a/Marlin/src/HAL/HAL_DUE/ServoTimers.h b/Marlin/src/HAL/HAL_DUE/ServoTimers.h index 84129ef2b6..c32c938253 100644 --- a/Marlin/src/HAL/HAL_DUE/ServoTimers.h +++ b/Marlin/src/HAL/HAL_DUE/ServoTimers.h @@ -36,8 +36,8 @@ //!#define _useTimer4 #define _useTimer5 -#define TRIM_DURATION 2 // compensation ticks to trim adjust for digitalWrite delays -#define PRESCALER 32 // timer prescaler +#define TRIM_DURATION 2 // compensation ticks to trim adjust for digitalWrite delays +#define SERVO_TIMER_PRESCALER 32 // timer prescaler /* TC0, chan 0 => TC0_Handler diff --git a/Marlin/src/HAL/HAL_DUE/Servo_Due.cpp b/Marlin/src/HAL/HAL_DUE/Servo_Due.cpp index 2dd9d4c45e..a80d0c4f0d 100644 --- a/Marlin/src/HAL/HAL_DUE/Servo_Due.cpp +++ b/Marlin/src/HAL/HAL_DUE/Servo_Due.cpp @@ -50,9 +50,9 @@ static volatile int8_t Channel[_Nbr_16timers]; // counter for the servo being pulsed for each timer (or -1 if refresh interval) -//------------------------------------------------------------------------------ +// ------------------------ /// Interrupt handler for the TC0 channel 1. -//------------------------------------------------------------------------------ +// ------------------------ void Servo_Handler(timer16_Sequence_t timer, Tc *pTc, uint8_t channel); #ifdef _useTimer1 @@ -137,7 +137,7 @@ void initISR(timer16_Sequence_t timer) { #endif } -void finISR(timer16_Sequence_t timer) { +void finISR(timer16_Sequence_t) { #ifdef _useTimer1 TC_Stop(TC_FOR_TIMER1, CHANNEL_FOR_TIMER1); #endif diff --git a/Marlin/src/HAL/HAL_DUE/Tone.cpp b/Marlin/src/HAL/HAL_DUE/Tone.cpp index f7549c4472..b3d7e21698 100644 --- a/Marlin/src/HAL/HAL_DUE/Tone.cpp +++ b/Marlin/src/HAL/HAL_DUE/Tone.cpp @@ -5,6 +5,8 @@ * Based on Sprinter and grbl. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm * + * SAMD51 HAL developed by Giuliano Zaro (AKA GMagician) + * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation, either version 3 of the License, or diff --git a/Marlin/src/HAL/HAL_DUE/u8g_com_HAL_DUE_shared_hw_spi.cpp b/Marlin/src/HAL/HAL_DUE/dogm/u8g_com_HAL_DUE_shared_hw_spi.cpp similarity index 65% rename from Marlin/src/HAL/HAL_DUE/u8g_com_HAL_DUE_shared_hw_spi.cpp rename to Marlin/src/HAL/HAL_DUE/dogm/u8g_com_HAL_DUE_shared_hw_spi.cpp index f90d24dae0..8f9f745723 100644 --- a/Marlin/src/HAL/HAL_DUE/u8g_com_HAL_DUE_shared_hw_spi.cpp +++ b/Marlin/src/HAL/HAL_DUE/dogm/u8g_com_HAL_DUE_shared_hw_spi.cpp @@ -21,58 +21,57 @@ */ -/* - - based on u8g_com_msp430_hw_spi.c - - Universal 8bit Graphics Library - - Copyright (c) 2012, olikraus@gmail.com - All rights reserved. - - Redistribution and use in source and binary forms, with or without modification, - are permitted provided that the following conditions are met: - - * Redistributions of source code must retain the above copyright notice, this list - of conditions and the following disclaimer. - - * Redistributions in binary form must reproduce the above copyright notice, this - list of conditions and the following disclaimer in the documentation and/or other - materials provided with the distribution. - - THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND - CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, - INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF - MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE - DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR - CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, - SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT - NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; - LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER - CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, - STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) - ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF - ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - -*/ +/** + * Based on u8g_com_msp430_hw_spi.c + * + * Universal 8bit Graphics Library + * + * Copyright (c) 2012, olikraus@gmail.com + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * + * * Redistributions of source code must retain the above copyright notice, this list + * of conditions and the following disclaimer. + * + * * Redistributions in binary form must reproduce the above copyright notice, this + * list of conditions and the following disclaimer in the documentation and/or other + * materials provided with the distribution. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND + * CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, + * INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR + * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, + * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT + * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; + * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) + * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF + * ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + */ #ifdef __SAM3X8E__ -#include "../../inc/MarlinConfigPre.h" +#include "../../../inc/MarlinConfigPre.h" #if HAS_GRAPHICAL_LCD #include -#include "../../Marlin.h" +#include "../../../Marlin.h" void spiBegin(); void spiInit(uint8_t spiRate); void spiSend(uint8_t b); void spiSend(const uint8_t* buf, size_t n); -#include "../shared/Marduino.h" -#include "fastio_Due.h" +#include "../../shared/Marduino.h" +#include "../fastio_Due.h" void u8g_SetPIOutput_DUE_hw_spi(u8g_t *u8g, uint8_t pin_index) { PIO_Configure(g_APinDescription[u8g->pin_list[pin_index]].pPort, PIO_OUTPUT_1, diff --git a/Marlin/src/HAL/HAL_DUE/u8g_com_HAL_DUE_st7920_sw_spi.cpp b/Marlin/src/HAL/HAL_DUE/dogm/u8g_com_HAL_DUE_st7920_sw_spi.cpp similarity index 97% rename from Marlin/src/HAL/HAL_DUE/u8g_com_HAL_DUE_st7920_sw_spi.cpp rename to Marlin/src/HAL/HAL_DUE/dogm/u8g_com_HAL_DUE_st7920_sw_spi.cpp index 8af460954a..47e56fddb0 100644 --- a/Marlin/src/HAL/HAL_DUE/u8g_com_HAL_DUE_st7920_sw_spi.cpp +++ b/Marlin/src/HAL/HAL_DUE/dogm/u8g_com_HAL_DUE_st7920_sw_spi.cpp @@ -55,11 +55,11 @@ #ifdef ARDUINO_ARCH_SAM -#include "../../inc/MarlinConfigPre.h" +#include "../../../inc/MarlinConfigPre.h" #if ENABLED(U8GLIB_ST7920) -#include "../shared/Delay.h" +#include "../../shared/Delay.h" #include @@ -145,8 +145,8 @@ uint8_t u8g_com_HAL_DUE_ST7920_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_va } #if ENABLED(LIGHTWEIGHT_UI) - #include "../../lcd/ultralcd.h" - #include "../shared/HAL_ST7920.h" + #include "../../../lcd/ultralcd.h" + #include "../../shared/HAL_ST7920.h" #define ST7920_CS_PIN LCD_PINS_RS diff --git a/Marlin/src/HAL/HAL_DUE/u8g_com_HAL_DUE_sw_spi.cpp b/Marlin/src/HAL/HAL_DUE/dogm/u8g_com_HAL_DUE_sw_spi.cpp similarity index 97% rename from Marlin/src/HAL/HAL_DUE/u8g_com_HAL_DUE_sw_spi.cpp rename to Marlin/src/HAL/HAL_DUE/dogm/u8g_com_HAL_DUE_sw_spi.cpp index c7929c5c14..e078bc420f 100644 --- a/Marlin/src/HAL/HAL_DUE/u8g_com_HAL_DUE_sw_spi.cpp +++ b/Marlin/src/HAL/HAL_DUE/dogm/u8g_com_HAL_DUE_sw_spi.cpp @@ -55,7 +55,7 @@ #ifdef ARDUINO_ARCH_SAM -#include "../../inc/MarlinConfigPre.h" +#include "../../../inc/MarlinConfigPre.h" #if HAS_GRAPHICAL_LCD && DISABLED(U8GLIB_ST7920) @@ -64,8 +64,8 @@ #include "u8g_com_HAL_DUE_sw_spi_shared.h" -#include "../shared/Marduino.h" -#include "../shared/Delay.h" +#include "../../shared/Marduino.h" +#include "../../shared/Delay.h" #include diff --git a/Marlin/src/HAL/HAL_DUE/u8g_com_HAL_DUE_sw_spi_shared.cpp b/Marlin/src/HAL/HAL_DUE/dogm/u8g_com_HAL_DUE_sw_spi_shared.cpp similarity index 98% rename from Marlin/src/HAL/HAL_DUE/u8g_com_HAL_DUE_sw_spi_shared.cpp rename to Marlin/src/HAL/HAL_DUE/dogm/u8g_com_HAL_DUE_sw_spi_shared.cpp index 673ef4fac2..d3609f60ef 100644 --- a/Marlin/src/HAL/HAL_DUE/u8g_com_HAL_DUE_sw_spi_shared.cpp +++ b/Marlin/src/HAL/HAL_DUE/dogm/u8g_com_HAL_DUE_sw_spi_shared.cpp @@ -55,11 +55,11 @@ #ifdef ARDUINO_ARCH_SAM -#include "../../inc/MarlinConfigPre.h" +#include "../../../inc/MarlinConfigPre.h" #if HAS_GRAPHICAL_LCD -#include "../shared/Delay.h" +#include "../../shared/Delay.h" #include diff --git a/Marlin/src/HAL/HAL_DUE/u8g_com_HAL_DUE_sw_spi_shared.h b/Marlin/src/HAL/HAL_DUE/dogm/u8g_com_HAL_DUE_sw_spi_shared.h similarity index 93% rename from Marlin/src/HAL/HAL_DUE/u8g_com_HAL_DUE_sw_spi_shared.h rename to Marlin/src/HAL/HAL_DUE/dogm/u8g_com_HAL_DUE_sw_spi_shared.h index a7e2432d98..f1cdbba293 100644 --- a/Marlin/src/HAL/HAL_DUE/u8g_com_HAL_DUE_sw_spi_shared.h +++ b/Marlin/src/HAL/HAL_DUE/dogm/u8g_com_HAL_DUE_sw_spi_shared.h @@ -21,8 +21,8 @@ */ #pragma once -#include "../../inc/MarlinConfigPre.h" -#include "../shared/Marduino.h" +#include "../../../inc/MarlinConfigPre.h" +#include "../../shared/Marduino.h" void u8g_SetPIOutput_DUE(u8g_t *u8g, uint8_t pin_index); void u8g_SetPILevel_DUE(u8g_t *u8g, uint8_t pin_index, uint8_t level); diff --git a/Marlin/src/HAL/HAL_DUE/G2_PWM.cpp b/Marlin/src/HAL/HAL_DUE/fastio/G2_PWM.cpp similarity index 99% rename from Marlin/src/HAL/HAL_DUE/G2_PWM.cpp rename to Marlin/src/HAL/HAL_DUE/fastio/G2_PWM.cpp index 1e08332a4e..4afd83ad4b 100644 --- a/Marlin/src/HAL/HAL_DUE/G2_PWM.cpp +++ b/Marlin/src/HAL/HAL_DUE/fastio/G2_PWM.cpp @@ -40,7 +40,7 @@ * Some jitter in the Vref signal is OK so the interrupt priority is left at its default value. */ -#include "../../inc/MarlinConfig.h" +#include "../../../inc/MarlinConfig.h" #if MB(PRINTRBOARD_G2) diff --git a/Marlin/src/HAL/HAL_DUE/G2_PWM.h b/Marlin/src/HAL/HAL_DUE/fastio/G2_PWM.h similarity index 97% rename from Marlin/src/HAL/HAL_DUE/G2_PWM.h rename to Marlin/src/HAL/HAL_DUE/fastio/G2_PWM.h index 8086648bcf..4a84dfe64a 100644 --- a/Marlin/src/HAL/HAL_DUE/G2_PWM.h +++ b/Marlin/src/HAL/HAL_DUE/fastio/G2_PWM.h @@ -26,8 +26,8 @@ * PR #7500. It is hardwired for the PRINTRBOARD_G2 Motor Current needs. */ -#include "../../inc/MarlinConfigPre.h" -#include "../../module/stepper.h" +#include "../../../inc/MarlinConfigPre.h" +#include "../../../module/stepper.h" //C:\Users\bobku\Documents\GitHub\Marlin-Bob-2\Marlin\src\module\stepper.h //C:\Users\bobku\Documents\GitHub\Marlin-Bob-2\Marlin\src\HAL\HAL_DUE\G2_PWM.h diff --git a/Marlin/src/HAL/HAL_DUE/G2_pins.h b/Marlin/src/HAL/HAL_DUE/fastio/G2_pins.h similarity index 100% rename from Marlin/src/HAL/HAL_DUE/G2_pins.h rename to Marlin/src/HAL/HAL_DUE/fastio/G2_pins.h diff --git a/Marlin/src/HAL/HAL_DUE/fastio_Due.h b/Marlin/src/HAL/HAL_DUE/fastio_Due.h index e44d1d1ee6..2bcd604ae5 100644 --- a/Marlin/src/HAL/HAL_DUE/fastio_Due.h +++ b/Marlin/src/HAL/HAL_DUE/fastio_Due.h @@ -39,6 +39,8 @@ #include +#include "../../inc/MarlinConfigPre.h" + /** * Utility functions */ @@ -75,7 +77,7 @@ #if MB(PRINTRBOARD_G2) - #include "G2_pins.h" + #include "fastio/G2_pins.h" // Set pin as input #define _SET_INPUT(IO) do{ \ diff --git a/Marlin/src/HAL/HAL_DUE/inc/Conditionals_LCD.h b/Marlin/src/HAL/HAL_DUE/inc/Conditionals_LCD.h new file mode 100644 index 0000000000..85f26f4016 --- /dev/null +++ b/Marlin/src/HAL/HAL_DUE/inc/Conditionals_LCD.h @@ -0,0 +1,22 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once diff --git a/Marlin/src/HAL/HAL_DUE/inc/Conditionals_adv.h b/Marlin/src/HAL/HAL_DUE/inc/Conditionals_adv.h new file mode 100644 index 0000000000..85f26f4016 --- /dev/null +++ b/Marlin/src/HAL/HAL_DUE/inc/Conditionals_adv.h @@ -0,0 +1,22 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once diff --git a/Marlin/src/HAL/HAL_DUE/inc/Conditionals_post.h b/Marlin/src/HAL/HAL_DUE/inc/Conditionals_post.h new file mode 100644 index 0000000000..85f26f4016 --- /dev/null +++ b/Marlin/src/HAL/HAL_DUE/inc/Conditionals_post.h @@ -0,0 +1,22 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once diff --git a/Marlin/src/HAL/HAL_DUE/SanityCheck.h b/Marlin/src/HAL/HAL_DUE/inc/SanityCheck.h similarity index 100% rename from Marlin/src/HAL/HAL_DUE/SanityCheck.h rename to Marlin/src/HAL/HAL_DUE/inc/SanityCheck.h diff --git a/Marlin/src/HAL/HAL_DUE/persistent_store_eeprom.cpp b/Marlin/src/HAL/HAL_DUE/persistent_store_eeprom.cpp index 6885e98109..b465fcfa75 100644 --- a/Marlin/src/HAL/HAL_DUE/persistent_store_eeprom.cpp +++ b/Marlin/src/HAL/HAL_DUE/persistent_store_eeprom.cpp @@ -29,7 +29,7 @@ #include "../../inc/MarlinConfig.h" #include "../shared/persistent_store_api.h" -#if DISABLED(I2C_EEPROM, SPI_EEPROM) +#if !defined(E2END) && NONE(I2C_EEPROM, SPI_EEPROM) #define E2END 0xFFF // Default to Flash emulated EEPROM size (EepromEmulation_Due.cpp) #endif @@ -38,7 +38,7 @@ extern void eeprom_flush(void); bool PersistentStore::access_start() { return true; } bool PersistentStore::access_finish() { - #if DISABLED(I2C_EEPROM, SPI_EEPROM) + #if NONE(I2C_EEPROM, SPI_EEPROM) eeprom_flush(); #endif return true; diff --git a/Marlin/src/HAL/HAL_DUE/pinsDebug.h b/Marlin/src/HAL/HAL_DUE/pinsDebug.h index 23677960f0..ed78f8adbb 100644 --- a/Marlin/src/HAL/HAL_DUE/pinsDebug.h +++ b/Marlin/src/HAL/HAL_DUE/pinsDebug.h @@ -62,9 +62,8 @@ #define digitalRead_mod(p) extDigitalRead(p) // AVR digitalRead disabled PWM before it read the pin #define PRINT_PORT(p) -#define NAME_FORMAT(p) PSTR("%-##p##s") -#define PRINT_ARRAY_NAME(x) do {sprintf_P(buffer, PSTR("%-" STRINGIFY(MAX_NAME_LENGTH) "s"), pin_array[x].name); SERIAL_ECHO(buffer);} while (0) -#define PRINT_PIN(p) do {sprintf_P(buffer, PSTR("%02d"), p); SERIAL_ECHO(buffer);} while (0) +#define PRINT_ARRAY_NAME(x) do{ sprintf_P(buffer, PSTR("%-" STRINGIFY(MAX_NAME_LENGTH) "s"), pin_array[x].name); SERIAL_ECHO(buffer); }while(0) +#define PRINT_PIN(p) do{ sprintf_P(buffer, PSTR("%02d"), p); SERIAL_ECHO(buffer); }while(0) #define GET_ARRAY_PIN(p) pin_array[p].pin #define GET_ARRAY_IS_DIGITAL(p) pin_array[p].is_digital #define VALID_PIN(pin) (pin >= 0 && pin < (int8_t)NUMBER_PINS_TOTAL ? 1 : 0) diff --git a/Marlin/src/HAL/HAL_DUE/usb/udi_cdc.c b/Marlin/src/HAL/HAL_DUE/usb/udi_cdc.c index e54ee570fa..60c9546ce2 100644 --- a/Marlin/src/HAL/HAL_DUE/usb/udi_cdc.c +++ b/Marlin/src/HAL/HAL_DUE/usb/udi_cdc.c @@ -458,7 +458,7 @@ void udi_cdc_data_sof_notify(void) } -//------------------------------------------------- +// ------------------------ //------- Internal routines to control serial line static uint8_t udi_cdc_setup_to_port(void) @@ -579,7 +579,7 @@ static void udi_cdc_serial_state_msg_sent(udd_ep_status_t status, iram_size_t n, } -//------------------------------------------------- +// ------------------------ //------- Internal routines to process data transfer @@ -781,7 +781,7 @@ static void udi_cdc_tx_send(uint8_t port) } -//--------------------------------------------- +// ------------------------ //------- Application interface diff --git a/Marlin/src/HAL/HAL_DUE/usb/udi_msc.c b/Marlin/src/HAL/HAL_DUE/usb/udi_msc.c index 97d3f2990b..627bca0d4f 100644 --- a/Marlin/src/HAL/HAL_DUE/usb/udi_msc.c +++ b/Marlin/src/HAL/HAL_DUE/usb/udi_msc.c @@ -457,7 +457,7 @@ uint8_t udi_msc_getsetting(void) } -//--------------------------------------------- +// ------------------------ //------- Routines to process CBW packet static void udi_msc_cbw_invalid(void) @@ -613,7 +613,7 @@ static bool udi_msc_cbw_validate(uint32_t alloc_len, uint8_t dir_flag) } -//--------------------------------------------- +// ------------------------ //------- Routines to process small data packet static void udi_msc_data_send(uint8_t * buffer, uint8_t buf_size) @@ -645,7 +645,7 @@ static void udi_msc_data_sent(udd_ep_status_t status, iram_size_t nb_sent, } -//--------------------------------------------- +// ------------------------ //------- Routines to process CSW packet static void udi_msc_csw_process(void) @@ -691,7 +691,7 @@ static void udi_msc_csw_sent(udd_ep_status_t status, iram_size_t nb_sent, } -//--------------------------------------------- +// ------------------------ //------- Routines manage sense data static void udi_msc_clear_sense(void) @@ -757,7 +757,7 @@ static void udi_msc_sense_command_invalid(void) } -//--------------------------------------------- +// ------------------------ //------- Routines manage SCSI Commands static void udi_msc_spc_requestsense(void) diff --git a/Marlin/src/HAL/HAL_DUE/usb/uotghs_device_due.c b/Marlin/src/HAL/HAL_DUE/usb/uotghs_device_due.c index 0dfcd5ac1f..9bac29276c 100644 --- a/Marlin/src/HAL/HAL_DUE/usb/uotghs_device_due.c +++ b/Marlin/src/HAL/HAL_DUE/usb/uotghs_device_due.c @@ -40,6 +40,7 @@ * \asf_license_stop * */ + /* * Support and FAQ: visit Atmel Support */ @@ -505,7 +506,7 @@ static bool udd_ep_interrupt(void); //@} -//-------------------------------------------------------- +// ------------------------ //--- INTERNAL ROUTINES TO MANAGED GLOBAL EVENTS /** @@ -1306,7 +1307,7 @@ void udd_test_mode_packet(void) -//-------------------------------------------------------- +// ------------------------ //--- INTERNAL ROUTINES TO MANAGED THE CONTROL ENDPOINT static void udd_reset_ep_ctrl(void) @@ -1728,7 +1729,7 @@ static bool udd_ctrl_interrupt(void) } -//-------------------------------------------------------- +// ------------------------ //--- INTERNAL ROUTINES TO MANAGED THE BULK/INTERRUPT/ISOCHRONOUS ENDPOINTS #if (0 != USB_DEVICE_MAX_EP) @@ -1904,7 +1905,7 @@ static void udd_ep_in_sent(udd_ep_id_t ep) ptr_src = &ptr_job->buf[ptr_job->buf_cnt]; nb_remain = ptr_job->buf_size - ptr_job->buf_cnt; // Fill a bank even if no data (ZLP) - nb_data = MIN(nb_remain, pkt_size); + nb_data = min(nb_remain, pkt_size); // Modify job information ptr_job->buf_cnt += nb_data; ptr_job->buf_load = nb_data; diff --git a/Marlin/src/HAL/HAL_DUE/usb/uotghs_device_due.h b/Marlin/src/HAL/HAL_DUE/usb/uotghs_device_due.h index 1cd6914f85..97877994bf 100644 --- a/Marlin/src/HAL/HAL_DUE/usb/uotghs_device_due.h +++ b/Marlin/src/HAL/HAL_DUE/usb/uotghs_device_due.h @@ -291,7 +291,7 @@ extern "C" { //! available greater size, then applies register format of UOTGHS controller //! for endpoint size bit-field. #undef udd_format_endpoint_size -#define udd_format_endpoint_size(size) (32 - clz(((uint32_t)MIN(MAX(size, 8), 1024) << 1) - 1) - 1 - 3) +#define udd_format_endpoint_size(size) (32 - clz(((uint32_t)min(max(size, 8), 1024) << 1) - 1) - 1 - 3) //! Configures the selected endpoint size #define udd_configure_endpoint_size(ep, size) (Wr_bitfield(UOTGHS_ARRAY(UOTGHS_DEVEPTCFG[0], ep), UOTGHS_DEVEPTCFG_EPSIZE_Msk, udd_format_endpoint_size(size))) //! Gets the configured selected endpoint size diff --git a/Marlin/src/HAL/HAL_ESP32/HAL.cpp b/Marlin/src/HAL/HAL_ESP32/HAL.cpp index 299aee46fe..535e3b3269 100644 --- a/Marlin/src/HAL/HAL_ESP32/HAL.cpp +++ b/Marlin/src/HAL/HAL_ESP32/HAL.cpp @@ -22,11 +22,8 @@ #ifdef ARDUINO_ARCH_ESP32 -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - #include "HAL.h" +#include "HAL_timers_ESP32.h" #include #include #include @@ -48,49 +45,38 @@ #endif #endif -// -------------------------------------------------------------------------- -// Externals -// -------------------------------------------------------------------------- +// ------------------------ +// Externs +// ------------------------ portMUX_TYPE spinlock = portMUX_INITIALIZER_UNLOCKED; -// -------------------------------------------------------------------------- +// ------------------------ // Local defines -// -------------------------------------------------------------------------- +// ------------------------ #define V_REF 1100 -// -------------------------------------------------------------------------- -// Types -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Variables -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- +// ------------------------ // Public Variables -// -------------------------------------------------------------------------- +// ------------------------ uint16_t HAL_adc_result; -// -------------------------------------------------------------------------- +// ------------------------ // Private Variables -// -------------------------------------------------------------------------- +// ------------------------ -esp_adc_cal_characteristics_t characteristics; +esp_adc_cal_characteristics_t characteristics[ADC_ATTEN_MAX]; +adc_atten_t attenuations[ADC1_CHANNEL_MAX] = {}; +uint32_t thresholds[ADC_ATTEN_MAX]; +volatile int numPWMUsed = 0, + pwmPins[MAX_PWM_PINS], + pwmValues[MAX_PWM_PINS]; -// -------------------------------------------------------------------------- -// Function prototypes -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Private functions -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- +// ------------------------ // Public functions -// -------------------------------------------------------------------------- +// ------------------------ void HAL_init(void) { i2s_init(); @@ -128,9 +114,9 @@ void _delay_ms(int delay_ms) { delay(delay_ms); } // return free memory between end of heap (or end bss) and whatever is current int freeMemory() { return ESP.getFreeHeap(); } -// -------------------------------------------------------------------------- +// ------------------------ // ADC -// -------------------------------------------------------------------------- +// ------------------------ #define ADC1_CHANNEL(pin) ADC1_GPIO ## pin ## _CHANNEL adc1_channel_t get_channel(int pin) { @@ -145,68 +131,132 @@ adc1_channel_t get_channel(int pin) { return ADC1_CHANNEL_MAX; } +void adc1_set_attenuation(adc1_channel_t chan, adc_atten_t atten) { + if (attenuations[chan] != atten) { + adc1_config_channel_atten(chan, atten); + attenuations[chan] = atten; + } +} + void HAL_adc_init() { // Configure ADC adc1_config_width(ADC_WIDTH_12Bit); // Configure channels only if used as (re-)configuring a pin for ADC that is used elsewhere might have adverse effects #if HAS_TEMP_ADC_0 - adc1_config_channel_atten(get_channel(TEMP_0_PIN), ADC_ATTEN_11db); + adc1_set_attenuation(get_channel(TEMP_0_PIN), ADC_ATTEN_11db); #endif #if HAS_TEMP_ADC_1 - adc1_config_channel_atten(get_channel(TEMP_1_PIN), ADC_ATTEN_11db); + adc1_set_attenuation(get_channel(TEMP_1_PIN), ADC_ATTEN_11db); #endif #if HAS_TEMP_ADC_2 - adc1_config_channel_atten(get_channel(TEMP_2_PIN), ADC_ATTEN_11db); + adc1_set_attenuation(get_channel(TEMP_2_PIN), ADC_ATTEN_11db); #endif #if HAS_TEMP_ADC_3 - adc1_config_channel_atten(get_channel(TEMP_3_PIN), ADC_ATTEN_11db); + adc1_set_attenuation(get_channel(TEMP_3_PIN), ADC_ATTEN_11db); #endif #if HAS_TEMP_ADC_4 - adc1_config_channel_atten(get_channel(TEMP_4_PIN), ADC_ATTEN_11db); + adc1_set_attenuation(get_channel(TEMP_4_PIN), ADC_ATTEN_11db); #endif #if HAS_TEMP_ADC_5 - adc1_config_channel_atten(get_channel(TEMP_5_PIN), ADC_ATTEN_11db); + adc1_set_attenuation(get_channel(TEMP_5_PIN), ADC_ATTEN_11db); #endif #if HAS_HEATED_BED - adc1_config_channel_atten(get_channel(TEMP_BED_PIN), ADC_ATTEN_11db); + adc1_set_attenuation(get_channel(TEMP_BED_PIN), ADC_ATTEN_11db); #endif #if HAS_TEMP_CHAMBER - adc1_config_channel_atten(get_channel(TEMP_CHAMBER_PIN), ADC_ATTEN_11db); + adc1_set_attenuation(get_channel(TEMP_CHAMBER_PIN), ADC_ATTEN_11db); #endif #if ENABLED(FILAMENT_WIDTH_SENSOR) - adc1_config_channel_atten(get_channel(FILWIDTH_PIN), ADC_ATTEN_11db); + adc1_set_attenuation(get_channel(FILWIDTH_PIN), ADC_ATTEN_11db); #endif // Note that adc2 is shared with the WiFi module, which has higher priority, so the conversion may fail. // That's why we're not setting it up here. - // Calculate ADC characteristics i.e. gain and offset factors - esp_adc_cal_characterize(ADC_UNIT_1, ADC_ATTEN_DB_11, ADC_WIDTH_BIT_12, V_REF, &characteristics); + // Calculate ADC characteristics (i.e., gain and offset factors for each attenuation level) + for (int i = 0; i < ADC_ATTEN_MAX; i++) { + esp_adc_cal_characterize(ADC_UNIT_1, (adc_atten_t)i, ADC_WIDTH_BIT_12, V_REF, &characteristics[i]); + + // Change attenuation 100mV below the calibrated threshold + thresholds[i] = esp_adc_cal_raw_to_voltage(4095, &characteristics[i]); + } } void HAL_adc_start_conversion(uint8_t adc_pin) { + const adc1_channel_t chan = get_channel(adc_pin); uint32_t mv; - esp_adc_cal_get_voltage((adc_channel_t)get_channel(adc_pin), &characteristics, &mv); + esp_adc_cal_get_voltage((adc_channel_t)chan, &characteristics[attenuations[chan]], &mv); - HAL_adc_result = mv*1023.0/3300.0; + // Change the attenuation level based on the new reading + adc_atten_t atten; + if (mv < thresholds[ADC_ATTEN_DB_0] - 100) + adc1_set_attenuation(chan, ADC_ATTEN_DB_0); + else if (mv > thresholds[ADC_ATTEN_DB_0] - 50 && mv < thresholds[ADC_ATTEN_DB_2_5] - 100) + adc1_set_attenuation(chan, ADC_ATTEN_DB_2_5); + else if (mv > thresholds[ADC_ATTEN_DB_2_5] - 50 && mv < thresholds[ADC_ATTEN_DB_6] - 100) + adc1_set_attenuation(chan, ADC_ATTEN_DB_6); + else if (mv > thresholds[ADC_ATTEN_DB_6] - 50) + adc1_set_attenuation(chan, ADC_ATTEN_DB_11); + + HAL_adc_result = mv * 1023.0 / 3300.0; } void analogWrite(pin_t pin, int value) { - - if (!PWM_PIN(pin)) return; - - static int cnt_channel = 1, - pin_to_channel[40] = {}; - if (pin_to_channel[pin] == 0) { - ledcAttachPin(pin, cnt_channel); - ledcSetup(cnt_channel, 490, 8); - ledcWrite(cnt_channel, value); - - pin_to_channel[pin] = cnt_channel++; + // Use ledc hardware for internal pins + if (pin < 34) { + static int cnt_channel = 1, pin_to_channel[40] = { 0 }; + if (pin_to_channel[pin] == 0) { + ledcAttachPin(pin, cnt_channel); + ledcSetup(cnt_channel, 490, 8); + ledcWrite(cnt_channel, value); + pin_to_channel[pin] = cnt_channel++; + } + ledcWrite(pin_to_channel[pin], value); + return; } - ledcWrite(pin_to_channel[pin], value); + int idx = -1; + + // Search Pin + for (int i = 0; i < numPWMUsed; ++i) + if (pwmPins[i] == pin) { idx = i; break; } + + // not found ? + if (idx < 0) { + // No slots remaining + if (numPWMUsed >= MAX_PWM_PINS) return; + + // Take new slot for pin + idx = numPWMUsed; + pwmPins[idx] = pin; + // Start timer on first use + if (idx == 0) HAL_timer_start(PWM_TIMER_NUM, PWM_TIMER_FREQUENCY); + + ++numPWMUsed; + } + + // Use 7bit internal value - add 1 to have 100% high at 255 + pwmValues[idx] = (value + 1) / 2; +} + +// Handle PWM timer interrupt +HAL_PWM_TIMER_ISR() { + HAL_timer_isr_prologue(PWM_TIMER_NUM); + + static uint8_t count = 0; + + for (int i = 0; i < numPWMUsed; ++i) { + if (count == 0) // Start of interval + WRITE(pwmPins[i], pwmValues[i] ? HIGH : LOW); + else if (pwmValues[i] == count) // End of duration + WRITE(pwmPins[i], LOW); + } + + // 128 for 7 Bit resolution + count = (count + 1) & 0x7F; + + HAL_timer_isr_epilogue(PWM_TIMER_NUM); } #endif // ARDUINO_ARCH_ESP32 diff --git a/Marlin/src/HAL/HAL_ESP32/HAL.h b/Marlin/src/HAL/HAL_ESP32/HAL.h index 0fc1d71bc4..5327a8789e 100644 --- a/Marlin/src/HAL/HAL_ESP32/HAL.h +++ b/Marlin/src/HAL/HAL_ESP32/HAL.h @@ -24,10 +24,6 @@ #define CPU_32_BIT -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - #include #include "../shared/Marduino.h" @@ -43,9 +39,9 @@ #include "WebSocketSerial.h" #include "FlushableHardwareSerial.h" -// -------------------------------------------------------------------------- +// ------------------------ // Defines -// -------------------------------------------------------------------------- +// ------------------------ extern portMUX_TYPE spinlock; @@ -69,24 +65,24 @@ extern portMUX_TYPE spinlock; #undef pgm_read_ptr #define pgm_read_ptr(addr) (*(addr)) -// -------------------------------------------------------------------------- +// ------------------------ // Types -// -------------------------------------------------------------------------- +// ------------------------ typedef int16_t pin_t; #define HAL_SERVO_LIB Servo -// -------------------------------------------------------------------------- +// ------------------------ // Public Variables -// -------------------------------------------------------------------------- +// ------------------------ /** result of last ADC conversion */ extern uint16_t HAL_adc_result; -// -------------------------------------------------------------------------- +// ------------------------ // Public functions -// -------------------------------------------------------------------------- +// ------------------------ // clear reset reason void HAL_clear_reset_source (void); diff --git a/Marlin/src/HAL/HAL_ESP32/HAL_Servo_ESP32.cpp b/Marlin/src/HAL/HAL_ESP32/HAL_Servo_ESP32.cpp index e702539ca9..5f2dd40e19 100644 --- a/Marlin/src/HAL/HAL_ESP32/HAL_Servo_ESP32.cpp +++ b/Marlin/src/HAL/HAL_ESP32/HAL_Servo_ESP32.cpp @@ -48,8 +48,8 @@ void Servo::detach() { ledcDetachPin(this->pin); } int Servo::read() { return this->degrees; } -void Servo::write(int degrees) { - this->degrees = constrain(degrees, MIN_ANGLE, MAX_ANGLE); +void Servo::write(int inDegrees) { + this->degrees = constrain(inDegrees, MIN_ANGLE, MAX_ANGLE); int us = map(this->degrees, MIN_ANGLE, MAX_ANGLE, MIN_PULSE_WIDTH, MAX_PULSE_WIDTH); int duty = map(us, 0, TAU_USEC, 0, MAX_COMPARE); ledcWrite(channel, duty); diff --git a/Marlin/src/HAL/HAL_ESP32/HAL_spi_ESP32.cpp b/Marlin/src/HAL/HAL_ESP32/HAL_spi_ESP32.cpp index 67d7e25972..85c0879712 100644 --- a/Marlin/src/HAL/HAL_ESP32/HAL_spi_ESP32.cpp +++ b/Marlin/src/HAL/HAL_ESP32/HAL_spi_ESP32.cpp @@ -23,10 +23,6 @@ #ifdef ARDUINO_ARCH_ESP32 -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - #include "HAL.h" #include "../shared/HAL_SPI.h" #include @@ -34,28 +30,28 @@ #include "../../core/macros.h" #include -// -------------------------------------------------------------------------- +// ------------------------ // Public Variables -// -------------------------------------------------------------------------- +// ------------------------ static SPISettings spiConfig; -// -------------------------------------------------------------------------- +// ------------------------ // Public functions -// -------------------------------------------------------------------------- +// ------------------------ #if ENABLED(SOFTWARE_SPI) - // -------------------------------------------------------------------------- + // ------------------------ // Software SPI - // -------------------------------------------------------------------------- + // ------------------------ #error "Software SPI not supported for ESP32. Use Hardware SPI." #else -// -------------------------------------------------------------------------- +// ------------------------ // Hardware SPI -// -------------------------------------------------------------------------- +// ------------------------ void spiBegin() { #if !PIN_EXISTS(SS) diff --git a/Marlin/src/HAL/HAL_ESP32/HAL_timers_ESP32.cpp b/Marlin/src/HAL/HAL_ESP32/HAL_timers_ESP32.cpp index fb95e36e27..fc90af4b8f 100644 --- a/Marlin/src/HAL/HAL_ESP32/HAL_timers_ESP32.cpp +++ b/Marlin/src/HAL/HAL_ESP32/HAL_timers_ESP32.cpp @@ -22,10 +22,6 @@ #ifdef ARDUINO_ARCH_ESP32 -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - #include #include "esp_types.h" #include "soc/timer_group_struct.h" @@ -36,72 +32,51 @@ #include "HAL_timers_ESP32.h" -// -------------------------------------------------------------------------- -// Externals -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- +// ------------------------ // Local defines -// -------------------------------------------------------------------------- +// ------------------------ #define NUM_HARDWARE_TIMERS 4 -// -------------------------------------------------------------------------- -// Types -// -------------------------------------------------------------------------- - - -// -------------------------------------------------------------------------- -// Public Variables -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- +// ------------------------ // Private Variables -// -------------------------------------------------------------------------- +// ------------------------ static timg_dev_t *TG[2] = {&TIMERG0, &TIMERG1}; const tTimerConfig TimerConfig [NUM_HARDWARE_TIMERS] = { { TIMER_GROUP_0, TIMER_0, STEPPER_TIMER_PRESCALE, stepTC_Handler }, // 0 - Stepper { TIMER_GROUP_0, TIMER_1, TEMP_TIMER_PRESCALE, tempTC_Handler }, // 1 - Temperature - { TIMER_GROUP_1, TIMER_0, 1, nullptr }, // 2 + { TIMER_GROUP_1, TIMER_0, PWM_TIMER_PRESCALE, pwmTC_Handler }, // 2 - PWM { TIMER_GROUP_1, TIMER_1, 1, nullptr }, // 3 }; -// -------------------------------------------------------------------------- -// Function prototypes -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Private functions -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- +// ------------------------ // Public functions -// -------------------------------------------------------------------------- +// ------------------------ -void IRAM_ATTR timer_group0_isr(void *para) { - const int timer_idx = (int)para; +void IRAM_ATTR timer_isr(void *para) { + const tTimerConfig& timer = TimerConfig[(int)para]; // Retrieve the interrupt status and the counter value // from the timer that reported the interrupt - uint32_t intr_status = TIMERG0.int_st_timers.val; - TIMERG0.hw_timer[timer_idx].update = 1; + uint32_t intr_status = TG[timer.group]->int_st_timers.val; + TG[timer.group]->hw_timer[timer.idx].update = 1; // Clear the interrupt - if (intr_status & BIT(timer_idx)) { - switch (timer_idx) { - case TIMER_0: TIMERG0.int_clr_timers.t0 = 1; break; - case TIMER_1: TIMERG0.int_clr_timers.t1 = 1; break; + if (intr_status & BIT(timer.idx)) { + switch (timer.idx) { + case TIMER_0: TG[timer.group]->int_clr_timers.t0 = 1; break; + case TIMER_1: TG[timer.group]->int_clr_timers.t1 = 1; break; + case TIMER_MAX: break; } } - const tTimerConfig timer = TimerConfig[timer_idx]; timer.fn(); // After the alarm has been triggered // Enable it again so it gets triggered the next time - TIMERG0.hw_timer[timer_idx].config.alarm_en = TIMER_ALARM_EN; + TG[timer.group]->hw_timer[timer.idx].config.alarm_en = TIMER_ALARM_EN; } /** @@ -131,8 +106,7 @@ void HAL_timer_start(const uint8_t timer_num, uint32_t frequency) { timer_enable_intr(timer.group, timer.idx); - // TODO need to deal with timer_group1_isr - timer_isr_register(timer.group, timer.idx, timer_group0_isr, (void*)timer.idx, 0, nullptr); + timer_isr_register(timer.group, timer.idx, timer_isr, (void*)timer_num, 0, nullptr); timer_start(timer.group, timer.idx); } diff --git a/Marlin/src/HAL/HAL_ESP32/HAL_timers_ESP32.h b/Marlin/src/HAL/HAL_ESP32/HAL_timers_ESP32.h index 1a05c04a08..0806fd2c77 100644 --- a/Marlin/src/HAL/HAL_ESP32/HAL_timers_ESP32.h +++ b/Marlin/src/HAL/HAL_ESP32/HAL_timers_ESP32.h @@ -21,10 +21,6 @@ */ #pragma once -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - #include #include "driver/timer.h" @@ -33,9 +29,9 @@ #include "../../inc/MarlinConfig.h" #include "../../pins/pins.h" -// -------------------------------------------------------------------------- +// ------------------------ // Defines -// -------------------------------------------------------------------------- +// ------------------------ // #define FORCE_INLINE __attribute__((always_inline)) inline @@ -44,6 +40,7 @@ typedef uint64_t hal_timer_t; #define STEP_TIMER_NUM 0 // index of timer to use for stepper #define TEMP_TIMER_NUM 1 // index of timer to use for temperature +#define PWM_TIMER_NUM 2 // index of timer to use for PWM outputs #define PULSE_TIMER_NUM STEP_TIMER_NUM #define HAL_TIMER_RATE APB_CLK_FREQ // frequency of timer peripherals @@ -63,6 +60,14 @@ typedef uint64_t hal_timer_t; #define TEMP_TIMER_PRESCALE 1000 // prescaler for setting Temp timer, 72Khz #define TEMP_TIMER_FREQUENCY 1000 // temperature interrupt frequency +#define PWM_TIMER_PRESCALE 10 +#if ENABLED(FAST_PWM_FAN) + #define PWM_TIMER_FREQUENCY FAST_PWM_FAN_FREQUENCY +#else + #define PWM_TIMER_FREQUENCY (50*128) // 50Hz and 7bit resolution +#endif +#define MAX_PWM_PINS 32 // Number of PWM pin-slots + #define PULSE_TIMER_RATE STEPPER_TIMER_RATE // frequency of pulse timer #define PULSE_TIMER_PRESCALE STEPPER_TIMER_PRESCALE #define PULSE_TIMER_TICKS_PER_US STEPPER_TIMER_TICKS_PER_US @@ -76,14 +81,15 @@ typedef uint64_t hal_timer_t; #define HAL_TEMP_TIMER_ISR() extern "C" void tempTC_Handler(void) #define HAL_STEP_TIMER_ISR() extern "C" void stepTC_Handler(void) +#define HAL_PWM_TIMER_ISR() extern "C" void pwmTC_Handler(void) extern "C" void tempTC_Handler(void); extern "C" void stepTC_Handler(void); +extern "C" void pwmTC_Handler(void); - -// -------------------------------------------------------------------------- +// ------------------------ // Types -// -------------------------------------------------------------------------- +// ------------------------ typedef struct { timer_group_t group; @@ -92,15 +98,15 @@ typedef struct { void (*fn)(void); } tTimerConfig; -// -------------------------------------------------------------------------- +// ------------------------ // Public Variables -// -------------------------------------------------------------------------- +// ------------------------ extern const tTimerConfig TimerConfig[]; -// -------------------------------------------------------------------------- +// ------------------------ // Public functions -// -------------------------------------------------------------------------- +// ------------------------ void HAL_timer_start (const uint8_t timer_num, uint32_t frequency); void HAL_timer_set_compare(const uint8_t timer_num, const hal_timer_t count); diff --git a/Marlin/src/HAL/HAL_ESP32/fastio_ESP32.h b/Marlin/src/HAL/HAL_ESP32/fastio_ESP32.h index 3647774095..1641116b90 100644 --- a/Marlin/src/HAL/HAL_ESP32/fastio_ESP32.h +++ b/Marlin/src/HAL/HAL_ESP32/fastio_ESP32.h @@ -66,7 +66,7 @@ #define extDigitalWrite(IO,V) digitalWrite(IO,V) // PWM outputs -#define PWM_PIN(P) (P < 34) // NOTE Pins >= 34 are input only on ESP32, so they can't be used for output. +#define PWM_PIN(P) (P < 34 || P > 127) // NOTE Pins >= 34 are input only on ESP32, so they can't be used for output. // Toggle pin value #define TOGGLE(IO) WRITE(IO, !READ(IO)) diff --git a/Marlin/src/HAL/HAL_ESP32/i2s.cpp b/Marlin/src/HAL/HAL_ESP32/i2s.cpp index 557714f870..1f7c508cf1 100644 --- a/Marlin/src/HAL/HAL_ESP32/i2s.cpp +++ b/Marlin/src/HAL/HAL_ESP32/i2s.cpp @@ -56,7 +56,7 @@ static i2s_dev_t* I2S[I2S_NUM_MAX] = {&I2S0, &I2S1}; static i2s_dma_t dma; // output value -uint32_t i2s_port_data; +uint32_t i2s_port_data = 0; #define I2S_ENTER_CRITICAL() portENTER_CRITICAL(&i2s_spinlock[i2s_num]) #define I2S_EXIT_CRITICAL() portEXIT_CRITICAL(&i2s_spinlock[i2s_num]) @@ -140,13 +140,13 @@ static void IRAM_ATTR i2s_intr_handler_default(void *arg) { } void stepperTask(void* parameter) { - uint32_t i, remaining = 0; + uint32_t remaining = 0; while (1) { xQueueReceive(dma.queue, &dma.current, portMAX_DELAY); dma.rw_pos = 0; - for (i = 0; i < DMA_SAMPLE_COUNT; i++) { + while (dma.rw_pos < DMA_SAMPLE_COUNT) { // Fill with the port data post pulse_phase until the next step if (remaining) { i2s_push_sample(); @@ -254,7 +254,13 @@ int i2s_init() { I2S0.fifo_conf.dscr_en = 0; - I2S0.conf_chan.tx_chan_mod = 0; + I2S0.conf_chan.tx_chan_mod = ( + #if ENABLED(I2S_STEPPER_SPLIT_STREAM) + 4 + #else + 0 + #endif + ); I2S0.fifo_conf.tx_fifo_mod = 0; I2S0.conf.tx_mono = 0; @@ -314,10 +320,19 @@ int i2s_init() { } void i2s_write(uint8_t pin, uint8_t val) { + #if ENABLED(I2S_STEPPER_SPLIT_STREAM) + if (pin >= 16) { + SET_BIT_TO(I2S0.conf_single_data, pin, val); + return; + } + #endif SET_BIT_TO(i2s_port_data, pin, val); } uint8_t i2s_state(uint8_t pin) { + #if ENABLED(I2S_STEPPER_SPLIT_STREAM) + if (pin >= 16) return TEST(I2S0.conf_single_data, pin); + #endif return TEST(i2s_port_data, pin); } diff --git a/Marlin/src/HAL/HAL_ESP32/inc/Conditionals_LCD.h b/Marlin/src/HAL/HAL_ESP32/inc/Conditionals_LCD.h new file mode 100644 index 0000000000..85f26f4016 --- /dev/null +++ b/Marlin/src/HAL/HAL_ESP32/inc/Conditionals_LCD.h @@ -0,0 +1,22 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once diff --git a/Marlin/src/HAL/HAL_ESP32/inc/Conditionals_adv.h b/Marlin/src/HAL/HAL_ESP32/inc/Conditionals_adv.h new file mode 100644 index 0000000000..85f26f4016 --- /dev/null +++ b/Marlin/src/HAL/HAL_ESP32/inc/Conditionals_adv.h @@ -0,0 +1,22 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once diff --git a/Marlin/src/HAL/HAL_ESP32/inc/Conditionals_post.h b/Marlin/src/HAL/HAL_ESP32/inc/Conditionals_post.h new file mode 100644 index 0000000000..85f26f4016 --- /dev/null +++ b/Marlin/src/HAL/HAL_ESP32/inc/Conditionals_post.h @@ -0,0 +1,22 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once diff --git a/Marlin/src/HAL/HAL_ESP32/SanityCheck.h b/Marlin/src/HAL/HAL_ESP32/inc/SanityCheck.h similarity index 100% rename from Marlin/src/HAL/HAL_ESP32/SanityCheck.h rename to Marlin/src/HAL/HAL_ESP32/inc/SanityCheck.h diff --git a/Marlin/src/HAL/HAL_LINUX/HAL.cpp b/Marlin/src/HAL/HAL_LINUX/HAL.cpp index 854d7247f6..0251e2e4e6 100644 --- a/Marlin/src/HAL/HAL_LINUX/HAL.cpp +++ b/Marlin/src/HAL/HAL_LINUX/HAL.cpp @@ -47,9 +47,9 @@ int freeMemory() { return 0; } -// -------------------------------------------------------------------------- +// ------------------------ // ADC -// -------------------------------------------------------------------------- +// ------------------------ void HAL_adc_init(void) { diff --git a/Marlin/src/HAL/HAL_LINUX/HAL.h b/Marlin/src/HAL/HAL_LINUX/HAL.h index a87e400394..fbbce96dbd 100644 --- a/Marlin/src/HAL/HAL_LINUX/HAL.h +++ b/Marlin/src/HAL/HAL_LINUX/HAL.h @@ -23,10 +23,6 @@ #define CPU_32_BIT -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - #define F_CPU 100000000 #define SystemCoreClock F_CPU #include diff --git a/Marlin/src/HAL/HAL_LINUX/HAL_timers.h b/Marlin/src/HAL/HAL_LINUX/HAL_timers.h index b7d0f9b2da..e883cb0150 100644 --- a/Marlin/src/HAL/HAL_LINUX/HAL_timers.h +++ b/Marlin/src/HAL/HAL_LINUX/HAL_timers.h @@ -24,15 +24,11 @@ * HAL timers for Linux X86_64 */ -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - #include -// -------------------------------------------------------------------------- +// ------------------------ // Defines -// -------------------------------------------------------------------------- +// ------------------------ #define FORCE_INLINE __attribute__((always_inline)) inline diff --git a/Marlin/src/HAL/HAL_LINUX/inc/Conditionals_LCD.h b/Marlin/src/HAL/HAL_LINUX/inc/Conditionals_LCD.h new file mode 100644 index 0000000000..85f26f4016 --- /dev/null +++ b/Marlin/src/HAL/HAL_LINUX/inc/Conditionals_LCD.h @@ -0,0 +1,22 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once diff --git a/Marlin/src/HAL/HAL_LINUX/inc/Conditionals_adv.h b/Marlin/src/HAL/HAL_LINUX/inc/Conditionals_adv.h new file mode 100644 index 0000000000..85f26f4016 --- /dev/null +++ b/Marlin/src/HAL/HAL_LINUX/inc/Conditionals_adv.h @@ -0,0 +1,22 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once diff --git a/Marlin/src/HAL/HAL_LINUX/inc/Conditionals_post.h b/Marlin/src/HAL/HAL_LINUX/inc/Conditionals_post.h new file mode 100644 index 0000000000..85f26f4016 --- /dev/null +++ b/Marlin/src/HAL/HAL_LINUX/inc/Conditionals_post.h @@ -0,0 +1,22 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once diff --git a/Marlin/src/HAL/HAL_LINUX/SanityCheck.h b/Marlin/src/HAL/HAL_LINUX/inc/SanityCheck.h similarity index 100% rename from Marlin/src/HAL/HAL_LINUX/SanityCheck.h rename to Marlin/src/HAL/HAL_LINUX/inc/SanityCheck.h diff --git a/Marlin/src/HAL/HAL_LINUX/include/Arduino.h b/Marlin/src/HAL/HAL_LINUX/include/Arduino.h index f73a9c9161..0d29df466e 100644 --- a/Marlin/src/HAL/HAL_LINUX/include/Arduino.h +++ b/Marlin/src/HAL/HAL_LINUX/include/Arduino.h @@ -43,8 +43,6 @@ #define FALLING 0x03 #define RISING 0x04 -#define E2END 0xFFF // EEPROM end address - typedef uint8_t byte; #define PROGMEM #define PSTR(v) (v) diff --git a/Marlin/src/HAL/HAL_LINUX/include/serial.h b/Marlin/src/HAL/HAL_LINUX/include/serial.h index dd57d99749..e212276404 100644 --- a/Marlin/src/HAL/HAL_LINUX/include/serial.h +++ b/Marlin/src/HAL/HAL_LINUX/include/serial.h @@ -83,8 +83,9 @@ public: HalSerial() { host_connected = true; } - void begin(int32_t baud) { - } + void begin(int32_t baud) { } + + void end() { } int peek() { uint8_t value; diff --git a/Marlin/src/HAL/HAL_LINUX/main.cpp b/Marlin/src/HAL/HAL_LINUX/main.cpp index 8004138c89..01b0eee34d 100644 --- a/Marlin/src/HAL/HAL_LINUX/main.cpp +++ b/Marlin/src/HAL/HAL_LINUX/main.cpp @@ -49,7 +49,7 @@ void write_serial_thread() { void read_serial_thread() { char buffer[255] = {}; for (;;) { - std::size_t len = MIN(usb_serial.receive_buffer.free(), 254U); + std::size_t len = _MIN(usb_serial.receive_buffer.free(), 254U); if (fgets(buffer, len, stdin)) for (std::size_t i = 0; i < strlen(buffer); i++) usb_serial.receive_buffer.write(buffer[i]); diff --git a/Marlin/src/HAL/HAL_LINUX/persistent_store_impl.cpp b/Marlin/src/HAL/HAL_LINUX/persistent_store_impl.cpp index aba664d9f9..c4965d90e3 100644 --- a/Marlin/src/HAL/HAL_LINUX/persistent_store_impl.cpp +++ b/Marlin/src/HAL/HAL_LINUX/persistent_store_impl.cpp @@ -29,7 +29,8 @@ #include "../shared/persistent_store_api.h" #include -uint8_t buffer[E2END]; +#define LINUX_EEPROM_SIZE (E2END + 1) +uint8_t buffer[LINUX_EEPROM_SIZE]; char filename[] = "eeprom.dat"; bool PersistentStore::access_start() { @@ -40,8 +41,8 @@ bool PersistentStore::access_start() { fseek(eeprom_file, 0L, SEEK_END); std::size_t file_size = ftell(eeprom_file); - if (file_size < E2END) { - memset(buffer + file_size, eeprom_erase_value, E2END - file_size); + if (file_size < LINUX_EEPROM_SIZE) { + memset(buffer + file_size, eeprom_erase_value, LINUX_EEPROM_SIZE - file_size); } else { fseek(eeprom_file, 0L, SEEK_SET); @@ -60,7 +61,7 @@ bool PersistentStore::access_finish() { return true; } -bool PersistentStore::write_data(int &pos, const uint8_t *value, const size_t size, uint16_t *crc) { +bool PersistentStore::write_data(int &pos, const uint8_t *value, size_t size, uint16_t *crc) { std::size_t bytes_written = 0; for (std::size_t i = 0; i < size; i++) { diff --git a/Marlin/src/HAL/HAL_LINUX/pinsDebug.h b/Marlin/src/HAL/HAL_LINUX/pinsDebug.h index be4765a571..a28d2b60b9 100644 --- a/Marlin/src/HAL/HAL_LINUX/pinsDebug.h +++ b/Marlin/src/HAL/HAL_LINUX/pinsDebug.h @@ -32,9 +32,8 @@ #define digitalRead_mod(p) digitalRead(p) #define PRINT_PORT(p) #define GET_ARRAY_PIN(p) pin_array[p].pin -#define NAME_FORMAT(p) PSTR("%-##p##s") -#define PRINT_ARRAY_NAME(x) do {sprintf_P(buffer, PSTR("%-" STRINGIFY(MAX_NAME_LENGTH) "s"), pin_array[x].name); SERIAL_ECHO(buffer);} while (0) -#define PRINT_PIN(p) do {sprintf_P(buffer, PSTR("%3d "), p); SERIAL_ECHO(buffer);} while (0) +#define PRINT_ARRAY_NAME(x) do{ sprintf_P(buffer, PSTR("%-" STRINGIFY(MAX_NAME_LENGTH) "s"), pin_array[x].name); SERIAL_ECHO(buffer); }while(0) +#define PRINT_PIN(p) do{ sprintf_P(buffer, PSTR("%3d "), p); SERIAL_ECHO(buffer); }while(0) #define MULTI_NAME_PAD 16 // space needed to be pretty if not first name assigned to a pin // active ADC function/mode/code values for PINSEL registers diff --git a/Marlin/src/HAL/HAL_LINUX/spi_pins.h b/Marlin/src/HAL/HAL_LINUX/spi_pins.h index 5b6f88ac6d..fdd09b1c03 100644 --- a/Marlin/src/HAL/HAL_LINUX/spi_pins.h +++ b/Marlin/src/HAL/HAL_LINUX/spi_pins.h @@ -24,9 +24,9 @@ #include "../../core/macros.h" #include "../../inc/MarlinConfigPre.h" -#if BOTH(SDSUPPORT, DOGLCD) && (LCD_PINS_D4 == SCK_PIN || LCD_PINS_ENABLE == MOSI_PIN || DOGLCD_SCK == SCK_PIN || DOGLCD_MOSI == MOSI_PIN) +#if HAS_GRAPHICAL_LCD && ENABLED(SDSUPPORT) && (LCD_PINS_D4 == SCK_PIN || LCD_PINS_ENABLE == MOSI_PIN || DOGLCD_SCK == SCK_PIN || DOGLCD_MOSI == MOSI_PIN) #define LPC_SOFTWARE_SPI // If the SD card and LCD adapter share the same SPI pins, then software SPI is currently - // needed due to the speed and mode requred for communicating with each device being different. + // needed due to the speed and mode required for communicating with each device being different. // This requirement can be removed if the SPI access to these devices is updated to use // spiBeginTransaction. #endif diff --git a/Marlin/src/HAL/HAL_LPC1768/HAL.h b/Marlin/src/HAL/HAL_LPC1768/HAL.h index 32765bd0ea..ce3828cd51 100644 --- a/Marlin/src/HAL/HAL_LPC1768/HAL.h +++ b/Marlin/src/HAL/HAL_LPC1768/HAL.h @@ -34,7 +34,7 @@ void HAL_init(void); #include #include -extern "C" volatile millis_t _millis; +extern "C" volatile uint32_t _millis; #include "../shared/Marduino.h" #include "../shared/math_32bit.h" @@ -133,7 +133,7 @@ uint8_t spiRec(uint32_t chan); // Memory usage per ADC channel (bytes): (6 * ADC_MEDIAN_FILTER_SIZE) + 16 // 8 * ((6 * 23) + 16 ) = 1232 Bytes for 8 channels -#define ADC_LOWPASS_K_VALUE (6) // Higher values increase rise time +#define ADC_LOWPASS_K_VALUE (2) // Higher values increase rise time // Rise time sample delays for 100% signal convergence on full range step // (1 : 13, 2 : 32, 3 : 67, 4 : 139, 5 : 281, 6 : 565, 7 : 1135, 8 : 2273) // K = 6, 565 samples, 500Hz sample rate, 1.13s convergence on full range step @@ -147,7 +147,9 @@ using FilteredADC = LPC176x::ADC; #define HAL_ADC_READY() FilteredADC::finished_conversion() // A grace period to allow ADC readings to stabilize, preventing false alarms -#define THERMAL_PROTECTION_GRACE_PERIOD 1000 +#ifndef THERMAL_PROTECTION_GRACE_PERIOD + #define THERMAL_PROTECTION_GRACE_PERIOD 1000 +#endif // Parse a G-code word into a pin index int16_t PARSED_PIN_INDEX(const char code, const int16_t dval); diff --git a/Marlin/src/HAL/HAL_LPC1768/HAL_spi.cpp b/Marlin/src/HAL/HAL_LPC1768/HAL_spi.cpp index 1f12973f71..5652db988b 100644 --- a/Marlin/src/HAL/HAL_LPC1768/HAL_spi.cpp +++ b/Marlin/src/HAL/HAL_LPC1768/HAL_spi.cpp @@ -49,15 +49,11 @@ #ifdef TARGET_LPC1768 #include "../../inc/MarlinConfig.h" -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - #include -// -------------------------------------------------------------------------- +// ------------------------ // Public functions -// -------------------------------------------------------------------------- +// ------------------------ #if ENABLED(LPC_SOFTWARE_SPI) #include "SoftwareSPI.h" @@ -162,7 +158,7 @@ // setup for SPI mode SSP_CFG_Type HW_SPI_init; // data structure to hold init values SSP_ConfigStructInit(&HW_SPI_init); // set values for SPI mode - HW_SPI_init.ClockRate = Marlin_speed[MIN(spiRate, 6)]; // put in the specified bit rate + HW_SPI_init.ClockRate = Marlin_speed[_MIN(spiRate, 6)]; // put in the specified bit rate HW_SPI_init.Mode |= SSP_CR1_SSP_EN; SSP_Init(LPC_SSPn, &HW_SPI_init); // puts the values into the proper bits in the SSP0 registers } diff --git a/Marlin/src/HAL/HAL_LPC1768/HAL_timers.h b/Marlin/src/HAL/HAL_LPC1768/HAL_timers.h index 1d68ee8478..29cb8c437e 100644 --- a/Marlin/src/HAL/HAL_LPC1768/HAL_timers.h +++ b/Marlin/src/HAL/HAL_LPC1768/HAL_timers.h @@ -25,10 +25,6 @@ * HAL For LPC1768 */ -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - #include #include "../../core/macros.h" @@ -51,9 +47,9 @@ #define SBIT_MR3R 10 #define SBIT_MR3S 11 -// -------------------------------------------------------------------------- +// ------------------------ // Defines -// -------------------------------------------------------------------------- +// ------------------------ #define _HAL_TIMER(T) _CAT(LPC_TIM, T) #define _HAL_TIMER_IRQ(T) TIMER##T##_IRQn @@ -95,9 +91,9 @@ typedef uint32_t hal_timer_t; #define STEP_TIMER _HAL_TIMER(STEP_TIMER_NUM) #define TEMP_TIMER _HAL_TIMER(TEMP_TIMER_NUM) -// -------------------------------------------------------------------------- +// ------------------------ // Public functions -// -------------------------------------------------------------------------- +// ------------------------ void HAL_timer_init(void); void HAL_timer_start(const uint8_t timer_num, const uint32_t frequency); diff --git a/Marlin/src/HAL/HAL_LPC1768/MarlinSerial.h b/Marlin/src/HAL/HAL_LPC1768/MarlinSerial.h index 4807356d73..1f282f64a3 100644 --- a/Marlin/src/HAL/HAL_LPC1768/MarlinSerial.h +++ b/Marlin/src/HAL/HAL_LPC1768/MarlinSerial.h @@ -49,6 +49,8 @@ public: { } + void end() { } + #if ENABLED(EMERGENCY_PARSER) bool recv_callback(const char c) override { emergency_parser.update(emergency_state, c); diff --git a/Marlin/src/HAL/HAL_LPC1768/inc/Conditionals_LCD.h b/Marlin/src/HAL/HAL_LPC1768/inc/Conditionals_LCD.h new file mode 100644 index 0000000000..85f26f4016 --- /dev/null +++ b/Marlin/src/HAL/HAL_LPC1768/inc/Conditionals_LCD.h @@ -0,0 +1,22 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once diff --git a/Marlin/src/HAL/HAL_LPC1768/inc/Conditionals_adv.h b/Marlin/src/HAL/HAL_LPC1768/inc/Conditionals_adv.h new file mode 100644 index 0000000000..85f26f4016 --- /dev/null +++ b/Marlin/src/HAL/HAL_LPC1768/inc/Conditionals_adv.h @@ -0,0 +1,22 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once diff --git a/Marlin/src/HAL/HAL_LPC1768/inc/Conditionals_post.h b/Marlin/src/HAL/HAL_LPC1768/inc/Conditionals_post.h new file mode 100644 index 0000000000..85f26f4016 --- /dev/null +++ b/Marlin/src/HAL/HAL_LPC1768/inc/Conditionals_post.h @@ -0,0 +1,22 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once diff --git a/Marlin/src/HAL/HAL_LPC1768/SanityCheck.h b/Marlin/src/HAL/HAL_LPC1768/inc/SanityCheck.h similarity index 100% rename from Marlin/src/HAL/HAL_LPC1768/SanityCheck.h rename to Marlin/src/HAL/HAL_LPC1768/inc/SanityCheck.h diff --git a/Marlin/src/HAL/HAL_LPC1768/main.cpp b/Marlin/src/HAL/HAL_LPC1768/main.cpp index 3f22b0d36d..fa3d27dbb6 100644 --- a/Marlin/src/HAL/HAL_LPC1768/main.cpp +++ b/Marlin/src/HAL/HAL_LPC1768/main.cpp @@ -44,9 +44,7 @@ extern uint32_t MSC_SD_Init(uint8_t pdrv); extern "C" int isLPC1769(); extern "C" void disk_timerproc(void); -void SysTick_Callback() { - disk_timerproc(); -} +void SysTick_Callback() { disk_timerproc(); } void HAL_init(void) { @@ -75,17 +73,18 @@ void HAL_init(void) { #endif // Init Servo Pins - #if PIN_EXISTS(SERVO0) - OUT_WRITE(SERVO0_PIN, LOW); + #define INIT_SERVO(N) OUT_WRITE(SERVO##N##_PIN, LOW) + #if HAS_SERVO_0 + INIT_SERVO(0); #endif - #if PIN_EXISTS(SERVO1) - OUT_WRITE(SERVO1_PIN, LOW); + #if HAS_SERVO_1 + INIT_SERVO(1); #endif - #if PIN_EXISTS(SERVO2) - OUT_WRITE(SERVO2_PIN, LOW); + #if HAS_SERVO_2 + INIT_SERVO(2); #endif - #if PIN_EXISTS(SERVO3) - OUT_WRITE(SERVO3_PIN, LOW); + #if HAS_SERVO_3 + INIT_SERVO(3); #endif //debug_frmwrk_init(); @@ -99,6 +98,26 @@ void HAL_init(void) { OUT_WRITE(ONBOARD_SD_CS_PIN, HIGH); #endif + #ifdef LPC1768_ENABLE_CLKOUT_12M + /** + * CLKOUTCFG register + * bit 8 (CLKOUT_EN) = enables CLKOUT signal. Disabled for now to prevent glitch when enabling GPIO. + * bits 7:4 (CLKOUTDIV) = set to 0 for divider setting of /1 + * bits 3:0 (CLKOUTSEL) = set to 1 to select main crystal oscillator as CLKOUT source + */ + LPC_SC->CLKOUTCFG = (0<<8)|(0<<4)|(1<<0); + // set P1.27 pin to function 01 (CLKOUT) + PINSEL_CFG_Type PinCfg; + PinCfg.Portnum = 1; + PinCfg.Pinnum = 27; + PinCfg.Funcnum = 1; // function 01 (CLKOUT) + PinCfg.OpenDrain = 0; // not open drain + PinCfg.Pinmode = 2; // no pull-up/pull-down + PINSEL_ConfigPin(&PinCfg); + // now set CLKOUT_EN bit + LPC_SC->CLKOUTCFG |= (1<<8); + #endif + USB_Init(); // USB Initialization USB_Connect(FALSE); // USB clear connection delay(1000); // Give OS time to notice diff --git a/Marlin/src/HAL/HAL_LPC1768/persistent_store_sdcard.cpp b/Marlin/src/HAL/HAL_LPC1768/persistent_store_sdcard.cpp index b120769041..2454dea195 100644 --- a/Marlin/src/HAL/HAL_LPC1768/persistent_store_sdcard.cpp +++ b/Marlin/src/HAL/HAL_LPC1768/persistent_store_sdcard.cpp @@ -125,7 +125,7 @@ static void debug_rw(const bool write, int &pos, const uint8_t *value, const siz // FR_INVALID_PARAMETER /* (19) Given parameter is invalid */ // } FRESULT; -bool PersistentStore::write_data(int &pos, const uint8_t *value, const size_t size, uint16_t *crc) { +bool PersistentStore::write_data(int &pos, const uint8_t *value, size_t size, uint16_t *crc) { if (!eeprom_file_open) return true; FRESULT s; UINT bytes_written = 0; diff --git a/Marlin/src/HAL/HAL_LPC1768/pinsDebug.h b/Marlin/src/HAL/HAL_LPC1768/pinsDebug.h index d14b14385c..e39f2d2453 100644 --- a/Marlin/src/HAL/HAL_LPC1768/pinsDebug.h +++ b/Marlin/src/HAL/HAL_LPC1768/pinsDebug.h @@ -32,9 +32,8 @@ #define digitalRead_mod(p) extDigitalRead(p) #define PRINT_PORT(p) #define GET_ARRAY_PIN(p) pin_array[p].pin -#define NAME_FORMAT(p) PSTR("%-##p##s") -#define PRINT_ARRAY_NAME(x) do {sprintf_P(buffer, PSTR("%-" STRINGIFY(MAX_NAME_LENGTH) "s"), pin_array[x].name); SERIAL_ECHO(buffer);} while (0) -#define PRINT_PIN(p) do {sprintf_P(buffer, PSTR("%d.%02d"), LPC1768_PIN_PORT(p), LPC1768_PIN_PIN(p)); SERIAL_ECHO(buffer);} while (0) +#define PRINT_ARRAY_NAME(x) do{ sprintf_P(buffer, PSTR("%-" STRINGIFY(MAX_NAME_LENGTH) "s"), pin_array[x].name); SERIAL_ECHO(buffer); }while(0) +#define PRINT_PIN(p) do{ sprintf_P(buffer, PSTR("%d.%02d"), LPC1768_PIN_PORT(p), LPC1768_PIN_PIN(p)); SERIAL_ECHO(buffer); }while(0) #define MULTI_NAME_PAD 16 // space needed to be pretty if not first name assigned to a pin // pins that will cause hang/reset/disconnect in M43 Toggle and Watch utilities diff --git a/Marlin/src/HAL/HAL_LPC1768/spi_pins.h b/Marlin/src/HAL/HAL_LPC1768/spi_pins.h index 2e17abd31c..acf991a9d7 100644 --- a/Marlin/src/HAL/HAL_LPC1768/spi_pins.h +++ b/Marlin/src/HAL/HAL_LPC1768/spi_pins.h @@ -25,7 +25,7 @@ #if ENABLED(SDSUPPORT) && HAS_GRAPHICAL_LCD && (LCD_PINS_D4 == SCK_PIN || LCD_PINS_ENABLE == MOSI_PIN || DOGLCD_SCK == SCK_PIN || DOGLCD_MOSI == MOSI_PIN) #define LPC_SOFTWARE_SPI // If the SD card and LCD adapter share the same SPI pins, then software SPI is currently - // needed due to the speed and mode requred for communicating with each device being different. + // needed due to the speed and mode required for communicating with each device being different. // This requirement can be removed if the SPI access to these devices is updated to use // spiBeginTransaction. #endif diff --git a/Marlin/src/HAL/HAL_SAMD51/HAL.cpp b/Marlin/src/HAL/HAL_SAMD51/HAL.cpp new file mode 100644 index 0000000000..32a6bad4cd --- /dev/null +++ b/Marlin/src/HAL/HAL_SAMD51/HAL.cpp @@ -0,0 +1,475 @@ +/** + * Marlin 3D Printer Firmware + * + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * SAMD51 HAL developed by Giuliano Zaro (AKA GMagician) + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + +#ifdef __SAMD51__ + +#include "../../inc/MarlinConfig.h" +#include "Adafruit_ZeroDMA.h" +#include "wiring_private.h" + +// ------------------------ +// Local defines +// ------------------------ + +#if HAS_TEMP_ADC_0 + #define GET_TEMP_0_ADC() PIN_TO_ADC(TEMP_0_PIN) +#else + #define GET_TEMP_0_ADC() -1 +#endif +#if HAS_TEMP_ADC_1 + #define GET_TEMP_1_ADC() PIN_TO_ADC(TEMP_1_PIN) +#else + #define GET_TEMP_1_ADC() -1 +#endif +#if HAS_TEMP_ADC_2 + #define GET_TEMP_2_ADC() PIN_TO_ADC(TEMP_2_PIN) +#else + #define GET_TEMP_2_ADC() -1 +#endif +#if HAS_TEMP_ADC_3 + #define GET_TEMP_3_ADC() PIN_TO_ADC(TEMP_3_PIN) +#else + #define GET_TEMP_3_ADC() -1 +#endif +#if HAS_TEMP_ADC_4 + #define GET_TEMP_4_ADC() PIN_TO_ADC(TEMP_4_PIN) +#else + #define GET_TEMP_4_ADC() -1 +#endif +#if HAS_TEMP_ADC_5 + #define GET_TEMP_5_ADC() PIN_TO_ADC(TEMP_5_PIN) +#else + #define GET_TEMP_5_ADC() -1 +#endif +#if HAS_HEATED_BED + #define GET_BED_ADC() PIN_TO_ADC(TEMP_BED_PIN) +#else + #define GET_BED_ADC() -1 +#endif +#if HAS_HEATED_CHAMBER + #define GET_CHAMBER_ADC() PIN_TO_ADC(TEMP_CHAMBER_PIN) +#else + #define GET_CHAMBER_ADC() -1 +#endif +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define GET_FILAMENT_WIDTH_ADC() PIN_TO_ADC(FILWIDTH_PIN) +#else + #define GET_FILAMENT_WIDTH_ADC() -1 +#endif +#if HAS_ADC_BUTTONS + #define GET_BUTTONS_ADC() PIN_TO_ADC(ADC_KEYPAD_PIN) +#else + #define GET_BUTTONS_ADC() -1 +#endif + +#define IS_ADC_REQUIRED(n) (GET_TEMP_0_ADC() == n || GET_TEMP_1_ADC() == n || GET_TEMP_2_ADC() == n \ + || GET_TEMP_3_ADC() == n || GET_TEMP_4_ADC() == n || GET_TEMP_5_ADC() == n \ + || GET_BED_ADC() == n \ + || GET_CHAMBER_ADC() == n \ + || GET_FILAMENT_WIDTH_ADC() == n \ + || GET_BUTTONS_ADC() == n) + +#define ADC0_IS_REQUIRED IS_ADC_REQUIRED(0) +#define ADC1_IS_REQUIRED IS_ADC_REQUIRED(1) +#define ADC_IS_REQUIRED (ADC0_IS_REQUIRED || ADC1_IS_REQUIRED) +#if ADC0_IS_REQUIRED + #define FIRST_ADC 0 +#else + #define FIRST_ADC 1 +#endif +#if ADC1_IS_REQUIRED + #define LAST_ADC 1 +#else + #define LAST_ADC 0 +#endif + +#define DMA_IS_REQUIRED ADC_IS_REQUIRED + +// ------------------------ +// Types +// ------------------------ + +#if DMA_IS_REQUIRED + + // Struct must be 32 bits aligned because of DMA accesses but fields needs to be 8 bits packed + typedef struct __attribute__((aligned(4), packed)) { + ADC_INPUTCTRL_Type INPUTCTRL; + } HAL_DMA_DAC_Registers; // DMA transfered registers + +#endif + +// ------------------------ +// Private Variables +// ------------------------ + +uint16_t HAL_adc_result; + +#if ADC_IS_REQUIRED + + // Pins used by ADC inputs. Order must be ADC0 inputs first then ADC1 + const uint8_t adc_pins[] = { + // ADC0 pins + #if GET_TEMP_0_ADC() == 0 + TEMP_0_PIN, + #endif + #if GET_TEMP_1_ADC() == 0 + TEMP_1_PIN, + #endif + #if GET_TEMP_2_ADC() == 0 + TEMP_2_PIN, + #endif + #if GET_TEMP_3_ADC() == 0 + TEMP_3_PIN, + #endif + #if GET_TEMP_4_ADC() == 0 + TEMP_4_PIN, + #endif + #if GET_TEMP_5_ADC() == 0 + TEMP_5_PIN, + #endif + #if GET_BED_ADC() == 0 + TEMP_BED_PIN, + #endif + #if GET_CHAMBER_ADC() == 0 + TEMP_CHAMBER_PIN, + #endif + #if GET_FILAMENT_WIDTH_ADC() == 0 + FILWIDTH_PIN, + #endif + #if GET_BUTTONS_ADC() == 0 + ADC_KEYPAD_PIN, + #endif + // ADC1 pins + #if GET_TEMP_0_ADC() == 1 + TEMP_0_PIN, + #endif + #if GET_TEMP_1_ADC() == 1 + TEMP_1_PIN, + #endif + #if GET_TEMP_2_ADC() == 1 + TEMP_2_PIN, + #endif + #if GET_TEMP_3_ADC() == 1 + TEMP_3_PIN, + #endif + #if GET_TEMP_4_ADC() == 1 + TEMP_4_PIN, + #endif + #if GET_TEMP_5_ADC() == 1 + TEMP_5_PIN, + #endif + #if GET_BED_ADC() == 1 + TEMP_BED_PIN, + #endif + #if GET_CHAMBER_ADC() == 1 + TEMP_CHAMBER_PIN, + #endif + #if GET_FILAMENT_WIDTH_ADC() == 1 + FILWIDTH_PIN, + #endif + #if GET_BUTTONS_ADC() == 1 + ADC_KEYPAD_PIN, + #endif + }; + + uint16_t HAL_adc_results[COUNT(adc_pins)]; + + #if ADC0_IS_REQUIRED + Adafruit_ZeroDMA adc0DMAProgram, + adc0DMARead; + + const HAL_DMA_DAC_Registers adc0_dma_regs_list[] = { + #if GET_TEMP_0_ADC() == 0 + { PIN_TO_INPUTCTRL(TEMP_0_PIN) }, + #endif + #if GET_TEMP_1_ADC() == 0 + { PIN_TO_INPUTCTRL(TEMP_1_PIN) }, + #endif + #if GET_TEMP_2_ADC() == 0 + { PIN_TO_INPUTCTRL(TEMP_2_PIN) }, + #endif + #if GET_TEMP_3_ADC() == 0 + { PIN_TO_INPUTCTRL(TEMP_3_PIN) }, + #endif + #if GET_TEMP_4_ADC() == 0 + { PIN_TO_INPUTCTRL(TEMP_4_PIN) }, + #endif + #if GET_TEMP_5_ADC() == 0 + { PIN_TO_INPUTCTRL(TEMP_5_PIN) }, + #endif + #if GET_BED_ADC() == 0 + { PIN_TO_INPUTCTRL(TEMP_BED_PIN) }, + #endif + #if GET_CHAMBER_ADC() == 0 + { PIN_TO_INPUTCTRL(TEMP_CHAMBER_PIN) }, + #endif + #if GET_FILAMENT_WIDTH_ADC() == 0 + { PIN_TO_INPUTCTRL(FILWIDTH_PIN) }, + #endif + #if GET_BUTTONS_ADC() == 0 + { PIN_TO_INPUTCTRL(ADC_KEYPAD_PIN) }, + #endif + }; + + #define ADC0_AINCOUNT COUNT(adc0_dma_regs_list) + #endif // ADC0_IS_REQUIRED + + #if ADC1_IS_REQUIRED + Adafruit_ZeroDMA adc1DMAProgram, + adc1DMARead; + + const HAL_DMA_DAC_Registers adc1_dma_regs_list[] = { + #if GET_TEMP_0_ADC() == 1 + { PIN_TO_INPUTCTRL(TEMP_0_PIN) }, + #endif + #if GET_TEMP_1_ADC() == 1 + { PIN_TO_INPUTCTRL(TEMP_1_PIN) }, + #endif + #if GET_TEMP_2_ADC() == 1 + { PIN_TO_INPUTCTRL(TEMP_2_PIN) }, + #endif + #if GET_TEMP_3_ADC() == 1 + { PIN_TO_INPUTCTRL(TEMP_3_PIN) }, + #endif + #if GET_TEMP_4_ADC() == 1 + { PIN_TO_INPUTCTRL(TEMP_4_PIN) }, + #endif + #if GET_TEMP_5_ADC() == 1 + { PIN_TO_INPUTCTRL(TEMP_5_PIN) }, + #endif + #if GET_BED_ADC() == 1 + { PIN_TO_INPUTCTRL(TEMP_BED_PIN) }, + #endif + #if GET_CHAMBER_ADC() == 1 + { PIN_TO_INPUTCTRL(TEMP_CHAMBER_PIN) }, + #endif + #if GET_FILAMENT_WIDTH_ADC() == 1 + { PIN_TO_INPUTCTRL(FILWIDTH_PIN) }, + #endif + #if GET_BUTTONS_ADC() == 1 + { PIN_TO_INPUTCTRL(ADC_KEYPAD_PIN) }, + #endif + }; + + #define ADC1_AINCOUNT COUNT(adc1_dma_regs_list) + #endif // ADC1_IS_REQUIRED + +#endif // ADC_IS_REQUIRED + +// ------------------------ +// Private functions +// ------------------------ + +#if DMA_IS_REQUIRED + + void dma_init() { + DmacDescriptor *descriptor; + + #if ADC0_IS_REQUIRED + adc0DMAProgram.setTrigger(ADC0_DMAC_ID_SEQ); + adc0DMAProgram.setAction(DMA_TRIGGER_ACTON_BEAT); + adc0DMAProgram.loop(true); + if (adc0DMAProgram.allocate() == DMA_STATUS_OK) { + descriptor = adc0DMAProgram.addDescriptor( + (void *)adc0_dma_regs_list, // SRC + (void *)&ADC0->DSEQDATA.reg, // DEST + sizeof(adc0_dma_regs_list) / 4, // CNT + DMA_BEAT_SIZE_WORD, + true, // SRCINC + false, // DSTINC + DMA_ADDRESS_INCREMENT_STEP_SIZE_1, // STEPSIZE + DMA_STEPSEL_SRC // STEPSEL + ); + if (descriptor != nullptr) + descriptor->BTCTRL.bit.EVOSEL = DMA_EVENT_OUTPUT_BEAT; + adc0DMAProgram.startJob(); + } + + adc0DMARead.setTrigger(ADC0_DMAC_ID_RESRDY); + adc0DMARead.setAction(DMA_TRIGGER_ACTON_BEAT); + adc0DMARead.loop(true); + if (adc0DMARead.allocate() == DMA_STATUS_OK) { + adc0DMARead.addDescriptor( + (void *)&ADC0->RESULT.reg, // SRC + &HAL_adc_results, // DEST + ADC0_AINCOUNT, // CNT + DMA_BEAT_SIZE_HWORD, + false, // SRCINC + true, // DSTINC + DMA_ADDRESS_INCREMENT_STEP_SIZE_1, // STEPSIZE + DMA_STEPSEL_DST // STEPSEL + ); + adc0DMARead.startJob(); + } + #endif + #if ADC1_IS_REQUIRED + adc1DMAProgram.setTrigger(ADC1_DMAC_ID_SEQ); + adc1DMAProgram.setAction(DMA_TRIGGER_ACTON_BEAT); + adc1DMAProgram.loop(true); + if (adc1DMAProgram.allocate() == DMA_STATUS_OK) { + descriptor = adc1DMAProgram.addDescriptor( + (void *)adc1_dma_regs_list, // SRC + (void *)&ADC1->DSEQDATA.reg, // DEST + sizeof(adc1_dma_regs_list) / 4, // CNT + DMA_BEAT_SIZE_WORD, + true, // SRCINC + false, // DSTINC + DMA_ADDRESS_INCREMENT_STEP_SIZE_1, // STEPSIZE + DMA_STEPSEL_SRC // STEPSEL + ); + if (descriptor != nullptr) + descriptor->BTCTRL.bit.EVOSEL = DMA_EVENT_OUTPUT_BEAT; + adc1DMAProgram.startJob(); + } + + adc1DMARead.setTrigger(ADC1_DMAC_ID_RESRDY); + adc1DMARead.setAction(DMA_TRIGGER_ACTON_BEAT); + adc1DMARead.loop(true); + if (adc1DMARead.allocate() == DMA_STATUS_OK) { + adc1DMARead.addDescriptor( + (void *)&ADC1->RESULT.reg, // SRC + &HAL_adc_results[ADC0_AINCOUNT], // DEST + ADC1_AINCOUNT, // CNT + DMA_BEAT_SIZE_HWORD, + false, // SRCINC + true, // DSTINC + DMA_ADDRESS_INCREMENT_STEP_SIZE_1, // STEPSIZE + DMA_STEPSEL_DST // STEPSEL + ); + adc1DMARead.startJob(); + } + #endif + + DMAC->PRICTRL0.bit.RRLVLEN0 = true; // Activate round robin for DMA channels required by ADCs + } + +#endif // DMA_IS_REQUIRED + +// ------------------------ +// Public functions +// ------------------------ + +// HAL initialization task +void HAL_init(void) { + #if DMA_IS_REQUIRED + dma_init(); + #endif + #if ENABLED(SDSUPPORT) + #if SD_CONNECTION_IS(ONBOARD) && PIN_EXISTS(SD_DETECT) // SD_DETECT_PIN may be remove when NO_SD_HOST_DRIVE is not defined in configuration_adv + SET_INPUT_PULLUP(SD_DETECT_PIN); + #endif + OUT_WRITE(SDSS, HIGH); // Try to set SDSS inactive before any other SPI users start up + #endif +} + +// HAL idle task +/* +void HAL_idletask(void) { +} +*/ + +void HAL_clear_reset_source(void) { } + +#pragma push_macro("WDT") +#undef WDT // Required to be able to use '.bit.WDT'. Compiler wrongly replace struct field with WDT define +uint8_t HAL_get_reset_source(void) { + RSTC_RCAUSE_Type resetCause; + + resetCause.reg = REG_RSTC_RCAUSE; + if (resetCause.bit.POR) return RST_POWER_ON; + else if (resetCause.bit.EXT) return RST_EXTERNAL; + else if (resetCause.bit.BODCORE || resetCause.bit.BODVDD) return RST_BROWN_OUT; + else if (resetCause.bit.WDT) return RST_WATCHDOG; + else if (resetCause.bit.SYST || resetCause.bit.NVM) return RST_SOFTWARE; + else if (resetCause.bit.BACKUP) return RST_BACKUP; + return 0; +} +#pragma pop_macro("WDT") + +extern "C" { + void * _sbrk(int incr); + + extern unsigned int __bss_end__; // end of bss section +} + +// Return free memory between end of heap (or end bss) and whatever is current +int freeMemory() { + int free_memory, heap_end = (int)_sbrk(0); + return (int)&free_memory - (heap_end ? heap_end : (int)&__bss_end__); +} + +// ------------------------ +// ADC +// ------------------------ + +void HAL_adc_init(void) { + #if ADC_IS_REQUIRED + memset(HAL_adc_results, 0xFF, sizeof(HAL_adc_results)); // Fill result with invalid values + + for (uint8_t pi = 0; pi < COUNT(adc_pins); ++pi) + pinPeripheral(adc_pins[pi], PIO_ANALOG); + + for (uint8_t ai = FIRST_ADC; ai <= LAST_ADC; ++ai) { + Adc* adc = ((Adc*[])ADC_INSTS)[ai]; + + // ADC clock setup + GCLK->PCHCTRL[ADC0_GCLK_ID + ai].bit.CHEN = false; + SYNC(GCLK->PCHCTRL[ADC0_GCLK_ID + ai].bit.CHEN); + GCLK->PCHCTRL[ADC0_GCLK_ID + ai].reg = GCLK_PCHCTRL_GEN_GCLK1 | GCLK_PCHCTRL_CHEN; // 48MHz startup code programmed + SYNC(!GCLK->PCHCTRL[ADC0_GCLK_ID + ai].bit.CHEN); + adc->CTRLA.bit.PRESCALER = ADC_CTRLA_PRESCALER_DIV32_Val; // 1.5MHZ adc clock + + // ADC setup + // Preloaded data (fixed for all ADC instances hence not loaded by DMA) + adc->REFCTRL.bit.REFSEL = ADC_REFCTRL_REFSEL_AREFA_Val; // VRefA pin + SYNC(adc->SYNCBUSY.bit.REFCTRL); + adc->CTRLB.bit.RESSEL = ADC_CTRLB_RESSEL_10BIT_Val; + SYNC(adc->SYNCBUSY.bit.CTRLB); + adc->SAMPCTRL.bit.SAMPLEN = (6 - 1); // Sampling clocks + // Registers loaded by DMA + adc->DSEQCTRL.bit.INPUTCTRL = true; + + adc->DSEQCTRL.bit.AUTOSTART = true; // Start conversion after DMA sequence + + adc->CTRLA.bit.ENABLE = true; // Enable ADC + SYNC(adc->SYNCBUSY.bit.ENABLE); + } + #endif // ADC_IS_REQUIRED +} + +void HAL_adc_start_conversion(const uint8_t adc_pin) { + #if ADC_IS_REQUIRED + for (uint8_t pi = 0; pi < COUNT(adc_pins); ++pi) { + if (adc_pin == adc_pins[pi]) { + HAL_adc_result = HAL_adc_results[pi]; + return; + } + } + #endif + + HAL_adc_result = 0xFFFF; +} + +uint16_t HAL_adc_get_result(void) { + return HAL_adc_result; +} + +#endif // __SAMD51__ diff --git a/Marlin/src/HAL/HAL_SAMD51/HAL.h b/Marlin/src/HAL/HAL_SAMD51/HAL.h new file mode 100644 index 0000000000..ca51e40d8f --- /dev/null +++ b/Marlin/src/HAL/HAL_SAMD51/HAL.h @@ -0,0 +1,142 @@ +/** + * Marlin 3D Printer Firmware + * + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * SAMD51 HAL developed by Giuliano Zaro (AKA GMagician) + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +#define CPU_32_BIT + +#include "../shared/Marduino.h" +#include "../shared/math_32bit.h" +#include "../shared/HAL_SPI.h" +#include "fastio_SAMD51.h" +#include "watchdog_SAMD51.h" +#include "HAL_timers_SAMD51.h" + +#ifdef ADAFRUIT_GRAND_CENTRAL_M4 + #include "MarlinSerial_AGCM4.h" + + // Serial ports + #if !WITHIN(SERIAL_PORT, -1, 3) + #error "SERIAL_PORT must be from -1 to 3" + #endif + + // MYSERIAL0 required before MarlinSerial includes! + #if SERIAL_PORT == -1 + #define MYSERIAL0 Serial + #elif SERIAL_PORT == 0 + #define MYSERIAL0 Serial1 + #elif SERIAL_PORT == 1 + #define MYSERIAL0 Serial2 + #elif SERIAL_PORT == 2 + #define MYSERIAL0 Serial3 + #else + #define MYSERIAL0 Serial4 + #endif + + #ifdef SERIAL_PORT_2 + #if !WITHIN(SERIAL_PORT_2, -1, 3) + #error "SERIAL_PORT_2 must be from -1 to 3" + #elif SERIAL_PORT_2 == SERIAL_PORT + #error "SERIAL_PORT_2 must be different than SERIAL_PORT" + #endif + #define NUM_SERIAL 2 + #if SERIAL_PORT_2 == -1 + #define MYSERIAL1 Serial + #elif SERIAL_PORT_2 == 0 + #define MYSERIAL1 Serial1 + #elif SERIAL_PORT_2 == 1 + #define MYSERIAL1 Serial2 + #elif SERIAL_PORT_2 == 2 + #define MYSERIAL1 Serial3 + #else + #define MYSERIAL1 Serial4 + #endif + #else + #define NUM_SERIAL 1 + #endif + +#endif // ADAFRUIT_GRAND_CENTRAL_M4 + +typedef int8_t pin_t; + +#define SHARED_SERVOS HAS_SERVOS +#define HAL_SERVO_LIB Servo + +// +// Interrupts +// +#define CRITICAL_SECTION_START uint32_t primask = __get_PRIMASK(); __disable_irq() +#define CRITICAL_SECTION_END if (!primask) __enable_irq() +#define ISRS_ENABLED() (!__get_PRIMASK()) +#define ENABLE_ISRS() __enable_irq() +#define DISABLE_ISRS() __disable_irq() + +#define cli() __disable_irq() // Disable interrupts +#define sei() __enable_irq() // Enable interrupts + +void HAL_clear_reset_source(void); // clear reset reason +uint8_t HAL_get_reset_source(void); // get reset reason + +// +// EEPROM +// +void eeprom_write_byte(uint8_t *pos, unsigned char value); +uint8_t eeprom_read_byte(uint8_t *pos); + +// +// ADC +// +extern uint16_t HAL_adc_result; // result of last ADC conversion + +#define HAL_ANALOG_SELECT(pin) + +void HAL_adc_init(void); + +#define HAL_START_ADC(pin) HAL_adc_start_conversion(pin) +#define HAL_READ_ADC() HAL_adc_result +#define HAL_ADC_READY() true + +void HAL_adc_start_conversion(const uint8_t adc_pin); +uint16_t HAL_adc_get_result(void); + +// +// Pin Map +// +#define GET_PIN_MAP_PIN(index) index +#define GET_PIN_MAP_INDEX(pin) pin +#define PARSED_PIN_INDEX(code, dval) parser.intval(code, dval) + +// +// Tone +// +void toneInit(); +void tone(const pin_t _pin, const unsigned int frequency, const unsigned long duration=0); +void noTone(const pin_t _pin); + +// Enable hooks into idle and setup for HAL +void HAL_init(void); +/*#define HAL_IDLETASK 1 +void HAL_idletask(void);*/ + +// +// Utility functions +// +FORCE_INLINE void _delay_ms(const int delay_ms) { delay(delay_ms); } +int freeMemory(void); diff --git a/Marlin/src/HAL/HAL_SAMD51/HAL_spi_SAMD51.cpp b/Marlin/src/HAL/HAL_SAMD51/HAL_spi_SAMD51.cpp new file mode 100644 index 0000000000..5235d56cf9 --- /dev/null +++ b/Marlin/src/HAL/HAL_SAMD51/HAL_spi_SAMD51.cpp @@ -0,0 +1,151 @@ +/** + * Marlin 3D Printer Firmware + * + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * SAMD51 HAL developed by Giuliano Zaro (AKA GMagician) + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + +/** + * Hardware and software SPI implementations are included in this file. + * + * Control of the slave select pin(s) is handled by the calling routines and + * SAMD51 let hardware SPI handling to remove SS from its logic. + */ + +#ifdef __SAMD51__ + +// -------------------------------------------------------------------------- +// Includes +// -------------------------------------------------------------------------- + +#include "../../inc/MarlinConfig.h" +#include + +// -------------------------------------------------------------------------- +// Public functions +// -------------------------------------------------------------------------- + +#if EITHER(SOFTWARE_SPI, FORCE_SOFT_SPI) + + // ------------------------ + // Software SPI + // ------------------------ + #error "Software SPI not supported for SAMD51. Use Hardware SPI." + + #if SD_CONNECTION_IS(ONBOARD) + #endif + +#else // !SOFTWARE_SPI + + #ifdef ADAFRUIT_GRAND_CENTRAL_M4 + #if SD_CONNECTION_IS(ONBOARD) + #define sdSPI SDCARD_SPI + #else + #define sdSPI SPI + #endif + #endif + + static SPISettings spiConfig; + + // ------------------------ + // Hardware SPI + // ------------------------ + void spiBegin(void) { + spiInit(SPI_HALF_SPEED); + } + + void spiInit(uint8_t spiRate) { + // Use datarates Marlin uses + uint32_t clock; + switch (spiRate) { + case SPI_FULL_SPEED: clock = 8000000; break; + case SPI_HALF_SPEED: clock = 4000000; break; + case SPI_QUARTER_SPEED: clock = 2000000; break; + case SPI_EIGHTH_SPEED: clock = 1000000; break; + case SPI_SIXTEENTH_SPEED: clock = 500000; break; + case SPI_SPEED_5: clock = 250000; break; + case SPI_SPEED_6: clock = 125000; break; + default: clock = 4000000; break; // Default from the SPI library + } + spiConfig = SPISettings(clock, MSBFIRST, SPI_MODE0); + sdSPI.begin(); + } + + /** + * @brief Receives a single byte from the SPI port. + * + * @return Byte received + * + * @details + */ + uint8_t spiRec(void) { + sdSPI.beginTransaction(spiConfig); + uint8_t returnByte = sdSPI.transfer(0xFF); + sdSPI.endTransaction(); + return returnByte; + } + + /** + * @brief Receives a number of bytes from the SPI port to a buffer + * + * @param buf Pointer to starting address of buffer to write to. + * @param nbyte Number of bytes to receive. + * @return Nothing + */ + void spiRead(uint8_t* buf, uint16_t nbyte) { + if (nbyte == 0) return; + memset(buf, 0xFF, nbyte); + sdSPI.beginTransaction(spiConfig); + sdSPI.transfer(buf, nbyte); + sdSPI.endTransaction(); + } + + /** + * @brief Sends a single byte on SPI port + * + * @param b Byte to send + * + * @details + */ + void spiSend(uint8_t b) { + sdSPI.beginTransaction(spiConfig); + sdSPI.transfer(b); + sdSPI.endTransaction(); + } + + /** + * @brief Write token and then write from 512 byte buffer to SPI (for SD card) + * + * @param buf Pointer with buffer start address + * @return Nothing + * + * @details Uses DMA + */ + void spiSendBlock(uint8_t token, const uint8_t* buf) { + sdSPI.beginTransaction(spiConfig); + sdSPI.transfer(token); + sdSPI.transfer((uint8_t*)buf, nullptr, 512); + sdSPI.endTransaction(); + } + + void spiBeginTransaction(uint32_t spiClock, uint8_t bitOrder, uint8_t dataMode) { + spiConfig = SPISettings(spiClock, (BitOrder)bitOrder, dataMode); + sdSPI.beginTransaction(spiConfig); + } +#endif // !SOFTWARE_SPI + +#endif // __SAMD51__ diff --git a/Marlin/src/HAL/HAL_SAMD51/HAL_timers_SAMD51.cpp b/Marlin/src/HAL/HAL_SAMD51/HAL_timers_SAMD51.cpp new file mode 100644 index 0000000000..ea02e839fe --- /dev/null +++ b/Marlin/src/HAL/HAL_SAMD51/HAL_timers_SAMD51.cpp @@ -0,0 +1,135 @@ +/** + * Marlin 3D Printer Firmware + * + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * SAMD51 HAL developed by Giuliano Zaro (AKA GMagician) + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + +#ifdef __SAMD51__ + +// -------------------------------------------------------------------------- +// Includes +// -------------------------------------------------------------------------- +#include "../../inc/MarlinConfig.h" +#include "HAL_timers_SAMD51.h" + +// -------------------------------------------------------------------------- +// Local defines +// -------------------------------------------------------------------------- + +#define NUM_HARDWARE_TIMERS 8 + +// -------------------------------------------------------------------------- +// Private Variables +// -------------------------------------------------------------------------- + +const tTimerConfig TimerConfig[NUM_HARDWARE_TIMERS] = { + { TC0, TC0_IRQn, TC_PRIORITY(0) }, + { TC1, TC1_IRQn, TC_PRIORITY(1) }, + { TC2, TC2_IRQn, TC_PRIORITY(2) }, // Reserved by framework tone function + { TC3, TC3_IRQn, TC_PRIORITY(3) }, // Reserved by servo library + { TC4, TC4_IRQn, TC_PRIORITY(4) }, + { TC5, TC5_IRQn, TC_PRIORITY(5) }, + { TC6, TC6_IRQn, TC_PRIORITY(6) }, + { TC7, TC7_IRQn, TC_PRIORITY(7) } +}; + +// -------------------------------------------------------------------------- +// Private functions +// -------------------------------------------------------------------------- + +FORCE_INLINE void Disable_Irq(IRQn_Type irq) { + NVIC_DisableIRQ(irq); + + // We NEED memory barriers to ensure Interrupts are actually disabled! + // ( https://dzone.com/articles/nvic-disabling-interrupts-on-arm-cortex-m-and-the ) + __DSB(); + __ISB(); +} + +// -------------------------------------------------------------------------- +// Public functions +// -------------------------------------------------------------------------- + +void HAL_timer_start(const uint8_t timer_num, const uint32_t frequency) { + Tc * const tc = TimerConfig[timer_num].pTimer; + IRQn_Type irq = TimerConfig[timer_num].IRQ_Id; + + // Disable interrupt, just in case it was already enabled + Disable_Irq(irq); + + // Disable timer interrupt + tc->COUNT32.INTENCLR.reg = TC_INTENCLR_OVF; // disable overflow interrupt + + // TCn clock setup + const uint8_t clockID = GCLK_CLKCTRL_IDs[TCC_INST_NUM + timer_num]; + GCLK->PCHCTRL[clockID].bit.CHEN = false; + SYNC(GCLK->PCHCTRL[clockID].bit.CHEN); + GCLK->PCHCTRL[clockID].reg = GCLK_PCHCTRL_GEN_GCLK0 | GCLK_PCHCTRL_CHEN; // 120MHz startup code programmed + SYNC(!GCLK->PCHCTRL[clockID].bit.CHEN); + + // Stop timer, just in case, to be able to reconfigure it + tc->COUNT32.CTRLA.bit.ENABLE = false; + SYNC(tc->COUNT32.SYNCBUSY.bit.ENABLE); + + // Reset timer + tc->COUNT32.CTRLA.bit.SWRST = true; + SYNC(tc->COUNT32.SYNCBUSY.bit.SWRST); + + NVIC_SetPriority(irq, TimerConfig[timer_num].priority); + + // Wave mode, reset counter on overflow on 0 (I use count down to prevent double buffer use) + tc->COUNT32.WAVE.reg = TC_WAVE_WAVEGEN_MFRQ; + tc->COUNT32.CTRLA.reg = TC_CTRLA_MODE_COUNT32 | TC_CTRLA_PRESCALER_DIV1; + tc->COUNT32.CTRLBSET.reg = TC_CTRLBCLR_DIR; + SYNC(tc->COUNT32.SYNCBUSY.bit.CTRLB); + + // Set compare value + tc->COUNT32.COUNT.reg = tc->COUNT32.CC[0].reg = HAL_TIMER_RATE / frequency; + + // And start timer + tc->COUNT32.CTRLA.bit.ENABLE = true; + SYNC(tc->COUNT32.SYNCBUSY.bit.ENABLE); + + // Enable interrupt on RC compare + tc->COUNT32.INTENSET.reg = TC_INTENCLR_OVF; // enable overflow interrupt + + // Finally, enable IRQ + NVIC_EnableIRQ(irq); +} + +void HAL_timer_enable_interrupt(const uint8_t timer_num) { + IRQn_Type irq = TimerConfig[timer_num].IRQ_Id; + NVIC_EnableIRQ(irq); +} + +void HAL_timer_disable_interrupt(const uint8_t timer_num) { + IRQn_Type irq = TimerConfig[timer_num].IRQ_Id; + Disable_Irq(irq); +} + +// missing from CMSIS: Check if interrupt is enabled or not +static bool NVIC_GetEnabledIRQ(IRQn_Type IRQn) { + return (NVIC->ISER[(uint32_t)(IRQn) >> 5] & (1 << ((uint32_t)(IRQn) & 0x1F))) != 0; +} + +bool HAL_timer_interrupt_enabled(const uint8_t timer_num) { + IRQn_Type irq = TimerConfig[timer_num].IRQ_Id; + return NVIC_GetEnabledIRQ(irq); +} + +#endif // __SAMD51__ diff --git a/Marlin/src/HAL/HAL_SAMD51/HAL_timers_SAMD51.h b/Marlin/src/HAL/HAL_SAMD51/HAL_timers_SAMD51.h new file mode 100644 index 0000000000..80c37d14af --- /dev/null +++ b/Marlin/src/HAL/HAL_SAMD51/HAL_timers_SAMD51.h @@ -0,0 +1,116 @@ +/** + * Marlin 3D Printer Firmware + * + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * SAMD51 HAL developed by Giuliano Zaro (AKA GMagician) + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +#include + +// -------------------------------------------------------------------------- +// Defines +// -------------------------------------------------------------------------- + +typedef uint32_t hal_timer_t; +#define HAL_TIMER_TYPE_MAX 0xFFFFFFFF + +#define HAL_TIMER_RATE SystemCoreClock // frequency of timers peripherals + +#define STEP_TIMER_NUM 0 // index of timer to use for stepper (also +1 for 32bits counter) +#define PULSE_TIMER_NUM STEP_TIMER_NUM +#define TEMP_TIMER_NUM 4 // index of timer to use for temperature (also +1 for 32bits counter) + +#define TEMP_TIMER_FREQUENCY 1000 // temperature interrupt frequency + +#define STEPPER_TIMER_RATE HAL_TIMER_RATE // frequency of stepper timer (HAL_TIMER_RATE / STEPPER_TIMER_PRESCALE) +#define STEPPER_TIMER_TICKS_PER_US ((STEPPER_TIMER_RATE) / 1000000) // stepper timer ticks per µs +#define STEPPER_TIMER_PRESCALE (CYCLES_PER_MICROSECOND / STEPPER_TIMER_TICKS_PER_US) + +#define PULSE_TIMER_RATE STEPPER_TIMER_RATE +#define PULSE_TIMER_PRESCALE STEPPER_TIMER_PRESCALE +#define PULSE_TIMER_TICKS_PER_US STEPPER_TIMER_TICKS_PER_US + +#define ENABLE_STEPPER_DRIVER_INTERRUPT() HAL_timer_enable_interrupt(STEP_TIMER_NUM) +#define DISABLE_STEPPER_DRIVER_INTERRUPT() HAL_timer_disable_interrupt(STEP_TIMER_NUM) +#define STEPPER_ISR_ENABLED() HAL_timer_interrupt_enabled(STEP_TIMER_NUM) + +#define ENABLE_TEMPERATURE_INTERRUPT() HAL_timer_enable_interrupt(TEMP_TIMER_NUM) +#define DISABLE_TEMPERATURE_INTERRUPT() HAL_timer_disable_interrupt(TEMP_TIMER_NUM) + +#define TC_PRIORITY(t) (t == STEP_TIMER_NUM || t == PULSE_TIMER_NUM) ? 2 \ + : (t == TEMP_TIMER_NUM) ? 6 \ + : 7 + +#define _TC_HANDLER(t) void TC##t##_Handler() +#define TC_HANDLER(t) _TC_HANDLER(t) +#define HAL_STEP_TIMER_ISR() TC_HANDLER(STEP_TIMER_NUM) +#if STEP_TIMER_NUM != PULSE_TIMER_NUM + #define HAL_PULSE_TIMER_ISR() TC_HANDLER(PULSE_TIMER_NUM) +#endif +#define HAL_TEMP_TIMER_ISR() TC_HANDLER(TEMP_TIMER_NUM) + +// -------------------------------------------------------------------------- +// Types +// -------------------------------------------------------------------------- + +typedef struct { + Tc *pTimer; + IRQn_Type IRQ_Id; + uint8_t priority; +} tTimerConfig; + +// -------------------------------------------------------------------------- +// Public Variables +// -------------------------------------------------------------------------- + +extern const tTimerConfig TimerConfig[]; + +// -------------------------------------------------------------------------- +// Public functions +// -------------------------------------------------------------------------- + +void HAL_timer_start(const uint8_t timer_num, const uint32_t frequency); + +FORCE_INLINE static void HAL_timer_set_compare(const uint8_t timer_num, const hal_timer_t compare) { + Tc * const tc = TimerConfig[timer_num].pTimer; + tc->COUNT32.CC[0].reg = HAL_TIMER_TYPE_MAX - compare; +} + +FORCE_INLINE static hal_timer_t HAL_timer_get_compare(const uint8_t timer_num) { + Tc * const tc = TimerConfig[timer_num].pTimer; + return (hal_timer_t)(HAL_TIMER_TYPE_MAX - tc->COUNT32.CC[0].reg); +} + +FORCE_INLINE static hal_timer_t HAL_timer_get_count(const uint8_t timer_num) { + Tc * const tc = TimerConfig[timer_num].pTimer; + tc->COUNT32.CTRLBSET.reg = TC_CTRLBCLR_CMD_READSYNC; + SYNC(tc->COUNT32.SYNCBUSY.bit.CTRLB || tc->COUNT32.SYNCBUSY.bit.COUNT); + return HAL_TIMER_TYPE_MAX - tc->COUNT32.COUNT.reg; +} + +void HAL_timer_enable_interrupt(const uint8_t timer_num); +void HAL_timer_disable_interrupt(const uint8_t timer_num); +bool HAL_timer_interrupt_enabled(const uint8_t timer_num); + +FORCE_INLINE static void HAL_timer_isr_prologue(const uint8_t timer_num) { + Tc * const tc = TimerConfig[timer_num].pTimer; + // Clear interrupt flag + tc->COUNT32.INTFLAG.reg = TC_INTFLAG_OVF; +} + +#define HAL_timer_isr_epilogue(timer_num) diff --git a/Marlin/src/HAL/HAL_SAMD51/MarlinSerial_AGCM4.cpp b/Marlin/src/HAL/HAL_SAMD51/MarlinSerial_AGCM4.cpp new file mode 100644 index 0000000000..2da4d8c07e --- /dev/null +++ b/Marlin/src/HAL/HAL_SAMD51/MarlinSerial_AGCM4.cpp @@ -0,0 +1,55 @@ +/** + * Marlin 3D Printer Firmware + * + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * SAMD51 HAL developed by Giuliano Zaro (AKA GMagician) + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + +#ifdef ADAFRUIT_GRAND_CENTRAL_M4 + +/** + * Framework doesn't define some serial to save sercom resources + * hence if these are used I need to define them + */ + +#include "../../inc/MarlinConfig.h" + +#if SERIAL_PORT == 1 || SERIAL_PORT_2 == 1 + Uart Serial2(&sercom4, PIN_SERIAL2_RX, PIN_SERIAL2_TX, PAD_SERIAL2_RX, PAD_SERIAL2_TX); + void SERCOM4_0_Handler() { Serial2.IrqHandler(); } + void SERCOM4_1_Handler() { Serial2.IrqHandler(); } + void SERCOM4_2_Handler() { Serial2.IrqHandler(); } + void SERCOM4_3_Handler() { Serial2.IrqHandler(); } +#endif + +#if SERIAL_PORT == 2 || SERIAL_PORT_2 == 2 + Uart Serial3(&sercom1, PIN_SERIAL3_RX, PIN_SERIAL3_TX, PAD_SERIAL3_RX, PAD_SERIAL3_TX); + void SERCOM1_0_Handler() { Serial3.IrqHandler(); } + void SERCOM1_1_Handler() { Serial3.IrqHandler(); } + void SERCOM1_2_Handler() { Serial3.IrqHandler(); } + void SERCOM1_3_Handler() { Serial3.IrqHandler(); } +#endif + +#if SERIAL_PORT == 3 || SERIAL_PORT_2 == 3 + Uart Serial4(&sercom5, PIN_SERIAL4_RX, PIN_SERIAL4_TX, PAD_SERIAL4_RX, PAD_SERIAL4_TX); + void SERCOM5_0_Handler() { Serial4.IrqHandler(); } + void SERCOM5_1_Handler() { Serial4.IrqHandler(); } + void SERCOM5_2_Handler() { Serial4.IrqHandler(); } + void SERCOM5_3_Handler() { Serial4.IrqHandler(); } +#endif + +#endif // ADAFRUIT_GRAND_CENTRAL_M4 diff --git a/Marlin/src/HAL/HAL_STM32F7/spi_pins.h b/Marlin/src/HAL/HAL_SAMD51/MarlinSerial_AGCM4.h similarity index 85% rename from Marlin/src/HAL/HAL_STM32F7/spi_pins.h rename to Marlin/src/HAL/HAL_SAMD51/MarlinSerial_AGCM4.h index 267cba6fd0..0768d8a04e 100644 --- a/Marlin/src/HAL/HAL_STM32F7/spi_pins.h +++ b/Marlin/src/HAL/HAL_SAMD51/MarlinSerial_AGCM4.h @@ -1,6 +1,8 @@ /** * Marlin 3D Printer Firmware + * * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * SAMD51 HAL developed by Giuliano Zaro (AKA GMagician) * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -18,10 +20,6 @@ */ #pragma once -/** - * Define SPI Pins: SCK, MISO, MOSI, SS - */ -#define SCK_PIN PA5 -#define MISO_PIN PA6 -#define MOSI_PIN PA7 -#define SS_PIN PA8 +extern Uart Serial2; +extern Uart Serial3; +extern Uart Serial4; diff --git a/Marlin/src/HAL/HAL_SAMD51/SAMD51.h b/Marlin/src/HAL/HAL_SAMD51/SAMD51.h new file mode 100644 index 0000000000..d29d134c00 --- /dev/null +++ b/Marlin/src/HAL/HAL_SAMD51/SAMD51.h @@ -0,0 +1,70 @@ +/** + * Marlin 3D Printer Firmware + * + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * SAMD51 HAL developed by Giuliano Zaro (AKA GMagician) + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +#define SYNC(sc) while (sc) { \ + asm(""); \ + } + +// Get SAMD port/pin from specified arduino pin +#define GET_SAMD_PORT(P) _GET_SAMD_PORT(PIN_TO_SAMD_PIN(P)) +#define GET_SAMD_PIN(P) _GET_SAMD_PIN(PIN_TO_SAMD_PIN(P)) + +// Get external interrupt line associated to specified arduino pin +#define PIN_TO_EILINE(P) _SAMDPORTPIN_TO_EILINE(GET_SAMD_PORT(P), GET_SAMD_PIN(P)) + +// Get adc/ain associated to specified arduino pin +#define PIN_TO_ADC(P) (ANAPIN_TO_ADCAIN(P) >> 8) +#define PIN_TO_AIN(P) (ANAPIN_TO_ADCAIN(P) & 0xFF) + +// Private defines +#define PIN_TO_SAMD_PIN(P) DIO##P##_PIN + +#define _GET_SAMD_PORT(P) ((P) >> 5) +#define _GET_SAMD_PIN(P) ((P) & 0x1F) + +// Get external interrupt line +#define _SAMDPORTPIN_TO_EILINE(P,B) ((P == 0 && WITHIN(B, 0, 31) && B != 8 && B != 26 && B != 28 && B != 29) ? (B) & 0xF \ + : (P == 1 && (WITHIN(B, 0, 25) || WITHIN(B, 30, 31))) ? (B) & 0xF \ + : (P == 1 && WITHIN(B, 26, 29)) ? 12 + (B) - 26 \ + : (P == 2 && (WITHIN(B, 0, 6) || WITHIN(B, 10, 31)) && B != 29) ? (B) & 0xF \ + : (P == 2 && B == 7) ? 9 \ + : (P == 3 && WITHIN(B, 0, 1)) ? (B) \ + : (P == 3 && WITHIN(B, 8, 12)) ? 3 + (B) - 8 \ + : (P == 3 && WITHIN(B, 20, 21)) ? 10 + (B) - 20 \ + : -1) + +// Get adc/ain +#define ANAPIN_TO_ADCAIN(P) _PIN_TO_ADCAIN(ANAPIN_TO_SAMDPIN(P)) +#define _PIN_TO_ADCAIN(P) _SAMDPORTPIN_TO_ADCAIN(_GET_SAMD_PORT(P), _GET_SAMD_PIN(P)) + +#define _SAMDPORTPIN_TO_ADCAIN(P,B) ((P == 0 && WITHIN(B, 2, 3)) ? 0x000 + (B) - 2 \ + : (P == 0 && WITHIN(B, 4, 7)) ? 0x000 + (B) \ + : (P == 0 && WITHIN(B, 8, 9)) ? 0x100 + 2 + (B) - 8 \ + : (P == 0 && WITHIN(B, 10, 11)) ? 0x000 + (B) \ + : (P == 1 && WITHIN(B, 0, 3)) ? 0x000 + 12 + (B) \ + : (P == 1 && WITHIN(B, 4, 7)) ? 0x100 + 6 + (B) - 4 \ + : (P == 1 && WITHIN(B, 8, 9)) ? 0x100 + (B) - 8 \ + : (P == 2 && WITHIN(B, 0, 1)) ? 0x100 + 10 + (B) \ + : (P == 2 && WITHIN(B, 2, 3)) ? 0x100 + 4 + (B) - 2 \ + : (P == 2 && WITHIN(B, 30, 31)) ? 0x100 + 12 + (B) - 30 \ + : (P == 3 && WITHIN(B, 0, 1)) ? 0x100 + 14 + (B) \ + : -1) diff --git a/Marlin/src/HAL/HAL_SAMD51/ServoTimers.h b/Marlin/src/HAL/HAL_SAMD51/ServoTimers.h new file mode 100644 index 0000000000..b1e18729c6 --- /dev/null +++ b/Marlin/src/HAL/HAL_SAMD51/ServoTimers.h @@ -0,0 +1,39 @@ +/** + * Marlin 3D Printer Firmware + * + * Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * SAMD51 HAL developed by Giuliano Zaro (AKA GMagician) + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +#define _useTimer1 +#define _useTimer2 + +#define TRIM_DURATION 5 // compensation ticks to trim adjust for digitalWrite delays +#define SERVO_TIMER_PRESCALER 64 // timer prescaler factor to 64 (avoid overflowing 16-bit clock counter, at 120MHz this is 1831 ticks per millisecond + +#define SERVO_TC 3 + +typedef enum { + #ifdef _useTimer1 + _timer1, + #endif + #ifdef _useTimer2 + _timer2, + #endif + _Nbr_16timers +} timer16_Sequence_t; diff --git a/Marlin/src/HAL/HAL_SAMD51/Servo_SAMD51.cpp b/Marlin/src/HAL/HAL_SAMD51/Servo_SAMD51.cpp new file mode 100644 index 0000000000..1e3c4f0161 --- /dev/null +++ b/Marlin/src/HAL/HAL_SAMD51/Servo_SAMD51.cpp @@ -0,0 +1,226 @@ +/** + * Marlin 3D Printer Firmware + * + * Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * SAMD51 HAL developed by Giuliano Zaro (AKA GMagician) + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + +/** + * This comes from Arduino library which at the moment is buggy and uncompilable + */ + +#ifdef __SAMD51__ + +#include "../../inc/MarlinConfig.h" + +#if HAS_SERVOS + +#include "../shared/Marduino.h" +#include "../shared/servo.h" +#include "../shared/servo_private.h" +#include "SAMD51.h" +#include "HAL_timers_SAMD51.h" + +#define __TC_GCLK_ID(t) TC##t##_GCLK_ID +#define _TC_GCLK_ID(t) __TC_GCLK_ID(t) +#define TC_GCLK_ID _TC_GCLK_ID(SERVO_TC) + +#define _TC_PRESCALER(d) TC_CTRLA_PRESCALER_DIV##d##_Val +#define TC_PRESCALER(d) _TC_PRESCALER(d) + +#define __SERVO_IRQn(t) TC##t##_IRQn +#define _SERVO_IRQn(t) __SERVO_IRQn(t) +#define SERVO_IRQn _SERVO_IRQn(SERVO_TC) + +#define HAL_SERVO_TIMER_ISR() TC_HANDLER(SERVO_TC) + +#define TIMER_TCCHANNEL(t) ((t) & 1) +#define TC_COUNTER_START_VAL 0xFFFF + + +static volatile int8_t currentServoIndex[_Nbr_16timers]; // index for the servo being pulsed for each timer (or -1 if refresh interval) + +FORCE_INLINE static uint16_t getTimerCount() { + Tc * const tc = TimerConfig[SERVO_TC].pTimer; + + tc->COUNT16.CTRLBSET.reg = TC_CTRLBCLR_CMD_READSYNC; + SYNC(tc->COUNT16.SYNCBUSY.bit.CTRLB || tc->COUNT16.SYNCBUSY.bit.COUNT); + + return tc->COUNT16.COUNT.reg; +} + +// ---------------------------- +// Interrupt handler for the TC +// ---------------------------- +HAL_SERVO_TIMER_ISR() { + Tc * const tc = TimerConfig[SERVO_TC].pTimer; + const timer16_Sequence_t timer = + #ifndef _useTimer1 + _timer2 + #elif !defined(_useTimer2) + _timer1 + #else + (tc->COUNT16.INTFLAG.reg & tc->COUNT16.INTENSET.reg & TC_INTFLAG_MC0) ? _timer1 : _timer2 + #endif + ; + const uint8_t tcChannel = TIMER_TCCHANNEL(timer); + + if (currentServoIndex[timer] < 0) { + #if defined(_useTimer1) && defined(_useTimer2) + if (currentServoIndex[timer ^ 1] >= 0) { + // Wait for both channels + // Clear the interrupt + tc->COUNT16.INTFLAG.reg = (tcChannel == 0) ? TC_INTFLAG_MC0 : TC_INTFLAG_MC1; + return; + } + #endif + tc->COUNT16.COUNT.reg = TC_COUNTER_START_VAL; + SYNC(tc->COUNT16.SYNCBUSY.bit.COUNT); + } + else if (SERVO_INDEX(timer, currentServoIndex[timer]) < ServoCount && SERVO(timer, currentServoIndex[timer]).Pin.isActive) + digitalWrite(SERVO(timer, currentServoIndex[timer]).Pin.nbr, LOW); // pulse this channel low if activated + + // Select the next servo controlled by this timer + currentServoIndex[timer]++; + + if (SERVO_INDEX(timer, currentServoIndex[timer]) < ServoCount && currentServoIndex[timer] < SERVOS_PER_TIMER) { + if (SERVO(timer, currentServoIndex[timer]).Pin.isActive) // check if activated + digitalWrite(SERVO(timer, currentServoIndex[timer]).Pin.nbr, HIGH); // it's an active channel so pulse it high + + tc->COUNT16.CC[tcChannel].reg = getTimerCount() - (uint16_t)SERVO(timer, currentServoIndex[timer]).ticks; + } + else { + // finished all channels so wait for the refresh period to expire before starting over + currentServoIndex[timer] = -1; // this will get incremented at the end of the refresh period to start again at the first channel + + const uint16_t tcCounterValue = getTimerCount(); + + if ((TC_COUNTER_START_VAL - tcCounterValue) + 4UL < usToTicks(REFRESH_INTERVAL)) // allow a few ticks to ensure the next OCR1A not missed + tc->COUNT16.CC[tcChannel].reg = TC_COUNTER_START_VAL - (uint16_t)usToTicks(REFRESH_INTERVAL); + else + tc->COUNT16.CC[tcChannel].reg = (uint16_t)(tcCounterValue - 4UL); // at least REFRESH_INTERVAL has elapsed + } + if (tcChannel == 0) { + SYNC(tc->COUNT16.SYNCBUSY.bit.CC0); + // Clear the interrupt + tc->COUNT16.INTFLAG.reg = TC_INTFLAG_MC0; + } + else { + SYNC(tc->COUNT16.SYNCBUSY.bit.CC1); + // Clear the interrupt + tc->COUNT16.INTFLAG.reg = TC_INTFLAG_MC1; + } +} + +void initISR(timer16_Sequence_t timer) { + Tc * const tc = TimerConfig[SERVO_TC].pTimer; + const uint8_t tcChannel = TIMER_TCCHANNEL(timer); + + static bool initialized = false; // Servo TC has been initialized + if (!initialized) { + NVIC_DisableIRQ(SERVO_IRQn); + + // Disable the timer + tc->COUNT16.CTRLA.bit.ENABLE = false; + SYNC(tc->COUNT16.SYNCBUSY.bit.ENABLE); + + // Select GCLK0 as timer/counter input clock source + GCLK->PCHCTRL[TC_GCLK_ID].bit.CHEN = false; + SYNC(GCLK->PCHCTRL[TC_GCLK_ID].bit.CHEN); + GCLK->PCHCTRL[TC_GCLK_ID].reg = GCLK_PCHCTRL_GEN_GCLK0 | GCLK_PCHCTRL_CHEN; // 120MHz startup code programmed + SYNC(!GCLK->PCHCTRL[TC_GCLK_ID].bit.CHEN); + + // Reset the timer + tc->COUNT16.CTRLA.bit.SWRST = true; + SYNC(tc->COUNT16.SYNCBUSY.bit.SWRST); + SYNC(tc->COUNT16.CTRLA.bit.SWRST); + + // Set timer counter mode to 16 bits + tc->COUNT16.CTRLA.reg = TC_CTRLA_MODE_COUNT16; + + // Set timer counter mode as normal PWM + tc->COUNT16.WAVE.bit.WAVEGEN = TCC_WAVE_WAVEGEN_NPWM_Val; + + // Set the prescaler factor + tc->COUNT16.CTRLA.bit.PRESCALER = TC_PRESCALER(SERVO_TIMER_PRESCALER); + + // Count down + tc->COUNT16.CTRLBSET.reg = TC_CTRLBCLR_DIR; + SYNC(tc->COUNT16.SYNCBUSY.bit.CTRLB); + + // Reset all servo indexes + memset(currentServoIndex, 0xFF, sizeof(currentServoIndex)); + + // Configure interrupt request + NVIC_ClearPendingIRQ(SERVO_IRQn); + NVIC_SetPriority(SERVO_IRQn, 5); + NVIC_EnableIRQ(SERVO_IRQn); + + initialized = true; + } + + if (!tc->COUNT16.CTRLA.bit.ENABLE) { + // Reset the timer counter + tc->COUNT16.COUNT.reg = TC_COUNTER_START_VAL; + SYNC(tc->COUNT16.SYNCBUSY.bit.COUNT); + + // Enable the timer and start it + tc->COUNT16.CTRLA.bit.ENABLE = true; + SYNC(tc->COUNT16.SYNCBUSY.bit.ENABLE); + } + // First interrupt request after 1 ms + tc->COUNT16.CC[tcChannel].reg = getTimerCount() - (uint16_t)usToTicks(1000UL); + + if (tcChannel == 0 ) { + SYNC(tc->COUNT16.SYNCBUSY.bit.CC0); + + // Clear pending match interrupt + tc->COUNT16.INTFLAG.reg = TC_INTENSET_MC0; + // Enable the match channel interrupt request + tc->COUNT16.INTENSET.reg = TC_INTENSET_MC0; + } + else { + SYNC(tc->COUNT16.SYNCBUSY.bit.CC1); + + // Clear pending match interrupt + tc->COUNT16.INTFLAG.reg = TC_INTENSET_MC1; + // Enable the match channel interrupt request + tc->COUNT16.INTENSET.reg = TC_INTENSET_MC1; + } +} + +void finISR(timer16_Sequence_t timer) { + Tc * const tc = TimerConfig[SERVO_TC].pTimer; + const uint8_t tcChannel = TIMER_TCCHANNEL(timer); + + // Disable the match channel interrupt request + tc->COUNT16.INTENCLR.reg = (tcChannel == 0) ? TC_INTENCLR_MC0 : TC_INTENCLR_MC1; + + if (true + #if defined(_useTimer1) && defined(_useTimer2) + && (tc->COUNT16.INTENCLR.reg & (TC_INTENCLR_MC0|TC_INTENCLR_MC1)) == 0 + #endif + ) { + // Disable the timer if not used + tc->COUNT16.CTRLA.bit.ENABLE = false; + SYNC(tc->COUNT16.SYNCBUSY.bit.ENABLE); + } +} + +#endif // HAS_SERVOS + +#endif // __SAMD51__ diff --git a/Marlin/src/HAL/HAL_SAMD51/endstop_interrupts.h b/Marlin/src/HAL/HAL_SAMD51/endstop_interrupts.h new file mode 100644 index 0000000000..26c11b6e8b --- /dev/null +++ b/Marlin/src/HAL/HAL_SAMD51/endstop_interrupts.h @@ -0,0 +1,184 @@ +/** + * Marlin 3D Printer Firmware + * + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * SAMD51 HAL developed by Giuliano Zaro (AKA GMagician) + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Endstop interrupts for ATMEL SAMD51 based targets. + * + * On SAMD51, all pins support external interrupt capability. + * Any pin can be used for external interrupts, but there are some restrictions. + * At most 16 different external interrupts can be used at one time. + * Further, you can’t just pick any 16 pins to use. This is because every pin on the SAMD51 + * connects to what is called an EXTINT line, and only one pin per EXTINT line can be used for external + * interrupts at a time + */ + +/** + * Endstop Interrupts + * + * Without endstop interrupts the endstop pins must be polled continually in + * the temperature-ISR via endstops.update(), most of the time finding no change. + * With this feature endstops.update() is called only when we know that at + * least one endstop has changed state, saving valuable CPU cycles. + * + * This feature only works when all used endstop pins can generate an 'external interrupt'. + * + * Test whether pins issue interrupts on your board by flashing 'pin_interrupt_test.ino'. + * (Located in Marlin/buildroot/share/pin_interrupt_test/pin_interrupt_test.ino) + */ + +#include "../../module/endstops.h" + +#define MATCH_EILINE(P1,P2) (P1 != P2 && PIN_TO_EILINE(P1) == PIN_TO_EILINE(P2)) +#if HAS_X_MAX + #define MATCH_X_MAX_EILINE(P) MATCH_EILINE(P, X_MAX_PIN) +#else + #define MATCH_X_MAX_EILINE(P) false +#endif +#if HAS_X_MIN + #define MATCH_X_MIN_EILINE(P) MATCH_EILINE(P, X_MIN_PIN) +#else + #define MATCH_X_MIN_EILINE(P) false +#endif +#if HAS_Y_MAX + #define MATCH_Y_MAX_EILINE(P) MATCH_EILINE(P, Y_MAX_PIN) +#else + #define MATCH_Y_MAX_EILINE(P) false +#endif +#if HAS_Y_MIN + #define MATCH_Y_MIN_EILINE(P) MATCH_EILINE(P, Y_MIN_PIN) +#else + #define MATCH_Y_MIN_EILINE(P) false +#endif +#if HAS_Z_MAX + #define MATCH_Z_MAX_EILINE(P) MATCH_EILINE(P, Z_MAX_PIN) +#else + #define MATCH_Z_MAX_EILINE(P) false +#endif +#if HAS_Z_MIN + #define MATCH_Z_MIN_EILINE(P) MATCH_EILINE(P, Z_MIN_PIN) +#else + #define MATCH_Z_MIN_EILINE(P) false +#endif +#if HAS_Z2_MAX + #define MATCH_Z2_MAX_EILINE(P) MATCH_EILINE(P, Z2_MAX_PIN) +#else + #define MATCH_Z2_MAX_EILINE(P) false +#endif +#if HAS_Z2_MIN + #define MATCH_Z2_MIN_EILINE(P) MATCH_EILINE(P, Z2_MIN_PIN) +#else + #define MATCH_Z2_MIN_EILINE(P) false +#endif +#if HAS_Z3_MAX + #define MATCH_Z3_MAX_EILINE(P) MATCH_EILINE(P, Z3_MAX_PIN) +#else + #define MATCH_Z3_MAX_EILINE(P) false +#endif +#if HAS_Z3_MIN + #define MATCH_Z3_MIN_EILINE(P) MATCH_EILINE(P, Z3_MIN_PIN) +#else + #define MATCH_Z3_MIN_EILINE(P) false +#endif +#if HAS_Z_MIN_PROBE_PIN + #define MATCH_Z_MIN_PROBE_EILINE(P) MATCH_EILINE(P, Z_MIN_PROBE_PIN) +#else + #define MATCH_Z_MIN_PROBE_EILINE(P) false +#endif +#define AVAILABLE_EILINE(P) (PIN_TO_EILINE(P) != -1 \ + && !MATCH_X_MAX_EILINE(P) && !MATCH_X_MIN_EILINE(P) \ + && !MATCH_Y_MAX_EILINE(P) && !MATCH_Y_MIN_EILINE(P) \ + && !MATCH_Z_MAX_EILINE(P) && !MATCH_Z_MIN_EILINE(P) \ + && !MATCH_Z2_MAX_EILINE(P) && !MATCH_Z2_MIN_EILINE(P) \ + && !MATCH_Z3_MAX_EILINE(P) && !MATCH_Z3_MIN_EILINE(P) \ + && !MATCH_Z_MIN_PROBE_EILINE(P)) + +// One ISR for all EXT-Interrupts +void endstop_ISR(void) { endstops.update(); } + +void setup_endstop_interrupts(void) { + #if HAS_X_MAX + #if !AVAILABLE_EILINE(X_MAX_PIN) + static_assert(false, "X_MAX_PIN has no EXTINT line available."); + #endif + attachInterrupt(X_MAX_PIN, endstop_ISR, CHANGE); + #endif + #if HAS_X_MIN + #if !AVAILABLE_EILINE(X_MIN_PIN) + static_assert(false, "X_MIN_PIN has no EXTINT line available."); + #endif + attachInterrupt(X_MIN_PIN, endstop_ISR, CHANGE); + #endif + #if HAS_Y_MAX + #if !AVAILABLE_EILINE(Y_MAX_PIN) + static_assert(false, "Y_MAX_PIN has no EXTINT line available."); + #endif + attachInterrupt(Y_MAX_PIN, endstop_ISR, CHANGE); + #endif + #if HAS_Y_MIN + #if !AVAILABLE_EILINE(Y_MIN_PIN) + static_assert(false, "Y_MIN_PIN has no EXTINT line available."); + #endif + attachInterrupt(Y_MIN_PIN, endstop_ISR, CHANGE); + #endif + #if HAS_Z_MAX + #if !AVAILABLE_EILINE(Z_MAX_PIN) + static_assert(false, "Z_MAX_PIN has no EXTINT line available."); + #endif + attachInterrupt(Z_MAX_PIN, endstop_ISR, CHANGE); + #endif + #if HAS_Z_MIN + #if !AVAILABLE_EILINE(Z_MIN_PIN) + static_assert(false, "Z_MIN_PIN has no EXTINT line available."); + #endif + attachInterrupt(Z_MIN_PIN, endstop_ISR, CHANGE); + #endif + #if HAS_Z2_MAX + #if !AVAILABLE_EILINE(Z2_MAX_PIN) + static_assert(false, "Z2_MAX_PIN has no EXTINT line available."); + #endif + attachInterrupt(Z2_MAX_PIN, endstop_ISR, CHANGE); + #endif + #if HAS_Z2_MIN + #if !AVAILABLE_EILINE(Z2_MIN_PIN) + static_assert(false, "Z2_MIN_PIN has no EXTINT line available."); + #endif + attachInterrupt(Z2_MIN_PIN, endstop_ISR, CHANGE); + #endif + #if HAS_Z3_MAX + #if !AVAILABLE_EILINE(Z3_MAX_PIN) + static_assert(false, "Z3_MAX_PIN has no EXTINT line available."); + #endif + attachInterrupt(Z3_MAX_PIN, endstop_ISR, CHANGE); + #endif + #if HAS_Z3_MIN + #if !AVAILABLE_EILINE(Z3_MIN_PIN) + static_assert(false, "Z3_MIN_PIN has no EXTINT line available."); + #endif + attachInterrupt(Z3_MIN_PIN, endstop_ISR, CHANGE); + #endif + #if HAS_Z_MIN_PROBE_PIN + #if !AVAILABLE_EILINE(Z_MIN_PROBE_PIN) + static_assert(false, "Z_MIN_PROBE_PIN has no EXTINT line available."); + #endif + attachInterrupt(Z_MIN_PROBE_PIN, endstop_ISR, CHANGE); + #endif +} diff --git a/Marlin/src/HAL/HAL_SAMD51/fastio_SAMD51.h b/Marlin/src/HAL/HAL_SAMD51/fastio_SAMD51.h new file mode 100644 index 0000000000..93136911f6 --- /dev/null +++ b/Marlin/src/HAL/HAL_SAMD51/fastio_SAMD51.h @@ -0,0 +1,251 @@ +/** + * Marlin 3D Printer Firmware + * + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * SAMD51 HAL developed by Giuliano Zaro (AKA GMagician) + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Fast IO functions for SAMD51 + */ + +#include "SAMD51.h" + +/** + * Utility functions + */ + +#ifndef MASK + #define MASK(PIN) (1 << PIN) +#endif + +/** + * Magic I/O routines + * + * Now you can simply SET_OUTPUT(STEP); WRITE(STEP, HIGH); WRITE(STEP, LOW); + */ + +// Read a pin +#define READ(IO) ((PORT->Group[(EPortType)GET_SAMD_PORT(IO)].IN.reg & MASK(GET_SAMD_PIN(IO))) != 0) + +// Write to a pin +#define WRITE(IO,V) do{ \ + const EPortType port = (EPortType)GET_SAMD_PORT(IO); \ + const uint32_t mask = MASK(GET_SAMD_PIN(IO)); \ + \ + if (V) PORT->Group[port].OUTSET.reg = mask; \ + else PORT->Group[port].OUTCLR.reg = mask; \ + }while(0) + +// Toggle a pin +#define TOGGLE(IO) PORT->Group[(EPortType)GET_SAMD_PORT(IO)].OUTTGL.reg = MASK(GET_SAMD_PIN(IO)); + +// Set pin as input +#define SET_INPUT(IO) do{ \ + const EPortType port = (EPortType)GET_SAMD_PORT(IO); \ + const uint32_t pin = GET_SAMD_PIN(IO); \ + \ + PORT->Group[port].PINCFG[pin].reg = (uint8_t)(PORT_PINCFG_INEN); \ + PORT->Group[port].DIRCLR.reg = MASK(pin); \ + }while(0) +// Set pin as input with pullup +#define SET_INPUT_PULLUP(IO) do{ \ + const EPortType port = (EPortType)GET_SAMD_PORT(IO); \ + const uint32_t pin = GET_SAMD_PIN(IO); \ + const uint32_t mask = MASK(pin); \ + \ + PORT->Group[port].PINCFG[pin].reg = (uint8_t)(PORT_PINCFG_INEN | PORT_PINCFG_PULLEN); \ + PORT->Group[port].DIRCLR.reg = mask; \ + PORT->Group[port].OUTSET.reg = mask; \ + }while(0) +// Set pin as input with pulldown +#define SET_INPUT_PULLDOWN(IO) do{ \ + const EPortType port = (EPortType)GET_SAMD_PORT(IO); \ + const uint32_t pin = GET_SAMD_PIN(IO); \ + const uint32_t mask = MASK(pin); \ + \ + PORT->Group[port].PINCFG[pin].reg = (uint8_t)(PORT_PINCFG_INEN | PORT_PINCFG_PULLEN); \ + PORT->Group[port].DIRCLR.reg = mask; \ + PORT->Group[port].OUTCLR.reg = mask; \ + }while(0) +// Set pin as output (push pull) +#define SET_OUTPUT(IO) do{ \ + const EPortType port = (EPortType)GET_SAMD_PORT(IO); \ + const uint32_t pin = GET_SAMD_PIN(IO); \ + \ + PORT->Group[port].PINCFG[pin].reg = (uint8_t)(PORT_PINCFG_INEN); \ + PORT->Group[port].DIRSET.reg = MASK(pin); \ + }while(0) +// Set pin as output (open drain) +#define SET_OUTPUT_OD(IO) do{ \ + const EPortType port = (EPortType)GET_SAMD_PORT(IO); \ + const uint32_t pin = GET_SAMD_PIN(IO); \ + \ + PORT->Group[port].PINCFG[pin].reg = (uint8_t)(PORT_PINCFG_PULLEN); \ + PORT->Group[port].DIRCLR.reg = MASK(pin); \ + }while(0) +// Set pin as PWM (push pull) +#define SET_PWM(IO) SET_OUTPUT(IO) +// Set pin as PWM (open drain) +#define SET_PWM_OD(IO) SET_OUTPUT_OD(IO) + +// check if pin is an output +#define IS_OUTPUT(IO) ((PORT->Group[(EPortType)GET_SAMD_PORT(IO)].DIR.reg & MASK(GET_SAMD_PIN(IO))) \ + || (PORT->Group[(EPortType)GET_SAMD_PORT(IO)].PINCFG[GET_SAMD_PIN(IO)].reg & (PORT_PINCFG_INEN | PORT_PINCFG_PULLEN)) == PORT_PINCFG_PULLEN) +// check if pin is an input +#define IS_INPUT(IO) !IS_OUTPUT(IO) + +// Shorthand +#define OUT_WRITE(IO,V) do{ SET_OUTPUT(IO); WRITE(IO,V); }while(0) +#define OUT_WRITE_OD(IO,V) do{ SET_OUTPUT_OD(IO); WRITE(IO,V); }while(0) + +// digitalRead/Write wrappers +#define extDigitalRead(IO) digitalRead(IO) +#define extDigitalWrite(IO,V) digitalWrite(IO,V) + +/** + * Ports and functions + * Added as necessary or if I feel like it- not a comprehensive list! + */ + +#ifdef ADAFRUIT_GRAND_CENTRAL_M4 + + /* + * Adafruit Grand Central M4 has a lot of PWMs the availables are listed here. + * Some of these share the same source and so can't be used in the same time + */ + #define PWM_PIN(P) (WITHIN(P, 2, 13) || WITHIN(P, 22, 23) || WITHIN(P, 44, 45) || P == 48) + + // Return fullfilled ADCx->INPUTCTRL.reg + #define PIN_TO_INPUTCTRL(P) ( (PIN_TO_AIN(P) == 0) ? ADC_INPUTCTRL_MUXPOS_AIN0 \ + : (PIN_TO_AIN(P) == 1) ? ADC_INPUTCTRL_MUXPOS_AIN1 \ + : (PIN_TO_AIN(P) == 2) ? ADC_INPUTCTRL_MUXPOS_AIN2 \ + : (PIN_TO_AIN(P) == 3) ? ADC_INPUTCTRL_MUXPOS_AIN3 \ + : (PIN_TO_AIN(P) == 4) ? ADC_INPUTCTRL_MUXPOS_AIN4 \ + : (PIN_TO_AIN(P) == 5) ? ADC_INPUTCTRL_MUXPOS_AIN5 \ + : (PIN_TO_AIN(P) == 6) ? ADC_INPUTCTRL_MUXPOS_AIN6 \ + : (PIN_TO_AIN(P) == 7) ? ADC_INPUTCTRL_MUXPOS_AIN7 \ + : (PIN_TO_AIN(P) == 8) ? ADC_INPUTCTRL_MUXPOS_AIN8 \ + : (PIN_TO_AIN(P) == 9) ? ADC_INPUTCTRL_MUXPOS_AIN9 \ + : (PIN_TO_AIN(P) == 10) ? ADC_INPUTCTRL_MUXPOS_AIN10 \ + : (PIN_TO_AIN(P) == 11) ? ADC_INPUTCTRL_MUXPOS_AIN11 \ + : (PIN_TO_AIN(P) == 12) ? ADC_INPUTCTRL_MUXPOS_AIN12 \ + : (PIN_TO_AIN(P) == 13) ? ADC_INPUTCTRL_MUXPOS_AIN13 \ + : (PIN_TO_AIN(P) == 14) ? ADC_INPUTCTRL_MUXPOS_AIN14 \ + : ADC_INPUTCTRL_MUXPOS_AIN15) + + #define ANAPIN_TO_SAMDPIN(P) ( (P == 0) ? PIN_TO_SAMD_PIN(67) \ + : (P == 1) ? PIN_TO_SAMD_PIN(68) \ + : (P == 2) ? PIN_TO_SAMD_PIN(69) \ + : (P == 3) ? PIN_TO_SAMD_PIN(70) \ + : (P == 4) ? PIN_TO_SAMD_PIN(71) \ + : (P == 5) ? PIN_TO_SAMD_PIN(72) \ + : (P == 6) ? PIN_TO_SAMD_PIN(73) \ + : (P == 7) ? PIN_TO_SAMD_PIN(74) \ + : (P == 8) ? PIN_TO_SAMD_PIN(54) \ + : (P == 9) ? PIN_TO_SAMD_PIN(55) \ + : (P == 10) ? PIN_TO_SAMD_PIN(56) \ + : (P == 11) ? PIN_TO_SAMD_PIN(57) \ + : (P == 12) ? PIN_TO_SAMD_PIN(58) \ + : (P == 13) ? PIN_TO_SAMD_PIN(59) \ + : (P == 14) ? PIN_TO_SAMD_PIN(60) \ + : (P == 15) ? PIN_TO_SAMD_PIN(61) \ + : (P == 16) ? PIN_TO_SAMD_PIN(12) \ + : (P == 17) ? PIN_TO_SAMD_PIN(13) \ + : PIN_TO_SAMD_PIN(9)) + + #define digitalPinToAnalogInput(P) (WITHIN(P, 67, 74) ? (P) - 67 : WITHIN(P, 54, 61) ? 8 + (P) - 54 : WITHIN(P, 12, 13) ? 16 + (P) - 12 : P == 9 ? 18 : -1) + + /* + * pins + */ + + // PORTA + #define DIO67_PIN PIN_PA02 // A0 + #define DIO59_PIN PIN_PA04 // A13 + #define DIO68_PIN PIN_PA05 // A1 + #define DIO60_PIN PIN_PA06 // A14 + #define DIO61_PIN PIN_PA07 // A15 + #define DIO26_PIN PIN_PA12 + #define DIO27_PIN PIN_PA13 + #define DIO28_PIN PIN_PA14 + #define DIO23_PIN PIN_PA15 + #define DIO37_PIN PIN_PA16 + #define DIO36_PIN PIN_PA17 + #define DIO35_PIN PIN_PA18 + #define DIO34_PIN PIN_PA19 + #define DIO33_PIN PIN_PA20 + #define DIO32_PIN PIN_PA21 + #define DIO31_PIN PIN_PA22 + #define DIO30_PIN PIN_PA23 + // PORTB + #define DIO12_PIN PIN_PB00 // A16 + #define DIO13_PIN PIN_PB01 // A17 + #define DIO9_PIN PIN_PB02 // A18 + #define DIO69_PIN PIN_PB03 // A2 + #define DIO74_PIN PIN_PB04 // A7 + #define DIO54_PIN PIN_PB05 // A8 + #define DIO55_PIN PIN_PB06 // A9 + #define DIO56_PIN PIN_PB07 // A10 + #define DIO57_PIN PIN_PB08 // A11 + #define DIO58_PIN PIN_PB09 // A12 + #define DIO18_PIN PIN_PB12 + #define DIO19_PIN PIN_PB13 + #define DIO39_PIN PIN_PB14 + #define DIO38_PIN PIN_PB15 + #define DIO14_PIN PIN_PB16 + #define DIO15_PIN PIN_PB17 + #define DIO8_PIN PIN_PB18 + #define DIO29_PIN PIN_PB19 + #define DIO20_PIN PIN_PB20 + #define DIO21_PIN PIN_PB21 + #define DIO10_PIN PIN_PB22 + #define DIO11_PIN PIN_PB23 + #define DIO1_PIN PIN_PB24 + #define DIO0_PIN PIN_PB25 + #define DIO83_PIN PIN_PB28 // SD_CS + #define DIO95_PIN PIN_PB31 // SD_CD + // PORTC + #define DIO70_PIN PIN_PC00 // A3 + #define DIO71_PIN PIN_PC01 // A4 + #define DIO72_PIN PIN_PC02 // A5 + #define DIO73_PIN PIN_PC03 // A6 + #define DIO48_PIN PIN_PC04 + #define DIO49_PIN PIN_PC05 + #define DIO46_PIN PIN_PC06 + #define DIO47_PIN PIN_PC07 + #define DIO45_PIN PIN_PC10 + #define DIO44_PIN PIN_PC11 + #define DIO41_PIN PIN_PC12 + #define DIO40_PIN PIN_PC13 + #define DIO43_PIN PIN_PC14 + #define DIO42_PIN PIN_PC15 + #define DIO25_PIN PIN_PC16 + #define DIO24_PIN PIN_PC17 + #define DIO2_PIN PIN_PC18 + #define DIO3_PIN PIN_PC19 + #define DIO4_PIN PIN_PC20 + #define DIO5_PIN PIN_PC21 + #define DIO16_PIN PIN_PC22 + #define DIO17_PIN PIN_PC23 + // PORTD + #define DIO22_PIN PIN_PD12 + #define DIO6_PIN PIN_PD20 + #define DIO7_PIN PIN_PD21 + +#endif // ADAFRUIT_GRAND_CENTRAL_M4 diff --git a/Marlin/src/HAL/HAL_SAMD51/inc/Conditionals_LCD.h b/Marlin/src/HAL/HAL_SAMD51/inc/Conditionals_LCD.h new file mode 100644 index 0000000000..85f26f4016 --- /dev/null +++ b/Marlin/src/HAL/HAL_SAMD51/inc/Conditionals_LCD.h @@ -0,0 +1,22 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once diff --git a/Marlin/src/HAL/HAL_SAMD51/inc/Conditionals_adv.h b/Marlin/src/HAL/HAL_SAMD51/inc/Conditionals_adv.h new file mode 100644 index 0000000000..85f26f4016 --- /dev/null +++ b/Marlin/src/HAL/HAL_SAMD51/inc/Conditionals_adv.h @@ -0,0 +1,22 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once diff --git a/Marlin/src/HAL/HAL_SAMD51/inc/Conditionals_post.h b/Marlin/src/HAL/HAL_SAMD51/inc/Conditionals_post.h new file mode 100644 index 0000000000..85f26f4016 --- /dev/null +++ b/Marlin/src/HAL/HAL_SAMD51/inc/Conditionals_post.h @@ -0,0 +1,22 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once diff --git a/Marlin/src/HAL/HAL_SAMD51/inc/SanityCheck.h b/Marlin/src/HAL/HAL_SAMD51/inc/SanityCheck.h new file mode 100644 index 0000000000..0d45b28c32 --- /dev/null +++ b/Marlin/src/HAL/HAL_SAMD51/inc/SanityCheck.h @@ -0,0 +1,48 @@ +/** + * Marlin 3D Printer Firmware + * + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * SAMD51 HAL developed by Giuliano Zaro (AKA GMagician) + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + +/** + * Test SAMD51 specific configuration values for errors at compile-time. + */ + +#if defined(ADAFRUIT_GRAND_CENTRAL_M4) && SD_CONNECTION_IS(CUSTOM_CABLE) + #error "No custom SD drive cable defined for this board." +#endif + +#if defined(MAX6675_SCK_PIN) && defined(MAX6675_DO_PIN) && (MAX6675_SCK_PIN == SCK1 || MAX6675_DO_PIN == MISO1) + #error "OnBoard SPI BUS can't be shared with other devices." +#endif + +#if ENABLED(EMERGENCY_PARSER) + #error "EMERGENCY_PARSER is not yet implemented for STM32F4. Disable EMERGENCY_PARSER to continue." +#endif + +#if ENABLED(SDIO_SUPPORT) + #error "SDIO_SUPPORT is not supported." +#endif + +#if ENABLED(FAST_PWM_FAN) + #error "FAST_PWM_FAN is not yet implemented for this platform." +#endif + +#if ENABLED(EEPROM_SETTINGS) && NONE(SPI_EEPROM, I2C_EEPROM) + #warning "Did you activate the SmartEEPROM? See https://github.com/GMagician/SAMD51-SmartEEprom-Activator" +#endif diff --git a/Marlin/src/HAL/HAL_SAMD51/persistent_store_eeprom.cpp b/Marlin/src/HAL/HAL_SAMD51/persistent_store_eeprom.cpp new file mode 100644 index 0000000000..e41dd85c85 --- /dev/null +++ b/Marlin/src/HAL/HAL_SAMD51/persistent_store_eeprom.cpp @@ -0,0 +1,129 @@ +/** + * Marlin 3D Printer Firmware + * + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * SAMD51 HAL developed by Giuliano Zaro (AKA GMagician) + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + +#ifdef __SAMD51__ + +#include "../../inc/MarlinConfig.h" + +#if ENABLED(EEPROM_SETTINGS) + +#include "../shared/persistent_store_api.h" + +#if NONE(SPI_EEPROM, I2C_EEPROM) + #define NVMCTRL_CMD(c) do{ \ + SYNC(!NVMCTRL->STATUS.bit.READY); \ + NVMCTRL->INTFLAG.bit.DONE = true; \ + NVMCTRL->CTRLB.reg = c | NVMCTRL_CTRLB_CMDEX_KEY; \ + SYNC(NVMCTRL->INTFLAG.bit.DONE); \ + }while(0) + #define NVMCTRL_FLUSH() do{ \ + if (NVMCTRL->SEESTAT.bit.LOAD) \ + NVMCTRL_CMD(NVMCTRL_CTRLB_CMD_SEEFLUSH); \ + }while(0) +#endif + +bool PersistentStore::access_start() { + #if NONE(SPI_EEPROM, I2C_EEPROM) + NVMCTRL->SEECFG.reg = NVMCTRL_SEECFG_WMODE_BUFFERED; // Buffered mode and segment reallocation active + #endif + + return true; +} + +bool PersistentStore::access_finish() { + #if NONE(SPI_EEPROM, I2C_EEPROM) + NVMCTRL_FLUSH(); + if (!NVMCTRL->SEESTAT.bit.LOCK) + NVMCTRL_CMD(NVMCTRL_CTRLB_CMD_LSEE); // Lock E2P data write access + #endif + + return true; +} + +bool PersistentStore::write_data(int &pos, const uint8_t *value, size_t size, uint16_t *crc) { + #if NONE(SPI_EEPROM, I2C_EEPROM) + if (NVMCTRL->SEESTAT.bit.RLOCK) + NVMCTRL_CMD(NVMCTRL_CTRLB_CMD_USEE); // Unlock E2P data write access + #endif + + while (size--) { + const uint8_t v = *value; + #if ANY(SPI_EEPROM, I2C_EEPROM) + uint8_t * const p = (uint8_t * const)pos; + if (v != eeprom_read_byte(p)) { + eeprom_write_byte(p, v); + delay(2); + if (eeprom_read_byte(p) != v) { + SERIAL_ECHO_MSG(MSG_ERR_EEPROM_WRITE); + return true; + } + } + #else + SYNC(NVMCTRL->SEESTAT.bit.BUSY); + if (NVMCTRL->INTFLAG.bit.SEESFULL) + NVMCTRL_FLUSH(); // Next write will trigger a sector reallocation. I need to flush 'pagebuffer' + ((volatile uint8_t *)SEEPROM_ADDR)[pos] = v; + SYNC(!NVMCTRL->INTFLAG.bit.SEEWRC); + #endif + crc16(crc, &v, 1); + pos++; + value++; + } + return false; +} + +bool PersistentStore::read_data(int &pos, uint8_t* value, size_t size, uint16_t *crc, const bool writing/*=true*/) { + while (size--) { + uint8_t c; + #if ANY(SPI_EEPROM, I2C_EEPROM) + c = eeprom_read_byte((uint8_t*)pos); + #else + SYNC(NVMCTRL->SEESTAT.bit.BUSY); + c = ((volatile uint8_t *)SEEPROM_ADDR)[pos]; + #endif + if (writing) *value = c; + crc16(crc, &c, 1); + pos++; + value++; + } + return false; +} + +size_t PersistentStore::capacity() { + #if ANY(SPI_EEPROM, I2C_EEPROM) + return E2END + 1; + #else + const uint8_t psz = NVMCTRL->SEESTAT.bit.PSZ, + sblk = NVMCTRL->SEESTAT.bit.SBLK; + + if (!psz && !sblk) return 0; + else if (psz <= 2) return (0x200 << psz); + else if (sblk == 1 || psz == 3) return 4096; + else if (sblk == 2 || psz == 4) return 8192; + else if (sblk <= 4 || psz == 5) return 16384; + else if (sblk >= 9 && psz == 7) return 65536; + else return 32768; + #endif +} + +#endif // EEPROM_SETTINGS + +#endif // __SAMD51__ diff --git a/Marlin/src/HAL/HAL_SAMD51/pinsDebug.h b/Marlin/src/HAL/HAL_SAMD51/pinsDebug.h new file mode 100644 index 0000000000..64f6929c00 --- /dev/null +++ b/Marlin/src/HAL/HAL_SAMD51/pinsDebug.h @@ -0,0 +1,153 @@ +/** + * Marlin 3D Printer Firmware + * + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * SAMD51 HAL developed by Giuliano Zaro (AKA GMagician) + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +#define NUMBER_PINS_TOTAL PINS_COUNT + +#define digitalRead_mod(p) extDigitalRead(p) +#define PRINT_PORT(p) do{ SERIAL_ECHOPGM(" Port: "); sprintf_P(buffer, PSTR("%c%02ld"), 'A' + g_APinDescription[p].ulPort, g_APinDescription[p].ulPin); SERIAL_ECHO(buffer); }while (0) +#define PRINT_ARRAY_NAME(x) do{ sprintf_P(buffer, PSTR("%-" STRINGIFY(MAX_NAME_LENGTH) "s"), pin_array[x].name); SERIAL_ECHO(buffer); }while(0) +#define PRINT_PIN(p) do{ sprintf_P(buffer, PSTR("%3d "), p); SERIAL_ECHO(buffer); }while(0) +#define GET_ARRAY_PIN(p) pin_array[p].pin +#define GET_ARRAY_IS_DIGITAL(p) pin_array[p].is_digital +#define VALID_PIN(pin) (pin >= 0 && pin < (int8_t)NUMBER_PINS_TOTAL) +#define DIGITAL_PIN_TO_ANALOG_PIN(p) digitalPinToAnalogInput(p) +#define IS_ANALOG(P) (DIGITAL_PIN_TO_ANALOG_PIN(P)!=-1) +#define pwm_status(pin) digitalPinHasPWM(pin) +#define MULTI_NAME_PAD 27 // space needed to be pretty if not first name assigned to a pin + +// pins that will cause hang/reset/disconnect in M43 Toggle and Watch utilities +// uses pin index +#define M43_NEVER_TOUCH(Q) ((Q) >= 75) + +bool GET_PINMODE(int8_t pin) { // 1: output, 0: input + const EPortType samdport = g_APinDescription[pin].ulPort; + const uint32_t samdpin = g_APinDescription[pin].ulPin; + return PORT->Group[samdport].DIR.reg & MASK(samdpin) || (PORT->Group[samdport].PINCFG[samdpin].reg & (PORT_PINCFG_INEN | PORT_PINCFG_PULLEN)) == PORT_PINCFG_PULLEN; +} + +void pwm_details(int32_t pin) { + if (pwm_status(pin)) { + //uint32_t chan = g_APinDescription[pin].ulPWMChannel TODO when fast pwm is operative; + //SERIAL_ECHOPAIR("PWM = ", duty); + } +} + +/** + * AGCM4 Board pin | PORT | Label + * ----------------+--------+------- + * 0 | PB25 | "RX0" + * 1 | PB24 | "TX0" + * 2 | PC18 | + * 3 | PC19 | + * 4 | PC20 | + * 5 | PC21 | + * 6 | PD20 | + * 7 | PD21 | + * 8 | PB18 | + * 9 | PB2 | + * 10 | PB22 | + * 11 | PB23 | + * 12 | PB0 | "A16" + * 13 | PB1 | LED AMBER "L" / "A17" + * 14 | PB16 | "TX3" + * 15 | PB17 | "RX3" + * 16 | PC22 | "TX2" + * 17 | PC23 | "RX2" + * 18 | PB12 | "TX1" / "A18" + * 19 | PB13 | "RX1" + * 20 | PB20 | "SDA" + * 21 | PB21 | "SCL" + * 22 | PD12 | + * 23 | PA15 | + * 24 | PC17 | + * 25 | PC16 | + * 26 | PA12 | + * 27 | PA13 | + * 28 | PA14 | + * 29 | PB19 | + * 30 | PA23 | + * 31 | PA22 | + * 32 | PA21 | + * 33 | PA20 | + * 34 | PA19 | + * 35 | PA18 | + * 36 | PA17 | + * 37 | PA16 | + * 38 | PB15 | + * 39 | PB14 | + * 40 | PC13 | + * 41 | PC12 | + * 42 | PC15 | + * 43 | PC14 | + * 44 | PC11 | + * 45 | PC10 | + * 46 | PC6 | + * 47 | PC7 | + * 48 | PC4 | + * 49 | PC5 | + * 50 | PD11 | + * 51 | PD8 | + * 52 | PD9 | + * 53 | PD10 | + * 54 | PB5 | "A8" + * 55 | PB6 | "A9" + * 56 | PB7 | "A10" + * 57 | PB8 | "A11" + * 58 | PB9 | "A12" + * 69 | PA4 | "A13" + * 60 | PA6 | "A14" + * 61 | PA7 | "A15" + * 62 | PB17 | + * 63 | PB20 | + * 64 | PD11 | + * 65 | PD8 | + * 66 | PD9 | + * 67 | PA2 | "A0" / "DAC0" + * 68 | PA5 | "A1" / "DAC1" + * 69 | PB3 | "A2" + * 70 | PC0 | "A3" + * 71 | PC1 | "A4" + * 72 | PC2 | "A5" + * 73 | PC3 | "A6" + * 74 | PB4 | "A7" + * 75 | PC31 | LED GREEN "RX" + * 76 | PC30 | LED GREEN "TX" + * 77 | PA27 | USB: Host enable + * 78 | PA24 | USB: D- + * 79 | PA25 | USB: D+ + * 80 | PB29 | SD: MISO + * 81 | PB27 | SD: SCK + * 82 | PB26 | SD: MOSI + * 83 | PB28 | SD: CS + * 84 | PA3 | AREF + * 85 | PA2 | DAC0 (Duplicate) + * 86 | PA5 | DAC1 (Duplicate) + * 87 | PB1 | LED AMBER "L" (Duplicate) + * 88 | PC24 | NeoPixel + * 89 | PB10 | QSPI: SCK + * 90 | PB11 | QSPI: CS + * 91 | PA8 | QSPI: IO0 + * 92 | PA9 | QSPI: IO1 + * 93 | PA10 | QSPI: IO2 + * 94 | PA11 | QSPI: IO3 + * + */ diff --git a/Marlin/src/HAL/HAL_SAMD51/spi_pins.h b/Marlin/src/HAL/HAL_SAMD51/spi_pins.h new file mode 100644 index 0000000000..3315fa08ac --- /dev/null +++ b/Marlin/src/HAL/HAL_SAMD51/spi_pins.h @@ -0,0 +1,54 @@ +/** + * Marlin 3D Printer Firmware + * + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * SAMD51 HAL developed by Giuliano Zaro (AKA GMagician) + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +#ifdef ADAFRUIT_GRAND_CENTRAL_M4 + + /* + * AGCM4 Default SPI Pins + * + * SS SCK MISO MOSI + * +-------------------------+ + * SPI | 53 52 50 51 | + * SPI1 | 83 81 80 82 | + * +-------------------------+ + * Any pin can be used for Chip Select (SS_PIN) + */ + #ifndef SCK_PIN + #define SCK_PIN 52 + #endif + #ifndef MISO_PIN + #define MISO_PIN 50 + #endif + #ifndef MOSI_PIN + #define MOSI_PIN 51 + #endif + #ifndef SDSS + #define SDSS 53 + #endif + +#else + + #error "Unsupported board!" + +#endif + +#define SS_PIN SDSS diff --git a/Marlin/src/HAL/HAL_SAMD51/watchdog_SAMD51.cpp b/Marlin/src/HAL/HAL_SAMD51/watchdog_SAMD51.cpp new file mode 100644 index 0000000000..fad3410cff --- /dev/null +++ b/Marlin/src/HAL/HAL_SAMD51/watchdog_SAMD51.cpp @@ -0,0 +1,53 @@ +/** + * Marlin 3D Printer Firmware + * + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * SAMD51 HAL developed by Giuliano Zaro (AKA GMagician) + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + +#ifdef __SAMD51__ + +#include "../../inc/MarlinConfig.h" + +#if ENABLED(USE_WATCHDOG) + + #include "watchdog_SAMD51.h" + + void watchdog_init(void) { + // The low-power oscillator used by the WDT runs at 32,768 Hz with + // a 1:32 prescale, thus 1024 Hz, though probably not super precise. + + // Setup WDT clocks + MCLK->APBAMASK.bit.OSC32KCTRL_ = true; + MCLK->APBAMASK.bit.WDT_ = true; + OSC32KCTRL->OSCULP32K.bit.EN1K = true; // Enable out 1K (this is what WDT uses) + + WDT->CTRLA.bit.ENABLE = false; // Disable watchdog for config + SYNC(WDT->SYNCBUSY.bit.ENABLE); + + WDT->INTENCLR.reg = WDT_INTENCLR_EW; // Disable early warning interrupt + WDT->CONFIG.reg = WDT_CONFIG_PER_CYC4096; // Set at least 4s period for chip reset + + watchdog_reset(); + + WDT->CTRLA.reg = WDT_CTRLA_ENABLE; // Start watchdog now in normal mode + SYNC(WDT->SYNCBUSY.bit.ENABLE); + } + +#endif // USE_WATCHDOG + +#endif // __SAMD51__ diff --git a/Marlin/src/HAL/HAL_SAMD51/watchdog_SAMD51.h b/Marlin/src/HAL/HAL_SAMD51/watchdog_SAMD51.h new file mode 100644 index 0000000000..1c4e7542f2 --- /dev/null +++ b/Marlin/src/HAL/HAL_SAMD51/watchdog_SAMD51.h @@ -0,0 +1,31 @@ +/** + * Marlin 3D Printer Firmware + * + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * SAMD51 HAL developed by Giuliano Zaro (AKA GMagician) + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +// Initialize watchdog with a 4 second interrupt time +void watchdog_init(); + +// Reset watchdog. MUST be called at least every 4 seconds after the +// first watchdog_init or SAMD will go into emergency procedures. +inline void watchdog_reset() { + SYNC(WDT->SYNCBUSY.bit.CLEAR); // Test first if previous is 'ongoing' to save time waiting for command execution + WDT->CLEAR.reg = WDT_CLEAR_CLEAR_KEY; +} diff --git a/Marlin/src/HAL/HAL_STM32/HAL.cpp b/Marlin/src/HAL/HAL_STM32/HAL.cpp index 8eb3c588f6..dc21069dba 100644 --- a/Marlin/src/HAL/HAL_STM32/HAL.cpp +++ b/Marlin/src/HAL/HAL_STM32/HAL.cpp @@ -28,54 +28,25 @@ #include "../../inc/MarlinConfig.h" #include "../shared/Delay.h" -#if ENABLED(EEPROM_EMULATED_WITH_SRAM) +#if ENABLED(SRAM_EEPROM_EMULATION) #if STM32F7xx #include "stm32f7xx_ll_pwr.h" #elif STM32F4xx #include "stm32f4xx_ll_pwr.h" #else - #error "EEPROM_EMULATED_WITH_SRAM is currently only supported for STM32F4xx and STM32F7xx" + #error "SRAM_EEPROM_EMULATION is currently only supported for STM32F4xx and STM32F7xx" #endif #endif -// -------------------------------------------------------------------------- -// Externals -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Local defines -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Types -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Variables -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- +// ------------------------ // Public Variables -// -------------------------------------------------------------------------- +// ------------------------ uint16_t HAL_adc_result; -// -------------------------------------------------------------------------- -// Private Variables -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Function prototypes -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Private functions -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- +// ------------------------ // Public functions -// -------------------------------------------------------------------------- - +// ------------------------ // Needed for DELAY_NS() / DELAY_US() on CORTEX-M7 #if (defined(__arm__) || defined(__thumb__)) && __CORTEX_M == 7 @@ -100,7 +71,7 @@ void HAL_init(void) { OUT_WRITE(LED_PIN, LOW); #endif - #if ENABLED(EEPROM_EMULATED_WITH_SRAM) + #if ENABLED(SRAM_EEPROM_EMULATION) // Enable access to backup SRAM __HAL_RCC_PWR_CLK_ENABLE(); HAL_PWR_EnableBkUpAccess(); @@ -129,9 +100,9 @@ extern "C" { extern unsigned int _ebss; // end of bss section } -// -------------------------------------------------------------------------- +// ------------------------ // ADC -// -------------------------------------------------------------------------- +// ------------------------ void HAL_adc_start_conversion(const uint8_t adc_pin) { HAL_adc_result = analogRead(adc_pin); diff --git a/Marlin/src/HAL/HAL_STM32/HAL.h b/Marlin/src/HAL/HAL_STM32/HAL.h index cb810d3f9f..051cab46d9 100644 --- a/Marlin/src/HAL/HAL_STM32/HAL.h +++ b/Marlin/src/HAL/HAL_STM32/HAL.h @@ -24,10 +24,6 @@ #define CPU_32_BIT -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - #include "../../core/macros.h" #include "../shared/Marduino.h" #include "../shared/math_32bit.h" @@ -43,9 +39,9 @@ #include #endif -// -------------------------------------------------------------------------- +// ------------------------ // Defines -// -------------------------------------------------------------------------- +// ------------------------ #if SERIAL_PORT == 0 #error "Serial port 0 does not exist" @@ -128,24 +124,24 @@ #undef pgm_read_ptr #define pgm_read_ptr(addr) (*(addr)) -// -------------------------------------------------------------------------- +// ------------------------ // Types -// -------------------------------------------------------------------------- +// ------------------------ -typedef int8_t pin_t; +typedef int16_t pin_t; #define HAL_SERVO_LIB libServo -// -------------------------------------------------------------------------- +// ------------------------ // Public Variables -// -------------------------------------------------------------------------- +// ------------------------ /** result of last ADC conversion */ extern uint16_t HAL_adc_result; -// -------------------------------------------------------------------------- +// ------------------------ // Public functions -// -------------------------------------------------------------------------- +// ------------------------ // Memory related #define __bss_end __bss_end__ diff --git a/Marlin/src/HAL/HAL_STM32/HAL_spi_STM32.cpp b/Marlin/src/HAL/HAL_STM32/HAL_spi_STM32.cpp index cde28e7e14..b2df7a16a7 100644 --- a/Marlin/src/HAL/HAL_STM32/HAL_spi_STM32.cpp +++ b/Marlin/src/HAL/HAL_STM32/HAL_spi_STM32.cpp @@ -23,35 +23,31 @@ #if defined(ARDUINO_ARCH_STM32) && !defined(STM32GENERIC) -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - #include "../../inc/MarlinConfig.h" #include -// -------------------------------------------------------------------------- +// ------------------------ // Public Variables -// -------------------------------------------------------------------------- +// ------------------------ static SPISettings spiConfig; -// -------------------------------------------------------------------------- +// ------------------------ // Public functions -// -------------------------------------------------------------------------- +// ------------------------ #if ENABLED(SOFTWARE_SPI) - // -------------------------------------------------------------------------- + // ------------------------ // Software SPI - // -------------------------------------------------------------------------- + // ------------------------ #error "Software SPI not supported for STM32. Use Hardware SPI." #else -// -------------------------------------------------------------------------- +// ------------------------ // Hardware SPI -// -------------------------------------------------------------------------- +// ------------------------ /** * VGPV SPI speed start and PCLK2/2, by default 108/2 = 54Mhz diff --git a/Marlin/src/HAL/HAL_STM32/HAL_timers_STM32.cpp b/Marlin/src/HAL/HAL_STM32/HAL_timers_STM32.cpp index f309b43f3a..beefdb3083 100644 --- a/Marlin/src/HAL/HAL_STM32/HAL_timers_STM32.cpp +++ b/Marlin/src/HAL/HAL_STM32/HAL_timers_STM32.cpp @@ -19,53 +19,28 @@ * along with this program. If not, see . * */ + #if defined(ARDUINO_ARCH_STM32) && !defined(STM32GENERIC) - -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - #include "HAL.h" #include "HAL_timers_STM32.h" -// -------------------------------------------------------------------------- -// Externals -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- +// ------------------------ // Local defines -// -------------------------------------------------------------------------- +// ------------------------ #define NUM_HARDWARE_TIMERS 2 -//#define PRESCALER 1 -// -------------------------------------------------------------------------- -// Types -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Public Variables -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- +// ------------------------ // Private Variables -// -------------------------------------------------------------------------- +// ------------------------ -stm32f4_timer_t TimerHandle[NUM_HARDWARE_TIMERS]; +stm32_timer_t TimerHandle[NUM_HARDWARE_TIMERS]; -// -------------------------------------------------------------------------- -// Function prototypes -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Private functions -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- +// ------------------------ // Public functions -// -------------------------------------------------------------------------- +// ------------------------ bool timers_initialized[NUM_HARDWARE_TIMERS] = { false }; diff --git a/Marlin/src/HAL/HAL_STM32/HAL_timers_STM32.h b/Marlin/src/HAL/HAL_STM32/HAL_timers_STM32.h index 8cdea0a81e..aefe880b4e 100644 --- a/Marlin/src/HAL/HAL_STM32/HAL_timers_STM32.h +++ b/Marlin/src/HAL/HAL_STM32/HAL_timers_STM32.h @@ -21,16 +21,12 @@ */ #pragma once -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - #include #include "../../inc/MarlinConfig.h" -// -------------------------------------------------------------------------- +// ------------------------ // Defines -// -------------------------------------------------------------------------- +// ------------------------ #define FORCE_INLINE __attribute__((always_inline)) inline @@ -128,21 +124,21 @@ extern void Temp_Handler(stimer_t *htim); #define HAL_STEP_TIMER_ISR() void Step_Handler(stimer_t *htim) #define HAL_TEMP_TIMER_ISR() void Temp_Handler(stimer_t *htim) -// -------------------------------------------------------------------------- +// ------------------------ // Types -// -------------------------------------------------------------------------- +// ------------------------ -typedef stimer_t stm32f4_timer_t; +typedef stimer_t stm32_timer_t; -// -------------------------------------------------------------------------- +// ------------------------ // Public Variables -// -------------------------------------------------------------------------- +// ------------------------ -extern stm32f4_timer_t TimerHandle[]; +extern stm32_timer_t TimerHandle[]; -// -------------------------------------------------------------------------- +// ------------------------ // Public functions -// -------------------------------------------------------------------------- +// ------------------------ void HAL_timer_start(const uint8_t timer_num, const uint32_t frequency); void HAL_timer_enable_interrupt(const uint8_t timer_num); diff --git a/Marlin/src/HAL/HAL_STM32/fastio_STM32.h b/Marlin/src/HAL/HAL_STM32/fastio_STM32.h index fd97fd206c..29ddf5faa3 100644 --- a/Marlin/src/HAL/HAL_STM32/fastio_STM32.h +++ b/Marlin/src/HAL/HAL_STM32/fastio_STM32.h @@ -27,25 +27,25 @@ * These use GPIO register access for fast port manipulation. */ -// -------------------------------------------------------------------------- +// ------------------------ // Public Variables -// -------------------------------------------------------------------------- +// ------------------------ extern GPIO_TypeDef * FastIOPortMap[]; -// -------------------------------------------------------------------------- +// ------------------------ // Public functions -// -------------------------------------------------------------------------- +// ------------------------ void FastIO_init(); // Must be called before using fast io macros -// -------------------------------------------------------------------------- +// ------------------------ // Defines -// -------------------------------------------------------------------------- +// ------------------------ #define _BV32(b) (1UL << (b)) -#if !defined(PWM) +#ifndef PWM #define PWM OUTPUT #endif diff --git a/Marlin/src/HAL/HAL_STM32/inc/Conditionals_LCD.h b/Marlin/src/HAL/HAL_STM32/inc/Conditionals_LCD.h new file mode 100644 index 0000000000..85f26f4016 --- /dev/null +++ b/Marlin/src/HAL/HAL_STM32/inc/Conditionals_LCD.h @@ -0,0 +1,22 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once diff --git a/Marlin/src/HAL/HAL_STM32/inc/Conditionals_adv.h b/Marlin/src/HAL/HAL_STM32/inc/Conditionals_adv.h new file mode 100644 index 0000000000..85f26f4016 --- /dev/null +++ b/Marlin/src/HAL/HAL_STM32/inc/Conditionals_adv.h @@ -0,0 +1,22 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once diff --git a/Marlin/src/HAL/HAL_STM32/inc/Conditionals_post.h b/Marlin/src/HAL/HAL_STM32/inc/Conditionals_post.h new file mode 100644 index 0000000000..85f26f4016 --- /dev/null +++ b/Marlin/src/HAL/HAL_STM32/inc/Conditionals_post.h @@ -0,0 +1,22 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once diff --git a/Marlin/src/HAL/HAL_STM32/SanityCheck.h b/Marlin/src/HAL/HAL_STM32/inc/SanityCheck.h similarity index 100% rename from Marlin/src/HAL/HAL_STM32/SanityCheck.h rename to Marlin/src/HAL/HAL_STM32/inc/SanityCheck.h diff --git a/Marlin/src/HAL/HAL_STM32/persistent_store_impl.cpp b/Marlin/src/HAL/HAL_STM32/persistent_store_impl.cpp index 01d7167b93..c94bce3b65 100644 --- a/Marlin/src/HAL/HAL_STM32/persistent_store_impl.cpp +++ b/Marlin/src/HAL/HAL_STM32/persistent_store_impl.cpp @@ -24,24 +24,24 @@ #include "../../inc/MarlinConfig.h" -#if ENABLED(EEPROM_SETTINGS) +#if ENABLED(EEPROM_SETTINGS) && ANY(FLASH_EEPROM_EMULATION, SRAM_EEPROM_EMULATION, SPI_EEPROM, I2C_EEPROM) #include "../shared/persistent_store_api.h" -#if DISABLED(EEPROM_EMULATED_WITH_SRAM, SPI_EEPROM, I2C_EEPROM) +#if ENABLED(FLASH_EEPROM_EMULATION) #include static bool eeprom_data_written = false; #endif bool PersistentStore::access_start() { - #if DISABLED(EEPROM_EMULATED_WITH_SRAM, SPI_EEPROM, I2C_EEPROM) + #if ENABLED(FLASH_EEPROM_EMULATION) eeprom_buffer_fill(); #endif return true; } bool PersistentStore::access_finish() { - #if DISABLED(EEPROM_EMULATED_WITH_SRAM, SPI_EEPROM, I2C_EEPROM) + #if ENABLED(FLASH_EEPROM_EMULATION) if (eeprom_data_written) { eeprom_buffer_flush(); eeprom_data_written = false; @@ -66,7 +66,7 @@ bool PersistentStore::write_data(int &pos, const uint8_t *value, size_t size, ui return true; } } - #elif DISABLED(EEPROM_EMULATED_WITH_SRAM) + #elif ENABLED(FLASH_EEPROM_EMULATION) eeprom_buffered_write_byte(pos, v); #else *(__IO uint8_t *)(BKPSRAM_BASE + (uint8_t * const)pos) = v; @@ -76,20 +76,20 @@ bool PersistentStore::write_data(int &pos, const uint8_t *value, size_t size, ui pos++; value++; }; - #if DISABLED(EEPROM_EMULATED_WITH_SRAM, SPI_EEPROM, I2C_EEPROM) + #if ENABLED(FLASH_EEPROM_EMULATION) eeprom_data_written = true; #endif return false; } -bool PersistentStore::read_data(int &pos, uint8_t* value, size_t size, uint16_t *crc, const bool writing) { +bool PersistentStore::read_data(int &pos, uint8_t* value, size_t size, uint16_t *crc, const bool writing/*=true*/) { do { // Read from either external EEPROM, program flash or Backup SRAM const uint8_t c = ( #if EITHER(SPI_EEPROM, I2C_EEPROM) eeprom_read_byte((uint8_t*)pos) - #elif DISABLED(EEPROM_EMULATED_WITH_SRAM) + #elif ENABLED(FLASH_EEPROM_EMULATION) eeprom_buffered_read_byte(pos) #else (*(__IO uint8_t *)(BKPSRAM_BASE + ((uint8_t*)pos))) @@ -105,14 +105,14 @@ bool PersistentStore::read_data(int &pos, uint8_t* value, size_t size, uint16_t } size_t PersistentStore::capacity() { - #if EITHER(SPI_EEPROM, I2C_EEPROM) - return E2END + 1; - #elif DISABLED(EEPROM_EMULATED_WITH_SRAM) - return E2END + 1; - #else - return 4096; // 4kB - #endif + return ( + #if ENABLED(SRAM_EEPROM_EMULATION) + 4096 // 4kB + #else + E2END + 1 + #endif + ); } -#endif // EEPROM_SETTINGS +#endif // EEPROM_SETTINGS && (FLASH_EEPROM_EMULATION || SRAM_EEPROM_EMULATION || SPI_EEPROM || I2C_EEPROM) #endif // ARDUINO_ARCH_STM32 && !STM32GENERIC diff --git a/Marlin/src/HAL/HAL_STM32/persistent_store_sdcard.cpp b/Marlin/src/HAL/HAL_STM32/persistent_store_sdcard.cpp new file mode 100644 index 0000000000..de9ed17a3d --- /dev/null +++ b/Marlin/src/HAL/HAL_STM32/persistent_store_sdcard.cpp @@ -0,0 +1,104 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + +/** + * HAL for stm32duino.com based on Libmaple and compatible (STM32F1) + * Implementation of EEPROM settings in SD Card + */ + +#ifdef TARGET_STM32F4 + +#include "../../inc/MarlinConfig.h" + +#if ENABLED(EEPROM_SETTINGS) && NONE(FLASH_EEPROM_EMULATION, SPI_EEPROM, I2C_EEPROM) + +#include "../shared/persistent_store_api.h" + +#ifndef E2END + #define E2END 0xFFF // 4KB +#endif +#define HAL_EEPROM_SIZE (E2END + 1) // 16KB + +#define _ALIGN(x) __attribute__ ((aligned(x))) // SDIO uint32_t* compat. +static char _ALIGN(4) HAL_eeprom_data[HAL_EEPROM_SIZE]; + +#if ENABLED(SDSUPPORT) + + #include "../../sd/cardreader.h" + + #define EEPROM_FILENAME "eeprom.dat" + + bool PersistentStore::access_start() { + if (!card.isDetected()) return false; + + SdFile file, root = card.getroot(); + if (!file.open(&root, EEPROM_FILENAME, O_RDONLY)) + return false; + + int16_t bytes_read = file.read(HAL_eeprom_data, HAL_STM32F4_EEPROM_SIZE); + if (bytes_read < 0) return false; + for (; bytes_read < HAL_STM32F4_EEPROM_SIZE; bytes_read++) + HAL_eeprom_data[bytes_read] = 0xFF; + file.close(); + return true; + } + + bool PersistentStore::access_finish() { + if (!card.isDetected()) return false; + + SdFile file, root = card.getroot(); + int16_t bytes_written = 0; + if (file.open(&root, EEPROM_FILENAME, O_CREAT | O_WRITE | O_TRUNC)) { + bytes_written = file.write(HAL_eeprom_data, HAL_STM32F4_EEPROM_SIZE); + file.close(); + } + return (bytes_written == HAL_STM32F4_EEPROM_SIZE); + } + +#else // !SDSUPPORT + + #error "Please define SPI_EEPROM (in Configuration.h) or disable EEPROM_SETTINGS." + +#endif // !SDSUPPORT + +bool PersistentStore::write_data(int &pos, const uint8_t *value, size_t size, uint16_t *crc) { + for (size_t i = 0; i < size; i++) + HAL_eeprom_data[pos + i] = value[i]; + crc16(crc, value, size); + pos += size; + return false; +} + +bool PersistentStore::read_data(int &pos, uint8_t* value, const size_t size, uint16_t *crc, const bool writing/*=true*/) { + for (size_t i = 0; i < size; i++) { + uint8_t c = HAL_eeprom_data[pos + i]; + if (writing) value[i] = c; + crc16(crc, &c, 1); + } + pos += size; + return false; +} + +size_t PersistentStore::capacity() { return HAL_STM32F4_EEPROM_SIZE; } + +#endif // EEPROM_SETTINGS +#endif // __STM32F4__ diff --git a/Marlin/src/HAL/HAL_STM32/pinsDebug.h b/Marlin/src/HAL/HAL_STM32/pinsDebug.h index 3759c2d6c3..4e27cee195 100644 --- a/Marlin/src/HAL/HAL_STM32/pinsDebug.h +++ b/Marlin/src/HAL/HAL_STM32/pinsDebug.h @@ -1 +1,34 @@ -#error "PINS_DEBUGGING is not yet supported for STM32!" +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +#if !(defined(NUM_DIGITAL_PINS) || defined(BOARD_NR_GPIO_PINS)) + #error "M43 not supported for this board" +#endif + +// Strange - STM32F4 comes to HAL_STM32 rather than HAL_STM32F4 for these files +#ifdef STM32F4 + #ifdef NUM_DIGITAL_PINS // Only in ST's Arduino core (STM32duino, STM32Core) + #include "pinsDebug_STM32duino.h" + #elif defined(BOARD_NR_GPIO_PINS) // Only in STM32GENERIC (Maple) + #include "pinsDebug_STM32GENERIC.h" + #else + #error "M43 not supported for this board" + #endif +#endif diff --git a/Marlin/src/HAL/HAL_STM32/pinsDebug_STM32GENERIC.h b/Marlin/src/HAL/HAL_STM32/pinsDebug_STM32GENERIC.h new file mode 100644 index 0000000000..3e66fda657 --- /dev/null +++ b/Marlin/src/HAL/HAL_STM32/pinsDebug_STM32GENERIC.h @@ -0,0 +1,123 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Support routines for STM32GENERIC (Maple) + */ + +/** + * Translation of routines & variables used by pinsDebug.h + */ + +#ifdef BOARD_NR_GPIO_PINS // Only in STM32GENERIC (Maple) + +#ifdef __STM32F1__ + #include "../HAL_STM32F1/fastio_STM32F1.h" +#elif defined(STM32F4) || defined(STM32F7) + #include "../HAL_STM32_F4_F7/fastio_STM32_F4_F7.h" +#endif + +extern const stm32_pin_info PIN_MAP[BOARD_NR_GPIO_PINS]; + +#define NUM_DIGITAL_PINS BOARD_NR_GPIO_PINS +#define NUMBER_PINS_TOTAL BOARD_NR_GPIO_PINS +#define VALID_PIN(pin) (pin >= 0 && pin < BOARD_NR_GPIO_PINS) +#define GET_ARRAY_PIN(p) pin_t(pin_array[p].pin) +#define pwm_status(pin) PWM_PIN(pin) +#define digitalRead_mod(p) extDigitalRead(p) +#define PRINT_PIN(p) do{ sprintf_P(buffer, PSTR("%3hd "), int16_t(p)); SERIAL_ECHO(buffer); }while(0) +#define PRINT_PORT(p) print_port(p) +#define PRINT_ARRAY_NAME(x) do{ sprintf_P(buffer, PSTR("%-" STRINGIFY(MAX_NAME_LENGTH) "s"), pin_array[x].name); SERIAL_ECHO(buffer); }while(0) +#define MULTI_NAME_PAD 21 // space needed to be pretty if not first name assigned to a pin + +// pins that will cause hang/reset/disconnect in M43 Toggle and Watch utilities +#ifndef M43_NEVER_TOUCH + #define M43_NEVER_TOUCH(Q) (Q >= 9 && Q <= 12) // SERIAL/USB pins PA9(TX) PA10(RX) +#endif + +static inline int8_t get_pin_mode(pin_t pin) { + return VALID_PIN(pin) ? _GET_MODE(pin) : -1; +} + +static inline pin_t DIGITAL_PIN_TO_ANALOG_PIN(pin_t pin) { + if (!VALID_PIN(pin)) return -1; + int8_t adc_channel = int8_t(PIN_MAP[pin].adc_channel); + #ifdef NUM_ANALOG_INPUTS + if (adc_channel >= NUM_ANALOG_INPUTS) adc_channel = ADCx; + #endif + return pin_t(adc_channel); +} + +static inline bool IS_ANALOG(pin_t pin) { + if (!VALID_PIN(pin)) return false; + if (PIN_MAP[pin].adc_channel != ADCx) { + #ifdef NUM_ANALOG_INPUTS + if (PIN_MAP[pin].adc_channel >= NUM_ANALOG_INPUTS) return false; + #endif + return _GET_MODE(pin) == GPIO_INPUT_ANALOG && !M43_NEVER_TOUCH(pin); + } + return false; +} + +static inline bool GET_PINMODE(const pin_t pin) { + return VALID_PIN(pin) && !IS_INPUT(pin); +} + +static inline bool GET_ARRAY_IS_DIGITAL(const int16_t array_pin) { + const pin_t pin = GET_ARRAY_PIN(array_pin); + return (!IS_ANALOG(pin) + #ifdef NUM_ANALOG_INPUTS + || PIN_MAP[pin].adc_channel >= NUM_ANALOG_INPUTS + #endif + ); +} + +#include "../../inc/MarlinConfig.h" // Allow pins/pins.h to set density + +static inline void pwm_details(const pin_t pin) { + if (PWM_PIN(pin)) { + timer_dev * const tdev = PIN_MAP[pin].timer_device; + const uint8_t channel = PIN_MAP[pin].timer_channel; + const char num = ( + #if defined(STM32_HIGH_DENSITY) || defined(STM32_XL_DENSITY) + tdev == &timer8 ? '8' : + tdev == &timer5 ? '5' : + #endif + tdev == &timer4 ? '4' : + tdev == &timer3 ? '3' : + tdev == &timer2 ? '2' : + tdev == &timer1 ? '1' : '?' + ); + char buffer[10]; + sprintf_P(buffer, PSTR(" TIM%c CH%c"), num, ('0' + channel)); + SERIAL_ECHO(buffer); + } +} + +static inline void print_port(pin_t pin) { + const char port = 'A' + char(pin >> 4); // pin div 16 + const int16_t gbit = PIN_MAP[pin].gpio_bit; + char buffer[8]; + sprintf_P(buffer, PSTR("P%c%hd "), port, gbit); + if (gbit < 10) SERIAL_CHAR(' '); + SERIAL_ECHO(buffer); +} + +#endif // BOARD_NR_GPIO_PINS diff --git a/Marlin/src/HAL/HAL_STM32/pinsDebug_STM32duino.h b/Marlin/src/HAL/HAL_STM32/pinsDebug_STM32duino.h new file mode 100644 index 0000000000..92d14d027a --- /dev/null +++ b/Marlin/src/HAL/HAL_STM32/pinsDebug_STM32duino.h @@ -0,0 +1,275 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +#include + +#ifdef NUM_DIGITAL_PINS // Only in ST's Arduino core (STM32duino, STM32Core) + +/** + * Life gets complicated if you want an easy to use 'M43 I' output (in port/pin order) + * because the variants in this platform do not always define all the I/O port/pins + * that a CPU has. + * + * VARIABLES: + * Ard_num - Arduino pin number - defined by the platform. It is used by digitalRead and + * digitalWrite commands and by M42. + * - does not contain port/pin info + * - is not in port/pin order + * - typically a variant will only assign Ard_num to port/pins that are actually used + * Index - M43 counter - only used to get Ard_num + * x - a parameter/argument used to search the pin_array to try to find a signal name + * associated with a Ard_num + * Port_pin - port number and pin number for use with CPU registers and printing reports + * + * Since M43 uses digitalRead and digitalWrite commands, only the Port_pins with an Ard_num + * are accessed and/or displayed. + * + * Three arrays are used. + * + * digitalPin[] is provided by the platform. It consists of the Port_pin numbers in + * Arduino pin number order. + * + * pin_array is a structure generated by the pins/pinsDebug.h header file. It is generated by + * the preprocessor. Only the signals associated with enabled options are in this table. + * It contains: + * - name of the signal + * - the Ard_num assigned by the pins_YOUR_BOARD.h file using the platform defines. + * EXAMPLE: "#define KILL_PIN PB1" results in Ard_num of 57. 57 is then used as an + * index into digitalPin[] to get the Port_pin number + * - if it is a digital or analog signal. PWMs are considered digital here. + * + * pin_xref is a structure generated by this header file. It is generated by the + * preprocessor. It is in port/pin order. It contains just the port/pin numbers defined by the + * platform for this variant. + * - Ard_num + * - printable version of Port_pin + * + * Routines with an "x" as a parameter/argument are used to search the pin_array to try to + * find a signal name associated with a port/pin. + * + * NOTE - the Arduino pin number is what is used by the M42 command, NOT the port/pin for that + * signal. The Arduino pin number is listed by the M43 I command. + */ + +extern const PinName digitalPin[]; // provided by the platform + +//////////////////////////////////////////////////////// +// +// make a list of the Arduino pin numbers in the Port/Pin order +// + +#define _PIN_ADD_2(NAME_ALPHA, ARDUINO_NUM) { {NAME_ALPHA}, ARDUINO_NUM }, +#define _PIN_ADD(NAME_ALPHA, ARDUINO_NUM) { NAME_ALPHA, ARDUINO_NUM }, +#define PIN_ADD(NAME) _PIN_ADD(#NAME, NAME) + +typedef struct { + char Port_pin_alpha[5]; + pin_t Ard_num; +} XrefInfo; + +const XrefInfo pin_xref[] PROGMEM = { + #include "pins_Xref.h" +}; + +//////////////////////////////////////////////////////////// + +#define MODE_PIN_INPUT 0 // Input mode (reset state) +#define MODE_PIN_OUTPUT 1 // General purpose output mode +#define MODE_PIN_ALT 2 // Alternate function mode +#define MODE_PIN_ANALOG 3 // Analog mode + +#define PIN_NUM(P) (P & 0x000F) +#define PIN_NUM_ALPHA_LEFT(P) (((P & 0x000F) < 10) ? ('0' + (P & 0x000F)) : '1') +#define PIN_NUM_ALPHA_RIGHT(P) (((P & 0x000F) > 9) ? ('0' + (P & 0x000F) - 10) : 0 ) +#define PORT_NUM(P) ((P >> 4) & 0x0007) +#define PORT_ALPHA(P) ('A' + (P >> 4)) + +/** + * Translation of routines & variables used by pinsDebug.h + */ +#define NUMBER_PINS_TOTAL NUM_DIGITAL_PINS +#define VALID_PIN(ANUM) ((ANUM) >= 0 && (ANUM) < NUMBER_PINS_TOTAL) +#define digitalRead_mod(Ard_num) extDigitalRead(Ard_num) // must use Arduino pin numbers when doing reads +#define PRINT_PIN(Q) +#define PRINT_PORT(ANUM) port_print(ANUM) +#define DIGITAL_PIN_TO_ANALOG_PIN(ANUM) -1 // will report analog pin number in the print port routine +#define GET_PIN_MAP_PIN_M43(Index) pin_xref[Index].Ard_num + +// x is a variable used to search pin_array +#define GET_ARRAY_IS_DIGITAL(x) ((bool) pin_array[x].is_digital) +#define GET_ARRAY_PIN(x) ((pin_t) pin_array[x].pin) +#define PRINT_ARRAY_NAME(x) do{ sprintf_P(buffer, PSTR("%-" STRINGIFY(MAX_NAME_LENGTH) "s"), pin_array[x].name); SERIAL_ECHO(buffer); }while(0) +#define MULTI_NAME_PAD 33 // space needed to be pretty if not first name assigned to a pin + +#ifndef M43_NEVER_TOUCH + #define _M43_NEVER_TOUCH(Index) (Index >= 9 && Index <= 12) // SERIAL/USB pins: PA9(TX) PA10(RX) PA11(USB_DM) PA12(USB_DP) + #ifdef KILL_PIN + #define M43_NEVER_TOUCH(Index) m43_never_touch(Index) + + bool m43_never_touch(const pin_t Index) { + static pin_t M43_kill_index = -1; + if (M43_kill_index < 0) + for (M43_kill_index = 0; M43_kill_index < NUMBER_PINS_TOTAL; M43_kill_index++) + if (KILL_PIN == GET_PIN_MAP_PIN_M43(M43_kill_index)) break; + return _M43_NEVER_TOUCH(Index) || Index == M43_kill_index; // KILL_PIN and SERIAL/USB + } + #else + #define M43_NEVER_TOUCH(Index) _M43_NEVER_TOUCH(Index) + #endif +#endif + +uint8_t get_pin_mode(const pin_t Ard_num) { + uint32_t mode_all = 0; + const PinName dp = digitalPin[Ard_num]; + switch (PORT_ALPHA(dp)) { + case 'A' : mode_all = GPIOA->MODER; break; + case 'B' : mode_all = GPIOB->MODER; break; + case 'C' : mode_all = GPIOC->MODER; break; + case 'D' : mode_all = GPIOD->MODER; break; + #ifdef PE_0 + case 'E' : mode_all = GPIOE->MODER; break; + #elif defined (PF_0) + case 'F' : mode_all = GPIOF->MODER; break; + #elif defined (PG_0) + case 'G' : mode_all = GPIOG->MODER; break; + #elif defined (PH_0) + case 'H' : mode_all = GPIOH->MODER; break; + #elif defined (PI_0) + case 'I' : mode_all = GPIOI->MODER; break; + #elif defined (PJ_0) + case 'J' : mode_all = GPIOJ->MODER; break; + #elif defined (PK_0) + case 'K' : mode_all = GPIOK->MODER; break; + #elif defined (PL_0) + case 'L' : mode_all = GPIOL->MODER; break; + #endif + } + return (mode_all >> (2 * uint8_t(PIN_NUM(dp)))) & 0x03; +} + +bool GET_PINMODE(const pin_t Ard_num) { + const uint8_t pin_mode = get_pin_mode(Ard_num); + return pin_mode == MODE_PIN_OUTPUT || pin_mode == MODE_PIN_ALT; // assume all alt definitions are PWM +} + +int8_t digital_pin_to_analog_pin(pin_t Ard_num) { + Ard_num -= NUM_ANALOG_FIRST; + return (Ard_num >= 0 && Ard_num < NUM_ANALOG_INPUTS) ? Ard_num : -1; +} + +bool IS_ANALOG(const pin_t Ard_num) { + return get_pin_mode(Ard_num) == MODE_PIN_ANALOG; +} + +bool is_digital(const pin_t x) { + const uint8_t pin_mode = get_pin_mode(pin_array[x].pin); + return pin_mode == MODE_PIN_INPUT || pin_mode == MODE_PIN_OUTPUT; +} + +void port_print(const pin_t Ard_num) { + char buffer[16]; + pin_t Index; + for (Index = 0; Index < NUMBER_PINS_TOTAL; Index++) + if (Ard_num == GET_PIN_MAP_PIN_M43(Index)) break; + + char * const ppa = pin_xref[Index].Port_pin_alpha; + sprintf_P(buffer, PSTR("%s"), ppa); + SERIAL_ECHO(buffer); + if (ppa[3] == '\0') SERIAL_CHAR(' '); + + // print analog pin number + const int8_t Port_pin = digital_pin_to_analog_pin(Ard_num); + if (Port_pin >= 0) { + sprintf_P(buffer, PSTR(" (A%d) "), Port_pin); + SERIAL_ECHO(buffer); + if (Port_pin < 10) SERIAL_CHAR(' '); + } + else + SERIAL_ECHO_SP(7); + + // Print number to be used with M42 + sprintf_P(buffer, PSTR(" M42 P%d "), Ard_num); + SERIAL_ECHO(buffer); + if (Ard_num < 10) SERIAL_CHAR(' '); + if (Ard_num < 100) SERIAL_CHAR(' '); +} + +bool pwm_status(const pin_t Ard_num) { + return get_pin_mode(Ard_num) == MODE_PIN_ALT; +} + +void pwm_details(const pin_t Ard_num) { + if (pwm_status(Ard_num)) { + uint32_t alt_all = 0; + const PinName dp = digitalPin[Ard_num]; + pin_t pin_number = uint8_t(PIN_NUM(dp)); + const bool over_7 = pin_number >= 8; + const uint8_t ind = over_7 ? 1 : 0; + switch (PORT_ALPHA(dp)) { // get alt function + case 'A' : alt_all = GPIOA->AFR[ind]; break; + case 'B' : alt_all = GPIOB->AFR[ind]; break; + case 'C' : alt_all = GPIOC->AFR[ind]; break; + case 'D' : alt_all = GPIOD->AFR[ind]; break; + #ifdef PE_0 + case 'E' : alt_all = GPIOE->AFR[ind]; break; + #elif defined (PF_0) + case 'F' : alt_all = GPIOF->AFR[ind]; break; + #elif defined (PG_0) + case 'G' : alt_all = GPIOG->AFR[ind]; break; + #elif defined (PH_0) + case 'H' : alt_all = GPIOH->AFR[ind]; break; + #elif defined (PI_0) + case 'I' : alt_all = GPIOI->AFR[ind]; break; + #elif defined (PJ_0) + case 'J' : alt_all = GPIOJ->AFR[ind]; break; + #elif defined (PK_0) + case 'K' : alt_all = GPIOK->AFR[ind]; break; + #elif defined (PL_0) + case 'L' : alt_all = GPIOL->AFR[ind]; break; + #endif + } + if (over_7) pin_number -= 8; + + uint8_t alt_func = (alt_all >> (4 * pin_number)) & 0x0F; + SERIAL_ECHOPAIR("Alt Function: ", alt_func); + if (alt_func < 10) SERIAL_CHAR(' '); + SERIAL_ECHOPGM(" - "); + switch (alt_func) { + case 0 : SERIAL_ECHOPGM("system (misc. I/O)"); break; + case 1 : SERIAL_ECHOPGM("TIM1/TIM2 (probably PWM)"); break; + case 2 : SERIAL_ECHOPGM("TIM3..5 (probably PWM)"); break; + case 3 : SERIAL_ECHOPGM("TIM8..11 (probably PWM)"); break; + case 4 : SERIAL_ECHOPGM("I2C1..3"); break; + case 5 : SERIAL_ECHOPGM("SPI1/SPI2"); break; + case 6 : SERIAL_ECHOPGM("SPI3"); break; + case 7 : SERIAL_ECHOPGM("USART1..3"); break; + case 8 : SERIAL_ECHOPGM("USART4..6"); break; + case 9 : SERIAL_ECHOPGM("CAN1/CAN2, TIM12..14 (probably PWM)"); break; + case 10 : SERIAL_ECHOPGM("OTG"); break; + case 11 : SERIAL_ECHOPGM("ETH"); break; + case 12 : SERIAL_ECHOPGM("FSMC, SDIO, OTG"); break; + case 13 : SERIAL_ECHOPGM("DCMI"); break; + case 14 : SERIAL_ECHOPGM("unused (shouldn't see this)"); break; + case 15 : SERIAL_ECHOPGM("EVENTOUT"); break; + } + } +} // pwm_details + +#endif // NUM_DIGITAL_PINS diff --git a/Marlin/src/HAL/HAL_STM32/pins_Xref.h b/Marlin/src/HAL/HAL_STM32/pins_Xref.h new file mode 100644 index 0000000000..84278c3916 --- /dev/null +++ b/Marlin/src/HAL/HAL_STM32/pins_Xref.h @@ -0,0 +1,612 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + +// +// make a list of the Arduino pin numbers in the Port/Pin order +// +#ifdef PA0 + PIN_ADD(PA0) +#endif +#ifdef PA1 + PIN_ADD(PA1) +#endif +#ifdef PA2 + PIN_ADD(PA2) +#endif +#ifdef PA3 + PIN_ADD(PA3) +#endif +#ifdef PA4 + PIN_ADD(PA4) +#endif +#ifdef PA5 + PIN_ADD(PA5) +#endif +#ifdef PA6 + PIN_ADD(PA6) +#endif +#ifdef PA7 + PIN_ADD(PA7) +#endif +#ifdef PA8 + PIN_ADD(PA8) +#endif +#ifdef PA9 + PIN_ADD(PA9) +#endif +#ifdef PA10 + PIN_ADD(PA10) +#endif +#ifdef PA11 + PIN_ADD(PA11) +#endif +#ifdef PA12 + PIN_ADD(PA12) +#endif +#ifdef PA13 + PIN_ADD(PA13) +#endif +#ifdef PA14 + PIN_ADD(PA14) +#endif +#ifdef PA15 + PIN_ADD(PA15) +#endif + +#ifdef PB0 + PIN_ADD(PB0) +#endif +#ifdef PB1 + PIN_ADD(PB1) +#endif +#ifdef PB2 + PIN_ADD(PB2) +#endif +#ifdef PB3 + PIN_ADD(PB3) +#endif +#ifdef PB4 + PIN_ADD(PB4) +#endif +#ifdef PB5 + PIN_ADD(PB5) +#endif +#ifdef PB6 + PIN_ADD(PB6) +#endif +#ifdef PB7 + PIN_ADD(PB7) +#endif +#ifdef PB8 + PIN_ADD(PB8) +#endif +#ifdef PB9 + PIN_ADD(PB9) +#endif +#ifdef PB10 + PIN_ADD(PB10) +#endif +#ifdef PB11 + PIN_ADD(PB11) +#endif +#ifdef PB12 + PIN_ADD(PB12) +#endif +#ifdef PB13 + PIN_ADD(PB13) +#endif +#ifdef PB14 + PIN_ADD(PB14) +#endif +#ifdef PB15 + PIN_ADD(PB15) +#endif + +#ifdef PC0 + PIN_ADD(PC0) +#endif +#ifdef PC1 + PIN_ADD(PC1) +#endif +#ifdef PC2 + PIN_ADD(PC2) +#endif +#ifdef PC3 + PIN_ADD(PC3) +#endif +#ifdef PC4 + PIN_ADD(PC4) +#endif +#ifdef PC5 + PIN_ADD(PC5) +#endif +#ifdef PC6 + PIN_ADD(PC6) +#endif +#ifdef PC7 + PIN_ADD(PC7) +#endif +#ifdef PC8 + PIN_ADD(PC8) +#endif +#ifdef PC9 + PIN_ADD(PC9) +#endif +#ifdef PC10 + PIN_ADD(PC10) +#endif +#ifdef PC11 + PIN_ADD(PC11) +#endif +#ifdef PC12 + PIN_ADD(PC12) +#endif +#ifdef PC13 + PIN_ADD(PC13) +#endif +#ifdef PC14 + PIN_ADD(PC14) +#endif +#ifdef PC15 + PIN_ADD(PC15) +#endif + +#ifdef PD0 + PIN_ADD(PD0) +#endif +#ifdef PD1 + PIN_ADD(PD1) +#endif +#ifdef PD2 + PIN_ADD(PD2) +#endif +#ifdef PD3 + PIN_ADD(PD3) +#endif +#ifdef PD4 + PIN_ADD(PD4) +#endif +#ifdef PD5 + PIN_ADD(PD5) +#endif +#ifdef PD6 + PIN_ADD(PD6) +#endif +#ifdef PD7 + PIN_ADD(PD7) +#endif +#ifdef PD8 + PIN_ADD(PD8) +#endif +#ifdef PD9 + PIN_ADD(PD9) +#endif +#ifdef PD10 + PIN_ADD(PD10) +#endif +#ifdef PD11 + PIN_ADD(PD11) +#endif +#ifdef PD12 + PIN_ADD(PD12) +#endif +#ifdef PD13 + PIN_ADD(PD13) +#endif +#ifdef PD14 + PIN_ADD(PD14) +#endif +#ifdef PD15 + PIN_ADD(PD15) +#endif + +#ifdef PE0 + PIN_ADD(PE0) +#endif +#ifdef PE1 + PIN_ADD(PE1) +#endif +#ifdef PE2 + PIN_ADD(PE2) +#endif +#ifdef PE3 + PIN_ADD(PE3) +#endif +#ifdef PE4 + PIN_ADD(PE4) +#endif +#ifdef PE5 + PIN_ADD(PE5) +#endif +#ifdef PE6 + PIN_ADD(PE6) +#endif +#ifdef PE7 + PIN_ADD(PE7) +#endif +#ifdef PE8 + PIN_ADD(PE8) +#endif +#ifdef PE9 + PIN_ADD(PE9) +#endif +#ifdef PE10 + PIN_ADD(PE10) +#endif +#ifdef PE11 + PIN_ADD(PE11) +#endif +#ifdef PE12 + PIN_ADD(PE12) +#endif +#ifdef PE13 + PIN_ADD(PE13) +#endif +#ifdef PE14 + PIN_ADD(PE14) +#endif +#ifdef PE15 + PIN_ADD(PE15) +#endif + +#ifdef PF0 + PIN_ADD(PF0) +#endif +#ifdef PF1 + PIN_ADD(PF1) +#endif +#ifdef PF2 + PIN_ADD(PF2) +#endif +#ifdef PF3 + PIN_ADD(PF3) +#endif +#ifdef PF4 + PIN_ADD(PF4) +#endif +#ifdef PF5 + PIN_ADD(PF5) +#endif +#ifdef PF6 + PIN_ADD(PF6) +#endif +#ifdef PF7 + PIN_ADD(PF7) +#endif +#ifdef PF8 + PIN_ADD(PF8) +#endif +#ifdef PF9 + PIN_ADD(PF9) +#endif +#ifdef PF10 + PIN_ADD(PF10) +#endif +#ifdef PF11 + PIN_ADD(PF11) +#endif +#ifdef PF12 + PIN_ADD(PF12) +#endif +#ifdef PF13 + PIN_ADD(PF13) +#endif +#ifdef PF14 + PIN_ADD(PF14) +#endif +#ifdef PF15 + PIN_ADD(PF15) +#endif + +#ifdef PG0 + PIN_ADD(PG0) +#endif +#ifdef PG1 + PIN_ADD(PG1) +#endif +#ifdef PG2 + PIN_ADD(PG2) +#endif +#ifdef PG3 + PIN_ADD(PG3) +#endif +#ifdef PG4 + PIN_ADD(PG4) +#endif +#ifdef PG5 + PIN_ADD(PG5) +#endif +#ifdef PG6 + PIN_ADD(PG6) +#endif +#ifdef PG7 + PIN_ADD(PG7) +#endif +#ifdef PG8 + PIN_ADD(PG8) +#endif +#ifdef PG9 + PIN_ADD(PG9) +#endif +#ifdef PG10 + PIN_ADD(PG10) +#endif +#ifdef PG11 + PIN_ADD(PG11) +#endif +#ifdef PG12 + PIN_ADD(PG12) +#endif +#ifdef PG13 + PIN_ADD(PG13) +#endif +#ifdef PG14 + PIN_ADD(PG14) +#endif +#ifdef PG15 + PIN_ADD(PG15) +#endif + +#ifdef PH0 + PIN_ADD(PH0) +#endif +#ifdef PH1 + PIN_ADD(PH1) +#endif +#ifdef PH2 + PIN_ADD(PH2) +#endif +#ifdef PH3 + PIN_ADD(PH3) +#endif +#ifdef PH4 + PIN_ADD(PH4) +#endif +#ifdef PH5 + PIN_ADD(PH5) +#endif +#ifdef PH6 + PIN_ADD(PH6) +#endif +#ifdef PH7 + PIN_ADD(PH7) +#endif +#ifdef PH8 + PIN_ADD(PH8) +#endif +#ifdef PH9 + PIN_ADD(PH9) +#endif +#ifdef PH10 + PIN_ADD(PH10) +#endif +#ifdef PH11 + PIN_ADD(PH11) +#endif +#ifdef PH12 + PIN_ADD(PH12) +#endif +#ifdef PH13 + PIN_ADD(PH13) +#endif +#ifdef PH14 + PIN_ADD(PH14) +#endif +#ifdef PH15 + PIN_ADD(PH15) +#endif + +#ifdef PI0 + PIN_ADD(PI0) +#endif +#ifdef PI1 + PIN_ADD(PI1) +#endif +#ifdef PI2 + PIN_ADD(PI2) +#endif +#ifdef PI3 + PIN_ADD(PI3) +#endif +#ifdef PI4 + PIN_ADD(PI4) +#endif +#ifdef PI5 + PIN_ADD(PI5) +#endif +#ifdef PI6 + PIN_ADD(PI6) +#endif +#ifdef PI7 + PIN_ADD(PI7) +#endif +#ifdef PI8 + PIN_ADD(PI8) +#endif +#ifdef PI9 + PIN_ADD(PI9) +#endif +#ifdef PI10 + PIN_ADD(PI10) +#endif +#ifdef PI11 + PIN_ADD(PI11) +#endif +#ifdef PI12 + PIN_ADD(PI12) +#endif +#ifdef PI13 + PIN_ADD(PI13) +#endif +#ifdef PI14 + PIN_ADD(PI14) +#endif +#ifdef PI15 + PIN_ADD(PI15) +#endif + +#ifdef PJ0 + PIN_ADD(PJ0) +#endif +#ifdef PJ1 + PIN_ADD(PJ1) +#endif +#ifdef PJ2 + PIN_ADD(PJ2) +#endif +#ifdef PJ3 + PIN_ADD(PJ3) +#endif +#ifdef PJ4 + PIN_ADD(PJ4) +#endif +#ifdef PJ5 + PIN_ADD(PJ5) +#endif +#ifdef PJ6 + PIN_ADD(PJ6) +#endif +#ifdef PJ7 + PIN_ADD(PJ7) +#endif +#ifdef PJ8 + PIN_ADD(PJ8) +#endif +#ifdef PJ9 + PIN_ADD(PJ9) +#endif +#ifdef PJ10 + PIN_ADD(PJ10) +#endif +#ifdef PJ11 + PIN_ADD(PJ11) +#endif +#ifdef PJ12 + PIN_ADD(PJ12) +#endif +#ifdef PJ13 + PIN_ADD(PJ13) +#endif +#ifdef PJ14 + PIN_ADD(PJ14) +#endif +#ifdef PJ15 + PIN_ADD(PJ15) +#endif + +#ifdef PK0 + PIN_ADD(PK0) +#endif +#ifdef PK1 + PIN_ADD(PK1) +#endif +#ifdef PK2 + PIN_ADD(PK2) +#endif +#ifdef PK3 + PIN_ADD(PK3) +#endif +#ifdef PK4 + PIN_ADD(PK4) +#endif +#ifdef PK5 + PIN_ADD(PK5) +#endif +#ifdef PK6 + PIN_ADD(PK6) +#endif +#ifdef PK7 + PIN_ADD(PK7) +#endif +#ifdef PK8 + PIN_ADD(PK8) +#endif +#ifdef PK9 + PIN_ADD(PK9) +#endif +#ifdef PK10 + PIN_ADD(PK10) +#endif +#ifdef PK11 + PIN_ADD(PK11) +#endif +#ifdef PK12 + PIN_ADD(PK12) +#endif +#ifdef PK13 + PIN_ADD(PK13) +#endif +#ifdef PK14 + PIN_ADD(PK14) +#endif +#ifdef PK15 + PIN_ADD(PK15) +#endif + +#ifdef PL0 + PIN_ADD(PL0) +#endif +#ifdef PL1 + PIN_ADD(PL1) +#endif +#ifdef PL2 + PIN_ADD(PL2) +#endif +#ifdef PL3 + PIN_ADD(PL3) +#endif +#ifdef PL4 + PIN_ADD(PL4) +#endif +#ifdef PL5 + PIN_ADD(PL5) +#endif +#ifdef PL6 + PIN_ADD(PL6) +#endif +#ifdef PL7 + PIN_ADD(PL7) +#endif +#ifdef PL8 + PIN_ADD(PL8) +#endif +#ifdef PL9 + PIN_ADD(PL9) +#endif +#ifdef PL10 + PIN_ADD(PL10) +#endif +#ifdef PL11 + PIN_ADD(PL11) +#endif +#ifdef PL12 + PIN_ADD(PL12) +#endif +#ifdef PL13 + PIN_ADD(PL13) +#endif +#ifdef PL14 + PIN_ADD(PL14) +#endif +#ifdef PL15 + PIN_ADD(PL15) +#endif diff --git a/Marlin/src/HAL/HAL_STM32/watchdog_STM32.cpp b/Marlin/src/HAL/HAL_STM32/watchdog_STM32.cpp index 6f8b070e7b..ae9f1e3583 100644 --- a/Marlin/src/HAL/HAL_STM32/watchdog_STM32.cpp +++ b/Marlin/src/HAL/HAL_STM32/watchdog_STM32.cpp @@ -22,10 +22,12 @@ #if defined(ARDUINO_ARCH_STM32) && !defined(STM32GENERIC) -#include "../../inc/MarlinConfig.h" +#include "../../inc/MarlinConfigPre.h" #if ENABLED(USE_WATCHDOG) + #include "../../inc/MarlinConfig.h" + #include "watchdog_STM32.h" #include @@ -33,7 +35,7 @@ void watchdog_reset() { IWatchdog.reload(); - #if PIN_EXISTS(LED) + #if DISABLED(PINS_DEBUGGING) && PIN_EXISTS(LED) TOGGLE(LED_PIN); // heartbeat indicator #endif } diff --git a/Marlin/src/HAL/HAL_STM32F1/HAL.cpp b/Marlin/src/HAL/HAL_STM32F1/HAL.cpp index 2bbbd8b48b..17457343d0 100644 --- a/Marlin/src/HAL/HAL_STM32F1/HAL.cpp +++ b/Marlin/src/HAL/HAL_STM32F1/HAL.cpp @@ -27,22 +27,14 @@ #ifdef __STM32F1__ -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - #include "HAL.h" #include "../../inc/MarlinConfig.h" #include -// -------------------------------------------------------------------------- -// Externals -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- +// ------------------------ // Types -// -------------------------------------------------------------------------- +// ------------------------ #define __I #define __IO volatile @@ -70,13 +62,10 @@ __IO uint32_t CPACR; /*!< Offset: 0x088 (R/W) Coprocessor Access Control Register */ } SCB_Type; -// -------------------------------------------------------------------------- -// Variables -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- +// ------------------------ // Local defines -// -------------------------------------------------------------------------- +// ------------------------ + #define SCS_BASE (0xE000E000UL) /*!< System Control Space Base Address */ #define SCB_BASE (SCS_BASE + 0x0D00UL) /*!< System Control Block Base Address */ @@ -89,18 +78,19 @@ #define SCB_AIRCR_PRIGROUP_Pos 8 /*!< SCB AIRCR: PRIGROUP Position */ #define SCB_AIRCR_PRIGROUP_Msk (7UL << SCB_AIRCR_PRIGROUP_Pos) /*!< SCB AIRCR: PRIGROUP Mask */ -// -------------------------------------------------------------------------- +// ------------------------ // Public Variables -// -------------------------------------------------------------------------- +// ------------------------ + #ifdef SERIAL_USB USBSerial SerialUSB; #endif uint16_t HAL_adc_result; -// -------------------------------------------------------------------------- +// ------------------------ // Private Variables -// -------------------------------------------------------------------------- +// ------------------------ STM32ADC adc(ADC1); uint8_t adc_pins[] = { @@ -166,13 +156,13 @@ enum TEMP_PINS : char { uint16_t HAL_adc_results[ADC_PIN_COUNT]; -// -------------------------------------------------------------------------- +// ------------------------ // Function prototypes -// -------------------------------------------------------------------------- +// ------------------------ -// -------------------------------------------------------------------------- +// ------------------------ // Private functions -// -------------------------------------------------------------------------- +// ------------------------ static void NVIC_SetPriorityGrouping(uint32_t PriorityGroup) { uint32_t reg_value; uint32_t PriorityGroupTmp = (PriorityGroup & (uint32_t)0x07); /* only values 0..7 are used */ @@ -185,9 +175,9 @@ static void NVIC_SetPriorityGrouping(uint32_t PriorityGroup) { SCB->AIRCR = reg_value; } -// -------------------------------------------------------------------------- +// ------------------------ // Public functions -// -------------------------------------------------------------------------- +// ------------------------ // // Leave PA11/PA12 intact if USBSerial is not used @@ -211,6 +201,11 @@ void HAL_init(void) { #if PIN_EXISTS(LED) OUT_WRITE(LED_PIN, LOW); #endif + #if PIN_EXISTS(USB_CONNECT) + OUT_WRITE(USB_CONNECT_PIN, !USB_CONNECT_INVERTING); // USB clear connection + delay(1000); // Give OS time to notice + OUT_WRITE(USB_CONNECT_PIN, USB_CONNECT_INVERTING); + #endif } /* VGPV Done with defines @@ -263,14 +258,18 @@ extern "C" { } */ -// -------------------------------------------------------------------------- +// ------------------------ // ADC -// -------------------------------------------------------------------------- +// ------------------------ // Init the AD in continuous capture mode void HAL_adc_init(void) { // configure the ADC adc.calibrate(); - adc.setSampleRate(ADC_SMPR_41_5); // ? + #if F_CPU > 72000000 + adc.setSampleRate(ADC_SMPR_71_5); // 71.5 ADC cycles + #else + adc.setSampleRate(ADC_SMPR_41_5); // 41.5 ADC cycles + #endif adc.setPins(adc_pins, ADC_PIN_COUNT); adc.setDMA(HAL_adc_results, (uint16_t)ADC_PIN_COUNT, (uint32_t)(DMA_MINC_MODE | DMA_CIRC_MODE), nullptr); adc.setScanMode(); @@ -322,7 +321,7 @@ uint16_t analogRead(pin_t pin) { // Wrapper to maple unprotected analogWrite void analogWrite(pin_t pin, int pwm_val8) { - if (PWM_PIN(pin) && IS_OUTPUT(pin)) + if (PWM_PIN(pin)) analogWrite(uint8_t(pin), pwm_val8); } diff --git a/Marlin/src/HAL/HAL_STM32F1/HAL.h b/Marlin/src/HAL/HAL_STM32F1/HAL.h index 3f33e3ec1a..f0a4883504 100644 --- a/Marlin/src/HAL/HAL_STM32F1/HAL.h +++ b/Marlin/src/HAL/HAL_STM32F1/HAL.h @@ -28,14 +28,6 @@ #define CPU_32_BIT -#ifndef vsnprintf_P - #define vsnprintf_P vsnprintf -#endif - -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - #include "../../core/macros.h" #include "../shared/Marduino.h" #include "../shared/math_32bit.h" @@ -51,9 +43,9 @@ #include "../../inc/MarlinConfigPre.h" -// -------------------------------------------------------------------------- +// ------------------------ // Defines -// -------------------------------------------------------------------------- +// ------------------------ #ifdef SERIAL_USB #define UsbSerial Serial @@ -156,22 +148,22 @@ void HAL_init(void); #define RST_SOFTWARE 32 #define RST_BACKUP 64 -// -------------------------------------------------------------------------- +// ------------------------ // Types -// -------------------------------------------------------------------------- +// ------------------------ typedef int8_t pin_t; -// -------------------------------------------------------------------------- +// ------------------------ // Public Variables -// -------------------------------------------------------------------------- +// ------------------------ /** result of last ADC conversion */ extern uint16_t HAL_adc_result; -// -------------------------------------------------------------------------- +// ------------------------ // Public functions -// -------------------------------------------------------------------------- +// ------------------------ // Disable interrupts #define cli() noInterrupts() diff --git a/Marlin/src/HAL/HAL_STM32F1/HAL_sdio_STM32F1.cpp b/Marlin/src/HAL/HAL_STM32F1/HAL_sdio_STM32F1.cpp index 4f90b26e68..d2d59811a8 100644 --- a/Marlin/src/HAL/HAL_STM32F1/HAL_sdio_STM32F1.cpp +++ b/Marlin/src/HAL/HAL_STM32F1/HAL_sdio_STM32F1.cpp @@ -25,6 +25,8 @@ #include +#include "../../inc/MarlinConfig.h" // Allow pins/pins.h to set density + #if defined(STM32_HIGH_DENSITY) || defined(STM32_XL_DENSITY) #include "HAL_sdio_STM32F1.h" @@ -124,6 +126,8 @@ bool SDIO_ReadBlock(uint32_t blockAddress, uint8_t *data) { return false; } +uint32_t millis(); + bool SDIO_WriteBlock(uint32_t blockAddress, const uint8_t *data) { if (SDIO_GetCardState() != SDIO_CARD_TRANSFER) return false; if (blockAddress >= SdCard.LogBlockNbr) return false; @@ -165,9 +169,9 @@ bool SDIO_WriteBlock(uint32_t blockAddress, const uint8_t *data) { inline uint32_t SDIO_GetCardState(void) { return SDIO_CmdSendStatus(SdCard.RelCardAdd << 16U) ? (SDIO_GetResponse(SDIO_RESP1) >> 9U) & 0x0FU : SDIO_CARD_ERROR; } -// -------------------------------------------------------------------------- +// ------------------------ // SD Commands and Responses -// -------------------------------------------------------------------------- +// ------------------------ void SDIO_SendCommand(uint16_t command, uint32_t argument) { SDIO->ARG = argument; SDIO->CMD = (uint32_t)(SDIO_CMD_CPSMEN | command); } uint8_t SDIO_GetCommandResponse(void) { return (uint8_t)(SDIO->RESPCMD); } diff --git a/Marlin/src/HAL/HAL_STM32F1/HAL_sdio_STM32F1.h b/Marlin/src/HAL/HAL_STM32F1/HAL_sdio_STM32F1.h index 2d4eb5b879..2ff195d48f 100644 --- a/Marlin/src/HAL/HAL_STM32F1/HAL_sdio_STM32F1.h +++ b/Marlin/src/HAL/HAL_STM32F1/HAL_sdio_STM32F1.h @@ -21,18 +21,14 @@ */ #pragma once -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - #include "../shared/Marduino.h" -#include "libmaple/sdio.h" -#include "libmaple/dma.h" +#include +#include -// -------------------------------------------------------------------------- +// ------------------------ // Defines -// -------------------------------------------------------------------------- +// ------------------------ #define SDMMC_CMD_GO_IDLE_STATE ((uint8_t)0) /* Resets the SD memory card. */ #define SDMMC_CMD_ALL_SEND_CID ((uint8_t)2) /* Asks any card connected to the host to send the CID numbers on the CMD line. */ @@ -106,9 +102,9 @@ #define SDIO_CLOCK 18000000 /* 18 MHz */ -// -------------------------------------------------------------------------- +// ------------------------ // Types -// -------------------------------------------------------------------------- +// ------------------------ typedef struct { uint32_t CardType; // Card Type @@ -121,9 +117,9 @@ typedef struct { uint32_t LogBlockSize; // Logical block size in bytes } SDIO_CardInfoTypeDef; -// -------------------------------------------------------------------------- +// ------------------------ // Public functions -// -------------------------------------------------------------------------- +// ------------------------ inline uint32_t SDIO_GetCardState(void); diff --git a/Marlin/src/HAL/HAL_STM32F1/HAL_spi_Stm32f1.cpp b/Marlin/src/HAL/HAL_STM32F1/HAL_spi_Stm32f1.cpp index a43a1b4194..7ed37e5a38 100644 --- a/Marlin/src/HAL/HAL_STM32F1/HAL_spi_Stm32f1.cpp +++ b/Marlin/src/HAL/HAL_STM32F1/HAL_spi_Stm32f1.cpp @@ -32,34 +32,25 @@ #ifdef __STM32F1__ -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - #include "../../inc/MarlinConfig.h" #include - -// -------------------------------------------------------------------------- -// Public Variables -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- +// ------------------------ // Public functions -// -------------------------------------------------------------------------- +// ------------------------ #if ENABLED(SOFTWARE_SPI) - // -------------------------------------------------------------------------- + // ------------------------ // Software SPI - // -------------------------------------------------------------------------- + // ------------------------ #error "Software SPI not supported for STM32F1. Use hardware SPI." #else -// -------------------------------------------------------------------------- +// ------------------------ // Hardware SPI -// -------------------------------------------------------------------------- +// ------------------------ /** * VGPV SPI speed start and F_CPU/2, by default 72/2 = 36Mhz @@ -88,15 +79,25 @@ void spiBegin() { * @details */ void spiInit(uint8_t spiRate) { + /** + * STM32F1 APB2 = 72MHz, APB1 = 36MHz, max SPI speed of this MCU if 18Mhz + * STM32F1 has 3 SPI ports, SPI1 in APB2, SPI2/SPI3 in APB1 + * so the minimum prescale of SPI1 is DIV4, SPI2/SPI3 is DIV2 + */ + #if SPI_DEVICE == 1 + #define SPI_CLOCK_MAX SPI_CLOCK_DIV4 + #else + #define SPI_CLOCK_MAX SPI_CLOCK_DIV2 + #endif uint8_t clock; switch (spiRate) { - case SPI_FULL_SPEED: clock = SPI_CLOCK_DIV2 ; break; + case SPI_FULL_SPEED: clock = SPI_CLOCK_MAX ; break; case SPI_HALF_SPEED: clock = SPI_CLOCK_DIV4 ; break; case SPI_QUARTER_SPEED: clock = SPI_CLOCK_DIV8 ; break; case SPI_EIGHTH_SPEED: clock = SPI_CLOCK_DIV16; break; case SPI_SPEED_5: clock = SPI_CLOCK_DIV32; break; case SPI_SPEED_6: clock = SPI_CLOCK_DIV64; break; - default: clock = SPI_CLOCK_DIV2; // Default from the SPI library + default: clock = SPI_CLOCK_DIV2; // Default from the SPI library } SPI.setModule(SPI_DEVICE); SPI.begin(); @@ -113,7 +114,7 @@ void spiInit(uint8_t spiRate) { * @details */ uint8_t spiRec(void) { - uint8_t returnByte = SPI.transfer(0xFF); + uint8_t returnByte = SPI.transfer(ff); return returnByte; } diff --git a/Marlin/src/HAL/HAL_STM32F1/HAL_timers_Stm32f1.cpp b/Marlin/src/HAL/HAL_STM32F1/HAL_timers_Stm32f1.cpp index e45c449876..faff842eb0 100644 --- a/Marlin/src/HAL/HAL_STM32F1/HAL_timers_Stm32f1.cpp +++ b/Marlin/src/HAL/HAL_STM32F1/HAL_timers_Stm32f1.cpp @@ -26,45 +26,17 @@ #ifdef __STM32F1__ -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - #include "HAL.h" #include "HAL_timers_STM32F1.h" -// -------------------------------------------------------------------------- -// Externals -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- +// ------------------------ // Local defines -// -------------------------------------------------------------------------- +// ------------------------ -// -------------------------------------------------------------------------- -// Types -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Public Variables -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Private Variables -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Function prototypes -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Private functions -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- +// ------------------------ // Public functions -// -------------------------------------------------------------------------- +// ------------------------ /** * Timer_clock1: Prescaler 2 -> 36 MHz @@ -85,7 +57,7 @@ void HAL_timer_start(const uint8_t timer_num, const uint32_t frequency) { case 3: irq_num = NVIC_TIMER3; break; case 4: irq_num = NVIC_TIMER4; break; case 5: irq_num = NVIC_TIMER5; break; - #ifdef STM32_HIGH_DENSITY + #if ENABLED(STM32_HIGH_DENSITY) // 6 & 7 are basic timers, avoid them case 8: irq_num = NVIC_TIMER8_CC; break; #endif @@ -110,7 +82,7 @@ void HAL_timer_start(const uint8_t timer_num, const uint32_t frequency) { timer_set_prescaler(STEP_TIMER_DEV, (uint16_t)(STEPPER_TIMER_PRESCALE - 1)); timer_set_reload(STEP_TIMER_DEV, 0xFFFF); timer_oc_set_mode(STEP_TIMER_DEV, STEP_TIMER_CHAN, TIMER_OC_MODE_FROZEN, TIMER_OC_NO_PRELOAD); // no output pin change - timer_set_compare(STEP_TIMER_DEV, STEP_TIMER_CHAN, MIN(hal_timer_t(HAL_TIMER_TYPE_MAX), (STEPPER_TIMER_RATE / frequency))); + timer_set_compare(STEP_TIMER_DEV, STEP_TIMER_CHAN, _MIN(hal_timer_t(HAL_TIMER_TYPE_MAX), (STEPPER_TIMER_RATE / frequency))); timer_no_ARR_preload_ARPE(STEP_TIMER_DEV); // Need to be sure no preload on ARR register timer_attach_interrupt(STEP_TIMER_DEV, STEP_TIMER_CHAN, stepTC_Handler); nvic_irq_set_priority(irq_num, STEP_TIMER_IRQ_PRIO); @@ -123,7 +95,7 @@ void HAL_timer_start(const uint8_t timer_num, const uint32_t frequency) { timer_set_count(TEMP_TIMER_DEV, 0); timer_set_prescaler(TEMP_TIMER_DEV, (uint16_t)(TEMP_TIMER_PRESCALE - 1)); timer_set_reload(TEMP_TIMER_DEV, 0xFFFF); - timer_set_compare(TEMP_TIMER_DEV, TEMP_TIMER_CHAN, MIN(hal_timer_t(HAL_TIMER_TYPE_MAX), ((F_CPU / TEMP_TIMER_PRESCALE) / frequency))); + timer_set_compare(TEMP_TIMER_DEV, TEMP_TIMER_CHAN, _MIN(hal_timer_t(HAL_TIMER_TYPE_MAX), ((F_CPU / TEMP_TIMER_PRESCALE) / frequency))); timer_attach_interrupt(TEMP_TIMER_DEV, TEMP_TIMER_CHAN, tempTC_Handler); nvic_irq_set_priority(irq_num, TEMP_TIMER_IRQ_PRIO); timer_generate_update(TEMP_TIMER_DEV); diff --git a/Marlin/src/HAL/HAL_STM32F1/HAL_timers_Stm32f1.h b/Marlin/src/HAL/HAL_STM32F1/HAL_timers_Stm32f1.h index 39241bcb8a..c114fe5ed4 100644 --- a/Marlin/src/HAL/HAL_STM32F1/HAL_timers_Stm32f1.h +++ b/Marlin/src/HAL/HAL_STM32F1/HAL_timers_Stm32f1.h @@ -25,16 +25,12 @@ * HAL for stm32duino.com based on Libmaple and compatible (STM32F1) */ -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - #include #include -// -------------------------------------------------------------------------- +// ------------------------ // Defines -// -------------------------------------------------------------------------- +// ------------------------ /** * TODO: Check and confirm what timer we will use for each Temps and stepper driving. @@ -96,21 +92,16 @@ timer_dev* get_timer_dev(int number); extern "C" void tempTC_Handler(void); extern "C" void stepTC_Handler(void); -// -------------------------------------------------------------------------- -// Types -// -------------------------------------------------------------------------- - - -// -------------------------------------------------------------------------- +// ------------------------ // Public Variables -// -------------------------------------------------------------------------- -/* -static HardwareTimer StepperTimer(STEP_TIMER_NUM); -static HardwareTimer TempTimer(TEMP_TIMER_NUM); -*/ -// -------------------------------------------------------------------------- +// ------------------------ + +//static HardwareTimer StepperTimer(STEP_TIMER_NUM); +//static HardwareTimer TempTimer(TEMP_TIMER_NUM); + +// ------------------------ // Public functions -// -------------------------------------------------------------------------- +// ------------------------ void HAL_timer_start(const uint8_t timer_num, const uint32_t frequency); void HAL_timer_enable_interrupt(const uint8_t timer_num); diff --git a/Marlin/src/HAL/HAL_STM32F1/u8g_com_stm32duino_fsmc.cpp b/Marlin/src/HAL/HAL_STM32F1/dogm/u8g_com_stm32duino_fsmc.cpp similarity index 73% rename from Marlin/src/HAL/HAL_STM32F1/u8g_com_stm32duino_fsmc.cpp rename to Marlin/src/HAL/HAL_STM32F1/dogm/u8g_com_stm32duino_fsmc.cpp index 4be4ae4dd4..35b10a2a5d 100644 --- a/Marlin/src/HAL/HAL_STM32F1/u8g_com_stm32duino_fsmc.cpp +++ b/Marlin/src/HAL/HAL_STM32F1/dogm/u8g_com_stm32duino_fsmc.cpp @@ -26,18 +26,21 @@ * Communication interface for FSMC */ -#include "../../inc/MarlinConfig.h" +#include "../../../inc/MarlinConfig.h" #if defined(ARDUINO_ARCH_STM32F1) && PIN_EXISTS(FSMC_CS) // FSMC on 100/144 pins SoCs #if HAS_GRAPHICAL_LCD -#include "U8glib.h" -#include "libmaple/fsmc.h" -#include "libmaple/gpio.h" -#include "boards.h" +#include +#include +#include +#include +#include -#define LCD_READ_ID 0x04 /* Read display identification information */ +#ifndef LCD_READ_ID + #define LCD_READ_ID 0x04 // Read display identification information (0xD3 on ILI9341) +#endif /* Timing configuration */ #define FSMC_ADDRESS_SETUP_TIME 15 // AddressSetupTime @@ -47,6 +50,10 @@ void LCD_IO_Init(uint8_t cs, uint8_t rs); void LCD_IO_WriteData(uint16_t RegValue); void LCD_IO_WriteReg(uint16_t Reg); uint32_t LCD_IO_ReadData(uint16_t RegValue, uint8_t ReadSize); +#ifdef LCD_USE_DMA_FSMC + void LCD_IO_WriteMultiple(uint16_t data, uint32_t count); + void LCD_IO_WriteSequence(uint16_t *data, uint16_t length); +#endif static uint8_t msgInitCount = 2; // Ignore all messages until 2nd U8G_COM_MSG_INIT @@ -59,21 +66,25 @@ uint8_t u8g_com_stm32duino_fsmc_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, voi static uint8_t isCommand; switch (msg) { - case U8G_COM_MSG_STOP: - break; + case U8G_COM_MSG_STOP: break; case U8G_COM_MSG_INIT: u8g_SetPIOutput(u8g, U8G_PI_RESET); + #ifdef LCD_USE_DMA_FSMC + dma_init(FSMC_DMA_DEV); + dma_disable(FSMC_DMA_DEV, FSMC_DMA_CHANNEL); + dma_set_priority(FSMC_DMA_DEV, FSMC_DMA_CHANNEL, DMA_PRIORITY_MEDIUM); + #endif + LCD_IO_Init(u8g->pin_list[U8G_PI_CS], u8g->pin_list[U8G_PI_A0]); - u8g_Delay(100); + u8g_Delay(50); - if (arg_ptr != nullptr) + if (arg_ptr) *((uint32_t *)arg_ptr) = LCD_IO_ReadData(LCD_READ_ID, 3); - isCommand = 0; break; - case U8G_COM_MSG_ADDRESS: // define cmd (arg_val = 0) or data mode (arg_val = 1) + case U8G_COM_MSG_ADDRESS: // define cmd (arg_val = 0) or data mode (arg_val = 1) isCommand = arg_val == 0 ? 1 : 0; break; @@ -89,7 +100,6 @@ uint8_t u8g_com_stm32duino_fsmc_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, voi break; case U8G_COM_MSG_WRITE_SEQ: - for (uint8_t i = 0; i < arg_val; i += 2) LCD_IO_WriteData(*(uint16_t *)(((uint32_t)arg_ptr) + i)); break; @@ -107,9 +117,9 @@ __attribute__((always_inline)) __STATIC_INLINE void __DSB(void) { __ASM volatile ("dsb 0xF":::"memory"); } -#define FSMC_CS_NE1 PD7 +#define FSMC_CS_NE1 PD7 -#ifdef STM32_XL_DENSITY +#if ENABLED(STM32_XL_DENSITY) #define FSMC_CS_NE2 PG9 #define FSMC_CS_NE3 PG10 #define FSMC_CS_NE4 PG12 @@ -141,7 +151,7 @@ __attribute__((always_inline)) __STATIC_INLINE void __DSB(void) { #define FSMC_RS_A22 PE6 #define FSMC_RS_A23 PE2 -#ifdef STM32_XL_DENSITY +#if ENABLED(STM32_XL_DENSITY) #define FSMC_RS_A24 PG13 #define FSMC_RS_A25 PG14 #endif @@ -163,7 +173,7 @@ void LCD_IO_Init(uint8_t cs, uint8_t rs) { switch (cs) { case FSMC_CS_NE1: controllerAddress = (uint32_t)FSMC_NOR_PSRAM_REGION1; break; - #ifdef STM32_XL_DENSITY + #if ENABLED(STM32_XL_DENSITY) case FSMC_CS_NE2: controllerAddress = (uint32_t)FSMC_NOR_PSRAM_REGION2; break; case FSMC_CS_NE3: controllerAddress = (uint32_t)FSMC_NOR_PSRAM_REGION3; break; case FSMC_CS_NE4: controllerAddress = (uint32_t)FSMC_NOR_PSRAM_REGION4; break; @@ -174,7 +184,7 @@ void LCD_IO_Init(uint8_t cs, uint8_t rs) { #define _ORADDR(N) controllerAddress |= (_BV32(N) - 2) switch (rs) { - #ifdef STM32_XL_DENSITY + #if ENABLED(STM32_XL_DENSITY) case FSMC_RS_A0: _ORADDR( 1); break; case FSMC_RS_A1: _ORADDR( 2); break; case FSMC_RS_A2: _ORADDR( 3); break; @@ -200,7 +210,7 @@ void LCD_IO_Init(uint8_t cs, uint8_t rs) { case FSMC_RS_A21: _ORADDR(22); break; case FSMC_RS_A22: _ORADDR(23); break; case FSMC_RS_A23: _ORADDR(24); break; - #ifdef STM32_XL_DENSITY + #if ENABLED(STM32_XL_DENSITY) case FSMC_RS_A24: _ORADDR(25); break; case FSMC_RS_A25: _ORADDR(26); break; #endif @@ -232,7 +242,7 @@ void LCD_IO_Init(uint8_t cs, uint8_t rs) { gpio_set_mode(PIN_MAP[cs].gpio_device, PIN_MAP[cs].gpio_bit, GPIO_AF_OUTPUT_PP); //FSMC_CS_NEx gpio_set_mode(PIN_MAP[rs].gpio_device, PIN_MAP[rs].gpio_bit, GPIO_AF_OUTPUT_PP); //FSMC_RS_Ax - #ifdef STM32_XL_DENSITY + #if ENABLED(STM32_XL_DENSITY) FSMC_NOR_PSRAM4_BASE->BCR = FSMC_BCR_WREN | FSMC_BCR_MTYP_SRAM | FSMC_BCR_MWID_16BITS | FSMC_BCR_MBKEN; FSMC_NOR_PSRAM4_BASE->BTR = (FSMC_DATA_SETUP_TIME << 8) | FSMC_ADDRESS_SETUP_TIME; #else // PSRAM1 for STM32F103V (high density) @@ -257,7 +267,7 @@ void LCD_IO_WriteReg(uint16_t Reg) { uint32_t LCD_IO_ReadData(uint16_t RegValue, uint8_t ReadSize) { volatile uint32_t data; - LCD->REG = (uint16_t)RegValue; + LCD->REG = RegValue; __DSB(); data = LCD->RAM; // dummy read @@ -267,9 +277,48 @@ uint32_t LCD_IO_ReadData(uint16_t RegValue, uint8_t ReadSize) { data <<= 8; data |= (LCD->RAM & 0x00FF); } - return (uint32_t)data; + return uint32_t(data); } -#endif // HAS_GRAPHICAL_LCD +#if ENABLED(LCD_USE_DMA_FSMC) +void LCD_IO_WriteMultiple(uint16_t color, uint32_t count) { + while (count > 0) { + dma_setup_transfer(FSMC_DMA_DEV, FSMC_DMA_CHANNEL, &color, DMA_SIZE_16BITS, &LCD->RAM, DMA_SIZE_16BITS, DMA_MEM_2_MEM); + dma_set_num_transfers(FSMC_DMA_DEV, FSMC_DMA_CHANNEL, count > 65535 ? 65535 : count); + dma_clear_isr_bits(FSMC_DMA_DEV, FSMC_DMA_CHANNEL); + dma_enable(FSMC_DMA_DEV, FSMC_DMA_CHANNEL); + + while ((dma_get_isr_bits(FSMC_DMA_DEV, FSMC_DMA_CHANNEL) & 0x0A) == 0) {}; + dma_disable(FSMC_DMA_DEV, FSMC_DMA_CHANNEL); + + count = count > 65535 ? count - 65535 : 0; + } +} + +void LCD_IO_WriteSequence(uint16_t *data, uint16_t length) { + dma_setup_transfer(FSMC_DMA_DEV, FSMC_DMA_CHANNEL, data, DMA_SIZE_16BITS, &LCD->RAM, DMA_SIZE_16BITS, DMA_MEM_2_MEM | DMA_PINC_MODE); + dma_set_num_transfers(FSMC_DMA_DEV, FSMC_DMA_CHANNEL, length); + dma_clear_isr_bits(FSMC_DMA_DEV, FSMC_DMA_CHANNEL); + dma_enable(FSMC_DMA_DEV, FSMC_DMA_CHANNEL); + + while ((dma_get_isr_bits(FSMC_DMA_DEV, FSMC_DMA_CHANNEL) & 0x0A) == 0) {}; + dma_disable(FSMC_DMA_DEV, FSMC_DMA_CHANNEL); +} + +void LCD_IO_WriteSequence_Async(uint16_t *data, uint16_t length) { + dma_setup_transfer(FSMC_DMA_DEV, FSMC_DMA_CHANNEL, data, DMA_SIZE_16BITS, &LCD->RAM, DMA_SIZE_16BITS, DMA_MEM_2_MEM | DMA_PINC_MODE); + dma_set_num_transfers(FSMC_DMA_DEV, FSMC_DMA_CHANNEL, length); + dma_clear_isr_bits(FSMC_DMA_DEV, FSMC_DMA_CHANNEL); + dma_enable(FSMC_DMA_DEV, FSMC_DMA_CHANNEL); +} + +void LCD_IO_WaitSequence_Async() { + while ((dma_get_isr_bits(FSMC_DMA_DEV, FSMC_DMA_CHANNEL) & 0x0A) == 0) {}; + dma_disable(FSMC_DMA_DEV, FSMC_DMA_CHANNEL); +} + +#endif // LCD_USE_DMA_FSMC + +#endif // HAS_GRAPHICAL_LCD #endif // ARDUINO_ARCH_STM32F1 && FSMC_CS_PIN diff --git a/Marlin/src/HAL/HAL_STM32F1/u8g_com_stm32duino_swspi.cpp b/Marlin/src/HAL/HAL_STM32F1/dogm/u8g_com_stm32duino_swspi.cpp similarity index 98% rename from Marlin/src/HAL/HAL_STM32F1/u8g_com_stm32duino_swspi.cpp rename to Marlin/src/HAL/HAL_STM32F1/dogm/u8g_com_stm32duino_swspi.cpp index 51d1fac9d4..753a5d5e70 100644 --- a/Marlin/src/HAL/HAL_STM32F1/u8g_com_stm32duino_swspi.cpp +++ b/Marlin/src/HAL/HAL_STM32F1/dogm/u8g_com_stm32duino_swspi.cpp @@ -18,11 +18,11 @@ */ #ifdef __STM32F1__ -#include "../../inc/MarlinConfig.h" +#include "../../../inc/MarlinConfig.h" #if HAS_GRAPHICAL_LCD && ENABLED(FORCE_SOFT_SPI) -#include "HAL.h" +#include "../HAL.h" #include #undef SPI_SPEED diff --git a/Marlin/src/HAL/HAL_STM32F1/fastio_Stm32f1.h b/Marlin/src/HAL/HAL_STM32F1/fastio_Stm32f1.h index fe09de3ebb..6cc7a72d95 100644 --- a/Marlin/src/HAL/HAL_STM32F1/fastio_Stm32f1.h +++ b/Marlin/src/HAL/HAL_STM32F1/fastio_Stm32f1.h @@ -56,3 +56,130 @@ #define extDigitalRead(IO) digitalRead(IO) #define extDigitalWrite(IO,V) digitalWrite(IO,V) +// +// Pins Definitions +// +#define PA0 0x00 +#define PA1 0x01 +#define PA2 0x02 +#define PA3 0x03 +#define PA4 0x04 +#define PA5 0x05 +#define PA6 0x06 +#define PA7 0x07 +#define PA8 0x08 +#define PA9 0x09 +#define PA10 0x0A +#define PA11 0x0B +#define PA12 0x0C +#define PA13 0x0D +#define PA14 0x0E +#define PA15 0x0F + +#define PB0 0x10 +#define PB1 0x11 +#define PB2 0x12 +#define PB3 0x13 +#define PB4 0x14 +#define PB5 0x15 +#define PB6 0x16 +#define PB7 0x17 // 36 pins (F103T) +#define PB8 0x18 +#define PB9 0x19 +#define PB10 0x1A +#define PB11 0x1B +#define PB12 0x1C +#define PB13 0x1D +#define PB14 0x1E +#define PB15 0x1F + +#if defined(MCU_STM32F103CB) || defined(MCU_STM32F103C8) + #define PC13 0x20 + #define PC14 0x21 + #define PC15 0x22 +#else + #define PC0 0x20 + #define PC1 0x21 + #define PC2 0x22 + #define PC3 0x23 + #define PC4 0x24 + #define PC5 0x25 + #define PC6 0x26 + #define PC7 0x27 + #define PC8 0x28 + #define PC9 0x29 + #define PC10 0x2A + #define PC11 0x2B + #define PC12 0x2C + #define PC13 0x2D + #define PC14 0x2E + #define PC15 0x2F +#endif + +#define PD0 0x30 +#define PD1 0x31 +#define PD2 0x32 // 64 pins (F103R) +#define PD3 0x33 +#define PD4 0x34 +#define PD5 0x35 +#define PD6 0x36 +#define PD7 0x37 +#define PD8 0x38 +#define PD9 0x39 +#define PD10 0x3A +#define PD11 0x3B +#define PD12 0x3C +#define PD13 0x3D +#define PD14 0x3E +#define PD15 0x3F + +#define PE0 0x40 +#define PE1 0x41 +#define PE2 0x42 +#define PE3 0x43 +#define PE4 0x44 +#define PE5 0x45 +#define PE6 0x46 +#define PE7 0x47 +#define PE8 0x48 +#define PE9 0x49 +#define PE10 0x4A +#define PE11 0x4B +#define PE12 0x4C +#define PE13 0x4D +#define PE14 0x4E +#define PE15 0x4F // 100 pins (F103V) + +#define PF0 0x50 +#define PF1 0x51 +#define PF2 0x52 +#define PF3 0x53 +#define PF4 0x54 +#define PF5 0x55 +#define PF6 0x56 +#define PF7 0x57 +#define PF8 0x58 +#define PF9 0x59 +#define PF10 0x5A +#define PF11 0x5B +#define PF12 0x5C +#define PF13 0x5D +#define PF14 0x5E +#define PF15 0x5F + +#define PG0 0x60 +#define PG1 0x61 +#define PG2 0x62 +#define PG3 0x63 +#define PG4 0x64 +#define PG5 0x65 +#define PG6 0x66 +#define PG7 0x67 +#define PG8 0x68 +#define PG9 0x69 +#define PG10 0x6A +#define PG11 0x6B +#define PG12 0x6C +#define PG13 0x6D +#define PG14 0x6E +#define PG15 0x6F // 144 pins (F103Z) diff --git a/Marlin/src/HAL/HAL_STM32F1/inc/Conditionals_LCD.h b/Marlin/src/HAL/HAL_STM32F1/inc/Conditionals_LCD.h new file mode 100644 index 0000000000..85f26f4016 --- /dev/null +++ b/Marlin/src/HAL/HAL_STM32F1/inc/Conditionals_LCD.h @@ -0,0 +1,22 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once diff --git a/Marlin/src/HAL/HAL_STM32F1/inc/Conditionals_adv.h b/Marlin/src/HAL/HAL_STM32F1/inc/Conditionals_adv.h new file mode 100644 index 0000000000..85f26f4016 --- /dev/null +++ b/Marlin/src/HAL/HAL_STM32F1/inc/Conditionals_adv.h @@ -0,0 +1,22 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once diff --git a/Marlin/src/HAL/HAL_STM32F1/inc/Conditionals_post.h b/Marlin/src/HAL/HAL_STM32F1/inc/Conditionals_post.h new file mode 100644 index 0000000000..85f26f4016 --- /dev/null +++ b/Marlin/src/HAL/HAL_STM32F1/inc/Conditionals_post.h @@ -0,0 +1,22 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once diff --git a/Marlin/src/HAL/HAL_STM32F1/SanityCheck.h b/Marlin/src/HAL/HAL_STM32F1/inc/SanityCheck.h similarity index 100% rename from Marlin/src/HAL/HAL_STM32F1/SanityCheck.h rename to Marlin/src/HAL/HAL_STM32F1/inc/SanityCheck.h diff --git a/Marlin/src/HAL/HAL_STM32F1/persistent_store_eeprom.cpp b/Marlin/src/HAL/HAL_STM32F1/persistent_store_eeprom.cpp index b4ef57e1da..b1b50a39e1 100644 --- a/Marlin/src/HAL/HAL_STM32F1/persistent_store_eeprom.cpp +++ b/Marlin/src/HAL/HAL_STM32F1/persistent_store_eeprom.cpp @@ -49,10 +49,10 @@ bool PersistentStore::write_data(int &pos, const uint8_t *value, size_t size, ui return false; } -bool PersistentStore::read_data(int &pos, uint8_t* value, size_t size, uint16_t *crc, const bool set/*=true*/) { +bool PersistentStore::read_data(int &pos, uint8_t* value, size_t size, uint16_t *crc, const bool writing/*=true*/) { do { uint8_t c = eeprom_read_byte((uint8_t*)pos); - if (set && value) *value = c; + if (writing && value) *value = c; crc16(crc, &c, 1); pos++; value++; diff --git a/Marlin/src/HAL/HAL_STM32F1/persistent_store_flash.cpp b/Marlin/src/HAL/HAL_STM32F1/persistent_store_flash.cpp index 4e73d0564e..7004d88ffd 100644 --- a/Marlin/src/HAL/HAL_STM32F1/persistent_store_flash.cpp +++ b/Marlin/src/HAL/HAL_STM32F1/persistent_store_flash.cpp @@ -55,7 +55,7 @@ bool PersistentStore::access_finish() { return true; } -bool PersistentStore::write_data(int &pos, const uint8_t *value, const size_t size, uint16_t *crc) { +bool PersistentStore::write_data(int &pos, const uint8_t *value, size_t size, uint16_t *crc) { FLASH_Status status; if (firstWrite) { diff --git a/Marlin/src/HAL/HAL_STM32F1/persistent_store_sdcard.cpp b/Marlin/src/HAL/HAL_STM32F1/persistent_store_sdcard.cpp index 3244093577..61391fda2b 100644 --- a/Marlin/src/HAL/HAL_STM32F1/persistent_store_sdcard.cpp +++ b/Marlin/src/HAL/HAL_STM32F1/persistent_store_sdcard.cpp @@ -22,6 +22,7 @@ /** * HAL for stm32duino.com based on Libmaple and compatible (STM32F1) + * Implementation of EEPROM settings in SD Card */ #ifdef __STM32F1__ @@ -33,11 +34,12 @@ #include "../shared/persistent_store_api.h" #ifndef E2END - #define E2END 4095 + #define E2END 0xFFF // 4KB #endif -#define HAL_STM32F1_EEPROM_SIZE (E2END + 1) +#define HAL_EEPROM_SIZE (E2END + 1) -static char HAL_STM32F1_eeprom_content[HAL_STM32F1_EEPROM_SIZE]; +#define _ALIGN(x) __attribute__ ((aligned(x))) // SDIO uint32_t* compat. +static char _ALIGN(4) HAL_eeprom_data[HAL_EEPROM_SIZE]; #if ENABLED(SDSUPPORT) @@ -52,10 +54,10 @@ static char HAL_STM32F1_eeprom_content[HAL_STM32F1_EEPROM_SIZE]; if (!file.open(&root, EEPROM_FILENAME, O_RDONLY)) return false; - int16_t bytes_read = file.read(HAL_STM32F1_eeprom_content, HAL_STM32F1_EEPROM_SIZE); + int bytes_read = file.read(HAL_eeprom_data, HAL_EEPROM_SIZE); if (bytes_read < 0) return false; - for (; bytes_read < HAL_STM32F1_EEPROM_SIZE; bytes_read++) - HAL_STM32F1_eeprom_content[bytes_read] = 0xFF; + for (; bytes_read < HAL_EEPROM_SIZE; bytes_read++) + HAL_eeprom_data[bytes_read] = 0xFF; file.close(); return true; } @@ -64,12 +66,12 @@ static char HAL_STM32F1_eeprom_content[HAL_STM32F1_EEPROM_SIZE]; if (!card.isDetected()) return false; SdFile file, root = card.getroot(); - int16_t bytes_written = 0; + int bytes_written = 0; if (file.open(&root, EEPROM_FILENAME, O_CREAT | O_WRITE | O_TRUNC)) { - bytes_written = file.write(HAL_STM32F1_eeprom_content, HAL_STM32F1_EEPROM_SIZE); + bytes_written = file.write(HAL_eeprom_data, HAL_EEPROM_SIZE); file.close(); } - return (bytes_written == HAL_STM32F1_EEPROM_SIZE); + return (bytes_written == HAL_EEPROM_SIZE); } #else // !SDSUPPORT @@ -78,9 +80,9 @@ static char HAL_STM32F1_eeprom_content[HAL_STM32F1_EEPROM_SIZE]; #endif // !SDSUPPORT -bool PersistentStore::write_data(int &pos, const uint8_t *value, const size_t size, uint16_t *crc) { +bool PersistentStore::write_data(int &pos, const uint8_t *value, size_t size, uint16_t *crc) { for (size_t i = 0; i < size; i++) - HAL_STM32F1_eeprom_content[pos + i] = value[i]; + HAL_eeprom_data[pos + i] = value[i]; crc16(crc, value, size); pos += size; return false; @@ -88,7 +90,7 @@ bool PersistentStore::write_data(int &pos, const uint8_t *value, const size_t si bool PersistentStore::read_data(int &pos, uint8_t* value, const size_t size, uint16_t *crc, const bool writing/*=true*/) { for (size_t i = 0; i < size; i++) { - uint8_t c = HAL_STM32F1_eeprom_content[pos + i]; + uint8_t c = HAL_eeprom_data[pos + i]; if (writing) value[i] = c; crc16(crc, &c, 1); } @@ -96,7 +98,7 @@ bool PersistentStore::read_data(int &pos, uint8_t* value, const size_t size, uin return false; } -size_t PersistentStore::capacity() { return HAL_STM32F1_EEPROM_SIZE; } +size_t PersistentStore::capacity() { return HAL_EEPROM_SIZE; } #endif // EEPROM_SETTINGS diff --git a/Marlin/src/HAL/HAL_STM32F1/pinsDebug.h b/Marlin/src/HAL/HAL_STM32F1/pinsDebug.h index b7f75343a2..a8b632870a 100644 --- a/Marlin/src/HAL/HAL_STM32F1/pinsDebug.h +++ b/Marlin/src/HAL/HAL_STM32F1/pinsDebug.h @@ -16,112 +16,12 @@ * along with this program. If not, see . * */ +#pragma once -/** - * Support routines for STM32F1 - */ -#ifdef __STM32F1__ - -/** - * Translation of routines & variables used by pinsDebug.h - */ -#include "fastio_STM32F1.h" - -extern const stm32_pin_info PIN_MAP[BOARD_NR_GPIO_PINS]; - -#define NUM_DIGITAL_PINS BOARD_NR_GPIO_PINS -#define NUMBER_PINS_TOTAL BOARD_NR_GPIO_PINS -#define VALID_PIN(pin) (pin >= 0 && pin < BOARD_NR_GPIO_PINS) -#define GET_ARRAY_PIN(p) pin_t(pin_array[p].pin) -#define pwm_status(pin) PWM_PIN(pin) -#define digitalRead_mod(p) extDigitalRead(p) -#define NAME_FORMAT(p) PSTR("%-##p##s") -#define PRINT_PIN(p) do{ sprintf_P(buffer, PSTR("%3hd "), int16_t(p)); SERIAL_ECHO(buffer); }while(0) -#define PRINT_PORT(p) print_port(p) -#define PRINT_ARRAY_NAME(x) do {sprintf_P(buffer, PSTR("%-" STRINGIFY(MAX_NAME_LENGTH) "s"), pin_array[x].name); SERIAL_ECHO(buffer);} while (0) -#define MULTI_NAME_PAD 20 // spaces needed to be pretty if not first name assigned to a pin - -// pins that will cause hang/reset/disconnect in M43 Toggle and Watch utilities -#ifndef M43_NEVER_TOUCH - #define M43_NEVER_TOUCH(Q) (Q >= 9 && Q <= 12) // SERIAL/USB pins PA9(TX) PA10(RX) +#ifdef NUM_DIGITAL_PINS // Only in ST's Arduino core (STM32duino, STM32Core) + #include "../HAL_STM32/pinsDebug_STM32duino.h" +#elif defined(BOARD_NR_GPIO_PINS) // Only in STM32GENERIC (Maple) + #include "../HAL_STM32/pinsDebug_STM32GENERIC.h" +#else + #error "M43 not supported for this board" #endif - -static inline int8_t get_pin_mode(pin_t pin) { - return VALID_PIN(pin) ? _GET_MODE(pin) : -1; -} - -static inline pin_t DIGITAL_PIN_TO_ANALOG_PIN(pin_t pin) { - if (!VALID_PIN(pin)) return -1; - int8_t adc_channel = int8_t(PIN_MAP[pin].adc_channel); - #ifdef NUM_ANALOG_INPUTS - if (adc_channel >= NUM_ANALOG_INPUTS) adc_channel = ADCx; - #endif - return pin_t(adc_channel); -} - -static inline bool IS_ANALOG(pin_t pin) { - if (!VALID_PIN(pin)) return false; - if (PIN_MAP[pin].adc_channel != ADCx) { - #ifdef NUM_ANALOG_INPUTS - if (PIN_MAP[pin].adc_channel >= NUM_ANALOG_INPUTS) return false; - #endif - return _GET_MODE(pin) == GPIO_INPUT_ANALOG && !M43_NEVER_TOUCH(pin); - } - return false; -} - -static inline bool GET_PINMODE(pin_t pin) { - return VALID_PIN(pin) ? !IS_INPUT(pin) : false; -} - -static inline bool GET_ARRAY_IS_DIGITAL(int16_t array_pin) { - pin_t pin = GET_ARRAY_PIN(array_pin); - bool isDigital = !IS_ANALOG(pin); - #ifdef NUM_ANALOG_INPUTS - if (!isDigital && PIN_MAP[pin].adc_channel >= NUM_ANALOG_INPUTS) - isDigital = true; - #endif - return isDigital; -} - -static inline void pwm_details(pin_t pin) { - if (PWM_PIN(pin)) { - char buffer[16], num = '?'; - timer_dev * const tdev = PIN_MAP[pin].timer_device; - const uint8_t channel = PIN_MAP[pin].timer_channel; - if (tdev == &timer1) num = '1'; - else if (tdev == &timer1) num = '1'; - else if (tdev == &timer2) num = '2'; - else if (tdev == &timer3) num = '3'; - else if (tdev == &timer4) num = '4'; - #ifdef STM32_HIGH_DENSITY - else if (tdev == &timer5) num = '5'; - else if (tdev == &timer8) num = '8'; - #endif - sprintf_P(buffer, PSTR(" TIM%c CH%c"), num, ('0' + channel)); - SERIAL_ECHO(buffer); - } -} - -static inline void print_port(pin_t pin) { - char buffer[8]; - char port = 'A' + char(pin >> 4); // pin div 16 - /* seems not to be required for our devices - gpio_dev* gp = PIN_MAP[pin].gpio_device; - if (gp == &gpioa) port = 'A'; - else if (gp == &gpiob) port = 'B'; - else if (gp == &gpioc) port = 'C'; - else if (gp == &gpiod) port = 'D'; - #if STM32_NR_GPIO_PORTS > 4 - else if (gp == &gpioe) port = 'E'; - else if (gp == &gpiof) port = 'F'; - else if (gp == &gpiog) port = 'G'; - #endif - */ - const int16_t gbit = PIN_MAP[pin].gpio_bit; - sprintf_P(buffer, PSTR("P%c%hd "), port, gbit); - if (gbit < 10) SERIAL_CHAR(' '); - SERIAL_ECHO(buffer); -} - -#endif // __STM32F1__ diff --git a/Marlin/src/HAL/HAL_STM32F1/stm32f1_flag_script.py b/Marlin/src/HAL/HAL_STM32F1/stm32f1_flag_script.py index 5bb2f18fb6..6310740fe0 100644 --- a/Marlin/src/HAL/HAL_STM32F1/stm32f1_flag_script.py +++ b/Marlin/src/HAL/HAL_STM32F1/stm32f1_flag_script.py @@ -4,7 +4,6 @@ import sys #dynamic build flags for generic compile options if __name__ == "__main__": args = " ".join([ "-std=gnu11", - "-std=gnu++11", "-Os", "-mcpu=cortex-m3", "-mthumb", diff --git a/Marlin/src/HAL/HAL_STM32F1/watchdog_Stm32f1.cpp b/Marlin/src/HAL/HAL_STM32F1/watchdog_Stm32f1.cpp index 69dca32680..62e4d077eb 100644 --- a/Marlin/src/HAL/HAL_STM32F1/watchdog_Stm32f1.cpp +++ b/Marlin/src/HAL/HAL_STM32F1/watchdog_Stm32f1.cpp @@ -56,5 +56,4 @@ void watchdog_init(void) { } #endif // USE_WATCHDOG - #endif // __STM32F1__ diff --git a/Marlin/src/HAL/HAL_STM32F4/EEPROM_Emul/eeprom_emul.cpp b/Marlin/src/HAL/HAL_STM32F4/EEPROM_Emul/eeprom_emul.cpp deleted file mode 100644 index 8bae46777d..0000000000 --- a/Marlin/src/HAL/HAL_STM32F4/EEPROM_Emul/eeprom_emul.cpp +++ /dev/null @@ -1,569 +0,0 @@ -/** - ****************************************************************************** - * @file EEPROM/EEPROM_Emulation/src/eeprom.c - * @author MCD Application Team - * @version V1.2.6 - * @date 04-November-2016 - * @brief This file provides all the EEPROM emulation firmware functions. - ****************************************************************************** - * @attention - * - *

© Copyright © 2016 STMicroelectronics International N.V. - * All rights reserved.

- * - * Redistribution and use in source and binary forms, with or without - * modification, are permitted, provided that the following conditions are met: - * - * 1. Redistribution of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of other - * contributors to this software may be used to endorse or promote products - * derived from this software without specific written permission. - * 4. This software, including modifications and/or derivative works of this - * software, must execute solely and exclusively on microcontroller or - * microprocessor devices manufactured by or for STMicroelectronics. - * 5. Redistribution and use of this software other than as permitted under - * this license is void and will automatically terminate your rights under - * this license. - * - * THIS SOFTWARE IS PROVIDED BY STMICROELECTRONICS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS, IMPLIED OR STATUTORY WARRANTIES, INCLUDING, BUT NOT - * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A - * PARTICULAR PURPOSE AND NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY - * RIGHTS ARE DISCLAIMED TO THE FULLEST EXTENT PERMITTED BY LAW. IN NO EVENT - * SHALL STMICROELECTRONICS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, - * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT - * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, - * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF - * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING - * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, - * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - ****************************************************************************** - */ -/** @addtogroup EEPROM_Emulation - * @{ - */ -#if defined(STM32GENERIC) && (defined(STM32F4)) - -/* Includes ------------------------------------------------------------------*/ -#include "eeprom_emul.h" - -/* Private typedef -----------------------------------------------------------*/ -/* Private define ------------------------------------------------------------*/ -/* Private macro -------------------------------------------------------------*/ -/* Private variables ---------------------------------------------------------*/ - -/* Global variable used to store variable value in read sequence */ -uint16_t DataVar = 0; - -/* Virtual address defined by the user: 0xFFFF value is prohibited */ -uint16_t VirtAddVarTab[NB_OF_VAR]; - -/* Private function prototypes -----------------------------------------------*/ -/* Private functions ---------------------------------------------------------*/ -static HAL_StatusTypeDef EE_Format(void); -static uint16_t EE_FindValidPage(uint8_t Operation); -static uint16_t EE_VerifyPageFullWriteVariable(uint16_t VirtAddress, uint16_t Data); -static uint16_t EE_PageTransfer(uint16_t VirtAddress, uint16_t Data); -static uint16_t EE_VerifyPageFullyErased(uint32_t Address); - -/** - * @brief Restore the pages to a known good state in case of page's status - * corruption after a power loss. - * @param None. - * @retval - Flash error code: on write Flash error - * - FLASH_COMPLETE: on success - */ -uint16_t EE_Initialize(void) { - uint16_t PageStatus0 = 6, PageStatus1 = 6; - uint16_t VarIdx = 0; - uint16_t EepromStatus = 0, ReadStatus = 0; - int16_t x = -1; - HAL_StatusTypeDef FlashStatus; - uint32_t SectorError = 0; - FLASH_EraseInitTypeDef pEraseInit; - - - /* Get Page0 status */ - PageStatus0 = (*(__IO uint16_t*)PAGE0_BASE_ADDRESS); - /* Get Page1 status */ - PageStatus1 = (*(__IO uint16_t*)PAGE1_BASE_ADDRESS); - - pEraseInit.TypeErase = TYPEERASE_SECTORS; - pEraseInit.Sector = PAGE0_ID; - pEraseInit.NbSectors = 1; - pEraseInit.VoltageRange = VOLTAGE_RANGE; - - /* Check for invalid header states and repair if necessary */ - switch (PageStatus0) { - case ERASED: - if (PageStatus1 == VALID_PAGE) { /* Page0 erased, Page1 valid */ - /* Erase Page0 */ - if (!EE_VerifyPageFullyErased(PAGE0_BASE_ADDRESS)) { - FlashStatus = HAL_FLASHEx_Erase(&pEraseInit, &SectorError); - /* If erase operation was failed, a Flash error code is returned */ - if (FlashStatus != HAL_OK) return FlashStatus; - } - } - else if (PageStatus1 == RECEIVE_DATA) { /* Page0 erased, Page1 receive */ - /* Erase Page0 */ - if (!EE_VerifyPageFullyErased(PAGE0_BASE_ADDRESS)) { - FlashStatus = HAL_FLASHEx_Erase(&pEraseInit, &SectorError); - /* If erase operation was failed, a Flash error code is returned */ - if (FlashStatus != HAL_OK) return FlashStatus; - } - /* Mark Page1 as valid */ - FlashStatus = HAL_FLASH_Program(TYPEPROGRAM_HALFWORD, PAGE1_BASE_ADDRESS, VALID_PAGE); - /* If program operation was failed, a Flash error code is returned */ - if (FlashStatus != HAL_OK) return FlashStatus; - } - else { /* First EEPROM access (Page0&1 are erased) or invalid state -> format EEPROM */ - /* Erase both Page0 and Page1 and set Page0 as valid page */ - FlashStatus = EE_Format(); - /* If erase/program operation was failed, a Flash error code is returned */ - if (FlashStatus != HAL_OK) return FlashStatus; - } - break; - - case RECEIVE_DATA: - if (PageStatus1 == VALID_PAGE) { /* Page0 receive, Page1 valid */ - /* Transfer data from Page1 to Page0 */ - for (VarIdx = 0; VarIdx < NB_OF_VAR; VarIdx++) { - if (( *(__IO uint16_t*)(PAGE0_BASE_ADDRESS + 6)) == VirtAddVarTab[VarIdx]) - x = VarIdx; - if (VarIdx != x) { - /* Read the last variables' updates */ - ReadStatus = EE_ReadVariable(VirtAddVarTab[VarIdx], &DataVar); - /* In case variable corresponding to the virtual address was found */ - if (ReadStatus != 0x1) { - /* Transfer the variable to the Page0 */ - EepromStatus = EE_VerifyPageFullWriteVariable(VirtAddVarTab[VarIdx], DataVar); - /* If program operation was failed, a Flash error code is returned */ - if (EepromStatus != HAL_OK) return EepromStatus; - } - } - } - /* Mark Page0 as valid */ - FlashStatus = HAL_FLASH_Program(TYPEPROGRAM_HALFWORD, PAGE0_BASE_ADDRESS, VALID_PAGE); - /* If program operation was failed, a Flash error code is returned */ - if (FlashStatus != HAL_OK) return FlashStatus; - pEraseInit.Sector = PAGE1_ID; - pEraseInit.NbSectors = 1; - pEraseInit.VoltageRange = VOLTAGE_RANGE; - /* Erase Page1 */ - if (!EE_VerifyPageFullyErased(PAGE1_BASE_ADDRESS)) { - FlashStatus = HAL_FLASHEx_Erase(&pEraseInit, &SectorError); - /* If erase operation was failed, a Flash error code is returned */ - if (FlashStatus != HAL_OK) return FlashStatus; - } - } - else if (PageStatus1 == ERASED) { /* Page0 receive, Page1 erased */ - pEraseInit.Sector = PAGE1_ID; - pEraseInit.NbSectors = 1; - pEraseInit.VoltageRange = VOLTAGE_RANGE; - /* Erase Page1 */ - if (!EE_VerifyPageFullyErased(PAGE1_BASE_ADDRESS)) { - FlashStatus = HAL_FLASHEx_Erase(&pEraseInit, &SectorError); - /* If erase operation was failed, a Flash error code is returned */ - if (FlashStatus != HAL_OK) return FlashStatus; - } - /* Mark Page0 as valid */ - FlashStatus = HAL_FLASH_Program(TYPEPROGRAM_HALFWORD, PAGE0_BASE_ADDRESS, VALID_PAGE); - /* If program operation was failed, a Flash error code is returned */ - if (FlashStatus != HAL_OK) return FlashStatus; - } - else { /* Invalid state -> format eeprom */ - /* Erase both Page0 and Page1 and set Page0 as valid page */ - FlashStatus = EE_Format(); - /* If erase/program operation was failed, a Flash error code is returned */ - if (FlashStatus != HAL_OK) return FlashStatus; - } - break; - - case VALID_PAGE: - if (PageStatus1 == VALID_PAGE) { /* Invalid state -> format eeprom */ - /* Erase both Page0 and Page1 and set Page0 as valid page */ - FlashStatus = EE_Format(); - /* If erase/program operation was failed, a Flash error code is returned */ - if (FlashStatus != HAL_OK) return FlashStatus; - } - else if (PageStatus1 == ERASED) { /* Page0 valid, Page1 erased */ - pEraseInit.Sector = PAGE1_ID; - pEraseInit.NbSectors = 1; - pEraseInit.VoltageRange = VOLTAGE_RANGE; - /* Erase Page1 */ - if (!EE_VerifyPageFullyErased(PAGE1_BASE_ADDRESS)) { - FlashStatus = HAL_FLASHEx_Erase(&pEraseInit, &SectorError); - /* If erase operation was failed, a Flash error code is returned */ - if (FlashStatus != HAL_OK) return FlashStatus; - } - } - else { /* Page0 valid, Page1 receive */ - /* Transfer data from Page0 to Page1 */ - for (VarIdx = 0; VarIdx < NB_OF_VAR; VarIdx++) { - if ((*(__IO uint16_t*)(PAGE1_BASE_ADDRESS + 6)) == VirtAddVarTab[VarIdx]) - x = VarIdx; - - if (VarIdx != x) { - /* Read the last variables' updates */ - ReadStatus = EE_ReadVariable(VirtAddVarTab[VarIdx], &DataVar); - /* In case variable corresponding to the virtual address was found */ - if (ReadStatus != 0x1) { - /* Transfer the variable to the Page1 */ - EepromStatus = EE_VerifyPageFullWriteVariable(VirtAddVarTab[VarIdx], DataVar); - /* If program operation was failed, a Flash error code is returned */ - if (EepromStatus != HAL_OK) return EepromStatus; - } - } - } - /* Mark Page1 as valid */ - FlashStatus = HAL_FLASH_Program(TYPEPROGRAM_HALFWORD, PAGE1_BASE_ADDRESS, VALID_PAGE); - /* If program operation was failed, a Flash error code is returned */ - if (FlashStatus != HAL_OK) return FlashStatus; - pEraseInit.Sector = PAGE0_ID; - pEraseInit.NbSectors = 1; - pEraseInit.VoltageRange = VOLTAGE_RANGE; - /* Erase Page0 */ - if (!EE_VerifyPageFullyErased(PAGE0_BASE_ADDRESS)) { - FlashStatus = HAL_FLASHEx_Erase(&pEraseInit, &SectorError); - /* If erase operation was failed, a Flash error code is returned */ - if (FlashStatus != HAL_OK) return FlashStatus; - } - } - break; - - default: /* Any other state -> format eeprom */ - /* Erase both Page0 and Page1 and set Page0 as valid page */ - FlashStatus = EE_Format(); - /* If erase/program operation was failed, a Flash error code is returned */ - if (FlashStatus != HAL_OK) return FlashStatus; - break; - } - - return HAL_OK; -} - -/** - * @brief Verify if specified page is fully erased. - * @param Address: page address - * This parameter can be one of the following values: - * @arg PAGE0_BASE_ADDRESS: Page0 base address - * @arg PAGE1_BASE_ADDRESS: Page1 base address - * @retval page fully erased status: - * - 0: if Page not erased - * - 1: if Page erased - */ -uint16_t EE_VerifyPageFullyErased(uint32_t Address) { - uint32_t ReadStatus = 1; - uint16_t AddressValue = 0x5555; - /* Check each active page address starting from end */ - while (Address <= PAGE0_END_ADDRESS) { - /* Get the current location content to be compared with virtual address */ - AddressValue = (*(__IO uint16_t*)Address); - /* Compare the read address with the virtual address */ - if (AddressValue != ERASED) { - /* In case variable value is read, reset ReadStatus flag */ - ReadStatus = 0; - break; - } - /* Next address location */ - Address += 4; - } - /* Return ReadStatus value: (0: Page not erased, 1: Sector erased) */ - return ReadStatus; -} - -/** - * @brief Returns the last stored variable data, if found, which correspond to - * the passed virtual address - * @param VirtAddress: Variable virtual address - * @param Data: Global variable contains the read variable value - * @retval Success or error status: - * - 0: if variable was found - * - 1: if the variable was not found - * - NO_VALID_PAGE: if no valid page was found. - */ -uint16_t EE_ReadVariable(uint16_t VirtAddress, uint16_t* Data) { - uint16_t ValidPage = PAGE0; - uint16_t AddressValue = 0x5555, ReadStatus = 1; - uint32_t Address = EEPROM_START_ADDRESS, PageStartAddress = EEPROM_START_ADDRESS; - - /* Get active Page for read operation */ - ValidPage = EE_FindValidPage(READ_FROM_VALID_PAGE); - - /* Check if there is no valid page */ - if (ValidPage == NO_VALID_PAGE) return NO_VALID_PAGE; - - /* Get the valid Page start Address */ - PageStartAddress = (uint32_t)(EEPROM_START_ADDRESS + (uint32_t)(ValidPage * PAGE_SIZE)); - - /* Get the valid Page end Address */ - Address = (uint32_t)((EEPROM_START_ADDRESS - 2) + (uint32_t)((1 + ValidPage) * PAGE_SIZE)); - - /* Check each active page address starting from end */ - while (Address > (PageStartAddress + 2)) { - /* Get the current location content to be compared with virtual address */ - AddressValue = (*(__IO uint16_t*)Address); - - /* Compare the read address with the virtual address */ - if (AddressValue == VirtAddress) { - /* Get content of Address-2 which is variable value */ - *Data = (*(__IO uint16_t*)(Address - 2)); - /* In case variable value is read, reset ReadStatus flag */ - ReadStatus = 0; - break; - } - else /* Next address location */ - Address -= 4; - } - /* Return ReadStatus value: (0: variable exist, 1: variable doesn't exist) */ - return ReadStatus; -} - -/** - * @brief Writes/upadtes variable data in EEPROM. - * @param VirtAddress: Variable virtual address - * @param Data: 16 bit data to be written - * @retval Success or error status: - * - FLASH_COMPLETE: on success - * - PAGE_FULL: if valid page is full - * - NO_VALID_PAGE: if no valid page was found - * - Flash error code: on write Flash error - */ -uint16_t EE_WriteVariable(uint16_t VirtAddress, uint16_t Data) { - /* Write the variable virtual address and value in the EEPROM */ - uint16_t Status = EE_VerifyPageFullWriteVariable(VirtAddress, Data); - - /* In case the EEPROM active page is full */ - if (Status == PAGE_FULL) /* Perform Page transfer */ - Status = EE_PageTransfer(VirtAddress, Data); - - /* Return last operation status */ - return Status; -} - -/** - * @brief Erases PAGE and PAGE1 and writes VALID_PAGE header to PAGE - * @param None - * @retval Status of the last operation (Flash write or erase) done during - * EEPROM formating - */ -static HAL_StatusTypeDef EE_Format(void) { - HAL_StatusTypeDef FlashStatus = HAL_OK; - uint32_t SectorError = 0; - FLASH_EraseInitTypeDef pEraseInit; - - pEraseInit.TypeErase = FLASH_TYPEERASE_SECTORS; - pEraseInit.Sector = PAGE0_ID; - pEraseInit.NbSectors = 1; - pEraseInit.VoltageRange = VOLTAGE_RANGE; - /* Erase Page0 */ - if (!EE_VerifyPageFullyErased(PAGE0_BASE_ADDRESS)) { - FlashStatus = HAL_FLASHEx_Erase(&pEraseInit, &SectorError); - /* If erase operation was failed, a Flash error code is returned */ - if (FlashStatus != HAL_OK) return FlashStatus; - } - /* Set Page0 as valid page: Write VALID_PAGE at Page0 base address */ - FlashStatus = HAL_FLASH_Program(TYPEPROGRAM_HALFWORD, PAGE0_BASE_ADDRESS, VALID_PAGE); - /* If program operation was failed, a Flash error code is returned */ - if (FlashStatus != HAL_OK) return FlashStatus; - - pEraseInit.Sector = PAGE1_ID; - /* Erase Page1 */ - if (!EE_VerifyPageFullyErased(PAGE1_BASE_ADDRESS)) { - FlashStatus = HAL_FLASHEx_Erase(&pEraseInit, &SectorError); - /* If erase operation was failed, a Flash error code is returned */ - if (FlashStatus != HAL_OK) return FlashStatus; - } - - return HAL_OK; -} - -/** - * @brief Find valid Page for write or read operation - * @param Operation: operation to achieve on the valid page. - * This parameter can be one of the following values: - * @arg READ_FROM_VALID_PAGE: read operation from valid page - * @arg WRITE_IN_VALID_PAGE: write operation from valid page - * @retval Valid page number (PAGE or PAGE1) or NO_VALID_PAGE in case - * of no valid page was found - */ -static uint16_t EE_FindValidPage(uint8_t Operation) { - uint16_t PageStatus0 = 6, PageStatus1 = 6; - - /* Get Page0 actual status */ - PageStatus0 = (*(__IO uint16_t*)PAGE0_BASE_ADDRESS); - - /* Get Page1 actual status */ - PageStatus1 = (*(__IO uint16_t*)PAGE1_BASE_ADDRESS); - - /* Write or read operation */ - switch (Operation) { - case WRITE_IN_VALID_PAGE: /* ---- Write operation ---- */ - if (PageStatus1 == VALID_PAGE) { - /* Page0 receiving data */ - if (PageStatus0 == RECEIVE_DATA) return PAGE0; /* Page0 valid */ - else return PAGE1; /* Page1 valid */ - } - else if (PageStatus0 == VALID_PAGE) { - /* Page1 receiving data */ - if (PageStatus1 == RECEIVE_DATA) return PAGE1; /* Page1 valid */ - else return PAGE0; /* Page0 valid */ - } - else - return NO_VALID_PAGE; /* No valid Page */ - - case READ_FROM_VALID_PAGE: /* ---- Read operation ---- */ - if (PageStatus0 == VALID_PAGE) - return PAGE0; /* Page0 valid */ - else if (PageStatus1 == VALID_PAGE) - return PAGE1; /* Page1 valid */ - else - return NO_VALID_PAGE; /* No valid Page */ - - default: - return PAGE0; /* Page0 valid */ - } -} - -/** - * @brief Verify if active page is full and Writes variable in EEPROM. - * @param VirtAddress: 16 bit virtual address of the variable - * @param Data: 16 bit data to be written as variable value - * @retval Success or error status: - * - FLASH_COMPLETE: on success - * - PAGE_FULL: if valid page is full - * - NO_VALID_PAGE: if no valid page was found - * - Flash error code: on write Flash error - */ -static uint16_t EE_VerifyPageFullWriteVariable(uint16_t VirtAddress, uint16_t Data) { - HAL_StatusTypeDef FlashStatus = HAL_OK; - uint16_t ValidPage = PAGE0; - uint32_t Address = EEPROM_START_ADDRESS, PageEndAddress = EEPROM_START_ADDRESS+PAGE_SIZE; - - /* Get valid Page for write operation */ - ValidPage = EE_FindValidPage(WRITE_IN_VALID_PAGE); - - /* Check if there is no valid page */ - if (ValidPage == NO_VALID_PAGE) return NO_VALID_PAGE; - - /* Get the valid Page start Address */ - Address = (uint32_t)(EEPROM_START_ADDRESS + (uint32_t)(ValidPage * PAGE_SIZE)); - - /* Get the valid Page end Address */ - PageEndAddress = (uint32_t)((EEPROM_START_ADDRESS - 1) + (uint32_t)((ValidPage + 1) * PAGE_SIZE)); - - /* Check each active page address starting from begining */ - while (Address < PageEndAddress) { - /* Verify if Address and Address+2 contents are 0xFFFFFFFF */ - if ((*(__IO uint32_t*)Address) == 0xFFFFFFFF) { - /* Set variable data */ - FlashStatus = HAL_FLASH_Program(TYPEPROGRAM_HALFWORD, Address, Data); - /* If program operation was failed, a Flash error code is returned */ - if (FlashStatus != HAL_OK) return FlashStatus; - /* Set variable virtual address */ - FlashStatus = HAL_FLASH_Program(TYPEPROGRAM_HALFWORD, Address + 2, VirtAddress); - /* Return program operation status */ - return FlashStatus; - } - else /* Next address location */ - Address += 4; - } - - /* Return PAGE_FULL in case the valid page is full */ - return PAGE_FULL; -} - -/** - * @brief Transfers last updated variables data from the full Page to - * an empty one. - * @param VirtAddress: 16 bit virtual address of the variable - * @param Data: 16 bit data to be written as variable value - * @retval Success or error status: - * - FLASH_COMPLETE: on success - * - PAGE_FULL: if valid page is full - * - NO_VALID_PAGE: if no valid page was found - * - Flash error code: on write Flash error - */ -static uint16_t EE_PageTransfer(uint16_t VirtAddress, uint16_t Data) { - HAL_StatusTypeDef FlashStatus = HAL_OK; - uint32_t NewPageAddress = EEPROM_START_ADDRESS; - uint16_t OldPageId=0; - uint16_t ValidPage = PAGE0, VarIdx = 0; - uint16_t EepromStatus = 0, ReadStatus = 0; - uint32_t SectorError = 0; - FLASH_EraseInitTypeDef pEraseInit; - - /* Get active Page for read operation */ - ValidPage = EE_FindValidPage(READ_FROM_VALID_PAGE); - - if (ValidPage == PAGE1) { /* Page1 valid */ - /* New page address where variable will be moved to */ - NewPageAddress = PAGE0_BASE_ADDRESS; - /* Old page ID where variable will be taken from */ - OldPageId = PAGE1_ID; - } - else if (ValidPage == PAGE0) { /* Page0 valid */ - /* New page address where variable will be moved to */ - NewPageAddress = PAGE1_BASE_ADDRESS; - /* Old page ID where variable will be taken from */ - OldPageId = PAGE0_ID; - } - else - return NO_VALID_PAGE; /* No valid Page */ - - /* Set the new Page status to RECEIVE_DATA status */ - FlashStatus = HAL_FLASH_Program(TYPEPROGRAM_HALFWORD, NewPageAddress, RECEIVE_DATA); - /* If program operation was failed, a Flash error code is returned */ - if (FlashStatus != HAL_OK) return FlashStatus; - - /* Write the variable passed as parameter in the new active page */ - EepromStatus = EE_VerifyPageFullWriteVariable(VirtAddress, Data); - /* If program operation was failed, a Flash error code is returned */ - if (EepromStatus != HAL_OK) return EepromStatus; - - /* Transfer process: transfer variables from old to the new active page */ - for (VarIdx = 0; VarIdx < NB_OF_VAR; VarIdx++) { - if (VirtAddVarTab[VarIdx] != VirtAddress) { /* Check each variable except the one passed as parameter */ - /* Read the other last variable updates */ - ReadStatus = EE_ReadVariable(VirtAddVarTab[VarIdx], &DataVar); - /* In case variable corresponding to the virtual address was found */ - if (ReadStatus != 0x1) { - /* Transfer the variable to the new active page */ - EepromStatus = EE_VerifyPageFullWriteVariable(VirtAddVarTab[VarIdx], DataVar); - /* If program operation was failed, a Flash error code is returned */ - if (EepromStatus != HAL_OK) return EepromStatus; - } - } - } - - pEraseInit.TypeErase = TYPEERASE_SECTORS; - pEraseInit.Sector = OldPageId; - pEraseInit.NbSectors = 1; - pEraseInit.VoltageRange = VOLTAGE_RANGE; - - /* Erase the old Page: Set old Page status to ERASED status */ - FlashStatus = HAL_FLASHEx_Erase(&pEraseInit, &SectorError); - /* If erase operation was failed, a Flash error code is returned */ - if (FlashStatus != HAL_OK) return FlashStatus; - - /* Set new Page status to VALID_PAGE status */ - FlashStatus = HAL_FLASH_Program(TYPEPROGRAM_HALFWORD, NewPageAddress, VALID_PAGE); - /* If program operation was failed, a Flash error code is returned */ - if (FlashStatus != HAL_OK) return FlashStatus; - - /* Return last operation flash status */ - return FlashStatus; -} - -#endif // STM32F4 || STM32F4xx - -/** - * @} - */ - -/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/ diff --git a/Marlin/src/HAL/HAL_STM32F4/EmulatedEeprom.cpp b/Marlin/src/HAL/HAL_STM32F4/EmulatedEeprom.cpp deleted file mode 100644 index fce5eb39f7..0000000000 --- a/Marlin/src/HAL/HAL_STM32F4/EmulatedEeprom.cpp +++ /dev/null @@ -1,142 +0,0 @@ -/** - * Marlin 3D Printer Firmware - * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] - * - * This program is free software: you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation, either version 3 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program. If not, see . - * - */ - -#if defined(STM32GENERIC) && (defined(STM32F4)) - -/** - * Description: functions for I2C connected external EEPROM. - * Not platform dependent. - */ - -#include "../../inc/MarlinConfig.h" - -#if ENABLED(EEPROM_SETTINGS) && DISABLED(I2C_EEPROM, SPI_EEPROM) - -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - -#include "HAL.h" -#include "EEPROM_Emul/eeprom_emul.h" - - -// -------------------------------------------------------------------------- -// Externals -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Local defines -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Types -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Variables -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Public Variables -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Private Variables -// -------------------------------------------------------------------------- -static bool eeprom_initialized = false; -// -------------------------------------------------------------------------- -// Function prototypes -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Private functions -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Public functions -// -------------------------------------------------------------------------- - -// FLASH_FLAG_PGSERR (Programming Sequence Error) was renamed to -// FLASH_FLAG_ERSERR (Erasing Sequence Error) in STM32F4 -// #define FLASH_FLAG_PGSERR FLASH_FLAG_ERSERR - -// -------------------------------------------------------------------------- -// EEPROM -// -------------------------------------------------------------------------- - - -void eeprom_init() { - if (!eeprom_initialized) { - HAL_FLASH_Unlock(); - - __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_EOP | FLASH_FLAG_OPERR | FLASH_FLAG_WRPERR |FLASH_FLAG_PGAERR | FLASH_FLAG_PGPERR | FLASH_FLAG_PGSERR); - - /* EEPROM Init */ - if (EE_Initialize() != EE_OK) - for (;;) HAL_Delay(1); // Spin forever until watchdog reset - - HAL_FLASH_Lock(); - eeprom_initialized = true; - } -} - -void eeprom_write_byte(uint8_t *pos, unsigned char value) { - uint16_t eeprom_address = (unsigned) pos; - - eeprom_init(); - - HAL_FLASH_Unlock(); - __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_EOP | FLASH_FLAG_OPERR | FLASH_FLAG_WRPERR |FLASH_FLAG_PGAERR | FLASH_FLAG_PGPERR | FLASH_FLAG_PGSERR); - - if (EE_WriteVariable(eeprom_address, (uint16_t) value) != EE_OK) - for (;;) HAL_Delay(1); // Spin forever until watchdog reset - - HAL_FLASH_Lock(); -} - -uint8_t eeprom_read_byte(uint8_t *pos) { - uint16_t data = 0xFF; - uint16_t eeprom_address = (unsigned)pos; - - eeprom_init(); - - if (EE_ReadVariable(eeprom_address, &data) != EE_OK) { - return (unsigned char)data; - } - return (unsigned char)data; -} - -void eeprom_read_block(void *__dst, const void *__src, size_t __n) { - uint16_t data = 0xFF; - uint16_t eeprom_address = (unsigned) __src; - - eeprom_init(); - - for (uint8_t c = 0; c < __n; c++) { - EE_ReadVariable(eeprom_address+c, &data); - *((uint8_t*)__dst + c) = data; - } -} - -void eeprom_update_block(const void *__src, void *__dst, size_t __n) { - -} - -#endif // EEPROM_SETTINGS && (!I2C_EEPROM && !SPI_EEPROM) -#endif // STM32GENERIC && STM32F4 diff --git a/Marlin/src/HAL/HAL_STM32F4/HAL.cpp b/Marlin/src/HAL/HAL_STM32F4/HAL.cpp deleted file mode 100644 index 3fa2aa2250..0000000000 --- a/Marlin/src/HAL/HAL_STM32F4/HAL.cpp +++ /dev/null @@ -1,133 +0,0 @@ -/** - * Marlin 3D Printer Firmware - * - * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] - * Copyright (c) 2016 Bob Cousins bobcousins42@googlemail.com - * Copyright (c) 2015-2016 Nico Tonnhofer wurstnase.reprap@gmail.com - * Copyright (c) 2017 Victor Perez - * - * This program is free software: you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation, either version 3 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program. If not, see . - * - */ - -#if defined(STM32GENERIC) && defined(STM32F4) - -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - -#include "HAL.h" - -//#include - -// -------------------------------------------------------------------------- -// Externals -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Local defines -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Types -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Variables -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Public Variables -// -------------------------------------------------------------------------- - -uint16_t HAL_adc_result; - -// -------------------------------------------------------------------------- -// Private Variables -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Function prototypes -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Private functions -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Public functions -// -------------------------------------------------------------------------- - -/* VGPV Done with defines -// disable interrupts -void cli(void) { noInterrupts(); } - -// enable interrupts -void sei(void) { interrupts(); } -*/ - -void HAL_clear_reset_source(void) { __HAL_RCC_CLEAR_RESET_FLAGS(); } - -uint8_t HAL_get_reset_source(void) { - if (__HAL_RCC_GET_FLAG(RCC_FLAG_IWDGRST) != RESET) return RST_WATCHDOG; - - if (__HAL_RCC_GET_FLAG(RCC_FLAG_SFTRST) != RESET) return RST_SOFTWARE; - if (__HAL_RCC_GET_FLAG(RCC_FLAG_PINRST) != RESET) return RST_EXTERNAL; - if (__HAL_RCC_GET_FLAG(RCC_FLAG_PORRST) != RESET) return RST_POWER_ON; - return 0; -} - -void _delay_ms(const int delay_ms) { delay(delay_ms); } - -extern "C" { - extern unsigned int _ebss; // end of bss section -} - -// return free memory between end of heap (or end bss) and whatever is current - -/* -#include "wirish/syscalls.c" -//extern caddr_t _sbrk(int incr); -#ifndef CONFIG_HEAP_END -extern char _lm_heap_end; -#define CONFIG_HEAP_END ((caddr_t)&_lm_heap_end) -#endif - -extern "C" { - static int freeMemory() { - char top = 't'; - return &top - reinterpret_cast(sbrk(0)); - } - int freeMemory() { - int free_memory; - int heap_end = (int)_sbrk(0); - free_memory = ((int)&free_memory) - ((int)heap_end); - return free_memory; - } -} -*/ - -// -------------------------------------------------------------------------- -// ADC -// -------------------------------------------------------------------------- - -void HAL_adc_start_conversion(const uint8_t adc_pin) { - HAL_adc_result = analogRead(adc_pin); -} - -uint16_t HAL_adc_get_result(void) { - return HAL_adc_result; -} - -#endif // // STM32GENERIC && STM32F4 diff --git a/Marlin/src/HAL/HAL_STM32F4/HAL.h b/Marlin/src/HAL/HAL_STM32F4/HAL.h deleted file mode 100644 index 44fb909598..0000000000 --- a/Marlin/src/HAL/HAL_STM32F4/HAL.h +++ /dev/null @@ -1,236 +0,0 @@ -/** - * Marlin 3D Printer Firmware - * - * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] - * Copyright (c) 2016 Bob Cousins bobcousins42@googlemail.com - * Copyright (c) 2015-2016 Nico Tonnhofer wurstnase.reprap@gmail.com - * Copyright (c) 2017 Victor Perez - * - * This program is free software: you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation, either version 3 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program. If not, see . - * - */ -#pragma once - -#define CPU_32_BIT - -#ifndef vsnprintf_P - #define vsnprintf_P vsnprintf -#endif - -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - -#include "../shared/Marduino.h" -#include "../shared/math_32bit.h" -#include "../shared/HAL_SPI.h" -#include "fastio_STM32F4.h" -#include "watchdog_STM32F4.h" -#include "HAL_timers_STM32F4.h" - -#include "../../inc/MarlinConfigPre.h" - -#include - -#ifdef USBCON - #include -#endif - -// -------------------------------------------------------------------------- -// Defines -// -------------------------------------------------------------------------- - -//Serial override -//extern HalSerial usb_serial; - -#if SERIAL_PORT == 0 - #error "Serial port 0 does not exist" -#endif - -#if !WITHIN(SERIAL_PORT, -1, 6) - #error "SERIAL_PORT must be from -1 to 6" -#endif -#if SERIAL_PORT == -1 - #define MYSERIAL0 SerialUSB -#elif SERIAL_PORT == 1 - #define MYSERIAL0 SerialUART1 -#elif SERIAL_PORT == 2 - #define MYSERIAL0 SerialUART2 -#elif SERIAL_PORT == 3 - #define MYSERIAL0 SerialUART3 -#elif SERIAL_PORT == 4 - #define MYSERIAL0 SerialUART4 -#elif SERIAL_PORT == 5 - #define MYSERIAL0 SerialUART5 -#elif SERIAL_PORT == 6 - #define MYSERIAL0 SerialUART6 -#endif - -#ifdef SERIAL_PORT_2 - #if SERIAL_PORT_2 == 0 - #error "Serial port 0 does not exist" - #endif - - #if !WITHIN(SERIAL_PORT_2, -1, 6) - #error "SERIAL_PORT_2 must be from -1 to 6" - #elif SERIAL_PORT_2 == SERIAL_PORT - #error "SERIAL_PORT_2 must be different than SERIAL_PORT" - #endif - #define NUM_SERIAL 2 - #if SERIAL_PORT_2 == -1 - #define MYSERIAL1 SerialUSB - #elif SERIAL_PORT_2 == 1 - #define MYSERIAL1 SerialUART1 - #elif SERIAL_PORT_2 == 2 - #define MYSERIAL1 SerialUART2 - #elif SERIAL_PORT_2 == 3 - #define MYSERIAL1 SerialUART3 - #elif SERIAL_PORT_2 == 4 - #define MYSERIAL1 SerialUART4 - #elif SERIAL_PORT_2 == 5 - #define MYSERIAL1 SerialUART5 - #elif SERIAL_PORT_2 == 6 - #define MYSERIAL1 SerialUART6 - #endif -#else - #define NUM_SERIAL 1 -#endif - -#undef _BV -#define _BV(b) (1 << (b)) - -/** - * TODO: review this to return 1 for pins that are not analog input - */ -#ifndef analogInputToDigitalPin - #define analogInputToDigitalPin(p) (p) -#endif - -#define CRITICAL_SECTION_START uint32_t primask = __get_PRIMASK(); __disable_irq() -#define CRITICAL_SECTION_END if (!primask) __enable_irq() -#define ISRS_ENABLED() (!__get_PRIMASK()) -#define ENABLE_ISRS() __enable_irq() -#define DISABLE_ISRS() __disable_irq() -#define cli() __disable_irq() -#define sei() __enable_irq() - -// On AVR this is in math.h? -#define square(x) ((x)*(x)) - -#ifndef strncpy_P - #define strncpy_P(dest, src, num) strncpy((dest), (src), (num)) -#endif - -// Fix bug in pgm_read_ptr -#undef pgm_read_ptr -#define pgm_read_ptr(addr) (*(addr)) - -// -------------------------------------------------------------------------- -// Types -// -------------------------------------------------------------------------- - -typedef int8_t pin_t; - -#define HAL_SERVO_LIB libServo - -// -------------------------------------------------------------------------- -// Public Variables -// -------------------------------------------------------------------------- - -/** result of last ADC conversion */ -extern uint16_t HAL_adc_result; - -// -------------------------------------------------------------------------- -// Public functions -// -------------------------------------------------------------------------- - -// Memory related -#define __bss_end __bss_end__ - -inline void HAL_init(void) { } - -/** clear reset reason */ -void HAL_clear_reset_source (void); - -/** reset reason */ -uint8_t HAL_get_reset_source(void); - -void _delay_ms(const int delay); - -/* -extern "C" { - int freeMemory(void); -} -*/ - -extern "C" char* _sbrk(int incr); - -/* -static int freeMemory() { - volatile int top; - top = (int)((char*)&top - reinterpret_cast(_sbrk(0))); - return top; -} -*/ - -static int freeMemory() { - volatile char top; - return &top - reinterpret_cast(_sbrk(0)); -} - -// -// SPI: Extended functions which take a channel number (hardware SPI only) -// - -/** Write single byte to specified SPI channel */ -void spiSend(uint32_t chan, byte b); -/** Write buffer to specified SPI channel */ -void spiSend(uint32_t chan, const uint8_t* buf, size_t n); -/** Read single byte from specified SPI channel */ -uint8_t spiRec(uint32_t chan); - -// -// EEPROM -// - -/** - * TODO: Write all this EEPROM stuff. Can emulate EEPROM in flash as last resort. - * Wire library should work for i2c EEPROMs. - */ -void eeprom_write_byte(uint8_t *pos, unsigned char value); -uint8_t eeprom_read_byte(uint8_t *pos); -void eeprom_read_block (void *__dst, const void *__src, size_t __n); -void eeprom_update_block (const void *__src, void *__dst, size_t __n); - -// -// ADC -// - -#define HAL_ANALOG_SELECT(pin) pinMode(pin, INPUT) - -inline void HAL_adc_init(void) {} - -#define HAL_START_ADC(pin) HAL_adc_start_conversion(pin) -#define HAL_READ_ADC() HAL_adc_result -#define HAL_ADC_READY() true - -void HAL_adc_start_conversion(const uint8_t adc_pin); -uint16_t HAL_adc_get_result(void); - -#define GET_PIN_MAP_PIN(index) index -#define GET_PIN_MAP_INDEX(pin) pin -#define PARSED_PIN_INDEX(code, dval) parser.intval(code, dval) - -#define JTAG_DISABLE() afio_cfg_debug_ports(AFIO_DEBUG_SW_ONLY) -#define JTAGSWD_DISABLE() afio_cfg_debug_ports(AFIO_DEBUG_NONE) diff --git a/Marlin/src/HAL/HAL_STM32F4/HAL_Servo_STM32F4.cpp b/Marlin/src/HAL/HAL_STM32F4/HAL_Servo_STM32F4.cpp deleted file mode 100644 index d8545cc9e0..0000000000 --- a/Marlin/src/HAL/HAL_STM32F4/HAL_Servo_STM32F4.cpp +++ /dev/null @@ -1,53 +0,0 @@ -/** - * Marlin 3D Printer Firmware - * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] - * - * Based on Sprinter and grbl. - * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm - * Copyright (c) 2017 Victor Perez - * - * This program is free software: you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation, either version 3 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program. If not, see . - * - */ - -#if defined(STM32GENERIC) && defined(STM32F4) - -#include "../../inc/MarlinConfig.h" - -#if HAS_SERVOS - -#include "HAL_Servo_STM32F4.h" - -int8_t libServo::attach(const int pin) { - return Servo::attach(pin); -} - -int8_t libServo::attach(const int pin, const int min, const int max) { - return Servo::attach(pin, min, max); -} - -void libServo::move(const int value) { - constexpr uint16_t servo_delay[] = SERVO_DELAY; - static_assert(COUNT(servo_delay) == NUM_SERVOS, "SERVO_DELAY must be an array NUM_SERVOS long."); - if (this->attach(0) >= 0) { - this->write(value); - safe_delay(servo_delay[this->servoIndex]); - #if ENABLED(DEACTIVATE_SERVOS_AFTER_MOVE) - this->detach(); - #endif - } -} -#endif // HAS_SERVOS - -#endif // STM32GENERIC && STM32F4 diff --git a/Marlin/src/HAL/HAL_STM32F4/fastio_STM32F4.h b/Marlin/src/HAL/HAL_STM32F4/fastio_STM32F4.h deleted file mode 100644 index a657d2c747..0000000000 --- a/Marlin/src/HAL/HAL_STM32F4/fastio_STM32F4.h +++ /dev/null @@ -1,153 +0,0 @@ -/** - * Marlin 3D Printer Firmware - * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] - * - * Based on Sprinter and grbl. - * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm - * Copyright (c) 2017 Victor Perez - * - * This program is free software: you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation, either version 3 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program. If not, see . - * - */ -#pragma once - -/** - * Fast I/O interfaces for STM32F4 - * These use GPIO functions instead of Direct Port Manipulation, as on AVR. - */ - -#undef _BV -#define _BV(b) (1 << (b)) - -#define READ(IO) digitalRead(IO) -#define WRITE(IO,V) digitalWrite(IO,V) - -#define _GET_MODE(IO) -#define _SET_MODE(IO,M) pinMode(IO, M) -#define _SET_OUTPUT(IO) pinMode(IO, OUTPUT) /*!< Output Push Pull Mode & GPIO_NOPULL */ - -#define OUT_WRITE(IO,V) do{ _SET_OUTPUT(IO); WRITE(IO,V); }while(0) - -#define SET_INPUT(IO) _SET_MODE(IO, INPUT) /*!< Input Floating Mode */ -#define SET_INPUT_PULLUP(IO) _SET_MODE(IO, INPUT_PULLUP) /*!< Input with Pull-up activation */ -#define SET_INPUT_PULLDOWN(IO) _SET_MODE(IO, INPUT_PULLDOWN) /*!< Input with Pull-down activation */ -#define SET_OUTPUT(IO) OUT_WRITE(IO, LOW) -#define SET_PWM(IO) pinMode(IO, PWM) - -#define TOGGLE(IO) OUT_WRITE(IO, !READ(IO)) - -#define IS_INPUT(IO) -#define IS_OUTPUT(IO) - -#define PWM_PIN(P) true - -// digitalRead/Write wrappers -#define extDigitalRead(IO) digitalRead(IO) -#define extDigitalWrite(IO,V) digitalWrite(IO,V) - -// -// Pins Definitions -// -#define PORTA 0 -#define PORTB 1 -#define PORTC 2 -#define PORTD 3 -#define PORTE 4 - -#define _STM32_PIN(_PORT,_PIN) ((PORT##_PORT * 16) + _PIN) - -#define PA0 _STM32_PIN(A, 0) -#define PA1 _STM32_PIN(A, 1) -#define PA2 _STM32_PIN(A, 2) -#define PA3 _STM32_PIN(A, 3) -#define PA4 _STM32_PIN(A, 4) -#define PA5 _STM32_PIN(A, 5) -#define PA6 _STM32_PIN(A, 6) -#define PA7 _STM32_PIN(A, 7) -#define PA8 _STM32_PIN(A, 8) -#define PA9 _STM32_PIN(A, 9) -#define PA10 _STM32_PIN(A, 10) -#define PA11 _STM32_PIN(A, 11) -#define PA12 _STM32_PIN(A, 12) -#define PA13 _STM32_PIN(A, 13) -#define PA14 _STM32_PIN(A, 14) -#define PA15 _STM32_PIN(A, 15) - -#define PB0 _STM32_PIN(B, 0) -#define PB1 _STM32_PIN(B, 1) -#define PB2 _STM32_PIN(B, 2) -#define PB3 _STM32_PIN(B, 3) -#define PB4 _STM32_PIN(B, 4) -#define PB5 _STM32_PIN(B, 5) -#define PB6 _STM32_PIN(B, 6) -#define PB7 _STM32_PIN(B, 7) -#define PB8 _STM32_PIN(B, 8) -#define PB9 _STM32_PIN(B, 9) -#define PB10 _STM32_PIN(B, 10) -#define PB11 _STM32_PIN(B, 11) -#define PB12 _STM32_PIN(B, 12) -#define PB13 _STM32_PIN(B, 13) -#define PB14 _STM32_PIN(B, 14) -#define PB15 _STM32_PIN(B, 15) - -#define PC0 _STM32_PIN(C, 0) -#define PC1 _STM32_PIN(C, 1) -#define PC2 _STM32_PIN(C, 2) -#define PC3 _STM32_PIN(C, 3) -#define PC4 _STM32_PIN(C, 4) -#define PC5 _STM32_PIN(C, 5) -#define PC6 _STM32_PIN(C, 6) -#define PC7 _STM32_PIN(C, 7) -#define PC8 _STM32_PIN(C, 8) -#define PC9 _STM32_PIN(C, 9) -#define PC10 _STM32_PIN(C, 10) -#define PC11 _STM32_PIN(C, 11) -#define PC12 _STM32_PIN(C, 12) -#define PC13 _STM32_PIN(C, 13) -#define PC14 _STM32_PIN(C, 14) -#define PC15 _STM32_PIN(C, 15) - -#define PD0 _STM32_PIN(D, 0) -#define PD1 _STM32_PIN(D, 1) -#define PD2 _STM32_PIN(D, 2) -#define PD3 _STM32_PIN(D, 3) -#define PD4 _STM32_PIN(D, 4) -#define PD5 _STM32_PIN(D, 5) -#define PD6 _STM32_PIN(D, 6) -#define PD7 _STM32_PIN(D, 7) -#define PD8 _STM32_PIN(D, 8) -#define PD9 _STM32_PIN(D, 9) -#define PD10 _STM32_PIN(D, 10) -#define PD11 _STM32_PIN(D, 11) -#define PD12 _STM32_PIN(D, 12) -#define PD13 _STM32_PIN(D, 13) -#define PD14 _STM32_PIN(D, 14) -#define PD15 _STM32_PIN(D, 15) - -#define PE0 _STM32_PIN(E, 0) -#define PE1 _STM32_PIN(E, 1) -#define PE2 _STM32_PIN(E, 2) -#define PE3 _STM32_PIN(E, 3) -#define PE4 _STM32_PIN(E, 4) -#define PE5 _STM32_PIN(E, 5) -#define PE6 _STM32_PIN(E, 6) -#define PE7 _STM32_PIN(E, 7) -#define PE8 _STM32_PIN(E, 8) -#define PE9 _STM32_PIN(E, 9) -#define PE10 _STM32_PIN(E, 10) -#define PE11 _STM32_PIN(E, 11) -#define PE12 _STM32_PIN(E, 12) -#define PE13 _STM32_PIN(E, 13) -#define PE14 _STM32_PIN(E, 14) -#define PE15 _STM32_PIN(E, 15) diff --git a/Marlin/src/HAL/HAL_STM32F4/persistent_store_eeprom.cpp b/Marlin/src/HAL/HAL_STM32F4/persistent_store_eeprom.cpp deleted file mode 100644 index 811b1ed9f4..0000000000 --- a/Marlin/src/HAL/HAL_STM32F4/persistent_store_eeprom.cpp +++ /dev/null @@ -1,69 +0,0 @@ -/** - * Marlin 3D Printer Firmware - * - * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] - * Copyright (c) 2016 Bob Cousins bobcousins42@googlemail.com - * Copyright (c) 2015-2016 Nico Tonnhofer wurstnase.reprap@gmail.com - * Copyright (c) 2016 Victor Perez victor_pv@hotmail.com - * - * This program is free software: you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation, either version 3 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program. If not, see . - * - */ - -#if defined(STM32GENERIC) && defined(STM32F4) - -#include "../shared/persistent_store_api.h" - -#include "../../inc/MarlinConfig.h" - -#if ENABLED(EEPROM_SETTINGS) - -bool PersistentStore::access_start() { return true; } -bool PersistentStore::access_finish() { return true; } - -bool PersistentStore::write_data(int &pos, const uint8_t *value, size_t size, uint16_t *crc) { - while (size--) { - uint8_t * const p = (uint8_t * const)pos; - uint8_t v = *value; - // EEPROM has only ~100,000 write cycles, - // so only write bytes that have changed! - if (v != eeprom_read_byte(p)) { - eeprom_write_byte(p, v); - if (eeprom_read_byte(p) != v) { - SERIAL_ECHO_MSG(MSG_ERR_EEPROM_WRITE); - return true; - } - } - crc16(crc, &v, 1); - pos++; - value++; - }; - return false; -} - -bool PersistentStore::read_data(int &pos, uint8_t* value, size_t size, uint16_t *crc, const bool writing) { - do { - uint8_t c = eeprom_read_byte((uint8_t*)pos); - if (writing) *value = c; - crc16(crc, &c, 1); - pos++; - value++; - } while (--size); - return false; -} - -size_t PersistentStore::capacity() { return E2END + 1; } - -#endif // EEPROM_SETTINGS -#endif // STM32GENERIC && STM32F4 diff --git a/Marlin/src/HAL/HAL_STM32F4/pinsDebug.h b/Marlin/src/HAL/HAL_STM32F4/pinsDebug.h deleted file mode 100644 index e5022f79a4..0000000000 --- a/Marlin/src/HAL/HAL_STM32F4/pinsDebug.h +++ /dev/null @@ -1 +0,0 @@ -#error Debug pins is not supported on this Platform! diff --git a/Marlin/src/HAL/HAL_STM32F7/EEPROM_Emul/eeprom_emul.h b/Marlin/src/HAL/HAL_STM32F7/EEPROM_Emul/eeprom_emul.h deleted file mode 100644 index 8cffdbef77..0000000000 --- a/Marlin/src/HAL/HAL_STM32F7/EEPROM_Emul/eeprom_emul.h +++ /dev/null @@ -1,111 +0,0 @@ -/****************************************************************************** - * @file eeprom_emul.h - * @author MCD Application Team - * @version V1.2.6 - * @date 04-November-2016 - * @brief This file contains all the functions prototypes for the EEPROM - * emulation firmware library. - ****************************************************************************** - * @attention - * - *

© Copyright © 2016 STMicroelectronics International N.V. - * All rights reserved.

- * - * Redistribution and use in source and binary forms, with or without - * modification, are permitted, provided that the following conditions are met: - * - * 1. Redistribution of source code must retain the above copyright notice, - * this list of conditions and the following disclaimer. - * 2. Redistributions in binary form must reproduce the above copyright notice, - * this list of conditions and the following disclaimer in the documentation - * and/or other materials provided with the distribution. - * 3. Neither the name of STMicroelectronics nor the names of other - * contributors to this software may be used to endorse or promote products - * derived from this software without specific written permission. - * 4. This software, including modifications and/or derivative works of this - * software, must execute solely and exclusively on microcontroller or - * microprocessor devices manufactured by or for STMicroelectronics. - * 5. Redistribution and use of this software other than as permitted under - * this license is void and will automatically terminate your rights under - * this license. - * - * THIS SOFTWARE IS PROVIDED BY STMICROELECTRONICS AND CONTRIBUTORS "AS IS" - * AND ANY EXPRESS, IMPLIED OR STATUTORY WARRANTIES, INCLUDING, BUT NOT - * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A - * PARTICULAR PURPOSE AND NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY - * RIGHTS ARE DISCLAIMED TO THE FULLEST EXTENT PERMITTED BY LAW. IN NO EVENT - * SHALL STMICROELECTRONICS OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, - * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT - * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, - * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF - * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING - * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, - * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - *****************************************************************************/ -#pragma once - -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- -#include "../../../inc/MarlinConfig.h" -#include "../HAL.h" - -/* Exported constants --------------------------------------------------------*/ -/* EEPROM emulation firmware error codes */ -#define EE_OK (uint32_t)HAL_OK -#define EE_ERROR (uint32_t)HAL_ERROR -#define EE_BUSY (uint32_t)HAL_BUSY -#define EE_TIMEOUT (uint32_t)HAL_TIMEOUT - -/* Define the size of the sectors to be used */ -#define PAGE_SIZE (uint32_t)0x4000 /* Page size = 16KByte */ - -/* Device voltage range supposed to be [2.7V to 3.6V], the operation will - be done by word */ -#define VOLTAGE_RANGE (uint8_t)VOLTAGE_RANGE_3 - -/* EEPROM start address in Flash */ -#define EEPROM_START_ADDRESS ((uint32_t)0x08100000) /* EEPROM emulation start address: - from sector2 : after 16KByte of used - Flash memory */ - -/* Pages 0 and 1 base and end addresses */ -#define PAGE0_BASE_ADDRESS ((uint32_t)(EEPROM_START_ADDRESS + 0x0000)) -#define PAGE0_END_ADDRESS ((uint32_t)(EEPROM_START_ADDRESS + (PAGE_SIZE - 1))) -#define PAGE0_ID FLASH_SECTOR_1 - -#define PAGE1_BASE_ADDRESS ((uint32_t)(EEPROM_START_ADDRESS + 0x4000)) -#define PAGE1_END_ADDRESS ((uint32_t)(EEPROM_START_ADDRESS + (2 * PAGE_SIZE - 1))) -#define PAGE1_ID FLASH_SECTOR_2 - -/* Used Flash pages for EEPROM emulation */ -#define PAGE0 ((uint16_t)0x0000) -#define PAGE1 ((uint16_t)0x0001) /* Page nb between PAGE0_BASE_ADDRESS & PAGE1_BASE_ADDRESS*/ - -/* No valid page define */ -#define NO_VALID_PAGE ((uint16_t)0x00AB) - -/* Page status definitions */ -#define ERASED ((uint16_t)0xFFFF) /* Page is empty */ -#define RECEIVE_DATA ((uint16_t)0xEEEE) /* Page is marked to receive data */ -#define VALID_PAGE ((uint16_t)0x0000) /* Page containing valid data */ - -/* Valid pages in read and write defines */ -#define READ_FROM_VALID_PAGE ((uint8_t)0x00) -#define WRITE_IN_VALID_PAGE ((uint8_t)0x01) - -/* Page full define */ -#define PAGE_FULL ((uint8_t)0x80) - -/* Variables' number */ -#define NB_OF_VAR ((uint16_t)4096) - -/* Exported types ------------------------------------------------------------*/ -/* Exported macro ------------------------------------------------------------*/ -/* Exported functions ------------------------------------------------------- */ -uint16_t EE_Initialize(void); -uint16_t EE_ReadVariable(uint16_t VirtAddress, uint16_t* Data); -uint16_t EE_WriteVariable(uint16_t VirtAddress, uint16_t Data); - -/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/Marlin/src/HAL/HAL_STM32F7/EmulatedEeprom.cpp b/Marlin/src/HAL/HAL_STM32F7/EmulatedEeprom.cpp deleted file mode 100644 index a612b89538..0000000000 --- a/Marlin/src/HAL/HAL_STM32F7/EmulatedEeprom.cpp +++ /dev/null @@ -1,139 +0,0 @@ -/** - * Marlin 3D Printer Firmware - * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] - * - * This program is free software: you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation, either version 3 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program. If not, see . - * - */ - -#ifdef STM32F7 - -/** - * Description: functions for I2C connected external EEPROM. - * Not platform dependent. - */ - -#include "../../inc/MarlinConfig.h" - -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - -#include "HAL.h" -#include "EEPROM_Emul/eeprom_emul.h" - - -// -------------------------------------------------------------------------- -// Externals -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Local defines -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Types -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Variables -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Public Variables -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Private Variables -// -------------------------------------------------------------------------- -static bool eeprom_initialized = false; -// -------------------------------------------------------------------------- -// Function prototypes -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Private functions -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Public functions -// -------------------------------------------------------------------------- - -// FLASH_FLAG_PGSERR (Programming Sequence Error) was renamed to -// FLASH_FLAG_ERSERR (Erasing Sequence Error) in STM32F7 -#define FLASH_FLAG_PGSERR FLASH_FLAG_ERSERR - -// -------------------------------------------------------------------------- -// EEPROM -// -------------------------------------------------------------------------- - - -void eeprom_init() { - if (!eeprom_initialized) { - HAL_FLASH_Unlock(); - - __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_EOP | FLASH_FLAG_OPERR | FLASH_FLAG_WRPERR |FLASH_FLAG_PGAERR | FLASH_FLAG_PGPERR | FLASH_FLAG_PGSERR); - - /* EEPROM Init */ - if (EE_Initialize() != EE_OK) - for (;;) HAL_Delay(1); // Spin forever until watchdog reset - - HAL_FLASH_Lock(); - eeprom_initialized = true; - } -} - -void eeprom_write_byte(uint8_t *pos, unsigned char value) { - uint16_t eeprom_address = (unsigned) pos; - - eeprom_init(); - - HAL_FLASH_Unlock(); - __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_EOP | FLASH_FLAG_OPERR | FLASH_FLAG_WRPERR |FLASH_FLAG_PGAERR | FLASH_FLAG_PGPERR | FLASH_FLAG_PGSERR); - - if (EE_WriteVariable(eeprom_address, (uint16_t) value) != EE_OK) - for (;;) HAL_Delay(1); // Spin forever until watchdog reset - - HAL_FLASH_Lock(); -} - -uint8_t eeprom_read_byte(uint8_t *pos) { - uint16_t data = 0xFF; - uint16_t eeprom_address = (unsigned)pos; - - eeprom_init(); - - if (EE_ReadVariable(eeprom_address, &data) != EE_OK) { - return (unsigned char)data; - } - return (unsigned char)data; -} - -void eeprom_read_block(void *__dst, const void *__src, size_t __n) { - uint16_t data = 0xFF; - uint16_t eeprom_address = (unsigned) __src; - - eeprom_init(); - - for (uint8_t c = 0; c < __n; c++) { - EE_ReadVariable(eeprom_address+c, &data); - *((uint8_t*)__dst + c) = data; - } -} - -void eeprom_update_block(const void *__src, void *__dst, size_t __n) { - -} - -#endif // STM32F7 diff --git a/Marlin/src/HAL/HAL_STM32F7/HAL.cpp b/Marlin/src/HAL/HAL_STM32F7/HAL.cpp deleted file mode 100644 index e266eabf46..0000000000 --- a/Marlin/src/HAL/HAL_STM32F7/HAL.cpp +++ /dev/null @@ -1,139 +0,0 @@ -/** - * Marlin 3D Printer Firmware - * - * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] - * Copyright (c) 2016 Bob Cousins bobcousins42@googlemail.com - * Copyright (c) 2015-2016 Nico Tonnhofer wurstnase.reprap@gmail.com - * Copyright (c) 2017 Victor Perez - * - * This program is free software: you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation, either version 3 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program. If not, see . - * - */ - -#ifdef STM32F7 - -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - -#include "HAL.h" - -//#include - -// -------------------------------------------------------------------------- -// Externals -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Local defines -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Types -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Variables -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Public Variables -// -------------------------------------------------------------------------- - -uint16_t HAL_adc_result; - -// -------------------------------------------------------------------------- -// Private Variables -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Function prototypes -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Private functions -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Public functions -// -------------------------------------------------------------------------- - -/* VGPV Done with defines -// disable interrupts -void cli(void) { noInterrupts(); } - -// enable interrupts -void sei(void) { interrupts(); } -*/ - -void HAL_clear_reset_source(void) { __HAL_RCC_CLEAR_RESET_FLAGS(); } - -uint8_t HAL_get_reset_source(void) { - if (__HAL_RCC_GET_FLAG(RCC_FLAG_IWDGRST) != RESET) - return RST_WATCHDOG; - - if (__HAL_RCC_GET_FLAG(RCC_FLAG_SFTRST) != RESET) - return RST_SOFTWARE; - - if (__HAL_RCC_GET_FLAG(RCC_FLAG_PINRST) != RESET) - return RST_EXTERNAL; - - if (__HAL_RCC_GET_FLAG(RCC_FLAG_PORRST) != RESET) - return RST_POWER_ON; - return 0; -} - -void _delay_ms(const int delay_ms) { delay(delay_ms); } - -extern "C" { - extern unsigned int _ebss; // end of bss section -} - -// return free memory between end of heap (or end bss) and whatever is current - -/* -#include "wirish/syscalls.c" -//extern caddr_t _sbrk(int incr); -#ifndef CONFIG_HEAP_END -extern char _lm_heap_end; -#define CONFIG_HEAP_END ((caddr_t)&_lm_heap_end) -#endif - -extern "C" { - static int freeMemory() { - char top = 't'; - return &top - reinterpret_cast(sbrk(0)); - } - int freeMemory() { - int free_memory; - int heap_end = (int)_sbrk(0); - free_memory = ((int)&free_memory) - ((int)heap_end); - return free_memory; - } -} -*/ - -// -------------------------------------------------------------------------- -// ADC -// -------------------------------------------------------------------------- - -void HAL_adc_start_conversion(const uint8_t adc_pin) { - HAL_adc_result = analogRead(adc_pin); -} - -uint16_t HAL_adc_get_result(void) { - return HAL_adc_result; -} - -#endif // STM32F7 diff --git a/Marlin/src/HAL/HAL_STM32F7/HAL_spi_STM32F7.cpp b/Marlin/src/HAL/HAL_STM32F7/HAL_spi_STM32F7.cpp deleted file mode 100644 index 294d90414e..0000000000 --- a/Marlin/src/HAL/HAL_STM32F7/HAL_spi_STM32F7.cpp +++ /dev/null @@ -1,164 +0,0 @@ -/** - * Marlin 3D Printer Firmware - * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] - * - * Based on Sprinter and grbl. - * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm - * Copyright (c) 2017 Victor Perez - * - * This program is free software: you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation, either version 3 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program. If not, see . - * - */ - -/** - * Software SPI functions originally from Arduino Sd2Card Library - * Copyright (c) 2009 by William Greiman - */ - -/** - * Adapted to the STM32F7 HAL - */ - -#ifdef STM32F7 - -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - -#include "HAL.h" -#include "../shared/HAL_SPI.h" -#include -#include "spi_pins.h" -#include "../../core/macros.h" -#include - -// -------------------------------------------------------------------------- -// Public Variables -// -------------------------------------------------------------------------- - -static SPISettings spiConfig; - -// -------------------------------------------------------------------------- -// Public functions -// -------------------------------------------------------------------------- - -#if ENABLED(SOFTWARE_SPI) - // -------------------------------------------------------------------------- - // Software SPI - // -------------------------------------------------------------------------- - #error "Software SPI not supported for STM32F7. Use hardware SPI." - -#else - -// -------------------------------------------------------------------------- -// Hardware SPI -// -------------------------------------------------------------------------- - -/** - * VGPV SPI speed start and F_CPU/2, by default 72/2 = 36Mhz - */ - -/** - * @brief Begin SPI port setup - * - * @return Nothing - * - * @details Only configures SS pin since libmaple creates and initialize the SPI object - */ -void spiBegin(void) { - #if !PIN_EXISTS(SS) - #error SS_PIN not defined! - #endif - - OUT_WRITE(SS_PIN, HIGH); -} - -/** Configure SPI for specified SPI speed */ -void spiInit(uint8_t spiRate) { - // Use datarates Marlin uses - uint32_t clock; - switch (spiRate) { - case SPI_FULL_SPEED: clock = 20000000; break; // 13.9mhz=20000000 6.75mhz=10000000 3.38mhz=5000000 .833mhz=1000000 - case SPI_HALF_SPEED: clock = 5000000; break; - case SPI_QUARTER_SPEED: clock = 2500000; break; - case SPI_EIGHTH_SPEED: clock = 1250000; break; - case SPI_SPEED_5: clock = 625000; break; - case SPI_SPEED_6: clock = 300000; break; - default: - clock = 4000000; // Default from the SPI libarary - } - spiConfig = SPISettings(clock, MSBFIRST, SPI_MODE0); - SPI.begin(); -} - -/** - * @brief Receives a single byte from the SPI port. - * - * @return Byte received - * - * @details - */ -uint8_t spiRec(void) { - SPI.beginTransaction(spiConfig); - uint8_t returnByte = SPI.transfer(0xFF); - SPI.endTransaction(); - return returnByte; -} - -/** - * @brief Receives a number of bytes from the SPI port to a buffer - * - * @param buf Pointer to starting address of buffer to write to. - * @param nbyte Number of bytes to receive. - * @return Nothing - * - * @details Uses DMA - */ -void spiRead(uint8_t* buf, uint16_t nbyte) { - SPI.beginTransaction(spiConfig); - SPI.dmaTransfer(0, const_cast(buf), nbyte); - SPI.endTransaction(); -} - -/** - * @brief Sends a single byte on SPI port - * - * @param b Byte to send - * - * @details - */ -void spiSend(uint8_t b) { - SPI.beginTransaction(spiConfig); - SPI.transfer(b); - SPI.endTransaction(); -} - -/** - * @brief Write token and then write from 512 byte buffer to SPI (for SD card) - * - * @param buf Pointer with buffer start address - * @return Nothing - * - * @details Use DMA - */ -void spiSendBlock(uint8_t token, const uint8_t* buf) { - SPI.beginTransaction(spiConfig); - SPI.transfer(token); - SPI.dmaSend(const_cast(buf), 512); - SPI.endTransaction(); -} - -#endif // SOFTWARE_SPI - -#endif // STM32F7 diff --git a/Marlin/src/HAL/HAL_STM32F7/endstop_interrupts.h b/Marlin/src/HAL/HAL_STM32F7/endstop_interrupts.h deleted file mode 100644 index 86f6d68c59..0000000000 --- a/Marlin/src/HAL/HAL_STM32F7/endstop_interrupts.h +++ /dev/null @@ -1,64 +0,0 @@ -/** - * Marlin 3D Printer Firmware - * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] - * - * Based on Sprinter and grbl. - * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm - * Copyright (c) 2017 Victor Perez - * - * This program is free software: you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation, either version 3 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program. If not, see . - * - */ -#pragma once - -#include "../../module/endstops.h" - -// One ISR for all EXT-Interrupts -void endstop_ISR(void) { endstops.update(); } - -void setup_endstop_interrupts(void) { - #if HAS_X_MAX - attachInterrupt(X_MAX_PIN, endstop_ISR, CHANGE); - #endif - #if HAS_X_MIN - attachInterrupt(X_MIN_PIN, endstop_ISR, CHANGE); - #endif - #if HAS_Y_MAX - attachInterrupt(Y_MAX_PIN, endstop_ISR, CHANGE); - #endif - #if HAS_Y_MIN - attachInterrupt(Y_MIN_PIN, endstop_ISR, CHANGE); - #endif - #if HAS_Z_MAX - attachInterrupt(Z_MAX_PIN, endstop_ISR, CHANGE); - #endif - #if HAS_Z_MIN - attachInterrupt(Z_MIN_PIN, endstop_ISR, CHANGE); - #endif - #if HAS_Z2_MAX - attachInterrupt(Z2_MAX_PIN, endstop_ISR, CHANGE); - #endif - #if HAS_Z2_MIN - attachInterrupt(Z2_MIN_PIN, endstop_ISR, CHANGE); - #endif - #if HAS_Z3_MAX - attachInterrupt(Z3_MAX_PIN, endstop_ISR, CHANGE); - #endif - #if HAS_Z3_MIN - attachInterrupt(Z3_MIN_PIN, endstop_ISR, CHANGE); - #endif - #if HAS_Z_MIN_PROBE_PIN - attachInterrupt(Z_MIN_PROBE_PIN, endstop_ISR, CHANGE); - #endif -} diff --git a/Marlin/src/HAL/HAL_STM32F7/pinsDebug.h b/Marlin/src/HAL/HAL_STM32F7/pinsDebug.h deleted file mode 100644 index e5022f79a4..0000000000 --- a/Marlin/src/HAL/HAL_STM32F7/pinsDebug.h +++ /dev/null @@ -1 +0,0 @@ -#error Debug pins is not supported on this Platform! diff --git a/Marlin/src/HAL/HAL_STM32F7/watchdog_STM32F7.cpp b/Marlin/src/HAL/HAL_STM32F7/watchdog_STM32F7.cpp deleted file mode 100644 index 8b75454dad..0000000000 --- a/Marlin/src/HAL/HAL_STM32F7/watchdog_STM32F7.cpp +++ /dev/null @@ -1,52 +0,0 @@ -/** - * Marlin 3D Printer Firmware - * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] - * - * Based on Sprinter and grbl. - * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm - * - * This program is free software: you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation, either version 3 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program. If not, see . - * - */ - -#ifdef STM32F7 - -#include "../../inc/MarlinConfig.h" - -#if ENABLED(USE_WATCHDOG) - - #include "watchdog_STM32F7.h" - - IWDG_HandleTypeDef hiwdg; - - void watchdog_init() { - hiwdg.Instance = IWDG; - hiwdg.Init.Prescaler = IWDG_PRESCALER_32; //32kHz LSI clock and 32x prescalar = 1024Hz IWDG clock - hiwdg.Init.Reload = 4095; //4095 counts = 4 seconds at 1024Hz - if (HAL_IWDG_Init(&hiwdg) != HAL_OK) { - //Error_Handler(); - } - } - - void watchdog_reset() { - /* Refresh IWDG: reload counter */ - if (HAL_IWDG_Refresh(&hiwdg) != HAL_OK) { - /* Refresh Error */ - //Error_Handler(); - } - } - -#endif // USE_WATCHDOG - -#endif // STM32F7 diff --git a/Marlin/src/HAL/HAL_STM32_F4_F7/EmulatedEeprom.cpp b/Marlin/src/HAL/HAL_STM32_F4_F7/EmulatedEeprom.cpp new file mode 100644 index 0000000000..5e6ae09bf1 --- /dev/null +++ b/Marlin/src/HAL/HAL_STM32_F4_F7/EmulatedEeprom.cpp @@ -0,0 +1,122 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + +#if defined(STM32GENERIC) && (defined(STM32F4) || defined(STM32F7)) + +/** + * Description: Functions for a Flash emulated EEPROM + * Not platform dependent. + */ + +// Include configs and pins to get all EEPROM flags +#include "../../inc/MarlinConfig.h" + +#ifdef STM32F7 + #define HAS_EMULATED_EEPROM 1 +#else + #define HAS_EMULATED_EEPROM NONE(I2C_EEPROM, SPI_EEPROM) +#endif + +#if HAS_EMULATED_EEPROM && ENABLED(EEPROM_SETTINGS) + +// ------------------------ +// Includes +// ------------------------ + +#include "HAL.h" +#include "eeprom_emul.h" + +// ------------------------ +// Local defines +// ------------------------ + +// FLASH_FLAG_PGSERR (Programming Sequence Error) was renamed to +// FLASH_FLAG_ERSERR (Erasing Sequence Error) in STM32F4/7 + +#ifdef STM32F7 + #define FLASH_FLAG_PGSERR FLASH_FLAG_ERSERR +#else + //#define FLASH_FLAG_PGSERR FLASH_FLAG_ERSERR +#endif + +// ------------------------ +// Private Variables +// ------------------------ + +static bool eeprom_initialized = false; + +// ------------------------ +// Public functions +// ------------------------ + +void eeprom_init() { + if (!eeprom_initialized) { + HAL_FLASH_Unlock(); + + __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_EOP | FLASH_FLAG_OPERR | FLASH_FLAG_WRPERR |FLASH_FLAG_PGAERR | FLASH_FLAG_PGPERR | FLASH_FLAG_PGSERR); + + /* EEPROM Init */ + if (EE_Initialize() != EE_OK) + for (;;) HAL_Delay(1); // Spin forever until watchdog reset + + HAL_FLASH_Lock(); + eeprom_initialized = true; + } +} + +void eeprom_write_byte(uint8_t *pos, unsigned char value) { + eeprom_init(); + + HAL_FLASH_Unlock(); + __HAL_FLASH_CLEAR_FLAG(FLASH_FLAG_EOP | FLASH_FLAG_OPERR | FLASH_FLAG_WRPERR |FLASH_FLAG_PGAERR | FLASH_FLAG_PGPERR | FLASH_FLAG_PGSERR); + + uint16_t eeprom_address = unsigned(pos); + if (EE_WriteVariable(eeprom_address, uint16_t(value)) != EE_OK) + for (;;) HAL_Delay(1); // Spin forever until watchdog reset + + HAL_FLASH_Lock(); +} + +uint8_t eeprom_read_byte(uint8_t *pos) { + eeprom_init(); + + uint16_t data = 0xFF; + uint16_t eeprom_address = unsigned(pos); + (void)EE_ReadVariable(eeprom_address, &data); // Data unchanged on error + + return uint8_t(data); +} + +void eeprom_read_block(void *__dst, const void *__src, size_t __n) { + eeprom_init(); + + uint16_t data = 0xFF; + uint16_t eeprom_address = unsigned(__src); + for (uint8_t c = 0; c < __n; c++) { + EE_ReadVariable(eeprom_address+c, &data); + *((uint8_t*)__dst + c) = data; + } +} + +void eeprom_update_block(const void *__src, void *__dst, size_t __n) { + +} + +#endif // EEPROM_SETTINGS +#endif // STM32GENERIC && (STM32F4 || STM32F7) diff --git a/Marlin/src/HAL/HAL_STM32_F4_F7/HAL.cpp b/Marlin/src/HAL/HAL_STM32_F4_F7/HAL.cpp new file mode 100644 index 0000000000..3602c0d86b --- /dev/null +++ b/Marlin/src/HAL/HAL_STM32_F4_F7/HAL.cpp @@ -0,0 +1,96 @@ +/** + * Marlin 3D Printer Firmware + * + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * Copyright (c) 2016 Bob Cousins bobcousins42@googlemail.com + * Copyright (c) 2015-2016 Nico Tonnhofer wurstnase.reprap@gmail.com + * Copyright (c) 2017 Victor Perez + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + +#if defined(STM32GENERIC) && (defined(STM32F4) || defined(STM32F7)) + +#include "HAL.h" + +//#include + +// ------------------------ +// Public Variables +// ------------------------ + +uint16_t HAL_adc_result; + +// ------------------------ +// Public functions +// ------------------------ + +/* VGPV Done with defines +// disable interrupts +void cli(void) { noInterrupts(); } + +// enable interrupts +void sei(void) { interrupts(); } +*/ + +void HAL_clear_reset_source(void) { __HAL_RCC_CLEAR_RESET_FLAGS(); } + +uint8_t HAL_get_reset_source(void) { + if (__HAL_RCC_GET_FLAG(RCC_FLAG_IWDGRST) != RESET) return RST_WATCHDOG; + if (__HAL_RCC_GET_FLAG(RCC_FLAG_SFTRST) != RESET) return RST_SOFTWARE; + if (__HAL_RCC_GET_FLAG(RCC_FLAG_PINRST) != RESET) return RST_EXTERNAL; + if (__HAL_RCC_GET_FLAG(RCC_FLAG_PORRST) != RESET) return RST_POWER_ON; + return 0; +} + +void _delay_ms(const int delay_ms) { delay(delay_ms); } + +extern "C" { + extern unsigned int _ebss; // end of bss section +} + +// return free memory between end of heap (or end bss) and whatever is current + +/* +#include "wirish/syscalls.c" +//extern caddr_t _sbrk(int incr); +#ifndef CONFIG_HEAP_END +extern char _lm_heap_end; +#define CONFIG_HEAP_END ((caddr_t)&_lm_heap_end) +#endif + +extern "C" { + static int freeMemory() { + char top = 't'; + return &top - reinterpret_cast(sbrk(0)); + } + int freeMemory() { + int free_memory; + int heap_end = (int)_sbrk(0); + free_memory = ((int)&free_memory) - ((int)heap_end); + return free_memory; + } +} +*/ + +// ------------------------ +// ADC +// ------------------------ + +void HAL_adc_start_conversion(const uint8_t adc_pin) { HAL_adc_result = analogRead(adc_pin); } + +uint16_t HAL_adc_get_result(void) { return HAL_adc_result; } + +#endif // STM32GENERIC && (STM32F4 || STM32F7) diff --git a/Marlin/src/HAL/HAL_STM32F7/HAL.h b/Marlin/src/HAL/HAL_STM32_F4_F7/HAL.h similarity index 82% rename from Marlin/src/HAL/HAL_STM32F7/HAL.h rename to Marlin/src/HAL/HAL_STM32_F4_F7/HAL.h index be99165111..59623ae706 100644 --- a/Marlin/src/HAL/HAL_STM32F7/HAL.h +++ b/Marlin/src/HAL/HAL_STM32_F4_F7/HAL.h @@ -24,34 +24,34 @@ #define CPU_32_BIT -#ifndef vsnprintf_P - #define vsnprintf_P vsnprintf -#endif - -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - -#include - #include "../shared/Marduino.h" #include "../shared/math_32bit.h" #include "../shared/HAL_SPI.h" -#include "fastio_STM32F7.h" -#include "watchdog_STM32F7.h" +#include "fastio_STM32_F4_F7.h" +#include "watchdog_STM32_F4_F7.h" -#include "HAL_timers_STM32F7.h" +#include "HAL_timers_STM32_F4_F7.h" #include "../../inc/MarlinConfigPre.h" -// -------------------------------------------------------------------------- +#include + +#ifdef defined(STM32F4) && USBCON + #include +#endif + +// ------------------------ // Defines -// -------------------------------------------------------------------------- +// ------------------------ //Serial override //extern HalSerial usb_serial; +#if defined(STM32F4) && SERIAL_PORT == 0 + #error "Serial port 0 does not exist" +#endif + #if !WITHIN(SERIAL_PORT, -1, 6) #error "SERIAL_PORT must be from -1 to 6" #endif @@ -72,6 +72,9 @@ #endif #ifdef SERIAL_PORT_2 + #if defined(STM32F4) && SERIAL_PORT_2 == 0 + #error "Serial port 0 does not exist" + #endif #if !WITHIN(SERIAL_PORT_2, -1, 6) #error "SERIAL_PORT_2 must be from -1 to 6" #elif SERIAL_PORT_2 == SERIAL_PORT @@ -125,22 +128,26 @@ #undef pgm_read_ptr #define pgm_read_ptr(addr) (*(addr)) -// -------------------------------------------------------------------------- +// ------------------------ // Types -// -------------------------------------------------------------------------- +// ------------------------ typedef int8_t pin_t; -// -------------------------------------------------------------------------- +#ifdef STM32F4 + #define HAL_SERVO_LIB libServo +#endif + +// ------------------------ // Public Variables -// -------------------------------------------------------------------------- +// ------------------------ /** result of last ADC conversion */ extern uint16_t HAL_adc_result; -// -------------------------------------------------------------------------- +// ------------------------ // Public functions -// -------------------------------------------------------------------------- +// ------------------------ // Memory related #define __bss_end __bss_end__ @@ -162,6 +169,7 @@ extern "C" { */ extern "C" char* _sbrk(int incr); + /* static int freeMemory() { volatile int top; @@ -169,12 +177,16 @@ static int freeMemory() { return top; } */ + static int freeMemory() { volatile char top; return &top - reinterpret_cast(_sbrk(0)); } +// // SPI: Extended functions which take a channel number (hardware SPI only) +// + /** Write single byte to specified SPI channel */ void spiSend(uint32_t chan, byte b); /** Write buffer to specified SPI channel */ @@ -182,19 +194,22 @@ void spiSend(uint32_t chan, const uint8_t* buf, size_t n); /** Read single byte from specified SPI channel */ uint8_t spiRec(uint32_t chan); - +// // EEPROM +// /** - * TODO: Write all this eeprom stuff. Can emulate eeprom in flash as last resort. - * Wire library should work for i2c eeproms. + * TODO: Write all this EEPROM stuff. Can emulate EEPROM in flash as last resort. + * Wire library should work for i2c EEPROMs. */ void eeprom_write_byte(uint8_t *pos, unsigned char value); uint8_t eeprom_read_byte(uint8_t *pos); void eeprom_read_block (void *__dst, const void *__src, size_t __n); void eeprom_update_block (const void *__src, void *__dst, size_t __n); +// // ADC +// #define HAL_ANALOG_SELECT(pin) pinMode(pin, INPUT) @@ -210,3 +225,8 @@ uint16_t HAL_adc_get_result(void); #define GET_PIN_MAP_PIN(index) index #define GET_PIN_MAP_INDEX(pin) pin #define PARSED_PIN_INDEX(code, dval) parser.intval(code, dval) + +#ifdef STM32F4 + #define JTAG_DISABLE() afio_cfg_debug_ports(AFIO_DEBUG_SW_ONLY) + #define JTAGSWD_DISABLE() afio_cfg_debug_ports(AFIO_DEBUG_NONE) +#endif diff --git a/Marlin/src/HAL/HAL_STM32F7/HAL_Servo_STM32F7.cpp b/Marlin/src/HAL/HAL_STM32_F4_F7/HAL_Servo_STM32_F4_F7.cpp similarity index 91% rename from Marlin/src/HAL/HAL_STM32F7/HAL_Servo_STM32F7.cpp rename to Marlin/src/HAL/HAL_STM32_F4_F7/HAL_Servo_STM32_F4_F7.cpp index 3be816ad34..5c585e663d 100644 --- a/Marlin/src/HAL/HAL_STM32F7/HAL_Servo_STM32F7.cpp +++ b/Marlin/src/HAL/HAL_STM32_F4_F7/HAL_Servo_STM32_F4_F7.cpp @@ -21,13 +21,13 @@ * */ -#ifdef STM32F7 +#if defined(STM32GENERIC) && (defined(STM32F4) || defined(STM32F7)) #include "../../inc/MarlinConfig.h" #if HAS_SERVOS -#include "HAL_Servo_STM32F7.h" +#include "HAL_Servo_STM32_F4_F7.h" int8_t libServo::attach(const int pin) { if (this->servoIndex >= MAX_SERVOS) return -1; @@ -49,6 +49,6 @@ void libServo::move(const int value) { #endif } } -#endif // HAS_SERVOS -#endif // STM32F7 +#endif // HAS_SERVOS +#endif // STM32GENERIC && (STM32F4 || STM32F7) diff --git a/Marlin/src/HAL/HAL_STM32F4/HAL_Servo_STM32F4.h b/Marlin/src/HAL/HAL_STM32_F4_F7/HAL_Servo_STM32_F4_F7.h similarity index 89% rename from Marlin/src/HAL/HAL_STM32F4/HAL_Servo_STM32F4.h rename to Marlin/src/HAL/HAL_STM32_F4_F7/HAL_Servo_STM32_F4_F7.h index 413c4995a5..c839c6a145 100644 --- a/Marlin/src/HAL/HAL_STM32F4/HAL_Servo_STM32F4.h +++ b/Marlin/src/HAL/HAL_STM32_F4_F7/HAL_Servo_STM32_F4_F7.h @@ -22,7 +22,11 @@ */ #pragma once -#include +//#ifdef STM32F7 +// #include <../../libraries/Servo/src/Servo.h> +//#else + #include +//#endif // Inherit and expand on the official library class libServo : public Servo { @@ -31,7 +35,6 @@ class libServo : public Servo { int8_t attach(const int pin, const int min, const int max); void move(const int value); private: - uint16_t min_ticks; - uint16_t max_ticks; + uint16_t min_ticks, max_ticks; uint8_t servoIndex; // index into the channel data for this servo }; diff --git a/Marlin/src/HAL/HAL_STM32F4/HAL_spi_STM32F4.cpp b/Marlin/src/HAL/HAL_STM32_F4_F7/HAL_spi_STM32_F4_F7.cpp similarity index 79% rename from Marlin/src/HAL/HAL_STM32F4/HAL_spi_STM32F4.cpp rename to Marlin/src/HAL/HAL_STM32_F4_F7/HAL_spi_STM32_F4_F7.cpp index 315995c016..ca7cc5b543 100644 --- a/Marlin/src/HAL/HAL_STM32F4/HAL_spi_STM32F4.cpp +++ b/Marlin/src/HAL/HAL_STM32_F4_F7/HAL_spi_STM32_F4_F7.cpp @@ -27,14 +27,10 @@ */ /** - * Adapted to the STM32F4 HAL + * Adapted to the Marlin STM32F4/7 HAL */ -#if defined(STM32GENERIC) && defined(STM32F4) - -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- +#if defined(STM32GENERIC) && (defined(STM32F4) || defined(STM32F7)) #include "HAL.h" #include "../shared/HAL_SPI.h" @@ -43,28 +39,26 @@ #include "../../core/macros.h" #include -// -------------------------------------------------------------------------- +// ------------------------ // Public Variables -// -------------------------------------------------------------------------- +// ------------------------ static SPISettings spiConfig; -// -------------------------------------------------------------------------- +// ------------------------ // Public functions -// -------------------------------------------------------------------------- +// ------------------------ #if ENABLED(SOFTWARE_SPI) - - // -------------------------------------------------------------------------- + // ------------------------ // Software SPI - // -------------------------------------------------------------------------- - #error "Software SPI not supported for STM32F4. Use hardware SPI." - + // ------------------------ + #error "Software SPI not supported for STM32F4/7. Use Hardware SPI." #else -// -------------------------------------------------------------------------- +// ------------------------ // Hardware SPI -// -------------------------------------------------------------------------- +// ------------------------ /** * VGPV SPI speed start and F_CPU/2, by default 72/2 = 36Mhz @@ -127,13 +121,11 @@ uint8_t spiRec(void) { */ void spiRead(uint8_t* buf, uint16_t nbyte) { SPI.beginTransaction(spiConfig); - #ifdef STM32GENERIC SPI.dmaTransfer(0, const_cast(buf), nbyte); #else SPI.transfer((uint8_t*)buf, nbyte); #endif - SPI.endTransaction(); } @@ -161,16 +153,13 @@ void spiSend(uint8_t b) { void spiSendBlock(uint8_t token, const uint8_t* buf) { SPI.beginTransaction(spiConfig); SPI.transfer(token); - #ifdef STM32GENERIC SPI.dmaSend(const_cast(buf), 512); #else SPI.transfer((uint8_t*)buf, nullptr, 512); #endif - SPI.endTransaction(); } #endif // SOFTWARE_SPI - -#endif // STM32GENERIC && STM32F4 +#endif // STM32GENERIC && (STM32F4 || STM32F7) diff --git a/Marlin/src/HAL/HAL_STM32_F4_F7/HAL_timers_STM32_F4_F7.h b/Marlin/src/HAL/HAL_STM32_F4_F7/HAL_timers_STM32_F4_F7.h new file mode 100644 index 0000000000..e7fcd6c7c6 --- /dev/null +++ b/Marlin/src/HAL/HAL_STM32_F4_F7/HAL_timers_STM32_F4_F7.h @@ -0,0 +1,28 @@ +/** + * Marlin 3D Printer Firmware + * + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * Copyright (c) 2016 Bob Cousins bobcousins42@googlemail.com + * Copyright (c) 2017 Victor Perez + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +#ifdef STM32F4 + #include "STM32F4/HAL_timers_STM32F4.h" +#else + #include "STM32F7/HAL_timers_STM32F7.h" +#endif diff --git a/Marlin/src/HAL/HAL_STM32_F4_F7/README.md b/Marlin/src/HAL/HAL_STM32_F4_F7/README.md new file mode 100644 index 0000000000..3b5a9ab02e --- /dev/null +++ b/Marlin/src/HAL/HAL_STM32_F4_F7/README.md @@ -0,0 +1,6 @@ +# This HAL is for... + + - STM32F407 MCU with STM32Generic Arduino core by danieleff. + - STM32F765 board "The Borg" with STM32Generic. + +See the `README.md` files in HAL_STM32F4 and HAL_STM32F7 for the specifics of those hals. diff --git a/Marlin/src/HAL/HAL_STM32F4/HAL_timers_STM32F4.cpp b/Marlin/src/HAL/HAL_STM32_F4_F7/STM32F4/HAL_timers_STM32F4.cpp similarity index 75% rename from Marlin/src/HAL/HAL_STM32F4/HAL_timers_STM32F4.cpp rename to Marlin/src/HAL/HAL_STM32_F4_F7/STM32F4/HAL_timers_STM32F4.cpp index 8f1d2603ee..45ea7fc984 100644 --- a/Marlin/src/HAL/HAL_STM32F4/HAL_timers_STM32F4.cpp +++ b/Marlin/src/HAL/HAL_STM32_F4_F7/STM32F4/HAL_timers_STM32F4.cpp @@ -22,52 +22,26 @@ #if defined(STM32GENERIC) && defined(STM32F4) -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - -#include "HAL.h" - +#include "../HAL.h" #include "HAL_timers_STM32F4.h" -// -------------------------------------------------------------------------- -// Externals -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- +// ------------------------ // Local defines -// -------------------------------------------------------------------------- +// ------------------------ #define NUM_HARDWARE_TIMERS 2 #define STEP_TIMER_IRQ_ID TIM5_IRQn #define TEMP_TIMER_IRQ_ID TIM7_IRQn -//#define PRESCALER 1 -// -------------------------------------------------------------------------- -// Types -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Public Variables -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- +// ------------------------ // Private Variables -// -------------------------------------------------------------------------- +// ------------------------ -stm32f4_timer_t TimerHandle[NUM_HARDWARE_TIMERS]; +stm32_timer_t TimerHandle[NUM_HARDWARE_TIMERS]; -// -------------------------------------------------------------------------- -// Function prototypes -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Private functions -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- +// ------------------------ // Public functions -// -------------------------------------------------------------------------- +// ------------------------ bool timers_initialized[NUM_HARDWARE_TIMERS] = {false}; diff --git a/Marlin/src/HAL/HAL_STM32F4/HAL_timers_STM32F4.h b/Marlin/src/HAL/HAL_STM32_F4_F7/STM32F4/HAL_timers_STM32F4.h similarity index 82% rename from Marlin/src/HAL/HAL_STM32F4/HAL_timers_STM32F4.h rename to Marlin/src/HAL/HAL_STM32_F4_F7/STM32F4/HAL_timers_STM32F4.h index 30161bfc4c..726207fbcf 100644 --- a/Marlin/src/HAL/HAL_STM32F4/HAL_timers_STM32F4.h +++ b/Marlin/src/HAL/HAL_STM32_F4_F7/STM32F4/HAL_timers_STM32F4.h @@ -21,15 +21,11 @@ */ #pragma once -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - #include -// -------------------------------------------------------------------------- +// ------------------------ // Defines -// -------------------------------------------------------------------------- +// ------------------------ #define FORCE_INLINE __attribute__((always_inline)) inline @@ -75,29 +71,29 @@ #endif -// -------------------------------------------------------------------------- +// ------------------------ // Types -// -------------------------------------------------------------------------- +// ------------------------ #ifdef STM32GENERIC typedef struct { TIM_HandleTypeDef handle; uint32_t callback; } tTimerConfig; - typedef tTimerConfig stm32f4_timer_t; + typedef tTimerConfig stm32_timer_t; #else - typedef stimer_t stm32f4_timer_t; + typedef stimer_t stm32_timer_t; #endif -// -------------------------------------------------------------------------- +// ------------------------ // Public Variables -// -------------------------------------------------------------------------- +// ------------------------ -extern stm32f4_timer_t TimerHandle[]; +extern stm32_timer_t TimerHandle[]; -// -------------------------------------------------------------------------- +// ------------------------ // Public functions -// -------------------------------------------------------------------------- +// ------------------------ void HAL_timer_start(const uint8_t timer_num, const uint32_t frequency); void HAL_timer_enable_interrupt(const uint8_t timer_num); diff --git a/Marlin/src/HAL/HAL_STM32F4/README.md b/Marlin/src/HAL/HAL_STM32_F4_F7/STM32F4/README.md similarity index 100% rename from Marlin/src/HAL/HAL_STM32F4/README.md rename to Marlin/src/HAL/HAL_STM32_F4_F7/STM32F4/README.md diff --git a/Marlin/src/HAL/HAL_STM32F7/HAL_timers_STM32F7.cpp b/Marlin/src/HAL/HAL_STM32_F4_F7/STM32F7/HAL_timers_STM32F7.cpp similarity index 72% rename from Marlin/src/HAL/HAL_STM32F7/HAL_timers_STM32F7.cpp rename to Marlin/src/HAL/HAL_STM32_F4_F7/STM32F7/HAL_timers_STM32F7.cpp index df4d9c07d2..8da2fc0cfa 100644 --- a/Marlin/src/HAL/HAL_STM32F7/HAL_timers_STM32F7.cpp +++ b/Marlin/src/HAL/HAL_STM32_F4_F7/STM32F7/HAL_timers_STM32F7.cpp @@ -20,56 +20,30 @@ * */ -#ifdef STM32F7 - -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - -#include "HAL.h" +#if defined(STM32GENERIC) && defined(STM32F7) +#include "../HAL.h" #include "HAL_timers_STM32F7.h" -// -------------------------------------------------------------------------- -// Externals -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- +// ------------------------ // Local defines -// -------------------------------------------------------------------------- +// ------------------------ #define NUM_HARDWARE_TIMERS 2 //#define PRESCALER 1 -// -------------------------------------------------------------------------- -// Types -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Public Variables -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- +// ------------------------ // Private Variables -// -------------------------------------------------------------------------- +// ------------------------ tTimerConfig timerConfig[NUM_HARDWARE_TIMERS]; -// -------------------------------------------------------------------------- -// Function prototypes -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Private functions -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- +// ------------------------ // Public functions -// -------------------------------------------------------------------------- +// ------------------------ - -bool timers_initialized[NUM_HARDWARE_TIMERS] = {false}; +bool timers_initialized[NUM_HARDWARE_TIMERS] = { false }; void HAL_timer_start(const uint8_t timer_num, const uint32_t frequency) { @@ -153,4 +127,4 @@ bool HAL_timer_interrupt_enabled(const uint8_t timer_num) { return NVIC->ISER[IRQ_Id >> 5] & _BV32(IRQ_Id & 0x1F); } -#endif // STM32F7 +#endif // STM32GENERIC && STM32F7 diff --git a/Marlin/src/HAL/HAL_STM32F7/HAL_timers_STM32F7.h b/Marlin/src/HAL/HAL_STM32_F4_F7/STM32F7/HAL_timers_STM32F7.h similarity index 81% rename from Marlin/src/HAL/HAL_STM32F7/HAL_timers_STM32F7.h rename to Marlin/src/HAL/HAL_STM32_F4_F7/STM32F7/HAL_timers_STM32F7.h index 01fb02d178..38ecde30bb 100644 --- a/Marlin/src/HAL/HAL_STM32F7/HAL_timers_STM32F7.h +++ b/Marlin/src/HAL/HAL_STM32_F4_F7/STM32F7/HAL_timers_STM32F7.h @@ -21,15 +21,11 @@ */ #pragma once -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - #include -// -------------------------------------------------------------------------- +// ------------------------ // Defines -// -------------------------------------------------------------------------- +// ------------------------ #define FORCE_INLINE __attribute__((always_inline)) inline @@ -61,17 +57,17 @@ #define STEPPER_ISR_ENABLED() HAL_timer_interrupt_enabled(STEP_TIMER_NUM) #define TEMP_ISR_ENABLED() HAL_timer_interrupt_enabled(TEMP_TIMER_NUM) -// TODO change this +// TODO change this extern void TC5_Handler(); extern void TC7_Handler(); #define HAL_STEP_TIMER_ISR() void TC5_Handler() #define HAL_TEMP_TIMER_ISR() void TC7_Handler() -// -------------------------------------------------------------------------- +// ------------------------ // Types -// -------------------------------------------------------------------------- +// ------------------------ typedef struct { TIM_HandleTypeDef timerdef; @@ -79,15 +75,15 @@ typedef struct { uint32_t callback; } tTimerConfig; -// -------------------------------------------------------------------------- +// ------------------------ // Public Variables -// -------------------------------------------------------------------------- +// ------------------------ //extern const tTimerConfig timerConfig[]; -// -------------------------------------------------------------------------- +// ------------------------ // Public functions -// -------------------------------------------------------------------------- +// ------------------------ void HAL_timer_start(const uint8_t timer_num, const uint32_t frequency); void HAL_timer_enable_interrupt(const uint8_t timer_num); diff --git a/Marlin/src/HAL/HAL_STM32F7/README.md b/Marlin/src/HAL/HAL_STM32_F4_F7/STM32F7/README.md similarity index 75% rename from Marlin/src/HAL/HAL_STM32F7/README.md rename to Marlin/src/HAL/HAL_STM32_F4_F7/STM32F7/README.md index 2fb39bf25a..23155b425e 100644 --- a/Marlin/src/HAL/HAL_STM32F7/README.md +++ b/Marlin/src/HAL/HAL_STM32_F4_F7/STM32F7/README.md @@ -4,7 +4,7 @@ https://github.com/danieleff/STM32GENERIC -but i have not committed the changes needed for the Borg there yet, so please use: +but I haven't committed the changes needed for the Borg there yet, so please use: https://github.com/Spawn32/STM32GENERIC @@ -15,9 +15,9 @@ Download the latest GNU ARM Embedded Toolchain: https://developer.arm.com/open-source/gnu-toolchain/gnu-rm/downloads -(The one in Arduino dosen't support STM32F7). +(The one in Arduino doesn't support STM32F7). -Change compiler.path in platform.txt to point to that you downloaded. +Change compiler.path in platform.txt to point to the one you downloaded. # This HAL is in development. # Currently only tested on "The Borg". @@ -25,4 +25,3 @@ Change compiler.path in platform.txt to point to that you downloaded. You will also need the latest Arduino 1.9.0-beta or newer. This HAL is a modified version of Chris Barr's Picoprint STM32F4 HAL, so shouldn't be to hard to get it to work on a F4. - diff --git a/Marlin/src/HAL/HAL_STM32F7/TMC2660.cpp b/Marlin/src/HAL/HAL_STM32_F4_F7/STM32F7/TMC2660.cpp similarity index 97% rename from Marlin/src/HAL/HAL_STM32F7/TMC2660.cpp rename to Marlin/src/HAL/HAL_STM32_F4_F7/STM32F7/TMC2660.cpp index 99cadbde16..2f60bf3546 100644 --- a/Marlin/src/HAL/HAL_STM32F7/TMC2660.cpp +++ b/Marlin/src/HAL/HAL_STM32_F4_F7/STM32F7/TMC2660.cpp @@ -25,22 +25,22 @@ * */ -//#include +#if defined(STM32GENERIC) && defined(STM32F7) -#ifdef STM32F7 +#include "../../../inc/MarlinConfigPre.h" + +#if HAS_DRIVER(TMC2660) #include #include #include "TMC2660.h" -#include "HAL.h" -#include "../../core/serial.h" -#include "../../inc/MarlinConfig.h" -#include "../../Marlin.h" -#include "../../module/stepper_indirection.h" -#include "../../module/printcounter.h" -#include "../../libs/duration_t.h" -#include "../../libs/hex_print_routines.h" +#include "../../../inc/MarlinConfig.h" +#include "../../../Marlin.h" +#include "../../../module/stepper_indirection.h" +#include "../../../module/printcounter.h" +#include "../../../libs/duration_t.h" +#include "../../../libs/hex_print_routines.h" //some default values used in initialization #define DEFAULT_MICROSTEPPING_VALUE 32 @@ -630,19 +630,19 @@ uint16_t TMC26XStepper::getCoolStepLowerSgThreshold() { } uint16_t TMC26XStepper::getCoolStepUpperSgThreshold() { - return (uint8_t)((cool_step_register_value & SE_MAX_PATTERN) >> 8) << 5; + return uint8_t((cool_step_register_value & SE_MAX_PATTERN) >> 8) << 5; } uint8_t TMC26XStepper::getCoolStepCurrentIncrementSize() { - return (uint8_t)((cool_step_register_value & CURRENT_DOWN_STEP_SPEED_PATTERN) >> 13); + return uint8_t((cool_step_register_value & CURRENT_DOWN_STEP_SPEED_PATTERN) >> 13); } uint8_t TMC26XStepper::getCoolStepNumberOfSGReadings() { - return (uint8_t)((cool_step_register_value & SE_CURRENT_STEP_WIDTH_PATTERN) >> 5); + return uint8_t((cool_step_register_value & SE_CURRENT_STEP_WIDTH_PATTERN) >> 5); } uint8_t TMC26XStepper::getCoolStepLowerCurrentLimit() { - return (uint8_t)((cool_step_register_value & MINIMUM_CURRENT_FOURTH) >> 15); + return uint8_t((cool_step_register_value & MINIMUM_CURRENT_FOURTH) >> 15); } void TMC26XStepper::setEnabled(boolean enabled) { @@ -895,4 +895,6 @@ inline void TMC26XStepper::send262(uint32_t datagram) { driver_status_result = i_datagram; } -#endif // STM32F7 +#endif // HAS_DRIVER(TMC2660) + +#endif // STM32GENERIC && STM32F7 diff --git a/Marlin/src/HAL/HAL_STM32F7/TMC2660.h b/Marlin/src/HAL/HAL_STM32_F4_F7/STM32F7/TMC2660.h similarity index 99% rename from Marlin/src/HAL/HAL_STM32F7/TMC2660.h rename to Marlin/src/HAL/HAL_STM32_F4_F7/STM32F7/TMC2660.h index 1b44a4d5f5..9753aa3407 100644 --- a/Marlin/src/HAL/HAL_STM32F7/TMC2660.h +++ b/Marlin/src/HAL/HAL_STM32_F4_F7/STM32F7/TMC2660.h @@ -140,7 +140,6 @@ class TMC26XStepper { */ void un_start(); - /*! * \brief Set the rotation speed in RPM. * \param whatSpeed the desired speed in RPM. diff --git a/Marlin/src/HAL/HAL_STM32F7/EEPROM_Emul/eeprom_emul.cpp b/Marlin/src/HAL/HAL_STM32_F4_F7/eeprom_emul.cpp similarity index 74% rename from Marlin/src/HAL/HAL_STM32F7/EEPROM_Emul/eeprom_emul.cpp rename to Marlin/src/HAL/HAL_STM32_F4_F7/eeprom_emul.cpp index 10b3219e9a..f8db99d3f6 100644 --- a/Marlin/src/HAL/HAL_STM32F7/EEPROM_Emul/eeprom_emul.cpp +++ b/Marlin/src/HAL/HAL_STM32_F4_F7/eeprom_emul.cpp @@ -8,8 +8,8 @@ ****************************************************************************** * @attention * - *

© Copyright 2016 STMicroelectronics International N.V. - * All rights reserved.

+ * Copyright © 2016 STMicroelectronics International N.V. + * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted, provided that the following conditions are met: @@ -47,14 +47,11 @@ /** @addtogroup EEPROM_Emulation * @{ */ -#ifdef STM32F7 +#if defined(STM32GENERIC) && (defined(STM32F4) || defined(STM32F7)) /* Includes ------------------------------------------------------------------*/ #include "eeprom_emul.h" -/* Private typedef -----------------------------------------------------------*/ -/* Private define ------------------------------------------------------------*/ -/* Private macro -------------------------------------------------------------*/ /* Private variables ---------------------------------------------------------*/ /* Global variable used to store variable value in read sequence */ @@ -71,7 +68,7 @@ static uint16_t EE_VerifyPageFullWriteVariable(uint16_t VirtAddress, uint16_t Da static uint16_t EE_PageTransfer(uint16_t VirtAddress, uint16_t Data); static uint16_t EE_VerifyPageFullyErased(uint32_t Address); -/** + /** * @brief Restore the pages to a known good state in case of page's status * corruption after a power loss. * @param None. @@ -79,76 +76,66 @@ static uint16_t EE_VerifyPageFullyErased(uint32_t Address); * - FLASH_COMPLETE: on success */ uint16_t EE_Initialize(void) { - uint16_t PageStatus0 = 6, PageStatus1 = 6; - uint16_t VarIdx = 0; - uint16_t EepromStatus = 0, ReadStatus = 0; - int16_t x = -1; - HAL_StatusTypeDef FlashStatus; - uint32_t SectorError = 0; + /* Get Page0 and Page1 status */ + uint16_t PageStatus0 = (*(__IO uint16_t*)PAGE0_BASE_ADDRESS), + PageStatus1 = (*(__IO uint16_t*)PAGE1_BASE_ADDRESS); + FLASH_EraseInitTypeDef pEraseInit; - - - /* Get Page0 status */ - PageStatus0 = (*(__IO uint16_t*)PAGE0_BASE_ADDRESS); - /* Get Page1 status */ - PageStatus1 = (*(__IO uint16_t*)PAGE1_BASE_ADDRESS); - pEraseInit.TypeErase = TYPEERASE_SECTORS; pEraseInit.Sector = PAGE0_ID; pEraseInit.NbSectors = 1; pEraseInit.VoltageRange = VOLTAGE_RANGE; /* Check for invalid header states and repair if necessary */ + uint32_t SectorError; switch (PageStatus0) { case ERASED: if (PageStatus1 == VALID_PAGE) { /* Page0 erased, Page1 valid */ - /* Erase Page0 */ + /* Erase Page0 */ if (!EE_VerifyPageFullyErased(PAGE0_BASE_ADDRESS)) { - FlashStatus = HAL_FLASHEx_Erase(&pEraseInit, &SectorError); - /* If erase operation was failed, a Flash error code is returned */ - if (FlashStatus != HAL_OK) return FlashStatus; + /* As the last operation, simply return the result */ + return HAL_FLASHEx_Erase(&pEraseInit, &SectorError); } } else if (PageStatus1 == RECEIVE_DATA) { /* Page0 erased, Page1 receive */ /* Erase Page0 */ if (!EE_VerifyPageFullyErased(PAGE0_BASE_ADDRESS)) { - FlashStatus = HAL_FLASHEx_Erase(&pEraseInit, &SectorError); + HAL_StatusTypeDef fStat = HAL_FLASHEx_Erase(&pEraseInit, &SectorError); /* If erase operation was failed, a Flash error code is returned */ - if (FlashStatus != HAL_OK) return FlashStatus; + if (fStat != HAL_OK) return fStat; } /* Mark Page1 as valid */ - FlashStatus = HAL_FLASH_Program(TYPEPROGRAM_HALFWORD, PAGE1_BASE_ADDRESS, VALID_PAGE); - /* If program operation was failed, a Flash error code is returned */ - if (FlashStatus != HAL_OK) return FlashStatus; + /* As the last operation, simply return the result */ + return HAL_FLASH_Program(TYPEPROGRAM_HALFWORD, PAGE1_BASE_ADDRESS, VALID_PAGE); } else { /* First EEPROM access (Page0&1 are erased) or invalid state -> format EEPROM */ /* Erase both Page0 and Page1 and set Page0 as valid page */ - FlashStatus = EE_Format(); - /* If erase/program operation was failed, a Flash error code is returned */ - if (FlashStatus != HAL_OK) return FlashStatus; + /* As the last operation, simply return the result */ + return EE_Format(); } break; case RECEIVE_DATA: if (PageStatus1 == VALID_PAGE) { /* Page0 receive, Page1 valid */ /* Transfer data from Page1 to Page0 */ - for (VarIdx = 0; VarIdx < NB_OF_VAR; VarIdx++) { + int16_t x = -1; + for (uint16_t VarIdx = 0; VarIdx < NB_OF_VAR; VarIdx++) { if (( *(__IO uint16_t*)(PAGE0_BASE_ADDRESS + 6)) == VirtAddVarTab[VarIdx]) x = VarIdx; if (VarIdx != x) { /* Read the last variables' updates */ - ReadStatus = EE_ReadVariable(VirtAddVarTab[VarIdx], &DataVar); + uint16_t ReadStatus = EE_ReadVariable(VirtAddVarTab[VarIdx], &DataVar); /* In case variable corresponding to the virtual address was found */ if (ReadStatus != 0x1) { /* Transfer the variable to the Page0 */ - EepromStatus = EE_VerifyPageFullWriteVariable(VirtAddVarTab[VarIdx], DataVar); + uint16_t EepromStatus = EE_VerifyPageFullWriteVariable(VirtAddVarTab[VarIdx], DataVar); /* If program operation was failed, a Flash error code is returned */ if (EepromStatus != HAL_OK) return EepromStatus; } } } /* Mark Page0 as valid */ - FlashStatus = HAL_FLASH_Program(TYPEPROGRAM_HALFWORD, PAGE0_BASE_ADDRESS, VALID_PAGE); + HAL_StatusTypeDef FlashStatus = HAL_FLASH_Program(TYPEPROGRAM_HALFWORD, PAGE0_BASE_ADDRESS, VALID_PAGE); /* If program operation was failed, a Flash error code is returned */ if (FlashStatus != HAL_OK) return FlashStatus; pEraseInit.Sector = PAGE1_ID; @@ -156,9 +143,8 @@ uint16_t EE_Initialize(void) { pEraseInit.VoltageRange = VOLTAGE_RANGE; /* Erase Page1 */ if (!EE_VerifyPageFullyErased(PAGE1_BASE_ADDRESS)) { - FlashStatus = HAL_FLASHEx_Erase(&pEraseInit, &SectorError); - /* If erase operation was failed, a Flash error code is returned */ - if (FlashStatus != HAL_OK) return FlashStatus; + /* As the last operation, simply return the result */ + return HAL_FLASHEx_Erase(&pEraseInit, &SectorError); } } else if (PageStatus1 == ERASED) { /* Page0 receive, Page1 erased */ @@ -167,20 +153,18 @@ uint16_t EE_Initialize(void) { pEraseInit.VoltageRange = VOLTAGE_RANGE; /* Erase Page1 */ if (!EE_VerifyPageFullyErased(PAGE1_BASE_ADDRESS)) { - FlashStatus = HAL_FLASHEx_Erase(&pEraseInit, &SectorError); + HAL_StatusTypeDef fStat = HAL_FLASHEx_Erase(&pEraseInit, &SectorError); /* If erase operation was failed, a Flash error code is returned */ - if (FlashStatus != HAL_OK) return FlashStatus; + if (fStat != HAL_OK) return fStat; } /* Mark Page0 as valid */ - FlashStatus = HAL_FLASH_Program(TYPEPROGRAM_HALFWORD, PAGE0_BASE_ADDRESS, VALID_PAGE); - /* If program operation was failed, a Flash error code is returned */ - if (FlashStatus != HAL_OK) return FlashStatus; + /* As the last operation, simply return the result */ + return HAL_FLASH_Program(TYPEPROGRAM_HALFWORD, PAGE0_BASE_ADDRESS, VALID_PAGE); } else { /* Invalid state -> format eeprom */ /* Erase both Page0 and Page1 and set Page0 as valid page */ - FlashStatus = EE_Format(); - /* If erase/program operation was failed, a Flash error code is returned */ - if (FlashStatus != HAL_OK) return FlashStatus; + /* As the last operation, simply return the result */ + return EE_Format(); } break; @@ -204,17 +188,18 @@ uint16_t EE_Initialize(void) { } else { /* Page0 valid, Page1 receive */ /* Transfer data from Page0 to Page1 */ - for (VarIdx = 0; VarIdx < NB_OF_VAR; VarIdx++) { + int16_t x = -1; + for (uint16_t VarIdx = 0; VarIdx < NB_OF_VAR; VarIdx++) { if ((*(__IO uint16_t*)(PAGE1_BASE_ADDRESS + 6)) == VirtAddVarTab[VarIdx]) x = VarIdx; if (VarIdx != x) { /* Read the last variables' updates */ - ReadStatus = EE_ReadVariable(VirtAddVarTab[VarIdx], &DataVar); + uint16_t ReadStatus = EE_ReadVariable(VirtAddVarTab[VarIdx], &DataVar); /* In case variable corresponding to the virtual address was found */ if (ReadStatus != 0x1) { /* Transfer the variable to the Page1 */ - EepromStatus = EE_VerifyPageFullWriteVariable(VirtAddVarTab[VarIdx], DataVar); + uint16_t EepromStatus = EE_VerifyPageFullWriteVariable(VirtAddVarTab[VarIdx], DataVar); /* If program operation was failed, a Flash error code is returned */ if (EepromStatus != HAL_OK) return EepromStatus; } @@ -229,19 +214,16 @@ uint16_t EE_Initialize(void) { pEraseInit.VoltageRange = VOLTAGE_RANGE; /* Erase Page0 */ if (!EE_VerifyPageFullyErased(PAGE0_BASE_ADDRESS)) { - FlashStatus = HAL_FLASHEx_Erase(&pEraseInit, &SectorError); - /* If erase operation was failed, a Flash error code is returned */ - if (FlashStatus != HAL_OK) return FlashStatus; + /* As the last operation, simply return the result */ + return HAL_FLASHEx_Erase(&pEraseInit, &SectorError); } } break; default: /* Any other state -> format eeprom */ /* Erase both Page0 and Page1 and set Page0 as valid page */ - FlashStatus = EE_Format(); - /* If erase/program operation was failed, a Flash error code is returned */ - if (FlashStatus != HAL_OK) return FlashStatus; - break; + /* As the last operation, simply return the result */ + return EE_Format(); } return HAL_OK; @@ -259,11 +241,10 @@ uint16_t EE_Initialize(void) { */ uint16_t EE_VerifyPageFullyErased(uint32_t Address) { uint32_t ReadStatus = 1; - uint16_t AddressValue = 0x5555; /* Check each active page address starting from end */ while (Address <= PAGE0_END_ADDRESS) { /* Get the current location content to be compared with virtual address */ - AddressValue = (*(__IO uint16_t*)Address); + uint16_t AddressValue = (*(__IO uint16_t*)Address); /* Compare the read address with the virtual address */ if (AddressValue != ERASED) { /* In case variable value is read, reset ReadStatus flag */ @@ -288,26 +269,22 @@ uint16_t EE_VerifyPageFullyErased(uint32_t Address) { * - NO_VALID_PAGE: if no valid page was found. */ uint16_t EE_ReadVariable(uint16_t VirtAddress, uint16_t* Data) { - uint16_t ValidPage = PAGE0; - uint16_t AddressValue = 0x5555, ReadStatus = 1; - uint32_t Address = EEPROM_START_ADDRESS, PageStartAddress = EEPROM_START_ADDRESS; + uint16_t ReadStatus = 1; /* Get active Page for read operation */ - ValidPage = EE_FindValidPage(READ_FROM_VALID_PAGE); + uint16_t ValidPage = EE_FindValidPage(READ_FROM_VALID_PAGE); /* Check if there is no valid page */ if (ValidPage == NO_VALID_PAGE) return NO_VALID_PAGE; - /* Get the valid Page start Address */ - PageStartAddress = (uint32_t)(EEPROM_START_ADDRESS + (uint32_t)(ValidPage * PAGE_SIZE)); - - /* Get the valid Page end Address */ - Address = (uint32_t)((EEPROM_START_ADDRESS - 2) + (uint32_t)((1 + ValidPage) * PAGE_SIZE)); + /* Get the valid Page start and end Addresses */ + uint32_t PageStartAddress = uint32_t(EEPROM_START_ADDRESS) + uint32_t(ValidPage * (PAGE_SIZE)), + Address = PageStartAddress + PAGE_SIZE - 2; /* Check each active page address starting from end */ - while (Address > (PageStartAddress + 2)) { + while (Address > PageStartAddress + 2) { /* Get the current location content to be compared with virtual address */ - AddressValue = (*(__IO uint16_t*)Address); + uint16_t AddressValue = (*(__IO uint16_t*)Address); /* Compare the read address with the virtual address */ if (AddressValue == VirtAddress) { @@ -353,16 +330,17 @@ uint16_t EE_WriteVariable(uint16_t VirtAddress, uint16_t Data) { * EEPROM formating */ static HAL_StatusTypeDef EE_Format(void) { - HAL_StatusTypeDef FlashStatus = HAL_OK; - uint32_t SectorError = 0; FLASH_EraseInitTypeDef pEraseInit; - pEraseInit.TypeErase = FLASH_TYPEERASE_SECTORS; pEraseInit.Sector = PAGE0_ID; pEraseInit.NbSectors = 1; pEraseInit.VoltageRange = VOLTAGE_RANGE; + + HAL_StatusTypeDef FlashStatus; // = HAL_OK + /* Erase Page0 */ if (!EE_VerifyPageFullyErased(PAGE0_BASE_ADDRESS)) { + uint32_t SectorError; FlashStatus = HAL_FLASHEx_Erase(&pEraseInit, &SectorError); /* If erase operation was failed, a Flash error code is returned */ if (FlashStatus != HAL_OK) return FlashStatus; @@ -375,9 +353,9 @@ static HAL_StatusTypeDef EE_Format(void) { pEraseInit.Sector = PAGE1_ID; /* Erase Page1 */ if (!EE_VerifyPageFullyErased(PAGE1_BASE_ADDRESS)) { - FlashStatus = HAL_FLASHEx_Erase(&pEraseInit, &SectorError); - /* If erase operation was failed, a Flash error code is returned */ - if (FlashStatus != HAL_OK) return FlashStatus; + /* As the last operation, just return the result code */ + uint32_t SectorError; + return HAL_FLASHEx_Erase(&pEraseInit, &SectorError); } return HAL_OK; @@ -393,26 +371,20 @@ static HAL_StatusTypeDef EE_Format(void) { * of no valid page was found */ static uint16_t EE_FindValidPage(uint8_t Operation) { - uint16_t PageStatus0 = 6, PageStatus1 = 6; - - /* Get Page0 actual status */ - PageStatus0 = (*(__IO uint16_t*)PAGE0_BASE_ADDRESS); - - /* Get Page1 actual status */ - PageStatus1 = (*(__IO uint16_t*)PAGE1_BASE_ADDRESS); + /* Get Page0 and Page1 actual status */ + uint16_t PageStatus0 = (*(__IO uint16_t*)PAGE0_BASE_ADDRESS), + PageStatus1 = (*(__IO uint16_t*)PAGE1_BASE_ADDRESS); /* Write or read operation */ switch (Operation) { case WRITE_IN_VALID_PAGE: /* ---- Write operation ---- */ if (PageStatus1 == VALID_PAGE) { /* Page0 receiving data */ - if (PageStatus0 == RECEIVE_DATA) return PAGE0; /* Page0 valid */ - else return PAGE1; /* Page1 valid */ + return (PageStatus0 == RECEIVE_DATA) ? PAGE0 : PAGE1; } else if (PageStatus0 == VALID_PAGE) { /* Page1 receiving data */ - if (PageStatus1 == RECEIVE_DATA) return PAGE1; /* Page1 valid */ - else return PAGE0; /* Page0 valid */ + return (PageStatus1 == RECEIVE_DATA) ? PAGE1 : PAGE0; } else return NO_VALID_PAGE; /* No valid Page */ @@ -441,34 +413,26 @@ static uint16_t EE_FindValidPage(uint8_t Operation) { * - Flash error code: on write Flash error */ static uint16_t EE_VerifyPageFullWriteVariable(uint16_t VirtAddress, uint16_t Data) { - HAL_StatusTypeDef FlashStatus = HAL_OK; - uint16_t ValidPage = PAGE0; - uint32_t Address = EEPROM_START_ADDRESS, PageEndAddress = EEPROM_START_ADDRESS+PAGE_SIZE; - /* Get valid Page for write operation */ - ValidPage = EE_FindValidPage(WRITE_IN_VALID_PAGE); + uint16_t ValidPage = EE_FindValidPage(WRITE_IN_VALID_PAGE); /* Check if there is no valid page */ if (ValidPage == NO_VALID_PAGE) return NO_VALID_PAGE; - /* Get the valid Page start Address */ - Address = (uint32_t)(EEPROM_START_ADDRESS + (uint32_t)(ValidPage * PAGE_SIZE)); - - /* Get the valid Page end Address */ - PageEndAddress = (uint32_t)((EEPROM_START_ADDRESS - 1) + (uint32_t)((ValidPage + 1) * PAGE_SIZE)); + /* Get the valid Page start and end Addresses */ + uint32_t Address = uint32_t(EEPROM_START_ADDRESS) + uint32_t(ValidPage * (PAGE_SIZE)), + PageEndAddress = Address + PAGE_SIZE - 1; /* Check each active page address starting from begining */ while (Address < PageEndAddress) { /* Verify if Address and Address+2 contents are 0xFFFFFFFF */ if ((*(__IO uint32_t*)Address) == 0xFFFFFFFF) { /* Set variable data */ - FlashStatus = HAL_FLASH_Program(TYPEPROGRAM_HALFWORD, Address, Data); + HAL_StatusTypeDef FlashStatus = HAL_FLASH_Program(TYPEPROGRAM_HALFWORD, Address, Data); /* If program operation was failed, a Flash error code is returned */ if (FlashStatus != HAL_OK) return FlashStatus; - /* Set variable virtual address */ - FlashStatus = HAL_FLASH_Program(TYPEPROGRAM_HALFWORD, Address + 2, VirtAddress); - /* Return program operation status */ - return FlashStatus; + /* Set variable virtual address, return status */ + return HAL_FLASH_Program(TYPEPROGRAM_HALFWORD, Address + 2, VirtAddress); } else /* Next address location */ Address += 4; @@ -490,16 +454,10 @@ static uint16_t EE_VerifyPageFullWriteVariable(uint16_t VirtAddress, uint16_t Da * - Flash error code: on write Flash error */ static uint16_t EE_PageTransfer(uint16_t VirtAddress, uint16_t Data) { - HAL_StatusTypeDef FlashStatus = HAL_OK; - uint32_t NewPageAddress = EEPROM_START_ADDRESS; - uint16_t OldPageId=0; - uint16_t ValidPage = PAGE0, VarIdx = 0; - uint16_t EepromStatus = 0, ReadStatus = 0; - uint32_t SectorError = 0; - FLASH_EraseInitTypeDef pEraseInit; - /* Get active Page for read operation */ - ValidPage = EE_FindValidPage(READ_FROM_VALID_PAGE); + uint16_t ValidPage = EE_FindValidPage(READ_FROM_VALID_PAGE); + uint32_t NewPageAddress = EEPROM_START_ADDRESS; + uint16_t OldPageId = 0; if (ValidPage == PAGE1) { /* Page1 valid */ /* New page address where variable will be moved to */ @@ -517,20 +475,20 @@ static uint16_t EE_PageTransfer(uint16_t VirtAddress, uint16_t Data) { return NO_VALID_PAGE; /* No valid Page */ /* Set the new Page status to RECEIVE_DATA status */ - FlashStatus = HAL_FLASH_Program(TYPEPROGRAM_HALFWORD, NewPageAddress, RECEIVE_DATA); + HAL_StatusTypeDef FlashStatus = HAL_FLASH_Program(TYPEPROGRAM_HALFWORD, NewPageAddress, RECEIVE_DATA); /* If program operation was failed, a Flash error code is returned */ if (FlashStatus != HAL_OK) return FlashStatus; /* Write the variable passed as parameter in the new active page */ - EepromStatus = EE_VerifyPageFullWriteVariable(VirtAddress, Data); + uint16_t EepromStatus = EE_VerifyPageFullWriteVariable(VirtAddress, Data); /* If program operation was failed, a Flash error code is returned */ if (EepromStatus != HAL_OK) return EepromStatus; /* Transfer process: transfer variables from old to the new active page */ - for (VarIdx = 0; VarIdx < NB_OF_VAR; VarIdx++) { + for (uint16_t VarIdx = 0; VarIdx < NB_OF_VAR; VarIdx++) { if (VirtAddVarTab[VarIdx] != VirtAddress) { /* Check each variable except the one passed as parameter */ /* Read the other last variable updates */ - ReadStatus = EE_ReadVariable(VirtAddVarTab[VarIdx], &DataVar); + uint16_t ReadStatus = EE_ReadVariable(VirtAddVarTab[VarIdx], &DataVar); /* In case variable corresponding to the virtual address was found */ if (ReadStatus != 0x1) { /* Transfer the variable to the new active page */ @@ -541,26 +499,24 @@ static uint16_t EE_PageTransfer(uint16_t VirtAddress, uint16_t Data) { } } + FLASH_EraseInitTypeDef pEraseInit; pEraseInit.TypeErase = TYPEERASE_SECTORS; pEraseInit.Sector = OldPageId; pEraseInit.NbSectors = 1; pEraseInit.VoltageRange = VOLTAGE_RANGE; /* Erase the old Page: Set old Page status to ERASED status */ + uint32_t SectorError; FlashStatus = HAL_FLASHEx_Erase(&pEraseInit, &SectorError); /* If erase operation was failed, a Flash error code is returned */ if (FlashStatus != HAL_OK) return FlashStatus; /* Set new Page status to VALID_PAGE status */ - FlashStatus = HAL_FLASH_Program(TYPEPROGRAM_HALFWORD, NewPageAddress, VALID_PAGE); - /* If program operation was failed, a Flash error code is returned */ - if (FlashStatus != HAL_OK) return FlashStatus; - - /* Return last operation flash status */ - return FlashStatus; + /* As the last operation, just return the result code */ + return HAL_FLASH_Program(TYPEPROGRAM_HALFWORD, NewPageAddress, VALID_PAGE); } -#endif // STM32F7 +#endif // STM32GENERIC && (STM32F4 || STM32F7) /** * @} diff --git a/Marlin/src/HAL/HAL_STM32F4/EEPROM_Emul/eeprom_emul.h b/Marlin/src/HAL/HAL_STM32_F4_F7/eeprom_emul.h similarity index 64% rename from Marlin/src/HAL/HAL_STM32F4/EEPROM_Emul/eeprom_emul.h rename to Marlin/src/HAL/HAL_STM32_F4_F7/eeprom_emul.h index fe0da6387b..90aeeee5a3 100644 --- a/Marlin/src/HAL/HAL_STM32F4/EEPROM_Emul/eeprom_emul.h +++ b/Marlin/src/HAL/HAL_STM32_F4_F7/eeprom_emul.h @@ -8,7 +8,7 @@ ****************************************************************************** * @attention * - *

© Copyright � 2016 STMicroelectronics International N.V. + * Copyright © 2016 STMicroelectronics International N.V. * All rights reserved.

* * Redistribution and use in source and binary forms, with or without @@ -45,63 +45,68 @@ ******************************************************************************/ #pragma once -// -------------------------------------------------------------------------- +// ------------------------ // Includes -// -------------------------------------------------------------------------- -#include "../../../inc/MarlinConfig.h" -#include "../HAL.h" +// ------------------------ + +#include "../../inc/MarlinConfig.h" +#include "HAL.h" /* Exported constants --------------------------------------------------------*/ /* EEPROM emulation firmware error codes */ -#define EE_OK (uint32_t)HAL_OK -#define EE_ERROR (uint32_t)HAL_ERROR -#define EE_BUSY (uint32_t)HAL_BUSY -#define EE_TIMEOUT (uint32_t)HAL_TIMEOUT +#define EE_OK uint32_t(HAL_OK) +#define EE_ERROR uint32_t(HAL_ERROR) +#define EE_BUSY uint32_t(HAL_BUSY) +#define EE_TIMEOUT uint32_t(HAL_TIMEOUT) /* Define the size of the sectors to be used */ -#define PAGE_SIZE (uint32_t)0x4000 /* Page size = 16KByte */ +#define PAGE_SIZE uint32_t(0x4000) /* Page size = 16KByte */ /* Device voltage range supposed to be [2.7V to 3.6V], the operation will be done by word */ -#define VOLTAGE_RANGE (uint8_t)VOLTAGE_RANGE_3 +#define VOLTAGE_RANGE uint8_t(VOLTAGE_RANGE_3) /* EEPROM start address in Flash */ -#define EEPROM_START_ADDRESS ((uint32_t)0x08078000) /* EEPROM emulation start address: - after 480KByte of used Flash memory */ +#ifdef STM32F7 + #define EEPROM_START_ADDRESS uint32_t(0x08100000) /* EEPROM emulation start address: + from sector2 : after 16KByte of used + Flash memory */ +#else + #define EEPROM_START_ADDRESS uint32_t(0x08078000) /* EEPROM emulation start address: + after 480KByte of used Flash memory */ +#endif /* Pages 0 and 1 base and end addresses */ -#define PAGE0_BASE_ADDRESS ((uint32_t)(EEPROM_START_ADDRESS + 0x0000)) -#define PAGE0_END_ADDRESS ((uint32_t)(EEPROM_START_ADDRESS + (PAGE_SIZE - 1))) -#define PAGE0_ID FLASH_SECTOR_1 +#define PAGE0_BASE_ADDRESS uint32_t(EEPROM_START_ADDRESS + 0x0000) +#define PAGE0_END_ADDRESS uint32_t(EEPROM_START_ADDRESS + PAGE_SIZE - 1) +#define PAGE0_ID FLASH_SECTOR_1 -#define PAGE1_BASE_ADDRESS ((uint32_t)(EEPROM_START_ADDRESS + 0x4000)) -#define PAGE1_END_ADDRESS ((uint32_t)(EEPROM_START_ADDRESS + (2 * PAGE_SIZE - 1))) -#define PAGE1_ID FLASH_SECTOR_2 +#define PAGE1_BASE_ADDRESS uint32_t(EEPROM_START_ADDRESS + 0x4000) +#define PAGE1_END_ADDRESS uint32_t(EEPROM_START_ADDRESS + 2 * (PAGE_SIZE) - 1) +#define PAGE1_ID FLASH_SECTOR_2 /* Used Flash pages for EEPROM emulation */ -#define PAGE0 ((uint16_t)0x0000) -#define PAGE1 ((uint16_t)0x0001) /* Page nb between PAGE0_BASE_ADDRESS & PAGE1_BASE_ADDRESS*/ +#define PAGE0 uint16_t(0x0000) +#define PAGE1 uint16_t(0x0001) /* Page nb between PAGE0_BASE_ADDRESS & PAGE1_BASE_ADDRESS*/ /* No valid page define */ -#define NO_VALID_PAGE ((uint16_t)0x00AB) +#define NO_VALID_PAGE uint16_t(0x00AB) /* Page status definitions */ -#define ERASED ((uint16_t)0xFFFF) /* Page is empty */ -#define RECEIVE_DATA ((uint16_t)0xEEEE) /* Page is marked to receive data */ -#define VALID_PAGE ((uint16_t)0x0000) /* Page containing valid data */ +#define ERASED uint16_t(0xFFFF) /* Page is empty */ +#define RECEIVE_DATA uint16_t(0xEEEE) /* Page is marked to receive data */ +#define VALID_PAGE uint16_t(0x0000) /* Page containing valid data */ /* Valid pages in read and write defines */ -#define READ_FROM_VALID_PAGE ((uint8_t)0x00) -#define WRITE_IN_VALID_PAGE ((uint8_t)0x01) +#define READ_FROM_VALID_PAGE uint8_t(0x00) +#define WRITE_IN_VALID_PAGE uint8_t(0x01) /* Page full define */ -#define PAGE_FULL ((uint8_t)0x80) +#define PAGE_FULL uint8_t(0x80) /* Variables' number */ -#define NB_OF_VAR ((uint16_t)4096) +#define NB_OF_VAR uint16_t(4096) -/* Exported types ------------------------------------------------------------*/ -/* Exported macro ------------------------------------------------------------*/ /* Exported functions ------------------------------------------------------- */ uint16_t EE_Initialize(void); uint16_t EE_ReadVariable(uint16_t VirtAddress, uint16_t* Data); diff --git a/Marlin/src/HAL/HAL_STM32F4/endstop_interrupts.h b/Marlin/src/HAL/HAL_STM32_F4_F7/endstop_interrupts.h similarity index 100% rename from Marlin/src/HAL/HAL_STM32F4/endstop_interrupts.h rename to Marlin/src/HAL/HAL_STM32_F4_F7/endstop_interrupts.h diff --git a/Marlin/src/HAL/HAL_STM32F7/fastio_STM32F7.h b/Marlin/src/HAL/HAL_STM32_F4_F7/fastio_STM32_F4_F7.h similarity index 79% rename from Marlin/src/HAL/HAL_STM32F7/fastio_STM32F7.h rename to Marlin/src/HAL/HAL_STM32_F4_F7/fastio_STM32_F4_F7.h index 81f363609f..4071666060 100644 --- a/Marlin/src/HAL/HAL_STM32F7/fastio_STM32F7.h +++ b/Marlin/src/HAL/HAL_STM32_F4_F7/fastio_STM32_F4_F7.h @@ -23,7 +23,7 @@ #pragma once /** - * Fast I/O interfaces for STM32F7 + * Fast I/O interfaces for STM32F4/7 * These use GPIO functions instead of Direct Port Manipulation, as on AVR. */ @@ -63,10 +63,8 @@ #define PORTC 2 #define PORTD 3 #define PORTE 4 -#define PORTF 5 -#define PORTG 6 -#define _STM32_PIN(_PORT,_PIN) ((PORT##_PORT * 16) + _PIN) +#define _STM32_PIN(P,PN) ((PORT##P * 16) + PN) #define PA0 _STM32_PIN(A, 0) #define PA1 _STM32_PIN(A, 1) @@ -153,36 +151,42 @@ #define PE14 _STM32_PIN(E, 14) #define PE15 _STM32_PIN(E, 15) -#define PF0 _STM32_PIN(F, 0) -#define PF1 _STM32_PIN(F, 1) -#define PF2 _STM32_PIN(F, 2) -#define PF3 _STM32_PIN(F, 3) -#define PF4 _STM32_PIN(F, 4) -#define PF5 _STM32_PIN(F, 5) -#define PF6 _STM32_PIN(F, 6) -#define PF7 _STM32_PIN(F, 7) -#define PF8 _STM32_PIN(F, 8) -#define PF9 _STM32_PIN(F, 9) -#define PF10 _STM32_PIN(F, 10) -#define PF11 _STM32_PIN(F, 11) -#define PF12 _STM32_PIN(F, 12) -#define PF13 _STM32_PIN(F, 13) -#define PF14 _STM32_PIN(F, 14) -#define PF15 _STM32_PIN(F, 15) +#ifdef STM32F7 + #define PORTF 5 + #define PORTG 6 -#define PG0 _STM32_PIN(G, 0) -#define PG1 _STM32_PIN(G, 1) -#define PG2 _STM32_PIN(G, 2) -#define PG3 _STM32_PIN(G, 3) -#define PG4 _STM32_PIN(G, 4) -#define PG5 _STM32_PIN(G, 5) -#define PG6 _STM32_PIN(G, 6) -#define PG7 _STM32_PIN(G, 7) -#define PG8 _STM32_PIN(G, 8) -#define PG9 _STM32_PIN(G, 9) -#define PG10 _STM32_PIN(G, 10) -#define PG11 _STM32_PIN(G, 11) -#define PG12 _STM32_PIN(G, 12) -#define PG13 _STM32_PIN(G, 13) -#define PG14 _STM32_PIN(G, 14) -#define PG15 _STM32_PIN(G, 15) + #define PF0 _STM32_PIN(F, 0) + #define PF1 _STM32_PIN(F, 1) + #define PF2 _STM32_PIN(F, 2) + #define PF3 _STM32_PIN(F, 3) + #define PF4 _STM32_PIN(F, 4) + #define PF5 _STM32_PIN(F, 5) + #define PF6 _STM32_PIN(F, 6) + #define PF7 _STM32_PIN(F, 7) + #define PF8 _STM32_PIN(F, 8) + #define PF9 _STM32_PIN(F, 9) + #define PF10 _STM32_PIN(F, 10) + #define PF11 _STM32_PIN(F, 11) + #define PF12 _STM32_PIN(F, 12) + #define PF13 _STM32_PIN(F, 13) + #define PF14 _STM32_PIN(F, 14) + #define PF15 _STM32_PIN(F, 15) + + #define PG0 _STM32_PIN(G, 0) + #define PG1 _STM32_PIN(G, 1) + #define PG2 _STM32_PIN(G, 2) + #define PG3 _STM32_PIN(G, 3) + #define PG4 _STM32_PIN(G, 4) + #define PG5 _STM32_PIN(G, 5) + #define PG6 _STM32_PIN(G, 6) + #define PG7 _STM32_PIN(G, 7) + #define PG8 _STM32_PIN(G, 8) + #define PG9 _STM32_PIN(G, 9) + #define PG10 _STM32_PIN(G, 10) + #define PG11 _STM32_PIN(G, 11) + #define PG12 _STM32_PIN(G, 12) + #define PG13 _STM32_PIN(G, 13) + #define PG14 _STM32_PIN(G, 14) + #define PG15 _STM32_PIN(G, 15) + +#endif // STM32GENERIC && STM32F7 diff --git a/Marlin/src/HAL/HAL_STM32_F4_F7/inc/Conditionals_LCD.h b/Marlin/src/HAL/HAL_STM32_F4_F7/inc/Conditionals_LCD.h new file mode 100644 index 0000000000..85f26f4016 --- /dev/null +++ b/Marlin/src/HAL/HAL_STM32_F4_F7/inc/Conditionals_LCD.h @@ -0,0 +1,22 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once diff --git a/Marlin/src/HAL/HAL_STM32_F4_F7/inc/Conditionals_adv.h b/Marlin/src/HAL/HAL_STM32_F4_F7/inc/Conditionals_adv.h new file mode 100644 index 0000000000..85f26f4016 --- /dev/null +++ b/Marlin/src/HAL/HAL_STM32_F4_F7/inc/Conditionals_adv.h @@ -0,0 +1,22 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once diff --git a/Marlin/src/HAL/HAL_STM32_F4_F7/inc/Conditionals_post.h b/Marlin/src/HAL/HAL_STM32_F4_F7/inc/Conditionals_post.h new file mode 100644 index 0000000000..85f26f4016 --- /dev/null +++ b/Marlin/src/HAL/HAL_STM32_F4_F7/inc/Conditionals_post.h @@ -0,0 +1,22 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once diff --git a/Marlin/src/HAL/HAL_STM32F7/SanityCheck.h b/Marlin/src/HAL/HAL_STM32_F4_F7/inc/SanityCheck.h similarity index 87% rename from Marlin/src/HAL/HAL_STM32F7/SanityCheck.h rename to Marlin/src/HAL/HAL_STM32_F4_F7/inc/SanityCheck.h index e292de4efe..7b8d29aa7d 100644 --- a/Marlin/src/HAL/HAL_STM32F7/SanityCheck.h +++ b/Marlin/src/HAL/HAL_STM32_F4_F7/inc/SanityCheck.h @@ -22,14 +22,14 @@ #pragma once /** - * Test STM32F7-specific configuration values for errors at compile-time. + * Test STM32F4/7-specific configuration values for errors at compile-time. */ //#if ENABLED(SPINDLE_LASER_PWM) && !(SPINDLE_LASER_PWM_PIN == 4 || SPINDLE_LASER_PWM_PIN == 6 || SPINDLE_LASER_PWM_PIN == 11) // #error "SPINDLE_LASER_PWM_PIN must use SERVO0, SERVO1 or SERVO3 connector" //#endif #if ENABLED(EMERGENCY_PARSER) - #error "EMERGENCY_PARSER is not yet implemented for STM32F7. Disable EMERGENCY_PARSER to continue." + #error "EMERGENCY_PARSER is not yet implemented for STM32F4/7. Disable EMERGENCY_PARSER to continue." #endif #if ENABLED(FAST_PWM_FAN) diff --git a/Marlin/src/HAL/HAL_STM32F7/persistent_store_eeprom.cpp b/Marlin/src/HAL/HAL_STM32_F4_F7/persistent_store_eeprom.cpp similarity index 91% rename from Marlin/src/HAL/HAL_STM32F7/persistent_store_eeprom.cpp rename to Marlin/src/HAL/HAL_STM32_F4_F7/persistent_store_eeprom.cpp index 6d7d103235..4bd86d225d 100644 --- a/Marlin/src/HAL/HAL_STM32F7/persistent_store_eeprom.cpp +++ b/Marlin/src/HAL/HAL_STM32_F4_F7/persistent_store_eeprom.cpp @@ -21,7 +21,7 @@ * */ -#ifdef STM32F7 +#if defined(STM32GENERIC) && (defined(STM32F4) || defined(STM32F7)) #include "../../inc/MarlinConfigPre.h" @@ -52,10 +52,10 @@ bool PersistentStore::write_data(int &pos, const uint8_t *value, size_t size, ui return false; } -bool PersistentStore::read_data(int &pos, uint8_t* value, size_t size, uint16_t *crc) { +bool PersistentStore::read_data(int &pos, uint8_t* value, size_t size, uint16_t *crc, const bool writing/*=true*/) { do { uint8_t c = eeprom_read_byte((uint8_t*)pos); - *value = c; + if (writing) *value = c; crc16(crc, &c, 1); pos++; value++; @@ -66,4 +66,4 @@ bool PersistentStore::read_data(int &pos, uint8_t* value, size_t size, uint16_t size_t PersistentStore::capacity() { return E2END + 1; } #endif // EEPROM_SETTINGS -#endif // STM32F7 +#endif // STM32GENERIC && (STM32F4 || STM32F7) diff --git a/Marlin/src/HAL/HAL_STM32_F4_F7/pinsDebug.h b/Marlin/src/HAL/HAL_STM32_F4_F7/pinsDebug.h new file mode 100644 index 0000000000..342b875561 --- /dev/null +++ b/Marlin/src/HAL/HAL_STM32_F4_F7/pinsDebug.h @@ -0,0 +1,27 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +#ifdef NUM_DIGITAL_PINS // Only in ST's Arduino core (STM32duino, STM32Core) + #include "../HAL_STM32/pinsDebug_STM32duino.h" +#elif defined(BOARD_NR_GPIO_PINS) // Only in STM32GENERIC (Maple) + #include "../HAL_STM32/pinsDebug_STM32GENERIC.h" +#else + #error "M43 Pins Debugging not supported for this board." +#endif diff --git a/Marlin/src/HAL/HAL_STM32F4/spi_pins.h b/Marlin/src/HAL/HAL_STM32_F4_F7/spi_pins.h similarity index 100% rename from Marlin/src/HAL/HAL_STM32F4/spi_pins.h rename to Marlin/src/HAL/HAL_STM32_F4_F7/spi_pins.h diff --git a/Marlin/src/HAL/HAL_STM32F4/watchdog_STM32F4.cpp b/Marlin/src/HAL/HAL_STM32_F4_F7/watchdog_STM32_F4_F7.cpp similarity index 88% rename from Marlin/src/HAL/HAL_STM32F4/watchdog_STM32F4.cpp rename to Marlin/src/HAL/HAL_STM32_F4_F7/watchdog_STM32_F4_F7.cpp index 51b3a8d62d..efb72a8ba7 100644 --- a/Marlin/src/HAL/HAL_STM32F4/watchdog_STM32F4.cpp +++ b/Marlin/src/HAL/HAL_STM32_F4_F7/watchdog_STM32_F4_F7.cpp @@ -20,13 +20,13 @@ * */ -#if defined(STM32GENERIC) && defined(STM32F4) +#if defined(STM32GENERIC) && (defined(STM32F4) || defined(STM32F7)) #include "../../inc/MarlinConfig.h" #if ENABLED(USE_WATCHDOG) - #include "watchdog_STM32F4.h" + #include "watchdog_STM32_F4_F7.h" IWDG_HandleTypeDef hiwdg; @@ -37,6 +37,11 @@ if (HAL_IWDG_Init(&hiwdg) != HAL_OK) { //Error_Handler(); } + else { + #if PIN_EXISTS(LED) && !ENABLED(PINS_DEBUGGING) + TOGGLE(LED_PIN); // heartbeat indicator + #endif + } } void watchdog_reset() { @@ -45,13 +50,7 @@ /* Refresh Error */ //Error_Handler(); } - else { - #if PIN_EXISTS(LED) - TOGGLE(LED_PIN); // heartbeat indicator - #endif - } } #endif // USE_WATCHDOG - -#endif // STM32GENERIC && STM32F4 +#endif // STM32GENERIC && (STM32F4 || STM32F7) diff --git a/Marlin/src/HAL/HAL_STM32F4/watchdog_STM32F4.h b/Marlin/src/HAL/HAL_STM32_F4_F7/watchdog_STM32_F4_F7.h similarity index 100% rename from Marlin/src/HAL/HAL_STM32F4/watchdog_STM32F4.h rename to Marlin/src/HAL/HAL_STM32_F4_F7/watchdog_STM32_F4_F7.h diff --git a/Marlin/src/HAL/HAL_TEENSY31_32/HAL.h b/Marlin/src/HAL/HAL_TEENSY31_32/HAL.h index 0dbfa284e5..18e53a33e3 100644 --- a/Marlin/src/HAL/HAL_TEENSY31_32/HAL.h +++ b/Marlin/src/HAL/HAL_TEENSY31_32/HAL.h @@ -19,19 +19,17 @@ * along with this program. If not, see . * */ +#pragma once /** * Description: HAL for Teensy 3.5 and Teensy 3.6 */ -#pragma once - #define CPU_32_BIT #include "../shared/Marduino.h" - -#include "../math_32bit.h" -#include "../HAL_SPI.h" +#include "../shared/math_32bit.h" +#include "../shared/HAL_SPI.h" #include "fastio_Teensy.h" #include "watchdog_Teensy.h" diff --git a/Marlin/src/HAL/HAL_TEENSY31_32/HAL_timers_Teensy.h b/Marlin/src/HAL/HAL_TEENSY31_32/HAL_timers_Teensy.h index 8c9836d130..52d4965e35 100644 --- a/Marlin/src/HAL/HAL_TEENSY31_32/HAL_timers_Teensy.h +++ b/Marlin/src/HAL/HAL_TEENSY31_32/HAL_timers_Teensy.h @@ -26,17 +26,11 @@ * Teensy3.2 (__MK20DX256__) */ -#pragma once - -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - #include -// -------------------------------------------------------------------------- +// ------------------------ // Defines -// -------------------------------------------------------------------------- +// ------------------------ #define FORCE_INLINE __attribute__((always_inline)) inline @@ -48,8 +42,8 @@ typedef uint32_t hal_timer_t; #define FTM0_TIMER_PRESCALE_BITS 0b011 #define FTM1_TIMER_PRESCALE_BITS 0b010 -#define FTM0_TIMER_RATE (F_BUS / FTM0_TIMER_PRESCALE) // 60MHz / 8 = 7500kHz -#define FTM1_TIMER_RATE (F_BUS / FTM1_TIMER_PRESCALE) // 60MHz / 4 = 15MHz +#define FTM0_TIMER_RATE (F_BUS / (FTM0_TIMER_PRESCALE)) // 60MHz / 8 = 7500kHz +#define FTM1_TIMER_RATE (F_BUS / (FTM1_TIMER_PRESCALE)) // 60MHz / 4 = 15MHz #define HAL_TIMER_RATE (FTM0_TIMER_RATE) diff --git a/Marlin/src/HAL/HAL_TEENSY31_32/endstop_interrupts.h b/Marlin/src/HAL/HAL_TEENSY31_32/endstop_interrupts.h index 1af89e0f33..743f917816 100644 --- a/Marlin/src/HAL/HAL_TEENSY31_32/endstop_interrupts.h +++ b/Marlin/src/HAL/HAL_TEENSY31_32/endstop_interrupts.h @@ -35,8 +35,6 @@ * (Located in Marlin/buildroot/share/pin_interrupt_test/pin_interrupt_test.ino) */ -#pragma once - #include "../../module/endstops.h" // One ISR for all EXT-Interrupts diff --git a/Marlin/src/HAL/HAL_TEENSY31_32/fastio_Teensy.h b/Marlin/src/HAL/HAL_TEENSY31_32/fastio_Teensy.h index 7bcd601b58..d1b5f567d7 100644 --- a/Marlin/src/HAL/HAL_TEENSY31_32/fastio_Teensy.h +++ b/Marlin/src/HAL/HAL_TEENSY31_32/fastio_Teensy.h @@ -27,8 +27,6 @@ * Contributed by Triffid_Hunter and modified by Kliment, thinkyhead, Bob-the-Kuhn, et.al. */ -#pragma once - #ifndef MASK #define MASK(PIN) (1 << PIN) #endif diff --git a/Marlin/src/HAL/HAL_TEENSY31_32/inc/Conditionals_LCD.h b/Marlin/src/HAL/HAL_TEENSY31_32/inc/Conditionals_LCD.h new file mode 100644 index 0000000000..85f26f4016 --- /dev/null +++ b/Marlin/src/HAL/HAL_TEENSY31_32/inc/Conditionals_LCD.h @@ -0,0 +1,22 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once diff --git a/Marlin/src/HAL/HAL_TEENSY31_32/inc/Conditionals_adv.h b/Marlin/src/HAL/HAL_TEENSY31_32/inc/Conditionals_adv.h new file mode 100644 index 0000000000..85f26f4016 --- /dev/null +++ b/Marlin/src/HAL/HAL_TEENSY31_32/inc/Conditionals_adv.h @@ -0,0 +1,22 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once diff --git a/Marlin/src/HAL/HAL_TEENSY31_32/inc/Conditionals_post.h b/Marlin/src/HAL/HAL_TEENSY31_32/inc/Conditionals_post.h new file mode 100644 index 0000000000..85f26f4016 --- /dev/null +++ b/Marlin/src/HAL/HAL_TEENSY31_32/inc/Conditionals_post.h @@ -0,0 +1,22 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once diff --git a/Marlin/src/HAL/HAL_TEENSY31_32/SanityCheck.h b/Marlin/src/HAL/HAL_TEENSY31_32/inc/SanityCheck.h similarity index 100% rename from Marlin/src/HAL/HAL_TEENSY31_32/SanityCheck.h rename to Marlin/src/HAL/HAL_TEENSY31_32/inc/SanityCheck.h diff --git a/Marlin/src/HAL/HAL_TEENSY31_32/persistent_store_impl.cpp b/Marlin/src/HAL/HAL_TEENSY31_32/persistent_store_impl.cpp index d746dc9730..6da102638f 100644 --- a/Marlin/src/HAL/HAL_TEENSY31_32/persistent_store_impl.cpp +++ b/Marlin/src/HAL/HAL_TEENSY31_32/persistent_store_impl.cpp @@ -1,18 +1,33 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ #ifdef __MK20DX256__ #include "../../inc/MarlinConfig.h" #if ENABLED(EEPROM_SETTINGS) -#include "../persistent_store_api.h" +#include "../shared/persistent_store_api.h" -namespace HAL { -namespace PersistentStore { +bool PersistentStore::access_start() { return true; } +bool PersistentStore::access_finish() { return true; } -bool access_start() { return true; } -bool access_finish() { return true; } - -bool write_data(int &pos, const uint8_t *value, uint16_t size, uint16_t *crc) { +bool PersistentStore::write_data(int &pos, const uint8_t *value, size_t size, uint16_t *crc) { while (size--) { uint8_t * const p = (uint8_t * const)pos; uint8_t v = *value; @@ -32,7 +47,7 @@ bool write_data(int &pos, const uint8_t *value, uint16_t size, uint16_t *crc) { return false; } -bool read_data(int &pos, uint8_t* value, uint16_t size, uint16_t *crc, const bool writing/*=true*/) { +bool PersistentStore::read_data(int &pos, uint8_t* value, size_t size, uint16_t *crc, const bool writing/*=true*/) { do { uint8_t c = eeprom_read_byte((uint8_t*)pos); if (writing) *value = c; @@ -43,8 +58,5 @@ bool read_data(int &pos, uint8_t* value, uint16_t size, uint16_t *crc, const boo return false; } -} // PersistentStore -} // HAL - #endif // EEPROM_SETTINGS #endif // __MK20DX256__ diff --git a/Marlin/src/HAL/HAL_TEENSY35_36/HAL.h b/Marlin/src/HAL/HAL_TEENSY35_36/HAL.h index f3a26eb5d8..4a8de159b0 100644 --- a/Marlin/src/HAL/HAL_TEENSY35_36/HAL.h +++ b/Marlin/src/HAL/HAL_TEENSY35_36/HAL.h @@ -27,10 +27,6 @@ #define CPU_32_BIT -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - #include "../shared/Marduino.h" #include "../shared/math_32bit.h" #include "../shared/HAL_SPI.h" @@ -47,9 +43,9 @@ #define ST7920_DELAY_2 DELAY_NS(750) #define ST7920_DELAY_3 DELAY_NS(750) -// -------------------------------------------------------------------------- +// ------------------------ // Defines -// -------------------------------------------------------------------------- +// ------------------------ #define IS_32BIT_TEENSY (defined(__MK64FX512__) || defined(__MK66FX1M0__)) #define IS_TEENSY35 defined(__MK64FX512__) diff --git a/Marlin/src/HAL/HAL_TEENSY35_36/HAL_timers_Teensy.h b/Marlin/src/HAL/HAL_TEENSY35_36/HAL_timers_Teensy.h index 8263691947..741f27c0ba 100644 --- a/Marlin/src/HAL/HAL_TEENSY35_36/HAL_timers_Teensy.h +++ b/Marlin/src/HAL/HAL_TEENSY35_36/HAL_timers_Teensy.h @@ -25,15 +25,11 @@ * Teensy3.6 (__MK66FX1M0__) */ -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - #include -// -------------------------------------------------------------------------- +// ------------------------ // Defines -// -------------------------------------------------------------------------- +// ------------------------ #define FORCE_INLINE __attribute__((always_inline)) inline diff --git a/Marlin/src/HAL/HAL_TEENSY35_36/inc/Conditionals_LCD.h b/Marlin/src/HAL/HAL_TEENSY35_36/inc/Conditionals_LCD.h new file mode 100644 index 0000000000..85f26f4016 --- /dev/null +++ b/Marlin/src/HAL/HAL_TEENSY35_36/inc/Conditionals_LCD.h @@ -0,0 +1,22 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once diff --git a/Marlin/src/HAL/HAL_TEENSY35_36/inc/Conditionals_adv.h b/Marlin/src/HAL/HAL_TEENSY35_36/inc/Conditionals_adv.h new file mode 100644 index 0000000000..85f26f4016 --- /dev/null +++ b/Marlin/src/HAL/HAL_TEENSY35_36/inc/Conditionals_adv.h @@ -0,0 +1,22 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once diff --git a/Marlin/src/HAL/HAL_TEENSY35_36/inc/Conditionals_post.h b/Marlin/src/HAL/HAL_TEENSY35_36/inc/Conditionals_post.h new file mode 100644 index 0000000000..85f26f4016 --- /dev/null +++ b/Marlin/src/HAL/HAL_TEENSY35_36/inc/Conditionals_post.h @@ -0,0 +1,22 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once diff --git a/Marlin/src/HAL/HAL_TEENSY35_36/SanityCheck.h b/Marlin/src/HAL/HAL_TEENSY35_36/inc/SanityCheck.h similarity index 100% rename from Marlin/src/HAL/HAL_TEENSY35_36/SanityCheck.h rename to Marlin/src/HAL/HAL_TEENSY35_36/inc/SanityCheck.h diff --git a/Marlin/src/HAL/HAL_TEENSY35_36/persistent_store_impl.cpp b/Marlin/src/HAL/HAL_TEENSY35_36/persistent_store_impl.cpp deleted file mode 100644 index 29b4653b3e..0000000000 --- a/Marlin/src/HAL/HAL_TEENSY35_36/persistent_store_impl.cpp +++ /dev/null @@ -1,50 +0,0 @@ -#if defined(__MK64FX512__) || defined(__MK66FX1M0__) - -#include "../../inc/MarlinConfig.h" - -#if ENABLED(EEPROM_SETTINGS) - -#include "../shared/persistent_store_api.h" - -namespace HAL { -namespace PersistentStore { - -bool access_start() { return true; } -bool access_finish() { return true; } - -bool write_data(int &pos, const uint8_t *value, uint16_t size, uint16_t *crc) { - while (size--) { - uint8_t * const p = (uint8_t * const)pos; - uint8_t v = *value; - // EEPROM has only ~100,000 write cycles, - // so only write bytes that have changed! - if (v != eeprom_read_byte(p)) { - eeprom_write_byte(p, v); - if (eeprom_read_byte(p) != v) { - SERIAL_ECHO_MSG(MSG_ERR_EEPROM_WRITE); - return true; - } - } - crc16(crc, &v, 1); - pos++; - value++; - }; - return false; -} - -bool read_data(int &pos, uint8_t* value, uint16_t size, uint16_t *crc, const bool writing/*=true*/) { - do { - uint8_t c = eeprom_read_byte((uint8_t*)pos); - if (writing) *value = c; - crc16(crc, &c, 1); - pos++; - value++; - } while (--size); - return false; -} - -} // PersistentStore -} // HAL - -#endif // EEPROM_SETTINGS -#endif // __MK64FX512__ || __MK66FX1M0__ diff --git a/Marlin/src/HAL/HAL_TEENSY35_36/pinsDebug.h b/Marlin/src/HAL/HAL_TEENSY35_36/pinsDebug.h index e6dcb2996c..db750cf6ec 100644 --- a/Marlin/src/HAL/HAL_TEENSY35_36/pinsDebug.h +++ b/Marlin/src/HAL/HAL_TEENSY35_36/pinsDebug.h @@ -16,8 +16,7 @@ * along with this program. If not, see . * */ - -#ifndef HAL_PINSDEBUG_TEENSY_H +#pragma once #define NUMBER_PINS_TOTAL NUM_DIGITAL_PINS #define MULTI_NAME_PAD 16 // space needed to be pretty if not first name assigned to a pin @@ -103,5 +102,3 @@ bool HAL_pwm_status(int8_t pin) { } static void HAL_pwm_details(uint8_t pin) { /* TODO */ } - -#endif diff --git a/Marlin/src/HAL/platforms.h b/Marlin/src/HAL/platforms.h index 48405f49f7..e3e7f52cfa 100644 --- a/Marlin/src/HAL/platforms.h +++ b/Marlin/src/HAL/platforms.h @@ -33,16 +33,16 @@ #define HAL_PLATFORM HAL_LPC1768 #elif defined(__STM32F1__) || defined(TARGET_STM32F1) #define HAL_PLATFORM HAL_STM32F1 -#elif defined(STM32GENERIC) && defined(STM32F4) - #define HAL_PLATFORM HAL_STM32F4 -#elif defined(STM32GENERIC) && defined(STM32F7) - #define HAL_PLATFORM HAL_STM32F7 +#elif defined(STM32GENERIC) && (defined(STM32F4) || defined(STM32F7)) + #define HAL_PLATFORM HAL_STM32_F4_F7 #elif defined(ARDUINO_ARCH_STM32) #define HAL_PLATFORM HAL_STM32 #elif defined(ARDUINO_ARCH_ESP32) #define HAL_PLATFORM HAL_ESP32 #elif defined(__PLAT_LINUX__) #define HAL_PLATFORM HAL_LINUX +#elif defined(__SAMD51__) + #define HAL_PLATFORM HAL_SAMD51 #else #error "Unsupported Platform!" #endif diff --git a/Marlin/src/HAL/shared/Marduino.h b/Marlin/src/HAL/shared/Marduino.h index d9440325f2..891646daab 100644 --- a/Marlin/src/HAL/shared/Marduino.h +++ b/Marlin/src/HAL/shared/Marduino.h @@ -29,6 +29,8 @@ #undef M_PI // Redefined by all #undef _BV // Redefined by some #undef sq // Redefined by teensy3/wiring.h +#undef SBI // Redefined by arduino/const_functions.h +#undef CBI // Redefined by arduino/const_functions.h #include // NOTE: If included earlier then this line is a NOOP @@ -54,6 +56,10 @@ inline const char* strchr_P(const char *s, int c) { return strchr(s,c); } //#define strchr_P(s,c) strchr(s,c) #endif + + #ifndef vsnprintf_P + #define vsnprintf_P vsnprintf + #endif #endif // Restart causes diff --git a/Marlin/src/HAL/shared/backtrace/unwmemaccess.cpp b/Marlin/src/HAL/shared/backtrace/unwmemaccess.cpp index 20f1a7bc0f..8cf31cadf5 100644 --- a/Marlin/src/HAL/shared/backtrace/unwmemaccess.cpp +++ b/Marlin/src/HAL/shared/backtrace/unwmemaccess.cpp @@ -129,6 +129,17 @@ #define END_FLASH_ADDR 0x00140000 #endif +#ifdef __SAMD51P20A__ +// For SAMD51x20, valid address ranges are +// SRAM (0x20000000 - 0x20040000) (256kb) +// FLASH (0x00000000 - 0x00100000) (1024kb) +// +#define START_SRAM_ADDR 0x20000000 +#define END_SRAM_ADDR 0x20040000 +#define START_FLASH_ADDR 0x00000000 +#define END_FLASH_ADDR 0x00100000 +#endif + static bool validate_addr(uint32_t addr) { // Address must be in SRAM range diff --git a/Marlin/src/HAL/shared/I2cEeprom.cpp b/Marlin/src/HAL/shared/eeprom_i2c.cpp similarity index 67% rename from Marlin/src/HAL/shared/I2cEeprom.cpp rename to Marlin/src/HAL/shared/eeprom_i2c.cpp index cc98ac183d..f5e470541d 100644 --- a/Marlin/src/HAL/shared/I2cEeprom.cpp +++ b/Marlin/src/HAL/shared/eeprom_i2c.cpp @@ -29,51 +29,19 @@ #if ENABLED(I2C_EEPROM) -// -------------------------------------------------------------------------- -// Includes -// -------------------------------------------------------------------------- - -#include HAL_PATH(.., HAL.h) +#include "../HAL.h" #include -// -------------------------------------------------------------------------- -// Externals -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Local defines -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Types -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Variables -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Public Variables -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- +// ------------------------ // Private Variables -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Function prototypes -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Private functions -// -------------------------------------------------------------------------- - -// -------------------------------------------------------------------------- -// Public functions -// -------------------------------------------------------------------------- +// ------------------------ static uint8_t eeprom_device_address = 0x50; +// ------------------------ +// Public functions +// ------------------------ + static void eeprom_init(void) { static bool eeprom_initialized = false; if (!eeprom_initialized) { @@ -127,7 +95,6 @@ void eeprom_update_block(const void *pos, void* eeprom_address, size_t n) { } } - uint8_t eeprom_read_byte(uint8_t *pos) { unsigned eeprom_address = (unsigned)pos; @@ -141,7 +108,7 @@ uint8_t eeprom_read_byte(uint8_t *pos) { return Wire.available() ? Wire.read() : 0xFF; } -// maybe let's not read more than 30 or 32 bytes at a time! +// Don't read more than 30..32 bytes at a time! void eeprom_read_block(void* pos, const void* eeprom_address, size_t n) { eeprom_init(); diff --git a/Marlin/src/HAL/shared/SpiEeprom.cpp b/Marlin/src/HAL/shared/eeprom_spi.cpp similarity index 99% rename from Marlin/src/HAL/shared/SpiEeprom.cpp rename to Marlin/src/HAL/shared/eeprom_spi.cpp index cbdb4d2985..35e7d9b0a9 100644 --- a/Marlin/src/HAL/shared/SpiEeprom.cpp +++ b/Marlin/src/HAL/shared/eeprom_spi.cpp @@ -29,7 +29,7 @@ #if ENABLED(SPI_EEPROM) -#include HAL_PATH(.., HAL.h) +#include "../HAL.h" #define CMD_WREN 6 // WREN #define CMD_READ 2 // WRITE diff --git a/Marlin/src/HAL/shared/servo.cpp b/Marlin/src/HAL/shared/servo.cpp index af33853665..22cf6bc88f 100644 --- a/Marlin/src/HAL/shared/servo.cpp +++ b/Marlin/src/HAL/shared/servo.cpp @@ -116,9 +116,8 @@ void Servo::detach() { } void Servo::write(int value) { - if (value < MIN_PULSE_WIDTH) { // treat values less than 544 as angles in degrees (valid values in microseconds are handled as microseconds) + if (value < MIN_PULSE_WIDTH) // treat values less than 544 as angles in degrees (valid values in microseconds are handled as microseconds) value = map(constrain(value, 0, 180), 0, 180, SERVO_MIN(), SERVO_MAX()); - } this->writeMicroseconds(value); } @@ -140,7 +139,7 @@ void Servo::writeMicroseconds(int value) { int Servo::read() { return map(this->readMicroseconds() + 1, SERVO_MIN(), SERVO_MAX(), 0, 180); } int Servo::readMicroseconds() { - return (this->servoIndex == INVALID_SERVO) ? 0 : ticksToUs(servo_info[this->servoIndex].ticks) + TRIM_DURATION; + return (this->servoIndex == INVALID_SERVO) ? 0 : ticksToUs(servo_info[this->servoIndex].ticks) + (TRIM_DURATION); } bool Servo::attached() { return servo_info[this->servoIndex].Pin.isActive; } diff --git a/Marlin/src/HAL/shared/servo.h b/Marlin/src/HAL/shared/servo.h index b6b2d13e98..d1a83bf169 100644 --- a/Marlin/src/HAL/shared/servo.h +++ b/Marlin/src/HAL/shared/servo.h @@ -67,8 +67,6 @@ * With DEACTIVATE_SERVOS_AFTER_MOVE wait SERVO_DELAY and detach. */ -#pragma once - #if IS_TEENSY32 #include "../HAL_TEENSY31_32/HAL_Servo_Teensy.h" #elif IS_TEENSY35 || IS_TEENSY36 @@ -86,10 +84,10 @@ #else #include - #if defined(__AVR__) || defined(ARDUINO_ARCH_SAM) + #if defined(__AVR__) || defined(ARDUINO_ARCH_SAM) || defined (__SAMD51__) // we're good to go #else - #error "This library only supports boards with an AVR or SAM3X processor." + #error "This library only supports boards with an AVR, SAM3X or SAMD51 processor." #endif #define Servo_VERSION 2 // software version of this library diff --git a/Marlin/src/HAL/shared/servo_private.h b/Marlin/src/HAL/shared/servo_private.h index 12d4740525..1d4cdc7e3e 100644 --- a/Marlin/src/HAL/shared/servo_private.h +++ b/Marlin/src/HAL/shared/servo_private.h @@ -47,8 +47,10 @@ #include "../HAL_AVR/ServoTimers.h" #elif defined(ARDUINO_ARCH_SAM) #include "../HAL_DUE/ServoTimers.h" +#elif defined(__SAMD51__) + #include "../HAL_SAMD51/ServoTimers.h" #else - #error "This library only supports boards with an AVR or SAM3X processor." + #error "This library only supports boards with an AVR, SAM3X or SAMD51 processor." #endif // Macros @@ -64,10 +66,8 @@ #define INVALID_SERVO 255 // flag indicating an invalid servo index // Convert microseconds to ticks and back (PRESCALER depends on architecture) -#define usToTicks(_us) (clockCyclesPerMicrosecond() * (_us) / (PRESCALER)) -#define ticksToUs(_ticks) (unsigned(_ticks) * (PRESCALER) / clockCyclesPerMicrosecond()) - -//#define NBR_TIMERS ((MAX_SERVOS) / (SERVOS_PER_TIMER)) +#define usToTicks(_us) (clockCyclesPerMicrosecond() * (_us) / (SERVO_TIMER_PRESCALER)) +#define ticksToUs(_ticks) (unsigned(_ticks) * (SERVO_TIMER_PRESCALER) / clockCyclesPerMicrosecond()) // convenience macros #define SERVO_INDEX_TO_TIMER(_servo_nbr) ((timer16_Sequence_t)(_servo_nbr / (SERVOS_PER_TIMER))) // returns the timer controlling this servo @@ -78,7 +78,7 @@ // Types typedef struct { - uint8_t nbr : 6 ; // a pin number from 0 to 63 + uint8_t nbr : 7 ; // a pin number from 0 to 127 uint8_t isActive : 1 ; // true if this channel is enabled, pin not pulsed if false } ServoPin_t; diff --git a/Marlin/src/Marlin.cpp b/Marlin/src/Marlin.cpp index e73066fabf..d1f5fe53b6 100644 --- a/Marlin/src/Marlin.cpp +++ b/Marlin/src/Marlin.cpp @@ -57,6 +57,10 @@ #include "gcode/parser.h" #include "gcode/queue.h" +#if ENABLED(TOUCH_BUTTONS) + #include "feature/touch/xpt2046.h" +#endif + #if ENABLED(HOST_ACTION_COMMANDS) #include "feature/host_actions.h" #endif @@ -683,9 +687,12 @@ void idle( #if ENABLED(I2C_POSITION_ENCODERS) static millis_t i2cpem_next_update_ms; - if (planner.has_blocks_queued() && ELAPSED(millis(), i2cpem_next_update_ms)) { - I2CPEM.update(); - i2cpem_next_update_ms = millis() + I2CPE_MIN_UPD_TIME_MS; + if (planner.has_blocks_queued()) { + const millis_t ms = millis(); + if (ELAPSED(ms, i2cpem_next_update_ms)) { + I2CPEM.update(); + i2cpem_next_update_ms = ms + I2CPE_MIN_UPD_TIME_MS; + } } #endif @@ -860,7 +867,7 @@ void setup() { setup_killpin(); - #if HAS_DRIVER(TMC2208) || HAS_DRIVER(TMC2209) + #if HAS_TMC220x tmc_serial_begin(); #endif @@ -941,7 +948,11 @@ void setup() { // Load data from EEPROM if available (or use defaults) // This also updates variables in the planner, elsewhere - (void)settings.load(); + settings.first_load(); + + #if ENABLED(TOUCH_BUTTONS) + touch.init(); + #endif #if HAS_M206_COMMAND // Initialize current position based on home_offset diff --git a/Marlin/src/core/boards.h b/Marlin/src/core/boards.h index c9c5d412fa..7d02566247 100644 --- a/Marlin/src/core/boards.h +++ b/Marlin/src/core/boards.h @@ -88,92 +88,100 @@ #define BOARD_RAMPS_ENDER_4 1134 // Creality: Ender-4, CR-8 #define BOARD_RAMPS_CREALITY 1135 // Creality: CR10S, CR20, CR-X #define BOARD_RAMPS_DAGOMA 1136 // Dagoma F5 -#define BOARD_FYSETC_F6_13 1137 // Fysetc F6 +#define BOARD_FYSETC_F6_13 1137 // FYSETC F6 #define BOARD_DUPLICATOR_I3_PLUS 1138 // Wanhao Duplicator i3 Plus #define BOARD_VORON 1139 // VORON Design #define BOARD_TRONXY_V3_1_0 1140 // Tronxy TRONXY-V3-1.0 #define BOARD_Z_BOLT_X_SERIES 1141 // Z-Bolt X Series +#define BOARD_TT_OSCAR 1142 // TT OSCAR +#define BOARD_OVERLORD 1143 // Overlord/Overlord Pro + +// +// RAMBo and derivatives +// + +#define BOARD_RAMBO 1200 // Rambo +#define BOARD_MINIRAMBO 1201 // Mini-Rambo +#define BOARD_MINIRAMBO_10A 1202 // Mini-Rambo 1.0a +#define BOARD_EINSY_RAMBO 1203 // Einsy Rambo +#define BOARD_EINSY_RETRO 1204 // Einsy Retro +#define BOARD_SCOOVO_X9H 1205 // abee Scoovo X9H // // Other ATmega1280, ATmega2560 // -#define BOARD_CNCONTROLS_11 1200 // Cartesio CN Controls V11 -#define BOARD_CNCONTROLS_12 1201 // Cartesio CN Controls V12 -#define BOARD_CHEAPTRONIC 1202 // Cheaptronic v1.0 -#define BOARD_CHEAPTRONIC_V2 1203 // Cheaptronic v2.0 -#define BOARD_MIGHTYBOARD_REVE 1204 // Makerbot Mightyboard Revision E -#define BOARD_MEGATRONICS 1205 // Megatronics -#define BOARD_MEGATRONICS_2 1206 // Megatronics v2.0 -#define BOARD_MEGATRONICS_3 1207 // Megatronics v3.0 -#define BOARD_MEGATRONICS_31 1208 // Megatronics v3.1 -#define BOARD_MEGATRONICS_32 1209 // Megatronics v3.2 -#define BOARD_RAMBO 1210 // Rambo -#define BOARD_MINIRAMBO 1211 // Mini-Rambo -#define BOARD_MINIRAMBO_10A 1212 // Mini-Rambo 1.0a -#define BOARD_EINSY_RAMBO 1213 // Einsy Rambo -#define BOARD_EINSY_RETRO 1214 // Einsy Retro -#define BOARD_ELEFU_3 1215 // Elefu Ra Board (v3) -#define BOARD_LEAPFROG 1216 // Leapfrog -#define BOARD_MEGACONTROLLER 1217 // Mega controller -#define BOARD_SCOOVO_X9H 1218 // abee Scoovo X9H -#define BOARD_GT2560_REV_A 1219 // Geeetech GT2560 Rev. A -#define BOARD_GT2560_REV_A_PLUS 1220 // Geeetech GT2560 Rev. A+ (with auto level probe) -#define BOARD_GT2560_V3 1221 // Geeetech GT2560 Rev B for A10(M/D) -#define BOARD_GT2560_V3_MC2 1222 // Geeetech GT2560 Rev B for Mecreator2 -#define BOARD_GT2560_V3_A20 1223 // Geeetech GT2560 Rev B for A20(M/D) -#define BOARD_EINSTART_S 1224 // Einstart retrofit +#define BOARD_CNCONTROLS_11 1300 // Cartesio CN Controls V11 +#define BOARD_CNCONTROLS_12 1301 // Cartesio CN Controls V12 +#define BOARD_CHEAPTRONIC 1302 // Cheaptronic v1.0 +#define BOARD_CHEAPTRONIC_V2 1303 // Cheaptronic v2.0 +#define BOARD_MIGHTYBOARD_REVE 1304 // Makerbot Mightyboard Revision E +#define BOARD_MEGATRONICS 1305 // Megatronics +#define BOARD_MEGATRONICS_2 1306 // Megatronics v2.0 +#define BOARD_MEGATRONICS_3 1307 // Megatronics v3.0 +#define BOARD_MEGATRONICS_31 1308 // Megatronics v3.1 +#define BOARD_MEGATRONICS_32 1309 // Megatronics v3.2 +#define BOARD_ELEFU_3 1310 // Elefu Ra Board (v3) +#define BOARD_LEAPFROG 1311 // Leapfrog +#define BOARD_MEGACONTROLLER 1312 // Mega controller +#define BOARD_GT2560_REV_A 1313 // Geeetech GT2560 Rev. A +#define BOARD_GT2560_REV_A_PLUS 1314 // Geeetech GT2560 Rev. A+ (with auto level probe) +#define BOARD_GT2560_V3 1315 // Geeetech GT2560 Rev B for A10(M/D) +#define BOARD_GT2560_V3_MC2 1316 // Geeetech GT2560 Rev B for Mecreator2 +#define BOARD_GT2560_V3_A20 1317 // Geeetech GT2560 Rev B for A20(M/D) +#define BOARD_EINSTART_S 1318 // Einstart retrofit +#define BOARD_WANHAO_ONEPLUS 1319 // Wanhao 0ne+ i3 Mini // // ATmega1281, ATmega2561 // -#define BOARD_MINITRONICS 1300 // Minitronics v1.0/1.1 -#define BOARD_SILVER_GATE 1301 // Silvergate v1.0 +#define BOARD_MINITRONICS 1400 // Minitronics v1.0/1.1 +#define BOARD_SILVER_GATE 1401 // Silvergate v1.0 // // Sanguinololu and Derivatives - ATmega644P, ATmega1284P // -#define BOARD_SANGUINOLOLU_11 1400 // Sanguinololu < 1.2 -#define BOARD_SANGUINOLOLU_12 1401 // Sanguinololu 1.2 and above -#define BOARD_MELZI 1402 // Melzi -#define BOARD_MELZI_MAKR3D 1403 // Melzi with ATmega1284 (MaKr3d version) -#define BOARD_MELZI_CREALITY 1404 // Melzi Creality3D board (for CR-10 etc) -#define BOARD_MELZI_MALYAN 1405 // Melzi Malyan M150 board -#define BOARD_MELZI_TRONXY 1406 // Tronxy X5S -#define BOARD_STB_11 1407 // STB V1.1 -#define BOARD_AZTEEG_X1 1408 // Azteeg X1 -#define BOARD_ANET_10 1409 // Anet 1.0 (Melzi clone) +#define BOARD_SANGUINOLOLU_11 1500 // Sanguinololu < 1.2 +#define BOARD_SANGUINOLOLU_12 1501 // Sanguinololu 1.2 and above +#define BOARD_MELZI 1502 // Melzi +#define BOARD_MELZI_MAKR3D 1503 // Melzi with ATmega1284 (MaKr3d version) +#define BOARD_MELZI_CREALITY 1504 // Melzi Creality3D board (for CR-10 etc) +#define BOARD_MELZI_MALYAN 1505 // Melzi Malyan M150 board +#define BOARD_MELZI_TRONXY 1506 // Tronxy X5S +#define BOARD_STB_11 1507 // STB V1.1 +#define BOARD_AZTEEG_X1 1508 // Azteeg X1 +#define BOARD_ANET_10 1509 // Anet 1.0 (Melzi clone) // // Other ATmega644P, ATmega644, ATmega1284P // -#define BOARD_GEN3_MONOLITHIC 1500 // Gen3 Monolithic Electronics -#define BOARD_GEN3_PLUS 1501 // Gen3+ -#define BOARD_GEN6 1502 // Gen6 -#define BOARD_GEN6_DELUXE 1503 // Gen6 deluxe -#define BOARD_GEN7_CUSTOM 1504 // Gen7 custom (Alfons3 Version) "https://github.com/Alfons3/Generation_7_Electronics" -#define BOARD_GEN7_12 1505 // Gen7 v1.1, v1.2 -#define BOARD_GEN7_13 1506 // Gen7 v1.3 -#define BOARD_GEN7_14 1507 // Gen7 v1.4 -#define BOARD_OMCA_A 1508 // Alpha OMCA board -#define BOARD_OMCA 1509 // Final OMCA board -#define BOARD_SETHI 1510 // Sethi 3D_1 +#define BOARD_GEN3_MONOLITHIC 1600 // Gen3 Monolithic Electronics +#define BOARD_GEN3_PLUS 1601 // Gen3+ +#define BOARD_GEN6 1602 // Gen6 +#define BOARD_GEN6_DELUXE 1603 // Gen6 deluxe +#define BOARD_GEN7_CUSTOM 1604 // Gen7 custom (Alfons3 Version) "https://github.com/Alfons3/Generation_7_Electronics" +#define BOARD_GEN7_12 1605 // Gen7 v1.1, v1.2 +#define BOARD_GEN7_13 1606 // Gen7 v1.3 +#define BOARD_GEN7_14 1607 // Gen7 v1.4 +#define BOARD_OMCA_A 1608 // Alpha OMCA board +#define BOARD_OMCA 1609 // Final OMCA board +#define BOARD_SETHI 1610 // Sethi 3D_1 // // Teensyduino - AT90USB1286, AT90USB1286P // -#define BOARD_TEENSYLU 1600 // Teensylu -#define BOARD_PRINTRBOARD 1601 // Printrboard (AT90USB1286) -#define BOARD_PRINTRBOARD_REVF 1602 // Printrboard Revision F (AT90USB1286) -#define BOARD_BRAINWAVE 1603 // Brainwave (AT90USB646) -#define BOARD_BRAINWAVE_PRO 1604 // Brainwave Pro (AT90USB1286) -#define BOARD_SAV_MKI 1605 // SAV Mk-I (AT90USB1286) -#define BOARD_TEENSY2 1606 // Teensy++2.0 (AT90USB1286) -#define BOARD_5DPRINT 1607 // 5DPrint D8 Driver Board +#define BOARD_TEENSYLU 1700 // Teensylu +#define BOARD_PRINTRBOARD 1701 // Printrboard (AT90USB1286) +#define BOARD_PRINTRBOARD_REVF 1702 // Printrboard Revision F (AT90USB1286) +#define BOARD_BRAINWAVE 1703 // Brainwave (AT90USB646) +#define BOARD_BRAINWAVE_PRO 1704 // Brainwave Pro (AT90USB1286) +#define BOARD_SAV_MKI 1705 // SAV Mk-I (AT90USB1286) +#define BOARD_TEENSY2 1706 // Teensy++2.0 (AT90USB1286) +#define BOARD_5DPRINT 1707 // 5DPrint D8 Driver Board // // LPC1768 ARM Cortex M3 @@ -193,13 +201,14 @@ #define BOARD_COHESION3D_MINI 2011 // Cohesion3D Mini #define BOARD_SMOOTHIEBOARD 2012 // Smoothieboard #define BOARD_AZTEEG_X5_MINI_WIFI 2013 // Azteeg X5 Mini Wifi (Power outputs: Hotend0, Bed, Fan) -#define BOARD_BIQU_SKR_V1_1 2014 // BIQU SKR_V1.1 (Power outputs: Hotend0,Hotend1, Fan, Bed) +#define BOARD_BIGTREE_SKR_V1_1 2014 // BIGTREE SKR_V1.1 (Power outputs: Hotend0,Hotend1, Fan, Bed) #define BOARD_BIQU_B300_V1_0 2015 // BIQU B300_V1.0 (Power outputs: Hotend0, Fan, Bed, SPI Driver) #define BOARD_BIGTREE_SKR_V1_3 2016 // BIGTREE SKR_V1.3 (Power outputs: Hotend0, Hotend1, Fan, Bed) #define BOARD_AZTEEG_X5_MINI 2017 // Azteeg X5 Mini (Power outputs: Hotend0, Bed, Fan) #define BOARD_MKS_SGEN 2018 // MKS-SGen (Power outputs: Hotend0, Hotend1, Bed, Fan) #define BOARD_MKS_SGEN_L 2019 // MKS-SGen-L (Power outputs: Hotend0, Hotend1, Bed, Fan) #define BOARD_TH3D_EZBOARD 2020 // TH3D EZBoard v1.0 +#define BOARD_GMARSH_X6_REV1 2021 // GMARSH X6 board, revision 1 prototype // // SAM3X8E ARM Cortex M3 @@ -248,28 +257,39 @@ #define BOARD_STM3R_MINI 4002 // STM32 Libmaple-based STM32F1 controller #define BOARD_GTM32_PRO_VB 4003 // STM32F103VET6 controller #define BOARD_MORPHEUS 4004 // STM32F103C8 / STM32F103CB Libmaple-based STM32F1 controller -#define BOARD_MKS_ROBIN 4005 // MKS Robin (STM32F103ZET6) -#define BOARD_MKS_ROBIN_MINI 4006 // MKS Robin Mini (STM32F103VET6) -#define BOARD_MKS_ROBIN_NANO 4007 // MKS Robin Nano (STM32F103VET6) -#define BOARD_BIGTREE_SKR_MINI_V1_1 4008 // BigTreeTech SKR Mini v1.1 (STM32F103RC) -#define BOARD_BIGTREE_SKR_MINI_E3 4009 // BigTreeTech SKR Mini E3 (STM32F103RC) -#define BOARD_JGAURORA_A5S_A1 4010 // JGAurora A5S A1 (STM32F103ZET6) -#define BOARD_FYSETC_AIO_II 4011 // FYSETC AIO_II -#define BOARD_FYSETC_CHEETAH 4012 // FYSETC CHEETAH +#define BOARD_CHITU3D 4005 // Chitu3D (STM32F103RET6) +#define BOARD_MKS_ROBIN 4006 // MKS Robin (STM32F103ZET6) +#define BOARD_MKS_ROBIN_MINI 4007 // MKS Robin Mini (STM32F103VET6) +#define BOARD_MKS_ROBIN_NANO 4008 // MKS Robin Nano (STM32F103VET6) +#define BOARD_MKS_ROBIN_LITE 4009 // MKS Robin Lite/Lite2 (STM32F103RCT6) +#define BOARD_BIGTREE_SKR_MINI_V1_1 4010 // BigTreeTech SKR Mini v1.1 (STM32F103RC) +#define BOARD_BIGTREE_SKR_MINI_E3 4011 // BigTreeTech SKR Mini E3 (STM32F103RC) +#define BOARD_BIGTREE_SKR_E3_DIP 4012 // BigTreeTech SKR E3 DIP V1.0 (STM32F103RC) +#define BOARD_JGAURORA_A5S_A1 4013 // JGAurora A5S A1 (STM32F103ZET6) +#define BOARD_FYSETC_AIO_II 4014 // FYSETC AIO_II +#define BOARD_FYSETC_CHEETAH 4015 // FYSETC Cheetah +#define BOARD_FYSETC_CHEETAH_V12 4016 // FYSETC Cheetah V1.2 +#define BOARD_LONGER3D_LK 4017 // Alfawise U20/U20+/U30 (Longer3D LK1/2) / STM32F103VET6 + +// +// ARM Cortex-M4F +// + +#define BOARD_TEENSY31_32 4100 // Teensy3.1 and Teensy3.2 +#define BOARD_TEENSY35_36 4101 // Teensy3.5 and Teensy3.6 // // STM32 ARM Cortex-M4F // -#define BOARD_TEENSY31_32 4100 // Teensy3.1 and Teensy3.2 -#define BOARD_TEENSY35_36 4101 // Teensy3.5 and Teensy3.6 -#define BOARD_BEAST 4102 // STM32F4xxVxT6 Libmaple-based STM32F4 controller -#define BOARD_STM32F4 4103 // STM32 STM32GENERIC-based STM32F4 controller -#define BOARD_ARMED 4104 // Arm'ed STM32F4-based controller -#define BOARD_RUMBA32 4105 // RUMBA32 STM32F4-based controller -#define BOARD_BLACK_STM32F407VE 4106 // BLACK_STM32F407VE -#define BOARD_BLACK_STM32F407ZE 4107 // BLACK_STM32F407ZE -#define BOARD_STEVAL 4108 // STEVAL-3DP001V1 3D PRINTER BOARD +#define BOARD_BEAST 4200 // STM32F4xxVxT6 Libmaple-based STM32F4 controller +#define BOARD_STM32F4 4201 // STM32 STM32GENERIC-based STM32F4 controller +#define BOARD_ARMED 4202 // Arm'ed STM32F4-based controller +#define BOARD_RUMBA32 4203 // RUMBA32 STM32F4-based controller +#define BOARD_BLACK_STM32F407VE 4204 // BLACK_STM32F407VE +#define BOARD_BLACK_STM32F407ZE 4205 // BLACK_STM32F407ZE +#define BOARD_STEVAL 4206 // STEVAL-3DP001V1 3D PRINTER BOARD +#define BOARD_BIGTREE_SKR_PRO_V1_1 4207 // BigTreeTech SKR Pro v1.1 (STM32F407ZG) // // ARM Cortex M7 @@ -283,6 +303,11 @@ // #define BOARD_ESP32 6000 +// +// SAMD51 ARM Cortex M4 +// +#define BOARD_AGCM4_RURAMPS4D_13 6100 + // // Simulations // diff --git a/Marlin/src/core/drivers.h b/Marlin/src/core/drivers.h index a6e480c141..617090a6f2 100644 --- a/Marlin/src/core/drivers.h +++ b/Marlin/src/core/drivers.h @@ -84,6 +84,8 @@ || HAS_DRIVER(TMC5130) \ || HAS_DRIVER(TMC5160) ) +#define HAS_TMC220x (HAS_DRIVER(TMC2208) || HAS_DRIVER(TMC2209)) + #define AXIS_IS_TMC(A) ( AXIS_DRIVER_TYPE(A,TMC2130) \ || AXIS_DRIVER_TYPE(A,TMC2160) \ || AXIS_DRIVER_TYPE(A,TMC2208) \ @@ -118,7 +120,7 @@ || AXIS_DRIVER_TYPE(A,TMC5160) ) // -// Stretching 'drivers.h' to include LPC SD options +// Stretching 'drivers.h' to include LPC/SAMD51 SD options // #define _SDCARD_LCD 1 #define _SDCARD_ONBOARD 2 diff --git a/Marlin/src/core/language.h b/Marlin/src/core/language.h index c291b0549a..07cdddedee 100644 --- a/Marlin/src/core/language.h +++ b/Marlin/src/core/language.h @@ -37,7 +37,7 @@ // NOTE: IF YOU CHANGE LANGUAGE FILES OR MERGE A FILE WITH CHANGES // -// ==> ALWAYS TRY TO COMPILE MARLIN WITH/WITHOUT "ULTIPANEL" / "ULTRALCD" / "SDSUPPORT" #define IN "Configuration.h" +// ==> ALWAYS TRY TO COMPILE MARLIN WITH/WITHOUT "ULTIPANEL" / "ULTRA_LCD" / "SDSUPPORT" #define IN "Configuration.h" // ==> ALSO TRY ALL AVAILABLE LANGUAGE OPTIONS // See also http://marlinfw.org/docs/development/lcd_language.html @@ -367,15 +367,15 @@ #include INCLUDE_LANGUAGE -#if DISABLED(DISPLAY_CHARSET_ISO10646_1) \ - && DISABLED(DISPLAY_CHARSET_ISO10646_5) \ - && DISABLED(DISPLAY_CHARSET_ISO10646_KANA) \ - && DISABLED(DISPLAY_CHARSET_ISO10646_GREEK) \ - && DISABLED(DISPLAY_CHARSET_ISO10646_CN) \ - && DISABLED(DISPLAY_CHARSET_ISO10646_TR) \ - && DISABLED(DISPLAY_CHARSET_ISO10646_PL) \ - && DISABLED(DISPLAY_CHARSET_ISO10646_CZ) \ - && DISABLED(DISPLAY_CHARSET_ISO10646_SK) +#if NONE(DISPLAY_CHARSET_ISO10646_1, \ + DISPLAY_CHARSET_ISO10646_5, \ + DISPLAY_CHARSET_ISO10646_KANA, \ + DISPLAY_CHARSET_ISO10646_GREEK, \ + DISPLAY_CHARSET_ISO10646_CN, \ + DISPLAY_CHARSET_ISO10646_TR, \ + DISPLAY_CHARSET_ISO10646_PL, \ + DISPLAY_CHARSET_ISO10646_CZ, \ + DISPLAY_CHARSET_ISO10646_SK) #define DISPLAY_CHARSET_ISO10646_1 // use the better font on full graphic displays. #endif diff --git a/Marlin/src/core/macros.h b/Marlin/src/core/macros.h index 0f2609f459..a6e546a4a8 100644 --- a/Marlin/src/core/macros.h +++ b/Marlin/src/core/macros.h @@ -21,8 +21,6 @@ */ #pragma once -#include "minmax.h" - #define NUM_AXIS 4 #define ABCE 4 #define XYZE 4 @@ -75,10 +73,16 @@ #undef _BV #define _BV(n) (1<<(n)) #define TEST(n,b) !!((n)&_BV(b)) -#define SBI(n,b) (n |= _BV(b)) -#define CBI(n,b) (n &= ~_BV(b)) #define SET_BIT_TO(N,B,TF) do{ if (TF) SBI(N,B); else CBI(N,B); }while(0) +#ifndef SBI + #define SBI(A,B) (A |= (1 << (B))) +#endif + +#ifndef CBI + #define CBI(A,B) (A &= ~(1 << (B))) +#endif + #define _BV32(b) (1UL << (b)) #define TEST32(n,b) !!((n)&_BV32(b)) #define SBI32(n,b) (n |= _BV32(b)) @@ -190,7 +194,7 @@ #define ZERO(a) memset(a,0,sizeof(a)) #define COPY(a,b) do{ \ static_assert(sizeof(a[0]) == sizeof(b[0]), "COPY: '" STRINGIFY(a) "' and '" STRINGIFY(b) "' types (sizes) don't match!"); \ - memcpy(&a[0],&b[0],MIN(sizeof(a),sizeof(b))); \ + memcpy(&a[0],&b[0],_MIN(sizeof(a),sizeof(b))); \ }while(0) // Macros for initializing arrays @@ -269,3 +273,58 @@ #else #define I2C_ADDRESS(A) A #endif + +// Use NUM_ARGS(__VA_ARGS__) to get the number of variadic arguments +#define _NUM_ARGS(_0,_24_,_23,_22,_21,_20,_19,_18,_17,_16,_15,_14,_13,_12,_11,_10,_9,_8,_7,_6,_5,_4,_3,_2,_1,N,...) N +#define NUM_ARGS(V...) _NUM_ARGS(0,V,24,23,22,21,20,19,18,17,16,15,14,13,12,11,10,9,8,7,6,5,4,3,2,1,0) + +#ifdef __cplusplus + + #ifndef _MINMAX_H_ + #define _MINMAX_H_ + + extern "C++" { + + // C++11 solution that is standards compliant. Return type is deduced automatically + template static inline constexpr auto _MIN(const L lhs, const R rhs) -> decltype(lhs + rhs) { + return lhs < rhs ? lhs : rhs; + } + template static inline constexpr auto _MAX(const L lhs, const R rhs) -> decltype(lhs + rhs) { + return lhs > rhs ? lhs : rhs; + } + template static inline constexpr const T _MIN(T V, Ts... Vs) { return _MIN(V, _MIN(Vs...)); } + template static inline constexpr const T _MAX(T V, Ts... Vs) { return _MAX(V, _MAX(Vs...)); } + + } + + #endif + +#else + + #define MIN_2(a,b) ((a)<(b)?(a):(b)) + #define MIN_3(a,...) MIN_2(a,MIN_2(__VA_ARGS__)) + #define MIN_4(a,...) MIN_2(a,MIN_3(__VA_ARGS__)) + #define MIN_5(a,...) MIN_2(a,MIN_4(__VA_ARGS__)) + #define MIN_6(a,...) MIN_2(a,MIN_5(__VA_ARGS__)) + #define MIN_7(a,...) MIN_2(a,MIN_6(__VA_ARGS__)) + #define MIN_8(a,...) MIN_2(a,MIN_7(__VA_ARGS__)) + #define MIN_9(a,...) MIN_2(a,MIN_8(__VA_ARGS__)) + #define MIN_10(a,...) MIN_2(a,MIN_9(__VA_ARGS__)) + #define __MIN_N(N, ...) MIN_##N(__VA_ARGS__) + #define _MIN_N(N, ...) __MIN_N(N,__VA_ARGS__) + #define _MIN(...) _MIN_N(NUM_ARGS(__VA_ARGS__), __VA_ARGS__) + + #define MAX_2(a,b) ((a)>(b)?(a):(b)) + #define MAX_3(a,...) MAX_2(a,MAX_2(__VA_ARGS__)) + #define MAX_4(a,...) MAX_2(a,MAX_3(__VA_ARGS__)) + #define MAX_5(a,...) MAX_2(a,MAX_4(__VA_ARGS__)) + #define MAX_6(a,...) MAX_2(a,MAX_5(__VA_ARGS__)) + #define MAX_7(a,...) MAX_2(a,MAX_6(__VA_ARGS__)) + #define MAX_8(a,...) MAX_2(a,MAX_7(__VA_ARGS__)) + #define MAX_9(a,...) MAX_2(a,MAX_8(__VA_ARGS__)) + #define MAX_10(a,...) MAX_2(a,MAX_9(__VA_ARGS__)) + #define __MAX_N(N, ...) MAX_##N(__VA_ARGS__) + #define _MAX_N(N, ...) __MAX_N(N,__VA_ARGS__) + #define _MAX(...) _MAX_N(NUM_ARGS(__VA_ARGS__), __VA_ARGS__) + +#endif diff --git a/Marlin/src/core/minmax.h b/Marlin/src/core/minmax.h deleted file mode 100644 index 042119a7e1..0000000000 --- a/Marlin/src/core/minmax.h +++ /dev/null @@ -1,80 +0,0 @@ -/** - * Marlin 3D Printer Firmware - * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] - * - * Based on Sprinter and grbl. - * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm - * - * This program is free software: you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation, either version 3 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program. If not, see . - * - */ -#pragma once - -#undef MIN -#undef MAX - -// Use NUM_ARGS(__VA_ARGS__) to get the number of variadic arguments -#define _NUM_ARGS(_0,_24_,_23,_22,_21,_20,_19,_18,_17,_16,_15,_14,_13,_12,_11,_10,_9,_8,_7,_6,_5,_4,_3,_2,_1,N,...) N -#define NUM_ARGS(V...) _NUM_ARGS(0,V,24,23,22,21,20,19,18,17,16,15,14,13,12,11,10,9,8,7,6,5,4,3,2,1,0) - -#ifdef __cplusplus - - #ifndef _MINMAX_H_ - #define _MINMAX_H_ - - extern "C++" { - - // C++11 solution that is standards compliant. Return type is deduced automatically - template static inline constexpr auto MIN(const L lhs, const R rhs) -> decltype(lhs + rhs) { - return lhs < rhs ? lhs : rhs; - } - template static inline constexpr auto MAX(const L lhs, const R rhs) -> decltype(lhs + rhs) { - return lhs > rhs ? lhs : rhs; - } - template static inline constexpr const T MIN(T V, Ts... Vs) { return MIN(V, MIN(Vs...)); } - template static inline constexpr const T MAX(T V, Ts... Vs) { return MAX(V, MAX(Vs...)); } - - } - - #endif - -#else - - #define MIN_2(a,b) ((a)<(b)?(a):(b)) - #define MIN_3(a,...) MIN_2(a,MIN_2(__VA_ARGS__)) - #define MIN_4(a,...) MIN_2(a,MIN_3(__VA_ARGS__)) - #define MIN_5(a,...) MIN_2(a,MIN_4(__VA_ARGS__)) - #define MIN_6(a,...) MIN_2(a,MIN_5(__VA_ARGS__)) - #define MIN_7(a,...) MIN_2(a,MIN_6(__VA_ARGS__)) - #define MIN_8(a,...) MIN_2(a,MIN_7(__VA_ARGS__)) - #define MIN_9(a,...) MIN_2(a,MIN_8(__VA_ARGS__)) - #define MIN_10(a,...) MIN_2(a,MIN_9(__VA_ARGS__)) - #define __MIN_N(N, ...) MIN_##N(__VA_ARGS__) - #define _MIN_N(N, ...) __MIN_N(N,__VA_ARGS__) - #define MIN(...) _MIN_N(NUM_ARGS(__VA_ARGS__), __VA_ARGS__) - - #define MAX_2(a,b) ((a)>(b)?(a):(b)) - #define MAX_3(a,...) MAX_2(a,MAX_2(__VA_ARGS__)) - #define MAX_4(a,...) MAX_2(a,MAX_3(__VA_ARGS__)) - #define MAX_5(a,...) MAX_2(a,MAX_4(__VA_ARGS__)) - #define MAX_6(a,...) MAX_2(a,MAX_5(__VA_ARGS__)) - #define MAX_7(a,...) MAX_2(a,MAX_6(__VA_ARGS__)) - #define MAX_8(a,...) MAX_2(a,MAX_7(__VA_ARGS__)) - #define MAX_9(a,...) MAX_2(a,MAX_8(__VA_ARGS__)) - #define MAX_10(a,...) MAX_2(a,MAX_9(__VA_ARGS__)) - #define __MAX_N(N, ...) MAX_##N(__VA_ARGS__) - #define _MAX_N(N, ...) __MAX_N(N,__VA_ARGS__) - #define MAX(...) _MAX_N(NUM_ARGS(__VA_ARGS__), __VA_ARGS__) - -#endif diff --git a/Marlin/src/core/serial.h b/Marlin/src/core/serial.h index e466966698..bae554bccb 100644 --- a/Marlin/src/core/serial.h +++ b/Marlin/src/core/serial.h @@ -21,9 +21,7 @@ */ #pragma once -#include "../inc/MarlinConfigPre.h" -#include "../core/minmax.h" -#include HAL_PATH(../HAL, HAL.h) +#include "../inc/MarlinConfig.h" /** * Define debug bit-masks @@ -57,10 +55,12 @@ extern uint8_t marlin_debug_flags; if (!serial_port_index || serial_port_index == SERIAL_BOTH) (void)MYSERIAL0.WHAT(V); \ if ( serial_port_index) (void)MYSERIAL1.WHAT(V); \ }while(0) + #define SERIAL_ASSERT(P) if(serial_port_index!=(P)){ debugger(); } #else #define _PORT_REDIRECT(n,p) NOOP #define _PORT_RESTORE(n) NOOP #define SERIAL_OUT(WHAT, V...) (void)MYSERIAL0.WHAT(V) + #define SERIAL_ASSERT(P) NOOP #endif #define PORT_REDIRECT(p) _PORT_REDIRECT(1,p) @@ -68,11 +68,11 @@ extern uint8_t marlin_debug_flags; #define SERIAL_CHAR(x) SERIAL_OUT(write, x) #define SERIAL_ECHO(x) SERIAL_OUT(print, x) -#define SERIAL_ECHO_F(V...) SERIAL_OUT(print, V) +#define SERIAL_ECHO_F(V...) SERIAL_OUT(print, V) #define SERIAL_ECHOLN(x) SERIAL_OUT(println, x) #define SERIAL_PRINT(x,b) SERIAL_OUT(print, x, b) #define SERIAL_PRINTLN(x,b) SERIAL_OUT(println, x, b) -#define SERIAL_PRINTF(V...) SERIAL_OUT(printf, V) +#define SERIAL_PRINTF(V...) SERIAL_OUT(printf, V) #define SERIAL_FLUSH() SERIAL_OUT(flush) #if TX_BUFFER_SIZE > 0 diff --git a/Marlin/src/feature/I2CPositionEncoder.cpp b/Marlin/src/feature/I2CPositionEncoder.cpp index 254ba01eff..7d225b8e08 100644 --- a/Marlin/src/feature/I2CPositionEncoder.cpp +++ b/Marlin/src/feature/I2CPositionEncoder.cpp @@ -424,7 +424,6 @@ void I2CPositionEncoder::calibrate_steps_mm(const uint8_t iter) { travelledDistance = mm_from_count(ABS(stopCount - startCount)); SERIAL_ECHOLNPAIR("Attempted travel: ", travelDistance, "mm"); - SERIAL_ECHOLNPAIR(" Actual travel: ", travelledDistance, "mm"); //Calculate new axis steps per unit diff --git a/Marlin/src/feature/Max7219_Debug_LEDs.cpp b/Marlin/src/feature/Max7219_Debug_LEDs.cpp index fcfa208687..9ba67d6caa 100644 --- a/Marlin/src/feature/Max7219_Debug_LEDs.cpp +++ b/Marlin/src/feature/Max7219_Debug_LEDs.cpp @@ -48,6 +48,28 @@ #include "../Marlin.h" #include "../HAL/shared/Delay.h" +#define HAS_SIDE_BY_SIDE (ENABLED(MAX7219_SIDE_BY_SIDE) && MAX7219_NUMBER_UNITS > 1) + +#if _ROT == 0 || _ROT == 180 + #if HAS_SIDE_BY_SIDE + #define MAX7219_X_LEDS 8 + #define MAX7219_Y_LEDS MAX7219_LINES + #else + #define MAX7219_Y_LEDS 8 + #define MAX7219_X_LEDS MAX7219_LINES + #endif +#elif _ROT == 90 || _ROT == 270 + #if HAS_SIDE_BY_SIDE + #define MAX7219_Y_LEDS 8 + #define MAX7219_X_LEDS MAX7219_LINES + #else + #define MAX7219_X_LEDS 8 + #define MAX7219_Y_LEDS MAX7219_LINES + #endif +#else + #error "MAX7219_ROTATE must be a multiple of +/- 90°." +#endif + Max7219 max7219; uint8_t Max7219::led_line[MAX7219_LINES]; // = { 0 }; @@ -59,25 +81,41 @@ uint8_t Max7219::led_line[MAX7219_LINES]; // = { 0 }; #else #define _LED_BIT(Q) ((Q) & 0x7) #endif - -#if (_ROT == 0 || _ROT == 270) == ENABLED(MAX7219_REVERSE_ORDER) - #define _LED_UNIT(Q) ((MAX7219_NUMBER_UNITS - 1 - ((Q) >> 3)) << 3) -#else - #define _LED_UNIT(Q) ((Q) & ~0x7) -#endif - -#if _ROT < 180 - #define _LED_IND(P,Q) (_LED_UNIT(P) + (Q)) -#else - #define _LED_IND(P,Q) (_LED_UNIT(P) + (7 - ((Q) & 0x7))) -#endif #if _ROT == 0 || _ROT == 180 - #define LED_IND(X,Y) _LED_IND(X,Y) #define LED_BIT(X,Y) _LED_BIT(X) -#elif _ROT == 90 || _ROT == 270 - #define LED_IND(X,Y) _LED_IND(Y,X) +#else #define LED_BIT(X,Y) _LED_BIT(Y) #endif +#if _ROT == 0 || _ROT == 90 + #define _LED_IND(P,Q) (_LED_TOP(P) + ((Q) & 0x7)) +#else + #define _LED_IND(P,Q) (_LED_TOP(P) + (7 - ((Q) & 0x7))) +#endif + +#if HAS_SIDE_BY_SIDE + #if (_ROT == 0 || _ROT == 90) == DISABLED(MAX7219_REVERSE_ORDER) + #define _LED_TOP(Q) ((MAX7219_NUMBER_UNITS - 1 - ((Q) >> 3)) << 3) + #else + #define _LED_TOP(Q) ((Q) & ~0x7) + #endif + #if _ROT == 0 || _ROT == 180 + #define LED_IND(X,Y) _LED_IND(Y,Y) + #elif _ROT == 90 || _ROT == 270 + #define LED_IND(X,Y) _LED_IND(X,X) + #endif +#else + #if (_ROT == 0 || _ROT == 270) == DISABLED(MAX7219_REVERSE_ORDER) + #define _LED_TOP(Q) ((Q) & ~0x7) + #else + #define _LED_TOP(Q) ((MAX7219_NUMBER_UNITS - 1 - ((Q) >> 3)) << 3) + #endif + #if _ROT == 0 || _ROT == 180 + #define LED_IND(X,Y) _LED_IND(X,Y) + #elif _ROT == 90 || _ROT == 270 + #define LED_IND(X,Y) _LED_IND(Y,X) + #endif +#endif + #define XOR_7219(X,Y) do{ led_line[LED_IND(X,Y)] ^= _BV(LED_BIT(X,Y)); }while(0) #define SET_7219(X,Y) do{ led_line[LED_IND(X,Y)] |= _BV(LED_BIT(X,Y)); }while(0) #define CLR_7219(X,Y) do{ led_line[LED_IND(X,Y)] &= ~_BV(LED_BIT(X,Y)); }while(0) @@ -172,23 +210,31 @@ void Max7219::send(const uint8_t reg, const uint8_t data) { CRITICAL_SECTION_END; } -// Send out a single native row of bits to all units -void Max7219::refresh_line(const uint8_t line) { - for (uint8_t u = MAX7219_NUMBER_UNITS; u--;) - send(LINE_REG(line), led_line[(u << 3) | (line & 0x7)]); +// Send out a single native row of bits to just one unit +void Max7219::refresh_unit_line(const uint8_t line) { + #if MAX7219_NUMBER_UNITS == 1 + send(LINE_REG(line), led_line[line]); + #else + for (uint8_t u = MAX7219_NUMBER_UNITS; u--;) + if (u == (line >> 3)) send(LINE_REG(line), led_line[line]); else noop(); + #endif pulse_load(); } -// Send out a single native row of bits to just one unit -void Max7219::refresh_unit_line(const uint8_t line) { - for (uint8_t u = MAX7219_NUMBER_UNITS; u--;) - if (u == (line >> 3)) send(LINE_REG(line), led_line[line]); else noop(); +// Send out a single native row of bits to all units +void Max7219::refresh_line(const uint8_t line) { + #if MAX7219_NUMBER_UNITS == 1 + refresh_unit_line(line); + #else + for (uint8_t u = MAX7219_NUMBER_UNITS; u--;) + send(LINE_REG(line), led_line[(u << 3) | (line & 0x7)]); + #endif pulse_load(); } void Max7219::set(const uint8_t line, const uint8_t bits) { led_line[line] = bits; - refresh_line(line); + refresh_unit_line(line); } #if ENABLED(MAX7219_NUMERIC) @@ -227,42 +273,50 @@ void Max7219::set(const uint8_t line, const uint8_t bits) { // Modify a single LED bit and send the changed line void Max7219::led_set(const uint8_t x, const uint8_t y, const bool on) { - if (x > MAX7219_X_LEDS - 1 || y > MAX7219_Y_LEDS - 1) return error(PSTR("led_set"), x, y); + if (x >= MAX7219_X_LEDS || y >= MAX7219_Y_LEDS) return error(PSTR("led_set"), x, y); if (BIT_7219(x, y) == on) return; XOR_7219(x, y); - refresh_line(LED_IND(x, y)); + refresh_unit_line(LED_IND(x, y)); } void Max7219::led_on(const uint8_t x, const uint8_t y) { - if (x > MAX7219_X_LEDS - 1 || y > MAX7219_Y_LEDS - 1) return error(PSTR("led_on"), x, y); + if (x >= MAX7219_X_LEDS || y >= MAX7219_Y_LEDS) return error(PSTR("led_on"), x, y); led_set(x, y, true); } void Max7219::led_off(const uint8_t x, const uint8_t y) { - if (x > MAX7219_X_LEDS - 1 || y > MAX7219_Y_LEDS - 1) return error(PSTR("led_off"), x, y); + if (x >= MAX7219_X_LEDS || y >= MAX7219_Y_LEDS) return error(PSTR("led_off"), x, y); led_set(x, y, false); } void Max7219::led_toggle(const uint8_t x, const uint8_t y) { - if (x > MAX7219_X_LEDS - 1 || y > MAX7219_Y_LEDS - 1) return error(PSTR("led_toggle"), x, y); + if (x >= MAX7219_X_LEDS || y >= MAX7219_Y_LEDS) return error(PSTR("led_toggle"), x, y); led_set(x, y, !BIT_7219(x, y)); } void Max7219::send_row(const uint8_t row) { - #if _ROT == 0 || _ROT == 180 - refresh_line(LED_IND(0, row)); - #else + #if _ROT == 0 || _ROT == 180 // Native Lines are horizontal too + #if MAX7219_X_LEDS <= 8 + refresh_unit_line(LED_IND(0, row)); // A single unit line + #else + refresh_line(LED_IND(0, row)); // Same line, all units + #endif + #else // Native lines are vertical UNUSED(row); - refresh(); + refresh(); // Actually a column #endif } void Max7219::send_column(const uint8_t col) { - #if _ROT == 90 || _ROT == 270 - refresh_line(LED_IND(col, 0)); - #else + #if _ROT == 90 || _ROT == 270 // Native Lines are vertical too + #if MAX7219_Y_LEDS <= 8 + refresh_unit_line(LED_IND(col, 0)); // A single unit line + #else + refresh_line(LED_IND(col, 0)); // Same line, all units + #endif + #else // Native lines are horizontal UNUSED(col); - refresh(); + refresh(); // Actually a row #endif } @@ -378,24 +432,24 @@ void Max7219::set_columns_32bits(const uint8_t x, uint32_t val) { void Max7219::register_setup() { for (uint8_t i = 0; i < MAX7219_NUMBER_UNITS; i++) send(max7219_reg_scanLimit, 0x07); - pulse_load(); // tell the chips to load the clocked out data + pulse_load(); // Tell the chips to load the clocked out data for (uint8_t i = 0; i < MAX7219_NUMBER_UNITS; i++) - send(max7219_reg_decodeMode, 0x00); // using an led matrix (not digits) - pulse_load(); // tell the chips to load the clocked out data + send(max7219_reg_decodeMode, 0x00); // Using an led matrix (not digits) + pulse_load(); // Tell the chips to load the clocked out data for (uint8_t i = 0; i < MAX7219_NUMBER_UNITS; i++) - send(max7219_reg_shutdown, 0x01); // not in shutdown mode - pulse_load(); // tell the chips to load the clocked out data + send(max7219_reg_shutdown, 0x01); // Not in shutdown mode + pulse_load(); // Tell the chips to load the clocked out data for (uint8_t i = 0; i < MAX7219_NUMBER_UNITS; i++) - send(max7219_reg_displayTest, 0x00); // no display test - pulse_load(); // tell the chips to load the clocked out data + send(max7219_reg_displayTest, 0x00); // No display test + pulse_load(); // Tell the chips to load the clocked out data for (uint8_t i = 0; i < MAX7219_NUMBER_UNITS; i++) - send(max7219_reg_intensity, 0x01 & 0x0F); // the first 0x0F is the value you can set - // range: 0x00 to 0x0F - pulse_load(); // tell the chips to load the clocked out data + send(max7219_reg_intensity, 0x01 & 0x0F); // The first 0x0F is the value you can set + // Range: 0x00 to 0x0F + pulse_load(); // Tell the chips to load the clocked out data } #ifdef MAX7219_INIT_TEST @@ -408,7 +462,7 @@ void Max7219::register_setup() { led_set(px, py, on); delay(del); const int8_t x = px + way[dir], y = py + way[dir + 1]; - if (!WITHIN(x, 0, MAX7219_X_LEDS-1) || !WITHIN(y, 0, MAX7219_Y_LEDS-1) || BIT_7219(x, y) == on) dir = (dir + 2) & 0x7; + if (!WITHIN(x, 0, MAX7219_X_LEDS - 1) || !WITHIN(y, 0, MAX7219_Y_LEDS - 1) || BIT_7219(x, y) == on) dir = (dir + 2) & 0x7; px += way[dir]; py += way[dir + 1]; } } @@ -416,7 +470,7 @@ void Max7219::register_setup() { #else void Max7219::sweep(const int8_t dir, const uint16_t ms, const bool on) { - uint8_t x = dir > 0 ? 0 : MAX7219_X_LEDS-1; + uint8_t x = dir > 0 ? 0 : MAX7219_X_LEDS - 1; for (uint8_t i = MAX7219_X_LEDS; i--; x += dir) { set_column(x, on ? 0xFFFFFFFF : 0x00000000); delay(ms); @@ -434,10 +488,10 @@ void Max7219::init() { register_setup(); - for (uint8_t i = 0; i <= 7; i++) { // Empty registers to turn all LEDs off + for (uint8_t i = 0; i <= 7; i++) { // Empty registers to turn all LEDs off led_line[i] = 0x00; send(max7219_reg_digit0 + i, 0); - pulse_load(); // tell the chips to load the clocked out data + pulse_load(); // Tell the chips to load the clocked out data } #ifdef MAX7219_INIT_TEST @@ -464,55 +518,52 @@ void Max7219::init() { */ // Apply changes to update a marker -void Max7219::mark16(const uint8_t y, const uint8_t v1, const uint8_t v2) { - #if MAX7219_X_LEDS == 8 - #if MAX7219_Y_LEDS == 8 - led_off(v1 & 0x7, y + (v1 >= 8)); - led_on(v2 & 0x7, y + (v2 >= 8)); - #else - led_off(y, v1 & 0xF); // At least 16 LEDs down. Use a single column. - led_on(y, v2 & 0xF); - #endif - #else - led_off(v1 & 0xF, y); // At least 16 LEDs across. Use a single row. - led_on(v2 & 0xF, y); +void Max7219::mark16(const uint8_t pos, const uint8_t v1, const uint8_t v2) { + #if MAX7219_X_LEDS > 8 // At least 16 LEDs on the X-Axis. Use single line. + led_off(v1 & 0xF, pos); + led_on(v2 & 0xF, pos); + #elif MAX7219_Y_LEDS > 8 // At least 16 LEDs on the Y-Axis. Use a single column. + led_off(pos, v1 & 0xF); + led_on(pos, v2 & 0xF); + #else // Single 8x8 LED matrix. Use two lines to get 16 LEDs. + led_off(v1 & 0x7, pos + (v1 >= 8)); + led_on(v2 & 0x7, pos + (v2 >= 8)); #endif } // Apply changes to update a tail-to-head range void Max7219::range16(const uint8_t y, const uint8_t ot, const uint8_t nt, const uint8_t oh, const uint8_t nh) { - #if MAX7219_X_LEDS == 8 - #if MAX7219_Y_LEDS == 8 - if (ot != nt) for (uint8_t n = ot & 0xF; n != (nt & 0xF) && n != (nh & 0xF); n = (n + 1) & 0xF) - led_off(n & 0x7, y + (n >= 8)); - if (oh != nh) for (uint8_t n = (oh + 1) & 0xF; n != ((nh + 1) & 0xF); n = (n + 1) & 0xF) - led_on(n & 0x7, y + (n >= 8)); - #else // The Max7219 Y-Axis has at least 16 LED's. So use a single column - if (ot != nt) for (uint8_t n = ot & 0xF; n != (nt & 0xF) && n != (nh & 0xF); n = (n + 1) & 0xF) - led_off(y, n & 0xF); - if (oh != nh) for (uint8_t n = (oh + 1) & 0xF; n != ((nh + 1) & 0xF); n = (n + 1) & 0xF) - led_on(y, n & 0xF); - #endif - #else // LED matrix has at least 16 LED's on the X-Axis. Use single line of LED's + #if MAX7219_X_LEDS > 8 // At least 16 LEDs on the X-Axis. Use single line. if (ot != nt) for (uint8_t n = ot & 0xF; n != (nt & 0xF) && n != (nh & 0xF); n = (n + 1) & 0xF) led_off(n & 0xF, y); if (oh != nh) for (uint8_t n = (oh + 1) & 0xF; n != ((nh + 1) & 0xF); n = (n + 1) & 0xF) led_on(n & 0xF, y); - #endif + #elif MAX7219_Y_LEDS > 8 // At least 16 LEDs on the Y-Axis. Use a single column. + if (ot != nt) for (uint8_t n = ot & 0xF; n != (nt & 0xF) && n != (nh & 0xF); n = (n + 1) & 0xF) + led_off(y, n & 0xF); + if (oh != nh) for (uint8_t n = (oh + 1) & 0xF; n != ((nh + 1) & 0xF); n = (n + 1) & 0xF) + led_on(y, n & 0xF); + #else // Single 8x8 LED matrix. Use two lines to get 16 LEDs. + if (ot != nt) for (uint8_t n = ot & 0xF; n != (nt & 0xF) && n != (nh & 0xF); n = (n + 1) & 0xF) + led_off(n & 0x7, y + (n >= 8)); + if (oh != nh) for (uint8_t n = (oh + 1) & 0xF; n != ((nh + 1) & 0xF); n = (n + 1) & 0xF) + led_on(n & 0x7, y + (n >= 8)); + #endif } // Apply changes to update a quantity -void Max7219::quantity16(const uint8_t y, const uint8_t ov, const uint8_t nv) { - for (uint8_t i = MIN(nv, ov); i < MAX(nv, ov); i++) - #if MAX7219_X_LEDS == 8 - #if MAX7219_Y_LEDS == 8 - led_set(i >> 1, y + (i & 1), nv >= ov); // single 8x8 LED matrix. Use two lines to get 16 LED's - #else - led_set(y, i, nv >= ov); // The Max7219 Y-Axis has at least 16 LED's. So use a single column +void Max7219::quantity16(const uint8_t pos, const uint8_t ov, const uint8_t nv) { + for (uint8_t i = _MIN(nv, ov); i < _MAX(nv, ov); i++) + led_set( + #if MAX7219_X_LEDS > 8 // At least 16 LEDs on the X-Axis. Use single line. + i, pos + #elif MAX7219_Y_LEDS > 8 // At least 16 LEDs on the Y-Axis. Use a single column. + pos, i + #else // Single 8x8 LED matrix. Use two lines to get 16 LEDs. + i >> 1, pos + (i & 1) #endif - #else - led_set(i, y, nv >= ov); // LED matrix has at least 16 LED's on the X-Axis. Use single line of LED's - #endif + , nv >= ov + ); } void Max7219::idle_tasks() { diff --git a/Marlin/src/feature/Max7219_Debug_LEDs.h b/Marlin/src/feature/Max7219_Debug_LEDs.h index 17b2dfb474..02f7c1888b 100644 --- a/Marlin/src/feature/Max7219_Debug_LEDs.h +++ b/Marlin/src/feature/Max7219_Debug_LEDs.h @@ -41,7 +41,6 @@ * faster to do a Max7219_Set_Column() with a rotation of 90 or 270 degrees than to do * a Max7219_Set_Row(). The opposite is true for rotations of 0 or 180 degrees. */ -#pragma once #ifndef MAX7219_ROTATE #define MAX7219_ROTATE 0 @@ -53,16 +52,6 @@ #endif #define MAX7219_LINES (8 * (MAX7219_NUMBER_UNITS)) -#if _ROT == 0 || _ROT == 180 - #define MAX7219_Y_LEDS 8 - #define MAX7219_X_LEDS MAX7219_LINES -#elif _ROT == 90 || _ROT == 270 - #define MAX7219_X_LEDS 8 - #define MAX7219_Y_LEDS MAX7219_LINES -#else - #error "MAX7219_ROTATE must be a multiple of +/- 90°." -#endif - // // MAX7219 registers // diff --git a/Marlin/src/feature/backlash.cpp b/Marlin/src/feature/backlash.cpp index 772d823b7b..8f708c14f6 100644 --- a/Marlin/src/feature/backlash.cpp +++ b/Marlin/src/feature/backlash.cpp @@ -106,7 +106,7 @@ void Backlash::add_correction_steps(const int32_t &da, const int32_t &db, const // the current segment travels in the same direction as the correction if (reversing == (error_correction < 0)) { if (segment_proportion == 0) - segment_proportion = MIN(1.0f, block->millimeters / smoothing_mm); + segment_proportion = _MIN(1.0f, block->millimeters / smoothing_mm); error_correction = CEIL(segment_proportion * error_correction); } else diff --git a/Marlin/src/feature/backlash.h b/Marlin/src/feature/backlash.h index fd220a4914..e86955b95b 100644 --- a/Marlin/src/feature/backlash.h +++ b/Marlin/src/feature/backlash.h @@ -41,7 +41,7 @@ public: #ifdef BACKLASH_SMOOTHING_MM static float smoothing_mm; #endif - static inline void set_correction(const float &v) { correction = MAX(0, MIN(1.0, v)) * all_on; } + static inline void set_correction(const float &v) { correction = _MAX(0, _MIN(1.0, v)) * all_on; } static inline float get_correction() { return float(ui8_to_percent(correction)) / 100.0f; } #else static constexpr uint8_t correction = (BACKLASH_CORRECTION) * 0xFF; diff --git a/Marlin/src/feature/bedlevel/abl/abl.cpp b/Marlin/src/feature/bedlevel/abl/abl.cpp index 37a19b8c01..c70cf62203 100644 --- a/Marlin/src/feature/bedlevel/abl/abl.cpp +++ b/Marlin/src/feature/bedlevel/abl/abl.cpp @@ -301,7 +301,7 @@ float bilinear_z_offset(const float raw[XYZ]) { #endif gridx = gx; - nextx = MIN(gridx + 1, ABL_BG_POINTS_X - 1); + nextx = _MIN(gridx + 1, ABL_BG_POINTS_X - 1); } if (last_y != ry || last_gridx != gridx) { @@ -318,7 +318,7 @@ float bilinear_z_offset(const float raw[XYZ]) { #endif gridy = gy; - nexty = MIN(gridy + 1, ABL_BG_POINTS_Y - 1); + nexty = _MIN(gridy + 1, ABL_BG_POINTS_Y - 1); } if (last_gridx != gridx || last_gridy != gridy) { @@ -369,10 +369,10 @@ float bilinear_z_offset(const float raw[XYZ]) { cy1 = CELL_INDEX(Y, current_position[Y_AXIS]), cx2 = CELL_INDEX(X, destination[X_AXIS]), cy2 = CELL_INDEX(Y, destination[Y_AXIS]); - cx1 = constrain(cx1, 0, ABL_BG_POINTS_X - 2); - cy1 = constrain(cy1, 0, ABL_BG_POINTS_Y - 2); - cx2 = constrain(cx2, 0, ABL_BG_POINTS_X - 2); - cy2 = constrain(cy2, 0, ABL_BG_POINTS_Y - 2); + LIMIT(cx1, 0, ABL_BG_POINTS_X - 2); + LIMIT(cy1, 0, ABL_BG_POINTS_Y - 2); + LIMIT(cx2, 0, ABL_BG_POINTS_X - 2); + LIMIT(cy2, 0, ABL_BG_POINTS_Y - 2); // Start and end in the same cell? No split needed. if (cx1 == cx2 && cy1 == cy2) { @@ -384,7 +384,7 @@ float bilinear_z_offset(const float raw[XYZ]) { #define LINE_SEGMENT_END(A) (current_position[_AXIS(A)] + (destination[_AXIS(A)] - current_position[_AXIS(A)]) * normalized_dist) float normalized_dist, end[XYZE]; - const int8_t gcx = MAX(cx1, cx2), gcy = MAX(cy1, cy2); + const int8_t gcx = _MAX(cx1, cx2), gcy = _MAX(cy1, cy2); // Crosses on the X and not already split on this X? // The x_splits flags are insurance against rounding errors. diff --git a/Marlin/src/feature/bedlevel/bedlevel.cpp b/Marlin/src/feature/bedlevel/bedlevel.cpp index 5e18d13260..e6bc47a62b 100644 --- a/Marlin/src/feature/bedlevel/bedlevel.cpp +++ b/Marlin/src/feature/bedlevel/bedlevel.cpp @@ -100,6 +100,10 @@ void set_bed_leveling_enabled(const bool enable/*=true*/) { } } +TemporaryBedLevelingState::TemporaryBedLevelingState(const bool enable) : saved(planner.leveling_active) { + set_bed_leveling_enabled(enable); +} + #if ENABLED(ENABLE_LEVELING_FADE_HEIGHT) void set_z_fade_height(const float zfh, const bool do_report/*=true*/) { @@ -222,9 +226,9 @@ void reset_bed_level() { #ifdef MANUAL_PROBE_START_Z #if MANUAL_PROBE_HEIGHT > 0 do_blocking_move_to(rx, ry, MANUAL_PROBE_HEIGHT); - do_blocking_move_to_z(MAX(0,MANUAL_PROBE_START_Z)); + do_blocking_move_to_z(_MAX(0,MANUAL_PROBE_START_Z)); #else - do_blocking_move_to(rx, ry, MAX(0,MANUAL_PROBE_START_Z)); + do_blocking_move_to(rx, ry, _MAX(0,MANUAL_PROBE_START_Z)); #endif #elif MANUAL_PROBE_HEIGHT > 0 const float prev_z = current_position[Z_AXIS]; diff --git a/Marlin/src/feature/bedlevel/bedlevel.h b/Marlin/src/feature/bedlevel/bedlevel.h index 82957c4884..e5f0db47f7 100644 --- a/Marlin/src/feature/bedlevel/bedlevel.h +++ b/Marlin/src/feature/bedlevel/bedlevel.h @@ -46,6 +46,18 @@ void reset_bed_level(); void _manual_goto_xy(const float &x, const float &y); #endif +/** + * A class to save and change the bed leveling state, + * then restore it when it goes out of scope. + */ +class TemporaryBedLevelingState { + bool saved; + public: + TemporaryBedLevelingState(const bool enable); + ~TemporaryBedLevelingState() { set_bed_leveling_enabled(saved); } +}; +#define TEMPORARY_BED_LEVELING_STATE(enable) TemporaryBedLevelingState tbls(enable) + #if HAS_MESH typedef float (&bed_mesh_t)[GRID_MAX_POINTS_X][GRID_MAX_POINTS_Y]; diff --git a/Marlin/src/feature/bedlevel/mbl/mesh_bed_leveling.cpp b/Marlin/src/feature/bedlevel/mbl/mesh_bed_leveling.cpp index 4013b9c482..6a9deaed9b 100644 --- a/Marlin/src/feature/bedlevel/mbl/mesh_bed_leveling.cpp +++ b/Marlin/src/feature/bedlevel/mbl/mesh_bed_leveling.cpp @@ -29,6 +29,10 @@ #include "../../../module/motion.h" #include "../../../feature/bedlevel/bedlevel.h" + #if ENABLED(EXTENSIBLE_UI) + #include "../../../lcd/extensible_ui/ui_api.h" + #endif + mesh_bed_leveling mbl; float mesh_bed_leveling::z_offset, @@ -81,7 +85,7 @@ #define MBL_SEGMENT_END(A) (current_position[_AXIS(A)] + (destination[_AXIS(A)] - current_position[_AXIS(A)]) * normalized_dist) float normalized_dist, end[XYZE]; - const int8_t gcx = MAX(cx1, cx2), gcy = MAX(cy1, cy2); + const int8_t gcx = _MAX(cx1, cx2), gcy = _MAX(cy1, cy2); // Crosses on the X and not already split on this X? // The x_splits flags are insurance against rounding errors. diff --git a/Marlin/src/feature/bedlevel/ubl/ubl.cpp b/Marlin/src/feature/bedlevel/ubl/ubl.cpp index 1b7bebfa61..ee8fb48c9d 100644 --- a/Marlin/src/feature/bedlevel/ubl/ubl.cpp +++ b/Marlin/src/feature/bedlevel/ubl/ubl.cpp @@ -50,7 +50,7 @@ if (!isnan(z_values[x][y])) { SERIAL_ECHO_START(); SERIAL_ECHOPAIR(" M421 I", x, " J", y); - SERIAL_ECHOPAIR_F(" Z", z_values[x][y], 2); + SERIAL_ECHOPAIR_F(" Z", z_values[x][y], 4); SERIAL_EOL(); serial_delay(75); // Prevent Printrun from exploding } diff --git a/Marlin/src/feature/bedlevel/ubl/ubl.h b/Marlin/src/feature/bedlevel/ubl/ubl.h index 927f1fcb79..20ff9b0779 100644 --- a/Marlin/src/feature/bedlevel/ubl/ubl.h +++ b/Marlin/src/feature/bedlevel/ubl/ubl.h @@ -213,7 +213,7 @@ class unified_bed_leveling { const float xratio = (rx0 - mesh_index_to_xpos(x1_i)) * (1.0f / (MESH_X_DIST)), z1 = z_values[x1_i][yi]; - return z1 + xratio * (z_values[MIN(x1_i, GRID_MAX_POINTS_X - 2) + 1][yi] - z1); // Don't allow x1_i+1 to be past the end of the array + return z1 + xratio * (z_values[_MIN(x1_i, GRID_MAX_POINTS_X - 2) + 1][yi] - z1); // Don't allow x1_i+1 to be past the end of the array // If it is, it is clamped to the last element of the // z_values[][] array and no correction is applied. } @@ -242,7 +242,7 @@ class unified_bed_leveling { const float yratio = (ry0 - mesh_index_to_ypos(y1_i)) * (1.0f / (MESH_Y_DIST)), z1 = z_values[xi][y1_i]; - return z1 + yratio * (z_values[xi][MIN(y1_i, GRID_MAX_POINTS_Y - 2) + 1] - z1); // Don't allow y1_i+1 to be past the end of the array + return z1 + yratio * (z_values[xi][_MIN(y1_i, GRID_MAX_POINTS_Y - 2) + 1] - z1); // Don't allow y1_i+1 to be past the end of the array // If it is, it is clamped to the last element of the // z_values[][] array and no correction is applied. } @@ -268,11 +268,11 @@ class unified_bed_leveling { const float z1 = calc_z0(rx0, mesh_index_to_xpos(cx), z_values[cx][cy], - mesh_index_to_xpos(cx + 1), z_values[MIN(cx, GRID_MAX_POINTS_X - 2) + 1][cy]); + mesh_index_to_xpos(cx + 1), z_values[_MIN(cx, GRID_MAX_POINTS_X - 2) + 1][cy]); const float z2 = calc_z0(rx0, - mesh_index_to_xpos(cx), z_values[cx][MIN(cy, GRID_MAX_POINTS_Y - 2) + 1], - mesh_index_to_xpos(cx + 1), z_values[MIN(cx, GRID_MAX_POINTS_X - 2) + 1][MIN(cy, GRID_MAX_POINTS_Y - 2) + 1]); + mesh_index_to_xpos(cx), z_values[cx][_MIN(cy, GRID_MAX_POINTS_Y - 2) + 1], + mesh_index_to_xpos(cx + 1), z_values[_MIN(cx, GRID_MAX_POINTS_X - 2) + 1][_MIN(cy, GRID_MAX_POINTS_Y - 2) + 1]); float z0 = calc_z0(ry0, mesh_index_to_ypos(cy), z1, diff --git a/Marlin/src/feature/bedlevel/ubl/ubl_G29.cpp b/Marlin/src/feature/bedlevel/ubl/ubl_G29.cpp index afbbf313ad..568f766150 100644 --- a/Marlin/src/feature/bedlevel/ubl/ubl_G29.cpp +++ b/Marlin/src/feature/bedlevel/ubl/ubl_G29.cpp @@ -752,17 +752,19 @@ save_ubl_active_state_and_disable(); // No bed level correction so only raw data is obtained DEPLOY_PROBE(); - uint16_t count = GRID_MAX_POINTS, current = 1; + uint8_t count = GRID_MAX_POINTS, current = 1; do { current = (GRID_MAX_POINTS) - count + 1; if (do_ubl_mesh_map) display_map(g29_map_type); - SERIAL_ECHOLNPAIR("\nProbing mesh point ", current, "/", GRID_MAX_POINTS, ".\n"); - #if HAS_LCD_MENU - ui.status_printf_P(0, PSTR(MSG_LCD_PROBING_MESH " %i/%i"), current, int(GRID_MAX_POINTS)); + SERIAL_ECHOLNPAIR("\nProbing mesh point ", int(current), "/", int(GRID_MAX_POINTS), ".\n"); + #if HAS_DISPLAY + ui.status_printf_P(0, PSTR(MSG_PROBING_MESH " %i/%i"), int(current), int(GRID_MAX_POINTS)); + #endif + #if HAS_LCD_MENU if (ui.button_pressed()) { ui.quick_feedback(false); // Preserve button state for click-and-hold SERIAL_ECHOLNPGM("\nMesh only partially populated.\n"); @@ -855,7 +857,7 @@ save_ubl_active_state_and_disable(); // Disable bed level correction for probing do_blocking_move_to(0.5f * (MESH_MAX_X - (MESH_MIN_X)), 0.5f * (MESH_MAX_Y - (MESH_MIN_Y)), in_height); - //, MIN(planner.settings.max_feedrate_mm_s[X_AXIS], planner.settings.max_feedrate_mm_s[Y_AXIS]) * 0.5f); + //, _MIN(planner.settings.max_feedrate_mm_s[X_AXIS], planner.settings.max_feedrate_mm_s[Y_AXIS]) * 0.5f); planner.synchronize(); SERIAL_ECHOPGM("Place shim under nozzle"); @@ -1385,10 +1387,10 @@ #include "../../../libs/vector_3.h" void unified_bed_leveling::tilt_mesh_based_on_probed_grid(const bool do_3_pt_leveling) { - constexpr int16_t x_min = MAX(MIN_PROBE_X, MESH_MIN_X), - x_max = MIN(MAX_PROBE_X, MESH_MAX_X), - y_min = MAX(MIN_PROBE_Y, MESH_MIN_Y), - y_max = MIN(MAX_PROBE_Y, MESH_MAX_Y); + constexpr int16_t x_min = _MAX(MIN_PROBE_X, MESH_MIN_X), + x_max = _MIN(MAX_PROBE_X, MESH_MAX_X), + y_min = _MAX(MIN_PROBE_Y, MESH_MIN_Y), + y_max = _MIN(MAX_PROBE_Y, MESH_MAX_Y); bool abort_flag = false; @@ -1405,7 +1407,7 @@ if (do_3_pt_leveling) { SERIAL_ECHOLNPGM("Tilting mesh (1/3)"); - #if HAS_LCD_MENU + #if HAS_DISPLAY ui.status_printf_P(0, PSTR(MSG_LCD_TILTING_MESH " 1/3")); #endif @@ -1424,7 +1426,7 @@ if (!abort_flag) { SERIAL_ECHOLNPGM("Tilting mesh (2/3)"); - #if HAS_LCD_MENU + #if HAS_DISPLAY ui.status_printf_P(0, PSTR(MSG_LCD_TILTING_MESH " 2/3")); #endif @@ -1444,7 +1446,7 @@ if (!abort_flag) { SERIAL_ECHOLNPGM("Tilting mesh (3/3)"); - #if HAS_LCD_MENU + #if HAS_DISPLAY ui.status_printf_P(0, PSTR(MSG_LCD_TILTING_MESH " 3/3")); #endif @@ -1485,7 +1487,7 @@ if (!abort_flag) { SERIAL_ECHOLNPAIR("Tilting mesh point ", current, "/", total_points, "\n"); - #if HAS_LCD_MENU + #if HAS_DISPLAY ui.status_printf_P(0, PSTR(MSG_LCD_TILTING_MESH " %i/%i"), current, total_points); #endif @@ -1654,7 +1656,7 @@ SERIAL_ECHOPGM("Extrapolating mesh..."); - const float weight_scaled = weight_factor * MAX(MESH_X_DIST, MESH_Y_DIST); + const float weight_scaled = weight_factor * _MAX(MESH_X_DIST, MESH_Y_DIST); for (uint8_t jx = 0; jx < GRID_MAX_POINTS_X; jx++) for (uint8_t jy = 0; jy < GRID_MAX_POINTS_Y; jy++) diff --git a/Marlin/src/feature/bedlevel/ubl/ubl_motion.cpp b/Marlin/src/feature/bedlevel/ubl/ubl_motion.cpp index d3b012da5a..4bb29d7e0b 100644 --- a/Marlin/src/feature/bedlevel/ubl/ubl_motion.cpp +++ b/Marlin/src/feature/bedlevel/ubl/ubl_motion.cpp @@ -443,8 +443,8 @@ int8_t cell_xi = (raw[X_AXIS] - (MESH_MIN_X)) * (1.0f / (MESH_X_DIST)), cell_yi = (raw[Y_AXIS] - (MESH_MIN_Y)) * (1.0f / (MESH_Y_DIST)); - cell_xi = constrain(cell_xi, 0, (GRID_MAX_POINTS_X) - 1); - cell_yi = constrain(cell_yi, 0, (GRID_MAX_POINTS_Y) - 1); + LIMIT(cell_xi, 0, (GRID_MAX_POINTS_X) - 1); + LIMIT(cell_yi, 0, (GRID_MAX_POINTS_Y) - 1); const float x0 = mesh_index_to_xpos(cell_xi), // 64 byte table lookup avoids mul+add y0 = mesh_index_to_ypos(cell_yi); diff --git a/Marlin/src/feature/bltouch.cpp b/Marlin/src/feature/bltouch.cpp index fd26d66130..b768fc3e80 100644 --- a/Marlin/src/feature/bltouch.cpp +++ b/Marlin/src/feature/bltouch.cpp @@ -40,7 +40,7 @@ void stop(); bool BLTouch::command(const BLTCommand cmd, const millis_t &ms) { if (DEBUGGING(LEVELING)) SERIAL_ECHOLNPAIR("BLTouch Command :", cmd); MOVE_SERVO(Z_PROBE_SERVO_NR, cmd); - safe_delay(MAX(ms, (uint32_t)BLTOUCH_DELAY)); // BLTOUCH_DELAY is also the *minimum* delay + safe_delay(_MAX(ms, (uint32_t)BLTOUCH_DELAY)); // BLTOUCH_DELAY is also the *minimum* delay return triggered(); } diff --git a/Marlin/src/feature/dac/dac_mcp4728.cpp b/Marlin/src/feature/dac/dac_mcp4728.cpp index 0bfbaa3038..cfe36dd39f 100644 --- a/Marlin/src/feature/dac/dac_mcp4728.cpp +++ b/Marlin/src/feature/dac/dac_mcp4728.cpp @@ -108,7 +108,7 @@ uint16_t mcp4728_getValue(const uint8_t channel) { return mcp4728_values[channel uint16_t mcp4728_getVout(const uint8_t channel) { const uint32_t vref = 2048, vOut = (vref * mcp4728_values[channel] * (_DAC_STEPPER_GAIN + 1)) / 4096; - return MIN(vOut, defaultVDD); + return _MIN(vOut, defaultVDD); } #endif diff --git a/Marlin/src/feature/digipot/digipot_mcp4018.cpp b/Marlin/src/feature/digipot/digipot_mcp4018.cpp index fc02cf9ba9..91a64d5432 100644 --- a/Marlin/src/feature/digipot/digipot_mcp4018.cpp +++ b/Marlin/src/feature/digipot/digipot_mcp4018.cpp @@ -87,7 +87,7 @@ static void i2c_send(const uint8_t channel, const byte v) { // This is for the MCP4018 I2C based digipot void digipot_i2c_set_current(const uint8_t channel, const float current) { - i2c_send(channel, current_to_wiper(MIN(MAX(current, 0), float(DIGIPOT_A4988_MAX_CURRENT)))); + i2c_send(channel, current_to_wiper(_MIN(_MAX(current, 0), float(DIGIPOT_A4988_MAX_CURRENT)))); } void digipot_i2c_init() { diff --git a/Marlin/src/feature/digipot/digipot_mcp4451.cpp b/Marlin/src/feature/digipot/digipot_mcp4451.cpp index 6d7328b5f0..61140d81b5 100644 --- a/Marlin/src/feature/digipot/digipot_mcp4451.cpp +++ b/Marlin/src/feature/digipot/digipot_mcp4451.cpp @@ -72,7 +72,7 @@ void digipot_i2c_set_current(const uint8_t channel, const float current) { // Set actual wiper value byte addresses[4] = { 0x00, 0x10, 0x60, 0x70 }; - i2c_send(addr, addresses[channel & 0x3], current_to_wiper(MIN((float) MAX(current, 0), DIGIPOT_I2C_MAX_CURRENT))); + i2c_send(addr, addresses[channel & 0x3], current_to_wiper(MIN((float) _MAX(current, 0), DIGIPOT_I2C_MAX_CURRENT))); } void digipot_i2c_init() { diff --git a/Marlin/src/feature/host_actions.cpp b/Marlin/src/feature/host_actions.cpp index be26586984..b39b0fbc3c 100644 --- a/Marlin/src/feature/host_actions.cpp +++ b/Marlin/src/feature/host_actions.cpp @@ -37,8 +37,6 @@ #include "runout.h" #endif -extern bool wait_for_user; - void host_action(const char * const pstr, const bool eol) { SERIAL_ECHOPGM("//action:"); serialprintPGM(pstr); @@ -66,6 +64,10 @@ void host_action(const char * const pstr, const bool eol) { #if ENABLED(HOST_PROMPT_SUPPORT) + #if HAS_RESUME_CONTINUE + extern bool wait_for_user; + #endif + PromptReason host_prompt_reason = PROMPT_NOT_DEFINED; void host_action_prompt(const char * const ptype, const bool eol=true) { @@ -110,7 +112,9 @@ void host_action(const char * const pstr, const bool eol) { case PROMPT_FILAMENT_RUNOUT: msg = PSTR("FILAMENT_RUNOUT"); if (response == 0) { - pause_menu_response = PAUSE_RESPONSE_EXTRUDE_MORE; + #if ENABLED(ADVANCED_PAUSE_FEATURE) + pause_menu_response = PAUSE_RESPONSE_EXTRUDE_MORE; + #endif host_action_prompt_end(); // Close current prompt host_action_prompt_begin(PSTR("Paused")); host_action_prompt_button(PSTR("Purge More")); @@ -133,16 +137,22 @@ void host_action(const char * const pstr, const bool eol) { runout.reset(); } #endif - pause_menu_response = PAUSE_RESPONSE_RESUME_PRINT; + #if ENABLED(ADVANCED_PAUSE_FEATURE) + pause_menu_response = PAUSE_RESPONSE_RESUME_PRINT; + #endif } break; case PROMPT_USER_CONTINUE: + #if HAS_RESUME_CONTINUE + wait_for_user = false; + #endif msg = PSTR("FILAMENT_RUNOUT_CONTINUE"); - wait_for_user = false; break; case PROMPT_PAUSE_RESUME: msg = PSTR("LCD_PAUSE_RESUME"); - queue.inject_P(PSTR("M24")); + #if ENABLED(ADVANCED_PAUSE_FEATURE) + queue.inject_P(PSTR("M24")); + #endif break; case PROMPT_INFO: msg = PSTR("GCODE_INFO"); diff --git a/Marlin/src/feature/leds/leds.cpp b/Marlin/src/feature/leds/leds.cpp index a1e033ab08..e5e952ed6c 100644 --- a/Marlin/src/feature/leds/leds.cpp +++ b/Marlin/src/feature/leds/leds.cpp @@ -39,7 +39,7 @@ #endif #if ENABLED(PCA9533) - #include "SailfishRGB_LED.h" + #include #endif #if ENABLED(LED_COLOR_PRESETS) @@ -69,7 +69,7 @@ void LEDLights::setup() { #endif #endif #if ENABLED(NEOPIXEL_LED) - setup_neopixel(); + neo.init(); #endif #if ENABLED(PCA9533) RGBinit(); @@ -88,23 +88,28 @@ void LEDLights::set_color(const LEDColor &incol #if ENABLED(NEOPIXEL_LED) const uint32_t neocolor = LEDColorWhite() == incol - ? pixels.Color(NEO_WHITE) - : pixels.Color(incol.r, incol.g, incol.b, incol.w); + ? neo.Color(NEO_WHITE) + : neo.Color(incol.r, incol.g, incol.b, incol.w); static uint16_t nextLed = 0; #ifdef NEOPIXEL_BKGD_LED_INDEX - if (NEOPIXEL_BKGD_LED_INDEX == nextLed) { nextLed++; return; } + if (NEOPIXEL_BKGD_LED_INDEX == nextLed) { + if (++nextLed >= neo.pixels()) nextLed = 0; + return; + } #endif - pixels.setBrightness(incol.i); - if (!isSequence) - set_neopixel_color(neocolor); - else { - pixels.setPixelColor(nextLed, neocolor); - pixels.show(); - if (++nextLed >= pixels.numPixels()) nextLed = 0; + + neo.set_brightness(incol.i); + + if (isSequence) { + neo.set_pixel_color(nextLed, neocolor); + neo.show(); + if (++nextLed >= neo.pixels()) nextLed = 0; return; } + neo.set_color(neocolor); + #endif #if ENABLED(BLINKM) diff --git a/Marlin/src/feature/leds/neopixel.cpp b/Marlin/src/feature/leds/neopixel.cpp index d29226c362..a3ceacb42c 100644 --- a/Marlin/src/feature/leds/neopixel.cpp +++ b/Marlin/src/feature/leds/neopixel.cpp @@ -34,73 +34,81 @@ #include "../../core/utility.h" #endif -Adafruit_NeoPixel pixels(NEOPIXEL_PIXELS, NEOPIXEL_PIN, NEOPIXEL_TYPE + NEO_KHZ800); +Marlin_NeoPixel neo; + +Adafruit_NeoPixel Marlin_NeoPixel::adaneo1(NEOPIXEL_PIXELS, NEOPIXEL_PIN, NEOPIXEL_TYPE + NEO_KHZ800) + #if MULTIPLE_NEOPIXEL_TYPES + , Marlin_NeoPixel::adaneo2(NEOPIXEL_PIXELS, NEOPIXEL2_PIN, NEOPIXEL2_TYPE + NEO_KHZ800) + #endif +; #ifdef NEOPIXEL_BKGD_LED_INDEX - void set_neopixel_color_background() { + + void Marlin_NeoPixel::set_color_background() { uint8_t background_color[4] = NEOPIXEL_BKGD_COLOR; - pixels.setPixelColor(NEOPIXEL_BKGD_LED_INDEX, pixels.Color(background_color[0], background_color[1], background_color[2], background_color[3])); + set_pixel_color(NEOPIXEL_BKGD_LED_INDEX, adaneo1.Color(background_color[0], background_color[1], background_color[2], background_color[3])); } + #endif -void set_neopixel_color(const uint32_t color) { - for (uint16_t i = 0; i < pixels.numPixels(); ++i) { +void Marlin_NeoPixel::set_color(const uint32_t color) { + for (uint16_t i = 0; i < pixels(); ++i) { #ifdef NEOPIXEL_BKGD_LED_INDEX if (i == NEOPIXEL_BKGD_LED_INDEX && color != 0x000000) { - set_neopixel_color_background(); + set_color_background(); continue; } #endif - pixels.setPixelColor(i, color); + set_pixel_color(i, color); } - pixels.show(); + show(); } -void set_neopixel_color_startup(const uint32_t color) { - for (uint16_t i = 0; i < pixels.numPixels(); ++i) - pixels.setPixelColor(i, color); - pixels.show(); +void Marlin_NeoPixel::set_color_startup(const uint32_t color) { + for (uint16_t i = 0; i < pixels(); ++i) + set_pixel_color(i, color); + show(); } -void setup_neopixel() { +void Marlin_NeoPixel::init() { SET_OUTPUT(NEOPIXEL_PIN); - pixels.setBrightness(NEOPIXEL_BRIGHTNESS); // 0 - 255 range - pixels.begin(); - pixels.show(); // initialize to all off + set_brightness(NEOPIXEL_BRIGHTNESS); // 0 - 255 range + begin(); + show(); // initialize to all off #if ENABLED(NEOPIXEL_STARTUP_TEST) safe_delay(1000); - set_neopixel_color_startup(pixels.Color(255, 0, 0, 0)); // red + set_color_startup(adaneo1.Color(255, 0, 0, 0)); // red safe_delay(1000); - set_neopixel_color_startup(pixels.Color(0, 255, 0, 0)); // green + set_color_startup(adaneo1.Color(0, 255, 0, 0)); // green safe_delay(1000); - set_neopixel_color_startup(pixels.Color(0, 0, 255, 0)); // blue + set_color_startup(adaneo1.Color(0, 0, 255, 0)); // blue safe_delay(1000); #endif #ifdef NEOPIXEL_BKGD_LED_INDEX - set_neopixel_color_background(); + set_color_background(); #endif #if ENABLED(LED_USER_PRESET_STARTUP) - set_neopixel_color(pixels.Color(LED_USER_PRESET_RED, LED_USER_PRESET_GREEN, LED_USER_PRESET_BLUE, LED_USER_PRESET_WHITE)); + set_color(adaneo1.Color(LED_USER_PRESET_RED, LED_USER_PRESET_GREEN, LED_USER_PRESET_BLUE, LED_USER_PRESET_WHITE)); #else - set_neopixel_color(pixels.Color(0, 0, 0, 0)); + set_color(adaneo1.Color(0, 0, 0, 0)); #endif } #if 0 -bool neopixel_set_led_color(const uint8_t r, const uint8_t g, const uint8_t b, const uint8_t w, const uint8_t p) { - const uint32_t color = pixels.Color(r, g, b, w); - pixels.setBrightness(p); +bool Marlin_NeoPixel::set_led_color(const uint8_t r, const uint8_t g, const uint8_t b, const uint8_t w, const uint8_t p) { + const uint32_t color = adaneo1.Color(r, g, b, w); + set_brightness(p); #if DISABLED(NEOPIXEL_IS_SEQUENTIAL) - set_neopixel_color(color); + set_color(color); return false; #else static uint16_t nextLed = 0; - pixels.setPixelColor(nextLed, color); - pixels.show(); - if (++nextLed >= pixels.numPixels()) nextLed = 0; + set_pixel_color(nextLed, color); + show(); + if (++nextLed >= pixels()) nextLed = 0; return true; #endif } diff --git a/Marlin/src/feature/leds/neopixel.h b/Marlin/src/feature/leds/neopixel.h index 713300b287..b8c8b12ad6 100644 --- a/Marlin/src/feature/leds/neopixel.h +++ b/Marlin/src/feature/leds/neopixel.h @@ -25,11 +25,21 @@ * Neopixel support */ +// ------------------------ +// Includes +// ------------------------ + #include "../../inc/MarlinConfig.h" #include #include +// ------------------------ +// Defines +// ------------------------ + +#define MULTIPLE_NEOPIXEL_TYPES (defined(NEOPIXEL2_TYPE) && (NEOPIXEL2_TYPE != NEOPIXEL_TYPE)) + #define NEOPIXEL_IS_RGB (NEOPIXEL_TYPE == NEO_RGB || NEOPIXEL_TYPE == NEO_RBG || NEOPIXEL_TYPE == NEO_GRB || NEOPIXEL_TYPE == NEO_GBR || NEOPIXEL_TYPE == NEO_BRG || NEOPIXEL_TYPE == NEO_BGR) #define NEOPIXEL_IS_RGBW !NEOPIXEL_IS_RGB @@ -39,8 +49,70 @@ #define NEO_WHITE 0, 0, 0, 255 #endif -void setup_neopixel(); -void set_neopixel_color(const uint32_t color); -//bool neopixel_set_led_color(const uint8_t r, const uint8_t g, const uint8_t b, const uint8_t w, const uint8_t p); +// ------------------------ +// Function prototypes +// ------------------------ -extern Adafruit_NeoPixel pixels; +class Marlin_NeoPixel { +private: + static Adafruit_NeoPixel adaneo1 + #if MULTIPLE_NEOPIXEL_TYPES + , adaneo2 + #endif + ; + +public: + static void init(); + static void set_color_startup(const uint32_t c); + + static void set_color(const uint32_t c); + static void set_color_background(); + //bool set_led_color(const uint8_t r, const uint8_t g, const uint8_t b, const uint8_t w, const uint8_t p); + + #ifdef NEOPIXEL_BKGD_LED_INDEX + static void set_pixel_color(const uint16_t n, const uint32_t c); + #endif + + static inline void begin() { + adaneo1.begin(); + #if MULTIPLE_NEOPIXEL_TYPES + adaneo2.begin(); + #endif + } + + static inline void set_pixel_color(const uint16_t n, const uint32_t c) { + adaneo1.setPixelColor(n, c); + #if MULTIPLE_NEOPIXEL_TYPES + adaneo2.setPixelColor(n, c); + #endif + } + + static inline void set_brightness(const uint8_t b) { + adaneo1.setBrightness(b); + #if MULTIPLE_NEOPIXEL_TYPES + adaneo2.setBrightness(b); + #endif + } + + static inline void show() { + adaneo1.show(); + #if PIN_EXISTS(NEOPIXEL2) + #if MULTIPLE_NEOPIXEL_TYPES + adaneo2.show(); + #else + adaneo1.setPin(NEOPIXEL2_PIN); + adaneo1.show(); + adaneo1.setPin(NEOPIXEL_PIN); + #endif + #endif + } + + // Accessors + static inline uint16_t pixels() { return adaneo1.numPixels(); } + static inline uint8_t brightness() { return adaneo1.getBrightness(); } + static inline uint32_t Color(uint8_t r, uint8_t g, uint8_t b, uint8_t w) { + return adaneo1.Color(r, g, b, w); + } +}; + +extern Marlin_NeoPixel neo; diff --git a/Marlin/src/feature/leds/pca9632.cpp b/Marlin/src/feature/leds/pca9632.cpp index 1f536d6eab..6f69bd31ef 100644 --- a/Marlin/src/feature/leds/pca9632.cpp +++ b/Marlin/src/feature/leds/pca9632.cpp @@ -58,12 +58,21 @@ #define PCA9632_AUTOGLO 0xC0 #define PCA9632_AUTOGI 0xE0 -// Red LED0 -// Green LED1 -// Blue LED2 -#define PCA9632_RED 0x00 -#define PCA9632_GRN 0x02 -#define PCA9632_BLU 0x04 +// Red=LED0 Green=LED1 Blue=LED2 +#ifndef PCA9632_RED + #define PCA9632_RED 0x00 +#endif +#ifndef PCA9632_GRN + #define PCA9632_GRN 0x02 +#endif +#ifndef PCA9632_BLU + #define PCA9632_BLU 0x04 +#endif + +// If any of the color indexes are greater than 0x04 they can't use auto increment +#if !defined(PCA9632_NO_AUTO_INC) && (PCA9632_RED > 0x04 || PCA9632_GRN > 0x04 || PCA9632_BLU > 0x04) + #define PCA9632_NO_AUTO_INC +#endif #define LED_OFF 0x00 #define LED_ON 0x01 @@ -80,12 +89,24 @@ static void PCA9632_WriteRegister(const byte addr, const byte regadd, const byte Wire.endTransmission(); } -static void PCA9632_WriteAllRegisters(const byte addr, const byte regadd, const byte value1, const byte value2, const byte value3) { +static void PCA9632_WriteAllRegisters(const byte addr, const byte regadd, const byte vr, const byte vg, const byte vb) { + #if DISABLED(PCA9632_NO_AUTO_INC) + uint8_t data[4], len = 4; + data[0] = PCA9632_AUTO_IND | regadd; + data[1 + (PCA9632_RED >> 1)] = vr; + data[1 + (PCA9632_GRN >> 1)] = vg; + data[1 + (PCA9632_BLU >> 1)] = vb; + #else + uint8_t data[6], len = 6; + data[0] = regadd + (PCA9632_RED >> 1); + data[1] = vr; + data[2] = regadd + (PCA9632_GRN >> 1); + data[3] = vg; + data[4] = regadd + (PCA9632_BLU >> 1); + data[5] = vb; + #endif Wire.beginTransmission(I2C_ADDRESS(addr)); - Wire.write(PCA9632_AUTO_IND | regadd); - Wire.write(value1); - Wire.write(value2); - Wire.write(value3); + Wire.write(data, len); Wire.endTransmission(); } @@ -115,4 +136,14 @@ void pca9632_set_led_color(const LEDColor &color) { PCA9632_WriteRegister(PCA9632_ADDRESS,PCA9632_LEDOUT, LEDOUT); } +#if ENABLED(PCA9632_BUZZER) + void pca9632_buzz(uint16_t const f, uint16_t d) { + UNUSED(f); UNUSED(d); + uint8_t data[] = PCA9632_BUZZER_DATA; + Wire.beginTransmission(I2C_ADDRESS(PCA9632_ADDRESS)); + Wire.write(data, sizeof(data)); + Wire.endTransmission(); + } +#endif + #endif // PCA9632 diff --git a/Marlin/src/feature/leds/pca9632.h b/Marlin/src/feature/leds/pca9632.h index a231cb9f42..023e451979 100644 --- a/Marlin/src/feature/leds/pca9632.h +++ b/Marlin/src/feature/leds/pca9632.h @@ -30,3 +30,7 @@ struct LEDColor; typedef LEDColor LEDColor; void pca9632_set_led_color(const LEDColor &color); + +#if ENABLED(PCA9632_BUZZER) + void pca9632_buzz(uint16_t const, uint16_t); +#endif diff --git a/Marlin/src/feature/leds/printer_event_leds.cpp b/Marlin/src/feature/leds/printer_event_leds.cpp index 917ec3e64e..3ce7a1af21 100644 --- a/Marlin/src/feature/leds/printer_event_leds.cpp +++ b/Marlin/src/feature/leds/printer_event_leds.cpp @@ -46,7 +46,7 @@ PrinterEventLEDs printerEventLEDs; inline void pel_set_rgb(const uint8_t r, const uint8_t g, const uint8_t b) { leds.set_color( - MakeLEDColor(r, g, b, 0, pixels.getBrightness()) + MakeLEDColor(r, g, b, 0, neo.brightness()) #if ENABLED(NEOPIXEL_IS_SEQUENTIAL) , true #endif diff --git a/Marlin/src/feature/leds/printer_event_leds.h b/Marlin/src/feature/leds/printer_event_leds.h index 4430e5be68..f59d6c699c 100644 --- a/Marlin/src/feature/leds/printer_event_leds.h +++ b/Marlin/src/feature/leds/printer_event_leds.h @@ -36,6 +36,14 @@ private: static bool leds_off_after_print; #endif + static inline void set_done() { + #if ENABLED(LED_COLOR_PRESETS) + leds.set_default(); + #else + leds.set_off(); + #endif + } + public: #if HAS_TEMP_HOTEND static inline LEDColor onHotendHeatingStart() { old_intensity = 0; return leds.get_color(); } @@ -60,14 +68,14 @@ public: leds_off_after_print = true; #else safe_delay(2000); - leds.set_off(); + set_done(); #endif } static inline void onResumeAfterWait() { #if HAS_LEDS_OFF_FLAG if (leds_off_after_print) { - leds.set_off(); + set_done(); leds_off_after_print = false; } #endif diff --git a/Marlin/src/feature/leds/tempstat.cpp b/Marlin/src/feature/leds/tempstat.cpp index acc6bf8a7b..601e433687 100644 --- a/Marlin/src/feature/leds/tempstat.cpp +++ b/Marlin/src/feature/leds/tempstat.cpp @@ -38,10 +38,10 @@ void handle_status_leds(void) { next_status_led_update_ms += 500; // Update every 0.5s float max_temp = 0.0; #if HAS_HEATED_BED - max_temp = MAX(thermalManager.degTargetBed(), thermalManager.degBed()); + max_temp = _MAX(thermalManager.degTargetBed(), thermalManager.degBed()); #endif HOTEND_LOOP() - max_temp = MAX(max_temp, thermalManager.degHotend(e), thermalManager.degTargetHotend(e)); + max_temp = _MAX(max_temp, thermalManager.degHotend(e), thermalManager.degTargetHotend(e)); const int8_t new_red = (max_temp > 55.0) ? HIGH : (max_temp < 54.0 || old_red < 0) ? LOW : old_red; if (new_red != old_red) { old_red = new_red; diff --git a/Marlin/src/feature/mixing.cpp b/Marlin/src/feature/mixing.cpp index db81120a1d..dbdd9558aa 100644 --- a/Marlin/src/feature/mixing.cpp +++ b/Marlin/src/feature/mixing.cpp @@ -136,7 +136,7 @@ void Mixer::refresh_collector(const float proportion/*=1.0*/, const uint8_t t/*= float csum = 0, cmax = 0; MIXER_STEPPER_LOOP(i) { const float v = color[t][i]; - cmax = MAX(cmax, v); + cmax = _MAX(cmax, v); csum += v; } //SERIAL_ECHOPAIR("Mixer::refresh_collector(", proportion, ", ", int(t), ") cmax=", cmax, " csum=", csum, " color"); diff --git a/Marlin/src/feature/mixing.h b/Marlin/src/feature/mixing.h index 5fe149048a..55b54f96c1 100644 --- a/Marlin/src/feature/mixing.h +++ b/Marlin/src/feature/mixing.h @@ -25,7 +25,7 @@ //#define MIXER_NORMALIZER_DEBUG -#if !defined(__AVR__) // || DUAL_MIXING_EXTRUDER +#ifndef __AVR__ // || DUAL_MIXING_EXTRUDER // Use 16-bit (or fastest) data for the integer mix factors typedef uint_fast16_t mixer_comp_t; typedef uint_fast16_t mixer_accu_t; @@ -103,7 +103,7 @@ class Mixer { static void refresh_collector(const float proportion=1.0, const uint8_t t=selected_vtool, float (&c)[MIXING_STEPPERS]=collector); // Used up to Planner level - FORCE_INLINE static void set_collector(const uint8_t c, const float f) { collector[c] = MAX(f, 0.0f); } + FORCE_INLINE static void set_collector(const uint8_t c, const float f) { collector[c] = _MAX(f, 0.0f); } static void normalize(const uint8_t tool_index); FORCE_INLINE static void normalize() { normalize(selected_vtool); } @@ -142,7 +142,7 @@ class Mixer { static inline void copy_mix_to_color(mixer_comp_t (&tcolor)[MIXING_STEPPERS]) { // Scale each component to the largest one in terms of COLOR_A_MASK // So the largest component will be COLOR_A_MASK and the other will be in proportion to it - const float scale = (COLOR_A_MASK) * RECIPROCAL(float(MAX(mix[0], mix[1]))); + const float scale = (COLOR_A_MASK) * RECIPROCAL(float(_MAX(mix[0], mix[1]))); // Scale all values so their maximum is COLOR_A_MASK MIXER_STEPPER_LOOP(i) tcolor[i] = mix[i] * scale; diff --git a/Marlin/src/feature/pause.cpp b/Marlin/src/feature/pause.cpp index 74009c9f30..5700591ca3 100644 --- a/Marlin/src/feature/pause.cpp +++ b/Marlin/src/feature/pause.cpp @@ -54,7 +54,11 @@ #endif #include "../lcd/ultralcd.h" -#include "../libs/buzzer.h" + +#if HAS_BUZZER + #include "../libs/buzzer.h" +#endif + #include "../libs/nozzle.h" #include "pause.h" @@ -436,7 +440,7 @@ bool pause_print(const float &retract, const point_t &park_point, const float &u // Park the nozzle by moving up by z_lift and then moving to (x_pos, y_pos) if (!axis_unhomed_error()) - Nozzle::park(2, park_point); + nozzle.park(2, park_point); #if ENABLED(DUAL_X_CARRIAGE) const int8_t saved_ext = active_extruder; diff --git a/Marlin/src/feature/power_loss_recovery.cpp b/Marlin/src/feature/power_loss_recovery.cpp index ebaa1dfc12..305b79f522 100644 --- a/Marlin/src/feature/power_loss_recovery.cpp +++ b/Marlin/src/feature/power_loss_recovery.cpp @@ -35,6 +35,7 @@ bool PrintJobRecovery::enabled; // Initialized by settings.load() SdFile PrintJobRecovery::file; job_recovery_info_t PrintJobRecovery::info; +const char PrintJobRecovery::filename[5] = "/PLR"; #include "../sd/cardreader.h" #include "../lcd/ultralcd.h" diff --git a/Marlin/src/feature/power_loss_recovery.h b/Marlin/src/feature/power_loss_recovery.h index 57873df265..d58285e563 100644 --- a/Marlin/src/feature/power_loss_recovery.h +++ b/Marlin/src/feature/power_loss_recovery.h @@ -103,6 +103,8 @@ typedef struct { class PrintJobRecovery { public: + static const char filename[5]; + static SdFile file; static job_recovery_info_t info; diff --git a/Marlin/src/feature/prusa_MMU2/mmu2.cpp b/Marlin/src/feature/prusa_MMU2/mmu2.cpp index 8453afc601..3450e98b3f 100644 --- a/Marlin/src/feature/prusa_MMU2/mmu2.cpp +++ b/Marlin/src/feature/prusa_MMU2/mmu2.cpp @@ -573,7 +573,7 @@ void MMU2::manage_response(const bool move_axes, const bool turn_off_nozzle) { COPY(resume_position, current_position); if (move_axes && all_axes_homed()) - Nozzle::park(2, park_point /*= NOZZLE_PARK_POINT*/); + nozzle.park(2, park_point /*= NOZZLE_PARK_POINT*/); if (turn_off_nozzle) thermalManager.setTargetHotend(0, active_extruder); diff --git a/Marlin/src/feature/spindle_laser.h b/Marlin/src/feature/spindle_laser.h index 5d70895ef5..ddc89b5add 100644 --- a/Marlin/src/feature/spindle_laser.h +++ b/Marlin/src/feature/spindle_laser.h @@ -57,12 +57,11 @@ public: //static bool active() { return READ(SPINDLE_LASER_ENA_PIN) == SPINDLE_LASER_ACTIVE_HIGH; } + static void update_output(); + #if ENABLED(SPINDLE_LASER_PWM) - static void update_output(); static void set_ocr(const uint8_t ocr); static inline void set_ocr_power(const uint8_t pwr) { power = pwr; set_ocr(pwr); } - #else - static inline void update_output() { } #endif // Wait for spindle to spin up or spin down diff --git a/Marlin/src/feature/tmc_util.cpp b/Marlin/src/feature/tmc_util.cpp index c432a3cf9a..b3ea6e7cb7 100644 --- a/Marlin/src/feature/tmc_util.cpp +++ b/Marlin/src/feature/tmc_util.cpp @@ -69,7 +69,7 @@ #endif ; #if ENABLED(TMC_DEBUG) - #if HAS_TMCX1X0 || HAS_DRIVER(TMC2208) || HAS_DRIVER(TMC2209) + #if HAS_TMCX1X0 || HAS_TMC220x uint8_t cs_actual; #endif #if HAS_STALLGUARD @@ -139,7 +139,7 @@ #endif // HAS_TMCX1X0 - #if HAS_DRIVER(TMC2208) || HAS_DRIVER(TMC2209) + #if HAS_TMC220x #if ENABLED(TMC_DEBUG) static uint32_t get_pwm_scale(TMC2208Stepper &st) { return st.pwm_scale_sum(); } @@ -239,7 +239,7 @@ st.printLabel(); SERIAL_CHAR(':'); SERIAL_PRINT(pwm_scale, DEC); #if ENABLED(TMC_DEBUG) - #if HAS_TMCX1X0 || HAS_DRIVER(TMC2208) || HAS_DRIVER(TMC2209) + #if HAS_TMCX1X0 || HAS_TMC220x SERIAL_CHAR('/'); SERIAL_PRINT(data.cs_actual, DEC); #endif #if HAS_STALLGUARD @@ -516,7 +516,7 @@ } #endif - #if HAS_DRIVER(TMC2208) || HAS_DRIVER(TMC2209) + #if HAS_TMC220x static void _tmc_status(TMC2208Stepper &st, const TMC_debug_enum i) { switch (i) { case TMC_PWM_SCALE: SERIAL_PRINT(st.pwm_scale_sum(), DEC); break; @@ -787,22 +787,22 @@ #if HAS_DRIVER(TMC2160) || HAS_DRIVER(TMC5160) TMC_REPORT("Global scaler", TMC_GLOBAL_SCALER); #endif - TMC_REPORT("CS actual\t", TMC_CS_ACTUAL); + TMC_REPORT("CS actual", TMC_CS_ACTUAL); TMC_REPORT("PWM scale", TMC_PWM_SCALE); - #if HAS_DRIVER(TMC2130) || HAS_DRIVER(TMC2224) || HAS_DRIVER(TMC2660) || HAS_DRIVER(TMC2208) || HAS_DRIVER(TMC2209) + #if HAS_DRIVER(TMC2130) || HAS_DRIVER(TMC2224) || HAS_DRIVER(TMC2660) || HAS_TMC220x TMC_REPORT("vsense\t", TMC_VSENSE); #endif TMC_REPORT("stealthChop", TMC_STEALTHCHOP); TMC_REPORT("msteps\t", TMC_MICROSTEPS); TMC_REPORT("tstep\t", TMC_TSTEP); - TMC_REPORT("pwm\nthreshold\t", TMC_TPWMTHRS); + TMC_REPORT("pwm\nthreshold", TMC_TPWMTHRS); TMC_REPORT("[mm/s]\t", TMC_TPWMTHRS_MMS); TMC_REPORT("OT prewarn", TMC_OTPW); #if ENABLED(MONITOR_DRIVER_STATUS) TMC_REPORT("OT prewarn has\n" "been triggered", TMC_OTPW_TRIGGERED); #endif - TMC_REPORT("off time\t", TMC_TOFF); + TMC_REPORT("off time", TMC_TOFF); TMC_REPORT("blank time", TMC_TBL); TMC_REPORT("hysteresis\n-end\t", TMC_HEND); TMC_REPORT("-start\t", TMC_HSTRT); @@ -811,7 +811,7 @@ DRV_REPORT("DRVSTATUS", TMC_DRV_CODES); #if HAS_TMCX1X0 DRV_REPORT("stallguard\t", TMC_STALLGUARD); - DRV_REPORT("sg_result\t", TMC_SG_RESULT); + DRV_REPORT("sg_result", TMC_SG_RESULT); DRV_REPORT("fsactive\t", TMC_FSACTIVE); #endif DRV_REPORT("stst\t", TMC_STST); @@ -821,7 +821,7 @@ DRV_REPORT("s2ga\t", TMC_S2GA); DRV_REPORT("otpw\t", TMC_DRV_OTPW); DRV_REPORT("ot\t", TMC_OT); - #if HAS_DRIVER(TMC2208) || HAS_DRIVER(TMC2209) + #if HAS_TMC220x DRV_REPORT("157C\t", TMC_T157); DRV_REPORT("150C\t", TMC_T150); DRV_REPORT("143C\t", TMC_T143); @@ -845,7 +845,7 @@ } } #endif - #if HAS_DRIVER(TMC2208) || HAS_DRIVER(TMC2209) + #if HAS_TMC220x static void tmc_get_ic_registers(TMC2208Stepper, const TMC_get_registers_enum) { SERIAL_CHAR('\t'); } #endif diff --git a/Marlin/src/feature/tmc_util.h b/Marlin/src/feature/tmc_util.h index 1df9a1a3b3..a3eb49a1e0 100644 --- a/Marlin/src/feature/tmc_util.h +++ b/Marlin/src/feature/tmc_util.h @@ -348,17 +348,15 @@ void test_tmc_connection(const bool test_x, const bool test_y, const bool test_z #endif /** - * TMC2130 specific sensorless homing using stallGuard2. + * TMC2130-specific sensorless homing using stallGuard2. * stallGuard2 only works when in spreadCycle mode. - * spreadCycle and stealthChop are mutually exclusive. + * spreadCycle and stealthChop are mutually-exclusive. * * Defined here because of limitations with templates and headers. */ #if USE_SENSORLESS // Track enabled status of stealthChop and only re-enable where applicable - struct sensorless_t { - bool x, y, z, x2, y2, z2, z3; - }; + struct sensorless_t { bool x, y, z, x2, y2, z2, z3; }; bool tmc_enable_stallguard(TMC2130Stepper &st); void tmc_disable_stallguard(TMC2130Stepper &st, const bool restore_stealth); diff --git a/Marlin/src/feature/touch/xpt2046.cpp b/Marlin/src/feature/touch/xpt2046.cpp new file mode 100644 index 0000000000..747659dc7c --- /dev/null +++ b/Marlin/src/feature/touch/xpt2046.cpp @@ -0,0 +1,141 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + +#include "../../inc/MarlinConfigPre.h" + +#if ENABLED(TOUCH_BUTTONS) + +#include "xpt2046.h" +#include "../../inc/MarlinConfig.h" + +#ifndef TOUCH_INT_PIN + #define TOUCH_INT_PIN -1 +#endif +#ifndef TOUCH_MISO_PIN + #define TOUCH_MISO_PIN MISO_PIN +#endif +#ifndef TOUCH_MOSI_PIN + #define TOUCH_MOSI_PIN MOSI_PIN +#endif +#ifndef TOUCH_SCK_PIN + #define TOUCH_SCK_PIN SCK_PIN +#endif +#ifndef TOUCH_CS_PIN + #define TOUCH_CS_PIN CS_PIN +#endif + +XPT2046 touch; +extern int8_t encoderDiff; + +void XPT2046::init(void) { + SET_INPUT(TOUCH_MISO_PIN); + SET_OUTPUT(TOUCH_MOSI_PIN); + SET_OUTPUT(TOUCH_SCK_PIN); + OUT_WRITE(TOUCH_CS_PIN, 1); + + #if PIN_EXISTS(TOUCH_INT) + // Optional Pendrive interrupt pin + SET_INPUT(TOUCH_INT_PIN); + #endif + + // Read once to enable pendrive status pin + getInTouch(XPT2046_X); +} + +#include "../../lcd/ultralcd.h" // For EN_C bit mask + +uint8_t XPT2046::read_buttons() { + int16_t tsoffsets[4] = { 0 }; + + static uint32_t touchtimeout = 0; + if (PENDING(millis(), touchtimeout)) return 0; + touchtimeout = millis() + 80; // ideally want to set this lower for the games... 30 or 40. + + if (tsoffsets[0] + tsoffsets[1] == 0) { + // Not yet set, so use defines as fallback... + tsoffsets[0] = XPT2046_X_CALIBRATION; + tsoffsets[1] = XPT2046_X_OFFSET; + tsoffsets[2] = XPT2046_Y_CALIBRATION; + tsoffsets[3] = XPT2046_Y_OFFSET; + } + + // We rely on XPT2046 compatible mode to ADS7843, hence no Z1 and Z2 measurements possible. + + if (!isTouched()) return 0; + const uint16_t x = uint16_t(((uint32_t(getInTouch(XPT2046_X))) * tsoffsets[0]) >> 16) + tsoffsets[1], + y = uint16_t(((uint32_t(getInTouch(XPT2046_Y))) * tsoffsets[2]) >> 16) + tsoffsets[3]; + if (!isTouched()) return 0; // Fingers must still be on the TS for a valid read. + + if (y < 175 || y > 234) return 0; + + if (WITHIN(x, 11, 109)) encoderDiff = -(ENCODER_STEPS_PER_MENU_ITEM) * ENCODER_PULSES_PER_STEP; + else if (WITHIN(x, 111, 209)) encoderDiff = ENCODER_STEPS_PER_MENU_ITEM * ENCODER_PULSES_PER_STEP; + else if (WITHIN(x, 211, 309)) return EN_C; + return 0; +} + +bool XPT2046::isTouched() { + return ( + #if PIN_EXISTS(TOUCH_INT) + READ(TOUCH_INT_PIN) != HIGH + #else + getInTouch(XPT2046_Z1) >= XPT2046_Z1_THRESHOLD + #endif + ); +} + +uint16_t XPT2046::getInTouch(const XPTCoordinate coordinate) { + uint16_t data[3]; + + OUT_WRITE(TOUCH_CS_PIN, LOW); + + const uint8_t coord = uint8_t(coordinate) | XPT2046_CONTROL | XPT2046_DFR_MODE; + for (uint16_t i = 0; i < 3 ; i++) { + for (uint8_t j = 0x80; j; j >>= 1) { + WRITE(TOUCH_SCK_PIN, LOW); + WRITE(TOUCH_MOSI_PIN, bool(coord & j)); + WRITE(TOUCH_SCK_PIN, HIGH); + } + + data[i] = 0; + for (uint16_t j = 0x8000; j; j >>= 1) { + WRITE(TOUCH_SCK_PIN, LOW); + if (READ(TOUCH_MISO_PIN)) data[i] |= j; + WRITE(TOUCH_SCK_PIN, HIGH); + } + WRITE(TOUCH_SCK_PIN, LOW); + data[i] >>= 4; + } + + WRITE(TOUCH_CS_PIN, HIGH); + + uint16_t delta01 = _MAX(data[0], data[1]) - _MIN(data[0], data[1]), + delta02 = _MAX(data[0], data[2]) - _MIN(data[0], data[2]), + delta12 = _MAX(data[1], data[2]) - _MIN(data[1], data[2]); + + if (delta01 <= delta02 && delta01 <= delta12) + return (data[0] + data[1]) >> 1; + + if (delta02 <= delta12) + return (data[0] + data[2]) >> 1; + + return (data[1] + data[2]) >> 1; +} + +#endif // TOUCH_BUTTONS diff --git a/Marlin/src/feature/touch/xpt2046.h b/Marlin/src/feature/touch/xpt2046.h new file mode 100644 index 0000000000..aea840576c --- /dev/null +++ b/Marlin/src/feature/touch/xpt2046.h @@ -0,0 +1,50 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +#include + +// Relies on XPT2046-compatible mode of ADS7843, +// hence no Z1 / Z2 measurements are possible. + +#define XPT2046_DFR_MODE 0x00 +#define XPT2046_SER_MODE 0x04 +#define XPT2046_CONTROL 0x80 + +enum XPTCoordinate : uint8_t { + XPT2046_X = 0x10, + XPT2046_Y = 0x50, + XPT2046_Z1 = 0x30, + XPT2046_Z2 = 0x40 +}; + +#ifndef XPT2046_Z1_THRESHOLD + #define XPT2046_Z1_THRESHOLD 10 +#endif + +class XPT2046 { +public: + static void init(void); + static uint8_t read_buttons(); +private: + static bool isTouched(); + static uint16_t getInTouch(const XPTCoordinate coordinate); +}; + +extern XPT2046 touch; diff --git a/Marlin/src/gcode/bedlevel/G26.cpp b/Marlin/src/gcode/bedlevel/G26.cpp index 817e5646a6..3b44a29301 100644 --- a/Marlin/src/gcode/bedlevel/G26.cpp +++ b/Marlin/src/gcode/bedlevel/G26.cpp @@ -337,9 +337,9 @@ inline bool look_for_lines_to_connect() { sx = _GET_MESH_X( i ) + (INTERSECTION_CIRCLE_RADIUS - (CROSSHAIRS_SIZE)); // right edge ex = _GET_MESH_X(i + 1) - (INTERSECTION_CIRCLE_RADIUS - (CROSSHAIRS_SIZE)); // left edge - sx = constrain(sx, X_MIN_POS + 1, X_MAX_POS - 1); + LIMIT(sx, X_MIN_POS + 1, X_MAX_POS - 1); sy = ey = constrain(_GET_MESH_Y(j), Y_MIN_POS + 1, Y_MAX_POS - 1); - ex = constrain(ex, X_MIN_POS + 1, X_MAX_POS - 1); + LIMIT(ex, X_MIN_POS + 1, X_MAX_POS - 1); if (position_is_reachable(sx, sy) && position_is_reachable(ex, ey)) print_line_from_here_to_there(sx, sy, g26_layer_height, ex, ey, g26_layer_height); @@ -358,8 +358,8 @@ inline bool look_for_lines_to_connect() { ey = _GET_MESH_Y(j + 1) - (INTERSECTION_CIRCLE_RADIUS - (CROSSHAIRS_SIZE)); // bottom edge sx = ex = constrain(_GET_MESH_X(i), X_MIN_POS + 1, X_MAX_POS - 1); - sy = constrain(sy, Y_MIN_POS + 1, Y_MAX_POS - 1); - ey = constrain(ey, Y_MIN_POS + 1, Y_MAX_POS - 1); + LIMIT(sy, Y_MIN_POS + 1, Y_MAX_POS - 1); + LIMIT(ey, Y_MIN_POS + 1, Y_MAX_POS - 1); if (position_is_reachable(sx, sy) && position_is_reachable(ex, ey)) print_line_from_here_to_there(sx, sy, g26_layer_height, ex, ey, g26_layer_height); @@ -385,7 +385,7 @@ inline bool turn_on_heaters() { #if HAS_HEATED_BED if (g26_bed_temp > 25) { - #if ENABLED(ULTRA_LCD) + #if HAS_SPI_LCD ui.set_status_P(PSTR("G26 Heating Bed."), 99); ui.quick_feedback(); #if HAS_LCD_MENU @@ -406,7 +406,7 @@ inline bool turn_on_heaters() { #endif // HAS_HEATED_BED // Start heating the active nozzle - #if ENABLED(ULTRA_LCD) + #if HAS_SPI_LCD ui.set_status_P(PSTR("G26 Heating Nozzle."), 99); ui.quick_feedback(); #endif @@ -420,7 +420,7 @@ inline bool turn_on_heaters() { ) ) return G26_ERR; - #if ENABLED(ULTRA_LCD) + #if HAS_SPI_LCD ui.reset_status(); ui.quick_feedback(); #endif @@ -472,7 +472,7 @@ inline bool prime_nozzle() { else #endif { - #if ENABLED(ULTRA_LCD) + #if HAS_SPI_LCD ui.set_status_P(PSTR("Fixed Length Prime."), 99); ui.quick_feedback(); #endif @@ -832,10 +832,10 @@ void GcodeSuite::G26() { // Check to make sure this segment is entirely on the bed, skip if not. if (!position_is_reachable(rx, ry) || !position_is_reachable(xe, ye)) continue; #else // not, we need to skip - rx = constrain(rx, X_MIN_POS + 1, X_MAX_POS - 1); // This keeps us from bumping the endstops - ry = constrain(ry, Y_MIN_POS + 1, Y_MAX_POS - 1); - xe = constrain(xe, X_MIN_POS + 1, X_MAX_POS - 1); - ye = constrain(ye, Y_MIN_POS + 1, Y_MAX_POS - 1); + LIMIT(rx, X_MIN_POS + 1, X_MAX_POS - 1); // This keeps us from bumping the endstops + LIMIT(ry, Y_MIN_POS + 1, Y_MAX_POS - 1); + LIMIT(xe, X_MIN_POS + 1, X_MAX_POS - 1); + LIMIT(ye, Y_MIN_POS + 1, Y_MAX_POS - 1); #endif print_line_from_here_to_there(rx, ry, g26_layer_height, xe, ye, g26_layer_height); diff --git a/Marlin/src/gcode/bedlevel/abl/G29.cpp b/Marlin/src/gcode/bedlevel/abl/G29.cpp index 64f5473672..667bf3e9fc 100644 --- a/Marlin/src/gcode/bedlevel/abl/G29.cpp +++ b/Marlin/src/gcode/bedlevel/abl/G29.cpp @@ -36,7 +36,7 @@ #include "../../../module/probe.h" #include "../../queue.h" -#if BOTH(LCD_BED_LEVELING, PROBE_MANUALLY) +#if HAS_DISPLAY #include "../../../lcd/ultralcd.h" #endif @@ -254,8 +254,8 @@ G29_TYPE GcodeSuite::G29() { ABL_VAR int indexIntoAB[GRID_MAX_POINTS_X][GRID_MAX_POINTS_Y]; - ABL_VAR float eqnAMatrix[GRID_MAX_POINTS * 3], // "A" matrix of the linear system of equations - eqnBVector[GRID_MAX_POINTS], // "B" vector of Z points + ABL_VAR float eqnAMatrix[(GRID_MAX_POINTS) * 3], // "A" matrix of the linear system of equations + eqnBVector[GRID_MAX_POINTS], // "B" vector of Z points mean; #endif @@ -311,15 +311,14 @@ G29_TYPE GcodeSuite::G29() { const float rx = RAW_X_POSITION(parser.linearval('X', NAN)), ry = RAW_Y_POSITION(parser.linearval('Y', NAN)); - int8_t i = parser.byteval('I', -1), - j = parser.byteval('J', -1); + int8_t i = parser.byteval('I', -1), j = parser.byteval('J', -1); if (!isnan(rx) && !isnan(ry)) { // Get nearest i / j from rx / ry i = (rx - bilinear_start[X_AXIS] + 0.5 * xGridSpacing) / xGridSpacing; j = (ry - bilinear_start[Y_AXIS] + 0.5 * yGridSpacing) / yGridSpacing; - i = constrain(i, 0, GRID_MAX_POINTS_X - 1); - j = constrain(j, 0, GRID_MAX_POINTS_Y - 1); + LIMIT(i, 0, GRID_MAX_POINTS_X - 1); + LIMIT(j, 0, GRID_MAX_POINTS_Y - 1); } if (WITHIN(i, 0, GRID_MAX_POINTS_X - 1) && WITHIN(j, 0, GRID_MAX_POINTS_Y)) { set_bed_leveling_enabled(false); @@ -394,10 +393,10 @@ G29_TYPE GcodeSuite::G29() { if (parser.seen('H')) { const int16_t size = (int16_t)parser.value_linear_units(); - left_probe_bed_position = MAX(X_CENTER - size / 2, MIN_PROBE_X); - right_probe_bed_position = MIN(left_probe_bed_position + size, MAX_PROBE_X); - front_probe_bed_position = MAX(Y_CENTER - size / 2, MIN_PROBE_Y); - back_probe_bed_position = MIN(front_probe_bed_position + size, MAX_PROBE_Y); + left_probe_bed_position = _MAX(X_CENTER - size / 2, MIN_PROBE_X); + right_probe_bed_position = _MIN(left_probe_bed_position + size, MAX_PROBE_X); + front_probe_bed_position = _MAX(Y_CENTER - size / 2, MIN_PROBE_Y); + back_probe_bed_position = _MIN(front_probe_bed_position + size, MAX_PROBE_Y); } else { left_probe_bed_position = parser.seenval('L') ? (int)RAW_X_POSITION(parser.value_linear_units()) : LEFT_PROBE_BED_POSITION; @@ -511,7 +510,7 @@ G29_TYPE GcodeSuite::G29() { if (verbose_level || seenQ) { SERIAL_ECHOPGM("Manual G29 "); if (g29_in_progress) { - SERIAL_ECHOPAIR("point ", MIN(abl_probe_index + 1, abl_points)); + SERIAL_ECHOPAIR("point ", _MIN(abl_probe_index + 1, abl_points)); SERIAL_ECHOLNPAIR(" of ", abl_points); } else @@ -689,8 +688,11 @@ G29_TYPE GcodeSuite::G29() { zig ^= true; // zag + // An index to print current state + uint8_t pt_index = (PR_OUTER_VAR) * (PR_INNER_END) + 1; + // Inner loop is Y with PROBE_Y_FIRST enabled - for (int8_t PR_INNER_VAR = inStart; PR_INNER_VAR != inStop; PR_INNER_VAR += inInc) { + for (int8_t PR_INNER_VAR = inStart; PR_INNER_VAR != inStop; pt_index++, PR_INNER_VAR += inInc) { const float xBase = left_probe_bed_position + xGridSpacing * xCount, yBase = front_probe_bed_position + yGridSpacing * yCount; @@ -707,11 +709,16 @@ G29_TYPE GcodeSuite::G29() { if (!position_is_reachable_by_probe(xProbe, yProbe)) continue; #endif + if (verbose_level) SERIAL_ECHOLNPAIR("Probing mesh point ", int(pt_index), "/", int(GRID_MAX_POINTS), "."); + #if HAS_DISPLAY + ui.status_printf_P(0, PSTR(MSG_PROBING_MESH " %i/%i"), int(pt_index), int(GRID_MAX_POINTS)); + #endif + measured_z = faux ? 0.001 * random(-100, 101) : probe_pt(xProbe, yProbe, raise_after, verbose_level); if (isnan(measured_z)) { set_bed_leveling_enabled(abl_should_enable); - break; + break; // Breaks out of both loops } #if ENABLED(AUTO_BED_LEVELING_LINEAR) @@ -744,6 +751,11 @@ G29_TYPE GcodeSuite::G29() { // Probe at 3 arbitrary points for (uint8_t i = 0; i < 3; ++i) { + if (verbose_level) SERIAL_ECHOLNPAIR("Probing point ", int(i), "/3."); + #if HAS_DISPLAY + ui.status_printf_P(0, PSTR(MSG_PROBING_MESH " %i/3"), int(i)); + #endif + // Retain the last probe position xProbe = points[i].x; yProbe = points[i].y; @@ -770,6 +782,10 @@ G29_TYPE GcodeSuite::G29() { #endif // AUTO_BED_LEVELING_3POINT + #if HAS_DISPLAY + ui.reset_status(); + #endif + // Stow the probe. No raise for FIX_MOUNTED_PROBE. if (STOW_PROBE()) { set_bed_leveling_enabled(abl_should_enable); @@ -963,12 +979,6 @@ G29_TYPE GcodeSuite::G29() { #endif // ABL_PLANAR - #ifdef Z_PROBE_END_SCRIPT - if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPAIR("Z Probe End Script: ", Z_PROBE_END_SCRIPT); - planner.synchronize(); - process_subcommands_now_P(PSTR(Z_PROBE_END_SCRIPT)); - #endif - // Auto Bed Leveling is complete! Enable if possible. planner.leveling_active = dryrun ? abl_should_enable : true; } // !isnan(measured_z) @@ -985,6 +995,12 @@ G29_TYPE GcodeSuite::G29() { move_z_after_probing(); #endif + #ifdef Z_PROBE_END_SCRIPT + if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPAIR("Z Probe End Script: ", Z_PROBE_END_SCRIPT); + planner.synchronize(); + process_subcommands_now_P(PSTR(Z_PROBE_END_SCRIPT)); + #endif + report_current_position(); G29_RETURN(isnan(measured_z)); diff --git a/Marlin/src/gcode/bedlevel/mbl/G29.cpp b/Marlin/src/gcode/bedlevel/mbl/G29.cpp index 8062019249..b0f6124422 100644 --- a/Marlin/src/gcode/bedlevel/mbl/G29.cpp +++ b/Marlin/src/gcode/bedlevel/mbl/G29.cpp @@ -38,6 +38,10 @@ #include "../../../module/motion.h" #include "../../../module/stepper.h" +#if ENABLED(EXTENSIBLE_UI) + #include "../../../lcd/extensible_ui/ui_api.h" +#endif + // Save 130 bytes with non-duplication of PSTR inline void echo_not_entered(const char c) { SERIAL_CHAR(c); SERIAL_ECHOLNPGM(" not entered."); } @@ -197,7 +201,7 @@ void GcodeSuite::G29() { } // switch(state) if (state == MeshNext) { - SERIAL_ECHOPAIR("MBL G29 point ", MIN(mbl_probe_index, GRID_MAX_POINTS)); + SERIAL_ECHOPAIR("MBL G29 point ", _MIN(mbl_probe_index, GRID_MAX_POINTS)); SERIAL_ECHOLNPAIR(" of ", int(GRID_MAX_POINTS)); } diff --git a/Marlin/src/gcode/calibrate/G28.cpp b/Marlin/src/gcode/calibrate/G28.cpp index cd2c1da70f..039bd3d1a3 100644 --- a/Marlin/src/gcode/calibrate/G28.cpp +++ b/Marlin/src/gcode/calibrate/G28.cpp @@ -75,10 +75,10 @@ const float mlx = max_length(X_AXIS), mly = max_length(Y_AXIS), mlratio = mlx > mly ? mly / mlx : mlx / mly, - fr_mm_s = MIN(homing_feedrate(X_AXIS), homing_feedrate(Y_AXIS)) * SQRT(sq(mlratio) + 1.0); + fr_mm_s = _MIN(homing_feedrate(X_AXIS), homing_feedrate(Y_AXIS)) * SQRT(sq(mlratio) + 1.0); #if ENABLED(SENSORLESS_HOMING) - sensorless_t stealth_states { false, false, false, false, false, false, false }; + sensorless_t stealth_states { false }; stealth_states.x = tmc_enable_stallguard(stepperX); stealth_states.y = tmc_enable_stallguard(stepperY); #if AXIS_HAS_STALLGUARD(X2) @@ -391,15 +391,6 @@ void GcodeSuite::G28(const bool always_home_all) { #endif // DUAL_X_CARRIAGE - #ifdef HOMING_BACKOFF_MM - endstops.enable(false); - constexpr float endstop_backoff[XYZ] = HOMING_BACKOFF_MM; - const float backoff_x = doX ? ABS(endstop_backoff[X_AXIS]) * (X_HOME_DIR) : 0, - backoff_y = doY ? ABS(endstop_backoff[Y_AXIS]) * (Y_HOME_DIR) : 0, - backoff_z = doZ ? ABS(endstop_backoff[Z_AXIS]) * (Z_HOME_DIR) : 0; - if (backoff_z) do_blocking_move_to_z(current_position[Z_AXIS] - backoff_z); - if (backoff_x || backoff_y) do_blocking_move_to_xy(current_position[X_AXIS] - backoff_x, current_position[Y_AXIS] - backoff_y); - #endif endstops.not_homing(); #if BOTH(DELTA, DELTA_HOME_TO_SAFE_ZONE) diff --git a/Marlin/src/gcode/calibrate/G33.cpp b/Marlin/src/gcode/calibrate/G33.cpp index a76900f6c0..397f5d2f75 100644 --- a/Marlin/src/gcode/calibrate/G33.cpp +++ b/Marlin/src/gcode/calibrate/G33.cpp @@ -610,7 +610,7 @@ void GcodeSuite::G33() { } // adjust delta_height and endstops by the max amount - const float z_temp = MAX(delta_endstop_adj[A_AXIS], delta_endstop_adj[B_AXIS], delta_endstop_adj[C_AXIS]); + const float z_temp = _MAX(delta_endstop_adj[A_AXIS], delta_endstop_adj[B_AXIS], delta_endstop_adj[C_AXIS]); delta_height -= z_temp; LOOP_XYZ(axis) delta_endstop_adj[axis] -= z_temp; } diff --git a/Marlin/src/gcode/calibrate/G34_M422.cpp b/Marlin/src/gcode/calibrate/G34_M422.cpp index 44f7845bf6..101b3cc008 100644 --- a/Marlin/src/gcode/calibrate/G34_M422.cpp +++ b/Marlin/src/gcode/calibrate/G34_M422.cpp @@ -123,7 +123,7 @@ void GcodeSuite::G34() { float z_probe = Z_BASIC_CLEARANCE + (G34_MAX_GRADE) * 0.01f * ( #if ENABLED(Z_TRIPLE_STEPPER_DRIVERS) - SQRT(MAX(HYPOT2(z_auto_align_xpos[0] - z_auto_align_ypos[0], z_auto_align_xpos[1] - z_auto_align_ypos[1]), + SQRT(_MAX(HYPOT2(z_auto_align_xpos[0] - z_auto_align_ypos[0], z_auto_align_xpos[1] - z_auto_align_ypos[1]), HYPOT2(z_auto_align_xpos[1] - z_auto_align_ypos[1], z_auto_align_xpos[2] - z_auto_align_ypos[2]), HYPOT2(z_auto_align_xpos[2] - z_auto_align_ypos[2], z_auto_align_xpos[0] - z_auto_align_ypos[0]))) #else @@ -142,6 +142,8 @@ void GcodeSuite::G34() { z_maxdiff = 0.0f, amplification = z_auto_align_amplification; + const ProbePtRaise raise_after = parser.boolval('E') ? PROBE_PT_STOW : PROBE_PT_RAISE; + uint8_t iteration; bool err_break = false; for (iteration = 0; iteration < z_auto_align_iterations; ++iteration) { @@ -159,22 +161,22 @@ void GcodeSuite::G34() { // Safe clearance even on an incline if (iteration == 0 || izstepper > 0) do_blocking_move_to_z(z_probe); - // Probe a Z height for each stepper - if (isnan(probe_pt(z_auto_align_xpos[zstepper], z_auto_align_ypos[zstepper], PROBE_PT_RAISE, 0, true))) { + // Probe a Z height for each stepper. + const float z_probed_height = probe_pt(z_auto_align_xpos[zstepper], z_auto_align_ypos[zstepper], raise_after, 0, true); + if (isnan(z_probed_height)) { SERIAL_ECHOLNPGM("Probing failed."); err_break = true; break; } - // This is not the trigger Z value. It is the position of the probe after raising it. - // It is higher than the trigger value by a constant value (not known here). This value - // is more useful for determining the desired next iteration Z position for probing. It is - // equally well suited for determining the misalignment, just like the trigger position would be. - z_measured[zstepper] = current_position[Z_AXIS]; + // Add height to each value, to provide a more useful target height for + // the next iteration of probing. This allows adjustments to be made away from the bed. + z_measured[zstepper] = z_probed_height + Z_CLEARANCE_BETWEEN_PROBES; + if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPAIR("> Z", int(zstepper + 1), " measured position is ", z_measured[zstepper]); // Remember the minimum measurement to calculate the correction later on - z_measured_min = MIN(z_measured_min, z_measured[zstepper]); + z_measured_min = _MIN(z_measured_min, z_measured[zstepper]); } // for (zstepper) if (err_break) break; @@ -182,11 +184,11 @@ void GcodeSuite::G34() { // Adapt the next probe clearance height based on the new measurements. // Safe_height = lowest distance to bed (= highest measurement) plus highest measured misalignment. #if ENABLED(Z_TRIPLE_STEPPER_DRIVERS) - z_maxdiff = MAX(ABS(z_measured[0] - z_measured[1]), ABS(z_measured[1] - z_measured[2]), ABS(z_measured[2] - z_measured[0])); - z_probe = Z_BASIC_CLEARANCE + MAX(z_measured[0], z_measured[1], z_measured[2]) + z_maxdiff; + z_maxdiff = _MAX(ABS(z_measured[0] - z_measured[1]), ABS(z_measured[1] - z_measured[2]), ABS(z_measured[2] - z_measured[0])); + z_probe = Z_BASIC_CLEARANCE + _MAX(z_measured[0], z_measured[1], z_measured[2]) + z_maxdiff; #else z_maxdiff = ABS(z_measured[0] - z_measured[1]); - z_probe = Z_BASIC_CLEARANCE + MAX(z_measured[0], z_measured[1]) + z_maxdiff; + z_probe = Z_BASIC_CLEARANCE + _MAX(z_measured[0], z_measured[1]) + z_maxdiff; #endif SERIAL_ECHOPAIR("\n" @@ -210,7 +212,7 @@ void GcodeSuite::G34() { z_align_abs = ABS(z_align_move); // Optimize one iterations correction based on the first measurements - if (z_align_abs > 0.0f) amplification = iteration == 1 ? MIN(last_z_align_move[zstepper] / z_align_abs, 2.0f) : z_auto_align_amplification; + if (z_align_abs > 0.0f) amplification = iteration == 1 ? _MIN(last_z_align_move[zstepper] / z_align_abs, 2.0f) : z_auto_align_amplification; // Check for less accuracy compared to last move if (last_z_align_move[zstepper] < z_align_abs - 1.0) { diff --git a/Marlin/src/gcode/calibrate/G425.cpp b/Marlin/src/gcode/calibrate/G425.cpp index 5b3765737b..996b1515b3 100644 --- a/Marlin/src/gcode/calibrate/G425.cpp +++ b/Marlin/src/gcode/calibrate/G425.cpp @@ -74,7 +74,6 @@ struct measurements_t { float nozzle_outer_dimension[2] = {CALIBRATION_NOZZLE_OUTER_DIAMETER, CALIBRATION_NOZZLE_OUTER_DIAMETER}; }; -#define TEMPORARY_BED_LEVELING_STATE(enable) TemporaryBedLevelingState tbls(enable) #define TEMPORARY_SOFT_ENDSTOP_STATE(enable) REMEMBER(tes, soft_endstops_enabled, enable); #if ENABLED(BACKLASH_GCODE) @@ -89,20 +88,6 @@ struct measurements_t { #define TEMPORARY_BACKLASH_SMOOTHING(value) #endif -/** - * A class to save and change the bed leveling state, - * then restore it when it goes out of scope. - */ -class TemporaryBedLevelingState { - bool saved; - - public: - TemporaryBedLevelingState(const bool enable) : saved(planner.leveling_active) { - set_bed_leveling_enabled(enable); - } - ~TemporaryBedLevelingState() { set_bed_leveling_enabled(saved); } -}; - /** * Move to a particular location. Up to three individual axes * and their destinations can be specified, in any order. @@ -120,9 +105,9 @@ inline void move_to( if (a3 != NO_AXIS) destination[a3] = p3; // Make sure coordinates are within bounds - destination[X_AXIS] = MAX(MIN(destination[X_AXIS], X_MAX_POS), X_MIN_POS); - destination[Y_AXIS] = MAX(MIN(destination[Y_AXIS], Y_MAX_POS), Y_MIN_POS); - destination[Z_AXIS] = MAX(MIN(destination[Z_AXIS], Z_MAX_POS), Z_MIN_POS); + destination[X_AXIS] = _MAX(_MIN(destination[X_AXIS], X_MAX_POS), X_MIN_POS); + destination[Y_AXIS] = _MAX(_MIN(destination[Y_AXIS], Y_MAX_POS), Y_MIN_POS); + destination[Z_AXIS] = _MAX(_MIN(destination[Z_AXIS], Z_MAX_POS), Z_MIN_POS); // Move to position do_blocking_move_to(destination, MMM_TO_MMS(CALIBRATION_FEEDRATE_TRAVEL)); diff --git a/Marlin/src/gcode/calibrate/M100.cpp b/Marlin/src/gcode/calibrate/M100.cpp index b6e22b3083..a6f4f8f5d2 100644 --- a/Marlin/src/gcode/calibrate/M100.cpp +++ b/Marlin/src/gcode/calibrate/M100.cpp @@ -75,7 +75,7 @@ char *end_bss = &__bss_end__, *stacklimit = &__StackLimit, - *heaplimit = &__HeapLimit ; + *heaplimit = &__HeapLimit; #define MEMORY_END_CORRECTION 0x200 @@ -94,6 +94,20 @@ #define MEMORY_END_CORRECTION 0x10000 // need to stay well below 0x20080000 or M100 F crashes +#elif defined(__SAMD51__) + + extern unsigned int __bss_end__, __StackLimit, __HeapLimit; + extern "C" void * _sbrk(int incr); + + void *end_bss = &__bss_end__, + *stacklimit = &__StackLimit, + *heaplimit = &__HeapLimit; + + #define MEMORY_END_CORRECTION 0x400 + + char *free_memory_start = (char *)_sbrk(0) + 0x200, // Leave some heap space + *free_memory_end = (char *)stacklimit - MEMORY_END_CORRECTION; + #else #error "M100 - unsupported CPU" #endif diff --git a/Marlin/src/gcode/calibrate/M48.cpp b/Marlin/src/gcode/calibrate/M48.cpp index 6e9ccf1ed8..1746543cf2 100644 --- a/Marlin/src/gcode/calibrate/M48.cpp +++ b/Marlin/src/gcode/calibrate/M48.cpp @@ -30,6 +30,10 @@ #include "../../feature/bedlevel/bedlevel.h" +#if HAS_SPI_LCD + #include "../../lcd/ultralcd.h" +#endif + #if HAS_LEVELING #include "../../module/planner.h" #endif @@ -127,7 +131,7 @@ void GcodeSuite::M48() { (int) (0.1250000000 * (DELTA_PRINTABLE_RADIUS)), (int) (0.3333333333 * (DELTA_PRINTABLE_RADIUS)) #else - (int) 5.0, (int) (0.125 * MIN(X_BED_SIZE, Y_BED_SIZE)) + (int) 5.0, (int) (0.125 * _MIN(X_BED_SIZE, Y_BED_SIZE)) #endif ); @@ -163,8 +167,8 @@ void GcodeSuite::M48() { Y_current = Y_probe_location - (Y_PROBE_OFFSET_FROM_EXTRUDER) + sin(RADIANS(angle)) * radius; #if DISABLED(DELTA) - X_current = constrain(X_current, X_MIN_POS, X_MAX_POS); - Y_current = constrain(Y_current, Y_MIN_POS, Y_MAX_POS); + LIMIT(X_current, X_MIN_POS, X_MAX_POS); + LIMIT(Y_current, Y_MIN_POS, Y_MAX_POS); #else // If we have gone out too far, we can do a simple fix and scale the numbers // back in closer to the origin. @@ -246,6 +250,13 @@ void GcodeSuite::M48() { SERIAL_ECHOLNPAIR_F("Standard Deviation: ", sigma, 6); SERIAL_EOL(); + + #if HAS_SPI_LCD + // Display M48 results in the status bar + char sigma_str[8]; + dtostrf(sigma, 2, 6, sigma_str); + ui.status_printf_P(0, PSTR(MSG_M48_DEVIATION ": %s"), sigma_str); + #endif } clean_up_after_endstop_or_probe_move(); diff --git a/Marlin/src/gcode/config/M200-M205.cpp b/Marlin/src/gcode/config/M200-M205.cpp index 8ae8e58d2e..c43b889244 100644 --- a/Marlin/src/gcode/config/M200-M205.cpp +++ b/Marlin/src/gcode/config/M200-M205.cpp @@ -65,7 +65,7 @@ void GcodeSuite::M201() { planner.settings.max_acceleration_mm_per_s2[a] = parser.value_axis_units((AxisEnum)a); } } - // steps per sq second need to be updated to agree with the units per sq second (as they are what is used in the planner) + planner.reset_acceleration_rates(); } @@ -161,7 +161,7 @@ void GcodeSuite::M205() { SERIAL_ECHOLNPGM("WARNING! Low Z Jerk may lead to unwanted pauses."); #endif } - #if DISABLED(JUNCTION_DEVIATION) || DISABLED(LIN_ADVANCE) + #if !BOTH(JUNCTION_DEVIATION, LIN_ADVANCE) if (parser.seen('E')) planner.max_jerk[E_AXIS] = parser.value_linear_units(); #endif #endif diff --git a/Marlin/src/gcode/config/M217.cpp b/Marlin/src/gcode/config/M217.cpp index e337992ab0..ade8c280f7 100644 --- a/Marlin/src/gcode/config/M217.cpp +++ b/Marlin/src/gcode/config/M217.cpp @@ -32,6 +32,7 @@ void M217_report(const bool eeprom=false) { #if ENABLED(TOOLCHANGE_FILAMENT_SWAP) serialprintPGM(eeprom ? PSTR(" M217") : PSTR("Toolchange:")); SERIAL_ECHOPAIR(" S", LINEAR_UNIT(toolchange_settings.swap_length)); + SERIAL_ECHOPAIR(" E", LINEAR_UNIT(toolchange_settings.extra_prime)); SERIAL_ECHOPAIR(" P", LINEAR_UNIT(toolchange_settings.prime_speed)); SERIAL_ECHOPAIR(" R", LINEAR_UNIT(toolchange_settings.retract_speed)); @@ -54,6 +55,7 @@ void M217_report(const bool eeprom=false) { * M217 - Set SINGLENOZZLE toolchange parameters * * S[linear] Swap length + * E[linear] Purge length * P[linear/m] Prime speed * R[linear/m] Retract speed * X[linear] Park X (Requires TOOLCHANGE_PARK) @@ -68,18 +70,29 @@ void GcodeSuite::M217() { #if ENABLED(TOOLCHANGE_FILAMENT_SWAP) #undef SPR_PARAM - #define SPR_PARAM "SPR" + #define SPR_PARAM "SPRE" - if (parser.seenval('S')) { const float v = parser.value_linear_units(); toolchange_settings.swap_length = constrain(v, 0, 500); } + static constexpr float max_extrude = + #if ENABLED(PREVENT_LENGTHY_EXTRUDE) + EXTRUDE_MAXLENGTH + #else + 500 + #endif + ; + + if (parser.seenval('S')) { const float v = parser.value_linear_units(); toolchange_settings.swap_length = constrain(v, 0, max_extrude); } + if (parser.seenval('E')) { const float v = parser.value_linear_units(); toolchange_settings.extra_prime = constrain(v, 0, max_extrude); } if (parser.seenval('P')) { const int16_t v = parser.value_linear_units(); toolchange_settings.prime_speed = constrain(v, 10, 5400); } if (parser.seenval('R')) { const int16_t v = parser.value_linear_units(); toolchange_settings.retract_speed = constrain(v, 10, 5400); } #endif + #if ENABLED(TOOLCHANGE_PARK) #undef XY_PARAM #define XY_PARAM "XY" if (parser.seenval('X')) { toolchange_settings.change_point.x = parser.value_linear_units(); } if (parser.seenval('Y')) { toolchange_settings.change_point.y = parser.value_linear_units(); } #endif + if (parser.seenval('Z')) { toolchange_settings.z_raise = parser.value_linear_units(); } if (!parser.seen(SPR_PARAM XY_PARAM "Z")) M217_report(); diff --git a/Marlin/src/gcode/config/M43.cpp b/Marlin/src/gcode/config/M43.cpp index 79428158e0..8909397b32 100644 --- a/Marlin/src/gcode/config/M43.cpp +++ b/Marlin/src/gcode/config/M43.cpp @@ -42,6 +42,10 @@ #include "../../feature/host_actions.h" #endif +#ifndef GET_PIN_MAP_PIN_M43 + #define GET_PIN_MAP_PIN_M43(Q) GET_PIN_MAP_PIN(Q) +#endif + inline void toggle_pins() { const bool ignore_protection = parser.boolval('I'); const int repeat = parser.intval('R', 1), @@ -50,7 +54,7 @@ inline void toggle_pins() { wait = parser.intval('W', 500); for (uint8_t i = start; i <= end; i++) { - pin_t pin = GET_PIN_MAP_PIN(i); + pin_t pin = GET_PIN_MAP_PIN_M43(i); if (!VALID_PIN(pin)) continue; if (M43_NEVER_TOUCH(i) || (!ignore_protection && pin_is_protected(pin))) { report_pin_state_extended(pin, ignore_protection, true, "Untouched "); @@ -306,7 +310,7 @@ void GcodeSuite::M43() { #endif uint8_t pin_state[last_pin - first_pin + 1]; for (uint8_t i = first_pin; i <= last_pin; i++) { - pin_t pin = GET_PIN_MAP_PIN(i); + pin_t pin = GET_PIN_MAP_PIN_M43(i); if (!VALID_PIN(pin)) continue; if (M43_NEVER_TOUCH(i) || (!ignore_protection && pin_is_protected(pin))) continue; pinMode(pin, INPUT_PULLUP); @@ -329,7 +333,7 @@ void GcodeSuite::M43() { for (;;) { for (uint8_t i = first_pin; i <= last_pin; i++) { - pin_t pin = GET_PIN_MAP_PIN(i); + pin_t pin = GET_PIN_MAP_PIN_M43(i); if (!VALID_PIN(pin)) continue; if (M43_NEVER_TOUCH(i) || (!ignore_protection && pin_is_protected(pin))) continue; const byte val = @@ -355,7 +359,7 @@ void GcodeSuite::M43() { else { // Report current state of selected pin(s) for (uint8_t i = first_pin; i <= last_pin; i++) { - pin_t pin = GET_PIN_MAP_PIN(i); + pin_t pin = GET_PIN_MAP_PIN_M43(i); if (VALID_PIN(pin)) report_pin_state_extended(pin, ignore_protection, true); } } diff --git a/Marlin/src/gcode/config/M575.cpp b/Marlin/src/gcode/config/M575.cpp new file mode 100644 index 0000000000..a90129f470 --- /dev/null +++ b/Marlin/src/gcode/config/M575.cpp @@ -0,0 +1,74 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + +#include "../../inc/MarlinConfig.h" + +#if ENABLED(BAUD_RATE_GCODE) + +#include "../gcode.h" + +/** + * M575 - Change serial baud rate + * + * P - Serial port index. Omit for all. + * B - Baud rate (bits per second) + */ +void GcodeSuite::M575() { + const int32_t baud = parser.ulongval('B'); + switch (baud) { + case 2400: case 9600: case 19200: case 38400: case 57600: + case 115200: case 250000: case 500000: case 1000000: { + const int8_t port = parser.intval('P', -99); + const bool set0 = (port == -99 || port == 0); + if (set0) { + SERIAL_ECHO_START(); + SERIAL_ECHOLNPAIR(" Serial " + #if NUM_SERIAL > 1 + , '0', + #else + "0" + #endif + " baud rate set to ", baud + ); + } + #if NUM_SERIAL > 1 + const bool set1 = (port == -99 || port == 1); + if (set1) { + SERIAL_ECHO_START(); + SERIAL_ECHOLNPAIR(" Serial ", '1', " baud rate set to ", baud); + } + #endif + + SERIAL_FLUSH(); + + if (set0) { MYSERIAL0.end(); MYSERIAL0.begin(baud); } + + #if NUM_SERIAL > 1 + if (set1) { MYSERIAL1.end(); MYSERIAL1.begin(baud); } + #endif + + } break; + default: SERIAL_ECHO_MSG("?(B)aud rate is implausible."); + } +} + +#endif // NUM_SERIAL > 0 && BAUD_RATE_GCODE diff --git a/Marlin/src/gcode/config/M92.cpp b/Marlin/src/gcode/config/M92.cpp index dc4b134af7..3965136e6b 100644 --- a/Marlin/src/gcode/config/M92.cpp +++ b/Marlin/src/gcode/config/M92.cpp @@ -76,7 +76,7 @@ void GcodeSuite::M92() { const float value = parser.value_per_axis_units((AxisEnum)(E_AXIS_N(target_extruder))); if (value < 20) { float factor = planner.settings.axis_steps_per_mm[E_AXIS_N(target_extruder)] / value; // increase e constants if M92 E14 is given for netfab. - #if HAS_CLASSIC_JERK && (DISABLED(JUNCTION_DEVIATION) || DISABLED(LIN_ADVANCE)) + #if HAS_CLASSIC_JERK && !BOTH(JUNCTION_DEVIATION, LIN_ADVANCE) planner.max_jerk[E_AXIS] *= factor; #endif planner.settings.max_feedrate_mm_s[E_AXIS_N(target_extruder)] *= factor; diff --git a/Marlin/src/gcode/control/M605.cpp b/Marlin/src/gcode/control/M605.cpp index 97e3406cfa..4009a23706 100644 --- a/Marlin/src/gcode/control/M605.cpp +++ b/Marlin/src/gcode/control/M605.cpp @@ -92,7 +92,7 @@ case DXC_AUTO_PARK_MODE: break; case DXC_DUPLICATION_MODE: - if (parser.seen('X')) duplicate_extruder_x_offset = MAX(parser.value_linear_units(), X2_MIN_POS - x_home_pos(0)); + if (parser.seen('X')) duplicate_extruder_x_offset = _MAX(parser.value_linear_units(), X2_MIN_POS - x_home_pos(0)); if (parser.seen('R')) duplicate_extruder_temp_offset = parser.value_celsius_diff(); if (active_extruder != 0) tool_change(0); break; diff --git a/Marlin/src/gcode/feature/advance/M900.cpp b/Marlin/src/gcode/feature/advance/M900.cpp index 251051d312..a5c0dc5cd7 100644 --- a/Marlin/src/gcode/feature/advance/M900.cpp +++ b/Marlin/src/gcode/feature/advance/M900.cpp @@ -44,10 +44,10 @@ void GcodeSuite::M900() { #if EXTRUDERS < 2 - constexpr uint8_t tmp_extruder = 0; + constexpr uint8_t tool_index = 0; #else - const uint8_t tmp_extruder = parser.intval('T', active_extruder); - if (tmp_extruder >= EXTRUDERS) { + const uint8_t tool_index = parser.intval('T', active_extruder); + if (tool_index >= EXTRUDERS) { SERIAL_ECHOLNPGM("?T value out of range."); return; } @@ -55,17 +55,17 @@ void GcodeSuite::M900() { #if ENABLED(EXTRA_LIN_ADVANCE_K) - bool ext_slot = TEST(lin_adv_slot, tmp_extruder); + bool ext_slot = TEST(lin_adv_slot, tool_index); if (parser.seenval('S')) { const bool slot = parser.value_bool(); if (ext_slot != slot) { ext_slot = slot; - SET_BIT_TO(lin_adv_slot, tmp_extruder, slot); + SET_BIT_TO(lin_adv_slot, tool_index, slot); planner.synchronize(); - const float temp = planner.extruder_advance_K[tmp_extruder]; - planner.extruder_advance_K[tmp_extruder] = saved_extruder_advance_K[tmp_extruder]; - saved_extruder_advance_K[tmp_extruder] = temp; + const float temp = planner.extruder_advance_K[tool_index]; + planner.extruder_advance_K[tool_index] = saved_extruder_advance_K[tool_index]; + saved_extruder_advance_K[tool_index] = temp; } } @@ -73,10 +73,10 @@ void GcodeSuite::M900() { const float newK = parser.value_float(); if (WITHIN(newK, 0, 10)) { if (ext_slot) - saved_extruder_advance_K[tmp_extruder] = newK; + saved_extruder_advance_K[tool_index] = newK; else { planner.synchronize(); - planner.extruder_advance_K[tmp_extruder] = newK; + planner.extruder_advance_K[tool_index] = newK; } } else @@ -87,10 +87,10 @@ void GcodeSuite::M900() { const float newL = parser.value_float(); if (WITHIN(newL, 0, 10)) { if (!ext_slot) - saved_extruder_advance_K[tmp_extruder] = newL; + saved_extruder_advance_K[tool_index] = newL; else { planner.synchronize(); - planner.extruder_advance_K[tmp_extruder] = newL; + planner.extruder_advance_K[tool_index] = newL; } } else @@ -117,7 +117,7 @@ void GcodeSuite::M900() { const float newK = parser.value_float(); if (WITHIN(newK, 0, 10)) { planner.synchronize(); - planner.extruder_advance_K[tmp_extruder] = newK; + planner.extruder_advance_K[tool_index] = newK; } else SERIAL_ECHOLNPGM("?K value out of range (0-10)."); diff --git a/Marlin/src/gcode/feature/clean/G12.cpp b/Marlin/src/gcode/feature/clean/G12.cpp index d0aa0c16ed..30c71264eb 100644 --- a/Marlin/src/gcode/feature/clean/G12.cpp +++ b/Marlin/src/gcode/feature/clean/G12.cpp @@ -47,17 +47,20 @@ void GcodeSuite::G12() { objects = parser.ushortval('T', NOZZLE_CLEAN_TRIANGLES); const float radius = parser.floatval('R', NOZZLE_CLEAN_CIRCLE_RADIUS); + const bool seenxyz = parser.seen("XYZ"); + const uint8_t cleans = (!seenxyz || parser.boolval('X') ? _BV(X_AXIS) : 0) + | (!seenxyz || parser.boolval('Y') ? _BV(Y_AXIS) : 0) + #if DISABLED(NOZZLE_CLEAN_NO_Z) + | (!seenxyz || parser.boolval('Z') ? _BV(Z_AXIS) : 0) + #endif + ; + #if HAS_LEVELING - const bool was_enabled = planner.leveling_active; - set_bed_leveling_enabled(false); + // Disable bed leveling if cleaning Z + TEMPORARY_BED_LEVELING_STATE(!TEST(cleans, Z_AXIS) && planner.leveling_active); #endif - Nozzle::clean(pattern, strokes, radius, objects); - - // Re-enable bed level correction if it had been on - #if HAS_LEVELING - set_bed_leveling_enabled(was_enabled); - #endif + nozzle.clean(pattern, strokes, radius, objects, cleans); } #endif // NOZZLE_CLEAN_FEATURE diff --git a/Marlin/src/gcode/feature/leds/M150.cpp b/Marlin/src/gcode/feature/leds/M150.cpp index 1e98ffca2a..405be898ae 100644 --- a/Marlin/src/gcode/feature/leds/M150.cpp +++ b/Marlin/src/gcode/feature/leds/M150.cpp @@ -50,7 +50,7 @@ void GcodeSuite::M150() { parser.seen('U') ? (parser.has_value() ? parser.value_byte() : 255) : 0, parser.seen('B') ? (parser.has_value() ? parser.value_byte() : 255) : 0, parser.seen('W') ? (parser.has_value() ? parser.value_byte() : 255) : 0, - parser.seen('P') ? (parser.has_value() ? parser.value_byte() : 255) : pixels.getBrightness() + parser.seen('P') ? (parser.has_value() ? parser.value_byte() : 255) : neo.brightness() )); } diff --git a/Marlin/src/gcode/feature/leds/M7219.cpp b/Marlin/src/gcode/feature/leds/M7219.cpp index aa8d063a6e..c8257f6581 100644 --- a/Marlin/src/gcode/feature/leds/M7219.cpp +++ b/Marlin/src/gcode/feature/leds/M7219.cpp @@ -33,13 +33,16 @@ * I - Initialize (clear) the matrix * F - Fill the matrix (set all bits) * P - Dump the led_line[] array values - * C - Set a column to the 8-bit value V - * R - Set a row to the 8-bit value V - * X - X position of an LED to set or toggle - * Y - Y position of an LED to set or toggle - * V - The potentially 32-bit value or on/off state to set - * (for example: a chain of 4 Max7219 devices can have 32 bit - * rows or columns depending upon rotation) + * C - Set a column to the bitmask given by 'V' (Units 0-3 in portrait layout) + * R - Set a row to the bitmask given by 'V' (Units 0-3 in landscape layout) + * X - X index of an LED to set or toggle + * Y - Y index of an LED to set or toggle + * V - LED on/off state or row/column bitmask (8, 16, 24, or 32-bits) + * ('C' / 'R' can be used to update up to 4 units at once) + * + * Directly set a native matrix row to the 8-bit value 'V': + * D - Display line (0..7) + * U - Unit index (0..MAX7219_NUMBER_UNITS-1) */ void GcodeSuite::M7219() { if (parser.seen('I')) { @@ -62,12 +65,13 @@ void GcodeSuite::M7219() { else if (parser.seenval('X') || parser.seenval('Y')) { const uint8_t x = parser.byteval('X'), y = parser.byteval('Y'); if (parser.seenval('V')) - max7219.led_set(x, y, parser.boolval('V')); + max7219.led_set(x, y, v > 0); else max7219.led_toggle(x, y); } else if (parser.seen('D')) { - const uint8_t line = parser.byteval('D') + (parser.byteval('U') << 3); + const uint8_t uline = parser.value_byte() & 0x7, + line = uline + parser.byteval('U') << 3; if (line < MAX7219_LINES) { max7219.led_line[line] = v; return max7219.refresh_line(line); diff --git a/Marlin/src/gcode/feature/pause/G27.cpp b/Marlin/src/gcode/feature/pause/G27.cpp index 3b49ae283e..4f4c9e4698 100644 --- a/Marlin/src/gcode/feature/pause/G27.cpp +++ b/Marlin/src/gcode/feature/pause/G27.cpp @@ -35,7 +35,7 @@ void GcodeSuite::G27() { // Don't allow nozzle parking without homing first if (axis_unhomed_error()) return; - Nozzle::park(parser.ushortval('P')); + nozzle.park(parser.ushortval('P')); } #endif // NOZZLE_PARK_FEATURE diff --git a/Marlin/src/gcode/feature/pause/M125.cpp b/Marlin/src/gcode/feature/pause/M125.cpp index 06551242b7..86e8f61c1c 100644 --- a/Marlin/src/gcode/feature/pause/M125.cpp +++ b/Marlin/src/gcode/feature/pause/M125.cpp @@ -67,7 +67,7 @@ void GcodeSuite::M125() { // Lift Z axis if (parser.seenval('Z')) park_point.z = parser.linearval('Z'); - #if HAS_HOTEND_OFFSET && DISABLED(DUAL_X_CARRIAGE, DELTA) + #if HAS_HOTEND_OFFSET && NONE(DUAL_X_CARRIAGE, DELTA) park_point.x += hotend_offset[X_AXIS][active_extruder]; park_point.y += hotend_offset[Y_AXIS][active_extruder]; #endif diff --git a/Marlin/src/gcode/feature/pause/M600.cpp b/Marlin/src/gcode/feature/pause/M600.cpp index 5daf9f57a9..6cadbe6080 100644 --- a/Marlin/src/gcode/feature/pause/M600.cpp +++ b/Marlin/src/gcode/feature/pause/M600.cpp @@ -126,7 +126,7 @@ void GcodeSuite::M600() { if (parser.seenval('X')) park_point.x = parser.linearval('X'); if (parser.seenval('Y')) park_point.y = parser.linearval('Y'); - #if HAS_HOTEND_OFFSET && DISABLED(DUAL_X_CARRIAGE, DELTA) + #if HAS_HOTEND_OFFSET && NONE(DUAL_X_CARRIAGE, DELTA) park_point.x += hotend_offset[X_AXIS][active_extruder]; park_point.y += hotend_offset[Y_AXIS][active_extruder]; #endif diff --git a/Marlin/src/gcode/feature/pause/M701_M702.cpp b/Marlin/src/gcode/feature/pause/M701_M702.cpp index cf22d892d2..b127a9fbad 100644 --- a/Marlin/src/gcode/feature/pause/M701_M702.cpp +++ b/Marlin/src/gcode/feature/pause/M701_M702.cpp @@ -97,7 +97,7 @@ void GcodeSuite::M701() { // Lift Z axis if (park_point.z > 0) - do_blocking_move_to_z(MIN(current_position[Z_AXIS] + park_point.z, Z_MAX_POS), NOZZLE_PARK_Z_FEEDRATE); + do_blocking_move_to_z(_MIN(current_position[Z_AXIS] + park_point.z, Z_MAX_POS), NOZZLE_PARK_Z_FEEDRATE); // Load filament #if ENABLED(PRUSA_MMU2) @@ -116,7 +116,7 @@ void GcodeSuite::M701() { // Restore Z axis if (park_point.z > 0) - do_blocking_move_to_z(MAX(current_position[Z_AXIS] - park_point.z, 0), NOZZLE_PARK_Z_FEEDRATE); + do_blocking_move_to_z(_MAX(current_position[Z_AXIS] - park_point.z, 0), NOZZLE_PARK_Z_FEEDRATE); #if EXTRUDERS > 1 && DISABLED(PRUSA_MMU2) // Restore toolhead if it was changed @@ -196,7 +196,7 @@ void GcodeSuite::M702() { // Lift Z axis if (park_point.z > 0) - do_blocking_move_to_z(MIN(current_position[Z_AXIS] + park_point.z, Z_MAX_POS), NOZZLE_PARK_Z_FEEDRATE); + do_blocking_move_to_z(_MIN(current_position[Z_AXIS] + park_point.z, Z_MAX_POS), NOZZLE_PARK_Z_FEEDRATE); // Unload filament #if ENABLED(PRUSA_MMU2) @@ -226,7 +226,7 @@ void GcodeSuite::M702() { // Restore Z axis if (park_point.z > 0) - do_blocking_move_to_z(MAX(current_position[Z_AXIS] - park_point.z, 0), NOZZLE_PARK_Z_FEEDRATE); + do_blocking_move_to_z(_MAX(current_position[Z_AXIS] - park_point.z, 0), NOZZLE_PARK_Z_FEEDRATE); #if EXTRUDERS > 1 && DISABLED(PRUSA_MMU2) // Restore toolhead if it was changed diff --git a/Marlin/src/gcode/feature/runout/M412.cpp b/Marlin/src/gcode/feature/runout/M412.cpp index 5064b6f5b0..7a5dd65e0e 100644 --- a/Marlin/src/gcode/feature/runout/M412.cpp +++ b/Marlin/src/gcode/feature/runout/M412.cpp @@ -31,12 +31,12 @@ * M412: Enable / Disable filament runout detection */ void GcodeSuite::M412() { - if (parser.seen("HS" + if (parser.seen("RS" #ifdef FILAMENT_RUNOUT_DISTANCE_MM "D" #endif #if ENABLED(HOST_ACTION_COMMANDS) - "R" + "H" #endif )) { #if ENABLED(HOST_ACTION_COMMANDS) diff --git a/Marlin/src/gcode/feature/trinamic/M122.cpp b/Marlin/src/gcode/feature/trinamic/M122.cpp index b4b66ddbc8..bbbe86bdb8 100644 --- a/Marlin/src/gcode/feature/trinamic/M122.cpp +++ b/Marlin/src/gcode/feature/trinamic/M122.cpp @@ -41,7 +41,7 @@ void GcodeSuite::M122() { #if ENABLED(MONITOR_DRIVER_STATUS) const bool sflag = parser.seen('S'), s0 = sflag && !parser.value_bool(); if (sflag) tmc_set_report_interval(s0 ? 0 : MONITOR_DRIVER_STATUS_INTERVAL_MS); - if (!s0 && parser.seenval('P')) tmc_set_report_interval(MIN(parser.value_ushort(), MONITOR_DRIVER_STATUS_INTERVAL_MS)); + if (!s0 && parser.seenval('P')) tmc_set_report_interval(_MIN(parser.value_ushort(), MONITOR_DRIVER_STATUS_INTERVAL_MS)); #endif if (parser.seen('V')) diff --git a/Marlin/src/gcode/gcode.cpp b/Marlin/src/gcode/gcode.cpp index ec76671f1c..cbad59eac6 100644 --- a/Marlin/src/gcode/gcode.cpp +++ b/Marlin/src/gcode/gcode.cpp @@ -669,6 +669,10 @@ void GcodeSuite::process_parsed_command(const bool no_ok/*=false*/) { case 540: M540(); break; // M540: Set abort on endstop hit for SD printing #endif + #if ENABLED(BAUD_RATE_GCODE) + case 575: M575(); break; // M575: Set serial baudrate + #endif + #if HAS_BED_PROBE case 851: M851(); break; // M851: Set Z Probe Z Offset #endif diff --git a/Marlin/src/gcode/gcode.h b/Marlin/src/gcode/gcode.h index 93b91e3eec..9a90c5df4d 100644 --- a/Marlin/src/gcode/gcode.h +++ b/Marlin/src/gcode/gcode.h @@ -274,7 +274,6 @@ * T0-T3 - Select an extruder (tool) by index: "T F" * */ -#pragma once #include "../inc/MarlinConfig.h" #include "parser.h" @@ -782,6 +781,10 @@ private: static void M540(); #endif + #if ENABLED(BAUD_RATE_GCODE) + static void M575(); + #endif + #if ENABLED(ADVANCED_PAUSE_FEATURE) static void M600(); static void M603(); diff --git a/Marlin/src/gcode/lcd/M117.cpp b/Marlin/src/gcode/lcd/M117.cpp index 19cbbc2580..118b55fe37 100644 --- a/Marlin/src/gcode/lcd/M117.cpp +++ b/Marlin/src/gcode/lcd/M117.cpp @@ -28,6 +28,9 @@ */ void GcodeSuite::M117() { - ui.set_status(parser.string_arg); + if (parser.string_arg && parser.string_arg[0]) + ui.set_status(parser.string_arg); + else + ui.reset_status(); } diff --git a/Marlin/src/gcode/lcd/M73.cpp b/Marlin/src/gcode/lcd/M73.cpp index 4ed7559835..85fb7831ea 100644 --- a/Marlin/src/gcode/lcd/M73.cpp +++ b/Marlin/src/gcode/lcd/M73.cpp @@ -22,7 +22,7 @@ #include "../../inc/MarlinConfig.h" -#if ENABLED(LCD_SET_PROGRESS_MANUALLY) && EITHER(EXTENSIBLE_UI, ULTRA_LCD) +#if ENABLED(LCD_SET_PROGRESS_MANUALLY) #include "../gcode.h" #include "../../lcd/ultralcd.h" @@ -42,4 +42,4 @@ void GcodeSuite::M73() { ui.set_progress(parser.value_byte()); } -#endif // LCD_SET_PROGRESS_MANUALLY && (EXTENSIBLE_UI || ULTRA_LCD) +#endif // LCD_SET_PROGRESS_MANUALLY diff --git a/Marlin/src/gcode/queue.cpp b/Marlin/src/gcode/queue.cpp index d519378a29..08cc26eb94 100644 --- a/Marlin/src/gcode/queue.cpp +++ b/Marlin/src/gcode/queue.cpp @@ -170,16 +170,19 @@ bool GCodeQueue::process_injected_command() { char c; size_t i = 0; while ((c = pgm_read_byte(&injected_commands_P[i])) && c != '\n') i++; - if (i) { - char cmd[i + 1]; - memcpy_P(cmd, injected_commands_P, i); - cmd[i] = '\0'; + // Extract current command and move pointer to next command + char cmd[i + 1]; + memcpy_P(cmd, injected_commands_P, i); + cmd[i] = '\0'; + injected_commands_P = c ? injected_commands_P + i + 1 : nullptr; + + // Execute command if non-blank + if (i) { parser.parse(cmd); PORT_REDIRECT(SERIAL_PORT); gcode.process_parsed_command(); } - injected_commands_P = c ? injected_commands_P + i + 1 : nullptr; return true; } diff --git a/Marlin/src/gcode/sdcard/M23.cpp b/Marlin/src/gcode/sdcard/M23.cpp index 87aa213ddc..f170345c57 100644 --- a/Marlin/src/gcode/sdcard/M23.cpp +++ b/Marlin/src/gcode/sdcard/M23.cpp @@ -26,6 +26,7 @@ #include "../gcode.h" #include "../../sd/cardreader.h" +#include "../../lcd/ultralcd.h" /** * M23: Open a file @@ -36,6 +37,10 @@ void GcodeSuite::M23() { // Simplify3D includes the size, so zero out all spaces (#7227) for (char *fn = parser.string_arg; *fn; ++fn) if (*fn == ' ') *fn = '\0'; card.openFile(parser.string_arg, true); + + #if ENABLED(LCD_SET_PROGRESS_MANUALLY) + ui.set_progress(0); + #endif } #endif // SDSUPPORT diff --git a/Marlin/src/gcode/temperature/M104_M109.cpp b/Marlin/src/gcode/temperature/M104_M109.cpp index b17243851d..f4259abff9 100644 --- a/Marlin/src/gcode/temperature/M104_M109.cpp +++ b/Marlin/src/gcode/temperature/M104_M109.cpp @@ -125,7 +125,7 @@ void GcodeSuite::M109() { print_job_timer.start(); #endif - #if EITHER(ULTRA_LCD, EXTENSIBLE_UI) + #if HAS_DISPLAY if (thermalManager.isHeatingHotend(target_extruder) || !no_wait_for_cooling) thermalManager.set_heating_message(target_extruder); #endif diff --git a/Marlin/src/gcode/temperature/M106_M107.cpp b/Marlin/src/gcode/temperature/M106_M107.cpp index b8ff02226a..ede826a3f1 100644 --- a/Marlin/src/gcode/temperature/M106_M107.cpp +++ b/Marlin/src/gcode/temperature/M106_M107.cpp @@ -32,7 +32,7 @@ #define _ALT_P active_extruder #define _CNT_P EXTRUDERS #else - #define _ALT_P MIN(active_extruder, FAN_COUNT - 1) + #define _ALT_P _MIN(active_extruder, FAN_COUNT - 1) #define _CNT_P FAN_COUNT #endif diff --git a/Marlin/src/inc/Conditionals_LCD.h b/Marlin/src/inc/Conditionals_LCD.h index b55c658024..da099fffaf 100644 --- a/Marlin/src/inc/Conditionals_LCD.h +++ b/Marlin/src/inc/Conditionals_LCD.h @@ -29,22 +29,18 @@ #if ENABLED(CARTESIO_UI) #define DOGLCD - #define ULTIPANEL + #define IS_ULTIPANEL #define DEFAULT_LCD_CONTRAST 90 #define LCD_CONTRAST_MIN 60 #define LCD_CONTRAST_MAX 140 -#elif ENABLED(MAKRPANEL) - - #define U8GLIB_ST7565_64128N - #elif ENABLED(ZONESTAR_LCD) #define ADC_KEYPAD - #define REPRAPWORLD_KEYPAD + #define IS_RRW_KEYPAD #define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 #define ADC_KEY_NUM 8 - #define ULTIPANEL + #define IS_ULTIPANEL // This helps to implement ADC_KEYPAD menus #define REVERSE_MENU_DIRECTION @@ -53,22 +49,18 @@ #define ENCODER_FEEDRATE_DEADZONE 2 #elif ENABLED(RADDS_DISPLAY) - #define ULTIPANEL + #define IS_ULTIPANEL #define ENCODER_PULSES_PER_STEP 2 -#elif ENABLED(ANET_FULL_GRAPHICS_LCD) +#elif EITHER(ANET_FULL_GRAPHICS_LCD, BQ_LCD_SMART_CONTROLLER) - #define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER - -#elif ENABLED(BQ_LCD_SMART_CONTROLLER) - - #define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER + #define IS_RRD_FG_SC #elif ANY(miniVIKI, VIKI2, ELB_FULL_GRAPHIC_CONTROLLER, AZSMZ_12864) - #define ULTRA_LCD + #define IS_ULTRA_LCD #define DOGLCD - #define ULTIMAKERCONTROLLER + #define IS_ULTIPANEL #if ENABLED(miniVIKI) #define LCD_CONTRAST_MIN 75 @@ -95,24 +87,24 @@ #elif ENABLED(OLED_PANEL_TINYBOY2) - #define U8GLIB_SSD1306 - #define ULTIPANEL + #define IS_U8GLIB_SSD1306 + #define IS_ULTIPANEL #elif ENABLED(RA_CONTROL_PANEL) #define LCD_I2C_TYPE_PCA8574 #define LCD_I2C_ADDRESS 0x27 // I2C Address of the port expander - #define ULTIPANEL + #define IS_ULTIPANEL #elif ENABLED(REPRAPWORLD_GRAPHICAL_LCD) #define DOGLCD #define U8GLIB_ST7920 - #define ULTIPANEL + #define IS_ULTIPANEL #elif ENABLED(CR10_STOCKDISPLAY) - #define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER + #define IS_RRD_FG_SC #ifndef ST7920_DELAY_1 #define ST7920_DELAY_1 DELAY_NS(125) #endif @@ -125,13 +117,13 @@ #elif ENABLED(MKS_12864OLED) - #define REPRAP_DISCOUNT_SMART_CONTROLLER + #define IS_RRD_SC #define U8GLIB_SH1106 #elif ENABLED(MKS_12864OLED_SSD1306) - #define REPRAP_DISCOUNT_SMART_CONTROLLER - #define U8GLIB_SSD1306 + #define IS_RRD_SC + #define IS_U8GLIB_SSD1306 #elif ENABLED(MKS_MINI_12864) @@ -143,12 +135,12 @@ #define FYSETC_MINI_12864 #define DOGLCD - #define ULTIPANEL + #define IS_ULTIPANEL #define LCD_CONTRAST_MIN 0 #define LCD_CONTRAST_MAX 255 #define DEFAULT_LCD_CONTRAST 220 #define LED_COLORS_REDUCE_GREEN - #if (HAS_POWER_SWITCH && EITHER(FYSETC_MINI_12864_2_0, FYSETC_MINI_12864_2_1)) + #if HAS_POWER_SWITCH && EITHER(FYSETC_MINI_12864_2_0, FYSETC_MINI_12864_2_1) #define LED_BACKLIGHT_TIMEOUT 10000 #endif @@ -159,25 +151,19 @@ #define NEOPIXEL_LED #undef NEOPIXEL_TYPE #define NEOPIXEL_TYPE NEO_RGB - #undef NEOPIXEL_PIXELS - #define NEOPIXEL_PIXELS 3 + #if NEOPIXEL_PIXELS < 3 + #undef NEOPIXELS_PIXELS + #define NEOPIXEL_PIXELS 3 + #endif #ifndef NEOPIXEL_BRIGHTNESS #define NEOPIXEL_BRIGHTNESS 127 #endif - #define NEOPIXEL_STARTUP_TEST + //#define NEOPIXEL_STARTUP_TEST #endif -#endif +#elif ENABLED(ULTI_CONTROLLER) -#if EITHER(MAKRPANEL, MINIPANEL) - #define DOGLCD - #define ULTIPANEL - #ifndef DEFAULT_LCD_CONTRAST - #define DEFAULT_LCD_CONTRAST 17 - #endif -#endif - -#if ENABLED(ULTI_CONTROLLER) + #define IS_ULTIPANEL #define U8GLIB_SSD1309 #define LCD_RESET_PIN LCD_PINS_D6 // This controller need a reset pin #define LCD_CONTRAST_MIN 0 @@ -185,67 +171,95 @@ #define DEFAULT_LCD_CONTRAST 127 #define ENCODER_PULSES_PER_STEP 2 #define ENCODER_STEPS_PER_MENU_ITEM 2 -#endif - -// 128x64 I2C OLED LCDs - SSD1306/SSD1309/SH1106 -#define HAS_SSD1306_OLED_I2C ANY(U8GLIB_SSD1306, U8GLIB_SSD1309, U8GLIB_SH1106) -#if HAS_SSD1306_OLED_I2C - #define ULTRA_LCD - #define DOGLCD -#endif - -#if EITHER(PANEL_ONE, U8GLIB_SH1106) - - #define ULTIMAKERCONTROLLER #elif ENABLED(MAKEBOARD_MINI_2_LINE_DISPLAY_1602) - #define REPRAP_DISCOUNT_SMART_CONTROLLER + #define IS_RRD_SC #define LCD_WIDTH 16 #define LCD_HEIGHT 2 #endif -#if ANY(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER, LCD_FOR_MELZI, SILVER_GATE_GLCD_CONTROLLER) +#if ENABLED(IS_RRD_FG_SC) + #define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER +#endif + +#if EITHER(MAKRPANEL, MINIPANEL) + #define IS_ULTIPANEL #define DOGLCD - #define U8GLIB_ST7920 - #define REPRAP_DISCOUNT_SMART_CONTROLLER -#endif - -#if ANY(ULTIMAKERCONTROLLER, REPRAP_DISCOUNT_SMART_CONTROLLER, G3D_PANEL, RIGIDBOT_PANEL, ULTI_CONTROLLER) - #define ULTIPANEL -#endif - -#if ENABLED(REPRAPWORLD_KEYPAD) - #define NEWPANEL - #if ENABLED(ULTIPANEL) && !defined(REPRAPWORLD_KEYPAD_MOVE_STEP) - #define REPRAPWORLD_KEYPAD_MOVE_STEP 1.0 + #if ENABLED(MAKRPANEL) + #define U8GLIB_ST7565_64128N + #endif + #ifndef DEFAULT_LCD_CONTRAST + #define DEFAULT_LCD_CONTRAST 17 #endif #endif +#if ENABLED(IS_U8GLIB_SSD1306) + #define U8GLIB_SSD1306 +#endif + +#if ENABLED(OVERLORD_OLED) + #define IS_ULTIPANEL + #define U8GLIB_SH1106 + /** + * PCA9632 for buzzer and LEDs via i2c + * No auto-inc, red and green leds switched, buzzer + */ + #define PCA9632 + #define PCA9632_NO_AUTO_INC + #define PCA9632_GRN 0x00 + #define PCA9632_RED 0x02 + #define PCA9632_BUZZER + #define PCA9632_BUZZER_DATA { 0x09, 0x02 } + + #define ENCODER_PULSES_PER_STEP 1 // Overlord uses buttons + #define ENCODER_STEPS_PER_MENU_ITEM 1 +#endif + +// 128x64 I2C OLED LCDs - SSD1306/SSD1309/SH1106 +#define HAS_SSD1306_OLED_I2C ANY(U8GLIB_SSD1306, U8GLIB_SSD1309, U8GLIB_SH1106) +#if HAS_SSD1306_OLED_I2C + #define IS_ULTRA_LCD + #define DOGLCD +#endif + +// ST7920-based graphical displays +#if ANY(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER, LCD_FOR_MELZI, SILVER_GATE_GLCD_CONTROLLER) + #define DOGLCD + #define U8GLIB_ST7920 + #define IS_RRD_SC +#endif + +// RepRapDiscount LCD or Graphical LCD with rotary click encoder +#if ENABLED(IS_RRD_SC) + #define REPRAP_DISCOUNT_SMART_CONTROLLER +#endif + /** - * SPI PANELS + * SPI Ultipanels */ - // Einstart OLED has Cardinal nav via pins defined in pins_EINSTART-S.h - #if ENABLED(U8GLIB_SH1106_EINSTART) - #define ULTRA_LCD - #define DOGLCD - #define ULTIPANEL - #define NEWPANEL - #endif +// Basic Ultipanel-like displays +#if ANY(ULTIMAKERCONTROLLER, REPRAP_DISCOUNT_SMART_CONTROLLER, G3D_PANEL, RIGIDBOT_PANEL, PANEL_ONE, U8GLIB_SH1106) + #define IS_ULTIPANEL +#endif - /** - * FSMC/SPI TFT PANELS - */ - #if ENABLED(MKS_ROBIN_TFT) - #define ULTRA_LCD - #define DOGLCD - #define ULTIPANEL - #endif +// Einstart OLED has Cardinal nav via pins defined in pins_EINSTART-S.h +#if ENABLED(U8GLIB_SH1106_EINSTART) + #define DOGLCD + #define IS_ULTIPANEL +#endif + +// FSMC/SPI TFT Panels +#if ENABLED(FSMC_GRAPHICAL_TFT) + #define DOGLCD + #define IS_ULTIPANEL + #define DELAYED_BACKLIGHT_INIT +#endif /** - * I2C PANELS + * I2C Panels */ #if EITHER(LCD_SAINSMART_I2C_1602, LCD_SAINSMART_I2C_2004) @@ -265,7 +279,7 @@ #define LCD_I2C_TYPE_MCP23017 #define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander #define LCD_USE_I2C_BUZZER // Enable buzzer on LCD (optional) - #define ULTIPANEL + #define IS_ULTIPANEL #elif ENABLED(LCD_I2C_VIKI) @@ -280,7 +294,7 @@ #define LCD_I2C_TYPE_MCP23017 #define LCD_I2C_ADDRESS 0x20 // I2C Address of the port expander #define LCD_USE_I2C_BUZZER // Enable buzzer on LCD (requires LiquidTWI2 v1.2.3 or later) - #define ULTIPANEL + #define IS_ULTIPANEL #define ENCODER_FEEDRATE_DEADZONE 4 @@ -292,7 +306,7 @@ #define STD_ENCODER_PULSES_PER_STEP 2 #define STD_ENCODER_STEPS_PER_MENU_ITEM 1 -#elif ANY(miniVIKI, VIKI2, ELB_FULL_GRAPHIC_CONTROLLER, AZSMZ_12864, OLED_PANEL_TINYBOY2, BQ_LCD_SMART_CONTROLLER, LCD_I2C_PANELOLU2, REPRAP_DISCOUNT_SMART_CONTROLLER) +#elif ANY(REPRAP_DISCOUNT_SMART_CONTROLLER, miniVIKI, VIKI2, ELB_FULL_GRAPHIC_CONTROLLER, AZSMZ_12864, OLED_PANEL_TINYBOY2, BQ_LCD_SMART_CONTROLLER, LCD_I2C_PANELOLU2) #define STD_ENCODER_PULSES_PER_STEP 4 #define STD_ENCODER_STEPS_PER_MENU_ITEM 1 @@ -321,21 +335,41 @@ // https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/schematics#!shiftregister-connection #if ENABLED(FF_INTERFACEBOARD) #define SR_LCD_3W_NL // Non latching 3 wire shift register - #define ULTIPANEL -#endif - -#if ENABLED(SAV_3DLCD) + #define IS_ULTIPANEL +#elif ENABLED(SAV_3DLCD) #define SR_LCD_2W_NL // Non latching 2 wire shift register - #define ULTIPANEL + #define IS_ULTIPANEL #endif +#if ENABLED(IS_ULTIPANEL) + #define ULTIPANEL +#endif #if ENABLED(ULTIPANEL) - #define NEWPANEL // Disable this if you actually have no click-encoder panel + #define IS_ULTRA_LCD + #ifndef NEWPANEL + #define NEWPANEL + #endif +#endif + +#if ENABLED(IS_ULTRA_LCD) #define ULTRA_LCD #endif +#if ENABLED(IS_RRW_KEYPAD) + #define REPRAPWORLD_KEYPAD +#endif + +// Keypad needs a move step +#if ENABLED(REPRAPWORLD_KEYPAD) + #define NEWPANEL + #ifndef REPRAPWORLD_KEYPAD_MOVE_STEP + #define REPRAPWORLD_KEYPAD_MOVE_STEP 1.0 + #endif +#endif + // Extensible UI serial touch screens. (See src/lcd/extensible_ui) -#if EITHER(DGUS_LCD, MALYAN_LCD) +#if EITHER(MALYAN_LCD, DGUS_LCD) + #define IS_EXTUI #define EXTENSIBLE_UI #endif @@ -345,8 +379,7 @@ #define HAS_GRAPHICAL_LCD ENABLED(DOGLCD) #define HAS_CHARACTER_LCD (HAS_SPI_LCD && !HAS_GRAPHICAL_LCD) #define HAS_LCD_MENU (ENABLED(ULTIPANEL) && DISABLED(NO_LCD_MENUS)) - -#define HAS_ADC_BUTTONS ENABLED(ADC_KEYPAD) +#define HAS_ADC_BUTTONS ENABLED(ADC_KEYPAD) /** * Default LCD contrast for Graphical LCD displays @@ -592,3 +625,5 @@ #endif #define IS_RE_ARM_BOARD (MB(RAMPS_14_RE_ARM_EFB) || MB(RAMPS_14_RE_ARM_EEB) || MB(RAMPS_14_RE_ARM_EFF) || MB(RAMPS_14_RE_ARM_EEF) || MB(RAMPS_14_RE_ARM_SF)) + +#define HAS_SDCARD_CONNECTION EITHER(TARGET_LPC1768, ADAFRUIT_GRAND_CENTRAL_M4) diff --git a/Marlin/src/inc/Conditionals_post.h b/Marlin/src/inc/Conditionals_post.h index 5fc46fa0d5..b9216ddd0e 100644 --- a/Marlin/src/inc/Conditionals_post.h +++ b/Marlin/src/inc/Conditionals_post.h @@ -909,7 +909,7 @@ #define HAS_TMCX1X0 (HAS_DRIVER(TMC2130) || HAS_DRIVER(TMC2160) || HAS_DRIVER(TMC5130) || HAS_DRIVER(TMC5160)) #define TMC_HAS_SPI (HAS_TMCX1X0 || HAS_DRIVER(TMC2660)) #define HAS_STALLGUARD (HAS_TMCX1X0 || HAS_DRIVER(TMC2209) || HAS_DRIVER(TMC2660)) - #define HAS_STEALTHCHOP (HAS_TMCX1X0 || HAS_DRIVER(TMC2208) || HAS_DRIVER(TMC2209)) + #define HAS_STEALTHCHOP (HAS_TMCX1X0 || HAS_TMC220x) #define STEALTHCHOP_ENABLED ANY(STEALTHCHOP_XY, STEALTHCHOP_Z, STEALTHCHOP_E) #define USE_SENSORLESS EITHER(SENSORLESS_HOMING, SENSORLESS_PROBING) @@ -1000,11 +1000,11 @@ #define HAS_CONTROLLER_FAN (PIN_EXISTS(CONTROLLER_FAN)) // Servos -#define HAS_SERVO_0 (PIN_EXISTS(SERVO0)) -#define HAS_SERVO_1 (PIN_EXISTS(SERVO1)) -#define HAS_SERVO_2 (PIN_EXISTS(SERVO2)) -#define HAS_SERVO_3 (PIN_EXISTS(SERVO3)) -#define HAS_SERVOS (defined(NUM_SERVOS) && NUM_SERVOS > 0) +#define HAS_SERVO_0 (PIN_EXISTS(SERVO0) && NUM_SERVOS > 0) +#define HAS_SERVO_1 (PIN_EXISTS(SERVO1) && NUM_SERVOS > 1) +#define HAS_SERVO_2 (PIN_EXISTS(SERVO2) && NUM_SERVOS > 2) +#define HAS_SERVO_3 (PIN_EXISTS(SERVO3) && NUM_SERVOS > 3) +#define HAS_SERVOS (NUM_SERVOS > 0) #if HAS_SERVOS && !defined(Z_PROBE_SERVO_NR) #define Z_PROBE_SERVO_NR -1 @@ -1024,7 +1024,7 @@ #define HAS_KILL (PIN_EXISTS(KILL)) #define HAS_SUICIDE (PIN_EXISTS(SUICIDE)) #define HAS_PHOTOGRAPH (PIN_EXISTS(PHOTOGRAPH)) -#define HAS_BUZZER (PIN_EXISTS(BEEPER) || ENABLED(LCD_USE_I2C_BUZZER)) +#define HAS_BUZZER (PIN_EXISTS(BEEPER) || ENABLED(LCD_USE_I2C_BUZZER) || ENABLED(PCA9632_BUZZER)) #define HAS_CASE_LIGHT (PIN_EXISTS(CASE_LIGHT) && ENABLED(CASE_LIGHT_ENABLE)) // Digital control @@ -1153,10 +1153,17 @@ #define WRITE_HEATER_0(v) WRITE_HEATER_0P(v) #endif +#ifndef MIN_POWER + #define MIN_POWER 0 +#endif + /** * Heated bed requires settings */ #if HAS_HEATED_BED + #ifndef MIN_BED_POWER + #define MIN_BED_POWER 0 + #endif #ifndef MAX_BED_POWER #define MAX_BED_POWER 255 #endif @@ -1360,7 +1367,7 @@ #define _PROBE_RADIUS (DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE)) #ifndef DELTA_CALIBRATION_RADIUS #ifdef X_PROBE_OFFSET_FROM_EXTRUDER - #define DELTA_CALIBRATION_RADIUS (DELTA_PRINTABLE_RADIUS - MAX(ABS(X_PROBE_OFFSET_FROM_EXTRUDER), ABS(Y_PROBE_OFFSET_FROM_EXTRUDER), ABS(MIN_PROBE_EDGE))) + #define DELTA_CALIBRATION_RADIUS (DELTA_PRINTABLE_RADIUS - _MAX(ABS(X_PROBE_OFFSET_FROM_EXTRUDER), ABS(Y_PROBE_OFFSET_FROM_EXTRUDER), ABS(MIN_PROBE_EDGE))) #else #define DELTA_CALIBRATION_RADIUS _PROBE_RADIUS #endif @@ -1398,10 +1405,10 @@ #else // Boundaries for Cartesian probing based on bed limits - #define _MIN_PROBE_X (MAX(X_MIN_BED + MIN_PROBE_EDGE, X_MIN_POS + X_PROBE_OFFSET_FROM_EXTRUDER)) - #define _MIN_PROBE_Y (MAX(Y_MIN_BED + MIN_PROBE_EDGE, Y_MIN_POS + Y_PROBE_OFFSET_FROM_EXTRUDER)) - #define _MAX_PROBE_X (MIN(X_MAX_BED - (MIN_PROBE_EDGE), X_MAX_POS + X_PROBE_OFFSET_FROM_EXTRUDER)) - #define _MAX_PROBE_Y (MIN(Y_MAX_BED - (MIN_PROBE_EDGE), Y_MAX_POS + Y_PROBE_OFFSET_FROM_EXTRUDER)) + #define _MIN_PROBE_X (_MAX(X_MIN_BED + MIN_PROBE_EDGE, X_MIN_POS + X_PROBE_OFFSET_FROM_EXTRUDER)) + #define _MIN_PROBE_Y (_MAX(Y_MIN_BED + MIN_PROBE_EDGE, Y_MIN_POS + Y_PROBE_OFFSET_FROM_EXTRUDER)) + #define _MAX_PROBE_X (_MIN(X_MAX_BED - (MIN_PROBE_EDGE), X_MAX_POS + X_PROBE_OFFSET_FROM_EXTRUDER)) + #define _MAX_PROBE_Y (_MIN(Y_MAX_BED - (MIN_PROBE_EDGE), Y_MAX_POS + Y_PROBE_OFFSET_FROM_EXTRUDER)) #endif @@ -1438,15 +1445,15 @@ #else // Boundaries for Cartesian probing based on set limits #if ENABLED(AUTO_BED_LEVELING_UBL) - #define _MESH_MIN_X (MAX(X_MIN_BED + MESH_INSET, X_MIN_POS)) // UBL is careful not to probe off the bed. It does not - #define _MESH_MIN_Y (MAX(Y_MIN_BED + MESH_INSET, Y_MIN_POS)) // need *_PROBE_OFFSET_FROM_EXTRUDER in the mesh dimensions - #define _MESH_MAX_X (MIN(X_MAX_BED - (MESH_INSET), X_MAX_POS)) - #define _MESH_MAX_Y (MIN(Y_MAX_BED - (MESH_INSET), Y_MAX_POS)) + #define _MESH_MIN_X (_MAX(X_MIN_BED + MESH_INSET, X_MIN_POS)) // UBL is careful not to probe off the bed. It does not + #define _MESH_MIN_Y (_MAX(Y_MIN_BED + MESH_INSET, Y_MIN_POS)) // need *_PROBE_OFFSET_FROM_EXTRUDER in the mesh dimensions + #define _MESH_MAX_X (_MIN(X_MAX_BED - (MESH_INSET), X_MAX_POS)) + #define _MESH_MAX_Y (_MIN(Y_MAX_BED - (MESH_INSET), Y_MAX_POS)) #else - #define _MESH_MIN_X (MAX(X_MIN_BED + MESH_INSET, X_MIN_POS + X_PROBE_OFFSET_FROM_EXTRUDER)) - #define _MESH_MIN_Y (MAX(Y_MIN_BED + MESH_INSET, Y_MIN_POS + Y_PROBE_OFFSET_FROM_EXTRUDER)) - #define _MESH_MAX_X (MIN(X_MAX_BED - (MESH_INSET), X_MAX_POS + X_PROBE_OFFSET_FROM_EXTRUDER)) - #define _MESH_MAX_Y (MIN(Y_MAX_BED - (MESH_INSET), Y_MAX_POS + Y_PROBE_OFFSET_FROM_EXTRUDER)) + #define _MESH_MIN_X (_MAX(X_MIN_BED + MESH_INSET, X_MIN_POS + X_PROBE_OFFSET_FROM_EXTRUDER)) + #define _MESH_MIN_Y (_MAX(Y_MIN_BED + MESH_INSET, Y_MIN_POS + Y_PROBE_OFFSET_FROM_EXTRUDER)) + #define _MESH_MAX_X (_MIN(X_MAX_BED - (MESH_INSET), X_MAX_POS + X_PROBE_OFFSET_FROM_EXTRUDER)) + #define _MESH_MAX_Y (_MIN(Y_MAX_BED - (MESH_INSET), Y_MAX_POS + Y_PROBE_OFFSET_FROM_EXTRUDER)) #endif #endif @@ -1551,7 +1558,7 @@ /** * Make sure DOGLCD_SCK and DOGLCD_MOSI are defined. */ -#if ENABLED(DOGLCD) +#if HAS_GRAPHICAL_LCD #ifndef DOGLCD_SCK #define DOGLCD_SCK SCK_PIN #endif @@ -1660,8 +1667,9 @@ #endif // Force SDCARD_SORT_ALPHA to be enabled for Graphical LCD on LPC1768 +// on boards where SD card and LCD display share the same SPI bus // because of a bug in the shared SPI implementation. (See #8122) -#if defined(TARGET_LPC1768) && ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) +#if defined(TARGET_LPC1768) && ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) && (SCK_PIN == LCD_PINS_D4) #define SDCARD_SORT_ALPHA // Keeps one directory level in RAM. Changing // directory levels still glitches the screen, // but the following LCD update cleans it up. @@ -1737,3 +1745,7 @@ #define INIT_SDCARD_ON_BOOT #endif #endif + +#if !NUM_SERIAL + #undef BAUD_RATE_GCODE +#endif diff --git a/Marlin/src/inc/MarlinConfig.h b/Marlin/src/inc/MarlinConfig.h index 94aa1939ba..bb974e64d9 100644 --- a/Marlin/src/inc/MarlinConfig.h +++ b/Marlin/src/inc/MarlinConfig.h @@ -27,24 +27,19 @@ #include "MarlinConfigPre.h" -#include HAL_PATH(../HAL, HAL.h) +#include "../HAL/HAL.h" #include "../pins/pins.h" - #include HAL_PATH(../HAL, spi_pins.h) -#if defined(__AVR__) && !defined(USBCON) - #define HardwareSerial_h // trick to disable the standard HWserial -#endif - #include "Conditionals_post.h" -#include "SanityCheck.h" +#include HAL_PATH(../HAL, inc/Conditionals_post.h) -#include HAL_PATH(../HAL, SanityCheck.h) +#include "SanityCheck.h" +#include HAL_PATH(../HAL, inc/SanityCheck.h) // Include all core headers #include "../core/enum.h" #include "../core/language.h" #include "../core/utility.h" #include "../core/serial.h" -#include "../core/minmax.h" diff --git a/Marlin/src/inc/MarlinConfigPre.h b/Marlin/src/inc/MarlinConfigPre.h index ef998c654a..63c5a6095d 100644 --- a/Marlin/src/inc/MarlinConfigPre.h +++ b/Marlin/src/inc/MarlinConfigPre.h @@ -28,12 +28,18 @@ // #include "../HAL/platforms.h" + #include "../core/boards.h" #include "../core/macros.h" #include "../core/millis_t.h" #include "Version.h" #include "../../Configuration.h" + #include "Conditionals_LCD.h" +#include HAL_PATH(../HAL, inc/Conditionals_LCD.h) + #include "../core/drivers.h" #include "../../Configuration_adv.h" + #include "Conditionals_adv.h" +#include HAL_PATH(../HAL, inc/Conditionals_adv.h) diff --git a/Marlin/src/inc/SanityCheck.h b/Marlin/src/inc/SanityCheck.h index 1f2498b8a2..e6bd1beb1d 100644 --- a/Marlin/src/inc/SanityCheck.h +++ b/Marlin/src/inc/SanityCheck.h @@ -382,12 +382,17 @@ #error "Replace POWER_SUPPLY 2 by enabling PSU_CONTROL and setting PSU_ACTIVE_HIGH to 'true'." #elif defined(POWER_SUPPLY) #error "POWER_SUPPLY is now obsolete. Please remove it from Configuration.h." +#elif defined(MKS_ROBIN_TFT) + #error "MKS_ROBIN_TFT is now FSMC_GRAPHICAL_TFT. Please update your configuration." +#elif defined(SDPOWER) + #error "SDPOWER is now SDPOWER_PIN. Please update your configuration and/or pins." #endif -#define BOARD_MKS_13 -47 -#define BOARD_TRIGORILLA -343 -#define BOARD_RURAMPS4D -1550 -#define BOARD_FORMBOT_TREX2 -81 +#define BOARD_MKS_13 -1109 +#define BOARD_TRIGORILLA -1131 +#define BOARD_RURAMPS4D -3020 +#define BOARD_FORMBOT_TREX2 -1125 +#define BOARD_BIQU_SKR_V1_1 -2014 #if MB(MKS_13) #error "BOARD_MKS_13 has been renamed BOARD_MKS_GEN_13. Please update your configuration." #elif MB(TRIGORILLA) @@ -396,11 +401,14 @@ #error "BOARD_RURAMPS4D has been renamed BOARD_RURAMPS4D_11. Please update your configuration." #elif MB(FORMBOT_TREX2) #error "FORMBOT_TREX2 has been renamed BOARD_FORMBOT_TREX2PLUS. Please update your configuration." +#elif MB(BOARD_BIQU_SKR_V1_1) + #error "BIQU_SKR_V1_1 has been renamed BOARD_BIGTREE_SKR_V1_1. Please update your configuration." #endif #undef BOARD_MKS_13 #undef BOARD_TRIGORILLA #undef BOARD_RURAMPS4D #undef BOARD_FORMBOT_TREX2 +#undef BOARD_BIQU_SKR_V1_1 /** * Marlin release, version and default string @@ -477,7 +485,7 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS #if ENABLED(MIN_SOFTWARE_ENDSTOPS) && DISABLED(MIN_SOFTWARE_ENDSTOP_Z) #if IS_KINEMATIC #error "MIN_SOFTWARE_ENDSTOPS on DELTA/SCARA also requires MIN_SOFTWARE_ENDSTOP_Z." - #elif DISABLED(MIN_SOFTWARE_ENDSTOP_X, MIN_SOFTWARE_ENDSTOP_Y) + #elif NONE(MIN_SOFTWARE_ENDSTOP_X, MIN_SOFTWARE_ENDSTOP_Y) #error "MIN_SOFTWARE_ENDSTOPS requires at least one of the MIN_SOFTWARE_ENDSTOP_[XYZ] options." #endif #endif @@ -485,19 +493,17 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS #if ENABLED(MAX_SOFTWARE_ENDSTOPS) && DISABLED(MAX_SOFTWARE_ENDSTOP_Z) #if IS_KINEMATIC #error "MAX_SOFTWARE_ENDSTOPS on DELTA/SCARA also requires MAX_SOFTWARE_ENDSTOP_Z." - #elif DISABLED(MAX_SOFTWARE_ENDSTOP_X, MAX_SOFTWARE_ENDSTOP_Y) + #elif NONE(MAX_SOFTWARE_ENDSTOP_X, MAX_SOFTWARE_ENDSTOP_Y) #error "MAX_SOFTWARE_ENDSTOPS requires at least one of the MAX_SOFTWARE_ENDSTOP_[XYZ] options." #endif #endif -#if !defined(TARGET_LPC1768) && ( \ - ENABLED(ENDSTOPPULLDOWNS) \ - || ENABLED(ENDSTOPPULLDOWN_XMAX) \ - || ENABLED(ENDSTOPPULLDOWN_YMAX) \ - || ENABLED(ENDSTOPPULLDOWN_ZMAX) \ - || ENABLED(ENDSTOPPULLDOWN_XMIN) \ - || ENABLED(ENDSTOPPULLDOWN_YMIN) \ - || ENABLED(ENDSTOPPULLDOWN_ZMIN) ) +#if !defined(TARGET_LPC1768) && ANY( \ + ENDSTOPPULLDOWNS, \ + ENDSTOPPULLDOWN_XMAX, ENDSTOPPULLDOWN_YMAX, \ + ENDSTOPPULLDOWN_ZMAX, ENDSTOPPULLDOWN_XMIN, \ + ENDSTOPPULLDOWN_YMIN, ENDSTOPPULLDOWN_ZMIN \ + ) #error "PULLDOWN pin mode is not available on the selected board." #endif @@ -534,7 +540,7 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS * Progress Bar */ #if ENABLED(LCD_PROGRESS_BAR) - #if DISABLED(SDSUPPORT, LCD_SET_PROGRESS_MANUALLY) + #if NONE(SDSUPPORT, LCD_SET_PROGRESS_MANUALLY) #error "LCD_PROGRESS_BAR requires SDSUPPORT or LCD_SET_PROGRESS_MANUALLY." #elif !HAS_CHARACTER_LCD #error "LCD_PROGRESS_BAR requires a character LCD." @@ -552,7 +558,7 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS /** * Custom Boot and Status screens */ -#if DISABLED(DOGLCD) && EITHER(SHOW_CUSTOM_BOOTSCREEN, CUSTOM_STATUS_SCREEN_IMAGE) +#if EITHER(SHOW_CUSTOM_BOOTSCREEN, CUSTOM_STATUS_SCREEN_IMAGE) && !HAS_GRAPHICAL_LCD #error "Graphical LCD is required for SHOW_CUSTOM_BOOTSCREEN and CUSTOM_STATUS_SCREEN_IMAGE." #endif @@ -598,7 +604,7 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS * I2C Position Encoders */ #if ENABLED(I2C_POSITION_ENCODERS) - #if DISABLED(BABYSTEPPING) || DISABLED(BABYSTEP_XY) + #if !BOTH(BABYSTEPPING, BABYSTEP_XY) #error "I2C_POSITION_ENCODERS requires BABYSTEPPING and BABYSTEP_XY." #elif !WITHIN(I2CPE_ENCODER_CNT, 1, 5) #error "I2CPE_ENCODER_CNT must be between 1 and 5." @@ -617,7 +623,7 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS #error "MESH_BED_LEVELING and BABYSTEP_ZPROBE_OFFSET is not a valid combination" #elif ENABLED(BABYSTEP_ZPROBE_OFFSET) && !HAS_BED_PROBE #error "BABYSTEP_ZPROBE_OFFSET requires a probe." - #elif ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY) && DISABLED(DOGLCD) + #elif ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY) && !HAS_GRAPHICAL_LCD #error "BABYSTEP_ZPROBE_GFX_OVERLAY requires a Graphical LCD." #elif ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY) && DISABLED(BABYSTEP_ZPROBE_OFFSET) #error "BABYSTEP_ZPROBE_GFX_OVERLAY requires a BABYSTEP_ZPROBE_OFFSET." @@ -646,7 +652,7 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS #error "FILAMENT_RUNOUT_SENSOR with NUM_RUNOUT_SENSORS > 4 requires FIL_RUNOUT5_PIN." #elif NUM_RUNOUT_SENSORS > 5 && !PIN_EXISTS(FIL_RUNOUT6) #error "FILAMENT_RUNOUT_SENSOR with NUM_RUNOUT_SENSORS > 5 requires FIL_RUNOUT6_PIN." - #elif DISABLED(SDSUPPORT, PRINTJOB_TIMER_AUTOSTART) + #elif NONE(SDSUPPORT, PRINTJOB_TIMER_AUTOSTART) #error "FILAMENT_RUNOUT_SENSOR requires SDSUPPORT or PRINTJOB_TIMER_AUTOSTART." #elif FILAMENT_RUNOUT_DISTANCE_MM < 0 #error "FILAMENT_RUNOUT_DISTANCE_MM must be greater than or equal to zero." @@ -663,7 +669,7 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS #error "ADVANCED_PAUSE_FEATURE currently requires an LCD controller or EMERGENCY_PARSER." #elif ENABLED(EXTRUDER_RUNOUT_PREVENT) #error "EXTRUDER_RUNOUT_PREVENT is incompatible with ADVANCED_PAUSE_FEATURE." - #elif ENABLED(PARK_HEAD_ON_PAUSE) && DISABLED(SDSUPPORT, NEWPANEL, EMERGENCY_PARSER) + #elif ENABLED(PARK_HEAD_ON_PAUSE) && NONE(SDSUPPORT, NEWPANEL, EMERGENCY_PARSER) #error "PARK_HEAD_ON_PAUSE requires SDSUPPORT, EMERGENCY_PARSER, or an LCD controller." #elif ENABLED(HOME_BEFORE_FILAMENT_CHANGE) && DISABLED(PAUSE_PARK_NO_STEPPER_TIMEOUT) #error "HOME_BEFORE_FILAMENT_CHANGE requires PAUSE_PARK_NO_STEPPER_TIMEOUT." @@ -905,12 +911,11 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS #endif #endif -#if ANY(MAGNETIC_SWITCHING_TOOLHEAD, ELECTROMAGNETIC_SWITCHING_TOOLHEAD) - #if ENABLED(EXT_SOLENOID) - #error "(ELECTRO)MAGNETIC_SWITCHING_TOOLHEAD and EXT_SOLENOID are incompatible. (Pins are used twice.)" - #elif !PIN_EXISTS(SOL0) - #error "(ELECTRO)MAGNETIC_SWITCHING_TOOLHEAD requires SOL0_PIN." - #elif !defined(SWITCHING_TOOLHEAD_Y_POS) +/** + * (Electro)magnetic Switching Toolhead requirements + */ +#if EITHER(MAGNETIC_SWITCHING_TOOLHEAD, ELECTROMAGNETIC_SWITCHING_TOOLHEAD) + #ifndef SWITCHING_TOOLHEAD_Y_POS #error "(ELECTRO)MAGNETIC_SWITCHING_TOOLHEAD requires SWITCHING_TOOLHEAD_Y_POS" #elif !defined(SWITCHING_TOOLHEAD_X_POS) #error "(ELECTRO)MAGNETIC_SWITCHING_TOOLHEAD requires SWITCHING_TOOLHEAD_X_POS" @@ -918,6 +923,12 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS #error "(ELECTRO)MAGNETIC_SWITCHING_TOOLHEAD requires SWITCHING_TOOLHEAD_Z_HOP." #elif !defined(SWITCHING_TOOLHEAD_Y_CLEAR) #error "(ELECTRO)MAGNETIC_SWITCHING_TOOLHEAD requires SWITCHING_TOOLHEAD_Y_CLEAR." + #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) + #if ENABLED(EXT_SOLENOID) + #error "(ELECTRO)MAGNETIC_SWITCHING_TOOLHEAD and EXT_SOLENOID are incompatible. (Pins are used twice.)" + #elif !PIN_EXISTS(SOL0) + #error "(ELECTRO)MAGNETIC_SWITCHING_TOOLHEAD requires SOL0_PIN." + #endif #endif #endif @@ -949,7 +960,7 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS /** * Required LCD language */ -#if DISABLED(DOGLCD) && ENABLED(ULTRA_LCD) && !defined(DISPLAY_CHARSET_HD44780) +#if HAS_CHARACTER_LCD && !defined(DISPLAY_CHARSET_HD44780) #error "You must set DISPLAY_CHARSET_HD44780 to JAPANESE, WESTERN or CYRILLIC for your LCD controller." #endif @@ -983,7 +994,7 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS * Delta requirements */ #if ENABLED(DELTA) - #if DISABLED(USE_XMAX_PLUG, USE_YMAX_PLUG, USE_ZMAX_PLUG) + #if NONE(USE_XMAX_PLUG, USE_YMAX_PLUG, USE_ZMAX_PLUG) #error "You probably want to use Max Endstops for DELTA!" #elif ENABLED(ENABLE_LEVELING_FADE_HEIGHT) && DISABLED(AUTO_BED_LEVELING_BILINEAR) && !UBL_SEGMENTED #error "ENABLE_LEVELING_FADE_HEIGHT on DELTA requires AUTO_BED_LEVELING_BILINEAR or AUTO_BED_LEVELING_UBL." @@ -1252,7 +1263,7 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS #error "G26_MESH_VALIDATION requires MESH_BED_LEVELING, AUTO_BED_LEVELING_BILINEAR, or AUTO_BED_LEVELING_UBL." #endif -#if ENABLED(MESH_EDIT_GFX_OVERLAY) && (DISABLED(AUTO_BED_LEVELING_UBL) || DISABLED(DOGLCD)) +#if ENABLED(MESH_EDIT_GFX_OVERLAY) && !(ENABLED(AUTO_BED_LEVELING_UBL) && HAS_GRAPHICAL_LCD) #error "MESH_EDIT_GFX_OVERLAY requires AUTO_BED_LEVELING_UBL and a Graphical LCD." #endif @@ -1326,7 +1337,7 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS /** * ULTIPANEL encoder */ -#if ENABLED(ULTIPANEL) && DISABLED(NEWPANEL, SR_LCD_2W_NL) && !defined(SHIFT_CLK) +#if ENABLED(ULTIPANEL) && NONE(NEWPANEL, SR_LCD_2W_NL) && !defined(SHIFT_CLK) #error "ULTIPANEL requires some kind of encoder." #endif @@ -1338,7 +1349,7 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS * SAV_3DGLCD display options */ #if ENABLED(SAV_3DGLCD) - #if DISABLED(U8GLIB_SSD1306, U8GLIB_SH1106) + #if NONE(U8GLIB_SSD1306, U8GLIB_SH1106) #error "Enable a SAV_3DGLCD display type: U8GLIB_SSD1306 or U8GLIB_SH1106." #elif BOTH(U8GLIB_SSD1306, U8GLIB_SH1106) #error "Only enable one SAV_3DGLCD display type: U8GLIB_SSD1306 or U8GLIB_SH1106." @@ -1408,10 +1419,14 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS #endif /** - * Test case light not using the same pin as the fan + * Case Light requirements */ -#if ENABLED(CASE_LIGHT_ENABLE) && CASE_LIGHT_PIN == FAN_PIN - #error "You cannot set CASE_LIGHT_PIN equal to FAN_PIN." +#if ENABLED(CASE_LIGHT_ENABLE) + #if !PIN_EXISTS(CASE_LIGHT) + #error "CASE_LIGHT_ENABLE requires CASE_LIGHT_PIN to be defined." + #elif CASE_LIGHT_PIN == FAN_PIN + #error "CASE_LIGHT_PIN conflicts with FAN_PIN. Resolve before continuing." + #endif #endif /** @@ -1555,7 +1570,7 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS * LED Backlight Timeout */ #if defined(LED_BACKLIGHT_TIMEOUT) && !(EITHER(FYSETC_MINI_12864_2_0, FYSETC_MINI_12864_2_1) && HAS_POWER_SWITCH) - #error "LED_BACKLIGHT_TIMEOUT requires a Fysetc Mini Panel and a Power Switch." + #error "LED_BACKLIGHT_TIMEOUT requires a FYSETC Mini Panel and a Power Switch." #endif /** @@ -1826,76 +1841,69 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS /** * Make sure only one display is enabled - * - * Note: BQ_LCD_SMART_CONTROLLER => REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER - * REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER => REPRAP_DISCOUNT_SMART_CONTROLLER - * SAV_3DGLCD => U8GLIB_SH1106 => ULTIMAKERCONTROLLER - * MKS_12864OLED => U8GLIB_SH1106 => ULTIMAKERCONTROLLER - * MKS_12864OLED_SSD1306 => U8GLIB_SSD1306 => ULTIMAKERCONTROLLER - * MKS_MINI_12864 => MINIPANEL - * miniVIKI => ULTIMAKERCONTROLLER - * VIKI2 => ULTIMAKERCONTROLLER - * ELB_FULL_GRAPHIC_CONTROLLER => ULTIMAKERCONTROLLER - * AZSMZ_12864 => ULTIMAKERCONTROLLER - * PANEL_ONE => ULTIMAKERCONTROLLER */ #if 1 < 0 \ - + ( ENABLED(ULTIMAKERCONTROLLER) \ - && DISABLED(SAV_3DGLCD) \ - && DISABLED(miniVIKI) \ - && DISABLED(VIKI2) \ - && DISABLED(ELB_FULL_GRAPHIC_CONTROLLER) \ - && DISABLED(AZSMZ_12864) \ - && DISABLED(PANEL_ONE) \ - && DISABLED(MKS_12864OLED) \ - && DISABLED(MKS_12864OLED_SSD1306) ) \ - + ( ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) \ - && DISABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) \ - && DISABLED(LCD_FOR_MELZI) \ - && DISABLED(MAKEBOARD_MINI_2_LINE_DISPLAY_1602) \ - && DISABLED(MKS_12864OLED) \ - && DISABLED(MKS_12864OLED_SSD1306) ) \ - + (ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) && DISABLED(BQ_LCD_SMART_CONTROLLER)) \ - + ENABLED(LCD_FOR_MELZI) \ - + ENABLED(MKS_12864OLED) \ - + ENABLED(MKS_12864OLED_SSD1306) \ - + ENABLED(MAKEBOARD_MINI_2_LINE_DISPLAY_1602) \ - + ENABLED(CARTESIO_UI) \ - + ENABLED(PANEL_ONE) \ - + ENABLED(MAKRPANEL) \ - + ENABLED(REPRAPWORLD_GRAPHICAL_LCD) \ - + ENABLED(VIKI2) \ - + ENABLED(miniVIKI) \ - + ENABLED(ELB_FULL_GRAPHIC_CONTROLLER) \ - + ENABLED(AZSMZ_12864) \ - + ENABLED(G3D_PANEL) \ + + (ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) && DISABLED(IS_RRD_SC)) \ + + (ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) && DISABLED(IS_RRD_FG_SC)) \ + + (ENABLED(ULTRA_LCD) && DISABLED(IS_ULTRA_LCD)) \ + + (ENABLED(U8GLIB_SSD1306) && DISABLED(IS_U8GLIB_SSD1306)) \ + (ENABLED(MINIPANEL) && DISABLED(MKS_MINI_12864)) \ - + ENABLED(MKS_MINI_12864) \ - + ENABLED(FYSETC_MINI_12864_X_X) \ - + ENABLED(FYSETC_MINI_12864_1_2) \ - + ENABLED(FYSETC_MINI_12864_2_0) \ - + ENABLED(FYSETC_MINI_12864_2_1) \ - + (ENABLED(REPRAPWORLD_KEYPAD) && DISABLED(CARTESIO_UI, ZONESTAR_LCD)) \ + + (ENABLED(REPRAPWORLD_KEYPAD) && DISABLED(IS_RRW_KEYPAD)) \ + + (ENABLED(EXTENSIBLE_UI) && DISABLED(IS_EXTUI)) \ + + (ENABLED(ULTIPANEL) && DISABLED(IS_ULTIPANEL)) \ + + ENABLED(RADDS_DISPLAY) \ + + ENABLED(ULTIMAKERCONTROLLER) \ + + ENABLED(PANEL_ONE) \ + + ENABLED(G3D_PANEL) \ + ENABLED(RIGIDBOT_PANEL) \ + + ENABLED(MAKEBOARD_MINI_2_LINE_DISPLAY_1602) \ + + ENABLED(ZONESTAR_LCD) \ + ENABLED(RA_CONTROL_PANEL) \ + ENABLED(LCD_SAINSMART_I2C_1602) \ + ENABLED(LCD_SAINSMART_I2C_2004) \ + ENABLED(LCM1602) \ + ENABLED(LCD_I2C_PANELOLU2) \ + ENABLED(LCD_I2C_VIKI) \ - + (ENABLED(U8GLIB_SSD1306) && DISABLED(OLED_PANEL_TINYBOY2, MKS_12864OLED_SSD1306)) \ + ENABLED(SAV_3DLCD) \ + + ENABLED(FF_INTERFACEBOARD) \ + + ENABLED(REPRAPWORLD_GRAPHICAL_LCD) \ + + ENABLED(VIKI2) \ + + ENABLED(miniVIKI) \ + + ENABLED(MAKRPANEL) \ + + ENABLED(ELB_FULL_GRAPHIC_CONTROLLER) \ + ENABLED(BQ_LCD_SMART_CONTROLLER) \ + + ENABLED(CARTESIO_UI) \ + + ENABLED(LCD_FOR_MELZI) \ + + ENABLED(ULTI_CONTROLLER) \ + + ENABLED(MKS_MINI_12864) \ + + ENABLED(FYSETC_MINI_12864_X_X) \ + + ENABLED(FYSETC_MINI_12864_1_2) \ + + ENABLED(FYSETC_MINI_12864_2_0) \ + + ENABLED(FYSETC_MINI_12864_2_1) \ + + ENABLED(CR10_STOCKDISPLAY) \ + + ENABLED(ANET_FULL_GRAPHICS_LCD) \ + + ENABLED(AZSMZ_12864) \ + + ENABLED(SILVER_GATE_GLCD_CONTROLLER) \ + ENABLED(SAV_3DGLCD) \ + ENABLED(OLED_PANEL_TINYBOY2) \ - + ENABLED(ZONESTAR_LCD) \ - + ENABLED(ULTI_CONTROLLER) \ - + ENABLED(MALYAN_LCD) \ + + ENABLED(MKS_12864OLED) \ + + ENABLED(MKS_12864OLED_SSD1306) \ + + ENABLED(U8GLIB_SH1106_EINSTART) \ + + ENABLED(OVERLORD_OLED) \ + ENABLED(DGUS_LCD) \ - + (ENABLED(EXTENSIBLE_UI) && DISABLED(MALYAN_LCD, DGUS_LCD)) + + ENABLED(MALYAN_LCD) \ + + ENABLED(FSMC_GRAPHICAL_TFT) #error "Please select no more than one LCD controller option." #endif +#undef IS_RRD_SC +#undef IS_RRD_FG_SC +#undef IS_ULTRA_LCD +#undef IS_U8GLIB_SSD1306 +#undef IS_RRW_KEYPAD +#undef IS_EXTUI +#undef IS_ULTIPANEL + /** * FYSETC Mini 12864 RGB backlighting required */ @@ -2007,7 +2015,7 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS /** * TMC2208/2209 software UART and ENDSTOP_INTERRUPTS both use pin change interrupts (PCI) */ -#if (HAS_DRIVER(TMC2208) || HAS_DRIVER(TMC2209)) && ENABLED(ENDSTOP_INTERRUPTS_FEATURE) && !( \ +#if HAS_TMC220x && !defined(TARGET_LPC1768) && ENABLED(ENDSTOP_INTERRUPTS_FEATURE) && !( \ defined(X_HARDWARE_SERIAL ) \ || defined(X2_HARDWARE_SERIAL) \ || defined(Y_HARDWARE_SERIAL ) \ @@ -2025,22 +2033,23 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS #endif /** - * TMC2208/2209 software UART is only supported on AVR and LPC + * TMC2208/2209 software UART is only supported on AVR, LPC, STM32F1 and STM32F4 */ -#if (HAS_DRIVER(TMC2208) || HAS_DRIVER(TMC2209)) && !defined(__AVR__) && !defined(TARGET_LPC1768) && !( \ +#if HAS_TMC220x && !defined(__AVR__) && !defined(TARGET_LPC1768) && !defined(TARGET_STM32F1) && !defined(TARGET_STM32F4) && !( \ defined(X_HARDWARE_SERIAL ) \ || defined(X2_HARDWARE_SERIAL) \ || defined(Y_HARDWARE_SERIAL ) \ || defined(Y2_HARDWARE_SERIAL) \ || defined(Z_HARDWARE_SERIAL ) \ || defined(Z2_HARDWARE_SERIAL) \ + || defined(Z3_HARDWARE_SERIAL) \ || defined(E0_HARDWARE_SERIAL) \ || defined(E1_HARDWARE_SERIAL) \ || defined(E2_HARDWARE_SERIAL) \ || defined(E3_HARDWARE_SERIAL) \ || defined(E4_HARDWARE_SERIAL) \ || defined(E5_HARDWARE_SERIAL) ) - #error "TMC2208 Software Serial is supported only on AVR and LPC1768 platforms." + #error "TMC2208 Software Serial is supported only on AVR, LPC1768, STM32F1 and STM32F4 platforms." #endif #if ENABLED(SENSORLESS_HOMING) @@ -2057,17 +2066,17 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS #if ENABLED(DELTA) && !BOTH(STEALTHCHOP_XY, STEALTHCHOP_Z) #error "SENSORLESS_HOMING on DELTA currently requires STEALTHCHOP_XY and STEALTHCHOP_Z." - #elif X_SENSORLESS && X_HOME_DIR == -1 && (X_MIN_ENDSTOP_INVERTING != X_ENDSTOP_INVERTING || DISABLED(ENDSTOPPULLUP_XMIN)) + #elif X_SENSORLESS && X_HOME_DIR < 0 && (X_MIN_ENDSTOP_INVERTING != X_ENDSTOP_INVERTING || DISABLED(ENDSTOPPULLUP_XMIN)) #error "SENSORLESS_HOMING requires X_MIN_ENDSTOP_INVERTING and ENDSTOPPULLUP_XMIN when homing to X_MIN." - #elif X_SENSORLESS && X_HOME_DIR == 1 && (X_MAX_ENDSTOP_INVERTING != X_ENDSTOP_INVERTING || DISABLED(ENDSTOPPULLUP_XMAX)) + #elif X_SENSORLESS && X_HOME_DIR > 0 && (X_MAX_ENDSTOP_INVERTING != X_ENDSTOP_INVERTING || DISABLED(ENDSTOPPULLUP_XMAX)) #error "SENSORLESS_HOMING requires X_MAX_ENDSTOP_INVERTING and ENDSTOPPULLUP_XMAX when homing to X_MAX." - #elif Y_SENSORLESS && Y_HOME_DIR == -1 && (Y_MIN_ENDSTOP_INVERTING != Y_ENDSTOP_INVERTING || DISABLED(ENDSTOPPULLUP_YMIN)) + #elif Y_SENSORLESS && Y_HOME_DIR < 0 && (Y_MIN_ENDSTOP_INVERTING != Y_ENDSTOP_INVERTING || DISABLED(ENDSTOPPULLUP_YMIN)) #error "SENSORLESS_HOMING requires Y_MIN_ENDSTOP_INVERTING and ENDSTOPPULLUP_YMIN when homing to Y_MIN." - #elif Y_SENSORLESS && Y_HOME_DIR == 1 && (Y_MAX_ENDSTOP_INVERTING != Y_ENDSTOP_INVERTING || DISABLED(ENDSTOPPULLUP_YMAX)) + #elif Y_SENSORLESS && Y_HOME_DIR > 0 && (Y_MAX_ENDSTOP_INVERTING != Y_ENDSTOP_INVERTING || DISABLED(ENDSTOPPULLUP_YMAX)) #error "SENSORLESS_HOMING requires Y_MAX_ENDSTOP_INVERTING and ENDSTOPPULLUP_YMAX when homing to Y_MAX." - #elif Z_SENSORLESS && Z_HOME_DIR == -1 && (Z_MIN_ENDSTOP_INVERTING != Z_ENDSTOP_INVERTING || DISABLED(ENDSTOPPULLUP_ZMIN)) + #elif Z_SENSORLESS && Z_HOME_DIR < 0 && (Z_MIN_ENDSTOP_INVERTING != Z_ENDSTOP_INVERTING || DISABLED(ENDSTOPPULLUP_ZMIN)) #error "SENSORLESS_HOMING requires Z_MIN_ENDSTOP_INVERTING and ENDSTOPPULLUP_ZMIN when homing to Z_MIN." - #elif Z_SENSORLESS && Z_HOME_DIR == 1 && (Z_MAX_ENDSTOP_INVERTING != Z_ENDSTOP_INVERTING || DISABLED(ENDSTOPPULLUP_ZMAX)) + #elif Z_SENSORLESS && Z_HOME_DIR > 0 && (Z_MAX_ENDSTOP_INVERTING != Z_ENDSTOP_INVERTING || DISABLED(ENDSTOPPULLUP_ZMAX)) #error "SENSORLESS_HOMING requires Z_MAX_ENDSTOP_INVERTING and ENDSTOPPULLUP_ZMAX when homing to Z_MAX." #elif ENDSTOP_NOISE_THRESHOLD #error "SENSORLESS_HOMING is incompatible with ENDSTOP_NOISE_THRESHOLD." @@ -2130,7 +2139,7 @@ constexpr float sanity_arr_1[] = DEFAULT_AXIS_STEPS_PER_UNIT, sanity_arr_2[] = DEFAULT_MAX_FEEDRATE, sanity_arr_3[] = DEFAULT_MAX_ACCELERATION; -#define _ARR_TEST(N,I) (sanity_arr_##N[MIN(I,int(COUNT(sanity_arr_##N))-1)] > 0) +#define _ARR_TEST(N,I) (sanity_arr_##N[_MIN(I,int(COUNT(sanity_arr_##N))-1)] > 0) static_assert(COUNT(sanity_arr_1) >= XYZE, "DEFAULT_AXIS_STEPS_PER_UNIT requires X, Y, Z and E elements."); static_assert(COUNT(sanity_arr_1) <= XYZE_N, "DEFAULT_AXIS_STEPS_PER_UNIT has too many elements. (Did you forget to enable DISTINCT_E_FACTORS?)"); diff --git a/Marlin/src/inc/Version.h b/Marlin/src/inc/Version.h index b71d71779a..eea40ed5c5 100644 --- a/Marlin/src/inc/Version.h +++ b/Marlin/src/inc/Version.h @@ -38,7 +38,7 @@ /** * Marlin release version identifier */ - #define SHORT_BUILD_VERSION "2.0.x_R16" + #define SHORT_BUILD_VERSION "2.0.x_R17" /** * Verbose version identifier which should contain a reference to the location @@ -51,7 +51,7 @@ * here we define this default string as the date where the latest release * version was tagged. */ - #define STRING_DISTRIBUTION_DATE "2019-07-05" + #define STRING_DISTRIBUTION_DATE "2019-08-02" /** * Required minimum Configuration.h and Configuration_adv.h file versions. diff --git a/Marlin/src/lcd/HD44780/ultralcd_HD44780.cpp b/Marlin/src/lcd/HD44780/ultralcd_HD44780.cpp index 0f3c1251ca..b40aab6e09 100644 --- a/Marlin/src/lcd/HD44780/ultralcd_HD44780.cpp +++ b/Marlin/src/lcd/HD44780/ultralcd_HD44780.cpp @@ -112,7 +112,7 @@ static void createChar_P(const char c, const byte * const ptr) { #endif void MarlinUI::set_custom_characters(const HD44780CharSet screen_charset/*=CHARSET_INFO*/) { - #if DISABLED(LCD_PROGRESS_BAR, SHOW_BOOTSCREEN) + #if NONE(LCD_PROGRESS_BAR, SHOW_BOOTSCREEN) UNUSED(screen_charset); #endif @@ -382,7 +382,7 @@ void MarlinUI::clear_lcd() { lcd.clear(); } } else { PGM_P p = text; - int dly = time / MAX(slen, 1); + int dly = time / _MAX(slen, 1); for (uint8_t i = 0; i <= slen; i++) { // Go to the correct place @@ -516,7 +516,7 @@ FORCE_INLINE void _draw_axis_value(const AxisEnum axis, const char *value, const if (!TEST(axis_homed, axis)) while (const char c = *value++) lcd_put_wchar(c <= '.' ? c : '?'); else { - #if DISABLED(HOME_AFTER_DEACTIVATE, DISABLE_REDUCED_ACCURACY_WARNING) + #if NONE(HOME_AFTER_DEACTIVATE, DISABLE_REDUCED_ACCURACY_WARNING) if (!TEST(axis_known_position, axis)) lcd_put_u8str_P(axis == Z_AXIS ? PSTR(" ") : PSTR(" ")); else @@ -1024,6 +1024,8 @@ void MarlinUI::draw_status_screen() { } void draw_edit_screen(PGM_P const pstr, const char* const value/*=nullptr*/) { + ui.encoder_direction_normal(); + lcd_moveto(0, 1); lcd_put_u8str_P(pstr); if (value != nullptr) { @@ -1325,7 +1327,7 @@ void MarlinUI::draw_status_screen() { */ clear_custom_char(&new_char); - const uint8_t ypix = MIN(upper_left.y_pixel_offset + pixels_per_y_mesh_pnt, HD44780_CHAR_HEIGHT); + const uint8_t ypix = _MIN(upper_left.y_pixel_offset + pixels_per_y_mesh_pnt, HD44780_CHAR_HEIGHT); for (j = upper_left.y_pixel_offset; j < ypix; j++) { i = upper_left.x_pixel_mask; for (k = 0; k < pixels_per_x_mesh_pnt; k++) { diff --git a/Marlin/src/lcd/dogm/HAL_LCD_com_defines.h b/Marlin/src/lcd/dogm/HAL_LCD_com_defines.h index c9b112ced8..efd326c2b7 100644 --- a/Marlin/src/lcd/dogm/HAL_LCD_com_defines.h +++ b/Marlin/src/lcd/dogm/HAL_LCD_com_defines.h @@ -25,7 +25,6 @@ #ifndef U8G_HAL_LINKS - #ifdef __SAM3X8E__ uint8_t u8g_com_HAL_DUE_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_ptr); #define U8G_COM_HAL_SW_SPI_FN u8g_com_HAL_DUE_sw_spi_fn @@ -33,34 +32,41 @@ #define U8G_COM_HAL_HW_SPI_FN u8g_com_HAL_DUE_shared_hw_spi_fn uint8_t u8g_com_HAL_DUE_ST7920_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_ptr); #define U8G_COM_ST7920_HAL_SW_SPI u8g_com_HAL_DUE_ST7920_sw_spi_fn + #define U8G_COM_ST7920_HAL_HW_SPI u8g_com_arduino_st7920_hw_spi_fn #elif defined(__STM32F1__) uint8_t u8g_com_HAL_STM32F1_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_ptr); #define U8G_COM_HAL_SW_SPI_FN u8g_com_HAL_STM32F1_sw_spi_fn - uint8_t u8g_com_arduino_hw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_ptr); - #define U8G_COM_HAL_HW_SPI_FN u8g_com_arduino_hw_spi_fn - uint8_t u8g_com_arduino_st7920_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_ptr); + #define U8G_COM_HAL_HW_SPI_FN u8g_com_stm32duino_hw_spi_fn + #define U8G_COM_ST7920_HAL_SW_SPI u8g_com_std_sw_spi_fn + #define U8G_COM_ST7920_HAL_HW_SPI u8g_com_stm32duino_hw_spi_fn + #elif defined(ARDUINO_ARCH_STM32) + #define U8G_COM_HAL_SW_SPI_FN u8g_com_arduino_std_sw_spi_fn + #define U8G_COM_HAL_HW_SPI_FN u8g_com_stm32duino_hw_spi_fn #define U8G_COM_ST7920_HAL_SW_SPI u8g_com_arduino_st7920_spi_fn - #else + #define U8G_COM_ST7920_HAL_HW_SPI u8g_com_stm32duino_hw_spi_fn + #elif defined(__AVR__) uint8_t u8g_com_HAL_AVR_sw_sp_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_ptr); - #define U8G_COM_HAL_SW_SPI_FN u8g_com_HAL_AVR_sw_sp_fn // AVR ? - uint8_t u8g_com_arduino_hw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_ptr); + #define U8G_COM_HAL_SW_SPI_FN u8g_com_HAL_AVR_sw_sp_fn #define U8G_COM_HAL_HW_SPI_FN u8g_com_arduino_hw_spi_fn - uint8_t u8g_com_arduino_st7920_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_ptr); #define U8G_COM_ST7920_HAL_SW_SPI u8g_com_arduino_st7920_spi_fn + #define U8G_COM_ST7920_HAL_HW_SPI u8g_com_arduino_st7920_hw_spi_fn + #else + #define U8G_COM_HAL_SW_SPI_FN u8g_com_arduino_std_sw_spi_fn + #define U8G_COM_HAL_HW_SPI_FN u8g_com_arduino_hw_spi_fn + #define U8G_COM_ST7920_HAL_SW_SPI u8g_com_arduino_st7920_spi_fn + #define U8G_COM_ST7920_HAL_HW_SPI u8g_com_arduino_st7920_hw_spi_fn #endif - uint8_t u8g_com_arduino_st7920_hw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_ptr); - #define U8G_COM_ST7920_HAL_HW_SPI u8g_com_arduino_st7920_hw_spi_fn - uint8_t u8g_com_HAL_LPC1768_ssd_hw_i2c_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_ptr); #define U8G_COM_SSD_I2C_HAL u8g_com_arduino_ssd_i2c_fn - #if defined(ARDUINO_ARCH_STM32F1) && PIN_EXISTS(FSMC_CS) + #if PIN_EXISTS(FSMC_CS) uint8_t u8g_com_stm32duino_fsmc_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_ptr); #define U8G_COM_HAL_FSMC_FN u8g_com_stm32duino_fsmc_fn #else #define U8G_COM_HAL_FSMC_FN u8g_com_null_fn #endif + #elif TARGET_LPC1768 uint8_t u8g_com_HAL_LPC1768_sw_spi_fn(u8g_t *u8g, uint8_t msg, uint8_t arg_val, void *arg_ptr); #define U8G_COM_HAL_SW_SPI_FN u8g_com_HAL_LPC1768_sw_spi_fn diff --git a/Marlin/src/lcd/dogm/dogm_Statusscreen.h b/Marlin/src/lcd/dogm/dogm_Statusscreen.h index 8031db2d73..6f0d10831a 100644 --- a/Marlin/src/lcd/dogm/dogm_Statusscreen.h +++ b/Marlin/src/lcd/dogm/dogm_Statusscreen.h @@ -1170,7 +1170,7 @@ #define STATUS_LOGO_X 0 #endif #ifndef STATUS_LOGO_Y - #define STATUS_LOGO_Y MIN(0, 10 - (STATUS_LOGO_HEIGHT) / 2) + #define STATUS_LOGO_Y _MIN(0, 10 - (STATUS_LOGO_HEIGHT) / 2) #endif #ifndef STATUS_LOGO_HEIGHT #define STATUS_LOGO_HEIGHT (sizeof(status_logo_bmp) / (STATUS_LOGO_BYTEWIDTH)) diff --git a/Marlin/src/lcd/dogm/status_screen_DOGM.cpp b/Marlin/src/lcd/dogm/status_screen_DOGM.cpp index 62e52fff20..f04d2e89a5 100644 --- a/Marlin/src/lcd/dogm/status_screen_DOGM.cpp +++ b/Marlin/src/lcd/dogm/status_screen_DOGM.cpp @@ -56,14 +56,6 @@ #include "../../feature/mixing.h" #endif -FORCE_INLINE void _draw_centered_temp(const int16_t temp, const uint8_t tx, const uint8_t ty) { - const char *str = i16tostr3(temp); - const uint8_t len = str[0] != ' ' ? 3 : str[1] != ' ' ? 2 : 1; - lcd_moveto(tx - len * (INFO_FONT_WIDTH) / 2 + 1, ty); - lcd_put_u8str(&str[3-len]); - lcd_put_wchar(LCD_STR_DEGREE[0]); -} - #define X_LABEL_POS 3 #define X_VALUE_POS 11 #define XYZ_SPACING 37 @@ -96,7 +88,7 @@ FORCE_INLINE void _draw_centered_temp(const int16_t temp, const uint8_t tx, cons #define CHAMBER_ALT() false #endif -#define MAX_HOTEND_DRAW MIN(HOTENDS, ((LCD_PIXEL_WIDTH - (STATUS_LOGO_BYTEWIDTH + STATUS_FAN_BYTEWIDTH) * 8) / (STATUS_HEATERS_XSPACE))) +#define MAX_HOTEND_DRAW _MIN(HOTENDS, ((LCD_PIXEL_WIDTH - (STATUS_LOGO_BYTEWIDTH + STATUS_FAN_BYTEWIDTH) * 8) / (STATUS_HEATERS_XSPACE))) #define STATUS_HEATERS_BOT (STATUS_HEATERS_Y + STATUS_HEATERS_HEIGHT - 1) #if ENABLED(MARLIN_DEV_MODE) @@ -105,6 +97,14 @@ FORCE_INLINE void _draw_centered_temp(const int16_t temp, const uint8_t tx, cons #define SHOW_ON_STATE false #endif +FORCE_INLINE void _draw_centered_temp(const int16_t temp, const uint8_t tx, const uint8_t ty) { + const char *str = i16tostr3(temp); + const uint8_t len = str[0] != ' ' ? 3 : str[1] != ' ' ? 2 : 1; + lcd_moveto(tx - len * (INFO_FONT_WIDTH) / 2 + 1, ty); + lcd_put_u8str(&str[3-len]); + lcd_put_wchar(LCD_STR_DEGREE[0]); +} + FORCE_INLINE void _draw_heater_status(const heater_ind_t heater, const bool blink) { #if !HEATER_IDLE_HANDLER UNUSED(blink); @@ -133,27 +133,6 @@ FORCE_INLINE void _draw_heater_status(const heater_ind_t heater, const bool blin target = IFBED(thermalManager.degTargetBed(), thermalManager.degTargetHotend(heater)); #endif - #if HAS_HEATED_CHAMBER - FORCE_INLINE void _draw_chamber_status(const bool blink) { - const float temp = thermalManager.degChamber(), - target = thermalManager.degTargetChamber(); - #if !HEATER_IDLE_HANDLER - UNUSED(blink); - #endif - if (PAGE_UNDER(7)) { - #if HEATER_IDLE_HANDLER - const bool is_idle = false, // thermalManager.chamber_idle.timed_out, - dodraw = (blink || !is_idle); - #else - constexpr bool dodraw = true; - #endif - if (dodraw) _draw_centered_temp(target + 0.5, STATUS_CHAMBER_TEXT_X, 7); - } - if (PAGE_CONTAINS(28 - INFO_FONT_ASCENT, 28 - 1)) - _draw_centered_temp(temp + 0.5f, STATUS_CHAMBER_TEXT_X, 28); - } - #endif - #if DISABLED(STATUS_HOTEND_ANIM) #define STATIC_HOTEND true #define HOTEND_DOT isHeat @@ -255,6 +234,29 @@ FORCE_INLINE void _draw_heater_status(const heater_ind_t heater, const bool blin } +#if HAS_HEATED_CHAMBER + + FORCE_INLINE void _draw_chamber_status(const bool blink) { + const float temp = thermalManager.degChamber(), + target = thermalManager.degTargetChamber(); + #if !HEATER_IDLE_HANDLER + UNUSED(blink); + #endif + if (PAGE_UNDER(7)) { + #if HEATER_IDLE_HANDLER + const bool is_idle = false, // thermalManager.chamber_idle.timed_out, + dodraw = (blink || !is_idle); + #else + constexpr bool dodraw = true; + #endif + if (dodraw) _draw_centered_temp(target + 0.5, STATUS_CHAMBER_TEXT_X, 7); + } + if (PAGE_CONTAINS(28 - INFO_FONT_ASCENT, 28 - 1)) + _draw_centered_temp(temp + 0.5f, STATUS_CHAMBER_TEXT_X, 28); + } + +#endif + // // Before homing, blink '123' <-> '???'. // Homed but unknown... '123' <-> ' '. @@ -271,7 +273,7 @@ FORCE_INLINE void _draw_axis_value(const AxisEnum axis, const char *value, const if (!TEST(axis_homed, axis)) while (const char c = *value++) lcd_put_wchar(c <= '.' ? c : '?'); else { - #if DISABLED(HOME_AFTER_DEACTIVATE, DISABLE_REDUCED_ACCURACY_WARNING) + #if NONE(HOME_AFTER_DEACTIVATE, DISABLE_REDUCED_ACCURACY_WARNING) if (!TEST(axis_known_position, axis)) lcd_put_u8str_P(axis == Z_AXIS ? PSTR(" ") : PSTR(" ")); else @@ -358,7 +360,7 @@ void MarlinUI::draw_status_screen() { #endif #if DO_DRAW_CHAMBER - #if ANIM_HAMBER + #if ANIM_CHAMBER #define CHAMBER_BITMAP(S) ((S) ? status_chamber_on_bmp : status_chamber_bmp) #else #define CHAMBER_BITMAP(S) status_chamber_bmp diff --git a/Marlin/src/lcd/dogm/status_screen_lite_ST7920.cpp b/Marlin/src/lcd/dogm/status_screen_lite_ST7920.cpp index 20c360f519..a4001f67d1 100644 --- a/Marlin/src/lcd/dogm/status_screen_lite_ST7920.cpp +++ b/Marlin/src/lcd/dogm/status_screen_lite_ST7920.cpp @@ -59,6 +59,8 @@ #include "../../sd/cardreader.h" #endif +#define TEXT_MODE_LCD_WIDTH 16 + #define BUFFER_WIDTH 256 #define BUFFER_HEIGHT 32 @@ -619,13 +621,12 @@ void ST7920_Lite_Status_Screen::draw_status_message() { set_ddram_address(DDRAM_LINE_4); begin_data(); #if ENABLED(STATUS_MESSAGE_SCROLLING) - uint8_t slen = utf8_strlen(str); - if (slen <= LCD_WIDTH) { + if (slen <= TEXT_MODE_LCD_WIDTH) { // String fits the LCD, so just print it write_str(str); - while (slen < LCD_WIDTH) { write_byte(' '); ++slen; } + while (slen < TEXT_MODE_LCD_WIDTH) { write_byte(' '); ++slen; } } else { // String is larger than the available space in screen. @@ -634,12 +635,12 @@ void ST7920_Lite_Status_Screen::draw_status_message() { // and the string remaining length uint8_t rlen; const char *stat = ui.status_and_len(rlen); - write_str(stat, LCD_WIDTH); + write_str(stat, TEXT_MODE_LCD_WIDTH); // If the remaining string doesn't completely fill the screen - if (rlen < LCD_WIDTH) { + if (rlen < TEXT_MODE_LCD_WIDTH) { write_byte('.'); // Always at 1+ spaces left, draw a dot - uint8_t chars = LCD_WIDTH - rlen; // Amount of space left in characters + uint8_t chars = TEXT_MODE_LCD_WIDTH - rlen; // Amount of space left in characters if (--chars) { // Draw a second dot if there's space write_byte('.'); if (--chars) write_str(str, chars); // Print a second copy of the message @@ -651,8 +652,8 @@ void ST7920_Lite_Status_Screen::draw_status_message() { #else uint8_t slen = utf8_strlen(str); - write_str(str, LCD_WIDTH); - for (; slen < LCD_WIDTH; ++slen) write_byte(' '); + write_str(str, TEXT_MODE_LCD_WIDTH); + for (; slen < TEXT_MODE_LCD_WIDTH; ++slen) write_byte(' '); #endif } @@ -760,7 +761,8 @@ bool ST7920_Lite_Status_Screen::position_changed() { bool ST7920_Lite_Status_Screen::status_changed() { uint8_t checksum = 0; for (const char *p = ui.status_message; *p; p++) checksum ^= *p; - static uint8_t last_checksum = 0, changed = last_checksum != checksum; + static uint8_t last_checksum = 0; + bool changed = last_checksum != checksum; if (changed) last_checksum = checksum; return changed; } @@ -805,7 +807,7 @@ void ST7920_Lite_Status_Screen::update_status_or_position(bool forceUpdate) { } #if !STATUS_EXPIRE_SECONDS #if ENABLED(STATUS_MESSAGE_SCROLLING) - else + else if (blink_changed()) draw_status_message(); #endif #else diff --git a/Marlin/src/lcd/dogm/u8g_dev_tft_320x240_upscale_from_128x64.cpp b/Marlin/src/lcd/dogm/u8g_dev_tft_320x240_upscale_from_128x64.cpp index ca3d7f5757..dfd327e2a1 100644 --- a/Marlin/src/lcd/dogm/u8g_dev_tft_320x240_upscale_from_128x64.cpp +++ b/Marlin/src/lcd/dogm/u8g_dev_tft_320x240_upscale_from_128x64.cpp @@ -61,28 +61,59 @@ #include "U8glib.h" #include "HAL_LCD_com_defines.h" -#include "string.h" +#include + +#if ENABLED(LCD_USE_DMA_FSMC) + extern void LCD_IO_WriteSequence(uint16_t *data, uint16_t length); + extern void LCD_IO_WriteSequence_Async(uint16_t *data, uint16_t length); + extern void LCD_IO_WaitSequence_Async(); + extern void LCD_IO_WriteMultiple(uint16_t color, uint32_t count); +#endif #define WIDTH 128 #define HEIGHT 64 #define PAGE_HEIGHT 8 -#define X_MIN 32 -#define Y_MIN 56 -#define X_MAX (X_MIN + 2 * WIDTH - 1) -#define Y_MAX (Y_MIN + 2 * HEIGHT - 1) +#define X_LO 32 +#define Y_LO 32 +#define X_HI (X_LO + 2 * WIDTH - 1) +#define Y_HI (Y_LO + 2 * HEIGHT - 1) #define LCD_COLUMN 0x2A /* Colomn address register */ #define LCD_ROW 0x2B /* Row address register */ #define LCD_WRITE_RAM 0x2C +// see https://ee-programming-notepad.blogspot.com/2016/10/16-bit-color-generator-picker.html + +#define COLOR_BLACK 0x0000 +#define COLOR_WHITE 0xFFFF +#define COLOR_BLUE 0x21DD +#define COLOR_RED 0xF800 +#define COLOR_DARK 0x0003 // Some dark color + +#ifndef TFT_MARLINUI_COLOR + #define TFT_MARLINUI_COLOR COLOR_WHITE +#endif +#ifndef TFT_MARLINBG_COLOR + #define TFT_MARLINBG_COLOR COLOR_BLACK +#endif +#ifndef TFT_DISABLED_COLOR + #define TFT_DISABLED_COLOR COLOR_DARK +#endif +#ifndef TFT_BTSLEFT_COLOR + #define TFT_BTSLEFT_COLOR COLOR_BLUE +#endif +#ifndef TFT_BTRIGHT_COLOR + #define TFT_BTRIGHT_COLOR COLOR_RED +#endif + static uint32_t lcd_id = 0; #define U8G_ESC_DATA(x) (uint8_t)(x >> 8), (uint8_t)(x & 0xFF) static const uint8_t page_first_sequence[] = { - U8G_ESC_ADR(0), LCD_COLUMN, U8G_ESC_ADR(1), U8G_ESC_DATA(X_MIN), U8G_ESC_DATA(X_MAX), - U8G_ESC_ADR(0), LCD_ROW, U8G_ESC_ADR(1), U8G_ESC_DATA(Y_MIN), U8G_ESC_DATA(Y_MAX), + U8G_ESC_ADR(0), LCD_COLUMN, U8G_ESC_ADR(1), U8G_ESC_DATA(X_LO), U8G_ESC_DATA(X_HI), + U8G_ESC_ADR(0), LCD_ROW, U8G_ESC_ADR(1), U8G_ESC_DATA(Y_LO), U8G_ESC_DATA(Y_HI), U8G_ESC_ADR(0), LCD_WRITE_RAM, U8G_ESC_ADR(1), U8G_ESC_END }; @@ -94,6 +125,45 @@ static const uint8_t clear_screen_sequence[] = { U8G_ESC_END }; +#if ENABLED(TOUCH_BUTTONS) + + static const uint8_t separation_line_sequence_left[] = { + U8G_ESC_ADR(0), LCD_COLUMN, U8G_ESC_ADR(1), U8G_ESC_DATA(10), U8G_ESC_DATA(159), + U8G_ESC_ADR(0), LCD_ROW, U8G_ESC_ADR(1), U8G_ESC_DATA(170), U8G_ESC_DATA(173), + U8G_ESC_ADR(0), LCD_WRITE_RAM, U8G_ESC_ADR(1), + U8G_ESC_END + }; + + static const uint8_t separation_line_sequence_right[] = { + U8G_ESC_ADR(0), LCD_COLUMN, U8G_ESC_ADR(1), U8G_ESC_DATA(160), U8G_ESC_DATA(309), + U8G_ESC_ADR(0), LCD_ROW, U8G_ESC_ADR(1), U8G_ESC_DATA(170), U8G_ESC_DATA(173), + U8G_ESC_ADR(0), LCD_WRITE_RAM, U8G_ESC_ADR(1), + U8G_ESC_END + }; + + static const uint8_t button0_sequence[] = { + U8G_ESC_ADR(0), LCD_COLUMN, U8G_ESC_ADR(1), U8G_ESC_DATA(20), U8G_ESC_DATA(99), + U8G_ESC_ADR(0), LCD_ROW, U8G_ESC_ADR(1), U8G_ESC_DATA(185), U8G_ESC_DATA(224), + U8G_ESC_ADR(0), LCD_WRITE_RAM, U8G_ESC_ADR(1), + U8G_ESC_END + }; + + static const uint8_t button1_sequence[] = { + U8G_ESC_ADR(0), LCD_COLUMN, U8G_ESC_ADR(1), U8G_ESC_DATA(120), U8G_ESC_DATA(199), + U8G_ESC_ADR(0), LCD_ROW, U8G_ESC_ADR(1), U8G_ESC_DATA(185), U8G_ESC_DATA(224), + U8G_ESC_ADR(0), LCD_WRITE_RAM, U8G_ESC_ADR(1), + U8G_ESC_END + }; + + static const uint8_t button2_sequence[] = { + U8G_ESC_ADR(0), LCD_COLUMN, U8G_ESC_ADR(1), U8G_ESC_DATA(220), U8G_ESC_DATA(299), + U8G_ESC_ADR(0), LCD_ROW, U8G_ESC_ADR(1), U8G_ESC_DATA(185), U8G_ESC_DATA(224), + U8G_ESC_ADR(0), LCD_WRITE_RAM, U8G_ESC_ADR(1), + U8G_ESC_END + }; + +#endif + static const uint8_t st7789v_init_sequence[] = { // 0x8552 - ST7789V U8G_ESC_ADR(0), 0x10, @@ -120,53 +190,253 @@ static const uint8_t st7789v_init_sequence[] = { // 0x8552 - ST7789V U8G_ESC_END }; +static const uint8_t ili9341_init_sequence[] = { // 0x9341 - ILI9341 + U8G_ESC_ADR(0), + 0x10, + U8G_ESC_DLY(10), + 0x01, + U8G_ESC_DLY(100), U8G_ESC_DLY(100), + 0x36, U8G_ESC_ADR(1), 0xE8, + U8G_ESC_ADR(0), 0x3A, U8G_ESC_ADR(1), 0x55, + U8G_ESC_ADR(0), LCD_COLUMN, U8G_ESC_ADR(1), 0x00, 0x00, 0x01, 0x3F, + U8G_ESC_ADR(0), LCD_ROW, U8G_ESC_ADR(1), 0x00, 0x00, 0x00, 0xEF, + U8G_ESC_ADR(0), 0xC5, U8G_ESC_ADR(1), 0x3E, 0x28, + U8G_ESC_ADR(0), 0xC7, U8G_ESC_ADR(1), 0x86, + U8G_ESC_ADR(0), 0xB1, U8G_ESC_ADR(1), 0x00, 0x18, + U8G_ESC_ADR(0), 0xC0, U8G_ESC_ADR(1), 0x23, + U8G_ESC_ADR(0), 0xC1, U8G_ESC_ADR(1), 0x10, + U8G_ESC_ADR(0), 0x29, + U8G_ESC_ADR(0), 0x11, + U8G_ESC_DLY(100), + U8G_ESC_END +}; + +#if ENABLED(TOUCH_BUTTONS) + + static const uint8_t button0[] = { + B01111111,B11111111,B11111111,B11111111,B11111110, + B10000000,B00000000,B00000000,B00000000,B00000001, + B10000000,B00000000,B00000000,B00000000,B00000001, + B10000000,B00000000,B00010000,B00000000,B00000001, + B10000000,B00000000,B00010000,B00000000,B00000001, + B10000000,B01000000,B00010000,B00000000,B00000001, + B10000000,B11100000,B00010000,B00000000,B00000001, + B10000001,B11110000,B00010000,B00000000,B00000001, + B10000011,B11111000,B00010000,B00000000,B00000001, + B10000111,B11111100,B00010000,B11111111,B11100001, + B10000000,B11100000,B00010000,B11111111,B11100001, + B10000000,B11100000,B00010000,B00000000,B00000001, + B10000000,B11100000,B00010000,B00000000,B00000001, + B10000000,B11100000,B00010000,B00000000,B00000001, + B10000000,B11100000,B00010000,B00000000,B00000001, + B10000000,B00000000,B00010000,B00000000,B00000001, + B10000000,B00000000,B00010000,B00000000,B00000001, + B10000000,B00000000,B00000000,B00000000,B00000001, + B10000000,B00000000,B00000000,B00000000,B00000001, + B01111111,B11111111,B11111111,B11111111,B11111110, + }; + + static const uint8_t button1[] = { + B01111111,B11111111,B11111111,B11111111,B11111110, + B10000000,B00000000,B00000000,B00000000,B00000001, + B10000000,B00000000,B00000000,B00000000,B00000001, + B10000000,B00000000,B00010000,B00000000,B00000001, + B10000000,B00000000,B00010000,B00000110,B00000001, + B10000000,B11100000,B00010000,B00000110,B00000001, + B10000000,B11100000,B00010000,B00000110,B00000001, + B10000000,B11100000,B00010000,B00000110,B00000001, + B10000000,B11100000,B00010000,B00000110,B00000001, + B10000000,B11100000,B00010000,B11111111,B11110001, + B10000111,B11111100,B00010000,B11111111,B11110001, + B10000011,B11111000,B00010000,B00000110,B00000001, + B10000001,B11110000,B00010000,B00000110,B00000001, + B10000000,B11100000,B00010000,B00000110,B00000001, + B10000000,B01000000,B00010000,B00000110,B00000001, + B10000000,B00000000,B00010000,B00000110,B00000001, + B10000000,B00000000,B00010000,B00000000,B00000001, + B10000000,B00000000,B00000000,B00000000,B00000001, + B10000000,B00000000,B00000000,B00000000,B00000001, + B01111111,B11111111,B11111111,B11111111,B11111110, + }; + + static const uint8_t button2[] = { + B01111111,B11111111,B11111111,B11111111,B11111110, + B10000000,B00000000,B00000000,B00000000,B00000001, + B10000000,B00000000,B00000000,B00000000,B00000001, + B10000000,B00000000,B00000000,B00000000,B00000001, + B10000000,B00000000,B00000000,B00000000,B00000001, + B10000000,B00000000,B00000000,B00000000,B00000001, + B10000000,B00000000,B00000001,B11000000,B00000001, + B10000000,B00000000,B01000001,B11000000,B00000001, + B10000000,B00000000,B11000001,B11000000,B00000001, + B10000000,B00000001,B11111111,B11000000,B00000001, + B10000000,B00000011,B11111111,B11000000,B00000001, + B10000000,B00000001,B11111111,B11000000,B00000001, + B10000000,B00000000,B11000000,B00000000,B00000001, + B10000000,B00000000,B01000000,B00000000,B00000001, + B10000000,B00000000,B00000000,B00000000,B00000001, + B10000000,B00000000,B00000000,B00000000,B00000001, + B10000000,B00000000,B00000000,B00000000,B00000001, + B10000000,B00000000,B00000000,B00000000,B00000001, + B10000000,B00000000,B00000000,B00000000,B00000001, + B01111111,B11111111,B11111111,B11111111,B11111110, + }; + + void drawImage(const uint8_t *data, u8g_t *u8g, u8g_dev_t *dev, uint16_t length, uint16_t height, uint16_t color) { + uint16_t buffer[160]; + + for (uint16_t i = 0; i < height; i++) { + uint16_t k = 0; + for (uint16_t j = 0; j < length; j++) { + uint16_t v = TFT_MARLINBG_COLOR; + if (*(data + (i * (length >> 3) + (j >> 3))) & (0x80 >> (j & 7))) + v = color; + else + v = TFT_MARLINBG_COLOR; + buffer[k++] = v; buffer[k++] = v; + } + #ifdef LCD_USE_DMA_FSMC + if (k <= 80) { // generally is... for our buttons + memcpy(&buffer[k], &buffer[0], k * sizeof(uint16_t)); + LCD_IO_WriteSequence(buffer, k * sizeof(uint16_t)); + } + else { + LCD_IO_WriteSequence(buffer, k); + LCD_IO_WriteSequence(buffer, k); + } + #else + u8g_WriteSequence(u8g, dev, k << 1, (uint8_t *)buffer); + u8g_WriteSequence(u8g, dev, k << 1, (uint8_t *)buffer); + #endif + } + } + +#endif // TOUCH_BUTTONS + +// Used to fill RGB565 (16bits) background +inline void memset2(const void *ptr, uint16_t fill, size_t cnt) { + uint16_t* wptr = (uint16_t*) ptr; + for (size_t i = 0; i < cnt; i += 2) { + *wptr = fill; + wptr++; + } +} + +static bool preinit = true; +static uint8_t page; + uint8_t u8g_dev_tft_320x240_upscale_from_128x64_fn(u8g_t *u8g, u8g_dev_t *dev, uint8_t msg, void *arg) { u8g_pb_t *pb = (u8g_pb_t *)(dev->dev_mem); - uint16_t buffer[256]; - uint32_t i, j, k; - + #ifdef LCD_USE_DMA_FSMC + static uint16_t bufferA[512], bufferB[512]; + uint16_t* buffer = &bufferA[0]; + bool allow_async = true; + #else + uint16_t buffer[256]; // 16-bit RGB 565 pixel line buffer + #endif switch (msg) { case U8G_DEV_MSG_INIT: dev->com_fn(u8g, U8G_COM_MSG_INIT, U8G_SPI_CLK_CYCLE_NONE, &lcd_id); if (lcd_id == 0x040404) return 0; // No connected display on FSMC if (lcd_id == 0xFFFFFF) return 0; // No connected display on SPI - memset(buffer, 0x00, sizeof(buffer)); - if ((lcd_id & 0xFFFF) == 0x8552) // ST7789V u8g_WriteEscSeqP(u8g, dev, st7789v_init_sequence); + if ((lcd_id & 0xFFFF) == 0x9341) // ILI9341 + u8g_WriteEscSeqP(u8g, dev, ili9341_init_sequence); + + if (preinit) { + preinit = false; + return u8g_dev_pb8v1_base_fn(u8g, dev, msg, arg); + } u8g_WriteEscSeqP(u8g, dev, clear_screen_sequence); - for (i = 0; i < 960; i++) - u8g_WriteSequence(u8g, dev, 160, (uint8_t *)buffer); - break; + #ifdef LCD_USE_DMA_FSMC + LCD_IO_WriteMultiple(TFT_MARLINBG_COLOR, (320*240)); + #else + memset2(buffer, TFT_MARLINBG_COLOR, 160); + for (uint16_t i = 0; i < 960; i++) + u8g_WriteSequence(u8g, dev, 160, (uint8_t *)buffer); + #endif - case U8G_DEV_MSG_STOP: - break; + // bottom line and buttons + #if ENABLED(TOUCH_BUTTONS) + + #ifdef LCD_USE_DMA_FSMC + u8g_WriteEscSeqP(u8g, dev, separation_line_sequence_left); + LCD_IO_WriteMultiple(TFT_DISABLED_COLOR, 300); + u8g_WriteEscSeqP(u8g, dev, separation_line_sequence_right); + LCD_IO_WriteMultiple(TFT_DISABLED_COLOR, 300); + #else + memset2(buffer, TFT_DISABLED_COLOR, 150); + u8g_WriteEscSeqP(u8g, dev, separation_line_sequence_left); + for (uint8_t i = 4; i--;) + u8g_WriteSequence(u8g, dev, 150, (uint8_t *)buffer); + u8g_WriteEscSeqP(u8g, dev, separation_line_sequence_right); + for (uint8_t i = 4; i--;) + u8g_WriteSequence(u8g, dev, 150, (uint8_t *)buffer); + #endif + + u8g_WriteEscSeqP(u8g, dev, button0_sequence); + drawImage(button0, u8g, dev, 40, 20, TFT_BTSLEFT_COLOR); + + u8g_WriteEscSeqP(u8g, dev, button1_sequence); + drawImage(button1, u8g, dev, 40, 20, TFT_BTSLEFT_COLOR); + + u8g_WriteEscSeqP(u8g, dev, button2_sequence); + drawImage(button2, u8g, dev, 40, 20, TFT_BTRIGHT_COLOR); + + #endif // TOUCH_BUTTONS + + return 0; + + case U8G_DEV_MSG_STOP: preinit = true; break; case U8G_DEV_MSG_PAGE_FIRST: + page = 0; u8g_WriteEscSeqP(u8g, dev, page_first_sequence); break; case U8G_DEV_MSG_PAGE_NEXT: - for (j = 0; j < 8; j++) { - k = 0; - for (i = 0; i < (uint32_t)pb->width; i++) { + if (++page > 8) return 1; + + for (uint8_t y = 0; y < 8; y++) { + uint32_t k = 0; + #ifdef LCD_USE_DMA_FSMC + buffer = (y & 1) ? bufferB : bufferA; + #endif + for (uint16_t i = 0; i < (uint32_t)pb->width; i++) { const uint8_t b = *(((uint8_t *)pb->buf) + i); - const uint16_t c = TEST(b, j) ? 0x7FFF : 0x0000; + const uint16_t c = TEST(b, y) ? TFT_MARLINUI_COLOR : TFT_MARLINBG_COLOR; buffer[k++] = c; buffer[k++] = c; } - for (k = 0; k < 2; k++) { - u8g_WriteSequence(u8g, dev, 128, (uint8_t*)buffer); - u8g_WriteSequence(u8g, dev, 128, (uint8_t*)&(buffer[64])); - u8g_WriteSequence(u8g, dev, 128, (uint8_t*)&(buffer[128])); - u8g_WriteSequence(u8g, dev, 128, (uint8_t*)&(buffer[192])); - } + #ifdef LCD_USE_DMA_FSMC + memcpy(&buffer[256], &buffer[0], 512); + if (allow_async) { + if (y > 0 || page > 1) LCD_IO_WaitSequence_Async(); + if (y == 7 && page == 8) + LCD_IO_WriteSequence(buffer, 512); // last line of last page + else + LCD_IO_WriteSequence_Async(buffer, 512); + } + else + LCD_IO_WriteSequence(buffer, 512); + #else + for (uint8_t i = 2; i--;) { + u8g_WriteSequence(u8g, dev, 128, (uint8_t*)buffer); + u8g_WriteSequence(u8g, dev, 128, (uint8_t*)&(buffer[64])); + u8g_WriteSequence(u8g, dev, 128, (uint8_t*)&(buffer[128])); + u8g_WriteSequence(u8g, dev, 128, (uint8_t*)&(buffer[192])); + } + #endif } break; case U8G_DEV_MSG_SLEEP_ON: + // Enter Sleep Mode (10h) + return 1; case U8G_DEV_MSG_SLEEP_OFF: + // Sleep Out (11h) return 1; } return u8g_dev_pb8v1_base_fn(u8g, dev, msg, arg); @@ -174,4 +444,4 @@ uint8_t u8g_dev_tft_320x240_upscale_from_128x64_fn(u8g_t *u8g, u8g_dev_t *dev, u U8G_PB_DEV(u8g_dev_tft_320x240_upscale_from_128x64, WIDTH, HEIGHT, PAGE_HEIGHT, u8g_dev_tft_320x240_upscale_from_128x64_fn, U8G_COM_HAL_FSMC_FN); -#endif // HAS_GRAPHICAL_LCD +#endif // HAS_GRAPHICAL_LCD && FSMC_CS diff --git a/Marlin/src/lcd/dogm/ultralcd_DOGM.cpp b/Marlin/src/lcd/dogm/ultralcd_DOGM.cpp index 47cb7ca1a1..023ad66aca 100644 --- a/Marlin/src/lcd/dogm/ultralcd_DOGM.cpp +++ b/Marlin/src/lcd/dogm/ultralcd_DOGM.cpp @@ -105,56 +105,63 @@ void MarlinUI::set_font(const MarlinFont font_nr) { #if ENABLED(SHOW_BOOTSCREEN) #if ENABLED(SHOW_CUSTOM_BOOTSCREEN) - - FORCE_INLINE void draw_custom_bootscreen(const u8g_pgm_uint8_t * const bmp, const bool erase=true) { - constexpr u8g_uint_t left = (LCD_PIXEL_WIDTH - (CUSTOM_BOOTSCREEN_BMPWIDTH)) / 2, - top = (LCD_PIXEL_HEIGHT - (CUSTOM_BOOTSCREEN_BMPHEIGHT)) / 2; + // Draws a slice of a particular frame of the custom bootscreen, without the u8g loop + void MarlinUI::draw_custom_bootscreen(const uint8_t frame/*=0*/) { + constexpr u8g_uint_t left = u8g_uint_t((LCD_PIXEL_WIDTH - (CUSTOM_BOOTSCREEN_BMPWIDTH)) / 2), + top = u8g_uint_t((LCD_PIXEL_HEIGHT - (CUSTOM_BOOTSCREEN_BMPHEIGHT)) / 2); #if ENABLED(CUSTOM_BOOTSCREEN_INVERTED) constexpr u8g_uint_t right = left + CUSTOM_BOOTSCREEN_BMPWIDTH, bottom = top + CUSTOM_BOOTSCREEN_BMPHEIGHT; #endif - u8g.firstPage(); - do { - u8g.drawBitmapP( - left, top, - CEILING(CUSTOM_BOOTSCREEN_BMPWIDTH, 8), CUSTOM_BOOTSCREEN_BMPHEIGHT, bmp - ); - #if ENABLED(CUSTOM_BOOTSCREEN_INVERTED) - if (erase) { - u8g.setColorIndex(1); - if (top) u8g.drawBox(0, 0, LCD_PIXEL_WIDTH, top); - if (left) u8g.drawBox(0, top, left, CUSTOM_BOOTSCREEN_BMPHEIGHT); - if (right < LCD_PIXEL_WIDTH) u8g.drawBox(right, top, LCD_PIXEL_WIDTH - right, CUSTOM_BOOTSCREEN_BMPHEIGHT); - if (bottom < LCD_PIXEL_HEIGHT) u8g.drawBox(0, bottom, LCD_PIXEL_WIDTH, LCD_PIXEL_HEIGHT - bottom); - } + + const u8g_pgm_uint8_t * const bmp = + #if ENABLED(ANIMATED_BOOTSCREEN) + (u8g_pgm_uint8_t*)pgm_read_ptr(&custom_bootscreen_animation[frame]) #else - UNUSED(erase); + custom_start_bmp #endif - } while (u8g.nextPage()); + ; + + u8g.drawBitmapP( + left, top, + CEILING(CUSTOM_BOOTSCREEN_BMPWIDTH, 8), CUSTOM_BOOTSCREEN_BMPHEIGHT, bmp + ); + + #if ENABLED(CUSTOM_BOOTSCREEN_INVERTED) + if (frame == 0) { + u8g.setColorIndex(1); + if (top) u8g.drawBox(0, 0, LCD_PIXEL_WIDTH, top); + if (left) u8g.drawBox(0, top, left, CUSTOM_BOOTSCREEN_BMPHEIGHT); + if (right < LCD_PIXEL_WIDTH) u8g.drawBox(right, top, LCD_PIXEL_WIDTH - right, CUSTOM_BOOTSCREEN_BMPHEIGHT); + if (bottom < LCD_PIXEL_HEIGHT) u8g.drawBox(0, bottom, LCD_PIXEL_WIDTH, LCD_PIXEL_HEIGHT - bottom); + } + #endif } - void lcd_custom_bootscreen() { - #if ENABLED(ANIMATED_BOOTSCREEN) - LOOP_L_N(f, COUNT(custom_bootscreen_animation)) { - if (f) safe_delay(CUSTOM_BOOTSCREEN_FRAME_TIME); - draw_custom_bootscreen((u8g_pgm_uint8_t*)pgm_read_ptr(&custom_bootscreen_animation[f]), f == 0); - } + // Shows the custom bootscreen, with the u8g loop, animations and delays + void MarlinUI::show_custom_bootscreen() { + #if DISABLED(ANIMATED_BOOTSCREEN) + constexpr millis_t d = 0; + constexpr uint8_t f = 0; #else - draw_custom_bootscreen(custom_start_bmp); + constexpr millis_t d = CUSTOM_BOOTSCREEN_FRAME_TIME; + LOOP_L_N(f, COUNT(custom_bootscreen_animation)) #endif + { + u8g.firstPage(); + do { draw_custom_bootscreen(f); } while (u8g.nextPage()); + if (d) safe_delay(d); + } + #ifndef CUSTOM_BOOTSCREEN_TIMEOUT #define CUSTOM_BOOTSCREEN_TIMEOUT 2500 #endif safe_delay(CUSTOM_BOOTSCREEN_TIMEOUT); } - #endif // SHOW_CUSTOM_BOOTSCREEN - void MarlinUI::show_bootscreen() { - #if ENABLED(SHOW_CUSTOM_BOOTSCREEN) - lcd_custom_bootscreen(); - #endif - + // Draws a slice of the Marlin bootscreen, without the u8g loop + void MarlinUI::draw_marlin_bootscreen() { // Screen dimensions. //const uint8_t width = u8g.getWidth(), height = u8g.getHeight(); constexpr uint8_t width = LCD_PIXEL_WIDTH, height = LCD_PIXEL_HEIGHT; @@ -162,14 +169,14 @@ void MarlinUI::set_font(const MarlinFont font_nr) { // Determine text space needed #ifndef STRING_SPLASH_LINE2 constexpr uint8_t text_total_height = MENU_FONT_HEIGHT, - text_width_1 = (sizeof(STRING_SPLASH_LINE1) - 1) * (MENU_FONT_WIDTH), + text_width_1 = uint8_t(sizeof(STRING_SPLASH_LINE1) - 1) * uint8_t(MENU_FONT_WIDTH), text_width_2 = 0; #else - constexpr uint8_t text_total_height = (MENU_FONT_HEIGHT) * 2, - text_width_1 = (sizeof(STRING_SPLASH_LINE1) - 1) * (MENU_FONT_WIDTH), - text_width_2 = (sizeof(STRING_SPLASH_LINE2) - 1) * (MENU_FONT_WIDTH); + constexpr uint8_t text_total_height = uint8_t(MENU_FONT_HEIGHT) * 2, + text_width_1 = uint8_t(sizeof(STRING_SPLASH_LINE1) - 1) * uint8_t(MENU_FONT_WIDTH), + text_width_2 = uint8_t(sizeof(STRING_SPLASH_LINE2) - 1) * uint8_t(MENU_FONT_WIDTH); #endif - constexpr uint8_t text_max_width = MAX(text_width_1, text_width_2), + constexpr uint8_t text_max_width = _MAX(text_width_1, text_width_2), rspace = width - (START_BMPWIDTH); int8_t offx, offy, txt_base, txt_offx_1, txt_offx_2; @@ -193,23 +200,33 @@ void MarlinUI::set_font(const MarlinFont font_nr) { NOLESS(offx, 0); NOLESS(offy, 0); - u8g.firstPage(); - do { - u8g.drawBitmapP(offx, offy, (START_BMPWIDTH + 7) / 8, START_BMPHEIGHT, start_bmp); - set_font(FONT_MENU); - #ifndef STRING_SPLASH_LINE2 - u8g.drawStr(txt_offx_1, txt_base, STRING_SPLASH_LINE1); - #else - u8g.drawStr(txt_offx_1, txt_base - (MENU_FONT_HEIGHT), STRING_SPLASH_LINE1); - u8g.drawStr(txt_offx_2, txt_base, STRING_SPLASH_LINE2); - #endif - } while (u8g.nextPage()); + u8g.drawBitmapP(offx, offy, (START_BMPWIDTH + 7) / 8, START_BMPHEIGHT, start_bmp); + set_font(FONT_MENU); + #ifndef STRING_SPLASH_LINE2 + u8g.drawStr(txt_offx_1, txt_base, STRING_SPLASH_LINE1); + #else + u8g.drawStr(txt_offx_1, txt_base - (MENU_FONT_HEIGHT), STRING_SPLASH_LINE1); + u8g.drawStr(txt_offx_2, txt_base, STRING_SPLASH_LINE2); + #endif + } + + // Shows the Marlin bootscreen, with the u8g loop and delays + void MarlinUI::show_marlin_bootscreen() { #ifndef BOOTSCREEN_TIMEOUT #define BOOTSCREEN_TIMEOUT 2500 #endif + u8g.firstPage(); + do { draw_marlin_bootscreen(); } while (u8g.nextPage()); safe_delay(BOOTSCREEN_TIMEOUT); } + void MarlinUI::show_bootscreen() { + #if ENABLED(SHOW_CUSTOM_BOOTSCREEN) + show_custom_bootscreen(); + #endif + show_marlin_bootscreen(); + } + #endif // SHOW_BOOTSCREEN #if ENABLED(LIGHTWEIGHT_UI) @@ -219,26 +236,34 @@ void MarlinUI::set_font(const MarlinFont font_nr) { // Initialize or re-initialize the LCD void MarlinUI::init_lcd() { - #if PIN_EXISTS(LCD_BACKLIGHT) // Enable LCD backlight - OUT_WRITE(LCD_BACKLIGHT_PIN, HIGH); + #if PIN_EXISTS(LCD_BACKLIGHT) + OUT_WRITE(LCD_BACKLIGHT_PIN, ( + #if ENABLED(DELAYED_BACKLIGHT_INIT) + LOW // Illuminate after reset + #else + HIGH // Illuminate right away + #endif + )); #endif #if EITHER(MKS_12864OLED, MKS_12864OLED_SSD1306) SET_OUTPUT(LCD_PINS_DC); - #if !defined(LCD_RESET_PIN) + #ifndef LCD_RESET_PIN #define LCD_RESET_PIN LCD_PINS_RS #endif #endif #if PIN_EXISTS(LCD_RESET) - OUT_WRITE(LCD_RESET_PIN, LOW); // perform a clean hardware reset + // Perform a clean hardware reset with needed delays + OUT_WRITE(LCD_RESET_PIN, LOW); _delay_ms(5); - OUT_WRITE(LCD_RESET_PIN, HIGH); - _delay_ms(5); // delay to allow the display to initialize + WRITE(LCD_RESET_PIN, HIGH); + _delay_ms(5); + u8g.begin(); #endif - #if PIN_EXISTS(LCD_RESET) - u8g.begin(); + #if PIN_EXISTS(LCD_BACKLIGHT) && ENABLED(DELAYED_BACKLIGHT_INIT) + WRITE(LCD_BACKLIGHT_PIN, HIGH); #endif #if HAS_LCD_CONTRAST @@ -246,11 +271,11 @@ void MarlinUI::init_lcd() { #endif #if ENABLED(LCD_SCREEN_ROT_90) - u8g.setRot90(); // Rotate screen by 90° + u8g.setRot90(); #elif ENABLED(LCD_SCREEN_ROT_180) - u8g.setRot180(); // Rotate screen by 180° + u8g.setRot180(); #elif ENABLED(LCD_SCREEN_ROT_270) - u8g.setRot270(); // Rotate screen by 270° + u8g.setRot270(); #endif uxg_SetUtf8Fonts(g_fontinfo, COUNT(g_fontinfo)); @@ -375,8 +400,9 @@ void MarlinUI::clear_lcd() { } // Automatically cleared by Picture Loop } void draw_edit_screen(PGM_P const pstr, const char* const value/*=nullptr*/) { - const uint8_t labellen = utf8_strlen_P(pstr), vallen = utf8_strlen(value); + ui.encoder_direction_normal(); + const uint8_t labellen = utf8_strlen_P(pstr), vallen = utf8_strlen(value); bool extra_row = labellen > LCD_WIDTH - 2 - vallen; #if ENABLED(USE_BIG_EDIT_FONT) diff --git a/Marlin/src/lcd/dogm/ultralcd_DOGM.h b/Marlin/src/lcd/dogm/ultralcd_DOGM.h index 409b2b3062..4d9662d7db 100644 --- a/Marlin/src/lcd/dogm/ultralcd_DOGM.h +++ b/Marlin/src/lcd/dogm/ultralcd_DOGM.h @@ -126,7 +126,7 @@ // Connected via motherboard header #define U8G_CLASS U8GLIB_SH1106_128X64 #define U8G_PARAM DOGLCD_SCK, DOGLCD_MOSI, DOGLCD_CS, LCD_PINS_DC, LCD_PINS_RS -#elif ENABLED(MKS_ROBIN_TFT) +#elif ENABLED(FSMC_GRAPHICAL_TFT) // Unspecified 320x240 TFT pre-initialized by built-in bootloader #define U8G_CLASS U8GLIB_TFT_320X240_UPSCALE_FROM_128X64 #define U8G_PARAM FSMC_CS_PIN, FSMC_RS_PIN diff --git a/Marlin/src/lcd/dogm/ultralcd_st7920_u8glib_rrd_AVR.cpp b/Marlin/src/lcd/dogm/ultralcd_st7920_u8glib_rrd_AVR.cpp index ae92e861a1..bc808b2a35 100644 --- a/Marlin/src/lcd/dogm/ultralcd_st7920_u8glib_rrd_AVR.cpp +++ b/Marlin/src/lcd/dogm/ultralcd_st7920_u8glib_rrd_AVR.cpp @@ -42,11 +42,17 @@ // Optimize this code with -O3 #pragma GCC optimize (3) -#define ST7920_SND_BIT \ - WRITE(ST7920_CLK_PIN, LOW); ST7920_DELAY_1; \ - WRITE(ST7920_DAT_PIN, val & 0x80); ST7920_DELAY_2; \ - WRITE(ST7920_CLK_PIN, HIGH); ST7920_DELAY_3; \ - val <<= 1 + +#ifdef ARDUINO_ARCH_STM32F1 + #define ST7920_DAT(V) !!((V) & 0x80) +#else + #define ST7920_DAT(V) ((V) & 0x80) +#endif +#define ST7920_SND_BIT do{ \ + WRITE(ST7920_CLK_PIN, LOW); ST7920_DELAY_1; \ + WRITE(ST7920_DAT_PIN, ST7920_DAT(val)); ST7920_DELAY_2; \ + WRITE(ST7920_CLK_PIN, HIGH); ST7920_DELAY_3; \ + val <<= 1; }while(0) // Optimize this code with -O3 #pragma GCC optimize (3) diff --git a/Marlin/src/lcd/extensible_ui/lib/dgus/DGUSDisplay.cpp b/Marlin/src/lcd/extensible_ui/lib/dgus/DGUSDisplay.cpp index b3aba94d38..60a534a307 100644 --- a/Marlin/src/lcd/extensible_ui/lib/dgus/DGUSDisplay.cpp +++ b/Marlin/src/lcd/extensible_ui/lib/dgus/DGUSDisplay.cpp @@ -343,7 +343,7 @@ void DGUSScreenVariableHandler::DGUSLCD_SendStringToDisplayPGM(DGUS_VP_Variable } void DGUSScreenVariableHandler::DGUSLCD_SD_StartPrint(DGUS_VP_Variable &var, void *val_ptr) { - if(!filelist.seek(file_to_print)) return; + if (!filelist.seek(file_to_print)) return; ExtUI::printFile(filelist.filename()); ScreenHandler.GotoScreen(DGUSLCD_SCREEN_STATUS); } diff --git a/Marlin/src/lcd/extensible_ui/ui_api.cpp b/Marlin/src/lcd/extensible_ui/ui_api.cpp index d4eb9617fb..014c8da5e5 100644 --- a/Marlin/src/lcd/extensible_ui/ui_api.cpp +++ b/Marlin/src/lcd/extensible_ui/ui_api.cpp @@ -98,8 +98,12 @@ #include "../../feature/babystep.h" #endif +#if ENABLED(HOST_PROMPT_SUPPORT) + #include "../../feature/host_actions.h" +#endif + inline float clamp(const float value, const float minimum, const float maximum) { - return MAX(MIN(value, maximum), minimum); + return _MAX(_MIN(value, maximum), minimum); } static struct { @@ -668,9 +672,11 @@ namespace ExtUI { && (linked_nozzles || active_extruder == 0) #endif ) zprobe_zoffset += mm; + #else + UNUSED(mm); #endif - #if EXTRUDERS > 1 + #if EXTRUDERS > 1 && HAS_HOTEND_OFFSET /** * When linked_nozzles is false, as an axis is babystepped * adjust the hotend offsets so that the other nozzles are @@ -687,6 +693,7 @@ namespace ExtUI { } #else UNUSED(linked_nozzles); + UNUSED(mm); #endif } diff --git a/Marlin/src/lcd/extensible_ui/ui_api.h b/Marlin/src/lcd/extensible_ui/ui_api.h index 6cffefe510..5cae33a287 100644 --- a/Marlin/src/lcd/extensible_ui/ui_api.h +++ b/Marlin/src/lcd/extensible_ui/ui_api.h @@ -42,8 +42,6 @@ * location: . * ****************************************************************************/ -#pragma once - #include "../../inc/MarlinConfig.h" namespace ExtUI { diff --git a/Marlin/src/lcd/extui_example.cpp b/Marlin/src/lcd/extui_example.cpp index 1bcfea60d0..4fec2745a9 100644 --- a/Marlin/src/lcd/extui_example.cpp +++ b/Marlin/src/lcd/extui_example.cpp @@ -54,7 +54,7 @@ namespace ExtUI { void onPrintTimerStarted() {} void onPrintTimerPaused() {} void onPrintTimerStopped() {} - void onFilamentRunout() {} + void onFilamentRunout(const extruder_t extruder) {} void onUserConfirmRequired(const char * const msg) {} void onStatusChanged(const char * const msg) {} void onFactoryReset() {} diff --git a/Marlin/src/lcd/extui_malyan_lcd.cpp b/Marlin/src/lcd/extui_malyan_lcd.cpp index 7c9265093c..dde1a4c8ff 100644 --- a/Marlin/src/lcd/extui_malyan_lcd.cpp +++ b/Marlin/src/lcd/extui_malyan_lcd.cpp @@ -80,7 +80,7 @@ bool last_printing_status = false; // Everything written needs the high bit set. void write_to_lcd_P(PGM_P const message) { char encoded_message[MAX_CURLY_COMMAND]; - uint8_t message_length = MIN(strlen_P(message), sizeof(encoded_message)); + uint8_t message_length = _MIN(strlen_P(message), sizeof(encoded_message)); for (uint8_t i = 0; i < message_length; i++) encoded_message[i] = pgm_read_byte(&message[i]) | 0x80; @@ -90,7 +90,7 @@ void write_to_lcd_P(PGM_P const message) { void write_to_lcd(const char * const message) { char encoded_message[MAX_CURLY_COMMAND]; - const uint8_t message_length = MIN(strlen(message), sizeof(encoded_message)); + const uint8_t message_length = _MIN(strlen(message), sizeof(encoded_message)); for (uint8_t i = 0; i < message_length; i++) encoded_message[i] = message[i] | 0x80; @@ -114,21 +114,18 @@ void write_to_lcd(const char * const message) { void process_lcd_c_command(const char* command) { switch (command[0]) { case 'C': // Cope with both V1 early rev and later LCDs. - case 'S': { - int raw_feedrate = atoi(command + 1); - feedrate_percentage = raw_feedrate * 10; - feedrate_percentage = constrain(feedrate_percentage, 10, 999); - } break; - case 'T': { - thermalManager.setTargetHotend(atoi(command + 1), 0); - } break; - case 'P': { - thermalManager.setTargetBed(atoi(command + 1)); - } break; + case 'S': + feedrate_percentage = atoi(command + 1) * 10; + LIMIT(feedrate_percentage, 10, 999); + break; - default: - SERIAL_ECHOLNPAIR("UNKNOWN C COMMAND", command); - return; + case 'T': thermalManager.setTargetHotend(atoi(command + 1), 0); break; + + #if HAS_HEATED_BED + case 'P': thermalManager.setTargetBed(atoi(command + 1)); break; + #endif + + default: SERIAL_ECHOLNPAIR("UNKNOWN C COMMAND", command); } } @@ -149,21 +146,20 @@ void process_lcd_eb_command(const char* command) { char message_buffer[MAX_CURLY_COMMAND]; sprintf_P(message_buffer, - PSTR("{T0:%03.0f/%03i}{T1:000/000}{TP:%03.0f/%03i}{TQ:%03i}{TT:%s}"), - thermalManager.degHotend(0), - thermalManager.degTargetHotend(0), - #if HAS_HEATED_BED - thermalManager.degBed(), - thermalManager.degTargetBed(), - #else - 0, 0, - #endif - #if ENABLED(SDSUPPORT) - card.percentDone(), - #else - 0, - #endif - elapsed_buffer); + PSTR("{T0:%03.0f/%03i}{T1:000/000}{TP:%03.0f/%03i}{TQ:%03i}{TT:%s}"), + thermalManager.degHotend(0), thermalManager.degTargetHotend(0), + #if HAS_HEATED_BED + thermalManager.degBed(), thermalManager.degTargetBed(), + #else + 0, 0, + #endif + #if ENABLED(SDSUPPORT) + card.percentDone(), + #else + 0, + #endif + elapsed_buffer + ); write_to_lcd(message_buffer); } break; diff --git a/Marlin/src/lcd/fontutils.cpp b/Marlin/src/lcd/fontutils.cpp index 4e714d0804..fdccd082c3 100644 --- a/Marlin/src/lcd/fontutils.cpp +++ b/Marlin/src/lcd/fontutils.cpp @@ -9,7 +9,7 @@ #include "../inc/MarlinConfig.h" -#if ENABLED(ULTRA_LCD) +#if HAS_SPI_LCD #include "ultralcd.h" #include "../Marlin.h" #endif diff --git a/Marlin/src/lcd/language/language_an.h b/Marlin/src/lcd/language/language_an.h index 388e80341c..3ae5d967cc 100644 --- a/Marlin/src/lcd/language/language_an.h +++ b/Marlin/src/lcd/language/language_an.h @@ -72,7 +72,7 @@ #define MSG_MOVE_Y _UxGT("Mover Y") #define MSG_MOVE_Z _UxGT("Mover Z") #define MSG_MOVE_E _UxGT("Extrusor") -#define MSG_MOVE_0025MM _UxGT("Mover 0.025mm") +#define MSG_MOVE_Z_DIST _UxGT("Mover %smm") #define MSG_MOVE_01MM _UxGT("Mover 0.1mm") #define MSG_MOVE_1MM _UxGT("Mover 1mm") #define MSG_MOVE_10MM _UxGT("Mover 10mm") diff --git a/Marlin/src/lcd/language/language_bg.h b/Marlin/src/lcd/language/language_bg.h index eaf8e279bb..90afab43f5 100644 --- a/Marlin/src/lcd/language/language_bg.h +++ b/Marlin/src/lcd/language/language_bg.h @@ -62,7 +62,7 @@ #define MSG_MOVE_Y _UxGT("Движение по Y") #define MSG_MOVE_Z _UxGT("Движение по Z") #define MSG_MOVE_E _UxGT("Екструдер") -#define MSG_MOVE_0025MM _UxGT("Премести с 0.025mm") +#define MSG_MOVE_Z_DIST _UxGT("Премести с %smm") #define MSG_MOVE_01MM _UxGT("Премести с 0.1mm") #define MSG_MOVE_1MM _UxGT("Премести с 1mm") #define MSG_MOVE_10MM _UxGT("Премести с 10mm") diff --git a/Marlin/src/lcd/language/language_ca.h b/Marlin/src/lcd/language/language_ca.h index 7bbde2fc58..808566f583 100644 --- a/Marlin/src/lcd/language/language_ca.h +++ b/Marlin/src/lcd/language/language_ca.h @@ -76,7 +76,7 @@ #define MSG_MOVE_Y _UxGT("Mou Y") #define MSG_MOVE_Z _UxGT("Mou Z") #define MSG_MOVE_E _UxGT("Extrusor") -#define MSG_MOVE_0025MM _UxGT("Mou 0.025mm") +#define MSG_MOVE_Z_DIST _UxGT("Mou %smm") #define MSG_MOVE_01MM _UxGT("Mou 0.1mm") #define MSG_MOVE_1MM _UxGT("Mou 1mm") #define MSG_MOVE_10MM _UxGT("Mou 10mm") diff --git a/Marlin/src/lcd/language/language_cz.h b/Marlin/src/lcd/language/language_cz.h index e5b73acff7..7310ca4b11 100644 --- a/Marlin/src/lcd/language/language_cz.h +++ b/Marlin/src/lcd/language/language_cz.h @@ -202,7 +202,7 @@ #define MSG_MOVE_Z _UxGT("Posunout Z") #define MSG_MOVE_E _UxGT("Extrudér") #define MSG_HOTEND_TOO_COLD _UxGT("Hotend je studený") -#define MSG_MOVE_0025MM _UxGT("Posunout o 0,025mm") +#define MSG_MOVE_Z_DIST _UxGT("Posunout o %smm") #define MSG_MOVE_01MM _UxGT("Posunout o 0,1mm") #define MSG_MOVE_1MM _UxGT("Posunout o 1mm") #define MSG_MOVE_10MM _UxGT("Posunout o 10mm") diff --git a/Marlin/src/lcd/language/language_da.h b/Marlin/src/lcd/language/language_da.h index 2c3f14152d..b65e5621dd 100644 --- a/Marlin/src/lcd/language/language_da.h +++ b/Marlin/src/lcd/language/language_da.h @@ -72,7 +72,7 @@ #define MSG_MOVE_Y _UxGT("Flyt Y") #define MSG_MOVE_Z _UxGT("Flyt Z") #define MSG_MOVE_E _UxGT("Extruder") -#define MSG_MOVE_0025MM _UxGT("Flyt 0.025mm") +#define MSG_MOVE_Z_DIST _UxGT("Flyt %smm") #define MSG_MOVE_01MM _UxGT("Flyt 0.1mm") #define MSG_MOVE_1MM _UxGT("Flyt 1mm") #define MSG_MOVE_10MM _UxGT("Flyt 10mm") diff --git a/Marlin/src/lcd/language/language_de.h b/Marlin/src/lcd/language/language_de.h index a1ada61c78..d78c8d60f1 100644 --- a/Marlin/src/lcd/language/language_de.h +++ b/Marlin/src/lcd/language/language_de.h @@ -41,12 +41,12 @@ #define MSG_SD_REMOVED _UxGT("SD-Karte entfernt") #define MSG_SD_RELEASED _UxGT("SD-Karte freigeg.") #define MSG_LCD_ENDSTOPS _UxGT("Endstopp") // Max length 8 characters -#define MSG_LCD_SOFT_ENDSTOPS _UxGT("Soft-Endstopp") +#define MSG_LCD_SOFT_ENDSTOPS _UxGT("Software-Endstopp") #define MSG_MAIN _UxGT("Hauptmenü") #define MSG_ADVANCED_SETTINGS _UxGT("Erw. Einstellungen") #define MSG_CONFIGURATION _UxGT("Konfiguration") #define MSG_AUTOSTART _UxGT("Autostart") -#define MSG_DISABLE_STEPPERS _UxGT("Motoren deaktivieren") // M84 +#define MSG_DISABLE_STEPPERS _UxGT("Motoren deaktivieren") // M84 :: Max length 19 characters #define MSG_DEBUG_MENU _UxGT("Debug-Menü") #define MSG_PROGRESS_BAR_TEST _UxGT("Statusbalken-Test") #define MSG_AUTO_HOME _UxGT("Home XYZ") // G28 @@ -62,18 +62,18 @@ #define MSG_SET_HOME_OFFSETS _UxGT("Setze Homeversatz") #define MSG_HOME_OFFSETS_APPLIED _UxGT("Homeversatz aktiv") #define MSG_SET_ORIGIN _UxGT("Setze Nullpunkte") //"G92 X0 Y0 Z0" commented out in ultralcd.cpp -#define MSG_PREHEAT_1 _UxGT("Vorwärmen " PREHEAT_1_LABEL) -#define MSG_PREHEAT_1_N _UxGT("Vorwärmen " PREHEAT_1_LABEL " ") -#define MSG_PREHEAT_1_ALL _UxGT("Vorw. " PREHEAT_1_LABEL " Alles") -#define MSG_PREHEAT_1_END _UxGT("Vorw. " PREHEAT_1_LABEL " Extr.") -#define MSG_PREHEAT_1_BEDONLY _UxGT("Vorw. " PREHEAT_1_LABEL " Bett") -#define MSG_PREHEAT_1_SETTINGS _UxGT("Vorw. " PREHEAT_1_LABEL " Einst.") -#define MSG_PREHEAT_2 _UxGT("Vorwärmen " PREHEAT_2_LABEL) -#define MSG_PREHEAT_2_N _UxGT("Vorwärmen " PREHEAT_2_LABEL " ") -#define MSG_PREHEAT_2_ALL _UxGT("Vorw. " PREHEAT_2_LABEL " Alles") -#define MSG_PREHEAT_2_END _UxGT("Vorw. " PREHEAT_2_LABEL " Extr.") -#define MSG_PREHEAT_2_BEDONLY _UxGT("Vorw. " PREHEAT_2_LABEL " Bett") -#define MSG_PREHEAT_2_SETTINGS _UxGT("Vorw. " PREHEAT_2_LABEL " Einst.") +#define MSG_PREHEAT_1 _UxGT(PREHEAT_1_LABEL " Vorwärmen") +#define MSG_PREHEAT_1_N _UxGT(PREHEAT_1_LABEL " Vorwärmen ") +#define MSG_PREHEAT_1_ALL _UxGT(PREHEAT_1_LABEL " Alles Vorwärmen") +#define MSG_PREHEAT_1_END _UxGT(PREHEAT_1_LABEL " Extr. Vorwärmen") +#define MSG_PREHEAT_1_BEDONLY _UxGT(PREHEAT_1_LABEL " Bett Vorwärmen") +#define MSG_PREHEAT_1_SETTINGS _UxGT(PREHEAT_1_LABEL " Einstellungen") +#define MSG_PREHEAT_2 _UxGT(PREHEAT_2_LABEL " Vorwärmen") +#define MSG_PREHEAT_2_N _UxGT(PREHEAT_2_LABEL " Vorwärmen ") +#define MSG_PREHEAT_2_ALL _UxGT(PREHEAT_2_LABEL " Alles Vorwärmen") +#define MSG_PREHEAT_2_END _UxGT(PREHEAT_2_LABEL " Extr. Vorwärmen") +#define MSG_PREHEAT_2_BEDONLY _UxGT(PREHEAT_2_LABEL " Bett Vorwärmen") +#define MSG_PREHEAT_2_SETTINGS _UxGT(PREHEAT_2_LABEL " Einstellungen") #define MSG_PREHEAT_CUSTOM _UxGT("benutzerdef. Heizen") #define MSG_COOLDOWN _UxGT("Abkühlen") #define MSG_LASER_MENU _UxGT("Laser") @@ -81,20 +81,21 @@ #define MSG_LASER_ON _UxGT("Laser an") #define MSG_LASER_POWER _UxGT("Laserleistung") #define MSG_SPINDLE_MENU _UxGT("Spindel-Steuerung") -#define MSG_SPINDLE_OFF _UxGT("Spindel Aus") -#define MSG_SPINDLE_ON _UxGT("Spindel An") +#define MSG_SPINDLE_OFF _UxGT("Spindel aus") +#define MSG_SPINDLE_ON _UxGT("Spindel an") #define MSG_SPINDLE_POWER _UxGT("Spindelleistung") #define MSG_SPINDLE_REVERSE _UxGT("Spindelrichtung") #define MSG_SWITCH_PS_ON _UxGT("Netzteil ein") #define MSG_SWITCH_PS_OFF _UxGT("Netzteil aus") #define MSG_EXTRUDE _UxGT("Extrudieren") #define MSG_RETRACT _UxGT("Einzug") -#define MSG_MOVE_AXIS _UxGT("Achse Bewegen") +#define MSG_MOVE_AXIS _UxGT("Achsen bewegen") #define MSG_BED_LEVELING _UxGT("Bett-Nivellierung") #define MSG_LEVEL_BED _UxGT("Bett nivellieren") #define MSG_LEVEL_CORNERS _UxGT("Ecken nivellieren") #define MSG_NEXT_CORNER _UxGT("Nächste Ecke") #define MSG_EDITING_STOPPED _UxGT("Netzbearb. angeh.") +#define MSG_PROBING_MESH _UxGT("Messpunkt") #define MSG_MESH_X _UxGT("Index X") #define MSG_MESH_Y _UxGT("Index Y") #define MSG_MESH_EDIT_Z _UxGT("Z-Wert") @@ -103,11 +104,12 @@ #define MSG_UBL_UNHOMED _UxGT("Home XYZ zuerst") #define MSG_UBL_TOOLS _UxGT("UBL-Werkzeuge") #define MSG_UBL_LEVEL_BED _UxGT("Unified Bed Leveling") -#define MSG_LCD_PROBING_MESH _UxGT("Messpunkt") #define MSG_LCD_TILTING_MESH _UxGT("Berührungspunkt") +#define MSG_M48_TEST _UxGT("M48 Sondentest") +#define MSG_M48_DEVIATION _UxGT("Abweichung") #define MSG_IDEX_MENU _UxGT("IDEX-Modus") #define MSG_OFFSETS_MENU _UxGT("Werkzeugversätze") -#define MSG_IDEX_MODE_AUTOPARK _UxGT("Autom. Parken") +#define MSG_IDEX_MODE_AUTOPARK _UxGT("Autom. parken") #define MSG_IDEX_MODE_DUPLICATE _UxGT("Duplizieren") #define MSG_IDEX_MODE_MIRRORED_COPY _UxGT("Spiegelkopie") #define MSG_IDEX_MODE_FULL_CTRL _UxGT("vollstä. Kontrolle") @@ -131,14 +133,14 @@ #define MSG_UBL_DONE_EDITING_MESH _UxGT("Bearbeitung beendet") #define MSG_UBL_BUILD_CUSTOM_MESH _UxGT("Eigenes Netz erst.") #define MSG_UBL_BUILD_MESH_MENU _UxGT("Netz erstellen") -#define MSG_UBL_BUILD_MESH_M1 _UxGT("Netz erstellen " PREHEAT_1_LABEL) -#define MSG_UBL_BUILD_MESH_M2 _UxGT("Netz erstellen " PREHEAT_2_LABEL) +#define MSG_UBL_BUILD_MESH_M1 _UxGT(PREHEAT_1_LABEL " Netz erstellen") +#define MSG_UBL_BUILD_MESH_M2 _UxGT(PREHEAT_2_LABEL " Netz erstellen") #define MSG_UBL_BUILD_COLD_MESH _UxGT("Netz erstellen kalt") #define MSG_UBL_MESH_HEIGHT_ADJUST _UxGT("Netzhöhe einst.") #define MSG_UBL_MESH_HEIGHT_AMOUNT _UxGT("Höhe") #define MSG_UBL_VALIDATE_MESH_MENU _UxGT("Netz validieren") -#define MSG_UBL_VALIDATE_MESH_M1 _UxGT("Netz validieren " PREHEAT_1_LABEL) -#define MSG_UBL_VALIDATE_MESH_M2 _UxGT("Netz validieren " PREHEAT_2_LABEL) +#define MSG_UBL_VALIDATE_MESH_M1 _UxGT(PREHEAT_1_LABEL " Netz validieren") +#define MSG_UBL_VALIDATE_MESH_M2 _UxGT(PREHEAT_2_LABEL " Netz validieren") #define MSG_UBL_VALIDATE_CUSTOM_MESH _UxGT("Eig. Netz validieren") #define MSG_UBL_CONTINUE_MESH _UxGT("Netzerst. forts.") #define MSG_UBL_MESH_LEVELING _UxGT("Netz-Nivellierung") @@ -185,7 +187,7 @@ #define MSG_SET_LEDS_VIOLET _UxGT("Violett") #define MSG_SET_LEDS_WHITE _UxGT("Weiß") #define MSG_SET_LEDS_DEFAULT _UxGT("Standard") -#define MSG_CUSTOM_LEDS _UxGT("Benutzerdef.") +#define MSG_CUSTOM_LEDS _UxGT("Benutzerdefiniert") #define MSG_INTENSITY_R _UxGT("Intensität Rot") #define MSG_INTENSITY_G _UxGT("Intensität Grün") #define MSG_INTENSITY_B _UxGT("Intensität Blau") @@ -199,10 +201,10 @@ #define MSG_MOVE_Z _UxGT("Bewege Z") #define MSG_MOVE_E _UxGT("Bewege Extruder") #define MSG_HOTEND_TOO_COLD _UxGT("Hotend zu kalt") -#define MSG_MOVE_0025MM _UxGT(" 0,025 mm") -#define MSG_MOVE_01MM _UxGT(" 0,1 mm") -#define MSG_MOVE_1MM _UxGT(" 1,0 mm") -#define MSG_MOVE_10MM _UxGT("10,0 mm") +#define MSG_MOVE_Z_DIST _UxGT(" %s mm") +#define MSG_MOVE_01MM _UxGT(" 0,1 mm") +#define MSG_MOVE_1MM _UxGT(" 1,0 mm") +#define MSG_MOVE_10MM _UxGT("10,0 mm") #define MSG_SPEED _UxGT("Geschw.") #define MSG_BED_Z _UxGT("Bett Z") #define MSG_NOZZLE _UxGT("Düse") @@ -216,8 +218,8 @@ #define MSG_MAX LCD_STR_THERMOMETER _UxGT(" max") #define MSG_FACTOR LCD_STR_THERMOMETER _UxGT(" Faktor") #define MSG_AUTOTEMP _UxGT("Auto Temperatur") -#define MSG_LCD_ON _UxGT("Ein") -#define MSG_LCD_OFF _UxGT("Aus") +#define MSG_LCD_ON _UxGT("an") +#define MSG_LCD_OFF _UxGT("aus") #define MSG_PID_P _UxGT("PID P") #define MSG_PID_I _UxGT("PID I") #define MSG_PID_D _UxGT("PID D") @@ -282,7 +284,7 @@ #define MSG_TUNE _UxGT("Justierung") #define MSG_START_PRINT _UxGT("Starte Druck") #define MSG_BUTTON_NEXT _UxGT("Weiter") -#define MSG_BUTTON_INIT _UxGT("Init") +#define MSG_BUTTON_INIT _UxGT("Bestätigen") #define MSG_BUTTON_STOP _UxGT("Stop") #define MSG_BUTTON_PRINT _UxGT("Drucken") #define MSG_BUTTON_RESET _UxGT("Zurücksetzen") @@ -304,11 +306,11 @@ #define MSG_STOPPED _UxGT("ANGEHALTEN") #define MSG_CONTROL_RETRACT _UxGT("Einzug mm") #define MSG_CONTROL_RETRACT_SWAP _UxGT("Wechs. Einzug mm") -#define MSG_CONTROL_RETRACTF _UxGT("Einzug V") +#define MSG_CONTROL_RETRACTF _UxGT("V Einzug") #define MSG_CONTROL_RETRACT_ZHOP _UxGT("Z-Sprung mm") #define MSG_CONTROL_RETRACT_RECOVER _UxGT("UnRet mm") #define MSG_CONTROL_RETRACT_RECOVER_SWAP _UxGT("Wechs. UnRet mm") -#define MSG_CONTROL_RETRACT_RECOVERF _UxGT("UnRet V") +#define MSG_CONTROL_RETRACT_RECOVERF _UxGT("UnRet V") #define MSG_CONTROL_RETRACT_RECOVER_SWAPF _UxGT("S UnRet V") #define MSG_AUTORETRACT _UxGT("Autom. Einzug") #define MSG_FILAMENT_SWAP_LENGTH _UxGT("Einzugslänge") @@ -353,7 +355,7 @@ #define MSG_BABYSTEP_Y _UxGT("Babystep Y") #define MSG_BABYSTEP_Z _UxGT("Babystep Z") #define MSG_BABYSTEP_TOTAL _UxGT("Total") -#define MSG_ENDSTOP_ABORT _UxGT("Endstopp Abbr.") +#define MSG_ENDSTOP_ABORT _UxGT("Abbr. mit Endstopp") #define MSG_HEATING_FAILED_LCD _UxGT("HEIZEN ERFOLGLOS") #define MSG_HEATING_FAILED_LCD_BED _UxGT("Bett heizen fehlge.") #define MSG_HEATING_FAILED_LCD_CHAMBER _UxGT("Geh. heizen fehlge.") @@ -368,7 +370,7 @@ #define MSG_ERR_MAXTEMP_CHAMBER _UxGT("Err:Gehäuse max Temp") #define MSG_ERR_MINTEMP_CHAMBER _UxGT("Err:Gehäuse min Temp") #define MSG_ERR_Z_HOMING MSG_HOME _UxGT(" ") MSG_X MSG_Y _UxGT(" ") MSG_FIRST -#define MSG_HALTED _UxGT("DRUCKER STOPP") +#define MSG_HALTED _UxGT("DRUCKER GESTOPPT") #define MSG_PLEASE_RESET _UxGT("Bitte neustarten") #define MSG_SHORT_DAY _UxGT("t") // One character only #define MSG_SHORT_HOUR _UxGT("h") // One character only @@ -488,6 +490,7 @@ #define MSG_VTOOLS_RESET _UxGT("V-Tools ist resetet") #define MSG_START_Z _UxGT("Z Start") #define MSG_END_Z _UxGT("Z Ende") +#define MSG_GAMES _UxGT("Spiele") #define MSG_BRICKOUT _UxGT("Brickout") #define MSG_INVADERS _UxGT("Invaders") #define MSG_SNAKE _UxGT("Sn4k3") diff --git a/Marlin/src/lcd/language/language_el-gr.h b/Marlin/src/lcd/language/language_el-gr.h index 5f8f5d5f99..ea66d3ff00 100644 --- a/Marlin/src/lcd/language/language_el-gr.h +++ b/Marlin/src/lcd/language/language_el-gr.h @@ -72,7 +72,7 @@ #define MSG_MOVE_Y _UxGT("Μετακίνηση Y") #define MSG_MOVE_Z _UxGT("Μετακίνηση Z") #define MSG_MOVE_E _UxGT("Εξωθητήρας") -#define MSG_MOVE_0025MM _UxGT("Μετακίνηση 0,025 μμ") +#define MSG_MOVE_Z_DIST _UxGT("Μετακίνηση %s μμ") #define MSG_MOVE_01MM _UxGT("Μετακίνηση 0,1 μμ") #define MSG_MOVE_1MM _UxGT("Μετακίνηση 1 μμ") #define MSG_MOVE_10MM _UxGT("Μετακίνηση 10 μμ") diff --git a/Marlin/src/lcd/language/language_el.h b/Marlin/src/lcd/language/language_el.h index 7a846c614e..2425309f7a 100644 --- a/Marlin/src/lcd/language/language_el.h +++ b/Marlin/src/lcd/language/language_el.h @@ -72,7 +72,7 @@ #define MSG_MOVE_Y _UxGT("Μετακίνηση Y") #define MSG_MOVE_Z _UxGT("Μετακίνηση Z") #define MSG_MOVE_E _UxGT("Εξωθητήρας") -#define MSG_MOVE_0025MM _UxGT("Μετακίνηση 0,025 μμ") +#define MSG_MOVE_Z_DIST _UxGT("Μετακίνηση %s μμ") #define MSG_MOVE_01MM _UxGT("Μετακίνηση 0,1 μμ") #define MSG_MOVE_1MM _UxGT("Μετακίνηση 1 μμ") #define MSG_MOVE_10MM _UxGT("Μετακίνηση 10 μμ") diff --git a/Marlin/src/lcd/language/language_en.h b/Marlin/src/lcd/language/language_en.h index c2a629923d..fb53a130a1 100644 --- a/Marlin/src/lcd/language/language_en.h +++ b/Marlin/src/lcd/language/language_en.h @@ -62,13 +62,13 @@ #define MSG_BACK _UxGT("Back") #endif #ifndef MSG_SD_INSERTED - #define MSG_SD_INSERTED _UxGT("Card inserted") + #define MSG_SD_INSERTED _UxGT("Card Inserted") #endif #ifndef MSG_SD_REMOVED - #define MSG_SD_REMOVED _UxGT("Card removed") + #define MSG_SD_REMOVED _UxGT("Card Removed") #endif #ifndef MSG_SD_RELEASED - #define MSG_SD_RELEASED _UxGT("Card released") + #define MSG_SD_RELEASED _UxGT("Card Released") #endif #ifndef MSG_LCD_ENDSTOPS #define MSG_LCD_ENDSTOPS _UxGT("Endstops") // Max length 8 characters @@ -89,7 +89,7 @@ #define MSG_AUTOSTART _UxGT("Autostart") #endif #ifndef MSG_DISABLE_STEPPERS - #define MSG_DISABLE_STEPPERS _UxGT("Disable steppers") + #define MSG_DISABLE_STEPPERS _UxGT("Disable Steppers") #endif #ifndef MSG_DEBUG_MENU #define MSG_DEBUG_MENU _UxGT("Debug Menu") @@ -98,7 +98,7 @@ #define MSG_PROGRESS_BAR_TEST _UxGT("Progress Bar Test") #endif #ifndef MSG_AUTO_HOME - #define MSG_AUTO_HOME _UxGT("Auto home") + #define MSG_AUTO_HOME _UxGT("Auto Home") #endif #ifndef MSG_AUTO_HOME_X #define MSG_AUTO_HOME_X _UxGT("Home X") @@ -128,13 +128,13 @@ #define MSG_Z_FADE_HEIGHT _UxGT("Fade Height") #endif #ifndef MSG_SET_HOME_OFFSETS - #define MSG_SET_HOME_OFFSETS _UxGT("Set home offsets") + #define MSG_SET_HOME_OFFSETS _UxGT("Set Home Offsets") #endif #ifndef MSG_HOME_OFFSETS_APPLIED - #define MSG_HOME_OFFSETS_APPLIED _UxGT("Offsets applied") + #define MSG_HOME_OFFSETS_APPLIED _UxGT("Offsets Applied") #endif #ifndef MSG_SET_ORIGIN - #define MSG_SET_ORIGIN _UxGT("Set origin") + #define MSG_SET_ORIGIN _UxGT("Set Origin") #endif #ifndef MSG_PREHEAT_1 #define MSG_PREHEAT_1 _UxGT("Preheat " PREHEAT_1_LABEL) @@ -152,7 +152,7 @@ #define MSG_PREHEAT_1_BEDONLY MSG_PREHEAT_1 _UxGT(" Bed") #endif #ifndef MSG_PREHEAT_1_SETTINGS - #define MSG_PREHEAT_1_SETTINGS MSG_PREHEAT_1 _UxGT(" conf") + #define MSG_PREHEAT_1_SETTINGS MSG_PREHEAT_1 _UxGT(" Conf") #endif #ifndef MSG_PREHEAT_2 #define MSG_PREHEAT_2 _UxGT("Preheat " PREHEAT_2_LABEL) @@ -170,7 +170,7 @@ #define MSG_PREHEAT_2_BEDONLY MSG_PREHEAT_2 _UxGT(" Bed") #endif #ifndef MSG_PREHEAT_2_SETTINGS - #define MSG_PREHEAT_2_SETTINGS MSG_PREHEAT_2 _UxGT(" conf") + #define MSG_PREHEAT_2_SETTINGS MSG_PREHEAT_2 _UxGT(" Conf") #endif #ifndef MSG_PREHEAT_CUSTOM #define MSG_PREHEAT_CUSTOM _UxGT("Preheat Custom") @@ -188,7 +188,7 @@ #define MSG_LASER_ON _UxGT("Laser On") #endif #ifndef MSG_LASER_POWER - #define MSG_LASER_POWER _UxGT("Laser power") + #define MSG_LASER_POWER _UxGT("Laser Power") #endif #ifndef MSG_SPINDLE_MENU #define MSG_SPINDLE_MENU _UxGT("Spindle Control") @@ -200,16 +200,16 @@ #define MSG_SPINDLE_ON _UxGT("Spindle On") #endif #ifndef MSG_SPINDLE_POWER - #define MSG_SPINDLE_POWER _UxGT("Spindle power") + #define MSG_SPINDLE_POWER _UxGT("Spindle Power") #endif #ifndef MSG_SPINDLE_REVERSE #define MSG_SPINDLE_REVERSE _UxGT("Spindle Reverse") #endif #ifndef MSG_SWITCH_PS_ON - #define MSG_SWITCH_PS_ON _UxGT("Switch power on") + #define MSG_SWITCH_PS_ON _UxGT("Switch Power On") #endif #ifndef MSG_SWITCH_PS_OFF - #define MSG_SWITCH_PS_OFF _UxGT("Switch power off") + #define MSG_SWITCH_PS_OFF _UxGT("Switch Power Off") #endif #ifndef MSG_EXTRUDE #define MSG_EXTRUDE _UxGT("Extrude") @@ -218,23 +218,26 @@ #define MSG_RETRACT _UxGT("Retract") #endif #ifndef MSG_MOVE_AXIS - #define MSG_MOVE_AXIS _UxGT("Move axis") + #define MSG_MOVE_AXIS _UxGT("Move Axis") #endif #ifndef MSG_BED_LEVELING #define MSG_BED_LEVELING _UxGT("Bed Leveling") #endif #ifndef MSG_LEVEL_BED - #define MSG_LEVEL_BED _UxGT("Level bed") + #define MSG_LEVEL_BED _UxGT("Level Bed") #endif #ifndef MSG_LEVEL_CORNERS - #define MSG_LEVEL_CORNERS _UxGT("Level corners") + #define MSG_LEVEL_CORNERS _UxGT("Level Corners") #endif #ifndef MSG_NEXT_CORNER - #define MSG_NEXT_CORNER _UxGT("Next corner") + #define MSG_NEXT_CORNER _UxGT("Next Corner") #endif #ifndef MSG_EDITING_STOPPED #define MSG_EDITING_STOPPED _UxGT("Mesh Editing Stopped") #endif +#ifndef MSG_PROBING_MESH + #define MSG_PROBING_MESH _UxGT("Probing Point") +#endif #ifndef MSG_MESH_X #define MSG_MESH_X _UxGT("Index X") #endif @@ -251,7 +254,7 @@ #define MSG_UBL_DOING_G29 _UxGT("Doing G29") #endif #ifndef MSG_UBL_UNHOMED - #define MSG_UBL_UNHOMED _UxGT("Home XYZ first") + #define MSG_UBL_UNHOMED _UxGT("Home XYZ First") #endif #ifndef MSG_UBL_TOOLS #define MSG_UBL_TOOLS _UxGT("UBL Tools") @@ -259,11 +262,14 @@ #ifndef MSG_UBL_LEVEL_BED #define MSG_UBL_LEVEL_BED _UxGT("Unified Bed Leveling") #endif -#ifndef MSG_LCD_PROBING_MESH - #define MSG_LCD_PROBING_MESH _UxGT("Probing point") -#endif #ifndef MSG_LCD_TILTING_MESH - #define MSG_LCD_TILTING_MESH _UxGT("Tilting point") + #define MSG_LCD_TILTING_MESH _UxGT("Tilting Point") +#endif +#ifndef MSG_M48_TEST + #define MSG_M48_TEST _UxGT("M48 Probe Test") +#endif +#ifndef MSG_M48_DEVIATION + #define MSG_M48_DEVIATION _UxGT("Deviation") #endif #ifndef MSG_IDEX_MENU #define MSG_IDEX_MENU _UxGT("IDEX Mode") @@ -278,31 +284,31 @@ #define MSG_IDEX_MODE_DUPLICATE _UxGT("Duplication") #endif #ifndef MSG_IDEX_MODE_MIRRORED_COPY - #define MSG_IDEX_MODE_MIRRORED_COPY _UxGT("Mirrored copy") + #define MSG_IDEX_MODE_MIRRORED_COPY _UxGT("Mirrored Copy") #endif #ifndef MSG_IDEX_MODE_FULL_CTRL - #define MSG_IDEX_MODE_FULL_CTRL _UxGT("Full control") + #define MSG_IDEX_MODE_FULL_CTRL _UxGT("Full Control") #endif #ifndef MSG_X_OFFSET - #define MSG_X_OFFSET _UxGT("2nd nozzle X") + #define MSG_X_OFFSET _UxGT("2nd Nozzle X") #endif #ifndef MSG_Y_OFFSET - #define MSG_Y_OFFSET _UxGT("2nd nozzle Y") + #define MSG_Y_OFFSET _UxGT("2nd Nozzle Y") #endif #ifndef MSG_Z_OFFSET - #define MSG_Z_OFFSET _UxGT("2nd nozzle Z") + #define MSG_Z_OFFSET _UxGT("2nd nNozzle Z") #endif #ifndef MSG_UBL_MANUAL_MESH #define MSG_UBL_MANUAL_MESH _UxGT("Manually Build Mesh") #endif #ifndef MSG_UBL_BC_INSERT - #define MSG_UBL_BC_INSERT _UxGT("Place shim & measure") + #define MSG_UBL_BC_INSERT _UxGT("Place Shim & Measure") #endif #ifndef MSG_UBL_BC_INSERT2 #define MSG_UBL_BC_INSERT2 _UxGT("Measure") #endif #ifndef MSG_UBL_BC_REMOVE - #define MSG_UBL_BC_REMOVE _UxGT("Remove & measure bed") + #define MSG_UBL_BC_REMOVE _UxGT("Remove & Measure Bed") #endif #ifndef MSG_UBL_MOVING_TO_NEXT #define MSG_UBL_MOVING_TO_NEXT _UxGT("Moving to next") @@ -446,13 +452,13 @@ #define MSG_UBL_SAVE_MESH _UxGT("Save Bed Mesh") #endif #ifndef MSG_MESH_LOADED - #define MSG_MESH_LOADED _UxGT("Mesh %i loaded") + #define MSG_MESH_LOADED _UxGT("Mesh %i Loaded") #endif #ifndef MSG_MESH_SAVED - #define MSG_MESH_SAVED _UxGT("Mesh %i saved") + #define MSG_MESH_SAVED _UxGT("Mesh %i Saved") #endif #ifndef MSG_NO_STORAGE - #define MSG_NO_STORAGE _UxGT("No storage") + #define MSG_NO_STORAGE _UxGT("No Storage") #endif #ifndef MSG_UBL_SAVE_ERROR #define MSG_UBL_SAVE_ERROR _UxGT("Err: UBL Save") @@ -543,8 +549,8 @@ #ifndef MSG_HOTEND_TOO_COLD #define MSG_HOTEND_TOO_COLD _UxGT("Hotend too cold") #endif -#ifndef MSG_MOVE_0025MM - #define MSG_MOVE_0025MM _UxGT("Move 0.025mm") +#ifndef MSG_MOVE_Z_DIST + #define MSG_MOVE_Z_DIST _UxGT("Move %smm") #endif #ifndef MSG_MOVE_01MM #define MSG_MOVE_01MM _UxGT("Move 0.1mm") @@ -571,10 +577,10 @@ #define MSG_CHAMBER _UxGT("Enclosure") #endif #ifndef MSG_FAN_SPEED - #define MSG_FAN_SPEED _UxGT("Fan speed") + #define MSG_FAN_SPEED _UxGT("Fan Speed") #endif #ifndef MSG_EXTRA_FAN_SPEED - #define MSG_EXTRA_FAN_SPEED _UxGT("Extra fan speed") + #define MSG_EXTRA_FAN_SPEED _UxGT("Extra Fan Speed") #endif #ifndef MSG_FLOW #define MSG_FLOW _UxGT("Flow") @@ -623,27 +629,27 @@ #endif #if IS_KINEMATIC #ifndef MSG_VA_JERK - #define MSG_VA_JERK _UxGT("Va-jerk") + #define MSG_VA_JERK _UxGT("Va-Jerk") #endif #ifndef MSG_VB_JERK - #define MSG_VB_JERK _UxGT("Vb-jerk") + #define MSG_VB_JERK _UxGT("Vb-Jerk") #endif #ifndef MSG_VC_JERK - #define MSG_VC_JERK _UxGT("Vc-jerk") + #define MSG_VC_JERK _UxGT("Vc-Jerk") #endif #else #ifndef MSG_VA_JERK - #define MSG_VA_JERK _UxGT("Vx-jerk") + #define MSG_VA_JERK _UxGT("Vx-Jerk") #endif #ifndef MSG_VB_JERK - #define MSG_VB_JERK _UxGT("Vy-jerk") + #define MSG_VB_JERK _UxGT("Vy-Jerk") #endif #ifndef MSG_VC_JERK - #define MSG_VC_JERK _UxGT("Vz-jerk") + #define MSG_VC_JERK _UxGT("Vz-Jerk") #endif #endif #ifndef MSG_VE_JERK - #define MSG_VE_JERK _UxGT("Ve-jerk") + #define MSG_VE_JERK _UxGT("Ve-Jerk") #endif #ifndef MSG_JUNCTION_DEVIATION #define MSG_JUNCTION_DEVIATION _UxGT("Junction Dev") @@ -658,7 +664,7 @@ #define MSG_VMIN _UxGT("Vmin") #endif #ifndef MSG_VTRAV_MIN - #define MSG_VTRAV_MIN _UxGT("VTrav min") + #define MSG_VTRAV_MIN _UxGT("VTrav Min") #endif #ifndef MSG_ACCELERATION #define MSG_ACCELERATION _UxGT("Acceleration") @@ -667,10 +673,10 @@ #define MSG_AMAX _UxGT("Amax ") #endif #ifndef MSG_A_RETRACT - #define MSG_A_RETRACT _UxGT("A-retract") + #define MSG_A_RETRACT _UxGT("A-Retract") #endif #ifndef MSG_A_TRAVEL - #define MSG_A_TRAVEL _UxGT("A-travel") + #define MSG_A_TRAVEL _UxGT("A-Travel") #endif #ifndef MSG_STEPS_PER_MM #define MSG_STEPS_PER_MM _UxGT("Steps/mm") @@ -742,13 +748,13 @@ #define MSG_ADVANCE_K _UxGT("Advance K") #endif #ifndef MSG_CONTRAST - #define MSG_CONTRAST _UxGT("LCD contrast") + #define MSG_CONTRAST _UxGT("LCD Contrast") #endif #ifndef MSG_STORE_EEPROM - #define MSG_STORE_EEPROM _UxGT("Store settings") + #define MSG_STORE_EEPROM _UxGT("Store Settings") #endif #ifndef MSG_LOAD_EEPROM - #define MSG_LOAD_EEPROM _UxGT("Load settings") + #define MSG_LOAD_EEPROM _UxGT("Load Settings") #endif #ifndef MSG_RESTORE_FAILSAFE #define MSG_RESTORE_FAILSAFE _UxGT("Restore failsafe") @@ -766,7 +772,7 @@ #define MSG_REFRESH _UxGT("Refresh") #endif #ifndef MSG_WATCH - #define MSG_WATCH _UxGT("Info screen") + #define MSG_WATCH _UxGT("Info Screen") #endif #ifndef MSG_PREPARE #define MSG_PREPARE _UxGT("Prepare") @@ -775,7 +781,7 @@ #define MSG_TUNE _UxGT("Tune") #endif #ifndef MSG_START_PRINT - #define MSG_START_PRINT _UxGT("Start print") + #define MSG_START_PRINT _UxGT("Start Print") #endif #ifndef MSG_BUTTON_NEXT #define MSG_BUTTON_NEXT _UxGT("Next") @@ -799,13 +805,13 @@ #define MSG_BUTTON_DONE _UxGT("Done") #endif #ifndef MSG_PAUSE_PRINT - #define MSG_PAUSE_PRINT _UxGT("Pause print") + #define MSG_PAUSE_PRINT _UxGT("Pause Print") #endif #ifndef MSG_RESUME_PRINT - #define MSG_RESUME_PRINT _UxGT("Resume print") + #define MSG_RESUME_PRINT _UxGT("Resume Print") #endif #ifndef MSG_STOP_PRINT - #define MSG_STOP_PRINT _UxGT("Stop print") + #define MSG_STOP_PRINT _UxGT("Stop Print") #endif #ifndef MSG_OUTAGE_RECOVERY #define MSG_OUTAGE_RECOVERY _UxGT("Outage Recovery") @@ -814,25 +820,25 @@ #define MSG_CARD_MENU _UxGT("Print from SD") #endif #ifndef MSG_NO_CARD - #define MSG_NO_CARD _UxGT("No SD card") + #define MSG_NO_CARD _UxGT("No SD Card") #endif #ifndef MSG_DWELL #define MSG_DWELL _UxGT("Sleep...") #endif #ifndef MSG_USERWAIT - #define MSG_USERWAIT _UxGT("Click to resume...") + #define MSG_USERWAIT _UxGT("Click to Resume...") #endif #ifndef MSG_PRINT_PAUSED - #define MSG_PRINT_PAUSED _UxGT("Print paused") + #define MSG_PRINT_PAUSED _UxGT("Print Paused") #endif #ifndef MSG_PRINTING #define MSG_PRINTING _UxGT("Printing...") #endif #ifndef MSG_PRINT_ABORTED - #define MSG_PRINT_ABORTED _UxGT("Print aborted") + #define MSG_PRINT_ABORTED _UxGT("Print Aborted") #endif #ifndef MSG_NO_MOVE - #define MSG_NO_MOVE _UxGT("No move.") + #define MSG_NO_MOVE _UxGT("No Move.") #endif #ifndef MSG_KILLED #define MSG_KILLED _UxGT("KILLED. ") @@ -868,13 +874,16 @@ #define MSG_AUTORETRACT _UxGT("AutoRetr.") #endif #ifndef MSG_FILAMENT_SWAP_LENGTH - #define MSG_FILAMENT_SWAP_LENGTH _UxGT("Retract Distance") + #define MSG_FILAMENT_SWAP_LENGTH _UxGT("Swap Length") +#endif +#ifndef MSG_FILAMENT_PURGE_LENGTH + #define MSG_FILAMENT_PURGE_LENGTH _UxGT("Purge Length") #endif #ifndef MSG_TOOL_CHANGE - #define MSG_TOOL_CHANGE _UxGT("Tool Change") + #define MSG_TOOL_CHANGE _UxGT("Tool Change") #endif #ifndef MSG_TOOL_CHANGE_ZLIFT - #define MSG_TOOL_CHANGE_ZLIFT _UxGT("Z Raise") + #define MSG_TOOL_CHANGE_ZLIFT _UxGT("Z Raise") #endif #ifndef MSG_SINGLENOZZLE_PRIME_SPD #define MSG_SINGLENOZZLE_PRIME_SPD _UxGT("Prime Speed") @@ -886,28 +895,28 @@ #define MSG_NOZZLE_STANDBY _UxGT("Nozzle Standby") #endif #ifndef MSG_FILAMENTCHANGE - #define MSG_FILAMENTCHANGE _UxGT("Change filament") + #define MSG_FILAMENTCHANGE _UxGT("Change Filament") #endif #ifndef MSG_FILAMENTLOAD - #define MSG_FILAMENTLOAD _UxGT("Load filament") + #define MSG_FILAMENTLOAD _UxGT("Load Filament") #endif #ifndef MSG_FILAMENTUNLOAD - #define MSG_FILAMENTUNLOAD _UxGT("Unload filament") + #define MSG_FILAMENTUNLOAD _UxGT("Unload Filament") #endif #ifndef MSG_FILAMENTUNLOAD_ALL #define MSG_FILAMENTUNLOAD_ALL _UxGT("Unload All") #endif #ifndef MSG_INIT_SDCARD - #define MSG_INIT_SDCARD _UxGT("Init. SD card") + #define MSG_INIT_SDCARD _UxGT("Init. SD Card") #endif #ifndef MSG_CHANGE_SDCARD - #define MSG_CHANGE_SDCARD _UxGT("Change SD card") + #define MSG_CHANGE_SDCARD _UxGT("Change SD Card") #endif #ifndef MSG_RELEASE_SDCARD - #define MSG_RELEASE_SDCARD _UxGT("Release SD card") + #define MSG_RELEASE_SDCARD _UxGT("Release SD Card") #endif #ifndef MSG_ZPROBE_OUT - #define MSG_ZPROBE_OUT _UxGT("Z Probe past bed") + #define MSG_ZPROBE_OUT _UxGT("Z Probe Past Bed") #endif #ifndef MSG_SKEW_FACTOR #define MSG_SKEW_FACTOR _UxGT("Skew Factor") @@ -958,7 +967,7 @@ #define MSG_TOUCHMI_INIT _UxGT("Init TouchMI") #endif #ifndef MSG_TOUCHMI_ZTEST - #define MSG_TOUCHMI_ZTEST _UxGT("Z offset Test") + #define MSG_TOUCHMI_ZTEST _UxGT("Z Offset Test") #endif #ifndef MSG_TOUCHMI_SAVE #define MSG_TOUCHMI_SAVE _UxGT("Save") @@ -976,7 +985,7 @@ #define MSG_HOME _UxGT("Home") // Used as MSG_HOME " " MSG_X MSG_Y MSG_Z " " MSG_FIRST #endif #ifndef MSG_FIRST - #define MSG_FIRST _UxGT("first") + #define MSG_FIRST _UxGT("First") #endif #ifndef MSG_ZPROBE_ZOFFSET #define MSG_ZPROBE_ZOFFSET _UxGT("Probe Z Offset") @@ -994,16 +1003,16 @@ #define MSG_BABYSTEP_TOTAL _UxGT("Total") #endif #ifndef MSG_ENDSTOP_ABORT - #define MSG_ENDSTOP_ABORT _UxGT("Endstop abort") + #define MSG_ENDSTOP_ABORT _UxGT("Endstop Abort") #endif #ifndef MSG_HEATING_FAILED_LCD - #define MSG_HEATING_FAILED_LCD _UxGT("Heating failed") + #define MSG_HEATING_FAILED_LCD _UxGT("Heating Failed") #endif #ifndef MSG_HEATING_FAILED_LCD_BED - #define MSG_HEATING_FAILED_LCD_BED _UxGT("Bed heating failed") + #define MSG_HEATING_FAILED_LCD_BED _UxGT("Bed Heating Failed") #endif #ifndef MSG_HEATING_FAILED_LCD_CHAMBER - #define MSG_HEATING_FAILED_LCD_CHAMBER _UxGT("Chamber heating fail") + #define MSG_HEATING_FAILED_LCD_CHAMBER _UxGT("Chamber Heating Fail") #endif #ifndef MSG_ERR_REDUNDANT_TEMP #define MSG_ERR_REDUNDANT_TEMP _UxGT("Err: REDUNDANT TEMP") @@ -1042,7 +1051,7 @@ #define MSG_HALTED _UxGT("PRINTER HALTED") #endif #ifndef MSG_PLEASE_RESET - #define MSG_PLEASE_RESET _UxGT("Please reset") + #define MSG_PLEASE_RESET _UxGT("Please Reset") #endif #ifndef MSG_SHORT_DAY #define MSG_SHORT_DAY _UxGT("d") // One character only @@ -1060,16 +1069,16 @@ #define MSG_COOLING _UxGT("Cooling...") #endif #ifndef MSG_BED_HEATING - #define MSG_BED_HEATING _UxGT("Bed heating...") + #define MSG_BED_HEATING _UxGT("Bed Heating...") #endif #ifndef MSG_BED_COOLING - #define MSG_BED_COOLING _UxGT("Bed cooling...") + #define MSG_BED_COOLING _UxGT("Bed Cooling...") #endif #ifndef MSG_CHAMBER_HEATING - #define MSG_CHAMBER_HEATING _UxGT("Chamber heating...") + #define MSG_CHAMBER_HEATING _UxGT("Chamber Heating...") #endif #ifndef MSG_CHAMBER_COOLING - #define MSG_CHAMBER_COOLING _UxGT("Chamber cooling...") + #define MSG_CHAMBER_COOLING _UxGT("Chamber Cooling...") #endif #ifndef MSG_DELTA_CALIBRATE #define MSG_DELTA_CALIBRATE _UxGT("Delta Calibration") @@ -1147,7 +1156,7 @@ #define MSG_INFO_PROTOCOL _UxGT("Protocol") #endif #ifndef MSG_CASE_LIGHT - #define MSG_CASE_LIGHT _UxGT("Case light") + #define MSG_CASE_LIGHT _UxGT("Case Light") #endif #ifndef MSG_CASE_LIGHT_BRIGHTNESS #define MSG_CASE_LIGHT_BRIGHTNESS _UxGT("Light Brightness") @@ -1160,13 +1169,13 @@ #define MSG_INFO_COMPLETED_PRINTS _UxGT("Completed") #endif #ifndef MSG_INFO_PRINT_TIME - #define MSG_INFO_PRINT_TIME _UxGT("Total print time") + #define MSG_INFO_PRINT_TIME _UxGT("Total Print time") #endif #ifndef MSG_INFO_PRINT_LONGEST - #define MSG_INFO_PRINT_LONGEST _UxGT("Longest job time") + #define MSG_INFO_PRINT_LONGEST _UxGT("Longest Job Time") #endif #ifndef MSG_INFO_PRINT_FILAMENT - #define MSG_INFO_PRINT_FILAMENT _UxGT("Extruded total") + #define MSG_INFO_PRINT_FILAMENT _UxGT("Extruded Total") #endif #else #ifndef MSG_INFO_PRINT_COUNT @@ -1231,13 +1240,13 @@ #define MSG_RUNOUT_DISTANCE_MM _UxGT("Runout Dist mm") #endif #ifndef MSG_ERR_HOMING_FAILED - #define MSG_ERR_HOMING_FAILED _UxGT("Homing failed") + #define MSG_ERR_HOMING_FAILED _UxGT("Homing Failed") #endif #ifndef MSG_ERR_PROBING_FAILED - #define MSG_ERR_PROBING_FAILED _UxGT("Probing failed") + #define MSG_ERR_PROBING_FAILED _UxGT("Probing Failed") #endif #ifndef MSG_M600_TOO_COLD - #define MSG_M600_TOO_COLD _UxGT("M600: Too cold") + #define MSG_M600_TOO_COLD _UxGT("M600: Too Cold") #endif #ifndef MSG_MMU2_FILAMENT_CHANGE_HEADER @@ -1250,55 +1259,55 @@ #define MSG_MMU2_MENU _UxGT("MMU") #endif #ifndef MSG_MMU2_WRONG_FIRMWARE - #define MSG_MMU2_WRONG_FIRMWARE _UxGT("Update MMU firmware!") + #define MSG_MMU2_WRONG_FIRMWARE _UxGT("Update MMU Firmware!") #endif #ifndef MSG_MMU2_NOT_RESPONDING - #define MSG_MMU2_NOT_RESPONDING _UxGT("MMU needs attention.") + #define MSG_MMU2_NOT_RESPONDING _UxGT("MMU Needs Attention.") #endif #ifndef MSG_MMU2_RESUME - #define MSG_MMU2_RESUME _UxGT("Resume print") + #define MSG_MMU2_RESUME _UxGT("Resume Print") #endif #ifndef MSG_MMU2_RESUMING #define MSG_MMU2_RESUMING _UxGT("Resuming...") #endif #ifndef MSG_MMU2_LOAD_FILAMENT - #define MSG_MMU2_LOAD_FILAMENT _UxGT("Load filament") + #define MSG_MMU2_LOAD_FILAMENT _UxGT("Load Filament") #endif #ifndef MSG_MMU2_LOAD_ALL - #define MSG_MMU2_LOAD_ALL _UxGT("Load all") + #define MSG_MMU2_LOAD_ALL _UxGT("Load All") #endif #ifndef MSG_MMU2_LOAD_TO_NOZZLE - #define MSG_MMU2_LOAD_TO_NOZZLE _UxGT("Load to nozzle") + #define MSG_MMU2_LOAD_TO_NOZZLE _UxGT("Load to Nozzle") #endif #ifndef MSG_MMU2_EJECT_FILAMENT - #define MSG_MMU2_EJECT_FILAMENT _UxGT("Eject filament") + #define MSG_MMU2_EJECT_FILAMENT _UxGT("Eject Filament") #endif #ifndef MSG_MMU2_EJECT_FILAMENT0 - #define MSG_MMU2_EJECT_FILAMENT0 _UxGT("Eject filament 1") + #define MSG_MMU2_EJECT_FILAMENT0 _UxGT("Eject Filament 1") #endif #ifndef MSG_MMU2_EJECT_FILAMENT1 - #define MSG_MMU2_EJECT_FILAMENT1 _UxGT("Eject filament 2") + #define MSG_MMU2_EJECT_FILAMENT1 _UxGT("Eject Filament 2") #endif #ifndef MSG_MMU2_EJECT_FILAMENT2 - #define MSG_MMU2_EJECT_FILAMENT2 _UxGT("Eject filament 3") + #define MSG_MMU2_EJECT_FILAMENT2 _UxGT("Eject Filament 3") #endif #ifndef MSG_MMU2_EJECT_FILAMENT3 - #define MSG_MMU2_EJECT_FILAMENT3 _UxGT("Eject filament 4") + #define MSG_MMU2_EJECT_FILAMENT3 _UxGT("Eject Filament 4") #endif #ifndef MSG_MMU2_EJECT_FILAMENT4 - #define MSG_MMU2_EJECT_FILAMENT4 _UxGT("Eject filament 5") + #define MSG_MMU2_EJECT_FILAMENT4 _UxGT("Eject Filament 5") #endif #ifndef MSG_MMU2_UNLOAD_FILAMENT - #define MSG_MMU2_UNLOAD_FILAMENT _UxGT("Unload filament") + #define MSG_MMU2_UNLOAD_FILAMENT _UxGT("Unload Filament") #endif #ifndef MSG_MMU2_LOADING_FILAMENT - #define MSG_MMU2_LOADING_FILAMENT _UxGT("Loading fil. %i...") + #define MSG_MMU2_LOADING_FILAMENT _UxGT("Loading Fil. %i...") #endif #ifndef MSG_MMU2_EJECTING_FILAMENT - #define MSG_MMU2_EJECTING_FILAMENT _UxGT("Ejecting fil. ...") + #define MSG_MMU2_EJECTING_FILAMENT _UxGT("Ejecting Fil. ...") #endif #ifndef MSG_MMU2_UNLOADING_FILAMENT - #define MSG_MMU2_UNLOADING_FILAMENT _UxGT("Unloading fil....") + #define MSG_MMU2_UNLOADING_FILAMENT _UxGT("Unloading Fil....") #endif #ifndef MSG_MMU2_ALL #define MSG_MMU2_ALL _UxGT("All") @@ -1341,16 +1350,16 @@ #define MSG_GRADIENT _UxGT("Gradient") #endif #ifndef MSG_FULL_GRADIENT - #define MSG_FULL_GRADIENT _UxGT("Full gradient") + #define MSG_FULL_GRADIENT _UxGT("Full Gradient") #endif #ifndef MSG_TOGGLE_MIX - #define MSG_TOGGLE_MIX _UxGT("Toggle mix") + #define MSG_TOGGLE_MIX _UxGT("Toggle Mix") #endif #ifndef MSG_CYCLE_MIX - #define MSG_CYCLE_MIX _UxGT("Cycle mix") + #define MSG_CYCLE_MIX _UxGT("Cycle Mix") #endif #ifndef MSG_GRADIENT_MIX - #define MSG_GRADIENT_MIX _UxGT("Gradient mix") + #define MSG_GRADIENT_MIX _UxGT("Gradient Mix") #endif #ifndef MSG_REVERSE_GRADIENT #define MSG_REVERSE_GRADIENT _UxGT("Reverse Gradient") @@ -1374,7 +1383,7 @@ #define MSG_COMMIT_VTOOL _UxGT("Commit V-tool Mix") #endif #ifndef MSG_VTOOLS_RESET - #define MSG_VTOOLS_RESET _UxGT("V-tools were reset") + #define MSG_VTOOLS_RESET _UxGT("V-tools Were Reset") #endif #ifndef MSG_START_Z #define MSG_START_Z _UxGT("Start Z") @@ -1382,6 +1391,10 @@ #ifndef MSG_END_Z #define MSG_END_Z _UxGT(" End Z") #endif + +#ifndef MSG_GAMES + #define MSG_GAMES _UxGT("Games") +#endif #ifndef MSG_BRICKOUT #define MSG_BRICKOUT _UxGT("Brickout") #endif @@ -1401,7 +1414,7 @@ // #if LCD_HEIGHT >= 4 #ifndef MSG_ADVANCED_PAUSE_WAITING_1 - #define MSG_ADVANCED_PAUSE_WAITING_1 _UxGT("Press button") + #define MSG_ADVANCED_PAUSE_WAITING_1 _UxGT("Press Button") #define MSG_ADVANCED_PAUSE_WAITING_2 _UxGT("to resume print") #endif #ifndef MSG_PAUSE_PRINT_INIT_1 @@ -1482,22 +1495,22 @@ #endif // LCD_HEIGHT < 4 #ifndef MSG_TMC_DRIVERS - #define MSG_TMC_DRIVERS _UxGT("TMC drivers") + #define MSG_TMC_DRIVERS _UxGT("TMC Drivers") #endif #ifndef MSG_TMC_CURRENT - #define MSG_TMC_CURRENT _UxGT("Driver current") + #define MSG_TMC_CURRENT _UxGT("Driver Current") #endif #ifndef MSG_TMC_HYBRID_THRS - #define MSG_TMC_HYBRID_THRS _UxGT("Hybrid threshold") + #define MSG_TMC_HYBRID_THRS _UxGT("Hybrid Threshold") #endif #ifndef MSG_TMC_HOMING_THRS - #define MSG_TMC_HOMING_THRS _UxGT("Sensorless homing") + #define MSG_TMC_HOMING_THRS _UxGT("Sensorless Homing") #endif #ifndef MSG_TMC_STEPPING_MODE - #define MSG_TMC_STEPPING_MODE _UxGT("Stepping mode") + #define MSG_TMC_STEPPING_MODE _UxGT("Stepping Mode") #endif #ifndef MSG_TMC_STEALTH_ENABLED - #define MSG_TMC_STEALTH_ENABLED _UxGT("StealthChop enabled") + #define MSG_TMC_STEALTH_ENABLED _UxGT("StealthChop Enabled") #endif #ifndef MSG_SERVICE_RESET diff --git a/Marlin/src/lcd/language/language_es.h b/Marlin/src/lcd/language/language_es.h index 2435020ed1..2d4f1ac2b4 100644 --- a/Marlin/src/lcd/language/language_es.h +++ b/Marlin/src/lcd/language/language_es.h @@ -80,7 +80,7 @@ #define MSG_MOVE_Y _UxGT("Mover Y") #define MSG_MOVE_Z _UxGT("Mover Z") #define MSG_MOVE_E _UxGT("Extrusor") -#define MSG_MOVE_0025MM _UxGT("Mover 0.025mm") +#define MSG_MOVE_Z_DIST _UxGT("Mover %smm") #define MSG_MOVE_01MM _UxGT("Mover 0.1mm") #define MSG_MOVE_1MM _UxGT("Mover 1mm") #define MSG_MOVE_10MM _UxGT("Mover 10mm") diff --git a/Marlin/src/lcd/language/language_eu.h b/Marlin/src/lcd/language/language_eu.h index a550260be4..ae2c98610f 100644 --- a/Marlin/src/lcd/language/language_eu.h +++ b/Marlin/src/lcd/language/language_eu.h @@ -166,7 +166,7 @@ #define MSG_MOVE_Y _UxGT("Mugitu Y") #define MSG_MOVE_Z _UxGT("Mugitu Z") #define MSG_MOVE_E _UxGT("Estrusorea") -#define MSG_MOVE_0025MM _UxGT("Mugitu 0.025mm") +#define MSG_MOVE_Z_DIST _UxGT("Mugitu %smm") #define MSG_MOVE_01MM _UxGT("Mugitu 0.1mm") #define MSG_MOVE_1MM _UxGT("Mugitu 1mm") #define MSG_MOVE_10MM _UxGT("Mugitu 10mm") diff --git a/Marlin/src/lcd/language/language_fi.h b/Marlin/src/lcd/language/language_fi.h index 101d7b44bc..185cc8ac19 100644 --- a/Marlin/src/lcd/language/language_fi.h +++ b/Marlin/src/lcd/language/language_fi.h @@ -65,7 +65,7 @@ #define MSG_MOVE_Y _UxGT("Liikuta Y") #define MSG_MOVE_Z _UxGT("Liikuta Z") #define MSG_MOVE_E _UxGT("Extruder") -#define MSG_MOVE_0025MM _UxGT("Liikuta 0.025mm") +#define MSG_MOVE_Z_DIST _UxGT("Liikuta %smm") #define MSG_MOVE_01MM _UxGT("Liikuta 0.1mm") #define MSG_MOVE_1MM _UxGT("Liikuta 1mm") #define MSG_MOVE_10MM _UxGT("Liikuta 10mm") diff --git a/Marlin/src/lcd/language/language_fr.h b/Marlin/src/lcd/language/language_fr.h index 0f9a6ea160..13ff8a319b 100644 --- a/Marlin/src/lcd/language/language_fr.h +++ b/Marlin/src/lcd/language/language_fr.h @@ -90,6 +90,7 @@ #define MSG_LEVEL_CORNERS _UxGT("Niveau coins") #define MSG_NEXT_CORNER _UxGT("Coin suivant") #define MSG_EDITING_STOPPED _UxGT("Arrêt édit. maillage") +#define MSG_PROBING_MESH _UxGT("Mesure point") #define MSG_MESH_X _UxGT("Index X") #define MSG_MESH_Y _UxGT("Index Y") #define MSG_MESH_EDIT_Z _UxGT("Valeur Z") @@ -99,8 +100,9 @@ #define MSG_UBL_UNHOMED _UxGT("Origine XYZ requise") #define MSG_UBL_TOOLS _UxGT("Outils UBL") #define MSG_UBL_LEVEL_BED _UxGT("Niveau lit unifié") -#define MSG_LCD_PROBING_MESH _UxGT("Mesure point") #define MSG_LCD_TILTING_MESH _UxGT("Touche point") +#define MSG_M48_TEST _UxGT("Ecart sonde Z M48") +#define MSG_M48_DEVIATION _UxGT("Ecart") #define MSG_IDEX_MENU _UxGT("Mode IDEX") #define MSG_IDEX_MODE_AUTOPARK _UxGT("Auto-Park") #define MSG_IDEX_MODE_DUPLICATE _UxGT("Duplication") @@ -195,7 +197,7 @@ #define MSG_MOVE_Z _UxGT("Déplacer Z") #define MSG_MOVE_E _UxGT("Extrudeur") #define MSG_HOTEND_TOO_COLD _UxGT("Buse trop froide") -#define MSG_MOVE_0025MM _UxGT("Déplacer 0.025mm") +#define MSG_MOVE_Z_DIST _UxGT("Déplacer %smm") #define MSG_MOVE_01MM _UxGT("Déplacer 0.1mm") #define MSG_MOVE_1MM _UxGT("Déplacer 1mm") #define MSG_MOVE_10MM _UxGT("Déplacer 10mm") @@ -314,6 +316,7 @@ #define MSG_SINGLENOZZLE_RETRACT_SPD _UxGT("Vitesse retrait") #define MSG_NOZZLE_STANDBY _UxGT("Attente buse") #define MSG_FILAMENT_SWAP_LENGTH _UxGT("Distance retrait") +#define MSG_FILAMENT_PURGE_LENGTH _UxGT("Longueur de purge") #define MSG_FILAMENTCHANGE _UxGT("Changer filament") #define MSG_FILAMENTLOAD _UxGT("Charger filament") #define MSG_FILAMENTUNLOAD _UxGT("Retrait filament") @@ -486,6 +489,7 @@ #define MSG_VTOOLS_RESET _UxGT("V-tools réinit. ok") #define MSG_START_Z _UxGT("Début Z") #define MSG_END_Z _UxGT(" Fin Z") +#define MSG_GAMES _UxGT("Jeux") #define MSG_BRICKOUT _UxGT("Casse-briques") #define MSG_INVADERS _UxGT("Invaders") #define MSG_SNAKE _UxGT("Sn4k3") diff --git a/Marlin/src/lcd/language/language_gl.h b/Marlin/src/lcd/language/language_gl.h index cc32251bd4..701275a1e2 100644 --- a/Marlin/src/lcd/language/language_gl.h +++ b/Marlin/src/lcd/language/language_gl.h @@ -72,7 +72,7 @@ #define MSG_MOVE_Y _UxGT("Mover Y") #define MSG_MOVE_Z _UxGT("Mover Z") #define MSG_MOVE_E _UxGT("Extrusor") -#define MSG_MOVE_0025MM _UxGT("Mover 0.025mm") +#define MSG_MOVE_Z_DIST _UxGT("Mover %smm") #define MSG_MOVE_01MM _UxGT("Mover 0.1mm") #define MSG_MOVE_1MM _UxGT("Mover 1mm") #define MSG_MOVE_10MM _UxGT("Mover 10mm") diff --git a/Marlin/src/lcd/language/language_hr.h b/Marlin/src/lcd/language/language_hr.h index 39607b56eb..2662e2a272 100644 --- a/Marlin/src/lcd/language/language_hr.h +++ b/Marlin/src/lcd/language/language_hr.h @@ -72,7 +72,7 @@ #define MSG_MOVE_Y _UxGT("Miči Y") #define MSG_MOVE_Z _UxGT("Miči Z") #define MSG_MOVE_E _UxGT("Extruder") -#define MSG_MOVE_0025MM _UxGT("Miči 0.025mm") +#define MSG_MOVE_Z_DIST _UxGT("Miči %smm") #define MSG_MOVE_01MM _UxGT("Miči 0.1mm") #define MSG_MOVE_1MM _UxGT("Miči 1mm") #define MSG_MOVE_10MM _UxGT("Miči 10mm") diff --git a/Marlin/src/lcd/language/language_it.h b/Marlin/src/lcd/language/language_it.h index d7a8e310c0..22abdd9784 100644 --- a/Marlin/src/lcd/language/language_it.h +++ b/Marlin/src/lcd/language/language_it.h @@ -93,6 +93,7 @@ #define MSG_LEVEL_CORNERS _UxGT("Livella spigoli") #define MSG_NEXT_CORNER _UxGT("Prossimo spigolo") #define MSG_EDITING_STOPPED _UxGT("Modif. Mesh Fermata") +#define MSG_PROBING_MESH _UxGT("Punto sondato") #define MSG_MESH_X _UxGT("Indice X") #define MSG_MESH_Y _UxGT("Indice Y") #define MSG_MESH_EDIT_Z _UxGT("Valore di Z") @@ -101,8 +102,9 @@ #define MSG_UBL_UNHOMED _UxGT("Home XYZ prima") #define MSG_UBL_TOOLS _UxGT("Strumenti UBL") #define MSG_UBL_LEVEL_BED _UxGT("Unified Bed Leveling") -#define MSG_LCD_PROBING_MESH _UxGT("Punto sondato") #define MSG_LCD_TILTING_MESH _UxGT("Punto inclinaz.") +#define MSG_M48_TEST _UxGT("Test sonda M48") +#define MSG_M48_DEVIATION _UxGT("Deviazione") #define MSG_IDEX_MENU _UxGT("Modo IDEX") #define MSG_OFFSETS_MENU _UxGT("Strumenti Offsets") #define MSG_IDEX_MODE_AUTOPARK _UxGT("Auto-Park") @@ -197,7 +199,7 @@ #define MSG_MOVE_Z _UxGT("Muovi Z") #define MSG_MOVE_E _UxGT("Estrusore") #define MSG_HOTEND_TOO_COLD _UxGT("Ugello freddo") -#define MSG_MOVE_0025MM _UxGT("Muovi di 0.025mm") +#define MSG_MOVE_Z_DIST _UxGT("Muovi di %smm") #define MSG_MOVE_01MM _UxGT("Muovi di 0.1mm") #define MSG_MOVE_1MM _UxGT("Muovi di 1mm") #define MSG_MOVE_10MM _UxGT("Muovi di 10mm") @@ -310,6 +312,7 @@ #define MSG_CONTROL_RETRACT_RECOVER_SWAPF _UxGT("S UnRet V") #define MSG_AUTORETRACT _UxGT("AutoRitrai") #define MSG_FILAMENT_SWAP_LENGTH _UxGT("Dist. ritrazione") +#define MSG_FILAMENT_PURGE_LENGTH _UxGT("Lunghezza spurgo") #define MSG_TOOL_CHANGE _UxGT("Cambio utensile") #define MSG_TOOL_CHANGE_ZLIFT _UxGT("Risalita Z") #define MSG_SINGLENOZZLE_PRIME_SPD _UxGT("Velocità innesco") @@ -484,6 +487,8 @@ #define MSG_VTOOLS_RESET _UxGT("V-tools ripristin.") #define MSG_START_Z _UxGT("Z inizio") #define MSG_END_Z _UxGT("Z fine") + +#define MSG_GAMES _UxGT("Giochi") #define MSG_BRICKOUT _UxGT("Brickout") #define MSG_INVADERS _UxGT("Invaders") #define MSG_SNAKE _UxGT("Sn4k3") diff --git a/Marlin/src/lcd/language/language_jp-kana.h b/Marlin/src/lcd/language/language_jp-kana.h index fe41a0f156..e1a6b20602 100644 --- a/Marlin/src/lcd/language/language_jp-kana.h +++ b/Marlin/src/lcd/language/language_jp-kana.h @@ -82,7 +82,7 @@ #define MSG_MOVE_Y _UxGT("Yジク イドウ") // "Move Y" #define MSG_MOVE_Z _UxGT("Zジク イドウ") // "Move Z" #define MSG_MOVE_E _UxGT("エクストルーダー") // "Extruder" -#define MSG_MOVE_0025MM _UxGT("0.025mm イドウ") // "Move 0.025mm" +#define MSG_MOVE_Z_DIST _UxGT("%smm イドウ") // "Move 0.025mm" #define MSG_MOVE_01MM _UxGT("0.1mm イドウ") // "Move 0.1mm" #define MSG_MOVE_1MM _UxGT(" 1mm イドウ") // "Move 1mm" #define MSG_MOVE_10MM _UxGT(" 10mm イドウ") // "Move 10mm" diff --git a/Marlin/src/lcd/language/language_ko_KR.h b/Marlin/src/lcd/language/language_ko_KR.h index aca75b257b..86387e2d11 100644 --- a/Marlin/src/lcd/language/language_ko_KR.h +++ b/Marlin/src/lcd/language/language_ko_KR.h @@ -177,7 +177,7 @@ #define MSG_MOVE_Y _UxGT("Move Y") #define MSG_MOVE_Z _UxGT("Move Z") #define MSG_MOVE_E _UxGT("Extruder") -#define MSG_MOVE_0025MM _UxGT("Move 0.025mm") +#define MSG_MOVE_Z_DIST _UxGT("Move %smm") #define MSG_MOVE_01MM _UxGT("Move 0.1mm") #define MSG_MOVE_1MM _UxGT("Move 1mm") #define MSG_MOVE_10MM _UxGT("Move 10mm") diff --git a/Marlin/src/lcd/language/language_nl.h b/Marlin/src/lcd/language/language_nl.h index 8f86d5eaa9..fbf7c78983 100644 --- a/Marlin/src/lcd/language/language_nl.h +++ b/Marlin/src/lcd/language/language_nl.h @@ -80,7 +80,7 @@ #define MSG_MOVE_Y _UxGT("Verplaats Y") #define MSG_MOVE_Z _UxGT("Verplaats Z") #define MSG_MOVE_E _UxGT("Extruder") -#define MSG_MOVE_0025MM _UxGT("Verplaats 0.025mm") +#define MSG_MOVE_Z_DIST _UxGT("Verplaats %smm") #define MSG_MOVE_01MM _UxGT("Verplaats 0.1mm") #define MSG_MOVE_1MM _UxGT("Verplaats 1mm") #define MSG_MOVE_10MM _UxGT("Verplaats 10mm") diff --git a/Marlin/src/lcd/language/language_pl.h b/Marlin/src/lcd/language/language_pl.h index 868f882ebb..92ad95908d 100644 --- a/Marlin/src/lcd/language/language_pl.h +++ b/Marlin/src/lcd/language/language_pl.h @@ -70,7 +70,7 @@ #define MSG_MOVE_Y _UxGT("Przesuń w Y") #define MSG_MOVE_Z _UxGT("Przesuń w Z") #define MSG_MOVE_E _UxGT("Ekstruzja (os E)") -#define MSG_MOVE_0025MM _UxGT("Przesuń co .025mm") +#define MSG_MOVE_Z_DIST _UxGT("Przesuń co %smm") #define MSG_MOVE_01MM _UxGT("Przesuń co .1mm") #define MSG_MOVE_1MM _UxGT("Przesuń co 1mm") #define MSG_MOVE_10MM _UxGT("Przesuń co 10mm") diff --git a/Marlin/src/lcd/language/language_pt-br.h b/Marlin/src/lcd/language/language_pt-br.h index 0becbc03e7..bdb30e080a 100644 --- a/Marlin/src/lcd/language/language_pt-br.h +++ b/Marlin/src/lcd/language/language_pt-br.h @@ -189,7 +189,7 @@ #define MSG_MOVE_Z _UxGT("Mover Z") #define MSG_MOVE_E _UxGT("Mover Extrusor") #define MSG_HOTEND_TOO_COLD _UxGT("Extrus. mto fria") -#define MSG_MOVE_0025MM _UxGT("Mover 0.025mm") +#define MSG_MOVE_Z_DIST _UxGT("Mover %smm") #define MSG_MOVE_01MM _UxGT("Mover 0.1mm") #define MSG_MOVE_1MM _UxGT("Mover 1mm") #define MSG_MOVE_10MM _UxGT("Mover 10mm") diff --git a/Marlin/src/lcd/language/language_pt.h b/Marlin/src/lcd/language/language_pt.h index 936492975d..c6a8367d91 100644 --- a/Marlin/src/lcd/language/language_pt.h +++ b/Marlin/src/lcd/language/language_pt.h @@ -70,7 +70,7 @@ #define MSG_MOVE_Y _UxGT("Mover Y") #define MSG_MOVE_Z _UxGT("Mover Z") #define MSG_MOVE_E _UxGT("Mover Extrusor") -#define MSG_MOVE_0025MM _UxGT("Mover 0.025mm") +#define MSG_MOVE_Z_DIST _UxGT("Mover %smm") #define MSG_MOVE_01MM _UxGT("Mover 0.1mm") #define MSG_MOVE_1MM _UxGT("Mover 1mm") #define MSG_MOVE_10MM _UxGT("Mover 10mm") diff --git a/Marlin/src/lcd/language/language_ru.h b/Marlin/src/lcd/language/language_ru.h index bba2cdad9a..32cac37fb7 100644 --- a/Marlin/src/lcd/language/language_ru.h +++ b/Marlin/src/lcd/language/language_ru.h @@ -36,9 +36,12 @@ #define MSG_BACK _UxGT("Назад") #define MSG_SD_INSERTED _UxGT("Карта вставлена") #define MSG_SD_REMOVED _UxGT("Карта извлечена") +#define MSG_SD_RELEASED _UxGT("SD карта не активна") #define MSG_LCD_ENDSTOPS _UxGT("Эндстопы") // Max length 8 characters #define MSG_LCD_SOFT_ENDSTOPS _UxGT("Прогр. эндстопы") #define MSG_MAIN _UxGT("Меню") +#define MSG_ADVANCED_SETTINGS _UxGT("Другие настройки") +#define MSG_CONFIGURATION _UxGT("Настройки") #define MSG_AUTOSTART _UxGT("Автостарт") #define MSG_DISABLE_STEPPERS _UxGT("Выкл. двигатели") #define MSG_DEBUG_MENU _UxGT("Меню отладки") @@ -78,12 +81,23 @@ #define MSG_LEVEL_CORNERS _UxGT("Выровнять углы") #define MSG_NEXT_CORNER _UxGT("Следующий угол") #define MSG_EDITING_STOPPED _UxGT("Ред. сетки завершено") -#define MSG_USER_MENU _UxGT("Свои комманды") +#define MSG_USER_MENU _UxGT("Свои команды") #define MSG_UBL_DOING_G29 _UxGT("Выполняем G29") #define MSG_UBL_UNHOMED _UxGT("Паркуем сначала XYZ") #define MSG_UBL_TOOLS _UxGT("Утилиты UBL") #define MSG_UBL_LEVEL_BED _UxGT("Калибровка UBL") + +#define MSG_M48_TEST _UxGT("Проверка датчика Z") +#define MSG_M48_DEVIATION _UxGT("Отклонение") + +// TODO: IDEX Menu +#define MSG_OFFSETS_MENU _UxGT("Размещение сопел") + +#define MSG_X_OFFSET _UxGT("2-е сопло X") +#define MSG_Y_OFFSET _UxGT("2-е сопло Y") +#define MSG_Z_OFFSET _UxGT("2-е сопло Z") + #define MSG_UBL_MANUAL_MESH _UxGT("Постр. сетку от руки") #define MSG_UBL_BC_INSERT _UxGT("Пост. шимм и измер.") #define MSG_UBL_BC_INSERT2 _UxGT("Измерение") @@ -168,7 +182,7 @@ #define MSG_MOVE_Y _UxGT("Движение по Y") #define MSG_MOVE_Z _UxGT("Движение по Z") #define MSG_MOVE_E _UxGT("Экструдер") -#define MSG_MOVE_0025MM _UxGT("Движение 0.025мм") +#define MSG_MOVE_Z_DIST _UxGT("Движение %sмм") #define MSG_MOVE_01MM _UxGT("Движение 0.1мм") #define MSG_MOVE_1MM _UxGT("Движение 1мм") #define MSG_MOVE_10MM _UxGT("Движение 10мм") @@ -239,7 +253,7 @@ #define MSG_CONTRAST _UxGT("Контраст LCD") #define MSG_STORE_EEPROM _UxGT("Сохранить настройки") #define MSG_LOAD_EEPROM _UxGT("Загрузить настройки") -#define MSG_RESTORE_FAILSAFE _UxGT("Восстановить настр.") +#define MSG_RESTORE_FAILSAFE _UxGT("Вернуть настройки") #define MSG_INIT_EEPROM _UxGT("Инициализация EEPROM") #define MSG_REFRESH _UxGT("Обновить") #define MSG_WATCH _UxGT("Информационный экран") @@ -266,12 +280,21 @@ #define MSG_CONTROL_RETRACT_RECOVERF _UxGT("Возврат V") #define MSG_CONTROL_RETRACT_RECOVER_SWAPF _UxGT("Возврат смены V") #define MSG_AUTORETRACT _UxGT("Авто Втягивание") + +// TODO: Filament Change Swap / Purge Length + +#define MSG_TOOL_CHANGE _UxGT("Смена сопел") +#define MSG_TOOL_CHANGE_ZLIFT _UxGT("Поднятие по Z") + +// TODO: Singlenozzle, nozzle standby + #define MSG_FILAMENTCHANGE _UxGT("Смена филамента") #define MSG_FILAMENTLOAD _UxGT("Загрузка филамента") #define MSG_FILAMENTUNLOAD _UxGT("Выгрузка филамента") #define MSG_FILAMENTUNLOAD_ALL _UxGT("Выгрузить всё") -#define MSG_INIT_SDCARD _UxGT("Иниц. SD карту") +#define MSG_INIT_SDCARD _UxGT("Активировать SD") #define MSG_CHANGE_SDCARD _UxGT("Сменить SD карту") +#define MSG_RELEASE_SDCARD _UxGT("Деактивировать SD") #define MSG_ZPROBE_OUT _UxGT("Z датчик вне стола") #define MSG_SKEW_FACTOR _UxGT("Фактор наклона") #define MSG_BLTOUCH _UxGT("BLTouch") @@ -279,6 +302,9 @@ #define MSG_BLTOUCH_RESET _UxGT("Сброс BLTouch") #define MSG_BLTOUCH_DEPLOY _UxGT("Установка BLTouch") #define MSG_BLTOUCH_STOW _UxGT("Набивка BLTouch") + +// TODO: TouchMI Probe, Manual deploy/stow + #define MSG_HOME _UxGT("Паркуй") // Used as MSG_HOME " " MSG_X MSG_Y MSG_Z " " MSG_FIRST #define MSG_FIRST _UxGT("первый") #define MSG_ZPROBE_ZOFFSET _UxGT("Смещение Z") @@ -291,10 +317,12 @@ #define MSG_ERR_REDUNDANT_TEMP _UxGT("Ошибка: Избыточная Т") #define MSG_THERMAL_RUNAWAY _UxGT("УБЕГАНИЕ ТЕПЛА") #define MSG_THERMAL_RUNAWAY_BED _UxGT("УБЕГАНИЕ ТЕПЛА СТОЛА") +// TODO: Heated chamber #define MSG_ERR_MAXTEMP _UxGT("Ошибка: Т макс.") #define MSG_ERR_MINTEMP _UxGT("Ошибка: Т мин.") #define MSG_ERR_MAXTEMP_BED _UxGT("Ошибка: Т стола макс") #define MSG_ERR_MINTEMP_BED _UxGT("Ошибка: Т стола мин.") +// TODO: Heated chamber #define MSG_ERR_Z_HOMING MSG_HOME _UxGT(" ") MSG_X MSG_Y _UxGT(" ") MSG_FIRST #define MSG_HALTED _UxGT("ПРИНТЕР ОСТАНОВЛЕН") #define MSG_PLEASE_RESET _UxGT("Сделайте сброс") @@ -303,9 +331,9 @@ #define MSG_SHORT_MINUTE _UxGT("м") // One character only #define MSG_HEATING _UxGT("Нагрев...") #define MSG_COOLING _UxGT("Охлаждение...") -#define MSG_COOLING_COMPLETE _UxGT("Охлаждение выполнено") #define MSG_BED_HEATING _UxGT("Нагрев стола...") #define MSG_BED_COOLING _UxGT("Охлаждение стола...") +// TODO: Heated chamber #define MSG_DELTA_CALIBRATE _UxGT("Калибровка Delta") #define MSG_DELTA_CALIBRATE_X _UxGT("Калибровать X") #define MSG_DELTA_CALIBRATE_Y _UxGT("Калибровать Y") @@ -338,7 +366,7 @@ #define MSG_INFO_COMPLETED_PRINTS _UxGT("Закончено") #define MSG_INFO_PRINT_TIME _UxGT("Общее время печати") #define MSG_INFO_PRINT_LONGEST _UxGT("Наидольшее задание") - #define MSG_INFO_PRINT_FILAMENT _UxGT("Длинна филамента") + #define MSG_INFO_PRINT_FILAMENT _UxGT("Длина филамента") #else #define MSG_INFO_PRINT_COUNT _UxGT("Отпечатков") #define MSG_INFO_COMPLETED_PRINTS _UxGT("Закончено") @@ -348,7 +376,7 @@ #endif #define MSG_INFO_MIN_TEMP _UxGT("Мин. Т") #define MSG_INFO_MAX_TEMP _UxGT("Макс. Т") -#define MSG_INFO_PSU _UxGT("Блок питания") +#define MSG_INFO_PSU _UxGT("БП") #define MSG_DRIVE_STRENGTH _UxGT("Сила привода") #define MSG_DAC_PERCENT _UxGT("Привод %") #define MSG_DAC_EEPROM_WRITE _UxGT("Запись DAC EEPROM") @@ -363,6 +391,16 @@ #define MSG_ERR_PROBING_FAILED _UxGT("Не удалось прощупать") #define MSG_M600_TOO_COLD _UxGT("M600: Низкая Т") +// TODO: MMU2 + +// TODO: Mixing + +#define MSG_GAMES _UxGT("Игры") +#define MSG_BRICKOUT _UxGT("Кирпичи") +#define MSG_INVADERS _UxGT("Вторжение") +#define MSG_SNAKE _UxGT("Змейка") +#define MSG_MAZE _UxGT("Лабиринт") + // // Filament Change screens show up to 3 lines on a 4-line display // ...or up to 2 lines on a 3-line display @@ -398,3 +436,14 @@ #define MSG_FILAMENT_CHANGE_PURGE_1 _UxGT("Выдавливание...") #define MSG_FILAMENT_CHANGE_RESUME_1 _UxGT("Возобновление...") #endif // LCD_HEIGHT < 4 + +#define MSG_TMC_DRIVERS _UxGT("Драйвера TMC") +#define MSG_TMC_CURRENT _UxGT("Текущие настройки") +#define MSG_TMC_HYBRID_THRS _UxGT("Гибридный режим") +#define MSG_TMC_HOMING_THRS _UxGT("Режим без эндстопов") +#define MSG_TMC_STEPPING_MODE _UxGT("Режим шага") +#define MSG_TMC_STEALTH_ENABLED _UxGT("Тихий режим вкл") + +// TODO: Service + +// TODO: Backlash diff --git a/Marlin/src/lcd/language/language_sk.h b/Marlin/src/lcd/language/language_sk.h index 8d028e41cf..0b59137035 100644 --- a/Marlin/src/lcd/language/language_sk.h +++ b/Marlin/src/lcd/language/language_sk.h @@ -101,6 +101,7 @@ #define MSG_LEVEL_CORNERS _UxGT("Vyrovnať rohy") #define MSG_NEXT_CORNER _UxGT("Ďalší roh") #define MSG_EDITING_STOPPED _UxGT("Koniec úprav siete") +#define MSG_PROBING_MESH _UxGT("Skúšam bod") #define MSG_MESH_X _UxGT("Index X") #define MSG_MESH_Y _UxGT("Index Y") #define MSG_MESH_EDIT_Z _UxGT("Hodnota Z") @@ -110,7 +111,6 @@ #define MSG_UBL_UNHOMED _UxGT("Prejdite domov") #define MSG_UBL_TOOLS _UxGT("Nástroje UBL") #define MSG_UBL_LEVEL_BED _UxGT("UBL rovnanie") -#define MSG_LCD_PROBING_MESH _UxGT("Skúšam bod") #define MSG_LCD_TILTING_MESH _UxGT("Vyrovnávam bod") #define MSG_IDEX_MENU _UxGT("IDEX režim") #define MSG_OFFSETS_MENU _UxGT("Ofset nástrojov") @@ -206,7 +206,7 @@ #define MSG_MOVE_Z _UxGT("Posunúť Z") #define MSG_MOVE_E _UxGT("Extrudér") #define MSG_HOTEND_TOO_COLD _UxGT("Hotend je studený") -#define MSG_MOVE_0025MM _UxGT("Posunúť o 0,025mm") +#define MSG_MOVE_Z_DIST _UxGT("Posunúť o %smm") #define MSG_MOVE_01MM _UxGT("Posunúť o 0,1mm") #define MSG_MOVE_1MM _UxGT("Posunúť o 1mm") #define MSG_MOVE_10MM _UxGT("Posunúť o 10mm") diff --git a/Marlin/src/lcd/language/language_tr.h b/Marlin/src/lcd/language/language_tr.h index e8e72b82b1..fcaf1802b0 100644 --- a/Marlin/src/lcd/language/language_tr.h +++ b/Marlin/src/lcd/language/language_tr.h @@ -186,7 +186,7 @@ #define MSG_MOVE_Z _UxGT("Z Hareketi") #define MSG_MOVE_E _UxGT("Ekstruder") #define MSG_HOTEND_TOO_COLD _UxGT("Nozul Çok Soğuk") -#define MSG_MOVE_0025MM _UxGT("0.025mm") +#define MSG_MOVE_Z_DIST _UxGT("%smm") #define MSG_MOVE_01MM _UxGT("0.1mm") #define MSG_MOVE_1MM _UxGT("1mm") #define MSG_MOVE_10MM _UxGT("10mm") diff --git a/Marlin/src/lcd/language/language_uk.h b/Marlin/src/lcd/language/language_uk.h index 90ecf5c693..763a2f559b 100644 --- a/Marlin/src/lcd/language/language_uk.h +++ b/Marlin/src/lcd/language/language_uk.h @@ -72,7 +72,7 @@ #define MSG_MOVE_Y _UxGT("Рух по Y") #define MSG_MOVE_Z _UxGT("Рух по Z") #define MSG_MOVE_E _UxGT("Екструдер") -#define MSG_MOVE_0025MM _UxGT("Рух по 0.025mm") +#define MSG_MOVE_Z_DIST _UxGT("Рух по %smm") #define MSG_MOVE_01MM _UxGT("Рух по 0.1mm") #define MSG_MOVE_1MM _UxGT("Рух по 1mm") #define MSG_MOVE_10MM _UxGT("Рух по 10mm") diff --git a/Marlin/src/lcd/language/language_zh_CN.h b/Marlin/src/lcd/language/language_zh_CN.h index 93835a9dc1..09bc9ff14f 100644 --- a/Marlin/src/lcd/language/language_zh_CN.h +++ b/Marlin/src/lcd/language/language_zh_CN.h @@ -164,7 +164,7 @@ #define MSG_MOVE_Y _UxGT("移动Y") //"Move Y" #define MSG_MOVE_Z _UxGT("移动Z") //"Move Z" #define MSG_MOVE_E _UxGT("挤出机") //"Extruder" -#define MSG_MOVE_0025MM _UxGT("移动 0.025 mm") //"Move 0.025mm" +#define MSG_MOVE_Z_DIST _UxGT("移动 %s mm") //"Move 0.025mm" #define MSG_MOVE_01MM _UxGT("移动 0.1 mm") //"Move 0.1mm" #define MSG_MOVE_1MM _UxGT("移动 1 mm") //"Move 1mm" #define MSG_MOVE_10MM _UxGT("移动 10 mm") //"Move 10mm" diff --git a/Marlin/src/lcd/language/language_zh_TW.h b/Marlin/src/lcd/language/language_zh_TW.h index 90ac8bd573..26984499d1 100644 --- a/Marlin/src/lcd/language/language_zh_TW.h +++ b/Marlin/src/lcd/language/language_zh_TW.h @@ -164,7 +164,7 @@ #define MSG_MOVE_Y _UxGT("移動Y") //"Move Y" #define MSG_MOVE_Z _UxGT("移動Z") //"Move Z" #define MSG_MOVE_E _UxGT("擠出機") //"Extruder" -#define MSG_MOVE_0025MM _UxGT("移動 0.025 mm") //"Move 0.025mm" +#define MSG_MOVE_Z_DIST _UxGT("移動 %s mm") //"Move 0.025mm" #define MSG_MOVE_01MM _UxGT("移動 0.1 mm") //"Move 0.1mm" #define MSG_MOVE_1MM _UxGT("移動 1 mm") //"Move 1mm" #define MSG_MOVE_10MM _UxGT("移動 10 mm") //"Move 10mm" diff --git a/Marlin/src/lcd/menu/game/brickout.cpp b/Marlin/src/lcd/menu/game/brickout.cpp index ad23031360..b13649ca9e 100644 --- a/Marlin/src/lcd/menu/game/brickout.cpp +++ b/Marlin/src/lcd/menu/game/brickout.cpp @@ -28,8 +28,6 @@ #define BRICK_H 5 #define BRICK_TOP MENU_FONT_ASCENT -#define BRICK_ROWS 4 -#define BRICK_COLS 16 #define PADDLE_H 2 #define PADDLE_VEL 3 @@ -42,52 +40,47 @@ #define BRICK_COL(X) ((X) / (BRICK_W)) #define BRICK_ROW(Y) ((Y - (BRICK_TOP)) / (BRICK_H)) -uint8_t balls_left, brick_count; -uint16_t bricks[BRICK_ROWS]; +brickout_data_t &bdat = marlin_game_data.brickout; inline void reset_bricks(const uint16_t v) { - brick_count = (BRICK_COLS) * (BRICK_ROWS); - LOOP_L_N(i, BRICK_ROWS) bricks[i] = v; + bdat.brick_count = (BRICK_COLS) * (BRICK_ROWS); + LOOP_L_N(i, BRICK_ROWS) bdat.bricks[i] = v; } -int8_t paddle_x, hit_dir; -fixed_t ballx, bally, ballh, ballv; - void reset_ball() { constexpr uint8_t ball_dist = 24; - bally = BTOF(PADDLE_Y - ball_dist); - ballv = FTOP(1.3f); - ballh = -FTOP(1.25f); - uint8_t bx = paddle_x + (PADDLE_W) / 2 + ball_dist; - if (bx >= LCD_PIXEL_WIDTH - 10) { bx -= ball_dist * 2; ballh = -ballh; } - ballx = BTOF(bx); - hit_dir = -1; + bdat.bally = BTOF(PADDLE_Y - ball_dist); + bdat.ballv = FTOP(1.3f); + bdat.ballh = -FTOP(1.25f); + uint8_t bx = bdat.paddle_x + (PADDLE_W) / 2 + ball_dist; + if (bx >= LCD_PIXEL_WIDTH - 10) { bx -= ball_dist * 2; bdat.ballh = -bdat.ballh; } + bdat.ballx = BTOF(bx); + bdat.hit_dir = -1; } void BrickoutGame::game_screen() { if (game_frame()) { // Run logic twice for finer resolution // Update Paddle Position - paddle_x = (int8_t)ui.encoderPosition; - paddle_x = constrain(paddle_x, 0, (LCD_PIXEL_WIDTH - (PADDLE_W)) / (PADDLE_VEL)); - ui.encoderPosition = paddle_x; - paddle_x *= (PADDLE_VEL); + bdat.paddle_x = constrain(int8_t(ui.encoderPosition), 0, (LCD_PIXEL_WIDTH - (PADDLE_W)) / (PADDLE_VEL)); + ui.encoderPosition = bdat.paddle_x; + bdat.paddle_x *= (PADDLE_VEL); // Run the ball logic if (game_state) do { // Provisionally update the ball position - const fixed_t newx = ballx + ballh, newy = bally + ballv; // current next position + const fixed_t newx = bdat.ballx + bdat.ballh, newy = bdat.bally + bdat.ballv; // current next position if (!WITHIN(newx, 0, BTOF(LCD_PIXEL_WIDTH - 1))) { // out in x? - ballh = -ballh; _BUZZ(5, 220); // bounce x + bdat.ballh = -bdat.ballh; _BUZZ(5, 220); // bounce x } if (newy < 0) { // out in y? - ballv = -ballv; _BUZZ(5, 280); // bounce v - hit_dir = 1; + bdat.ballv = -bdat.ballv; _BUZZ(5, 280); // bounce v + bdat.hit_dir = 1; } // Did the ball go below the bottom? else if (newy > BTOF(LCD_PIXEL_HEIGHT)) { - BUZZ(500, 75); - if (--balls_left) reset_ball(); else game_state = 0; + _BUZZ(500, 75); + if (--bdat.balls_left) reset_ball(); else game_state = 0; break; // done } @@ -95,42 +88,42 @@ void BrickoutGame::game_screen() { if (WITHIN(newy, BTOF(BRICK_TOP), BTOF(BRICK_BOT))) { const int8_t bit = BRICK_COL(FTOB(newx)), row = BRICK_ROW(FTOB(newy)); const uint16_t mask = _BV(bit); - if (bricks[row] & mask) { + if (bdat.bricks[row] & mask) { // Yes. Remove it! - bricks[row] &= ~mask; + bdat.bricks[row] &= ~mask; // Score! score += BRICK_ROWS - row; // If bricks are gone, go to reset state - if (!--brick_count) game_state = 2; + if (!--bdat.brick_count) game_state = 2; // Bounce the ball cleverly - if ((ballv < 0) == (hit_dir < 0)) { ballv = -ballv; ballh += fixed_t(random(-16, 16)); _BUZZ(5, 880); } - else { ballh = -ballh; ballv += fixed_t(random(-16, 16)); _BUZZ(5, 640); } + if ((bdat.ballv < 0) == (bdat.hit_dir < 0)) { bdat.ballv = -bdat.ballv; bdat.ballh += fixed_t(random(-16, 16)); _BUZZ(5, 880); } + else { bdat.ballh = -bdat.ballh; bdat.ballv += fixed_t(random(-16, 16)); _BUZZ(5, 640); } } } // Is the ball moving down and in paddle range? - else if (ballv > 0 && WITHIN(newy, BTOF(PADDLE_Y), BTOF(PADDLE_Y + PADDLE_H))) { + else if (bdat.ballv > 0 && WITHIN(newy, BTOF(PADDLE_Y), BTOF(PADDLE_Y + PADDLE_H))) { // Ball actually hitting paddle - const int8_t diff = FTOB(newx) - paddle_x; + const int8_t diff = FTOB(newx) - bdat.paddle_x; if (WITHIN(diff, 0, PADDLE_W - 1)) { // Reverse Y direction - ballv = -ballv; _BUZZ(3, 880); - hit_dir = -1; + bdat.ballv = -bdat.ballv; _BUZZ(3, 880); + bdat.hit_dir = -1; // Near edges affects X velocity const bool is_left_edge = (diff <= 1); if (is_left_edge || diff >= PADDLE_W-1 - 1) { - if ((ballh > 0) == is_left_edge) ballh = -ballh; + if ((bdat.ballh > 0) == is_left_edge) bdat.ballh = -bdat.ballh; } else if (diff <= 3) { - ballh += fixed_t(random(-64, 0)); - NOLESS(ballh, BTOF(-2)); - NOMORE(ballh, BTOF(2)); + bdat.ballh += fixed_t(random(-64, 0)); + NOLESS(bdat.ballh, BTOF(-2)); + NOMORE(bdat.ballh, BTOF(2)); } else if (diff >= PADDLE_W-1 - 3) { - ballh += fixed_t(random( 0, 64)); - NOLESS(ballh, BTOF(-2)); - NOMORE(ballh, BTOF(2)); + bdat.ballh += fixed_t(random( 0, 64)); + NOLESS(bdat.ballh, BTOF(-2)); + NOMORE(bdat.ballh, BTOF(2)); } // Paddle hit after clearing the board? Reset the board. @@ -138,7 +131,7 @@ void BrickoutGame::game_screen() { } } - ballx += ballh; bally += ballv; // update with new velocity + bdat.ballx += bdat.ballh; bdat.bally += bdat.ballv; // update with new velocity } while (false); } @@ -151,7 +144,7 @@ void BrickoutGame::game_screen() { const uint8_t yy = y * BRICK_H + BRICK_TOP; if (PAGE_CONTAINS(yy, yy + BRICK_H - 1)) { for (uint8_t x = 0; x < BRICK_COLS; ++x) { - if (TEST(bricks[y], x)) { + if (TEST(bdat.bricks[y], x)) { const uint8_t xx = x * BRICK_W; for (uint8_t v = 0; v < BRICK_H - 1; ++v) if (PAGE_CONTAINS(yy + v, yy + v)) @@ -164,20 +157,20 @@ void BrickoutGame::game_screen() { // Draw paddle if (PAGE_CONTAINS(PADDLE_Y-1, PADDLE_Y)) { - u8g.drawHLine(paddle_x, PADDLE_Y, PADDLE_W); + u8g.drawHLine(bdat.paddle_x, PADDLE_Y, PADDLE_W); #if PADDLE_H > 1 - u8g.drawHLine(paddle_x, PADDLE_Y-1, PADDLE_W); + u8g.drawHLine(bdat.paddle_x, PADDLE_Y-1, PADDLE_W); #if PADDLE_H > 2 - u8g.drawHLine(paddle_x, PADDLE_Y-2, PADDLE_W); + u8g.drawHLine(bdat.paddle_x, PADDLE_Y-2, PADDLE_W); #endif #endif } // Draw ball while game is running if (game_state) { - const uint8_t by = FTOB(bally); + const uint8_t by = FTOB(bdat.bally); if (PAGE_CONTAINS(by, by+1)) - u8g.drawFrame(FTOB(ballx), by, 2, 2); + u8g.drawFrame(FTOB(bdat.ballx), by, 2, 2); } // Or draw GAME OVER else @@ -193,18 +186,20 @@ void BrickoutGame::game_screen() { // Balls Left lcd_moveto(LCD_PIXEL_WIDTH - MENU_FONT_WIDTH * 3, MENU_FONT_ASCENT - 1); PGM_P const ohs = PSTR("ooo\0\0"); - lcd_put_u8str_P(ohs + 3 - balls_left); + lcd_put_u8str_P(ohs + 3 - bdat.balls_left); } // A click always exits this game if (ui.use_click()) exit_game(); } +#define SCREEN_M ((LCD_PIXEL_WIDTH) / 2) + void BrickoutGame::enter_game() { init_game(2, game_screen); // 2 = reset bricks on paddle hit constexpr uint8_t paddle_start = SCREEN_M - (PADDLE_W) / 2; - paddle_x = paddle_start; - balls_left = 3; + bdat.paddle_x = paddle_start; + bdat.balls_left = 3; reset_bricks(0x0000); reset_ball(); ui.encoderPosition = paddle_start / (PADDLE_VEL); diff --git a/Marlin/src/HAL/HAL_STM32F7/HAL_Servo_STM32F7.h b/Marlin/src/lcd/menu/game/brickout.h similarity index 66% rename from Marlin/src/HAL/HAL_STM32F7/HAL_Servo_STM32F7.h rename to Marlin/src/lcd/menu/game/brickout.h index 6ff0bfc489..9037e53830 100644 --- a/Marlin/src/HAL/HAL_STM32F7/HAL_Servo_STM32F7.h +++ b/Marlin/src/lcd/menu/game/brickout.h @@ -4,7 +4,6 @@ * * Based on Sprinter and grbl. * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm - * Copyright (c) 2017 Victor Perez * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -22,16 +21,18 @@ */ #pragma once -#include <../../libraries/Servo/src/Servo.h> +#include "types.h" -// Inherit and expand on the official library -class libServo : public Servo { -public: - int8_t attach(const int pin); - int8_t attach(const int pin, const int min, const int max); - void move(const int value); -private: - uint16_t min_ticks; - uint16_t max_ticks; - uint8_t servoIndex; // index into the channel data for this servo -}; +#define BRICK_ROWS 4 +#define BRICK_COLS 16 + +typedef struct { + uint8_t balls_left, brick_count; + uint16_t bricks[BRICK_ROWS]; + int8_t paddle_x, hit_dir; + fixed_t ballx, bally, ballh, ballv; +} brickout_data_t; + +class BrickoutGame : MarlinGame { public: static void enter_game(), game_screen(); }; + +extern BrickoutGame brickout; diff --git a/Marlin/src/lcd/menu/game/game.cpp b/Marlin/src/lcd/menu/game/game.cpp index 9393552437..1f1982615a 100644 --- a/Marlin/src/lcd/menu/game/game.cpp +++ b/Marlin/src/lcd/menu/game/game.cpp @@ -30,6 +30,8 @@ int MarlinGame::score; uint8_t MarlinGame::game_state; millis_t MarlinGame::next_frame; +MarlinGameData marlin_game_data; + bool MarlinGame::game_frame() { static int8_t slew; if (ui.first_page) slew = 2; @@ -56,7 +58,6 @@ void MarlinGame::draw_game_over() { void MarlinGame::init_game(const uint8_t init_state, const screenFunc_t screen) { score = 0; game_state = init_state; - ui.encoder_direction_normal(); ui.goto_screen(screen); ui.defer_status_screen(); } diff --git a/Marlin/src/lcd/menu/game/game.h b/Marlin/src/lcd/menu/game/game.h index 398f06af35..f168ccec79 100644 --- a/Marlin/src/lcd/menu/game/game.h +++ b/Marlin/src/lcd/menu/game/game.h @@ -28,51 +28,43 @@ //#define MUTE_GAMES -#ifdef MUTE_GAMES +#if ENABLED(MUTE_GAMES) || !HAS_BUZZER #define _BUZZ(D,F) NOOP #else #define _BUZZ(D,F) BUZZ(D,F) #endif -// Simple 8:8 fixed-point -typedef int16_t fixed_t; -#define FTOP(F) fixed_t((F)*256.0f) -#define PTOF(P) (float(P)*(1.0f/256.0f)) -#define BTOF(X) (fixed_t(X)<<8) -#define FTOB(X) int8_t(fixed_t(X)>>8) - -#define SCREEN_M ((LCD_PIXEL_WIDTH) / 2) - #if HAS_GAME_MENU void menu_game(); #endif -class MarlinGame { -protected: - static int score; - static uint8_t game_state; - static millis_t next_frame; - - static bool game_frame(); - static void draw_game_over(); - static void exit_game(); -public: - static void init_game(const uint8_t init_state, const screenFunc_t screen); -}; - #if ENABLED(MARLIN_BRICKOUT) - class BrickoutGame : MarlinGame { public: static void enter_game(); static void game_screen(); }; - extern BrickoutGame brickout; + #include "brickout.h" #endif #if ENABLED(MARLIN_INVADERS) - class InvadersGame : MarlinGame { public: static void enter_game(); static void game_screen(); }; - extern InvadersGame invaders; -#endif -#if ENABLED(MARLIN_SNAKE) - class SnakeGame : MarlinGame { public: static void enter_game(); static void game_screen(); }; - extern SnakeGame snake; + #include "invaders.h" #endif #if ENABLED(MARLIN_MAZE) - class MazeGame : MarlinGame { public: static void enter_game(); static void game_screen(); }; - extern MazeGame maze; + #include "maze.h" #endif +#if ENABLED(MARLIN_SNAKE) + #include "snake.h" +#endif + +// Pool game data to save SRAM +union MarlinGameData { + #if ENABLED(MARLIN_BRICKOUT) + brickout_data_t brickout; + #endif + #if ENABLED(MARLIN_INVADERS) + invaders_data_t invaders; + #endif + #if ENABLED(MARLIN_SNAKE) + snake_data_t snake; + #endif + #if ENABLED(MARLIN_MAZE) + maze_data_t maze; + #endif +}; + +extern MarlinGameData marlin_game_data; diff --git a/Marlin/src/lcd/menu/game/invaders.cpp b/Marlin/src/lcd/menu/game/invaders.cpp index 55a1e4a849..c183867eac 100644 --- a/Marlin/src/lcd/menu/game/invaders.cpp +++ b/Marlin/src/lcd/menu/game/invaders.cpp @@ -26,6 +26,28 @@ #include "game.h" +#define CANNON_W 11 +#define CANNON_H 8 +#define CANNON_VEL 4 +#define CANNON_Y (LCD_PIXEL_HEIGHT - 1 - CANNON_H) + +#define INVADER_VEL 3 + +#define INVADER_TOP MENU_FONT_ASCENT +#define INVADERS_WIDE ((INVADER_COL_W) * (INVADER_COLS)) +#define INVADERS_HIGH ((INVADER_ROW_H) * (INVADER_ROWS)) + +#define UFO_H 5 +#define UFO_W 13 + +#define LASER_H 4 +#define SHOT_H 3 +#define EXPL_W 11 +#define LIFE_W 8 +#define LIFE_H 5 + +#define INVADER_RIGHT ((INVADER_COLS) * (INVADER_COL_W)) + // 11x8 const unsigned char invader[3][2][16] PROGMEM = { { { B00000110,B00000000, @@ -120,20 +142,6 @@ const unsigned char ufo[] PROGMEM = { B01111111,B11110000 }; -#define INVASION_SIZE 3 - -#if INVASION_SIZE == 3 - #define INVADER_COLS 5 -#elif INVASION_SIZE == 4 - #define INVADER_COLS 6 -#else - #define INVADER_COLS 8 - #undef INVASION_SIZE - #define INVASION_SIZE 5 -#endif - -#define INVADER_ROWS INVASION_SIZE - constexpr uint8_t inv_type[] = { #if INVADER_ROWS == 5 0, 1, 1, 2, 2 @@ -146,107 +154,74 @@ constexpr uint8_t inv_type[] = { #endif }; -#define INVADER_RIGHT ((INVADER_COLS) * (COL_W)) +invaders_data_t &idat = marlin_game_data.invaders; -#define CANNON_W 11 -#define CANNON_H 8 -#define CANNON_VEL 4 -#define CANNON_Y (LCD_PIXEL_HEIGHT - 1 - CANNON_H) - -#define COL_W 14 -#define INVADER_H 8 -#define ROW_H (INVADER_H + 2) -#define INVADER_VEL 3 - -#define INVADER_TOP MENU_FONT_ASCENT -#define INVADERS_WIDE ((COL_W) * (INVADER_COLS)) -#define INVADERS_HIGH ((ROW_H) * (INVADER_ROWS)) - -#define UFO_H 5 -#define UFO_W 13 - -#define LASER_H 4 -#define SHOT_H 3 -#define EXPL_W 11 -#define LIFE_W 8 -#define LIFE_H 5 - -#define INVADER_COL(X) ((X - invaders_x) / (COL_W)) -#define INVADER_ROW(Y) ((Y - invaders_y + 2) / (ROW_H)) - -#define INV_X_LEFT(C,T) (invaders_x + (C) * (COL_W) + inv_off[T]) +#define INV_X_LEFT(C,T) (idat.pos.x + (C) * (INVADER_COL_W) + inv_off[T]) #define INV_X_CTR(C,T) (INV_X_LEFT(C,T) + inv_wide[T] / 2) -#define INV_Y_BOT(R) (invaders_y + (R + 1) * (ROW_H) - 2) +#define INV_Y_BOT(R) (idat.pos.y + (R + 1) * (INVADER_ROW_H) - 2) -typedef struct { int8_t x, y, v; } laser_t; - -uint8_t cannons_left; -int8_t cannon_x; -laser_t explod, laser, bullet[10]; constexpr uint8_t inv_off[] = { 2, 1, 0 }, inv_wide[] = { 8, 11, 12 }; -int8_t invaders_x, invaders_y, invaders_dir, leftmost, rightmost, botmost; -uint8_t invader_count, quit_count, bugs[INVADER_ROWS], shooters[(INVADER_ROWS) * (INVADER_COLS)]; inline void update_invader_data() { uint8_t inv_mask = 0; // Get a list of all active invaders uint8_t sc = 0; LOOP_L_N(y, INVADER_ROWS) { - uint8_t m = bugs[y]; - if (m) botmost = y + 1; + uint8_t m = idat.bugs[y]; + if (m) idat.botmost = y + 1; inv_mask |= m; for (uint8_t x = 0; x < INVADER_COLS; ++x) - if (TEST(m, x)) shooters[sc++] = (y << 4) | x; + if (TEST(m, x)) idat.shooters[sc++] = (y << 4) | x; } - leftmost = 0; - LOOP_L_N(i, INVADER_COLS) { if (TEST(inv_mask, i)) break; leftmost -= COL_W; } - rightmost = LCD_PIXEL_WIDTH - (INVADERS_WIDE); - for (uint8_t i = INVADER_COLS; i--;) { if (TEST(inv_mask, i)) break; rightmost += COL_W; } - if (invader_count == 2) invaders_dir = invaders_dir > 0 ? INVADER_VEL + 1 : -(INVADER_VEL + 1); + idat.leftmost = 0; + LOOP_L_N(i, INVADER_COLS) { if (TEST(inv_mask, i)) break; idat.leftmost -= INVADER_COL_W; } + idat.rightmost = LCD_PIXEL_WIDTH - (INVADERS_WIDE); + for (uint8_t i = INVADER_COLS; i--;) { if (TEST(inv_mask, i)) break; idat.rightmost += INVADER_COL_W; } + if (idat.count == 2) idat.dir = idat.dir > 0 ? INVADER_VEL + 1 : -(INVADER_VEL + 1); } inline void reset_bullets() { - LOOP_L_N(i, COUNT(bullet)) bullet[i].v = 0; + LOOP_L_N(i, COUNT(idat.bullet)) idat.bullet[i].v = 0; } inline void reset_invaders() { - invaders_x = 0; invaders_y = INVADER_TOP; - invaders_dir = INVADER_VEL; - invader_count = (INVADER_COLS) * (INVADER_ROWS); - LOOP_L_N(i, INVADER_ROWS) bugs[i] = _BV(INVADER_COLS) - 1; + idat.pos.x = 0; idat.pos.y = INVADER_TOP; + idat.dir = INVADER_VEL; + idat.count = (INVADER_COLS) * (INVADER_ROWS); + LOOP_L_N(i, INVADER_ROWS) idat.bugs[i] = _BV(INVADER_COLS) - 1; update_invader_data(); reset_bullets(); } -int8_t ufox, ufov; + inline void spawn_ufo() { - ufov = random(0, 2) ? 1 : -1; - ufox = ufov > 0 ? -(UFO_W) : LCD_PIXEL_WIDTH - 1; + idat.ufov = random(0, 2) ? 1 : -1; + idat.ufox = idat.ufov > 0 ? -(UFO_W) : LCD_PIXEL_WIDTH - 1; } inline void reset_player() { - cannon_x = 0; + idat.cannon_x = 0; ui.encoderPosition = 0; } inline void fire_cannon() { - laser.x = cannon_x + CANNON_W / 2; - laser.y = LCD_PIXEL_HEIGHT - CANNON_H - (LASER_H); - laser.v = -(LASER_H); + idat.laser.x = idat.cannon_x + CANNON_W / 2; + idat.laser.y = LCD_PIXEL_HEIGHT - CANNON_H - (LASER_H); + idat.laser.v = -(LASER_H); } inline void explode(const int8_t x, const int8_t y, const int8_t v=4) { - explod.x = x - (EXPL_W) / 2; - explod.y = y; - explod.v = v; + idat.explod.x = x - (EXPL_W) / 2; + idat.explod.y = y; + idat.explod.v = v; } inline void kill_cannon(uint8_t &game_state, const uint8_t st) { reset_bullets(); - explode(cannon_x + (CANNON_W) / 2, CANNON_Y, 6); + explode(idat.cannon_x + (CANNON_W) / 2, CANNON_Y, 6); _BUZZ(1000, 10); - if (--cannons_left) { - laser.v = 0; + if (--idat.cannons_left) { + idat.laser.v = 0; game_state = st; reset_player(); } @@ -255,59 +230,55 @@ inline void kill_cannon(uint8_t &game_state, const uint8_t st) { } void InvadersGame::game_screen() { - static bool game_blink; - ui.refresh(LCDVIEW_CALL_NO_REDRAW); // Call as often as possible // Run game logic once per full screen if (ui.first_page) { // Update Cannon Position - int16_t ep = int16_t(ui.encoderPosition); - ep = constrain(ep, 0, (LCD_PIXEL_WIDTH - (CANNON_W)) / (CANNON_VEL)); + int16_t ep = constrain(int16_t(ui.encoderPosition), 0, (LCD_PIXEL_WIDTH - (CANNON_W)) / (CANNON_VEL)); ui.encoderPosition = ep; ep *= (CANNON_VEL); - if (ep > cannon_x) { cannon_x += CANNON_VEL - 1; if (ep - cannon_x < 2) cannon_x = ep; } - if (ep < cannon_x) { cannon_x -= CANNON_VEL - 1; if (cannon_x - ep < 2) cannon_x = ep; } + if (ep > idat.cannon_x) { idat.cannon_x += CANNON_VEL - 1; if (ep - idat.cannon_x < 2) idat.cannon_x = ep; } + if (ep < idat.cannon_x) { idat.cannon_x -= CANNON_VEL - 1; if (idat.cannon_x - ep < 2) idat.cannon_x = ep; } // Run the game logic if (game_state) do { // Move the UFO, if any - if (ufov) { ufox += ufov; if (!WITHIN(ufox, -(UFO_W), LCD_PIXEL_WIDTH - 1)) ufov = 0; } + if (idat.ufov) { idat.ufox += idat.ufov; if (!WITHIN(idat.ufox, -(UFO_W), LCD_PIXEL_WIDTH - 1)) idat.ufov = 0; } if (game_state > 1) { if (--game_state == 2) { reset_invaders(); } else if (game_state == 100) { game_state = 1; } break; } - static uint8_t blink_count; - const bool did_blink = (++blink_count > invader_count >> 1); + const bool did_blink = (++idat.blink_count > idat.count >> 1); if (did_blink) { - game_blink = !game_blink; - blink_count = 0; + idat.game_blink = !idat.game_blink; + idat.blink_count = 0; } - if (invader_count && did_blink) { - const int8_t newx = invaders_x + invaders_dir; - if (!WITHIN(newx, leftmost, rightmost)) { // Invaders reached the edge? - invaders_dir *= -1; // Invaders change direction - invaders_y += (ROW_H) / 2; // Invaders move down - invaders_x -= invaders_dir; // ...and only move down this time. - if (invaders_y + botmost * (ROW_H) - 2 >= CANNON_Y) // Invaders reached the bottom? - kill_cannon(game_state, 20); // Kill the cannon. Reset invaders. + if (idat.count && did_blink) { + const int8_t newx = idat.pos.x + idat.dir; + if (!WITHIN(newx, idat.leftmost, idat.rightmost)) { // Invaders reached the edge? + idat.dir *= -1; // Invaders change direction + idat.pos.y += (INVADER_ROW_H) / 2; // Invaders move down + idat.pos.x -= idat.dir; // ...and only move down this time. + if (idat.pos.y + idat.botmost * (INVADER_ROW_H) - 2 >= CANNON_Y) // Invaders reached the bottom? + kill_cannon(game_state, 20); // Kill the cannon. Reset invaders. } - invaders_x += invaders_dir; // Invaders take one step left/right + idat.pos.x += idat.dir; // Invaders take one step left/right // Randomly shoot if invaders are listed - if (invader_count && !random(0, 20)) { + if (idat.count && !random(0, 20)) { // Find a free bullet laser_t *b = nullptr; - LOOP_L_N(i, COUNT(bullet)) if (!bullet[i].v) { b = &bullet[i]; break; } + LOOP_L_N(i, COUNT(idat.bullet)) if (!idat.bullet[i].v) { b = &idat.bullet[i]; break; } if (b) { // Pick a random shooter and update the bullet //SERIAL_ECHOLNPGM("free bullet found"); - const uint8_t inv = shooters[random(0, invader_count + 1)], col = inv & 0x0F, row = inv >> 4, type = inv_type[row]; + const uint8_t inv = idat.shooters[random(0, idat.count + 1)], col = inv & 0x0F, row = inv >> 4, type = inv_type[row]; b->x = INV_X_CTR(col, type); b->y = INV_Y_BOT(row); b->v = 2 + random(0, 2); @@ -316,34 +287,34 @@ void InvadersGame::game_screen() { } // Update the laser position - if (laser.v) { - laser.y += laser.v; - if (laser.y < 0) laser.v = 0; + if (idat.laser.v) { + idat.laser.y += idat.laser.v; + if (idat.laser.y < 0) idat.laser.v = 0; } // Did the laser collide with an invader? - if (laser.v && WITHIN(laser.y, invaders_y, invaders_y + INVADERS_HIGH - 1)) { - const int8_t col = INVADER_COL(laser.x); + if (idat.laser.v && WITHIN(idat.laser.y, idat.pos.y, idat.pos.y + INVADERS_HIGH - 1)) { + const int8_t col = idat.laser_col(); if (WITHIN(col, 0, INVADER_COLS - 1)) { - const int8_t row = INVADER_ROW(laser.y); + const int8_t row = idat.laser_row(); if (WITHIN(row, 0, INVADER_ROWS - 1)) { const uint8_t mask = _BV(col); - if (bugs[row] & mask) { + if (idat.bugs[row] & mask) { const uint8_t type = inv_type[row]; const int8_t invx = INV_X_LEFT(col, type); - if (WITHIN(laser.x, invx, invx + inv_wide[type] - 1)) { + if (WITHIN(idat.laser.x, invx, invx + inv_wide[type] - 1)) { // Turn off laser - laser.v = 0; + idat.laser.v = 0; // Remove the invader! - bugs[row] &= ~mask; + idat.bugs[row] &= ~mask; // Score! score += INVADER_ROWS - row; // Explode sound! _BUZZ(40, 10); // Explosion bitmap! - explode(invx + inv_wide[type] / 2, invaders_y + row * (ROW_H)); + explode(invx + inv_wide[type] / 2, idat.pos.y + row * (INVADER_ROW_H)); // If invaders are gone, go to reset invaders state - if (--invader_count) update_invader_data(); else { game_state = 20; reset_bullets(); } + if (--idat.count) update_invader_data(); else { game_state = 20; reset_bullets(); } } // laser x hit } // invader exists } // good row @@ -351,31 +322,31 @@ void InvadersGame::game_screen() { } // laser in invader zone // Handle alien bullets - LOOP_L_N(s, COUNT(bullet)) { - laser_t *b = &bullet[s]; + LOOP_L_N(s, COUNT(idat.bullet)) { + laser_t *b = &idat.bullet[s]; if (b->v) { // Update alien bullet position b->y += b->v; if (b->y >= LCD_PIXEL_HEIGHT) b->v = 0; // Offscreen - else if (b->y >= CANNON_Y && WITHIN(b->x, cannon_x, cannon_x + CANNON_W - 1)) + else if (b->y >= CANNON_Y && WITHIN(b->x, idat.cannon_x, idat.cannon_x + CANNON_W - 1)) kill_cannon(game_state, 120); // Hit the cannon } } // Randomly spawn a UFO - if (!ufov && !random(0,500)) spawn_ufo(); + if (!idat.ufov && !random(0,500)) spawn_ufo(); // Did the laser hit a ufo? - if (laser.v && ufov && laser.y < UFO_H + 2 && WITHIN(laser.x, ufox, ufox + UFO_W - 1)) { + if (idat.laser.v && idat.ufov && idat.laser.y < UFO_H + 2 && WITHIN(idat.laser.x, idat.ufox, idat.ufox + UFO_W - 1)) { // Turn off laser and UFO - laser.v = ufov = 0; + idat.laser.v = idat.ufov = 0; // Score! score += 10; // Explode! _BUZZ(40, 10); // Explosion bitmap - explode(ufox + (UFO_W) / 2, 1); + explode(idat.ufox + (UFO_W) / 2, 1); } } while (false); @@ -383,59 +354,59 @@ void InvadersGame::game_screen() { } // Click-and-hold to abort - if (ui.button_pressed()) --quit_count; else quit_count = 10; + if (ui.button_pressed()) --idat.quit_count; else idat.quit_count = 10; // Click to fire or exit if (ui.use_click()) { if (!game_state) - quit_count = 0; - else if (game_state == 1 && !laser.v) + idat.quit_count = 0; + else if (game_state == 1 && !idat.laser.v) fire_cannon(); } - if (!quit_count) exit_game(); + if (!idat.quit_count) exit_game(); u8g.setColorIndex(1); // Draw invaders - if (PAGE_CONTAINS(invaders_y, invaders_y + botmost * (ROW_H) - 2 - 1)) { - int8_t yy = invaders_y; + if (PAGE_CONTAINS(idat.pos.y, idat.pos.y + idat.botmost * (INVADER_ROW_H) - 2 - 1)) { + int8_t yy = idat.pos.y; for (uint8_t y = 0; y < INVADER_ROWS; ++y) { const uint8_t type = inv_type[y]; if (PAGE_CONTAINS(yy, yy + INVADER_H - 1)) { - int8_t xx = invaders_x; + int8_t xx = idat.pos.x; for (uint8_t x = 0; x < INVADER_COLS; ++x) { - if (TEST(bugs[y], x)) - u8g.drawBitmapP(xx, yy, 2, INVADER_H, invader[type][game_blink]); - xx += COL_W; + if (TEST(idat.bugs[y], x)) + u8g.drawBitmapP(xx, yy, 2, INVADER_H, invader[type][idat.game_blink]); + xx += INVADER_COL_W; } } - yy += ROW_H; + yy += INVADER_ROW_H; } } // Draw UFO - if (ufov && PAGE_UNDER(UFO_H + 2)) - u8g.drawBitmapP(ufox, 2, 2, UFO_H, ufo); + if (idat.ufov && PAGE_UNDER(UFO_H + 2)) + u8g.drawBitmapP(idat.ufox, 2, 2, UFO_H, ufo); // Draw cannon if (game_state && PAGE_CONTAINS(CANNON_Y, CANNON_Y + CANNON_H - 1) && (game_state < 2 || (game_state & 0x02))) - u8g.drawBitmapP(cannon_x, CANNON_Y, 2, CANNON_H, cannon); + u8g.drawBitmapP(idat.cannon_x, CANNON_Y, 2, CANNON_H, cannon); // Draw laser - if (laser.v && PAGE_CONTAINS(laser.y, laser.y + LASER_H - 1)) - u8g.drawVLine(laser.x, laser.y, LASER_H); + if (idat.laser.v && PAGE_CONTAINS(idat.laser.y, idat.laser.y + LASER_H - 1)) + u8g.drawVLine(idat.laser.x, idat.laser.y, LASER_H); // Draw invader bullets - LOOP_L_N (i, COUNT(bullet)) { - if (bullet[i].v && PAGE_CONTAINS(bullet[i].y - (SHOT_H - 1), bullet[i].y)) - u8g.drawVLine(bullet[i].x, bullet[i].y - (SHOT_H - 1), SHOT_H); + LOOP_L_N (i, COUNT(idat.bullet)) { + if (idat.bullet[i].v && PAGE_CONTAINS(idat.bullet[i].y - (SHOT_H - 1), idat.bullet[i].y)) + u8g.drawVLine(idat.bullet[i].x, idat.bullet[i].y - (SHOT_H - 1), SHOT_H); } // Draw explosion - if (explod.v && PAGE_CONTAINS(explod.y, explod.y + 7 - 1)) { - u8g.drawBitmapP(explod.x, explod.y, 2, 7, explosion); - --explod.v; + if (idat.explod.v && PAGE_CONTAINS(idat.explod.y, idat.explod.y + 7 - 1)) { + u8g.drawBitmapP(idat.explod.x, idat.explod.y, 2, 7, explosion); + --idat.explod.v; } // Blink GAME OVER when game is over @@ -449,8 +420,8 @@ void InvadersGame::game_screen() { lcd_put_int(score); // Draw lives - if (cannons_left) - for (uint8_t i = 1; i <= cannons_left; ++i) + if (idat.cannons_left) + for (uint8_t i = 1; i <= idat.cannons_left; ++i) u8g.drawBitmapP(LCD_PIXEL_WIDTH - i * (LIFE_W), 6 - (LIFE_H), 1, LIFE_H, life); } @@ -458,9 +429,9 @@ void InvadersGame::game_screen() { void InvadersGame::enter_game() { init_game(20, game_screen); // countdown to reset invaders - cannons_left = 3; - quit_count = 10; - laser.v = 0; + idat.cannons_left = 3; + idat.quit_count = 10; + idat.laser.v = 0; reset_invaders(); reset_player(); } diff --git a/Marlin/src/lcd/menu/game/invaders.h b/Marlin/src/lcd/menu/game/invaders.h new file mode 100644 index 0000000000..f04e91da64 --- /dev/null +++ b/Marlin/src/lcd/menu/game/invaders.h @@ -0,0 +1,62 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +#include "types.h" + +#define INVASION_SIZE 3 + +#if INVASION_SIZE == 3 + #define INVADER_COLS 5 +#elif INVASION_SIZE == 4 + #define INVADER_COLS 6 +#else + #define INVADER_COLS 8 + #undef INVASION_SIZE + #define INVASION_SIZE 5 +#endif + +#define INVADER_ROWS INVASION_SIZE + +#define INVADER_COL_W 14 +#define INVADER_H 8 +#define INVADER_ROW_H (INVADER_H + 2) + +typedef struct { int8_t x, y, v; } laser_t; + +typedef struct { + pos_t pos; + uint8_t cannons_left; + int8_t cannon_x; + laser_t bullet[10], laser, explod; + int8_t dir, leftmost, rightmost, botmost; + uint8_t count, quit_count, blink_count; + uint8_t bugs[INVADER_ROWS], shooters[(INVADER_ROWS) * (INVADER_COLS)]; + int8_t ufox, ufov; + bool game_blink; + int8_t laser_col() { return ((laser.x - pos.x) / (INVADER_COL_W)); }; + int8_t laser_row() { return ((laser.y - pos.y + 2) / (INVADER_ROW_H)); }; +} invaders_data_t; + +class InvadersGame : MarlinGame { public: static void enter_game(), game_screen(); }; + +extern InvadersGame invaders; diff --git a/Marlin/src/lcd/menu/game/maze.cpp b/Marlin/src/lcd/menu/game/maze.cpp index 60b5939c6e..bb07ce0d64 100644 --- a/Marlin/src/lcd/menu/game/maze.cpp +++ b/Marlin/src/lcd/menu/game/maze.cpp @@ -89,12 +89,12 @@ void MazeGame::game_screen() { // for (uint8_t n = 0; n < head_ind; ++n) { // const pos_t &p = maze_walls[n], &q = maze_walls[n + 1]; // if (p.x == q.x) { - // const int8_t y1 = GAMEY(MIN(p.y, q.y)), y2 = GAMEY(MAX(p.y, q.y)); + // const int8_t y1 = GAMEY(_MIN(p.y, q.y)), y2 = GAMEY(_MAX(p.y, q.y)); // if (PAGE_CONTAINS(y1, y2)) // u8g.drawVLine(GAMEX(p.x), y1, y2 - y1 + 1); // } // else if (PAGE_CONTAINS(GAMEY(p.y), GAMEY(p.y))) { - // const int8_t x1 = GAMEX(MIN(p.x, q.x)), x2 = GAMEX(MAX(p.x, q.x)); + // const int8_t x1 = GAMEX(_MIN(p.x, q.x)), x2 = GAMEX(_MAX(p.x, q.x)); // u8g.drawHLine(x1, GAMEY(p.y), x2 - x1 + 1); // } // } diff --git a/Marlin/src/lcd/menu/game/maze.h b/Marlin/src/lcd/menu/game/maze.h new file mode 100644 index 0000000000..5d7fff66af --- /dev/null +++ b/Marlin/src/lcd/menu/game/maze.h @@ -0,0 +1,30 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +#include "types.h" + +typedef struct { pos_t pos; } maze_data_t; + +class MazeGame : MarlinGame { public: static void enter_game(), game_screen(); }; + +extern MazeGame maze; diff --git a/Marlin/src/lcd/menu/game/snake.cpp b/Marlin/src/lcd/menu/game/snake.cpp index 80e9cabaf2..f12a8b3959 100644 --- a/Marlin/src/lcd/menu/game/snake.cpp +++ b/Marlin/src/lcd/menu/game/snake.cpp @@ -65,20 +65,12 @@ constexpr fixed_t snakev = FTOP(0.20); -int8_t snake_dir, // NESW - foodx, foody, food_cnt, - old_encoder; -fixed_t snakex, snakey; - -// Up to 50 lines, then you win! -typedef struct { int8_t x, y; } pos_t; -uint8_t head_ind; -pos_t snake_tail[50]; +snake_data_t &sdat = marlin_game_data.snake; // Remove the first pixel from the tail. // If needed, shift out the first segment. void shorten_tail() { - pos_t &p = snake_tail[0], &q = snake_tail[1]; + pos_t &p = sdat.snake_tail[0], &q = sdat.snake_tail[1]; bool shift = false; if (p.x == q.x) { // Vertical line @@ -91,21 +83,21 @@ void shorten_tail() { shift = p.x == q.x; } if (shift) { - head_ind--; - for (uint8_t i = 0; i <= head_ind; ++i) - snake_tail[i] = snake_tail[i + 1]; + sdat.head_ind--; + for (uint8_t i = 0; i <= sdat.head_ind; ++i) + sdat.snake_tail[i] = sdat.snake_tail[i + 1]; } } // The food is on a line inline bool food_on_line() { - for (uint8_t n = 0; n < head_ind; ++n) { - pos_t &p = snake_tail[n], &q = snake_tail[n + 1]; + for (uint8_t n = 0; n < sdat.head_ind; ++n) { + pos_t &p = sdat.snake_tail[n], &q = sdat.snake_tail[n + 1]; if (p.x == q.x) { - if ((foodx == p.x - 1 || foodx == p.x) && WITHIN(foody, MIN(p.y, q.y), MAX(p.y, q.y))) + if ((sdat.foodx == p.x - 1 || sdat.foodx == p.x) && WITHIN(sdat.foody, _MIN(p.y, q.y), _MAX(p.y, q.y))) return true; } - else if ((foody == p.y - 1 || foody == p.y) && WITHIN(foodx, MIN(p.x, q.x), MAX(p.x, q.x))) + else if ((sdat.foody == p.y - 1 || sdat.foody == p.y) && WITHIN(sdat.foodx, _MIN(p.x, q.x), _MAX(p.x, q.x))) return true; } return false; @@ -114,71 +106,71 @@ inline bool food_on_line() { // Add a new food blob void food_reset() { do { - foodx = random(0, GAME_W); - foody = random(0, GAME_H); + sdat.foodx = random(0, GAME_W); + sdat.foody = random(0, GAME_H); } while (food_on_line()); } // Turn the snake cw or ccw inline void turn_snake(const bool cw) { - snake_dir += cw ? 1 : -1; - snake_dir &= 0x03; - head_ind++; - snake_tail[head_ind].x = FTOB(snakex); - snake_tail[head_ind].y = FTOB(snakey); + sdat.snake_dir += cw ? 1 : -1; + sdat.snake_dir &= 0x03; + sdat.head_ind++; + sdat.snake_tail[sdat.head_ind].x = FTOB(sdat.snakex); + sdat.snake_tail[sdat.head_ind].y = FTOB(sdat.snakey); } // Reset the snake for a new game void snake_reset() { // Init the head and velocity - snakex = BTOF(1); - snakey = BTOF(GAME_H / 2); + sdat.snakex = BTOF(1); + sdat.snakey = BTOF(GAME_H / 2); //snakev = FTOP(0.25); // Init the tail with a cw turn - snake_dir = 0; - head_ind = 0; - snake_tail[0].x = 0; - snake_tail[0].y = GAME_H / 2; + sdat.snake_dir = 0; + sdat.head_ind = 0; + sdat.snake_tail[0].x = 0; + sdat.snake_tail[0].y = GAME_H / 2; turn_snake(true); // Clear food flag - food_cnt = 5; + sdat.food_cnt = 5; // Clear the controls ui.encoderPosition = 0; - old_encoder = 0; + sdat.old_encoder = 0; } // Check if head segment overlaps another bool snake_overlap() { // 4 lines must exist before a collision is possible - if (head_ind < 4) return false; + if (sdat.head_ind < 4) return false; // Is the last segment crossing any others? - const pos_t &h1 = snake_tail[head_ind - 1], &h2 = snake_tail[head_ind]; + const pos_t &h1 = sdat.snake_tail[sdat.head_ind - 1], &h2 = sdat.snake_tail[sdat.head_ind]; // VERTICAL head segment? if (h1.x == h2.x) { // Loop from oldest to segment two away from head - for (uint8_t n = 0; n < head_ind - 2; ++n) { + for (uint8_t n = 0; n < sdat.head_ind - 2; ++n) { // Segment p to q - const pos_t &p = snake_tail[n], &q = snake_tail[n + 1]; + const pos_t &p = sdat.snake_tail[n], &q = sdat.snake_tail[n + 1]; if (p.x != q.x) { // Crossing horizontal segment - if (WITHIN(h1.x, MIN(p.x, q.x), MAX(p.x, q.x)) && (h1.y <= p.y) == (h2.y >= p.y)) return true; + if (WITHIN(h1.x, _MIN(p.x, q.x), _MAX(p.x, q.x)) && (h1.y <= p.y) == (h2.y >= p.y)) return true; } // Overlapping vertical segment - else if (h1.x == p.x && MIN(h1.y, h2.y) <= MAX(p.y, q.y) && MAX(h1.y, h2.y) >= MIN(p.y, q.y)) return true; + else if (h1.x == p.x && _MIN(h1.y, h2.y) <= _MAX(p.y, q.y) && _MAX(h1.y, h2.y) >= _MIN(p.y, q.y)) return true; } } else { // Loop from oldest to segment two away from head - for (uint8_t n = 0; n < head_ind - 2; ++n) { + for (uint8_t n = 0; n < sdat.head_ind - 2; ++n) { // Segment p to q - const pos_t &p = snake_tail[n], &q = snake_tail[n + 1]; + const pos_t &p = sdat.snake_tail[n], &q = sdat.snake_tail[n + 1]; if (p.y != q.y) { // Crossing vertical segment - if (WITHIN(h1.y, MIN(p.y, q.y), MAX(p.y, q.y)) && (h1.x <= p.x) == (h2.x >= p.x)) return true; + if (WITHIN(h1.y, _MIN(p.y, q.y), _MAX(p.y, q.y)) && (h1.x <= p.x) == (h2.x >= p.x)) return true; } // Overlapping horizontal segment - else if (h1.y == p.y && MIN(h1.x, h2.x) <= MAX(p.x, q.x) && MAX(h1.x, h2.x) >= MIN(p.x, q.x)) return true; + else if (h1.y == p.y && _MIN(h1.x, h2.x) <= _MAX(p.x, q.x) && _MAX(h1.x, h2.x) >= _MIN(p.x, q.x)) return true; } } return false; @@ -189,14 +181,14 @@ void SnakeGame::game_screen() { if (game_frame()) do { // Run logic twice for finer resolution // Move the snake's head one unit in the current direction - const int8_t oldx = FTOB(snakex), oldy = FTOB(snakey); - switch (snake_dir) { - case 0: snakey -= snakev; break; - case 1: snakex += snakev; break; - case 2: snakey += snakev; break; - case 3: snakex -= snakev; break; + const int8_t oldx = FTOB(sdat.snakex), oldy = FTOB(sdat.snakey); + switch (sdat.snake_dir) { + case 0: sdat.snakey -= snakev; break; + case 1: sdat.snakex += snakev; break; + case 2: sdat.snakey += snakev; break; + case 3: sdat.snakex -= snakev; break; } - const int8_t x = FTOB(snakex), y = FTOB(snakey); + const int8_t x = FTOB(sdat.snakex), y = FTOB(sdat.snakey); // If movement took place... if (oldx != x || oldy != y) { @@ -207,17 +199,17 @@ void SnakeGame::game_screen() { break; // ...out of do-while } - snake_tail[head_ind].x = x; - snake_tail[head_ind].y = y; + sdat.snake_tail[sdat.head_ind].x = x; + sdat.snake_tail[sdat.head_ind].y = y; // Change snake direction if set - const int8_t enc = int8_t(ui.encoderPosition), diff = enc - old_encoder; + const int8_t enc = int8_t(ui.encoderPosition), diff = enc - sdat.old_encoder; if (diff) { - old_encoder = enc; + sdat.old_encoder = enc; turn_snake(diff > 0); } - if (food_cnt) --food_cnt; else shorten_tail(); + if (sdat.food_cnt) --sdat.food_cnt; else shorten_tail(); // Did the snake collide with itself or go out of bounds? if (snake_overlap()) { @@ -225,11 +217,11 @@ void SnakeGame::game_screen() { _BUZZ(400, 40); // Bzzzt! } // Is the snake at the food? - else if (x == foodx && y == foody) { + else if (x == sdat.foodx && y == sdat.foody) { _BUZZ(5, 220); _BUZZ(5, 280); score++; - food_cnt = 2; + sdat.food_cnt = 2; food_reset(); } } @@ -251,15 +243,15 @@ void SnakeGame::game_screen() { #if SNAKE_WH < 2 // At this scale just draw a line - for (uint8_t n = 0; n < head_ind; ++n) { - const pos_t &p = snake_tail[n], &q = snake_tail[n + 1]; + for (uint8_t n = 0; n < sdat.head_ind; ++n) { + const pos_t &p = sdat.snake_tail[n], &q = sdat.snake_tail[n + 1]; if (p.x == q.x) { - const int8_t y1 = GAMEY(MIN(p.y, q.y)), y2 = GAMEY(MAX(p.y, q.y)); + const int8_t y1 = GAMEY(_MIN(p.y, q.y)), y2 = GAMEY(_MAX(p.y, q.y)); if (PAGE_CONTAINS(y1, y2)) u8g.drawVLine(GAMEX(p.x), y1, y2 - y1 + 1); } else if (PAGE_CONTAINS(GAMEY(p.y), GAMEY(p.y))) { - const int8_t x1 = GAMEX(MIN(p.x, q.x)), x2 = GAMEX(MAX(p.x, q.x)); + const int8_t x1 = GAMEX(_MIN(p.x, q.x)), x2 = GAMEX(_MAX(p.x, q.x)); u8g.drawHLine(x1, GAMEY(p.y), x2 - x1 + 1); } } @@ -267,17 +259,17 @@ void SnakeGame::game_screen() { #elif SNAKE_WH == 2 // At this scale draw two lines - for (uint8_t n = 0; n < head_ind; ++n) { - const pos_t &p = snake_tail[n], &q = snake_tail[n + 1]; + for (uint8_t n = 0; n < sdat.head_ind; ++n) { + const pos_t &p = sdat.snake_tail[n], &q = sdat.snake_tail[n + 1]; if (p.x == q.x) { - const int8_t y1 = GAMEY(MIN(p.y, q.y)), y2 = GAMEY(MAX(p.y, q.y)); + const int8_t y1 = GAMEY(_MIN(p.y, q.y)), y2 = GAMEY(_MAX(p.y, q.y)); if (PAGE_CONTAINS(y1, y2 + 1)) u8g.drawFrame(GAMEX(p.x), y1, 2, y2 - y1 + 1 + 1); } else { const int8_t py = GAMEY(p.y); if (PAGE_CONTAINS(py, py + 1)) { - const int8_t x1 = GAMEX(MIN(p.x, q.x)), x2 = GAMEX(MAX(p.x, q.x)); + const int8_t x1 = GAMEX(_MIN(p.x, q.x)), x2 = GAMEX(_MAX(p.x, q.x)); u8g.drawFrame(x1, py, x2 - x1 + 1 + 1, 2); } } @@ -286,10 +278,10 @@ void SnakeGame::game_screen() { #else // Draw a series of boxes - for (uint8_t n = 0; n < head_ind; ++n) { - const pos_t &p = snake_tail[n], &q = snake_tail[n + 1]; + for (uint8_t n = 0; n < sdat.head_ind; ++n) { + const pos_t &p = sdat.snake_tail[n], &q = sdat.snake_tail[n + 1]; if (p.x == q.x) { - const int8_t y1 = MIN(p.y, q.y), y2 = MAX(p.y, q.y); + const int8_t y1 = _MIN(p.y, q.y), y2 = _MAX(p.y, q.y); if (PAGE_CONTAINS(GAMEY(y1), GAMEY(y2) + SNAKE_SIZ - 1)) { for (int8_t i = y1; i <= y2; ++i) { const int8_t y = GAMEY(i); @@ -301,7 +293,7 @@ void SnakeGame::game_screen() { else { const int8_t py = GAMEY(p.y); if (PAGE_CONTAINS(py, py + SNAKE_SIZ - 1)) { - const int8_t x1 = MIN(p.x, q.x), x2 = MAX(p.x, q.x); + const int8_t x1 = _MIN(p.x, q.x), x2 = _MAX(p.x, q.x); for (int8_t i = x1; i <= x2; ++i) u8g.drawBox(GAMEX(i), py, SNAKE_SIZ, SNAKE_SIZ); } @@ -311,9 +303,9 @@ void SnakeGame::game_screen() { #endif // Draw food - const int8_t fy = GAMEY(foody); + const int8_t fy = GAMEY(sdat.foody); if (PAGE_CONTAINS(fy, fy + FOOD_WH - 1)) { - const int8_t fx = GAMEX(foodx); + const int8_t fx = GAMEX(sdat.foodx); u8g.drawFrame(fx, fy, FOOD_WH, FOOD_WH); if (FOOD_WH == 5) u8g.drawPixel(fx + 2, fy + 2); } diff --git a/Marlin/src/lcd/menu/game/snake.h b/Marlin/src/lcd/menu/game/snake.h new file mode 100644 index 0000000000..ec8524f2ef --- /dev/null +++ b/Marlin/src/lcd/menu/game/snake.h @@ -0,0 +1,38 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +#include "types.h" + +typedef struct { + int8_t snake_dir, // NESW + foodx, foody, + food_cnt, + old_encoder; + pos_t snake_tail[50]; + fixed_t snakex, snakey; + uint8_t head_ind; +} snake_data_t; + +class SnakeGame : MarlinGame { public: static void enter_game(), game_screen(); }; + +extern SnakeGame snake; diff --git a/Marlin/src/HAL/HAL_STM32F4/SanityCheck.h b/Marlin/src/lcd/menu/game/types.h similarity index 61% rename from Marlin/src/HAL/HAL_STM32F4/SanityCheck.h rename to Marlin/src/lcd/menu/game/types.h index e9eb8fa826..872d034dca 100644 --- a/Marlin/src/HAL/HAL_STM32F4/SanityCheck.h +++ b/Marlin/src/lcd/menu/game/types.h @@ -21,17 +21,26 @@ */ #pragma once -/** - * Test STM32F4-specific configuration values for errors at compile-time. - */ -//#if ENABLED(SPINDLE_LASER_PWM) && !(SPINDLE_LASER_PWM_PIN == 4 || SPINDLE_LASER_PWM_PIN == 6 || SPINDLE_LASER_PWM_PIN == 11) -// #error "SPINDLE_LASER_PWM_PIN must use SERVO0, SERVO1 or SERVO3 connector" -//#endif +#include -#if ENABLED(EMERGENCY_PARSER) - #error "EMERGENCY_PARSER is not yet implemented for STM32F4. Disable EMERGENCY_PARSER to continue." -#endif +typedef struct { int8_t x, y; } pos_t; -#if ENABLED(FAST_PWM_FAN) - #error "FAST_PWM_FAN is not yet implemented for this platform." -#endif +// Simple 8:8 fixed-point +typedef int16_t fixed_t; +#define FTOP(F) fixed_t((F)*256.0f) +#define PTOF(P) (float(P)*(1.0f/256.0f)) +#define BTOF(X) (fixed_t(X)<<8) +#define FTOB(X) int8_t(fixed_t(X)>>8) + +class MarlinGame { +protected: + static int score; + static uint8_t game_state; + static millis_t next_frame; + + static bool game_frame(); + static void draw_game_over(); + static void exit_game(); +public: + static void init_game(const uint8_t init_state, const screenFunc_t screen); +}; diff --git a/Marlin/src/lcd/menu/menu.cpp b/Marlin/src/lcd/menu/menu.cpp index ac41a72292..9bea6c1352 100644 --- a/Marlin/src/lcd/menu/menu.cpp +++ b/Marlin/src/lcd/menu/menu.cpp @@ -31,7 +31,9 @@ #include "../../module/printcounter.h" #include "../../gcode/queue.h" #include "../../sd/cardreader.h" -#include "../../libs/buzzer.h" +#if HAS_BUZZER + #include "../../libs/buzzer.h" +#endif #if ENABLED(EEPROM_SETTINGS) #include "../../module/configuration_store.h" @@ -130,7 +132,6 @@ void MenuItem_gcode::action(PGM_P const pgcode) { queue.inject_P(pgcode); } * MenuItem_int3::action_edit(PSTR(MSG_SPEED), &feedrate_percentage, 10, 999) */ void MenuItemBase::edit(strfunc_t strfunc, loadfunc_t loadfunc) { - ui.encoder_direction_normal(); if (int16_t(ui.encoderPosition) < 0) ui.encoderPosition = 0; if (int16_t(ui.encoderPosition) > maxEditValue) ui.encoderPosition = maxEditValue; if (ui.should_draw()) @@ -157,15 +158,16 @@ void MenuItemBase::init(PGM_P const el, void * const ev, const int32_t minv, con #define DEFINE_MENU_EDIT_ITEM(NAME) template class TMenuItem +DEFINE_MENU_EDIT_ITEM(percent); // 100% right-justified DEFINE_MENU_EDIT_ITEM(int3); // 123, -12 right-justified DEFINE_MENU_EDIT_ITEM(int4); // 1234, -123 right-justified DEFINE_MENU_EDIT_ITEM(int8); // 123, -12 right-justified DEFINE_MENU_EDIT_ITEM(uint8); // 123 right-justified -DEFINE_MENU_EDIT_ITEM(uint16_3); // 123, -12 right-justified +DEFINE_MENU_EDIT_ITEM(uint16_3); // 123 right-justified DEFINE_MENU_EDIT_ITEM(uint16_4); // 1234 right-justified DEFINE_MENU_EDIT_ITEM(uint16_5); // 12345 right-justified DEFINE_MENU_EDIT_ITEM(float3); // 123 right-justified -DEFINE_MENU_EDIT_ITEM(float52); // 123.45 +DEFINE_MENU_EDIT_ITEM(float52); // _2.34, 12.34, -2.34 or 123.45, -23.45 DEFINE_MENU_EDIT_ITEM(float43); // 1.234 DEFINE_MENU_EDIT_ITEM(float5); // 12345 right-justified DEFINE_MENU_EDIT_ITEM(float5_25); // 12345 right-justified (25 increment) @@ -204,6 +206,10 @@ void MarlinUI::goto_screen(screenFunc_t screen, const uint16_t encoder/*=0*/, co lcd_z_fade_height = planner.z_fade_height; #endif + #if ENABLED(LCD_SET_PROGRESS_MANUALLY) + progress_reset(); + #endif + #if BOTH(DOUBLECLICK_FOR_Z_BABYSTEPPING, BABYSTEPPING) static millis_t doubleclick_expire_ms = 0; // Going to menu_main from status screen? Remember first click time. @@ -272,7 +278,11 @@ void MarlinUI::goto_screen(screenFunc_t screen, const uint16_t encoder/*=0*/, co drawing_screen = false; #endif - set_ui_selection(false); + #if HAS_LCD_MENU + encoder_direction_normal(); + #endif + + set_selection(false); } } @@ -326,7 +336,7 @@ void scroll_screen(const uint8_t limit, const bool is_menu) { screen_changed = false; } if (screen_items > 0 && encoderLine >= screen_items - limit) { - encoderLine = MAX(0, screen_items - limit); + encoderLine = _MAX(0, screen_items - limit); ui.encoderPosition = encoderLine * (ENCODER_STEPS_PER_MENU_ITEM); } if (is_menu) { @@ -338,13 +348,15 @@ void scroll_screen(const uint8_t limit, const bool is_menu) { encoderTopLine = encoderLine; } -void MarlinUI::completion_feedback(const bool good/*=true*/) { - if (good) { - BUZZ(100, 659); - BUZZ(100, 698); +#if HAS_BUZZER + void MarlinUI::completion_feedback(const bool good/*=true*/) { + if (good) { + BUZZ(100, 659); + BUZZ(100, 698); + } + else BUZZ(20, 440); } - else BUZZ(20, 440); -} +#endif #if HAS_LINE_TO_Z @@ -367,7 +379,6 @@ void MarlinUI::completion_feedback(const bool good/*=true*/) { #else constexpr bool do_probe = true; #endif - ui.encoder_direction_normal(); if (ui.encoderPosition) { const int16_t babystep_increment = int16_t(ui.encoderPosition) * (BABYSTEP_MULTIPLICATOR); ui.encoderPosition = 0; @@ -426,8 +437,18 @@ void MarlinUI::completion_feedback(const bool good/*=true*/) { #endif #if ENABLED(EEPROM_SETTINGS) - void lcd_store_settings() { ui.completion_feedback(settings.save()); } - void lcd_load_settings() { ui.completion_feedback(settings.load()); } + void lcd_store_settings() { + const bool saved = settings.save(); + #if HAS_BUZZER + ui.completion_feedback(saved); + #endif + } + void lcd_load_settings() { + const bool loaded = settings.load(); + #if HAS_BUZZER + ui.completion_feedback(loaded); + #endif + } #endif void _lcd_draw_homing() { @@ -444,14 +465,17 @@ void _lcd_draw_homing() { // // Selection screen presents a prompt and two options // -bool ui_selection; // = false -void set_ui_selection(const bool sel) { ui_selection = sel; } -void do_select_screen(PGM_P const yes, PGM_P const no, selectFunc_t yesFunc, selectFunc_t noFunc, PGM_P const pref, const char * const string/*=nullptr*/, PGM_P const suff/*=nullptr*/) { - if (ui.encoderPosition) { - ui_selection = int16_t(ui.encoderPosition) > 0; - ui.encoderPosition = 0; +bool MarlinUI::selection; // = false +bool MarlinUI::update_selection() { + encoder_direction_select(); + if (encoderPosition) { + selection = int16_t(encoderPosition) > 0; + encoderPosition = 0; } - const bool got_click = ui.use_click(); + return selection; +} +void do_select_screen(PGM_P const yes, PGM_P const no, selectFunc_t yesFunc, selectFunc_t noFunc, PGM_P const pref, const char * const string/*=nullptr*/, PGM_P const suff/*=nullptr*/) { + const bool ui_selection = ui.update_selection(), got_click = ui.use_click(); if (got_click || ui.should_draw()) { draw_select_screen(yes, no, ui_selection, pref, string, suff); if (got_click) { ui_selection ? yesFunc() : noFunc(); } diff --git a/Marlin/src/lcd/menu/menu.h b/Marlin/src/lcd/menu/menu.h index 52f428db2f..781c87615d 100644 --- a/Marlin/src/lcd/menu/menu.h +++ b/Marlin/src/lcd/menu/menu.h @@ -59,7 +59,7 @@ DECLARE_MENU_EDIT_TYPE(float, float52, ftostr42_52, 100 ); // _2. DECLARE_MENU_EDIT_TYPE(float, float43, ftostr43sign, 1000 ); // 1.234 DECLARE_MENU_EDIT_TYPE(float, float5, ftostr5rj, 0.01f ); // 12345 right-justified DECLARE_MENU_EDIT_TYPE(float, float5_25, ftostr5rj, 0.04f ); // 12345 right-justified (25 increment) -DECLARE_MENU_EDIT_TYPE(float, float51, ftostr51rj, 10 ); // _1234.5 right-justified +DECLARE_MENU_EDIT_TYPE(float, float51, ftostr51rj, 10 ); // 1234.5 right-justified DECLARE_MENU_EDIT_TYPE(float, float51sign, ftostr51sign, 10 ); // +1234.5 DECLARE_MENU_EDIT_TYPE(float, float52sign, ftostr52sign, 100 ); // +123.45 DECLARE_MENU_EDIT_TYPE(uint32_t, long5, ftostr5rj, 0.01f ); // 12345 right-justified @@ -71,7 +71,6 @@ DECLARE_MENU_EDIT_TYPE(uint32_t, long5_25, ftostr5rj, 0.04f ); // 123 typedef void (*selectFunc_t)(); void draw_select_screen(PGM_P const yes, PGM_P const no, const bool yesno, PGM_P const pref, const char * const string, PGM_P const suff); -void set_ui_selection(const bool sel); void do_select_screen(PGM_P const yes, PGM_P const no, selectFunc_t yesFunc, selectFunc_t noFunc, PGM_P const pref, const char * const string=nullptr, PGM_P const suff=nullptr); inline void do_select_screen_yn(selectFunc_t yesFunc, selectFunc_t noFunc, PGM_P const pref, const char * const string=nullptr, PGM_P const suff=nullptr) { do_select_screen(PSTR(MSG_YES), PSTR(MSG_NO), yesFunc, noFunc, pref, string, suff); @@ -192,8 +191,8 @@ class TMenuItem : MenuItemBase { public: static void action_edit(PGM_P const pstr, type_t * const ptr, const type_t minValue, const type_t maxValue, const screenFunc_t callback=nullptr, const bool live=false) { // Make sure minv and maxv fit within int16_t - const int32_t minv = MAX(scale(minValue), INT_MIN), - maxv = MIN(scale(maxValue), INT_MAX); + const int32_t minv = _MAX(scale(minValue), INT_MIN), + maxv = _MIN(scale(maxValue), INT_MAX); init(pstr, ptr, minv, maxv - minv, scale(*ptr) - minv, edit, callback, live); } static void edit() { MenuItemBase::edit(to_string, load); } diff --git a/Marlin/src/lcd/menu/menu_advanced.cpp b/Marlin/src/lcd/menu/menu_advanced.cpp index 2dc865c3b4..2dc66cee4a 100644 --- a/Marlin/src/lcd/menu/menu_advanced.cpp +++ b/Marlin/src/lcd/menu/menu_advanced.cpp @@ -554,7 +554,7 @@ void menu_backlash(); #else MENU_MULTIPLIER_ITEM_EDIT(float52sign, MSG_VC_JERK, &planner.max_jerk[C_AXIS], 0.1f, 990); #endif - #if DISABLED(JUNCTION_DEVIATION) || DISABLED(LIN_ADVANCE) + #if !BOTH(JUNCTION_DEVIATION, LIN_ADVANCE) EDIT_JERK(E); #endif #endif @@ -603,7 +603,12 @@ void menu_backlash(); static void lcd_init_eeprom_confirm() { do_select_screen( PSTR(MSG_BUTTON_INIT), PSTR(MSG_BUTTON_CANCEL), - []{ ui.completion_feedback(settings.init_eeprom()); }, + []{ + const bool inited = settings.init_eeprom(); + #if HAS_BUZZER + ui.completion_feedback(inited); + #endif + }, ui.goto_previous_screen, PSTR(MSG_INIT_EEPROM), nullptr, PSTR("?") ); @@ -698,8 +703,11 @@ void menu_advanced_settings() { // // Toggle the SD Firmware Update state in EEPROM // - const bool new_state = !settings.sd_update_status(); - ui.completion_feedback(settings.set_sd_update_status(new_state)); + const bool new_state = !settings.sd_update_status(), + didset = settings.set_sd_update_status(new_state); + #if HAS_BUZZER + ui.completion_feedback(didset); + #endif ui.return_to_status(); if (new_state) LCD_MESSAGEPGM(MSG_RESET_PRINTER); else ui.reset_status(); }); diff --git a/Marlin/src/lcd/menu/menu_bed_corners.cpp b/Marlin/src/lcd/menu/menu_bed_corners.cpp index 10d0e5d7cd..a559a68527 100644 --- a/Marlin/src/lcd/menu/menu_bed_corners.cpp +++ b/Marlin/src/lcd/menu/menu_bed_corners.cpp @@ -111,7 +111,7 @@ static inline void _lcd_level_bed_corners_homing() { if (all_axes_homed()) { bed_corner = 0; ui.goto_screen(menu_level_bed_corners); - set_ui_selection(true); + ui.set_selection(true); _lcd_goto_next_corner(); } } diff --git a/Marlin/src/lcd/menu/menu_bed_leveling.cpp b/Marlin/src/lcd/menu/menu_bed_leveling.cpp index cd98f21a65..3f1f746af1 100644 --- a/Marlin/src/lcd/menu/menu_bed_leveling.cpp +++ b/Marlin/src/lcd/menu/menu_bed_leveling.cpp @@ -77,7 +77,9 @@ ui.synchronize(PSTR(MSG_LEVEL_BED_DONE)); #endif ui.goto_previous_screen_no_defer(); - ui.completion_feedback(); + #if HAS_BUZZER + ui.completion_feedback(); + #endif } if (ui.should_draw()) draw_menu_item_static(LCD_HEIGHT >= 4 ? 1 : 0, PSTR(MSG_LEVEL_BED_DONE)); ui.refresh(LCDVIEW_CALL_REDRAW_NEXT); @@ -89,7 +91,6 @@ // Step 7: Get the Z coordinate, click goes to the next point or exits // void _lcd_level_bed_get_z() { - ui.encoder_direction_normal(); if (ui.use_click()) { @@ -239,7 +240,7 @@ void menu_bed_leveling() { const bool is_homed = all_axes_known(); // Auto Home if not using manual probing - #if DISABLED(PROBE_MANUALLY, MESH_BED_LEVELING) + #if NONE(PROBE_MANUALLY, MESH_BED_LEVELING) if (!is_homed) MENU_ITEM(gcode, MSG_AUTO_HOME, PSTR("G28")); #endif diff --git a/Marlin/src/lcd/menu/menu_configuration.cpp b/Marlin/src/lcd/menu/menu_configuration.cpp index fbf4ba0761..29ab1a1716 100644 --- a/Marlin/src/lcd/menu/menu_configuration.cpp +++ b/Marlin/src/lcd/menu/menu_configuration.cpp @@ -50,11 +50,15 @@ #define HAS_DEBUG_MENU ENABLED(LCD_PROGRESS_BAR_TEST) void menu_advanced_settings(); -void menu_delta_calibrate(); +#if EITHER(DELTA_CALIBRATION_MENU, DELTA_AUTO_CALIBRATION) + void menu_delta_calibrate(); +#endif static void lcd_factory_settings() { settings.reset(); - ui.completion_feedback(); + #if HAS_BUZZER + ui.completion_feedback(); + #endif } #if ENABLED(LCD_PROGRESS_BAR_TEST) @@ -62,7 +66,6 @@ static void lcd_factory_settings() { #include "../lcdprint.h" static void progress_bar_test() { - ui.encoder_direction_normal(); static int8_t bar_percent = 0; if (ui.use_click()) { ui.goto_previous_screen(); @@ -70,7 +73,7 @@ static void lcd_factory_settings() { return; } bar_percent += (int8_t)ui.encoderPosition; - bar_percent = constrain(bar_percent, 0, 100); + LIMIT(bar_percent, 0, 100); ui.encoderPosition = 0; draw_menu_item_static(0, PSTR(MSG_PROGRESS_BAR_TEST), true, true); lcd_moveto((LCD_WIDTH) / 2 - 2, LCD_HEIGHT - 2); @@ -109,7 +112,15 @@ static void lcd_factory_settings() { START_MENU(); MENU_BACK(MSG_CONFIGURATION); #if ENABLED(TOOLCHANGE_FILAMENT_SWAP) - MENU_ITEM_EDIT(float3, MSG_FILAMENT_SWAP_LENGTH, &toolchange_settings.swap_length, 0, 200); + static constexpr float max_extrude = + #if ENABLED(PREVENT_LENGTHY_EXTRUDE) + EXTRUDE_MAXLENGTH + #else + 500 + #endif + ; + MENU_ITEM_EDIT(float3, MSG_FILAMENT_SWAP_LENGTH, &toolchange_settings.swap_length, 0, max_extrude); + MENU_ITEM_EDIT(float3, MSG_FILAMENT_PURGE_LENGTH, &toolchange_settings.extra_prime, 0, max_extrude); MENU_MULTIPLIER_ITEM_EDIT(int4, MSG_SINGLENOZZLE_RETRACT_SPD, &toolchange_settings.retract_speed, 10, 5400); MENU_MULTIPLIER_ITEM_EDIT(int4, MSG_SINGLENOZZLE_PRIME_SPD, &toolchange_settings.prime_speed, 10, 5400); #endif @@ -283,27 +294,27 @@ static void lcd_factory_settings() { void _menu_configuration_preheat_settings(const uint8_t material) { #if HOTENDS > 5 - #define MINTEMP_ALL MIN(HEATER_0_MINTEMP, HEATER_1_MINTEMP, HEATER_2_MINTEMP, HEATER_3_MINTEMP, HEATER_4_MINTEMP, HEATER_5_MINTEMP) - #define MAXTEMP_ALL MAX(HEATER_0_MAXTEMP, HEATER_1_MAXTEMP, HEATER_2_MAXTEMP, HEATER_3_MAXTEMP, HEATER_4_MAXTEMP, HEATER_5_MAXTEMP) + #define MINTEMP_ALL _MIN(HEATER_0_MINTEMP, HEATER_1_MINTEMP, HEATER_2_MINTEMP, HEATER_3_MINTEMP, HEATER_4_MINTEMP, HEATER_5_MINTEMP) + #define MAXTEMP_ALL _MAX(HEATER_0_MAXTEMP, HEATER_1_MAXTEMP, HEATER_2_MAXTEMP, HEATER_3_MAXTEMP, HEATER_4_MAXTEMP, HEATER_5_MAXTEMP) #elif HOTENDS > 4 - #define MINTEMP_ALL MIN(HEATER_0_MINTEMP, HEATER_1_MINTEMP, HEATER_2_MINTEMP, HEATER_3_MINTEMP, HEATER_4_MINTEMP) - #define MAXTEMP_ALL MAX(HEATER_0_MAXTEMP, HEATER_1_MAXTEMP, HEATER_2_MAXTEMP, HEATER_3_MAXTEMP, HEATER_4_MAXTEMP) + #define MINTEMP_ALL _MIN(HEATER_0_MINTEMP, HEATER_1_MINTEMP, HEATER_2_MINTEMP, HEATER_3_MINTEMP, HEATER_4_MINTEMP) + #define MAXTEMP_ALL _MAX(HEATER_0_MAXTEMP, HEATER_1_MAXTEMP, HEATER_2_MAXTEMP, HEATER_3_MAXTEMP, HEATER_4_MAXTEMP) #elif HOTENDS > 3 - #define MINTEMP_ALL MIN(HEATER_0_MINTEMP, HEATER_1_MINTEMP, HEATER_2_MINTEMP, HEATER_3_MINTEMP) - #define MAXTEMP_ALL MAX(HEATER_0_MAXTEMP, HEATER_1_MAXTEMP, HEATER_2_MAXTEMP, HEATER_3_MAXTEMP) + #define MINTEMP_ALL _MIN(HEATER_0_MINTEMP, HEATER_1_MINTEMP, HEATER_2_MINTEMP, HEATER_3_MINTEMP) + #define MAXTEMP_ALL _MAX(HEATER_0_MAXTEMP, HEATER_1_MAXTEMP, HEATER_2_MAXTEMP, HEATER_3_MAXTEMP) #elif HOTENDS > 2 - #define MINTEMP_ALL MIN(HEATER_0_MINTEMP, HEATER_1_MINTEMP, HEATER_2_MINTEMP) - #define MAXTEMP_ALL MAX(HEATER_0_MAXTEMP, HEATER_1_MAXTEMP, HEATER_2_MAXTEMP) + #define MINTEMP_ALL _MIN(HEATER_0_MINTEMP, HEATER_1_MINTEMP, HEATER_2_MINTEMP) + #define MAXTEMP_ALL _MAX(HEATER_0_MAXTEMP, HEATER_1_MAXTEMP, HEATER_2_MAXTEMP) #elif HOTENDS > 1 - #define MINTEMP_ALL MIN(HEATER_0_MINTEMP, HEATER_1_MINTEMP) - #define MAXTEMP_ALL MAX(HEATER_0_MAXTEMP, HEATER_1_MAXTEMP) + #define MINTEMP_ALL _MIN(HEATER_0_MINTEMP, HEATER_1_MINTEMP) + #define MAXTEMP_ALL _MAX(HEATER_0_MAXTEMP, HEATER_1_MAXTEMP) #else #define MINTEMP_ALL HEATER_0_MINTEMP #define MAXTEMP_ALL HEATER_0_MAXTEMP #endif START_MENU(); MENU_BACK(MSG_CONFIGURATION); - MENU_ITEM_EDIT(uint8, MSG_FAN_SPEED, &ui.preheat_fan_speed[material], 0, 255); + MENU_ITEM_EDIT(percent, MSG_FAN_SPEED, &ui.preheat_fan_speed[material], 0, 255); #if HAS_TEMP_HOTEND MENU_ITEM_EDIT(int3, MSG_NOZZLE, &ui.preheat_hotend_temp[material], MINTEMP_ALL, MAXTEMP_ALL - 15); #endif diff --git a/Marlin/src/lcd/menu/menu_custom.cpp b/Marlin/src/lcd/menu/menu_custom.cpp index 33ec5352e0..ad346e71df 100644 --- a/Marlin/src/lcd/menu/menu_custom.cpp +++ b/Marlin/src/lcd/menu/menu_custom.cpp @@ -39,7 +39,7 @@ void _lcd_user_gcode(PGM_P const cmd) { queue.inject_P(cmd); - #if ENABLED(USER_SCRIPT_AUDIBLE_FEEDBACK) + #if ENABLED(USER_SCRIPT_AUDIBLE_FEEDBACK) && HAS_BUZZER ui.completion_feedback(); #endif #if ENABLED(USER_SCRIPT_RETURN) diff --git a/Marlin/src/lcd/menu/menu_delta_calibrate.cpp b/Marlin/src/lcd/menu/menu_delta_calibrate.cpp index 653da795d6..a4770d0f86 100644 --- a/Marlin/src/lcd/menu/menu_delta_calibrate.cpp +++ b/Marlin/src/lcd/menu/menu_delta_calibrate.cpp @@ -39,7 +39,7 @@ void _man_probe_pt(const float &rx, const float &ry) { do_blocking_move_to(rx, ry, Z_CLEARANCE_BETWEEN_PROBES); ui.synchronize(); - move_menu_scale = MAX(PROBE_MANUALLY_STEP, MIN_STEPS_PER_SEGMENT / float(DEFAULT_XYZ_STEPS_PER_UNIT)); + move_menu_scale = _MAX(PROBE_MANUALLY_STEP, MIN_STEPS_PER_SEGMENT / float(DEFAULT_XYZ_STEPS_PER_UNIT)); ui.goto_screen(lcd_move_z); } diff --git a/Marlin/src/lcd/menu/menu_info.cpp b/Marlin/src/lcd/menu/menu_info.cpp index f7b6f3a491..08edaea438 100644 --- a/Marlin/src/lcd/menu/menu_info.cpp +++ b/Marlin/src/lcd/menu/menu_info.cpp @@ -28,20 +28,12 @@ #if HAS_LCD_MENU && ENABLED(LCD_INFO_MENU) +#include "menu.h" + #if HAS_GAMES #include "game/game.h" #endif -#include "menu.h" -// #include "../../module/motion.h" -// #include "../../module/planner.h" -// #include "../../module/temperature.h" -// #include "../../Marlin.h" - -// #if HAS_LEVELING -// #include "../../feature/bedlevel/bedlevel.h" -// #endif - #if ENABLED(PRINTCOUNTER) #include "../../module/printcounter.h" @@ -183,28 +175,42 @@ void menu_info_board() { // // About Printer > Printer Info // -void menu_info_printer() { - if (ui.use_click()) return ui.goto_previous_screen(); - START_SCREEN(); - STATIC_ITEM(MSG_MARLIN, true, true); // Marlin - STATIC_ITEM(SHORT_BUILD_VERSION, true); // x.x.x-Branch - STATIC_ITEM(STRING_DISTRIBUTION_DATE, true); // YYYY-MM-DD HH:MM - STATIC_ITEM(MACHINE_NAME, true); // My3DPrinter - STATIC_ITEM(WEBSITE_URL, true); // www.my3dprinter.com - STATIC_ITEM(MSG_INFO_EXTRUDERS ": " STRINGIFY(EXTRUDERS), true); // Extruders: 2 - #if ENABLED(AUTO_BED_LEVELING_3POINT) - STATIC_ITEM(MSG_3POINT_LEVELING, true); // 3-Point Leveling - #elif ENABLED(AUTO_BED_LEVELING_LINEAR) - STATIC_ITEM(MSG_LINEAR_LEVELING, true); // Linear Leveling - #elif ENABLED(AUTO_BED_LEVELING_BILINEAR) - STATIC_ITEM(MSG_BILINEAR_LEVELING, true); // Bi-linear Leveling - #elif ENABLED(AUTO_BED_LEVELING_UBL) - STATIC_ITEM(MSG_UBL_LEVELING, true); // Unified Bed Leveling - #elif ENABLED(MESH_BED_LEVELING) - STATIC_ITEM(MSG_MESH_LEVELING, true); // Mesh Leveling +#if DISABLED(LCD_PRINTER_INFO_IS_BOOTSCREEN) + void menu_info_printer() { + if (ui.use_click()) return ui.goto_previous_screen(); + START_SCREEN(); + STATIC_ITEM(MSG_MARLIN, true, true); // Marlin + STATIC_ITEM(SHORT_BUILD_VERSION, true); // x.x.x-Branch + STATIC_ITEM(STRING_DISTRIBUTION_DATE, true); // YYYY-MM-DD HH:MM + STATIC_ITEM(MACHINE_NAME, true); // My3DPrinter + STATIC_ITEM(WEBSITE_URL, true); // www.my3dprinter.com + STATIC_ITEM(MSG_INFO_EXTRUDERS ": " STRINGIFY(EXTRUDERS), true); // Extruders: 2 + #if ENABLED(AUTO_BED_LEVELING_3POINT) + STATIC_ITEM(MSG_3POINT_LEVELING, true); // 3-Point Leveling + #elif ENABLED(AUTO_BED_LEVELING_LINEAR) + STATIC_ITEM(MSG_LINEAR_LEVELING, true); // Linear Leveling + #elif ENABLED(AUTO_BED_LEVELING_BILINEAR) + STATIC_ITEM(MSG_BILINEAR_LEVELING, true); // Bi-linear Leveling + #elif ENABLED(AUTO_BED_LEVELING_UBL) + STATIC_ITEM(MSG_UBL_LEVELING, true); // Unified Bed Leveling + #elif ENABLED(MESH_BED_LEVELING) + STATIC_ITEM(MSG_MESH_LEVELING, true); // Mesh Leveling + #endif + END_SCREEN(); + } +#else + void menu_show_marlin_bootscreen() { + if (ui.use_click()) { ui.goto_previous_screen_no_defer(); } + ui.draw_marlin_bootscreen(); + } + + #if ENABLED(SHOW_CUSTOM_BOOTSCREEN) + void menu_show_custom_bootscreen() { + if (ui.use_click()) { ui.goto_screen(menu_show_marlin_bootscreen); } + ui.draw_custom_bootscreen(); + } #endif - END_SCREEN(); -} +#endif // LCD_PRINTER_INFO_IS_BOOTSCREEN // // "About Printer" submenu @@ -212,14 +218,30 @@ void menu_info_printer() { void menu_info() { START_MENU(); MENU_BACK(MSG_MAIN); - MENU_ITEM(submenu, MSG_INFO_PRINTER_MENU, menu_info_printer); // Printer Info > - MENU_ITEM(submenu, MSG_INFO_BOARD_MENU, menu_info_board); // Board Info > - MENU_ITEM(submenu, MSG_INFO_THERMISTOR_MENU, menu_info_thermistors); // Thermistors > + #if ENABLED(LCD_PRINTER_INFO_IS_BOOTSCREEN) + MENU_ITEM(submenu, MSG_INFO_PRINTER_MENU, ( + #if ENABLED(SHOW_CUSTOM_BOOTSCREEN) + menu_show_custom_bootscreen + #else + menu_show_marlin_bootscreen + #endif + )); + #else + MENU_ITEM(submenu, MSG_INFO_PRINTER_MENU, menu_info_printer); // Printer Info > + MENU_ITEM(submenu, MSG_INFO_BOARD_MENU, menu_info_board); // Board Info > + MENU_ITEM(submenu, MSG_INFO_THERMISTOR_MENU, menu_info_thermistors); // Thermistors > + #endif + #if ENABLED(PRINTCOUNTER) MENU_ITEM(submenu, MSG_INFO_STATS_MENU, menu_info_stats); // Printer Stats > #endif + #if HAS_GAMES - MENU_ITEM(submenu, "Game", ( + #if ENABLED(GAMES_EASTER_EGG) + MENU_ITEM_DUMMY(); + MENU_ITEM_DUMMY(); + #endif + MENU_ITEM(submenu, MSG_GAMES, ( #if HAS_GAME_MENU menu_game #elif ENABLED(MARLIN_BRICKOUT) @@ -233,6 +255,7 @@ void menu_info() { #endif )); #endif + END_MENU(); } diff --git a/Marlin/src/lcd/menu/menu_main.cpp b/Marlin/src/lcd/menu/menu_main.cpp index d334a56fe8..081b208fdb 100644 --- a/Marlin/src/lcd/menu/menu_main.cpp +++ b/Marlin/src/lcd/menu/menu_main.cpp @@ -250,7 +250,11 @@ void menu_main() { #endif #if HAS_GAMES && DISABLED(LCD_INFO_MENU) - MENU_ITEM(submenu, "Game", ( + #if ENABLED(GAMES_EASTER_EGG) + MENU_ITEM_DUMMY(); + MENU_ITEM_DUMMY(); + #endif + MENU_ITEM(submenu, MSG_GAMES, ( #if HAS_GAME_MENU menu_game #elif ENABLED(MARLIN_BRICKOUT) diff --git a/Marlin/src/lcd/menu/menu_mixer.cpp b/Marlin/src/lcd/menu/menu_mixer.cpp index 1a17dbd260..cd23282044 100644 --- a/Marlin/src/lcd/menu/menu_mixer.cpp +++ b/Marlin/src/lcd/menu/menu_mixer.cpp @@ -41,7 +41,6 @@ void lcd_mixer_gradient_z_start_edit() { ui.defer_status_screen(); - ui.encoder_direction_normal(); ENCODER_RATE_MULTIPLY(true); if (ui.encoderPosition != 0) { mixer.gradient.start_z += float(int16_t(ui.encoderPosition)) * 0.1; @@ -66,7 +65,6 @@ void lcd_mixer_gradient_z_end_edit() { ui.defer_status_screen(); - ui.encoder_direction_normal(); ENCODER_RATE_MULTIPLY(true); if (ui.encoderPosition != 0) { mixer.gradient.end_z += float(int16_t(ui.encoderPosition)) * 0.1; @@ -274,17 +272,10 @@ void menu_mixer() { #endif ); - MENU_ITEM(submenu, MSG_MIX, - #if CHANNEL_MIX_EDITING - _lcd_goto_mix_edit - #elif DUAL_MIXING_EXTRUDER - lcd_mixer_mix_edit - #endif - ); - #if DUAL_MIXING_EXTRUDER { char tmp[10]; + MENU_ITEM(submenu, MSG_MIX, lcd_mixer_mix_edit); MENU_ITEM_ADDON_START(10); mixer.update_mix_from_vtool(); sprintf_P(tmp, PSTR("%3d;%3d%%"), int(mixer.mix[0]), int(mixer.mix[1])); @@ -292,6 +283,8 @@ void menu_mixer() { MENU_ITEM_ADDON_END(); MENU_ITEM(function, MSG_TOGGLE_MIX, _lcd_mixer_toggle_mix); } + #else + MENU_ITEM(submenu, MSG_MIX, _lcd_goto_mix_edit); #endif MENU_ITEM(submenu, MSG_RESET_VTOOLS, menu_mixer_vtools_reset_confirm); diff --git a/Marlin/src/lcd/menu/menu_motion.cpp b/Marlin/src/lcd/menu/menu_motion.cpp index a87329e325..223d1077aa 100644 --- a/Marlin/src/lcd/menu/menu_motion.cpp +++ b/Marlin/src/lcd/menu/menu_motion.cpp @@ -29,6 +29,13 @@ #if HAS_LCD_MENU #include "menu.h" + +#include "../lcdprint.h" + +#if HAS_GRAPHICAL_LCD + #include "../dogm/ultralcd_DOGM.h" +#endif + #include "../../module/motion.h" #if ENABLED(DELTA) @@ -74,7 +81,6 @@ inline void manual_move_to_current(AxisEnum axis static void _lcd_move_xyz(PGM_P name, AxisEnum axis) { if (ui.use_click()) return ui.goto_previous_screen_no_defer(); - ui.encoder_direction_normal(); if (ui.encoderPosition && !ui.processing_manual_move) { // Start with no limits to movement @@ -158,7 +164,6 @@ static void _lcd_move_e( #endif ) { if (ui.use_click()) return ui.goto_previous_screen_no_defer(); - ui.encoder_direction_normal(); if (ui.encoderPosition) { if (!ui.processing_manual_move) { const float diff = float(int16_t(ui.encoderPosition)) * move_menu_scale; @@ -232,6 +237,10 @@ inline void lcd_move_e() { _lcd_move_e(); } // "Motion" > "Move Xmm" > "Move XYZ" submenu // +#ifndef SHORT_MANUAL_Z_MOVE + #define SHORT_MANUAL_Z_MOVE 0.025 +#endif + screenFunc_t _manual_move_func_ptr; void _goto_manual_move(const float scale) { @@ -242,7 +251,6 @@ void _goto_manual_move(const float scale) { void menu_move_10mm() { _goto_manual_move(10); } void menu_move_1mm() { _goto_manual_move( 1); } void menu_move_01mm() { _goto_manual_move( 0.1f); } -void menu_move_0025mm() { _goto_manual_move( 0.025f); } void _menu_move_distance(const AxisEnum axis, const screenFunc_t func, const int8_t eindex=-1) { _manual_move_func_ptr = func; @@ -270,8 +278,18 @@ void _menu_move_distance(const AxisEnum axis, const screenFunc_t func, const int MENU_ITEM(submenu, MSG_MOVE_10MM, menu_move_10mm); MENU_ITEM(submenu, MSG_MOVE_1MM, menu_move_1mm); MENU_ITEM(submenu, MSG_MOVE_01MM, menu_move_01mm); - if (axis == Z_AXIS) - MENU_ITEM(submenu, MSG_MOVE_0025MM, menu_move_0025mm); + if (axis == Z_AXIS && (SHORT_MANUAL_Z_MOVE) > 0.0f && (SHORT_MANUAL_Z_MOVE) < 0.1f) { + MENU_ITEM(submenu, "", []{ _goto_manual_move(float(SHORT_MANUAL_Z_MOVE)); }); + MENU_ITEM_ADDON_START(1); + char tmp[20], numstr[10]; + // Determine digits needed right of decimal + const uint8_t digs = !UNEAR_ZERO((SHORT_MANUAL_Z_MOVE) * 1000 - int((SHORT_MANUAL_Z_MOVE) * 1000)) ? 4 : + !UNEAR_ZERO((SHORT_MANUAL_Z_MOVE) * 100 - int((SHORT_MANUAL_Z_MOVE) * 100)) ? 3 : 2; + dtostrf(SHORT_MANUAL_Z_MOVE, 1, digs, numstr); + sprintf_P(tmp, PSTR(MSG_MOVE_Z_DIST), numstr); + LCDPRINT(tmp); + MENU_ITEM_ADDON_END(); + } } END_MENU(); } @@ -416,8 +434,11 @@ void menu_move() { END_MENU(); } -void _lcd_ubl_level_bed(); -void menu_bed_leveling(); +#if ENABLED(AUTO_BED_LEVELING_UBL) + void _lcd_ubl_level_bed(); +#elif ENABLED(LCD_BED_LEVELING) + void menu_bed_leveling(); +#endif void menu_motion() { START_MENU(); @@ -482,6 +503,10 @@ void menu_motion() { MENU_ITEM(function, MSG_LEVEL_CORNERS, _lcd_level_bed_corners); #endif + #if ENABLED(Z_MIN_PROBE_REPEATABILITY_TEST) + MENU_ITEM(gcode, MSG_M48_TEST, PSTR("G28\nM48 P10")); + #endif + // // Disable Steppers // diff --git a/Marlin/src/lcd/menu/menu_service.cpp b/Marlin/src/lcd/menu/menu_service.cpp index 5f30856f0b..6eee178143 100644 --- a/Marlin/src/lcd/menu/menu_service.cpp +++ b/Marlin/src/lcd/menu/menu_service.cpp @@ -38,7 +38,9 @@ inline void _menu_service(const int index, PGM_P const name) { PSTR(MSG_BUTTON_RESET), PSTR(MSG_BUTTON_CANCEL), []{ print_job_timer.resetServiceInterval(index); - ui.completion_feedback(true); + #if HAS_BUZZER + ui.completion_feedback(); + #endif ui.reset_status(); ui.return_to_status(); }, diff --git a/Marlin/src/lcd/menu/menu_temperature.cpp b/Marlin/src/lcd/menu/menu_temperature.cpp index 7c7a17e9dd..ad987850fd 100644 --- a/Marlin/src/lcd/menu/menu_temperature.cpp +++ b/Marlin/src/lcd/menu/menu_temperature.cpp @@ -48,7 +48,7 @@ uint8_t MarlinUI::preheat_fan_speed[2]; // void _lcd_preheat(const int16_t endnum, const int16_t temph, const int16_t tempb, const uint8_t fan) { - if (temph > 0) thermalManager.setTargetHotend(MIN(heater_maxtemp[endnum] - 15, temph), endnum); + if (temph > 0) thermalManager.setTargetHotend(_MIN(heater_maxtemp[endnum] - 15, temph), endnum); #if HAS_HEATED_BED if (tempb >= 0) thermalManager.setTargetBed(tempb); #else diff --git a/Marlin/src/lcd/menu/menu_tune.cpp b/Marlin/src/lcd/menu/menu_tune.cpp index adbcbefc56..1c038ea133 100644 --- a/Marlin/src/lcd/menu/menu_tune.cpp +++ b/Marlin/src/lcd/menu/menu_tune.cpp @@ -73,7 +73,6 @@ void _lcd_babystep(const AxisEnum axis, PGM_P const msg) { if (ui.use_click()) return ui.goto_previous_screen_no_defer(); - ui.encoder_direction_normal(); if (ui.encoderPosition) { const int16_t steps = int16_t(ui.encoderPosition) * (BABYSTEP_MULTIPLICATOR); ui.encoderPosition = 0; diff --git a/Marlin/src/lcd/menu/menu_ubl.cpp b/Marlin/src/lcd/menu/menu_ubl.cpp index 2323804658..3a84d22fdc 100644 --- a/Marlin/src/lcd/menu/menu_ubl.cpp +++ b/Marlin/src/lcd/menu/menu_ubl.cpp @@ -468,7 +468,6 @@ void _lcd_ubl_output_map_lcd() { static int16_t step_scaler = 0; if (ui.use_click()) return _lcd_ubl_map_lcd_edit_cmd(); - ui.encoder_direction_normal(); if (ui.encoderPosition) { step_scaler += int16_t(ui.encoderPosition); diff --git a/Marlin/src/lcd/ultralcd.cpp b/Marlin/src/lcd/ultralcd.cpp index fb4975585d..cc196095d1 100644 --- a/Marlin/src/lcd/ultralcd.cpp +++ b/Marlin/src/lcd/ultralcd.cpp @@ -102,6 +102,11 @@ #if HAS_SLOW_BUTTONS volatile uint8_t MarlinUI::slow_buttons; #endif + #if ENABLED(TOUCH_BUTTONS) + #include "../feature/touch/xpt2046.h" + volatile uint8_t MarlinUI::touch_buttons; + uint8_t MarlinUI::read_touch_buttons() { return touch.read_buttons(); } + #endif #endif #if ENABLED(INIT_SDCARD_ON_BOOT) @@ -150,7 +155,7 @@ millis_t next_button_update_ms; static uint8_t filename_scroll_hash; if (filename_scroll_hash != hash) { // If the hash changed... filename_scroll_hash = hash; // Save the new hash - filename_scroll_max = MAX(0, utf8_strlen(theCard.longFilename) - maxlen); // Update the scroll limit + filename_scroll_max = _MAX(0, utf8_strlen(theCard.longFilename) - maxlen); // Update the scroll limit filename_scroll_pos = 0; // Reset scroll to the start lcd_status_update_delay = 8; // Don't scroll right away } @@ -176,8 +181,8 @@ millis_t next_button_update_ms; } #endif - #if ENABLED(REVERSE_MENU_DIRECTION) - int8_t MarlinUI::encoderDirection = 1; + #if EITHER(REVERSE_MENU_DIRECTION, REVERSE_SELECT_DIRECTION) + int8_t MarlinUI::encoderDirection = ENCODERBASE; #endif bool MarlinUI::lcd_clicked; @@ -324,8 +329,13 @@ void MarlinUI::init() { #endif #endif - #if HAS_ENCODER_ACTION && HAS_SLOW_BUTTONS - slow_buttons = 0; + #if HAS_ENCODER_ACTION + #if HAS_SLOW_BUTTONS + slow_buttons = 0; + #endif + #if ENABLED(TOUCH_BUTTONS) + touch_buttons = 0; + #endif #endif update_buttons(); @@ -382,7 +392,7 @@ bool MarlinUI::get_blink() { #if HAS_ENCODER_ACTION refresh(LCDVIEW_REDRAW_NOW); #if HAS_LCD_MENU - if (encoderDirection == -1) { // ADC_KEYPAD forces REVERSE_MENU_DIRECTION, so this indicates menu navigation + if (encoderDirection == -(ENCODERBASE)) { // ADC_KEYPAD forces REVERSE_MENU_DIRECTION, so this indicates menu navigation if (RRK(EN_KEYPAD_UP)) encoderPosition += ENCODER_STEPS_PER_MENU_ITEM; else if (RRK(EN_KEYPAD_DOWN)) encoderPosition -= ENCODER_STEPS_PER_MENU_ITEM; else if (RRK(EN_KEYPAD_LEFT)) { MenuItem_back::action(); quick_feedback(); } @@ -470,7 +480,6 @@ bool MarlinUI::get_blink() { void MarlinUI::status_screen() { #if HAS_LCD_MENU - encoder_direction_normal(); ENCODER_RATE_MULTIPLY(false); #endif @@ -529,7 +538,7 @@ void MarlinUI::status_screen() { return; } - #endif // HAS_LCD_MENU + #endif #if ENABLED(ULTIPANEL_FEEDMULTIPLY) @@ -548,12 +557,12 @@ void MarlinUI::status_screen() { else if ((old_frm < 100 && new_frm > 100) || (old_frm > 100 && new_frm < 100)) new_frm = 100; - new_frm = constrain(new_frm, 10, 999); + LIMIT(new_frm, 10, 999); if (old_frm != new_frm) { feedrate_percentage = new_frm; encoderPosition = 0; - #if ENABLED(BEEP_ON_FEEDRATE_CHANGE) + #if HAS_BUZZER && ENABLED(BEEP_ON_FEEDRATE_CHANGE) static millis_t next_beep; #ifndef GOT_MS const millis_t ms = millis(); @@ -578,8 +587,8 @@ void MarlinUI::kill_screen(PGM_P lcd_msg) { #ifdef LED_BACKLIGHT_TIMEOUT leds.set_color(LEDColorRed()); #ifdef NEOPIXEL_BKGD_LED_INDEX - pixels.setPixelColor(NEOPIXEL_BKGD_LED_INDEX, 255, 0, 0, 0); - pixels.show(); + neo.set_pixel_color(NEOPIXEL_BKGD_LED_INDEX, 255, 0, 0, 0); + neo.show(); #endif #endif @@ -599,8 +608,10 @@ void MarlinUI::quick_feedback(const bool clear_buttons/*=true*/) { UNUSED(clear_buttons); #endif - // Buzz and wait. The delay is needed for buttons to settle! - buzz(LCD_FEEDBACK_FREQUENCY_DURATION_MS, LCD_FEEDBACK_FREQUENCY_HZ); + #if HAS_BUZZER + // Buzz and wait. Is the delay needed for buttons to settle? + buzz(LCD_FEEDBACK_FREQUENCY_DURATION_MS, LCD_FEEDBACK_FREQUENCY_HZ); + #endif #if HAS_LCD_MENU #if ENABLED(LCD_USE_I2C_BUZZER) @@ -793,7 +804,9 @@ void MarlinUI::update() { card.release(); if (old_sd_status != 2) { set_status_P(PSTR(MSG_SD_REMOVED)); - if (!on_status_screen()) return_to_status(); + #if HAS_LCD_MENU + return_to_status(); + #endif } } @@ -823,6 +836,11 @@ void MarlinUI::update() { next_lcd_update_ms = ms + LCD_UPDATE_INTERVAL; + #if ENABLED(TOUCH_BUTTONS) + if (on_status_screen()) + next_lcd_update_ms += (LCD_UPDATE_INTERVAL) * 2; + #endif + #if ENABLED(LCD_HAS_STATUS_INDICATORS) update_indicators(); #endif @@ -833,6 +851,10 @@ void MarlinUI::update() { slow_buttons = read_slow_buttons(); // Buttons that take too long to read in interrupt context #endif + #if ENABLED(TOUCH_BUTTONS) + touch_buttons = read_touch_buttons(); + #endif + #if ENABLED(REPRAPWORLD_KEYPAD) if (handle_keypad()) { @@ -1180,6 +1202,9 @@ void MarlinUI::update() { #if HAS_SLOW_BUTTONS | slow_buttons #endif + #if ENABLED(TOUCH_BUTTONS) + | touch_buttons + #endif ; #elif HAS_ADC_BUTTONS buttons = 0; @@ -1446,7 +1471,7 @@ void MarlinUI::update() { #endif print_job_timer.stop(); set_status_P(PSTR(MSG_PRINT_ABORTED)); - #if HAS_SPI_LCD + #if HAS_LCD_MENU return_to_status(); #endif } @@ -1500,13 +1525,15 @@ void MarlinUI::update() { uint8_t MarlinUI::get_progress() { #if ENABLED(LCD_SET_PROGRESS_MANUALLY) uint8_t &progress = progress_bar_percent; + #define _PLIMIT(P) ((P) & 0x7F) #else + #define _PLIMIT(P) P uint8_t progress = 0; #endif #if ENABLED(SDSUPPORT) if (IS_SD_PRINTING()) progress = card.percentDone(); #endif - return progress; + return _PLIMIT(progress); } #endif diff --git a/Marlin/src/lcd/ultralcd.h b/Marlin/src/lcd/ultralcd.h index 270005ee35..0d66e2073e 100644 --- a/Marlin/src/lcd/ultralcd.h +++ b/Marlin/src/lcd/ultralcd.h @@ -56,7 +56,11 @@ uint8_t get_ADC_keyValue(); #endif - #define LCD_UPDATE_INTERVAL 100 + #if ENABLED(TOUCH_BUTTONS) + #define LCD_UPDATE_INTERVAL 50 + #else + #define LCD_UPDATE_INTERVAL 100 + #endif #if HAS_LCD_MENU @@ -254,15 +258,17 @@ public: #endif } - static inline void buzz(const long duration, const uint16_t freq) { - #if ENABLED(LCD_USE_I2C_BUZZER) - lcd.buzz(duration, freq); - #elif PIN_EXISTS(BEEPER) - buzzer.tone(duration, freq); - #else - UNUSED(duration); UNUSED(freq); - #endif - } + #if HAS_BUZZER + static inline void buzz(const long duration, const uint16_t freq) { + #if ENABLED(LCD_USE_I2C_BUZZER) + lcd.buzz(duration, freq); + #elif PIN_EXISTS(BEEPER) + buzzer.tone(duration, freq); + #elif ENABLED(PCA9632_BUZZER) + pca9632_buzz(duration, freq); + #endif + } + #endif // LCD implementations static void clear_lcd(); @@ -293,7 +299,9 @@ public: #if HAS_PRINT_PROGRESS #if ENABLED(LCD_SET_PROGRESS_MANUALLY) static uint8_t progress_bar_percent; - static void set_progress(const uint8_t progress) { progress_bar_percent = MIN(progress, 100); } + static void set_progress(const uint8_t progress) { progress_bar_percent = _MIN(progress, 100); } + static void set_progress_done() { set_progress(0x80 + 100); } + static void progress_reset() { if (progress_bar_percent & 0x80) set_progress(0); } #endif static uint8_t get_progress(); #else @@ -309,7 +317,14 @@ public: static inline void refresh(const LCDViewAction type) { lcdDrawUpdate = type; } static inline void refresh() { refresh(LCDVIEW_CLEAR_CALL_REDRAW); } + #if ENABLED(SHOW_CUSTOM_BOOTSCREEN) + static void draw_custom_bootscreen(const uint8_t frame=0); + static void show_custom_bootscreen(); + #endif + #if ENABLED(SHOW_BOOTSCREEN) + static void draw_marlin_bootscreen(); + static void show_marlin_bootscreen(); static void show_bootscreen(); #endif @@ -349,7 +364,9 @@ public: #endif static void quick_feedback(const bool clear_buttons=true); - static void completion_feedback(const bool good=true); + #if HAS_BUZZER + static void completion_feedback(const bool good=true); + #endif #if DISABLED(LIGHTWEIGHT_UI) static void draw_status_message(const bool blink); @@ -418,6 +435,11 @@ public: static int16_t preheat_hotend_temp[2], preheat_bed_temp[2]; static uint8_t preheat_fan_speed[2]; + // Select Screen (modal NO/YES style dialog) + static bool selection; + static void set_selection(const bool sel) { selection = sel; } + static bool update_selection(); + static void manage_manual_move(); static bool lcd_clicked; @@ -455,7 +477,11 @@ public: #endif #if ENABLED(G26_MESH_VALIDATION) - static inline void chirp() { buzz(LCD_FEEDBACK_FREQUENCY_DURATION_MS, LCD_FEEDBACK_FREQUENCY_HZ); } + static inline void chirp() { + #if HAS_BUZZER + buzz(LCD_FEEDBACK_FREQUENCY_DURATION_MS, LCD_FEEDBACK_FREQUENCY_HZ); + #endif + } #endif #if ENABLED(AUTO_BED_LEVELING_UBL) @@ -497,6 +523,11 @@ public: static volatile uint8_t slow_buttons; static uint8_t read_slow_buttons(); #endif + #if ENABLED(TOUCH_BUTTONS) + static volatile uint8_t touch_buttons; + static uint8_t read_touch_buttons(); + #endif + static void update_buttons(); static inline bool button_pressed() { return BUTTON_CLICK(); } #if EITHER(AUTO_BED_LEVELING_UBL, G26_MESH_VALIDATION) @@ -510,15 +541,25 @@ public: #else #define ENCODERBASE +1 #endif - #if ENABLED(REVERSE_MENU_DIRECTION) + + #if EITHER(REVERSE_MENU_DIRECTION, REVERSE_SELECT_DIRECTION) static int8_t encoderDirection; - static inline void encoder_direction_normal() { encoderDirection = +(ENCODERBASE); } - static inline void encoder_direction_menus() { encoderDirection = -(ENCODERBASE); } + static inline void encoder_direction_normal() { encoderDirection = ENCODERBASE; } #else static constexpr int8_t encoderDirection = ENCODERBASE; static inline void encoder_direction_normal() {} + #endif + + #if ENABLED(REVERSE_MENU_DIRECTION) + static inline void encoder_direction_menus() { encoderDirection = -(ENCODERBASE); } + #else static inline void encoder_direction_menus() {} #endif + #if ENABLED(REVERSE_SELECT_DIRECTION) + static inline void encoder_direction_select() { encoderDirection = -(ENCODERBASE); } + #else + static inline void encoder_direction_select() {} + #endif #else diff --git a/Marlin/src/libs/least_squares_fit.h b/Marlin/src/libs/least_squares_fit.h index 46feb62b33..8eb47585e0 100644 --- a/Marlin/src/libs/least_squares_fit.h +++ b/Marlin/src/libs/least_squares_fit.h @@ -61,8 +61,8 @@ void inline incremental_WLSF(struct linear_fit_data *lsf, const float &x, const lsf->xzbar += w * x * z; lsf->yzbar += w * y * z; lsf->N += w; - lsf->max_absx = MAX(ABS(w * x), lsf->max_absx); - lsf->max_absy = MAX(ABS(w * y), lsf->max_absy); + lsf->max_absx = _MAX(ABS(w * x), lsf->max_absx); + lsf->max_absy = _MAX(ABS(w * y), lsf->max_absy); } void inline incremental_LSF(struct linear_fit_data *lsf, const float &x, const float &y, const float &z) { @@ -75,8 +75,8 @@ void inline incremental_LSF(struct linear_fit_data *lsf, const float &x, const f lsf->xybar += x * y; lsf->xzbar += x * z; lsf->yzbar += y * z; - lsf->max_absx = MAX(ABS(x), lsf->max_absx); - lsf->max_absy = MAX(ABS(y), lsf->max_absy); + lsf->max_absx = _MAX(ABS(x), lsf->max_absx); + lsf->max_absy = _MAX(ABS(y), lsf->max_absy); lsf->N += 1.0; } diff --git a/Marlin/src/libs/nozzle.cpp b/Marlin/src/libs/nozzle.cpp index 9ea6c90c46..3926bfc93c 100644 --- a/Marlin/src/libs/nozzle.cpp +++ b/Marlin/src/libs/nozzle.cpp @@ -26,6 +26,8 @@ #include "nozzle.h" +Nozzle nozzle; + #include "../Marlin.h" #include "../module/motion.h" #include "point_t.h" @@ -46,7 +48,11 @@ #endif // Move to the starting point - do_blocking_move_to(start.x, start.y, start.z); + #if ENABLED(NOZZLE_CLEAN_NO_Z) + do_blocking_move_to_xy(start.x, start.y); + #else + do_blocking_move_to(start.x, start.y, start.z); + #endif // Start the stroke pattern for (uint8_t i = 0; i < (strokes >> 1); i++) { @@ -76,7 +82,11 @@ const float ix = current_position[X_AXIS], iy = current_position[Y_AXIS], iz = current_position[Z_AXIS]; #endif - do_blocking_move_to(start.x, start.y, start.z); + #if ENABLED(NOZZLE_CLEAN_NO_Z) + do_blocking_move_to_xy(start.x, start.y); + #else + do_blocking_move_to(start.x, start.y, start.z); + #endif const uint8_t zigs = objects << 1; const bool horiz = ABS(diffx) >= ABS(diffy); // Do a horizontal wipe? @@ -119,7 +129,11 @@ const float ix = current_position[X_AXIS], iy = current_position[Y_AXIS], iz = current_position[Z_AXIS]; #endif - do_blocking_move_to(start.x, start.y, start.z); + #if ENABLED(NOZZLE_CLEAN_NO_Z) + do_blocking_move_to_xy(start.x, start.y); + #else + do_blocking_move_to(start.x, start.y, start.z); + #endif for (uint8_t s = 0; s < strokes; s++) for (uint8_t i = 0; i < NOZZLE_CLEAN_CIRCLE_FN; i++) @@ -143,18 +157,34 @@ * @param pattern one of the available patterns * @param argument depends on the cleaning pattern */ - void Nozzle::clean(const uint8_t &pattern, const uint8_t &strokes, const float &radius, const uint8_t &objects/*=0*/) { + void Nozzle::clean(const uint8_t &pattern, const uint8_t &strokes, const float &radius, const uint8_t &objects, const uint8_t cleans) { + point_t start = NOZZLE_CLEAN_START_POINT; + point_t end = NOZZLE_CLEAN_END_POINT; + + if (pattern == 2) { + if (!(cleans & (_BV(X_AXIS) | _BV(Y_AXIS)))) { + SERIAL_ECHOLNPGM("Warning : Clean Circle requires XY"); + return; + } + end = NOZZLE_CLEAN_CIRCLE_MIDDLE; + } + else { + if (!TEST(cleans, X_AXIS)) start.x = end.x = current_position[X_AXIS]; + if (!TEST(cleans, Y_AXIS)) start.y = end.y = current_position[Y_AXIS]; + } + if (!TEST(cleans, Z_AXIS)) start.z = end.z = current_position[Z_AXIS]; + switch (pattern) { case 1: - zigzag(NOZZLE_CLEAN_START_POINT, NOZZLE_CLEAN_END_POINT, strokes, objects); + zigzag(start, end, strokes, objects); break; case 2: - circle(NOZZLE_CLEAN_START_POINT, NOZZLE_CLEAN_CIRCLE_MIDDLE, strokes, radius); + circle(start, end, strokes, radius); break; default: - stroke(NOZZLE_CLEAN_START_POINT, NOZZLE_CLEAN_END_POINT, strokes); + stroke(start, end, strokes); } } @@ -162,9 +192,9 @@ #if ENABLED(NOZZLE_PARK_FEATURE) - void Nozzle::park(const uint8_t z_action, const point_t &park /*= NOZZLE_PARK_POINT*/) { - const float fr_xy = NOZZLE_PARK_XY_FEEDRATE; - const float fr_z = NOZZLE_PARK_Z_FEEDRATE; + void Nozzle::park(const uint8_t z_action, const point_t &park/*=NOZZLE_PARK_POINT*/) { + const float fr_xy = NOZZLE_PARK_XY_FEEDRATE, + fr_z = NOZZLE_PARK_Z_FEEDRATE; switch (z_action) { case 1: // Go to Z-park height @@ -172,11 +202,11 @@ break; case 2: // Raise by Z-park height - do_blocking_move_to_z(MIN(current_position[Z_AXIS] + park.z, Z_MAX_POS), fr_z); + do_blocking_move_to_z(_MIN(current_position[Z_AXIS] + park.z, Z_MAX_POS), fr_z); break; default: // Raise to at least the Z-park height - do_blocking_move_to_z(MAX(park.z, current_position[Z_AXIS]), fr_z); + do_blocking_move_to_z(_MAX(park.z, current_position[Z_AXIS]), fr_z); } do_blocking_move_to_xy(park.x, park.y, fr_xy); diff --git a/Marlin/src/libs/nozzle.h b/Marlin/src/libs/nozzle.h index ad0d8d752d..d20b41de93 100644 --- a/Marlin/src/libs/nozzle.h +++ b/Marlin/src/libs/nozzle.h @@ -78,7 +78,7 @@ class Nozzle { * @param pattern one of the available patterns * @param argument depends on the cleaning pattern */ - static void clean(const uint8_t &pattern, const uint8_t &strokes, const float &radius, const uint8_t &objects=0) _Os; + static void clean(const uint8_t &pattern, const uint8_t &strokes, const float &radius, const uint8_t &objects, const uint8_t cleans) _Os; #endif // NOZZLE_CLEAN_FEATURE @@ -88,3 +88,5 @@ class Nozzle { #endif }; + +extern Nozzle nozzle; diff --git a/Marlin/src/libs/vector_3.h b/Marlin/src/libs/vector_3.h index 0a986374d8..b56e1d60bb 100644 --- a/Marlin/src/libs/vector_3.h +++ b/Marlin/src/libs/vector_3.h @@ -40,8 +40,6 @@ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA */ -#pragma once - class matrix_3x3; struct vector_3 { diff --git a/Marlin/src/module/configuration_store.cpp b/Marlin/src/module/configuration_store.cpp index d396ea3986..70ae30bec4 100644 --- a/Marlin/src/module/configuration_store.cpp +++ b/Marlin/src/module/configuration_store.cpp @@ -37,7 +37,7 @@ */ // Change EEPROM version if the structure changes -#define EEPROM_VERSION "V67" +#define EEPROM_VERSION "V68" #define EEPROM_OFFSET 100 // Check the integrity of data offsets. @@ -98,10 +98,8 @@ #include "../feature/runout.h" #endif -#include "../lcd/extensible_ui/ui_api.h" - #if ENABLED(EXTRA_LIN_ADVANCE_K) -extern float saved_extruder_advance_K[EXTRUDERS]; + extern float saved_extruder_advance_K[EXTRUDERS]; #endif #if EXTRUDERS > 1 @@ -126,7 +124,7 @@ typedef struct { int16_t X, Y, Z; } tmc typedef struct { bool X, Y, Z, X2, Y2, Z2, Z3, E0, E1, E2, E3, E4, E5; } tmc_stealth_enabled_t; // Limit an index to an array size -#define ALIM(I,ARR) MIN(I, COUNT(ARR) - 1) +#define ALIM(I,ARR) _MIN(I, COUNT(ARR) - 1) /** * Current EEPROM Layout @@ -462,7 +460,8 @@ void MarlinSettings::postprocess() { #define EEPROM_SKIP(VAR) (eeprom_index += sizeof(VAR)) #endif - #define EEPROM_START() int eeprom_index = EEPROM_OFFSET; persistentStore.access_start() + #define EEPROM_START() if (!persistentStore.access_start()) { SERIAL_ECHO_MSG("No EEPROM."); return false; } \ + int eeprom_index = EEPROM_OFFSET #define EEPROM_FINISH() persistentStore.access_finish() #define EEPROM_WRITE(VAR) do{ persistentStore.write_data(eeprom_index, (uint8_t*)&VAR, sizeof(VAR), &working_crc); UPDATE_TEST_INDEX(VAR); }while(0) #define EEPROM_READ(VAR) do{ persistentStore.read_data(eeprom_index, (uint8_t*)&VAR, sizeof(VAR), &working_crc, !validating); UPDATE_TEST_INDEX(VAR); }while(0) @@ -576,7 +575,7 @@ void MarlinSettings::postprocess() { #if HAS_FILAMENT_SENSOR const bool &runout_sensor_enabled = runout.enabled; #else - const bool runout_sensor_enabled = false; + const bool runout_sensor_enabled = true; #endif #if HAS_FILAMENT_SENSOR && defined(FILAMENT_RUNOUT_DISTANCE_MM) const float &runout_distance_mm = runout.runout_distance(); @@ -1390,7 +1389,7 @@ void MarlinSettings::postprocess() { float runout_distance_mm; EEPROM_READ(runout_distance_mm); #if HAS_FILAMENT_SENSOR && defined(FILAMENT_RUNOUT_DISTANCE_MM) - runout.set_runout_distance(runout_distance_mm); + if (!validating) runout.set_runout_distance(runout_distance_mm); #endif } @@ -2030,8 +2029,7 @@ void MarlinSettings::postprocess() { const char extui_data[ExtUI::eeprom_data_size] = { 0 }; _FIELD_TEST(extui_data); EEPROM_READ(extui_data); - if(!validating) - ExtUI::onLoadSettings(extui_data); + if (!validating) ExtUI::onLoadSettings(extui_data); } #endif @@ -2114,7 +2112,7 @@ void MarlinSettings::postprocess() { (void)save(); SERIAL_ECHO_MSG("EEPROM Initialized"); #endif - return true; + return false; } #if ENABLED(AUTO_BED_LEVELING_UBL) @@ -2252,7 +2250,7 @@ void MarlinSettings::reset() { planner.max_jerk[X_AXIS] = DEFAULT_XJERK; planner.max_jerk[Y_AXIS] = DEFAULT_YJERK; planner.max_jerk[Z_AXIS] = DEFAULT_ZJERK; - #if DISABLED(JUNCTION_DEVIATION) || DISABLED(LIN_ADVANCE) + #if !BOTH(JUNCTION_DEVIATION, LIN_ADVANCE) planner.max_jerk[E_AXIS] = DEFAULT_EJERK; #endif #endif @@ -2290,6 +2288,7 @@ void MarlinSettings::reset() { #if EXTRUDERS > 1 #if ENABLED(TOOLCHANGE_FILAMENT_SWAP) toolchange_settings.swap_length = TOOLCHANGE_FIL_SWAP_LENGTH; + toolchange_settings.extra_prime = TOOLCHANGE_FIL_EXTRA_PRIME; toolchange_settings.prime_speed = TOOLCHANGE_FIL_SWAP_PRIME_SPEED; toolchange_settings.retract_speed = TOOLCHANGE_FIL_SWAP_RETRACT_SPEED; #endif @@ -2767,7 +2766,7 @@ void MarlinSettings::reset() { #endif #if HAS_CLASSIC_JERK SERIAL_ECHOPGM(" X Y Z"); - #if DISABLED(JUNCTION_DEVIATION) || DISABLED(LIN_ADVANCE) + #if !BOTH(JUNCTION_DEVIATION, LIN_ADVANCE) SERIAL_ECHOPGM(" E"); #endif #endif @@ -2785,7 +2784,7 @@ void MarlinSettings::reset() { , " X", LINEAR_UNIT(planner.max_jerk[X_AXIS]) , " Y", LINEAR_UNIT(planner.max_jerk[Y_AXIS]) , " Z", LINEAR_UNIT(planner.max_jerk[Z_AXIS]) - #if DISABLED(JUNCTION_DEVIATION) || DISABLED(LIN_ADVANCE) + #if !BOTH(JUNCTION_DEVIATION, LIN_ADVANCE) , " E", LINEAR_UNIT(planner.max_jerk[E_AXIS]) #endif #endif diff --git a/Marlin/src/module/configuration_store.h b/Marlin/src/module/configuration_store.h index fc84c4005b..9e95e47525 100644 --- a/Marlin/src/module/configuration_store.h +++ b/Marlin/src/module/configuration_store.h @@ -29,8 +29,6 @@ class MarlinSettings { public: - MarlinSettings() { } - static uint16_t datasize(); static void reset(); @@ -55,9 +53,15 @@ class MarlinSettings { #endif #if ENABLED(EEPROM_SETTINGS) + static bool load(); // Return 'true' if data was loaded ok static bool validate(); // Return 'true' if EEPROM data is ok + static inline void first_load() { + static bool loaded = false; + if (!loaded && load()) loaded = true; + } + #if ENABLED(AUTO_BED_LEVELING_UBL) // Eventually make these available if any leveling system // That can store is enabled static uint16_t meshes_start_index(); @@ -73,6 +77,8 @@ class MarlinSettings { #else FORCE_INLINE static bool load() { reset(); report(); return true; } + FORCE_INLINE + static void first_load() { (void)load(); } #endif #if DISABLED(DISABLE_M503) diff --git a/Marlin/src/module/delta.cpp b/Marlin/src/module/delta.cpp index 466f552274..51f20b2519 100644 --- a/Marlin/src/module/delta.cpp +++ b/Marlin/src/module/delta.cpp @@ -227,7 +227,7 @@ void home_delta() { // Disable stealthChop if used. Enable diag1 pin on driver. #if ENABLED(SENSORLESS_HOMING) - sensorless_t stealth_states { false, false, false, false, false, false, false }; + sensorless_t stealth_states { false }; stealth_states.x = tmc_enable_stallguard(stepperX); stealth_states.y = tmc_enable_stallguard(stepperY); stealth_states.z = tmc_enable_stallguard(stepperZ); diff --git a/Marlin/src/module/delta.h b/Marlin/src/module/delta.h index aa842fb026..24af5daa3a 100644 --- a/Marlin/src/module/delta.h +++ b/Marlin/src/module/delta.h @@ -25,8 +25,6 @@ * delta.h - Delta-specific functions */ -#pragma once - extern float delta_height, delta_endstop_adj[ABC], delta_radius, diff --git a/Marlin/src/module/endstops.cpp b/Marlin/src/module/endstops.cpp index 7234bf4769..9aaab38dd2 100644 --- a/Marlin/src/module/endstops.cpp +++ b/Marlin/src/module/endstops.cpp @@ -330,7 +330,7 @@ void Endstops::resync() { void Endstops::event_handler() { static uint8_t prev_hit_state; // = 0 if (hit_state && hit_state != prev_hit_state) { - #if ENABLED(ULTRA_LCD) + #if HAS_SPI_LCD char chrX = ' ', chrY = ' ', chrZ = ' ', chrP = ' '; #define _SET_STOP_CHAR(A,C) (chr## A = C) #else @@ -361,7 +361,7 @@ void Endstops::event_handler() { #endif SERIAL_EOL(); - #if ENABLED(ULTRA_LCD) + #if HAS_SPI_LCD ui.status_printf_P(0, PSTR(MSG_LCD_ENDSTOPS " %c %c %c %c"), chrX, chrY, chrZ, chrP); #endif @@ -783,14 +783,13 @@ void Endstops::update() { bool Endstops::monitor_flag = false; /** - * monitors endstops & Z probe for changes + * Monitor Endstops and Z Probe for changes * * If a change is detected then the LED is toggled and - * a message is sent out the serial port + * a message is sent out the serial port. * * Yes, we could miss a rapid back & forth change but * that won't matter because this is all manual. - * */ void Endstops::monitor() { diff --git a/Marlin/src/module/endstops.h b/Marlin/src/module/endstops.h index d20e61f702..604befdbb9 100644 --- a/Marlin/src/module/endstops.h +++ b/Marlin/src/module/endstops.h @@ -29,27 +29,16 @@ #include enum EndstopEnum : char { - X_MIN, - Y_MIN, - Z_MIN, - Z_MIN_PROBE, - X_MAX, - Y_MAX, - Z_MAX, - X2_MIN, - X2_MAX, - Y2_MIN, - Y2_MAX, - Z2_MIN, - Z2_MAX, - Z3_MIN, - Z3_MAX + X_MIN, Y_MIN, Z_MIN, Z_MIN_PROBE, + X_MAX, Y_MAX, Z_MAX, + X2_MIN, X2_MAX, + Y2_MIN, Y2_MAX, + Z2_MIN, Z2_MAX, + Z3_MIN, Z3_MAX }; class Endstops { - public: - #if HAS_EXTRA_ENDSTOPS typedef uint16_t esbits_t; #if ENABLED(X_DUAL_ENDSTOPS) diff --git a/Marlin/src/module/motion.cpp b/Marlin/src/module/motion.cpp index e2b61194f8..0216a658c5 100644 --- a/Marlin/src/module/motion.cpp +++ b/Marlin/src/module/motion.cpp @@ -51,7 +51,7 @@ #include "../feature/bltouch.h" #endif -#if EITHER(ULTRA_LCD, EXTENSIBLE_UI) +#if HAS_DISPLAY #include "../lcd/ultralcd.h" #endif @@ -125,7 +125,7 @@ float destination[XYZE]; // = { 0 } ); LOOP_XYZ(i) HOTEND_LOOP() hotend_offset[i][e] = tmp[i][e]; #if ENABLED(DUAL_X_CARRIAGE) - hotend_offset[X_AXIS][1] = MAX(X2_HOME_POS, X2_MAX_POS); + hotend_offset[X_AXIS][1] = _MAX(X2_HOME_POS, X2_MAX_POS); #endif } #endif @@ -423,6 +423,9 @@ void do_blocking_move_to(const float rx, const float ry, const float rz, const f void do_blocking_move_to_x(const float &rx, const float &fr_mm_s/*=0.0*/) { do_blocking_move_to(rx, current_position[Y_AXIS], current_position[Z_AXIS], fr_mm_s); } +void do_blocking_move_to_y(const float &ry, const float &fr_mm_s/*=0.0*/) { + do_blocking_move_to(current_position[Y_AXIS], ry, current_position[Z_AXIS], fr_mm_s); +} void do_blocking_move_to_z(const float &rz, const float &fr_mm_s/*=0.0*/) { do_blocking_move_to(current_position[X_AXIS], current_position[Y_AXIS], rz, fr_mm_s); } @@ -473,7 +476,7 @@ void clean_up_after_endstop_or_probe_move() { if (axis == X_AXIS) { // In Dual X mode hotend_offset[X] is T1's home position - const float dual_max_x = MAX(hotend_offset[X_AXIS][1], X2_MAX_POS); + const float dual_max_x = _MAX(hotend_offset[X_AXIS][1], X2_MAX_POS); if (new_tool_index != 0) { // T1 can move from X2_MIN_POS to X2_MAX_POS or X2 home position (whichever is larger) @@ -484,7 +487,7 @@ void clean_up_after_endstop_or_probe_move() { // In Duplication Mode, T0 can move as far left as X1_MIN_POS // but not so far to the right that T1 would move past the end soft_endstop[X_AXIS].min = X1_MIN_POS; - soft_endstop[X_AXIS].max = MIN(X1_MAX_POS, dual_max_x - duplicate_extruder_x_offset); + soft_endstop[X_AXIS].max = _MIN(X1_MAX_POS, dual_max_x - duplicate_extruder_x_offset); } else { // In other modes, T0 can move from X1_MIN_POS to X1_MAX_POS @@ -507,7 +510,7 @@ void clean_up_after_endstop_or_probe_move() { case X_AXIS: case Y_AXIS: // Get a minimum radius for clamping - delta_max_radius = MIN(ABS(MAX(soft_endstop[X_AXIS].min, soft_endstop[Y_AXIS].min)), soft_endstop[X_AXIS].max, soft_endstop[Y_AXIS].max); + delta_max_radius = _MIN(ABS(_MAX(soft_endstop[X_AXIS].min, soft_endstop[Y_AXIS].min)), soft_endstop[X_AXIS].max, soft_endstop[Y_AXIS].max); delta_max_radius_2 = sq(delta_max_radius); break; case Z_AXIS: @@ -538,10 +541,8 @@ void clean_up_after_endstop_or_probe_move() { #endif - #if ENABLED(DEBUG_LEVELING_FEATURE) - if (DEBUGGING(LEVELING)) - SERIAL_ECHOLNPAIR("Axis ", axis_codes[axis], " min:", soft_endstop[axis].min, " max:", soft_endstop[axis].max); - #endif + if (DEBUGGING(LEVELING)) + SERIAL_ECHOLNPAIR("Axis ", axis_codes[axis], " min:", soft_endstop[axis].min, " max:", soft_endstop[axis].max); } /** @@ -1044,7 +1045,7 @@ bool axis_unhomed_error(const bool x/*=true*/, const bool y/*=true*/, const bool if (zz) SERIAL_CHAR('Z'); SERIAL_ECHOLNPGM(" " MSG_FIRST); - #if EITHER(ULTRA_LCD, EXTENSIBLE_UI) + #if HAS_DISPLAY ui.status_printf_P(0, PSTR(MSG_HOME " %s%s%s " MSG_FIRST), xx ? MSG_X : "", yy ? MSG_Y : "", zz ? MSG_Z : ""); #endif return true; @@ -1073,7 +1074,7 @@ float get_homing_bump_feedrate(const AxisEnum axis) { * Set sensorless homing if the axis has it, accounting for Core Kinematics. */ sensorless_t start_sensorless_homing_per_axis(const AxisEnum axis) { - sensorless_t stealth_states { false, false, false, false, false, false, false }; + sensorless_t stealth_states { false }; switch (axis) { default: break; @@ -1441,7 +1442,7 @@ void homeaxis(const AxisEnum axis) { // When homing Z with probe respect probe clearance const float bump = axis_home_dir * ( #if HOMING_Z_WITH_PROBE - (axis == Z_AXIS && (Z_HOME_BUMP_MM)) ? MAX(Z_CLEARANCE_BETWEEN_PROBES, Z_HOME_BUMP_MM) : + (axis == Z_AXIS && (Z_HOME_BUMP_MM)) ? _MAX(Z_CLEARANCE_BETWEEN_PROBES, Z_HOME_BUMP_MM) : #endif home_bump_mm(axis) ); @@ -1601,6 +1602,21 @@ void homeaxis(const AxisEnum axis) { if (axis == Z_AXIS && STOW_PROBE()) return; #endif + #ifdef HOMING_BACKOFF_MM + constexpr float endstop_backoff[XYZ] = HOMING_BACKOFF_MM; + const float backoff_mm = endstop_backoff[ + #if ENABLED(DELTA) + Z_AXIS + #else + axis + #endif + ]; + if (backoff_mm) { + current_position[axis] -= ABS(backoff_mm) * axis_home_dir; + line_to_current_position(); + } + #endif + // Clear retracted status if homing the Z axis #if ENABLED(FWRETRACT) if (axis == Z_AXIS) fwretract.current_hop = 0.0; diff --git a/Marlin/src/module/motion.h b/Marlin/src/module/motion.h index 35819187ae..7c637f9cb8 100644 --- a/Marlin/src/module/motion.h +++ b/Marlin/src/module/motion.h @@ -27,7 +27,6 @@ * High-level motion commands to feed the planner * Some of these methods may migrate to the planner class. */ -#pragma once #include "../inc/MarlinConfig.h" @@ -186,6 +185,7 @@ void prepare_move_to_destination(); */ void do_blocking_move_to(const float rx, const float ry, const float rz, const float &fr_mm_s=0); void do_blocking_move_to_x(const float &rx, const float &fr_mm_s=0); +void do_blocking_move_to_y(const float &ry, const float &fr_mm_s=0); void do_blocking_move_to_z(const float &rz, const float &fr_mm_s=0); void do_blocking_move_to_xy(const float &rx, const float &ry, const float &fr_mm_s=0); diff --git a/Marlin/src/module/planner.cpp b/Marlin/src/module/planner.cpp index 6f531c7208..b8bc07069e 100644 --- a/Marlin/src/module/planner.cpp +++ b/Marlin/src/module/planner.cpp @@ -212,7 +212,7 @@ float Planner::previous_speed[NUM_AXIS], float Planner::position_cart[XYZE]; #endif -#if ENABLED(ULTRA_LCD) +#if HAS_SPI_LCD volatile uint32_t Planner::block_buffer_runtime_us = 0; #endif @@ -733,7 +733,7 @@ void Planner::calculate_trapezoid_for_block(block_t* const block, const float &e // reach the final_rate exactly at the end of this block. if (plateau_steps < 0) { const float accelerate_steps_float = CEIL(intersection_distance(initial_rate, final_rate, accel, block->step_event_count)); - accelerate_steps = MIN(uint32_t(MAX(accelerate_steps_float, 0)), block->step_event_count); + accelerate_steps = _MIN(uint32_t(_MAX(accelerate_steps_float, 0)), block->step_event_count); plateau_steps = 0; #if ENABLED(S_CURVE_ACCELERATION) @@ -855,7 +855,7 @@ void Planner::reverse_pass_kernel(block_t* const current, const block_t * const const float new_entry_speed_sqr = TEST(current->flag, BLOCK_BIT_NOMINAL_LENGTH) ? max_entry_speed_sqr - : MIN(max_entry_speed_sqr, max_allowable_speed_sqr(-current->acceleration, next ? next->entry_speed_sqr : sq(float(MINIMUM_PLANNER_SPEED)), current->millimeters)); + : _MIN(max_entry_speed_sqr, max_allowable_speed_sqr(-current->acceleration, next ? next->entry_speed_sqr : sq(float(MINIMUM_PLANNER_SPEED)), current->millimeters)); if (current->entry_speed_sqr != new_entry_speed_sqr) { // Need to recalculate the block speed - Mark it now, so the stepper @@ -1157,7 +1157,7 @@ void Planner::recalculate() { } float t = autotemp_min + high * autotemp_factor; - t = constrain(t, autotemp_min, autotemp_max); + LIMIT(t, autotemp_min, autotemp_max); if (t < oldt) t = t * (1 - float(AUTOTEMP_OLDWEIGHT)) + oldt * float(AUTOTEMP_OLDWEIGHT); oldt = t; thermalManager.setTargetHotend(t, 0); @@ -1469,7 +1469,7 @@ void Planner::quick_stop() { // forced to empty, there's no risk the ISR will touch this. delay_before_delivering = BLOCK_DELAY_FOR_1ST_MOVE; - #if ENABLED(ULTRA_LCD) + #if HAS_SPI_LCD // Clear the accumulated runtime clear_block_buffer_runtime(); #endif @@ -1817,7 +1817,7 @@ bool Planner::_populate_block(block_t * const block, bool split_move, } block->steps[E_AXIS] = esteps; - block->step_event_count = MAX(block->steps[A_AXIS], block->steps[B_AXIS], block->steps[C_AXIS], esteps); + block->step_event_count = _MAX(block->steps[A_AXIS], block->steps[B_AXIS], block->steps[C_AXIS], esteps); // Bail if this is a zero-length block if (block->step_event_count < MIN_STEPS_PER_SEGMENT) return false; @@ -2024,14 +2024,14 @@ bool Planner::_populate_block(block_t * const block, bool split_move, // buffer is draining, add extra time. The amount of time added increases if the buffer is still emptied more. const uint32_t nst = segment_time_us + LROUND(2 * (settings.min_segment_time_us - segment_time_us) / moves_queued); inverse_secs = 1000000.0f / nst; - #if defined(XY_FREQUENCY_LIMIT) || ENABLED(ULTRA_LCD) + #if defined(XY_FREQUENCY_LIMIT) || HAS_SPI_LCD segment_time_us = nst; #endif } } #endif - #if ENABLED(ULTRA_LCD) + #if HAS_SPI_LCD // Protect the access to the position. const bool was_enabled = STEPPER_ISR_ENABLED(); if (was_enabled) DISABLE_STEPPER_DRIVER_INTERRUPT(); @@ -2128,9 +2128,9 @@ bool Planner::_populate_block(block_t * const block, bool split_move, } ys0 = axis_segment_time_us[Y_AXIS][0] = ys0 + segment_time_us; - const uint32_t max_x_segment_time = MAX(xs0, xs1, xs2), - max_y_segment_time = MAX(ys0, ys1, ys2), - min_xy_segment_time = MIN(max_x_segment_time, max_y_segment_time); + const uint32_t max_x_segment_time = _MAX(xs0, xs1, xs2), + max_y_segment_time = _MAX(ys0, ys1, ys2), + min_xy_segment_time = _MIN(max_x_segment_time, max_y_segment_time); if (min_xy_segment_time < MAX_FREQ_TIME_US) { const float low_sf = speed_factor * min_xy_segment_time / (MAX_FREQ_TIME_US); NOMORE(speed_factor, low_sf); @@ -2370,7 +2370,7 @@ bool Planner::_populate_block(block_t * const block, bool split_move, } // Get the lowest speed - vmax_junction_sqr = MIN(vmax_junction_sqr, block->nominal_speed_sqr, previous_nominal_speed_sqr); + vmax_junction_sqr = _MIN(vmax_junction_sqr, block->nominal_speed_sqr, previous_nominal_speed_sqr); } else // Init entry speed to zero. Assume it starts from rest. Planner will correct this later. vmax_junction_sqr = 0; @@ -2427,7 +2427,7 @@ bool Planner::_populate_block(block_t * const block, bool split_move, // The junction velocity will be shared between successive segments. Limit the junction velocity to their minimum. // Pick the smaller of the nominal speeds. Higher speed shall not be achieved at the junction during coasting. const float previous_nominal_speed = SQRT(previous_nominal_speed_sqr); - vmax_junction = MIN(nominal_speed, previous_nominal_speed); + vmax_junction = _MIN(nominal_speed, previous_nominal_speed); // Now limit the jerk in all axes. const float smaller_speed_factor = vmax_junction / previous_nominal_speed; @@ -2448,9 +2448,9 @@ bool Planner::_populate_block(block_t * const block, bool split_move, // Calculate jerk depending on whether the axis is coasting in the same direction or reversing. const float jerk = (v_exit > v_entry) ? // coasting axis reversal - ( (v_entry > 0 || v_exit < 0) ? (v_exit - v_entry) : MAX(v_exit, -v_entry) ) + ( (v_entry > 0 || v_exit < 0) ? (v_exit - v_entry) : _MAX(v_exit, -v_entry) ) : // v_exit <= v_entry coasting axis reversal - ( (v_entry < 0 || v_exit > 0) ? (v_entry - v_exit) : MAX(-v_exit, v_entry) ); + ( (v_entry < 0 || v_exit > 0) ? (v_entry - v_exit) : _MAX(-v_exit, v_entry) ); if (jerk > max_jerk[axis]) { v_factor *= max_jerk[axis] / jerk; @@ -2470,7 +2470,7 @@ bool Planner::_populate_block(block_t * const block, bool split_move, previous_safe_speed = safe_speed; #if ENABLED(JUNCTION_DEVIATION) - vmax_junction_sqr = MIN(vmax_junction_sqr, sq(vmax_junction)); + vmax_junction_sqr = _MIN(vmax_junction_sqr, sq(vmax_junction)); #else vmax_junction_sqr = sq(vmax_junction); #endif @@ -2485,7 +2485,7 @@ bool Planner::_populate_block(block_t * const block, bool split_move, // If we are trying to add a split block, start with the // max. allowed speed to avoid an interrupted first move. - block->entry_speed_sqr = !split_move ? sq(float(MINIMUM_PLANNER_SPEED)) : MIN(vmax_junction_sqr, v_allowable_sqr); + block->entry_speed_sqr = !split_move ? sq(float(MINIMUM_PLANNER_SPEED)) : _MIN(vmax_junction_sqr, v_allowable_sqr); // Initialize planner efficiency flags // Set flag if block will always reach maximum junction speed regardless of entry/exit speeds. diff --git a/Marlin/src/module/planner.h b/Marlin/src/module/planner.h index 679ecbe8a3..9df4820576 100644 --- a/Marlin/src/module/planner.h +++ b/Marlin/src/module/planner.h @@ -334,7 +334,7 @@ class Planner { static uint32_t axis_segment_time_us[2][3]; #endif - #if ENABLED(ULTRA_LCD) + #if HAS_SPI_LCD volatile static uint32_t block_buffer_runtime_us; //Theoretical block buffer runtime in µs #endif @@ -773,7 +773,7 @@ class Planner { // No trapezoid calculated? Don't execute yet. if (TEST(block->flag, BLOCK_BIT_RECALCULATE)) return nullptr; - #if ENABLED(ULTRA_LCD) + #if HAS_SPI_LCD block_buffer_runtime_us -= block->segment_time_us; // We can't be sure how long an active block will take, so don't count it. #endif @@ -789,7 +789,7 @@ class Planner { } // The queue became empty - #if ENABLED(ULTRA_LCD) + #if HAS_SPI_LCD clear_block_buffer_runtime(); // paranoia. Buffer is empty now - so reset accumulated time to zero. #endif @@ -806,7 +806,7 @@ class Planner { block_buffer_tail = next_block_index(block_buffer_tail); } - #if ENABLED(ULTRA_LCD) + #if HAS_SPI_LCD static uint16_t block_buffer_runtime() { #ifdef __AVR__ @@ -948,6 +948,6 @@ class Planner { #endif // JUNCTION_DEVIATION }; -#define PLANNER_XY_FEEDRATE() (MIN(planner.settings.max_feedrate_mm_s[X_AXIS], planner.settings.max_feedrate_mm_s[Y_AXIS])) +#define PLANNER_XY_FEEDRATE() (_MIN(planner.settings.max_feedrate_mm_s[X_AXIS], planner.settings.max_feedrate_mm_s[Y_AXIS])) extern Planner planner; diff --git a/Marlin/src/module/printcounter.cpp b/Marlin/src/module/printcounter.cpp index 09fb0eb970..25e8a767ab 100644 --- a/Marlin/src/module/printcounter.cpp +++ b/Marlin/src/module/printcounter.cpp @@ -246,13 +246,13 @@ void PrintCounter::tick() { data.printTime += delta; #if SERVICE_INTERVAL_1 > 0 - data.nextService1 -= MIN(delta, data.nextService1); + data.nextService1 -= _MIN(delta, data.nextService1); #endif #if SERVICE_INTERVAL_2 > 0 - data.nextService2 -= MIN(delta, data.nextService2); + data.nextService2 -= _MIN(delta, data.nextService2); #endif #if SERVICE_INTERVAL_3 > 0 - data.nextService3 -= MIN(delta, data.nextService3); + data.nextService3 -= _MIN(delta, data.nextService3); #endif update_next = now + updateInterval * 1000; diff --git a/Marlin/src/module/probe.cpp b/Marlin/src/module/probe.cpp index 810f20be70..4e7436a634 100644 --- a/Marlin/src/module/probe.cpp +++ b/Marlin/src/module/probe.cpp @@ -108,7 +108,7 @@ float zprobe_zoffset; // Initialized by settings.load() // Move to the magnet to unlock the probe void run_deploy_moves_script() { #ifndef TOUCH_MI_DEPLOY_XPOS - #define TOUCH_MI_DEPLOY_XPOS 0 + #define TOUCH_MI_DEPLOY_XPOS X_MIN_POS #elif TOUCH_MI_DEPLOY_XPOS > X_MAX_BED TemporaryGlobalEndstopsState unlock_x(false); #endif @@ -319,7 +319,7 @@ float zprobe_zoffset; // Initialized by settings.load() #endif #if ENABLED(PROBING_STEPPERS_OFF) disable_e_steppers(); - #if DISABLED(DELTA, HOME_AFTER_DEACTIVATE) + #if NONE(DELTA, HOME_AFTER_DEACTIVATE) disable_X(); disable_Y(); #endif #endif @@ -444,7 +444,7 @@ bool set_probe_deployed(const bool deploy) { #endif if (deploy_stow_condition && unknown_condition) - do_probe_raise(MAX(Z_CLEARANCE_BETWEEN_PROBES, Z_CLEARANCE_DEPLOY_PROBE)); + do_probe_raise(_MAX(Z_CLEARANCE_BETWEEN_PROBES, Z_CLEARANCE_DEPLOY_PROBE)); #if EITHER(Z_PROBE_SLED, Z_PROBE_ALLEN_KEY) #if ENABLED(Z_PROBE_SLED) @@ -540,7 +540,7 @@ static bool do_probe_move(const float z, const float fr_mm_s) { // Disable stealthChop if used. Enable diag1 pin on driver. #if ENABLED(SENSORLESS_PROBING) - sensorless_t stealth_states { false, false, false, false, false, false, false }; + sensorless_t stealth_states { false }; #if ENABLED(DELTA) stealth_states.x = tmc_enable_stallguard(stepperX); stealth_states.y = tmc_enable_stallguard(stepperY); @@ -780,7 +780,7 @@ float probe_pt(const float &rx, const float &ry, const ProbePtRaise raise_after/ const float nz = #if ENABLED(DELTA) // Move below clip height or xy move will be aborted by do_blocking_move_to - MIN(current_position[Z_AXIS], delta_clip_start_height) + _MIN(current_position[Z_AXIS], delta_clip_start_height) #else current_position[Z_AXIS] #endif diff --git a/Marlin/src/module/scara.h b/Marlin/src/module/scara.h index 44f07026e3..3a17cddbfd 100644 --- a/Marlin/src/module/scara.h +++ b/Marlin/src/module/scara.h @@ -25,8 +25,6 @@ * scara.h - SCARA-specific functions */ -#pragma once - #include "../core/macros.h" extern float delta_segments_per_second; diff --git a/Marlin/src/module/stepper.cpp b/Marlin/src/module/stepper.cpp index a5c73bb3ff..3d2c34e6d3 100644 --- a/Marlin/src/module/stepper.cpp +++ b/Marlin/src/module/stepper.cpp @@ -1291,7 +1291,7 @@ void Stepper::isr() { uint32_t interval = #if ENABLED(LIN_ADVANCE) - MIN(nextAdvanceISR, nextMainISR) // Nearest time interval + _MIN(nextAdvanceISR, nextMainISR) // Nearest time interval #else nextMainISR // Remaining stepper ISR time #endif @@ -1404,7 +1404,7 @@ void Stepper::stepper_pulse_phase_isr() { // Count of pending loops and events for this iteration const uint32_t pending_events = step_event_count - step_events_completed; - uint8_t events_to_do = MIN(pending_events, steps_per_isr); + uint8_t events_to_do = _MIN(pending_events, steps_per_isr); // Just update the value we will get at the end of the loop step_events_completed += events_to_do; diff --git a/Marlin/src/module/stepper.h b/Marlin/src/module/stepper.h index 7e8b9c5e0d..eca4a75c17 100644 --- a/Marlin/src/module/stepper.h +++ b/Marlin/src/module/stepper.h @@ -151,7 +151,7 @@ #define MIN_ISR_LOOP_CYCLES (ISR_X_STEPPER_CYCLES + ISR_Y_STEPPER_CYCLES + ISR_Z_STEPPER_CYCLES + ISR_E_STEPPER_CYCLES + ISR_MIXING_STEPPER_CYCLES) // Calculate the minimum MPU cycles needed per pulse to enforce, limited to the max stepper rate -#define _MIN_STEPPER_PULSE_CYCLES(N) MAX(uint32_t((F_CPU) / (MAXIMUM_STEPPER_RATE)), ((F_CPU) / 500000UL) * (N)) +#define _MIN_STEPPER_PULSE_CYCLES(N) _MAX(uint32_t((F_CPU) / (MAXIMUM_STEPPER_RATE)), ((F_CPU) / 500000UL) * (N)) #if MINIMUM_STEPPER_PULSE #define MIN_STEPPER_PULSE_CYCLES _MIN_STEPPER_PULSE_CYCLES(uint32_t(MINIMUM_STEPPER_PULSE)) #elif HAS_DRIVER(LV8729) @@ -174,7 +174,7 @@ #define ADDED_STEP_TICKS (((MIN_STEPPER_PULSE_CYCLES) / (PULSE_TIMER_PRESCALE)) - (MIN_PULSE_TICKS)) // But the user could be enforcing a minimum time, so the loop time is -#define ISR_LOOP_CYCLES (ISR_LOOP_BASE_CYCLES + MAX(MIN_STEPPER_PULSE_CYCLES, MIN_ISR_LOOP_CYCLES)) +#define ISR_LOOP_CYCLES (ISR_LOOP_BASE_CYCLES + _MAX(MIN_STEPPER_PULSE_CYCLES, MIN_ISR_LOOP_CYCLES)) // If linear advance is enabled, then it is handled separately #if ENABLED(LIN_ADVANCE) @@ -192,7 +192,7 @@ #endif // And the real loop time - #define ISR_LA_LOOP_CYCLES MAX(MIN_STEPPER_PULSE_CYCLES, MIN_ISR_LA_LOOP_CYCLES) + #define ISR_LA_LOOP_CYCLES _MAX(MIN_STEPPER_PULSE_CYCLES, MIN_ISR_LA_LOOP_CYCLES) #else #define ISR_LA_LOOP_CYCLES 0UL diff --git a/Marlin/src/module/stepper_indirection.cpp b/Marlin/src/module/stepper_indirection.cpp index 362ed01ba9..786cb1db8f 100644 --- a/Marlin/src/module/stepper_indirection.cpp +++ b/Marlin/src/module/stepper_indirection.cpp @@ -45,8 +45,8 @@ #if HAS_DRIVER(TMC26X) #include - #ifdef STM32F7 - #include "../HAL/HAL_STM32F7/TMC2660.h" + #if defined(STM32GENERIC) && defined(STM32F7) + #include "../HAL/HAL_STM32_F4_F7/STM32F7/TMC2660.h" #else #include #endif @@ -309,7 +309,7 @@ // // TMC2208/2209 Driver objects and inits // -#if HAS_DRIVER(TMC2208) || HAS_DRIVER(TMC2209) +#if HAS_TMC220x #if AXIS_HAS_UART(X) #ifdef X_HARDWARE_SERIAL TMC_UART_DEFINE(HW, X, X); diff --git a/Marlin/src/module/stepper_indirection.h b/Marlin/src/module/stepper_indirection.h index 0e9c188adc..b0688a9a08 100644 --- a/Marlin/src/module/stepper_indirection.h +++ b/Marlin/src/module/stepper_indirection.h @@ -35,8 +35,8 @@ // TMC26X drivers have STEP/DIR on normal pins, but ENABLE via SPI #if HAS_DRIVER(TMC26X) #include - #ifdef STM32F7 - #include "../HAL/HAL_STM32F7/TMC2660.h" + #if defined(STM32GENERIC) && defined(STM32F7) + #include "../HAL/HAL_STM32_F4_F7/STM32F7/TMC2660.h" #else #include #endif @@ -69,7 +69,7 @@ static constexpr chopper_timing_t chopper_timing = CHOPPER_TIMING; - #if HAS_DRIVER(TMC2208) || HAS_DRIVER(TMC2209) + #if HAS_TMC220x void tmc_serial_begin(); #endif #endif diff --git a/Marlin/src/module/temperature.cpp b/Marlin/src/module/temperature.cpp index 16ae6b996c..812a4739b6 100644 --- a/Marlin/src/module/temperature.cpp +++ b/Marlin/src/module/temperature.cpp @@ -33,7 +33,7 @@ #include "../core/language.h" #include "../HAL/shared/Delay.h" -#define MAX6675_SEPARATE_SPI EITHER(HEATER_0_USES_MAX6675, HEATER_1_USES_MAX6675) && PIN_EXISTS(MAX6675_SCK, MAX6675_DO) +#define MAX6675_SEPARATE_SPI (EITHER(HEATER_0_USES_MAX6675, HEATER_1_USES_MAX6675) && PIN_EXISTS(MAX6675_SCK, MAX6675_DO)) #if MAX6675_SEPARATE_SPI #include "../libs/private_spi.h" @@ -68,7 +68,7 @@ #include "tool_change.h" #endif -#if HAS_BUZZER +#if HAS_BUZZER && PIN_EXISTS(BEEPER) #include "../libs/buzzer.h" #endif @@ -143,7 +143,7 @@ hotend_info_t Temperature::temp_hotend[HOTENDS set_fan_speed(fan, new_fan_speed[fan]); break; default: - new_fan_speed[fan] = MIN(tmp_temp, 255U); + new_fan_speed[fan] = _MIN(tmp_temp, 255U); break; } } @@ -163,7 +163,7 @@ hotend_info_t Temperature::temp_hotend[HOTENDS uint8_t Temperature::lcd_tmpfan_speed[ #if ENABLED(SINGLENOZZLE) - MAX(EXTRUDERS, FAN_COUNT) + _MAX(EXTRUDERS, FAN_COUNT) #else FAN_COUNT #endif @@ -460,7 +460,7 @@ temp_range_t Temperature::temp_range[HOTENDS] = ARRAY_BY_HOTENDS(sensor_heater_0 if (cycles > 0) { const long max_pow = GHV(MAX_BED_POWER, PID_MAX); bias += (d * (t_high - t_low)) / (t_low + t_high); - bias = constrain(bias, 20, max_pow - 20); + LIMIT(bias, 20, max_pow - 20); d = (bias > max_pow >> 1) ? max_pow - 1 - bias : bias; SERIAL_ECHOPAIR(MSG_BIAS, bias, MSG_D, d, MSG_T_MIN, min, MSG_T_MAX, max); @@ -469,12 +469,23 @@ temp_range_t Temperature::temp_range[HOTENDS] = ARRAY_BY_HOTENDS(sensor_heater_0 Tu = float(t_low + t_high) * 0.001f, pf = isbed ? 0.2f : 0.6f, df = isbed ? 1.0f / 3.0f : 1.0f / 8.0f; - tune_pid.Kp = Ku * pf; - tune_pid.Kd = tune_pid.Kp * Tu * df; - tune_pid.Ki = 2 * tune_pid.Kp / Tu; + SERIAL_ECHOPAIR(MSG_KU, Ku, MSG_TU, Tu); - SERIAL_ECHOLNPGM("\n" MSG_CLASSIC_PID); - SERIAL_ECHOLNPAIR(MSG_KP, tune_pid.Kp, MSG_KI, tune_pid.Ki, MSG_KD, tune_pid.Kd); + if (isbed) { // Do not remove this otherwise PID autotune won't work right for the bed! + tune_pid.Kp = Ku * 0.2f; + tune_pid.Ki = 2 * tune_pid.Kp / Tu; + tune_pid.Kd = tune_pid.Kp * Tu / 3; + SERIAL_ECHOLNPGM("\n" " No overshoot"); // Works far better for the bed. Classic and some have bad ringing. + SERIAL_ECHOLNPAIR(MSG_KP, tune_pid.Kp, MSG_KI, tune_pid.Ki, MSG_KD, tune_pid.Kd); + } + else { + tune_pid.Kp = Ku * pf; + tune_pid.Kd = tune_pid.Kp * Tu * df; + tune_pid.Ki = 2 * tune_pid.Kp / Tu; + SERIAL_ECHOLNPGM("\n" MSG_CLASSIC_PID); + SERIAL_ECHOLNPAIR(MSG_KP, tune_pid.Kp, MSG_KI, tune_pid.Ki, MSG_KD, tune_pid.Kd); + } + /** tune_pid.Kp = 0.33 * Ku; tune_pid.Ki = tune_pid.Kp / Tu; @@ -746,9 +757,28 @@ int16_t Temperature::getHeaterPower(const heater_ind_t heater_id) { // // Temperature Error Handlers // + +inline void loud_kill(PGM_P const lcd_msg) { + Running = false; + #if HAS_BUZZER && PIN_EXISTS(BEEPER) + for (uint8_t i = 20; i--;) { + WRITE(BEEPER_PIN, HIGH); delay(25); + WRITE(BEEPER_PIN, LOW); delay(80); + } + WRITE(BEEPER_PIN, HIGH); + #endif + kill(lcd_msg); +} + void Temperature::_temp_error(const heater_ind_t heater, PGM_P const serial_msg, PGM_P const lcd_msg) { - static bool killed = false; - if (IsRunning()) { + + static uint8_t killed = 0; + + if (IsRunning() + #if BOGUS_TEMPERATURE_GRACE_PERIOD + && killed == 2 + #endif + ) { SERIAL_ERROR_START(); serialprintPGM(serial_msg); SERIAL_ECHOPGM(MSG_STOPPED_HEATER); @@ -760,27 +790,28 @@ void Temperature::_temp_error(const heater_ind_t heater, PGM_P const serial_msg, SERIAL_EOL(); } - #if DISABLED(BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE) - if (!killed) { - Running = false; - killed = true; + disable_all_heaters(); // always disable (even for bogus temp) - disable_all_heaters(); - - #if HAS_BUZZER && PIN_EXISTS(BEEPER) - for (uint8_t i = 20; i--;) { - WRITE(BEEPER_PIN, HIGH); delay(25); - WRITE(BEEPER_PIN, LOW); delay(80); - } - WRITE(BEEPER_PIN, HIGH); - #endif - - kill(lcd_msg); + #if BOGUS_TEMPERATURE_GRACE_PERIOD + const millis_t ms = millis(); + static millis_t expire_ms; + switch (killed) { + case 0: + expire_ms = ms + BOGUS_TEMPERATURE_GRACE_PERIOD; + ++killed; + break; + case 1: + if (ELAPSED(ms, expire_ms)) ++killed; + break; + case 2: + loud_kill(lcd_msg); + ++killed; + break; } - else - disable_all_heaters(); // paranoia - #else + #elif defined(BOGUS_TEMPERATURE_GRACE_PERIOD) UNUSED(killed); + #else + if (!killed) { killed = 1; loud_kill(lcd_msg); } #endif } @@ -830,12 +861,12 @@ float Temperature::get_pid_output_hotend(const uint8_t e) { } work_pid[ee].Kd = work_pid[ee].Kd + PID_K2 * (PID_PARAM(Kd, ee) * (temp_dState[ee] - temp_hotend[ee].current) - work_pid[ee].Kd); - const float max_power_over_i_gain = (float)PID_MAX / PID_PARAM(Ki, ee); + const float max_power_over_i_gain = float(PID_MAX) / PID_PARAM(Ki, ee) - float(MIN_POWER); temp_iState[ee] = constrain(temp_iState[ee] + pid_error, 0, max_power_over_i_gain); work_pid[ee].Kp = PID_PARAM(Kp, ee) * pid_error; work_pid[ee].Ki = PID_PARAM(Ki, ee) * temp_iState[ee]; - pid_output = work_pid[ee].Kp + work_pid[ee].Ki + work_pid[ee].Kd; + pid_output = work_pid[ee].Kp + work_pid[ee].Ki + work_pid[ee].Kd + float(MIN_POWER); #if ENABLED(PID_EXTRUSION_SCALING) work_pid[ee].Kc = 0; @@ -854,7 +885,7 @@ float Temperature::get_pid_output_hotend(const uint8_t e) { } #endif // PID_EXTRUSION_SCALING - pid_output = constrain(pid_output, 0, PID_MAX); + LIMIT(pid_output, 0, PID_MAX); } temp_dState[ee] = temp_hotend[ee].current; @@ -865,23 +896,25 @@ float Temperature::get_pid_output_hotend(const uint8_t e) { #endif // PID_OPENLOOP #if ENABLED(PID_DEBUG) - SERIAL_ECHO_START(); - SERIAL_ECHOPAIR( - MSG_PID_DEBUG, ee, - MSG_PID_DEBUG_INPUT, temp_hotend[ee].current, - MSG_PID_DEBUG_OUTPUT, pid_output - ); - #if DISABLED(PID_OPENLOOP) + if (e == active_extruder) { + SERIAL_ECHO_START(); SERIAL_ECHOPAIR( - MSG_PID_DEBUG_PTERM, work_pid[ee].Kp, - MSG_PID_DEBUG_ITERM, work_pid[ee].Ki, - MSG_PID_DEBUG_DTERM, work_pid[ee].Kd - #if ENABLED(PID_EXTRUSION_SCALING) - , MSG_PID_DEBUG_CTERM, work_pid[ee].Kc - #endif + MSG_PID_DEBUG, ee, + MSG_PID_DEBUG_INPUT, temp_hotend[ee].current, + MSG_PID_DEBUG_OUTPUT, pid_output ); - #endif - SERIAL_EOL(); + #if DISABLED(PID_OPENLOOP) + SERIAL_ECHOPAIR( + MSG_PID_DEBUG_PTERM, work_pid[ee].Kp, + MSG_PID_DEBUG_ITERM, work_pid[ee].Ki, + MSG_PID_DEBUG_DTERM, work_pid[ee].Kd + #if ENABLED(PID_EXTRUSION_SCALING) + , MSG_PID_DEBUG_CTERM, work_pid[ee].Kc + #endif + ); + #endif + SERIAL_EOL(); + } #endif // PID_DEBUG #else // No PID enabled @@ -907,19 +940,36 @@ float Temperature::get_pid_output_hotend(const uint8_t e) { static PID_t work_pid = { 0 }; static float temp_iState = 0, temp_dState = 0; - - const float max_power_over_i_gain = (float)MAX_BED_POWER / temp_bed.pid.Ki, + static bool pid_reset = true; + float pid_output = 0; + const float max_power_over_i_gain = float(MAX_BED_POWER) / temp_bed.pid.Ki - float(MIN_BED_POWER), pid_error = temp_bed.target - temp_bed.current; - temp_iState = constrain(temp_iState + pid_error, 0, max_power_over_i_gain); + if (!temp_bed.target || pid_error < -(PID_FUNCTIONAL_RANGE)) { + pid_output = 0; + pid_reset = true; + } + else if (pid_error > PID_FUNCTIONAL_RANGE) { + pid_output = BANG_MAX; + pid_reset = true; + } + else { + if (pid_reset) { + temp_iState = 0.0; + work_pid.Kd = 0.0; + pid_reset = false; + } - work_pid.Kp = temp_bed.pid.Kp * pid_error; - work_pid.Ki = temp_bed.pid.Ki * temp_iState; - work_pid.Kd = work_pid.Kd + PID_K2 * (temp_bed.pid.Kd * (temp_dState - temp_bed.current) - work_pid.Kd); + temp_iState = constrain(temp_iState + pid_error, 0, max_power_over_i_gain); - temp_dState = temp_bed.current; + work_pid.Kp = temp_bed.pid.Kp * pid_error; + work_pid.Ki = temp_bed.pid.Ki * temp_iState; + work_pid.Kd = work_pid.Kd + PID_K2 * (temp_bed.pid.Kd * (temp_dState - temp_bed.current) - work_pid.Kd); - const float pid_output = constrain(work_pid.Kp + work_pid.Ki + work_pid.Kd, 0, MAX_BED_POWER); + temp_dState = temp_bed.current; + + pid_output = constrain(work_pid.Kp + work_pid.Ki + work_pid.Kd + float(MIN_BED_POWER), 0, MAX_BED_POWER); + } #else // PID_OPENLOOP @@ -957,10 +1007,7 @@ void Temperature::manage_heater() { #if EARLY_WATCHDOG // If thermal manager is still not running, make sure to at least reset the watchdog! - if (!inited) { - watchdog_reset(); - return; - } + if (!inited) return watchdog_reset(); #endif #if BOTH(PROBING_HEATERS_OFF, BED_LIMIT_SWITCHING) @@ -976,17 +1023,15 @@ void Temperature::manage_heater() { updateTemperaturesFromRawValues(); // also resets the watchdog #if ENABLED(HEATER_0_USES_MAX6675) - if (temp_hotend[0].current > MIN(HEATER_0_MAXTEMP, HEATER_0_MAX6675_TMAX - 1.0)) max_temp_error(H_E0); - if (temp_hotend[0].current < MAX(HEATER_0_MINTEMP, HEATER_0_MAX6675_TMIN + .01)) min_temp_error(H_E0); + if (temp_hotend[0].current > _MIN(HEATER_0_MAXTEMP, HEATER_0_MAX6675_TMAX - 1.0)) max_temp_error(H_E0); + if (temp_hotend[0].current < _MAX(HEATER_0_MINTEMP, HEATER_0_MAX6675_TMIN + .01)) min_temp_error(H_E0); #endif #if ENABLED(HEATER_1_USES_MAX6675) - if (temp_hotend[1].current > MIN(HEATER_1_MAXTEMP, HEATER_1_MAX6675_TMAX - 1.0)) max_temp_error(H_E1); - if (temp_hotend[1].current < MAX(HEATER_1_MINTEMP, HEATER_1_MAX6675_TMIN + .01)) min_temp_error(H_E1); + if (temp_hotend[1].current > _MIN(HEATER_1_MAXTEMP, HEATER_1_MAX6675_TMAX - 1.0)) max_temp_error(H_E1); + if (temp_hotend[1].current < _MAX(HEATER_1_MINTEMP, HEATER_1_MAX6675_TMIN + .01)) min_temp_error(H_E1); #endif - #define HAS_THERMAL_PROTECTION (ENABLED(THERMAL_PROTECTION_HOTENDS) || HAS_THERMALLY_PROTECTED_BED || ENABLED(THERMAL_PROTECTION_CHAMBER)) - #if HAS_THERMAL_PROTECTION || DISABLED(PIDTEMPBED) || HAS_AUTO_FAN || HEATER_IDLE_HANDLER millis_t ms = millis(); #endif @@ -1050,7 +1095,7 @@ void Temperature::manage_heater() { if (filament_sensor) { meas_shift_index = filwidth_delay_index[0] - meas_delay_cm; if (meas_shift_index < 0) meas_shift_index += MAX_MEASUREMENT_DELAY + 1; //loop around buffer if needed - meas_shift_index = constrain(meas_shift_index, 0, MAX_MEASUREMENT_DELAY); + LIMIT(meas_shift_index, 0, MAX_MEASUREMENT_DELAY); planner.calculate_volumetric_for_width_sensor(measurement_delay[meas_shift_index]); } #endif // FILAMENT_WIDTH_SENSOR @@ -1325,7 +1370,7 @@ void Temperature::manage_heater() { //#endif // Return degrees C (up to 999, as the LCD only displays 3 digits) - return MIN(value + THERMISTOR_ABS_ZERO_C, 999); + return _MIN(value + THERMISTOR_ABS_ZERO_C, 999); } #endif @@ -1522,7 +1567,11 @@ void Temperature::updateTemperaturesFromRawValues() { #endif // Init fans according to whether they're native PWM or Software PWM -#define _INIT_SOFT_FAN(P) OUT_WRITE(P, FAN_INVERTING ? LOW : HIGH) +#ifdef ALFAWISE_UX0 + #define _INIT_SOFT_FAN(P) OUT_WRITE_OD(P, FAN_INVERTING ? LOW : HIGH) +#else + #define _INIT_SOFT_FAN(P) OUT_WRITE(P, FAN_INVERTING ? LOW : HIGH) +#endif #if ENABLED(FAN_SOFT_PWM) #define _INIT_FAN_PIN(P) _INIT_SOFT_FAN(P) #else @@ -1545,7 +1594,6 @@ void Temperature::updateTemperaturesFromRawValues() { #define INIT_CHAMBER_AUTO_FAN_PIN(P) SET_OUTPUT(P) #endif - /** * Initialize the temperature manager * The manager is implemented by periodic calls to manage_heater() @@ -1572,8 +1620,13 @@ void Temperature::init() { #endif #if HAS_HEATER_0 - OUT_WRITE(HEATER_0_PIN, HEATER_0_INVERTING); + #ifdef ALFAWISE_UX0 + OUT_WRITE_OD(HEATER_0_PIN, HEATER_0_INVERTING); + #else + OUT_WRITE(HEATER_0_PIN, HEATER_0_INVERTING); + #endif #endif + #if HAS_HEATER_1 OUT_WRITE(HEATER_1_PIN, HEATER_1_INVERTING); #endif @@ -1589,9 +1642,15 @@ void Temperature::init() { #if HAS_HEATER_5 OUT_WRITE(HEATER_5_PIN, HEATER_5_INVERTING); #endif + #if HAS_HEATED_BED - OUT_WRITE(HEATER_BED_PIN, HEATER_BED_INVERTING); + #ifdef ALFAWISE_UX0 + OUT_WRITE_OD(HEATER_BED_PIN, HEATER_BED_INVERTING); + #else + OUT_WRITE(HEATER_BED_PIN, HEATER_BED_INVERTING); + #endif #endif + #if HAS_HEATED_CHAMBER OUT_WRITE(HEATER_CHAMBER_PIN, HEATER_CHAMBER_INVERTING); #endif @@ -1655,6 +1714,9 @@ void Temperature::init() { #if ENABLED(FILAMENT_WIDTH_SENSOR) HAL_ANALOG_SELECT(FILWIDTH_PIN); #endif + #if HAS_ADC_BUTTONS + HAL_ANALOG_SELECT(ADC_KEYPAD_PIN); + #endif HAL_timer_start(TEMP_TIMER_NUM, TEMP_TIMER_FREQUENCY); ENABLE_TEMPERATURE_INTERRUPT(); @@ -1884,7 +1946,7 @@ void Temperature::init() { #if ENABLED(ADAPTIVE_FAN_SLOWING) if (adaptive_fan_slowing && heater_id >= 0) { - const int fan_index = MIN(heater_id, FAN_COUNT - 1); + const int fan_index = _MIN(heater_id, FAN_COUNT - 1); if (fan_speed[fan_index] == 0 || current >= tr_target_temperature[heater_id] - (hysteresis_degc * 0.25f)) fan_speed_scaler[fan_index] = 128; else if (current >= tr_target_temperature[heater_id] - (hysteresis_degc * 0.3335f)) @@ -1910,7 +1972,7 @@ void Temperature::init() { } } -#endif // THERMAL_PROTECTION_HOTENDS || THERMAL_PROTECTION_BED || ENABLED(THERMAL_PROTECTION_CHAMBER) +#endif // HAS_THERMAL_PROTECTION void Temperature::disable_all_heaters() { @@ -2891,7 +2953,7 @@ void Temperature::isr() { #endif // AUTO_REPORT_TEMPERATURES - #if EITHER(ULTRA_LCD, EXTENSIBLE_UI) + #if HAS_DISPLAY void Temperature::set_heating_message(const uint8_t e) { const bool heating = isHeatingHotend(e); #if HOTENDS > 1 diff --git a/Marlin/src/module/temperature.h b/Marlin/src/module/temperature.h index 3ea172fe97..becec0770d 100644 --- a/Marlin/src/module/temperature.h +++ b/Marlin/src/module/temperature.h @@ -140,7 +140,7 @@ enum ADCSensorState : char { // get all oversampled sensor readings #define MIN_ADC_ISR_LOOPS 10 -#define ACTUAL_ADC_SAMPLES MAX(int(MIN_ADC_ISR_LOOPS), int(SensorsReady)) +#define ACTUAL_ADC_SAMPLES _MAX(int(MIN_ADC_ISR_LOOPS), int(SensorsReady)) #if HAS_PID_HEATING #define PID_K2 (1-float(PID_K1)) @@ -496,7 +496,7 @@ class Temperature { static uint8_t lcd_tmpfan_speed[ #if ENABLED(SINGLENOZZLE) - MAX(EXTRUDERS, FAN_COUNT) + _MAX(EXTRUDERS, FAN_COUNT) #else FAN_COUNT #endif @@ -613,7 +613,7 @@ class Temperature { #if ENABLED(AUTO_POWER_CONTROL) powerManager.power_on(); #endif - temp_hotend[ee].target = MIN(celsius, temp_range[ee].maxtemp - 15); + temp_hotend[ee].target = _MIN(celsius, temp_range[ee].maxtemp - 15); start_watching_hotend(ee); } @@ -627,7 +627,7 @@ class Temperature { static void setTargetChamber(const int16_t celsius) { temp_chamber.target = #ifdef CHAMBER_MAXTEMP - MIN(celsius, CHAMBER_MAXTEMP) + _MIN(celsius, CHAMBER_MAXTEMP) #else celsius #endif @@ -676,7 +676,7 @@ class Temperature { #endif temp_bed.target = #ifdef BED_MAXTEMP - MIN(celsius, BED_MAXTEMP - 10) + _MIN(celsius, BED_MAXTEMP - 10) #else celsius #endif @@ -785,7 +785,7 @@ class Temperature { #endif #endif - #if EITHER(ULTRA_LCD, EXTENSIBLE_UI) + #if HAS_DISPLAY static void set_heating_message(const uint8_t e); #endif @@ -828,7 +828,9 @@ class Temperature { static void min_temp_error(const heater_ind_t e); static void max_temp_error(const heater_ind_t e); - #if ENABLED(THERMAL_PROTECTION_HOTENDS) || HAS_THERMALLY_PROTECTED_BED || ENABLED(THERMAL_PROTECTION_CHAMBER) + #define HAS_THERMAL_PROTECTION (EITHER(THERMAL_PROTECTION_HOTENDS, THERMAL_PROTECTION_CHAMBER) || HAS_THERMALLY_PROTECTED_BED) + + #if HAS_THERMAL_PROTECTION enum TRState : char { TRInactive, TRFirstHeating, TRStable, TRRunaway }; @@ -849,7 +851,7 @@ class Temperature { static void thermal_runaway_protection(tr_state_machine_t &state, const float ¤t, const float &target, const heater_ind_t heater_id, const uint16_t period_seconds, const uint16_t hysteresis_degc); - #endif // THERMAL_PROTECTION + #endif // HAS_THERMAL_PROTECTION }; extern Temperature thermalManager; diff --git a/Marlin/src/module/thermistor/thermistor_501.h b/Marlin/src/module/thermistor/thermistor_501.h index 6e551641f9..cb178321aa 100644 --- a/Marlin/src/module/thermistor/thermistor_501.h +++ b/Marlin/src/module/thermistor/thermistor_501.h @@ -23,36 +23,36 @@ // 100k Zonestar thermistor. Adjusted By Hally const short temptable_501[][2] PROGMEM = { - {OV( 1), 713}, - {OV( 14), 300}, // Top rating 300C - {OV( 16), 290}, - {OV( 19), 280}, - {OV( 23), 270}, - {OV( 27), 260}, - {OV( 31), 250}, - {OV( 37), 240}, - {OV( 47), 230}, - {OV( 57), 220}, - {OV( 68), 210}, - {OV( 84), 200}, - {OV( 100), 190}, - {OV( 128), 180}, - {OV( 155), 170}, - {OV( 189), 160}, - {OV( 230), 150}, - {OV( 278), 140}, - {OV( 336), 130}, - {OV( 402), 120}, - {OV( 476), 110}, - {OV( 554), 100}, - {OV( 635), 90}, - {OV( 713), 80}, - {OV( 784), 70}, - {OV( 846), 60}, - {OV( 897), 50}, - {OV( 937), 40}, - {OV( 966), 30}, - {OV( 986), 20}, - {OV(1000), 10}, - {OV(1010), 0} + { OV( 1), 713 }, + { OV( 14), 300 }, // Top rating 300C + { OV( 16), 290 }, + { OV( 19), 280 }, + { OV( 23), 270 }, + { OV( 27), 260 }, + { OV( 31), 250 }, + { OV( 37), 240 }, + { OV( 47), 230 }, + { OV( 57), 220 }, + { OV( 68), 210 }, + { OV( 84), 200 }, + { OV( 100), 190 }, + { OV( 128), 180 }, + { OV( 155), 170 }, + { OV( 189), 160 }, + { OV( 230), 150 }, + { OV( 278), 140 }, + { OV( 336), 130 }, + { OV( 402), 120 }, + { OV( 476), 110 }, + { OV( 554), 100 }, + { OV( 635), 90 }, + { OV( 713), 80 }, + { OV( 784), 70 }, + { OV( 846), 60 }, + { OV( 897), 50 }, + { OV( 937), 40 }, + { OV( 966), 30 }, + { OV( 986), 20 }, + { OV(1000), 10 }, + { OV(1010), 0 } }; diff --git a/Marlin/src/module/thermistor/thermistor_512.h b/Marlin/src/module/thermistor/thermistor_512.h new file mode 100644 index 0000000000..aa9e9e57f9 --- /dev/null +++ b/Marlin/src/module/thermistor/thermistor_512.h @@ -0,0 +1,87 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + +// 100k thermistor supplied with RPW-Ultra hotend, 4.7k pullup + +const short temptable_512[][2] PROGMEM = { + { OV(26), 300 }, + { OV(28), 295 }, + { OV(30), 290 }, + { OV(32), 285 }, + { OV(34), 280 }, + { OV(37), 275 }, + { OV(39), 270 }, + { OV(42), 265 }, + { OV(46), 260 }, + { OV(49), 255 }, + { OV(53), 250 }, // 256.5 + { OV(57), 245 }, + { OV(62), 240 }, + { OV(67), 235 }, + { OV(73), 230 }, + { OV(79), 225 }, + { OV(86), 220 }, + { OV(94), 215 }, + { OV(103), 210 }, + { OV(112), 205 }, + { OV(123), 200 }, + { OV(135), 195 }, + { OV(148), 190 }, + { OV(162), 185 }, + { OV(178), 180 }, + { OV(195), 175 }, + { OV(215), 170 }, + { OV(235), 165 }, + { OV(258), 160 }, + { OV(283), 155 }, + { OV(310), 150 }, // 2040.6 + { OV(338), 145 }, + { OV(369), 140 }, + { OV(401), 135 }, + { OV(435), 130 }, + { OV(470), 125 }, + { OV(505), 120 }, + { OV(542), 115 }, + { OV(579), 110 }, + { OV(615), 105 }, + { OV(651), 100 }, + { OV(686), 95 }, + { OV(720), 90 }, + { OV(751), 85 }, + { OV(781), 80 }, + { OV(809), 75 }, + { OV(835), 70 }, + { OV(858), 65 }, + { OV(880), 60 }, + { OV(899), 55 }, + { OV(915), 50 }, + { OV(930), 45 }, + { OV(944), 40 }, + { OV(955), 35 }, + { OV(965), 30 }, // 78279.3 + { OV(974), 25 }, + { OV(981), 20 }, + { OV(988), 15 }, + { OV(993), 10 }, + { OV(998), 5 }, + { OV(1002), 0 }, +}; diff --git a/Marlin/src/module/thermistor/thermistors.h b/Marlin/src/module/thermistor/thermistors.h index 21fd10526d..65ae8af8c7 100644 --- a/Marlin/src/module/thermistor/thermistors.h +++ b/Marlin/src/module/thermistor/thermistors.h @@ -56,6 +56,9 @@ #if ANY_THERMISTOR_IS(501) // 100K Zonestar thermistor #include "thermistor_501.h" #endif +#if ANY_THERMISTOR_IS(512) // 100k thermistor in RPW-Ultra hotend, Pull-up = 4.7 kOhm, "unknown model" + #include "thermistor_512.h" +#endif #if ANY_THERMISTOR_IS(6) // beta25 = 4092 K, R25 = 100 kOhm, Pull-up = 8.2 kOhm, "EPCOS ?" #include "thermistor_6.h" #endif diff --git a/Marlin/src/module/tool_change.cpp b/Marlin/src/module/tool_change.cpp index 5c6d37ad97..264dd16700 100644 --- a/Marlin/src/module/tool_change.cpp +++ b/Marlin/src/module/tool_change.cpp @@ -81,6 +81,10 @@ #include "../lcd/ultralcd.h" #endif +#if ENABLED(ADVANCED_PAUSE_FEATURE) + #include "../feature/pause.h" +#endif + #if DO_SWITCH_EXTRUDER #if EXTRUDERS > 3 @@ -135,17 +139,17 @@ inline void fast_line_to_current(const AxisEnum fr_axis) { #if ENABLED(MAGNETIC_PARKING_EXTRUDER) - float parkingposx[2] , // M951 R L - parkinggrabdistance , // M951 I - parkingslowspeed, // M951 J - parkinghighspeed , // M951 H - parkingtraveldistance, // M951 D + float parkingposx[2], // M951 R L + parkinggrabdistance, // M951 I + parkingslowspeed, // M951 J + parkinghighspeed, // M951 H + parkingtraveldistance, // M951 D compensationmultiplier; - inline void magnetic_parking_extruder_tool_change(const uint8_t tmp_extruder) { + inline void magnetic_parking_extruder_tool_change(const uint8_t new_tool) { const float oldx = current_position[X_AXIS], - grabpos = mpe_settings.parking_xpos[tmp_extruder] + (tmp_extruder ? mpe_settings.grab_distance : -mpe_settings.grab_distance), + grabpos = mpe_settings.parking_xpos[new_tool] + (new_tool ? mpe_settings.grab_distance : -mpe_settings.grab_distance), offsetcompensation = #if HAS_HOTEND_OFFSET hotend_offset[X_AXIS][active_extruder] * mpe_settings.compensation_factor @@ -170,14 +174,14 @@ inline void fast_line_to_current(const AxisEnum fr_axis) { // STEP 1 - current_position[X_AXIS] = mpe_settings.parking_xpos[tmp_extruder] + offsetcompensation; + current_position[X_AXIS] = mpe_settings.parking_xpos[new_tool] + offsetcompensation; if (DEBUGGING(LEVELING)) { - DEBUG_ECHOPAIR("(1) Move extruder ", int(tmp_extruder)); + DEBUG_ECHOPAIR("(1) Move extruder ", int(new_tool)); DEBUG_POS(" to new extruder ParkPos", current_position); } - planner.buffer_line(current_position, mpe_settings.fast_feedrate, tmp_extruder); + planner.buffer_line(current_position, mpe_settings.fast_feedrate, new_tool); planner.synchronize(); // STEP 2 @@ -185,11 +189,11 @@ inline void fast_line_to_current(const AxisEnum fr_axis) { current_position[X_AXIS] = grabpos + offsetcompensation; if (DEBUGGING(LEVELING)) { - DEBUG_ECHOPAIR("(2) Couple extruder ", int(tmp_extruder)); + DEBUG_ECHOPAIR("(2) Couple extruder ", int(new_tool)); DEBUG_POS(" to new extruder GrabPos", current_position); } - planner.buffer_line(current_position, mpe_settings.slow_feedrate, tmp_extruder); + planner.buffer_line(current_position, mpe_settings.slow_feedrate, new_tool); planner.synchronize(); // Delay before moving tool, to allow magnetic coupling @@ -197,24 +201,24 @@ inline void fast_line_to_current(const AxisEnum fr_axis) { // STEP 3 - current_position[X_AXIS] = mpe_settings.parking_xpos[tmp_extruder] + offsetcompensation; + current_position[X_AXIS] = mpe_settings.parking_xpos[new_tool] + offsetcompensation; if (DEBUGGING(LEVELING)) { - DEBUG_ECHOPAIR("(3) Move extruder ", int(tmp_extruder)); + DEBUG_ECHOPAIR("(3) Move extruder ", int(new_tool)); DEBUG_POS(" back to new extruder ParkPos", current_position); } - planner.buffer_line(current_position, mpe_settings.slow_feedrate, tmp_extruder); + planner.buffer_line(current_position, mpe_settings.slow_feedrate, new_tool); planner.synchronize(); // STEP 4 current_position[X_AXIS] = mpe_settings.parking_xpos[active_extruder] + (active_extruder == 0 ? MPE_TRAVEL_DISTANCE : -MPE_TRAVEL_DISTANCE) + offsetcompensation; if (DEBUGGING(LEVELING)) { - DEBUG_ECHOPAIR("(4) Move extruder ", int(tmp_extruder)); + DEBUG_ECHOPAIR("(4) Move extruder ", int(new_tool)); DEBUG_POS(" close to old extruder ParkPos", current_position); } - planner.buffer_line(current_position, mpe_settings.fast_feedrate, tmp_extruder); + planner.buffer_line(current_position, mpe_settings.fast_feedrate, new_tool); planner.synchronize(); // STEP 5 @@ -222,11 +226,11 @@ inline void fast_line_to_current(const AxisEnum fr_axis) { current_position[X_AXIS] = mpe_settings.parking_xpos[active_extruder] + offsetcompensation; if (DEBUGGING(LEVELING)) { - DEBUG_ECHOPAIR("(5) Park extruder ", int(tmp_extruder)); + DEBUG_ECHOPAIR("(5) Park extruder ", int(new_tool)); DEBUG_POS(" at old extruder ParkPos", current_position); } - planner.buffer_line(current_position, mpe_settings.slow_feedrate, tmp_extruder); + planner.buffer_line(current_position, mpe_settings.slow_feedrate, new_tool); planner.synchronize(); // STEP 6 @@ -234,11 +238,11 @@ inline void fast_line_to_current(const AxisEnum fr_axis) { current_position[X_AXIS] = oldx; if (DEBUGGING(LEVELING)) { - DEBUG_ECHOPAIR("(6) Move extruder ", int(tmp_extruder)); + DEBUG_ECHOPAIR("(6) Move extruder ", int(new_tool)); DEBUG_POS(" to starting position", current_position); } - planner.buffer_line(current_position, mpe_settings.fast_feedrate, tmp_extruder); + planner.buffer_line(current_position, mpe_settings.fast_feedrate, new_tool); planner.synchronize(); if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("Autopark done."); @@ -265,7 +269,7 @@ inline void fast_line_to_current(const AxisEnum fr_axis) { #endif } - inline void parking_extruder_tool_change(const uint8_t tmp_extruder, bool no_move) { + inline void parking_extruder_tool_change(const uint8_t new_tool, bool no_move) { if (!no_move) { constexpr float parkingposx[] = PARKING_EXTRUDER_PARKING_X; @@ -277,7 +281,7 @@ inline void fast_line_to_current(const AxisEnum fr_axis) { #endif const float midpos = (parkingposx[0] + parkingposx[1]) * 0.5 + x_offset, - grabpos = parkingposx[tmp_extruder] + (tmp_extruder ? PARKING_EXTRUDER_GRAB_DISTANCE : -(PARKING_EXTRUDER_GRAB_DISTANCE)) + x_offset; + grabpos = parkingposx[new_tool] + (new_tool ? PARKING_EXTRUDER_GRAB_DISTANCE : -(PARKING_EXTRUDER_GRAB_DISTANCE)) + x_offset; /** * 1. Move to park position of old extruder @@ -290,71 +294,70 @@ inline void fast_line_to_current(const AxisEnum fr_axis) { // STEP 1 - if (DEBUGGING(LEVELING)) DEBUG_POS("Start Autopark", current_position); + if (DEBUGGING(LEVELING)) DEBUG_POS("Start PE Tool-Change", current_position); current_position[X_AXIS] = parkingposx[active_extruder] + x_offset; - if (DEBUGGING(LEVELING)) { DEBUG_ECHOLNPAIR("(1) Park extruder ", int(active_extruder)); DEBUG_POS("Moving ParkPos", current_position); } - fast_line_to_current(X_AXIS); - planner.synchronize(); // STEP 2 - if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("(2) Disengage magnet "); - + planner.synchronize(); + if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("(2) Disengage magnet"); pe_deactivate_solenoid(active_extruder); // STEP 3 - if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("(3) Move near new extruder"); - current_position[X_AXIS] += active_extruder ? -10 : 10; // move 10mm away from parked extruder - - if (DEBUGGING(LEVELING)) DEBUG_POS("Move away from parked extruder", current_position); - + if (DEBUGGING(LEVELING)) { + DEBUG_ECHOLNPGM("(3) Move near new extruder"); + DEBUG_POS("Move away from parked extruder", current_position); + } fast_line_to_current(X_AXIS); - planner.synchronize(); // STEP 4 + + planner.synchronize(); if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("(4) Engage magnetic field"); - #if ENABLED(PARKING_EXTRUDER_SOLENOIDS_INVERT) - pe_activate_solenoid(active_extruder); //just save power for inverted magnets + pe_activate_solenoid(active_extruder); // Just save power for inverted magnets #endif - - pe_activate_solenoid(tmp_extruder); + pe_activate_solenoid(new_tool); // STEP 5 - current_position[X_AXIS] = grabpos + (tmp_extruder ? -10 : 10); + current_position[X_AXIS] = grabpos + (new_tool ? -10 : 10); fast_line_to_current(X_AXIS); + current_position[X_AXIS] = grabpos; - if (DEBUGGING(LEVELING)) DEBUG_POS("(5) Unpark extruder", current_position); + if (DEBUGGING(LEVELING)) { + planner.synchronize(); + DEBUG_POS("(5) Unpark extruder", current_position); + } planner.buffer_line(current_position, planner.settings.max_feedrate_mm_s[X_AXIS] * 0.5, active_extruder); - planner.synchronize(); // STEP 6 current_position[X_AXIS] = midpos #if HAS_HOTEND_OFFSET - - hotend_offset[X_AXIS][tmp_extruder] + - hotend_offset[X_AXIS][new_tool] #endif ; - - if (DEBUGGING(LEVELING)) DEBUG_POS("(6) Move midway between hotends", current_position); - + if (DEBUGGING(LEVELING)) { + planner.synchronize(); + DEBUG_POS("(6) Move midway between hotends", current_position); + } fast_line_to_current(X_AXIS); - planner.synchronize(); + planner.synchronize(); // Always sync the final move - DEBUG_ECHOLNPGM("Autopark done."); + if (DEBUGGING(LEVELING)) DEBUG_POS("PE Tool-Change done.", current_position); } else { // nomove == true // Only engage magnetic field for new extruder - pe_activate_solenoid(tmp_extruder); + pe_activate_solenoid(new_tool); #if ENABLED(PARKING_EXTRUDER_SOLENOIDS_INVERT) pe_activate_solenoid(active_extruder); // Just save power for inverted magnets #endif @@ -365,14 +368,14 @@ inline void fast_line_to_current(const AxisEnum fr_axis) { #if ENABLED(SWITCHING_TOOLHEAD) - inline void switching_toolhead_tool_change(const uint8_t tmp_extruder, bool no_move/*=false*/) { + inline void switching_toolhead_tool_change(const uint8_t new_tool, bool no_move/*=false*/) { if (no_move) return; constexpr uint16_t angles[2] = SWITCHING_TOOLHEAD_SERVO_ANGLES; constexpr float toolheadposx[] = SWITCHING_TOOLHEAD_X_POS; const float placexpos = toolheadposx[active_extruder], - grabxpos = toolheadposx[tmp_extruder]; + grabxpos = toolheadposx[new_tool]; /** * 1. Move to switch position of current toolhead @@ -383,96 +386,94 @@ inline void fast_line_to_current(const AxisEnum fr_axis) { // 1. Move to switch position of current toolhead - if (DEBUGGING(LEVELING)) DEBUG_POS("Starting Toolhead change", current_position); + if (DEBUGGING(LEVELING)) DEBUG_POS("Start ST Tool-Change", current_position); current_position[X_AXIS] = placexpos; - if (DEBUGGING(LEVELING)) { DEBUG_ECHOLNPAIR("(1) Place old tool ", int(active_extruder)); DEBUG_POS("Move X SwitchPos", current_position); } - fast_line_to_current(X_AXIS); - planner.synchronize(); - - current_position[Y_AXIS] = SWITCHING_TOOLHEAD_Y_POS - SWITCHING_TOOLHEAD_Y_SECURITY; - - if (DEBUGGING(LEVELING)) DEBUG_POS("Move Y SwitchPos + Security", current_position); + current_position[Y_AXIS] = SWITCHING_TOOLHEAD_Y_POS - (SWITCHING_TOOLHEAD_Y_SECURITY); + if (DEBUGGING(LEVELING)) { + planner.synchronize(); + DEBUG_POS("Move Y SwitchPos + Security", current_position); + } fast_line_to_current(Y_AXIS); - planner.synchronize(); // 2. Unlock tool and drop it in the dock + planner.synchronize(); if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("(2) Unlock and Place Toolhead"); - MOVE_SERVO(SWITCHING_TOOLHEAD_SERVO_NR, angles[1]); safe_delay(500); current_position[Y_AXIS] = SWITCHING_TOOLHEAD_Y_POS; - if (DEBUGGING(LEVELING)) DEBUG_POS("Move Y SwitchPos", current_position); + planner.buffer_line(current_position, planner.settings.max_feedrate_mm_s[Y_AXIS] * 0.5f, active_extruder); - planner.buffer_line(current_position,(planner.settings.max_feedrate_mm_s[Y_AXIS] * 0.5), active_extruder); + // Wait for move to complete, then another 0.2s planner.synchronize(); safe_delay(200); + current_position[Y_AXIS] -= SWITCHING_TOOLHEAD_Y_CLEAR; - if (DEBUGGING(LEVELING)) DEBUG_POS("Move back Y clear", current_position); - fast_line_to_current(Y_AXIS); // move away from docked toolhead - planner.synchronize(); // 3. Move to the new toolhead - if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("(3) Move to new toolhead position"); - current_position[X_AXIS] = grabxpos; - - if (DEBUGGING(LEVELING)) DEBUG_POS("Move to new toolhead X", current_position); - + if (DEBUGGING(LEVELING)) { + planner.synchronize(); + DEBUG_ECHOLNPGM("(3) Move to new toolhead position"); + DEBUG_POS("Move to new toolhead X", current_position); + } fast_line_to_current(X_AXIS); - planner.synchronize(); - current_position[Y_AXIS] = SWITCHING_TOOLHEAD_Y_POS - SWITCHING_TOOLHEAD_Y_SECURITY; - - if (DEBUGGING(LEVELING)) DEBUG_POS("Move Y SwitchPos + Security", current_position); + current_position[Y_AXIS] = SWITCHING_TOOLHEAD_Y_POS - (SWITCHING_TOOLHEAD_Y_SECURITY); + if (DEBUGGING(LEVELING)) { + planner.synchronize(); + DEBUG_POS("Move Y SwitchPos + Security", current_position); + } fast_line_to_current(Y_AXIS); - planner.synchronize(); // 4. Grab and lock the new toolhead - if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("(4) Grab and lock new toolhead "); - current_position[Y_AXIS] = SWITCHING_TOOLHEAD_Y_POS; - - if (DEBUGGING(LEVELING)) DEBUG_POS("Move Y SwitchPos", current_position); - + if (DEBUGGING(LEVELING)) { + planner.synchronize(); + DEBUG_ECHOLNPGM("(4) Grab and lock new toolhead"); + DEBUG_POS("Move Y SwitchPos", current_position); + } planner.buffer_line(current_position, planner.settings.max_feedrate_mm_s[Y_AXIS] * 0.5, active_extruder); - planner.synchronize(); + // Wait for move to finish, pause 0.2s, move servo, pause 0.5s + planner.synchronize(); safe_delay(200); MOVE_SERVO(SWITCHING_TOOLHEAD_SERVO_NR, angles[0]); safe_delay(500); current_position[Y_AXIS] -= SWITCHING_TOOLHEAD_Y_CLEAR; - if (DEBUGGING(LEVELING)) DEBUG_POS("Move back Y clear", current_position); + fast_line_to_current(Y_AXIS); // Move away from docked toolhead + planner.synchronize(); // Always sync the final move - fast_line_to_current(Y_AXIS); // move away from docked toolhead - planner.synchronize(); - - if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("Toolhead change done."); + if (DEBUGGING(LEVELING)) DEBUG_POS("ST Tool-Change done.", current_position); } #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) - inline void magnetic_switching_toolhead_tool_change(const uint8_t tmp_extruder, bool no_move/*=false*/) { + inline void magnetic_switching_toolhead_tool_change(const uint8_t new_tool, bool no_move/*=false*/) { if (no_move) return; - constexpr float toolheadposx[] = SWITCHING_TOOLHEAD_X_POS; + constexpr float toolheadposx[] = SWITCHING_TOOLHEAD_X_POS, + toolheadclearx[] = SWITCHING_TOOLHEAD_X_SECURITY; + const float placexpos = toolheadposx[active_extruder], - grabxpos = toolheadposx[tmp_extruder]; + placexclear = toolheadclearx[active_extruder], + grabxpos = toolheadposx[new_tool], + grabxclear = toolheadclearx[new_tool]; /** * 1. Move to switch position of current toolhead @@ -481,103 +482,111 @@ inline void fast_line_to_current(const AxisEnum fr_axis) { * 4. Grab the new toolhead and move to security position */ - if (DEBUGGING(LEVELING)) DEBUG_POS("Starting Toolhead change", current_position); + if (DEBUGGING(LEVELING)) DEBUG_POS("Start MST Tool-Change", current_position); // 1. Move to switch position current toolhead current_position[Y_AXIS] = SWITCHING_TOOLHEAD_Y_POS + SWITCHING_TOOLHEAD_Y_CLEAR; - if (DEBUGGING(LEVELING)) { SERIAL_ECHOLNPAIR("(1) Place old tool ", int(active_extruder)); DEBUG_POS("Move Y SwitchPos + Security", current_position); } - planner.buffer_line(current_position, planner.settings.max_feedrate_mm_s[Y_AXIS], active_extruder); - planner.synchronize(); - - current_position[X_AXIS] = placexpos + SWITCHING_TOOLHEAD_X_SECURITY; - - if (DEBUGGING(LEVELING)) DEBUG_POS("Move X SwitchPos + Security", current_position); + current_position[X_AXIS] = placexclear; + if (DEBUGGING(LEVELING)) { + planner.synchronize(); + DEBUG_POS("Move X SwitchPos + Security", current_position); + } planner.buffer_line(current_position, planner.settings.max_feedrate_mm_s[X_AXIS], active_extruder); - planner.synchronize(); current_position[Y_AXIS] = SWITCHING_TOOLHEAD_Y_POS; - - if (DEBUGGING(LEVELING)) DEBUG_POS("Move Y SwitchPos", current_position); - + if (DEBUGGING(LEVELING)) { + planner.synchronize(); + DEBUG_POS("Move Y SwitchPos", current_position); + } planner.buffer_line(current_position, planner.settings.max_feedrate_mm_s[Y_AXIS], active_extruder); - planner.synchronize(); current_position[X_AXIS] = placexpos; - - if (DEBUGGING(LEVELING)) DEBUG_POS("Move X SwitchPos", current_position); - + if (DEBUGGING(LEVELING)) { + planner.synchronize(); + DEBUG_POS("Move X SwitchPos", current_position); + } planner.buffer_line(current_position, (planner.settings.max_feedrate_mm_s[X_AXIS] * 0.25), active_extruder); - planner.synchronize(); // 2. Release and place toolhead in the dock - if (DEBUGGING(LEVELING)) SERIAL_ECHOLNPGM("(2) Release and Place Toolhead"); + if (DEBUGGING(LEVELING)) { + planner.synchronize(); + DEBUG_ECHOLNPGM("(2) Release and Place Toolhead"); + } current_position[Y_AXIS] = SWITCHING_TOOLHEAD_Y_POS + SWITCHING_TOOLHEAD_Y_RELEASE; - if (DEBUGGING(LEVELING)) DEBUG_POS("Move Y SwitchPos + Release", current_position); - planner.buffer_line(current_position, (planner.settings.max_feedrate_mm_s[Y_AXIS] * 0.1), active_extruder); - planner.synchronize(); current_position[Y_AXIS] = SWITCHING_TOOLHEAD_Y_POS + SWITCHING_TOOLHEAD_Y_SECURITY; - - if (DEBUGGING(LEVELING)) DEBUG_POS("Move Y SwitchPos + Security", current_position); - + if (DEBUGGING(LEVELING)) { + planner.synchronize(); + DEBUG_POS("Move Y SwitchPos + Security", current_position); + } planner.buffer_line(current_position, (planner.settings.max_feedrate_mm_s[Y_AXIS]), active_extruder); - planner.synchronize(); // 3. Move to new toolhead position - if (DEBUGGING(LEVELING)) SERIAL_ECHOLNPGM("(3) Move to new toolhead position"); + if (DEBUGGING(LEVELING)) { + planner.synchronize(); + DEBUG_ECHOLNPGM("(3) Move to new toolhead position"); + } current_position[X_AXIS] = grabxpos; - if (DEBUGGING(LEVELING)) DEBUG_POS("Move to new toolhead X", current_position); - planner.buffer_line(current_position, planner.settings.max_feedrate_mm_s[X_AXIS], active_extruder); - planner.synchronize(); // 4. Grab the new toolhead and move to security position - if (DEBUGGING(LEVELING)) SERIAL_ECHOLNPGM("(4) Grab new toolhead and move to security position"); + if (DEBUGGING(LEVELING)) { + planner.synchronize(); + DEBUG_ECHOLNPGM("(4) Grab new toolhead, move to security position"); + } current_position[Y_AXIS] = SWITCHING_TOOLHEAD_Y_POS + SWITCHING_TOOLHEAD_Y_RELEASE; - if (DEBUGGING(LEVELING)) DEBUG_POS("Move Y SwitchPos + Release", current_position); - planner.buffer_line(current_position, (planner.settings.max_feedrate_mm_s[Y_AXIS]), active_extruder); - planner.synchronize(); current_position[Y_AXIS] = SWITCHING_TOOLHEAD_Y_POS; - - if (DEBUGGING(LEVELING)) DEBUG_POS("Move Y SwitchPos", current_position); - + if (DEBUGGING(LEVELING)) { + planner.synchronize(); + DEBUG_POS("Move Y SwitchPos", current_position); + } planner.buffer_line(current_position, planner.settings.max_feedrate_mm_s[Y_AXIS] * 0.2, active_extruder); - planner.synchronize(); - safe_delay(100); - current_position[X_AXIS] = grabxpos + SWITCHING_TOOLHEAD_X_SECURITY; + #if ENABLED(PRIME_BEFORE_REMOVE) && (SWITCHING_TOOLHEAD_PRIME_MM || SWITCHING_TOOLHEAD_RETRACT_MM) + #if SWITCHING_TOOLHEAD_PRIME_MM + current_position[E_AXIS] += SWITCHING_TOOLHEAD_PRIME_MM; + planner.buffer_line(current_position, MMM_TO_MMS(SWITCHING_TOOLHEAD_PRIME_FEEDRATE), new_tool); + #endif + #if SWITCHING_TOOLHEAD_RETRACT_MM + current_position[E_AXIS] -= SWITCHING_TOOLHEAD_RETRACT_MM; + planner.buffer_line(current_position, MMM_TO_MMS(SWITCHING_TOOLHEAD_RETRACT_FEEDRATE), new_tool); + #endif + #else + planner.synchronize(); + safe_delay(100); // Give switch time to settle + #endif + current_position[X_AXIS] = grabxclear; if (DEBUGGING(LEVELING)) DEBUG_POS("Move to new toolhead X + Security", current_position); - planner.buffer_line(current_position, planner.settings.max_feedrate_mm_s[X_AXIS] * 0.1, active_extruder); planner.synchronize(); - safe_delay(100); + safe_delay(100); // Give switch time to settle current_position[Y_AXIS] += SWITCHING_TOOLHEAD_Y_CLEAR; - if (DEBUGGING(LEVELING)) DEBUG_POS("Move back Y clear", current_position); - planner.buffer_line(current_position, planner.settings.max_feedrate_mm_s[Y_AXIS], active_extruder); // move away from docked toolhead - planner.synchronize(); + planner.synchronize(); // Always sync last tool-change move + + if (DEBUGGING(LEVELING)) DEBUG_POS("MST Tool-Change done.", current_position); } #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) @@ -586,12 +595,12 @@ inline void fast_line_to_current(const AxisEnum fr_axis) { inline void est_deactivate_solenoid() { OUT_WRITE(SOL0_PIN, LOW); } void est_init() { est_activate_solenoid(); } - inline void electromagnetic_switching_toolhead(const uint8_t tmp_extruder, bool no_move) { + inline void em_switching_toolhead_tool_change(const uint8_t new_tool, bool no_move) { if (no_move) return; constexpr float toolheadposx[] = SWITCHING_TOOLHEAD_X_POS; const float placexpos = toolheadposx[active_extruder], - grabxpos = toolheadposx[tmp_extruder]; + grabxpos = toolheadposx[new_tool]; /** * 1. Raise Z-Axis to give enough clearance @@ -605,110 +614,83 @@ inline void fast_line_to_current(const AxisEnum fr_axis) { * 9. Apply Z hotend offset to current position */ - #if ENABLED(DEBUG_LEVELING_FEATURE) - if (DEBUGGING(LEVELING)) DEBUG_POS("Starting Autopark", current_position); - #endif + if (DEBUGGING(LEVELING)) DEBUG_POS("Start EMST Tool-Change", current_position); // 1. Raise Z-Axis to give enough clearance current_position[Z_AXIS] += SWITCHING_TOOLHEAD_Z_HOP; - #if ENABLED(DEBUG_LEVELING_FEATURE) - if (DEBUGGING(LEVELING)) DEBUG_POS("(1) Raise Z-Axis ", current_position); - #endif + if (DEBUGGING(LEVELING)) DEBUG_POS("(1) Raise Z-Axis ", current_position); planner.buffer_line(current_position, planner.settings.max_feedrate_mm_s[Z_AXIS], active_extruder); // 2. Move to position near active extruder parking - #if ENABLED(DEBUG_LEVELING_FEATURE) - if (DEBUGGING(LEVELING)) { - planner.synchronize(); - SERIAL_ECHOLNPAIR("(2) Move near active extruder parking", active_extruder); - DEBUG_POS("Moving ParkPos", current_position); - } - #endif + if (DEBUGGING(LEVELING)) { + planner.synchronize(); + SERIAL_ECHOLNPAIR("(2) Move near active extruder parking", active_extruder); + DEBUG_POS("Moving ParkPos", current_position); + } current_position[X_AXIS] = placexpos + hotend_offset[X_AXIS][active_extruder]; current_position[Y_AXIS] = SWITCHING_TOOLHEAD_Y_POS + SWITCHING_TOOLHEAD_Y_CLEAR + hotend_offset[Y_AXIS][active_extruder]; planner.buffer_line(current_position, planner.settings.max_feedrate_mm_s[X_AXIS], active_extruder); // 3. Move gently to park position of active extruder - #if ENABLED(DEBUG_LEVELING_FEATURE) - if (DEBUGGING(LEVELING)) { - planner.synchronize(); - SERIAL_ECHOLNPAIR("(3) Move gently to park position of active extruder", active_extruder); - DEBUG_POS("Moving ParkPos", current_position); - } - #endif + if (DEBUGGING(LEVELING)) { + planner.synchronize(); + SERIAL_ECHOLNPAIR("(3) Move gently to park position of active extruder", active_extruder); + DEBUG_POS("Moving ParkPos", current_position); + } current_position[Y_AXIS] -= SWITCHING_TOOLHEAD_Y_CLEAR; planner.buffer_line(current_position, planner.settings.max_feedrate_mm_s[Y_AXIS] * 0.5, active_extruder); // 4. Disengage magnetic field, wait for delay - #if ENABLED(DEBUG_LEVELING_FEATURE) - if (DEBUGGING(LEVELING)) SERIAL_ECHOLNPGM("(4) Disengage magnet"); - #endif - planner.synchronize(); + if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("(4) Disengage magnet"); est_deactivate_solenoid(); // 5. Leave extruder and move to position near new extruder parking - #if ENABLED(DEBUG_LEVELING_FEATURE) - if (DEBUGGING(LEVELING)) { - SERIAL_ECHOLNPGM("(5) Move near new extruder parking"); - DEBUG_POS("Moving ParkPos", current_position); - } - #endif + if (DEBUGGING(LEVELING)) { + DEBUG_ECHOLNPGM("(5) Move near new extruder parking"); + DEBUG_POS("Moving ParkPos", current_position); + } current_position[Y_AXIS] += SWITCHING_TOOLHEAD_Y_CLEAR; planner.buffer_line(current_position, planner.settings.max_feedrate_mm_s[Y_AXIS] * 0.5f, active_extruder); - current_position[X_AXIS] = grabxpos + hotend_offset[X_AXIS][active_extruder]; current_position[Y_AXIS] = SWITCHING_TOOLHEAD_Y_POS + SWITCHING_TOOLHEAD_Y_CLEAR + hotend_offset[Y_AXIS][active_extruder]; planner.buffer_line(current_position, planner.settings.max_feedrate_mm_s[X_AXIS], active_extruder); // 6. Move gently to park position of new extruder - #if ENABLED(DEBUG_LEVELING_FEATURE) - if (DEBUGGING(LEVELING)) { - planner.synchronize(); - SERIAL_ECHOLNPGM("(6) Move near new extruder"); - } - #endif - current_position[Y_AXIS] -= SWITCHING_TOOLHEAD_Y_CLEAR; + if (DEBUGGING(LEVELING)) { + planner.synchronize(); + DEBUG_ECHOLNPGM("(6) Move near new extruder"); + } planner.buffer_line(current_position, planner.settings.max_feedrate_mm_s[Y_AXIS] * 0.5f, active_extruder); // 7. Engage magnetic field for new extruder parking - #if ENABLED(DEBUG_LEVELING_FEATURE) - if (DEBUGGING(LEVELING)) SERIAL_ECHOLNPGM("(7) Engage magnetic field"); - #endif - planner.synchronize(); + if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("(7) Engage magnetic field"); est_activate_solenoid(); // 8. Unpark extruder - #if ENABLED(DEBUG_LEVELING_FEATURE) - if (DEBUGGING(LEVELING)) SERIAL_ECHOLNPGM("(8) Unpark extruder"); - #endif - current_position[Y_AXIS] += SWITCHING_TOOLHEAD_Y_CLEAR; - + if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPGM("(8) Unpark extruder"); planner.buffer_line(current_position, planner.settings.max_feedrate_mm_s[X_AXIS] * 0.5f, active_extruder); + planner.synchronize(); // Always sync the final move // 9. Apply Z hotend offset to current position - current_position[Z_AXIS] += hotend_offset[Z_AXIS][active_extruder] - hotend_offset[Z_AXIS][tmp_extruder]; + if (DEBUGGING(LEVELING)) DEBUG_POS("(9) Applying Z-offset", current_position); + current_position[Z_AXIS] += hotend_offset[Z_AXIS][active_extruder] - hotend_offset[Z_AXIS][new_tool]; - #if ENABLED(DEBUG_LEVELING_FEATURE) - if (DEBUGGING(LEVELING)) { - planner.synchronize(); - DEBUG_POS("(9) Applying Z-offset", current_position); - } - #endif + if (DEBUGGING(LEVELING)) DEBUG_POS("EMST Tool-Change done.", current_position); } #endif // ELECTROMAGNETIC_SWITCHING_TOOLHEAD @@ -721,7 +703,7 @@ inline void invalid_extruder_error(const uint8_t e) { #if ENABLED(DUAL_X_CARRIAGE) - inline void dualx_tool_change(const uint8_t tmp_extruder, bool &no_move) { + inline void dualx_tool_change(const uint8_t new_tool, bool &no_move) { if (DEBUGGING(LEVELING)) { DEBUG_ECHOPGM("Dual X Carriage Mode "); switch (dual_x_carriage_mode) { @@ -746,7 +728,7 @@ inline void invalid_extruder_error(const uint8_t e) { } // Activate the new extruder ahead of calling set_axis_is_at_home! - active_extruder = tmp_extruder; + active_extruder = new_tool; // This function resets the max/min values - the current position may be overwritten below. set_axis_is_at_home(X_AXIS); @@ -782,35 +764,35 @@ inline void invalid_extruder_error(const uint8_t e) { * Perform a tool-change, which may result in moving the * previous tool out of the way and the new tool into place. */ -void tool_change(const uint8_t tmp_extruder, bool no_move/*=false*/) { +void tool_change(const uint8_t new_tool, bool no_move/*=false*/) { #if ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) - if (tmp_extruder == active_extruder) return; + if (new_tool == active_extruder) return; #endif #if ENABLED(MIXING_EXTRUDER) UNUSED(no_move); - if (tmp_extruder >= MIXING_VIRTUAL_TOOLS) - return invalid_extruder_error(tmp_extruder); + if (new_tool >= MIXING_VIRTUAL_TOOLS) + return invalid_extruder_error(new_tool); #if MIXING_VIRTUAL_TOOLS > 1 // T0-Tnnn: Switch virtual tool by changing the index to the mix - mixer.T(tmp_extruder); + mixer.T(new_tool); #endif #elif ENABLED(PRUSA_MMU2) UNUSED(no_move); - mmu2.tool_change(tmp_extruder); + mmu2.tool_change(new_tool); #elif EXTRUDERS < 2 UNUSED(no_move); - if (tmp_extruder) invalid_extruder_error(tmp_extruder); + if (new_tool) invalid_extruder_error(new_tool); return; #else // EXTRUDERS > 1 @@ -818,18 +800,12 @@ void tool_change(const uint8_t tmp_extruder, bool no_move/*=false*/) { planner.synchronize(); #if ENABLED(DUAL_X_CARRIAGE) // Only T0 allowed if the Printer is in DXC_DUPLICATION_MODE or DXC_MIRRORED_MODE - if (tmp_extruder != 0 && dxc_is_duplicating()) - return invalid_extruder_error(tmp_extruder); + if (new_tool != 0 && dxc_is_duplicating()) + return invalid_extruder_error(new_tool); #endif - #if HAS_LEVELING - // Set current position to the physical position - const bool leveling_was_active = planner.leveling_active; - set_bed_leveling_enabled(false); - #endif - - if (tmp_extruder >= EXTRUDERS) - return invalid_extruder_error(tmp_extruder); + if (new_tool >= EXTRUDERS) + return invalid_extruder_error(new_tool); if (!no_move && !all_axes_homed()) { no_move = true; @@ -846,12 +822,13 @@ void tool_change(const uint8_t tmp_extruder, bool no_move/*=false*/) { constexpr bool idex_full_control = false; #endif + const uint8_t old_tool = active_extruder; const bool can_move_away = !no_move && !idex_full_control; #if ENABLED(TOOLCHANGE_FILAMENT_SWAP) const bool should_swap = can_move_away && toolchange_settings.swap_length; #if ENABLED(PREVENT_COLD_EXTRUSION) - const bool too_cold = !DEBUGGING(DRYRUN) && (thermalManager.targetTooColdToExtrude(active_extruder) || thermalManager.targetTooColdToExtrude(tmp_extruder)); + const bool too_cold = !DEBUGGING(DRYRUN) && (thermalManager.targetTooColdToExtrude(old_tool) || thermalManager.targetTooColdToExtrude(new_tool)); #else constexpr bool too_cold = false; #endif @@ -859,7 +836,7 @@ void tool_change(const uint8_t tmp_extruder, bool no_move/*=false*/) { if (too_cold) { SERIAL_ECHO_MSG(MSG_ERR_HOTEND_TOO_COLD); #if ENABLED(SINGLENOZZLE) - active_extruder = tmp_extruder; + active_extruder = new_tool; return; #endif } @@ -867,25 +844,30 @@ void tool_change(const uint8_t tmp_extruder, bool no_move/*=false*/) { #if ENABLED(ADVANCED_PAUSE_FEATURE) do_pause_e_move(-toolchange_settings.swap_length, MMM_TO_MMS(toolchange_settings.retract_speed)); #else - current_position[E_AXIS] -= toolchange_settings.swap_length / planner.e_factor[active_extruder]; - planner.buffer_line(current_position, MMM_TO_MMS(toolchange_settings.retract_speed), active_extruder); + current_position[E_AXIS] -= toolchange_settings.swap_length / planner.e_factor[old_tool]; + planner.buffer_line(current_position, MMM_TO_MMS(toolchange_settings.retract_speed), old_tool); planner.synchronize(); #endif } } #endif // TOOLCHANGE_FILAMENT_SWAP - if (tmp_extruder != active_extruder) { + #if HAS_LEVELING + // Set current position to the physical position + TEMPORARY_BED_LEVELING_STATE(false); + #endif + + if (new_tool != old_tool) { #if SWITCHING_NOZZLE_TWO_SERVOS - raise_nozzle(active_extruder); + raise_nozzle(old_tool); #endif REMEMBER(fr, feedrate_mm_s, XY_PROBE_FEEDRATE_MM_S); #if HAS_SOFTWARE_ENDSTOPS #if HAS_HOTEND_OFFSET - #define _EXT_ARGS , active_extruder, tmp_extruder + #define _EXT_ARGS , old_tool, new_tool #else #define _EXT_ARGS #endif @@ -910,7 +892,7 @@ void tool_change(const uint8_t tmp_extruder, bool no_move/*=false*/) { current_position[X_AXIS] = toolchange_settings.change_point.x; current_position[Y_AXIS] = toolchange_settings.change_point.y; #endif - planner.buffer_line(current_position, feedrate_mm_s, active_extruder); + planner.buffer_line(current_position, feedrate_mm_s, old_tool); planner.synchronize(); } #endif @@ -919,35 +901,35 @@ void tool_change(const uint8_t tmp_extruder, bool no_move/*=false*/) { #if ENABLED(DUAL_X_CARRIAGE) constexpr float xdiff = 0; #else - const float xdiff = hotend_offset[X_AXIS][tmp_extruder] - hotend_offset[X_AXIS][active_extruder]; + const float xdiff = hotend_offset[X_AXIS][new_tool] - hotend_offset[X_AXIS][old_tool]; #endif - const float ydiff = hotend_offset[Y_AXIS][tmp_extruder] - hotend_offset[Y_AXIS][active_extruder], - zdiff = hotend_offset[Z_AXIS][tmp_extruder] - hotend_offset[Z_AXIS][active_extruder]; + const float ydiff = hotend_offset[Y_AXIS][new_tool] - hotend_offset[Y_AXIS][old_tool], + zdiff = hotend_offset[Z_AXIS][new_tool] - hotend_offset[Z_AXIS][old_tool]; #else constexpr float xdiff = 0, ydiff = 0, zdiff = 0; #endif #if ENABLED(DUAL_X_CARRIAGE) - dualx_tool_change(tmp_extruder, no_move); + dualx_tool_change(new_tool, no_move); #elif ENABLED(PARKING_EXTRUDER) // Dual Parking extruder - parking_extruder_tool_change(tmp_extruder, no_move); + parking_extruder_tool_change(new_tool, no_move); #elif ENABLED(MAGNETIC_PARKING_EXTRUDER) // Magnetic Parking extruder - magnetic_parking_extruder_tool_change(tmp_extruder); + magnetic_parking_extruder_tool_change(new_tool); #elif ENABLED(SWITCHING_TOOLHEAD) // Switching Toolhead - switching_toolhead_tool_change(tmp_extruder, no_move); + switching_toolhead_tool_change(new_tool, no_move); #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) // Magnetic Switching Toolhead - magnetic_switching_toolhead_tool_change(tmp_extruder, no_move); + magnetic_switching_toolhead_tool_change(new_tool, no_move); #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) // Magnetic Switching ToolChanger - electromagnetic_switching_toolhead(tmp_extruder, no_move); + em_switching_toolhead_tool_change(new_tool, no_move); #elif ENABLED(SWITCHING_NOZZLE) && !SWITCHING_NOZZLE_TWO_SERVOS // Switching Nozzle (single servo) // Raise by a configured distance to avoid workpiece, except with // SWITCHING_NOZZLE_TWO_SERVOS, as both nozzles will lift instead. - current_position[Z_AXIS] += MAX(-zdiff, 0.0) + toolchange_settings.z_raise; + current_position[Z_AXIS] += _MAX(-zdiff, 0.0) + toolchange_settings.z_raise; #if HAS_SOFTWARE_ENDSTOPS NOMORE(current_position[Z_AXIS], soft_endstop[Z_AXIS].max); #endif if (!no_move) fast_line_to_current(Z_AXIS); - move_nozzle_servo(tmp_extruder); + move_nozzle_servo(new_tool); #endif if (DEBUGGING(LEVELING)) DEBUG_ECHOLNPAIR("Offset Tool XY by { ", xdiff, ", ", ydiff, ", ", zdiff, " }"); @@ -958,7 +940,7 @@ void tool_change(const uint8_t tmp_extruder, bool no_move/*=false*/) { current_position[Z_AXIS] += zdiff; // Set the new active extruder if not already done in tool specific function above - active_extruder = tmp_extruder; + active_extruder = new_tool; // Tell the planner the new "current position" sync_plan_position(); @@ -975,34 +957,33 @@ void tool_change(const uint8_t tmp_extruder, bool no_move/*=false*/) { #if ENABLED(SINGLENOZZLE) #if FAN_COUNT > 0 - singlenozzle_fan_speed[active_extruder] = thermalManager.fan_speed[0]; - thermalManager.fan_speed[0] = singlenozzle_fan_speed[tmp_extruder]; + singlenozzle_fan_speed[old_tool] = thermalManager.fan_speed[0]; + thermalManager.fan_speed[0] = singlenozzle_fan_speed[new_tool]; #endif - singlenozzle_temp[active_extruder] = thermalManager.temp_hotend[0].target; - if (singlenozzle_temp[tmp_extruder] && singlenozzle_temp[tmp_extruder] != singlenozzle_temp[active_extruder]) { - thermalManager.setTargetHotend(singlenozzle_temp[tmp_extruder], 0); - #if EITHER(ULTRA_LCD, EXTENSIBLE_UI) + singlenozzle_temp[old_tool] = thermalManager.temp_hotend[0].target; + if (singlenozzle_temp[new_tool] && singlenozzle_temp[new_tool] != singlenozzle_temp[old_tool]) { + thermalManager.setTargetHotend(singlenozzle_temp[new_tool], 0); + #if HAS_DISPLAY thermalManager.set_heating_message(0); #endif (void)thermalManager.wait_for_hotend(0, false); // Wait for heating or cooling } - active_extruder = tmp_extruder; #endif #if ENABLED(TOOLCHANGE_FILAMENT_SWAP) if (should_swap && !too_cold) { #if ENABLED(ADVANCED_PAUSE_FEATURE) - do_pause_e_move(toolchange_settings.swap_length + TOOLCHANGE_FIL_EXTRA_PRIME, MMM_TO_MMS(toolchange_settings.prime_speed)); + do_pause_e_move(toolchange_settings.swap_length, MMM_TO_MMS(toolchange_settings.prime_speed)); + do_pause_e_move(toolchange_settings.extra_prime, ADVANCED_PAUSE_PURGE_FEEDRATE); #else - current_position[E_AXIS] += (toolchange_settings.swap_length + TOOLCHANGE_FIL_EXTRA_PRIME) / planner.e_factor[tmp_extruder]; - planner.buffer_line(current_position, MMM_TO_MMS(toolchange_settings.prime_speed), tmp_extruder); + current_position[E_AXIS] += toolchange_settings.swap_length / planner.e_factor[new_tool]; + planner.buffer_line(current_position, MMM_TO_MMS(toolchange_settings.prime_speed), new_tool); + current_position[E_AXIS] += toolchange_settings.extra_prime / planner.e_factor[new_tool]; + planner.buffer_line(current_position, MMM_TO_MMS(toolchange_settings.prime_speed * 0.2f), new_tool); #endif planner.synchronize(); - - #if TOOLCHANGE_FIL_EXTRA_PRIME - planner.set_e_position_mm((destination[E_AXIS] = current_position[E_AXIS] = current_position[E_AXIS] - (TOOLCHANGE_FIL_EXTRA_PRIME))); - #endif + planner.set_e_position_mm((destination[E_AXIS] = current_position[E_AXIS] = current_position[E_AXIS] - (TOOLCHANGE_FIL_EXTRA_PRIME))); } #endif @@ -1011,7 +992,7 @@ void tool_change(const uint8_t tmp_extruder, bool no_move/*=false*/) { // If the original position is within tool store area, go to X origin at once if (destination[Y_AXIS] < SWITCHING_TOOLHEAD_Y_POS + SWITCHING_TOOLHEAD_Y_CLEAR) { current_position[X_AXIS] = 0; - planner.buffer_line(current_position, planner.settings.max_feedrate_mm_s[X_AXIS], active_extruder); + planner.buffer_line(current_position, planner.settings.max_feedrate_mm_s[X_AXIS], new_tool); planner.synchronize(); } #else @@ -1044,14 +1025,14 @@ void tool_change(const uint8_t tmp_extruder, bool no_move/*=false*/) { #endif #if ENABLED(PRUSA_MMU2) - mmu2.tool_change(tmp_extruder); + mmu2.tool_change(new_tool); #endif #if SWITCHING_NOZZLE_TWO_SERVOS - lower_nozzle(active_extruder); + lower_nozzle(new_tool); #endif - } // (tmp_extruder != active_extruder) + } // (new_tool != old_tool) planner.synchronize(); @@ -1061,8 +1042,8 @@ void tool_change(const uint8_t tmp_extruder, bool no_move/*=false*/) { #endif #if ENABLED(MK2_MULTIPLEXER) - if (tmp_extruder >= E_STEPPERS) return invalid_extruder_error(tmp_extruder); - select_multiplexed_stepper(tmp_extruder); + if (new_tool >= E_STEPPERS) return invalid_extruder_error(new_tool); + select_multiplexed_stepper(new_tool); #endif #if DO_SWITCH_EXTRUDER @@ -1074,11 +1055,6 @@ void tool_change(const uint8_t tmp_extruder, bool no_move/*=false*/) { fanmux_switch(active_extruder); #endif - #if HAS_LEVELING - // Restore leveling to re-establish the logical position - set_bed_leveling_enabled(leveling_was_active); - #endif - SERIAL_ECHO_START(); SERIAL_ECHOLNPAIR(MSG_ACTIVE_EXTRUDER, int(active_extruder)); diff --git a/Marlin/src/module/tool_change.h b/Marlin/src/module/tool_change.h index 87be78b3a7..754c720096 100644 --- a/Marlin/src/module/tool_change.h +++ b/Marlin/src/module/tool_change.h @@ -27,7 +27,7 @@ typedef struct { #if ENABLED(TOOLCHANGE_FILAMENT_SWAP) - float swap_length; + float swap_length, extra_prime; int16_t prime_speed, retract_speed; #endif #if ENABLED(TOOLCHANGE_PARK) diff --git a/Marlin/src/pins/pins_ESP32.h b/Marlin/src/pins/esp32/pins_ESP32.h similarity index 100% rename from Marlin/src/pins/pins_ESP32.h rename to Marlin/src/pins/esp32/pins_ESP32.h diff --git a/Marlin/src/pins/pins_RAMPS_LINUX.h b/Marlin/src/pins/linux/pins_RAMPS_LINUX.h similarity index 83% rename from Marlin/src/pins/pins_RAMPS_LINUX.h rename to Marlin/src/pins/linux/pins_RAMPS_LINUX.h index 614890dda1..a726b38428 100644 --- a/Marlin/src/pins/pins_RAMPS_LINUX.h +++ b/Marlin/src/pins/linux/pins_RAMPS_LINUX.h @@ -49,6 +49,8 @@ #define BOARD_NAME "RAMPS 1.4" #endif +#define E2END 0xFFF // 4KB + #define IS_RAMPS_EFB // @@ -131,15 +133,15 @@ // SPI for Max6675 or Max31855 Thermocouple #if DISABLED(SDSUPPORT) - #define MAX6675_SS_PIN 66 // Do not use pin 53 if there is even the remote possibility of using Display/SD card + #define MAX6675_SS_PIN 66 // Don't use 53 if there is even the remote possibility of using Display/SD card #else - #define MAX6675_SS_PIN 66 // Do not use pin 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present + #define MAX6675_SS_PIN 66 // Don't use 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present #endif // // Augmentation for auto-assigning RAMPS plugs // -#if DISABLED(IS_RAMPS_EEB, IS_RAMPS_EEF, IS_RAMPS_EFB, IS_RAMPS_EFF, IS_RAMPS_SF) && !PIN_EXISTS(MOSFET_D) +#if NONE(IS_RAMPS_EEB, IS_RAMPS_EEF, IS_RAMPS_EFB, IS_RAMPS_EFF, IS_RAMPS_SF) && !PIN_EXISTS(MOSFET_D) #if HOTENDS > 1 #if TEMP_SENSOR_BED #define IS_RAMPS_EEB @@ -219,10 +221,10 @@ #endif #if ENABLED(CASE_LIGHT_ENABLE) && !defined(CASE_LIGHT_PIN) && !defined(SPINDLE_LASER_ENA_PIN) - #if NUM_SERVOS <= 1 // try to use servo connector first - #define CASE_LIGHT_PIN 6 // MUST BE HARDWARE PWM - #elif !(BOTH(ULTRA_LCD, NEWPANEL) && ANY(PANEL_ONE, VIKI2, miniVIKI, MINIPANEL, REPRAPWORLD_KEYPAD)) // try to use AUX 2 - #define CASE_LIGHT_PIN 44 // MUST BE HARDWARE PWM + #if NUM_SERVOS <= 1 // Prefer the servo connector + #define CASE_LIGHT_PIN 6 // Hardware PWM + #elif HAS_FREE_AUX2_PINS // try to use AUX 2 + #define CASE_LIGHT_PIN 44 // Hardware PWM #endif #endif @@ -230,13 +232,13 @@ // M3/M4/M5 - Spindle/Laser Control // #if HAS_CUTTER && !PIN_EXISTS(SPINDLE_LASER_ENA) - #if !defined(NUM_SERVOS) || NUM_SERVOS == 0 // try to use servo connector first - #define SPINDLE_LASER_ENA_PIN 4 // Pin should have a pullup/pulldown! - #define SPINDLE_LASER_PWM_PIN 6 // MUST BE HARDWARE PWM + #if !defined(NUM_SERVOS) || NUM_SERVOS == 0 // Prefer the servo connector + #define SPINDLE_LASER_ENA_PIN 4 // Pullup or pulldown! + #define SPINDLE_LASER_PWM_PIN 6 // Hardware PWM #define SPINDLE_DIR_PIN 5 - #elif !(BOTH(ULTRA_LCD, NEWPANEL) && ANY(PANEL_ONE, VIKI2, miniVIKI, MINIPANEL, REPRAPWORLD_KEYPAD)) // try to use AUX 2 - #define SPINDLE_LASER_ENA_PIN 40 // Pin should have a pullup/pulldown! - #define SPINDLE_LASER_PWM_PIN 44 // MUST BE HARDWARE PWM + #elif HAS_FREE_AUX2_PINS // try to use AUX 2 + #define SPINDLE_LASER_ENA_PIN 40 // Pullup or pulldown! + #define SPINDLE_LASER_PWM_PIN 44 // Hardware PWM #define SPINDLE_DIR_PIN 65 #endif #endif @@ -269,7 +271,7 @@ #endif #endif -#if HAS_DRIVER(TMC2208) || HAS_DRIVER(TMC2209) +#if HAS_TMC220x /** * TMC2208/TMC2209 stepper drivers * @@ -292,31 +294,75 @@ * Software serial */ - #define X_SERIAL_TX_PIN 40 - #define X_SERIAL_RX_PIN 63 - #define X2_SERIAL_TX_PIN -1 - #define X2_SERIAL_RX_PIN -1 + #ifndef X_SERIAL_TX_PIN + #define X_SERIAL_TX_PIN 40 + #endif + #ifndef X_SERIAL_RX_PIN + #define X_SERIAL_RX_PIN 63 + #endif + #ifndef X2_SERIAL_TX_PIN + #define X2_SERIAL_TX_PIN -1 + #endif + #ifndef X2_SERIAL_RX_PIN + #define X2_SERIAL_RX_PIN -1 + #endif - #define Y_SERIAL_TX_PIN 59 - #define Y_SERIAL_RX_PIN 64 - #define Y2_SERIAL_TX_PIN -1 - #define Y2_SERIAL_RX_PIN -1 + #ifndef Y_SERIAL_TX_PIN + #define Y_SERIAL_TX_PIN 59 + #endif + #ifndef Y_SERIAL_RX_PIN + #define Y_SERIAL_RX_PIN 64 + #endif + #ifndef Y2_SERIAL_TX_PIN + #define Y2_SERIAL_TX_PIN -1 + #endif + #ifndef Y2_SERIAL_RX_PIN + #define Y2_SERIAL_RX_PIN -1 + #endif - #define Z_SERIAL_TX_PIN 42 - #define Z_SERIAL_RX_PIN 65 - #define Z2_SERIAL_TX_PIN -1 - #define Z2_SERIAL_RX_PIN -1 + #ifndef Z_SERIAL_TX_PIN + #define Z_SERIAL_TX_PIN 42 + #endif + #ifndef Z_SERIAL_RX_PIN + #define Z_SERIAL_RX_PIN 65 + #endif + #ifndef Z2_SERIAL_TX_PIN + #define Z2_SERIAL_TX_PIN -1 + #endif + #ifndef Z2_SERIAL_RX_PIN + #define Z2_SERIAL_RX_PIN -1 + #endif - #define E0_SERIAL_TX_PIN 44 - #define E0_SERIAL_RX_PIN 66 - #define E1_SERIAL_TX_PIN -1 - #define E1_SERIAL_RX_PIN -1 - #define E2_SERIAL_TX_PIN -1 - #define E2_SERIAL_RX_PIN -1 - #define E3_SERIAL_TX_PIN -1 - #define E3_SERIAL_RX_PIN -1 - #define E4_SERIAL_TX_PIN -1 - #define E4_SERIAL_RX_PIN -1 + #ifndef E0_SERIAL_TX_PIN + #define E0_SERIAL_TX_PIN 44 + #endif + #ifndef E0_SERIAL_RX_PIN + #define E0_SERIAL_RX_PIN 66 + #endif + #ifndef E1_SERIAL_TX_PIN + #define E1_SERIAL_TX_PIN -1 + #endif + #ifndef E1_SERIAL_RX_PIN + #define E1_SERIAL_RX_PIN -1 + #endif + #ifndef E2_SERIAL_TX_PIN + #define E2_SERIAL_TX_PIN -1 + #endif + #ifndef E2_SERIAL_RX_PIN + #define E2_SERIAL_RX_PIN -1 + #endif + #ifndef E3_SERIAL_TX_PIN + #define E3_SERIAL_TX_PIN -1 + #endif + #ifndef E3_SERIAL_RX_PIN + #define E3_SERIAL_RX_PIN -1 + #endif + #ifndef E4_SERIAL_TX_PIN + #define E4_SERIAL_TX_PIN -1 + #endif + #ifndef E4_SERIAL_RX_PIN + #define E4_SERIAL_RX_PIN -1 + #endif #endif ////////////////////////// @@ -540,7 +586,7 @@ // Beeper on AUX-4 #define BEEPER_PIN 33 - // Buttons are directly attached using AUX-2 + // Buttons are directly attached to AUX-2 #if ENABLED(REPRAPWORLD_KEYPAD) #define SHIFT_OUT 40 #define SHIFT_CLK 44 diff --git a/Marlin/src/pins/pins_AZSMZ_MINI.h b/Marlin/src/pins/lpc1768/pins_AZSMZ_MINI.h similarity index 100% rename from Marlin/src/pins/pins_AZSMZ_MINI.h rename to Marlin/src/pins/lpc1768/pins_AZSMZ_MINI.h diff --git a/Marlin/src/pins/pins_BIQU_SKR_V1.1.h b/Marlin/src/pins/lpc1768/pins_BIGTREE_SKR_V1.1.h similarity index 99% rename from Marlin/src/pins/pins_BIQU_SKR_V1.1.h rename to Marlin/src/pins/lpc1768/pins_BIGTREE_SKR_V1.1.h index 4dbd0e6c12..d4ead0f4f7 100644 --- a/Marlin/src/pins/pins_BIQU_SKR_V1.1.h +++ b/Marlin/src/pins/lpc1768/pins_BIGTREE_SKR_V1.1.h @@ -25,9 +25,7 @@ #error "Oops! Make sure you have the LPC1768 environment selected in your IDE." #endif -#ifndef BOARD_NAME - #define BOARD_NAME "BIQU SKR V1.1" -#endif +#define BOARD_NAME "BIGTREE SKR 1.1" // // Limit Switches diff --git a/Marlin/src/pins/pins_BIGTREE_SKR_V1.3.h b/Marlin/src/pins/lpc1768/pins_BIGTREE_SKR_V1.3.h similarity index 95% rename from Marlin/src/pins/pins_BIGTREE_SKR_V1.3.h rename to Marlin/src/pins/lpc1768/pins_BIGTREE_SKR_V1.3.h index c6e64f1654..f84eafdf8c 100644 --- a/Marlin/src/pins/pins_BIGTREE_SKR_V1.3.h +++ b/Marlin/src/pins/lpc1768/pins_BIGTREE_SKR_V1.3.h @@ -25,12 +25,10 @@ #error "Oops! Make sure you have the LPC1768 environment selected in your IDE." #endif -#ifndef BOARD_NAME - #define BOARD_NAME "BIGTREE SKR V1.3" -#endif +#define BOARD_NAME "BIGTREE SKR 1.3" -// Ignore temp readings during develpment. -//#define BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE +// Ignore temp readings during development. +//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000 // // Servos @@ -103,13 +101,19 @@ // Software SPI pins for TMC2130 stepper drivers // #if ENABLED(TMC_USE_SW_SPI) - #define TMC_SW_MOSI P4_28 - #define TMC_SW_MISO P0_05 - #define TMC_SW_SCK P0_04 + #ifndef TMC_SW_MOSI + #define TMC_SW_MOSI P4_28 + #endif + #ifndef TMC_SW_MISO + #define TMC_SW_MISO P0_05 + #endif + #ifndef TMC_SW_SCK + #define TMC_SW_SCK P0_04 + #endif #endif -#if HAS_DRIVER(TMC2208) || HAS_DRIVER(TMC2209) - /** +#if HAS_TMC220x + /** * TMC2208/TMC2209 stepper drivers * * Hardware serial communication ports. diff --git a/Marlin/src/pins/pins_BIQU_B300_V1.0.h b/Marlin/src/pins/lpc1768/pins_BIQU_B300_V1.0.h similarity index 95% rename from Marlin/src/pins/pins_BIQU_B300_V1.0.h rename to Marlin/src/pins/lpc1768/pins_BIQU_B300_V1.0.h index a05ebd99f0..426a20653d 100644 --- a/Marlin/src/pins/pins_BIQU_B300_V1.0.h +++ b/Marlin/src/pins/lpc1768/pins_BIQU_B300_V1.0.h @@ -83,9 +83,15 @@ // Software SPI pins for TMC2130 stepper drivers // #if ENABLED(TMC_USE_SW_SPI) - #define TMC_SW_MOSI P0_18 // ETH - #define TMC_SW_MISO P0_17 // ETH - #define TMC_SW_SCK P0_15 // ETH + #ifndef TMC_SW_MOSI + #define TMC_SW_MOSI P0_18 // ETH + #endif + #ifndef TMC_SW_MISO + #define TMC_SW_MISO P0_17 // ETH + #endif + #ifndef TMC_SW_SCK + #define TMC_SW_SCK P0_15 // ETH + #endif #endif // diff --git a/Marlin/src/pins/pins_BIQU_BQ111_A4.h b/Marlin/src/pins/lpc1768/pins_BIQU_BQ111_A4.h similarity index 100% rename from Marlin/src/pins/pins_BIQU_BQ111_A4.h rename to Marlin/src/pins/lpc1768/pins_BIQU_BQ111_A4.h diff --git a/Marlin/src/pins/lpc1768/pins_GMARSH_X6_REV1.h b/Marlin/src/pins/lpc1768/pins_GMARSH_X6_REV1.h new file mode 100644 index 0000000000..e2a3d6dc19 --- /dev/null +++ b/Marlin/src/pins/lpc1768/pins_GMARSH_X6_REV1.h @@ -0,0 +1,160 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +#ifndef TARGET_LPC1768 + #error "Oops! Make sure you have the LPC1768 environment selected in your IDE." +#endif + +#define BOARD_NAME "GMARSH X6 REV1" + +// Ignore temp readings during develpment. +//#define BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE + +// +// Enable 12MHz clock output on P1.27 pin to sync TMC2208 chip clocks +// +#define LPC1768_ENABLE_CLKOUT_12M + +// +// Servos +// +#define SERVO0_PIN P1_26 // PWM1[6] +#define SERVO1_PIN P1_18 // PWM1[1] + +// +// Limit Switches +// +#define X_MIN_PIN P0_00 +#define X_MAX_PIN P0_01 +#define Y_MIN_PIN P0_10 +#define Y_MAX_PIN P0_21 +#define Z_MIN_PIN P2_13 +#define Z_MAX_PIN P2_22 + +// +// Steppers +// + +#define X_STEP_PIN P1_01 +#define X_DIR_PIN P1_04 +#define X_ENABLE_PIN P0_26 + +#define Y_STEP_PIN P1_10 +#define Y_DIR_PIN P1_14 +#define Y_ENABLE_PIN P1_08 + +#define Z_STEP_PIN P1_17 +#define Z_DIR_PIN P4_29 +#define Z_ENABLE_PIN P1_15 + +#define E0_STEP_PIN P0_05 +#define E0_DIR_PIN P2_00 +#define E0_ENABLE_PIN P4_28 + +#define E1_STEP_PIN P2_03 +#define E1_DIR_PIN P2_04 +#define E1_ENABLE_PIN P2_01 + +#define E2_STEP_PIN P2_07 +#define E2_DIR_PIN P2_08 +#define E2_ENABLE_PIN P2_05 + +// +// TMC2208 UART pins +// +#if HAS_DRIVER(TMC2208) + #define X_SERIAL_TX_PIN P1_00 + #define X_SERIAL_RX_PIN P1_00 + #define Y_SERIAL_TX_PIN P1_09 + #define Y_SERIAL_RX_PIN P1_09 + #define Z_SERIAL_TX_PIN P1_16 + #define Z_SERIAL_RX_PIN P1_16 + #define E0_SERIAL_TX_PIN P0_04 + #define E0_SERIAL_RX_PIN P0_04 + #define E1_SERIAL_TX_PIN P2_02 + #define E1_SERIAL_RX_PIN P2_02 + #define E2_SERIAL_TX_PIN P2_06 + #define E2_SERIAL_RX_PIN P2_06 +#else + #error "TMC2208 UART configuration is required for GMarsh X6." +#endif + +// +// Temperature Sensors +// 3.3V max when defined as an analog input +// +#define TEMP_0_PIN 1 // AD0[0] on P0_23 +#define TEMP_BED_PIN 0 // AD0[1] on P0_24 + +// +// Heaters / Fans +// +#define HEATER_BED_PIN P1_19 // Not a PWM pin, software PWM required +#define HEATER_0_PIN P3_26 // PWM1[3] +#define FAN_PIN P3_25 // Part cooling fan - connected to PWM1[2] +#define E0_AUTO_FAN_PIN P0_27 // Extruder cooling fan + +// +// Misc. Functions +// +#define LED_PIN P1_31 + +// +// LCD +// +#if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) + #define BEEPER_PIN P0_19 + #define BTN_EN1 P1_23 + #define BTN_EN2 P1_24 + #define BTN_ENC P1_25 + #define LCD_PINS_RS P0_20 + #define LCD_PINS_ENABLE P0_21 + #define LCD_PINS_D4 P2_11 + #define LCD_PINS_D5 P0_22 + #define LCD_PINS_D6 P1_29 + #define LCD_PINS_D7 P1_28 +#endif + +// +// SD Support +// + +#ifndef SDCARD_CONNECTION + #define SDCARD_CONNECTION LCD +#endif + +#define ONBOARD_SD_CS_PIN P0_06 // Chip select for "System" SD card + +#if SD_CONNECTION_IS(LCD) + #define SCK_PIN P0_15 + #define MISO_PIN P0_17 + #define MOSI_PIN P0_18 + #define SS_PIN P0_16 +#elif SD_CONNECTION_IS(ONBOARD) + #undef SD_DETECT_PIN + #define SD_DETECT_PIN P0_27 + #define SCK_PIN P0_07 + #define MISO_PIN P0_08 + #define MOSI_PIN P0_09 + #define SS_PIN ONBOARD_SD_CS_PIN +#endif diff --git a/Marlin/src/pins/pins_MKS_SBASE.h b/Marlin/src/pins/lpc1768/pins_MKS_SBASE.h similarity index 91% rename from Marlin/src/pins/pins_MKS_SBASE.h rename to Marlin/src/pins/lpc1768/pins_MKS_SBASE.h index 2d37f7274e..b3d307d3bf 100644 --- a/Marlin/src/pins/pins_MKS_SBASE.h +++ b/Marlin/src/pins/lpc1768/pins_MKS_SBASE.h @@ -231,36 +231,36 @@ #if ENABLED(FYSETC_MINI_12864) /** - * The Fysetc display can NOT use the SCK and MOSI pins on EXP2, so a + * The FYSETC display can NOT use the SCK and MOSI pins on EXP2, so a * special cable is needed to go between EXP2 on the FYSETC and the * controller board's EXP2 and J8. It also means that a software SPI * is needed to drive those pins. * - * The Fysetc requires mode 3 SPI interface. + * The FYSETC requires mode 3 SPI interface. * * Pins 6, 7 & 8 on EXP2 are no connects. That means a second special * cable will be needed if the RGB LEDs are to be active. */ - #define DOGLCD_CS LCD_PINS_ENABLE // EXP1.3 (LCD_EN on Fysetc schematic) - #define DOGLCD_A0 LCD_PINS_RS // EXP1.4 (LCD_A0 on Fysetc schematic) - #define DOGLCD_SCK P2_11 // J8-5 (SCK on Fysetc schematic) - #define DOGLCD_MOSI P4_28 // J8-6 (MOSI on Fysetc schematic) + #define DOGLCD_CS LCD_PINS_ENABLE // EXP1.3 (LCD_EN on FYSETC schematic) + #define DOGLCD_A0 LCD_PINS_RS // EXP1.4 (LCD_A0 on FYSETC schematic) + #define DOGLCD_SCK P2_11 // J8-5 (SCK on FYSETC schematic) + #define DOGLCD_MOSI P4_28 // J8-6 (MOSI on FYSETC schematic) //#define FORCE_SOFT_SPI // Use this if default of hardware SPI causes display problems // results in LCD soft SPI mode 3, SD soft SPI mode 0 #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0) #ifndef RGB_LED_R_PIN - #define RGB_LED_R_PIN P2_12 // J8-4 (LCD_D6 on Fysetc schematic) + #define RGB_LED_R_PIN P2_12 // J8-4 (LCD_D6 on FYSETC schematic) #endif #ifndef RGB_LED_G_PIN - #define RGB_LED_G_PIN P1_23 // J8-3 (LCD_D5 on Fysetc schematic) + #define RGB_LED_G_PIN P1_23 // J8-3 (LCD_D5 on FYSETC schematic) #endif #ifndef RGB_LED_B_PIN - #define RGB_LED_B_PIN P1_22 // J8-2 (LCD_D7 on Fysetc schematic) + #define RGB_LED_B_PIN P1_22 // J8-2 (LCD_D7 on FYSETC schematic) #endif #elif ENABLED(FYSETC_MINI_12864_2_1) - #define NEOPIXEL_PIN P2_12 + #define NEOPIXEL_PIN P2_12 #endif #elif ENABLED(MINIPANEL) @@ -303,10 +303,15 @@ #endif #endif -#if MB(MKS_SBASE) && (HAS_DRIVER(TMC2208) || HAS_DRIVER(TMC2209)) - // The shortage of pins becomes apparent. - // Worst case you may have to give up the LCD - // RX pins need to be interrupt capable +#if MB(MKS_SBASE) && HAS_TMC220x + + /** + * TMC2208/TMC2209 stepper drivers + * + * The shortage of pins becomes apparent. + * Worst case you may have to give up the LCD + * RX pins need to be interrupt capable + */ #define X_SERIAL_TX_PIN P1_22 // J8-2 #define X_SERIAL_RX_PIN P2_12 // J8-4 Interrupt Capable #define Y_SERIAL_TX_PIN P1_23 // J8-3 @@ -344,26 +349,26 @@ * PWM1.6 P2_05 RAMPS_D10_PIN */ - /** - * Special pins - * P1_30 - not 5V tolerant - EXP1 - * P1_31 - not 5V tolerant - EXP1 - * P0_27 - open collector - EXP2 - * P0_28 - open collector - EXP2 - * - */ +/** + * Special pins + * P1_30 - not 5V tolerant - EXP1 + * P1_31 - not 5V tolerant - EXP1 + * P0_27 - open collector - EXP2 + * P0_28 - open collector - EXP2 + * + */ - /** - * Serial Ports - * P0_00 - Port 3 - * P0_01 - SD Card (Onboard) - * P0_10 - Port 2 - * P0_11 - Y_EN/Y_DIR - * P0_15 - Port 1 - * P0_16 - EXP1 - * P0_02 - Port 0 - * P0_03 - AUX1 - * P0_29 - Port -1 - * P0_30 - USB - * - */ +/** + * Serial Ports + * P0_00 - Port 3 + * P0_01 - SD Card (Onboard) + * P0_10 - Port 2 + * P0_11 - Y_EN/Y_DIR + * P0_15 - Port 1 + * P0_16 - EXP1 + * P0_02 - Port 0 + * P0_03 - AUX1 + * P0_29 - Port -1 + * P0_30 - USB + * + */ diff --git a/Marlin/src/pins/pins_MKS_SGEN_L.h b/Marlin/src/pins/lpc1768/pins_MKS_SGEN_L.h similarity index 95% rename from Marlin/src/pins/pins_MKS_SGEN_L.h rename to Marlin/src/pins/lpc1768/pins_MKS_SGEN_L.h index d0ff839a07..3207309c50 100644 --- a/Marlin/src/pins/pins_MKS_SGEN_L.h +++ b/Marlin/src/pins/lpc1768/pins_MKS_SGEN_L.h @@ -29,7 +29,7 @@ #error "Oops! Make sure you have the LPC1768 environment selected in your IDE." #endif -#define BOARD_NAME "MKS SGEN-L" +#define BOARD_NAME "MKS SGen-L" #define BOARD_WEBSITE_URL "https://github.com/makerbase-mks/MKS-SGEN_L" // @@ -97,14 +97,20 @@ // Software SPI pins for TMC2130 stepper drivers // #if ENABLED(TMC_USE_SW_SPI) - #define TMC_SW_MOSI P4_28 - #define TMC_SW_MISO P0_05 - #define TMC_SW_SCK P0_04 + #ifndef TMC_SW_MOSI + #define TMC_SW_MOSI P4_28 + #endif + #ifndef TMC_SW_MISO + #define TMC_SW_MISO P0_05 + #endif + #ifndef TMC_SW_SCK + #define TMC_SW_SCK P0_04 + #endif #endif -#if HAS_DRIVER(TMC2208) || HAS_DRIVER(TMC2209) +#if HAS_TMC220x /** - * TMC2208 stepper drivers + * TMC2208/TMC2209 stepper drivers * * Hardware serial communication ports. * If undefined software serial is used according to the pins below @@ -186,7 +192,7 @@ #define BTN_ENC P1_30 #if ENABLED(CR10_STOCKDISPLAY) - #define LCD_PINS_RS P1_0 + #define LCD_PINS_RS P1_00 #define BTN_EN1 P0_18 #define BTN_EN2 P0_15 diff --git a/Marlin/src/pins/pins_RAMPS_RE_ARM.h b/Marlin/src/pins/lpc1768/pins_RAMPS_RE_ARM.h similarity index 90% rename from Marlin/src/pins/pins_RAMPS_RE_ARM.h rename to Marlin/src/pins/lpc1768/pins_RAMPS_RE_ARM.h index b6da047e44..802fc9fe7d 100644 --- a/Marlin/src/pins/pins_RAMPS_RE_ARM.h +++ b/Marlin/src/pins/lpc1768/pins_RAMPS_RE_ARM.h @@ -102,12 +102,18 @@ // Software SPI pins for TMC2130 stepper drivers // #if ENABLED(TMC_USE_SW_SPI) - #define TMC_SW_MOSI P1_00 // ETH - #define TMC_SW_MISO P1_08 // ETH - #define TMC_SW_SCK P1_09 // ETH + #ifndef TMC_SW_MOSI + #define TMC_SW_MOSI P1_00 // ETH + #endif + #ifndef TMC_SW_MISO + #define TMC_SW_MISO P1_08 // ETH + #endif + #ifndef TMC_SW_SCK + #define TMC_SW_SCK P1_09 // ETH + #endif #endif -#if HAS_DRIVER(TMC2208) || HAS_DRIVER(TMC2209) +#if HAS_TMC220x /** * TMC2208/TMC2209 stepper drivers * @@ -115,24 +121,24 @@ * If undefined software serial is used according to the pins below */ - /** - * Software serial - */ + // + // Software serial + // - // P2_08 E1-Step - // P2_13 E1-Dir + // P2_08 E1-Step + // P2_13 E1-Dir - #define X_SERIAL_TX_PIN P2_13 - #define X_SERIAL_RX_PIN P2_13 + #define X_SERIAL_TX_PIN P2_13 + #define X_SERIAL_RX_PIN P2_13 - #define Y_SERIAL_TX_PIN P0_00 - #define Y_SERIAL_RX_PIN P0_00 + #define Y_SERIAL_TX_PIN P0_00 + #define Y_SERIAL_RX_PIN P0_00 - #define Z_SERIAL_TX_PIN P0_01 - #define Z_SERIAL_RX_PIN P0_01 + #define Z_SERIAL_TX_PIN P0_01 + #define Z_SERIAL_RX_PIN P0_01 - #define E0_SERIAL_TX_PIN P2_08 - #define E0_SERIAL_RX_PIN P2_08 + #define E0_SERIAL_TX_PIN P2_08 + #define E0_SERIAL_RX_PIN P2_08 #endif @@ -152,7 +158,7 @@ // // Augmentation for auto-assigning RAMPS plugs // -#if DISABLED(IS_RAMPS_EEB, IS_RAMPS_EEF, IS_RAMPS_EFB, IS_RAMPS_EFF, IS_RAMPS_SF) && !PIN_EXISTS(MOSFET_D) +#if NONE(IS_RAMPS_EEB, IS_RAMPS_EEF, IS_RAMPS_EFB, IS_RAMPS_EFF, IS_RAMPS_SF) && !PIN_EXISTS(MOSFET_D) #if HOTENDS > 1 #if TEMP_SENSOR_BED #define IS_RAMPS_EEB @@ -248,9 +254,9 @@ #error "LASER_FEATURE requires 3 free servo pins." #endif #endif - #define SPINDLE_LASER_ENA_PIN SERVO1_PIN // (6) Pin should have a pullup/pulldown! - #define SPINDLE_LASER_PWM_PIN SERVO3_PIN // (4) MUST BE HARDWARE PWM - #define SPINDLE_DIR_PIN SERVO2_PIN // (5) + #define SPINDLE_LASER_ENA_PIN SERVO1_PIN // (6) Pin should have a pullup/pulldown! + #define SPINDLE_LASER_PWM_PIN SERVO3_PIN // (4) MUST BE HARDWARE PWM + #define SPINDLE_DIR_PIN SERVO2_PIN // (5) #endif // @@ -303,10 +309,10 @@ #elif HAS_SPI_LCD - //#define SCK_PIN P0_15 // (52) system defined J3-9 & AUX-3 - //#define MISO_PIN P0_17 // (50) system defined J3-10 & AUX-3 - //#define MOSI_PIN P0_18 // (51) system defined J3-10 & AUX-3 - //#define SS_PIN P1_23 // (53) system defined J3-5 & AUX-3 (Sometimes called SDSS) + //#define SCK_PIN P0_15 // (52) system defined J3-9 & AUX-3 + //#define MISO_PIN P0_17 // (50) system defined J3-10 & AUX-3 + //#define MOSI_PIN P0_18 // (51) system defined J3-10 & AUX-3 + //#define SS_PIN P1_23 // (53) system defined J3-5 & AUX-3 (Sometimes called SDSS) #if ENABLED(FYSETC_MINI_12864) #define BEEPER_PIN P1_01 @@ -331,10 +337,10 @@ #define SHIFT_LD P1_31 // (49) J3-1 & AUX-3 (NOT 5V tolerant) #endif #else - //#define SHIFT_CLK P3_26 // (31) J3-2 & AUX-4 - //#define SHIFT_LD P3_25 // (33) J3-4 & AUX-4 - //#define SHIFT_OUT P2_11 // (35) J3-3 & AUX-4 - //#define SHIFT_EN P1_22 // (41) J5-4 & AUX-4 + //#define SHIFT_CLK P3_26 // (31) J3-2 & AUX-4 + //#define SHIFT_LD P3_25 // (33) J3-4 & AUX-4 + //#define SHIFT_OUT P2_11 // (35) J3-3 & AUX-4 + //#define SHIFT_EN P1_22 // (41) J5-4 & AUX-4 #endif #if ANY(VIKI2, miniVIKI) @@ -359,7 +365,7 @@ //#define FORCE_SOFT_SPI // Use this if default of hardware SPI causes display problems // results in LCD soft SPI mode 3, SD soft SPI mode 0 - #define LCD_RESET_PIN P0_16 // Must be high or open for LCD to operate normally. + #define LCD_RESET_PIN P0_16 // Must be high or open for LCD to operate normally. #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0) #ifndef RGB_LED_R_PIN @@ -372,7 +378,7 @@ #define RGB_LED_B_PIN P1_08 #endif #elif ENABLED(FYSETC_MINI_12864_2_1) - #define NEOPIXEL_PIN P1_00 + #define NEOPIXEL_PIN P1_00 #endif #else #define DOGLCD_CS P0_26 // (63) J5-3 & AUX-2 diff --git a/Marlin/src/pins/pins_SELENA_COMPACT.h b/Marlin/src/pins/lpc1768/pins_SELENA_COMPACT.h similarity index 100% rename from Marlin/src/pins/pins_SELENA_COMPACT.h rename to Marlin/src/pins/lpc1768/pins_SELENA_COMPACT.h diff --git a/Marlin/src/pins/pins_TH3D_EZBOARD.h b/Marlin/src/pins/lpc1768/pins_TH3D_EZBOARD.h similarity index 100% rename from Marlin/src/pins/pins_TH3D_EZBOARD.h rename to Marlin/src/pins/lpc1768/pins_TH3D_EZBOARD.h diff --git a/Marlin/src/pins/pins_AZTEEG_X5_GT.h b/Marlin/src/pins/lpc1769/pins_AZTEEG_X5_GT.h similarity index 96% rename from Marlin/src/pins/pins_AZTEEG_X5_GT.h rename to Marlin/src/pins/lpc1769/pins_AZTEEG_X5_GT.h index 11dd45a6a5..fed88b4656 100644 --- a/Marlin/src/pins/pins_AZTEEG_X5_GT.h +++ b/Marlin/src/pins/lpc1769/pins_AZTEEG_X5_GT.h @@ -30,7 +30,7 @@ #endif #define BOARD_NAME "Azteeg X5 GT" -#define BOARD_WEBSITE_URL "https://www.panucatt.com/azteeg_X5_GT_reprap_3d_printer_controller_p/ax5gt.htm" +#define BOARD_WEBSITE_URL "https://tinyurl.com/yx8tdqa3" // // Set CPU diff --git a/Marlin/src/pins/pins_AZTEEG_X5_MINI.h b/Marlin/src/pins/lpc1769/pins_AZTEEG_X5_MINI.h similarity index 99% rename from Marlin/src/pins/pins_AZTEEG_X5_MINI.h rename to Marlin/src/pins/lpc1769/pins_AZTEEG_X5_MINI.h index 41936bd6d0..a685480757 100644 --- a/Marlin/src/pins/pins_AZTEEG_X5_MINI.h +++ b/Marlin/src/pins/lpc1769/pins_AZTEEG_X5_MINI.h @@ -30,7 +30,7 @@ #endif #ifndef BOARD_NAME - #define BOARD_NAME "Azteeg X5 MINI" + #define BOARD_NAME "Azteeg X5 MINI" #endif #define BOARD_WEBSITE_URL "http://www.panucatt.com/azteeg_X5_mini_reprap_3d_printer_controller_p/ax5mini.htm" diff --git a/Marlin/src/pins/pins_AZTEEG_X5_MINI_WIFI.h b/Marlin/src/pins/lpc1769/pins_AZTEEG_X5_MINI_WIFI.h similarity index 96% rename from Marlin/src/pins/pins_AZTEEG_X5_MINI_WIFI.h rename to Marlin/src/pins/lpc1769/pins_AZTEEG_X5_MINI_WIFI.h index 03005ecb4f..6cbdb335f3 100644 --- a/Marlin/src/pins/pins_AZTEEG_X5_MINI_WIFI.h +++ b/Marlin/src/pins/lpc1769/pins_AZTEEG_X5_MINI_WIFI.h @@ -29,7 +29,7 @@ #error "Oops! Make sure you have the LPC1769 environment selected in your IDE." #endif -#define BOARD_NAME "Azteeg X5 MINI WIFI" +#define BOARD_NAME "Azteeg X5 MINI WIFI" // // DIGIPOT slave addresses diff --git a/Marlin/src/pins/pins_COHESION3D_MINI.h b/Marlin/src/pins/lpc1769/pins_COHESION3D_MINI.h similarity index 100% rename from Marlin/src/pins/pins_COHESION3D_MINI.h rename to Marlin/src/pins/lpc1769/pins_COHESION3D_MINI.h diff --git a/Marlin/src/pins/pins_COHESION3D_REMIX.h b/Marlin/src/pins/lpc1769/pins_COHESION3D_REMIX.h similarity index 100% rename from Marlin/src/pins/pins_COHESION3D_REMIX.h rename to Marlin/src/pins/lpc1769/pins_COHESION3D_REMIX.h diff --git a/Marlin/src/pins/pins_MKS_SGEN.h b/Marlin/src/pins/lpc1769/pins_MKS_SGEN.h similarity index 80% rename from Marlin/src/pins/pins_MKS_SGEN.h rename to Marlin/src/pins/lpc1769/pins_MKS_SGEN.h index 921ec60c36..bf6359f096 100644 --- a/Marlin/src/pins/pins_MKS_SGEN.h +++ b/Marlin/src/pins/lpc1769/pins_MKS_SGEN.h @@ -29,10 +29,10 @@ #error "Oops! Make sure you have the LPC1769 environment selected in your IDE." #endif -#define BOARD_NAME "MKS SGEN" +#define BOARD_NAME "MKS SGen" #define BOARD_WEBSITE_URL "https://github.com/makerbase-mks/MKS-SGEN" -#include "pins_MKS_SBASE.h" +#include "../lpc1768/pins_MKS_SBASE.h" #undef E1_STEP_PIN #undef E1_DIR_PIN @@ -40,13 +40,17 @@ //#undef BTN_EN1 //#undef BTN_EN2 -//#define BTN_EN1 P1_23 // EXP2.5 -//#define BTN_EN2 P1_22 // EXP2.3 +//#define BTN_EN1 P1_23 // EXP2.5 +//#define BTN_EN2 P1_22 // EXP2.3 -#if HAS_DRIVER(TMC2208) || HAS_DRIVER(TMC2209) - // The shortage of pins becomes apparent. - // In the worst case you may have to give up the LCD. - // RX pins must be interrupt-capable. +#if HAS_TMC220x + /** + * TMC2208/TMC2209 stepper drivers + * + * The shortage of pins becomes apparent. + * In the worst case you may have to give up the LCD. + * RX pins must be interrupt-capable. + */ #define X_SERIAL_TX_PIN P4_29 // J8-2 #define X_SERIAL_RX_PIN P4_29 // J8-2 diff --git a/Marlin/src/pins/pins_SMOOTHIEBOARD.h b/Marlin/src/pins/lpc1769/pins_SMOOTHIEBOARD.h similarity index 100% rename from Marlin/src/pins/pins_SMOOTHIEBOARD.h rename to Marlin/src/pins/lpc1769/pins_SMOOTHIEBOARD.h diff --git a/Marlin/src/pins/pins_CHEAPTRONIC.h b/Marlin/src/pins/mega/pins_CHEAPTRONIC.h similarity index 100% rename from Marlin/src/pins/pins_CHEAPTRONIC.h rename to Marlin/src/pins/mega/pins_CHEAPTRONIC.h diff --git a/Marlin/src/pins/pins_CHEAPTRONICv2.h b/Marlin/src/pins/mega/pins_CHEAPTRONICv2.h similarity index 99% rename from Marlin/src/pins/pins_CHEAPTRONICv2.h rename to Marlin/src/pins/mega/pins_CHEAPTRONICv2.h index 111d76cd20..a409f03352 100644 --- a/Marlin/src/pins/pins_CHEAPTRONICv2.h +++ b/Marlin/src/pins/mega/pins_CHEAPTRONICv2.h @@ -125,7 +125,6 @@ #define BEEPER_PIN 44 #if ENABLED(SDSUPPORT) - #define SDPOWER -1 #define SDSS 53 #define SD_DETECT_PIN 49 #endif diff --git a/Marlin/src/pins/pins_CNCONTROLS_11.h b/Marlin/src/pins/mega/pins_CNCONTROLS_11.h similarity index 100% rename from Marlin/src/pins/pins_CNCONTROLS_11.h rename to Marlin/src/pins/mega/pins_CNCONTROLS_11.h diff --git a/Marlin/src/pins/pins_CNCONTROLS_12.h b/Marlin/src/pins/mega/pins_CNCONTROLS_12.h similarity index 100% rename from Marlin/src/pins/pins_CNCONTROLS_12.h rename to Marlin/src/pins/mega/pins_CNCONTROLS_12.h diff --git a/Marlin/src/pins/pins_EINSTART-S.h b/Marlin/src/pins/mega/pins_EINSTART-S.h similarity index 84% rename from Marlin/src/pins/pins_EINSTART-S.h rename to Marlin/src/pins/mega/pins_EINSTART-S.h index 4493602e25..78e2fe2c05 100644 --- a/Marlin/src/pins/pins_EINSTART-S.h +++ b/Marlin/src/pins/mega/pins_EINSTART-S.h @@ -26,16 +26,8 @@ * PCB Silkscreen: 3DPrinterCon_v3.5 */ -#if ENABLED(TARGET_LPC1768) - #error "Oops! Set MOTHERBOARD to an LPC1768-based board when building for LPC1768." -#elif defined(__STM32F1__) - #error "Oops! Set MOTHERBOARD to an STM32F1-based board when building for STM32F1." -#endif - -#if DISABLED(IS_RAMPS_SMART, IS_RAMPS_DUO, IS_RAMPS4DUE, TARGET_LPC1768) - #if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__) - #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'" - #endif +#if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__) + #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'" #endif #define BOARD_NAME "Einstart-S" diff --git a/Marlin/src/pins/pins_ELEFU_3.h b/Marlin/src/pins/mega/pins_ELEFU_3.h similarity index 100% rename from Marlin/src/pins/pins_ELEFU_3.h rename to Marlin/src/pins/mega/pins_ELEFU_3.h diff --git a/Marlin/src/pins/pins_GT2560_REV_A.h b/Marlin/src/pins/mega/pins_GT2560_REV_A.h similarity index 99% rename from Marlin/src/pins/pins_GT2560_REV_A.h rename to Marlin/src/pins/mega/pins_GT2560_REV_A.h index ba4f4830ac..3bc68cfd45 100644 --- a/Marlin/src/pins/pins_GT2560_REV_A.h +++ b/Marlin/src/pins/mega/pins_GT2560_REV_A.h @@ -89,7 +89,6 @@ // // Misc. Functions // -#define SDPOWER -1 #define SDSS 53 #define LED_PIN 13 #define PS_ON_PIN 12 diff --git a/Marlin/src/pins/pins_GT2560_REV_A_PLUS.h b/Marlin/src/pins/mega/pins_GT2560_REV_A_PLUS.h similarity index 100% rename from Marlin/src/pins/pins_GT2560_REV_A_PLUS.h rename to Marlin/src/pins/mega/pins_GT2560_REV_A_PLUS.h diff --git a/Marlin/src/pins/pins_GT2560_V3.h b/Marlin/src/pins/mega/pins_GT2560_V3.h similarity index 86% rename from Marlin/src/pins/pins_GT2560_V3.h rename to Marlin/src/pins/mega/pins_GT2560_V3.h index 4f0667d0b7..10db766da3 100644 --- a/Marlin/src/pins/pins_GT2560_V3.h +++ b/Marlin/src/pins/mega/pins_GT2560_V3.h @@ -149,15 +149,33 @@ // #define BEEPER_PIN 18 -#define LCD_PINS_RS 20 -#define LCD_PINS_ENABLE 17 -#define LCD_PINS_D4 16 -#define LCD_PINS_D5 21 -#define LCD_PINS_D6 5 -#define LCD_PINS_D7 36 +#ifndef LCD_PINS_RS + #define LCD_PINS_RS 20 +#endif +#ifndef LCD_PINS_ENABLE + #define LCD_PINS_ENABLE 17 +#endif +#ifndef LCD_PINS_D4 + #define LCD_PINS_D4 16 +#endif +#ifndef LCD_PINS_D5 + #define LCD_PINS_D5 21 +#endif +#ifndef LCD_PINS_D6 + #define LCD_PINS_D6 5 +#endif +#ifndef LCD_PINS_D7 + #define LCD_PINS_D7 36 +#endif #if ENABLED(NEWPANEL) - #define BTN_EN1 42 - #define BTN_EN2 40 - #define BTN_ENC 19 + #ifndef BTN_EN1 + #define BTN_EN1 42 + #endif + #ifndef BTN_EN2 + #define BTN_EN2 40 + #endif + #ifndef BTN_ENC + #define BTN_ENC 19 + #endif #endif diff --git a/Marlin/src/pins/pins_GT2560_V3_A20.h b/Marlin/src/pins/mega/pins_GT2560_V3_A20.h similarity index 89% rename from Marlin/src/pins/pins_GT2560_V3_A20.h rename to Marlin/src/pins/mega/pins_GT2560_V3_A20.h index 5565ac62cd..e3b6895af1 100644 --- a/Marlin/src/pins/pins_GT2560_V3_A20.h +++ b/Marlin/src/pins/mega/pins_GT2560_V3_A20.h @@ -25,22 +25,15 @@ * Geeetech A20M pin assignment */ -#include "pins_GT2560_V3.h" - -#undef LCD_PINS_RS -#undef LCD_PINS_ENABLE -#undef LCD_PINS_D4 -#undef LCD_PINS_D7 #define LCD_PINS_RS 5 #define LCD_PINS_ENABLE 36 #define LCD_PINS_D4 21 #define LCD_PINS_D7 6 #if ENABLED(NEWPANEL) - #undef BTN_EN1 - #undef BTN_EN2 - #undef BTN_ENC #define BTN_EN1 16 #define BTN_EN2 17 #define BTN_ENC 19 #endif + +#include "pins_GT2560_V3.h" diff --git a/Marlin/src/pins/pins_GT2560_V3_MC2.h b/Marlin/src/pins/mega/pins_GT2560_V3_MC2.h similarity index 100% rename from Marlin/src/pins/pins_GT2560_V3_MC2.h rename to Marlin/src/pins/mega/pins_GT2560_V3_MC2.h diff --git a/Marlin/src/pins/pins_LEAPFROG.h b/Marlin/src/pins/mega/pins_LEAPFROG.h similarity index 100% rename from Marlin/src/pins/pins_LEAPFROG.h rename to Marlin/src/pins/mega/pins_LEAPFROG.h diff --git a/Marlin/src/pins/pins_MEGACONTROLLER.h b/Marlin/src/pins/mega/pins_MEGACONTROLLER.h similarity index 95% rename from Marlin/src/pins/pins_MEGACONTROLLER.h rename to Marlin/src/pins/mega/pins_MEGACONTROLLER.h index 14fec34ec6..07fd91f73a 100644 --- a/Marlin/src/pins/pins_MEGACONTROLLER.h +++ b/Marlin/src/pins/mega/pins_MEGACONTROLLER.h @@ -27,9 +27,7 @@ #ifndef __AVR_ATmega2560__ #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'" -#endif - -#if HOTENDS > 2 || E_STEPPERS > 2 +#elif HOTENDS > 2 || E_STEPPERS > 2 #error "Mega Controller supports up to 2 hotends / E-steppers. Comment out this line to continue." #endif @@ -161,6 +159,6 @@ // // M3/M4/M5 - Spindle/Laser Control // -#define SPINDLE_LASER_PWM_PIN 6 // MUST BE HARDWARE PWM -#define SPINDLE_LASER_ENA_PIN 7 // Pin should have a pullup! +#define SPINDLE_LASER_PWM_PIN 6 // Hardware PWM +#define SPINDLE_LASER_ENA_PIN 7 // Pullup! #define SPINDLE_DIR_PIN 8 diff --git a/Marlin/src/pins/pins_MEGATRONICS.h b/Marlin/src/pins/mega/pins_MEGATRONICS.h similarity index 94% rename from Marlin/src/pins/pins_MEGATRONICS.h rename to Marlin/src/pins/mega/pins_MEGATRONICS.h index 44a487cbbc..c0b009392c 100644 --- a/Marlin/src/pins/pins_MEGATRONICS.h +++ b/Marlin/src/pins/mega/pins_MEGATRONICS.h @@ -114,7 +114,7 @@ #define LCD_PINS_D6 27 #define LCD_PINS_D7 29 - // Buttons directly attached using AUX-2 + // Buttons directly attached to AUX-2 #define BTN_EN1 59 #define BTN_EN2 64 #define BTN_ENC 43 @@ -126,6 +126,6 @@ // // M3/M4/M5 - Spindle/Laser Control // -#define SPINDLE_LASER_PWM_PIN 3 // MUST BE HARDWARE PWM -#define SPINDLE_LASER_ENA_PIN 4 // Pin should have a pullup! +#define SPINDLE_LASER_PWM_PIN 3 // Hardware PWM +#define SPINDLE_LASER_ENA_PIN 4 // Pullup! #define SPINDLE_DIR_PIN 11 diff --git a/Marlin/src/pins/pins_MEGATRONICS_2.h b/Marlin/src/pins/mega/pins_MEGATRONICS_2.h similarity index 95% rename from Marlin/src/pins/pins_MEGATRONICS_2.h rename to Marlin/src/pins/mega/pins_MEGATRONICS_2.h index fa154555f7..90ddc5cc0d 100644 --- a/Marlin/src/pins/pins_MEGATRONICS_2.h +++ b/Marlin/src/pins/mega/pins_MEGATRONICS_2.h @@ -29,7 +29,7 @@ #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'" #endif -#define BOARD_NAME "Megatronics v2.0" +#define BOARD_NAME "Megatronics v2.0" // // Limit Switches // @@ -141,6 +141,6 @@ // // M3/M4/M5 - Spindle/Laser Control // -#define SPINDLE_LASER_PWM_PIN 3 // MUST BE HARDWARE PWM -#define SPINDLE_LASER_ENA_PIN 16 // Pin should have a pullup! +#define SPINDLE_LASER_PWM_PIN 3 // Hardware PWM +#define SPINDLE_LASER_ENA_PIN 16 // Pullup! #define SPINDLE_DIR_PIN 11 diff --git a/Marlin/src/pins/pins_MEGATRONICS_3.h b/Marlin/src/pins/mega/pins_MEGATRONICS_3.h similarity index 94% rename from Marlin/src/pins/pins_MEGATRONICS_3.h rename to Marlin/src/pins/mega/pins_MEGATRONICS_3.h index 863680637f..77edc79e19 100644 --- a/Marlin/src/pins/pins_MEGATRONICS_3.h +++ b/Marlin/src/pins/mega/pins_MEGATRONICS_3.h @@ -174,8 +174,8 @@ // M3/M4/M5 - Spindle/Laser Control // #if DISABLED(REPRAPWORLD_KEYPAD) // try to use the keypad connector first - #define SPINDLE_LASER_PWM_PIN 44 // MUST BE HARDWARE PWM - #define SPINDLE_LASER_ENA_PIN 43 // Pin should have a pullup! + #define SPINDLE_LASER_PWM_PIN 44 // Hardware PWM + #define SPINDLE_LASER_ENA_PIN 43 // Pullup! #define SPINDLE_DIR_PIN 42 #elif EXTRUDERS <= 2 // Hijack the last extruder so that we can get the PWM signal off the Y breakout @@ -189,7 +189,7 @@ #define Y_ENABLE_PIN 23 #define Y_STEP_PIN 22 #define Y_DIR_PIN 60 - #define SPINDLE_LASER_PWM_PIN 4 // MUST BE HARDWARE PWM - #define SPINDLE_LASER_ENA_PIN 17 // Pin should have a pullup! + #define SPINDLE_LASER_PWM_PIN 4 // Hardware PWM + #define SPINDLE_LASER_ENA_PIN 17 // Pullup! #define SPINDLE_DIR_PIN 5 #endif diff --git a/Marlin/src/pins/pins_MIGHTYBOARD_REVE.h b/Marlin/src/pins/mega/pins_MIGHTYBOARD_REVE.h similarity index 98% rename from Marlin/src/pins/pins_MIGHTYBOARD_REVE.h rename to Marlin/src/pins/mega/pins_MIGHTYBOARD_REVE.h index 4cb4935252..4b93add4c0 100644 --- a/Marlin/src/pins/pins_MIGHTYBOARD_REVE.h +++ b/Marlin/src/pins/mega/pins_MIGHTYBOARD_REVE.h @@ -41,8 +41,8 @@ #error "Oops! Select 'Mega 1280' or 'Mega 2560' in 'Tools > Board.'" #endif -#define DEFAULT_MACHINE_NAME "MB Replicator" -#define BOARD_NAME "Mightyboard" +#define BOARD_NAME "Mightyboard" +#define DEFAULT_MACHINE_NAME "MB Replicator" // // Servos diff --git a/Marlin/src/pins/pins_MINITRONICS.h b/Marlin/src/pins/mega/pins_MINITRONICS.h similarity index 98% rename from Marlin/src/pins/pins_MINITRONICS.h rename to Marlin/src/pins/mega/pins_MINITRONICS.h index a76682a896..ad1b737e02 100644 --- a/Marlin/src/pins/pins_MINITRONICS.h +++ b/Marlin/src/pins/mega/pins_MINITRONICS.h @@ -34,9 +34,7 @@ #ifndef __AVR_ATmega1281__ #error "Oops! Select 'Minitronics' in 'Tools > Board.'" -#endif - -#if HOTENDS > 2 || E_STEPPERS > 2 +#elif HOTENDS > 2 || E_STEPPERS > 2 #error "Minitronics supports up to 2 hotends / E-steppers. Comment out this line to continue." #endif diff --git a/Marlin/src/pins/mega/pins_OVERLORD.h b/Marlin/src/pins/mega/pins_OVERLORD.h new file mode 100644 index 0000000000..8a9e3f5bda --- /dev/null +++ b/Marlin/src/pins/mega/pins_OVERLORD.h @@ -0,0 +1,144 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Dreammaker Overlord v1.1 pin assignments + */ + +#ifndef __AVR_ATmega2560__ + #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'" +#elif HOTENDS > 2 || E_STEPPERS > 2 + #error "Overlord Controller supports up to 2 hotends / E-steppers. Comment out this line to continue." +#endif + +#define BOARD_NAME "OVERLORD" +#define DEFAULT_MACHINE_NAME BOARD_NAME + +// +// Limit Switches +// +#define X_STOP_PIN 24 +#define Y_STOP_PIN 28 +#define Z_MIN_PIN 46 +#define Z_MAX_PIN 32 + +// +// Z Probe (when not Z_MIN_PIN) +// +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN 46 // JP4, Tfeed1 +#endif + +#if ENABLED(FILAMENT_RUNOUT_SENSOR) + #define FIL_RUNOUT_PIN 44 // JP3, Tfeed2 +#endif + +// +// Steppers +// +#define X_STEP_PIN 25 +#define X_DIR_PIN 23 +#define X_ENABLE_PIN 27 + +#define Y_STEP_PIN 31 +#define Y_DIR_PIN 33 +#define Y_ENABLE_PIN 29 + +#define Z_STEP_PIN 37 +#define Z_DIR_PIN 39 +#define Z_ENABLE_PIN 35 + +#define E0_STEP_PIN 43 +#define E0_DIR_PIN 45 +#define E0_ENABLE_PIN 41 + +#define E1_STEP_PIN 49 +#define E1_DIR_PIN 47 +#define E1_ENABLE_PIN 48 + +// +// Temperature Sensors +// +#define TEMP_0_PIN 8 // Analog Input +#define TEMP_1_PIN 9 // Analog Input - Redundant temp sensor +#define TEMP_2_PIN 12 // Analog Input +#define TEMP_3_PIN 14 // Analog Input +#define TEMP_BED_PIN 10 // Analog Input + +// +// Heaters / Fans +// +#define HEATER_0_PIN 2 +#define HEATER_1_PIN 3 +#define HEATER_BED_PIN 4 + +#define FAN_PIN 7 // material cooling fan + +// +// SD Card +// +#define SDSS 53 +#define SD_DETECT_PIN 38 + +// +// Misc. Functions +// +#define LED_PIN 13 // On PCB status led +#define PS_ON_PIN 12 // For stepper/heater/fan power. Active HIGH. +#define POWER_LOSS_PIN 34 // Power check - whether hotends/steppers/fans have power + +#if ENABLED(BATTERY_STATUS_AVAILABLE) + #undef BATTERY_STATUS_PIN + #define BATTERY_STATUS_PIN 26 // Status of power loss battery, whether it is charged (low) or charging (high) +#endif +#if ENABLED(INPUT_VOLTAGE_AVAILABLE) + #undef VOLTAGE_DETECTION_PIN + #define VOLTAGE_DETECTION_PIN 11 // Analog Input - ADC Voltage level of main input +#endif + +// +// LCD / Controller +// +#if HAS_GRAPHICAL_LCD + // OVERLORD OLED pins + #define LCD_PINS_RS 20 + #define LCD_PINS_D5 21 + #define LCD_PINS_ENABLE 15 + #define LCD_PINS_D4 14 + #define LCD_PINS_D6 5 + #define LCD_PINS_D7 6 + #ifndef LCD_RESET_PIN + #define LCD_RESET_PIN 5 // LCD_PINS_D6 + #endif +#endif + +#if ENABLED(NEWPANEL) + #define BTN_ENC 16 // Enter Pin + #define BTN_UP 19 // Button UP Pin + #define BTN_DWN 17 // Button DOWN Pin +#endif + +// Additional connectors/pins on the Overlord V1.X board +#define PCB_VERSION_PIN 22 +#define APPROACH_PIN 11 // JP7, Tpd +#define GATE_PIN 36 // Threshold, JP6, Tg diff --git a/Marlin/src/pins/pins_SILVER_GATE.h b/Marlin/src/pins/mega/pins_SILVER_GATE.h similarity index 100% rename from Marlin/src/pins/pins_SILVER_GATE.h rename to Marlin/src/pins/mega/pins_SILVER_GATE.h diff --git a/Marlin/src/pins/mega/pins_WANHAO_ONEPLUS.h b/Marlin/src/pins/mega/pins_WANHAO_ONEPLUS.h new file mode 100644 index 0000000000..86f295b622 --- /dev/null +++ b/Marlin/src/pins/mega/pins_WANHAO_ONEPLUS.h @@ -0,0 +1,111 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Wanhao 0ne+ pin assignments + */ + +#ifndef __AVR_ATmega2560__ + #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'" +#endif + +#define BOARD_NAME "Wanhao i3 Mini 0ne+" +#define DEFAULT_MACHINE_NAME "i3 Mini" +#define BOARD_WEBSITE_URL "https://tinyurl.com/yyxw7se7" + +// +// Limit Switches +// +#define X_STOP_PIN 19 +#define Y_STOP_PIN 18 +#define Z_STOP_PIN 38 + +// +// Z Probe (when not Z_MIN_PIN) +// +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN 38 +#endif + +// +// Steppers +// +#define X_STEP_PIN 22 +#define X_DIR_PIN 23 +#define X_ENABLE_PIN 57 + +#define Y_STEP_PIN 25 +#define Y_DIR_PIN 26 +#define Y_ENABLE_PIN 24 + +#define Z_STEP_PIN 29 +#define Z_DIR_PIN 39 +#define Z_ENABLE_PIN 28 + +#define E0_STEP_PIN 55 +#define E0_DIR_PIN 56 +#define E0_ENABLE_PIN 54 + +// +// Temperature Sensors +// +#define TEMP_0_PIN 13 +#define TEMP_BED_PIN 14 + +// +// Heaters / Fans +// +#define HEATER_0_PIN 4 +#define HEATER_BED_PIN 44 +#define FAN_PIN 12 // IO pin. Buffer needed + +// +// SD Card +// +#define SD_DETECT_PIN -1 +#define SDSS 53 + +// +// Misc. Functions +// +#define BEEPER_PIN 37 +#define KILL_PIN 64 + +// +// LCD / Controller +// + +#if HAS_SPI_LCD + #define DOGLCD_A0 40 + #define DOGLCD_CS 41 + #define LCD_BACKLIGHT_PIN 65 // Backlight LED on A11/D65 + #define LCD_RESET_PIN 27 + + #define LCD_CONTRAST 255 + + #if ENABLED(NEWPANEL) + #define BTN_EN1 2 + #define BTN_EN2 3 + #define BTN_ENC 5 + #endif +#endif diff --git a/Marlin/src/pins/pins.h b/Marlin/src/pins/pins.h index 4651faec45..6b0e5edbd9 100644 --- a/Marlin/src/pins/pins.h +++ b/Marlin/src/pins/pins.h @@ -47,449 +47,491 @@ #define IS_RAMPS_SF #endif +#define HAS_FREE_AUX2_PINS !(BOTH(ULTRA_LCD, NEWPANEL) && ANY(PANEL_ONE, VIKI2, miniVIKI, MINIPANEL, REPRAPWORLD_KEYPAD)) + // // RAMPS 1.3 / 1.4 - ATmega1280, ATmega2560 // #if MB(RAMPS_OLD) - #include "pins_RAMPS_OLD.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "ramps/pins_RAMPS_OLD.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(RAMPS_13_EFB) - #include "pins_RAMPS_13.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "ramps/pins_RAMPS_13.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(RAMPS_13_EEB) - #include "pins_RAMPS_13.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "ramps/pins_RAMPS_13.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(RAMPS_13_EFF) - #include "pins_RAMPS_13.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "ramps/pins_RAMPS_13.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(RAMPS_13_EEF) - #include "pins_RAMPS_13.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "ramps/pins_RAMPS_13.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(RAMPS_13_SF) - #include "pins_RAMPS_13.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "ramps/pins_RAMPS_13.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(RAMPS_14_EFB) - #include "pins_RAMPS.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "ramps/pins_RAMPS.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(RAMPS_14_EEB) - #include "pins_RAMPS.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "ramps/pins_RAMPS.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(RAMPS_14_EFF) - #include "pins_RAMPS.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "ramps/pins_RAMPS.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(RAMPS_14_EEF) - #include "pins_RAMPS.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "ramps/pins_RAMPS.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(RAMPS_14_SF) - #include "pins_RAMPS.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "ramps/pins_RAMPS.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(RAMPS_PLUS_EFB) - #include "pins_RAMPS_PLUS.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "ramps/pins_RAMPS_PLUS.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(RAMPS_PLUS_EEB) - #include "pins_RAMPS_PLUS.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "ramps/pins_RAMPS_PLUS.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(RAMPS_PLUS_EFF) - #include "pins_RAMPS_PLUS.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "ramps/pins_RAMPS_PLUS.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(RAMPS_PLUS_EEF) - #include "pins_RAMPS_PLUS.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "ramps/pins_RAMPS_PLUS.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(RAMPS_PLUS_SF) - #include "pins_RAMPS_PLUS.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "ramps/pins_RAMPS_PLUS.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 // // RAMPS Derivatives - ATmega1280, ATmega2560 // #elif MB(3DRAG) - #include "pins_3DRAG.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "ramps/pins_3DRAG.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(K8200) - #include "pins_K8200.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 (3DRAG) + #include "ramps/pins_K8200.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 (3DRAG) #elif MB(K8400) - #include "pins_K8400.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 (3DRAG) + #include "ramps/pins_K8400.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 (3DRAG) #elif MB(K8800) - #include "pins_K8800.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 (3DRAG) + #include "ramps/pins_K8800.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 (3DRAG) #elif MB(BAM_DICE) - #include "pins_RAMPS.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "ramps/pins_RAMPS.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(BAM_DICE_DUE) - #include "pins_BAM_DICE_DUE.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "ramps/pins_BAM_DICE_DUE.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(MKS_BASE) - #include "pins_MKS_BASE.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "ramps/pins_MKS_BASE.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(MKS_BASE_14) - #include "pins_MKS_BASE_14.h" // ATmega2560 env:megaatmega2560 + #include "ramps/pins_MKS_BASE_14.h" // ATmega2560 env:megaatmega2560 #elif MB(MKS_BASE_15) - #include "pins_MKS_BASE_15.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "ramps/pins_MKS_BASE_15.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(MKS_BASE_HEROIC) - #include "pins_MKS_BASE_HEROIC.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "ramps/pins_MKS_BASE_HEROIC.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(MKS_GEN_13) - #include "pins_MKS_GEN_13.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "ramps/pins_MKS_GEN_13.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(MKS_GEN_L) - #include "pins_MKS_GEN_L.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "ramps/pins_MKS_GEN_L.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(KFB_2) - #include "pins_BIQU_KFB_2.h" // ATmega2560 env:megaatmega2560 + #include "ramps/pins_BIQU_KFB_2.h" // ATmega2560 env:megaatmega2560 #elif MB(ZRIB_V20) - #include "pins_ZRIB_V20.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 (MKS_GEN_13) + #include "ramps/pins_ZRIB_V20.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 (MKS_GEN_13) #elif MB(FELIX2) - #include "pins_FELIX2.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "ramps/pins_FELIX2.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(RIGIDBOARD) - #include "pins_RIGIDBOARD.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "ramps/pins_RIGIDBOARD.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(RIGIDBOARD_V2) - #include "pins_RIGIDBOARD_V2.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "ramps/pins_RIGIDBOARD_V2.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(SAINSMART_2IN1) - #include "pins_SAINSMART_2IN1.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "ramps/pins_SAINSMART_2IN1.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(ULTIMAKER) - #include "pins_ULTIMAKER.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "ramps/pins_ULTIMAKER.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(ULTIMAKER_OLD) - #include "pins_ULTIMAKER_OLD.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "ramps/pins_ULTIMAKER_OLD.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(AZTEEG_X3) - #include "pins_AZTEEG_X3.h" // ATmega2560 env:megaatmega2560 + #include "ramps/pins_AZTEEG_X3.h" // ATmega2560 env:megaatmega2560 #elif MB(AZTEEG_X3_PRO) - #include "pins_AZTEEG_X3_PRO.h" // ATmega2560 env:megaatmega2560 + #include "ramps/pins_AZTEEG_X3_PRO.h" // ATmega2560 env:megaatmega2560 #elif MB(ULTIMAIN_2) - #include "pins_ULTIMAIN_2.h" // ATmega2560 env:megaatmega2560 + #include "ramps/pins_ULTIMAIN_2.h" // ATmega2560 env:megaatmega2560 #elif MB(FORMBOT_RAPTOR) - #include "pins_FORMBOT_RAPTOR.h" // ATmega2560 env:megaatmega2560 + #include "ramps/pins_FORMBOT_RAPTOR.h" // ATmega2560 env:megaatmega2560 #elif MB(FORMBOT_RAPTOR2) - #include "pins_FORMBOT_RAPTOR2.h" // ATmega2560 env:megaatmega2560 + #include "ramps/pins_FORMBOT_RAPTOR2.h" // ATmega2560 env:megaatmega2560 #elif MB(FORMBOT_TREX2PLUS) - #include "pins_FORMBOT_TREX2PLUS.h" // ATmega2560 env:megaatmega2560 + #include "ramps/pins_FORMBOT_TREX2PLUS.h" // ATmega2560 env:megaatmega2560 #elif MB(FORMBOT_TREX3) - #include "pins_FORMBOT_TREX3.h" // ATmega2560 env:megaatmega2560 + #include "ramps/pins_FORMBOT_TREX3.h" // ATmega2560 env:megaatmega2560 #elif MB(RUMBA) - #include "pins_RUMBA.h" // ATmega2560 env:megaatmega2560 + #include "ramps/pins_RUMBA.h" // ATmega2560 env:megaatmega2560 #elif MB(RUMBA_RAISE3D) - #include "pins_RUMBA_RAISE3D.h" // ATmega2560 env:megaatmega2560 + #include "ramps/pins_RUMBA_RAISE3D.h" // ATmega2560 env:megaatmega2560 #elif MB(RL200) - #include "pins_RL200.h" // ATmega2560 env:megaatmega2560 + #include "ramps/pins_RL200.h" // ATmega2560 env:megaatmega2560 #elif MB(BQ_ZUM_MEGA_3D) - #include "pins_BQ_ZUM_MEGA_3D.h" // ATmega2560 env:megaatmega2560 + #include "ramps/pins_BQ_ZUM_MEGA_3D.h" // ATmega2560 env:megaatmega2560 #elif MB(MAKEBOARD_MINI) - #include "pins_MAKEBOARD_MINI.h" // ATmega2560 env:megaatmega2560 + #include "ramps/pins_MAKEBOARD_MINI.h" // ATmega2560 env:megaatmega2560 #elif MB(TRIGORILLA_13) - #include "pins_TRIGORILLA_13.h" // ATmega2560 env:megaatmega2560 + #include "ramps/pins_TRIGORILLA_13.h" // ATmega2560 env:megaatmega2560 #elif MB(TRIGORILLA_14) - #include "pins_TRIGORILLA_14.h" // ATmega2560 env:megaatmega2560 + #include "ramps/pins_TRIGORILLA_14.h" // ATmega2560 env:megaatmega2560 #elif MB(TRIGORILLA_14_11) - #include "pins_TRIGORILLA_14.h" // ATmega2560 env:megaatmega2560 + #include "ramps/pins_TRIGORILLA_14.h" // ATmega2560 env:megaatmega2560 #elif MB(RAMPS_ENDER_4) - #include "pins_RAMPS_ENDER_4.h" // ATmega2560 env:megaatmega2560 + #include "ramps/pins_RAMPS_ENDER_4.h" // ATmega2560 env:megaatmega2560 #elif MB(RAMPS_CREALITY) - #include "pins_RAMPS_CREALITY.h" // ATmega2560 env:megaatmega2560 + #include "ramps/pins_RAMPS_CREALITY.h" // ATmega2560 env:megaatmega2560 #elif MB(RAMPS_DAGOMA) - #include "pins_RAMPS_DAGOMA.h" // ATmega2560 env:megaatmega2560 + #include "ramps/pins_RAMPS_DAGOMA.h" // ATmega2560 env:megaatmega2560 #elif MB(FYSETC_F6_13) - #include "pins_FYSETC_F6_13.h" // ATmega2560 env:fysetc_f6_13 + #include "ramps/pins_FYSETC_F6_13.h" // ATmega2560 env:fysetc_f6_13 #elif MB(DUPLICATOR_I3_PLUS) - #include "pins_DUPLICATOR_I3_PLUS.h" // ATmega2560 env:megaatmega2560 + #include "ramps/pins_DUPLICATOR_I3_PLUS.h" // ATmega2560 env:megaatmega2560 #elif MB(VORON) - #include "pins_VORON.h" // ATmega2560 env:megaatmega2560 + #include "ramps/pins_VORON.h" // ATmega2560 env:megaatmega2560 #elif MB(TRONXY_V3_1_0) - #include "pins_TRONXY_V3_1_0.h" // ATmega2560 env:megaatmega2560 + #include "ramps/pins_TRONXY_V3_1_0.h" // ATmega2560 env:megaatmega2560 #elif MB(Z_BOLT_X_SERIES) - #include "pins_Z_BOLT_X_SERIES.h" // ATmega2560 env:megaatmega2560 + #include "ramps/pins_Z_BOLT_X_SERIES.h" // ATmega2560 env:megaatmega2560 +#elif MB(TT_OSCAR) + #include "ramps/pins_TT_OSCAR.h" // ATmega2560 env:megaatmega2560 + +// +// RAMBo and derivatives +// + +#elif MB(RAMBO) + #include "rambo/pins_RAMBO.h" // ATmega2560 env:rambo +#elif MB(MINIRAMBO) || MB(MINIRAMBO_10A) + #include "rambo/pins_MINIRAMBO.h" // ATmega2560 env:rambo +#elif MB(EINSY_RAMBO) + #include "rambo/pins_EINSY_RAMBO.h" // ATmega2560 env:rambo +#elif MB(EINSY_RETRO) + #include "rambo/pins_EINSY_RETRO.h" // ATmega2560 env:rambo +#elif MB(SCOOVO_X9H) + #include "rambo/pins_SCOOVO_X9H.h" // ATmega2560 env:rambo // // Other ATmega1280, ATmega2560 // #elif MB(CNCONTROLS_11) - #include "pins_CNCONTROLS_11.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "mega/pins_CNCONTROLS_11.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(CNCONTROLS_12) - #include "pins_CNCONTROLS_12.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "mega/pins_CNCONTROLS_12.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(MIGHTYBOARD_REVE) - #include "pins_MIGHTYBOARD_REVE.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "mega/pins_MIGHTYBOARD_REVE.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(CHEAPTRONIC) - #include "pins_CHEAPTRONIC.h" // ATmega2560 env:megaatmega2560 + #include "mega/pins_CHEAPTRONIC.h" // ATmega2560 env:megaatmega2560 #elif MB(CHEAPTRONIC_V2) - #include "pins_CHEAPTRONICv2.h" // ATmega2560 env:megaatmega2560 + #include "mega/pins_CHEAPTRONICv2.h" // ATmega2560 env:megaatmega2560 #elif MB(MEGATRONICS) - #include "pins_MEGATRONICS.h" // ATmega2560 env:megaatmega2560 + #include "mega/pins_MEGATRONICS.h" // ATmega2560 env:megaatmega2560 #elif MB(MEGATRONICS_2) - #include "pins_MEGATRONICS_2.h" // ATmega2560 env:megaatmega2560 + #include "mega/pins_MEGATRONICS_2.h" // ATmega2560 env:megaatmega2560 #elif MB(MEGATRONICS_3) || MB(MEGATRONICS_31) || MB(MEGATRONICS_32) - #include "pins_MEGATRONICS_3.h" // ATmega2560 env:megaatmega2560 -#elif MB(RAMBO) - #include "pins_RAMBO.h" // ATmega2560 env:rambo -#elif MB(MINIRAMBO) || MB(MINIRAMBO_10A) - #include "pins_MINIRAMBO.h" // ATmega2560 env:rambo -#elif MB(EINSY_RAMBO) - #include "pins_EINSY_RAMBO.h" // ATmega2560 env:rambo -#elif MB(EINSY_RETRO) - #include "pins_EINSY_RETRO.h" // ATmega2560 env:rambo + #include "mega/pins_MEGATRONICS_3.h" // ATmega2560 env:megaatmega2560 #elif MB(ELEFU_3) - #include "pins_ELEFU_3.h" // ATmega2560 env:megaatmega2560 + #include "mega/pins_ELEFU_3.h" // ATmega2560 env:megaatmega2560 #elif MB(LEAPFROG) - #include "pins_LEAPFROG.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "mega/pins_LEAPFROG.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(MEGACONTROLLER) - #include "pins_MEGACONTROLLER.h" // ATmega2560 env:megaatmega2560 -#elif MB(SCOOVO_X9H) - #include "pins_SCOOVO_X9H.h" // ATmega2560 env:rambo + #include "mega/pins_MEGACONTROLLER.h" // ATmega2560 env:megaatmega2560 #elif MB(GT2560_REV_A) - #include "pins_GT2560_REV_A.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "mega/pins_GT2560_REV_A.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(GT2560_REV_A_PLUS) - #include "pins_GT2560_REV_A_PLUS.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "mega/pins_GT2560_REV_A_PLUS.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(GT2560_V3) - #include "pins_GT2560_V3.h" // ATmega2560 env:megaatmega2560 + #include "mega/pins_GT2560_V3.h" // ATmega2560 env:megaatmega2560 #elif MB(GT2560_V3_MC2) - #include "pins_GT2560_V3_MC2.h" // ATmega2560 env:megaatmega2560 + #include "mega/pins_GT2560_V3_MC2.h" // ATmega2560 env:megaatmega2560 #elif MB(GT2560_V3_A20) - #include "pins_GT2560_V3_A20.h" // ATmega2560 env:megaatmega2560 + #include "mega/pins_GT2560_V3_A20.h" // ATmega2560 env:megaatmega2560 #elif MB(EINSTART_S) - #include "pins_EINSTART-S.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 + #include "mega/pins_EINSTART-S.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 +#elif MB(WANHAO_ONEPLUS) + #include "mega/pins_WANHAO_ONEPLUS.h" // ATmega2560 env:megaatmega2560 +#elif MB(OVERLORD) + #include "mega/pins_OVERLORD.h" // ATmega2560 env:megaatmega2560 // // ATmega1281, ATmega2561 // #elif MB(MINITRONICS) - #include "pins_MINITRONICS.h" // ATmega1281 env:megaatmega1280 + #include "mega/pins_MINITRONICS.h" // ATmega1281 env:megaatmega1280 #elif MB(SILVER_GATE) - #include "pins_SILVER_GATE.h" // ATmega2561 env:megaatmega2560 + #include "mega/pins_SILVER_GATE.h" // ATmega2561 env:megaatmega2560 // // Sanguinololu and Derivatives - ATmega644P, ATmega1284P // #elif MB(SANGUINOLOLU_11) - #include "pins_SANGUINOLOLU_11.h" // ATmega644P, ATmega1284P env:sanguino_atmega644p env:sanguino_atmega1284p + #include "sanguino/pins_SANGUINOLOLU_11.h" // ATmega644P, ATmega1284P env:sanguino_atmega644p env:sanguino_atmega1284p #elif MB(SANGUINOLOLU_12) - #include "pins_SANGUINOLOLU_12.h" // ATmega644P, ATmega1284P env:sanguino_atmega644p env:sanguino_atmega1284p + #include "sanguino/pins_SANGUINOLOLU_12.h" // ATmega644P, ATmega1284P env:sanguino_atmega644p env:sanguino_atmega1284p #elif MB(MELZI) - #include "pins_MELZI.h" // ATmega644P, ATmega1284P env:sanguino_atmega644p env:sanguino_atmega1284p + #include "sanguino/pins_MELZI.h" // ATmega644P, ATmega1284P env:sanguino_atmega644p env:sanguino_atmega1284p #elif MB(MELZI_MAKR3D) - #include "pins_MELZI_MAKR3D.h" // ATmega644P, ATmega1284P env:sanguino_atmega644p env:sanguino_atmega1284p + #include "sanguino/pins_MELZI_MAKR3D.h" // ATmega644P, ATmega1284P env:sanguino_atmega644p env:sanguino_atmega1284p #elif MB(MELZI_CREALITY) - #include "pins_MELZI_CREALITY.h" // ATmega644P, ATmega1284P env:sanguino_atmega644p env:sanguino_atmega1284p + #include "sanguino/pins_MELZI_CREALITY.h" // ATmega644P, ATmega1284P env:sanguino_atmega644p env:sanguino_atmega1284p #elif MB(MELZI_MALYAN) - #include "pins_MELZI_MALYAN.h" // ATmega644P, ATmega1284P env:sanguino_atmega644p env:sanguino_atmega1284p + #include "sanguino/pins_MELZI_MALYAN.h" // ATmega644P, ATmega1284P env:sanguino_atmega644p env:sanguino_atmega1284p #elif MB(MELZI_TRONXY) - #include "pins_MELZI_TRONXY.h" // ATmega644P, ATmega1284P env:sanguino_atmega644p env:sanguino_atmega1284p + #include "sanguino/pins_MELZI_TRONXY.h" // ATmega644P, ATmega1284P env:sanguino_atmega644p env:sanguino_atmega1284p #elif MB(STB_11) - #include "pins_STB_11.h" // ATmega644P, ATmega1284P env:sanguino_atmega644p env:sanguino_atmega1284p + #include "sanguino/pins_STB_11.h" // ATmega644P, ATmega1284P env:sanguino_atmega644p env:sanguino_atmega1284p #elif MB(AZTEEG_X1) - #include "pins_AZTEEG_X1.h" // ATmega644P, ATmega1284P env:sanguino_atmega644p env:sanguino_atmega1284p + #include "sanguino/pins_AZTEEG_X1.h" // ATmega644P, ATmega1284P env:sanguino_atmega644p env:sanguino_atmega1284p // // Other ATmega644P, ATmega644, ATmega1284P // #elif MB(GEN3_MONOLITHIC) - #include "pins_GEN3_MONOLITHIC.h" // ATmega644P env:sanguino_atmega644p + #include "sanguino/pins_GEN3_MONOLITHIC.h" // ATmega644P env:sanguino_atmega644p #elif MB(GEN3_PLUS) - #include "pins_GEN3_PLUS.h" // ATmega644P, ATmega1284P env:sanguino_atmega644p env:sanguino_atmega1284p + #include "sanguino/pins_GEN3_PLUS.h" // ATmega644P, ATmega1284P env:sanguino_atmega644p env:sanguino_atmega1284p #elif MB(GEN6) - #include "pins_GEN6.h" // ATmega644P, ATmega1284P env:sanguino_atmega644p env:sanguino_atmega1284p + #include "sanguino/pins_GEN6.h" // ATmega644P, ATmega1284P env:sanguino_atmega644p env:sanguino_atmega1284p #elif MB(GEN6_DELUXE) - #include "pins_GEN6_DELUXE.h" // ATmega644P, ATmega1284P env:sanguino_atmega644p env:sanguino_atmega1284p + #include "sanguino/pins_GEN6_DELUXE.h" // ATmega644P, ATmega1284P env:sanguino_atmega644p env:sanguino_atmega1284p #elif MB(GEN7_CUSTOM) - #include "pins_GEN7_CUSTOM.h" // ATmega644P, ATmega644, ATmega1284P env:sanguino_atmega644p env:sanguino_atmega1284p + #include "sanguino/pins_GEN7_CUSTOM.h" // ATmega644P, ATmega644, ATmega1284P env:sanguino_atmega644p env:sanguino_atmega1284p #elif MB(GEN7_12) - #include "pins_GEN7_12.h" // ATmega644P, ATmega644, ATmega1284P env:sanguino_atmega644p env:sanguino_atmega1284p + #include "sanguino/pins_GEN7_12.h" // ATmega644P, ATmega644, ATmega1284P env:sanguino_atmega644p env:sanguino_atmega1284p #elif MB(GEN7_13) - #include "pins_GEN7_13.h" // ATmega644P, ATmega644, ATmega1284P env:sanguino_atmega644p env:sanguino_atmega1284p + #include "sanguino/pins_GEN7_13.h" // ATmega644P, ATmega644, ATmega1284P env:sanguino_atmega644p env:sanguino_atmega1284p #elif MB(GEN7_14) - #include "pins_GEN7_14.h" // ATmega644P, ATmega644, ATmega1284P env:sanguino_atmega644p env:sanguino_atmega1284p + #include "sanguino/pins_GEN7_14.h" // ATmega644P, ATmega644, ATmega1284P env:sanguino_atmega644p env:sanguino_atmega1284p #elif MB(OMCA_A) - #include "pins_OMCA_A.h" // ATmega644 env:sanguino_atmega644p + #include "sanguino/pins_OMCA_A.h" // ATmega644 env:sanguino_atmega644p #elif MB(OMCA) - #include "pins_OMCA.h" // ATmega644P, ATmega644 env:sanguino_atmega644p + #include "sanguino/pins_OMCA.h" // ATmega644P, ATmega644 env:sanguino_atmega644p #elif MB(ANET_10) - #include "pins_ANET_10.h" // ATmega1284P env:sanguino_atmega1284p + #include "sanguino/pins_ANET_10.h" // ATmega1284P env:sanguino_atmega1284p #elif MB(SETHI) - #include "pins_SETHI.h" // ATmega644P, ATmega644, ATmega1284P env:sanguino_atmega644p env:sanguino_atmega1284p + #include "sanguino/pins_SETHI.h" // ATmega644P, ATmega644, ATmega1284P env:sanguino_atmega644p env:sanguino_atmega1284p // // Teensyduino - AT90USB1286, AT90USB1286P // #elif MB(TEENSYLU) - #include "pins_TEENSYLU.h" // AT90USB1286, AT90USB1286P env:at90usb1286_cdc + #include "teensy2/pins_TEENSYLU.h" // AT90USB1286, AT90USB1286P env:at90usb1286_cdc #elif MB(PRINTRBOARD) - #include "pins_PRINTRBOARD.h" // AT90USB1286 env:at90usb1286_dfu + #include "teensy2/pins_PRINTRBOARD.h" // AT90USB1286 env:at90usb1286_dfu #elif MB(PRINTRBOARD_REVF) - #include "pins_PRINTRBOARD_REVF.h" // AT90USB1286 env:at90usb1286_dfu + #include "teensy2/pins_PRINTRBOARD_REVF.h" // AT90USB1286 env:at90usb1286_dfu #elif MB(BRAINWAVE) - #include "pins_BRAINWAVE.h" // AT90USB646 env:at90usb1286_cdc + #include "teensy2/pins_BRAINWAVE.h" // AT90USB646 env:at90usb1286_cdc #elif MB(BRAINWAVE_PRO) - #include "pins_BRAINWAVE_PRO.h" // AT90USB1286 env:at90usb1286_cdc + #include "teensy2/pins_BRAINWAVE_PRO.h" // AT90USB1286 env:at90usb1286_cdc #elif MB(SAV_MKI) - #include "pins_SAV_MKI.h" // AT90USB1286 env:at90usb1286_cdc + #include "teensy2/pins_SAV_MKI.h" // AT90USB1286 env:at90usb1286_cdc #elif MB(TEENSY2) - #include "pins_TEENSY2.h" // AT90USB1286 env:teensy20 + #include "teensy2/pins_TEENSY2.h" // AT90USB1286 env:teensy20 #elif MB(5DPRINT) - #include "pins_5DPRINT.h" // AT90USB1286 env:at90usb1286_dfu + #include "teensy2/pins_5DPRINT.h" // AT90USB1286 env:at90usb1286_dfu // // LPC1768 ARM Cortex M3 // #elif MB(RAMPS_14_RE_ARM_EFB) - #include "pins_RAMPS_RE_ARM.h" // LPC1768 env:LPC1768 + #include "lpc1768/pins_RAMPS_RE_ARM.h" // LPC1768 env:LPC1768 #elif MB(RAMPS_14_RE_ARM_EEB) - #include "pins_RAMPS_RE_ARM.h" // LPC1768 env:LPC1768 + #include "lpc1768/pins_RAMPS_RE_ARM.h" // LPC1768 env:LPC1768 #elif MB(RAMPS_14_RE_ARM_EFF) - #include "pins_RAMPS_RE_ARM.h" // LPC1768 env:LPC1768 + #include "lpc1768/pins_RAMPS_RE_ARM.h" // LPC1768 env:LPC1768 #elif MB(RAMPS_14_RE_ARM_EEF) - #include "pins_RAMPS_RE_ARM.h" // LPC1768 env:LPC1768 + #include "lpc1768/pins_RAMPS_RE_ARM.h" // LPC1768 env:LPC1768 #elif MB(RAMPS_14_RE_ARM_SF) - #include "pins_RAMPS_RE_ARM.h" // LPC1768 env:LPC1768 + #include "lpc1768/pins_RAMPS_RE_ARM.h" // LPC1768 env:LPC1768 #elif MB(MKS_SBASE) - #include "pins_MKS_SBASE.h" // LPC1768 env:LPC1768 -#elif MB(MKS_SGEN) - #include "pins_MKS_SGEN.h" // LPC1769 env:LPC1769 + #include "lpc1768/pins_MKS_SBASE.h" // LPC1768 env:LPC1768 #elif MB(MKS_SGEN_L) - #include "pins_MKS_SGEN_L.h" // LPC1768 env:LPC1768 + #include "lpc1768/pins_MKS_SGEN_L.h" // LPC1768 env:LPC1768 #elif MB(AZSMZ_MINI) - #include "pins_AZSMZ_MINI.h" // LPC1768 env:LPC1768 -#elif MB(AZTEEG_X5_GT) - #include "pins_AZTEEG_X5_GT.h" // LPC1769 env:LPC1769 -#elif MB(AZTEEG_X5_MINI) - #include "pins_AZTEEG_X5_MINI.h" // LPC1769 env:LPC1769 -#elif MB(AZTEEG_X5_MINI_WIFI) - #include "pins_AZTEEG_X5_MINI_WIFI.h" // LPC1769 env:LPC1769 + #include "lpc1768/pins_AZSMZ_MINI.h" // LPC1768 env:LPC1768 #elif MB(BIQU_BQ111_A4) - #include "pins_BIQU_BQ111_A4.h" // LPC1768 env:LPC1768 + #include "lpc1768/pins_BIQU_BQ111_A4.h" // LPC1768 env:LPC1768 #elif MB(SELENA_COMPACT) - #include "pins_SELENA_COMPACT.h" // LPC1768 env:LPC1768 -#elif MB(COHESION3D_REMIX) - #include "pins_COHESION3D_REMIX.h" // LPC1769 env:LPC1769 -#elif MB(COHESION3D_MINI) - #include "pins_COHESION3D_MINI.h" // LPC1769 env:LPC1769 -#elif MB(SMOOTHIEBOARD) - #include "pins_SMOOTHIEBOARD.h" // LPC1769 env:LPC1769 -#elif MB(BIQU_SKR_V1_1) - #include "pins_BIQU_SKR_V1.1.h" // LPC1768 env:LPC1768 + #include "lpc1768/pins_SELENA_COMPACT.h" // LPC1768 env:LPC1768 +#elif MB(BIGTREE_SKR_V1_1) + #include "lpc1768/pins_BIGTREE_SKR_V1.1.h" // LPC1768 env:LPC1768 #elif MB(BIQU_B300_V1_0) - #include "pins_BIQU_B300_V1.0.h" // LPC1768 env:LPC1768 + #include "lpc1768/pins_BIQU_B300_V1.0.h" // LPC1768 env:LPC1768 #elif MB(BIGTREE_SKR_V1_3) - #include "pins_BIGTREE_SKR_V1.3.h" // LPC1768 env:LPC1768 + #include "lpc1768/pins_BIGTREE_SKR_V1.3.h" // LPC1768 env:LPC1768 #elif MB(TH3D_EZBOARD) - #include "pins_TH3D_EZBOARD.h" // LPC1768 env:LPC1768 + #include "lpc1768/pins_TH3D_EZBOARD.h" // LPC1768 env:LPC1768 +#elif MB(GMARSH_X6_REV1) + #include "lpc1768/pins_GMARSH_X6_REV1.h" // LPC1768 env:LPC1768 // -// Other 32-bit Boards +// LPC1769 ARM Cortex M3 +// + +#elif MB(MKS_SGEN) + #include "lpc1769/pins_MKS_SGEN.h" // LPC1769 env:LPC1769 +#elif MB(AZTEEG_X5_GT) + #include "lpc1769/pins_AZTEEG_X5_GT.h" // LPC1769 env:LPC1769 +#elif MB(AZTEEG_X5_MINI) + #include "lpc1769/pins_AZTEEG_X5_MINI.h" // LPC1769 env:LPC1769 +#elif MB(AZTEEG_X5_MINI_WIFI) + #include "lpc1769/pins_AZTEEG_X5_MINI_WIFI.h" // LPC1769 env:LPC1769 +#elif MB(COHESION3D_REMIX) + #include "lpc1769/pins_COHESION3D_REMIX.h" // LPC1769 env:LPC1769 +#elif MB(COHESION3D_MINI) + #include "lpc1769/pins_COHESION3D_MINI.h" // LPC1769 env:LPC1769 +#elif MB(SMOOTHIEBOARD) + #include "lpc1769/pins_SMOOTHIEBOARD.h" // LPC1769 env:LPC1769 + +// +// Due (ATSAM) boards // #elif MB(DUE3DOM) - #include "pins_DUE3DOM.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug + #include "sam/pins_DUE3DOM.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug #elif MB(DUE3DOM_MINI) - #include "pins_DUE3DOM_MINI.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug + #include "sam/pins_DUE3DOM_MINI.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug #elif MB(RADDS) - #include "pins_RADDS.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug + #include "sam/pins_RADDS.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug #elif MB(RURAMPS4D_11) - #include "pins_RURAMPS4D_11.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug + #include "sam/pins_RURAMPS4D_11.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug #elif MB(RURAMPS4D_13) - #include "pins_RURAMPS4D_13.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug + #include "sam/pins_RURAMPS4D_13.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug #elif MB(RAMPS_FD_V1) - #include "pins_RAMPS_FD_V1.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug + #include "sam/pins_RAMPS_FD_V1.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug #elif MB(RAMPS_FD_V2) - #include "pins_RAMPS_FD_V2.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug + #include "sam/pins_RAMPS_FD_V2.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug #elif MB(RAMPS_SMART_EFB) - #include "pins_RAMPS_SMART.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug + #include "sam/pins_RAMPS_SMART.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug #elif MB(RAMPS_SMART_EEB) - #include "pins_RAMPS_SMART.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug + #include "sam/pins_RAMPS_SMART.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug #elif MB(RAMPS_SMART_EFF) - #include "pins_RAMPS_SMART.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug + #include "sam/pins_RAMPS_SMART.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug #elif MB(RAMPS_SMART_EEF) - #include "pins_RAMPS_SMART.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug + #include "sam/pins_RAMPS_SMART.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug #elif MB(RAMPS_SMART_SF) - #include "pins_RAMPS_SMART.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug + #include "sam/pins_RAMPS_SMART.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug #elif MB(RAMPS_DUO_EFB) - #include "pins_RAMPS_DUO.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug + #include "sam/pins_RAMPS_DUO.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug #elif MB(RAMPS_DUO_EEB) - #include "pins_RAMPS_DUO.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug + #include "sam/pins_RAMPS_DUO.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug #elif MB(RAMPS_DUO_EFF) - #include "pins_RAMPS_DUO.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug + #include "sam/pins_RAMPS_DUO.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug #elif MB(RAMPS_DUO_EEF) - #include "pins_RAMPS_DUO.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug + #include "sam/pins_RAMPS_DUO.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug #elif MB(RAMPS_DUO_SF) - #include "pins_RAMPS_DUO.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug + #include "sam/pins_RAMPS_DUO.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug #elif MB(RAMPS4DUE_EFB) - #include "pins_RAMPS4DUE.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug + #include "sam/pins_RAMPS4DUE.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug #elif MB(RAMPS4DUE_EEB) - #include "pins_RAMPS4DUE.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug + #include "sam/pins_RAMPS4DUE.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug #elif MB(RAMPS4DUE_EFF) - #include "pins_RAMPS4DUE.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug + #include "sam/pins_RAMPS4DUE.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug #elif MB(RAMPS4DUE_EEF) - #include "pins_RAMPS4DUE.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug + #include "sam/pins_RAMPS4DUE.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug #elif MB(RAMPS4DUE_SF) - #include "pins_RAMPS4DUE.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug + #include "sam/pins_RAMPS4DUE.h" // SAM3X8E env:DUE env:DUE_USB env:DUE_debug #elif MB(ULTRATRONICS_PRO) - #include "pins_ULTRATRONICS_PRO.h" // SAM3X8E env:DUE env:DUE_debug + #include "sam/pins_ULTRATRONICS_PRO.h" // SAM3X8E env:DUE env:DUE_debug #elif MB(ARCHIM1) - #include "pins_ARCHIM1.h" // SAM3X8E env:DUE env:DUE_debug + #include "sam/pins_ARCHIM1.h" // SAM3X8E env:DUE env:DUE_debug #elif MB(ARCHIM2) - #include "pins_ARCHIM2.h" // SAM3X8E env:DUE env:DUE_debug + #include "sam/pins_ARCHIM2.h" // SAM3X8E env:DUE env:DUE_debug #elif MB(ALLIGATOR) - #include "pins_ALLIGATOR_R2.h" // SAM3X8E env:DUE env:DUE_debug + #include "sam/pins_ALLIGATOR_R2.h" // SAM3X8E env:DUE env:DUE_debug #elif MB(ADSK) - #include "pins_ADSK.h" // SAM3X8E env:DUE env:DUE_debug + #include "sam/pins_ADSK.h" // SAM3X8E env:DUE env:DUE_debug #elif MB(PRINTRBOARD_G2) - #include "pins_PRINTRBOARD_G2.h" // SAM3X8C env:DUE_USB + #include "sam/pins_PRINTRBOARD_G2.h" // SAM3X8C env:DUE_USB // // STM32 ARM Cortex-M3 // #elif MB(STM32F1R) - #include "pins_STM32F1R.h" // STM32F1 env:STM32F1 -#elif MB(STM3R_MINI) - #include "pins_STM3R_MINI.h" // STM32F1 env:STM32F1 -#elif MB(BIGTREE_SKR_MINI_V1_1) - #include "pins_BIGTREE_SKR_MINI_V1_1.h" // STM32F1 env:BIGTREE_SKR_MINI -#elif MB(BIGTREE_SKR_MINI_E3) - #include "pins_BIGTREE_SKR_MINI_E3.h" // STM32F1 env:BIGTREE_SKR_MINI + #include "stm32/pins_STM32F1R.h" // STM32F1 env:STM32F1 #elif MB(MALYAN_M200) - #include "pins_MALYAN_M200.h" // STM32F1 env:malyanm200 -#elif MB(CHITU3D) - #include "pins_CHITU3D.h" // STM32F1 env:STM32F1 + #include "stm32/pins_MALYAN_M200.h" // STM32F1 env:malyanm200 +#elif MB(STM3R_MINI) + #include "stm32/pins_STM3R_MINI.h" // STM32F1 env:STM32F1 #elif MB(GTM32_PRO_VB) - #include "pins_GTM32_PRO_VB.h" // STM32F1 env:STM32F1 + #include "stm32/pins_GTM32_PRO_VB.h" // STM32F1 env:STM32F1 #elif MB(MORPHEUS) - #include "pins_MORPHEUS.h" // STM32F1 env:STM32F1 + #include "stm32/pins_MORPHEUS.h" // STM32F1 env:STM32F1 +#elif MB(CHITU3D) + #include "stm32/pins_CHITU3D.h" // STM32F1 env:STM32F1 #elif MB(MKS_ROBIN) - #include "pins_MKS_ROBIN.h" // STM32F1 env:mks_robin + #include "stm32/pins_MKS_ROBIN.h" // STM32F1 env:mks_robin #elif MB(MKS_ROBIN_MINI) - #include "pins_MKS_ROBIN_MINI.h" // STM32F1 env:mks_robin_mini + #include "stm32/pins_MKS_ROBIN_MINI.h" // STM32F1 env:mks_robin_mini #elif MB(MKS_ROBIN_NANO) - #include "pins_MKS_ROBIN_NANO.h" // STM32F1 env:mks_robin_nano + #include "stm32/pins_MKS_ROBIN_NANO.h" // STM32F1 env:mks_robin_nano +#elif MB(MKS_ROBIN_LITE) + #include "stm32/pins_MKS_ROBIN_LITE.h" // STM32F1 env:mks_robin_lite +#elif MB(BIGTREE_SKR_MINI_V1_1) + #include "stm32/pins_BIGTREE_SKR_MINI_V1_1.h" // STM32F1 env:BIGTREE_SKR_MINI +#elif MB(BIGTREE_SKR_MINI_E3) + #include "stm32/pins_BIGTREE_SKR_MINI_E3.h" // STM32F1 env:BIGTREE_SKR_MINI +#elif MB(BIGTREE_SKR_E3_DIP) + #include "stm32/pins_BIGTREE_SKR_E3_DIP.h" // STM32F1 env:BIGTREE_SKR_MINI #elif MB(JGAURORA_A5S_A1) - #include "pins_JGAURORA_A5S_A1.h" // STM32F1 env:JGAURORA_A5S_A1 + #include "stm32/pins_JGAURORA_A5S_A1.h" // STM32F1 env:jgaurora_a5s_a1 #elif MB(FYSETC_AIO_II) - #include "pins_FYSETC_AIO_II.h" // STM32F1 env:fysetc_STM32F1 + #include "stm32/pins_FYSETC_AIO_II.h" // STM32F1 env:fysetc_STM32F1 #elif MB(FYSETC_CHEETAH) - #include "pins_FYSETC_CHEETAH.h" // STM32F1 env:fysetc_STM32F1 + #include "stm32/pins_FYSETC_CHEETAH.h" // STM32F1 env:fysetc_STM32F1 +#elif MB(FYSETC_CHEETAH_V12) + #include "stm32/pins_FYSETC_CHEETAH_V12.h" // STM32F1 env:fysetc_STM32F1 +#elif MB(LONGER3D_LK) + #include "stm32/pins_LONGER3D_LK.h" // STM32F1 env:alfawise_U20 + +// +// ARM Cortex-M4F +// + +#elif MB(TEENSY31_32) + #include "teensy3/pins_TEENSY31_32.h" // TEENSY31_32 env:teensy31 +#elif MB(TEENSY35_36) + #include "teensy3/pins_TEENSY35_36.h" // TEENSY35_36 env:teensy35 // // STM32 ARM Cortex-M4F // -#elif MB(TEENSY31_32) - #include "pins_TEENSY31_32.h" // TEENSY31_32 env:teensy31 -#elif MB(TEENSY35_36) - #include "pins_TEENSY35_36.h" // TEENSY35_36 env:teensy35 #elif MB(BEAST) - #include "pins_BEAST.h" // STM32F4 env:STM32F4 + #include "stm32/pins_BEAST.h" // STM32F4 env:STM32F4 #elif MB(STM32F4) - #include "pins_STM32F4.h" // STM32F4 env:STM32F4 + #include "stm32/pins_STM32F4.h" // STM32F4 env:STM32F4 #elif MB(ARMED) - #include "pins_ARMED.h" // STM32F4 env:ARMED + #include "stm32/pins_ARMED.h" // STM32F4 env:ARMED #elif MB(RUMBA32) - #include "pins_RUMBA32.h" // STM32F4 env:RUMBA32 + #include "stm32/pins_RUMBA32.h" // STM32F4 env:RUMBA32 #elif MB(BLACK_STM32F407VE) - #include "pins_BLACK_STM32F407VE.h" // STM32F4 env:black_stm32f407ve + #include "stm32/pins_BLACK_STM32F407VE.h" // STM32F4 env:black_stm32f407ve #elif MB(STEVAL) - #include "pins_STEVAL.h" // STM32F4 env:STM32F4 + #include "stm32/pins_STEVAL.h" // STM32F4 env:STM32F4 +#elif MB(BIGTREE_SKR_PRO_V1_1) + #include "stm32/pins_BIGTREE_SKR_PRO_V1.1.h" // STM32F4 env:BIGTREE_SKR_PRO // // ARM Cortex M7 // #elif MB(THE_BORG) - #include "pins_THE_BORG.h" // STM32F7 env:STM32F7 + #include "stm32/pins_THE_BORG.h" // STM32F7 env:STM32F7 #elif MB(REMRAM_V1) - #include "pins_REMRAM_V1.h" // STM32F7 env:STM32F7xx + #include "stm32/pins_REMRAM_V1.h" // STM32F7 env:STM32F7xx // // Espressif ESP32 // #elif MB(ESP32) - #include "pins_ESP32.h" // ESP32 env:esp32 + #include "esp32/pins_ESP32.h" // ESP32 env:esp32 + +// +// Adafruit Grand Central M4 (SAMD51 ARM Cortex-M4) +// + +#elif MB(AGCM4_RURAMPS4D_13) + #include "samd/pins_AGCM4_RURAMPS4D_13.h" // SAMD51 env:adafruit_grandcentral_m4 // // Linux Native Debug board // #elif MB(LINUX_RAMPS) - #include "pins_RAMPS_LINUX.h" // Linux env:linux_native + #include "linux/pins_RAMPS_LINUX.h" // Linux env:linux_native #else #error "Unknown MOTHERBOARD value set in Configuration.h" @@ -732,8 +774,8 @@ #ifndef SD_DETECT_PIN #define SD_DETECT_PIN -1 #endif -#ifndef SDPOWER - #define SDPOWER -1 +#ifndef SDPOWER_PIN + #define SDPOWER_PIN -1 #endif #ifndef SDSS #define SDSS -1 @@ -945,6 +987,14 @@ #ifndef X2_MS3_PIN #define X2_MS3_PIN _EPIN(E_STEPPERS, MS3) #endif + #if AXIS_DRIVER_TYPE_X2(TMC2208) || AXIS_DRIVER_TYPE_X2(TMC2209) + #ifndef X2_SERIAL_TX_PIN + #define X2_SERIAL_TX_PIN _EPIN(E_STEPPERS, SERIAL_TX) + #endif + #ifndef X2_SERIAL_RX_PIN + #define X2_SERIAL_RX_PIN _EPIN(E_STEPPERS, SERIAL_RX) + #endif + #endif #define Y2_E_INDEX INCREMENT(E_STEPPERS) #else #define Y2_E_INDEX E_STEPPERS @@ -972,6 +1022,14 @@ #ifndef Y2_MS3_PIN #define Y2_MS3_PIN _EPIN(Y2_E_INDEX, MS3) #endif + #if AXIS_DRIVER_TYPE_Y2(TMC2208) || AXIS_DRIVER_TYPE_Y2(TMC2209) + #ifndef Y2_SERIAL_TX_PIN + #define Y2_SERIAL_TX_PIN _EPIN(Y2_E_INDEX, SERIAL_TX) + #endif + #ifndef Y2_SERIAL_RX_PIN + #define Y2_SERIAL_RX_PIN _EPIN(Y2_E_INDEX, SERIAL_RX) + #endif + #endif #define Z2_E_INDEX INCREMENT(Y2_E_INDEX) #else #define Z2_E_INDEX Y2_E_INDEX @@ -999,6 +1057,14 @@ #ifndef Z2_MS3_PIN #define Z2_MS3_PIN _EPIN(Z2_E_INDEX, MS3) #endif + #if AXIS_DRIVER_TYPE_Z2(TMC2208) || AXIS_DRIVER_TYPE_Z2(TMC2209) + #ifndef Z2_SERIAL_TX_PIN + #define Z2_SERIAL_TX_PIN _EPIN(Z2_E_INDEX, SERIAL_TX) + #endif + #ifndef Z2_SERIAL_RX_PIN + #define Z2_SERIAL_RX_PIN _EPIN(Z2_E_INDEX, SERIAL_RX) + #endif + #endif #define Z3_E_INDEX INCREMENT(Z2_E_INDEX) #else #define Z3_E_INDEX Z2_E_INDEX @@ -1025,4 +1091,14 @@ #ifndef Z3_MS3_PIN #define Z3_MS3_PIN _EPIN(Z3_E_INDEX, MS3) #endif + #if AXIS_DRIVER_TYPE_Z3(TMC2208) || AXIS_DRIVER_TYPE_Z3(TMC2209) + #ifndef Z3_SERIAL_TX_PIN + #define Z3_SERIAL_TX_PIN _EPIN(Z3_E_INDEX, SERIAL_TX) + #endif + #ifndef Z3_SERIAL_RX_PIN + #define Z3_SERIAL_RX_PIN _EPIN(Z3_E_INDEX, SERIAL_RX) + #endif + #endif #endif + +#undef HAS_FREE_AUX2_PINS diff --git a/Marlin/src/pins/pinsDebug.h b/Marlin/src/pins/pinsDebug.h index 37a2e86812..0421907771 100644 --- a/Marlin/src/pins/pinsDebug.h +++ b/Marlin/src/pins/pinsDebug.h @@ -17,6 +17,8 @@ * */ +#include "../inc/MarlinConfig.h" + #define MAX_NAME_LENGTH 39 // one place to specify the format of all the sources of names // "-" left justify, "39" minimum width of name, pad with blanks @@ -40,7 +42,7 @@ #define REPORT_NAME_ANALOG(COUNTER, NAME) _ADD_PIN(#NAME, COUNTER) #include "pinsDebug_list.h" -#line 47 +#line 46 // manually add pins that have names that are macros which don't play well with these macros #if SERIAL_PORT == 0 && (AVR_ATmega2560_FAMILY || AVR_ATmega1284_FAMILY || defined(ARDUINO_ARCH_SAM)) @@ -92,11 +94,10 @@ const PinInfo pin_array[] PROGMEM = { #endif #include "pinsDebug_list.h" - #line 99 + #line 98 }; - #include HAL_PATH(../HAL, pinsDebug.h) // get the correct support file for this CPU #ifndef M43_NEVER_TOUCH @@ -116,12 +117,12 @@ inline void report_pin_state_extended(pin_t pin, bool ignore, bool extended = fa if (GET_ARRAY_PIN(x) == pin) { if (found) multi_name_pin = true; found = true; - if (!multi_name_pin) { // report digitial and analog pin number only on the first time through + if (!multi_name_pin) { // report digital and analog pin number only on the first time through sprintf_P(buffer, PSTR("%sPIN: "), start_string); // digital pin number SERIAL_ECHO(buffer); PRINT_PIN(pin); PRINT_PORT(pin); - if (IS_ANALOG(pin)) { + if (int8_t(DIGITAL_PIN_TO_ANALOG_PIN(pin)) >= 0) { sprintf_P(buffer, PSTR(" (A%2d) "), DIGITAL_PIN_TO_ANALOG_PIN(pin)); // analog pin number SERIAL_ECHO(buffer); } @@ -183,7 +184,7 @@ inline void report_pin_state_extended(pin_t pin, bool ignore, bool extended = fa SERIAL_ECHO(buffer); PRINT_PIN(pin); PRINT_PORT(pin); - if (IS_ANALOG(pin)) { + if (int8_t(DIGITAL_PIN_TO_ANALOG_PIN(pin)) >= 0) { sprintf_P(buffer, PSTR(" (A%2d) "), DIGITAL_PIN_TO_ANALOG_PIN(pin)); // analog pin number SERIAL_ECHO(buffer); } @@ -206,7 +207,10 @@ inline void report_pin_state_extended(pin_t pin, bool ignore, bool extended = fa else #endif { - if (GET_PINMODE(pin)) { + if (pwm_status(pin)) { + // do nothing + } + else if (GET_PINMODE(pin)) { SERIAL_ECHO_SP(MAX_NAME_LENGTH - 16); print_input_or_output(true); SERIAL_ECHO(digitalRead_mod(pin)); @@ -224,7 +228,10 @@ inline void report_pin_state_extended(pin_t pin, bool ignore, bool extended = fa SERIAL_ECHO(digitalRead_mod(pin)); } //if (!pwm_status(pin)) SERIAL_CHAR(' '); // add padding if it's not a PWM pin - if (extended) pwm_details(pin); // report PWM capabilities only if doing an extended report + if (extended) { + SERIAL_ECHO_SP(MAX_NAME_LENGTH - 16); + pwm_details(pin); // report PWM capabilities only if doing an extended report + } } } SERIAL_EOL(); diff --git a/Marlin/src/pins/pinsDebug_list.h b/Marlin/src/pins/pinsDebug_list.h index cf6dcc098f..1bbc926e23 100644 --- a/Marlin/src/pins/pinsDebug_list.h +++ b/Marlin/src/pins/pinsDebug_list.h @@ -24,7 +24,7 @@ // Pin lists 1.1.x and 2.0.x synchronized 2018-02-17 -#line 31 // set __LINE__ to a known value for both passes +#line 28 // set __LINE__ to a known value for both passes // // Analog Pin Assignments @@ -51,7 +51,7 @@ #if PIN_EXISTS(MAIN_VOLTAGE_MEASURE) && MAIN_VOLTAGE_MEASURE_PIN < NUM_ANALOG_INPUTS REPORT_NAME_ANALOG(__LINE__, MAIN_VOLTAGE_MEASURE_PIN) #endif -#if !defined(ARDUINO_ARCH_SAM) //TC1 & TC2 are macros in the SAM tool chain +#if !defined(ARDUINO_ARCH_SAM) && !defined(ARDUINO_ARCH_SAMD) //TC1 & TC2 are macros in the SAM/SAMD tool chain #if defined(TC1) && TC1 >= 0 && TC1 < NUM_ANALOG_INPUTS REPORT_NAME_ANALOG(__LINE__, TC1) #endif @@ -707,8 +707,8 @@ // #if defined(SDA) && SDA >= 0 // REPORT_NAME_DIGITAL(__LINE__, SDA) // #endif -#if defined(SDPOWER) && SDPOWER >= 0 - REPORT_NAME_DIGITAL(__LINE__, SDPOWER) +#if PIN_EXISTS(SDPOWER) + REPORT_NAME_DIGITAL(__LINE__, SDPOWER_PIN) #endif #if defined(SDSS) && SDSS >= 0 REPORT_NAME_DIGITAL(__LINE__, SDSS) @@ -1160,3 +1160,18 @@ #if PIN_EXISTS(FET_SAFETY) REPORT_NAME_DIGITAL(__LINE__, FET_SAFETY_PIN) #endif +#if PIN_EXISTS(TOUCH_MISO) + REPORT_NAME_DIGITAL(__LINE__, TOUCH_MISO_PIN) +#endif +#if PIN_EXISTS(TOUCH_MOSI) + REPORT_NAME_DIGITAL(__LINE__, TOUCH_MOSI_PIN) +#endif +#if PIN_EXISTS(TOUCH_SCK) + REPORT_NAME_DIGITAL(__LINE__, TOUCH_SCK_PIN) +#endif +#if PIN_EXISTS(TOUCH_CS) + REPORT_NAME_DIGITAL(__LINE__, TOUCH_CS_PIN) +#endif +#if PIN_EXISTS(TOUCH_INT) + REPORT_NAME_DIGITAL(__LINE__, TOUCH_INT_PIN) +#endif diff --git a/Marlin/src/pins/pins_GTM32_PRO_VB.h b/Marlin/src/pins/pins_GTM32_PRO_VB.h deleted file mode 100644 index 87b32bf38a..0000000000 --- a/Marlin/src/pins/pins_GTM32_PRO_VB.h +++ /dev/null @@ -1,195 +0,0 @@ -/** - * Marlin 3D Printer Firmware - * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] - * - * Based on Sprinter and grbl. - * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm - * - * This program is free software: you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation, either version 3 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program. If not, see . - * - */ -#pragma once - -/** - * 24 May 2018 - @chepo for STM32F103VET6 - * Schematic: https://github.com/chepo92/Smartto/blob/master/circuit_diagram/Rostock301/Hardware_GTM32_PRO_VB.pdf - */ - -#ifndef __STM32F1__ - #error "Oops! Select an STM32F1 board in 'Tools > Board.'" -#endif - -#define DEFAULT_MACHINE_NAME "STM32F103VET6" -#define BOARD_NAME "GTM32 Pro VB" - -//#define DISABLE_DEBUG -#define DISABLE_JTAG -//#define DISABLE_JTAGSWD - -// Ignore temp readings during development. -#define BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE - -// -// Limit Switches -// -#define X_MIN_PIN PE5 -#define X_MAX_PIN PE4 -#define Y_MIN_PIN PE3 -#define Y_MAX_PIN PE2 -#define Z_MIN_PIN PE1 -#define Z_MAX_PIN PE0 - -// -// Steppers -// -#define X_STEP_PIN PC6 -#define X_DIR_PIN PD13 -#define X_ENABLE_PIN PA8 - -#define Y_STEP_PIN PA12 -#define Y_DIR_PIN PA11 -#define Y_ENABLE_PIN PA15 - -#define Z_STEP_PIN PD6 -#define Z_DIR_PIN PD3 -#define Z_ENABLE_PIN PB3 - -#define E0_STEP_PIN PB2 -#define E0_DIR_PIN PB11 -#define E0_ENABLE_PIN PC4 - -#define E1_STEP_PIN PA0 -#define E1_DIR_PIN PB6 -#define E1_ENABLE_PIN PA1 - -#define E2_STEP_PIN PC14 -#define E2_DIR_PIN PC13 -#define E2_ENABLE_PIN PC15 - -// -// Heaters / Fans -// -#define HEATER_0_PIN PB0 -#define HEATER_1_PIN PB5 -#define HEATER_2_PIN PB4 -#define HEATER_BED_PIN PB1 - -#define FAN_PIN PB7 // TODO: Add functionality -#define FAN1_PIN PB8 // TODO: Add functionality -#define FAN2_PIN PB9 // TODO: Add functionality - -// -// Temperature Sensors -// -#define TEMP_0_PIN PC2 // PORT NUMBERING -#define TEMP_1_PIN PC1 // PORT NUMBERING -#define TEMP_2_PIN PC0 // PORT NUMBERING -#define TEMP_BED_PIN PC3 // PORT NUMBERING - -// -// Misc. Functions -// -#define LED_PWM PD12 // External LED, pin 2 on LED labeled connector -//#define RESET_PIN NRST -#define T_PEN PE6 - -#define BEEPER_PIN PB10 - -// -// LCD / Controller -// -#if HAS_SPI_LCD - - #if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) - #define LCD_PINS_RS PE6 // CS chip select /SS chip slave select - #define LCD_PINS_ENABLE PE14 // SID (MOSI) - #define LCD_PINS_D4 PD8 // SCK (CLK) clock - #define LCD_PINS_D5 PD9 - #define LCD_PINS_D6 PD10 - #define LCD_PINS_D7 PE15 - - #define BTN_EN1 PE8 - #define BTN_EN2 PE9 - #define BTN_ENC PE13 - - #define SD_DETECT_PIN PC7 - #define KILL_PIN -1 - #endif - - #ifndef ST7920_DELAY_1 - #define ST7920_DELAY_1 DELAY_NS(96) - #endif - #ifndef ST7920_DELAY_2 - #define ST7920_DELAY_2 DELAY_NS(48) - #endif - #ifndef ST7920_DELAY_3 - #define ST7920_DELAY_3 DELAY_NS(715) - #endif - - // - // UART LCD Pins, if used - // - //#define LCD_PINS_D14 PD9 // RXD3 - //#define LCD_PINS_D13 PD8 // TXD3 - -#endif // HAS_SPI_LCD - -// -// SPI2 on LCD conn -// -#define SPI2_MOSI PB15 -#define SPI2_MISO PB14 -#define SPI2_SCK PB13 -#define SPI2_NSS PB12 - -// -// SD Card on LCD -// -#define SD_CD PC7 -#define SD_DATA0 PC8 -#define SD_DATA1 PC9 -#define SD_DATA2 PC10 -#define SD_DATA3 PC11 -#define SD_CMD PD2 -#define SD_CLK PC12 - -// -// SPI Flash (on board Card Socket) -// -#define SPI1_NSS PA4 -#define SPI1_SCK PA5 -#define SPI1_MISO PA6 -#define SPI1_MOSI PA7 - -// -// Debug -// -//#define SDA PA13 -//#define SCL PA14 - -// -// Wifi -// -#define USART2_RX PA3 // Default alternate function -#define USART2_TX PA2 // Default alternate function - -// -// For future use -// -//#undef USB_DM -//#undef CAN_TX -//#undef USB_DP -//#undef CAN_RX -//#undef BOARD_JTDI_PIN -//#define BOOT0 BOOT0 diff --git a/Marlin/src/pins/pins_EINSY_RAMBO.h b/Marlin/src/pins/rambo/pins_EINSY_RAMBO.h similarity index 97% rename from Marlin/src/pins/pins_EINSY_RAMBO.h rename to Marlin/src/pins/rambo/pins_EINSY_RAMBO.h index c40bc079cb..56a597ffc3 100644 --- a/Marlin/src/pins/pins_EINSY_RAMBO.h +++ b/Marlin/src/pins/rambo/pins_EINSY_RAMBO.h @@ -135,8 +135,8 @@ // M3/M4/M5 - Spindle/Laser Control // // use P1 connector for spindle pins -#define SPINDLE_LASER_PWM_PIN 9 // MUST BE HARDWARE PWM -#define SPINDLE_LASER_ENA_PIN 18 // Pin should have a pullup! +#define SPINDLE_LASER_PWM_PIN 9 // Hardware PWM +#define SPINDLE_LASER_ENA_PIN 18 // Pullup! #define SPINDLE_DIR_PIN 19 // diff --git a/Marlin/src/pins/pins_EINSY_RETRO.h b/Marlin/src/pins/rambo/pins_EINSY_RETRO.h similarity index 97% rename from Marlin/src/pins/pins_EINSY_RETRO.h rename to Marlin/src/pins/rambo/pins_EINSY_RETRO.h index 2206191474..675f5e3de0 100644 --- a/Marlin/src/pins/pins_EINSY_RETRO.h +++ b/Marlin/src/pins/rambo/pins_EINSY_RETRO.h @@ -149,8 +149,8 @@ // M3/M4/M5 - Spindle/Laser Control // // use P1 connector for spindle pins -#define SPINDLE_LASER_PWM_PIN 9 // MUST BE HARDWARE PWM -#define SPINDLE_LASER_ENA_PIN 18 // Pin should have a pullup! +#define SPINDLE_LASER_PWM_PIN 9 // Hardware PWM +#define SPINDLE_LASER_ENA_PIN 18 // Pullup! #define SPINDLE_DIR_PIN 19 // diff --git a/Marlin/src/pins/pins_MINIRAMBO.h b/Marlin/src/pins/rambo/pins_MINIRAMBO.h similarity index 97% rename from Marlin/src/pins/pins_MINIRAMBO.h rename to Marlin/src/pins/rambo/pins_MINIRAMBO.h index f81627b655..da4f77f7dd 100644 --- a/Marlin/src/pins/pins_MINIRAMBO.h +++ b/Marlin/src/pins/rambo/pins_MINIRAMBO.h @@ -125,8 +125,8 @@ // M3/M4/M5 - Spindle/Laser Control // // use P1 connector for spindle pins -#define SPINDLE_LASER_PWM_PIN 9 // MUST BE HARDWARE PWM -#define SPINDLE_LASER_ENA_PIN 18 // Pin should have a pullup! +#define SPINDLE_LASER_PWM_PIN 9 // Hardware PWM +#define SPINDLE_LASER_ENA_PIN 18 // Pullup! #define SPINDLE_DIR_PIN 19 // diff --git a/Marlin/src/pins/pins_RAMBO.h b/Marlin/src/pins/rambo/pins_RAMBO.h similarity index 97% rename from Marlin/src/pins/pins_RAMBO.h rename to Marlin/src/pins/rambo/pins_RAMBO.h index 1eb29a66a4..10a6a1b5b9 100644 --- a/Marlin/src/pins/pins_RAMBO.h +++ b/Marlin/src/pins/rambo/pins_RAMBO.h @@ -149,8 +149,8 @@ // // M3/M4/M5 - Spindle/Laser Control // -#define SPINDLE_LASER_PWM_PIN 45 // MUST BE HARDWARE PWM -#define SPINDLE_LASER_ENA_PIN 31 // Pin should have a pullup! +#define SPINDLE_LASER_PWM_PIN 45 // Hardware PWM +#define SPINDLE_LASER_ENA_PIN 31 // Pullup! #define SPINDLE_DIR_PIN 32 // diff --git a/Marlin/src/pins/pins_SCOOVO_X9H.h b/Marlin/src/pins/rambo/pins_SCOOVO_X9H.h similarity index 100% rename from Marlin/src/pins/pins_SCOOVO_X9H.h rename to Marlin/src/pins/rambo/pins_SCOOVO_X9H.h diff --git a/Marlin/src/pins/pins_3DRAG.h b/Marlin/src/pins/ramps/pins_3DRAG.h similarity index 91% rename from Marlin/src/pins/pins_3DRAG.h rename to Marlin/src/pins/ramps/pins_3DRAG.h index a7e686eef0..eae958da69 100644 --- a/Marlin/src/pins/pins_3DRAG.h +++ b/Marlin/src/pins/ramps/pins_3DRAG.h @@ -30,7 +30,7 @@ #endif #ifndef DEFAULT_MACHINE_NAME - #define DEFAULT_MACHINE_NAME "3Drag" + #define DEFAULT_MACHINE_NAME BOARD_NAME #endif #ifndef DEFAULT_SOURCE_CODE_URL @@ -44,7 +44,7 @@ #define RAMPS_D9_PIN 8 #define MOSFET_D_PIN 12 -#define CASE_LIGHT_PIN -1 // MUST BE HARDWARE PWM but one is not available on expansion header +#define CASE_LIGHT_PIN -1 // Hardware PWM but one is not available on expansion header #include "pins_RAMPS.h" @@ -152,11 +152,11 @@ #define Z_DIR_PIN 28 #define Z_ENABLE_PIN 24 #define Z_STEP_PIN 26 - #define SPINDLE_LASER_PWM_PIN 46 // MUST BE HARDWARE PWM - #define SPINDLE_LASER_ENA_PIN 62 // Pin should have a pullup! + #define SPINDLE_LASER_PWM_PIN 46 // Hardware PWM + #define SPINDLE_LASER_ENA_PIN 62 // Pullup! #define SPINDLE_DIR_PIN 48 #elif !BOTH(ULTRA_LCD, NEWPANEL) // use expansion header if no LCD in use - #define SPINDLE_LASER_ENA_PIN 16 // Pin should have a pullup/pulldown! + #define SPINDLE_LASER_ENA_PIN 16 // Pullup or pulldown! #define SPINDLE_DIR_PIN 17 #endif #endif diff --git a/Marlin/src/pins/pins_AZTEEG_X3.h b/Marlin/src/pins/ramps/pins_AZTEEG_X3.h similarity index 93% rename from Marlin/src/pins/pins_AZTEEG_X3.h rename to Marlin/src/pins/ramps/pins_AZTEEG_X3.h index 4686d9e726..06686a016b 100644 --- a/Marlin/src/pins/pins_AZTEEG_X3.h +++ b/Marlin/src/pins/ramps/pins_AZTEEG_X3.h @@ -27,9 +27,7 @@ #ifndef __AVR_ATmega2560__ #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'" -#endif - -#if HOTENDS > 2 || E_STEPPERS > 2 +#elif HOTENDS > 2 || E_STEPPERS > 2 #error "Azteeg X3 supports up to 2 hotends / E-steppers. Comment out this line to continue." #endif @@ -92,7 +90,7 @@ #undef SERVO0_PIN #define SERVO0_PIN 11 #endif - #define SPINDLE_LASER_PWM_PIN 7 // MUST BE HARDWARE PWM - #define SPINDLE_LASER_ENA_PIN 20 // Pin should have a pullup! + #define SPINDLE_LASER_PWM_PIN 7 // Hardware PWM + #define SPINDLE_LASER_ENA_PIN 20 // Pullup! #define SPINDLE_DIR_PIN 21 #endif diff --git a/Marlin/src/pins/pins_AZTEEG_X3_PRO.h b/Marlin/src/pins/ramps/pins_AZTEEG_X3_PRO.h similarity index 93% rename from Marlin/src/pins/pins_AZTEEG_X3_PRO.h rename to Marlin/src/pins/ramps/pins_AZTEEG_X3_PRO.h index 25282f1eef..195f742ad4 100644 --- a/Marlin/src/pins/pins_AZTEEG_X3_PRO.h +++ b/Marlin/src/pins/ramps/pins_AZTEEG_X3_PRO.h @@ -27,9 +27,7 @@ #ifndef __AVR_ATmega2560__ #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'" -#endif - -#if HOTENDS > 5 || E_STEPPERS > 5 +#elif HOTENDS > 5 || E_STEPPERS > 5 #error "Azteeg X3 Pro supports up to 5 hotends / E-steppers. Comment out this line to continue." #endif @@ -160,10 +158,9 @@ #if HAS_CUTTER // EXP2 header #if ANY(VIKI2, miniVIKI) - #undef BTN_EN2 - #define BTN_EN2 31 // need 7 for the spindle speed PWM + #define BTN_EN2 31 // Pin 7 needed for Spindle PWM #endif - #define SPINDLE_LASER_PWM_PIN 7 // must have a hardware PWM - #define SPINDLE_LASER_ENA_PIN 20 // Pin should have a pullup! - #define SPINDLE_DIR_PIN 21 + #define SPINDLE_LASER_PWM_PIN 7 // Hardware PWM + #define SPINDLE_LASER_ENA_PIN 20 // Pullup! + #define SPINDLE_DIR_PIN 21 #endif diff --git a/Marlin/src/pins/pins_BAM_DICE_DUE.h b/Marlin/src/pins/ramps/pins_BAM_DICE_DUE.h similarity index 90% rename from Marlin/src/pins/pins_BAM_DICE_DUE.h rename to Marlin/src/pins/ramps/pins_BAM_DICE_DUE.h index 7872d66b31..74a69fb8c4 100644 --- a/Marlin/src/pins/pins_BAM_DICE_DUE.h +++ b/Marlin/src/pins/ramps/pins_BAM_DICE_DUE.h @@ -34,9 +34,9 @@ // // M3/M4/M5 - Spindle/Laser Control // -#define SPINDLE_LASER_ENA_PIN 66 // Pin should have a pullup/pulldown! +#define SPINDLE_LASER_ENA_PIN 66 // Pullup or pulldown! #define SPINDLE_DIR_PIN 67 -#define SPINDLE_LASER_PWM_PIN 44 // MUST BE HARDWARE PWM +#define SPINDLE_LASER_PWM_PIN 44 // Hardware PWM #include "pins_RAMPS.h" diff --git a/Marlin/src/pins/pins_BIQU_KFB_2.h b/Marlin/src/pins/ramps/pins_BIQU_KFB_2.h similarity index 100% rename from Marlin/src/pins/pins_BIQU_KFB_2.h rename to Marlin/src/pins/ramps/pins_BIQU_KFB_2.h diff --git a/Marlin/src/pins/pins_BQ_ZUM_MEGA_3D.h b/Marlin/src/pins/ramps/pins_BQ_ZUM_MEGA_3D.h similarity index 93% rename from Marlin/src/pins/pins_BQ_ZUM_MEGA_3D.h rename to Marlin/src/pins/ramps/pins_BQ_ZUM_MEGA_3D.h index 9290e6c3b1..5a49c0a3b6 100644 --- a/Marlin/src/pins/pins_BQ_ZUM_MEGA_3D.h +++ b/Marlin/src/pins/ramps/pins_BQ_ZUM_MEGA_3D.h @@ -50,8 +50,8 @@ // // M3/M4/M5 - Spindle/Laser Control // -#define SPINDLE_LASER_ENA_PIN 40 // Pin should have a pullup/pulldown! -#define SPINDLE_LASER_PWM_PIN 44 // MUST BE HARDWARE PWM +#define SPINDLE_LASER_ENA_PIN 40 // Pullup or pulldown! +#define SPINDLE_LASER_PWM_PIN 44 // Hardware PWM #define SPINDLE_DIR_PIN 42 // @@ -94,7 +94,7 @@ #undef PS_ON_PIN // 12 #define PS_ON_PIN 81 // External Power Supply -#define CASE_LIGHT_PIN 44 // MUST BE HARDWARE PWM +#define CASE_LIGHT_PIN 44 // Hardware PWM // This board has headers for Z-min, Z-max and IND_S_5V *but* as the bq team diff --git a/Marlin/src/pins/pins_DUPLICATOR_I3_PLUS.h b/Marlin/src/pins/ramps/pins_DUPLICATOR_I3_PLUS.h similarity index 99% rename from Marlin/src/pins/pins_DUPLICATOR_I3_PLUS.h rename to Marlin/src/pins/ramps/pins_DUPLICATOR_I3_PLUS.h index 94585715e2..290637eb7b 100644 --- a/Marlin/src/pins/pins_DUPLICATOR_I3_PLUS.h +++ b/Marlin/src/pins/ramps/pins_DUPLICATOR_I3_PLUS.h @@ -29,7 +29,7 @@ #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'" #endif -#define BOARD_NAME "Duplicator i3 Plus" +#define BOARD_NAME "Duplicator i3 Plus" // // Limit Switches diff --git a/Marlin/src/pins/pins_FELIX2.h b/Marlin/src/pins/ramps/pins_FELIX2.h similarity index 97% rename from Marlin/src/pins/pins_FELIX2.h rename to Marlin/src/pins/ramps/pins_FELIX2.h index ec02cc22ce..5a1f650583 100644 --- a/Marlin/src/pins/pins_FELIX2.h +++ b/Marlin/src/pins/ramps/pins_FELIX2.h @@ -42,8 +42,7 @@ // // Misc. Functions // -#undef SDPOWER -#define SDPOWER 1 +#define SDPOWER_PIN 1 #define PS_ON_PIN 12 diff --git a/Marlin/src/pins/pins_FORMBOT_RAPTOR.h b/Marlin/src/pins/ramps/pins_FORMBOT_RAPTOR.h similarity index 87% rename from Marlin/src/pins/pins_FORMBOT_RAPTOR.h rename to Marlin/src/pins/ramps/pins_FORMBOT_RAPTOR.h index 762feaa6d4..292e713af4 100644 --- a/Marlin/src/pins/pins_FORMBOT_RAPTOR.h +++ b/Marlin/src/pins/ramps/pins_FORMBOT_RAPTOR.h @@ -27,18 +27,12 @@ #ifndef __AVR_ATmega2560__ #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'" +#elif HOTENDS > 3 || E_STEPPERS > 3 + #error "Formbot supports up to 3 hotends / E-steppers. Comment out this line to continue." #endif -#if HOTENDS > 3 || E_STEPPERS > 3 - #error "Formbot supports up to 3 hotends / E-steppers. Comment this line to keep going." -#endif - -#ifndef DEFAULT_MACHINE_NAME - #define DEFAULT_MACHINE_NAME "Formbot Raptor" -#endif -#ifndef BOARD_NAME - #define BOARD_NAME "Formbot Raptor" -#endif +#define BOARD_NAME "Formbot Raptor" +#define DEFAULT_MACHINE_NAME BOARD_NAME // // Servos @@ -117,15 +111,15 @@ // SPI for Max6675 or Max31855 Thermocouple #if DISABLED(SDSUPPORT) - #define MAX6675_SS_PIN 66 // Do not use pin 53 if there is even the remote possibility of using Display/SD card + #define MAX6675_SS_PIN 66 // Don't use 53 if there is even the remote possibility of using Display/SD card #else - #define MAX6675_SS_PIN 66 // Do not use pin 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present + #define MAX6675_SS_PIN 66 // Don't use 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present #endif // // Augmentation for auto-assigning RAMPS plugs // -#if DISABLED(IS_RAMPS_EEB, IS_RAMPS_EEF, IS_RAMPS_EFB, IS_RAMPS_EFF, IS_RAMPS_SF) && !PIN_EXISTS(MOSFET_D) +#if NONE(IS_RAMPS_EEB, IS_RAMPS_EEF, IS_RAMPS_EFB, IS_RAMPS_EFF, IS_RAMPS_SF) && !PIN_EXISTS(MOSFET_D) #if HOTENDS > 1 #if TEMP_SENSOR_BED #define IS_RAMPS_EEB diff --git a/Marlin/src/pins/pins_FORMBOT_RAPTOR2.h b/Marlin/src/pins/ramps/pins_FORMBOT_RAPTOR2.h similarity index 80% rename from Marlin/src/pins/pins_FORMBOT_RAPTOR2.h rename to Marlin/src/pins/ramps/pins_FORMBOT_RAPTOR2.h index e89167e987..b5c69a06d1 100644 --- a/Marlin/src/pins/pins_FORMBOT_RAPTOR2.h +++ b/Marlin/src/pins/ramps/pins_FORMBOT_RAPTOR2.h @@ -25,8 +25,8 @@ * Formbot Raptor 2 pin assignments */ -#define DEFAULT_MACHINE_NAME "Formbot Raptor2" #define BOARD_NAME "Formbot Raptor2" +#define DEFAULT_MACHINE_NAME BOARD_NAME #define FAN_PIN 6 @@ -43,21 +43,21 @@ // #if HAS_CUTTER && !PIN_EXISTS(SPINDLE_LASER_ENA) #if !NUM_SERVOS // Try to use servo connector first - #define SPINDLE_LASER_ENA_PIN 6 // Pin should have a pullup/pulldown! - #define SPINDLE_LASER_PWM_PIN 4 // MUST BE HARDWARE PWM + #define SPINDLE_LASER_ENA_PIN 6 // Pullup or pulldown! + #define SPINDLE_LASER_PWM_PIN 4 // Hardware PWM #define SPINDLE_DIR_PIN 5 #elif !GREEDY_PANEL // Try to use AUX2 - #define SPINDLE_LASER_ENA_PIN 40 // Pin should have a pullup/pulldown! - #define SPINDLE_LASER_PWM_PIN 44 // MUST BE HARDWARE PWM + #define SPINDLE_LASER_ENA_PIN 40 // Pullup or pulldown! + #define SPINDLE_LASER_PWM_PIN 44 // Hardware PWM #define SPINDLE_DIR_PIN 65 #endif #endif #if ENABLED(CASE_LIGHT_ENABLE) && !PIN_EXISTS(CASE_LIGHT) #if NUM_SERVOS <= 1 // Try to use servo connector first - #define CASE_LIGHT_PIN 6 // MUST BE HARDWARE PWM + #define CASE_LIGHT_PIN 6 // Hardware PWM #elif !GREEDY_PANEL // Try to use AUX2 - #define CASE_LIGHT_PIN 44 // MUST BE HARDWARE PWM + #define CASE_LIGHT_PIN 44 // Hardware PWM #endif #endif diff --git a/Marlin/src/pins/pins_FORMBOT_TREX2PLUS.h b/Marlin/src/pins/ramps/pins_FORMBOT_TREX2PLUS.h similarity index 90% rename from Marlin/src/pins/pins_FORMBOT_TREX2PLUS.h rename to Marlin/src/pins/ramps/pins_FORMBOT_TREX2PLUS.h index f3b12ee1bc..319a415cd3 100644 --- a/Marlin/src/pins/pins_FORMBOT_TREX2PLUS.h +++ b/Marlin/src/pins/ramps/pins_FORMBOT_TREX2PLUS.h @@ -27,14 +27,12 @@ #ifndef __AVR_ATmega2560__ #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'" +#elif HOTENDS > 2 || E_STEPPERS > 2 + #error "Formbot supports up to 2 hotends / E-steppers. Comment out this line to continue." #endif -#if HOTENDS > 2 || E_STEPPERS > 2 - #error "Formbot supports up to 2 hotends / E-steppers. Comment this line to keep going." -#endif - -#define DEFAULT_MACHINE_NAME "Formbot" #define BOARD_NAME "Formbot" +#define DEFAULT_MACHINE_NAME BOARD_NAME // // Servos @@ -114,15 +112,15 @@ // SPI for Max6675 or Max31855 Thermocouple #if DISABLED(SDSUPPORT) - #define MAX6675_SS_PIN 66 // Do not use pin 53 if there is even the remote possibility of using Display/SD card + #define MAX6675_SS_PIN 66 // Don't use 53 if there is even the remote possibility of using Display/SD card #else - #define MAX6675_SS_PIN 66 // Do not use pin 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present + #define MAX6675_SS_PIN 66 // Don't use 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present #endif // // Augmentation for auto-assigning RAMPS plugs // -#if DISABLED(IS_RAMPS_EEB, IS_RAMPS_EEF, IS_RAMPS_EFB, IS_RAMPS_EFF, IS_RAMPS_SF) && !PIN_EXISTS(MOSFET_D) +#if NONE(IS_RAMPS_EEB, IS_RAMPS_EEF, IS_RAMPS_EFB, IS_RAMPS_EFF, IS_RAMPS_SF) && !PIN_EXISTS(MOSFET_D) #if HOTENDS > 1 #if TEMP_SENSOR_BED #define IS_RAMPS_EEB diff --git a/Marlin/src/pins/pins_FORMBOT_TREX3.h b/Marlin/src/pins/ramps/pins_FORMBOT_TREX3.h similarity index 88% rename from Marlin/src/pins/pins_FORMBOT_TREX3.h rename to Marlin/src/pins/ramps/pins_FORMBOT_TREX3.h index 4ca2556d80..111a10d645 100644 --- a/Marlin/src/pins/pins_FORMBOT_TREX3.h +++ b/Marlin/src/pins/ramps/pins_FORMBOT_TREX3.h @@ -27,14 +27,12 @@ #ifndef __AVR_ATmega2560__ #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'" +#elif HOTENDS > 2 || E_STEPPERS > 2 + #error "Formbot supports up to 2 hotends / E-steppers. Comment out this line to continue." #endif -#if HOTENDS > 2 || E_STEPPERS > 2 - #error "Formbot supports up to 2 hotends / E-steppers. Comment this line to keep going." -#endif - -#define DEFAULT_MACHINE_NAME "Formbot" #define BOARD_NAME "Formbot" +#define DEFAULT_MACHINE_NAME BOARD_NAME // // Servos @@ -114,9 +112,9 @@ // SPI for Max6675 or Max31855 Thermocouple #if DISABLED(SDSUPPORT) - #define MAX6675_SS_PIN 66 // Do not use pin 53 if there is even the remote possibility of using Display/SD card + #define MAX6675_SS_PIN 66 // Don't use 53 if there is even the remote possibility of using Display/SD card #else - #define MAX6675_SS_PIN 66 // Do not use pin 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present + #define MAX6675_SS_PIN 66 // Don't use 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present #endif @@ -144,8 +142,8 @@ #define LED_PIN 13 #endif -#define SPINDLE_LASER_PWM_PIN -1 // MUST BE HARDWARE PWM -#define SPINDLE_LASER_ENA_PIN 4 // Pin should have a pullup! +#define SPINDLE_LASER_PWM_PIN -1 // Hardware PWM +#define SPINDLE_LASER_ENA_PIN 4 // Pullup! // Use the RAMPS 1.4 Analog input 5 on the AUX2 connector #define FILWIDTH_PIN 5 // Analog Input diff --git a/Marlin/src/pins/pins_FYSETC_F6_13.h b/Marlin/src/pins/ramps/pins_FYSETC_F6_13.h similarity index 96% rename from Marlin/src/pins/pins_FYSETC_F6_13.h rename to Marlin/src/pins/ramps/pins_FYSETC_F6_13.h index e41cca85cd..678b9c30ac 100644 --- a/Marlin/src/pins/pins_FYSETC_F6_13.h +++ b/Marlin/src/pins/ramps/pins_FYSETC_F6_13.h @@ -22,7 +22,7 @@ #pragma once // -// Fysetc F6 pin assignments +// FYSETC F6 pin assignments // #ifndef __AVR_ATmega2560__ @@ -117,9 +117,13 @@ // the jumper next to the limit switch socket when using sensorless homing. // -#if HAS_DRIVER(TMC2208) || HAS_DRIVER(TMC2209) - // Software serial - // At the moment, F6 rx pins are not pc interrupt pins +#if HAS_TMC220x + /** + * TMC2208/TMC2209 stepper drivers + * + * Software serial communication pins. + * At the moment, F6 rx pins are not pc interrupt pins + */ #define X_SERIAL_RX_PIN -1 // 71 #define X_SERIAL_TX_PIN 72 #define Y_SERIAL_RX_PIN -1 // 73 diff --git a/Marlin/src/pins/pins_K8200.h b/Marlin/src/pins/ramps/pins_K8200.h similarity index 100% rename from Marlin/src/pins/pins_K8200.h rename to Marlin/src/pins/ramps/pins_K8200.h diff --git a/Marlin/src/pins/pins_K8400.h b/Marlin/src/pins/ramps/pins_K8400.h similarity index 100% rename from Marlin/src/pins/pins_K8400.h rename to Marlin/src/pins/ramps/pins_K8400.h index c3dd647d64..908b6e61e0 100644 --- a/Marlin/src/pins/pins_K8400.h +++ b/Marlin/src/pins/ramps/pins_K8400.h @@ -32,8 +32,8 @@ * - Second heater has moved pin */ -#define DEFAULT_MACHINE_NAME "Vertex" #define BOARD_NAME "K8400" +#define DEFAULT_MACHINE_NAME "Vertex" #include "pins_3DRAG.h" diff --git a/Marlin/src/pins/pins_K8800.h b/Marlin/src/pins/ramps/pins_K8800.h similarity index 100% rename from Marlin/src/pins/pins_K8800.h rename to Marlin/src/pins/ramps/pins_K8800.h index 98fcde5bcd..22b5081db4 100644 --- a/Marlin/src/pins/pins_K8800.h +++ b/Marlin/src/pins/ramps/pins_K8800.h @@ -29,8 +29,8 @@ #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'" #endif -#define DEFAULT_MACHINE_NAME "Vertex Delta" #define BOARD_NAME "K8800" +#define DEFAULT_MACHINE_NAME "Vertex Delta" //#define LCD_SCREEN_ROT_180 diff --git a/Marlin/src/pins/pins_MAKEBOARD_MINI.h b/Marlin/src/pins/ramps/pins_MAKEBOARD_MINI.h similarity index 86% rename from Marlin/src/pins/pins_MAKEBOARD_MINI.h rename to Marlin/src/pins/ramps/pins_MAKEBOARD_MINI.h index 30807d2a18..03f6ca0396 100644 --- a/Marlin/src/pins/pins_MAKEBOARD_MINI.h +++ b/Marlin/src/pins/ramps/pins_MAKEBOARD_MINI.h @@ -21,20 +21,13 @@ */ #pragma once -#include "pins_RAMPS.h" - -#undef BOARD_NAME -#define BOARD_NAME "MAKEBOARD_MINI" +#define BOARD_NAME "MAKEboard Mini" // // Only 3 Limit Switch plugs on Micromake C1 // -#undef X_MIN_PIN -#undef Y_MIN_PIN -#undef Z_MIN_PIN -#undef X_MAX_PIN -#undef Y_MAX_PIN -#undef Z_MAX_PIN #define X_STOP_PIN 2 #define Y_STOP_PIN 15 #define Z_STOP_PIN 19 + +#include "pins_RAMPS.h" diff --git a/Marlin/src/pins/pins_MKS_BASE.h b/Marlin/src/pins/ramps/pins_MKS_BASE.h similarity index 91% rename from Marlin/src/pins/pins_MKS_BASE.h rename to Marlin/src/pins/ramps/pins_MKS_BASE.h index 07519a5696..9ec23c1a80 100644 --- a/Marlin/src/pins/pins_MKS_BASE.h +++ b/Marlin/src/pins/ramps/pins_MKS_BASE.h @@ -44,8 +44,8 @@ // // M3/M4/M5 - Spindle/Laser Control // -#define SPINDLE_LASER_PWM_PIN 2 // MUST BE HARDWARE PWM -#define SPINDLE_LASER_ENA_PIN 15 // Pin should have a pullup! +#define SPINDLE_LASER_PWM_PIN 2 // Hardware PWM +#define SPINDLE_LASER_ENA_PIN 15 // Pullup! #define SPINDLE_DIR_PIN 19 #include "pins_RAMPS.h" diff --git a/Marlin/src/pins/pins_MKS_BASE_14.h b/Marlin/src/pins/ramps/pins_MKS_BASE_14.h similarity index 100% rename from Marlin/src/pins/pins_MKS_BASE_14.h rename to Marlin/src/pins/ramps/pins_MKS_BASE_14.h diff --git a/Marlin/src/pins/pins_MKS_BASE_15.h b/Marlin/src/pins/ramps/pins_MKS_BASE_15.h similarity index 100% rename from Marlin/src/pins/pins_MKS_BASE_15.h rename to Marlin/src/pins/ramps/pins_MKS_BASE_15.h diff --git a/Marlin/src/pins/pins_MKS_BASE_HEROIC.h b/Marlin/src/pins/ramps/pins_MKS_BASE_HEROIC.h similarity index 100% rename from Marlin/src/pins/pins_MKS_BASE_HEROIC.h rename to Marlin/src/pins/ramps/pins_MKS_BASE_HEROIC.h diff --git a/Marlin/src/pins/pins_MKS_GEN_13.h b/Marlin/src/pins/ramps/pins_MKS_GEN_13.h similarity index 98% rename from Marlin/src/pins/pins_MKS_GEN_13.h rename to Marlin/src/pins/ramps/pins_MKS_GEN_13.h index 3d777d8383..705d358e02 100644 --- a/Marlin/src/pins/pins_MKS_GEN_13.h +++ b/Marlin/src/pins/ramps/pins_MKS_GEN_13.h @@ -96,6 +96,8 @@ #undef SD_DETECT_PIN #undef BEEPER_PIN #undef KILL_PIN + #undef STAT_LED_RED_PIN + #undef STAT_LED_BLUE_PIN // // VIKI2 12-wire lead diff --git a/Marlin/src/pins/pins_MKS_GEN_L.h b/Marlin/src/pins/ramps/pins_MKS_GEN_L.h similarity index 100% rename from Marlin/src/pins/pins_MKS_GEN_L.h rename to Marlin/src/pins/ramps/pins_MKS_GEN_L.h diff --git a/Marlin/src/pins/pins_RAMPS.h b/Marlin/src/pins/ramps/pins_RAMPS.h similarity index 85% rename from Marlin/src/pins/pins_RAMPS.h rename to Marlin/src/pins/ramps/pins_RAMPS.h index 3093a803ca..5e6b5fa117 100644 --- a/Marlin/src/pins/pins_RAMPS.h +++ b/Marlin/src/pins/ramps/pins_RAMPS.h @@ -51,7 +51,7 @@ #error "Oops! Set MOTHERBOARD to an STM32F1-based board when building for STM32F1." #endif -#if DISABLED(IS_RAMPS_SMART, IS_RAMPS_DUO, IS_RAMPS4DUE, TARGET_LPC1768) +#if NONE(IS_RAMPS_SMART, IS_RAMPS_DUO, IS_RAMPS4DUE, TARGET_LPC1768) #if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__) #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'" #endif @@ -157,21 +157,27 @@ // // Temperature Sensors // -#define TEMP_0_PIN 13 // Analog Input -#define TEMP_1_PIN 15 // Analog Input -#define TEMP_BED_PIN 14 // Analog Input +#ifndef TEMP_0_PIN + #define TEMP_0_PIN 13 // Analog Input +#endif +#ifndef TEMP_1_PIN + #define TEMP_1_PIN 15 // Analog Input +#endif +#ifndef TEMP_BED_PIN + #define TEMP_BED_PIN 14 // Analog Input +#endif // SPI for Max6675 or Max31855 Thermocouple #if DISABLED(SDSUPPORT) - #define MAX6675_SS_PIN 66 // Do not use pin 53 if there is even the remote possibility of using Display/SD card + #define MAX6675_SS_PIN 66 // Don't use 53 if there is even the remote possibility of using Display/SD card #else - #define MAX6675_SS_PIN 66 // Do not use pin 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present + #define MAX6675_SS_PIN 66 // Don't use 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present #endif // // Augmentation for auto-assigning RAMPS plugs // -#if DISABLED(IS_RAMPS_EEB, IS_RAMPS_EEF, IS_RAMPS_EFB, IS_RAMPS_EFF, IS_RAMPS_SF) && !PIN_EXISTS(MOSFET_D) +#if NONE(IS_RAMPS_EEB, IS_RAMPS_EEF, IS_RAMPS_EFB, IS_RAMPS_EFF, IS_RAMPS_SF) && !PIN_EXISTS(MOSFET_D) #if HOTENDS > 1 #if TEMP_SENSOR_BED #define IS_RAMPS_EEB @@ -252,13 +258,11 @@ #define PS_ON_PIN 12 #endif -#define AUX2_PINS_FREE !( BOTH(ULTRA_LCD, NEWPANEL) && ANY(PANEL_ONE, VIKI2, miniVIKI, MINIPANEL, REPRAPWORLD_KEYPAD) ) - #if ENABLED(CASE_LIGHT_ENABLE) && !defined(CASE_LIGHT_PIN) && !defined(SPINDLE_LASER_ENA_PIN) - #if NUM_SERVOS <= 1 // try to use servo connector first - #define CASE_LIGHT_PIN 6 // MUST BE HARDWARE PWM - #elif AUX2_PINS_FREE - #define CASE_LIGHT_PIN 44 // MUST BE HARDWARE PWM + #if NUM_SERVOS <= 1 // Prefer the servo connector + #define CASE_LIGHT_PIN 6 // Hardware PWM + #elif HAS_FREE_AUX2_PINS + #define CASE_LIGHT_PIN 44 // Hardware PWM #endif #endif @@ -267,20 +271,18 @@ // #if HAS_CUTTER && !defined(SPINDLE_LASER_ENA_PIN) #if !NUM_SERVOS // Use servo connector if possible - #define SPINDLE_LASER_ENA_PIN 4 // Pin should have a pullup/pulldown! - #define SPINDLE_LASER_PWM_PIN 6 // MUST BE HARDWARE PWM + #define SPINDLE_LASER_ENA_PIN 4 // Pullup or pulldown! + #define SPINDLE_LASER_PWM_PIN 6 // Hardware PWM #define SPINDLE_DIR_PIN 5 - #elif AUX2_PINS_FREE - #define SPINDLE_LASER_ENA_PIN 40 // Pin should have a pullup/pulldown! - #define SPINDLE_LASER_PWM_PIN 44 // MUST BE HARDWARE PWM + #elif HAS_FREE_AUX2_PINS + #define SPINDLE_LASER_ENA_PIN 40 // Pullup or pulldown! + #define SPINDLE_LASER_PWM_PIN 44 // Hardware PWM #define SPINDLE_DIR_PIN 65 #else #error "No auto-assignable Spindle/Laser pins available." #endif #endif -#undef AUX2_PINS_FREE - // // TMC software SPI // @@ -296,7 +298,7 @@ #endif #endif -#if HAS_DRIVER(TMC2208) || HAS_DRIVER(TMC2209) +#if HAS_TMC220x /** * TMC2208/TMC2209 stepper drivers * @@ -319,31 +321,75 @@ // Software serial // - #define X_SERIAL_TX_PIN 40 - #define X_SERIAL_RX_PIN 63 - #define X2_SERIAL_TX_PIN -1 - #define X2_SERIAL_RX_PIN -1 + #ifndef X_SERIAL_TX_PIN + #define X_SERIAL_TX_PIN 40 + #endif + #ifndef X_SERIAL_RX_PIN + #define X_SERIAL_RX_PIN 63 + #endif + #ifndef X2_SERIAL_TX_PIN + #define X2_SERIAL_TX_PIN -1 + #endif + #ifndef X2_SERIAL_RX_PIN + #define X2_SERIAL_RX_PIN -1 + #endif - #define Y_SERIAL_TX_PIN 59 - #define Y_SERIAL_RX_PIN 64 - #define Y2_SERIAL_TX_PIN -1 - #define Y2_SERIAL_RX_PIN -1 + #ifndef Y_SERIAL_TX_PIN + #define Y_SERIAL_TX_PIN 59 + #endif + #ifndef Y_SERIAL_RX_PIN + #define Y_SERIAL_RX_PIN 64 + #endif + #ifndef Y2_SERIAL_TX_PIN + #define Y2_SERIAL_TX_PIN -1 + #endif + #ifndef Y2_SERIAL_RX_PIN + #define Y2_SERIAL_RX_PIN -1 + #endif - #define Z_SERIAL_TX_PIN 42 - #define Z_SERIAL_RX_PIN 65 - #define Z2_SERIAL_TX_PIN -1 - #define Z2_SERIAL_RX_PIN -1 + #ifndef Z_SERIAL_TX_PIN + #define Z_SERIAL_TX_PIN 42 + #endif + #ifndef Z_SERIAL_RX_PIN + #define Z_SERIAL_RX_PIN 65 + #endif + #ifndef Z2_SERIAL_TX_PIN + #define Z2_SERIAL_TX_PIN -1 + #endif + #ifndef Z2_SERIAL_RX_PIN + #define Z2_SERIAL_RX_PIN -1 + #endif - #define E0_SERIAL_TX_PIN 44 - #define E0_SERIAL_RX_PIN 66 - #define E1_SERIAL_TX_PIN -1 - #define E1_SERIAL_RX_PIN -1 - #define E2_SERIAL_TX_PIN -1 - #define E2_SERIAL_RX_PIN -1 - #define E3_SERIAL_TX_PIN -1 - #define E3_SERIAL_RX_PIN -1 - #define E4_SERIAL_TX_PIN -1 - #define E4_SERIAL_RX_PIN -1 + #ifndef E0_SERIAL_TX_PIN + #define E0_SERIAL_TX_PIN 44 + #endif + #ifndef E0_SERIAL_RX_PIN + #define E0_SERIAL_RX_PIN 66 + #endif + #ifndef E1_SERIAL_TX_PIN + #define E1_SERIAL_TX_PIN -1 + #endif + #ifndef E1_SERIAL_RX_PIN + #define E1_SERIAL_RX_PIN -1 + #endif + #ifndef E2_SERIAL_TX_PIN + #define E2_SERIAL_TX_PIN -1 + #endif + #ifndef E2_SERIAL_RX_PIN + #define E2_SERIAL_RX_PIN -1 + #endif + #ifndef E3_SERIAL_TX_PIN + #define E3_SERIAL_TX_PIN -1 + #endif + #ifndef E3_SERIAL_RX_PIN + #define E3_SERIAL_RX_PIN -1 + #endif + #ifndef E4_SERIAL_TX_PIN + #define E4_SERIAL_TX_PIN -1 + #endif + #ifndef E4_SERIAL_RX_PIN + #define E4_SERIAL_RX_PIN -1 + #endif #endif // @@ -615,7 +661,7 @@ // Beeper on AUX-4 #define BEEPER_PIN 33 - // Buttons are directly attached using AUX-2 + // Buttons are directly attached to AUX-2 #if ENABLED(REPRAPWORLD_KEYPAD) #define SHIFT_OUT 40 #define SHIFT_CLK 44 diff --git a/Marlin/src/pins/pins_RAMPS_13.h b/Marlin/src/pins/ramps/pins_RAMPS_13.h similarity index 100% rename from Marlin/src/pins/pins_RAMPS_13.h rename to Marlin/src/pins/ramps/pins_RAMPS_13.h diff --git a/Marlin/src/pins/pins_RAMPS_CREALITY.h b/Marlin/src/pins/ramps/pins_RAMPS_CREALITY.h similarity index 100% rename from Marlin/src/pins/pins_RAMPS_CREALITY.h rename to Marlin/src/pins/ramps/pins_RAMPS_CREALITY.h diff --git a/Marlin/src/pins/pins_RAMPS_DAGOMA.h b/Marlin/src/pins/ramps/pins_RAMPS_DAGOMA.h similarity index 100% rename from Marlin/src/pins/pins_RAMPS_DAGOMA.h rename to Marlin/src/pins/ramps/pins_RAMPS_DAGOMA.h diff --git a/Marlin/src/pins/pins_RAMPS_ENDER_4.h b/Marlin/src/pins/ramps/pins_RAMPS_ENDER_4.h similarity index 100% rename from Marlin/src/pins/pins_RAMPS_ENDER_4.h rename to Marlin/src/pins/ramps/pins_RAMPS_ENDER_4.h diff --git a/Marlin/src/pins/pins_RAMPS_OLD.h b/Marlin/src/pins/ramps/pins_RAMPS_OLD.h similarity index 84% rename from Marlin/src/pins/pins_RAMPS_OLD.h rename to Marlin/src/pins/ramps/pins_RAMPS_OLD.h index f0deec3b04..13a2d9dee4 100644 --- a/Marlin/src/pins/pins_RAMPS_OLD.h +++ b/Marlin/src/pins/ramps/pins_RAMPS_OLD.h @@ -78,9 +78,9 @@ // SPI for Max6675 or Max31855 Thermocouple #if DISABLED(SDSUPPORT) - #define MAX6675_SS_PIN 66 // Do not use pin 53 if there is even the remote possibility of using Display/SD card + #define MAX6675_SS_PIN 66 // Don't use 53 if there is even the remote possibility of using Display/SD card #else - #define MAX6675_SS_PIN 66 // Do not use pin 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present + #define MAX6675_SS_PIN 66 // Don't use 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present #endif // @@ -103,14 +103,14 @@ // // Misc. Functions // -#define SDPOWER 48 +#define SDPOWER_PIN 48 #define SDSS 53 #define LED_PIN 13 -#define CASE_LIGHT_PIN 45 // MUST BE HARDWARE PWM +#define CASE_LIGHT_PIN 45 // Hardware PWM // // M3/M4/M5 - Spindle/Laser Control // -#define SPINDLE_LASER_ENA_PIN 41 // Pin should have a pullup/pulldown! -#define SPINDLE_LASER_PWM_PIN 45 // MUST BE HARDWARE PWM +#define SPINDLE_LASER_ENA_PIN 41 // Pullup or pulldown! +#define SPINDLE_LASER_PWM_PIN 45 // Hardware PWM #define SPINDLE_DIR_PIN 43 diff --git a/Marlin/src/pins/pins_RAMPS_PLUS.h b/Marlin/src/pins/ramps/pins_RAMPS_PLUS.h similarity index 100% rename from Marlin/src/pins/pins_RAMPS_PLUS.h rename to Marlin/src/pins/ramps/pins_RAMPS_PLUS.h diff --git a/Marlin/src/pins/pins_RIGIDBOARD.h b/Marlin/src/pins/ramps/pins_RIGIDBOARD.h similarity index 98% rename from Marlin/src/pins/pins_RIGIDBOARD.h rename to Marlin/src/pins/ramps/pins_RIGIDBOARD.h index 4b472b652d..f4b38d630a 100644 --- a/Marlin/src/pins/pins_RIGIDBOARD.h +++ b/Marlin/src/pins/ramps/pins_RIGIDBOARD.h @@ -25,7 +25,9 @@ * RIGIDBOARD Arduino Mega with RAMPS v1.4 pin assignments */ -#define BOARD_NAME "RigidBoard" +#ifndef BOARD_NAME + #define BOARD_NAME "RigidBoard" +#endif // // Z Probe (when not Z_MIN_PIN) diff --git a/Marlin/src/pins/pins_RIGIDBOARD_V2.h b/Marlin/src/pins/ramps/pins_RIGIDBOARD_V2.h similarity index 99% rename from Marlin/src/pins/pins_RIGIDBOARD_V2.h rename to Marlin/src/pins/ramps/pins_RIGIDBOARD_V2.h index 419726883e..b9ccd45f13 100644 --- a/Marlin/src/pins/pins_RIGIDBOARD_V2.h +++ b/Marlin/src/pins/ramps/pins_RIGIDBOARD_V2.h @@ -25,11 +25,10 @@ * RIGIDBOARD V2 Arduino Mega with RAMPS v1.4 pin assignments */ -#include "pins_RIGIDBOARD.h" - -#undef BOARD_NAME #define BOARD_NAME "RigidBoard V2" +#include "pins_RIGIDBOARD.h" + // // Steppers // diff --git a/Marlin/src/pins/pins_RL200.h b/Marlin/src/pins/ramps/pins_RL200.h similarity index 100% rename from Marlin/src/pins/pins_RL200.h rename to Marlin/src/pins/ramps/pins_RL200.h index af03ee8c4a..381b882e96 100644 --- a/Marlin/src/pins/pins_RL200.h +++ b/Marlin/src/pins/ramps/pins_RL200.h @@ -26,8 +26,8 @@ * extruder motors due to dual Z motors. Pinout therefore based on pins_RUMBA.h. */ -#define DEFAULT_MACHINE_NAME "Rapide Lite 200" #define BOARD_NAME "RL200" +#define DEFAULT_MACHINE_NAME "Rapide Lite 200" #if HOTENDS > 2 || E_STEPPERS > 2 #error "RL200v1 supports up to 2 hotends / E-steppers. Comment out this line to continue." diff --git a/Marlin/src/pins/pins_RUMBA.h b/Marlin/src/pins/ramps/pins_RUMBA.h similarity index 95% rename from Marlin/src/pins/pins_RUMBA.h rename to Marlin/src/pins/ramps/pins_RUMBA.h index db3dff3c74..0f8ea6ee96 100644 --- a/Marlin/src/pins/pins_RUMBA.h +++ b/Marlin/src/pins/ramps/pins_RUMBA.h @@ -27,18 +27,16 @@ #ifndef __AVR_ATmega2560__ #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'" -#endif - -#if HOTENDS > 3 || E_STEPPERS > 3 +#elif HOTENDS > 3 || E_STEPPERS > 3 #error "RUMBA supports up to 3 hotends / E-steppers. Comment out this line to continue." #endif -#ifndef DEFAULT_MACHINE_NAME - #define DEFAULT_MACHINE_NAME "Rumba" -#endif #ifndef BOARD_NAME #define BOARD_NAME "Rumba" #endif +#ifndef DEFAULT_MACHINE_NAME + #define DEFAULT_MACHINE_NAME BOARD_NAME +#endif // // Servos @@ -156,10 +154,10 @@ // M3/M4/M5 - Spindle/Laser Control // #ifndef SPINDLE_LASER_PWM_PIN - #define SPINDLE_LASER_PWM_PIN 4 // MUST BE HARDWARE PWM. Pin 4 interrupts OC0* and OC1* always in use? + #define SPINDLE_LASER_PWM_PIN 4 // Hardware PWM. Pin 4 interrupts OC0* and OC1* always in use? #endif #ifndef SPINDLE_LASER_ENA_PIN - #define SPINDLE_LASER_ENA_PIN 14 // Pin should have a pullup! + #define SPINDLE_LASER_ENA_PIN 14 // Pullup! #endif #ifndef SPINDLE_DIR_PIN #define SPINDLE_DIR_PIN 15 @@ -217,7 +215,6 @@ #define BEEPER_PIN 44 #if ENABLED(SDSUPPORT) - #define SDPOWER -1 #define SDSS 53 #define SD_DETECT_PIN 49 #endif diff --git a/Marlin/src/pins/pins_RUMBA_RAISE3D.h b/Marlin/src/pins/ramps/pins_RUMBA_RAISE3D.h similarity index 100% rename from Marlin/src/pins/pins_RUMBA_RAISE3D.h rename to Marlin/src/pins/ramps/pins_RUMBA_RAISE3D.h index 8d5297c1b8..d04695e292 100644 --- a/Marlin/src/pins/pins_RUMBA_RAISE3D.h +++ b/Marlin/src/pins/ramps/pins_RUMBA_RAISE3D.h @@ -21,8 +21,8 @@ */ #pragma once -#define DEFAULT_MACHINE_NAME "Raise3D N Series" #define BOARD_NAME "Raise3D Rumba" +#define DEFAULT_MACHINE_NAME "Raise3D N Series" // Raise3D uses thermocouples on the standard input pins #define TEMP_0_PIN 15 // Analog Input diff --git a/Marlin/src/pins/pins_SAINSMART_2IN1.h b/Marlin/src/pins/ramps/pins_SAINSMART_2IN1.h similarity index 100% rename from Marlin/src/pins/pins_SAINSMART_2IN1.h rename to Marlin/src/pins/ramps/pins_SAINSMART_2IN1.h diff --git a/Marlin/src/pins/pins_TRIGORILLA_13.h b/Marlin/src/pins/ramps/pins_TRIGORILLA_13.h similarity index 100% rename from Marlin/src/pins/pins_TRIGORILLA_13.h rename to Marlin/src/pins/ramps/pins_TRIGORILLA_13.h diff --git a/Marlin/src/pins/pins_TRIGORILLA_14.h b/Marlin/src/pins/ramps/pins_TRIGORILLA_14.h similarity index 100% rename from Marlin/src/pins/pins_TRIGORILLA_14.h rename to Marlin/src/pins/ramps/pins_TRIGORILLA_14.h diff --git a/Marlin/src/pins/pins_TRONXY_V3_1_0.h b/Marlin/src/pins/ramps/pins_TRONXY_V3_1_0.h similarity index 99% rename from Marlin/src/pins/pins_TRONXY_V3_1_0.h rename to Marlin/src/pins/ramps/pins_TRONXY_V3_1_0.h index aaf276da78..a1202213e7 100644 --- a/Marlin/src/pins/pins_TRONXY_V3_1_0.h +++ b/Marlin/src/pins/ramps/pins_TRONXY_V3_1_0.h @@ -27,9 +27,7 @@ #ifndef __AVR_ATmega2560__ #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'" -#endif - -#if HOTENDS > 2 || E_STEPPERS > 2 +#elif HOTENDS > 2 || E_STEPPERS > 2 #error "TRONXY-V3-1.0 supports only 2 hotends/E-steppers. Comment out this line to continue." #endif diff --git a/Marlin/src/pins/ramps/pins_TT_OSCAR.h b/Marlin/src/pins/ramps/pins_TT_OSCAR.h new file mode 100644 index 0000000000..edc326fe9d --- /dev/null +++ b/Marlin/src/pins/ramps/pins_TT_OSCAR.h @@ -0,0 +1,512 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + +#if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__) + #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'" +#endif + +#if HOTENDS > 5 || E_STEPPERS > 5 + #error "TTOSCAR supports up to 5 hotends / E-steppers. Comment out this line to continue." +#endif + +#define BOARD_NAME "TT OSCAR" +#define DEFAULT_MACHINE_NAME BOARD_NAME + +// +// Servos +// +#define SERVO0_PIN 11 +#define SERVO1_PIN 12 +#define SERVO2_PIN 5 +#define SERVO3_PIN 4 + +// +// Limit Switches +// +#define X_MIN_PIN 3 +#define X_MAX_PIN 2 +#define Y_MIN_PIN 14 +#define Y_MAX_PIN 15 +#define Z_MIN_PIN 18 +#define Z_MAX_PIN 19 + +// +// Z Probe (when not Z_MIN_PIN) +// +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN SERVO3_PIN +#endif + +// +// Steppers +// +#define X_STEP_PIN 54 +#define X_DIR_PIN 55 +#define X_ENABLE_PIN 38 +#define X_CS_PIN 57 + +#define Y_STEP_PIN 60 +#define Y_DIR_PIN 61 +#define Y_ENABLE_PIN 56 +#define Y_CS_PIN 58 + +#define Z_STEP_PIN 46 +#define Z_DIR_PIN 48 +#define Z_ENABLE_PIN 62 +#define Z_CS_PIN 53 + +#define E0_STEP_PIN 26 +#define E0_DIR_PIN 28 +#define E0_ENABLE_PIN 24 +#define E0_CS_PIN 49 + +#define E1_STEP_PIN 36 +#define E1_DIR_PIN 34 +#define E1_ENABLE_PIN 30 +#define E1_CS_PIN E0_CS_PIN + +#define E2_STEP_PIN 63 +#define E2_DIR_PIN 22 +#define E2_ENABLE_PIN 59 +#define E2_CS_PIN E0_CS_PIN + +#define E3_STEP_PIN 32 +#define E3_DIR_PIN 40 +#define E3_ENABLE_PIN 39 +#define E3_CS_PIN E0_CS_PIN + +#define E4_STEP_PIN 43 +#define E4_DIR_PIN 42 +#define E4_ENABLE_PIN 47 +#define E4_CS_PIN E0_CS_PIN + +#if HAS_TMC220x + /** + * TMC2208/TMC2209 stepper drivers + * + * Hardware serial communication ports. + * If undefined software serial is used according to the pins below + */ + //#define X_HARDWARE_SERIAL Serial1 + //#define X2_HARDWARE_SERIAL Serial1 + //#define Y_HARDWARE_SERIAL Serial1 + //#define Y2_HARDWARE_SERIAL Serial1 + //#define Z_HARDWARE_SERIAL Serial1 + //#define Z2_HARDWARE_SERIAL Serial1 + //#define E0_HARDWARE_SERIAL Serial1 + //#define E1_HARDWARE_SERIAL Serial1 + //#define E2_HARDWARE_SERIAL Serial1 + //#define E3_HARDWARE_SERIAL Serial1 + //#define E3_HARDWARE_SERIAL Serial1 + + // + // Software serial + // + + #define X_SERIAL_TX_PIN -1 // 59 + #define X_SERIAL_RX_PIN -1 // 63 + #define X2_SERIAL_TX_PIN -1 + #define X2_SERIAL_RX_PIN -1 + + #define Y_SERIAL_TX_PIN -1 // 64 + #define Y_SERIAL_RX_PIN -1 // 40 + #define Y2_SERIAL_TX_PIN -1 + #define Y2_SERIAL_RX_PIN -1 + + #define Z_SERIAL_TX_PIN -1 // 44 + #define Z_SERIAL_RX_PIN -1 // 42 + #define Z2_SERIAL_TX_PIN -1 + #define Z2_SERIAL_RX_PIN -1 + + #define E0_SERIAL_TX_PIN -1 // 66 + #define E0_SERIAL_RX_PIN -1 // 65 + #define E1_SERIAL_TX_PIN -1 + #define E1_SERIAL_RX_PIN -1 + #define E2_SERIAL_TX_PIN -1 + #define E2_SERIAL_RX_PIN -1 + #define E3_SERIAL_TX_PIN -1 + #define E3_SERIAL_RX_PIN -1 + #define E4_SERIAL_TX_PIN -1 + #define E4_SERIAL_RX_PIN -1 +#endif + +// +// Default pins for TMC software SPI +// +//#if ENABLED(TMC_USE_SW_SPI) +// #ifndef TMC_SW_MOSI +// #define TMC_SW_MOSI 66 +// #endif +// #ifndef TMC_SW_MISO +// #define TMC_SW_MISO 44 +// #endif +// #ifndef TMC_SW_SCK +// #define TMC_SW_SCK 64 +// #endif +//#endif + +// +// Temperature Sensors +// +#define TEMP_0_PIN 13 +#define TEMP_1_PIN 15 +#define TEMP_2_PIN 10 +#define TEMP_3_PIN 11 +#define TEMP_BED_PIN 14 + +#if TEMP_SENSOR_CHAMBER > 0 + #define TEMP_CHAMBER_PIN 12 +#else + #define TEMP_4_PIN 12 +#endif + +// SPI for Max6675 or Max31855 Thermocouple +//#if DISABLED(SDSUPPORT) +// #define MAX6675_SS 66 // Don't use 53 if there is even the remote possibility of using Display/SD card +//#else +// #define MAX6675_SS 66 // Don't use 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present +//#endif + +// +// Heaters / Fans +// +#define HEATER_0_PIN 10 +#define HEATER_1_PIN 7 +#define HEATER_2_PIN 44 +#define HEATER_BED_PIN 8 + +#define FAN_PIN 9 + +#if EXTRUDERS >= 5 + #define HEATER_4_PIN 6 +#else + #define FAN1_PIN 6 +#endif + +#if EXTRUDERS >= 4 + #define HEATER_3_PIN 45 +#else + #define FAN2_PIN 45 +#endif + +// +// Misc. Functions +// +#define SDSS 53 +#define LED_PIN 13 + +//#ifndef FILWIDTH_PIN +// #define FILWIDTH_PIN 5 // Analog Input +//#endif + +// DIO 4 (Servos plug) for the runout sensor. +//#define FIL_RUNOUT_PIN SERVO3_PIN + +#ifndef PS_ON_PIN + #define PS_ON_PIN 12 +#endif + +// +// Case Light +// +#if ENABLED(CASE_LIGHT_ENABLE) && !PIN_EXISTS(CASE_LIGHT) && !defined(SPINDLE_LASER_ENABLE_PIN) + #if !NUM_SERVOS // Prefer the servo connector + #define CASE_LIGHT_PIN 6 // Hardware PWM + #elif HAS_FREE_AUX2_PINS // Try to use AUX 2 + #define CASE_LIGHT_PIN 44 // Hardware PWM + #endif +#endif + +// +// M3/M4/M5 - Spindle/Laser Control +// +#if ENABLED(SPINDLE_LASER_ENABLE) && !PIN_EXISTS(SPINDLE_LASER_ENABLE) + #if !NUM_SERVOS // Prefer the servo connector + #define SPINDLE_LASER_ENABLE_PIN 4 // Pullup or pulldown! + #define SPINDLE_LASER_PWM_PIN 6 // Hardware PWM + #define SPINDLE_DIR_PIN 5 + #elif HAS_FREE_AUX2_PINS // Try to use AUX 2 + #define SPINDLE_LASER_ENABLE_PIN 40 // Pullup or pulldown! + #define SPINDLE_LASER_PWM_PIN 44 // Hardware PWM + #define SPINDLE_DIR_PIN 65 + #endif +#endif + +// +// Průša i3 MK2 Multiplexer Support +// +//#ifndef E_MUX0_PIN +// #define E_MUX0_PIN 58 // Y_CS_PIN +//#endif +//#ifndef E_MUX1_PIN +// #define E_MUX1_PIN 53 // Z_CS_PIN +//#endif +//#ifndef E_MUX2_PIN +// #define E_MUX2_PIN 49 // En_CS_PIN +//#endif + +////////////////////////// +// LCDs and Controllers // +////////////////////////// + +#if HAS_SPI_LCD + + // + // LCD Display output pins + // + #if ENABLED(REPRAPWORLD_GRAPHICAL_LCD) + + #define LCD_PINS_RS 49 // CS chip select /SS chip slave select + #define LCD_PINS_ENABLE 51 // SID (MOSI) + #define LCD_PINS_D4 52 // SCK (CLK) clock + + #elif BOTH(NEWPANEL, PANEL_ONE) + + #define LCD_PINS_RS 40 + #define LCD_PINS_ENABLE 42 + #define LCD_PINS_D4 65 + #define LCD_PINS_D5 66 + #define LCD_PINS_D6 44 + #define LCD_PINS_D7 64 + + #elif ENABLED(ZONESTAR_LCD) + + #define LCD_PINS_RS 64 + #define LCD_PINS_ENABLE 44 + #define LCD_PINS_D4 63 + #define LCD_PINS_D5 40 + #define LCD_PINS_D6 42 + #define LCD_PINS_D7 65 + #define ADC_KEYPAD_PIN 12 + + #else + + #if ENABLED(CR10_STOCKDISPLAY) + + #define LCD_PINS_RS 27 + #define LCD_PINS_ENABLE 29 + #define LCD_PINS_D4 25 + + #if DISABLED(NEWPANEL) + #define BEEPER_PIN 37 + #endif + + #else + + #if EITHER(MKS_12864OLED, MKS_12864OLED_SSD1306) + #define LCD_PINS_DC 25 // Set as output on init + #define LCD_PINS_RS 27 // Pull low for 1s to init + // DOGM SPI LCD Support + #define DOGLCD_CS 16 + #define DOGLCD_MOSI 17 + #define DOGLCD_SCK 23 + #define DOGLCD_A0 LCD_PINS_DC + #else + #define LCD_PINS_RS 16 + #define LCD_PINS_ENABLE 17 + #define LCD_PINS_D4 23 + #define LCD_PINS_D5 25 + #define LCD_PINS_D6 27 + #endif + + #define LCD_PINS_D7 29 + + #if DISABLED(NEWPANEL) + #define BEEPER_PIN 33 + #endif + + #endif + + #if DISABLED(NEWPANEL) + // Buttons are attached to a shift register + // Not wired yet + //#define SHIFT_CLK 38 + //#define SHIFT_LD 42 + //#define SHIFT_OUT 40 + //#define SHIFT_EN 17 + #endif + + #endif + + // + // LCD Display input pins + // + #if ENABLED(NEWPANEL) + + #if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) + + #define BEEPER_PIN 37 + + #if ENABLED(CR10_STOCKDISPLAY) + #define BTN_EN1 17 + #define BTN_EN2 23 + #else + #define BTN_EN1 31 + #define BTN_EN2 33 + #endif + + #define BTN_ENC 35 + #define SD_DETECT_PIN 49 + //#define KILL_PIN 41 + + #if ENABLED(BQ_LCD_SMART_CONTROLLER) + #define LCD_BACKLIGHT_PIN 39 + #endif + + #elif ENABLED(REPRAPWORLD_GRAPHICAL_LCD) + + #define BTN_EN1 64 + #define BTN_EN2 59 + #define BTN_ENC 63 + #define SD_DETECT_PIN 42 + + #elif ENABLED(LCD_I2C_PANELOLU2) + + #define BTN_EN1 47 + #define BTN_EN2 43 + #define BTN_ENC 32 + #define LCD_SDSS 53 + //#define KILL_PIN 41 + + #elif ENABLED(LCD_I2C_VIKI) + + #define BTN_EN1 22 // http://files.panucatt.com/datasheets/viki_wiring_diagram.pdf explains 40/42. + #define BTN_EN2 7 // 22/7 are unused on RAMPS_14. 22 is unused and 7 the SERVO0_PIN on RAMPS_13. + #define BTN_ENC -1 + + #define LCD_SDSS 53 + #define SD_DETECT_PIN 49 + + #elif EITHER(VIKI2, miniVIKI) + + #define DOGLCD_CS 45 + #define DOGLCD_A0 44 + #define LCD_SCREEN_ROT_180 + + #define BEEPER_PIN 33 + #define STAT_LED_RED_PIN 32 + #define STAT_LED_BLUE_PIN 35 + + #define BTN_EN1 22 + #define BTN_EN2 7 + #define BTN_ENC 39 + + #define SDSS 53 + #define SD_DETECT_PIN -1 // Pin 49 for display SD interface, 72 for easy adapter board + //#define KILL_PIN 31 + + #elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER) + + #define DOGLCD_CS 29 + #define DOGLCD_A0 27 + + #define BEEPER_PIN 23 + #define LCD_BACKLIGHT_PIN 33 + + #define BTN_EN1 35 + #define BTN_EN2 37 + #define BTN_ENC 31 + + #define LCD_SDSS 53 + #define SD_DETECT_PIN 49 + //#define KILL_PIN 41 + + #elif ENABLED(MKS_MINI_12864) + + #define DOGLCD_A0 27 + #define DOGLCD_CS 25 + + // GLCD features + //#define LCD_CONTRAST 190 + // Uncomment screen orientation + //#define LCD_SCREEN_ROT_90 + //#define LCD_SCREEN_ROT_180 + //#define LCD_SCREEN_ROT_270 + + #define BEEPER_PIN 37 + + #define LCD_BACKLIGHT_PIN 65 // backlight LED on A11/D65 + + #define BTN_EN1 31 + #define BTN_EN2 33 + #define BTN_ENC 35 + //#define SDSS 53 + #define SD_DETECT_PIN 49 + //#define KILL_PIN 64 + + #elif ENABLED(MINIPANEL) + + #define BEEPER_PIN 42 + // not connected to a pin + #define LCD_BACKLIGHT_PIN 65 // backlight LED on A11/D65 + + #define DOGLCD_A0 44 + #define DOGLCD_CS 66 + + // GLCD features + //#define LCD_CONTRAST 190 + // Uncomment screen orientation + //#define LCD_SCREEN_ROT_90 + //#define LCD_SCREEN_ROT_180 + //#define LCD_SCREEN_ROT_270 + + #define BTN_EN1 40 + #define BTN_EN2 63 + #define BTN_ENC 59 + + #define SDSS 53 + #define SD_DETECT_PIN 49 + //#define KILL_PIN 64 + + #else + + // Beeper on AUX-4 + #define BEEPER_PIN 33 + + // Buttons are directly attached to AUX-2 + #if ENABLED(REPRAPWORLD_KEYPAD) + #define SHIFT_OUT 40 + #define SHIFT_CLK 44 + #define SHIFT_LD 42 + #define BTN_EN1 64 + #define BTN_EN2 59 + #define BTN_ENC 63 + #elif ENABLED(PANEL_ONE) + #define BTN_EN1 59 // AUX2 PIN 3 + #define BTN_EN2 63 // AUX2 PIN 4 + #define BTN_ENC 49 // AUX3 PIN 7 + #else + #define BTN_EN1 37 + #define BTN_EN2 35 + #define BTN_ENC 31 + #endif + + #if ENABLED(G3D_PANEL) + #define SD_DETECT_PIN 49 + //#define KILL_PIN 41 + #endif + + #endif + + #endif // NEWPANEL + +#endif diff --git a/Marlin/src/pins/pins_ULTIMAIN_2.h b/Marlin/src/pins/ramps/pins_ULTIMAIN_2.h similarity index 96% rename from Marlin/src/pins/pins_ULTIMAIN_2.h rename to Marlin/src/pins/ramps/pins_ULTIMAIN_2.h index f61f16c2f4..da1eecbdb1 100644 --- a/Marlin/src/pins/pins_ULTIMAIN_2.h +++ b/Marlin/src/pins/ramps/pins_ULTIMAIN_2.h @@ -37,9 +37,9 @@ #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'" #endif +#define BOARD_NAME "Ultimaker 2.x" #define DEFAULT_MACHINE_NAME "Ultimaker" #define DEFAULT_SOURCE_CODE_URL "https://github.com/Ultimaker/Marlin" -#define BOARD_NAME "Ultimaker 2.x" // // Limit Switches @@ -132,8 +132,8 @@ #if HAS_CUTTER // use the LED_PIN for spindle speed control or case light #undef LED_PIN #define SPINDLE_DIR_PIN 16 - #define SPINDLE_LASER_ENA_PIN 17 // Pin should have a pullup! - #define SPINDLE_LASER_PWM_PIN 8 // MUST BE HARDWARE PWM + #define SPINDLE_LASER_ENA_PIN 17 // Pullup! + #define SPINDLE_LASER_PWM_PIN 8 // Hardware PWM #else #undef LED_PIN #define CASE_LIGHT_PIN 8 diff --git a/Marlin/src/pins/pins_ULTIMAKER.h b/Marlin/src/pins/ramps/pins_ULTIMAKER.h similarity index 95% rename from Marlin/src/pins/pins_ULTIMAKER.h rename to Marlin/src/pins/ramps/pins_ULTIMAKER.h index d895058989..f6239ae163 100644 --- a/Marlin/src/pins/pins_ULTIMAKER.h +++ b/Marlin/src/pins/ramps/pins_ULTIMAKER.h @@ -37,9 +37,9 @@ #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'" #endif -#define DEFAULT_MACHINE_NAME "Ultimaker" -#define DEFAULT_SOURCE_CODE_URL "https://github.com/Ultimaker/Marlin" #define BOARD_NAME "Ultimaker" +#define DEFAULT_MACHINE_NAME BOARD_NAME +#define DEFAULT_SOURCE_CODE_URL "https://github.com/Ultimaker/Marlin" // // Servos @@ -160,6 +160,6 @@ // // M3/M4/M5 - Spindle/Laser Control // -#define SPINDLE_LASER_PWM_PIN 9 // MUST BE HARDWARE PWM -#define SPINDLE_LASER_ENA_PIN 10 // Pin should have a pullup! +#define SPINDLE_LASER_PWM_PIN 9 // Hardware PWM +#define SPINDLE_LASER_ENA_PIN 10 // Pullup! #define SPINDLE_DIR_PIN 11 // use the EXP3 PWM header diff --git a/Marlin/src/pins/pins_ULTIMAKER_OLD.h b/Marlin/src/pins/ramps/pins_ULTIMAKER_OLD.h similarity index 93% rename from Marlin/src/pins/pins_ULTIMAKER_OLD.h rename to Marlin/src/pins/ramps/pins_ULTIMAKER_OLD.h index f0c048f5ab..6a25b509e3 100644 --- a/Marlin/src/pins/pins_ULTIMAKER_OLD.h +++ b/Marlin/src/pins/ramps/pins_ULTIMAKER_OLD.h @@ -64,9 +64,17 @@ #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'" #endif +#ifdef BOARD_REV_1_1_TO_1_3 + #define BOARD_NAME "Ultimaker 1.1-1.3" +#elif defined(BOARD_REV_1_0) + #define BOARD_NAME "Ultimaker 1.0" +#elif defined(BOARD_REV_1_5) + #define BOARD_NAME "Ultimaker 1.5" +#else + #define BOARD_NAME "Ultimaker 1.5.4+" +#endif #define DEFAULT_MACHINE_NAME "Ultimaker" #define DEFAULT_SOURCE_CODE_URL "https://github.com/Ultimaker/Marlin" -#define BOARD_NAME "Ultimaker <1.5.4" // // Limit Switches @@ -234,13 +242,13 @@ */ #if EXTRUDERS == 1 #define SPINDLE_DIR_PIN 43 - #define SPINDLE_LASER_PWM_PIN 45 // MUST BE HARDWARE PWM - #define SPINDLE_LASER_ENA_PIN 41 // Pin should have a pullup! + #define SPINDLE_LASER_PWM_PIN 45 // Hardware PWM + #define SPINDLE_LASER_ENA_PIN 41 // Pullup! #elif TEMP_SENSOR_BED == 0 // Can't use E0 so see if HEATER_BED_PIN is available #undef HEATER_BED_PIN #define SPINDLE_DIR_PIN 38 // Probably pin 4 on 10 pin connector closest to the E0 socket - #define SPINDLE_LASER_PWM_PIN 4 // MUST BE HARDWARE PWM - Special precautions usually needed. - #define SPINDLE_LASER_ENA_PIN 40 // Pin should have a pullup! (Probably pin 6 on the 10-pin + #define SPINDLE_LASER_PWM_PIN 4 // Hardware PWM - Special precautions usually needed. + #define SPINDLE_LASER_ENA_PIN 40 // Pullup! (Probably pin 6 on the 10-pin // connector closest to the E0 socket) #endif #endif diff --git a/Marlin/src/pins/pins_VORON.h b/Marlin/src/pins/ramps/pins_VORON.h similarity index 100% rename from Marlin/src/pins/pins_VORON.h rename to Marlin/src/pins/ramps/pins_VORON.h diff --git a/Marlin/src/pins/pins_ZRIB_V20.h b/Marlin/src/pins/ramps/pins_ZRIB_V20.h similarity index 100% rename from Marlin/src/pins/pins_ZRIB_V20.h rename to Marlin/src/pins/ramps/pins_ZRIB_V20.h diff --git a/Marlin/src/pins/pins_Z_BOLT_X_SERIES.h b/Marlin/src/pins/ramps/pins_Z_BOLT_X_SERIES.h similarity index 68% rename from Marlin/src/pins/pins_Z_BOLT_X_SERIES.h rename to Marlin/src/pins/ramps/pins_Z_BOLT_X_SERIES.h index 89f8df4b4d..de1899e7ff 100644 --- a/Marlin/src/pins/pins_Z_BOLT_X_SERIES.h +++ b/Marlin/src/pins/ramps/pins_Z_BOLT_X_SERIES.h @@ -25,24 +25,14 @@ * Z-Bolt X Series board – based on Arduino Mega2560 */ -#if HOTENDS > 4 || E_STEPPERS > 4 +#if !defined(__AVR_ATmega2560__) + #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'" +#elif HOTENDS > 4 || E_STEPPERS > 4 #error "Z-Bolt X Series board supports up to 4 hotends / E-steppers." #endif #define BOARD_NAME "Z-Bolt X Series" -#if ENABLED(TARGET_LPC1768) - #error "Oops! Set MOTHERBOARD to an LPC1768-based board when building for LPC1768." -#elif defined(__STM32F1__) - #error "Oops! Set MOTHERBOARD to an STM32F1-based board when building for STM32F1." -#endif - -#if DISABLED(IS_RAMPS_SMART, IS_RAMPS_DUO, IS_RAMPS4DUE, TARGET_LPC1768) - #if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__) - #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'" - #endif -#endif - // // Servos // @@ -165,13 +155,11 @@ #define PS_ON_PIN 12 #endif -#define AUX2_PINS_FREE !( BOTH(ULTRA_LCD, NEWPANEL) && ANY(PANEL_ONE, VIKI2, miniVIKI, MINIPANEL, REPRAPWORLD_KEYPAD) ) - #if ENABLED(CASE_LIGHT_ENABLE) && !defined(CASE_LIGHT_PIN) && !defined(SPINDLE_LASER_ENA_PIN) - #if NUM_SERVOS <= 1 // try to use servo connector first - #define CASE_LIGHT_PIN 6 // MUST BE HARDWARE PWM - #elif AUX2_PINS_FREE - #define CASE_LIGHT_PIN 44 // MUST BE HARDWARE PWM + #if NUM_SERVOS <= 1 // Prefer the servo connector + #define CASE_LIGHT_PIN 6 // Hardware PWM + #elif HAS_FREE_AUX2_PINS + #define CASE_LIGHT_PIN 44 // Hardware PWM #endif #endif @@ -179,19 +167,17 @@ // M3/M4/M5 - Spindle/Laser Control // #if HAS_CUTTER && !PIN_EXISTS(SPINDLE_LASER_ENA) - #if !defined(NUM_SERVOS) || NUM_SERVOS == 0 // try to use servo connector first - #define SPINDLE_LASER_ENA_PIN 4 // Pin should have a pullup/pulldown! - #define SPINDLE_LASER_PWM_PIN 6 // MUST BE HARDWARE PWM + #if !defined(NUM_SERVOS) || NUM_SERVOS == 0 // Prefer the servo connector + #define SPINDLE_LASER_ENA_PIN 4 // Pullup or pulldown! + #define SPINDLE_LASER_PWM_PIN 6 // Hardware PWM #define SPINDLE_DIR_PIN 5 - #elif AUX2_PINS_FREE - #define SPINDLE_LASER_ENA_PIN 40 // Pin should have a pullup/pulldown! - #define SPINDLE_LASER_PWM_PIN 44 // MUST BE HARDWARE PWM + #elif HAS_FREE_AUX2_PINS + #define SPINDLE_LASER_ENA_PIN 40 // Pullup or pulldown! + #define SPINDLE_LASER_PWM_PIN 44 // Hardware PWM #define SPINDLE_DIR_PIN 65 #endif #endif -#undef AUX2_PINS_FREE - // // TMC software SPI // @@ -230,29 +216,73 @@ // Software serial // - #define X_SERIAL_TX_PIN 40 - #define X_SERIAL_RX_PIN 63 - #define X2_SERIAL_TX_PIN -1 - #define X2_SERIAL_RX_PIN -1 + #ifndef X_SERIAL_TX_PIN + #define X_SERIAL_TX_PIN 40 + #endif + #ifndef X_SERIAL_RX_PIN + #define X_SERIAL_RX_PIN 63 + #endif + #ifndef X2_SERIAL_TX_PIN + #define X2_SERIAL_TX_PIN -1 + #endif + #ifndef X2_SERIAL_RX_PIN + #define X2_SERIAL_RX_PIN -1 + #endif - #define Y_SERIAL_TX_PIN 59 - #define Y_SERIAL_RX_PIN 64 - #define Y2_SERIAL_TX_PIN -1 - #define Y2_SERIAL_RX_PIN -1 + #ifndef Y_SERIAL_TX_PIN + #define Y_SERIAL_TX_PIN 59 + #endif + #ifndef Y_SERIAL_RX_PIN + #define Y_SERIAL_RX_PIN 64 + #endif + #ifndef Y2_SERIAL_TX_PIN + #define Y2_SERIAL_TX_PIN -1 + #endif + #ifndef Y2_SERIAL_RX_PIN + #define Y2_SERIAL_RX_PIN -1 + #endif - #define Z_SERIAL_TX_PIN 42 - #define Z_SERIAL_RX_PIN 65 - #define Z2_SERIAL_TX_PIN -1 - #define Z2_SERIAL_RX_PIN -1 + #ifndef Z_SERIAL_TX_PIN + #define Z_SERIAL_TX_PIN 42 + #endif + #ifndef Z_SERIAL_RX_PIN + #define Z_SERIAL_RX_PIN 65 + #endif + #ifndef Z2_SERIAL_TX_PIN + #define Z2_SERIAL_TX_PIN -1 + #endif + #ifndef Z2_SERIAL_RX_PIN + #define Z2_SERIAL_RX_PIN -1 + #endif - #define E0_SERIAL_TX_PIN 44 - #define E0_SERIAL_RX_PIN 66 - #define E1_SERIAL_TX_PIN -1 - #define E1_SERIAL_RX_PIN -1 - #define E2_SERIAL_TX_PIN -1 - #define E2_SERIAL_RX_PIN -1 - #define E3_SERIAL_TX_PIN -1 - #define E3_SERIAL_RX_PIN -1 - #define E4_SERIAL_TX_PIN -1 - #define E4_SERIAL_RX_PIN -1 + #ifndef E0_SERIAL_TX_PIN + #define E0_SERIAL_TX_PIN 44 + #endif + #ifndef E0_SERIAL_RX_PIN + #define E0_SERIAL_RX_PIN 66 + #endif + #ifndef E1_SERIAL_TX_PIN + #define E1_SERIAL_TX_PIN -1 + #endif + #ifndef E1_SERIAL_RX_PIN + #define E1_SERIAL_RX_PIN -1 + #endif + #ifndef E2_SERIAL_TX_PIN + #define E2_SERIAL_TX_PIN -1 + #endif + #ifndef E2_SERIAL_RX_PIN + #define E2_SERIAL_RX_PIN -1 + #endif + #ifndef E3_SERIAL_TX_PIN + #define E3_SERIAL_TX_PIN -1 + #endif + #ifndef E3_SERIAL_RX_PIN + #define E3_SERIAL_RX_PIN -1 + #endif + #ifndef E4_SERIAL_TX_PIN + #define E4_SERIAL_TX_PIN -1 + #endif + #ifndef E4_SERIAL_RX_PIN + #define E4_SERIAL_RX_PIN -1 + #endif #endif diff --git a/Marlin/src/pins/pins_ADSK.h b/Marlin/src/pins/sam/pins_ADSK.h similarity index 100% rename from Marlin/src/pins/pins_ADSK.h rename to Marlin/src/pins/sam/pins_ADSK.h diff --git a/Marlin/src/pins/pins_ALLIGATOR_R2.h b/Marlin/src/pins/sam/pins_ALLIGATOR_R2.h similarity index 100% rename from Marlin/src/pins/pins_ALLIGATOR_R2.h rename to Marlin/src/pins/sam/pins_ALLIGATOR_R2.h diff --git a/Marlin/src/pins/pins_ARCHIM1.h b/Marlin/src/pins/sam/pins_ARCHIM1.h similarity index 100% rename from Marlin/src/pins/pins_ARCHIM1.h rename to Marlin/src/pins/sam/pins_ARCHIM1.h diff --git a/Marlin/src/pins/pins_ARCHIM2.h b/Marlin/src/pins/sam/pins_ARCHIM2.h similarity index 97% rename from Marlin/src/pins/pins_ARCHIM2.h rename to Marlin/src/pins/sam/pins_ARCHIM2.h index 69ea78715d..95200adb34 100644 --- a/Marlin/src/pins/pins_ARCHIM2.h +++ b/Marlin/src/pins/sam/pins_ARCHIM2.h @@ -149,9 +149,15 @@ // Required for the Archim2 board. // #if ENABLED(TMC_USE_SW_SPI) - #define TMC_SW_MOSI 28 // PD3 - #define TMC_SW_MISO 26 // PD1 - #define TMC_SW_SCK 27 // PD2 + #ifndef TMC_SW_MOSI + #define TMC_SW_MOSI 28 // PD3 + #endif + #ifndef TMC_SW_MISO + #define TMC_SW_MISO 26 // PD1 + #endif + #ifndef TMC_SW_SCK + #define TMC_SW_SCK 27 // PD2 + #endif #endif // diff --git a/Marlin/src/pins/pins_DUE3DOM.h b/Marlin/src/pins/sam/pins_DUE3DOM.h similarity index 100% rename from Marlin/src/pins/pins_DUE3DOM.h rename to Marlin/src/pins/sam/pins_DUE3DOM.h diff --git a/Marlin/src/pins/pins_DUE3DOM_MINI.h b/Marlin/src/pins/sam/pins_DUE3DOM_MINI.h similarity index 100% rename from Marlin/src/pins/pins_DUE3DOM_MINI.h rename to Marlin/src/pins/sam/pins_DUE3DOM_MINI.h diff --git a/Marlin/src/pins/pins_PRINTRBOARD_G2.h b/Marlin/src/pins/sam/pins_PRINTRBOARD_G2.h similarity index 100% rename from Marlin/src/pins/pins_PRINTRBOARD_G2.h rename to Marlin/src/pins/sam/pins_PRINTRBOARD_G2.h diff --git a/Marlin/src/pins/pins_RADDS.h b/Marlin/src/pins/sam/pins_RADDS.h similarity index 99% rename from Marlin/src/pins/pins_RADDS.h rename to Marlin/src/pins/sam/pins_RADDS.h index 66b06c2c43..52c6388268 100644 --- a/Marlin/src/pins/pins_RADDS.h +++ b/Marlin/src/pins/sam/pins_RADDS.h @@ -201,9 +201,8 @@ #define FIL_RUNOUT_PIN 39 // SERVO2_PIN #endif -// I2C EEPROM with 8K of space #define I2C_EEPROM -#define E2END 0x1FFF +#define E2END 0x1FFF // 8KB // // LCD / Controller diff --git a/Marlin/src/pins/pins_RAMPS4DUE.h b/Marlin/src/pins/sam/pins_RAMPS4DUE.h similarity index 95% rename from Marlin/src/pins/pins_RAMPS4DUE.h rename to Marlin/src/pins/sam/pins_RAMPS4DUE.h index a4ed62bb07..c36ed150e4 100644 --- a/Marlin/src/pins/pins_RAMPS4DUE.h +++ b/Marlin/src/pins/sam/pins_RAMPS4DUE.h @@ -44,18 +44,13 @@ #endif #define BOARD_NAME "RAMPS4DUE" - #define IS_RAMPS4DUE -#include "pins_RAMPS.h" // // Temperature Sensors // -#undef TEMP_0_PIN #define TEMP_0_PIN 9 // Analog Input - -#undef TEMP_1_PIN #define TEMP_1_PIN -1 // Analog Input - -#undef TEMP_BED_PIN #define TEMP_BED_PIN 10 // Analog Input + +#include "../ramps/pins_RAMPS.h" diff --git a/Marlin/src/pins/pins_RAMPS_DUO.h b/Marlin/src/pins/sam/pins_RAMPS_DUO.h similarity index 91% rename from Marlin/src/pins/pins_RAMPS_DUO.h rename to Marlin/src/pins/sam/pins_RAMPS_DUO.h index 95a4daa5bc..bfee7c753a 100644 --- a/Marlin/src/pins/pins_RAMPS_DUO.h +++ b/Marlin/src/pins/sam/pins_RAMPS_DUO.h @@ -67,9 +67,9 @@ // SPI for Max6675 or Max31855 Thermocouple #undef MAX6675_SS_PIN #if DISABLED(SDSUPPORT) - #define MAX6675_SS_PIN 69 // Do not use pin 53 if there is even the remote possibility of using Display/SD card + #define MAX6675_SS_PIN 69 // Don't use 53 if there is even the remote possibility of using Display/SD card #else - #define MAX6675_SS_PIN 69 // Do not use pin 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present + #define MAX6675_SS_PIN 69 // Don't use 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present #endif // diff --git a/Marlin/src/pins/pins_RAMPS_FD_V1.h b/Marlin/src/pins/sam/pins_RAMPS_FD_V1.h similarity index 98% rename from Marlin/src/pins/pins_RAMPS_FD_V1.h rename to Marlin/src/pins/sam/pins_RAMPS_FD_V1.h index 684489403a..c0e3584c3c 100644 --- a/Marlin/src/pins/pins_RAMPS_FD_V1.h +++ b/Marlin/src/pins/sam/pins_RAMPS_FD_V1.h @@ -205,7 +205,7 @@ #endif // HAS_SPI_LCD -#if HAS_DRIVER(TMC2208) || HAS_DRIVER(TMC2209) +#if HAS_TMC220x /** * TMC2208/TMC2209 stepper drivers * @@ -230,6 +230,6 @@ // #if HOTENDS < 3 && HAS_CUTTER && !PIN_EXISTS(SPINDLE_LASER_ENA) #define SPINDLE_LASER_ENA_PIN 45 // Use E2 ENA - #define SPINDLE_LASER_PWM_PIN 12 // MUST BE HARDWARE PWM + #define SPINDLE_LASER_PWM_PIN 12 // Hardware PWM #define SPINDLE_DIR_PIN 47 // Use E2 DIR #endif diff --git a/Marlin/src/pins/pins_RAMPS_FD_V2.h b/Marlin/src/pins/sam/pins_RAMPS_FD_V2.h similarity index 100% rename from Marlin/src/pins/pins_RAMPS_FD_V2.h rename to Marlin/src/pins/sam/pins_RAMPS_FD_V2.h diff --git a/Marlin/src/pins/pins_RAMPS_SMART.h b/Marlin/src/pins/sam/pins_RAMPS_SMART.h similarity index 92% rename from Marlin/src/pins/pins_RAMPS_SMART.h rename to Marlin/src/pins/sam/pins_RAMPS_SMART.h index cd65aef627..0ba4114804 100644 --- a/Marlin/src/pins/pins_RAMPS_SMART.h +++ b/Marlin/src/pins/sam/pins_RAMPS_SMART.h @@ -90,9 +90,9 @@ // SPI for Max6675 or Max31855 Thermocouple #undef MAX6675_SS_PIN #if DISABLED(SDSUPPORT) - #define MAX6675_SS_PIN 67 // Do not use pin 53 if there is even the remote possibility of using Display/SD card + #define MAX6675_SS_PIN 67 // Don't use 53 if there is even the remote possibility of using Display/SD card #else - #define MAX6675_SS_PIN 67 // Do not use pin 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present + #define MAX6675_SS_PIN 67 // Don't use 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present #endif // diff --git a/Marlin/src/pins/pins_RURAMPS4D_11.h b/Marlin/src/pins/sam/pins_RURAMPS4D_11.h similarity index 100% rename from Marlin/src/pins/pins_RURAMPS4D_11.h rename to Marlin/src/pins/sam/pins_RURAMPS4D_11.h diff --git a/Marlin/src/pins/pins_RURAMPS4D_13.h b/Marlin/src/pins/sam/pins_RURAMPS4D_13.h similarity index 100% rename from Marlin/src/pins/pins_RURAMPS4D_13.h rename to Marlin/src/pins/sam/pins_RURAMPS4D_13.h diff --git a/Marlin/src/pins/pins_ULTRATRONICS_PRO.h b/Marlin/src/pins/sam/pins_ULTRATRONICS_PRO.h similarity index 100% rename from Marlin/src/pins/pins_ULTRATRONICS_PRO.h rename to Marlin/src/pins/sam/pins_ULTRATRONICS_PRO.h diff --git a/Marlin/src/pins/samd/pins_AGCM4_RURAMPS4D_13.h b/Marlin/src/pins/samd/pins_AGCM4_RURAMPS4D_13.h new file mode 100644 index 0000000000..ee5f16a1e6 --- /dev/null +++ b/Marlin/src/pins/samd/pins_AGCM4_RURAMPS4D_13.h @@ -0,0 +1,254 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + */ + +/** + * Adafruit Grand Central M4 pin assignments ported by Giuliano Zaro + */ +#ifndef ARDUINO_GRAND_CENTRAL_M4 + #error "Oops! Select 'Adafruit Grand Central M4' in 'Tools > Board.'" +#endif + +#define BOARD_NAME "RuRAMPS4AGCM4 v1.3" + +// +// Servos +// +#define SERVO0_PIN 5 +#define SERVO1_PIN 3 + +// +// Limit Switches +// +#define X_MIN_PIN 45 +#define X_MAX_PIN 39 +#define Y_MIN_PIN 46 +#define Y_MAX_PIN 41 +#define Z_MIN_PIN 47 +#define Z_MAX_PIN 43 + +// +// Z Probe (when not Z_MIN_PIN) +// +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN 49 +#endif + +// +// Steppers +// +#define X_STEP_PIN 37 // Support Extension Board +#define X_DIR_PIN 36 +#define X_ENABLE_PIN 31 +#ifndef X_CS_PIN + #define X_CS_PIN 38 +#endif + +#define Y_STEP_PIN 32 // Support Extension Board +#define Y_DIR_PIN 35 +#define Y_ENABLE_PIN 31 +#ifndef Y_CS_PIN + #define Y_CS_PIN 34 +#endif + +#define Z_STEP_PIN 30 // Support Extension Board +#define Z_DIR_PIN 2 +#define Z_ENABLE_PIN 31 +#ifndef Z_CS_PIN + #define Z_CS_PIN 10 +#endif + +#define E0_STEP_PIN 29 +#define E0_DIR_PIN 28 +#define E0_ENABLE_PIN 33 +#ifndef E0_CS_PIN + #define E0_CS_PIN 14 +#endif + +#define E1_STEP_PIN 22 +#define E1_DIR_PIN 24 +#define E1_ENABLE_PIN 26 +#ifndef E1_CS_PIN + #define E1_CS_PIN 15 +#endif + +#define E2_STEP_PIN 25 +#define E2_DIR_PIN 23 +#define E2_ENABLE_PIN 27 +#ifndef E2_CS_PIN + #define E2_CS_PIN 74 +#endif + +#if USES_Z_MIN_PROBE_ENDSTOP + #define Z_MIN_PROBE_PIN 49 +#endif + +#if HAS_FILAMENT_SENSOR + #ifndef FIL_RUNOUT_PIN + #define FIL_RUNOUT_PIN Y_MIN_PIN + #endif +#endif + +// +// Heaters / Fans +// +#define HEATER_0_PIN 13 +#define HEATER_1_PIN 12 +#define HEATER_2_PIN 11 +#define HEATER_BED_PIN 7 // BED H1 + +#define FAN_PIN 9 +#define FAN1_PIN 8 +#define CONTROLLER_FAN_PIN -1 + +// +// Temperature Sensors +// +#define TEMP_0_PIN 0 // ANALOG A0 +#define TEMP_1_PIN 1 // ANALOG A1 +#define TEMP_2_PIN 2 // ANALOG A2 +#define TEMP_3_PIN 3 // ANALOG A3 +#define TEMP_BED_PIN 4 // ANALOG A4 + +// The thermocouple uses Analog pins +#if ENABLED(VER_WITH_THERMOCOUPLE) // Must be defined in Configuration.h + #define TEMP_4_PIN 5 // A5 + #define TEMP_5_PIN 6 // A6 (Marlin 2.0 not support) +#endif + +// SPI for Max6675 or Max31855 Thermocouple +/* +#if DISABLED(SDSUPPORT) + #define MAX6675_SS_PIN 53 +#else + #define MAX6675_SS_PIN 49 +#endif +*/ + +// +// Misc. Functions +// +#define SDSS 4 +#define LED_PIN -1 // 13 - HEATER_0_PIN +#define PS_ON_PIN -1 // 57 + +// MKS TFT / Nextion Use internal USART-1 +#define TFT_LCD_MODULE_COM 1 +#define TFT_LCD_MODULE_BAUDRATE 115200 + +// ESP WiFi Use internal USART-2 +#define ESP_WIFI_MODULE_COM 2 +#define ESP_WIFI_MODULE_BAUDRATE 115200 +#define ESP_WIFI_MODULE_RESET_PIN -1 +#define PIGGY_GPIO_PIN -1 + +// +// EEPROM +// +#define E2END 0x7FFF // 32Kb (24lc256) +#define I2C_EEPROM // EEPROM on I2C + +// +// LCD / Controller +// +#if HAS_SPI_LCD + + #if EITHER(RADDS_DISPLAY, REPRAP_DISCOUNT_SMART_CONTROLLER) + + #define BEEPER_PIN 75 + #define LCD_PINS_D4 48 + #define LCD_PINS_D7 53 + #define SD_DETECT_PIN -1 // 51 can't be used, it's MOSI + #define LCD_PINS_RS 76 + #define LCD_PINS_ENABLE 77 + + #elif ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) + + #define BEEPER_PIN 75 + #define LCD_PINS_D4 48 + #define SD_DETECT_PIN -1 // 51 can't be used, it's MOSI + #define LCD_PINS_RS 76 + #define LCD_PINS_ENABLE 77 + + #elif HAS_SSD1306_OLED_I2C + + #define BEEPER_PIN 75 + #define LCD_SDSS 10 + #define SD_DETECT_PIN -1 // 51 can't be used, it's MOSI + + #elif ENABLED(FYSETC_MINI_12864) + + #define BEEPER_PIN 75 + #define DOGLCD_CS 77 + #define DOGLCD_A0 76 + + //#define FORCE_SOFT_SPI // Use this if default of hardware SPI causes display problems + // results in LCD soft SPI mode 3, SD soft SPI mode 0 + + #define LCD_RESET_PIN 48 // Must be high or open for LCD to operate normally. + + #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0) + #error "Pin compatibility check needed! Grand central M4 pins 50, 51 and 52 are not GPIO pins, they are wired to MISO, MOSI, and SCK." + #ifndef RGB_LED_R_PIN + #define RGB_LED_R_PIN 50 // D5 + #endif + #ifndef RGB_LED_G_PIN + #define RGB_LED_G_PIN 52 // D6 + #endif + #ifndef RGB_LED_B_PIN + #define RGB_LED_B_PIN 53 // D7 + #endif + #elif ENABLED(FYSETC_MINI_12864_2_1) + #error "Pin compatibility check needed! Grand central M4 pins 50, 51 and 52 are not GPIO pins, they are wired to MISO, MOSI, and SCK." + #define NEOPIXEL_PIN 50 // D5 + #endif + + #elif ENABLED(MKS_MINI_12864) + #error "Pin compatibility check needed! Grand central M4 pins 50, 51 and 52 are not GPIO pins, they are wired to MISO, MOSI, and SCK." + #define ORIG_BEEPER_PIN 75 + + #define DOGLCD_A0 52 + #define DOGLCD_CS 50 + + #define SD_DETECT_PIN -1 // 51 can't be used, it's MOSI + + #endif + + #if ENABLED(NEWPANEL) + #define BTN_EN1 44 + #define BTN_EN2 42 + #define BTN_ENC 40 + #endif + +#endif // HAS_SPI_LCD + +// +// SD Support +// +#ifndef SDCARD_CONNECTION + #define SDCARD_CONNECTION ONBOARD +#endif + +#if SD_CONNECTION_IS(ONBOARD) + #undef SDSS + #define SDSS 83 + #undef SD_DETECT_PIN + #define SD_DETECT_PIN 95 +#endif diff --git a/Marlin/src/pins/pins_ANET_10.h b/Marlin/src/pins/sanguino/pins_ANET_10.h similarity index 100% rename from Marlin/src/pins/pins_ANET_10.h rename to Marlin/src/pins/sanguino/pins_ANET_10.h diff --git a/Marlin/src/pins/pins_AZTEEG_X1.h b/Marlin/src/pins/sanguino/pins_AZTEEG_X1.h similarity index 100% rename from Marlin/src/pins/pins_AZTEEG_X1.h rename to Marlin/src/pins/sanguino/pins_AZTEEG_X1.h diff --git a/Marlin/src/pins/pins_GEN3_MONOLITHIC.h b/Marlin/src/pins/sanguino/pins_GEN3_MONOLITHIC.h similarity index 100% rename from Marlin/src/pins/pins_GEN3_MONOLITHIC.h rename to Marlin/src/pins/sanguino/pins_GEN3_MONOLITHIC.h diff --git a/Marlin/src/pins/pins_GEN3_PLUS.h b/Marlin/src/pins/sanguino/pins_GEN3_PLUS.h similarity index 100% rename from Marlin/src/pins/pins_GEN3_PLUS.h rename to Marlin/src/pins/sanguino/pins_GEN3_PLUS.h diff --git a/Marlin/src/pins/pins_GEN6.h b/Marlin/src/pins/sanguino/pins_GEN6.h similarity index 94% rename from Marlin/src/pins/pins_GEN6.h rename to Marlin/src/pins/sanguino/pins_GEN6.h index 42abd00137..2857f6f777 100644 --- a/Marlin/src/pins/pins_GEN6.h +++ b/Marlin/src/pins/sanguino/pins_GEN6.h @@ -106,7 +106,7 @@ // #define SDSS 17 #define DEBUG_PIN 0 -#define CASE_LIGHT_PIN 16 // MUST BE HARDWARE PWM +#define CASE_LIGHT_PIN 16 // Hardware PWM // RS485 pins #define TX_ENABLE_PIN 12 @@ -115,6 +115,6 @@ // // M3/M4/M5 - Spindle/Laser Control // -#define SPINDLE_LASER_ENA_PIN 5 // Pin should have a pullup/pulldown! -#define SPINDLE_LASER_PWM_PIN 16 // MUST BE HARDWARE PWM +#define SPINDLE_LASER_ENA_PIN 5 // Pullup or pulldown! +#define SPINDLE_LASER_PWM_PIN 16 // Hardware PWM #define SPINDLE_DIR_PIN 6 diff --git a/Marlin/src/pins/pins_GEN6_DELUXE.h b/Marlin/src/pins/sanguino/pins_GEN6_DELUXE.h similarity index 100% rename from Marlin/src/pins/pins_GEN6_DELUXE.h rename to Marlin/src/pins/sanguino/pins_GEN6_DELUXE.h diff --git a/Marlin/src/pins/pins_GEN7_12.h b/Marlin/src/pins/sanguino/pins_GEN7_12.h similarity index 91% rename from Marlin/src/pins/pins_GEN7_12.h rename to Marlin/src/pins/sanguino/pins_GEN7_12.h index 2b9411feb3..cd1b5b5998 100644 --- a/Marlin/src/pins/pins_GEN7_12.h +++ b/Marlin/src/pins/sanguino/pins_GEN7_12.h @@ -123,14 +123,14 @@ #define PS_ON_PIN 15 #if GEN7_VERSION < 13 - #define CASE_LIGHT_PIN 16 // MUST BE HARDWARE PWM + #define CASE_LIGHT_PIN 16 // Hardware PWM #else // Gen7 v1.3 removed the I2C connector & signals so need to get PWM off the PC power supply header - #define CASE_LIGHT_PIN 15 // MUST BE HARDWARE PWM + #define CASE_LIGHT_PIN 15 // Hardware PWM #endif // All these generations of Gen7 supply thermistor power // via PS_ON, so ignore bad thermistor readings -#define BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE +//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000 #define DEBUG_PIN 0 @@ -141,10 +141,10 @@ // // M3/M4/M5 - Spindle/Laser Control // -#define SPINDLE_LASER_ENA_PIN 10 // Pin should have a pullup/pulldown! +#define SPINDLE_LASER_ENA_PIN 10 // Pullup or pulldown! #define SPINDLE_DIR_PIN 11 #if GEN7_VERSION < 13 - #define SPINDLE_LASER_PWM_PIN 16 // MUST BE HARDWARE PWM + #define SPINDLE_LASER_PWM_PIN 16 // Hardware PWM #else // Gen7 v1.3 removed the I2C connector & signals so need to get PWM off the PC power supply header - #define SPINDLE_LASER_PWM_PIN 15 // MUST BE HARDWARE PWM + #define SPINDLE_LASER_PWM_PIN 15 // Hardware PWM #endif diff --git a/Marlin/src/pins/pins_GEN7_13.h b/Marlin/src/pins/sanguino/pins_GEN7_13.h similarity index 100% rename from Marlin/src/pins/pins_GEN7_13.h rename to Marlin/src/pins/sanguino/pins_GEN7_13.h diff --git a/Marlin/src/pins/pins_GEN7_14.h b/Marlin/src/pins/sanguino/pins_GEN7_14.h similarity index 93% rename from Marlin/src/pins/pins_GEN7_14.h rename to Marlin/src/pins/sanguino/pins_GEN7_14.h index 6228db7ac4..064ffd81e2 100644 --- a/Marlin/src/pins/pins_GEN7_14.h +++ b/Marlin/src/pins/sanguino/pins_GEN7_14.h @@ -102,7 +102,7 @@ // Misc. Functions // #define PS_ON_PIN 15 -#define CASE_LIGHT_PIN 15 // MUST BE HARDWARE PWM +#define CASE_LIGHT_PIN 15 // Hardware PWM // A pin for debugging #define DEBUG_PIN 0 @@ -114,6 +114,6 @@ // // M3/M4/M5 - Spindle/Laser Control // -#define SPINDLE_LASER_ENA_PIN 20 // Pin should have a pullup/pulldown! -#define SPINDLE_LASER_PWM_PIN 16 // MUST BE HARDWARE PWM +#define SPINDLE_LASER_ENA_PIN 20 // Pullup or pulldown! +#define SPINDLE_LASER_PWM_PIN 16 // Hardware PWM #define SPINDLE_DIR_PIN 21 diff --git a/Marlin/src/pins/pins_GEN7_CUSTOM.h b/Marlin/src/pins/sanguino/pins_GEN7_CUSTOM.h similarity index 94% rename from Marlin/src/pins/pins_GEN7_CUSTOM.h rename to Marlin/src/pins/sanguino/pins_GEN7_CUSTOM.h index 04689b2ca8..d3e2b35a6d 100644 --- a/Marlin/src/pins/pins_GEN7_CUSTOM.h +++ b/Marlin/src/pins/sanguino/pins_GEN7_CUSTOM.h @@ -104,7 +104,7 @@ // #define SDSS 31 // SCL pin of I2C header || CS Pin for SD Card support #define PS_ON_PIN 19 -#define CASE_LIGHT_PIN 15 // MUST BE HARDWARE PWM +#define CASE_LIGHT_PIN 15 // Hardware PWM // A pin for debugging #define DEBUG_PIN -1 @@ -134,6 +134,6 @@ // // M3/M4/M5 - Spindle/Laser Control // -#define SPINDLE_LASER_ENA_PIN 5 // Pin should have a pullup/pulldown! -#define SPINDLE_LASER_PWM_PIN 16 // MUST BE HARDWARE PWM +#define SPINDLE_LASER_ENA_PIN 5 // Pullup or pulldown! +#define SPINDLE_LASER_PWM_PIN 16 // Hardware PWM #define SPINDLE_DIR_PIN 6 diff --git a/Marlin/src/pins/pins_MELZI.h b/Marlin/src/pins/sanguino/pins_MELZI.h similarity index 100% rename from Marlin/src/pins/pins_MELZI.h rename to Marlin/src/pins/sanguino/pins_MELZI.h diff --git a/Marlin/src/pins/pins_MELZI_CREALITY.h b/Marlin/src/pins/sanguino/pins_MELZI_CREALITY.h similarity index 100% rename from Marlin/src/pins/pins_MELZI_CREALITY.h rename to Marlin/src/pins/sanguino/pins_MELZI_CREALITY.h diff --git a/Marlin/src/pins/pins_MELZI_MAKR3D.h b/Marlin/src/pins/sanguino/pins_MELZI_MAKR3D.h similarity index 100% rename from Marlin/src/pins/pins_MELZI_MAKR3D.h rename to Marlin/src/pins/sanguino/pins_MELZI_MAKR3D.h diff --git a/Marlin/src/pins/pins_MELZI_MALYAN.h b/Marlin/src/pins/sanguino/pins_MELZI_MALYAN.h similarity index 100% rename from Marlin/src/pins/pins_MELZI_MALYAN.h rename to Marlin/src/pins/sanguino/pins_MELZI_MALYAN.h diff --git a/Marlin/src/pins/pins_MELZI_TRONXY.h b/Marlin/src/pins/sanguino/pins_MELZI_TRONXY.h similarity index 100% rename from Marlin/src/pins/pins_MELZI_TRONXY.h rename to Marlin/src/pins/sanguino/pins_MELZI_TRONXY.h diff --git a/Marlin/src/pins/pins_OMCA.h b/Marlin/src/pins/sanguino/pins_OMCA.h similarity index 100% rename from Marlin/src/pins/pins_OMCA.h rename to Marlin/src/pins/sanguino/pins_OMCA.h diff --git a/Marlin/src/pins/pins_OMCA_A.h b/Marlin/src/pins/sanguino/pins_OMCA_A.h similarity index 100% rename from Marlin/src/pins/pins_OMCA_A.h rename to Marlin/src/pins/sanguino/pins_OMCA_A.h diff --git a/Marlin/src/pins/pins_SANGUINOLOLU_11.h b/Marlin/src/pins/sanguino/pins_SANGUINOLOLU_11.h similarity index 95% rename from Marlin/src/pins/pins_SANGUINOLOLU_11.h rename to Marlin/src/pins/sanguino/pins_SANGUINOLOLU_11.h index f94d7a03e9..978a21d2e7 100644 --- a/Marlin/src/pins/pins_SANGUINOLOLU_11.h +++ b/Marlin/src/pins/sanguino/pins_SANGUINOLOLU_11.h @@ -139,7 +139,7 @@ #endif #if NONE(SPINDLE_FEATURE, LASER_FEATURE) && ENABLED(SANGUINOLOLU_V_1_2) && !BOTH(ULTRA_LCD, NEWPANEL) // try to use IO Header - #define CASE_LIGHT_PIN 4 // MUST BE HARDWARE PWM - see if IO Header is available + #define CASE_LIGHT_PIN 4 // Hardware PWM - see if IO Header is available #endif /** @@ -280,8 +280,8 @@ #if HAS_CUTTER #if !MB(AZTEEG_X1) && ENABLED(SANGUINOLOLU_V_1_2) && !BOTH(ULTRA_LCD, NEWPANEL) // try to use IO Header - #define SPINDLE_LASER_ENA_PIN 10 // Pin should have a pullup/pulldown! - #define SPINDLE_LASER_PWM_PIN 4 // MUST BE HARDWARE PWM + #define SPINDLE_LASER_ENA_PIN 10 // Pullup or pulldown! + #define SPINDLE_LASER_PWM_PIN 4 // Hardware PWM #define SPINDLE_DIR_PIN 11 #elif !MB(MELZI) // use X stepper motor socket @@ -319,8 +319,8 @@ #define X_DIR_PIN 0 #define X_ENABLE_PIN 14 #define X_STEP_PIN 1 - #define SPINDLE_LASER_PWM_PIN 15 // MUST BE HARDWARE PWM - #define SPINDLE_LASER_ENA_PIN 21 // Pin should have a pullup! + #define SPINDLE_LASER_PWM_PIN 15 // Hardware PWM + #define SPINDLE_LASER_ENA_PIN 21 // Pullup! #define SPINDLE_DIR_PIN -1 // No pin available on the socket for the direction pin #endif #endif diff --git a/Marlin/src/pins/pins_SANGUINOLOLU_12.h b/Marlin/src/pins/sanguino/pins_SANGUINOLOLU_12.h similarity index 100% rename from Marlin/src/pins/pins_SANGUINOLOLU_12.h rename to Marlin/src/pins/sanguino/pins_SANGUINOLOLU_12.h diff --git a/Marlin/src/pins/pins_SETHI.h b/Marlin/src/pins/sanguino/pins_SETHI.h similarity index 98% rename from Marlin/src/pins/pins_SETHI.h rename to Marlin/src/pins/sanguino/pins_SETHI.h index 049526a8f1..23b985fbac 100644 --- a/Marlin/src/pins/pins_SETHI.h +++ b/Marlin/src/pins/sanguino/pins_SETHI.h @@ -115,7 +115,7 @@ // All these generations of Gen7 supply thermistor power // via PS_ON, so ignore bad thermistor readings -#define BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE +//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000 // our pin for debugging. #define DEBUG_PIN 0 diff --git a/Marlin/src/pins/pins_STB_11.h b/Marlin/src/pins/sanguino/pins_STB_11.h similarity index 99% rename from Marlin/src/pins/pins_STB_11.h rename to Marlin/src/pins/sanguino/pins_STB_11.h index 9f14f1b421..511b938c4b 100644 --- a/Marlin/src/pins/pins_STB_11.h +++ b/Marlin/src/pins/sanguino/pins_STB_11.h @@ -26,4 +26,5 @@ */ #define BOARD_NAME "STB V1.1" + #include "pins_SANGUINOLOLU_12.h" diff --git a/Marlin/src/pins/sensitive_pins.h b/Marlin/src/pins/sensitive_pins.h index 6fba6639fd..fc3a486c37 100644 --- a/Marlin/src/pins/sensitive_pins.h +++ b/Marlin/src/pins/sensitive_pins.h @@ -131,7 +131,7 @@ // Mixing stepper, Switching stepper, or regular stepper #define E_NEEDED(N) (ENABLED(MIXING_EXTRUDER) && MIXING_STEPPERS > N) \ || (ENABLED(SWITCHING_EXTRUDER) && E_STEPPERS > N) \ - || (DISABLED(SWITCHING_EXTRUDER, MIXING_EXTRUDER) && EXTRUDERS > N) + || (NONE(SWITCHING_EXTRUDER, MIXING_EXTRUDER) && EXTRUDERS > N) #define _E0_CS #define _E0_MS1 diff --git a/Marlin/src/pins/pins_ARMED.h b/Marlin/src/pins/stm32/pins_ARMED.h similarity index 61% rename from Marlin/src/pins/pins_ARMED.h rename to Marlin/src/pins/stm32/pins_ARMED.h index 396495ea8f..ea1c11f39b 100644 --- a/Marlin/src/pins/pins_ARMED.h +++ b/Marlin/src/pins/stm32/pins_ARMED.h @@ -23,42 +23,43 @@ #ifndef STM32F4 #error "Oops! Select an STM32F4 board in 'Tools > Board.'" +#elif HOTENDS > 2 || E_STEPPERS > 2 + #error "Arm'ed supports up to 2 hotends / E-steppers." #endif #ifndef ARMED_V1_0 #define ARMED_V1_1 #endif -#define DEFAULT_MACHINE_NAME "Arm'ed" - -#undef BOARD_NAME -#define BOARD_NAME "Arm'ed" +#undef BOARD_NAME // Defined on the command line by Arduino Core STM32 +#define BOARD_NAME "Arm'ed" +#define DEFAULT_MACHINE_NAME BOARD_NAME #define I2C_EEPROM -#undef E2END -#define E2END 0xFFF // EEPROM end address (4kB) - -#if HOTENDS > 2 || E_STEPPERS > 2 - #error "Arm'ed supports up to 2 hotends / E-steppers." -#endif +#undef E2END // Defined in Arduino Core STM32 to be used with EEPROM emulation. This board uses a real EEPROM. +#define E2END 0xFFF // 4KB // // Limit Switches // -#define X_MIN_PIN PE0 -#define X_MAX_PIN -1 -#define Y_MIN_PIN PE1 -#define Y_MAX_PIN -1 -#define Z_MIN_PIN PE14 -#define Z_MAX_PIN -1 +#define X_STOP_PIN PE0 +#define Y_STOP_PIN PE1 +#define Z_STOP_PIN PE14 // // Z Probe (when not Z_MIN_PIN) // -// #ifndef Z_MIN_PROBE_PIN -// #define Z_MIN_PROBE_PIN PA4 -// #endif +//#ifndef Z_MIN_PROBE_PIN +// #define Z_MIN_PROBE_PIN PA4 +//#endif + +// +// Filament Runout Sensor +// +#ifndef FIL_RUNOUT_PIN + #define FIL_RUNOUT_PIN PA3 +#endif // // Steppers @@ -88,13 +89,12 @@ #define E0_STEP_PIN PB5 #define E0_DIR_PIN PB6 -#define E0_CS_PIN PB4 - -#ifdef ARMED_V1_0 - #define E0_ENABLE_PIN PB3 -#else +#ifdef ARMED_V1_1 #define E0_ENABLE_PIN PC12 +#else + #define E0_ENABLE_PIN PB3 #endif +#define E0_CS_PIN PB4 #ifdef ARMED_SWAP_X_E1 #define E1_STEP_PIN PD3 @@ -118,13 +118,13 @@ // // Heaters / Fans // -#define HEATER_0_PIN PA1 // PWM pin -#define HEATER_1_PIN PA2 // PWM pin -#define HEATER_BED_PIN PA0 // PWM pin +#define HEATER_0_PIN PA1 // Hardware PWM +#define HEATER_1_PIN PA2 // Hardware PWM +#define HEATER_BED_PIN PA0 // Hardware PWM -#define FAN_PIN PC6 // PWM pin, Part cooling fan -#define FAN1_PIN PC7 // PWM pin, Extruder fan -#define FAN2_PIN PC8 // PWM pin, Controller fan +#define FAN_PIN PC6 // Hardware PWM, Part cooling fan +#define FAN1_PIN PC7 // Hardware PWM, Extruder fan +#define FAN2_PIN PC8 // Hardware PWM, Controller fan // // Misc functions @@ -140,21 +140,49 @@ // #define SD_DETECT_PIN PA15 #define BEEPER_PIN PC9 -#define LCD_PINS_RS PE9 -#define LCD_PINS_ENABLE PE8 -#define LCD_PINS_D4 PB12 -#define LCD_PINS_D5 PB13 -#define LCD_PINS_D6 PB14 -#define LCD_PINS_D7 PB15 + +#if ENABLED(FYSETC_MINI_12864) + // + // See https://wiki.fysetc.com/Mini12864_Panel/?fbclid=IwAR1FyjuNdVOOy9_xzky3qqo_WeM5h-4gpRnnWhQr_O1Ef3h0AFnFXmCehK8 + // + #define DOGLCD_A0 PE9 + #define DOGLCD_CS PE8 + + #define LCD_BACKLIGHT_PIN -1 + + #define LCD_RESET_PIN PB12 // Must be high or open for LCD to operate normally. + + #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0) + #ifndef RGB_LED_R_PIN + #define RGB_LED_R_PIN PB13 + #endif + #ifndef RGB_LED_G_PIN + #define RGB_LED_G_PIN PB14 + #endif + #ifndef RGB_LED_B_PIN + #define RGB_LED_B_PIN PB15 + #endif + #elif ENABLED(FYSETC_MINI_12864_2_1) + #define NEOPIXEL_PIN PB13 + #endif +#else + #define LCD_PINS_RS PE9 + #define LCD_PINS_ENABLE PE8 + #define LCD_PINS_D4 PB12 + #define LCD_PINS_D5 PB13 + #define LCD_PINS_D6 PB14 + #define LCD_PINS_D7 PB15 + + #if ENABLED(MKS_MINI_12864) + #define DOGLCD_CS PB13 + #define DOGLCD_A0 PB14 + #endif +#endif + #define BTN_EN1 PC4 #define BTN_EN2 PC5 #define BTN_ENC PC3 -// -// Filament runout detection -// -#define FIL_RUNOUT_PIN PA3 - // // Extension pins // diff --git a/Marlin/src/pins/pins_BEAST.h b/Marlin/src/pins/stm32/pins_BEAST.h similarity index 96% rename from Marlin/src/pins/pins_BEAST.h rename to Marlin/src/pins/stm32/pins_BEAST.h index 57efda845a..44204f0c9c 100644 --- a/Marlin/src/pins/pins_BEAST.h +++ b/Marlin/src/pins/stm32/pins_BEAST.h @@ -29,14 +29,14 @@ * 21017 Victor Perez Marlin for stm32f1 test */ +#define BOARD_NAME "Beast STM32" #define DEFAULT_MACHINE_NAME "STM32F103RET6" -#define BOARD_NAME "Marlin for STM32" // Enable I2C_EEPROM for testing #define I2C_EEPROM -// Ignore temp readings during develpment. -#define BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE +// Ignore temp readings during development. +//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000 // // Steppers @@ -86,7 +86,6 @@ // // Misc. Functions // -#define SDPOWER -1 #define SDSS PA15 #define LED_PIN PB2 @@ -255,7 +254,7 @@ // Beeper on AUX-4 #define BEEPER_PIN 33 - // buttons are directly attached using AUX-2 + // buttons are directly attached to AUX-2 #if ENABLED(REPRAPWORLD_KEYPAD) #define BTN_EN1 64 #define BTN_EN2 59 @@ -284,7 +283,3 @@ #endif // NEWPANEL #endif // HAS_SPI_LCD - -#define U_MIN_PIN -1 -#define V_MIN_PIN -1 -#define W_MIN_PIN -1 diff --git a/Marlin/src/pins/stm32/pins_BIGTREE_SKR_E3_DIP.h b/Marlin/src/pins/stm32/pins_BIGTREE_SKR_E3_DIP.h new file mode 100644 index 0000000000..dc2cd1ce60 --- /dev/null +++ b/Marlin/src/pins/stm32/pins_BIGTREE_SKR_E3_DIP.h @@ -0,0 +1,183 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +#ifndef TARGET_STM32F1 + #error "Oops! Select an STM32F1 board in 'Tools > Board.'" +#endif + +#define BOARD_NAME "BIGTREE SKR E3 DIP V1.0" + +// Release PB3/PB4 (TMC_SW Pins) from JTAG pins +#define DISABLE_JTAG + +// Ignore temp readings during development. +//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000 + +// +// Servos +// +#define SERVO0_PIN PA1 + +// +// Limit Switches +// +#define X_STOP_PIN PC1 +#define Y_STOP_PIN PC0 +#define Z_STOP_PIN PC15 + +// +// Z Probe must be this pin +// +#define Z_MIN_PROBE_PIN PC14 + +// +// Filament Runout Sensor +// +#ifndef FIL_RUNOUT_PIN + #define FIL_RUNOUT_PIN PC2 +#endif + +// +// Steppers +// +#define X_ENABLE_PIN PC7 +#define X_STEP_PIN PC6 +#define X_DIR_PIN PB15 +#ifndef X_CS_PIN + #define X_CS_PIN PC10 +#endif + +#define Y_ENABLE_PIN PB14 +#define Y_STEP_PIN PB13 +#define Y_DIR_PIN PB12 +#ifndef Y_CS_PIN + #define Y_CS_PIN PC11 +#endif + +#define Z_ENABLE_PIN PB11 +#define Z_STEP_PIN PB10 +#define Z_DIR_PIN PB2 +#ifndef Z_CS_PIN + #define Z_CS_PIN PC12 +#endif + +#define E0_ENABLE_PIN PB1 +#define E0_STEP_PIN PB0 +#define E0_DIR_PIN PC5 +#ifndef E0_CS_PIN + #define E0_CS_PIN PD2 +#endif + +// +// Software SPI pins for TMC2130 stepper drivers +// +#if ENABLED(TMC_USE_SW_SPI) + #ifndef TMC_SW_MOSI + #define TMC_SW_MOSI PB5 + #endif + #ifndef TMC_SW_MISO + #define TMC_SW_MISO PB4 + #endif + #ifndef TMC_SW_SCK + #define TMC_SW_SCK PB3 + #endif +#endif + +#if HAS_TMC220x + /** + * TMC2208/TMC2209 stepper drivers + * + * Hardware serial communication ports. + * If undefined software serial is used according to the pins below + */ + //#define X_HARDWARE_SERIAL Serial1 + //#define Y_HARDWARE_SERIAL Serial1 + //#define Z_HARDWARE_SERIAL Serial1 + //#define E0_HARDWARE_SERIAL Serial1 + + // + // Software serial + // + #define X_SERIAL_TX_PIN PC10 + #define X_SERIAL_RX_PIN PC10 + + #define Y_SERIAL_TX_PIN PC11 + #define Y_SERIAL_RX_PIN PC11 + + #define Z_SERIAL_TX_PIN PC12 + #define Z_SERIAL_RX_PIN PC12 + + #define E0_SERIAL_TX_PIN PD2 + #define E0_SERIAL_RX_PIN PD2 + +#endif + +// +// Temperature Sensors +// +#define TEMP_0_PIN PA0 // Analog Input +#define TEMP_BED_PIN PC3 // Analog Input + +// +// Heaters / Fans +// +#define HEATER_0_PIN PC8 // EXTRUDER +#define HEATER_BED_PIN PC9 // BED +#define FAN_PIN PA8 + +// +// USB connect control +// +#define USB_CONNECT_PIN PC13 +#define USB_CONNECT_INVERTING false + +#define SD_DETECT_PIN PC4 + +/** + * _____ + * 5V | · · | GND + * (LCD_EN) PB7 | · · | PB8 (LCD_RS) + * (LCD_D4) PB9 | · · | PA10 (BTN_EN2) + * RESET | · · | PA9 (BTN_EN1) + * (BTN_ENC) PB6 | · · | PA15 (BEEPER) + * ----- + * EXP1 + */ +#if HAS_SPI_LCD + #define BEEPER_PIN PA15 + #define BTN_ENC PB6 + + #if ENABLED(CR10_STOCKDISPLAY) + #define LCD_PINS_RS PB8 + + #define BTN_EN1 PA9 + #define BTN_EN2 PA10 + + #define LCD_PINS_ENABLE PB7 + #define LCD_PINS_D4 PB9 + + #else + #error "Only CR10_STOCKDISPLAY is currently supported on the BIGTREE_SKR_E3_DIP." + #endif + +#endif // HAS_SPI_LCD diff --git a/Marlin/src/pins/pins_BIGTREE_SKR_MINI_E3.h b/Marlin/src/pins/stm32/pins_BIGTREE_SKR_MINI_E3.h similarity index 90% rename from Marlin/src/pins/pins_BIGTREE_SKR_MINI_E3.h rename to Marlin/src/pins/stm32/pins_BIGTREE_SKR_MINI_E3.h index 34f686ef68..57331e65f9 100644 --- a/Marlin/src/pins/pins_BIGTREE_SKR_MINI_E3.h +++ b/Marlin/src/pins/stm32/pins_BIGTREE_SKR_MINI_E3.h @@ -1,9 +1,9 @@ /** * Marlin 3D Printer Firmware - * Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. - * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -19,20 +19,19 @@ * along with this program. If not, see . * */ +#pragma once #ifndef TARGET_STM32F1 #error "Oops! Select an STM32F1 board in 'Tools > Board.'" #endif -#ifndef BOARD_NAME - #define BOARD_NAME "BIGTREE SKR MINI E3" -#endif +#define BOARD_NAME "BIGTREE SKR Mini E3" // Release PB3/PB4 (E0 STP/DIR) from JTAG pins #define DISABLE_JTAG -// Ignore temp readings during develpment. -//#define BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE +// Ignore temp readings during development. +//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000 // // Servos @@ -104,7 +103,7 @@ // // USB connect control // -#define USB_CONNECT PC13 +#define USB_CONNECT_PIN PC13 #define USB_CONNECT_INVERTING false #define SD_DETECT_PIN PC4 diff --git a/Marlin/src/pins/pins_BIGTREE_SKR_MINI_V1_1.h b/Marlin/src/pins/stm32/pins_BIGTREE_SKR_MINI_V1_1.h similarity index 93% rename from Marlin/src/pins/pins_BIGTREE_SKR_MINI_V1_1.h rename to Marlin/src/pins/stm32/pins_BIGTREE_SKR_MINI_V1_1.h index 35544950e1..cabfc254fb 100644 --- a/Marlin/src/pins/pins_BIGTREE_SKR_MINI_V1_1.h +++ b/Marlin/src/pins/stm32/pins_BIGTREE_SKR_MINI_V1_1.h @@ -25,15 +25,13 @@ #error "Oops! Select an STM32F1 board in 'Tools > Board.'" #endif -#ifndef BOARD_NAME - #define BOARD_NAME "BIGTREE SKR mini V1.1" -#endif +#define BOARD_NAME "BIGTREE SKR Mini 1.1" //#define DISABLE_DEBUG #define DISABLE_JTAG -// Ignore temp readings during develpment. -//#define BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE +// Ignore temp readings during development. +//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000 // // Limit Switches @@ -66,9 +64,15 @@ #define E0_ENABLE_PIN PC4 #if ENABLED(TMC_USE_SW_SPI) - #define TMC_SW_SCK PB3 - #define TMC_SW_MISO PB4 - #define TMC_SW_MOSI PB5 + #ifndef TMC_SW_MOSI + #define TMC_SW_SCK PB3 + #endif + #ifndef TMC_SW_MISO + #define TMC_SW_MISO PB4 + #endif + #ifndef TMC_SW_SCK + #define TMC_SW_MOSI PB5 + #endif #endif // diff --git a/Marlin/src/pins/stm32/pins_BIGTREE_SKR_PRO_V1.1.h b/Marlin/src/pins/stm32/pins_BIGTREE_SKR_PRO_V1.1.h new file mode 100644 index 0000000000..840bbb8eed --- /dev/null +++ b/Marlin/src/pins/stm32/pins_BIGTREE_SKR_PRO_V1.1.h @@ -0,0 +1,244 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +#ifndef TARGET_STM32F4 + #error "Oops! Select an STM32F4 board in 'Tools > Board.'" +#elif HOTENDS > 3 || E_STEPPERS > 3 + #error "BIGTREE SKR Pro V1.1 supports up to 3 hotends / E-steppers." +#endif + +#define BOARD_NAME "BIGTREE SKR Pro 1.1" + +// Use one of these or SDCard-based Emulation will be used +//#define SRAM_EEPROM_EMULATION // Use BackSRAM-based EEPROM emulation +//#define FLASH_EEPROM_EMULATION // Use Flash-based EEPROM emulation + +// +// Servos +// +#define SERVO0_PIN PA1 + +// +// Limit Switches +// +#define X_MIN_PIN PB10 +#define X_MAX_PIN PE15 +#define Y_MIN_PIN PE12 +#define Y_MAX_PIN PE10 +#define Z_MIN_PIN PG8 +#define Z_MAX_PIN PG5 + +// +// Z Probe must be this pins +// +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN PA2 +#endif + +// +// Steppers +// +#define X_STEP_PIN PE9 +#define X_DIR_PIN PF1 +#define X_ENABLE_PIN PF2 +#ifndef X_CS_PIN + #define X_CS_PIN PA15 +#endif + +#define Y_STEP_PIN PE11 +#define Y_DIR_PIN PE8 +#define Y_ENABLE_PIN PD7 + #ifndef Y_CS_PIN + #define Y_CS_PIN PB8 +#endif + +#define Z_STEP_PIN PE13 +#define Z_DIR_PIN PC2 +#define Z_ENABLE_PIN PC0 +#ifndef Z_CS_PIN + #define Z_CS_PIN PB9 +#endif + +#define E0_STEP_PIN PE14 +#define E0_DIR_PIN PA0 +#define E0_ENABLE_PIN PC3 +#ifndef E0_CS_PIN + #define E0_CS_PIN PB3 +#endif + +#define E1_STEP_PIN PD15 +#define E1_DIR_PIN PE7 +#define E1_ENABLE_PIN PA3 +#ifndef E1_CS_PIN + #define E1_CS_PIN PG15 +#endif + +#define E2_STEP_PIN PD13 +#define E2_DIR_PIN PG9 +#define E2_ENABLE_PIN PF0 +#ifndef E2_CS_PIN + #define E2_CS_PIN PG12 +#endif + +// +// Software SPI pins for TMC2130 stepper drivers +// +#if ENABLED(TMC_USE_SW_SPI) + #ifndef TMC_SW_MOSI + #define TMC_SW_MOSI PC12 + #endif + #ifndef TMC_SW_MISO + #define TMC_SW_MISO PC11 + #endif + #ifndef TMC_SW_SCK + #define TMC_SW_SCK PC10 + #endif +#endif + +#if HAS_TMC220x + /** + * TMC2208/TMC2209 stepper drivers + * + * Hardware serial communication ports. + * If undefined software serial is used according to the pins below + */ + //#define X_HARDWARE_SERIAL Serial + //#define X2_HARDWARE_SERIAL Serial1 + //#define Y_HARDWARE_SERIAL Serial1 + //#define Y2_HARDWARE_SERIAL Serial1 + //#define Z_HARDWARE_SERIAL Serial1 + //#define Z2_HARDWARE_SERIAL Serial1 + //#define E0_HARDWARE_SERIAL Serial1 + //#define E1_HARDWARE_SERIAL Serial1 + //#define E2_HARDWARE_SERIAL Serial1 + //#define E3_HARDWARE_SERIAL Serial1 + //#define E4_HARDWARE_SERIAL Serial1 + + // + // Software serial + // + #define X_SERIAL_TX_PIN PC13 + #define X_SERIAL_RX_PIN PC13 + + #define Y_SERIAL_TX_PIN PE3 + #define Y_SERIAL_RX_PIN PE3 + + #define Z_SERIAL_TX_PIN PE1 + #define Z_SERIAL_RX_PIN PE1 + + #define E0_SERIAL_TX_PIN PD4 + #define E0_SERIAL_RX_PIN PD4 + + #define E1_SERIAL_TX_PIN PD1 + #define E1_SERIAL_RX_PIN PD1 + + #define E2_SERIAL_TX_PIN PD6 + #define E2_SERIAL_RX_PIN PD6 +#endif + +// +// Temperature Sensors +// +#define TEMP_0_PIN PF4 // T1 <-> E0 +#define TEMP_1_PIN PF5 // T2 <-> E1 +#define TEMP_2_PIN PF6 // T3 <-> E2 +#define TEMP_BED_PIN PF3 // T0 <-> Bed + +// +// Heaters / Fans +// +#define HEATER_0_PIN PB1 // Heater0 +#define HEATER_1_PIN PD14 // Heater1 +#define HEATER_2_PIN PB0 // Heater1 +#define HEATER_BED_PIN PD12 // Hotbed +#define FAN_PIN PC8 // Fan0 +#define FAN1_PIN PE5 // Fan1 +#define FAN2_PIN PE6 // Fan2 + +// +// Misc. Functions +// +#define SDSS PB12 + +/** + * _____ _____ + * NC | · · | GND 5V | · · | GND + * RESET | · · | PF12(SD_DETECT) (LCD_D7) PG7 | · · | PG6 (LCD_D6) + * (MOSI)PB15 | · · | PF11(BTN_EN2) (LCD_D5) PG3 | · · | PG2 (LCD_D4) + * (SD_SS)PB12 | · · | PG10(BTN_EN1) (LCD_RS) PD10 | · · | PD11 (LCD_EN) + * (SCK)PB13 | · · | PB14(MISO) (BTN_ENC) PA8 | · · | PG4 (BEEPER) + * ￣￣ ￣￣ + * EXP2 EXP1 + */ + +// +// LCDs and Controllers +// +#if HAS_SPI_LCD + #define BEEPER_PIN PG4 + #define BTN_ENC PA8 + + #if ENABLED(CR10_STOCKDISPLAY) + #define LCD_PINS_RS PG6 + + #define BTN_EN1 PD11 + #define BTN_EN2 PG2 + + #define LCD_PINS_ENABLE PG7 + #define LCD_PINS_D4 PG3 + + #else + + #define LCD_PINS_RS PD10 + + #define BTN_EN1 PG10 + #define BTN_EN2 PF11 + #define SD_DETECT_PIN PF12 + + #define LCD_SDSS PB12 + + #define LCD_PINS_ENABLE PD11 + #define LCD_PINS_D4 PG2 + + #if ENABLED(ULTIPANEL) + #define LCD_PINS_D5 PG3 + #define LCD_PINS_D6 PG6 + #define LCD_PINS_D7 PG7 + #endif + + #endif + + // Alter timing for graphical display + #if HAS_GRAPHICAL_LCD + #ifndef ST7920_DELAY_1 + #define ST7920_DELAY_1 DELAY_NS(96) + #endif + #ifndef ST7920_DELAY_2 + #define ST7920_DELAY_2 DELAY_NS(48) + #endif + #ifndef ST7920_DELAY_3 + #define ST7920_DELAY_3 DELAY_NS(600) + #endif + #endif + +#endif // HAS_SPI_LCD diff --git a/Marlin/src/pins/pins_BLACK_STM32F407VE.h b/Marlin/src/pins/stm32/pins_BLACK_STM32F407VE.h similarity index 94% rename from Marlin/src/pins/pins_BLACK_STM32F407VE.h rename to Marlin/src/pins/stm32/pins_BLACK_STM32F407VE.h index 026648589e..3edc77460b 100644 --- a/Marlin/src/pins/pins_BLACK_STM32F407VE.h +++ b/Marlin/src/pins/stm32/pins_BLACK_STM32F407VE.h @@ -27,22 +27,21 @@ * Shield - https://github.com/jmz52/Hardware */ -#pragma once - #if !defined(STM32F4) && !defined(STM32F4xx) #error "Oops! Select an STM32F4 board in 'Tools > Board.'" +#elif HOTENDS > 2 || E_STEPPERS > 2 + #error "Black STM32F4VET6 supports up to 2 hotends / E-steppers." +#endif + +#ifndef BOARD_NAME + #define BOARD_NAME "Black STM32F4VET6" #endif #define DEFAULT_MACHINE_NAME "STM32F407VET6" -//#define BOARD_NAME "Black STM32F4VET6" //#define I2C_EEPROM -//#define E2END 0x1FFF // EEPROM end address (8kB) -#define EEPROM_EMULATED_WITH_SRAM - -#if HOTENDS > 2 || E_STEPPERS > 2 - #error "Black STM32F4VET6 supports up to 2 hotends / E-steppers." -#endif +//#define E2END 0x1FFF // 8KB +#define SRAM_EEPROM_EMULATION // // Servos diff --git a/Marlin/src/pins/pins_CHITU3D.h b/Marlin/src/pins/stm32/pins_CHITU3D.h similarity index 96% rename from Marlin/src/pins/pins_CHITU3D.h rename to Marlin/src/pins/stm32/pins_CHITU3D.h index 59f6b66bb7..7a42dc9e4e 100644 --- a/Marlin/src/pins/pins_CHITU3D.h +++ b/Marlin/src/pins/stm32/pins_CHITU3D.h @@ -29,14 +29,14 @@ * 2017 Victor Perez Marlin for stm32f1 test */ +#define BOARD_NAME "Chitu3D" #define DEFAULT_MACHINE_NAME "STM32F103RET6" -#define BOARD_NAME "Chitu3d Marlin" // Enable I2C_EEPROM for testing //#define I2C_EEPROM -// Ignore temp readings during develpment. -#define BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE +// Ignore temp readings during development. +//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000 // // Steppers @@ -84,7 +84,6 @@ // // Misc. Functions // -#define SDPOWER -1 #define SDSS -1 #define LED_PIN -1 #define CASE_LIGHT_PIN 8 @@ -253,7 +252,7 @@ // Beeper on AUX-4 #define BEEPER_PIN 33 - // buttons are directly attached using AUX-2 + // buttons are directly attached to AUX-2 #if ENABLED(REPRAPWORLD_KEYPAD) #define BTN_EN1 64 #define BTN_EN2 59 @@ -282,7 +281,3 @@ #endif // NEWPANEL #endif // HAS_SPI_LCD - -#define U_MIN_PIN -1 -#define V_MIN_PIN -1 -#define W_MIN_PIN -1 diff --git a/Marlin/src/pins/pins_FYSETC_AIO_II.h b/Marlin/src/pins/stm32/pins_FYSETC_AIO_II.h similarity index 94% rename from Marlin/src/pins/pins_FYSETC_AIO_II.h rename to Marlin/src/pins/stm32/pins_FYSETC_AIO_II.h index 49879ba50d..ed44f94717 100644 --- a/Marlin/src/pins/pins_FYSETC_AIO_II.h +++ b/Marlin/src/pins/stm32/pins_FYSETC_AIO_II.h @@ -28,10 +28,12 @@ #define BOARD_NAME "FYSETC AIO II" #define BOARD_WEBSITE_URL "https://fysetc.com" +#define DISABLE_JTAG + #define pins_v2_20190128 // geo-f:add for new pins define -// Ignore temp readings during develpment. -#define BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE +// Ignore temp readings during development. +//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000 // // Limit Switches @@ -77,11 +79,11 @@ // // X:PA2 Y:PA3 Z:PB12 E:PB13 // changed for test -#define MOTOR_CURRENT_PWM_XY_PIN PA3 -#define MOTOR_CURRENT_PWM_Z_PIN PA2 // PB12 +//#define MOTOR_CURRENT_PWM_XY_PIN PA3 +//#define MOTOR_CURRENT_PWM_Z_PIN PA2 // PB12 //#define MOTOR_CURRENT_PWM_XY_PIN PB6 //#define MOTOR_CURRENT_PWM_Z_PIN PB7 // PB12 -#define MOTOR_CURRENT_PWM_E_PIN -1 // PB13 +//#define MOTOR_CURRENT_PWM_E_PIN -1 // PB13 // Motor current PWM conversion, PWM value = MotorCurrentSetting * 255 / range #ifndef MOTOR_CURRENT_PWM_RANGE #define MOTOR_CURRENT_PWM_RANGE 1500 // geo-f:old 2000 diff --git a/Marlin/src/pins/pins_FYSETC_CHEETAH.h b/Marlin/src/pins/stm32/pins_FYSETC_CHEETAH.h similarity index 94% rename from Marlin/src/pins/pins_FYSETC_CHEETAH.h rename to Marlin/src/pins/stm32/pins_FYSETC_CHEETAH.h index c3be9431a2..e3aac9e84a 100644 --- a/Marlin/src/pins/pins_FYSETC_CHEETAH.h +++ b/Marlin/src/pins/stm32/pins_FYSETC_CHEETAH.h @@ -27,11 +27,13 @@ #define DEFAULT_MACHINE_NAME "3D Printer" -#define BOARD_NAME "FYSETC CHEETAH" +#define BOARD_NAME "FYSETC Cheetah" #define BOARD_WEBSITE_URL "https://fysetc.com" -// Ignore temp readings during develpment. -#define BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE +// Ignore temp readings during development. +//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000 + +#define DISABLE_JTAG // // Servos @@ -69,7 +71,7 @@ #define E0_DIR_PIN PC14 #define E0_ENABLE_PIN PC13 -#define X_HARDWARE_SERIAL MSerial2 // Port correct? +#define X_HARDWARE_SERIAL MSerial2 #define Y_HARDWARE_SERIAL MSerial2 #define Z_HARDWARE_SERIAL MSerial2 #define E0_HARDWARE_SERIAL MSerial2 diff --git a/Marlin/src/pins/stm32/pins_FYSETC_CHEETAH_V12.h b/Marlin/src/pins/stm32/pins_FYSETC_CHEETAH_V12.h new file mode 100644 index 0000000000..42d7a94292 --- /dev/null +++ b/Marlin/src/pins/stm32/pins_FYSETC_CHEETAH_V12.h @@ -0,0 +1,60 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +#ifndef __STM32F1__ + #error "Oops! Select an STM32F1 board in 'Tools > Board.'" +#endif + +#include "pins_FYSETC_CHEETAH.h" + +#undef X_HARDWARE_SERIAL +#undef Y_HARDWARE_SERIAL +#undef Z_HARDWARE_SERIAL +#undef E0_HARDWARE_SERIAL + +#undef RGB_LED_R_PIN +#undef RGB_LED_G_PIN +#undef RGB_LED_B_PIN + +#if HAS_TMC220x + + /** + * TMC2208/TMC2209 stepper drivers + */ + + // + // Software serial + // + #define X_SERIAL_TX_PIN PA11 + #define X_SERIAL_RX_PIN PA12 + + #define Y_SERIAL_TX_PIN PB6 + #define Y_SERIAL_RX_PIN PB7 + + #define Z_SERIAL_TX_PIN PB10 + #define Z_SERIAL_RX_PIN PB11 + + #define E0_SERIAL_TX_PIN PA2 + #define E0_SERIAL_RX_PIN PA3 + +#endif diff --git a/Marlin/src/pins/stm32/pins_GTM32_PRO_VB.h b/Marlin/src/pins/stm32/pins_GTM32_PRO_VB.h new file mode 100644 index 0000000000..c2f5cbc5ea --- /dev/null +++ b/Marlin/src/pins/stm32/pins_GTM32_PRO_VB.h @@ -0,0 +1,234 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * 24 May 2018 - @chepo for STM32F103VET6 + * Schematic: https://github.com/chepo92/Smartto/blob/master/circuit_diagram/Rostock301/Hardware_GTM32_PRO_VB.pdf + */ + +#ifndef __STM32F1__ + #error "Oops! Select an STM32F1 board in 'Tools > Board.'" +#endif + +#define BOARD_NAME "GTM32 Pro VB" +#define DEFAULT_MACHINE_NAME "STM32F103VET6" + +//#define DISABLE_DEBUG + +// +// It is required to disable JTAG function because its pins are +// used as GPIO to drive the Y axis stepper. +// DO NOT ENABLE! +// +#define DISABLE_JTAG + +// +// If you don't need the SWDIO functionality (any more), you may +// disable SWD here to regain PA13/PA14 pins for other use. +// +//#define DISABLE_JTAGSWD + +// Ignore temp readings during development. +//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000 + +// Enable EEPROM Emulation for this board as it doesn't have EEPROM +#define FLASH_EEPROM_EMULATION +#define E2END 0xFFF // 4KB + +// +// Limit Switches +// +#define X_MIN_PIN PE5 // ENDSTOPS 15,17 +#define X_MAX_PIN PE4 // ENDSTOPS 16,18 +#define Y_MIN_PIN PE3 // ENDSTOPS 9,11 +#define Y_MAX_PIN PE2 // ENDSTOPS 10,12 +#define Z_MIN_PIN PE1 // ENDSTOPS 3,5 +#define Z_MAX_PIN PE0 // ENDSTOPS 4,6 + +// +// Steppers +// +#define X_STEP_PIN PC6 +#define X_DIR_PIN PD13 +#define X_ENABLE_PIN PA8 + +#define Y_STEP_PIN PA12 +#define Y_DIR_PIN PA11 +#define Y_ENABLE_PIN PA15 + +#define Z_STEP_PIN PD6 +#define Z_DIR_PIN PD3 +#define Z_ENABLE_PIN PB3 + +// Extruder stepper pins +// NOTE: Numbering here is made according to EXT connector numbers, +// the FANx_PWM line numbering in the schematics is reverse. +// That is, E0_*_PIN are the E2_* lines connected to E2_A1 step +// stick that drives the EXT0 output on the board. +// +#define E0_STEP_PIN PC14 +#define E0_DIR_PIN PC13 +#define E0_ENABLE_PIN PC15 + +#define E1_STEP_PIN PA0 +#define E1_DIR_PIN PB6 +#define E1_ENABLE_PIN PA1 + +#define E2_STEP_PIN PB2 +#define E2_DIR_PIN PB11 +#define E2_ENABLE_PIN PC4 + +// +// Heaters / Fans +// +#define HEATER_0_PIN PB0 // EXT0 port +#define HEATER_1_PIN PB5 // EXT1 port +#define HEATER_2_PIN PB4 // EXT2 port +#define HEATER_BED_PIN PB1 // CON2X3 hotbed port + +// +// These are FAN PWM pins on EXT0..EXT2 connectors. +// +//#define FAN_PIN PB9 // EXT0 port +#define ORIG_E0_AUTO_FAN_PIN PB9 // EXT0 port, used as main extruder fan +#define FAN1_PIN PB8 // EXT1 port +#define FAN2_PIN PB7 // EXT2 port + +// +// Temperature Sensors +// +#define TEMP_0_PIN PC2 // EXT0 port +#define TEMP_1_PIN PC1 // EXT1 port +#define TEMP_2_PIN PC0 // EXT2 port +#define TEMP_BED_PIN PC3 // CON2X3 hotbed port + +// +// Misc. Functions +// +#define LED_PWM PD12 // External LED, pin 2 on LED labeled connector + +// +// LCD / Controller +// +#if HAS_SPI_LCD + + #if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) + // + // LCD display on J2 FFC40 + // Geeetech's LCD2004A Control Panel is very much like + // RepRapDiscount Smart Controller, but adds an FFC40 connector + // + #define LCD_PINS_RS PE6 // CS chip select /SS chip slave select + #define LCD_PINS_ENABLE PE14 // SID (MOSI) + #define LCD_PINS_D4 PD8 // SCK (CLK) clock + #define LCD_PINS_D5 PD9 + #define LCD_PINS_D6 PD10 + #define LCD_PINS_D7 PE15 + + #else + // + // Serial LCDs can be implemented in ExtUI + // + //#define LCD_UART_TX PD8 + //#define LCD_UART_RX PD9 + #endif + + #ifndef ST7920_DELAY_1 + #define ST7920_DELAY_1 DELAY_NS(96) + #endif + #ifndef ST7920_DELAY_2 + #define ST7920_DELAY_2 DELAY_NS(48) + #endif + #ifndef ST7920_DELAY_3 + #define ST7920_DELAY_3 DELAY_NS(715) + #endif + +#endif // HAS_SPI_LCD + +#if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) + // + // Geeetech's LCD2004A Control Panel is very much like + // RepRapDiscount Smart Controller, but adds an FFC40 connector + // connected with a flat wire to J2 connector on the board. + // + #define BTN_EN1 PE8 + #define BTN_EN2 PE9 + #define BTN_ENC PE13 + + #define GTM32_PRO_VB_USE_LCD_BEEPER + #define GTM32_PRO_VB_USE_EXT_SDCARD +#endif + +// +// Beeper +// +#ifdef GTM32_PRO_VB_USE_LCD_BEEPER + // This is pin 32 on J2 FFC40 and pin, goes to the beeper + // on Geeetech's version of RepRapDiscount Smart Controller + // (e.g. on Rostock 301) + #define BEEPER_PIN PE12 +#else + // This is the beeper on the board itself + #define BEEPER_PIN PB10 +#endif + +/** + * The on-board TF_CARD_SOCKET microSD card socket has no SD Detect pin wired. + * + * The FFC10 (SD_CARD) connector has the same pins as those routed to the FFC40 (J2) + * connector, which usually go to the SD Card slot on the Geeetech version of the + * RepRapDiscount Smart Controller. Both connectors have the card detect signal. + * + * The on-board SD card and the external card (on either SD_CARD or J2) are two + * separate devices and can work simultaneously. Unfortunately, Marlin only supports + * a single SPI Flash device (as of 2019-07-05) so only one is enabled here. + */ +#if ENABLED(GTM32_PRO_VB_USE_EXT_SDCARD) + // + // SD Card on RepRapDiscount Smart Controller (J2) or on SD_CARD connector + // + #define SS_PIN PC11 + #define SCK_PIN PC12 + #define MOSI_PIN PD2 + #define MISO_PIN PC8 + #define SD_DETECT_PIN PC7 +#else + // + // Use the on-board card socket labeled TF_CARD_SOCKET + // + #define SS_PIN PA4 + #define SCK_PIN PA5 + #define MOSI_PIN PA7 + #define MISO_PIN PA6 + #define SD_DETECT_PIN -1 // Card detect is not connected +#endif + +#define SDSS SS_PIN + +// +// ESP WiFi can be soldered to J9 connector which is wired to USART2. +// Must define WIFISUPPORT in Configuration.h for the printer. +// +#define ESP_WIFI_MODULE_COM 2 +#define ESP_WIFI_MODULE_BAUDRATE 115200 +#define ESP_WIFI_MODULE_RESET_PIN -1 diff --git a/Marlin/src/pins/pins_JGAURORA_A5S_A1.h b/Marlin/src/pins/stm32/pins_JGAURORA_A5S_A1.h similarity index 60% rename from Marlin/src/pins/pins_JGAURORA_A5S_A1.h rename to Marlin/src/pins/stm32/pins_JGAURORA_A5S_A1.h index 4802bb1c0f..77730bc415 100644 --- a/Marlin/src/pins/pins_JGAURORA_A5S_A1.h +++ b/Marlin/src/pins/stm32/pins_JGAURORA_A5S_A1.h @@ -22,33 +22,28 @@ #pragma once /** - * 2017 Victor Perez Marlin for stm32f1 test - * 2018 Modified by Pablo Crespo for Morpheus Board (https://github.com/pscrespo/Morpheus-STM32) - * 2019 Modified by Roberto Mariani & Samuel Pinches for JGAurora A5S & A1 Board. + * ╦╔═╗╔═╗┬ ┬┬─┐┌─┐┬─┐┌─┐╔═╗┌─┐┬─┐┬ ┬┌┬┐ ┌─┐┌─┐┌┬┐ + * ║║ ╦╠═╣│ │├┬┘│ │├┬┘├─┤╠╣ │ │├┬┘│ ││││ │ │ ││││ + * ╚╝╚═╝╩ ╩└─┘┴└─└─┘┴└─┴ ┴╚ └─┘┴└─└─┘┴ ┴o└─┘└─┘┴ ┴ + * Pin assignments for 32-bit JGAurora A5S & A1 */ -/** - * JGAurora A5S A1 Board pin assignments - */ - #ifndef __STM32F1__ #error "Oops! Select an STM32F1 board in 'Tools > Board.'" +#elif HOTENDS > 1 || E_STEPPERS > 1 + #error "JGAurora 32-bit board only supports 1 hotend / E-stepper. Comment out this line to continue." #endif - #define BOARD_NAME "JGAurora A5S A1 board" -// #define STM32_XL_DENSITY // required, but should be set by platformio flags, not here! (why? not sure.) +#define STM32_XL_DENSITY +// #define MCU_STM32F103ZE // not yet required +// Enable EEPROM Emulation for this board, so that we don't overwrite factory data -//#define MCU_STM32F103ZE // not yet required - -// // I2C EEPROM with 64K of space - AT24C64 -// #define I2C_EEPROM -// #define E2END 0x7FFF - -// Enable EEPROM Emulation for this board - -//#define FLASH_EEPROM_EMULATION 1 -//#define E2END 0xFFF //((uint32)(EEPROM_START_ADDRESS + EEPROM_PAGE_SIZE + EEPROM_PAGE_SIZE)) // not 0xFFF +//#define I2C_EEPROM // AT24C64 +//#define E2END 0x7FFF // 64KB +//#define FLASH_EEPROM_EMULATION +//#define E2END 0xFFF // 4KB +//#define E2END uint32(EEPROM_START_ADDRESS + (EEPROM_PAGE_SIZE * 2) - 1) //#define EEPROM_CHITCHAT //#define DEBUG_EEPROM_READWRITE @@ -58,6 +53,9 @@ #define X_STOP_PIN PC6 #define Y_STOP_PIN PG8 #define Z_STOP_PIN PG7 +//#define X_MAX_PIN PC5 +//#define Y_MAX_PIN PC4 +//#define Z_MAX_PIN PB0 // // Steppers @@ -96,7 +94,6 @@ #define FAN_PIN PA1 -#define PS_ON_PIN PA0 #define FIL_RUNOUT_PIN PC7 // @@ -106,6 +103,10 @@ #define FSMC_CS_PIN PD7 #define FSMC_RS_PIN PG0 +#define LCD_USE_DMA_FSMC // Use DMA transfers to send data to the TFT +#define FSMC_DMA_DEV DMA2 +#define FSMC_DMA_CHANNEL DMA_CH5 + // // SD Card // @@ -117,10 +118,11 @@ #define BEEPER_PIN PC3 // use PB7 to shut up if desired #define LED_PIN PC13 +// // Touch support -#define BTN_ENC PA11 // Real pin is needed to enable encoder's push button functionality used by touch screen. PA11 gives stable value. - -#define TOUCH_CS PA4 -//#define TOUCH_INTERRUPT PC4 // Not yet implemented - -#define NO_PAUSE_AFTER_PRINT +// +#if ENABLED(TOUCH_BUTTONS) + #define BTN_ENC PA11 // Real pin needed to enable encoder's push button functionality used by touch screen. PA11 gives stable value. + #define TOUCH_CS_PIN PA4 + #define TOUCH_INT_PIN PC4 +#endif diff --git a/Marlin/src/pins/stm32/pins_LONGER3D_LK.h b/Marlin/src/pins/stm32/pins_LONGER3D_LK.h new file mode 100644 index 0000000000..5be4eb57de --- /dev/null +++ b/Marlin/src/pins/stm32/pins_LONGER3D_LK.h @@ -0,0 +1,158 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Longer3D LK1/LK2 & Alfawise U20/U30 (STM32F103VET6) board pin assignments + */ + +#if !defined(__STM32F1__) && !defined(STM32F1xx) + #error "Oops! Select a STM32F1 board in 'Tools > Board.'" +#elif HOTENDS > 1 || E_STEPPERS > 1 + #error "Longer3D board only supports 1 hotend / E-stepper. Comment out this line to continue." +#endif + +#define BOARD_NAME "Longer3D" +#define ALFAWISE_UX0 // Common to all Longer3D STM32F1 boards (used for Open drain mosfets) + +//#define DISABLE_DEBUG // We still want to debug with STLINK... +#define DISABLE_JTAG // We free the jtag pins (PA15) but keep STLINK + // Release PB4 (STEP_X_PIN) from JTAG NRST role. +// +// Limit Switches +// +#define X_MIN_PIN PC1 // pin 16 +#define X_MAX_PIN PC0 // pin 15 (Filament sensor on Alfawise setup) +#define Y_MIN_PIN PC15 // pin 9 +#define Y_MAX_PIN PC14 // pin 8 (Unused in stock Alfawise setup) +#define Z_MIN_PIN PE6 // pin 5 Standard Endstop or Z_Probe endstop function +#define Z_MAX_PIN PE5 // pin 4 (Unused in stock Alfawise setup) + // May be used for BLTouch Servo function on older variants (<= V08) + +// +// Filament Sensor +// +#ifndef FIL_RUNOUT_PIN + #define FIL_RUNOUT_PIN PC0 // XMAX plug on PCB used as filament runout sensor on Alfawise boards (inverting true) +#endif + +// +// Steppers +// +#define X_ENABLE_PIN PB5 // pin 91 +#define X_STEP_PIN PB4 // pin 90 +#define X_DIR_PIN PB3 // pin 89 + +#define Y_ENABLE_PIN PB8 // pin 95 +#define Y_STEP_PIN PB7 // pin 93 +#define Y_DIR_PIN PB6 // pin 92 + +#define Z_ENABLE_PIN PE1 // pin 98 +#define Z_STEP_PIN PE0 // pin 97 +#define Z_DIR_PIN PB9 // pin 96 + +#define E0_ENABLE_PIN PE4 // pin 3 +#define E0_STEP_PIN PE3 // pin 2 +#define E0_DIR_PIN PE2 // pin 1 + +// +// Temperature Sensors +// +#define TEMP_0_PIN PA0 // pin 23 (Nozzle 100K/3950 thermistor) +#define TEMP_BED_PIN PA1 // pin 24 (Hot Bed 100K/3950 thermistor) + +// +// Heaters / Fans +// +#define HEATER_0_PIN PD3 // pin 84 (Nozzle Heat Mosfet) +#define HEATER_BED_PIN PA8 // pin 67 (Hot Bed Mosfet) + +#define FAN_PIN PA15 // pin 77 (4cm Fan) +#define FAN_SOFT_PWM // Required to avoid issues with heating or STLink +#define FAN_MIN_PWM 35 // Fan will not start in 1-30 range +#define FAN_MAX_PWM 255 + +//#define BEEPER_PIN PD13 // pin 60 (Servo PWM output 5V/GND on Board V0G+) made for BL-Touch sensor + // Can drive a PC Buzzer, if connected between PWM and 5V pins + +#define LED_PIN PC2 // pin 17 + +// +// PWM +// +#define SERVO0_PIN PD13 // Open drain PWM pin on the V0G (GND or floating 5V) +#define SERVO0_PWM_OD // Comment this if using PE5 + +//#define SERVO0_PIN PE5 // Pulled up PWM pin on the V08 (3.3V or 0) + +/** + * Note: Alfawise screens use various TFT controllers. Supported screens + * are based on the ILI9341, ILI9328 and ST7798V. Define init sequences for + * other screens in u8g_dev_tft_320x240_upscale_from_128x64.cpp + * + * If the screen stays white, disable 'LCD_RESET_PIN' to let the bootloader + * init the screen. + * + * Setting an 'LCD_RESET_PIN' may cause a flicker when entering the LCD menu + * because Marlin uses the reset as a failsafe to revive a glitchy LCD. + */ + +#define LCD_RESET_PIN PC4 // pin 33 +#define LCD_BACKLIGHT_PIN PD12 // pin 59 +#define FSMC_CS_PIN PD7 // pin 88 = FSMC_NE1 +#define FSMC_RS_PIN PD11 // pin 58 A16 Register. Only one address needed + +#define LCD_USE_DMA_FSMC // Use DMA transfers to send data to the TFT +#define FSMC_DMA_DEV DMA2 +#define FSMC_DMA_CHANNEL DMA_CH5 + +#define DOGLCD_MOSI -1 // Prevent auto-define by Conditionals_post.h +#define DOGLCD_SCK -1 + +/** + * Note: Alfawise U20/U30 boards DON'T use SPI2, as the hardware designer + * mixed up MOSI and MISO pins. SPI is managed in SW, and needs pins + * declared below. + */ +#if ENABLED(TOUCH_BUTTONS) + #define TOUCH_CS_PIN PB12 // pin 51 SPI2_NSS + #define TOUCH_SCK_PIN PB13 // pin 52 + #define TOUCH_MOSI_PIN PB14 // pin 53 + #define TOUCH_MISO_PIN PB15 // pin 54 + #define TOUCH_INT_PIN PC6 // pin 63 (PenIRQ coming from ADS7843) + + #define BTN_ENC PB0 // pin 35 unconnected pin on Alfawise. (PC13 to try) + #define BTN_EN1 -1 // Real pin is needed to enable encoder's push button + #define BTN_EN2 -1 // functionality used by touch screen +#endif + +// +// SPI1 (EEPROM W25Q64 + DAC OUT) +// +#undef E2END +#define E2END 0x7FF // EEPROM end address (reserve 2kB on sd/sram, real spi one is 8MB/64Mbits) +/* +#define SPI_EEPROM 1 // If commented this will create a file on the SD card as a replacement +#define SPI_CHAN_EEPROM1 1 +#define SPI_EEPROM1_CS PC5 // pin 34 + +//#define EEPROM_SCK BOARD_SPI1_SCK_PIN // PA5 pin 30 +//#define EEPROM_MISO BOARD_SPI1_MISO_PIN // PA6 pin 31 +//#define EEPROM_MOSI BOARD_SPI1_MOSI_PIN // PA7 pin 32 +*/ diff --git a/Marlin/src/pins/pins_MALYAN_M200.h b/Marlin/src/pins/stm32/pins_MALYAN_M200.h similarity index 98% rename from Marlin/src/pins/pins_MALYAN_M200.h rename to Marlin/src/pins/stm32/pins_MALYAN_M200.h index 63d0b8f9a2..0d15441ad3 100644 --- a/Marlin/src/pins/pins_MALYAN_M200.h +++ b/Marlin/src/pins/stm32/pins_MALYAN_M200.h @@ -29,7 +29,7 @@ #error "Oops! You must be compiling for STM32." #endif -#define BOARD_NAME "MALYANM200" +#define BOARD_NAME "Malyan M200" // Enable EEPROM Emulation for this board // This setting should probably be in configuration.h diff --git a/Marlin/src/pins/pins_MKS_ROBIN.h b/Marlin/src/pins/stm32/pins_MKS_ROBIN.h similarity index 86% rename from Marlin/src/pins/pins_MKS_ROBIN.h rename to Marlin/src/pins/stm32/pins_MKS_ROBIN.h index 6dac3f65c4..dd43383c0e 100644 --- a/Marlin/src/pins/pins_MKS_ROBIN.h +++ b/Marlin/src/pins/stm32/pins_MKS_ROBIN.h @@ -27,9 +27,7 @@ #ifndef __STM32F1__ #error "Oops! Select an STM32F1 board in 'Tools > Board.'" -#endif - -#if HOTENDS > 2 || E_STEPPERS > 2 +#elif HOTENDS > 2 || E_STEPPERS > 2 #error "MKS Robin supports up to 2 hotends / E-steppers. Comment out this line to continue." #endif @@ -111,11 +109,15 @@ #define LED_PIN PB2 /** - * Note: MKS Robin TFT screens may have different TFT controllers - * If the screen stays white, disable 'LCD_RESET_PIN' to rely on the bootloader to do screen initialization. + * Note: MKS Robin TFT screens use various TFT controllers. Supported screens + * are based on the ILI9342, ILI9328 and ST7798V. Define init sequences for + * other screens in u8g_dev_tft_320x240_upscale_from_128x64.cpp * - * Enabling 'LCD_RESET_PIN' causes flickering when entering the LCD menu due to LCD controller reset. - * Reset feature was designed to "revive the LCD if static electricity killed it." + * If the screen stays white, disable 'LCD_RESET_PIN' + * to let the bootloader init the screen. + * + * Setting an 'LCD_RESET_PIN' may cause a flicker when entering the LCD menu + * because Marlin uses the reset as a failsafe to revive a glitchy LCD. */ //#define LCD_RESET_PIN PF6 #define LCD_BACKLIGHT_PIN PG11 diff --git a/Marlin/src/pins/stm32/pins_MKS_ROBIN_LITE.h b/Marlin/src/pins/stm32/pins_MKS_ROBIN_LITE.h new file mode 100644 index 0000000000..9a6901d17a --- /dev/null +++ b/Marlin/src/pins/stm32/pins_MKS_ROBIN_LITE.h @@ -0,0 +1,143 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +#ifndef __STM32F1__ + #error "Oops! Select an STM32F1 board in 'Tools > Board.'" +#endif + +#if HOTENDS > 1 || E_STEPPERS > 1 + #error "MKS Robin Lite supports up to 1 hotends / E-steppers. Comment out this line to continue." +#endif + +#ifndef BOARD_NAME + #define BOARD_NAME "MKS Robin Lite" +#endif +#define BOARD_WEBSITE_URL "https://github.com/makerbase-mks" + +//#define DISABLE_DEBUG +#define DISABLE_JTAG +#define ENABLE_SPI2 + +// +// Limit Switches +// +#define X_STOP_PIN PC13 +#define Y_STOP_PIN PC0 +#define Z_MIN_PIN PC12 +#define Z_MAX_PIN PB9 + +// +// Steppers +// +#define X_STEP_PIN PC6 +#define X_DIR_PIN PB12 +#define X_ENABLE_PIN PB10 + +#define Y_STEP_PIN PB11 +#define Y_DIR_PIN PB2 +#define Y_ENABLE_PIN PB10 + +#define Z_STEP_PIN PB1 +#define Z_DIR_PIN PC5 +#define Z_ENABLE_PIN PB10 + +#define E0_STEP_PIN PC4 +#define E0_DIR_PIN PA5 +#define E0_ENABLE_PIN PA4 + +// +// Heaters / Fans +// +#define HEATER_0_PIN PC9 +#define FAN_PIN PA8 +#define HEATER_BED_PIN PC8 + +// +// Temperature Sensors +// +#define TEMP_BED_PIN PA1 +#define TEMP_0_PIN PA0 + +#define FIL_RUNOUT_PIN PB8 // MT_DET + +// +// LCD Pins +// +#if HAS_SPI_LCD + #define BEEPER_PIN PD2 + #define BTN_ENC PB3 + #define LCD_PINS_RS PC3 + + #define BTN_EN1 PB5 + #define BTN_EN2 PB4 + + #define LCD_PINS_ENABLE PC2 + + #if ENABLED(MKS_MINI_12864) + + #define LCD_BACKLIGHT_PIN -1 + #define LCD_RESET_PIN -1 + #define DOGLCD_A0 PC1 + #define DOGLCD_CS PC2 + #define DOGLCD_SCK PB13 + #define DOGLCD_MOSI PB15 + + #else // !MKS_MINI_12864 + + #define LCD_PINS_D4 PC1 + #if ENABLED(ULTIPANEL) + #define LCD_PINS_D5 -1 + #define LCD_PINS_D6 -1 + #define LCD_PINS_D7 -1 + #endif + + #endif // !MKS_MINI_12864 + +#endif // HAS_SPI_LCD + +// Motor current PWM pins +#define MOTOR_CURRENT_PWM_XY_PIN PB0 +#define MOTOR_CURRENT_PWM_Z_PIN PA7 +#define MOTOR_CURRENT_PWM_E_PIN PA6 +#define MOTOR_CURRENT_PWM_RANGE (65535/10/3.3) // (255 * (1000mA / 65535)) * 257 = 1000 is equal 1.6v Vref in turn equal 1Amp +#define DEFAULT_PWM_MOTOR_CURRENT { 1000, 1000, 1000 } // 1.05Amp per driver, here is XY, Z and E. This values determined empirically. + +// +// SD Card +// +#define ENABLE_SPI2 +#define SD_DETECT_PIN PC10 +#define SCK_PIN PB13 +#define MISO_PIN P1B4 +#define MOSI_PIN P1B5 +#define SS_PIN PA15 + +#ifndef ST7920_DELAY_1 + #define ST7920_DELAY_1 DELAY_NS(125) +#endif +#ifndef ST7920_DELAY_2 + #define ST7920_DELAY_2 DELAY_NS(125) +#endif +#ifndef ST7920_DELAY_3 + #define ST7920_DELAY_3 DELAY_NS(125) +#endif diff --git a/Marlin/src/pins/pins_MKS_ROBIN_MINI.h b/Marlin/src/pins/stm32/pins_MKS_ROBIN_MINI.h similarity index 81% rename from Marlin/src/pins/pins_MKS_ROBIN_MINI.h rename to Marlin/src/pins/stm32/pins_MKS_ROBIN_MINI.h index b488955b89..ab5e0cc531 100644 --- a/Marlin/src/pins/pins_MKS_ROBIN_MINI.h +++ b/Marlin/src/pins/stm32/pins_MKS_ROBIN_MINI.h @@ -27,9 +27,7 @@ #ifndef __STM32F1__ #error "Oops! Select an STM32F1 board in 'Tools > Board.'" -#endif - -#if HOTENDS > 1 || E_STEPPERS > 1 +#elif HOTENDS > 1 || E_STEPPERS > 1 #error "MKS Robin mini supports up to 1 hotends / E-steppers. Comment out this line to continue." #endif @@ -55,6 +53,10 @@ #define Z_MIN_PIN PA11 #define Z_MAX_PIN PC4 +#ifndef FIL_RUNOUT_PIN + #define FIL_RUNOUT_PIN PF11 // MT_DET +#endif + // // Steppers // @@ -78,44 +80,55 @@ // Temperature Sensors // #define TEMP_0_PIN PC1 // TH1 -//#define TEMP_1_PIN PC2 // TH2 #define TEMP_BED_PIN PC0 // TB1 // // Heaters / Fans // #define HEATER_0_PIN PC3 // HEATER1 -//#define HEATER_1_PIN PA6 // HEATER2 #define HEATER_BED_PIN PA0 // HOT BED #define FAN_PIN PB1 // FAN -#define BTN_ENC PB3 // Pin is not connected. Real pin is needed to enable encoder's push button functionality used by touch screen - +// +// Thermocouples +// //#define MAX6675_SS_PIN PE5 // TC1 - CS1 //#define MAX6675_SS_PIN PE6 // TC2 - CS2 +// +// Misc. Functions +// #define POWER_LOSS_PIN PA2 // PW_DET #define PS_ON_PIN PA3 // PW_OFF -#define FIL_RUNOUT_PIN PF11 // MT_DET -#define BEEPER_PIN PC5 //#define LED_PIN PB2 -/** - * Note: MKS Robin TFT screens may have different TFT controllers - * If the screen stays white, disable 'LCD_RESET_PIN' to rely on the bootloader to do screen initialization. - */ -#define LCD_RESET_PIN PF6 -#define NO_LCD_REINIT // Suppress LCD re-initialization - -#define LCD_BACKLIGHT_PIN PD13 -#define FSMC_CS_PIN PD7 // NE4 -#define FSMC_RS_PIN PD11 // A0 -#define TOUCH_CS PC2 - +// +// LCD / Controller +// +#define BEEPER_PIN PC5 #define SD_DETECT_PIN PD12 +/** + * Note: MKS Robin TFT screens use various TFT controllers. + * If the screen stays white, disable 'LCD_RESET_PIN' + * to let the bootloader init the screen. + */ +#if ENABLED(FSMC_GRAPHICAL_TFT) + #define LCD_RESET_PIN PF6 + #define NO_LCD_REINIT // Suppress LCD re-initialization + + #define LCD_BACKLIGHT_PIN PD13 + + #if ENABLED(TOUCH_BUTTONS) + #define BTN_ENC PB3 // Not connected. TODO: Replace this hack to enable button code + #define FSMC_CS_PIN PD7 // NE4 + #define FSMC_RS_PIN PD11 // A0 + #define TOUCH_CS_PIN PC2 + #endif +#endif + // Motor current PWM pins #define MOTOR_CURRENT_PWM_XY_PIN PA6 #define MOTOR_CURRENT_PWM_Z_PIN PA7 diff --git a/Marlin/src/pins/pins_MKS_ROBIN_NANO.h b/Marlin/src/pins/stm32/pins_MKS_ROBIN_NANO.h similarity index 77% rename from Marlin/src/pins/pins_MKS_ROBIN_NANO.h rename to Marlin/src/pins/stm32/pins_MKS_ROBIN_NANO.h index d57ac33406..406e12abc3 100644 --- a/Marlin/src/pins/pins_MKS_ROBIN_NANO.h +++ b/Marlin/src/pins/stm32/pins_MKS_ROBIN_NANO.h @@ -27,9 +27,7 @@ #ifndef __STM32F1__ #error "Oops! Select an STM32F1 board in 'Tools > Board.'" -#endif - -#if HOTENDS > 2 || E_STEPPERS > 2 +#elif HOTENDS > 2 || E_STEPPERS > 2 #error "MKS Robin nano supports up to 2 hotends / E-steppers. Comment out this line to continue." #endif @@ -53,6 +51,10 @@ #define Z_MIN_PIN PA11 #define Z_MAX_PIN PC4 +#ifndef FIL_RUNOUT_PIN + #define FIL_RUNOUT_PIN PA4 // MT_DET +#endif + // // Steppers // @@ -92,28 +94,41 @@ #define FAN_PIN PB1 // FAN -#define BTN_ENC PC13 // Pin is not connected. Real pin is needed to enable encoder's push button functionality used by touch screen - +// +// Thermocouples +// //#define MAX6675_SS_PIN PE5 // TC1 - CS1 //#define MAX6675_SS_PIN PE6 // TC2 - CS2 +// +// Misc. Functions +// #define POWER_LOSS_PIN PA2 // PW_DET #define PS_ON_PIN PA3 // PW_OFF -#define FIL_RUNOUT_PIN PA4 // MT_DET -#define BEEPER_PIN PC5 #define LED_PIN PB2 -/** - * Note: MKS Robin TFT screens may have different TFT controllers - * If the screen stays white, disable 'LCD_RESET_PIN' to rely on the bootloader to do screen initialization. - */ -#define LCD_RESET_PIN PF6 -#define NO_LCD_REINIT // Suppress LCD re-initialization - -#define LCD_BACKLIGHT_PIN PD13 -#define FSMC_CS_PIN PD7 // NE4 -#define FSMC_RS_PIN PD11 // A0 -#define TOUCH_CS PA7 - +// +// LCD / Controller +// +#define BEEPER_PIN PC5 #define SD_DETECT_PIN PD12 + +/** + * Note: MKS Robin TFT screens use various TFT controllers. + * If the screen stays white, disable 'LCD_RESET_PIN' + * to let the bootloader init the screen. + */ +#if ENABLED(FSMC_GRAPHICAL_TFT) + #define LCD_RESET_PIN PF6 + #define NO_LCD_REINIT // Suppress LCD re-initialization + + #define LCD_BACKLIGHT_PIN PD13 + + #if ENABLED(TOUCH_BUTTONS) + #define BTN_ENC PC13 // Not connected. TODO: Replace this hack to enable button code + #define FSMC_CS_PIN PD7 // NE4 + #define FSMC_RS_PIN PD11 // A0 + #define TOUCH_CS_PIN PA7 + #endif +#endif diff --git a/Marlin/src/pins/pins_MORPHEUS.h b/Marlin/src/pins/stm32/pins_MORPHEUS.h similarity index 100% rename from Marlin/src/pins/pins_MORPHEUS.h rename to Marlin/src/pins/stm32/pins_MORPHEUS.h diff --git a/Marlin/src/pins/pins_REMRAM_V1.h b/Marlin/src/pins/stm32/pins_REMRAM_V1.h similarity index 96% rename from Marlin/src/pins/pins_REMRAM_V1.h rename to Marlin/src/pins/stm32/pins_REMRAM_V1.h index 409d47b2c2..6e72bdc2ec 100644 --- a/Marlin/src/pins/pins_REMRAM_V1.h +++ b/Marlin/src/pins/stm32/pins_REMRAM_V1.h @@ -25,10 +25,10 @@ #error "Oops! Select an STM32F7 board in 'Tools > Board.'" #endif +#define BOARD_NAME "RemRam v1" #define DEFAULT_MACHINE_NAME "RemRam" -#define BOARD_NAME "RemRam v1" -#define EEPROM_EMULATED_WITH_SRAM // Emulate the EEPROM using Backup SRAM +#define SRAM_EEPROM_EMULATION // Emulate the EEPROM using Backup SRAM #if HOTENDS > 1 || E_STEPPERS > 1 #error "RemRam supports only one hotend / E-stepper." diff --git a/Marlin/src/pins/pins_RUMBA32.h b/Marlin/src/pins/stm32/pins_RUMBA32.h similarity index 95% rename from Marlin/src/pins/pins_RUMBA32.h rename to Marlin/src/pins/stm32/pins_RUMBA32.h index f3fb0a3d4a..5ac70744ff 100644 --- a/Marlin/src/pins/pins_RUMBA32.h +++ b/Marlin/src/pins/stm32/pins_RUMBA32.h @@ -23,19 +23,16 @@ #ifndef STM32F4 #error "Oops! Select an STM32F4 board in 'Tools > Board.'" +#elif HOTENDS > 3 || E_STEPPERS > 3 + #error "RUMBA32 supports up to 3 hotends / E-steppers." #endif #define RUMBA32_V1_0 -#define DEFAULT_MACHINE_NAME "RUMBA32" -#define BOARD_NAME "RUMBA32" +#define BOARD_NAME "RUMBA32" +#define DEFAULT_MACHINE_NAME BOARD_NAME //#define I2C_EEPROM - -#define E2END 0xFFF // EEPROM end address (4kB) - -#if HOTENDS > 3 || E_STEPPERS > 3 - #error "RUMBA32 supports up to 3 hotends / E-steppers." -#endif +#define E2END 0xFFF // 4KB // // Limit Switches diff --git a/Marlin/src/pins/pins_STEVAL.h b/Marlin/src/pins/stm32/pins_STEVAL.h similarity index 98% rename from Marlin/src/pins/pins_STEVAL.h rename to Marlin/src/pins/stm32/pins_STEVAL.h index d174b339c9..062981a1ea 100644 --- a/Marlin/src/pins/pins_STEVAL.h +++ b/Marlin/src/pins/stm32/pins_STEVAL.h @@ -35,9 +35,9 @@ // // Limit Switches // -#define X_MIN_PIN 38 // PD8 X_STOP +#define X_MIN_PIN 38 // PD8 X_STOP #define X_MAX_PIN -1 -#define Y_MIN_PIN 39 // PD9 Y_STOP +#define Y_MIN_PIN 39 // PD9 Y_STOP #define Y_MAX_PIN -1 #define Z_MIN_PIN 40 // PD10 Z_STOP #define Z_MAX_PIN -1 diff --git a/Marlin/src/pins/pins_STM32F1R.h b/Marlin/src/pins/stm32/pins_STM32F1R.h similarity index 96% rename from Marlin/src/pins/pins_STM32F1R.h rename to Marlin/src/pins/stm32/pins_STM32F1R.h index 91de11a959..7b3e910479 100644 --- a/Marlin/src/pins/pins_STM32F1R.h +++ b/Marlin/src/pins/stm32/pins_STM32F1R.h @@ -29,18 +29,15 @@ * 21017 Victor Perez Marlin for stm32f1 test */ +#define BOARD_NAME "Misc. STM32F1R" #define DEFAULT_MACHINE_NAME "STM32F103RET6" -#define BOARD_NAME "Marlin for STM32" -// Ignore temp readings during develpment. -#define BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE +// Ignore temp readings during development. +//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000 // // Limit Switches // -#define U_MIN_PIN -1 -#define V_MIN_PIN -1 -#define W_MIN_PIN -1 #define X_STOP_PIN PB3 #define Y_STOP_PIN PB4 #define Z_STOP_PIN PB5 @@ -233,7 +230,7 @@ // Beeper on AUX-4 #define BEEPER_PIN 33 - // buttons are directly attached using AUX-2 + // buttons are directly attached to AUX-2 #if ENABLED(REPRAPWORLD_KEYPAD) #define BTN_EN1 64 #define BTN_EN2 59 diff --git a/Marlin/src/pins/pins_STM32F4.h b/Marlin/src/pins/stm32/pins_STM32F4.h similarity index 95% rename from Marlin/src/pins/pins_STM32F4.h rename to Marlin/src/pins/stm32/pins_STM32F4.h index 7ce1d2d6c5..23c5b3c118 100644 --- a/Marlin/src/pins/pins_STM32F4.h +++ b/Marlin/src/pins/stm32/pins_STM32F4.h @@ -23,21 +23,19 @@ #if !defined(STM32F4) && !defined(STM32F4xx) #error "Oops! Select an STM32F4 board in 'Tools > Board.'" +#elif HOTENDS > 2 || E_STEPPERS > 2 + #error "STM32F4 supports up to 2 hotends / E-steppers." #endif +#define BOARD_NAME "Misc. STM32F4" #define DEFAULT_MACHINE_NAME "STM32F407VET6" -#define BOARD_NAME "STM32F4 Board" //#define I2C_EEPROM -#define E2END 0xFFF // EEPROM end address (4kB) +#define E2END 0xFFF // 4KB -// Ignore temp readings during develpment. -//#define BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE - -#if HOTENDS > 2 || E_STEPPERS > 2 - #error "STM32F4 supports up to 2 hotends / E-steppers." -#endif +// Ignore temp readings during development. +//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000 // // Limit Switches diff --git a/Marlin/src/pins/pins_STM3R_MINI.h b/Marlin/src/pins/stm32/pins_STM3R_MINI.h similarity index 55% rename from Marlin/src/pins/pins_STM3R_MINI.h rename to Marlin/src/pins/stm32/pins_STM3R_MINI.h index acf2dfaf29..5ababb36bf 100644 --- a/Marlin/src/pins/pins_STM3R_MINI.h +++ b/Marlin/src/pins/stm32/pins_STM3R_MINI.h @@ -29,21 +29,18 @@ * 21017 Victor Perez Marlin for stm32f1 test */ -#define DEFAULT_MACHINE_NAME "STM3R Mini" -#define BOARD_NAME "Marlin for STM32" +#define BOARD_NAME "STM3R Mini" +#define DEFAULT_MACHINE_NAME BOARD_NAME // Enable I2C_EEPROM for testing #define I2C_EEPROM -// Ignore temp readings during develpment. -#define BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE +// Ignore temp readings during development. +//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000 // // Limit Switches // -#define U_MIN_PIN -1 -#define V_MIN_PIN -1 -#define W_MIN_PIN -1 #define X_STOP_PIN PD0 #define Y_STOP_PIN PD1 #define Z_STOP_PIN PD4 @@ -118,35 +115,43 @@ #if HAS_SPI_LCD #if ENABLED(REPRAPWORLD_GRAPHICAL_LCD) - #define LCD_PINS_RS 49 // CS chip select /SS chip slave select - #define LCD_PINS_ENABLE 51 // SID (MOSI) - #define LCD_PINS_D4 52 // SCK (CLK) clock + #define LCD_PINS_RS 49 // CS chip select /SS chip slave select + #define LCD_PINS_ENABLE 51 // SID (MOSI) + #define LCD_PINS_D4 52 // SCK (CLK) clock #elif BOTH(NEWPANEL, PANEL_ONE) - #define LCD_PINS_RS PB8 - #define LCD_PINS_ENABLE PD2 - #define LCD_PINS_D4 PB12 - #define LCD_PINS_D5 PB13 - #define LCD_PINS_D6 PB14 - #define LCD_PINS_D7 PB15 + #define LCD_PINS_RS PB8 + #define LCD_PINS_ENABLE PD2 + #define LCD_PINS_D4 PB12 + #define LCD_PINS_D5 PB13 + #define LCD_PINS_D6 PB14 + #define LCD_PINS_D7 PB15 #else - #define LCD_PINS_RS PB8 - #define LCD_PINS_ENABLE PD2 - #define LCD_PINS_D4 PB12 - #define LCD_PINS_D5 PB13 - #define LCD_PINS_D6 PB14 - #define LCD_PINS_D7 PB15 + #define LCD_PINS_RS PB8 + #define LCD_PINS_ENABLE PD2 + #define LCD_PINS_D4 PB12 + #define LCD_PINS_D5 PB13 + #define LCD_PINS_D6 PB14 + #define LCD_PINS_D7 PB15 #if DISABLED(NEWPANEL) - #define BEEPER_PIN 33 + #define BEEPER_PIN 33 // Buttons are attached to a shift register // Not wired yet - //#define SHIFT_CLK 38 - //#define SHIFT_LD 42 - //#define SHIFT_OUT 40 - //#define SHIFT_EN 17 + //#define SHIFT_CLK 38 + //#define SHIFT_LD 42 + //#define SHIFT_OUT 40 + //#define SHIFT_EN 17 #endif #endif - #if ENABLED(NEWPANEL) + #if ENABLED(TOUCH_BUTTONS) + + #define TOUCH_CS_PIN PB12 // SPI2_NSS + #define TOUCH_SCK_PIN PB13 + #define TOUCH_MOSI_PIN PB14 + #define TOUCH_MISO_PIN PB15 + #define TOUCH_INT_PIN PC6 // (PenIRQ coming from ADS7843) + + #elif ENABLED(NEWPANEL) #if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) @@ -165,111 +170,111 @@ #elif ENABLED(REPRAPWORLD_GRAPHICAL_LCD) - #define BTN_EN1 64 - #define BTN_EN2 59 - #define BTN_ENC 63 - #define SD_DETECT_PIN 42 + #define BTN_EN1 64 + #define BTN_EN2 59 + #define BTN_ENC 63 + #define SD_DETECT_PIN 42 #elif ENABLED(LCD_I2C_PANELOLU2) - #define BTN_EN1 47 - #define BTN_EN2 43 - #define BTN_ENC 32 - #define LCD_SDSS 53 - #define SD_DETECT_PIN -1 - #define KILL_PIN 41 + #define BTN_EN1 47 + #define BTN_EN2 43 + #define BTN_ENC 32 + #define LCD_SDSS 53 + #define SD_DETECT_PIN -1 + #define KILL_PIN 41 #elif ENABLED(LCD_I2C_VIKI) - #define BTN_EN1 22 // http://files.panucatt.com/datasheets/viki_wiring_diagram.pdf explains 40/42. - #define BTN_EN2 7 // 22/7 are unused on RAMPS_14. 22 is unused and 7 the SERVO0_PIN on RAMPS_13. + #define BTN_EN1 22 // http://files.panucatt.com/datasheets/viki_wiring_diagram.pdf explains 40/42. + #define BTN_EN2 7 // 22/7 are unused on RAMPS_14. 22 is unused and 7 the SERVO0_PIN on RAMPS_13. - #define BTN_ENC -1 - #define LCD_SDSS 53 - #define SD_DETECT_PIN 49 + #define BTN_ENC -1 + #define LCD_SDSS 53 + #define SD_DETECT_PIN 49 #elif ANY(VIKI2, miniVIKI) - #define BEEPER_PIN 33 + #define BEEPER_PIN 33 // Pins for DOGM SPI LCD Support - #define DOGLCD_A0 44 - #define DOGLCD_CS 45 + #define DOGLCD_A0 44 + #define DOGLCD_CS 45 #define LCD_SCREEN_ROT_180 - #define BTN_EN1 22 - #define BTN_EN2 7 - #define BTN_ENC 39 + #define BTN_EN1 22 + #define BTN_EN2 7 + #define BTN_ENC 39 - #define SDSS 53 - #define SD_DETECT_PIN -1 // Pin 49 for display sd interface, 72 for easy adapter board + #define SDSS 53 + #define SD_DETECT_PIN -1 // Pin 49 for display sd interface, 72 for easy adapter board - #define KILL_PIN 31 + #define KILL_PIN 31 #define STAT_LED_RED_PIN 32 #define STAT_LED_BLUE_PIN 35 #elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER) - #define BTN_EN1 35 - #define BTN_EN2 37 - #define BTN_ENC 31 - #define SD_DETECT_PIN 49 - #define LCD_SDSS 53 - #define KILL_PIN 41 - #define BEEPER_PIN 23 - #define DOGLCD_CS 29 - #define DOGLCD_A0 27 + #define BTN_EN1 35 + #define BTN_EN2 37 + #define BTN_ENC 31 + #define SD_DETECT_PIN 49 + #define LCD_SDSS 53 + #define KILL_PIN 41 + #define BEEPER_PIN 23 + #define DOGLCD_CS 29 + #define DOGLCD_A0 27 #define LCD_BACKLIGHT_PIN 33 #elif ENABLED(MINIPANEL) - #define BEEPER_PIN 42 + #define BEEPER_PIN 42 // Pins for DOGM SPI LCD Support - #define DOGLCD_A0 44 - #define DOGLCD_CS 66 + #define DOGLCD_A0 44 + #define DOGLCD_CS 66 #define LCD_BACKLIGHT_PIN 65 // backlight LED on A11/D65 - #define SDSS 53 + #define SDSS 53 - #define KILL_PIN 64 + #define KILL_PIN 64 // GLCD features // Uncomment screen orientation //#define LCD_SCREEN_ROT_90 //#define LCD_SCREEN_ROT_180 //#define LCD_SCREEN_ROT_270 // The encoder and click button - #define BTN_EN1 40 - #define BTN_EN2 63 - #define BTN_ENC 59 + #define BTN_EN1 40 + #define BTN_EN2 63 + #define BTN_ENC 59 // not connected to a pin - #define SD_DETECT_PIN 49 + #define SD_DETECT_PIN 49 #else // Beeper on AUX-4 - #define BEEPER_PIN 33 + #define BEEPER_PIN 33 - // buttons are directly attached using AUX-2 + // buttons are directly attached to AUX-2 #if ENABLED(REPRAPWORLD_KEYPAD) - #define BTN_EN1 64 - #define BTN_EN2 59 - #define BTN_ENC 63 - #define SHIFT_OUT 40 - #define SHIFT_CLK 44 - #define SHIFT_LD 42 + #define BTN_EN1 64 + #define BTN_EN2 59 + #define BTN_ENC 63 + #define SHIFT_OUT 40 + #define SHIFT_CLK 44 + #define SHIFT_LD 42 #elif ENABLED(PANEL_ONE) - #define BTN_EN1 59 // AUX2 PIN 3 - #define BTN_EN2 63 // AUX2 PIN 4 - #define BTN_ENC 49 // AUX3 PIN 7 + #define BTN_EN1 59 // AUX2 PIN 3 + #define BTN_EN2 63 // AUX2 PIN 4 + #define BTN_ENC 49 // AUX3 PIN 7 #else - #define BTN_EN1 37 - #define BTN_EN2 35 - #define BTN_ENC 31 + #define BTN_EN1 37 + #define BTN_EN2 35 + #define BTN_ENC 31 #endif #if ENABLED(G3D_PANEL) - #define SD_DETECT_PIN 49 - #define KILL_PIN 41 + #define SD_DETECT_PIN 49 + #define KILL_PIN 41 #else //#define SD_DETECT_PIN -1 // Ramps doesn't use this #endif diff --git a/Marlin/src/pins/pins_THE_BORG.h b/Marlin/src/pins/stm32/pins_THE_BORG.h similarity index 95% rename from Marlin/src/pins/pins_THE_BORG.h rename to Marlin/src/pins/stm32/pins_THE_BORG.h index 141320f88c..8069076e5e 100644 --- a/Marlin/src/pins/pins_THE_BORG.h +++ b/Marlin/src/pins/stm32/pins_THE_BORG.h @@ -21,21 +21,19 @@ */ #pragma once -#if !defined(STM32F7) +#ifndef STM32F7 #error "Oops! Select an STM32F7 board in 'Tools > Board.'" +#elif HOTENDS > 3 || E_STEPPERS > 3 + #error "The-Borg supports up to 3 hotends / E-steppers." #endif -#define DEFAULT_MACHINE_NAME "The-Borge" -#define BOARD_NAME "The-Borge" +#define BOARD_NAME "The-Borge" +#define DEFAULT_MACHINE_NAME BOARD_NAME #define E2END 0xFFF // EEPROM end address -// Ignore temp readings during develpment. -#define BOGUS_TEMPERATURE_FAILSAFE_OVERRIDE - -#if HOTENDS > 3 || E_STEPPERS > 3 - #error "The-Borg supports up to 3 hotends / E-steppers." -#endif +// Ignore temp readings during development. +//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000 // // Limit Switches diff --git a/Marlin/src/pins/pins_5DPRINT.h b/Marlin/src/pins/teensy2/pins_5DPRINT.h similarity index 100% rename from Marlin/src/pins/pins_5DPRINT.h rename to Marlin/src/pins/teensy2/pins_5DPRINT.h diff --git a/Marlin/src/pins/pins_BRAINWAVE.h b/Marlin/src/pins/teensy2/pins_BRAINWAVE.h similarity index 100% rename from Marlin/src/pins/pins_BRAINWAVE.h rename to Marlin/src/pins/teensy2/pins_BRAINWAVE.h diff --git a/Marlin/src/pins/pins_BRAINWAVE_PRO.h b/Marlin/src/pins/teensy2/pins_BRAINWAVE_PRO.h similarity index 100% rename from Marlin/src/pins/pins_BRAINWAVE_PRO.h rename to Marlin/src/pins/teensy2/pins_BRAINWAVE_PRO.h diff --git a/Marlin/src/pins/pins_PRINTRBOARD.h b/Marlin/src/pins/teensy2/pins_PRINTRBOARD.h similarity index 100% rename from Marlin/src/pins/pins_PRINTRBOARD.h rename to Marlin/src/pins/teensy2/pins_PRINTRBOARD.h diff --git a/Marlin/src/pins/pins_PRINTRBOARD_REVF.h b/Marlin/src/pins/teensy2/pins_PRINTRBOARD_REVF.h similarity index 100% rename from Marlin/src/pins/pins_PRINTRBOARD_REVF.h rename to Marlin/src/pins/teensy2/pins_PRINTRBOARD_REVF.h diff --git a/Marlin/src/pins/pins_SAV_MKI.h b/Marlin/src/pins/teensy2/pins_SAV_MKI.h similarity index 97% rename from Marlin/src/pins/pins_SAV_MKI.h rename to Marlin/src/pins/teensy2/pins_SAV_MKI.h index 82d7630311..17928cd139 100644 --- a/Marlin/src/pins/pins_SAV_MKI.h +++ b/Marlin/src/pins/teensy2/pins_SAV_MKI.h @@ -66,9 +66,9 @@ #error "Oops! Select 'Teensy++ 2.0' or 'Printrboard' in 'Tools > Board.'" #endif -#define DEFAULT_MACHINE_NAME "SAV MkI" -#define DEFAULT_SOURCE_CODE_URL "https://github.com/fmalpartida/Marlin/tree/SAV-MkI-config" #define BOARD_NAME "SAV MkI" +#define DEFAULT_MACHINE_NAME BOARD_NAME +#define DEFAULT_SOURCE_CODE_URL "https://tinyurl.com/onru38b" // // Servos diff --git a/Marlin/src/pins/pins_TEENSY2.h b/Marlin/src/pins/teensy2/pins_TEENSY2.h similarity index 100% rename from Marlin/src/pins/pins_TEENSY2.h rename to Marlin/src/pins/teensy2/pins_TEENSY2.h diff --git a/Marlin/src/pins/pins_TEENSYLU.h b/Marlin/src/pins/teensy2/pins_TEENSYLU.h similarity index 100% rename from Marlin/src/pins/pins_TEENSYLU.h rename to Marlin/src/pins/teensy2/pins_TEENSYLU.h diff --git a/Marlin/src/pins/pins_TEENSY31_32.h b/Marlin/src/pins/teensy3/pins_TEENSY31_32.h similarity index 52% rename from Marlin/src/pins/pins_TEENSY31_32.h rename to Marlin/src/pins/teensy3/pins_TEENSY31_32.h index 7036525762..7eb57bc088 100644 --- a/Marlin/src/pins/pins_TEENSY31_32.h +++ b/Marlin/src/pins/teensy3/pins_TEENSY31_32.h @@ -21,17 +21,17 @@ */ #pragma once -/**************************************************************************************** -* Teensy 3.1 (MK20DX256) and Teensy 3.2 (MK20DX256) Breadboard pin assignments -* Requires the Teensyduino software with Teensy 3.1 or Teensy 3.2 selected in Arduino IDE! -* http://www.pjrc.com/teensy/teensyduino.html -****************************************************************************************/ +/** + * Teensy 3.1 (MK20DX256) and Teensy 3.2 (MK20DX256) Breadboard pin assignments + * Requires the Teensyduino software with Teensy 3.1 or Teensy 3.2 selected in Arduino IDE! + * http://www.pjrc.com/teensy/teensyduino.html + */ #if !IS_32BIT_TEENSY #error "Oops! Select 'Teensy 3.1' or 'Teensy 3.2' in 'Tools > Board.'" #endif -#if IS_TEENSY32 +#ifndef BOARD_NAME #define BOARD_NAME "Teensy3.2" #endif @@ -41,64 +41,73 @@ // // Limit Switches // -#define X_STOP_PIN 3 -#define Y_STOP_PIN 4 -#define Z_STOP_PIN 5 +#define X_STOP_PIN 3 +#define Y_STOP_PIN 4 +#define Z_STOP_PIN 5 // // Steppers // -#define X_STEP_PIN 5 -#define X_DIR_PIN 6 -#define X_ENABLE_PIN 2 +#define X_STEP_PIN 5 +#define X_DIR_PIN 6 +#define X_ENABLE_PIN 2 -#define Y_STEP_PIN 7 -#define Y_DIR_PIN 8 -#define Y_ENABLE_PIN 2 +#define Y_STEP_PIN 7 +#define Y_DIR_PIN 8 +#define Y_ENABLE_PIN 2 -#define Z_STEP_PIN 9 +#define Z_STEP_PIN 9 #define Z_DIR_PIN 10 -#define Z_ENABLE_PIN 2 +#define Z_ENABLE_PIN 2 #define E0_STEP_PIN 11 #define E0_DIR_PIN 12 -#define E0_ENABLE_PIN 2 +#define E0_ENABLE_PIN 2 -// #define E1_STEP_PIN 33 -// #define E1_DIR_PIN 34 -// #define E1_ENABLE_PIN 35 +//#define E1_STEP_PIN 33 +//#define E1_DIR_PIN 34 +//#define E1_ENABLE_PIN 35 +// +// Heaters / Fans +// #define HEATER_0_PIN 20 -// #define HEATER_1_PIN 36 +// #define HEATER_1_PIN 36 #define HEATER_BED_PIN 21 #ifndef FAN_PIN #define FAN_PIN 22 #endif -#define TEMP_0_PIN 14 // Extruder / Analog pin numbering: 2 => A2 -// #define TEMP_1_PIN 0 -#define TEMP_BED_PIN 15 // Bed / Analog pin numbering +// +// Temperature Sensors +// +#define TEMP_0_PIN 14 // Analog Input - Extruder 2 => A2 +//#define TEMP_1_PIN 0 // Analog Input +#define TEMP_BED_PIN 15 // Analog Input - Bed -// #define SDSS 16 // 8 +#ifndef FILWIDTH_PIN + #define FILWIDTH_PIN 6 // Analog Input +#endif + +// +// Misc. Functions +// + +//#define SDSS 16 // 8 #define LED_PIN 13 -#define PS_ON_PIN -1 -#define ALARM_PIN -1 -// #define FILWIDTH_PIN 6 -// #define SOL1_PIN 28 +//#define SOL1_PIN 28 + +// +// LCD / Controller +// + +//#define SCK_PIN 13 +//#define MISO_PIN 12 +//#define MOSI_PIN 11 -#if 0 -// Pretty sure this is obsolete! -// Please use Marlin 1.1.x pins files as reference for new pins files. -#ifndef SDSUPPORT - // these are defined in the SD library if building with SD support - #define SCK_PIN 13 - #define MISO_PIN 12 - #define MOSI_PIN 11 -#endif -#endif /* -#ifdef ULTRA_LCD +#if HAS_SPI_LCD #define LCD_PINS_RS 40 #define LCD_PINS_ENABLE 41 #define LCD_PINS_D4 42 diff --git a/Marlin/src/pins/pins_TEENSY35_36.h b/Marlin/src/pins/teensy3/pins_TEENSY35_36.h similarity index 100% rename from Marlin/src/pins/pins_TEENSY35_36.h rename to Marlin/src/pins/teensy3/pins_TEENSY35_36.h diff --git a/Marlin/src/sd/Sd2Card.cpp b/Marlin/src/sd/Sd2Card.cpp index 433db3ff85..a6223858cb 100644 --- a/Marlin/src/sd/Sd2Card.cpp +++ b/Marlin/src/sd/Sd2Card.cpp @@ -30,7 +30,7 @@ #include "../inc/MarlinConfig.h" -#if ENABLED(SDSUPPORT) && DISABLED(USB_FLASH_DRIVE_SUPPORT, SDIO_SUPPORT) +#if ENABLED(SDSUPPORT) && NONE(USB_FLASH_DRIVE_SUPPORT, SDIO_SUPPORT) /* Enable FAST CRC computations - You can trade speed for FLASH space if * needed by disabling the following define */ @@ -227,7 +227,7 @@ bool Sd2Card::eraseSingleBlockEnable() { * \return true for success, false for failure. * The reason for failure can be determined by calling errorCode() and errorData(). */ -bool Sd2Card::init(const uint8_t sckRateID/*=0*/, const pin_t chipSelectPin/*=SD_CHIP_SELECT_PIN*/) { +bool Sd2Card::init(const uint8_t sckRateID, const pin_t chipSelectPin) { errorCode_ = type_ = 0; chipSelectPin_ = chipSelectPin; // 16-bit init start time allows over a minute diff --git a/Marlin/src/sd/Sd2Card.h b/Marlin/src/sd/Sd2Card.h index cc895b0092..f44dbb3124 100644 --- a/Marlin/src/sd/Sd2Card.h +++ b/Marlin/src/sd/Sd2Card.h @@ -85,10 +85,6 @@ uint8_t const SD_CARD_TYPE_SD1 = 1, // Standard capacity V1 #elif USE_SOFTWARE_SPI #define SOFTWARE_SPI #endif // MEGA_SOFT_SPI -//------------------------------------------------------------------------------ -// SPI pin definitions - do not edit here - change in SdFatConfig.h -// -#define SD_CHIP_SELECT_PIN SS_PIN /** * \class Sd2Card @@ -123,7 +119,7 @@ public: * * \return true for success or false for failure. */ - bool init(const uint8_t sckRateID=SPI_FULL_SPEED, const pin_t chipSelectPin=SD_CHIP_SELECT_PIN); + bool init(const uint8_t sckRateID, const pin_t chipSelectPin); bool readBlock(uint32_t block, uint8_t* dst); diff --git a/Marlin/src/sd/SdVolume.h b/Marlin/src/sd/SdVolume.h index 1c72fd3d27..b5282bdce3 100644 --- a/Marlin/src/sd/SdVolume.h +++ b/Marlin/src/sd/SdVolume.h @@ -33,6 +33,10 @@ * This file is part of the Arduino Sd2Card Library */ +#include + +#include "../inc/MarlinConfigPre.h" + #if ENABLED(USB_FLASH_DRIVE_SUPPORT) #include "usb_flashdrive/Sd2Card_FlashDrive.h" #elif ENABLED(SDIO_SUPPORT) @@ -43,7 +47,6 @@ #include "SdFatConfig.h" #include "SdFatStructs.h" -#include //============================================================================== // SdVolume class diff --git a/Marlin/src/sd/cardreader.cpp b/Marlin/src/sd/cardreader.cpp index efd955259d..76fe43d09b 100644 --- a/Marlin/src/sd/cardreader.cpp +++ b/Marlin/src/sd/cardreader.cpp @@ -133,9 +133,8 @@ CardReader::CardReader() { // Disable autostart until card is initialized autostart_index = -1; - //power to SD reader - #if SDPOWER > -1 - OUT_WRITE(SDPOWER, HIGH); + #if PIN_EXISTS(SDPOWER) + OUT_WRITE(SDPOWER_PIN, HIGH); // Power the SD reader #endif } @@ -353,8 +352,8 @@ void CardReader::initsd() { else { flag.detected = true; SERIAL_ECHO_MSG(MSG_SD_CARD_OK); - #if ENABLED(EEPROM_SETTINGS) && DISABLED(FLASH_EEPROM_EMULATION) - (void)settings.load(); + #if ENABLED(EEPROM_SETTINGS) && NONE(FLASH_EEPROM_EMULATION, SPI_EEPROM, I2C_EEPROM) + settings.first_load(); #endif } setroot(); @@ -560,10 +559,8 @@ void CardReader::checkautostart() { if (autostart_index < 0 || flag.sdprinting) return; if (!isDetected()) initsd(); - - #if ENABLED(EEPROM_SETTINGS) && DISABLED(FLASH_EEPROM_EMULATION) - SERIAL_ECHOLNPGM("Loading settings from SD"); - (void)settings.load(); + #if ENABLED(EEPROM_SETTINGS) && NONE(FLASH_EEPROM_EMULATION, SPI_EEPROM, I2C_EEPROM) + else settings.first_load(); #endif if (isDetected() @@ -1010,18 +1007,16 @@ void CardReader::printingHasFinished() { #endif print_job_timer.stop(); - if (print_job_timer.duration() > 60) queue.inject_P(PSTR("M31")); + queue.enqueue_now_P(print_job_timer.duration() > 60 ? PSTR("M31") : PSTR("M117")); #if ENABLED(SDCARD_SORT_ALPHA) presort(); #endif - #if EITHER(ULTRA_LCD, EXTENSIBLE_UI) && ENABLED(LCD_SET_PROGRESS_MANUALLY) - ui.progress_bar_percent = 0; + #if ENABLED(LCD_SET_PROGRESS_MANUALLY) + ui.set_progress_done(); #endif - ui.reset_status(); - #if ENABLED(SD_REPRINT_LAST_SELECTED_FILE) ui.reselect_last_file(); #endif @@ -1047,10 +1042,8 @@ void CardReader::printingHasFinished() { #if ENABLED(POWER_LOSS_RECOVERY) - constexpr char job_recovery_file_name[5] = "/PLR"; - bool CardReader::jobRecoverFileExists() { - const bool exists = recovery.file.open(&root, job_recovery_file_name, O_READ); + const bool exists = recovery.file.open(&root, recovery.filename, O_READ); if (exists) recovery.file.close(); return exists; } @@ -1058,10 +1051,10 @@ void CardReader::printingHasFinished() { void CardReader::openJobRecoveryFile(const bool read) { if (!isDetected()) return; if (recovery.file.isOpen()) return; - if (!recovery.file.open(&root, job_recovery_file_name, read ? O_READ : O_CREAT | O_WRITE | O_TRUNC | O_SYNC)) - SERIAL_ECHOLNPAIR(MSG_SD_OPEN_FILE_FAIL, job_recovery_file_name, "."); + if (!recovery.file.open(&root, recovery.filename, read ? O_READ : O_CREAT | O_WRITE | O_TRUNC | O_SYNC)) + SERIAL_ECHOLNPAIR(MSG_SD_OPEN_FILE_FAIL, recovery.filename, "."); else if (!read) - SERIAL_ECHOLNPAIR(MSG_SD_WRITE_TO_FILE, job_recovery_file_name); + SERIAL_ECHOLNPAIR(MSG_SD_WRITE_TO_FILE, recovery.filename); } // Removing the job recovery file currently requires closing @@ -1070,7 +1063,7 @@ void CardReader::printingHasFinished() { void CardReader::removeJobRecoveryFile() { if (jobRecoverFileExists()) { recovery.init(); - removeFile(job_recovery_file_name); + removeFile(recovery.filename); #if ENABLED(DEBUG_POWER_LOSS_RECOVERY) SERIAL_ECHOPGM("Power-loss file delete"); serialprintPGM(jobRecoverFileExists() ? PSTR(" failed.\n") : PSTR("d.\n")); diff --git a/Marlin/src/sd/usb_flashdrive/Sd2Card_FlashDrive.cpp b/Marlin/src/sd/usb_flashdrive/Sd2Card_FlashDrive.cpp index 8de27cb319..d63a2b9f0f 100644 --- a/Marlin/src/sd/usb_flashdrive/Sd2Card_FlashDrive.cpp +++ b/Marlin/src/sd/usb_flashdrive/Sd2Card_FlashDrive.cpp @@ -1,9 +1,9 @@ /** * Marlin 3D Printer Firmware - * Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. - * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -31,7 +31,7 @@ #include "Sd2Card_FlashDrive.h" -#if EITHER(ULTRA_LCD, EXTENSIBLE_UI) +#if HAS_DISPLAY #include "../../lcd/ultralcd.h" #endif @@ -63,7 +63,7 @@ void Sd2Card::idle() { SERIAL_ECHOPGM("Starting USB host..."); if (!usb.start()) { SERIAL_ECHOPGM(" Failed. Retrying in 2s."); - #if EITHER(ULTRA_LCD, EXTENSIBLE_UI) + #if HAS_DISPLAY LCD_MESSAGEPGM("USB start failed"); #endif state = USB_HOST_DELAY_INIT; diff --git a/Marlin/src/sd/usb_flashdrive/Sd2Card_FlashDrive.h b/Marlin/src/sd/usb_flashdrive/Sd2Card_FlashDrive.h index 6325de15e6..eafb85c3ad 100644 --- a/Marlin/src/sd/usb_flashdrive/Sd2Card_FlashDrive.h +++ b/Marlin/src/sd/usb_flashdrive/Sd2Card_FlashDrive.h @@ -1,9 +1,9 @@ /** * Marlin 3D Printer Firmware - * Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. - * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by diff --git a/config/default/Configuration.h b/config/default/Configuration.h index f0a826ac6d..676d8bce6d 100644 --- a/config/default/Configuration.h +++ b/config/default/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_RAMPS_14_EFB #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu //#define CUSTOM_MACHINE_NAME "3D Printer" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1523,8 +1529,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1681,6 +1690,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1908,31 +1925,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1966,15 +1964,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1987,6 +1976,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2012,17 +2043,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2118,8 +2156,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/default/Configuration_adv.h b/config/default/Configuration_adv.h index 5a0677f409..634ebffdba 100644 --- a/config/default/Configuration_adv.h +++ b/config/default/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/3DFabXYZ/Migbot/Configuration.h b/config/examples/3DFabXYZ/Migbot/Configuration.h index e89fce346c..a200ec034f 100644 --- a/config/examples/3DFabXYZ/Migbot/Configuration.h +++ b/config/examples/3DFabXYZ/Migbot/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_MKS_BASE_14 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "3DFabXYZ i3" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -519,7 +525,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1554,8 +1560,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1712,6 +1721,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1939,31 +1956,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1997,15 +1995,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -2018,6 +2007,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2043,17 +2074,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2149,8 +2187,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h index d91dc27060..49eeac5c25 100644 --- a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h +++ b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu #define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2436,6 +2447,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/AlephObjects/TAZ4/Configuration.h b/config/examples/AlephObjects/TAZ4/Configuration.h index 67d81e9822..8744f26b13 100644 --- a/config/examples/AlephObjects/TAZ4/Configuration.h +++ b/config/examples/AlephObjects/TAZ4/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_RAMBO #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "TAZ" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 7 #define TEMP_SENSOR_1 0 @@ -523,7 +529,7 @@ #define MAX_BED_POWER 206 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //24V 360W silicone heater from NPH on 3mm borosilicate (TAZ 2.2+) @@ -1543,8 +1549,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1701,6 +1710,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1928,31 +1945,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1986,15 +1984,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -2007,6 +1996,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2032,17 +2063,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2138,8 +2176,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/AlephObjects/TAZ4/Configuration_adv.h b/config/examples/AlephObjects/TAZ4/Configuration_adv.h index 4853f9c753..032d5a7555 100644 --- a/config/examples/AlephObjects/TAZ4/Configuration_adv.h +++ b/config/examples/AlephObjects/TAZ4/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Alfawise/U20/Configuration.h b/config/examples/Alfawise/U20/Configuration.h new file mode 100644 index 0000000000..c5b2fc02fb --- /dev/null +++ b/config/examples/Alfawise/U20/Configuration.h @@ -0,0 +1,2314 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Configuration.h + * + * Basic settings such as: + * + * - Type of electronics + * - Type of temperature sensor + * - Printer geometry + * - Endstop configuration + * - LCD controller + * - Extra features + * + * Advanced settings can be found in Configuration_adv.h + * + */ +#define CONFIGURATION_H_VERSION 020000 + +//=========================================================================== +//============================= Getting Started ============================= +//=========================================================================== + +/** + * Here are some standard links for getting your machine calibrated: + * + * http://reprap.org/wiki/Calibration + * http://youtu.be/wAL9d7FgInk + * http://calculator.josefprusa.cz + * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide + * http://www.thingiverse.com/thing:5573 + * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap + * http://www.thingiverse.com/thing:298812 + */ + +//=========================================================================== +//============================= DELTA Printer =============================== +//=========================================================================== +// For a Delta printer start with one of the configuration files in the +// config/examples/delta directory and customize for your machine. +// + +//=========================================================================== +//============================= SCARA Printer =============================== +//=========================================================================== +// For a SCARA printer start with the configuration files in +// config/examples/SCARA and customize for your machine. +// + +//=========================================================================== +//============================= Alfawise Printer ============================ +//=========================================================================== + +// Forum link to help with a tutorial, in French! : +// https://www.lesimprimantes3d.fr/forum/topic/18260-alfawise-u20x-u30-marlin-2x-firmware-alternatif/ +// +// 1 - Select your Alfawise U30 or U20 or U20+ printer (NO MORE REQUIRED HERE), +// These defines are set in platformio.ini build parameters, sample for U20 -DU20 -DTS_V12 +// U20_PLUS is not tested, as we do not have a printer to test. +// Print bed PID settings MUST be tuned + +//#define U20_PLUS +//#define U20 +//#define U30 + +// 2 - Select the screen controller type. Most common is ILI9341 - First option. If your screen remains white, +// Try the alternate setting - this should enable ST7789V or ILI9328. For other LCDs... code is needed +// with the proper boot sequence to be developped. + +#define LCD_READ_ID 0xD3 // Read display identification information in reg ID4 0xD3, for ILI9341 screens +//#define LCD_READ_ID 0x04 // Read display identification information in reg ID1 0x04 - ST7789V / ILI9328 or others + +// 3 - Select the touch panel version, either 1.1 or 1.2. Most recent touch panel in France are V 1.2. Blue PCB +// V1.1 panels seem to be older, and came with green PCB. This selection only influence the calibration data +// Should calibration need to be redone, please follow the French Tutorial! (NO MORE REQUIRED HERE) + +//#define TS_V11 +//#define TS_V12 + +// 4 - If you want to tune the UI colors, define custom ones here. RGB 16 bits 5-6-5 format +// see https://ee-programming-notepad.blogspot.com/2016/10/16-bit-color-generator-picker.html + +//#define TFT_MARLINUI_COLOR 0xFFFF // White +//#define TFT_MARLINBG_COLOR 0x0000 // Black +//#define TFT_TOPICONS_COLOR 0x21DD // Blue +//#define TFT_DISABLED_COLOR 0x0003 // Almost black +//#define TFT_BTSLEFT_COLOR 0xDEE6 // 11011 110111 00110 Yellow +//#define TFT_BTRIGHT_COLOR 0x145F // 00010 100010 11111 Cyan + +//=========================================================================== +//============================= @section info =============================== +//=========================================================================== + + +// User-specified version info of this build to display in [Pronterface, etc] terminal window during +// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this +// build by the user have been successfully uploaded into firmware. +#define STRING_CONFIG_H_AUTHOR "Hobi, tpruvot" // Who made the changes. +#define SHOW_BOOTSCREEN +#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1 +#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2 + +/** + * *** VENDORS PLEASE READ *** + * + * Marlin allows you to add a custom boot image for Graphical LCDs. + * With this option Marlin will first show your custom screen followed + * by the standard Marlin logo with version number and web URL. + * + * We encourage you to take advantage of this new feature and we also + * respectfully request that you retain the unmodified Marlin boot screen. + */ + +// Enable to show the bitmap in Marlin/_Bootscreen.h on startup. +//#define SHOW_CUSTOM_BOOTSCREEN + +// Enable to show the bitmap in Marlin/_Statusscreen.h on the status screen. +#define CUSTOM_STATUS_SCREEN_IMAGE + +// @section machine + +/** + * Select the serial port on the board to use for communication with the host. + * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. + * + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] + */ +#define SERIAL_PORT 1 + +/** + * Select a secondary serial port on the board to use for communication with the host. + * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. + * + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] + */ +#define SERIAL_PORT_2 2 +#define NUM_SERIAL 2 + +/** + * This setting determines the communication speed of the printer. + * + * 250000 works in most cases, but you might try a lower speed if + * you commonly experience drop-outs during host printing. + * You may try up to 1000000 to speed up SD file transfer. + * + * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000] + */ +#define BAUDRATE 250000 + +// Enable the Bluetooth serial interface on AT90USB devices +//#define BLUETOOTH + +// Choose the name from boards.h that matches your setup +#ifndef MOTHERBOARD + #define MOTHERBOARD BOARD_LONGER3D_LK +#endif + +// Name displayed in the LCD "Ready" message and Info menu +//#define CUSTOM_MACHINE_NAME "3D Printer" +#ifdef U20 +#define CUSTOM_MACHINE_NAME "Alfawise U20" +#elif defined(U30) +#define CUSTOM_MACHINE_NAME "Alfawise U30" +#elif defined(U20_PLUS) +#define CUSTOM_MACHINE_NAME "Alfawise U20+" +#endif + +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 +//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" + +// @section extruder + +// This defines the number of extruders +// :[1, 2, 3, 4, 5, 6] +#define EXTRUDERS 1 + +// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc. +#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 + +// For Cyclops or any "multi-extruder" that shares a single nozzle. +//#define SINGLENOZZLE + +/** + * Průša MK2 Single Nozzle Multi-Material Multiplexer, and variants. + * + * This device allows one stepper driver on a control board to drive + * two to eight stepper motors, one at a time, in a manner suitable + * for extruders. + * + * This option only allows the multiplexer to switch on tool-change. + * Additional options to configure custom E moves are pending. + */ +//#define MK2_MULTIPLEXER +#if ENABLED(MK2_MULTIPLEXER) + // Override the default DIO selector pins here, if needed. + // Some pins files may provide defaults for these pins. + //#define E_MUX0_PIN 40 // Always Required + //#define E_MUX1_PIN 42 // Needed for 3 to 8 inputs + //#define E_MUX2_PIN 44 // Needed for 5 to 8 inputs +#endif + +/** + * Prusa Multi-Material Unit v2 + * + * Requires NOZZLE_PARK_FEATURE to park print head in case MMU unit fails. + * Requires EXTRUDERS = 5 + * + * For additional configuration see Configuration_adv.h + */ +//#define PRUSA_MMU2 + +// A dual extruder that uses a single stepper motor +//#define SWITCHING_EXTRUDER +#if ENABLED(SWITCHING_EXTRUDER) + #define SWITCHING_EXTRUDER_SERVO_NR 0 + #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3] + #if EXTRUDERS > 3 + #define SWITCHING_EXTRUDER_E23_SERVO_NR 1 + #endif +#endif + +// A dual-nozzle that uses a servomotor to raise/lower one (or both) of the nozzles +//#define SWITCHING_NOZZLE +#if ENABLED(SWITCHING_NOZZLE) + #define SWITCHING_NOZZLE_SERVO_NR 0 + //#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second + #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo) +#endif + +/** + * Two separate X-carriages with extruders that connect to a moving part + * via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN. + */ +//#define PARKING_EXTRUDER + +/** + * Two separate X-carriages with extruders that connect to a moving part + * via a magnetic docking mechanism using movements and no solenoid + * + * project : https://www.thingiverse.com/thing:3080893 + * movements : https://youtu.be/0xCEiG9VS3k + * https://youtu.be/Bqbcs0CU2FE + */ +//#define MAGNETIC_PARKING_EXTRUDER + +#if EITHER(PARKING_EXTRUDER, MAGNETIC_PARKING_EXTRUDER) + + #define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders + #define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder + //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381 + + #if ENABLED(PARKING_EXTRUDER) + + #define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage + #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil + #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined. + //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381 + + #elif ENABLED(MAGNETIC_PARKING_EXTRUDER) + + #define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point + #define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple + #define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point + #define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling + + #endif + +#endif + +/** + * Switching Toolhead + * + * Support for swappable and dockable toolheads, such as + * the E3D Tool Changer. Toolheads are locked with a servo. + */ +//#define SWITCHING_TOOLHEAD + +/** + * Magnetic Switching Toolhead + * + * Support swappable and dockable toolheads with a magnetic + * docking mechanism using movement and no servo. + */ +//#define MAGNETIC_SWITCHING_TOOLHEAD + +/** + * Electromagnetic Switching Toolhead + * + * Parking for CoreXY / HBot kinematics. + * Toolheads are parked at one edge and held with an electromagnet. + * Supports more than 2 Toolheads. See https://youtu.be/JolbsAKTKf4 + */ +//#define ELECTROMAGNETIC_SWITCHING_TOOLHEAD + +#if ANY(SWITCHING_TOOLHEAD, MAGNETIC_SWITCHING_TOOLHEAD, ELECTROMAGNETIC_SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_Y_POS 235 // (mm) Y position of the toolhead dock + #define SWITCHING_TOOLHEAD_Y_SECURITY 10 // (mm) Security distance Y axis + #define SWITCHING_TOOLHEAD_Y_CLEAR 60 // (mm) Minimum distance from dock for unobstructed X axis + #define SWITCHING_TOOLHEAD_X_POS { 215, 0 } // (mm) X positions for parking the extruders + #if ENABLED(SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_SERVO_NR 2 // Index of the servo connector + #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock + #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif + #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching + #endif +#endif + +/** + * "Mixing Extruder" + * - Adds G-codes M163 and M164 to set and "commit" the current mix factors. + * - Extends the stepping routines to move multiple steppers in proportion to the mix. + * - Optional support for Repetier Firmware's 'M164 S' supporting virtual tools. + * - This implementation supports up to two mixing extruders. + * - Enable DIRECT_MIXING_IN_G1 for M165 and mixing in G1 (from Pia Taubert's reference implementation). + */ +//#define MIXING_EXTRUDER +#if ENABLED(MIXING_EXTRUDER) + #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder + #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164 + //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands + //#define GRADIENT_MIX // Support for gradient mixing with M166 and LCD + #if ENABLED(GRADIENT_MIX) + //#define GRADIENT_VTOOL // Add M166 T to use a V-tool index as a Gradient alias + #endif +#endif + +// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). +// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). +// For the other hotends it is their distance from the extruder 0 hotend. +//#define HOTEND_OFFSET_X { 0.0, 20.00 } // (mm) relative X-offset for each nozzle +//#define HOTEND_OFFSET_Y { 0.0, 5.00 } // (mm) relative Y-offset for each nozzle +//#define HOTEND_OFFSET_Z { 0.0, 0.00 } // (mm) relative Z-offset for each nozzle + +// @section machine + +/** + * Power Supply Control + * + * Enable and connect the power supply to the PS_ON_PIN. + * Specify whether the power supply is active HIGH or active LOW. + */ +//#define PSU_CONTROL +//#define PSU_NAME "Power Supply" + +#if ENABLED(PSU_CONTROL) + #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2) + + //#define PS_DEFAULT_OFF // Keep power off until enabled directly with M80 + + //#define AUTO_POWER_CONTROL // Enable automatic control of the PS_ON pin + #if ENABLED(AUTO_POWER_CONTROL) + #define AUTO_POWER_FANS // Turn on PSU if fans need power + #define AUTO_POWER_E_FANS + #define AUTO_POWER_CONTROLLERFAN + #define AUTO_POWER_CHAMBER_FAN + //#define AUTO_POWER_E_TEMP 50 // (°C) Turn on PSU over this temperature + //#define AUTO_POWER_CHAMBER_TEMP 30 // (°C) Turn on PSU over this temperature + #define POWER_TIMEOUT 30 + #endif +#endif + +// @section temperature + +//=========================================================================== +//============================= Thermal Settings ============================ +//=========================================================================== + +/** + * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table + * + * Temperature sensors available: + * + * -4 : thermocouple with AD8495 + * -3 : thermocouple with MAX31855 (only for sensor 0) + * -2 : thermocouple with MAX6675 (only for sensor 0) + * -1 : thermocouple with AD595 + * 0 : not used + * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 3 : Mendel-parts thermistor (4.7k pullup) + * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! + * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) + * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) + * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) + * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) + * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) + * 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) + * 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) + * 10 : 100k RS thermistor 198-961 (4.7k pullup) + * 11 : 100k beta 3950 1% thermistor (4.7k pullup) + * 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) + * 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" + * 15 : 100k thermistor calibration for JGAurora A5 hotend + * 18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327 + * 20 : the PT100 circuit found in the Ultimainboard V2.x + * 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 + * 61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup + * 66 : 4.7M High Temperature thermistor from Dyze Design + * 67 : 450C thermistor from SliceEngineering + * 70 : the 100K thermistor found in the bq Hephestos 2 + * 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor + * + * 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k. + * (but gives greater accuracy and more stable PID) + * 51 : 100k thermistor - EPCOS (1k pullup) + * 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup) + * 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) + * + * 1047 : Pt1000 with 4k7 pullup + * 1010 : Pt1000 with 1k pullup (non standard) + * 147 : Pt100 with 4k7 pullup + * 110 : Pt100 with 1k pullup (non standard) + * + * 1000 : Custom - Specify parameters in Configuration_adv.h + * + * Use these for Testing or Development purposes. NEVER for production machine. + * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. + * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. + * + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + */ +#define TEMP_SENSOR_0 1 +#define TEMP_SENSOR_1 0 +#define TEMP_SENSOR_2 0 +#define TEMP_SENSOR_3 0 +#define TEMP_SENSOR_4 0 +#define TEMP_SENSOR_5 0 +#define TEMP_SENSOR_BED 1 +#define TEMP_SENSOR_CHAMBER 0 + +// Dummy thermistor constant temperature readings, for use with 998 and 999 +#define DUMMY_THERMISTOR_998_VALUE 25 +#define DUMMY_THERMISTOR_999_VALUE 100 + +// Use temp sensor 1 as a redundant sensor with sensor 0. If the readings +// from the two sensors differ too much the print will be aborted. +//#define TEMP_SENSOR_1_AS_REDUNDANT +#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 + +#define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109 +#define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer +#define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target + +#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190 +#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer +#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target + +// Below this temperature the heater will be switched off +// because it probably indicates a broken thermistor wire. +#define HEATER_0_MINTEMP 5 +#define HEATER_1_MINTEMP 5 +#define HEATER_2_MINTEMP 5 +#define HEATER_3_MINTEMP 5 +#define HEATER_4_MINTEMP 5 +#define HEATER_5_MINTEMP 5 +#define BED_MINTEMP 5 + +// Above this temperature the heater will be switched off. +// This can protect components from overheating, but NOT from shorts and failures. +// (Use MINTEMP for thermistor short/failure protection.) +#define HEATER_0_MAXTEMP 275 +#define HEATER_1_MAXTEMP 275 +#define HEATER_2_MAXTEMP 275 +#define HEATER_3_MAXTEMP 275 +#define HEATER_4_MAXTEMP 275 +#define HEATER_5_MAXTEMP 275 +#define BED_MAXTEMP 150 + +//=========================================================================== +//============================= PID Settings ================================ +//=========================================================================== +// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning + +// Comment the following line to disable PID and enable bang-bang. +#define PIDTEMP +#define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current +#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current +#define PID_K1 0.95 // Smoothing factor within any PID loop +#if ENABLED(PIDTEMP) + //#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM) + //#define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM) + //#define PID_DEBUG // Sends debug data to the serial port. + //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX + //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay + //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] + #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature + // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. + + // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it + + // Alfawise U30/U20 + // Please refine the PID settings for your own machine to avoid the E1 hotend error. These a basic settings allowing first startups. + // Use the command M303 E0 S200 C8 each time you make any changes to your extruder + + #define DEFAULT_Kp 17.22 + #define DEFAULT_Ki 1.00 + #define DEFAULT_Kd 74.22 + + + // MakerGear + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 + + // Mendel Parts V9 on 12V + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 + +#endif // PIDTEMP + +//=========================================================================== +//====================== PID > Bed Temperature Control ====================== +//=========================================================================== + +/** + * PID Bed Heating + * + * If this option is enabled set PID constants below. + * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis. + * + * The PID frequency will be the same as the extruder PWM. + * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz, + * which is fine for driving a square wave into a resistive load and does not significantly + * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W + * heater. If your configuration is significantly different than this and you don't understand + * the issues involved, don't use bed PID until someone else verifies that your hardware works. + */ +#define PIDTEMPBED + +//#define BED_LIMIT_SWITCHING + +/** + * Max Bed Power + * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis). + * When set to any value below 255, enables a form of PWM to the bed that acts like a divider + * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED) + */ +#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current + +#if ENABLED(PIDTEMPBED) + //#define MIN_BED_POWER 0 + //#define PID_BED_DEBUG // Sends debug data to the serial port. + + //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) + //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) + //#define DEFAULT_bedKp 10.00 + //#define DEFAULT_bedKi .023 + //#define DEFAULT_bedKd 305.4 + + //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) + //from pidautotune + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 + +#if ENABLED(U30) + //From M303 command for Alfawise U30 : + #define DEFAULT_bedKp 338.46 + #define DEFAULT_bedKi 63.96 + #define DEFAULT_bedKd 447.78 +#endif + +#if ENABLED(U20) + //From M303 command for Alfawise U20 : + #define DEFAULT_bedKp 841.68 + #define DEFAULT_bedKi 152.12 + #define DEFAULT_bedKd 1164.25 +#endif + +#if ENABLED(U20_PLUS) // The PID setting MUST be updated. + //From M303 command for Alfawise U20 : + #define DEFAULT_bedKp 841.68 + #define DEFAULT_bedKi 152.12 + #define DEFAULT_bedKd 1164.25 +#endif + // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. +#endif // PIDTEMPBED + +// @section extruder + +/** + * Prevent extrusion if the temperature is below EXTRUDE_MINTEMP. + * Add M302 to set the minimum extrusion temperature and/or turn + * cold extrusion prevention on and off. + * + * *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! *** + */ +#define PREVENT_COLD_EXTRUSION +#define EXTRUDE_MINTEMP 170 + +/** + * Prevent a single extrusion longer than EXTRUDE_MAXLENGTH. + * Note: For Bowden Extruders make this large enough to allow load/unload. + */ +#define PREVENT_LENGTHY_EXTRUDE +#define EXTRUDE_MAXLENGTH 200 + +//=========================================================================== +//======================== Thermal Runaway Protection ======================= +//=========================================================================== + +/** + * Thermal Protection provides additional protection to your printer from damage + * and fire. Marlin always includes safe min and max temperature ranges which + * protect against a broken or disconnected thermistor wire. + * + * The issue: If a thermistor falls out, it will report the much lower + * temperature of the air in the room, and the the firmware will keep + * the heater on. + * + * If you get "Thermal Runaway" or "Heating failed" errors the + * details can be tuned in Configuration_adv.h + */ + +#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders +#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed +//#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber + +//=========================================================================== +//============================= Mechanical Settings ========================= +//=========================================================================== + +// @section machine + +// Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics +// either in the usual order or reversed +//#define COREXY +//#define COREXZ +//#define COREYZ +//#define COREYX +//#define COREZX +//#define COREZY + +//=========================================================================== +//============================== Endstop Settings =========================== +//=========================================================================== + +// @section homing + +// Specify here all the endstop connectors that are connected to any endstop or probe. +// Almost all printers will be using one per axis. Probes will use one or more of the +// extra connectors. Leave undefined any used for non-endstop and non-probe purposes. +#define USE_XMIN_PLUG +#define USE_YMIN_PLUG +#define USE_ZMIN_PLUG +//#define USE_XMAX_PLUG +//#define USE_YMAX_PLUG +//#define USE_ZMAX_PLUG + +// Enable pullup for all endstops to prevent a floating state +//#define ENDSTOPPULLUPS +#if DISABLED(ENDSTOPPULLUPS) + // Disable ENDSTOPPULLUPS to set pullups individually + //#define ENDSTOPPULLUP_XMAX + //#define ENDSTOPPULLUP_YMAX + //#define ENDSTOPPULLUP_ZMAX + //#define ENDSTOPPULLUP_XMIN + //#define ENDSTOPPULLUP_YMIN + //#define ENDSTOPPULLUP_ZMIN + //#define ENDSTOPPULLUP_ZMIN_PROBE +#endif + +// Enable pulldown for all endstops to prevent a floating state +//#define ENDSTOPPULLDOWNS +#if DISABLED(ENDSTOPPULLDOWNS) + // Disable ENDSTOPPULLDOWNS to set pulldowns individually + //#define ENDSTOPPULLDOWN_XMAX + //#define ENDSTOPPULLDOWN_YMAX + //#define ENDSTOPPULLDOWN_ZMAX + //#define ENDSTOPPULLDOWN_XMIN + //#define ENDSTOPPULLDOWN_YMIN + //#define ENDSTOPPULLDOWN_ZMIN + //#define ENDSTOPPULLDOWN_ZMIN_PROBE +#endif + +// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup). +#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop. +#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop. +#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop. +#define X_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop. +#define Y_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop. +#define Z_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop. +#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe. + +/** + * Stepper Drivers + * + * These settings allow Marlin to tune stepper driver timing and enable advanced options for + * stepper drivers that support them. You may also override timing options in Configuration_adv.h. + * + * A4988 is assumed for unspecified drivers. + * + * Options: A4988, A5984, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100, + * TMC2130, TMC2130_STANDALONE, TMC2160, TMC2160_STANDALONE, + * TMC2208, TMC2208_STANDALONE, TMC2209, TMC2209_STANDALONE, + * TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE, + * TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE + * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE'] + */ +#define X_DRIVER_TYPE A4988 +#define Y_DRIVER_TYPE A4988 +#define Z_DRIVER_TYPE A4988 +//#define X2_DRIVER_TYPE A4988 +//#define Y2_DRIVER_TYPE A4988 +//#define Z2_DRIVER_TYPE A4988 +//#define Z3_DRIVER_TYPE A4988 +#define E0_DRIVER_TYPE A4988 +//#define E1_DRIVER_TYPE A4988 +//#define E2_DRIVER_TYPE A4988 +//#define E3_DRIVER_TYPE A4988 +//#define E4_DRIVER_TYPE A4988 +//#define E5_DRIVER_TYPE A4988 + +// Enable this feature if all enabled endstop pins are interrupt-capable. +// This will remove the need to poll the interrupt pins, saving many CPU cycles. +#define ENDSTOP_INTERRUPTS_FEATURE + +/** + * Endstop Noise Threshold + * + * Enable if your probe or endstops falsely trigger due to noise. + * + * - Higher values may affect repeatability or accuracy of some bed probes. + * - To fix noise install a 100nF ceramic capacitor inline with the switch. + * - This feature is not required for common micro-switches mounted on PCBs + * based on the Makerbot design, which already have the 100nF capacitor. + * + * :[2,3,4,5,6,7] + */ +//#define ENDSTOP_NOISE_THRESHOLD 2 + +//============================================================================= +//============================== Movement Settings ============================ +//============================================================================= +// @section motion + +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * With this option each E stepper can have its own factors for the + * following movement settings. If fewer factors are given than the + * total number of extruders, the last value applies to the rest. + */ +//#define DISTINCT_E_FACTORS + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] + */ +#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 98 } + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] + */ +#define DEFAULT_MAX_FEEDRATE { 200, 200, 100, 25 } + +/** + * Default Max Acceleration (change/s) change = mm/s + * (Maximum start speed for accelerated moves) + * Override with M201 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] + */ +#define DEFAULT_MAX_ACCELERATION { 200, 200, 100, 3000 } + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 200 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 500 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 200 // X, Y, Z acceleration for travel (non printing) moves + +/** + * Junction Deviation + * + * Use Junction Deviation instead of traditional Jerk Limiting + * + * See: + * https://reprap.org/forum/read.php?1,739819 + * http://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html + */ +//#define JUNCTION_DEVIATION +#if ENABLED(JUNCTION_DEVIATION) + #define JUNCTION_DEVIATION_MM 0.02 // (mm) Distance from real junction edge +#endif + +/** + * Default Jerk (mm/s) + * Override with M205 X Y Z E + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#if DISABLED(JUNCTION_DEVIATION) + #define DEFAULT_XJERK 10.0 + #define DEFAULT_YJERK 10.0 + #define DEFAULT_ZJERK 0.4 +#endif + +#define DEFAULT_EJERK 5.0 // May be used by Linear Advance + +/** + * S-Curve Acceleration + * + * This option eliminates vibration during printing by fitting a Bézier + * curve to move acceleration, producing much smoother direction changes. + * + * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained + */ +//#define S_CURVE_ACCELERATION + +//=========================================================================== +//============================= Z Probe Options ============================= +//=========================================================================== +// @section probes + +// +// See http://marlinfw.org/docs/configuration/probes.html +// + +/** + * Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + * + * Enable this option for a probe connected to the Z Min endstop pin. + */ +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +/** + * Z_MIN_PROBE_PIN + * + * Define this pin if the probe is not connected to Z_MIN_PIN. + * If not defined the default pin for the selected MOTHERBOARD + * will be used. Most of the time the default is what you want. + * + * - The simplest option is to use a free endstop connector. + * - Use 5V for powered (usually inductive) sensors. + * + * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin: + * - For simple switches connect... + * - normally-closed switches to GND and D32. + * - normally-open switches to 5V and D32. + * + */ +//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default + +/** + * Probe Type + * + * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. + * Activate one of these to use Auto Bed Leveling below. + */ + +/** + * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe. + * Use G29 repeatedly, adjusting the Z height at each point with movement commands + * or (with LCD_BED_LEVELING) the LCD controller. + */ +#define PROBE_MANUALLY +#define MANUAL_PROBE_START_Z 0.2 + +/** + * A Fix-Mounted Probe either doesn't deploy or needs manual deployment. + * (e.g., an inductive probe or a nozzle-based probe-switch.) + */ +//#define FIX_MOUNTED_PROBE + +/** + * Z Servo Probe, such as an endstop switch on a rotating arm. + */ +//#define Z_PROBE_SERVO_NR 0 // Defaults to SERVO 0 connector. +//#define Z_SERVO_ANGLES { 70, 0 } // Z Servo Deploy and Stow angles + +/** + * The BLTouch probe uses a Hall effect sensor and emulates a servo. + */ +//#define BLTOUCH + +/** + * Touch-MI Probe by hotends.fr + * + * This probe is deployed and activated by moving the X-axis to a magnet at the edge of the bed. + * By default, the magnet is assumed to be on the left and activated by a home. If the magnet is + * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position. + * + * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING, + * and a minimum Z_HOMING_HEIGHT of 10. + */ +//#define TOUCH_MI_PROBE +#if ENABLED(TOUCH_MI_PROBE) + #undef PROBE_MANUALLY + #define TOUCH_MI_RETRACT_Z 0.5 // Height at which the probe retracts + //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2) // For a magnet on the right side of the bed + //#define TOUCH_MI_MANUAL_DEPLOY // For manual deploy (LCD menu) +#endif + +// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) +//#define SOLENOID_PROBE + +// A sled-mounted probe like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +// A probe deployed by moving the x-axis, such as the Wilson II's rack-and-pinion probe designed by Marty Rice. +//#define RACK_AND_PINION_PROBE +#if ENABLED(RACK_AND_PINION_PROBE) + #define Z_PROBE_DEPLOY_X X_MIN_POS + #define Z_PROBE_RETRACT_X X_MAX_POS +#endif + +// +// For Z_PROBE_ALLEN_KEY see the Delta example configurations. +// + +/** + * Z Probe to nozzle (X,Y) offset, relative to (0, 0). + * X and Y offsets must be integers. + * + * In the following example the X and Y offsets are both positive: + * #define X_PROBE_OFFSET_FROM_EXTRUDER 10 + * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 + * + * +-- BACK ---+ + * | | + * L | (+) P | R <-- probe (20,20) + * E | | I + * F | (-) N (+) | G <-- nozzle (10,10) + * T | | H + * | (-) | T + * | | + * O-- FRONT --+ + * (0,0) + */ +#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle] + +// Certain types of probes need to stay away from edges +#define MIN_PROBE_EDGE 10 + +// X and Y axis travel speed (mm/m) between probes +#define XY_PROBE_SPEED 8000 + +// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2) +#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z + +// Feedrate (mm/m) for the "accurate" probe of each point +#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) + +/** + * Multiple Probing + * + * You may get improved results by probing 2 or more times. + * With EXTRA_PROBING the more atypical reading(s) will be disregarded. + * + * A total of 2 does fast/slow probes with a weighted average. + * A total of 3 or more adds more slow probes, taking the average. + */ +//#define MULTIPLE_PROBING 2 +//#define EXTRA_PROBING 1 + +/** + * Z probes require clearance when deploying, stowing, and moving between + * probe points to avoid hitting the bed and other hardware. + * Servo-mounted probes require extra space for the arm to rotate. + * Inductive probes need space to keep from triggering early. + * + * Use these settings to specify the distance (mm) to raise the probe (or + * lower the bed). The values set here apply over and above any (negative) + * probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD. + * Only integer values >= 1 are valid here. + * + * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle. + * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle. + */ +#define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow +#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points +#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes +//#define Z_AFTER_PROBING 5 // Z position after probing is done + +#define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping + +// For M851 give a range for adjusting the Z probe offset +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + +// Enable the M48 repeatability test to test probe accuracy +//#define Z_MIN_PROBE_REPEATABILITY_TEST + +// Before deploy/stow pause for user confirmation +//#define PAUSE_BEFORE_DEPLOY_STOW +#if ENABLED(PAUSE_BEFORE_DEPLOY_STOW) + //#define PAUSE_PROBE_DEPLOY_WHEN_TRIGGERED // For Manual Deploy Allenkey Probe +#endif + +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + +// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 +// :{ 0:'Low', 1:'High' } +#define X_ENABLE_ON 0 +#define Y_ENABLE_ON 0 +#define Z_ENABLE_ON 0 +#define E_ENABLE_ON 0 // For all extruders + +// Disables axis stepper immediately when it's not being used. +// WARNING: When motors turn off there is a chance of losing position accuracy! +#define DISABLE_X false +#define DISABLE_Y false +#define DISABLE_Z false + +// Warn on display about possibly reduced accuracy +//#define DISABLE_REDUCED_ACCURACY_WARNING + +// @section extruder + +#define DISABLE_E false // For all extruders +#define DISABLE_INACTIVE_EXTRUDER // Keep only the active extruder enabled + +// @section machine + +// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way. +#define INVERT_X_DIR true +#define INVERT_Y_DIR false +#define INVERT_Z_DIR true + +// @section extruder + +// For direct drive extruder v9 set to true, for geared extruder set to false. +#define INVERT_E0_DIR false +#define INVERT_E1_DIR false +#define INVERT_E2_DIR false +#define INVERT_E3_DIR false +#define INVERT_E4_DIR false +#define INVERT_E5_DIR false + +// @section homing + +//#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed + +//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off. + +//#define Z_HOMING_HEIGHT 10 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ... + // Be sure you have this distance over your Z_MAX_POS in case. + +// Direction of endstops when homing; 1=MAX, -1=MIN +// :[-1,1] +#define X_HOME_DIR -1 +#define Y_HOME_DIR -1 +#define Z_HOME_DIR -1 + +// @section machine + +#if ENABLED(U30) +#define X_BED_SIZE 220 +#define Y_BED_SIZE 220 +#define Z_MACHINE_MAX 250 +#endif + +#if ENABLED(U20) +#define X_BED_SIZE 300 +#define Y_BED_SIZE 300 +#define Z_MACHINE_MAX 400 +#endif + +#if ENABLED(U20_PLUS) +#define X_BED_SIZE 400 +#define Y_BED_SIZE 400 +#define Z_MACHINE_MAX 500 +#endif + +// Travel limits (mm) after homing, corresponding to endstop positions. +#define X_MIN_POS 0 +#define Y_MIN_POS 0 +#define Z_MIN_POS 0 +#define X_MAX_POS X_BED_SIZE +#define Y_MAX_POS Y_BED_SIZE +#define Z_MAX_POS Z_MACHINE_MAX + +/** + * Software Endstops + * + * - Prevent moves outside the set machine bounds. + * - Individual axes can be disabled, if desired. + * - X and Y only apply to Cartesian robots. + * - Use 'M211' to set software endstops on/off or report current state + */ + +// Min software endstops constrain movement within minimum coordinate bounds +#define MIN_SOFTWARE_ENDSTOPS +#if ENABLED(MIN_SOFTWARE_ENDSTOPS) + #define MIN_SOFTWARE_ENDSTOP_X + #define MIN_SOFTWARE_ENDSTOP_Y + #define MIN_SOFTWARE_ENDSTOP_Z +#endif + +// Max software endstops constrain movement within maximum coordinate bounds +#define MAX_SOFTWARE_ENDSTOPS +#if ENABLED(MAX_SOFTWARE_ENDSTOPS) + #define MAX_SOFTWARE_ENDSTOP_X + #define MAX_SOFTWARE_ENDSTOP_Y + #define MAX_SOFTWARE_ENDSTOP_Z +#endif + +#if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS) + //#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD +#endif + +/** + * Filament Runout Sensors + * Mechanical or opto endstops are used to check for the presence of filament. + * + * RAMPS-based boards use SERVO3_PIN for the first runout sensor. + * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc. + * By default the firmware assumes HIGH=FILAMENT PRESENT. + */ +#define FILAMENT_RUNOUT_SENSOR +#if ENABLED(FILAMENT_RUNOUT_SENSOR) + #define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each. + #define FIL_RUNOUT_INVERTING true // Set to true to invert the logic of the sensor. + //#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins. + //#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins. + + // Set one or more commands to execute on filament runout. + // (After 'M412 H' Marlin will ask the host to handle the process.) + #define FILAMENT_RUNOUT_SCRIPT "M600" + + // After a runout is detected, continue printing this length of filament + // before executing the runout script. Useful for a sensor at the end of + // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead. + //#define FILAMENT_RUNOUT_DISTANCE_MM 25 + + #ifdef FILAMENT_RUNOUT_DISTANCE_MM + // Enable this option to use an encoder disc that toggles the runout pin + // as the filament moves. (Be sure to set FILAMENT_RUNOUT_DISTANCE_MM + // large enough to avoid false positives.) + //#define FILAMENT_MOTION_SENSOR + #endif +#endif + +//=========================================================================== +//=============================== Bed Leveling ============================== +//=========================================================================== +// @section calibrate + +/** + * Choose one of the options below to enable G29 Bed Leveling. The parameters + * and behavior of G29 will change depending on your selection. + * + * If using a Probe for Z Homing, enable Z_SAFE_HOMING also! + * + * - AUTO_BED_LEVELING_3POINT + * Probe 3 arbitrary points on the bed (that aren't collinear) + * You specify the XY coordinates of all 3 points. + * The result is a single tilted plane. Best for a flat bed. + * + * - AUTO_BED_LEVELING_LINEAR + * Probe several points in a grid. + * You specify the rectangle and the density of sample points. + * The result is a single tilted plane. Best for a flat bed. + * + * - AUTO_BED_LEVELING_BILINEAR + * Probe several points in a grid. + * You specify the rectangle and the density of sample points. + * The result is a mesh, best for large or uneven beds. + * + * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling) + * A comprehensive bed leveling system combining the features and benefits + * of other systems. UBL also includes integrated Mesh Generation, Mesh + * Validation and Mesh Editing systems. + * + * - MESH_BED_LEVELING + * Probe a grid manually + * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.) + * For machines without a probe, Mesh Bed Leveling provides a method to perform + * leveling in steps so you can manually adjust the Z height at each grid-point. + * With an LCD controller the process is guided step-by-step. + */ +//#define AUTO_BED_LEVELING_3POINT +//#define AUTO_BED_LEVELING_LINEAR +//#define AUTO_BED_LEVELING_BILINEAR +//#define AUTO_BED_LEVELING_UBL +#define MESH_BED_LEVELING + +/** + * Normally G28 leaves leveling disabled on completion. Enable + * this option to have G28 restore the prior leveling state. + */ +//#define RESTORE_LEVELING_AFTER_G28 + +/** + * Enable detailed logging of G28, G29, M48, etc. + * Turn on with the command 'M111 S32'. + * NOTE: Requires a lot of PROGMEM! + */ +//#define DEBUG_LEVELING_FEATURE + +#if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_BILINEAR, AUTO_BED_LEVELING_UBL) + // Gradually reduce leveling correction until a set height is reached, + // at which point movement will be level to the machine's XY plane. + // The height can be set with M420 Z + #define ENABLE_LEVELING_FADE_HEIGHT + + // For Cartesian machines, instead of dividing moves on mesh boundaries, + // split up moves into short segments like a Delta. This follows the + // contours of the bed more closely than edge-to-edge straight moves. + #define SEGMENT_LEVELED_MOVES + #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one) + + /** + * Enable the G26 Mesh Validation Pattern tool. + */ + //#define G26_MESH_VALIDATION + #if ENABLED(G26_MESH_VALIDATION) + #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle. + #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool. + #define MESH_TEST_HOTEND_TEMP 205 // (°C) Default nozzle temperature for the G26 Mesh Validation Tool. + #define MESH_TEST_BED_TEMP 60 // (°C) Default bed temperature for the G26 Mesh Validation Tool. + #define G26_XY_FEEDRATE 20 // (mm/s) Feedrate for XY Moves for the G26 Mesh Validation Tool. + #endif + +#endif + +#if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR) + + // Set the number of grid points per dimension. + #define GRID_MAX_POINTS_X 3 + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + // Set the boundaries for probing (where the probe can reach). + //#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE + //#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE)) + //#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE + //#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE)) + + // Probe along the Y axis, advancing X after each column + //#define PROBE_Y_FIRST + + #if ENABLED(AUTO_BED_LEVELING_BILINEAR) + + // Beyond the probed grid, continue the implied tilt? + // Default is to maintain the height of the nearest edge. + //#define EXTRAPOLATE_BEYOND_GRID + + // + // Experimental Subdivision of the grid by Catmull-Rom method. + // Synthesizes intermediate points to produce a more detailed mesh. + // + //#define ABL_BILINEAR_SUBDIVISION + #if ENABLED(ABL_BILINEAR_SUBDIVISION) + // Number of subdivisions between probe points + #define BILINEAR_SUBDIVISIONS 3 + #endif + + #endif + +#elif ENABLED(AUTO_BED_LEVELING_UBL) + + //=========================================================================== + //========================= Unified Bed Leveling ============================ + //=========================================================================== + + //#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh + + #define MESH_INSET 1 // Set Mesh bounds as an inset region of the bed + #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited. + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + #define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle + #define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500 + + //#define UBL_Z_RAISE_WHEN_OFF_MESH 2.5 // When the nozzle is off the mesh, this value is used + // as the Z-Height correction value. + +#elif ENABLED(MESH_BED_LEVELING) + + //=========================================================================== + //=================================== Mesh ================================== + //=========================================================================== + + #define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed + #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited. + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS + +#endif // BED_LEVELING + +/** + * Points to probe for all 3-point Leveling procedures. + * Override if the automatically selected points are inadequate. + */ +#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL) + //#define PROBE_PT_1_X 15 + //#define PROBE_PT_1_Y 180 + //#define PROBE_PT_2_X 15 + //#define PROBE_PT_2_Y 20 + //#define PROBE_PT_3_X 170 + //#define PROBE_PT_3_Y 20 +#endif + +/** + * Add a bed leveling sub-menu for ABL or MBL. + * Include a guided procedure if manual probing is enabled. + */ +//#define LCD_BED_LEVELING + +#if ENABLED(LCD_BED_LEVELING) + #define MESH_EDIT_Z_STEP 0.025 // (mm) Step size while manually probing Z axis. + #define LCD_PROBE_Z_RANGE 4 // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment + //#define MESH_EDIT_MENU // Add a menu to edit mesh points +#endif + +// Add a menu item to move between bed corners for manual bed adjustment +#define LEVEL_BED_CORNERS + +#if ENABLED(LEVEL_BED_CORNERS) + #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + #define LEVEL_CENTER_TOO // Move to the center after the last corner +#endif + +/** + * Commands to execute at the end of G29 probing. + * Useful to retract or move the Z probe out of the way. + */ +//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" + + +// @section homing + +// The center of the bed is at (X=0, Y=0) +//#define BED_CENTER_AT_0_0 + +// Manually set the home position. Leave these undefined for automatic settings. +// For DELTA this is the top-center of the Cartesian print volume. +//#define MANUAL_X_HOME_POS 0 +//#define MANUAL_Y_HOME_POS 0 +//#define MANUAL_Z_HOME_POS 0 + +// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area. +// +// With this feature enabled: +// +// - Allow Z homing only after X and Y homing AND stepper drivers still enabled. +// - If stepper drivers time out, it will need X and Y homing again before Z homing. +// - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28). +// - Prevent Z homing when the Z probe is outside bed area. +// +//#define Z_SAFE_HOMING + +#if ENABLED(Z_SAFE_HOMING) + #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing when homing all axes (G28). + #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2) // Y point for Z homing when homing all axes (G28). +#endif + +// Homing speeds (mm/m) +#define HOMING_FEEDRATE_XY (20*60) +#define HOMING_FEEDRATE_Z (7*60) + +// Validate that endstops are triggered on homing moves +#define VALIDATE_HOMING_ENDSTOPS + +// @section calibrate + +/** + * Bed Skew Compensation + * + * This feature corrects for misalignment in the XYZ axes. + * + * Take the following steps to get the bed skew in the XY plane: + * 1. Print a test square (e.g., https://www.thingiverse.com/thing:2563185) + * 2. For XY_DIAG_AC measure the diagonal A to C + * 3. For XY_DIAG_BD measure the diagonal B to D + * 4. For XY_SIDE_AD measure the edge A to D + * + * Marlin automatically computes skew factors from these measurements. + * Skew factors may also be computed and set manually: + * + * - Compute AB : SQRT(2*AC*AC+2*BD*BD-4*AD*AD)/2 + * - XY_SKEW_FACTOR : TAN(PI/2-ACOS((AC*AC-AB*AB-AD*AD)/(2*AB*AD))) + * + * If desired, follow the same procedure for XZ and YZ. + * Use these diagrams for reference: + * + * Y Z Z + * ^ B-------C ^ B-------C ^ B-------C + * | / / | / / | / / + * | / / | / / | / / + * | A-------D | A-------D | A-------D + * +-------------->X +-------------->X +-------------->Y + * XY_SKEW_FACTOR XZ_SKEW_FACTOR YZ_SKEW_FACTOR + */ +//#define SKEW_CORRECTION + +#if ENABLED(SKEW_CORRECTION) + // Input all length measurements here: + #define XY_DIAG_AC 282.8427124746 + #define XY_DIAG_BD 282.8427124746 + #define XY_SIDE_AD 200 + + // Or, set the default skew factors directly here + // to override the above measurements: + #define XY_SKEW_FACTOR 0.0 + + //#define SKEW_CORRECTION_FOR_Z + #if ENABLED(SKEW_CORRECTION_FOR_Z) + #define XZ_DIAG_AC 282.8427124746 + #define XZ_DIAG_BD 282.8427124746 + #define YZ_DIAG_AC 282.8427124746 + #define YZ_DIAG_BD 282.8427124746 + #define YZ_SIDE_AD 200 + #define XZ_SKEW_FACTOR 0.0 + #define YZ_SKEW_FACTOR 0.0 + #endif + + // Enable this option for M852 to set skew at runtime + //#define SKEW_CORRECTION_GCODE +#endif + +//============================================================================= +//============================= Additional Features =========================== +//============================================================================= + +// @section extras + +/** + * EEPROM + * + * Persistent storage to preserve configurable settings across reboots. + * + * M500 - Store settings to EEPROM. + * M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes) + * M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.) + */ +#define EEPROM_SETTINGS // Persistent storage with M500 and M501 +//#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release! +#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM. +#if ENABLED(EEPROM_SETTINGS) + //#define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors. +#endif + +// +// Host Keepalive +// +// When enabled Marlin will send a busy status message to the host +// every couple of seconds when it can't accept commands. +// +#define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages +#define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113. +#define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating + +// +// M100 Free Memory Watcher +// +//#define M100_FREE_MEMORY_WATCHER // Add M100 (Free Memory Watcher) to debug memory usage + +// +// G20/G21 Inch mode support +// +//#define INCH_MODE_SUPPORT + +// +// M149 Set temperature units support +// +//#define TEMPERATURE_UNITS_SUPPORT + +// @section temperature + +// Preheat Constants +#define PREHEAT_1_LABEL "PLA" +#define PREHEAT_1_TEMP_HOTEND 200 +#define PREHEAT_1_TEMP_BED 60 +#define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255 + +#define PREHEAT_2_LABEL "ABS" +#define PREHEAT_2_TEMP_HOTEND 250 +#define PREHEAT_2_TEMP_BED 100 +#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255 + +/** + * Nozzle Park + * + * Park the nozzle at the given XYZ position on idle or G27. + * + * The "P" parameter controls the action applied to the Z axis: + * + * P0 (Default) If Z is below park Z raise the nozzle. + * P1 Raise the nozzle always to Z-park height. + * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS. + */ +#define NOZZLE_PARK_FEATURE + +#if ENABLED(NOZZLE_PARK_FEATURE) + // Specify a park position as { X, Y, Z_raise } + #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 } + #define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis) + #define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers) +#endif + +/** + * Clean Nozzle Feature -- EXPERIMENTAL + * + * Adds the G12 command to perform a nozzle cleaning process. + * + * Parameters: + * P Pattern + * S Strokes / Repetitions + * T Triangles (P1 only) + * + * Patterns: + * P0 Straight line (default). This process requires a sponge type material + * at a fixed bed location. "S" specifies strokes (i.e. back-forth motions) + * between the start / end points. + * + * P1 Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the + * number of zig-zag triangles to do. "S" defines the number of strokes. + * Zig-zags are done in whichever is the narrower dimension. + * For example, "G12 P1 S1 T3" will execute: + * + * -- + * | (X0, Y1) | /\ /\ /\ | (X1, Y1) + * | | / \ / \ / \ | + * A | | / \ / \ / \ | + * | | / \ / \ / \ | + * | (X0, Y0) | / \/ \/ \ | (X1, Y0) + * -- +--------------------------------+ + * |________|_________|_________| + * T1 T2 T3 + * + * P2 Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE. + * "R" specifies the radius. "S" specifies the stroke count. + * Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT. + * + * Caveats: The ending Z should be the same as starting Z. + * Attention: EXPERIMENTAL. G-code arguments may change. + * + */ +//#define NOZZLE_CLEAN_FEATURE + +#if ENABLED(NOZZLE_CLEAN_FEATURE) + // Default number of pattern repetitions + #define NOZZLE_CLEAN_STROKES 12 + + // Default number of triangles + #define NOZZLE_CLEAN_TRIANGLES 3 + + // Specify positions as { X, Y, Z } + #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)} + #define NOZZLE_CLEAN_END_POINT { 100, 60, (Z_MIN_POS + 1) } + + // Circular pattern radius + #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5 + // Circular pattern circle fragments number + #define NOZZLE_CLEAN_CIRCLE_FN 10 + // Middle point of circle + #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT + + // Move the nozzle to the initial position after cleaning + #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z +#endif + +/** + * Print Job Timer + * + * Automatically start and stop the print job timer on M104/M109/M190. + * + * M104 (hotend, no wait) - high temp = none, low temp = stop timer + * M109 (hotend, wait) - high temp = start timer, low temp = stop timer + * M190 (bed, wait) - high temp = start timer, low temp = none + * + * The timer can also be controlled with the following commands: + * + * M75 - Start the print job timer + * M76 - Pause the print job timer + * M77 - Stop the print job timer + */ +#define PRINTJOB_TIMER_AUTOSTART + +/** + * Print Counter + * + * Track statistical data such as: + * + * - Total print jobs + * - Total successful print jobs + * - Total failed print jobs + * - Total time printing + * + * View the current statistics with M78. + */ +//#define PRINTCOUNTER + +//============================================================================= +//============================= LCD and SD support ============================ +//============================================================================= + +// @section lcd + +/** + * LCD LANGUAGE + * + * Select the language to display on the LCD. These languages are available: + * + * en, an, bg, ca, cz, da, de, el, el-gr, es, eu, fi, fr, gl, hr, it, + * jp-kana, ko_KR, nl, pl, pt, pt-br, ru, sk, tr, uk, zh_CN, zh_TW, test + * + * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cz':'Czech', 'da':'Danish', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'jp-kana':'Japanese', 'ko_KR':'Korean (South Korea)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'ru':'Russian', 'sk':'Slovak', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Traditional)', 'test':'TEST' } + */ +#define LCD_LANGUAGE en + +/** + * LCD Character Set + * + * Note: This option is NOT applicable to Graphical Displays. + * + * All character-based LCDs provide ASCII plus one of these + * language extensions: + * + * - JAPANESE ... the most common + * - WESTERN ... with more accented characters + * - CYRILLIC ... for the Russian language + * + * To determine the language extension installed on your controller: + * + * - Compile and upload with LCD_LANGUAGE set to 'test' + * - Click the controller to view the LCD menu + * - The LCD will display Japanese, Western, or Cyrillic text + * + * See http://marlinfw.org/docs/development/lcd_language.html + * + * :['JAPANESE', 'WESTERN', 'CYRILLIC'] + */ +#define DISPLAY_CHARSET_HD44780 JAPANESE + +/** + * Info Screen Style (0:Classic, 1:Prusa) + * + * :[0:'Classic', 1:'Prusa'] + */ +#define LCD_INFO_SCREEN_STYLE 0 + +/** + * SD CARD + * + * SD Card support is disabled by default. If your controller has an SD slot, + * you must uncomment the following option or it won't work. + * + */ +#define SDSUPPORT +#define SDIO_SUPPORT // Note from Hobi : Added as was not present in the file... + +/** + * SD CARD: SPI SPEED + * + * Enable one of the following items for a slower SPI transfer speed. + * This may be required to resolve "volume init" errors. + */ +//#define SPI_SPEED SPI_HALF_SPEED +//#define SPI_SPEED SPI_QUARTER_SPEED +//#define SPI_SPEED SPI_EIGHTH_SPEED + +/** + * SD CARD: ENABLE CRC + * + * Use CRC checks and retries on the SD communication. + */ +//#define SD_CHECK_AND_RETRY + +/** + * LCD Menu Items + * + * Disable all menus and only display the Status Screen, or + * just remove some extraneous menu items to recover space. + */ +//#define NO_LCD_MENUS +//#define SLIM_LCD_MENUS + +// +// ENCODER SETTINGS +// +// This option overrides the default number of encoder pulses needed to +// produce one step. Should be increased for high-resolution encoders. +// +//#define ENCODER_PULSES_PER_STEP 4 + +// +// Use this option to override the number of step signals required to +// move between next/prev menu items. +// +//#define ENCODER_STEPS_PER_MENU_ITEM 1 + +/** + * Encoder Direction Options + * + * Test your encoder's behavior first with both options disabled. + * + * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION. + * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION. + * Reversed Value Editing only? Enable BOTH options. + */ + +// +// This option reverses the encoder direction everywhere. +// +// Set this option if CLOCKWISE causes values to DECREASE +// +//#define REVERSE_ENCODER_DIRECTION + +// +// This option reverses the encoder direction for navigating LCD menus. +// +// If CLOCKWISE normally moves DOWN this makes it go UP. +// If CLOCKWISE normally moves UP this makes it go DOWN. +// +//#define REVERSE_MENU_DIRECTION + +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + +// +// Individual Axis Homing +// +// Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu. +// +#define INDIVIDUAL_AXIS_HOMING_MENU + +// +// SPEAKER/BUZZER +// +// If you have a speaker that can produce tones, enable it here. +// By default Marlin assumes you have a buzzer with a fixed frequency. +// +//#define SPEAKER + +// +// The duration and frequency for the UI feedback sound. +// Set these to 0 to disable audio feedback in the LCD menus. +// +// Note: Test audio output with the G-Code: +// M300 S P +// +//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 250 +//#define LCD_FEEDBACK_FREQUENCY_HZ 1000 + +//============================================================================= +//======================== LCD / Controller Selection ========================= +//======================== (Character-based LCDs) ========================= +//============================================================================= + +// +// RepRapDiscount Smart Controller. +// http://reprap.org/wiki/RepRapDiscount_Smart_Controller +// +// Note: Usually sold with a white PCB. +// +//#define REPRAP_DISCOUNT_SMART_CONTROLLER + +// +// Original RADDS LCD Display+Encoder+SDCardReader +// http://doku.radds.org/dokumentation/lcd-display/ +// +//#define RADDS_DISPLAY + +// +// ULTIMAKER Controller. +// +//#define ULTIMAKERCONTROLLER + +// +// ULTIPANEL as seen on Thingiverse. +// +//#define ULTIPANEL + +// +// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3) +// http://reprap.org/wiki/PanelOne +// +//#define PANEL_ONE + +// +// GADGETS3D G3D LCD/SD Controller +// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel +// +// Note: Usually sold with a blue PCB. +// +//#define G3D_PANEL + +// +// RigidBot Panel V1.0 +// http://www.inventapart.com/ +// +//#define RIGIDBOT_PANEL + +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// ANET and Tronxy 20x4 Controller +// +//#define ZONESTAR_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin. + // This LCD is known to be susceptible to electrical interference + // which scrambles the display. Pressing any button clears it up. + // This is a LCD2004 display with 5 analog buttons. + +// +// Generic 16x2, 16x4, 20x2, or 20x4 character-based LCD. +// +//#define ULTRA_LCD + +//============================================================================= +//======================== LCD / Controller Selection ========================= +//===================== (I2C and Shift-Register LCDs) ===================== +//============================================================================= + +// +// CONTROLLER TYPE: I2C +// +// Note: These controllers require the installation of Arduino's LiquidCrystal_I2C +// library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C +// + +// +// Elefu RA Board Control Panel +// http://www.elefu.com/index.php?route=product/product&product_id=53 +// +//#define RA_CONTROL_PANEL + +// +// Sainsmart (YwRobot) LCD Displays +// +// These require F.Malpartida's LiquidCrystal_I2C library +// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home +// +//#define LCD_SAINSMART_I2C_1602 +//#define LCD_SAINSMART_I2C_2004 + +// +// Generic LCM1602 LCD adapter +// +//#define LCM1602 + +// +// PANELOLU2 LCD with status LEDs, +// separate encoder and click inputs. +// +// Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later. +// For more info: https://github.com/lincomatic/LiquidTWI2 +// +// Note: The PANELOLU2 encoder click input can either be directly connected to +// a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1). +// +//#define LCD_I2C_PANELOLU2 + +// +// Panucatt VIKI LCD with status LEDs, +// integrated click & L/R/U/D buttons, separate encoder inputs. +// +//#define LCD_I2C_VIKI + +// +// CONTROLLER TYPE: Shift register panels +// + +// +// 2-wire Non-latching LCD SR from https://goo.gl/aJJ4sH +// LCD configuration: http://reprap.org/wiki/SAV_3D_LCD +// +//#define SAV_3DLCD + +// +// 3-wire SR LCD with strobe using 74HC4094 +// https://github.com/mikeshub/SailfishLCD +// Uses the code directly from Sailfish +// +//#define FF_INTERFACEBOARD + +//============================================================================= +//======================= LCD / Controller Selection ======================= +//========================= (Graphical LCDs) ======================== +//============================================================================= + +// +// CONTROLLER TYPE: Graphical 128x64 (DOGM) +// +// IMPORTANT: The U8glib library is required for Graphical Display! +// https://github.com/olikraus/U8glib_Arduino +// + +// +// RepRapDiscount FULL GRAPHIC Smart Controller +// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller +// +//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER + +// +// ReprapWorld Graphical LCD +// https://reprapworld.com/?products_details&products_id/1218 +// +//#define REPRAPWORLD_GRAPHICAL_LCD + +// +// Activate one of these if you have a Panucatt Devices +// Viki 2.0 or mini Viki with Graphic LCD +// http://panucatt.com +// +//#define VIKI2 +//#define miniVIKI + +// +// MakerLab Mini Panel with graphic +// controller and SD support - http://reprap.org/wiki/Mini_panel +// +//#define MINIPANEL + +// +// MaKr3d Makr-Panel with graphic controller and SD support. +// http://reprap.org/wiki/MaKr3d_MaKrPanel +// +//#define MAKRPANEL + +// +// Adafruit ST7565 Full Graphic Controller. +// https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/ +// +//#define ELB_FULL_GRAPHIC_CONTROLLER + +// +// BQ LCD Smart Controller shipped by +// default with the BQ Hephestos 2 and Witbox 2. +// +//#define BQ_LCD_SMART_CONTROLLER + +// +// Cartesio UI +// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// +//#define CARTESIO_UI + +// +// LCD for Melzi Card with Graphical LCD +// +//#define LCD_FOR_MELZI + +// +// Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder +// https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) +// +//#define ULTI_CONTROLLER + +// +// MKS MINI12864 with graphic controller and SD support +// https://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// FYSETC variant of the MINI12864 graphic controller with SD support +// https://wiki.fysetc.com/Mini12864_Panel/ +// +//#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default +//#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) +//#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// ANET and Tronxy Graphical Controller +// +// Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6 +// A clone of the RepRapDiscount full graphics display but with +// different pins/wiring (see pins_ANET_10.h). +// +//#define ANET_FULL_GRAPHICS_LCD + +// +// AZSMZ 12864 LCD with SD +// https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html +// +//#define AZSMZ_12864 + +// +// Silvergate GLCD controller +// http://github.com/android444/Silvergate +// +//#define SILVER_GATE_GLCD_CONTROLLER + +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + +//============================================================================= +//========================== Extensible UI Displays =========================== +//============================================================================= + +// +// DGUS Touch Display with DWIN OS +// +//#define DGUS_LCD + +// +// Touch-screen LCD for Malyan M200 printers +// +//#define MALYAN_LCD + +// +// Third-party or vendor-customized controller interfaces. +// Sources should be installed in 'src/lcd/extensible_ui'. +// +//#define EXTENSIBLE_UI + +//============================================================================= +//=============================== Graphical TFTs ============================== +//============================================================================= + +// +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) +// +#define FSMC_GRAPHICAL_TFT + +//============================================================================= +//============================ Other Controllers ============================ +//============================================================================= + +// +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 +// +#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define TOUCH_CALIBRATION // Include user calibration widget in menus (Alfawise) + + #if ENABLED(TS_V11) + // Alfawise U20 ILI9341 2.8 TP Ver 1.1 / Green PCB on the back of touchscreen + #define XPT2046_X_CALIBRATION 11605 + #define XPT2046_Y_CALIBRATION 9091 + #define XPT2046_X_OFFSET -24 + #define XPT2046_Y_OFFSET -17 + #endif + + #if ENABLED(TS_V12) + // Alfawise U30 ILI9341 2.8 TP Ver 1.2 / Blue PCB on the back of touchscreen + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 + #endif +#endif + +// +// RepRapWorld REPRAPWORLD_KEYPAD v1.1 +// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626 +// +// REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key +// is pressed, a value of 10.0 means 10mm per click. +// +//#define REPRAPWORLD_KEYPAD +//#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 + +//============================================================================= +//=============================== Extra Features ============================== +//============================================================================= + +// @section extras + +// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino +//#define FAST_PWM_FAN + +// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency +// which is not as annoying as with the hardware PWM. On the other hand, if this frequency +// is too low, you should also increment SOFT_PWM_SCALE. +//#define FAN_SOFT_PWM + +// Incrementing this by 1 will double the software PWM frequency, +// affecting heaters, and the fan if FAN_SOFT_PWM is enabled. +// However, control resolution will be halved for each increment; +// at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] +#define SOFT_PWM_SCALE 0 + +// If SOFT_PWM_SCALE is set to a value higher than 0, dithering can +// be used to mitigate the associated resolution loss. If enabled, +// some of the PWM cycles are stretched so on average the desired +// duty cycle is attained. +//#define SOFT_PWM_DITHER + +// Temperature status LEDs that display the hotend and bed temperature. +// If all hotends, bed temperature, and target temperature are under 54C +// then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis) +//#define TEMP_STAT_LEDS + +// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure +//#define SF_ARC_FIX + +// Support for the BariCUDA Paste Extruder +//#define BARICUDA + +// Support for BlinkM/CyzRgb +//#define BLINKM + +// Support for PCA9632 PWM LED driver +//#define PCA9632 + +// Support for PCA9533 PWM LED driver +// https://github.com/mikeshub/SailfishRGB_LED +//#define PCA9533 + +/** + * RGB LED / LED Strip Control + * + * Enable support for an RGB LED connected to 5V digital pins, or + * an RGB Strip connected to MOSFETs controlled by digital pins. + * + * Adds the M150 command to set the LED (or LED strip) color. + * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of + * luminance values can be set from 0 to 255. + * For Neopixel LED an overall brightness parameter is also available. + * + * *** CAUTION *** + * LED Strips require a MOSFET Chip between PWM lines and LEDs, + * as the Arduino cannot handle the current the LEDs will require. + * Failure to follow this precaution can destroy your Arduino! + * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * more current than the Arduino 5V linear regulator can produce. + * *** CAUTION *** + * + * LED Type. Enable only one of the following two options. + * + */ +//#define RGB_LED +//#define RGBW_LED + +#if EITHER(RGB_LED, RGBW_LED) + //#define RGB_LED_R_PIN 34 + //#define RGB_LED_G_PIN 43 + //#define RGB_LED_B_PIN 35 + //#define RGB_LED_W_PIN -1 +#endif + +// Support for Adafruit Neopixel LED driver +//#define NEOPIXEL_LED +#if ENABLED(NEOPIXEL_LED) + #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. + #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) + //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup + + // Use a single Neopixel LED for static (background) lighting + //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use + //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W +#endif + +/** + * Printer Event LEDs + * + * During printing, the LEDs will reflect the printer status: + * + * - Gradually change from blue to violet as the heated bed gets to target temp + * - Gradually change from violet to red as the hotend gets to temperature + * - Change to white to illuminate work surface + * - Change to green once print has finished + * - Turn off after the print has finished and the user has pushed a button + */ +#if ANY(BLINKM, RGB_LED, RGBW_LED, PCA9632, PCA9533, NEOPIXEL_LED) + #define PRINTER_EVENT_LEDS +#endif + +/** + * R/C SERVO support + * Sponsored by TrinityLabs, Reworked by codexmas + */ + +/** + * Number of servos + * + * For some servo-related options NUM_SERVOS will be set automatically. + * Set this manually if there are extra servos needing manual control. + * Leave undefined or set to 0 to entirely disable the servo subsystem. + */ +//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command + +// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. +// 300ms is a good value but you can try less delay. +// If the servo can't reach the requested position, increase it. +#define SERVO_DELAY { 300 } + +// Only power servos during movement, otherwise leave off to prevent jitter +//#define DEACTIVATE_SERVOS_AFTER_MOVE + +// Allow servo angle to be edited and saved to EEPROM +//#define EDITABLE_SERVO_ANGLES diff --git a/config/examples/Alfawise/U20/Configuration_adv.h b/config/examples/Alfawise/U20/Configuration_adv.h new file mode 100644 index 0000000000..6599509b2c --- /dev/null +++ b/config/examples/Alfawise/U20/Configuration_adv.h @@ -0,0 +1,2564 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Configuration_adv.h + * + * Advanced settings. + * Only change these if you know exactly what you're doing. + * Some of these settings can damage your printer if improperly set! + * + * Basic settings can be found in Configuration.h + * + */ +#define CONFIGURATION_ADV_H_VERSION 020000 + +// @section temperature + +//=========================================================================== +//=============================Thermal Settings ============================ +//=========================================================================== + +// +// Custom Thermistor 1000 parameters +// +#if TEMP_SENSOR_0 == 1000 + #define HOTEND0_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND0_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND0_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_1 == 1000 + #define HOTEND1_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND1_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND1_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_2 == 1000 + #define HOTEND2_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND2_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND2_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_3 == 1000 + #define HOTEND3_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND3_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND3_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_4 == 1000 + #define HOTEND4_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND4_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND4_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_5 == 1000 + #define HOTEND5_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND5_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND5_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_BED == 1000 + #define BED_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define BED_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define BED_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_CHAMBER == 1000 + #define CHAMBER_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define CHAMBER_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define CHAMBER_BETA 3950 // Beta value +#endif + +// +// Hephestos 2 24V heated bed upgrade kit. +// https://store.bq.com/en/heated-bed-kit-hephestos2 +// +//#define HEPHESTOS2_HEATED_BED_KIT +#if ENABLED(HEPHESTOS2_HEATED_BED_KIT) + #undef TEMP_SENSOR_BED + #define TEMP_SENSOR_BED 70 + #define HEATER_BED_INVERTING true +#endif + +/** + * Heated Chamber settings + */ +#if TEMP_SENSOR_CHAMBER + #define CHAMBER_MINTEMP 5 + #define CHAMBER_MAXTEMP 60 + #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target + //#define CHAMBER_LIMIT_SWITCHING + //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin + //#define HEATER_CHAMBER_INVERTING false +#endif + +#if DISABLED(PIDTEMPBED) + #define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control + #if ENABLED(BED_LIMIT_SWITCHING) + #define BED_HYSTERESIS 2 // Only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS + #endif +#endif + +/** + * Thermal Protection provides additional protection to your printer from damage + * and fire. Marlin always includes safe min and max temperature ranges which + * protect against a broken or disconnected thermistor wire. + * + * The issue: If a thermistor falls out, it will report the much lower + * temperature of the air in the room, and the the firmware will keep + * the heater on. + * + * The solution: Once the temperature reaches the target, start observing. + * If the temperature stays too far below the target (hysteresis) for too + * long (period), the firmware will halt the machine as a safety precaution. + * + * If you get false positives for "Thermal Runaway", increase + * THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD + */ +#if ENABLED(THERMAL_PROTECTION_HOTENDS) + #define THERMAL_PROTECTION_PERIOD 60 // Seconds + #define THERMAL_PROTECTION_HYSTERESIS 10 // Degrees Celsius + + //#define ADAPTIVE_FAN_SLOWING // Slow part cooling fan if temperature drops + #if BOTH(ADAPTIVE_FAN_SLOWING, PIDTEMP) + //#define NO_FAN_SLOWING_IN_PID_TUNING // Don't slow fan speed during M303 + #endif + + /** + * Whenever an M104, M109, or M303 increases the target temperature, the + * firmware will wait for the WATCH_TEMP_PERIOD to expire. If the temperature + * hasn't increased by WATCH_TEMP_INCREASE degrees, the machine is halted and + * requires a hard reset. This test restarts with any M104/M109/M303, but only + * if the current temperature is far enough below the target for a reliable + * test. + * + * If you get false positives for "Heating failed", increase WATCH_TEMP_PERIOD + * and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set + * below 2. + */ + #define WATCH_TEMP_PERIOD 60 // Seconds + #define WATCH_TEMP_INCREASE 2 // Degrees Celsius +#endif + +/** + * Thermal Protection parameters for the bed are just as above for hotends. + */ +#if ENABLED(THERMAL_PROTECTION_BED) + #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds + #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius + + /** + * As described above, except for the bed (M140/M190/M303). + */ + #define WATCH_BED_TEMP_PERIOD 60 // Seconds + #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius +#endif + +/** + * Thermal Protection parameters for the heated chamber. + */ +#if ENABLED(THERMAL_PROTECTION_CHAMBER) + #define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds + #define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius + + /** + * Heated chamber watch settings (M141/M191). + */ + #define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds + #define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius +#endif + +#if ENABLED(PIDTEMP) + // Add an experimental additional term to the heater power, proportional to the extrusion speed. + // A well-chosen Kc value should add just enough power to melt the increased material volume. + //#define PID_EXTRUSION_SCALING + #if ENABLED(PID_EXTRUSION_SCALING) + #define DEFAULT_Kc (100) //heating power=Kc*(e_speed) + #define LPQ_MAX_LEN 50 + #endif +#endif + +/** + * Automatic Temperature: + * The hotend target temperature is calculated by all the buffered lines of gcode. + * The maximum buffered steps/sec of the extruder motor is called "se". + * Start autotemp mode with M109 S B F + * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by + * mintemp and maxtemp. Turn this off by executing M109 without F* + * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp. + * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode + */ +#define AUTOTEMP +#if ENABLED(AUTOTEMP) + #define AUTOTEMP_OLDWEIGHT 0.98 +#endif + +// Show extra position information in M114 +//#define M114_DETAIL + +// Show Temperature ADC value +// Enable for M105 to include ADC values read from temperature sensors. +//#define SHOW_TEMP_ADC_VALUES + +/** + * High Temperature Thermistor Support + * + * Thermistors able to support high temperature tend to have a hard time getting + * good readings at room and lower temperatures. This means HEATER_X_RAW_LO_TEMP + * will probably be caught when the heating element first turns on during the + * preheating process, which will trigger a min_temp_error as a safety measure + * and force stop everything. + * To circumvent this limitation, we allow for a preheat time (during which, + * min_temp_error won't be triggered) and add a min_temp buffer to handle + * aberrant readings. + * + * If you want to enable this feature for your hotend thermistor(s) + * uncomment and set values > 0 in the constants below + */ + +// The number of consecutive low temperature errors that can occur +// before a min_temp_error is triggered. (Shouldn't be more than 10.) +//#define MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED 0 + +// The number of milliseconds a hotend will preheat before starting to check +// the temperature. This value should NOT be set to the time it takes the +// hot end to reach the target temperature, but the time it takes to reach +// the minimum temperature your thermistor can read. The lower the better/safer. +// This shouldn't need to be more than 30 seconds (30000) +//#define MILLISECONDS_PREHEAT_TIME 0 + +// @section extruder + +// Extruder runout prevention. +// If the machine is idle and the temperature over MINTEMP +// then extrude some filament every couple of SECONDS. +//#define EXTRUDER_RUNOUT_PREVENT +#if ENABLED(EXTRUDER_RUNOUT_PREVENT) + #define EXTRUDER_RUNOUT_MINTEMP 190 + #define EXTRUDER_RUNOUT_SECONDS 30 + #define EXTRUDER_RUNOUT_SPEED 1500 // (mm/m) + #define EXTRUDER_RUNOUT_EXTRUDE 5 // (mm) +#endif + +// @section temperature + +// Calibration for AD595 / AD8495 sensor to adjust temperature measurements. +// The final temperature is calculated as (measuredTemp * GAIN) + OFFSET. +#define TEMP_SENSOR_AD595_OFFSET 0.0 +#define TEMP_SENSOR_AD595_GAIN 1.0 +#define TEMP_SENSOR_AD8495_OFFSET 0.0 +#define TEMP_SENSOR_AD8495_GAIN 1.0 + +/** + * Controller Fan + * To cool down the stepper drivers and MOSFETs. + * + * The fan will turn on automatically whenever any stepper is enabled + * and turn off after a set period after all steppers are turned off. + */ +//#define USE_CONTROLLER_FAN +#if ENABLED(USE_CONTROLLER_FAN) + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled + #define CONTROLLERFAN_SPEED 255 // 255 == full speed +#endif + +// When first starting the main fan, run it at full speed for the +// given number of milliseconds. This gets the fan spinning reliably +// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) +//#define FAN_KICKSTART_TIME 100 + +/** + * PWM Fan Scaling + * + * Define the min/max speeds for PWM fans (as set with M106). + * + * With these options the M106 0-255 value range is scaled to a subset + * to ensure that the fan has enough power to spin, or to run lower + * current fans with higher current. (e.g., 5V/12V fans with 12V/24V) + * Value 0 always turns off the fan. + * + * Define one or both of these to override the default 0-255 range. + */ +//#define FAN_MIN_PWM 50 +//#define FAN_MAX_PWM 128 + +/** + * FAST PWM FAN Settings + * + * Use to change the FAST FAN PWM frequency (if enabled in Configuration.h) + * Combinations of PWM Modes, prescale values and TOP resolutions are used internally to produce a + * frequency as close as possible to the desired frequency. + * + * FAST_PWM_FAN_FREQUENCY [undefined by default] + * Set this to your desired frequency. + * If left undefined this defaults to F = F_CPU/(2*255*1) + * ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers + * These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required + * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior. + * + * USE_OCR2A_AS_TOP [undefined by default] + * Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2: + * 16MHz MCUs: [62.5KHz, 31.4KHz (default), 7.8KHz, 3.92KHz, 1.95KHz, 977Hz, 488Hz, 244Hz, 60Hz, 122Hz, 30Hz] + * 20MHz MCUs: [78.1KHz, 39.2KHz (default), 9.77KHz, 4.9KHz, 2.44KHz, 1.22KHz, 610Hz, 305Hz, 153Hz, 76Hz, 38Hz] + * A greater range can be achieved by enabling USE_OCR2A_AS_TOP. But note that this option blocks the use of + * PWM on pin OC2A. Only use this option if you don't need PWM on 0C2A. (Check your schematic.) + * USE_OCR2A_AS_TOP sacrifices duty cycle control resolution to achieve this broader range of frequencies. + */ +#if ENABLED(FAST_PWM_FAN) + //#define FAST_PWM_FAN_FREQUENCY 31400 + //#define USE_OCR2A_AS_TOP +#endif + +// @section extruder + +/** + * Extruder cooling fans + * + * Extruder auto fans automatically turn on when their extruders' + * temperatures go above EXTRUDER_AUTO_FAN_TEMPERATURE. + * + * Your board's pins file specifies the recommended pins. Override those here + * or set to -1 to disable completely. + * + * Multiple extruders can be assigned to the same pin in which case + * the fan will turn on when any selected extruder is above the threshold. + */ +#define E0_AUTO_FAN_PIN -1 +#define E1_AUTO_FAN_PIN -1 +#define E2_AUTO_FAN_PIN -1 +#define E3_AUTO_FAN_PIN -1 +#define E4_AUTO_FAN_PIN -1 +#define E5_AUTO_FAN_PIN -1 +#define CHAMBER_AUTO_FAN_PIN -1 + +#define EXTRUDER_AUTO_FAN_TEMPERATURE 50 +#define EXTRUDER_AUTO_FAN_SPEED 255 // 255 == full speed +#define CHAMBER_AUTO_FAN_TEMPERATURE 30 +#define CHAMBER_AUTO_FAN_SPEED 255 + +/** + * Part-Cooling Fan Multiplexer + * + * This feature allows you to digitally multiplex the fan output. + * The multiplexer is automatically switched at tool-change. + * Set FANMUX[012]_PINs below for up to 2, 4, or 8 multiplexed fans. + */ +#define FANMUX0_PIN -1 +#define FANMUX1_PIN -1 +#define FANMUX2_PIN -1 + +/** + * M355 Case Light on-off / brightness + */ +//#define CASE_LIGHT_ENABLE +#if ENABLED(CASE_LIGHT_ENABLE) + //#define CASE_LIGHT_PIN 4 // Override the default pin if needed + #define INVERT_CASE_LIGHT false // Set true if Case Light is ON when pin is LOW + #define CASE_LIGHT_DEFAULT_ON true // Set default power-up state on + #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105 // Set default power-up brightness (0-255, requires PWM pin) + //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu + //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. + //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) + #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } + #endif +#endif + +// @section homing + +// If you want endstops to stay on (by default) even when not homing +// enable this option. Override at any time with M120, M121. +//#define ENDSTOPS_ALWAYS_ON_DEFAULT + +// @section extras + +//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats. + +// Employ an external closed loop controller. Override pins here if needed. +//#define EXTERNAL_CLOSED_LOOP_CONTROLLER +#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER) + //#define CLOSED_LOOP_ENABLE_PIN -1 + //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1 +#endif + +/** + * Dual Steppers / Dual Endstops + * + * This section will allow you to use extra E drivers to drive a second motor for X, Y, or Z axes. + * + * For example, set X_DUAL_STEPPER_DRIVERS setting to use a second motor. If the motors need to + * spin in opposite directions set INVERT_X2_VS_X_DIR. If the second motor needs its own endstop + * set X_DUAL_ENDSTOPS. This can adjust for "racking." Use X2_USE_ENDSTOP to set the endstop plug + * that should be used for the second endstop. Extra endstops will appear in the output of 'M119'. + * + * Use X_DUAL_ENDSTOP_ADJUSTMENT to adjust for mechanical imperfection. After homing both motors + * this offset is applied to the X2 motor. To find the offset home the X axis, and measure the error + * in X2. Dual endstop offsets can be set at runtime with 'M666 X Y Z'. + */ + +//#define X_DUAL_STEPPER_DRIVERS +#if ENABLED(X_DUAL_STEPPER_DRIVERS) + #define INVERT_X2_VS_X_DIR true // Set 'true' if X motors should rotate in opposite directions + //#define X_DUAL_ENDSTOPS + #if ENABLED(X_DUAL_ENDSTOPS) + #define X2_USE_ENDSTOP _XMAX_ + #define X_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Y_DUAL_STEPPER_DRIVERS +#if ENABLED(Y_DUAL_STEPPER_DRIVERS) + #define INVERT_Y2_VS_Y_DIR true // Set 'true' if Y motors should rotate in opposite directions + //#define Y_DUAL_ENDSTOPS + #if ENABLED(Y_DUAL_ENDSTOPS) + #define Y2_USE_ENDSTOP _YMAX_ + #define Y_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Z_DUAL_STEPPER_DRIVERS +#if ENABLED(Z_DUAL_STEPPER_DRIVERS) + //#define Z_DUAL_ENDSTOPS + #if ENABLED(Z_DUAL_ENDSTOPS) + #define Z2_USE_ENDSTOP _XMAX_ + #define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Z_TRIPLE_STEPPER_DRIVERS +#if ENABLED(Z_TRIPLE_STEPPER_DRIVERS) + //#define Z_TRIPLE_ENDSTOPS + #if ENABLED(Z_TRIPLE_ENDSTOPS) + #define Z2_USE_ENDSTOP _XMAX_ + #define Z3_USE_ENDSTOP _YMAX_ + #define Z_TRIPLE_ENDSTOPS_ADJUSTMENT2 0 + #define Z_TRIPLE_ENDSTOPS_ADJUSTMENT3 0 + #endif +#endif + +/** + * Dual X Carriage + * + * This setup has two X carriages that can move independently, each with its own hotend. + * The carriages can be used to print an object with two colors or materials, or in + * "duplication mode" it can print two identical or X-mirrored objects simultaneously. + * The inactive carriage is parked automatically to prevent oozing. + * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. + * By default the X2 stepper is assigned to the first unused E plug on the board. + * + * The following Dual X Carriage modes can be selected with M605 S: + * + * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel + * results as long as it supports dual X-carriages. (M605 S0) + * + * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so + * that additional slicer support is not required. (M605 S1) + * + * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with + * the first X-carriage and extruder, to print 2 copies of the same object at the same time. + * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and + * follow with M605 S2 to initiate duplicated movement. + * + * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates + * the movement of the first except the second extruder is reversed in the X axis. + * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and + * follow with M605 S3 to initiate mirrored movement. + */ +//#define DUAL_X_CARRIAGE +#if ENABLED(DUAL_X_CARRIAGE) + #define X1_MIN_POS X_MIN_POS // Set to X_MIN_POS + #define X1_MAX_POS X_BED_SIZE // Set a maximum so the first X-carriage can't hit the parked second X-carriage + #define X2_MIN_POS 80 // Set a minimum to ensure the second X-carriage can't hit the parked first X-carriage + #define X2_MAX_POS 353 // Set this to the distance between toolheads when both heads are homed + #define X2_HOME_DIR 1 // Set to 1. The second X-carriage always homes to the maximum endstop position + #define X2_HOME_POS X2_MAX_POS // Default X2 home position. Set to X2_MAX_POS. + // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software + // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops + // without modifying the firmware (through the "M218 T1 X???" command). + // Remember: you should set the second extruder x-offset to 0 in your slicer. + + // This is the default power-up mode which can be later using M605. + #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_AUTO_PARK_MODE + + // Default x offset in duplication mode (typically set to half print bed width) + #define DEFAULT_DUPLICATION_X_OFFSET 100 + +#endif // DUAL_X_CARRIAGE + +// Activate a solenoid on the active extruder with M380. Disable all with M381. +// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid. +//#define EXT_SOLENOID + +// @section homing + +// Homing hits each endstop, retracts by these distances, then does a slower bump. +#define X_HOME_BUMP_MM 5 +#define Y_HOME_BUMP_MM 5 +#define Z_HOME_BUMP_MM 2 +#define HOMING_BUMP_DIVISOR { 2, 2, 4 } // Re-Bump Speed Divisor (Divides the Homing Feedrate) +//#define QUICK_HOME // If homing includes X and Y, do a diagonal move initially +//#define HOMING_BACKOFF_MM { 2, 2, 2 } // (mm) Move away from the endstops after homing + +// When G28 is called, this option will make Y home before X +//#define HOME_Y_BEFORE_X + +// Enable this if X or Y can't home without homing the other axis first. +//#define CODEPENDENT_XY_HOMING + +#if ENABLED(BLTOUCH) + /** + * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES + * Do not activate settings that the probe might not understand. Clones might misunderstand + * advanced commands. + * + * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then + * check the wiring of the BROWN, RED and ORANGE wires. + * + * Note: If the trigger signal of your probe is not being recognized, it has been very often + * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable" + * like they would be with a real switch. So please check the wiring first. + * + * Settings for all BLTouch and clone probes: + */ + + // Safety: The probe needs time to recognize the command. + // Minimum command delay (ms). Enable and increase if needed. + //#define BLTOUCH_DELAY 500 + + /** + * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones: + */ + + // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful + // in special cases, like noisy or filtered input configurations. + //#define BLTOUCH_FORCE_SW_MODE + + /** + * Settings for BLTouch Smart 3.0 and 3.1 + * Summary: + * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes + * - High-Speed mode + * - Disable LCD voltage options + */ + + /** + * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller! + * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup. + * If disabled, OD mode is the hard-coded default on 3.0 + * On startup, Marlin will compare its eeprom to this vale. If the selected mode + * differs, a mode set eeprom write will be completed at initialization. + * Use the option below to force an eeprom write to a V3.1 probe regardless. + */ + //#define BLTOUCH_SET_5V_MODE + + /** + * Safety: Activate if connecting a probe with an unknown voltage mode. + * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0 + * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write ) + * To preserve the life of the probe, use this once then turn it off and re-flash. + */ + //#define BLTOUCH_FORCE_MODE_SET + + /** + * Use "HIGH SPEED" mode for probing. + * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems. + * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function + * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state. + */ + //#define BLTOUCH_HS_MODE + + // Safety: Enable voltage mode settings in the LCD menu. + //#define BLTOUCH_LCD_VOLTAGE_MENU + +#endif // BLTOUCH + +/** + * Z Steppers Auto-Alignment + * Add the G34 command to align multiple Z steppers using a bed probe. + */ +//#define Z_STEPPER_AUTO_ALIGN +#if ENABLED(Z_STEPPER_AUTO_ALIGN) + // Define probe X and Y positions for Z1, Z2 [, Z3] + #define Z_STEPPER_ALIGN_X { 10, 150, 290 } + #define Z_STEPPER_ALIGN_Y { 290, 10, 290 } + // Set number of iterations to align + #define Z_STEPPER_ALIGN_ITERATIONS 3 + // Enable to restore leveling setup after operation + #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + + // Use the amplification factor to de-/increase correction step. + // In case the stepper (spindle) position is further out than the test point + // Use a value > 1. NOTE: This may cause instability + #define Z_STEPPER_ALIGN_AMP 1.0 + // Stop criterion. If the accuracy is better than this stop iterating early + #define Z_STEPPER_ALIGN_ACC 0.02 +#endif + +// @section machine + +#define AXIS_RELATIVE_MODES { false, false, false, false } + +// Add a Duplicate option for well-separated conjoined nozzles +//#define MULTI_NOZZLE_DUPLICATION + +// By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step. +#define INVERT_X_STEP_PIN false +#define INVERT_Y_STEP_PIN false +#define INVERT_Z_STEP_PIN false +#define INVERT_E_STEP_PIN false + +// Default stepper release if idle. Set to 0 to deactivate. +// Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true. +// Time can be set by M18 and M84. +#define DEFAULT_STEPPER_DEACTIVE_TIME 120 +#define DISABLE_INACTIVE_X true +#define DISABLE_INACTIVE_Y true +#define DISABLE_INACTIVE_Z true // Set to false if the nozzle will fall down on your printed part when print has finished. +#define DISABLE_INACTIVE_E true + +#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate +#define DEFAULT_MINTRAVELFEEDRATE 0.0 + +//#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated + +// @section lcd + +#if EITHER(ULTIPANEL, EXTENSIBLE_UI) + #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #if ENABLED(ULTIPANEL) + #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" + #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen + #endif +#endif + +// @section extras + +// minimum time in microseconds that a movement needs to take if the buffer is emptied. +#define DEFAULT_MINSEGMENTTIME 20000 + +// If defined the movements slow down when the look ahead buffer is only half full +#define SLOWDOWN + +// Frequency limit +// See nophead's blog for more info +// Not working O +//#define XY_FREQUENCY_LIMIT 15 + +// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end +// of the buffer and all stops. This should not be much greater than zero and should only be changed +// if unwanted behavior is observed on a user's machine when running at very slow speeds. +#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s) + +// +// Backlash Compensation +// Adds extra movement to axes on direction-changes to account for backlash. +// +//#define BACKLASH_COMPENSATION +#if ENABLED(BACKLASH_COMPENSATION) + // Define values for backlash distance and correction. + // If BACKLASH_GCODE is enabled these values are the defaults. + #define BACKLASH_DISTANCE_MM { 0, 0, 0 } // (mm) + #define BACKLASH_CORRECTION 0.0 // 0.0 = no correction; 1.0 = full correction + + // Set BACKLASH_SMOOTHING_MM to spread backlash correction over multiple segments + // to reduce print artifacts. (Enabling this is costly in memory and computation!) + //#define BACKLASH_SMOOTHING_MM 3 // (mm) + + // Add runtime configuration and tuning of backlash values (M425) + //#define BACKLASH_GCODE + + #if ENABLED(BACKLASH_GCODE) + // Measure the Z backlash when probing (G29) and set with "M425 Z" + #define MEASURE_BACKLASH_WHEN_PROBING + + #if ENABLED(MEASURE_BACKLASH_WHEN_PROBING) + // When measuring, the probe will move up to BACKLASH_MEASUREMENT_LIMIT + // mm away from point of contact in BACKLASH_MEASUREMENT_RESOLUTION + // increments while checking for the contact to be broken. + #define BACKLASH_MEASUREMENT_LIMIT 0.5 // (mm) + #define BACKLASH_MEASUREMENT_RESOLUTION 0.005 // (mm) + #define BACKLASH_MEASUREMENT_FEEDRATE Z_PROBE_SPEED_SLOW // (mm/m) + #endif + #endif +#endif + +/** + * Automatic backlash, position and hotend offset calibration + * + * Enable G425 to run automatic calibration using an electrically- + * conductive cube, bolt, or washer mounted on the bed. + * + * G425 uses the probe to touch the top and sides of the calibration object + * on the bed and measures and/or correct positional offsets, axis backlash + * and hotend offsets. + * + * Note: HOTEND_OFFSET and CALIBRATION_OBJECT_CENTER must be set to within + * ±5mm of true values for G425 to succeed. + */ +//#define CALIBRATION_GCODE +#if ENABLED(CALIBRATION_GCODE) + + #define CALIBRATION_MEASUREMENT_RESOLUTION 0.01 // mm + + #define CALIBRATION_FEEDRATE_SLOW 60 // mm/m + #define CALIBRATION_FEEDRATE_FAST 1200 // mm/m + #define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/m + + // The following parameters refer to the conical section of the nozzle tip. + #define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm + #define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm + + // Uncomment to enable reporting (required for "G425 V", but consumes PROGMEM). + //#define CALIBRATION_REPORTING + + // The true location and dimension the cube/bolt/washer on the bed. + #define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0} // mm + #define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0} // mm + + // Comment out any sides which are unreachable by the probe. For best + // auto-calibration results, all sides must be reachable. + #define CALIBRATION_MEASURE_RIGHT + #define CALIBRATION_MEASURE_FRONT + #define CALIBRATION_MEASURE_LEFT + #define CALIBRATION_MEASURE_BACK + + // Probing at the exact top center only works if the center is flat. If + // probing on a screwhead or hollow washer, probe near the edges. + //#define CALIBRATION_MEASURE_AT_TOP_EDGES + + // Define pin which is read during calibration + #ifndef CALIBRATION_PIN + #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop + #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin + //#define CALIBRATION_PIN_PULLDOWN + #define CALIBRATION_PIN_PULLUP + #endif +#endif + +/** + * Adaptive Step Smoothing increases the resolution of multi-axis moves, particularly at step frequencies + * below 1kHz (for AVR) or 10kHz (for ARM), where aliasing between axes in multi-axis moves causes audible + * vibration and surface artifacts. The algorithm adapts to provide the best possible step smoothing at the + * lowest stepping frequencies. + */ +//#define ADAPTIVE_STEP_SMOOTHING + +/** + * Custom Microstepping + * Override as-needed for your setup. Up to 3 MS pins are supported. + */ +//#define MICROSTEP1 LOW,LOW,LOW +//#define MICROSTEP2 HIGH,LOW,LOW +//#define MICROSTEP4 LOW,HIGH,LOW +//#define MICROSTEP8 HIGH,HIGH,LOW +//#define MICROSTEP16 LOW,LOW,HIGH +//#define MICROSTEP32 HIGH,LOW,HIGH + +// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU. +#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16] + +/** + * @section stepper motor current + * + * Some boards have a means of setting the stepper motor current via firmware. + * + * The power on motor currents are set by: + * PWM_MOTOR_CURRENT - used by MINIRAMBO & ULTIMAIN_2 + * known compatible chips: A4982 + * DIGIPOT_MOTOR_CURRENT - used by BQ_ZUM_MEGA_3D, RAMBO & SCOOVO_X9H + * known compatible chips: AD5206 + * DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2 + * known compatible chips: MCP4728 + * DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, AZTEEG_X5_MINI_WIFI, MIGHTYBOARD_REVE + * known compatible chips: MCP4451, MCP4018 + * + * Motor currents can also be set by M907 - M910 and by the LCD. + * M907 - applies to all. + * M908 - BQ_ZUM_MEGA_3D, RAMBO, PRINTRBOARD_REVF, RIGIDBOARD_V2 & SCOOVO_X9H + * M909, M910 & LCD - only PRINTRBOARD_REVF & RIGIDBOARD_V2 + */ +//#define PWM_MOTOR_CURRENT { 1300, 1300, 1250 } // Values in milliamps +//#define DIGIPOT_MOTOR_CURRENT { 135,135,135,135,135 } // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A) +//#define DAC_MOTOR_CURRENT_DEFAULT { 70, 80, 90, 80 } // Default drive percent - X, Y, Z, E axis + +// Use an I2C based DIGIPOT (e.g., Azteeg X3 Pro) +//#define DIGIPOT_I2C +#if ENABLED(DIGIPOT_I2C) && !defined(DIGIPOT_I2C_ADDRESS_A) + /** + * Common slave addresses: + * + * A (A shifted) B (B shifted) IC + * Smoothie 0x2C (0x58) 0x2D (0x5A) MCP4451 + * AZTEEG_X3_PRO 0x2C (0x58) 0x2E (0x5C) MCP4451 + * AZTEEG_X5_MINI 0x2C (0x58) 0x2E (0x5C) MCP4451 + * AZTEEG_X5_MINI_WIFI 0x58 0x5C MCP4451 + * MIGHTYBOARD_REVE 0x2F (0x5E) MCP4018 + */ + #define DIGIPOT_I2C_ADDRESS_A 0x2C // unshifted slave address for first DIGIPOT + #define DIGIPOT_I2C_ADDRESS_B 0x2D // unshifted slave address for second DIGIPOT +#endif + +//#define DIGIPOT_MCP4018 // Requires library from https://github.com/stawel/SlowSoftI2CMaster +#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8 MKS SBASE: 5 +// Actual motor currents in Amps. The number of entries must match DIGIPOT_I2C_NUM_CHANNELS. +// These correspond to the physical drivers, so be mindful if the order is changed. +#define DIGIPOT_I2C_MOTOR_CURRENTS { 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0 } // AZTEEG_X3_PRO + +//=========================================================================== +//=============================Additional Features=========================== +//=========================================================================== + +// @section lcd + +// Change values more rapidly when the encoder is rotated faster +#define ENCODER_RATE_MULTIPLIER +#if ENABLED(ENCODER_RATE_MULTIPLIER) + #define ENCODER_10X_STEPS_PER_SEC 30 // (steps/s) Encoder rate for 10x speed + #define ENCODER_100X_STEPS_PER_SEC 80 // (steps/s) Encoder rate for 100x speed +#endif + +// Play a beep when the feedrate is changed from the Status Screen +//#define BEEP_ON_FEEDRATE_CHANGE +#if ENABLED(BEEP_ON_FEEDRATE_CHANGE) + #define FEEDRATE_CHANGE_BEEP_DURATION 10 + #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 +#endif + +// Include a page of printer information in the LCD Main Menu +#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif + +// Scroll a longer status message into view +//#define STATUS_MESSAGE_SCROLLING + +// On the Info Screen, display XY with one decimal place when possible +//#define LCD_DECIMAL_SMALL_XY + +// The timeout (in ms) to return to the status screen from sub-menus +//#define LCD_TIMEOUT_TO_STATUS 15000 + +// Add an 'M73' G-code to set the current percentage +#define LCD_SET_PROGRESS_MANUALLY + +#if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS + //#define LCD_PROGRESS_BAR // Show a progress bar on HD44780 LCDs for SD printing + #if ENABLED(LCD_PROGRESS_BAR) + #define PROGRESS_BAR_BAR_TIME 2000 // (ms) Amount of time to show the bar + #define PROGRESS_BAR_MSG_TIME 3000 // (ms) Amount of time to show the status message + #define PROGRESS_MSG_EXPIRE 0 // (ms) Amount of time to retain the status message (0=forever) + //#define PROGRESS_MSG_ONCE // Show the message for MSG_TIME then clear it + //#define LCD_PROGRESS_BAR_TEST // Add a menu item to test the progress bar + #endif +#endif + +/** + * LED Control Menu + * Enable this feature to add LED Control to the LCD menu + */ +//#define LED_CONTROL_MENU +#if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif +#endif // LED_CONTROL_MENU + +#if ENABLED(SDSUPPORT) + + // Some RAMPS and other boards don't detect when an SD card is inserted. You can work + // around this by connecting a push button or single throw switch to the pin defined + // as SD_DETECT_PIN in your board's pins definitions. + // This setting should be disabled unless you are using a push button, pulling the pin to ground. + // Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER). + #define SD_DETECT_INVERTED + + #define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished + #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place. + + // Reverse SD sort to show "more recent" files first, according to the card's FAT. + // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended. + #define SDCARD_RATHERRECENTFIRST + + #define SD_MENU_CONFIRM_START // Confirm the selected SD file before printing + + #define MENU_ADDAUTOSTART // Add a menu option to run auto#.g files + + #define EVENT_GCODE_SD_STOP "G28XY" // G-code to run on Stop Print (e.g., "G28XY" or "G27") + + /** + * Continue after Power-Loss (Creality3D) + * + * Store the current state to the SD Card at the start of each layer + * during SD printing. If the recovery file is found at boot time, present + * an option on the LCD screen to continue the print from the last-known + * point in the file. + */ + #define POWER_LOSS_RECOVERY + #if ENABLED(POWER_LOSS_RECOVERY) + //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume + //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. + + // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, + // especially with "vase mode" printing. Set too high and vases cannot be continued. + #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + + //#define DEBUG_POWER_LOSS_RECOVERY // Debug informations on serial output + //#define SAVE_INFO_INTERVAL_MS 0 // Force SD recov. write interval, on each layer start if 0 + #endif + + /** + * Sort SD file listings in alphabetical order. + * + * With this option enabled, items on SD cards will be sorted + * by name for easier navigation. + * + * By default... + * + * - Use the slowest -but safest- method for sorting. + * - Folders are sorted to the top. + * - The sort key is statically allocated. + * - No added G-code (M34) support. + * - 40 item sorting limit. (Items after the first 40 are unsorted.) + * + * SD sorting uses static allocation (as set by SDSORT_LIMIT), allowing the + * compiler to calculate the worst-case usage and throw an error if the SRAM + * limit is exceeded. + * + * - SDSORT_USES_RAM provides faster sorting via a static directory buffer. + * - SDSORT_USES_STACK does the same, but uses a local stack-based buffer. + * - SDSORT_CACHE_NAMES will retain the sorted file listing in RAM. (Expensive!) + * - SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible. (Use with caution!) + */ + #define SDCARD_SORT_ALPHA + + // SD Card Sorting options + #if ENABLED(SDCARD_SORT_ALPHA) + #define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). Costs 27 bytes each. + #define FOLDER_SORTING -1 // -1=above 0=none 1=below + #define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 g-code. + #define SDSORT_USES_RAM false // Pre-allocate a static array for faster pre-sorting. + #define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.) + #define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option. + #define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use! + #define SDSORT_CACHE_VFATS 2 // Maximum number of 13-byte VFAT entries to use for sorting. + // Note: Only affects SCROLL_LONG_FILENAMES with SDSORT_CACHE_NAMES but not SDSORT_DYNAMIC_RAM. + #endif + + // This allows hosts to request long names for files and folders with M33 + #define LONG_FILENAME_HOST_SUPPORT + + // Enable this option to scroll long filenames in the SD card menu + //#define SCROLL_LONG_FILENAMES + + // Leave the heaters on after Stop Print (not recommended!) + //#define SD_ABORT_NO_COOLDOWN + + /** + * This option allows you to abort SD printing when any endstop is triggered. + * This feature must be enabled with "M540 S1" or from the LCD menu. + * To have any effect, endstops must be enabled during SD printing. + */ + //#define SD_ABORT_ON_ENDSTOP_HIT + + /** + * This option makes it easier to print the same SD Card file again. + * On print completion the LCD Menu will open with the file selected. + * You can just click to start the print, or navigate elsewhere. + */ + #define SD_REPRINT_LAST_SELECTED_FILE + + /** + * Auto-report SdCard status with M27 S + */ + //#define AUTO_REPORT_SD_STATUS + + /** + * Support for USB thumb drives using an Arduino USB Host Shield or + * equivalent MAX3421E breakout board. The USB thumb drive will appear + * to Marlin as an SD card. + * + * The MAX3421E must be assigned the same pins as the SD card reader, with + * the following pin mapping: + * + * SCLK, MOSI, MISO --> SCLK, MOSI, MISO + * INT --> SD_DETECT_PIN + * SS --> SDSS + */ + //#define USB_FLASH_DRIVE_SUPPORT + #if ENABLED(USB_FLASH_DRIVE_SUPPORT) + #define USB_CS_PIN SDSS + #define USB_INTR_PIN SD_DETECT_PIN + #endif + + /** + * When using a bootloader that supports SD-Firmware-Flashing, + * add a menu item to activate SD-FW-Update on the next reboot. + * + * Requires ATMEGA2560 (Arduino Mega) + * + * Tested with this bootloader: + * https://github.com/FleetProbe/MicroBridge-Arduino-ATMega2560 + */ + //#define SD_FIRMWARE_UPDATE + #if ENABLED(SD_FIRMWARE_UPDATE) + #define SD_FIRMWARE_UPDATE_EEPROM_ADDR 0x1FF + #define SD_FIRMWARE_UPDATE_ACTIVE_VALUE 0xF0 + #define SD_FIRMWARE_UPDATE_INACTIVE_VALUE 0xFF + #endif + + // Add an optimized binary file transfer mode, initiated with 'M28 B1' + //#define BINARY_FILE_TRANSFER + + #if HAS_SDCARD_CONNECTION + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD + #endif + +#endif // SDSUPPORT + +/** + * By default an onboard SD card reader may be shared as a USB mass- + * storage device. This option hides the SD card from the host PC. + */ +//#define NO_SD_HOST_DRIVE // Disable SD Card access over USB (for security). + +/** + * Additional options for Graphical Displays + * + * Use the optimizations here to improve printing performance, + * which can be adversely affected by graphical display drawing, + * especially when doing several short moves, and when printing + * on DELTA and SCARA machines. + * + * Some of these options may result in the display lagging behind + * controller events, as there is a trade-off between reliable + * printing performance versus fast display updates. + */ +#if HAS_GRAPHICAL_LCD + // Show SD percentage next to the progress bar + #define DOGM_SD_PERCENT + + // Enable to save many cycles by drawing a hollow frame on the Info Screen + #define XYZ_HOLLOW_FRAME + + // Enable to save many cycles by drawing a hollow frame on Menu Screens + #define MENU_HOLLOW_FRAME + + // A bigger font is available for edit items. Costs 3120 bytes of PROGMEM. + // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. + //#define USE_BIG_EDIT_FONT + + // A smaller font may be used on the Info Screen. Costs 2300 bytes of PROGMEM. + // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. + //#define USE_SMALL_INFOFONT + + // Enable this option and reduce the value to optimize screen updates. + // The normal delay is 10µs. Use the lowest value that still gives a reliable display. + //#define DOGM_SPI_DELAY_US 5 + + // Swap the CW/CCW indicators in the graphics overlay + //#define OVERLAY_GFX_REVERSE + + /** + * ST7920-based LCDs can emulate a 16 x 4 character display using + * the ST7920 character-generator for very fast screen updates. + * Enable LIGHTWEIGHT_UI to use this special display mode. + * + * Since LIGHTWEIGHT_UI has limited space, the position and status + * message occupy the same line. Set STATUS_EXPIRE_SECONDS to the + * length of time to display the status message before clearing. + * + * Set STATUS_EXPIRE_SECONDS to zero to never clear the status. + * This will prevent position updates from being displayed. + */ + #if ENABLED(U8GLIB_ST7920) + //#define LIGHTWEIGHT_UI + #if ENABLED(LIGHTWEIGHT_UI) + #define STATUS_EXPIRE_SECONDS 20 + #endif + #endif + + /** + * Status (Info) Screen customizations + * These options may affect code size and screen render time. + * Custom status screens can forcibly override these settings. + */ + //#define STATUS_COMBINE_HEATERS // Use combined heater images instead of separate ones + //#define STATUS_HOTEND_NUMBERLESS // Use plain hotend icons instead of numbered ones (with 2+ hotends) + #define STATUS_HOTEND_INVERTED // Show solid nozzle bitmaps when heating (Requires STATUS_HOTEND_ANIM) + #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating + #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating + #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap + //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap + //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames + #define STATUS_HEAT_PERCENT // Show heating in a progress bar + //#define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash) + + // Frivolous Game Options + //#define MARLIN_BRICKOUT + //#define MARLIN_INVADERS + //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu + +#endif // HAS_GRAPHICAL_LCD + +// @section safety + +/** + * The watchdog hardware timer will do a reset and disable all outputs + * if the firmware gets too overloaded to read the temperature sensors. + * + * If you find that watchdog reboot causes your AVR board to hang forever, + * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO. + * NOTE: This method is less reliable as it can only catch hangups while + * interrupts are enabled. + */ +#define USE_WATCHDOG +#if ENABLED(USE_WATCHDOG) + //#define WATCHDOG_RESET_MANUAL +#endif + +// @section lcd + +/** + * Babystepping enables movement of the axes by tiny increments without changing + * the current position values. This feature is used primarily to adjust the Z + * axis in the first layer of a print in real-time. + * + * Warning: Does not respect endstops! + */ +//#define BABYSTEPPING +#if ENABLED(BABYSTEPPING) + //#define BABYSTEP_WITHOUT_HOMING + //#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA! + #define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way + #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion. + + //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping. + #if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING) + #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds. + // Note: Extra time may be added to mitigate controller latency. + //#define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement). + //#define MOVE_Z_WHEN_IDLE // Jump to the move Z menu on doubleclick when printer is idle. + #if ENABLED(MOVE_Z_WHEN_IDLE) + #define MOVE_Z_IDLE_MULTIPLICATOR 1 // Multiply 1mm by this factor for the move step size. + #endif + #endif + + //#define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28 + + //#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping + #if ENABLED(BABYSTEP_ZPROBE_OFFSET) + //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets + //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor + #endif +#endif + +// @section extruder + +/** + * Linear Pressure Control v1.5 + * + * Assumption: advance [steps] = k * (delta velocity [steps/s]) + * K=0 means advance disabled. + * + * NOTE: K values for LIN_ADVANCE 1.5 differ from earlier versions! + * + * Set K around 0.22 for 3mm PLA Direct Drive with ~6.5cm between the drive gear and heatbreak. + * Larger K values will be needed for flexible filament and greater distances. + * If this algorithm produces a higher speed offset than the extruder can handle (compared to E jerk) + * print acceleration will be reduced during the affected moves to keep within the limit. + * + * See http://marlinfw.org/docs/features/lin_advance.html for full instructions. + * Mention @Sebastianv650 on GitHub to alert the author of any issues. + */ +//#define LIN_ADVANCE +#if ENABLED(LIN_ADVANCE) + //#define EXTRA_LIN_ADVANCE_K // Enable for second linear advance constants + #define LIN_ADVANCE_K 0.22 // Unit: mm compression per 1mm/s extruder speed + //#define LA_DEBUG // If enabled, this will generate debug information output over USB. +#endif + +// @section leveling + +#if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL) + // Override the mesh area if the automatic (max) area is too large + //#define MESH_MIN_X MESH_INSET + //#define MESH_MIN_Y MESH_INSET + //#define MESH_MAX_X X_BED_SIZE - (MESH_INSET) + //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET) +#endif + +/** + * Repeatedly attempt G29 leveling until it succeeds. + * Stop after G29_MAX_RETRIES attempts. + */ +//#define G29_RETRY_AND_RECOVER +#if ENABLED(G29_RETRY_AND_RECOVER) + #define G29_MAX_RETRIES 3 + #define G29_HALT_ON_FAILURE + /** + * Specify the GCODE commands that will be executed when leveling succeeds, + * between attempts, and after the maximum number of retries have been tried. + */ + #define G29_SUCCESS_COMMANDS "M117 Bed leveling done." + #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0" + #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1" + +#endif + +// @section extras + +// +// G2/G3 Arc Support +// +#define ARC_SUPPORT // Disable this feature to save ~3226 bytes +#if ENABLED(ARC_SUPPORT) + #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles + //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes +#endif + +// Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes. +//#define BEZIER_CURVE_SUPPORT + +/** + * G38 Probe Target + * + * This option adds G38.2 and G38.3 (probe towards target) + * and optionally G38.4 and G38.5 (probe away from target). + * Set MULTIPLE_PROBING for G38 to probe more than once. + */ +//#define G38_PROBE_TARGET +#if ENABLED(G38_PROBE_TARGET) + //#define G38_PROBE_AWAY // Include G38.4 and G38.5 to probe away from target + #define G38_MINIMUM_MOVE 0.0275 // (mm) Minimum distance that will produce a move. +#endif + +// Moves (or segments) with fewer steps than this will be joined with the next move +#define MIN_STEPS_PER_SEGMENT 6 + +/** + * Minimum delay after setting the stepper DIR (in ns) + * 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire) + * 20 : Minimum for TMC2xxx drivers + * 200 : Minimum for A4988 drivers + * 400 : Minimum for A5984 drivers + * 500 : Minimum for LV8729 drivers (guess, no info in datasheet) + * 650 : Minimum for DRV8825 drivers + * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet) + * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet) + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MINIMUM_STEPPER_DIR_DELAY 650 + +/** + * Minimum stepper driver pulse width (in µs) + * 0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers + * 0 : Minimum 500ns for LV8729, adjusted in stepper.h + * 1 : Minimum for A4988 and A5984 stepper drivers + * 2 : Minimum for DRV8825 stepper drivers + * 3 : Minimum for TB6600 stepper drivers + * 30 : Minimum for TB6560 stepper drivers + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MINIMUM_STEPPER_PULSE 2 + +/** + * Maximum stepping rate (in Hz) the stepper driver allows + * If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE) + * 500000 : Maximum for A4988 stepper driver + * 400000 : Maximum for TMC2xxx stepper drivers + * 250000 : Maximum for DRV8825 stepper driver + * 200000 : Maximum for LV8729 stepper driver + * 150000 : Maximum for TB6600 stepper driver + * 15000 : Maximum for TB6560 stepper driver + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MAXIMUM_STEPPER_RATE 250000 + +// @section temperature + +// Control heater 0 and heater 1 in parallel. +//#define HEATERS_PARALLEL + +//=========================================================================== +//================================= Buffers ================================= +//=========================================================================== + +// @section hidden + +// The number of linear motions that can be in the plan at any give time. +// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2 (e.g. 8, 16, 32) because shifts and ors are used to do the ring-buffering. +#if ENABLED(SDSUPPORT) + #define BLOCK_BUFFER_SIZE 32 // SD,LCD,Buttons take more memory, block buffer needs to be smaller +#else + #define BLOCK_BUFFER_SIZE 16 // maximize block buffer +#endif + +// @section serial + +// The ASCII buffer for serial input +#define MAX_CMD_SIZE 96 +#define BUFSIZE 8 + +// Transmission to Host Buffer Size +// To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0. +// To buffer a simple "ok" you need 4 bytes. +// For ADVANCED_OK (M105) you need 32 bytes. +// For debug-echo: 128 bytes for the optimal speed. +// Other output doesn't need to be that speedy. +// :[0, 2, 4, 8, 16, 32, 64, 128, 256] +#define TX_BUFFER_SIZE 0 + +// Host Receive Buffer Size +// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough. +// To use flow control, set this buffer size to at least 1024 bytes. +// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048] +//#define RX_BUFFER_SIZE 1024 + +#if RX_BUFFER_SIZE >= 1024 + // Enable to have the controller send XON/XOFF control characters to + // the host to signal the RX buffer is becoming full. + //#define SERIAL_XON_XOFF +#endif + +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + +#if ENABLED(SDSUPPORT) + // Enable this option to collect and display the maximum + // RX queue usage after transferring a file to SD. + //#define SERIAL_STATS_MAX_RX_QUEUED + + // Enable this option to collect and display the number + // of dropped bytes after a file transfer to SD. + //#define SERIAL_STATS_DROPPED_RX +#endif + +// Enable an emergency-command parser to intercept certain commands as they +// enter the serial receive buffer, so they cannot be blocked. +// Currently handles M108, M112, M410 +// Does not work on boards using AT90USB (USBCON) processors! +//#define EMERGENCY_PARSER + +// Bad Serial-connections can miss a received command by sending an 'ok' +// Therefore some clients abort after 30 seconds in a timeout. +// Some other clients start sending commands while receiving a 'wait'. +// This "wait" is only sent when the buffer is empty. 1 second is a good value here. +//#define NO_TIMEOUTS 1000 // Milliseconds + +// Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary. +//#define ADVANCED_OK + +// Printrun may have trouble receiving long strings all at once. +// This option inserts short delays between lines of serial output. +#define SERIAL_OVERRUN_PROTECTION + +// @section extras + +/** + * Extra Fan Speed + * Adds a secondary fan speed for each print-cooling fan. + * 'M106 P T3-255' : Set a secondary speed for + * 'M106 P T2' : Use the set secondary speed + * 'M106 P T1' : Restore the previous fan speed + */ +//#define EXTRA_FAN_SPEED + +/** + * Firmware-based and LCD-controlled retract + * + * Add G10 / G11 commands for automatic firmware-based retract / recover. + * Use M207 and M208 to define parameters for retract / recover. + * + * Use M209 to enable or disable auto-retract. + * With auto-retract enabled, all G1 E moves within the set range + * will be converted to firmware-based retract/recover moves. + * + * Be sure to turn off auto-retract during filament change. + * + * Note that M207 / M208 / M209 settings are saved to EEPROM. + * + */ +//#define FWRETRACT +#if ENABLED(FWRETRACT) + #define FWRETRACT_AUTORETRACT // costs ~500 bytes of PROGMEM + #if ENABLED(FWRETRACT_AUTORETRACT) + #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over + #define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion + #endif + #define RETRACT_LENGTH 3 // Default retract length (positive mm) + #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change + #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) + #define RETRACT_ZRAISE 0 // Default retract Z-raise (mm) + #define RETRACT_RECOVER_LENGTH 0 // Default additional recover length (mm, added to retract length when recovering) + #define RETRACT_RECOVER_LENGTH_SWAP 0 // Default additional swap recover length (mm, added to retract length when recovering from extruder change) + #define RETRACT_RECOVER_FEEDRATE 8 // Default feedrate for recovering from retraction (mm/s) + #define RETRACT_RECOVER_FEEDRATE_SWAP 8 // Default feedrate for recovering from swap retraction (mm/s) + #if ENABLED(MIXING_EXTRUDER) + //#define RETRACT_SYNC_MIXING // Retract and restore all mixing steppers simultaneously + #endif +#endif + +/** + * Universal tool change settings. + * Applies to all types of extruders except where explicitly noted. + */ +#if EXTRUDERS > 1 + // Z raise distance for tool-change, as needed for some extruders + #define TOOLCHANGE_ZRAISE 2 // (mm) + //#define TOOLCHANGE_NO_RETURN // Never return to the previous position on tool-change + + // Retract and prime filament on tool-change + //#define TOOLCHANGE_FILAMENT_SWAP + #if ENABLED(TOOLCHANGE_FILAMENT_SWAP) + #define TOOLCHANGE_FIL_SWAP_LENGTH 12 // (mm) + #define TOOLCHANGE_FIL_EXTRA_PRIME 2 // (mm) + #define TOOLCHANGE_FIL_SWAP_RETRACT_SPEED 3600 // (mm/m) + #define TOOLCHANGE_FIL_SWAP_PRIME_SPEED 3600 // (mm/m) + #endif + + /** + * Position to park head during tool change. + * Doesn't apply to SWITCHING_TOOLHEAD, DUAL_X_CARRIAGE, or PARKING_EXTRUDER + */ + //#define TOOLCHANGE_PARK + #if ENABLED(TOOLCHANGE_PARK) + #define TOOLCHANGE_PARK_XY { X_MIN_POS + 10, Y_MIN_POS + 10 } + #define TOOLCHANGE_PARK_XY_FEEDRATE 6000 // (mm/m) + #endif +#endif + +/** + * Advanced Pause + * Experimental feature for filament change support and for parking the nozzle when paused. + * Adds the GCode M600 for initiating filament change. + * If PARK_HEAD_ON_PAUSE enabled, adds the GCode M125 to pause printing and park the nozzle. + * + * Requires an LCD display. + * Requires NOZZLE_PARK_FEATURE. + * This feature is required for the default FILAMENT_RUNOUT_SCRIPT. + */ +#define ADVANCED_PAUSE_FEATURE +#if ENABLED(ADVANCED_PAUSE_FEATURE) + #define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate. + #define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract. + // This short retract is done immediately, before parking the nozzle. + #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast. + #define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. + #define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload. + // For Bowden, the full length of the tube and nozzle. + // For direct drive, the full length of the nozzle. + // Set to 0 for manual unloading. + #define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load. + #define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material. + // 0 to disable start loading and skip to fast load only + #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast. + #define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. + #define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle. + // For Bowden, the full length of the tube and nozzle. + // For direct drive, the full length of the nozzle. + //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted. + #define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate. + #define ADVANCED_PAUSE_PURGE_LENGTH 25 // (mm) Length to extrude after loading. + // Set to 0 for manual extrusion. + // Filament can be extruded repeatedly from the Filament Change menu + // until extrusion is consistent, and to purge old filament. + #define ADVANCED_PAUSE_RESUME_PRIME 0 // (mm) Extra distance to prime nozzle after returning from park. + //#define ADVANCED_PAUSE_FANS_PAUSE // Turn off print-cooling fans while the machine is paused. + + // Filament Unload does a Retract, Delay, and Purge first: + #define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length. + #define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract. + #define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged. + + #define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety. + #define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed. + #define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change. + + //#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change. + //#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change + + #define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu. + //#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302) +#endif + +// @section tmc + +/** + * TMC26X Stepper Driver options + * + * The TMC26XStepper library is required for this stepper driver. + * https://github.com/trinamic/TMC26XStepper + */ +#if HAS_DRIVER(TMC26X) + + #if AXIS_DRIVER_TYPE_X(TMC26X) + #define X_MAX_CURRENT 1000 // (mA) + #define X_SENSE_RESISTOR 91 // (mOhms) + #define X_MICROSTEPS 16 // Number of microsteps + #endif + + #if AXIS_DRIVER_TYPE_X2(TMC26X) + #define X2_MAX_CURRENT 1000 + #define X2_SENSE_RESISTOR 91 + #define X2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Y(TMC26X) + #define Y_MAX_CURRENT 1000 + #define Y_SENSE_RESISTOR 91 + #define Y_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Y2(TMC26X) + #define Y2_MAX_CURRENT 1000 + #define Y2_SENSE_RESISTOR 91 + #define Y2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z(TMC26X) + #define Z_MAX_CURRENT 1000 + #define Z_SENSE_RESISTOR 91 + #define Z_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z2(TMC26X) + #define Z2_MAX_CURRENT 1000 + #define Z2_SENSE_RESISTOR 91 + #define Z2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z3(TMC26X) + #define Z3_MAX_CURRENT 1000 + #define Z3_SENSE_RESISTOR 91 + #define Z3_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E0(TMC26X) + #define E0_MAX_CURRENT 1000 + #define E0_SENSE_RESISTOR 91 + #define E0_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E1(TMC26X) + #define E1_MAX_CURRENT 1000 + #define E1_SENSE_RESISTOR 91 + #define E1_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E2(TMC26X) + #define E2_MAX_CURRENT 1000 + #define E2_SENSE_RESISTOR 91 + #define E2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E3(TMC26X) + #define E3_MAX_CURRENT 1000 + #define E3_SENSE_RESISTOR 91 + #define E3_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E4(TMC26X) + #define E4_MAX_CURRENT 1000 + #define E4_SENSE_RESISTOR 91 + #define E4_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E5(TMC26X) + #define E5_MAX_CURRENT 1000 + #define E5_SENSE_RESISTOR 91 + #define E5_MICROSTEPS 16 + #endif + +#endif // TMC26X + +// @section tmc_smart + +/** + * To use TMC2130, TMC2160, TMC2660, TMC5130, TMC5160 stepper drivers in SPI mode + * connect your SPI pins to the hardware SPI interface on your board and define + * the required CS pins in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 + * pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.). + * You may also use software SPI if you wish to use general purpose IO pins. + * + * To use TMC2208 stepper UART-configurable stepper drivers connect #_SERIAL_TX_PIN + * to the driver side PDN_UART pin with a 1K resistor. + * To use the reading capabilities, also connect #_SERIAL_RX_PIN to PDN_UART without + * a resistor. + * The drivers can also be used with hardware serial. + * + * TMCStepper library is required to use TMC stepper drivers. + * https://github.com/teemuatlut/TMCStepper + */ +#if HAS_TRINAMIC + + #define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current + #define INTERPOLATE true // Interpolate X/Y/Z_MICROSTEPS to 256 + + #if AXIS_IS_TMC(X) + #define X_CURRENT 800 // (mA) RMS current. Multiply by 1.414 for peak current. + #define X_MICROSTEPS 16 // 0..256 + #define X_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(X2) + #define X2_CURRENT 800 + #define X2_MICROSTEPS 16 + #define X2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Y) + #define Y_CURRENT 800 + #define Y_MICROSTEPS 16 + #define Y_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Y2) + #define Y2_CURRENT 800 + #define Y2_MICROSTEPS 16 + #define Y2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Z) + #define Z_CURRENT 800 + #define Z_MICROSTEPS 16 + #define Z_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Z2) + #define Z2_CURRENT 800 + #define Z2_MICROSTEPS 16 + #define Z2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Z3) + #define Z3_CURRENT 800 + #define Z3_MICROSTEPS 16 + #define Z3_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E0) + #define E0_CURRENT 800 + #define E0_MICROSTEPS 16 + #define E0_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E1) + #define E1_CURRENT 800 + #define E1_MICROSTEPS 16 + #define E1_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E2) + #define E2_CURRENT 800 + #define E2_MICROSTEPS 16 + #define E2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E3) + #define E3_CURRENT 800 + #define E3_MICROSTEPS 16 + #define E3_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E4) + #define E4_CURRENT 800 + #define E4_MICROSTEPS 16 + #define E4_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E5) + #define E5_CURRENT 800 + #define E5_MICROSTEPS 16 + #define E5_RSENSE 0.11 + #endif + + /** + * Override default SPI pins for TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160 drivers here. + * The default pins can be found in your board's pins file. + */ + //#define X_CS_PIN -1 + //#define Y_CS_PIN -1 + //#define Z_CS_PIN -1 + //#define X2_CS_PIN -1 + //#define Y2_CS_PIN -1 + //#define Z2_CS_PIN -1 + //#define Z3_CS_PIN -1 + //#define E0_CS_PIN -1 + //#define E1_CS_PIN -1 + //#define E2_CS_PIN -1 + //#define E3_CS_PIN -1 + //#define E4_CS_PIN -1 + //#define E5_CS_PIN -1 + + /** + * Software option for SPI driven drivers (TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160). + * The default SW SPI pins are defined the respective pins files, + * but you can override or define them here. + */ + //#define TMC_USE_SW_SPI + //#define TMC_SW_MOSI -1 + //#define TMC_SW_MISO -1 + //#define TMC_SW_SCK -1 + + /** + * Four TMC2209 drivers can use the same HW/SW serial port with hardware configured addresses. + * Set the address using jumpers on pins MS1 and MS2. + * Address | MS1 | MS2 + * 0 | LOW | LOW + * 1 | HIGH | LOW + * 2 | LOW | HIGH + * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. + */ + #define X_SLAVE_ADDRESS 0 + #define Y_SLAVE_ADDRESS 0 + #define Z_SLAVE_ADDRESS 0 + #define X2_SLAVE_ADDRESS 0 + #define Y2_SLAVE_ADDRESS 0 + #define Z2_SLAVE_ADDRESS 0 + #define Z3_SLAVE_ADDRESS 0 + #define E0_SLAVE_ADDRESS 0 + #define E1_SLAVE_ADDRESS 0 + #define E2_SLAVE_ADDRESS 0 + #define E3_SLAVE_ADDRESS 0 + #define E4_SLAVE_ADDRESS 0 + #define E5_SLAVE_ADDRESS 0 + + /** + * Software enable + * + * Use for drivers that do not use a dedicated enable pin, but rather handle the same + * function through a communication line such as SPI or UART. + */ + //#define SOFTWARE_DRIVER_ENABLE + + /** + * TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only + * Use Trinamic's ultra quiet stepping mode. + * When disabled, Marlin will use spreadCycle stepping mode. + */ + #define STEALTHCHOP_XY + #define STEALTHCHOP_Z + #define STEALTHCHOP_E + + /** + * Optimize spreadCycle chopper parameters by using predefined parameter sets + * or with the help of an example included in the library. + * Provided parameter sets are + * CHOPPER_DEFAULT_12V + * CHOPPER_DEFAULT_19V + * CHOPPER_DEFAULT_24V + * CHOPPER_DEFAULT_36V + * CHOPPER_PRUSAMK3_24V // Imported parameters from the official Prusa firmware for MK3 (24V) + * CHOPPER_MARLIN_119 // Old defaults from Marlin v1.1.9 + * + * Define you own with + * { , , hysteresis_start[1..8] } + */ + #define CHOPPER_TIMING CHOPPER_DEFAULT_12V + + /** + * Monitor Trinamic drivers for error conditions, + * like overtemperature and short to ground. + * In the case of overtemperature Marlin can decrease the driver current until error condition clears. + * Other detected conditions can be used to stop the current print. + * Relevant g-codes: + * M906 - Set or get motor current in milliamps using axis codes X, Y, Z, E. Report values if no axis codes given. + * M911 - Report stepper driver overtemperature pre-warn condition. + * M912 - Clear stepper driver overtemperature pre-warn condition flag. + * M122 - Report driver parameters (Requires TMC_DEBUG) + */ + //#define MONITOR_DRIVER_STATUS + + #if ENABLED(MONITOR_DRIVER_STATUS) + #define CURRENT_STEP_DOWN 50 // [mA] + #define REPORT_CURRENT_CHANGE + #define STOP_ON_ERROR + #endif + + /** + * TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only + * The driver will switch to spreadCycle when stepper speed is over HYBRID_THRESHOLD. + * This mode allows for faster movements at the expense of higher noise levels. + * STEALTHCHOP_(XY|Z|E) must be enabled to use HYBRID_THRESHOLD. + * M913 X/Y/Z/E to live tune the setting + */ + //#define HYBRID_THRESHOLD + + #define X_HYBRID_THRESHOLD 100 // [mm/s] + #define X2_HYBRID_THRESHOLD 100 + #define Y_HYBRID_THRESHOLD 100 + #define Y2_HYBRID_THRESHOLD 100 + #define Z_HYBRID_THRESHOLD 3 + #define Z2_HYBRID_THRESHOLD 3 + #define Z3_HYBRID_THRESHOLD 3 + #define E0_HYBRID_THRESHOLD 30 + #define E1_HYBRID_THRESHOLD 30 + #define E2_HYBRID_THRESHOLD 30 + #define E3_HYBRID_THRESHOLD 30 + #define E4_HYBRID_THRESHOLD 30 + #define E5_HYBRID_THRESHOLD 30 + + /** + * TMC2130, TMC2160, TMC2209, TMC2660, TMC5130, and TMC5160 only + * Use StallGuard2 to sense an obstacle and trigger an endstop. + * Connect the stepper driver's DIAG1 pin to the X/Y endstop pin. + * X, Y, and Z homing will always be done in spreadCycle mode. + * + * X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity. + * Higher values make the system LESS sensitive. + * Lower value make the system MORE sensitive. + * Too low values can lead to false positives, while too high values will collide the axis without triggering. + * It is advised to set X/Y/Z_HOME_BUMP_MM to 0. + * M914 X/Y/Z to live tune the setting + */ + //#define SENSORLESS_HOMING // StallGuard capable drivers only + + /** + * Use StallGuard2 to probe the bed with the nozzle. + * + * CAUTION: This could cause damage to machines that use a lead screw or threaded rod + * to move the Z axis. Take extreme care when attempting to enable this feature. + */ + //#define SENSORLESS_PROBING // StallGuard capable drivers only + + #if EITHER(SENSORLESS_HOMING, SENSORLESS_PROBING) + // TMC2209: 0...255. TMC2130: -64...63 + #define X_STALL_SENSITIVITY 8 + #define Y_STALL_SENSITIVITY 8 + //#define Z_STALL_SENSITIVITY 8 + #endif + + /** + * Beta feature! + * Create a 50/50 square wave step pulse optimal for stepper drivers. + */ + //#define SQUARE_WAVE_STEPPING + + /** + * Enable M122 debugging command for TMC stepper drivers. + * M122 S0/1 will enable continous reporting. + */ + //#define TMC_DEBUG + + /** + * You can set your own advanced settings by filling in predefined functions. + * A list of available functions can be found on the library github page + * https://github.com/teemuatlut/TMCStepper + * + * Example: + * #define TMC_ADV() { \ + * stepperX.diag0_temp_prewarn(1); \ + * stepperY.interpolate(0); \ + * } + */ + #define TMC_ADV() { } + +#endif // HAS_TRINAMIC + +// @section L6470 + +/** + * L6470 Stepper Driver options + * + * Arduino-L6470 library (0.7.0 or higher) is required for this stepper driver. + * https://github.com/ameyer/Arduino-L6470 + * + * Requires the following to be defined in your pins_YOUR_BOARD file + * L6470_CHAIN_SCK_PIN + * L6470_CHAIN_MISO_PIN + * L6470_CHAIN_MOSI_PIN + * L6470_CHAIN_SS_PIN + * L6470_RESET_CHAIN_PIN (optional) + */ +#if HAS_DRIVER(L6470) + + //#define L6470_CHITCHAT // Display additional status info + + #if AXIS_DRIVER_TYPE_X(L6470) + #define X_MICROSTEPS 128 // Number of microsteps (VALID: 1, 2, 4, 8, 16, 32, 128) + #define X_OVERCURRENT 2000 // (mA) Current where the driver detects an over current (VALID: 375 x (1 - 16) - 6A max - rounds down) + #define X_STALLCURRENT 1500 // (mA) Current where the driver detects a stall (VALID: 31.25 * (1-128) - 4A max - rounds down) + #define X_MAX_VOLTAGE 127 // 0-255, Maximum effective voltage seen by stepper + #define X_CHAIN_POS 0 // Position in SPI chain, 0=Not in chain, 1=Nearest MOSI + #endif + + #if AXIS_DRIVER_TYPE_X2(L6470) + #define X2_MICROSTEPS 128 + #define X2_OVERCURRENT 2000 + #define X2_STALLCURRENT 1500 + #define X2_MAX_VOLTAGE 127 + #define X2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Y(L6470) + #define Y_MICROSTEPS 128 + #define Y_OVERCURRENT 2000 + #define Y_STALLCURRENT 1500 + #define Y_MAX_VOLTAGE 127 + #define Y_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Y2(L6470) + #define Y2_MICROSTEPS 128 + #define Y2_OVERCURRENT 2000 + #define Y2_STALLCURRENT 1500 + #define Y2_MAX_VOLTAGE 127 + #define Y2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Z(L6470) + #define Z_MICROSTEPS 128 + #define Z_OVERCURRENT 2000 + #define Z_STALLCURRENT 1500 + #define Z_MAX_VOLTAGE 127 + #define Z_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Z2(L6470) + #define Z2_MICROSTEPS 128 + #define Z2_OVERCURRENT 2000 + #define Z2_STALLCURRENT 1500 + #define Z2_MAX_VOLTAGE 127 + #define Z2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Z3(L6470) + #define Z3_MICROSTEPS 128 + #define Z3_OVERCURRENT 2000 + #define Z3_STALLCURRENT 1500 + #define Z3_MAX_VOLTAGE 127 + #define Z3_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E0(L6470) + #define E0_MICROSTEPS 128 + #define E0_OVERCURRENT 2000 + #define E0_STALLCURRENT 1500 + #define E0_MAX_VOLTAGE 127 + #define E0_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E1(L6470) + #define E1_MICROSTEPS 128 + #define E1_OVERCURRENT 2000 + #define E1_STALLCURRENT 1500 + #define E1_MAX_VOLTAGE 127 + #define E1_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E2(L6470) + #define E2_MICROSTEPS 128 + #define E2_OVERCURRENT 2000 + #define E2_STALLCURRENT 1500 + #define E2_MAX_VOLTAGE 127 + #define E2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E3(L6470) + #define E3_MICROSTEPS 128 + #define E3_OVERCURRENT 2000 + #define E3_STALLCURRENT 1500 + #define E3_MAX_VOLTAGE 127 + #define E3_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E4(L6470) + #define E4_MICROSTEPS 128 + #define E4_OVERCURRENT 2000 + #define E4_STALLCURRENT 1500 + #define E4_MAX_VOLTAGE 127 + #define E4_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E5(L6470) + #define E5_MICROSTEPS 128 + #define E5_OVERCURRENT 2000 + #define E5_STALLCURRENT 1500 + #define E5_MAX_VOLTAGE 127 + #define E5_CHAIN_POS 0 + #endif + + /** + * Monitor L6470 drivers for error conditions like over temperature and over current. + * In the case of over temperature Marlin can decrease the drive until the error condition clears. + * Other detected conditions can be used to stop the current print. + * Relevant g-codes: + * M906 - I1/2/3/4/5 Set or get motor drive level using axis codes X, Y, Z, E. Report values if no axis codes given. + * I not present or I0 or I1 - X, Y, Z or E0 + * I2 - X2, Y2, Z2 or E1 + * I3 - Z3 or E3 + * I4 - E4 + * I5 - E5 + * M916 - Increase drive level until get thermal warning + * M917 - Find minimum current thresholds + * M918 - Increase speed until max or error + * M122 S0/1 - Report driver parameters + */ + //#define MONITOR_L6470_DRIVER_STATUS + + #if ENABLED(MONITOR_L6470_DRIVER_STATUS) + #define KVAL_HOLD_STEP_DOWN 1 + //#define L6470_STOP_ON_ERROR + #endif + +#endif // L6470 + +/** + * TWI/I2C BUS + * + * This feature is an EXPERIMENTAL feature so it shall not be used on production + * machines. Enabling this will allow you to send and receive I2C data from slave + * devices on the bus. + * + * ; Example #1 + * ; This macro send the string "Marlin" to the slave device with address 0x63 (99) + * ; It uses multiple M260 commands with one B arg + * M260 A99 ; Target slave address + * M260 B77 ; M + * M260 B97 ; a + * M260 B114 ; r + * M260 B108 ; l + * M260 B105 ; i + * M260 B110 ; n + * M260 S1 ; Send the current buffer + * + * ; Example #2 + * ; Request 6 bytes from slave device with address 0x63 (99) + * M261 A99 B5 + * + * ; Example #3 + * ; Example serial output of a M261 request + * echo:i2c-reply: from:99 bytes:5 data:hello + */ + +// @section i2cbus + +//#define EXPERIMENTAL_I2CBUS +#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave + +// @section extras + +/** + * Photo G-code + * Add the M240 G-code to take a photo. + * The photo can be triggered by a digital pin or a physical movement. + */ +//#define PHOTO_GCODE +#if ENABLED(PHOTO_GCODE) + // A position to move to (and raise Z) before taking the photo + //#define PHOTO_POSITION { X_MAX_POS - 5, Y_MAX_POS, 0 } // { xpos, ypos, zraise } (M240 X Y Z) + //#define PHOTO_DELAY_MS 100 // (ms) Duration to pause before moving back (M240 P) + //#define PHOTO_RETRACT_MM 6.5 // (mm) E retract/recover for the photo move (M240 R S) + + // Canon RC-1 or homebrew digital camera trigger + // Data from: http://www.doc-diy.net/photo/rc-1_hacked/ + //#define PHOTOGRAPH_PIN 23 + + // Canon Hack Development Kit + // http://captain-slow.dk/2014/03/09/3d-printing-timelapses/ + //#define CHDK_PIN 4 + + // Optional second move with delay to trigger the camera shutter + //#define PHOTO_SWITCH_POSITION { X_MAX_POS, Y_MAX_POS } // { xpos, ypos } (M240 I J) + + // Duration to hold the switch or keep CHDK_PIN high + //#define PHOTO_SWITCH_MS 50 // (ms) (M240 D) +#endif + +/** + * Spindle & Laser control + * + * Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and + * to set spindle speed, spindle direction, and laser power. + * + * SuperPid is a router/spindle speed controller used in the CNC milling community. + * Marlin can be used to turn the spindle on and off. It can also be used to set + * the spindle speed from 5,000 to 30,000 RPM. + * + * You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V + * hardware PWM pin for the speed control and a pin for the rotation direction. + * + * See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details. + */ +//#define SPINDLE_FEATURE +//#define LASER_FEATURE +#if EITHER(SPINDLE_FEATURE, LASER_FEATURE) + #define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH + #define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power + #define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower + #define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power + #define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop + + #if ENABLED(SPINDLE_FEATURE) + //#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction + #define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction + #define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed + + /** + * The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power + * + * SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT + * where PWM duty cycle varies from 0 to 255 + * + * set the following for your controller (ALL MUST BE SET) + */ + #define SPEED_POWER_SLOPE 118.4 + #define SPEED_POWER_INTERCEPT 0 + #define SPEED_POWER_MIN 5000 + #define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM + #else + #define SPEED_POWER_SLOPE 0.3922 + #define SPEED_POWER_INTERCEPT 0 + #define SPEED_POWER_MIN 10 + #define SPEED_POWER_MAX 100 // 0-100% + #endif +#endif + +/** + * Coolant Control + * + * Add the M7, M8, and M9 commands to turn mist or flood coolant on and off. + * + * Note: COOLANT_MIST_PIN and/or COOLANT_FLOOD_PIN must also be defined. + */ +//#define COOLANT_CONTROL +#if ENABLED(COOLANT_CONTROL) + #define COOLANT_MIST // Enable if mist coolant is present + #define COOLANT_FLOOD // Enable if flood coolant is present + #define COOLANT_MIST_INVERT false // Set "true" if the on/off function is reversed + #define COOLANT_FLOOD_INVERT false // Set "true" if the on/off function is reversed +#endif + +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define FILWIDTH_ERROR_MARGIN 1.0 // (mm) If a measurement differs too much from nominal width ignore it + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + +/** + * CNC Coordinate Systems + * + * Enables G53 and G54-G59.3 commands to select coordinate systems + * and G92.1 to reset the workspace to native machine space. + */ +//#define CNC_COORDINATE_SYSTEMS + +/** + * Auto-report temperatures with M155 S + */ +#define AUTO_REPORT_TEMPERATURES + +/** + * Include capabilities in M115 output + */ +#define EXTENDED_CAPABILITIES_REPORT + +/** + * Disable all Volumetric extrusion options + */ +//#define NO_VOLUMETRICS + +#if DISABLED(NO_VOLUMETRICS) + /** + * Volumetric extrusion default state + * Activate to make volumetric extrusion the default method, + * with DEFAULT_NOMINAL_FILAMENT_DIA as the default diameter. + * + * M200 D0 to disable, M200 Dn to set a new diameter. + */ + //#define VOLUMETRIC_DEFAULT_ON +#endif + +/** + * Enable this option for a leaner build of Marlin that removes all + * workspace offsets, simplifying coordinate transformations, leveling, etc. + * + * - M206 and M428 are disabled. + * - G92 will revert to its behavior from Marlin 1.0. + */ +//#define NO_WORKSPACE_OFFSETS + +/** + * Set the number of proportional font spaces required to fill up a typical character space. + * This can help to better align the output of commands like `G29 O` Mesh Output. + * + * For clients that use a fixed-width font (like OctoPrint), leave this set to 1.0. + * Otherwise, adjust according to your client and font. + */ +#define PROPORTIONAL_FONT_RATIO 1.0 + +/** + * Spend 28 bytes of SRAM to optimize the GCode parser + */ +#define FASTER_GCODE_PARSER + +/** + * CNC G-code options + * Support CNC-style G-code dialects used by laser cutters, drawing machine cams, etc. + * Note that G0 feedrates should be used with care for 3D printing (if used at all). + * High feedrates may cause ringing and harm print quality. + */ +//#define PAREN_COMMENTS // Support for parentheses-delimited comments +//#define GCODE_MOTION_MODES // Remember the motion mode (G0 G1 G2 G3 G5 G38.X) and apply for X Y Z E F, etc. + +// Enable and set a (default) feedrate for all G0 moves +//#define G0_FEEDRATE 3000 // (mm/m) +#ifdef G0_FEEDRATE + //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode +#endif + +/** + * G-code Macros + * + * Add G-codes M810-M819 to define and run G-code macros. + * Macros are not saved to EEPROM. + */ +//#define GCODE_MACROS +#if ENABLED(GCODE_MACROS) + #define GCODE_MACROS_SLOTS 5 // Up to 10 may be used + #define GCODE_MACROS_SLOT_SIZE 50 // Maximum length of a single macro +#endif + +/** + * User-defined menu items that execute custom GCode + */ +//#define CUSTOM_USER_MENUS +#if ENABLED(CUSTOM_USER_MENUS) + //#define CUSTOM_USER_MENU_TITLE "Custom Commands" + #define USER_SCRIPT_DONE "M117 User Script Done" + #define USER_SCRIPT_AUDIBLE_FEEDBACK + //#define USER_SCRIPT_RETURN // Return to status screen after a script + + #define USER_DESC_1 "Home & UBL Info" + #define USER_GCODE_1 "G28\nG29 W" + + #define USER_DESC_2 "Preheat for " PREHEAT_1_LABEL + #define USER_GCODE_2 "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND) + + #define USER_DESC_3 "Preheat for " PREHEAT_2_LABEL + #define USER_GCODE_3 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND) + + #define USER_DESC_4 "Heat Bed/Home/Level" + #define USER_GCODE_4 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29" + + #define USER_DESC_5 "Home & Info" + #define USER_GCODE_5 "G28\nM503" +#endif + +/** + * Host Action Commands + * + * Define host streamer action commands in compliance with the standard. + * + * See https://reprap.org/wiki/G-code#Action_commands + * Common commands ........ poweroff, pause, paused, resume, resumed, cancel + * G29_RETRY_AND_RECOVER .. probe_rewipe, probe_failed + * + * Some features add reason codes to extend these commands. + * + * Host Prompt Support enables Marlin to use the host for user prompts so + * filament runout and other processes can be managed from the host side. + */ +//#define HOST_ACTION_COMMANDS +#if ENABLED(HOST_ACTION_COMMANDS) + //#define HOST_PROMPT_SUPPORT +#endif + +//=========================================================================== +//====================== I2C Position Encoder Settings ====================== +//=========================================================================== + +/** + * I2C position encoders for closed loop control. + * Developed by Chris Barr at Aus3D. + * + * Wiki: http://wiki.aus3d.com.au/Magnetic_Encoder + * Github: https://github.com/Aus3D/MagneticEncoder + * + * Supplier: http://aus3d.com.au/magnetic-encoder-module + * Alternative Supplier: http://reliabuild3d.com/ + * + * Reliabuild encoders have been modified to improve reliability. + */ + +//#define I2C_POSITION_ENCODERS +#if ENABLED(I2C_POSITION_ENCODERS) + + #define I2CPE_ENCODER_CNT 1 // The number of encoders installed; max of 5 + // encoders supported currently. + + #define I2CPE_ENC_1_ADDR I2CPE_PRESET_ADDR_X // I2C address of the encoder. 30-200. + #define I2CPE_ENC_1_AXIS X_AXIS // Axis the encoder module is installed on. _AXIS. + #define I2CPE_ENC_1_TYPE I2CPE_ENC_TYPE_LINEAR // Type of encoder: I2CPE_ENC_TYPE_LINEAR -or- + // I2CPE_ENC_TYPE_ROTARY. + #define I2CPE_ENC_1_TICKS_UNIT 2048 // 1024 for magnetic strips with 2mm poles; 2048 for + // 1mm poles. For linear encoders this is ticks / mm, + // for rotary encoders this is ticks / revolution. + //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper + // steps per full revolution (motor steps/rev * microstepping) + //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the + // printer will attempt to correct the error; errors + // smaller than this are ignored to minimize effects of + // measurement noise / latency (filter). + + #define I2CPE_ENC_2_ADDR I2CPE_PRESET_ADDR_Y // Same as above, but for encoder 2. + #define I2CPE_ENC_2_AXIS Y_AXIS + #define I2CPE_ENC_2_TYPE I2CPE_ENC_TYPE_LINEAR + #define I2CPE_ENC_2_TICKS_UNIT 2048 + //#define I2CPE_ENC_2_TICKS_REV (16 * 200) + //#define I2CPE_ENC_2_INVERT + #define I2CPE_ENC_2_EC_METHOD I2CPE_ECM_MICROSTEP + #define I2CPE_ENC_2_EC_THRESH 0.10 + + #define I2CPE_ENC_3_ADDR I2CPE_PRESET_ADDR_Z // Encoder 3. Add additional configuration options + #define I2CPE_ENC_3_AXIS Z_AXIS // as above, or use defaults below. + + #define I2CPE_ENC_4_ADDR I2CPE_PRESET_ADDR_E // Encoder 4. + #define I2CPE_ENC_4_AXIS E_AXIS + + #define I2CPE_ENC_5_ADDR 34 // Encoder 5. + #define I2CPE_ENC_5_AXIS E_AXIS + + // Default settings for encoders which are enabled, but without settings configured above. + #define I2CPE_DEF_TYPE I2CPE_ENC_TYPE_LINEAR + #define I2CPE_DEF_ENC_TICKS_UNIT 2048 + #define I2CPE_DEF_TICKS_REV (16 * 200) + #define I2CPE_DEF_EC_METHOD I2CPE_ECM_NONE + #define I2CPE_DEF_EC_THRESH 0.1 + + //#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given + // axis after which the printer will abort. Comment out to + // disable abort behavior. + + #define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault + // for this amount of time (in ms) before the encoder + // is trusted again. + + /** + * Position is checked every time a new command is executed from the buffer but during long moves, + * this setting determines the minimum update time between checks. A value of 100 works well with + * error rolling average when attempting to correct only for skips and not for vibration. + */ + #define I2CPE_MIN_UPD_TIME_MS 4 // (ms) Minimum time between encoder checks. + + // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise. + #define I2CPE_ERR_ROLLING_AVERAGE + +#endif // I2C_POSITION_ENCODERS + +/** + * MAX7219 Debug Matrix + * + * Add support for a low-cost 8x8 LED Matrix based on the Max7219 chip as a realtime status display. + * Requires 3 signal wires. Some useful debug options are included to demonstrate its usage. + */ +//#define MAX7219_DEBUG +#if ENABLED(MAX7219_DEBUG) + #define MAX7219_CLK_PIN 64 + #define MAX7219_DIN_PIN 57 + #define MAX7219_LOAD_PIN 44 + + //#define MAX7219_GCODE // Add the M7219 G-code to control the LED matrix + #define MAX7219_INIT_TEST 2 // Do a test pattern at initialization (Set to 2 for spiral) + #define MAX7219_NUMBER_UNITS 1 // Number of Max7219 units in chain. + #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) + // connector at: right=0 bottom=-90 top=90 left=180 + //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side + + /** + * Sample debug features + * If you add more debug displays, be careful to avoid conflicts! + */ + #define MAX7219_DEBUG_PRINTER_ALIVE // Blink corner LED of 8x8 matrix to show that the firmware is functioning + #define MAX7219_DEBUG_PLANNER_HEAD 3 // Show the planner queue head position on this and the next LED matrix row + #define MAX7219_DEBUG_PLANNER_TAIL 5 // Show the planner queue tail position on this and the next LED matrix row + + #define MAX7219_DEBUG_PLANNER_QUEUE 0 // Show the current planner queue depth on this and the next LED matrix row + // If you experience stuttering, reboots, etc. this option can reveal how + // tweaks made to the configuration are affecting the printer in real-time. +#endif + +/** + * NanoDLP Sync support + * + * Add support for Synchronized Z moves when using with NanoDLP. G0/G1 axis moves will output "Z_move_comp" + * string to enable synchronization with DLP projector exposure. This change will allow to use + * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands + */ +//#define NANODLP_Z_SYNC +#if ENABLED(NANODLP_Z_SYNC) + //#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move. + // Default behavior is limited to Z axis only. +#endif + +/** + * WiFi Support (Espressif ESP32 WiFi) + */ +//#define WIFISUPPORT +#if ENABLED(WIFISUPPORT) + #define WIFI_SSID "Wifi SSID" + #define WIFI_PWD "Wifi Password" + //#define WEBSUPPORT // Start a webserver with auto-discovery + //#define OTASUPPORT // Support over-the-air firmware updates +#endif + +/** + * Prusa Multi-Material Unit v2 + * Enable in Configuration.h + */ +#if ENABLED(PRUSA_MMU2) + + // Serial port used for communication with MMU2. + // For AVR enable the UART port used for the MMU. (e.g., internalSerial) + // For 32-bit boards check your HAL for available serial ports. (e.g., Serial2) + #define INTERNAL_SERIAL_PORT 2 + #define MMU2_SERIAL internalSerial + + // Use hardware reset for MMU if a pin is defined for it + //#define MMU2_RST_PIN 23 + + // Enable if the MMU2 has 12V stepper motors (MMU2 Firmware 1.0.2 and up) + //#define MMU2_MODE_12V + + // G-code to execute when MMU2 F.I.N.D.A. probe detects filament runout + #define MMU2_FILAMENT_RUNOUT_SCRIPT "M600" + + // Add an LCD menu for MMU2 + //#define MMU2_MENUS + #if ENABLED(MMU2_MENUS) + // Settings for filament load / unload from the LCD menu. + // This is for Prusa MK3-style extruders. Customize for your hardware. + #define MMU2_FILAMENTCHANGE_EJECT_FEED 80.0 + #define MMU2_LOAD_TO_NOZZLE_SEQUENCE \ + { 7.2, 562 }, \ + { 14.4, 871 }, \ + { 36.0, 1393 }, \ + { 14.4, 871 }, \ + { 50.0, 198 } + + #define MMU2_RAMMING_SEQUENCE \ + { 1.0, 1000 }, \ + { 1.0, 1500 }, \ + { 2.0, 2000 }, \ + { 1.5, 3000 }, \ + { 2.5, 4000 }, \ + { -15.0, 5000 }, \ + { -14.0, 1200 }, \ + { -6.0, 600 }, \ + { 10.0, 700 }, \ + { -10.0, 400 }, \ + { -50.0, 2000 } + + #endif + + //#define MMU2_DEBUG // Write debug info to serial output + +#endif // PRUSA_MMU2 + +/** + * Advanced Print Counter settings + */ +#if ENABLED(PRINTCOUNTER) + #define SERVICE_WARNING_BUZZES 3 + // Activate up to 3 service interval watchdogs + //#define SERVICE_NAME_1 "Service S" + //#define SERVICE_INTERVAL_1 100 // print hours + //#define SERVICE_NAME_2 "Service L" + //#define SERVICE_INTERVAL_2 200 // print hours + //#define SERVICE_NAME_3 "Service 3" + //#define SERVICE_INTERVAL_3 1 // print hours +#endif + +// @section develop + +/** + * M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins + */ +//#define PINS_DEBUGGING + +// Enable Marlin dev mode which adds some special commands +//#define MARLIN_DEV_MODE diff --git a/config/examples/Alfawise/U20/_Statusscreen.h b/config/examples/Alfawise/U20/_Statusscreen.h new file mode 100644 index 0000000000..519c0d06f4 --- /dev/null +++ b/config/examples/Alfawise/U20/_Statusscreen.h @@ -0,0 +1,77 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + +/** + * Custom Status Screen bitmap + * + * Place this file in the root with your configuration files + * and enable CUSTOM_STATUS_SCREEN_IMAGE in Configuration.h. + * + * Use the Marlin Bitmap Converter to make your own: + * http://marlinfw.org/tools/u8glib/converter.html + */ + +#pragma once + +// +// Status Screen Logo bitmap +// +#define STATUS_LOGO_Y 0 +#define STATUS_LOGO_WIDTH 38 + +static unsigned char status_logo_bmp[] PROGMEM = { + B11111111,B11111111,B11111111,B11111111,B11111100, + B10000000,B00000000,B00010000,B00000111,B11111100, + B10000000,B00000000,B00010000,B00000000,B11111100, + B10000000,B00000000,B00110000,B00000000,B01111100, + B10000000,B00000000,B00110000,B00000000,B00111100, + B10000000,B00000000,B01110000,B00000000,B00011100, + B11111111,B10000000,B01110000,B00000000,B00001100, + B11111111,B10000000,B11110000,B11100000,B00001100, + B11111111,B00000000,B11110000,B11111000,B00001100, + B11111111,B00000001,B11110000,B11111100,B00000100, + B11111110,B00000001,B11110000,B11010010,B00000100, + B11111110,B00000011,B11110000,B10101110,B00000100, + B11111100,B00000000,B11110000,B10101111,B00000100, + B11111100,B00000000,B00110000,B10000011,B00000100, + B11111000,B00000000,B00110000,B11111111,B00000100, + B11111000,B00000000,B00010000,B11111111,B00000100, + B11111111,B11100000,B00010000,B10111111,B00000100, + B11111111,B11110000,B00010000,B10101111,B00000100, + B11111111,B11110000,B00010000,B10101110,B00000100, + B11111111,B11110000,B00010000,B10000010,B00000100, + B10000011,B11110000,B00010000,B11111100,B00000100, + B10000001,B11110000,B00010000,B11111000,B00001100, + B10000001,B11100000,B00010000,B11100000,B00001100, + B10000000,B00000000,B00010000,B00000000,B00001100, + B10000000,B00000000,B00110000,B00000000,B00011100, + B11000000,B00000000,B00110000,B00000000,B00111100, + B11000000,B00000000,B01110000,B00000000,B01111100, + B11100000,B00000000,B11110000,B00000000,B11111100, + B11111000,B00000011,B11110000,B00000111,B11111100 +}; + +// +// Use default bitmaps +// +#define STATUS_HOTEND_ANIM +#define STATUS_BED_ANIM +#define STATUS_LOGO_X 0 +#define STATUS_HEATERS_X 50 +#define STATUS_BED_X 74 diff --git a/config/examples/AliExpress/CL-260/Configuration.h b/config/examples/AliExpress/CL-260/Configuration.h index 27fb4e25c3..2bbdf90f98 100644 --- a/config/examples/AliExpress/CL-260/Configuration.h +++ b/config/examples/AliExpress/CL-260/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_RAMPS_14_EFB #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "CL-260" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1523,8 +1529,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1681,6 +1690,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1908,31 +1925,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1966,15 +1964,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1987,6 +1976,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2012,17 +2043,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2118,8 +2156,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/AliExpress/UM2pExt/Configuration.h b/config/examples/AliExpress/UM2pExt/Configuration.h index e78d7833d9..fa4ee0b001 100644 --- a/config/examples/AliExpress/UM2pExt/Configuration.h +++ b/config/examples/AliExpress/UM2pExt/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_ULTIMAIN_2 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu //#define CUSTOM_MACHINE_NAME "3D Printer" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 20 #define TEMP_SENSOR_1 20 @@ -525,7 +531,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1534,8 +1540,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1692,6 +1701,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1919,31 +1936,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // #define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1977,15 +1975,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1998,6 +1987,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2023,17 +2054,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2129,8 +2167,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/AliExpress/UM2pExt/Configuration_adv.h b/config/examples/AliExpress/UM2pExt/Configuration_adv.h index 3c2a174634..f25756506e 100644 --- a/config/examples/AliExpress/UM2pExt/Configuration_adv.h +++ b/config/examples/AliExpress/UM2pExt/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu #define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1751,6 +1759,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2436,6 +2447,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Anet/A2/Configuration.h b/config/examples/Anet/A2/Configuration.h index d958224023..6cac4f5a67 100644 --- a/config/examples/Anet/A2/Configuration.h +++ b/config/examples/Anet/A2/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_ANET_10 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Anet A2" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1523,8 +1529,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1681,6 +1690,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1910,31 +1927,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1968,15 +1966,6 @@ // #define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1989,6 +1978,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2014,17 +2045,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2120,8 +2158,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Anet/A2/Configuration_adv.h b/config/examples/Anet/A2/Configuration_adv.h index 084dbc79e8..c03a9d81ce 100644 --- a/config/examples/Anet/A2/Configuration_adv.h +++ b/config/examples/Anet/A2/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Anet/A2plus/Configuration.h b/config/examples/Anet/A2plus/Configuration.h index c3e7e28402..5e1571006e 100644 --- a/config/examples/Anet/A2plus/Configuration.h +++ b/config/examples/Anet/A2plus/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_ANET_10 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Anet A2+" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1523,8 +1529,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1681,6 +1690,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1910,31 +1927,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1968,15 +1966,6 @@ // #define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1989,6 +1978,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2014,17 +2045,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2120,8 +2158,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Anet/A2plus/Configuration_adv.h b/config/examples/Anet/A2plus/Configuration_adv.h index 084dbc79e8..c03a9d81ce 100644 --- a/config/examples/Anet/A2plus/Configuration_adv.h +++ b/config/examples/Anet/A2plus/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Anet/A6/Configuration.h b/config/examples/Anet/A6/Configuration.h index 0c51b283bf..3876f3a172 100644 --- a/config/examples/Anet/A6/Configuration.h +++ b/config/examples/Anet/A6/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_ANET_10 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Anet A6" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 11 #define TEMP_SENSOR_1 0 @@ -525,7 +531,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1674,8 +1680,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1832,6 +1841,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -2061,31 +2078,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -2119,15 +2117,6 @@ // #define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -2140,6 +2129,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2165,17 +2196,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2271,8 +2309,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Anet/A6/Configuration_adv.h b/config/examples/Anet/A6/Configuration_adv.h index acf404e649..2e0d2cedf2 100644 --- a/config/examples/Anet/A6/Configuration_adv.h +++ b/config/examples/Anet/A6/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Anet/A8/Configuration.h b/config/examples/Anet/A8/Configuration.h index d5da9d2569..1c2e8c71b0 100644 --- a/config/examples/Anet/A8/Configuration.h +++ b/config/examples/Anet/A8/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_ANET_10 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Anet A8" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -278,7 +276,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -360,6 +365,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -396,7 +402,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -521,7 +527,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1536,8 +1542,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1694,6 +1703,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1923,31 +1940,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1981,15 +1979,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -2002,6 +1991,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2027,17 +2058,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2133,8 +2171,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Anet/A8/Configuration_adv.h b/config/examples/Anet/A8/Configuration_adv.h index 90625a9baa..57c0c0faa3 100644 --- a/config/examples/Anet/A8/Configuration_adv.h +++ b/config/examples/Anet/A8/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Anet/A8plus/Configuration.h b/config/examples/Anet/A8plus/Configuration.h index 13dffd5c6b..3cd11edc7e 100644 --- a/config/examples/Anet/A8plus/Configuration.h +++ b/config/examples/Anet/A8plus/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_ANET_10 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Anet A8 plus" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -278,7 +276,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -360,6 +365,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -396,7 +402,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -520,7 +526,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1534,8 +1540,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1692,6 +1701,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1919,31 +1936,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1977,15 +1975,6 @@ // #define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1998,6 +1987,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2023,17 +2054,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2129,8 +2167,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Anet/A8plus/Configuration_adv.h b/config/examples/Anet/A8plus/Configuration_adv.h index f1d6421a9a..be68236907 100644 --- a/config/examples/Anet/A8plus/Configuration_adv.h +++ b/config/examples/Anet/A8plus/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Anet/E16/Configuration.h b/config/examples/Anet/E16/Configuration.h index 031fe518d4..4d941dd2d4 100644 --- a/config/examples/Anet/E16/Configuration.h +++ b/config/examples/Anet/E16/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_ANET_10 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "AnetE16V1.3" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -520,7 +526,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1535,8 +1541,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1693,6 +1702,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1920,31 +1937,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1978,15 +1976,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1999,6 +1988,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2024,17 +2055,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2130,8 +2168,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Anet/E16/Configuration_adv.h b/config/examples/Anet/E16/Configuration_adv.h index ea25ceebfa..e02928bade 100644 --- a/config/examples/Anet/E16/Configuration_adv.h +++ b/config/examples/Anet/E16/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu #define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/AnyCubic/i3/Configuration.h b/config/examples/AnyCubic/i3/Configuration.h index ba2792fbbc..2c46b3024f 100644 --- a/config/examples/AnyCubic/i3/Configuration.h +++ b/config/examples/AnyCubic/i3/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_TRIGORILLA_14 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Anycubic i3" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -519,7 +525,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1533,8 +1539,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1691,6 +1700,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1918,31 +1935,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1976,15 +1974,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1997,6 +1986,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2022,17 +2053,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2128,8 +2166,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/AnyCubic/i3/Configuration_adv.h b/config/examples/AnyCubic/i3/Configuration_adv.h index ce84ca0a77..c467595a71 100644 --- a/config/examples/AnyCubic/i3/Configuration_adv.h +++ b/config/examples/AnyCubic/i3/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/ArmEd/Configuration.h b/config/examples/ArmEd/Configuration.h index 1c74b9ca0f..767274e8a2 100644 --- a/config/examples/ArmEd/Configuration.h +++ b/config/examples/ArmEd/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_ARMED #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu //#define CUSTOM_MACHINE_NAME "3D Printer" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1524,8 +1530,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1682,6 +1691,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1909,31 +1926,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1967,15 +1965,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1988,6 +1977,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2013,17 +2044,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2119,8 +2157,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/ArmEd/Configuration_adv.h b/config/examples/ArmEd/Configuration_adv.h index 043aaaefaf..27590f01a9 100644 --- a/config/examples/ArmEd/Configuration_adv.h +++ b/config/examples/ArmEd/Configuration_adv.h @@ -654,6 +654,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -855,6 +856,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1041,7 +1045,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1139,6 +1143,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1368,6 +1373,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1753,6 +1761,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2438,6 +2449,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Azteeg/X5GT/Configuration.h b/config/examples/Azteeg/X5GT/Configuration.h index 1fa040695e..90593b80b9 100644 --- a/config/examples/Azteeg/X5GT/Configuration.h +++ b/config/examples/Azteeg/X5GT/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_AZTEEG_X5_GT #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu //#define CUSTOM_MACHINE_NAME "3D Printer" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 1 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1523,8 +1529,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1681,6 +1690,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1908,31 +1925,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1966,15 +1964,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1987,6 +1976,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2012,17 +2043,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2118,8 +2156,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration.h b/config/examples/BIBO/TouchX/cyclops/Configuration.h index 89e46bea99..0c18696c7f 100644 --- a/config/examples/BIBO/TouchX/cyclops/Configuration.h +++ b/config/examples/BIBO/TouchX/cyclops/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_MKS_GEN_L #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "BIBO2 Touch X" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1523,8 +1529,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1681,6 +1690,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1908,31 +1925,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1966,15 +1964,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1987,6 +1976,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2012,17 +2043,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2118,8 +2156,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h index 42f0c8c690..b5aeead4ae 100644 --- a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h +++ b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/BIBO/TouchX/default/Configuration.h b/config/examples/BIBO/TouchX/default/Configuration.h index c144505dc5..97d1461aa7 100644 --- a/config/examples/BIBO/TouchX/default/Configuration.h +++ b/config/examples/BIBO/TouchX/default/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_MKS_GEN_L #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "BIBO2 Touch X" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 5 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1523,8 +1529,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1681,6 +1690,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1908,31 +1925,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1966,15 +1964,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1987,6 +1976,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2012,17 +2043,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2118,8 +2156,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/BIBO/TouchX/default/Configuration_adv.h b/config/examples/BIBO/TouchX/default/Configuration_adv.h index 5e96edcc8a..85b81c902d 100644 --- a/config/examples/BIBO/TouchX/default/Configuration_adv.h +++ b/config/examples/BIBO/TouchX/default/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/BQ/Hephestos/Configuration.h b/config/examples/BQ/Hephestos/Configuration.h index bc7e212da8..5929d50c0f 100644 --- a/config/examples/BQ/Hephestos/Configuration.h +++ b/config/examples/BQ/Hephestos/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_RAMPS_14_EFB #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "HEPHESTOS" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -502,7 +508,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1511,8 +1517,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1669,6 +1678,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1896,31 +1913,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1954,15 +1952,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1975,6 +1964,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2000,17 +2031,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2106,8 +2144,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/BQ/Hephestos/Configuration_adv.h b/config/examples/BQ/Hephestos/Configuration_adv.h index 4e4c26ee12..b0252bc3f9 100644 --- a/config/examples/BQ/Hephestos/Configuration_adv.h +++ b/config/examples/BQ/Hephestos/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 120*60, 120*60, 18*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/BQ/Hephestos_2/Configuration.h b/config/examples/BQ/Hephestos_2/Configuration.h index ab241ac0fa..7bb0dadda4 100644 --- a/config/examples/BQ/Hephestos_2/Configuration.h +++ b/config/examples/BQ/Hephestos_2/Configuration.h @@ -137,18 +137,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_BQ_ZUM_MEGA_3D #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "BQ Hephestos 2" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 #define MACHINE_UUID "8d083632-40c5-4649-85b8-43d9ae6c5d55" // BQ Hephestos 2 standard config // @section extruder @@ -285,7 +283,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -367,6 +372,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -403,7 +409,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 70 #define TEMP_SENSOR_1 0 @@ -515,7 +521,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1523,8 +1529,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1681,6 +1690,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1908,31 +1925,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1966,15 +1964,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1987,6 +1976,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2012,17 +2043,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2118,8 +2156,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/BQ/Hephestos_2/Configuration_adv.h b/config/examples/BQ/Hephestos_2/Configuration_adv.h index eb368caee6..733d199181 100644 --- a/config/examples/BQ/Hephestos_2/Configuration_adv.h +++ b/config/examples/BQ/Hephestos_2/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" //#define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -859,6 +860,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -1045,7 +1049,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1143,6 +1147,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1372,6 +1377,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1757,6 +1765,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2442,6 +2453,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/BQ/WITBOX/Configuration.h b/config/examples/BQ/WITBOX/Configuration.h index 34856d9246..1cc2c63a6f 100644 --- a/config/examples/BQ/WITBOX/Configuration.h +++ b/config/examples/BQ/WITBOX/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_RAMPS_14_EFB #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "WITBOX" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -502,7 +508,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1511,8 +1517,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1669,6 +1678,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1896,31 +1913,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1954,15 +1952,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1975,6 +1964,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2000,17 +2031,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2106,8 +2144,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/BQ/WITBOX/Configuration_adv.h b/config/examples/BQ/WITBOX/Configuration_adv.h index 4e4c26ee12..b0252bc3f9 100644 --- a/config/examples/BQ/WITBOX/Configuration_adv.h +++ b/config/examples/BQ/WITBOX/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 120*60, 120*60, 18*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Cartesio/Configuration.h b/config/examples/Cartesio/Configuration.h index d8b2f4fcaa..0b522e9dba 100644 --- a/config/examples/Cartesio/Configuration.h +++ b/config/examples/Cartesio/Configuration.h @@ -129,19 +129,17 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD //#define MOTHERBOARD BOARD_CNCONTROLS_11 #define MOTHERBOARD BOARD_CNCONTROLS_12 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "CartesioE" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -278,7 +276,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -360,6 +365,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -396,7 +402,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 -1 #define TEMP_SENSOR_1 -1 @@ -515,7 +521,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //24V 500W silicone heater on to 4mm glass CartesioW @@ -1522,8 +1528,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1680,6 +1689,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1907,31 +1924,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1965,15 +1963,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1986,6 +1975,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2011,17 +2042,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2117,8 +2155,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Cartesio/Configuration_adv.h b/config/examples/Cartesio/Configuration_adv.h index 7a116cfb76..89083aa7a8 100644 --- a/config/examples/Cartesio/Configuration_adv.h +++ b/config/examples/Cartesio/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Creality/CR-10/Configuration.h b/config/examples/Creality/CR-10/Configuration.h index eab96aa71d..45d39e527f 100644 --- a/config/examples/Creality/CR-10/Configuration.h +++ b/config/examples/Creality/CR-10/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_MELZI_CREALITY #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "CR-10" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -519,7 +525,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //Stock CR-10 Bed Tuned for 70C @@ -1533,8 +1539,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1691,6 +1700,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1918,31 +1935,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1976,15 +1974,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1997,6 +1986,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2022,17 +2053,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2128,8 +2166,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Creality/CR-10/Configuration_adv.h b/config/examples/Creality/CR-10/Configuration_adv.h index 4fbb6261ed..29955ef550 100644 --- a/config/examples/Creality/CR-10/Configuration_adv.h +++ b/config/examples/Creality/CR-10/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2437,6 +2448,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Creality/CR-10S/Configuration.h b/config/examples/Creality/CR-10S/Configuration.h index fb53d1e996..86950e3942 100644 --- a/config/examples/Creality/CR-10S/Configuration.h +++ b/config/examples/Creality/CR-10S/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_RAMPS_CREALITY #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "CR-10S" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1524,8 +1530,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1682,6 +1691,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1909,31 +1926,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1967,15 +1965,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1988,6 +1977,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2013,17 +2044,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2119,8 +2157,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Creality/CR-10S/Configuration_adv.h b/config/examples/Creality/CR-10S/Configuration_adv.h index b415180b8b..6fafc13e6c 100644 --- a/config/examples/Creality/CR-10S/Configuration_adv.h +++ b/config/examples/Creality/CR-10S/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu #define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Creality/CR-10_5S/Configuration.h b/config/examples/Creality/CR-10_5S/Configuration.h index 1f993b4111..c288c3c48d 100644 --- a/config/examples/Creality/CR-10_5S/Configuration.h +++ b/config/examples/Creality/CR-10_5S/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_RAMPS_CREALITY #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "CR-10 S5" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1526,8 +1532,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1684,6 +1693,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1911,31 +1928,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1969,15 +1967,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1990,6 +1979,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2015,17 +2046,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2121,8 +2159,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Creality/CR-10_5S/Configuration_adv.h b/config/examples/Creality/CR-10_5S/Configuration_adv.h index eee21c5363..5291e36354 100644 --- a/config/examples/Creality/CR-10_5S/Configuration_adv.h +++ b/config/examples/Creality/CR-10_5S/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu #define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Creality/CR-10mini/Configuration.h b/config/examples/Creality/CR-10mini/Configuration.h index 08a46ec9ef..c20d79ab9c 100644 --- a/config/examples/Creality/CR-10mini/Configuration.h +++ b/config/examples/Creality/CR-10mini/Configuration.h @@ -138,18 +138,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_MELZI_CREALITY #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "CR-10 Mini" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -286,7 +284,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -368,6 +373,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -404,7 +410,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -528,7 +534,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //Stock CR-10 Bed Tuned for 70C @@ -1542,8 +1548,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1700,6 +1709,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1927,31 +1944,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1985,15 +1983,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -2006,6 +1995,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2031,17 +2062,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2137,8 +2175,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Creality/CR-10mini/Configuration_adv.h b/config/examples/Creality/CR-10mini/Configuration_adv.h index 22eb0ed525..5102bddf52 100644 --- a/config/examples/Creality/CR-10mini/Configuration_adv.h +++ b/config/examples/Creality/CR-10mini/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu #define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Creality/CR-20 Pro/Configuration.h b/config/examples/Creality/CR-20 Pro/Configuration.h index c284920f05..949b9d2de1 100644 --- a/config/examples/Creality/CR-20 Pro/Configuration.h +++ b/config/examples/Creality/CR-20 Pro/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_RAMPS_14_EFB #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "CR-20 Pro" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -518,7 +524,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -743,9 +749,15 @@ #define DEFAULT_RETRACT_ACCELERATION 500 // E acceleration for retracts #define DEFAULT_TRAVEL_ACCELERATION 500 // X, Y, Z acceleration for travel (non printing) moves -// -// Use Junction Deviation instead of traditional Jerk Limiting -// +/** + * Junction Deviation + * + * Use Junction Deviation instead of traditional Jerk Limiting + * + * See: + * https://reprap.org/forum/read.php?1,739819 + * http://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html + */ //#define JUNCTION_DEVIATION #if ENABLED(JUNCTION_DEVIATION) #define JUNCTION_DEVIATION_MM 0.02 // (mm) Distance from real junction edge @@ -1520,8 +1532,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1678,6 +1693,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1905,31 +1928,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1963,15 +1967,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1984,6 +1979,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2009,17 +2046,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2115,8 +2159,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Creality/CR-20 Pro/Configuration_adv.h b/config/examples/Creality/CR-20 Pro/Configuration_adv.h index 6ab4f005ac..dea54a9d4e 100644 --- a/config/examples/Creality/CR-20 Pro/Configuration_adv.h +++ b/config/examples/Creality/CR-20 Pro/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 2*60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu #define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Creality/CR-20 Pro/_Statusscreen.h b/config/examples/Creality/CR-20 Pro/_Statusscreen.h index e7ab39d4bf..e88e5fefa1 100644 --- a/config/examples/Creality/CR-20 Pro/_Statusscreen.h +++ b/config/examples/Creality/CR-20 Pro/_Statusscreen.h @@ -1,9 +1,9 @@ /** * Marlin 3D Printer Firmware - * Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. - * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by diff --git a/config/examples/Creality/CR-20/Configuration.h b/config/examples/Creality/CR-20/Configuration.h index 9ca659e5b9..0d5b8c63ec 100644 --- a/config/examples/Creality/CR-20/Configuration.h +++ b/config/examples/Creality/CR-20/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_RAMPS_14_EFB #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "CR-20" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -518,7 +524,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -743,9 +749,15 @@ #define DEFAULT_RETRACT_ACCELERATION 500 // E acceleration for retracts #define DEFAULT_TRAVEL_ACCELERATION 500 // X, Y, Z acceleration for travel (non printing) moves -// -// Use Junction Deviation instead of traditional Jerk Limiting -// +/** + * Junction Deviation + * + * Use Junction Deviation instead of traditional Jerk Limiting + * + * See: + * https://reprap.org/forum/read.php?1,739819 + * http://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html + */ //#define JUNCTION_DEVIATION #if ENABLED(JUNCTION_DEVIATION) #define JUNCTION_DEVIATION_MM 0.02 // (mm) Distance from real junction edge @@ -1520,8 +1532,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1678,6 +1693,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1905,31 +1928,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1963,15 +1967,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1984,6 +1979,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2009,17 +2046,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2115,8 +2159,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Creality/CR-20/Configuration_adv.h b/config/examples/Creality/CR-20/Configuration_adv.h index c75a664d60..bfa6443514 100644 --- a/config/examples/Creality/CR-20/Configuration_adv.h +++ b/config/examples/Creality/CR-20/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 2*60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu #define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Creality/CR-8/Configuration.h b/config/examples/Creality/CR-8/Configuration.h index 62695f0ba7..60fa44b695 100644 --- a/config/examples/Creality/CR-8/Configuration.h +++ b/config/examples/Creality/CR-8/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_RAMPS_ENDER_4 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "CR-8" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -519,7 +525,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. // Ender-4 @@ -1533,8 +1539,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1691,6 +1700,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1918,31 +1935,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1976,15 +1974,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1997,6 +1986,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2022,17 +2053,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2128,8 +2166,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Creality/CR-8/Configuration_adv.h b/config/examples/Creality/CR-8/Configuration_adv.h index 7b1741f637..b48c8afa27 100644 --- a/config/examples/Creality/CR-8/Configuration_adv.h +++ b/config/examples/Creality/CR-8/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Creality/Ender-2/Configuration.h b/config/examples/Creality/Ender-2/Configuration.h index 84528aa9e6..4eaba1e1cb 100644 --- a/config/examples/Creality/Ender-2/Configuration.h +++ b/config/examples/Creality/Ender-2/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_MELZI_CREALITY #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Ender 3D" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -518,7 +524,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1527,8 +1533,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1685,6 +1694,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1881,7 +1898,7 @@ // MakerLab Mini Panel with graphic // controller and SD support - http://reprap.org/wiki/Mini_panel // -#define MINIPANEL +//#define MINIPANEL // // MaKr3d Makr-Panel with graphic controller and SD support. @@ -1912,36 +1929,17 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 // -//#define MKS_MINI_12864 +#define MKS_MINI_12864 // // FYSETC variant of the MINI12864 graphic controller with SD support @@ -1970,15 +1968,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1991,6 +1980,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2016,17 +2047,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2122,8 +2160,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Creality/Ender-2/Configuration_adv.h b/config/examples/Creality/Ender-2/Configuration_adv.h index dd7ccd0065..66e5404ab0 100644 --- a/config/examples/Creality/Ender-2/Configuration_adv.h +++ b/config/examples/Creality/Ender-2/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 0 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Creality/Ender-3/Configuration.h b/config/examples/Creality/Ender-3/Configuration.h index 32637c7ea8..54b1043b85 100644 --- a/config/examples/Creality/Ender-3/Configuration.h +++ b/config/examples/Creality/Ender-3/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_MELZI_CREALITY #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Ender-3" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -518,7 +524,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1527,8 +1533,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1685,6 +1694,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1912,31 +1929,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1970,15 +1968,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1991,6 +1980,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2016,17 +2047,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2122,8 +2160,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Creality/Ender-3/Configuration_adv.h b/config/examples/Creality/Ender-3/Configuration_adv.h index 6ab4f005ac..dea54a9d4e 100644 --- a/config/examples/Creality/Ender-3/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 2*60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu #define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Creality/Ender-3/README.md b/config/examples/Creality/Ender-3/README.md deleted file mode 100644 index e64f3ec3d2..0000000000 --- a/config/examples/Creality/Ender-3/README.md +++ /dev/null @@ -1,18 +0,0 @@ -# Creality Ender Support - -This branch is a reverse-engineered version based on the unpublished firmware from Creality. It is **not** the authoritative source, but has been carefully re-built by looking at their firmware and inferring the base version and configuration they used. The basis is the firmware version from "Jul 31 2017 10:16:30". It is based on Marlin 1.0.1, because - -* 1.0.0 had very different serial output in `setup()` and overall code structure. -* 1.0.2 changed the `VERSION_STRING` to include a leading space, and `lcd_init` uses `SET_INPUT` instead of `pinMode`. - -Configurations were found by seeing what code was compiled into the firmware, and constants used there. - -For U8Glib, at least version 1.14 and at most 1.17 is used, because - -* 1.12 didn't have the extra speed argument to u8g_InitCom. -* 1.13 didn't have the soft reset instruction for UC1701 initialization. -* 1.18 has a new directory structure. - -## Bitmaps - -The bootscreen and custom status screens come from Creality's firmware. diff --git a/config/examples/Creality/Ender-4/Configuration.h b/config/examples/Creality/Ender-4/Configuration.h index b133785a14..c82b0cd6dc 100644 --- a/config/examples/Creality/Ender-4/Configuration.h +++ b/config/examples/Creality/Ender-4/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_RAMPS_ENDER_4 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Ender-4" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -519,7 +525,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. // Ender-4 @@ -1533,8 +1539,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1691,6 +1700,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1918,31 +1935,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1976,15 +1974,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1997,6 +1986,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2022,17 +2053,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2128,8 +2166,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Creality/Ender-4/Configuration_adv.h b/config/examples/Creality/Ender-4/Configuration_adv.h index 311b32b04e..ce4ed02fb7 100644 --- a/config/examples/Creality/Ender-4/Configuration_adv.h +++ b/config/examples/Creality/Ender-4/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Creality/Ender-5/Configuration.h b/config/examples/Creality/Ender-5/Configuration.h index fd0021b77d..eeae7e0453 100644 --- a/config/examples/Creality/Ender-5/Configuration.h +++ b/config/examples/Creality/Ender-5/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_MELZI_CREALITY #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Ender-5" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -518,7 +524,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -743,9 +749,15 @@ #define DEFAULT_RETRACT_ACCELERATION 500 // E acceleration for retracts #define DEFAULT_TRAVEL_ACCELERATION 500 // X, Y, Z acceleration for travel (non printing) moves -// -// Use Junction Deviation instead of traditional Jerk Limiting -// +/** + * Junction Deviation + * + * Use Junction Deviation instead of traditional Jerk Limiting + * + * See: + * https://reprap.org/forum/read.php?1,739819 + * http://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html + */ //#define JUNCTION_DEVIATION #if ENABLED(JUNCTION_DEVIATION) #define JUNCTION_DEVIATION_MM 0.02 // (mm) Distance from real junction edge @@ -999,7 +1011,7 @@ // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way. #define INVERT_X_DIR true #define INVERT_Y_DIR true -#define INVERT_Z_DIR false +#define INVERT_Z_DIR true // @section extruder @@ -1029,8 +1041,8 @@ // @section machine // The size of the print bed -#define X_BED_SIZE 235 -#define Y_BED_SIZE 235 +#define X_BED_SIZE 220 +#define Y_BED_SIZE 220 // Travel limits (mm) after homing, corresponding to endstop positions. #define X_MIN_POS 0 @@ -1520,8 +1532,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1678,6 +1693,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1905,31 +1928,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1963,15 +1967,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1984,6 +1979,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2009,17 +2046,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2115,8 +2159,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Creality/Ender-5/Configuration_adv.h b/config/examples/Creality/Ender-5/Configuration_adv.h index 6ab4f005ac..d383b1dadd 100644 --- a/config/examples/Creality/Ender-5/Configuration_adv.h +++ b/config/examples/Creality/Ender-5/Configuration_adv.h @@ -638,7 +638,7 @@ #define DEFAULT_STEPPER_DEACTIVE_TIME 120 #define DISABLE_INACTIVE_X true #define DISABLE_INACTIVE_Y true -#define DISABLE_INACTIVE_Z true // Set to false if the nozzle will fall down on your printed part when print has finished. +#define DISABLE_INACTIVE_Z false // Set to false if the nozzle will fall down on your printed part when print has finished. #define DISABLE_INACTIVE_E true #define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 2*60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu #define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Creality/Ender-5/_Bootscreen.h b/config/examples/Creality/Ender-5/_Bootscreen.h index c0cbe560c6..52119ce6be 100644 --- a/config/examples/Creality/Ender-5/_Bootscreen.h +++ b/config/examples/Creality/Ender-5/_Bootscreen.h @@ -1,9 +1,9 @@ /** * Marlin 3D Printer Firmware - * Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. - * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by diff --git a/config/examples/Creality/Ender-5/_Statusscreen.h b/config/examples/Creality/Ender-5/_Statusscreen.h index 0dc0853723..3da18ade4b 100644 --- a/config/examples/Creality/Ender-5/_Statusscreen.h +++ b/config/examples/Creality/Ender-5/_Statusscreen.h @@ -1,9 +1,9 @@ /** * Marlin 3D Printer Firmware - * Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. - * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by diff --git a/config/examples/Dagoma/Disco Ultimate/Configuration.h b/config/examples/Dagoma/Disco Ultimate/Configuration.h index 7ffeb6ff62..53a5b4fe58 100644 --- a/config/examples/Dagoma/Disco Ultimate/Configuration.h +++ b/config/examples/Dagoma/Disco Ultimate/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_RAMPS_DAGOMA #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "DiscoUltimate" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 18 #define TEMP_SENSOR_1 0 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1523,8 +1529,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1681,6 +1690,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1908,31 +1925,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1966,15 +1964,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1987,6 +1976,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2012,17 +2043,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2118,8 +2156,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h index e10ddaed64..185b01f6e9 100644 --- a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h +++ b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu #define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration.h b/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration.h index 9a788a0b39..df462216ca 100644 --- a/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration.h +++ b/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_MKS_GEN_L #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Sidewinder X1" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. // Sidewinder X1 @@ -1528,8 +1534,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1686,6 +1695,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1913,31 +1930,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1971,15 +1969,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1992,6 +1981,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2017,17 +2048,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2123,8 +2161,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h b/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h index 6ec2a2147f..3cdabbfe98 100644 --- a/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h +++ b/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 2*60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Einstart-S/Configuration.h b/config/examples/Einstart-S/Configuration.h index 35b61755f3..97c500ffff 100644 --- a/config/examples/Einstart-S/Configuration.h +++ b/config/examples/Einstart-S/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_EINSTART_S #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "The Shining" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 666 #define TEMP_SENSOR_1 0 @@ -520,7 +526,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1533,8 +1539,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1691,6 +1700,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1918,31 +1935,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - #define U8GLIB_SSD1306 - //#define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1976,15 +1974,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1997,6 +1986,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2017,27 +2048,29 @@ // //#define EXTENSIBLE_UI -// -// Einstart S OLED SSD1306 -// -#define U8GLIB_SH1106_EINSTART - //============================================================================= //=============================== Graphical TFTs ============================== //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2133,8 +2166,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Einstart-S/Configuration_adv.h b/config/examples/Einstart-S/Configuration_adv.h index 515add46d6..6a9b966780 100644 --- a/config/examples/Einstart-S/Configuration_adv.h +++ b/config/examples/Einstart-S/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration.h b/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration.h new file mode 100644 index 0000000000..b60444db17 --- /dev/null +++ b/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration.h @@ -0,0 +1,2222 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Configuration.h + * + * Basic settings such as: + * + * - Type of electronics + * - Type of temperature sensor + * - Printer geometry + * - Endstop configuration + * - LCD controller + * - Extra features + * + * Advanced settings can be found in Configuration_adv.h + * + */ +#define CONFIGURATION_H_VERSION 020000 + +//=========================================================================== +//============================= Getting Started ============================= +//=========================================================================== + +/** + * Here are some standard links for getting your machine calibrated: + * + * http://reprap.org/wiki/Calibration + * http://youtu.be/wAL9d7FgInk + * http://calculator.josefprusa.cz + * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide + * http://www.thingiverse.com/thing:5573 + * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap + * http://www.thingiverse.com/thing:298812 + */ + +//=========================================================================== +//============================= DELTA Printer =============================== +//=========================================================================== +// For a Delta printer start with one of the configuration files in the +// config/examples/delta directory and customize for your machine. +// + +//=========================================================================== +//============================= SCARA Printer =============================== +//=========================================================================== +// For a SCARA printer start with the configuration files in +// config/examples/SCARA and customize for your machine. +// + +// @section info + +// User-specified version info of this build to display in [Pronterface, etc] terminal window during +// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this +// build by the user have been successfully uploaded into firmware. +#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes. +#define SHOW_BOOTSCREEN +#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1 +#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2 + +/** + * *** VENDORS PLEASE READ *** + * + * Marlin allows you to add a custom boot image for Graphical LCDs. + * With this option Marlin will first show your custom screen followed + * by the standard Marlin logo with version number and web URL. + * + * We encourage you to take advantage of this new feature and we also + * respectfully request that you retain the unmodified Marlin boot screen. + */ + +// Enable to show the bitmap in Marlin/_Bootscreen.h on startup. +//#define SHOW_CUSTOM_BOOTSCREEN + +// Enable to show the bitmap in Marlin/_Statusscreen.h on the status screen. +//#define CUSTOM_STATUS_SCREEN_IMAGE + +// @section machine + +/** + * Select the serial port on the board to use for communication with the host. + * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. + * + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] + */ +#define SERIAL_PORT 1 // libmaple 0 for USB ,1 for serial + +/** + * Select a secondary serial port on the board to use for communication with the host. + * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. + * + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] + */ +//#define SERIAL_PORT_2 -1 + +/** + * This setting determines the communication speed of the printer. + * + * 250000 works in most cases, but you might try a lower speed if + * you commonly experience drop-outs during host printing. + * You may try up to 1000000 to speed up SD file transfer. + * + * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000] + */ +#define BAUDRATE 115200 + +// Enable the Bluetooth serial interface on AT90USB devices +//#define BLUETOOTH + +// Choose the name from boards.h that matches your setup +#ifndef MOTHERBOARD + #define MOTHERBOARD BOARD_FYSETC_CHEETAH_V12 +#endif + +// Name displayed in the LCD "Ready" message and Info menu +//#define CUSTOM_MACHINE_NAME "3D Printer" + +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 +//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" + +// @section extruder + +// This defines the number of extruders +// :[1, 2, 3, 4, 5, 6] +#define EXTRUDERS 1 + +// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc. +#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 + +// For Cyclops or any "multi-extruder" that shares a single nozzle. +//#define SINGLENOZZLE + +/** + * Průša MK2 Single Nozzle Multi-Material Multiplexer, and variants. + * + * This device allows one stepper driver on a control board to drive + * two to eight stepper motors, one at a time, in a manner suitable + * for extruders. + * + * This option only allows the multiplexer to switch on tool-change. + * Additional options to configure custom E moves are pending. + */ +//#define MK2_MULTIPLEXER +#if ENABLED(MK2_MULTIPLEXER) + // Override the default DIO selector pins here, if needed. + // Some pins files may provide defaults for these pins. + //#define E_MUX0_PIN 40 // Always Required + //#define E_MUX1_PIN 42 // Needed for 3 to 8 inputs + //#define E_MUX2_PIN 44 // Needed for 5 to 8 inputs +#endif + +/** + * Prusa Multi-Material Unit v2 + * + * Requires NOZZLE_PARK_FEATURE to park print head in case MMU unit fails. + * Requires EXTRUDERS = 5 + * + * For additional configuration see Configuration_adv.h + */ +//#define PRUSA_MMU2 + +// A dual extruder that uses a single stepper motor +//#define SWITCHING_EXTRUDER +#if ENABLED(SWITCHING_EXTRUDER) + #define SWITCHING_EXTRUDER_SERVO_NR 0 + #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3] + #if EXTRUDERS > 3 + #define SWITCHING_EXTRUDER_E23_SERVO_NR 1 + #endif +#endif + +// A dual-nozzle that uses a servomotor to raise/lower one (or both) of the nozzles +//#define SWITCHING_NOZZLE +#if ENABLED(SWITCHING_NOZZLE) + #define SWITCHING_NOZZLE_SERVO_NR 0 + //#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second + #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo) +#endif + +/** + * Two separate X-carriages with extruders that connect to a moving part + * via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN. + */ +//#define PARKING_EXTRUDER + +/** + * Two separate X-carriages with extruders that connect to a moving part + * via a magnetic docking mechanism using movements and no solenoid + * + * project : https://www.thingiverse.com/thing:3080893 + * movements : https://youtu.be/0xCEiG9VS3k + * https://youtu.be/Bqbcs0CU2FE + */ +//#define MAGNETIC_PARKING_EXTRUDER + +#if EITHER(PARKING_EXTRUDER, MAGNETIC_PARKING_EXTRUDER) + + #define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders + #define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder + //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381 + + #if ENABLED(PARKING_EXTRUDER) + + #define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage + #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil + #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined. + //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381 + + #elif ENABLED(MAGNETIC_PARKING_EXTRUDER) + + #define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point + #define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple + #define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point + #define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling + + #endif + +#endif + +/** + * Switching Toolhead + * + * Support for swappable and dockable toolheads, such as + * the E3D Tool Changer. Toolheads are locked with a servo. + */ +//#define SWITCHING_TOOLHEAD + +/** + * Magnetic Switching Toolhead + * + * Support swappable and dockable toolheads with a magnetic + * docking mechanism using movement and no servo. + */ +//#define MAGNETIC_SWITCHING_TOOLHEAD + +/** + * Electromagnetic Switching Toolhead + * + * Parking for CoreXY / HBot kinematics. + * Toolheads are parked at one edge and held with an electromagnet. + * Supports more than 2 Toolheads. See https://youtu.be/JolbsAKTKf4 + */ +//#define ELECTROMAGNETIC_SWITCHING_TOOLHEAD + +#if ANY(SWITCHING_TOOLHEAD, MAGNETIC_SWITCHING_TOOLHEAD, ELECTROMAGNETIC_SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_Y_POS 235 // (mm) Y position of the toolhead dock + #define SWITCHING_TOOLHEAD_Y_SECURITY 10 // (mm) Security distance Y axis + #define SWITCHING_TOOLHEAD_Y_CLEAR 60 // (mm) Minimum distance from dock for unobstructed X axis + #define SWITCHING_TOOLHEAD_X_POS { 215, 0 } // (mm) X positions for parking the extruders + #if ENABLED(SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_SERVO_NR 2 // Index of the servo connector + #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock + #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif + #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching + #endif +#endif + +/** + * "Mixing Extruder" + * - Adds G-codes M163 and M164 to set and "commit" the current mix factors. + * - Extends the stepping routines to move multiple steppers in proportion to the mix. + * - Optional support for Repetier Firmware's 'M164 S' supporting virtual tools. + * - This implementation supports up to two mixing extruders. + * - Enable DIRECT_MIXING_IN_G1 for M165 and mixing in G1 (from Pia Taubert's reference implementation). + */ +//#define MIXING_EXTRUDER +#if ENABLED(MIXING_EXTRUDER) + #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder + #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164 + //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands + //#define GRADIENT_MIX // Support for gradient mixing with M166 and LCD + #if ENABLED(GRADIENT_MIX) + //#define GRADIENT_VTOOL // Add M166 T to use a V-tool index as a Gradient alias + #endif +#endif + +// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). +// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). +// For the other hotends it is their distance from the extruder 0 hotend. +//#define HOTEND_OFFSET_X { 0.0, 20.00 } // (mm) relative X-offset for each nozzle +//#define HOTEND_OFFSET_Y { 0.0, 5.00 } // (mm) relative Y-offset for each nozzle +//#define HOTEND_OFFSET_Z { 0.0, 0.00 } // (mm) relative Z-offset for each nozzle + +// @section machine + +/** + * Power Supply Control + * + * Enable and connect the power supply to the PS_ON_PIN. + * Specify whether the power supply is active HIGH or active LOW. + */ +//#define PSU_CONTROL +//#define PSU_NAME "Power Supply" + +#if ENABLED(PSU_CONTROL) + #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2) + + //#define PS_DEFAULT_OFF // Keep power off until enabled directly with M80 + + //#define AUTO_POWER_CONTROL // Enable automatic control of the PS_ON pin + #if ENABLED(AUTO_POWER_CONTROL) + #define AUTO_POWER_FANS // Turn on PSU if fans need power + #define AUTO_POWER_E_FANS + #define AUTO_POWER_CONTROLLERFAN + #define AUTO_POWER_CHAMBER_FAN + //#define AUTO_POWER_E_TEMP 50 // (°C) Turn on PSU over this temperature + //#define AUTO_POWER_CHAMBER_TEMP 30 // (°C) Turn on PSU over this temperature + #define POWER_TIMEOUT 30 + #endif + +#endif + +// @section temperature + +//=========================================================================== +//============================= Thermal Settings ============================ +//=========================================================================== + +/** + * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table + * + * Temperature sensors available: + * + * -4 : thermocouple with AD8495 + * -3 : thermocouple with MAX31855 (only for sensor 0) + * -2 : thermocouple with MAX6675 (only for sensor 0) + * -1 : thermocouple with AD595 + * 0 : not used + * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 3 : Mendel-parts thermistor (4.7k pullup) + * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! + * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) + * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) + * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) + * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) + * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) + * 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) + * 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) + * 10 : 100k RS thermistor 198-961 (4.7k pullup) + * 11 : 100k beta 3950 1% thermistor (4.7k pullup) + * 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) + * 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" + * 15 : 100k thermistor calibration for JGAurora A5 hotend + * 18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327 + * 20 : the PT100 circuit found in the Ultimainboard V2.x + * 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 + * 61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup + * 66 : 4.7M High Temperature thermistor from Dyze Design + * 67 : 450C thermistor from SliceEngineering + * 70 : the 100K thermistor found in the bq Hephestos 2 + * 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor + * + * 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k. + * (but gives greater accuracy and more stable PID) + * 51 : 100k thermistor - EPCOS (1k pullup) + * 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup) + * 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) + * + * 1047 : Pt1000 with 4k7 pullup + * 1010 : Pt1000 with 1k pullup (non standard) + * 147 : Pt100 with 4k7 pullup + * 110 : Pt100 with 1k pullup (non standard) + * + * 1000 : Custom - Specify parameters in Configuration_adv.h + * + * Use these for Testing or Development purposes. NEVER for production machine. + * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. + * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. + * + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + */ +#define TEMP_SENSOR_0 1 +#define TEMP_SENSOR_1 0 +#define TEMP_SENSOR_2 0 +#define TEMP_SENSOR_3 0 +#define TEMP_SENSOR_4 0 +#define TEMP_SENSOR_5 0 +#define TEMP_SENSOR_BED 1 +#define TEMP_SENSOR_CHAMBER 0 + +// Dummy thermistor constant temperature readings, for use with 998 and 999 +#define DUMMY_THERMISTOR_998_VALUE 25 +#define DUMMY_THERMISTOR_999_VALUE 100 + +// Use temp sensor 1 as a redundant sensor with sensor 0. If the readings +// from the two sensors differ too much the print will be aborted. +//#define TEMP_SENSOR_1_AS_REDUNDANT +#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 + +#define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109 +#define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer +#define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target + +#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190 +#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer +#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target + +// Below this temperature the heater will be switched off +// because it probably indicates a broken thermistor wire. +#define HEATER_0_MINTEMP 5 +#define HEATER_1_MINTEMP 5 +#define HEATER_2_MINTEMP 5 +#define HEATER_3_MINTEMP 5 +#define HEATER_4_MINTEMP 5 +#define HEATER_5_MINTEMP 5 +#define BED_MINTEMP 5 + +// Above this temperature the heater will be switched off. +// This can protect components from overheating, but NOT from shorts and failures. +// (Use MINTEMP for thermistor short/failure protection.) +#define HEATER_0_MAXTEMP 275 +#define HEATER_1_MAXTEMP 275 +#define HEATER_2_MAXTEMP 275 +#define HEATER_3_MAXTEMP 275 +#define HEATER_4_MAXTEMP 275 +#define HEATER_5_MAXTEMP 275 +#define BED_MAXTEMP 150 + +//=========================================================================== +//============================= PID Settings ================================ +//=========================================================================== +// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning + +// Comment the following line to disable PID and enable bang-bang. +#define PIDTEMP +#define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current +#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current +#define PID_K1 0.95 // Smoothing factor within any PID loop +#if ENABLED(PIDTEMP) + //#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM) + //#define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM) + //#define PID_DEBUG // Sends debug data to the serial port. + //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX + //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay + //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] + #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature + // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. + + // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it + + //PID for Makerlab J-head + #define DEFAULT_Kp 21.73 + #define DEFAULT_Ki 1.54 + #define DEFAULT_Kd 76.55 + + // Ultimaker + //#define DEFAULT_Kp 22.2 + //#define DEFAULT_Ki 1.08 + //#define DEFAULT_Kd 114 + + // MakerGear + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 + + // Mendel Parts V9 on 12V + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 + +#endif // PIDTEMP + +//=========================================================================== +//====================== PID > Bed Temperature Control ====================== +//=========================================================================== + +/** + * PID Bed Heating + * + * If this option is enabled set PID constants below. + * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis. + * + * The PID frequency will be the same as the extruder PWM. + * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz, + * which is fine for driving a square wave into a resistive load and does not significantly + * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W + * heater. If your configuration is significantly different than this and you don't understand + * the issues involved, don't use bed PID until someone else verifies that your hardware works. + */ +//#define PIDTEMPBED + +//#define BED_LIMIT_SWITCHING + +/** + * Max Bed Power + * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis). + * When set to any value below 255, enables a form of PWM to the bed that acts like a divider + * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED) + */ +#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current + +#if ENABLED(PIDTEMPBED) + //#define MIN_BED_POWER 0 + //#define PID_BED_DEBUG // Sends debug data to the serial port. + + //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) + //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 + + //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) + //from pidautotune + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 + + // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. +#endif // PIDTEMPBED + +// @section extruder + +/** + * Prevent extrusion if the temperature is below EXTRUDE_MINTEMP. + * Add M302 to set the minimum extrusion temperature and/or turn + * cold extrusion prevention on and off. + * + * *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! *** + */ +#define PREVENT_COLD_EXTRUSION +#define EXTRUDE_MINTEMP 170 + +/** + * Prevent a single extrusion longer than EXTRUDE_MAXLENGTH. + * Note: For Bowden Extruders make this large enough to allow load/unload. + */ +#define PREVENT_LENGTHY_EXTRUDE +#define EXTRUDE_MAXLENGTH 200 + +//=========================================================================== +//======================== Thermal Runaway Protection ======================= +//=========================================================================== + +/** + * Thermal Protection provides additional protection to your printer from damage + * and fire. Marlin always includes safe min and max temperature ranges which + * protect against a broken or disconnected thermistor wire. + * + * The issue: If a thermistor falls out, it will report the much lower + * temperature of the air in the room, and the the firmware will keep + * the heater on. + * + * If you get "Thermal Runaway" or "Heating failed" errors the + * details can be tuned in Configuration_adv.h + */ + +#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders +#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed +#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber + +//=========================================================================== +//============================= Mechanical Settings ========================= +//=========================================================================== + +// @section machine + +// Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics +// either in the usual order or reversed +//#define COREXY +//#define COREXZ +//#define COREYZ +//#define COREYX +//#define COREZX +//#define COREZY + +//=========================================================================== +//============================== Endstop Settings =========================== +//=========================================================================== + +// @section homing + +// Specify here all the endstop connectors that are connected to any endstop or probe. +// Almost all printers will be using one per axis. Probes will use one or more of the +// extra connectors. Leave undefined any used for non-endstop and non-probe purposes. +#define USE_XMIN_PLUG +#define USE_YMIN_PLUG +#define USE_ZMIN_PLUG +//#define USE_XMAX_PLUG +//#define USE_YMAX_PLUG +//#define USE_ZMAX_PLUG + +// Enable pullup for all endstops to prevent a floating state +#define ENDSTOPPULLUPS +#if DISABLED(ENDSTOPPULLUPS) + // Disable ENDSTOPPULLUPS to set pullups individually + //#define ENDSTOPPULLUP_XMAX + //#define ENDSTOPPULLUP_YMAX + //#define ENDSTOPPULLUP_ZMAX + //#define ENDSTOPPULLUP_XMIN + //#define ENDSTOPPULLUP_YMIN + //#define ENDSTOPPULLUP_ZMIN + //#define ENDSTOPPULLUP_ZMIN_PROBE +#endif + +// Enable pulldown for all endstops to prevent a floating state +//#define ENDSTOPPULLDOWNS +#if DISABLED(ENDSTOPPULLDOWNS) + // Disable ENDSTOPPULLDOWNS to set pulldowns individually + //#define ENDSTOPPULLDOWN_XMAX + //#define ENDSTOPPULLDOWN_YMAX + //#define ENDSTOPPULLDOWN_ZMAX + //#define ENDSTOPPULLDOWN_XMIN + //#define ENDSTOPPULLDOWN_YMIN + //#define ENDSTOPPULLDOWN_ZMIN + //#define ENDSTOPPULLDOWN_ZMIN_PROBE +#endif + +// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup). +#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe. + +/** + * Stepper Drivers + * + * These settings allow Marlin to tune stepper driver timing and enable advanced options for + * stepper drivers that support them. You may also override timing options in Configuration_adv.h. + * + * A4988 is assumed for unspecified drivers. + * + * Options: A4988, A5984, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100, + * TMC2130, TMC2130_STANDALONE, TMC2160, TMC2160_STANDALONE, + * TMC2208, TMC2208_STANDALONE, TMC2209, TMC2209_STANDALONE, + * TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE, + * TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE + * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE'] + */ +#define X_DRIVER_TYPE TMC2208 +#define Y_DRIVER_TYPE TMC2208 +#define Z_DRIVER_TYPE TMC2208 +//#define X2_DRIVER_TYPE A4988 +//#define Y2_DRIVER_TYPE A4988 +//#define Z2_DRIVER_TYPE A4988 +//#define Z3_DRIVER_TYPE A4988 +#define E0_DRIVER_TYPE TMC2208 +//#define E1_DRIVER_TYPE A4988 +//#define E2_DRIVER_TYPE A4988 +//#define E3_DRIVER_TYPE A4988 +//#define E4_DRIVER_TYPE A4988 +//#define E5_DRIVER_TYPE A4988 + +// Enable this feature if all enabled endstop pins are interrupt-capable. +// This will remove the need to poll the interrupt pins, saving many CPU cycles. +//#define ENDSTOP_INTERRUPTS_FEATURE + +/** + * Endstop Noise Threshold + * + * Enable if your probe or endstops falsely trigger due to noise. + * + * - Higher values may affect repeatability or accuracy of some bed probes. + * - To fix noise install a 100nF ceramic capacitor inline with the switch. + * - This feature is not required for common micro-switches mounted on PCBs + * based on the Makerbot design, which already have the 100nF capacitor. + * + * :[2,3,4,5,6,7] + */ +//#define ENDSTOP_NOISE_THRESHOLD 2 + +//============================================================================= +//============================== Movement Settings ============================ +//============================================================================= +// @section motion + +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * With this option each E stepper can have its own factors for the + * following movement settings. If fewer factors are given than the + * total number of extruders, the last value applies to the rest. + */ +//#define DISTINCT_E_FACTORS + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] + */ +#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 93 } + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] + */ +#define DEFAULT_MAX_FEEDRATE { 500, 500, 5, 25 } + +/** + * Default Max Acceleration (change/s) change = mm/s + * (Maximum start speed for accelerated moves) + * Override with M201 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] + */ +#define DEFAULT_MAX_ACCELERATION { 500, 500, 100, 5000 } + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 500 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 500 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 500 // X, Y, Z acceleration for travel (non printing) moves + +/** + * Junction Deviation + * + * Use Junction Deviation instead of traditional Jerk Limiting + * + * See: + * https://reprap.org/forum/read.php?1,739819 + * http://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html + */ +//#define JUNCTION_DEVIATION +#if ENABLED(JUNCTION_DEVIATION) + #define JUNCTION_DEVIATION_MM 0.02 // (mm) Distance from real junction edge +#endif + +/** + * Default Jerk (mm/s) + * Override with M205 X Y Z E + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#if DISABLED(JUNCTION_DEVIATION) + #define DEFAULT_XJERK 10.0 + #define DEFAULT_YJERK 10.0 + #define DEFAULT_ZJERK 0.3 +#endif + +#define DEFAULT_EJERK 5.0 // May be used by Linear Advance + +/** + * S-Curve Acceleration + * + * This option eliminates vibration during printing by fitting a Bézier + * curve to move acceleration, producing much smoother direction changes. + * + * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained + */ +//#define S_CURVE_ACCELERATION + +//=========================================================================== +//============================= Z Probe Options ============================= +//=========================================================================== +// @section probes + +// +// See http://marlinfw.org/docs/configuration/probes.html +// + +/** + * Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + * + * Enable this option for a probe connected to the Z Min endstop pin. + */ +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +/** + * Z_MIN_PROBE_PIN + * + * Define this pin if the probe is not connected to Z_MIN_PIN. + * If not defined the default pin for the selected MOTHERBOARD + * will be used. Most of the time the default is what you want. + * + * - The simplest option is to use a free endstop connector. + * - Use 5V for powered (usually inductive) sensors. + * + * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin: + * - For simple switches connect... + * - normally-closed switches to GND and D32. + * - normally-open switches to 5V and D32. + * + */ +//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default + +/** + * Probe Type + * + * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. + * Activate one of these to use Auto Bed Leveling below. + */ + +/** + * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe. + * Use G29 repeatedly, adjusting the Z height at each point with movement commands + * or (with LCD_BED_LEVELING) the LCD controller. + */ +//#define PROBE_MANUALLY +//#define MANUAL_PROBE_START_Z 0.2 + +/** + * A Fix-Mounted Probe either doesn't deploy or needs manual deployment. + * (e.g., an inductive probe or a nozzle-based probe-switch.) + */ +//#define FIX_MOUNTED_PROBE + +/** + * Z Servo Probe, such as an endstop switch on a rotating arm. + */ +//#define Z_PROBE_SERVO_NR 0 // Defaults to SERVO 0 connector. +//#define Z_SERVO_ANGLES { 70, 0 } // Z Servo Deploy and Stow angles + +/** + * The BLTouch probe uses a Hall effect sensor and emulates a servo. + */ +#define BLTOUCH + +/** + * Touch-MI Probe by hotends.fr + * + * This probe is deployed and activated by moving the X-axis to a magnet at the edge of the bed. + * By default, the magnet is assumed to be on the left and activated by a home. If the magnet is + * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position. + * + * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING, + * and a minimum Z_HOMING_HEIGHT of 10. + */ +//#define TOUCH_MI_PROBE +#if ENABLED(TOUCH_MI_PROBE) + #define TOUCH_MI_RETRACT_Z 0.5 // Height at which the probe retracts + //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2) // For a magnet on the right side of the bed + //#define TOUCH_MI_MANUAL_DEPLOY // For manual deploy (LCD menu) +#endif + +// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) +//#define SOLENOID_PROBE + +// A sled-mounted probe like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +// A probe deployed by moving the x-axis, such as the Wilson II's rack-and-pinion probe designed by Marty Rice. +//#define RACK_AND_PINION_PROBE +#if ENABLED(RACK_AND_PINION_PROBE) + #define Z_PROBE_DEPLOY_X X_MIN_POS + #define Z_PROBE_RETRACT_X X_MAX_POS +#endif + +// +// For Z_PROBE_ALLEN_KEY see the Delta example configurations. +// + +/** + * Z Probe to nozzle (X,Y) offset, relative to (0, 0). + * X and Y offsets must be integers. + * + * In the following example the X and Y offsets are both positive: + * #define X_PROBE_OFFSET_FROM_EXTRUDER 10 + * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 + * + * +-- BACK ---+ + * | | + * L | (+) P | R <-- probe (20,20) + * E | | I + * F | (-) N (+) | G <-- nozzle (10,10) + * T | | H + * | (-) | T + * | | + * O-- FRONT --+ + * (0,0) + */ +#define X_PROBE_OFFSET_FROM_EXTRUDER -44 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER -6 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER -3.9 // Z offset: -below +above [the nozzle] + +// Certain types of probes need to stay away from edges +#define MIN_PROBE_EDGE 10 + +// X and Y axis travel speed (mm/m) between probes +#define XY_PROBE_SPEED 8000 + +// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2) +#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z + +// Feedrate (mm/m) for the "accurate" probe of each point +#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) + +/** + * Multiple Probing + * + * You may get improved results by probing 2 or more times. + * With EXTRA_PROBING the more atypical reading(s) will be disregarded. + * + * A total of 2 does fast/slow probes with a weighted average. + * A total of 3 or more adds more slow probes, taking the average. + */ +//#define MULTIPLE_PROBING 2 +//#define EXTRA_PROBING 1 + +/** + * Z probes require clearance when deploying, stowing, and moving between + * probe points to avoid hitting the bed and other hardware. + * Servo-mounted probes require extra space for the arm to rotate. + * Inductive probes need space to keep from triggering early. + * + * Use these settings to specify the distance (mm) to raise the probe (or + * lower the bed). The values set here apply over and above any (negative) + * probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD. + * Only integer values >= 1 are valid here. + * + * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle. + * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle. + */ +#define Z_CLEARANCE_DEPLOY_PROBE 15 // Z Clearance for Deploy/Stow +#define Z_CLEARANCE_BETWEEN_PROBES 10 // Z Clearance between probe points +#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes +//#define Z_AFTER_PROBING 5 // Z position after probing is done + +#define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping + +// For M851 give a range for adjusting the Z probe offset +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + +// Enable the M48 repeatability test to test probe accuracy +//#define Z_MIN_PROBE_REPEATABILITY_TEST + +// Before deploy/stow pause for user confirmation +//#define PAUSE_BEFORE_DEPLOY_STOW +#if ENABLED(PAUSE_BEFORE_DEPLOY_STOW) + //#define PAUSE_PROBE_DEPLOY_WHEN_TRIGGERED // For Manual Deploy Allenkey Probe +#endif + +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + +// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 +// :{ 0:'Low', 1:'High' } +#define X_ENABLE_ON 0 +#define Y_ENABLE_ON 0 +#define Z_ENABLE_ON 0 +#define E_ENABLE_ON 0 // For all extruders + +// Disables axis stepper immediately when it's not being used. +// WARNING: When motors turn off there is a chance of losing position accuracy! +#define DISABLE_X false +#define DISABLE_Y false +#define DISABLE_Z false + +// Warn on display about possibly reduced accuracy +//#define DISABLE_REDUCED_ACCURACY_WARNING + +// @section extruder + +#define DISABLE_E false // For all extruders +#define DISABLE_INACTIVE_EXTRUDER // Keep only the active extruder enabled + +// @section machine + +// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way. +#define INVERT_X_DIR true +#define INVERT_Y_DIR true +#define INVERT_Z_DIR false + +// @section extruder + +// For direct drive extruder v9 set to true, for geared extruder set to false. +#define INVERT_E0_DIR true +#define INVERT_E1_DIR false +#define INVERT_E2_DIR false +#define INVERT_E3_DIR false +#define INVERT_E4_DIR false +#define INVERT_E5_DIR false + +// @section homing + +//#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed + +//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off. + +//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ... + // Be sure you have this distance over your Z_MAX_POS in case. + +// Direction of endstops when homing; 1=MAX, -1=MIN +// :[-1,1] +#define X_HOME_DIR -1 +#define Y_HOME_DIR -1 +#define Z_HOME_DIR -1 + +// @section machine + +// The size of the print bed +#define X_BED_SIZE 235 +#define Y_BED_SIZE 235 + +// Travel limits (mm) after homing, corresponding to endstop positions. +#define X_MIN_POS 0 +#define Y_MIN_POS 0 +#define Z_MIN_POS 0 +#define X_MAX_POS X_BED_SIZE +#define Y_MAX_POS Y_BED_SIZE +#define Z_MAX_POS 260 + +/** + * Software Endstops + * + * - Prevent moves outside the set machine bounds. + * - Individual axes can be disabled, if desired. + * - X and Y only apply to Cartesian robots. + * - Use 'M211' to set software endstops on/off or report current state + */ + +// Min software endstops constrain movement within minimum coordinate bounds +#define MIN_SOFTWARE_ENDSTOPS +#if ENABLED(MIN_SOFTWARE_ENDSTOPS) + #define MIN_SOFTWARE_ENDSTOP_X + #define MIN_SOFTWARE_ENDSTOP_Y + #define MIN_SOFTWARE_ENDSTOP_Z +#endif + +// Max software endstops constrain movement within maximum coordinate bounds +#define MAX_SOFTWARE_ENDSTOPS +#if ENABLED(MAX_SOFTWARE_ENDSTOPS) + #define MAX_SOFTWARE_ENDSTOP_X + #define MAX_SOFTWARE_ENDSTOP_Y + #define MAX_SOFTWARE_ENDSTOP_Z +#endif + +#if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS) + //#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD +#endif + +/** + * Filament Runout Sensors + * Mechanical or opto endstops are used to check for the presence of filament. + * + * RAMPS-based boards use SERVO3_PIN for the first runout sensor. + * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc. + * By default the firmware assumes HIGH=FILAMENT PRESENT. + */ +//#define FILAMENT_RUNOUT_SENSOR +#if ENABLED(FILAMENT_RUNOUT_SENSOR) + #define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each. + #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor. + #define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins. + //#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins. + + // Set one or more commands to execute on filament runout. + // (After 'M412 H' Marlin will ask the host to handle the process.) + #define FILAMENT_RUNOUT_SCRIPT "M600" + + // After a runout is detected, continue printing this length of filament + // before executing the runout script. Useful for a sensor at the end of + // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead. + //#define FILAMENT_RUNOUT_DISTANCE_MM 25 + + #ifdef FILAMENT_RUNOUT_DISTANCE_MM + // Enable this option to use an encoder disc that toggles the runout pin + // as the filament moves. (Be sure to set FILAMENT_RUNOUT_DISTANCE_MM + // large enough to avoid false positives.) + //#define FILAMENT_MOTION_SENSOR + #endif +#endif + +//=========================================================================== +//=============================== Bed Leveling ============================== +//=========================================================================== +// @section calibrate + +/** + * Choose one of the options below to enable G29 Bed Leveling. The parameters + * and behavior of G29 will change depending on your selection. + * + * If using a Probe for Z Homing, enable Z_SAFE_HOMING also! + * + * - AUTO_BED_LEVELING_3POINT + * Probe 3 arbitrary points on the bed (that aren't collinear) + * You specify the XY coordinates of all 3 points. + * The result is a single tilted plane. Best for a flat bed. + * + * - AUTO_BED_LEVELING_LINEAR + * Probe several points in a grid. + * You specify the rectangle and the density of sample points. + * The result is a single tilted plane. Best for a flat bed. + * + * - AUTO_BED_LEVELING_BILINEAR + * Probe several points in a grid. + * You specify the rectangle and the density of sample points. + * The result is a mesh, best for large or uneven beds. + * + * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling) + * A comprehensive bed leveling system combining the features and benefits + * of other systems. UBL also includes integrated Mesh Generation, Mesh + * Validation and Mesh Editing systems. + * + * - MESH_BED_LEVELING + * Probe a grid manually + * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.) + * For machines without a probe, Mesh Bed Leveling provides a method to perform + * leveling in steps so you can manually adjust the Z height at each grid-point. + * With an LCD controller the process is guided step-by-step. + */ +//#define AUTO_BED_LEVELING_3POINT +//#define AUTO_BED_LEVELING_LINEAR +//#define AUTO_BED_LEVELING_BILINEAR +//#define AUTO_BED_LEVELING_UBL +//#define MESH_BED_LEVELING + +/** + * Normally G28 leaves leveling disabled on completion. Enable + * this option to have G28 restore the prior leveling state. + */ +//#define RESTORE_LEVELING_AFTER_G28 + +/** + * Enable detailed logging of G28, G29, M48, etc. + * Turn on with the command 'M111 S32'. + * NOTE: Requires a lot of PROGMEM! + */ +//#define DEBUG_LEVELING_FEATURE + +#if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_BILINEAR, AUTO_BED_LEVELING_UBL) + // Gradually reduce leveling correction until a set height is reached, + // at which point movement will be level to the machine's XY plane. + // The height can be set with M420 Z + #define ENABLE_LEVELING_FADE_HEIGHT + + // For Cartesian machines, instead of dividing moves on mesh boundaries, + // split up moves into short segments like a Delta. This follows the + // contours of the bed more closely than edge-to-edge straight moves. + #define SEGMENT_LEVELED_MOVES + #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one) + + /** + * Enable the G26 Mesh Validation Pattern tool. + */ + //#define G26_MESH_VALIDATION + #if ENABLED(G26_MESH_VALIDATION) + #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle. + #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool. + #define MESH_TEST_HOTEND_TEMP 205 // (°C) Default nozzle temperature for the G26 Mesh Validation Tool. + #define MESH_TEST_BED_TEMP 60 // (°C) Default bed temperature for the G26 Mesh Validation Tool. + #define G26_XY_FEEDRATE 20 // (mm/s) Feedrate for XY Moves for the G26 Mesh Validation Tool. + #endif + +#endif + +#if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR) + + // Set the number of grid points per dimension. + #define GRID_MAX_POINTS_X 3 + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + // Set the boundaries for probing (where the probe can reach). + //#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE + //#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE)) + //#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE + //#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE)) + + // Probe along the Y axis, advancing X after each column + //#define PROBE_Y_FIRST + + #if ENABLED(AUTO_BED_LEVELING_BILINEAR) + + // Beyond the probed grid, continue the implied tilt? + // Default is to maintain the height of the nearest edge. + //#define EXTRAPOLATE_BEYOND_GRID + + // + // Experimental Subdivision of the grid by Catmull-Rom method. + // Synthesizes intermediate points to produce a more detailed mesh. + // + //#define ABL_BILINEAR_SUBDIVISION + #if ENABLED(ABL_BILINEAR_SUBDIVISION) + // Number of subdivisions between probe points + #define BILINEAR_SUBDIVISIONS 3 + #endif + + #endif + +#elif ENABLED(AUTO_BED_LEVELING_UBL) + + //=========================================================================== + //========================= Unified Bed Leveling ============================ + //=========================================================================== + + //#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh + + #define MESH_INSET 1 // Set Mesh bounds as an inset region of the bed + #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited. + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + #define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle + #define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500 + + //#define UBL_Z_RAISE_WHEN_OFF_MESH 2.5 // When the nozzle is off the mesh, this value is used + // as the Z-Height correction value. + +#elif ENABLED(MESH_BED_LEVELING) + + //=========================================================================== + //=================================== Mesh ================================== + //=========================================================================== + + #define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed + #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited. + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS + +#endif // BED_LEVELING + +/** + * Points to probe for all 3-point Leveling procedures. + * Override if the automatically selected points are inadequate. + */ +#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL) + //#define PROBE_PT_1_X 15 + //#define PROBE_PT_1_Y 180 + //#define PROBE_PT_2_X 15 + //#define PROBE_PT_2_Y 20 + //#define PROBE_PT_3_X 170 + //#define PROBE_PT_3_Y 20 +#endif + +/** + * Add a bed leveling sub-menu for ABL or MBL. + * Include a guided procedure if manual probing is enabled. + */ +//#define LCD_BED_LEVELING + +#if ENABLED(LCD_BED_LEVELING) + #define MESH_EDIT_Z_STEP 0.025 // (mm) Step size while manually probing Z axis. + #define LCD_PROBE_Z_RANGE 4 // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment + //#define MESH_EDIT_MENU // Add a menu to edit mesh points +#endif + +// Add a menu item to move between bed corners for manual bed adjustment +//#define LEVEL_BED_CORNERS + +#if ENABLED(LEVEL_BED_CORNERS) + #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner +#endif + +/** + * Commands to execute at the end of G29 probing. + * Useful to retract or move the Z probe out of the way. + */ +//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" + + +// @section homing + +// The center of the bed is at (X=0, Y=0) +//#define BED_CENTER_AT_0_0 + +// Manually set the home position. Leave these undefined for automatic settings. +// For DELTA this is the top-center of the Cartesian print volume. +//#define MANUAL_X_HOME_POS 0 +//#define MANUAL_Y_HOME_POS 0 +//#define MANUAL_Z_HOME_POS 0 + +// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area. +// +// With this feature enabled: +// +// - Allow Z homing only after X and Y homing AND stepper drivers still enabled. +// - If stepper drivers time out, it will need X and Y homing again before Z homing. +// - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28). +// - Prevent Z homing when the Z probe is outside bed area. +// +#define Z_SAFE_HOMING + +#if ENABLED(Z_SAFE_HOMING) + #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing when homing all axes (G28). + #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2) // Y point for Z homing when homing all axes (G28). +#endif + +// Homing speeds (mm/m) +#define HOMING_FEEDRATE_XY (50*60) +#define HOMING_FEEDRATE_Z (4*60) + +// Validate that endstops are triggered on homing moves +#define VALIDATE_HOMING_ENDSTOPS + +// @section calibrate + +/** + * Bed Skew Compensation + * + * This feature corrects for misalignment in the XYZ axes. + * + * Take the following steps to get the bed skew in the XY plane: + * 1. Print a test square (e.g., https://www.thingiverse.com/thing:2563185) + * 2. For XY_DIAG_AC measure the diagonal A to C + * 3. For XY_DIAG_BD measure the diagonal B to D + * 4. For XY_SIDE_AD measure the edge A to D + * + * Marlin automatically computes skew factors from these measurements. + * Skew factors may also be computed and set manually: + * + * - Compute AB : SQRT(2*AC*AC+2*BD*BD-4*AD*AD)/2 + * - XY_SKEW_FACTOR : TAN(PI/2-ACOS((AC*AC-AB*AB-AD*AD)/(2*AB*AD))) + * + * If desired, follow the same procedure for XZ and YZ. + * Use these diagrams for reference: + * + * Y Z Z + * ^ B-------C ^ B-------C ^ B-------C + * | / / | / / | / / + * | / / | / / | / / + * | A-------D | A-------D | A-------D + * +-------------->X +-------------->X +-------------->Y + * XY_SKEW_FACTOR XZ_SKEW_FACTOR YZ_SKEW_FACTOR + */ +//#define SKEW_CORRECTION + +#if ENABLED(SKEW_CORRECTION) + // Input all length measurements here: + #define XY_DIAG_AC 282.8427124746 + #define XY_DIAG_BD 282.8427124746 + #define XY_SIDE_AD 200 + + // Or, set the default skew factors directly here + // to override the above measurements: + #define XY_SKEW_FACTOR 0.0 + + //#define SKEW_CORRECTION_FOR_Z + #if ENABLED(SKEW_CORRECTION_FOR_Z) + #define XZ_DIAG_AC 282.8427124746 + #define XZ_DIAG_BD 282.8427124746 + #define YZ_DIAG_AC 282.8427124746 + #define YZ_DIAG_BD 282.8427124746 + #define YZ_SIDE_AD 200 + #define XZ_SKEW_FACTOR 0.0 + #define YZ_SKEW_FACTOR 0.0 + #endif + + // Enable this option for M852 to set skew at runtime + //#define SKEW_CORRECTION_GCODE +#endif + +//============================================================================= +//============================= Additional Features =========================== +//============================================================================= + +// @section extras + +/** + * EEPROM + * + * Persistent storage to preserve configurable settings across reboots. + * + * M500 - Store settings to EEPROM. + * M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes) + * M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.) + */ +#define EEPROM_SETTINGS // Persistent storage with M500 and M501 +//#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release! +#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM. +#if ENABLED(EEPROM_SETTINGS) + //#define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors. +#endif + +// +// Host Keepalive +// +// When enabled Marlin will send a busy status message to the host +// every couple of seconds when it can't accept commands. +// +#define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages +#define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113. +#define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating + +// +// M100 Free Memory Watcher +// +//#define M100_FREE_MEMORY_WATCHER // Add M100 (Free Memory Watcher) to debug memory usage + +// +// G20/G21 Inch mode support +// +//#define INCH_MODE_SUPPORT + +// +// M149 Set temperature units support +// +//#define TEMPERATURE_UNITS_SUPPORT + +// @section temperature + +// Preheat Constants +#define PREHEAT_1_LABEL "PLA" +#define PREHEAT_1_TEMP_HOTEND 180 +#define PREHEAT_1_TEMP_BED 70 +#define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255 + +#define PREHEAT_2_LABEL "ABS" +#define PREHEAT_2_TEMP_HOTEND 240 +#define PREHEAT_2_TEMP_BED 110 +#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255 + +/** + * Nozzle Park + * + * Park the nozzle at the given XYZ position on idle or G27. + * + * The "P" parameter controls the action applied to the Z axis: + * + * P0 (Default) If Z is below park Z raise the nozzle. + * P1 Raise the nozzle always to Z-park height. + * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS. + */ +//#define NOZZLE_PARK_FEATURE + +#if ENABLED(NOZZLE_PARK_FEATURE) + // Specify a park position as { X, Y, Z_raise } + #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 } + #define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis) + #define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers) +#endif + +/** + * Clean Nozzle Feature -- EXPERIMENTAL + * + * Adds the G12 command to perform a nozzle cleaning process. + * + * Parameters: + * P Pattern + * S Strokes / Repetitions + * T Triangles (P1 only) + * + * Patterns: + * P0 Straight line (default). This process requires a sponge type material + * at a fixed bed location. "S" specifies strokes (i.e. back-forth motions) + * between the start / end points. + * + * P1 Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the + * number of zig-zag triangles to do. "S" defines the number of strokes. + * Zig-zags are done in whichever is the narrower dimension. + * For example, "G12 P1 S1 T3" will execute: + * + * -- + * | (X0, Y1) | /\ /\ /\ | (X1, Y1) + * | | / \ / \ / \ | + * A | | / \ / \ / \ | + * | | / \ / \ / \ | + * | (X0, Y0) | / \/ \/ \ | (X1, Y0) + * -- +--------------------------------+ + * |________|_________|_________| + * T1 T2 T3 + * + * P2 Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE. + * "R" specifies the radius. "S" specifies the stroke count. + * Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT. + * + * Caveats: The ending Z should be the same as starting Z. + * Attention: EXPERIMENTAL. G-code arguments may change. + * + */ +//#define NOZZLE_CLEAN_FEATURE + +#if ENABLED(NOZZLE_CLEAN_FEATURE) + // Default number of pattern repetitions + #define NOZZLE_CLEAN_STROKES 12 + + // Default number of triangles + #define NOZZLE_CLEAN_TRIANGLES 3 + + // Specify positions as { X, Y, Z } + #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)} + #define NOZZLE_CLEAN_END_POINT { 100, 60, (Z_MIN_POS + 1) } + + // Circular pattern radius + #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5 + // Circular pattern circle fragments number + #define NOZZLE_CLEAN_CIRCLE_FN 10 + // Middle point of circle + #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT + + // Move the nozzle to the initial position after cleaning + #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z +#endif + +/** + * Print Job Timer + * + * Automatically start and stop the print job timer on M104/M109/M190. + * + * M104 (hotend, no wait) - high temp = none, low temp = stop timer + * M109 (hotend, wait) - high temp = start timer, low temp = stop timer + * M190 (bed, wait) - high temp = start timer, low temp = none + * + * The timer can also be controlled with the following commands: + * + * M75 - Start the print job timer + * M76 - Pause the print job timer + * M77 - Stop the print job timer + */ +#define PRINTJOB_TIMER_AUTOSTART + +/** + * Print Counter + * + * Track statistical data such as: + * + * - Total print jobs + * - Total successful print jobs + * - Total failed print jobs + * - Total time printing + * + * View the current statistics with M78. + */ +//#define PRINTCOUNTER + +//============================================================================= +//============================= LCD and SD support ============================ +//============================================================================= + +// @section lcd + +/** + * LCD LANGUAGE + * + * Select the language to display on the LCD. These languages are available: + * + * en, an, bg, ca, cz, da, de, el, el-gr, es, eu, fi, fr, gl, hr, it, + * jp-kana, ko_KR, nl, pl, pt, pt-br, ru, sk, tr, uk, zh_CN, zh_TW, test + * + * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cz':'Czech', 'da':'Danish', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'jp-kana':'Japanese', 'ko_KR':'Korean (South Korea)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'ru':'Russian', 'sk':'Slovak', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Traditional)', 'test':'TEST' } + */ +#define LCD_LANGUAGE en + +/** + * LCD Character Set + * + * Note: This option is NOT applicable to Graphical Displays. + * + * All character-based LCDs provide ASCII plus one of these + * language extensions: + * + * - JAPANESE ... the most common + * - WESTERN ... with more accented characters + * - CYRILLIC ... for the Russian language + * + * To determine the language extension installed on your controller: + * + * - Compile and upload with LCD_LANGUAGE set to 'test' + * - Click the controller to view the LCD menu + * - The LCD will display Japanese, Western, or Cyrillic text + * + * See http://marlinfw.org/docs/development/lcd_language.html + * + * :['JAPANESE', 'WESTERN', 'CYRILLIC'] + */ +#define DISPLAY_CHARSET_HD44780 JAPANESE + +/** + * Info Screen Style (0:Classic, 1:Prusa) + * + * :[0:'Classic', 1:'Prusa'] + */ +#define LCD_INFO_SCREEN_STYLE 0 + +/** + * SD CARD + * + * SD Card support is disabled by default. If your controller has an SD slot, + * you must uncomment the following option or it won't work. + * + */ +#define SDSUPPORT + +/** + * SD CARD: SPI SPEED + * + * Enable one of the following items for a slower SPI transfer speed. + * This may be required to resolve "volume init" errors. + */ +//#define SPI_SPEED SPI_HALF_SPEED +//#define SPI_SPEED SPI_QUARTER_SPEED +//#define SPI_SPEED SPI_EIGHTH_SPEED + +/** + * SD CARD: ENABLE CRC + * + * Use CRC checks and retries on the SD communication. + */ +//#define SD_CHECK_AND_RETRY + +/** + * LCD Menu Items + * + * Disable all menus and only display the Status Screen, or + * just remove some extraneous menu items to recover space. + */ +//#define NO_LCD_MENUS +//#define SLIM_LCD_MENUS + +// +// ENCODER SETTINGS +// +// This option overrides the default number of encoder pulses needed to +// produce one step. Should be increased for high-resolution encoders. +// +//#define ENCODER_PULSES_PER_STEP 4 + +// +// Use this option to override the number of step signals required to +// move between next/prev menu items. +// +//#define ENCODER_STEPS_PER_MENU_ITEM 1 + +/** + * Encoder Direction Options + * + * Test your encoder's behavior first with both options disabled. + * + * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION. + * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION. + * Reversed Value Editing only? Enable BOTH options. + */ + +// +// This option reverses the encoder direction everywhere. +// +// Set this option if CLOCKWISE causes values to DECREASE +// +//#define REVERSE_ENCODER_DIRECTION + +// +// This option reverses the encoder direction for navigating LCD menus. +// +// If CLOCKWISE normally moves DOWN this makes it go UP. +// If CLOCKWISE normally moves UP this makes it go DOWN. +// +//#define REVERSE_MENU_DIRECTION + +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + +// +// Individual Axis Homing +// +// Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu. +// +//#define INDIVIDUAL_AXIS_HOMING_MENU + +// +// SPEAKER/BUZZER +// +// If you have a speaker that can produce tones, enable it here. +// By default Marlin assumes you have a buzzer with a fixed frequency. +// +//#define SPEAKER + +// +// The duration and frequency for the UI feedback sound. +// Set these to 0 to disable audio feedback in the LCD menus. +// +// Note: Test audio output with the G-Code: +// M300 S P +// +//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 2 +//#define LCD_FEEDBACK_FREQUENCY_HZ 5000 + +//============================================================================= +//======================== LCD / Controller Selection ========================= +//======================== (Character-based LCDs) ========================= +//============================================================================= + +// +// RepRapDiscount Smart Controller. +// http://reprap.org/wiki/RepRapDiscount_Smart_Controller +// +// Note: Usually sold with a white PCB. +// +//#define REPRAP_DISCOUNT_SMART_CONTROLLER + +// +// Original RADDS LCD Display+Encoder+SDCardReader +// http://doku.radds.org/dokumentation/lcd-display/ +// +//#define RADDS_DISPLAY + +// +// ULTIMAKER Controller. +// +//#define ULTIMAKERCONTROLLER + +// +// ULTIPANEL as seen on Thingiverse. +// +//#define ULTIPANEL + +// +// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3) +// http://reprap.org/wiki/PanelOne +// +//#define PANEL_ONE + +// +// GADGETS3D G3D LCD/SD Controller +// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel +// +// Note: Usually sold with a blue PCB. +// +//#define G3D_PANEL + +// +// RigidBot Panel V1.0 +// http://www.inventapart.com/ +// +//#define RIGIDBOT_PANEL + +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// ANET and Tronxy 20x4 Controller +// +//#define ZONESTAR_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin. + // This LCD is known to be susceptible to electrical interference + // which scrambles the display. Pressing any button clears it up. + // This is a LCD2004 display with 5 analog buttons. + +// +// Generic 16x2, 16x4, 20x2, or 20x4 character-based LCD. +// +//#define ULTRA_LCD + +//============================================================================= +//======================== LCD / Controller Selection ========================= +//===================== (I2C and Shift-Register LCDs) ===================== +//============================================================================= + +// +// CONTROLLER TYPE: I2C +// +// Note: These controllers require the installation of Arduino's LiquidCrystal_I2C +// library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C +// + +// +// Elefu RA Board Control Panel +// http://www.elefu.com/index.php?route=product/product&product_id=53 +// +//#define RA_CONTROL_PANEL + +// +// Sainsmart (YwRobot) LCD Displays +// +// These require F.Malpartida's LiquidCrystal_I2C library +// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home +// +//#define LCD_SAINSMART_I2C_1602 +//#define LCD_SAINSMART_I2C_2004 + +// +// Generic LCM1602 LCD adapter +// +//#define LCM1602 + +// +// PANELOLU2 LCD with status LEDs, +// separate encoder and click inputs. +// +// Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later. +// For more info: https://github.com/lincomatic/LiquidTWI2 +// +// Note: The PANELOLU2 encoder click input can either be directly connected to +// a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1). +// +//#define LCD_I2C_PANELOLU2 + +// +// Panucatt VIKI LCD with status LEDs, +// integrated click & L/R/U/D buttons, separate encoder inputs. +// +//#define LCD_I2C_VIKI + +// +// CONTROLLER TYPE: Shift register panels +// + +// +// 2-wire Non-latching LCD SR from https://goo.gl/aJJ4sH +// LCD configuration: http://reprap.org/wiki/SAV_3D_LCD +// +//#define SAV_3DLCD + +// +// 3-wire SR LCD with strobe using 74HC4094 +// https://github.com/mikeshub/SailfishLCD +// Uses the code directly from Sailfish +// +//#define FF_INTERFACEBOARD + +//============================================================================= +//======================= LCD / Controller Selection ======================= +//========================= (Graphical LCDs) ======================== +//============================================================================= + +// +// CONTROLLER TYPE: Graphical 128x64 (DOGM) +// +// IMPORTANT: The U8glib library is required for Graphical Display! +// https://github.com/olikraus/U8glib_Arduino +// + +// +// RepRapDiscount FULL GRAPHIC Smart Controller +// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller +// +#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER + +// +// ReprapWorld Graphical LCD +// https://reprapworld.com/?products_details&products_id/1218 +// +//#define REPRAPWORLD_GRAPHICAL_LCD + +// +// Activate one of these if you have a Panucatt Devices +// Viki 2.0 or mini Viki with Graphic LCD +// http://panucatt.com +// +//#define VIKI2 +//#define miniVIKI + +// +// MakerLab Mini Panel with graphic +// controller and SD support - http://reprap.org/wiki/Mini_panel +// +//#define MINIPANEL + +// +// MaKr3d Makr-Panel with graphic controller and SD support. +// http://reprap.org/wiki/MaKr3d_MaKrPanel +// +//#define MAKRPANEL + +// +// Adafruit ST7565 Full Graphic Controller. +// https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/ +// +//#define ELB_FULL_GRAPHIC_CONTROLLER + +// +// BQ LCD Smart Controller shipped by +// default with the BQ Hephestos 2 and Witbox 2. +// +//#define BQ_LCD_SMART_CONTROLLER + +// +// Cartesio UI +// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// +//#define CARTESIO_UI + +// +// LCD for Melzi Card with Graphical LCD +// +//#define LCD_FOR_MELZI + +// +// Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder +// https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) +// +//#define ULTI_CONTROLLER + +// +// MKS MINI12864 with graphic controller and SD support +// https://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// FYSETC variant of the MINI12864 graphic controller with SD support +// https://wiki.fysetc.com/Mini12864_Panel/ +// +//#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default +//#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) +//#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// ANET and Tronxy Graphical Controller +// +// Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6 +// A clone of the RepRapDiscount full graphics display but with +// different pins/wiring (see pins_ANET_10.h). +// +//#define ANET_FULL_GRAPHICS_LCD + +// +// AZSMZ 12864 LCD with SD +// https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html +// +//#define AZSMZ_12864 + +// +// Silvergate GLCD controller +// http://github.com/android444/Silvergate +// +//#define SILVER_GATE_GLCD_CONTROLLER + +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + +//============================================================================= +//========================== Extensible UI Displays =========================== +//============================================================================= + +// +// DGUS Touch Display with DWIN OS +// +//#define DGUS_LCD + +// +// Touch-screen LCD for Malyan M200 printers +// +//#define MALYAN_LCD + +// +// Third-party or vendor-customized controller interfaces. +// Sources should be installed in 'src/lcd/extensible_ui'. +// +//#define EXTENSIBLE_UI + +//============================================================================= +//=============================== Graphical TFTs ============================== +//============================================================================= + +// +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) +// +//#define FSMC_GRAPHICAL_TFT + +//============================================================================= +//============================ Other Controllers ============================ +//============================================================================= + +// +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 +// +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif + +// +// RepRapWorld REPRAPWORLD_KEYPAD v1.1 +// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626 +// +// REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key +// is pressed, a value of 10.0 means 10mm per click. +// +//#define REPRAPWORLD_KEYPAD +//#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 + +//============================================================================= +//=============================== Extra Features ============================== +//============================================================================= + +// @section extras + +// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino +//#define FAST_PWM_FAN + +// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency +// which is not as annoying as with the hardware PWM. On the other hand, if this frequency +// is too low, you should also increment SOFT_PWM_SCALE. +//#define FAN_SOFT_PWM + +// Incrementing this by 1 will double the software PWM frequency, +// affecting heaters, and the fan if FAN_SOFT_PWM is enabled. +// However, control resolution will be halved for each increment; +// at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] +#define SOFT_PWM_SCALE 0 + +// If SOFT_PWM_SCALE is set to a value higher than 0, dithering can +// be used to mitigate the associated resolution loss. If enabled, +// some of the PWM cycles are stretched so on average the desired +// duty cycle is attained. +//#define SOFT_PWM_DITHER + +// Temperature status LEDs that display the hotend and bed temperature. +// If all hotends, bed temperature, and target temperature are under 54C +// then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis) +//#define TEMP_STAT_LEDS + +// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure +//#define SF_ARC_FIX + +// Support for the BariCUDA Paste Extruder +//#define BARICUDA + +// Support for BlinkM/CyzRgb +//#define BLINKM + +// Support for PCA9632 PWM LED driver +//#define PCA9632 + +// Support for PCA9533 PWM LED driver +// https://github.com/mikeshub/SailfishRGB_LED +//#define PCA9533 + +/** + * RGB LED / LED Strip Control + * + * Enable support for an RGB LED connected to 5V digital pins, or + * an RGB Strip connected to MOSFETs controlled by digital pins. + * + * Adds the M150 command to set the LED (or LED strip) color. + * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of + * luminance values can be set from 0 to 255. + * For Neopixel LED an overall brightness parameter is also available. + * + * *** CAUTION *** + * LED Strips require a MOSFET Chip between PWM lines and LEDs, + * as the Arduino cannot handle the current the LEDs will require. + * Failure to follow this precaution can destroy your Arduino! + * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * more current than the Arduino 5V linear regulator can produce. + * *** CAUTION *** + * + * LED Type. Enable only one of the following two options. + * + */ +#define RGB_LED +//#define RGBW_LED + +#if EITHER(RGB_LED, RGBW_LED) + //#define RGB_LED_R_PIN 34 + //#define RGB_LED_G_PIN 43 + //#define RGB_LED_B_PIN 35 + //#define RGB_LED_W_PIN -1 +#endif + +// Support for Adafruit Neopixel LED driver +//#define NEOPIXEL_LED +#if ENABLED(NEOPIXEL_LED) + #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. + #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) + //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup + + // Use a single Neopixel LED for static (background) lighting + //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use + //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W +#endif + +/** + * Printer Event LEDs + * + * During printing, the LEDs will reflect the printer status: + * + * - Gradually change from blue to violet as the heated bed gets to target temp + * - Gradually change from violet to red as the hotend gets to temperature + * - Change to white to illuminate work surface + * - Change to green once print has finished + * - Turn off after the print has finished and the user has pushed a button + */ +#if ANY(BLINKM, RGB_LED, RGBW_LED, PCA9632, PCA9533, NEOPIXEL_LED) + #define PRINTER_EVENT_LEDS +#endif + +/** + * R/C SERVO support + * Sponsored by TrinityLabs, Reworked by codexmas + */ + +/** + * Number of servos + * + * For some servo-related options NUM_SERVOS will be set automatically. + * Set this manually if there are extra servos needing manual control. + * Leave undefined or set to 0 to entirely disable the servo subsystem. + */ +//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command + +// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. +// 300ms is a good value but you can try less delay. +// If the servo can't reach the requested position, increase it. +#define SERVO_DELAY { 300 } + +// Only power servos during movement, otherwise leave off to prevent jitter +//#define DEACTIVATE_SERVOS_AFTER_MOVE + +// Allow servo angle to be edited and saved to EEPROM +//#define EDITABLE_SERVO_ANGLES + +/** + * Sometimes after inserting the SD card settings get lost. + * This option reloads settings when the SD card is inserted. + */ +#define SD_RELOAD_SETTINGS diff --git a/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h b/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h new file mode 100644 index 0000000000..9e391d1733 --- /dev/null +++ b/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h @@ -0,0 +1,2562 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Configuration_adv.h + * + * Advanced settings. + * Only change these if you know exactly what you're doing. + * Some of these settings can damage your printer if improperly set! + * + * Basic settings can be found in Configuration.h + * + */ +#define CONFIGURATION_ADV_H_VERSION 020000 + +// @section temperature + +//=========================================================================== +//=============================Thermal Settings ============================ +//=========================================================================== + +// +// Custom Thermistor 1000 parameters +// +#if TEMP_SENSOR_0 == 1000 + #define HOTEND0_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND0_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND0_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_1 == 1000 + #define HOTEND1_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND1_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND1_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_2 == 1000 + #define HOTEND2_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND2_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND2_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_3 == 1000 + #define HOTEND3_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND3_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND3_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_4 == 1000 + #define HOTEND4_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND4_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND4_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_5 == 1000 + #define HOTEND5_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND5_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND5_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_BED == 1000 + #define BED_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define BED_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define BED_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_CHAMBER == 1000 + #define CHAMBER_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define CHAMBER_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define CHAMBER_BETA 3950 // Beta value +#endif + +// +// Hephestos 2 24V heated bed upgrade kit. +// https://store.bq.com/en/heated-bed-kit-hephestos2 +// +//#define HEPHESTOS2_HEATED_BED_KIT +#if ENABLED(HEPHESTOS2_HEATED_BED_KIT) + #undef TEMP_SENSOR_BED + #define TEMP_SENSOR_BED 70 + #define HEATER_BED_INVERTING true +#endif + +/** + * Heated Chamber settings + */ +#if TEMP_SENSOR_CHAMBER + #define CHAMBER_MINTEMP 5 + #define CHAMBER_MAXTEMP 60 + #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target + //#define CHAMBER_LIMIT_SWITCHING + //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin + //#define HEATER_CHAMBER_INVERTING false +#endif + +#if DISABLED(PIDTEMPBED) + #define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control + #if ENABLED(BED_LIMIT_SWITCHING) + #define BED_HYSTERESIS 2 // Only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS + #endif +#endif + +/** + * Thermal Protection provides additional protection to your printer from damage + * and fire. Marlin always includes safe min and max temperature ranges which + * protect against a broken or disconnected thermistor wire. + * + * The issue: If a thermistor falls out, it will report the much lower + * temperature of the air in the room, and the the firmware will keep + * the heater on. + * + * The solution: Once the temperature reaches the target, start observing. + * If the temperature stays too far below the target (hysteresis) for too + * long (period), the firmware will halt the machine as a safety precaution. + * + * If you get false positives for "Thermal Runaway", increase + * THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD + */ +#if ENABLED(THERMAL_PROTECTION_HOTENDS) + #define THERMAL_PROTECTION_PERIOD 40 // Seconds + #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius + + //#define ADAPTIVE_FAN_SLOWING // Slow part cooling fan if temperature drops + #if BOTH(ADAPTIVE_FAN_SLOWING, PIDTEMP) + //#define NO_FAN_SLOWING_IN_PID_TUNING // Don't slow fan speed during M303 + #endif + + /** + * Whenever an M104, M109, or M303 increases the target temperature, the + * firmware will wait for the WATCH_TEMP_PERIOD to expire. If the temperature + * hasn't increased by WATCH_TEMP_INCREASE degrees, the machine is halted and + * requires a hard reset. This test restarts with any M104/M109/M303, but only + * if the current temperature is far enough below the target for a reliable + * test. + * + * If you get false positives for "Heating failed", increase WATCH_TEMP_PERIOD + * and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set + * below 2. + */ + #define WATCH_TEMP_PERIOD 120 // Seconds + #define WATCH_TEMP_INCREASE 2 // Degrees Celsius +#endif + +/** + * Thermal Protection parameters for the bed are just as above for hotends. + */ +#if ENABLED(THERMAL_PROTECTION_BED) + #define THERMAL_PROTECTION_BED_PERIOD 60 // Seconds + #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius + + /** + * As described above, except for the bed (M140/M190/M303). + */ + #define WATCH_BED_TEMP_PERIOD 100 // Seconds + #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius +#endif + +/** + * Thermal Protection parameters for the heated chamber. + */ +#if ENABLED(THERMAL_PROTECTION_CHAMBER) + #define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds + #define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius + + /** + * Heated chamber watch settings (M141/M191). + */ + #define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds + #define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius +#endif + +#if ENABLED(PIDTEMP) + // Add an experimental additional term to the heater power, proportional to the extrusion speed. + // A well-chosen Kc value should add just enough power to melt the increased material volume. + //#define PID_EXTRUSION_SCALING + #if ENABLED(PID_EXTRUSION_SCALING) + #define DEFAULT_Kc (100) //heating power=Kc*(e_speed) + #define LPQ_MAX_LEN 50 + #endif +#endif + +/** + * Automatic Temperature: + * The hotend target temperature is calculated by all the buffered lines of gcode. + * The maximum buffered steps/sec of the extruder motor is called "se". + * Start autotemp mode with M109 S B F + * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by + * mintemp and maxtemp. Turn this off by executing M109 without F* + * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp. + * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode + */ +#define AUTOTEMP +#if ENABLED(AUTOTEMP) + #define AUTOTEMP_OLDWEIGHT 0.98 +#endif + +// Show extra position information in M114 +//#define M114_DETAIL + +// Show Temperature ADC value +// Enable for M105 to include ADC values read from temperature sensors. +//#define SHOW_TEMP_ADC_VALUES + +/** + * High Temperature Thermistor Support + * + * Thermistors able to support high temperature tend to have a hard time getting + * good readings at room and lower temperatures. This means HEATER_X_RAW_LO_TEMP + * will probably be caught when the heating element first turns on during the + * preheating process, which will trigger a min_temp_error as a safety measure + * and force stop everything. + * To circumvent this limitation, we allow for a preheat time (during which, + * min_temp_error won't be triggered) and add a min_temp buffer to handle + * aberrant readings. + * + * If you want to enable this feature for your hotend thermistor(s) + * uncomment and set values > 0 in the constants below + */ + +// The number of consecutive low temperature errors that can occur +// before a min_temp_error is triggered. (Shouldn't be more than 10.) +//#define MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED 0 + +// The number of milliseconds a hotend will preheat before starting to check +// the temperature. This value should NOT be set to the time it takes the +// hot end to reach the target temperature, but the time it takes to reach +// the minimum temperature your thermistor can read. The lower the better/safer. +// This shouldn't need to be more than 30 seconds (30000) +//#define MILLISECONDS_PREHEAT_TIME 0 + +// @section extruder + +// Extruder runout prevention. +// If the machine is idle and the temperature over MINTEMP +// then extrude some filament every couple of SECONDS. +//#define EXTRUDER_RUNOUT_PREVENT +#if ENABLED(EXTRUDER_RUNOUT_PREVENT) + #define EXTRUDER_RUNOUT_MINTEMP 190 + #define EXTRUDER_RUNOUT_SECONDS 30 + #define EXTRUDER_RUNOUT_SPEED 1500 // (mm/m) + #define EXTRUDER_RUNOUT_EXTRUDE 5 // (mm) +#endif + +// @section temperature + +// Calibration for AD595 / AD8495 sensor to adjust temperature measurements. +// The final temperature is calculated as (measuredTemp * GAIN) + OFFSET. +#define TEMP_SENSOR_AD595_OFFSET 0.0 +#define TEMP_SENSOR_AD595_GAIN 1.0 +#define TEMP_SENSOR_AD8495_OFFSET 0.0 +#define TEMP_SENSOR_AD8495_GAIN 1.0 + +/** + * Controller Fan + * To cool down the stepper drivers and MOSFETs. + * + * The fan will turn on automatically whenever any stepper is enabled + * and turn off after a set period after all steppers are turned off. + */ +//#define USE_CONTROLLER_FAN +#if ENABLED(USE_CONTROLLER_FAN) + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled + #define CONTROLLERFAN_SPEED 255 // 255 == full speed +#endif + +// When first starting the main fan, run it at full speed for the +// given number of milliseconds. This gets the fan spinning reliably +// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) +//#define FAN_KICKSTART_TIME 100 + +/** + * PWM Fan Scaling + * + * Define the min/max speeds for PWM fans (as set with M106). + * + * With these options the M106 0-255 value range is scaled to a subset + * to ensure that the fan has enough power to spin, or to run lower + * current fans with higher current. (e.g., 5V/12V fans with 12V/24V) + * Value 0 always turns off the fan. + * + * Define one or both of these to override the default 0-255 range. + */ +//#define FAN_MIN_PWM 50 +//#define FAN_MAX_PWM 128 + +/** + * FAST PWM FAN Settings + * + * Use to change the FAST FAN PWM frequency (if enabled in Configuration.h) + * Combinations of PWM Modes, prescale values and TOP resolutions are used internally to produce a + * frequency as close as possible to the desired frequency. + * + * FAST_PWM_FAN_FREQUENCY [undefined by default] + * Set this to your desired frequency. + * If left undefined this defaults to F = F_CPU/(2*255*1) + * ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers + * These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required + * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior. + * + * USE_OCR2A_AS_TOP [undefined by default] + * Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2: + * 16MHz MCUs: [62.5KHz, 31.4KHz (default), 7.8KHz, 3.92KHz, 1.95KHz, 977Hz, 488Hz, 244Hz, 60Hz, 122Hz, 30Hz] + * 20MHz MCUs: [78.1KHz, 39.2KHz (default), 9.77KHz, 4.9KHz, 2.44KHz, 1.22KHz, 610Hz, 305Hz, 153Hz, 76Hz, 38Hz] + * A greater range can be achieved by enabling USE_OCR2A_AS_TOP. But note that this option blocks the use of + * PWM on pin OC2A. Only use this option if you don't need PWM on 0C2A. (Check your schematic.) + * USE_OCR2A_AS_TOP sacrifices duty cycle control resolution to achieve this broader range of frequencies. + */ +#if ENABLED(FAST_PWM_FAN) + //#define FAST_PWM_FAN_FREQUENCY 31400 + //#define USE_OCR2A_AS_TOP +#endif + +// @section extruder + +/** + * Extruder cooling fans + * + * Extruder auto fans automatically turn on when their extruders' + * temperatures go above EXTRUDER_AUTO_FAN_TEMPERATURE. + * + * Your board's pins file specifies the recommended pins. Override those here + * or set to -1 to disable completely. + * + * Multiple extruders can be assigned to the same pin in which case + * the fan will turn on when any selected extruder is above the threshold. + */ +#define E0_AUTO_FAN_PIN -1 +#define E1_AUTO_FAN_PIN -1 +#define E2_AUTO_FAN_PIN -1 +#define E3_AUTO_FAN_PIN -1 +#define E4_AUTO_FAN_PIN -1 +#define E5_AUTO_FAN_PIN -1 +#define CHAMBER_AUTO_FAN_PIN -1 + +#define EXTRUDER_AUTO_FAN_TEMPERATURE 50 +#define EXTRUDER_AUTO_FAN_SPEED 255 // 255 == full speed +#define CHAMBER_AUTO_FAN_TEMPERATURE 30 +#define CHAMBER_AUTO_FAN_SPEED 255 + +/** + * Part-Cooling Fan Multiplexer + * + * This feature allows you to digitally multiplex the fan output. + * The multiplexer is automatically switched at tool-change. + * Set FANMUX[012]_PINs below for up to 2, 4, or 8 multiplexed fans. + */ +#define FANMUX0_PIN -1 +#define FANMUX1_PIN -1 +#define FANMUX2_PIN -1 + +/** + * M355 Case Light on-off / brightness + */ +//#define CASE_LIGHT_ENABLE +#if ENABLED(CASE_LIGHT_ENABLE) + //#define CASE_LIGHT_PIN 4 // Override the default pin if needed + #define INVERT_CASE_LIGHT false // Set true if Case Light is ON when pin is LOW + #define CASE_LIGHT_DEFAULT_ON true // Set default power-up state on + #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105 // Set default power-up brightness (0-255, requires PWM pin) + //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu + //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. + //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) + #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } + #endif +#endif + +// @section homing + +// If you want endstops to stay on (by default) even when not homing +// enable this option. Override at any time with M120, M121. +//#define ENDSTOPS_ALWAYS_ON_DEFAULT + +// @section extras + +//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats. + +// Employ an external closed loop controller. Override pins here if needed. +//#define EXTERNAL_CLOSED_LOOP_CONTROLLER +#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER) + //#define CLOSED_LOOP_ENABLE_PIN -1 + //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1 +#endif + +/** + * Dual Steppers / Dual Endstops + * + * This section will allow you to use extra E drivers to drive a second motor for X, Y, or Z axes. + * + * For example, set X_DUAL_STEPPER_DRIVERS setting to use a second motor. If the motors need to + * spin in opposite directions set INVERT_X2_VS_X_DIR. If the second motor needs its own endstop + * set X_DUAL_ENDSTOPS. This can adjust for "racking." Use X2_USE_ENDSTOP to set the endstop plug + * that should be used for the second endstop. Extra endstops will appear in the output of 'M119'. + * + * Use X_DUAL_ENDSTOP_ADJUSTMENT to adjust for mechanical imperfection. After homing both motors + * this offset is applied to the X2 motor. To find the offset home the X axis, and measure the error + * in X2. Dual endstop offsets can be set at runtime with 'M666 X Y Z'. + */ + +//#define X_DUAL_STEPPER_DRIVERS +#if ENABLED(X_DUAL_STEPPER_DRIVERS) + #define INVERT_X2_VS_X_DIR true // Set 'true' if X motors should rotate in opposite directions + //#define X_DUAL_ENDSTOPS + #if ENABLED(X_DUAL_ENDSTOPS) + #define X2_USE_ENDSTOP _XMAX_ + #define X_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Y_DUAL_STEPPER_DRIVERS +#if ENABLED(Y_DUAL_STEPPER_DRIVERS) + #define INVERT_Y2_VS_Y_DIR true // Set 'true' if Y motors should rotate in opposite directions + //#define Y_DUAL_ENDSTOPS + #if ENABLED(Y_DUAL_ENDSTOPS) + #define Y2_USE_ENDSTOP _YMAX_ + #define Y_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Z_DUAL_STEPPER_DRIVERS +#if ENABLED(Z_DUAL_STEPPER_DRIVERS) + //#define Z_DUAL_ENDSTOPS + #if ENABLED(Z_DUAL_ENDSTOPS) + #define Z2_USE_ENDSTOP _XMAX_ + #define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Z_TRIPLE_STEPPER_DRIVERS +#if ENABLED(Z_TRIPLE_STEPPER_DRIVERS) + //#define Z_TRIPLE_ENDSTOPS + #if ENABLED(Z_TRIPLE_ENDSTOPS) + #define Z2_USE_ENDSTOP _XMAX_ + #define Z3_USE_ENDSTOP _YMAX_ + #define Z_TRIPLE_ENDSTOPS_ADJUSTMENT2 0 + #define Z_TRIPLE_ENDSTOPS_ADJUSTMENT3 0 + #endif +#endif + +/** + * Dual X Carriage + * + * This setup has two X carriages that can move independently, each with its own hotend. + * The carriages can be used to print an object with two colors or materials, or in + * "duplication mode" it can print two identical or X-mirrored objects simultaneously. + * The inactive carriage is parked automatically to prevent oozing. + * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. + * By default the X2 stepper is assigned to the first unused E plug on the board. + * + * The following Dual X Carriage modes can be selected with M605 S: + * + * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel + * results as long as it supports dual X-carriages. (M605 S0) + * + * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so + * that additional slicer support is not required. (M605 S1) + * + * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with + * the first X-carriage and extruder, to print 2 copies of the same object at the same time. + * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and + * follow with M605 S2 to initiate duplicated movement. + * + * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates + * the movement of the first except the second extruder is reversed in the X axis. + * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and + * follow with M605 S3 to initiate mirrored movement. + */ +//#define DUAL_X_CARRIAGE +#if ENABLED(DUAL_X_CARRIAGE) + #define X1_MIN_POS X_MIN_POS // Set to X_MIN_POS + #define X1_MAX_POS X_BED_SIZE // Set a maximum so the first X-carriage can't hit the parked second X-carriage + #define X2_MIN_POS 80 // Set a minimum to ensure the second X-carriage can't hit the parked first X-carriage + #define X2_MAX_POS 353 // Set this to the distance between toolheads when both heads are homed + #define X2_HOME_DIR 1 // Set to 1. The second X-carriage always homes to the maximum endstop position + #define X2_HOME_POS X2_MAX_POS // Default X2 home position. Set to X2_MAX_POS. + // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software + // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops + // without modifying the firmware (through the "M218 T1 X???" command). + // Remember: you should set the second extruder x-offset to 0 in your slicer. + + // This is the default power-up mode which can be later using M605. + #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_AUTO_PARK_MODE + + // Default x offset in duplication mode (typically set to half print bed width) + #define DEFAULT_DUPLICATION_X_OFFSET 100 + +#endif // DUAL_X_CARRIAGE + +// Activate a solenoid on the active extruder with M380. Disable all with M381. +// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid. +//#define EXT_SOLENOID + +// @section homing + +// Homing hits each endstop, retracts by these distances, then does a slower bump. +#define X_HOME_BUMP_MM 5 +#define Y_HOME_BUMP_MM 5 +#define Z_HOME_BUMP_MM 2 +#define HOMING_BUMP_DIVISOR { 2, 2, 4 } // Re-Bump Speed Divisor (Divides the Homing Feedrate) +//#define QUICK_HOME // If homing includes X and Y, do a diagonal move initially +//#define HOMING_BACKOFF_MM { 2, 2, 2 } // (mm) Move away from the endstops after homing + +// When G28 is called, this option will make Y home before X +//#define HOME_Y_BEFORE_X + +// Enable this if X or Y can't home without homing the other axis first. +//#define CODEPENDENT_XY_HOMING + +#if ENABLED(BLTOUCH) + /** + * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES + * Do not activate settings that the probe might not understand. Clones might misunderstand + * advanced commands. + * + * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then + * check the wiring of the BROWN, RED and ORANGE wires. + * + * Note: If the trigger signal of your probe is not being recognized, it has been very often + * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable" + * like they would be with a real switch. So please check the wiring first. + * + * Settings for all BLTouch and clone probes: + */ + + // Safety: The probe needs time to recognize the command. + // Minimum command delay (ms). Enable and increase if needed. + //#define BLTOUCH_DELAY 500 + + /** + * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones: + */ + + // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful + // in special cases, like noisy or filtered input configurations. + //#define BLTOUCH_FORCE_SW_MODE + + /** + * Settings for BLTouch Smart 3.0 and 3.1 + * Summary: + * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes + * - High-Speed mode + * - Disable LCD voltage options + */ + + /** + * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller! + * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup. + * If disabled, OD mode is the hard-coded default on 3.0 + * On startup, Marlin will compare its eeprom to this vale. If the selected mode + * differs, a mode set eeprom write will be completed at initialization. + * Use the option below to force an eeprom write to a V3.1 probe regardless. + */ + //#define BLTOUCH_SET_5V_MODE + + /** + * Safety: Activate if connecting a probe with an unknown voltage mode. + * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0 + * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write ) + * To preserve the life of the probe, use this once then turn it off and re-flash. + */ + //#define BLTOUCH_FORCE_MODE_SET + + /** + * Use "HIGH SPEED" mode for probing. + * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems. + * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function + * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state. + */ + //#define BLTOUCH_HS_MODE + + // Safety: Enable voltage mode settings in the LCD menu. + //#define BLTOUCH_LCD_VOLTAGE_MENU + +#endif // BLTOUCH + +/** + * Z Steppers Auto-Alignment + * Add the G34 command to align multiple Z steppers using a bed probe. + */ +//#define Z_STEPPER_AUTO_ALIGN +#if ENABLED(Z_STEPPER_AUTO_ALIGN) + // Define probe X and Y positions for Z1, Z2 [, Z3] + #define Z_STEPPER_ALIGN_X { 10, 150, 290 } + #define Z_STEPPER_ALIGN_Y { 290, 10, 290 } + // Set number of iterations to align + #define Z_STEPPER_ALIGN_ITERATIONS 3 + // Enable to restore leveling setup after operation + #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + + // Use the amplification factor to de-/increase correction step. + // In case the stepper (spindle) position is further out than the test point + // Use a value > 1. NOTE: This may cause instability + #define Z_STEPPER_ALIGN_AMP 1.0 + // Stop criterion. If the accuracy is better than this stop iterating early + #define Z_STEPPER_ALIGN_ACC 0.02 +#endif + +// @section machine + +#define AXIS_RELATIVE_MODES { false, false, false, false } + +// Add a Duplicate option for well-separated conjoined nozzles +//#define MULTI_NOZZLE_DUPLICATION + +// By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step. +#define INVERT_X_STEP_PIN false +#define INVERT_Y_STEP_PIN false +#define INVERT_Z_STEP_PIN false +#define INVERT_E_STEP_PIN false + +// Default stepper release if idle. Set to 0 to deactivate. +// Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true. +// Time can be set by M18 and M84. +#define DEFAULT_STEPPER_DEACTIVE_TIME 120 +#define DISABLE_INACTIVE_X true +#define DISABLE_INACTIVE_Y true +#define DISABLE_INACTIVE_Z true // Set to false if the nozzle will fall down on your printed part when print has finished. +#define DISABLE_INACTIVE_E true + +#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate +#define DEFAULT_MINTRAVELFEEDRATE 0.0 + +//#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated + +// @section lcd + +#if EITHER(ULTIPANEL, EXTENSIBLE_UI) + #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) + #if ENABLED(ULTIPANEL) + #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" + #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen + #endif +#endif + +// @section extras + +// minimum time in microseconds that a movement needs to take if the buffer is emptied. +#define DEFAULT_MINSEGMENTTIME 20000 + +// If defined the movements slow down when the look ahead buffer is only half full +#define SLOWDOWN + +// Frequency limit +// See nophead's blog for more info +// Not working O +//#define XY_FREQUENCY_LIMIT 15 + +// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end +// of the buffer and all stops. This should not be much greater than zero and should only be changed +// if unwanted behavior is observed on a user's machine when running at very slow speeds. +#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s) + +// +// Backlash Compensation +// Adds extra movement to axes on direction-changes to account for backlash. +// +//#define BACKLASH_COMPENSATION +#if ENABLED(BACKLASH_COMPENSATION) + // Define values for backlash distance and correction. + // If BACKLASH_GCODE is enabled these values are the defaults. + #define BACKLASH_DISTANCE_MM { 0, 0, 0 } // (mm) + #define BACKLASH_CORRECTION 0.0 // 0.0 = no correction; 1.0 = full correction + + // Set BACKLASH_SMOOTHING_MM to spread backlash correction over multiple segments + // to reduce print artifacts. (Enabling this is costly in memory and computation!) + //#define BACKLASH_SMOOTHING_MM 3 // (mm) + + // Add runtime configuration and tuning of backlash values (M425) + //#define BACKLASH_GCODE + + #if ENABLED(BACKLASH_GCODE) + // Measure the Z backlash when probing (G29) and set with "M425 Z" + #define MEASURE_BACKLASH_WHEN_PROBING + + #if ENABLED(MEASURE_BACKLASH_WHEN_PROBING) + // When measuring, the probe will move up to BACKLASH_MEASUREMENT_LIMIT + // mm away from point of contact in BACKLASH_MEASUREMENT_RESOLUTION + // increments while checking for the contact to be broken. + #define BACKLASH_MEASUREMENT_LIMIT 0.5 // (mm) + #define BACKLASH_MEASUREMENT_RESOLUTION 0.005 // (mm) + #define BACKLASH_MEASUREMENT_FEEDRATE Z_PROBE_SPEED_SLOW // (mm/m) + #endif + #endif +#endif + +/** + * Automatic backlash, position and hotend offset calibration + * + * Enable G425 to run automatic calibration using an electrically- + * conductive cube, bolt, or washer mounted on the bed. + * + * G425 uses the probe to touch the top and sides of the calibration object + * on the bed and measures and/or correct positional offsets, axis backlash + * and hotend offsets. + * + * Note: HOTEND_OFFSET and CALIBRATION_OBJECT_CENTER must be set to within + * ±5mm of true values for G425 to succeed. + */ +//#define CALIBRATION_GCODE +#if ENABLED(CALIBRATION_GCODE) + + #define CALIBRATION_MEASUREMENT_RESOLUTION 0.01 // mm + + #define CALIBRATION_FEEDRATE_SLOW 60 // mm/m + #define CALIBRATION_FEEDRATE_FAST 1200 // mm/m + #define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/m + + // The following parameters refer to the conical section of the nozzle tip. + #define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm + #define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm + + // Uncomment to enable reporting (required for "G425 V", but consumes PROGMEM). + //#define CALIBRATION_REPORTING + + // The true location and dimension the cube/bolt/washer on the bed. + #define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0} // mm + #define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0} // mm + + // Comment out any sides which are unreachable by the probe. For best + // auto-calibration results, all sides must be reachable. + #define CALIBRATION_MEASURE_RIGHT + #define CALIBRATION_MEASURE_FRONT + #define CALIBRATION_MEASURE_LEFT + #define CALIBRATION_MEASURE_BACK + + // Probing at the exact top center only works if the center is flat. If + // probing on a screwhead or hollow washer, probe near the edges. + //#define CALIBRATION_MEASURE_AT_TOP_EDGES + + // Define pin which is read during calibration + #ifndef CALIBRATION_PIN + #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop + #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin + //#define CALIBRATION_PIN_PULLDOWN + #define CALIBRATION_PIN_PULLUP + #endif +#endif + +/** + * Adaptive Step Smoothing increases the resolution of multi-axis moves, particularly at step frequencies + * below 1kHz (for AVR) or 10kHz (for ARM), where aliasing between axes in multi-axis moves causes audible + * vibration and surface artifacts. The algorithm adapts to provide the best possible step smoothing at the + * lowest stepping frequencies. + */ +//#define ADAPTIVE_STEP_SMOOTHING + +/** + * Custom Microstepping + * Override as-needed for your setup. Up to 3 MS pins are supported. + */ +//#define MICROSTEP1 LOW,LOW,LOW +//#define MICROSTEP2 HIGH,LOW,LOW +//#define MICROSTEP4 LOW,HIGH,LOW +//#define MICROSTEP8 HIGH,HIGH,LOW +//#define MICROSTEP16 LOW,LOW,HIGH +//#define MICROSTEP32 HIGH,LOW,HIGH + +// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU. +#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16] + +/** + * @section stepper motor current + * + * Some boards have a means of setting the stepper motor current via firmware. + * + * The power on motor currents are set by: + * PWM_MOTOR_CURRENT - used by MINIRAMBO & ULTIMAIN_2 + * known compatible chips: A4982 + * DIGIPOT_MOTOR_CURRENT - used by BQ_ZUM_MEGA_3D, RAMBO & SCOOVO_X9H + * known compatible chips: AD5206 + * DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2 + * known compatible chips: MCP4728 + * DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, AZTEEG_X5_MINI_WIFI, MIGHTYBOARD_REVE + * known compatible chips: MCP4451, MCP4018 + * + * Motor currents can also be set by M907 - M910 and by the LCD. + * M907 - applies to all. + * M908 - BQ_ZUM_MEGA_3D, RAMBO, PRINTRBOARD_REVF, RIGIDBOARD_V2 & SCOOVO_X9H + * M909, M910 & LCD - only PRINTRBOARD_REVF & RIGIDBOARD_V2 + */ +//#define PWM_MOTOR_CURRENT { 1300, 1300, 1250 } // Values in milliamps +//#define DIGIPOT_MOTOR_CURRENT { 135,135,135,135,135 } // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A) +//#define DAC_MOTOR_CURRENT_DEFAULT { 70, 80, 90, 80 } // Default drive percent - X, Y, Z, E axis + +// Use an I2C based DIGIPOT (e.g., Azteeg X3 Pro) +//#define DIGIPOT_I2C +#if ENABLED(DIGIPOT_I2C) && !defined(DIGIPOT_I2C_ADDRESS_A) + /** + * Common slave addresses: + * + * A (A shifted) B (B shifted) IC + * Smoothie 0x2C (0x58) 0x2D (0x5A) MCP4451 + * AZTEEG_X3_PRO 0x2C (0x58) 0x2E (0x5C) MCP4451 + * AZTEEG_X5_MINI 0x2C (0x58) 0x2E (0x5C) MCP4451 + * AZTEEG_X5_MINI_WIFI 0x58 0x5C MCP4451 + * MIGHTYBOARD_REVE 0x2F (0x5E) MCP4018 + */ + #define DIGIPOT_I2C_ADDRESS_A 0x2C // unshifted slave address for first DIGIPOT + #define DIGIPOT_I2C_ADDRESS_B 0x2D // unshifted slave address for second DIGIPOT +#endif + +//#define DIGIPOT_MCP4018 // Requires library from https://github.com/stawel/SlowSoftI2CMaster +#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8 MKS SBASE: 5 +// Actual motor currents in Amps. The number of entries must match DIGIPOT_I2C_NUM_CHANNELS. +// These correspond to the physical drivers, so be mindful if the order is changed. +#define DIGIPOT_I2C_MOTOR_CURRENTS { 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0 } // AZTEEG_X3_PRO + +//=========================================================================== +//=============================Additional Features=========================== +//=========================================================================== + +// @section lcd + +// Change values more rapidly when the encoder is rotated faster +#define ENCODER_RATE_MULTIPLIER +#if ENABLED(ENCODER_RATE_MULTIPLIER) + #define ENCODER_10X_STEPS_PER_SEC 30 // (steps/s) Encoder rate for 10x speed + #define ENCODER_100X_STEPS_PER_SEC 80 // (steps/s) Encoder rate for 100x speed +#endif + +// Play a beep when the feedrate is changed from the Status Screen +//#define BEEP_ON_FEEDRATE_CHANGE +#if ENABLED(BEEP_ON_FEEDRATE_CHANGE) + #define FEEDRATE_CHANGE_BEEP_DURATION 10 + #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 +#endif + +// Include a page of printer information in the LCD Main Menu +//#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif + +// Scroll a longer status message into view +//#define STATUS_MESSAGE_SCROLLING + +// On the Info Screen, display XY with one decimal place when possible +//#define LCD_DECIMAL_SMALL_XY + +// The timeout (in ms) to return to the status screen from sub-menus +//#define LCD_TIMEOUT_TO_STATUS 15000 + +// Add an 'M73' G-code to set the current percentage +//#define LCD_SET_PROGRESS_MANUALLY + +#if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS + //#define LCD_PROGRESS_BAR // Show a progress bar on HD44780 LCDs for SD printing + #if ENABLED(LCD_PROGRESS_BAR) + #define PROGRESS_BAR_BAR_TIME 2000 // (ms) Amount of time to show the bar + #define PROGRESS_BAR_MSG_TIME 3000 // (ms) Amount of time to show the status message + #define PROGRESS_MSG_EXPIRE 0 // (ms) Amount of time to retain the status message (0=forever) + //#define PROGRESS_MSG_ONCE // Show the message for MSG_TIME then clear it + //#define LCD_PROGRESS_BAR_TEST // Add a menu item to test the progress bar + #endif +#endif + +/** + * LED Control Menu + * Enable this feature to add LED Control to the LCD menu + */ +//#define LED_CONTROL_MENU +#if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + #define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif +#endif // LED_CONTROL_MENU + +#if ENABLED(SDSUPPORT) + + // Some RAMPS and other boards don't detect when an SD card is inserted. You can work + // around this by connecting a push button or single throw switch to the pin defined + // as SD_DETECT_PIN in your board's pins definitions. + // This setting should be disabled unless you are using a push button, pulling the pin to ground. + // Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER). + #define SD_DETECT_INVERTED + + #define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished + #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place. + + // Reverse SD sort to show "more recent" files first, according to the card's FAT. + // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended. + //#define SDCARD_RATHERRECENTFIRST + + #define SD_MENU_CONFIRM_START // Confirm the selected SD file before printing + + //#define MENU_ADDAUTOSTART // Add a menu option to run auto#.g files + + #define EVENT_GCODE_SD_STOP "M21" // G-code to run on Stop Print (e.g., "G28XY" or "G27") + + /** + * Continue after Power-Loss (Creality3D) + * + * Store the current state to the SD Card at the start of each layer + * during SD printing. If the recovery file is found at boot time, present + * an option on the LCD screen to continue the print from the last-known + * point in the file. + */ + //#define POWER_LOSS_RECOVERY + #if ENABLED(POWER_LOSS_RECOVERY) + //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume + //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. + + // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, + // especially with "vase mode" printing. Set too high and vases cannot be continued. + #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + #endif + + /** + * Sort SD file listings in alphabetical order. + * + * With this option enabled, items on SD cards will be sorted + * by name for easier navigation. + * + * By default... + * + * - Use the slowest -but safest- method for sorting. + * - Folders are sorted to the top. + * - The sort key is statically allocated. + * - No added G-code (M34) support. + * - 40 item sorting limit. (Items after the first 40 are unsorted.) + * + * SD sorting uses static allocation (as set by SDSORT_LIMIT), allowing the + * compiler to calculate the worst-case usage and throw an error if the SRAM + * limit is exceeded. + * + * - SDSORT_USES_RAM provides faster sorting via a static directory buffer. + * - SDSORT_USES_STACK does the same, but uses a local stack-based buffer. + * - SDSORT_CACHE_NAMES will retain the sorted file listing in RAM. (Expensive!) + * - SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible. (Use with caution!) + */ + //#define SDCARD_SORT_ALPHA + + // SD Card Sorting options + #if ENABLED(SDCARD_SORT_ALPHA) + #define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). Costs 27 bytes each. + #define FOLDER_SORTING -1 // -1=above 0=none 1=below + #define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 g-code. + #define SDSORT_USES_RAM true // Pre-allocate a static array for faster pre-sorting. + #define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.) + #define SDSORT_CACHE_NAMES true // Keep sorted items in RAM longer for speedy performance. Most expensive option. + #define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use! + #define SDSORT_CACHE_VFATS 2 // Maximum number of 13-byte VFAT entries to use for sorting. + // Note: Only affects SCROLL_LONG_FILENAMES with SDSORT_CACHE_NAMES but not SDSORT_DYNAMIC_RAM. + #endif + + // This allows hosts to request long names for files and folders with M33 + //#define LONG_FILENAME_HOST_SUPPORT + + // Enable this option to scroll long filenames in the SD card menu + //#define SCROLL_LONG_FILENAMES + + // Leave the heaters on after Stop Print (not recommended!) + //#define SD_ABORT_NO_COOLDOWN + + /** + * This option allows you to abort SD printing when any endstop is triggered. + * This feature must be enabled with "M540 S1" or from the LCD menu. + * To have any effect, endstops must be enabled during SD printing. + */ + //#define SD_ABORT_ON_ENDSTOP_HIT + + /** + * This option makes it easier to print the same SD Card file again. + * On print completion the LCD Menu will open with the file selected. + * You can just click to start the print, or navigate elsewhere. + */ + //#define SD_REPRINT_LAST_SELECTED_FILE + + /** + * Auto-report SdCard status with M27 S + */ + //#define AUTO_REPORT_SD_STATUS + + /** + * Support for USB thumb drives using an Arduino USB Host Shield or + * equivalent MAX3421E breakout board. The USB thumb drive will appear + * to Marlin as an SD card. + * + * The MAX3421E must be assigned the same pins as the SD card reader, with + * the following pin mapping: + * + * SCLK, MOSI, MISO --> SCLK, MOSI, MISO + * INT --> SD_DETECT_PIN + * SS --> SDSS + */ + //#define USB_FLASH_DRIVE_SUPPORT + #if ENABLED(USB_FLASH_DRIVE_SUPPORT) + #define USB_CS_PIN SDSS + #define USB_INTR_PIN SD_DETECT_PIN + #endif + + /** + * When using a bootloader that supports SD-Firmware-Flashing, + * add a menu item to activate SD-FW-Update on the next reboot. + * + * Requires ATMEGA2560 (Arduino Mega) + * + * Tested with this bootloader: + * https://github.com/FleetProbe/MicroBridge-Arduino-ATMega2560 + */ + //#define SD_FIRMWARE_UPDATE + #if ENABLED(SD_FIRMWARE_UPDATE) + #define SD_FIRMWARE_UPDATE_EEPROM_ADDR 0x1FF + #define SD_FIRMWARE_UPDATE_ACTIVE_VALUE 0xF0 + #define SD_FIRMWARE_UPDATE_INACTIVE_VALUE 0xFF + #endif + + // Add an optimized binary file transfer mode, initiated with 'M28 B1' + //#define BINARY_FILE_TRANSFER + + #ifdef TARGET_LPC1768 + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD + #endif + +#endif // SDSUPPORT + +/** + * By default an onboard SD card reader may be shared as a USB mass- + * storage device. This option hides the SD card from the host PC. + */ +//#define NO_SD_HOST_DRIVE // Disable SD Card access over USB (for security). + +/** + * Additional options for Graphical Displays + * + * Use the optimizations here to improve printing performance, + * which can be adversely affected by graphical display drawing, + * especially when doing several short moves, and when printing + * on DELTA and SCARA machines. + * + * Some of these options may result in the display lagging behind + * controller events, as there is a trade-off between reliable + * printing performance versus fast display updates. + */ +#if HAS_GRAPHICAL_LCD + // Show SD percentage next to the progress bar + //#define DOGM_SD_PERCENT + + // Enable to save many cycles by drawing a hollow frame on the Info Screen + #define XYZ_HOLLOW_FRAME + + // Enable to save many cycles by drawing a hollow frame on Menu Screens + #define MENU_HOLLOW_FRAME + + // A bigger font is available for edit items. Costs 3120 bytes of PROGMEM. + // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. + //#define USE_BIG_EDIT_FONT + + // A smaller font may be used on the Info Screen. Costs 2300 bytes of PROGMEM. + // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. + //#define USE_SMALL_INFOFONT + + // Enable this option and reduce the value to optimize screen updates. + // The normal delay is 10µs. Use the lowest value that still gives a reliable display. + //#define DOGM_SPI_DELAY_US 5 + + // Swap the CW/CCW indicators in the graphics overlay + //#define OVERLAY_GFX_REVERSE + + /** + * ST7920-based LCDs can emulate a 16 x 4 character display using + * the ST7920 character-generator for very fast screen updates. + * Enable LIGHTWEIGHT_UI to use this special display mode. + * + * Since LIGHTWEIGHT_UI has limited space, the position and status + * message occupy the same line. Set STATUS_EXPIRE_SECONDS to the + * length of time to display the status message before clearing. + * + * Set STATUS_EXPIRE_SECONDS to zero to never clear the status. + * This will prevent position updates from being displayed. + */ + #if ENABLED(U8GLIB_ST7920) + //#define LIGHTWEIGHT_UI + #if ENABLED(LIGHTWEIGHT_UI) + #define STATUS_EXPIRE_SECONDS 20 + #endif + #endif + + /** + * Status (Info) Screen customizations + * These options may affect code size and screen render time. + * Custom status screens can forcibly override these settings. + */ + //#define STATUS_COMBINE_HEATERS // Use combined heater images instead of separate ones + //#define STATUS_HOTEND_NUMBERLESS // Use plain hotend icons instead of numbered ones (with 2+ hotends) + #define STATUS_HOTEND_INVERTED // Show solid nozzle bitmaps when heating (Requires STATUS_HOTEND_ANIM) + #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating + #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating + #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap + //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap + //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames + //#define STATUS_HEAT_PERCENT // Show heating in a progress bar + //#define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash) + + // Frivolous Game Options + //#define MARLIN_BRICKOUT + //#define MARLIN_INVADERS + //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu + +#endif // HAS_GRAPHICAL_LCD + +// @section safety + +/** + * The watchdog hardware timer will do a reset and disable all outputs + * if the firmware gets too overloaded to read the temperature sensors. + * + * If you find that watchdog reboot causes your AVR board to hang forever, + * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO. + * NOTE: This method is less reliable as it can only catch hangups while + * interrupts are enabled. + */ +#define USE_WATCHDOG +#if ENABLED(USE_WATCHDOG) + //#define WATCHDOG_RESET_MANUAL +#endif + +// @section lcd + +/** + * Babystepping enables movement of the axes by tiny increments without changing + * the current position values. This feature is used primarily to adjust the Z + * axis in the first layer of a print in real-time. + * + * Warning: Does not respect endstops! + */ +//#define BABYSTEPPING +#if ENABLED(BABYSTEPPING) + //#define BABYSTEP_WITHOUT_HOMING + //#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA! + #define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way + #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion. + + //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping. + #if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING) + #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds. + // Note: Extra time may be added to mitigate controller latency. + //#define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement). + //#define MOVE_Z_WHEN_IDLE // Jump to the move Z menu on doubleclick when printer is idle. + #if ENABLED(MOVE_Z_WHEN_IDLE) + #define MOVE_Z_IDLE_MULTIPLICATOR 1 // Multiply 1mm by this factor for the move step size. + #endif + #endif + + //#define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28 + + //#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping + #if ENABLED(BABYSTEP_ZPROBE_OFFSET) + //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets + //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor + #endif +#endif + +// @section extruder + +/** + * Linear Pressure Control v1.5 + * + * Assumption: advance [steps] = k * (delta velocity [steps/s]) + * K=0 means advance disabled. + * + * NOTE: K values for LIN_ADVANCE 1.5 differ from earlier versions! + * + * Set K around 0.22 for 3mm PLA Direct Drive with ~6.5cm between the drive gear and heatbreak. + * Larger K values will be needed for flexible filament and greater distances. + * If this algorithm produces a higher speed offset than the extruder can handle (compared to E jerk) + * print acceleration will be reduced during the affected moves to keep within the limit. + * + * See http://marlinfw.org/docs/features/lin_advance.html for full instructions. + * Mention @Sebastianv650 on GitHub to alert the author of any issues. + */ +//#define LIN_ADVANCE +#if ENABLED(LIN_ADVANCE) + //#define EXTRA_LIN_ADVANCE_K // Enable for second linear advance constants + #define LIN_ADVANCE_K 0.22 // Unit: mm compression per 1mm/s extruder speed + //#define LA_DEBUG // If enabled, this will generate debug information output over USB. +#endif + +// @section leveling + +#if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL) + // Override the mesh area if the automatic (max) area is too large + //#define MESH_MIN_X MESH_INSET + //#define MESH_MIN_Y MESH_INSET + //#define MESH_MAX_X X_BED_SIZE - (MESH_INSET) + //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET) +#endif + +/** + * Repeatedly attempt G29 leveling until it succeeds. + * Stop after G29_MAX_RETRIES attempts. + */ +//#define G29_RETRY_AND_RECOVER +#if ENABLED(G29_RETRY_AND_RECOVER) + #define G29_MAX_RETRIES 3 + #define G29_HALT_ON_FAILURE + /** + * Specify the GCODE commands that will be executed when leveling succeeds, + * between attempts, and after the maximum number of retries have been tried. + */ + #define G29_SUCCESS_COMMANDS "M117 Bed leveling done." + #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0" + #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1" + +#endif + +// @section extras + +// +// G2/G3 Arc Support +// +#define ARC_SUPPORT // Disable this feature to save ~3226 bytes +#if ENABLED(ARC_SUPPORT) + #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles + //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes +#endif + +// Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes. +//#define BEZIER_CURVE_SUPPORT + +/** + * G38 Probe Target + * + * This option adds G38.2 and G38.3 (probe towards target) + * and optionally G38.4 and G38.5 (probe away from target). + * Set MULTIPLE_PROBING for G38 to probe more than once. + */ +//#define G38_PROBE_TARGET +#if ENABLED(G38_PROBE_TARGET) + //#define G38_PROBE_AWAY // Include G38.4 and G38.5 to probe away from target + #define G38_MINIMUM_MOVE 0.0275 // (mm) Minimum distance that will produce a move. +#endif + +// Moves (or segments) with fewer steps than this will be joined with the next move +#define MIN_STEPS_PER_SEGMENT 6 + +/** + * Minimum delay after setting the stepper DIR (in ns) + * 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire) + * 20 : Minimum for TMC2xxx drivers + * 200 : Minimum for A4988 drivers + * 400 : Minimum for A5984 drivers + * 500 : Minimum for LV8729 drivers (guess, no info in datasheet) + * 650 : Minimum for DRV8825 drivers + * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet) + * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet) + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MINIMUM_STEPPER_DIR_DELAY 650 + +/** + * Minimum stepper driver pulse width (in µs) + * 0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers + * 0 : Minimum 500ns for LV8729, adjusted in stepper.h + * 1 : Minimum for A4988 and A5984 stepper drivers + * 2 : Minimum for DRV8825 stepper drivers + * 3 : Minimum for TB6600 stepper drivers + * 30 : Minimum for TB6560 stepper drivers + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MINIMUM_STEPPER_PULSE 2 + +/** + * Maximum stepping rate (in Hz) the stepper driver allows + * If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE) + * 500000 : Maximum for A4988 stepper driver + * 400000 : Maximum for TMC2xxx stepper drivers + * 250000 : Maximum for DRV8825 stepper driver + * 200000 : Maximum for LV8729 stepper driver + * 150000 : Maximum for TB6600 stepper driver + * 15000 : Maximum for TB6560 stepper driver + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MAXIMUM_STEPPER_RATE 250000 + +// @section temperature + +// Control heater 0 and heater 1 in parallel. +//#define HEATERS_PARALLEL + +//=========================================================================== +//================================= Buffers ================================= +//=========================================================================== + +// @section hidden + +// The number of linear motions that can be in the plan at any give time. +// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2 (e.g. 8, 16, 32) because shifts and ors are used to do the ring-buffering. +#if ENABLED(SDSUPPORT) + #define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller +#else + #define BLOCK_BUFFER_SIZE 16 // maximize block buffer +#endif + +// @section serial + +// The ASCII buffer for serial input +#define MAX_CMD_SIZE 96 +#define BUFSIZE 4 + +// Transmission to Host Buffer Size +// To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0. +// To buffer a simple "ok" you need 4 bytes. +// For ADVANCED_OK (M105) you need 32 bytes. +// For debug-echo: 128 bytes for the optimal speed. +// Other output doesn't need to be that speedy. +// :[0, 2, 4, 8, 16, 32, 64, 128, 256] +#define TX_BUFFER_SIZE 0 + +// Host Receive Buffer Size +// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough. +// To use flow control, set this buffer size to at least 1024 bytes. +// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048] +//#define RX_BUFFER_SIZE 1024 + +#if RX_BUFFER_SIZE >= 1024 + // Enable to have the controller send XON/XOFF control characters to + // the host to signal the RX buffer is becoming full. + //#define SERIAL_XON_XOFF +#endif + +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + +#if ENABLED(SDSUPPORT) + // Enable this option to collect and display the maximum + // RX queue usage after transferring a file to SD. + //#define SERIAL_STATS_MAX_RX_QUEUED + + // Enable this option to collect and display the number + // of dropped bytes after a file transfer to SD. + //#define SERIAL_STATS_DROPPED_RX +#endif + +// Enable an emergency-command parser to intercept certain commands as they +// enter the serial receive buffer, so they cannot be blocked. +// Currently handles M108, M112, M410 +// Does not work on boards using AT90USB (USBCON) processors! +//#define EMERGENCY_PARSER + +// Bad Serial-connections can miss a received command by sending an 'ok' +// Therefore some clients abort after 30 seconds in a timeout. +// Some other clients start sending commands while receiving a 'wait'. +// This "wait" is only sent when the buffer is empty. 1 second is a good value here. +//#define NO_TIMEOUTS 1000 // Milliseconds + +// Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary. +//#define ADVANCED_OK + +// Printrun may have trouble receiving long strings all at once. +// This option inserts short delays between lines of serial output. +#define SERIAL_OVERRUN_PROTECTION + +// @section extras + +/** + * Extra Fan Speed + * Adds a secondary fan speed for each print-cooling fan. + * 'M106 P T3-255' : Set a secondary speed for + * 'M106 P T2' : Use the set secondary speed + * 'M106 P T1' : Restore the previous fan speed + */ +//#define EXTRA_FAN_SPEED + +/** + * Firmware-based and LCD-controlled retract + * + * Add G10 / G11 commands for automatic firmware-based retract / recover. + * Use M207 and M208 to define parameters for retract / recover. + * + * Use M209 to enable or disable auto-retract. + * With auto-retract enabled, all G1 E moves within the set range + * will be converted to firmware-based retract/recover moves. + * + * Be sure to turn off auto-retract during filament change. + * + * Note that M207 / M208 / M209 settings are saved to EEPROM. + * + */ +//#define FWRETRACT +#if ENABLED(FWRETRACT) + #define FWRETRACT_AUTORETRACT // costs ~500 bytes of PROGMEM + #if ENABLED(FWRETRACT_AUTORETRACT) + #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over + #define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion + #endif + #define RETRACT_LENGTH 3 // Default retract length (positive mm) + #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change + #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) + #define RETRACT_ZRAISE 0 // Default retract Z-raise (mm) + #define RETRACT_RECOVER_LENGTH 0 // Default additional recover length (mm, added to retract length when recovering) + #define RETRACT_RECOVER_LENGTH_SWAP 0 // Default additional swap recover length (mm, added to retract length when recovering from extruder change) + #define RETRACT_RECOVER_FEEDRATE 8 // Default feedrate for recovering from retraction (mm/s) + #define RETRACT_RECOVER_FEEDRATE_SWAP 8 // Default feedrate for recovering from swap retraction (mm/s) + #if ENABLED(MIXING_EXTRUDER) + //#define RETRACT_SYNC_MIXING // Retract and restore all mixing steppers simultaneously + #endif +#endif + +/** + * Universal tool change settings. + * Applies to all types of extruders except where explicitly noted. + */ +#if EXTRUDERS > 1 + // Z raise distance for tool-change, as needed for some extruders + #define TOOLCHANGE_ZRAISE 2 // (mm) + //#define TOOLCHANGE_NO_RETURN // Never return to the previous position on tool-change + + // Retract and prime filament on tool-change + //#define TOOLCHANGE_FILAMENT_SWAP + #if ENABLED(TOOLCHANGE_FILAMENT_SWAP) + #define TOOLCHANGE_FIL_SWAP_LENGTH 12 // (mm) + #define TOOLCHANGE_FIL_EXTRA_PRIME 2 // (mm) + #define TOOLCHANGE_FIL_SWAP_RETRACT_SPEED 3600 // (mm/m) + #define TOOLCHANGE_FIL_SWAP_PRIME_SPEED 3600 // (mm/m) + #endif + + /** + * Position to park head during tool change. + * Doesn't apply to SWITCHING_TOOLHEAD, DUAL_X_CARRIAGE, or PARKING_EXTRUDER + */ + //#define TOOLCHANGE_PARK + #if ENABLED(TOOLCHANGE_PARK) + #define TOOLCHANGE_PARK_XY { X_MIN_POS + 10, Y_MIN_POS + 10 } + #define TOOLCHANGE_PARK_XY_FEEDRATE 6000 // (mm/m) + #endif +#endif + +/** + * Advanced Pause + * Experimental feature for filament change support and for parking the nozzle when paused. + * Adds the GCode M600 for initiating filament change. + * If PARK_HEAD_ON_PAUSE enabled, adds the GCode M125 to pause printing and park the nozzle. + * + * Requires an LCD display. + * Requires NOZZLE_PARK_FEATURE. + * This feature is required for the default FILAMENT_RUNOUT_SCRIPT. + */ +//#define ADVANCED_PAUSE_FEATURE +#if ENABLED(ADVANCED_PAUSE_FEATURE) + #define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate. + #define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract. + // This short retract is done immediately, before parking the nozzle. + #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast. + #define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. + #define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload. + // For Bowden, the full length of the tube and nozzle. + // For direct drive, the full length of the nozzle. + // Set to 0 for manual unloading. + #define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load. + #define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material. + // 0 to disable start loading and skip to fast load only + #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast. + #define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. + #define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle. + // For Bowden, the full length of the tube and nozzle. + // For direct drive, the full length of the nozzle. + //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted. + #define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate. + #define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading. + // Set to 0 for manual extrusion. + // Filament can be extruded repeatedly from the Filament Change menu + // until extrusion is consistent, and to purge old filament. + #define ADVANCED_PAUSE_RESUME_PRIME 0 // (mm) Extra distance to prime nozzle after returning from park. + //#define ADVANCED_PAUSE_FANS_PAUSE // Turn off print-cooling fans while the machine is paused. + + // Filament Unload does a Retract, Delay, and Purge first: + #define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length. + #define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract. + #define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged. + + #define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety. + #define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed. + #define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change. + + //#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change. + //#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change + + //#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu. + //#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302) +#endif + +// @section tmc + +/** + * TMC26X Stepper Driver options + * + * The TMC26XStepper library is required for this stepper driver. + * https://github.com/trinamic/TMC26XStepper + */ +#if HAS_DRIVER(TMC26X) + + #if AXIS_DRIVER_TYPE_X(TMC26X) + #define X_MAX_CURRENT 1000 // (mA) + #define X_SENSE_RESISTOR 91 // (mOhms) + #define X_MICROSTEPS 16 // Number of microsteps + #endif + + #if AXIS_DRIVER_TYPE_X2(TMC26X) + #define X2_MAX_CURRENT 1000 + #define X2_SENSE_RESISTOR 91 + #define X2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Y(TMC26X) + #define Y_MAX_CURRENT 1000 + #define Y_SENSE_RESISTOR 91 + #define Y_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Y2(TMC26X) + #define Y2_MAX_CURRENT 1000 + #define Y2_SENSE_RESISTOR 91 + #define Y2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z(TMC26X) + #define Z_MAX_CURRENT 1000 + #define Z_SENSE_RESISTOR 91 + #define Z_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z2(TMC26X) + #define Z2_MAX_CURRENT 1000 + #define Z2_SENSE_RESISTOR 91 + #define Z2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z3(TMC26X) + #define Z3_MAX_CURRENT 1000 + #define Z3_SENSE_RESISTOR 91 + #define Z3_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E0(TMC26X) + #define E0_MAX_CURRENT 1000 + #define E0_SENSE_RESISTOR 91 + #define E0_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E1(TMC26X) + #define E1_MAX_CURRENT 1000 + #define E1_SENSE_RESISTOR 91 + #define E1_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E2(TMC26X) + #define E2_MAX_CURRENT 1000 + #define E2_SENSE_RESISTOR 91 + #define E2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E3(TMC26X) + #define E3_MAX_CURRENT 1000 + #define E3_SENSE_RESISTOR 91 + #define E3_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E4(TMC26X) + #define E4_MAX_CURRENT 1000 + #define E4_SENSE_RESISTOR 91 + #define E4_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E5(TMC26X) + #define E5_MAX_CURRENT 1000 + #define E5_SENSE_RESISTOR 91 + #define E5_MICROSTEPS 16 + #endif + +#endif // TMC26X + +// @section tmc_smart + +/** + * To use TMC2130, TMC2160, TMC2660, TMC5130, TMC5160 stepper drivers in SPI mode + * connect your SPI pins to the hardware SPI interface on your board and define + * the required CS pins in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 + * pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.). + * You may also use software SPI if you wish to use general purpose IO pins. + * + * To use TMC2208 stepper UART-configurable stepper drivers connect #_SERIAL_TX_PIN + * to the driver side PDN_UART pin with a 1K resistor. + * To use the reading capabilities, also connect #_SERIAL_RX_PIN to PDN_UART without + * a resistor. + * The drivers can also be used with hardware serial. + * + * TMCStepper library is required to use TMC stepper drivers. + * https://github.com/teemuatlut/TMCStepper + */ +#if HAS_TRINAMIC + + #define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current + #define INTERPOLATE true // Interpolate X/Y/Z_MICROSTEPS to 256 + + #if AXIS_IS_TMC(X) + #define X_CURRENT 700 // (mA) RMS current. Multiply by 1.414 for peak current. + #define X_MICROSTEPS 16 // 0..256 + #define X_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(X2) + #define X2_CURRENT 800 + #define X2_MICROSTEPS 16 + #define X2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Y) + #define Y_CURRENT 500 + #define Y_MICROSTEPS 16 + #define Y_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Y2) + #define Y2_CURRENT 800 + #define Y2_MICROSTEPS 16 + #define Y2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Z) + #define Z_CURRENT 800 + #define Z_MICROSTEPS 16 + #define Z_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Z2) + #define Z2_CURRENT 800 + #define Z2_MICROSTEPS 16 + #define Z2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Z3) + #define Z3_CURRENT 800 + #define Z3_MICROSTEPS 16 + #define Z3_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E0) + #define E0_CURRENT 650 + #define E0_MICROSTEPS 16 + #define E0_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E1) + #define E1_CURRENT 800 + #define E1_MICROSTEPS 16 + #define E1_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E2) + #define E2_CURRENT 800 + #define E2_MICROSTEPS 16 + #define E2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E3) + #define E3_CURRENT 800 + #define E3_MICROSTEPS 16 + #define E3_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E4) + #define E4_CURRENT 800 + #define E4_MICROSTEPS 16 + #define E4_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E5) + #define E5_CURRENT 800 + #define E5_MICROSTEPS 16 + #define E5_RSENSE 0.11 + #endif + + /** + * Override default SPI pins for TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160 drivers here. + * The default pins can be found in your board's pins file. + */ + //#define X_CS_PIN -1 + //#define Y_CS_PIN -1 + //#define Z_CS_PIN -1 + //#define X2_CS_PIN -1 + //#define Y2_CS_PIN -1 + //#define Z2_CS_PIN -1 + //#define Z3_CS_PIN -1 + //#define E0_CS_PIN -1 + //#define E1_CS_PIN -1 + //#define E2_CS_PIN -1 + //#define E3_CS_PIN -1 + //#define E4_CS_PIN -1 + //#define E5_CS_PIN -1 + + /** + * Software option for SPI driven drivers (TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160). + * The default SW SPI pins are defined the respective pins files, + * but you can override or define them here. + */ + //#define TMC_USE_SW_SPI + //#define TMC_SW_MOSI -1 + //#define TMC_SW_MISO -1 + //#define TMC_SW_SCK -1 + + /** + * Four TMC2209 drivers can use the same HW/SW serial port with hardware configured addresses. + * Set the address using jumpers on pins MS1 and MS2. + * Address | MS1 | MS2 + * 0 | LOW | LOW + * 1 | HIGH | LOW + * 2 | LOW | HIGH + * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. + */ + #define X_SLAVE_ADDRESS 0 + #define Y_SLAVE_ADDRESS 1 + #define Z_SLAVE_ADDRESS 2 + #define X2_SLAVE_ADDRESS 0 + #define Y2_SLAVE_ADDRESS 0 + #define Z2_SLAVE_ADDRESS 0 + #define Z3_SLAVE_ADDRESS 0 + #define E0_SLAVE_ADDRESS 3 + #define E1_SLAVE_ADDRESS 0 + #define E2_SLAVE_ADDRESS 0 + #define E3_SLAVE_ADDRESS 0 + #define E4_SLAVE_ADDRESS 0 + #define E5_SLAVE_ADDRESS 0 + + /** + * Software enable + * + * Use for drivers that do not use a dedicated enable pin, but rather handle the same + * function through a communication line such as SPI or UART. + */ + //#define SOFTWARE_DRIVER_ENABLE + + /** + * TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only + * Use Trinamic's ultra quiet stepping mode. + * When disabled, Marlin will use spreadCycle stepping mode. + */ + #define STEALTHCHOP_XY + #define STEALTHCHOP_Z + #define STEALTHCHOP_E + + /** + * Optimize spreadCycle chopper parameters by using predefined parameter sets + * or with the help of an example included in the library. + * Provided parameter sets are + * CHOPPER_DEFAULT_12V + * CHOPPER_DEFAULT_19V + * CHOPPER_DEFAULT_24V + * CHOPPER_DEFAULT_36V + * CHOPPER_PRUSAMK3_24V // Imported parameters from the official Prusa firmware for MK3 (24V) + * CHOPPER_MARLIN_119 // Old defaults from Marlin v1.1.9 + * + * Define you own with + * { , , hysteresis_start[1..8] } + */ + #define CHOPPER_TIMING CHOPPER_DEFAULT_12V + + /** + * Monitor Trinamic drivers for error conditions, + * like overtemperature and short to ground. + * In the case of overtemperature Marlin can decrease the driver current until error condition clears. + * Other detected conditions can be used to stop the current print. + * Relevant g-codes: + * M906 - Set or get motor current in milliamps using axis codes X, Y, Z, E. Report values if no axis codes given. + * M911 - Report stepper driver overtemperature pre-warn condition. + * M912 - Clear stepper driver overtemperature pre-warn condition flag. + * M122 - Report driver parameters (Requires TMC_DEBUG) + */ + #define MONITOR_DRIVER_STATUS + + #if ENABLED(MONITOR_DRIVER_STATUS) + #define CURRENT_STEP_DOWN 50 // [mA] + #define REPORT_CURRENT_CHANGE + #define STOP_ON_ERROR + #endif + + /** + * TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only + * The driver will switch to spreadCycle when stepper speed is over HYBRID_THRESHOLD. + * This mode allows for faster movements at the expense of higher noise levels. + * STEALTHCHOP_(XY|Z|E) must be enabled to use HYBRID_THRESHOLD. + * M913 X/Y/Z/E to live tune the setting + */ + //#define HYBRID_THRESHOLD + + #define X_HYBRID_THRESHOLD 100 // [mm/s] + #define X2_HYBRID_THRESHOLD 100 + #define Y_HYBRID_THRESHOLD 100 + #define Y2_HYBRID_THRESHOLD 100 + #define Z_HYBRID_THRESHOLD 3 + #define Z2_HYBRID_THRESHOLD 3 + #define Z3_HYBRID_THRESHOLD 3 + #define E0_HYBRID_THRESHOLD 30 + #define E1_HYBRID_THRESHOLD 30 + #define E2_HYBRID_THRESHOLD 30 + #define E3_HYBRID_THRESHOLD 30 + #define E4_HYBRID_THRESHOLD 30 + #define E5_HYBRID_THRESHOLD 30 + + /** + * TMC2130, TMC2160, TMC2209, TMC2660, TMC5130, and TMC5160 only + * Use StallGuard2 to sense an obstacle and trigger an endstop. + * Connect the stepper driver's DIAG1 pin to the X/Y endstop pin. + * X, Y, and Z homing will always be done in spreadCycle mode. + * + * X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity. + * Higher values make the system LESS sensitive. + * Lower value make the system MORE sensitive. + * Too low values can lead to false positives, while too high values will collide the axis without triggering. + * It is advised to set X/Y/Z_HOME_BUMP_MM to 0. + * M914 X/Y/Z to live tune the setting + */ + //#define SENSORLESS_HOMING // StallGuard capable drivers only + + /** + * Use StallGuard2 to probe the bed with the nozzle. + * + * CAUTION: This could cause damage to machines that use a lead screw or threaded rod + * to move the Z axis. Take extreme care when attempting to enable this feature. + */ + //#define SENSORLESS_PROBING // StallGuard capable drivers only + + #if EITHER(SENSORLESS_HOMING, SENSORLESS_PROBING) + // TMC2209: 0...255. TMC2130: -64...63 + #define X_STALL_SENSITIVITY 8 + #define Y_STALL_SENSITIVITY 8 + //#define Z_STALL_SENSITIVITY 8 + #endif + + /** + * Beta feature! + * Create a 50/50 square wave step pulse optimal for stepper drivers. + */ + //#define SQUARE_WAVE_STEPPING + + /** + * Enable M122 debugging command for TMC stepper drivers. + * M122 S0/1 will enable continous reporting. + */ + //#define TMC_DEBUG + + /** + * You can set your own advanced settings by filling in predefined functions. + * A list of available functions can be found on the library github page + * https://github.com/teemuatlut/TMCStepper + * + * Example: + * #define TMC_ADV() { \ + * stepperX.diag0_temp_prewarn(1); \ + * stepperY.interpolate(0); \ + * } + */ + #define TMC_ADV() { } + +#endif // HAS_TRINAMIC + +// @section L6470 + +/** + * L6470 Stepper Driver options + * + * Arduino-L6470 library (0.7.0 or higher) is required for this stepper driver. + * https://github.com/ameyer/Arduino-L6470 + * + * Requires the following to be defined in your pins_YOUR_BOARD file + * L6470_CHAIN_SCK_PIN + * L6470_CHAIN_MISO_PIN + * L6470_CHAIN_MOSI_PIN + * L6470_CHAIN_SS_PIN + * L6470_RESET_CHAIN_PIN (optional) + */ +#if HAS_DRIVER(L6470) + + //#define L6470_CHITCHAT // Display additional status info + + #if AXIS_DRIVER_TYPE_X(L6470) + #define X_MICROSTEPS 128 // Number of microsteps (VALID: 1, 2, 4, 8, 16, 32, 128) + #define X_OVERCURRENT 2000 // (mA) Current where the driver detects an over current (VALID: 375 x (1 - 16) - 6A max - rounds down) + #define X_STALLCURRENT 1500 // (mA) Current where the driver detects a stall (VALID: 31.25 * (1-128) - 4A max - rounds down) + #define X_MAX_VOLTAGE 127 // 0-255, Maximum effective voltage seen by stepper + #define X_CHAIN_POS 0 // Position in SPI chain, 0=Not in chain, 1=Nearest MOSI + #endif + + #if AXIS_DRIVER_TYPE_X2(L6470) + #define X2_MICROSTEPS 128 + #define X2_OVERCURRENT 2000 + #define X2_STALLCURRENT 1500 + #define X2_MAX_VOLTAGE 127 + #define X2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Y(L6470) + #define Y_MICROSTEPS 128 + #define Y_OVERCURRENT 2000 + #define Y_STALLCURRENT 1500 + #define Y_MAX_VOLTAGE 127 + #define Y_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Y2(L6470) + #define Y2_MICROSTEPS 128 + #define Y2_OVERCURRENT 2000 + #define Y2_STALLCURRENT 1500 + #define Y2_MAX_VOLTAGE 127 + #define Y2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Z(L6470) + #define Z_MICROSTEPS 128 + #define Z_OVERCURRENT 2000 + #define Z_STALLCURRENT 1500 + #define Z_MAX_VOLTAGE 127 + #define Z_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Z2(L6470) + #define Z2_MICROSTEPS 128 + #define Z2_OVERCURRENT 2000 + #define Z2_STALLCURRENT 1500 + #define Z2_MAX_VOLTAGE 127 + #define Z2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Z3(L6470) + #define Z3_MICROSTEPS 128 + #define Z3_OVERCURRENT 2000 + #define Z3_STALLCURRENT 1500 + #define Z3_MAX_VOLTAGE 127 + #define Z3_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E0(L6470) + #define E0_MICROSTEPS 128 + #define E0_OVERCURRENT 2000 + #define E0_STALLCURRENT 1500 + #define E0_MAX_VOLTAGE 127 + #define E0_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E1(L6470) + #define E1_MICROSTEPS 128 + #define E1_OVERCURRENT 2000 + #define E1_STALLCURRENT 1500 + #define E1_MAX_VOLTAGE 127 + #define E1_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E2(L6470) + #define E2_MICROSTEPS 128 + #define E2_OVERCURRENT 2000 + #define E2_STALLCURRENT 1500 + #define E2_MAX_VOLTAGE 127 + #define E2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E3(L6470) + #define E3_MICROSTEPS 128 + #define E3_OVERCURRENT 2000 + #define E3_STALLCURRENT 1500 + #define E3_MAX_VOLTAGE 127 + #define E3_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E4(L6470) + #define E4_MICROSTEPS 128 + #define E4_OVERCURRENT 2000 + #define E4_STALLCURRENT 1500 + #define E4_MAX_VOLTAGE 127 + #define E4_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E5(L6470) + #define E5_MICROSTEPS 128 + #define E5_OVERCURRENT 2000 + #define E5_STALLCURRENT 1500 + #define E5_MAX_VOLTAGE 127 + #define E5_CHAIN_POS 0 + #endif + + /** + * Monitor L6470 drivers for error conditions like over temperature and over current. + * In the case of over temperature Marlin can decrease the drive until the error condition clears. + * Other detected conditions can be used to stop the current print. + * Relevant g-codes: + * M906 - I1/2/3/4/5 Set or get motor drive level using axis codes X, Y, Z, E. Report values if no axis codes given. + * I not present or I0 or I1 - X, Y, Z or E0 + * I2 - X2, Y2, Z2 or E1 + * I3 - Z3 or E3 + * I4 - E4 + * I5 - E5 + * M916 - Increase drive level until get thermal warning + * M917 - Find minimum current thresholds + * M918 - Increase speed until max or error + * M122 S0/1 - Report driver parameters + */ + //#define MONITOR_L6470_DRIVER_STATUS + + #if ENABLED(MONITOR_L6470_DRIVER_STATUS) + #define KVAL_HOLD_STEP_DOWN 1 + //#define L6470_STOP_ON_ERROR + #endif + +#endif // L6470 + +/** + * TWI/I2C BUS + * + * This feature is an EXPERIMENTAL feature so it shall not be used on production + * machines. Enabling this will allow you to send and receive I2C data from slave + * devices on the bus. + * + * ; Example #1 + * ; This macro send the string "Marlin" to the slave device with address 0x63 (99) + * ; It uses multiple M260 commands with one B arg + * M260 A99 ; Target slave address + * M260 B77 ; M + * M260 B97 ; a + * M260 B114 ; r + * M260 B108 ; l + * M260 B105 ; i + * M260 B110 ; n + * M260 S1 ; Send the current buffer + * + * ; Example #2 + * ; Request 6 bytes from slave device with address 0x63 (99) + * M261 A99 B5 + * + * ; Example #3 + * ; Example serial output of a M261 request + * echo:i2c-reply: from:99 bytes:5 data:hello + */ + +// @section i2cbus + +//#define EXPERIMENTAL_I2CBUS +#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave + +// @section extras + +/** + * Photo G-code + * Add the M240 G-code to take a photo. + * The photo can be triggered by a digital pin or a physical movement. + */ +//#define PHOTO_GCODE +#if ENABLED(PHOTO_GCODE) + // A position to move to (and raise Z) before taking the photo + //#define PHOTO_POSITION { X_MAX_POS - 5, Y_MAX_POS, 0 } // { xpos, ypos, zraise } (M240 X Y Z) + //#define PHOTO_DELAY_MS 100 // (ms) Duration to pause before moving back (M240 P) + //#define PHOTO_RETRACT_MM 6.5 // (mm) E retract/recover for the photo move (M240 R S) + + // Canon RC-1 or homebrew digital camera trigger + // Data from: http://www.doc-diy.net/photo/rc-1_hacked/ + //#define PHOTOGRAPH_PIN 23 + + // Canon Hack Development Kit + // http://captain-slow.dk/2014/03/09/3d-printing-timelapses/ + //#define CHDK_PIN 4 + + // Optional second move with delay to trigger the camera shutter + //#define PHOTO_SWITCH_POSITION { X_MAX_POS, Y_MAX_POS } // { xpos, ypos } (M240 I J) + + // Duration to hold the switch or keep CHDK_PIN high + //#define PHOTO_SWITCH_MS 50 // (ms) (M240 D) +#endif + +/** + * Spindle & Laser control + * + * Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and + * to set spindle speed, spindle direction, and laser power. + * + * SuperPid is a router/spindle speed controller used in the CNC milling community. + * Marlin can be used to turn the spindle on and off. It can also be used to set + * the spindle speed from 5,000 to 30,000 RPM. + * + * You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V + * hardware PWM pin for the speed control and a pin for the rotation direction. + * + * See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details. + */ +//#define SPINDLE_FEATURE +//#define LASER_FEATURE +#if EITHER(SPINDLE_FEATURE, LASER_FEATURE) + #define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH + #define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power + #define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower + #define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power + #define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop + + #if ENABLED(SPINDLE_FEATURE) + //#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction + #define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction + #define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed + + /** + * The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power + * + * SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT + * where PWM duty cycle varies from 0 to 255 + * + * set the following for your controller (ALL MUST BE SET) + */ + #define SPEED_POWER_SLOPE 118.4 + #define SPEED_POWER_INTERCEPT 0 + #define SPEED_POWER_MIN 5000 + #define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM + #else + #define SPEED_POWER_SLOPE 0.3922 + #define SPEED_POWER_INTERCEPT 0 + #define SPEED_POWER_MIN 10 + #define SPEED_POWER_MAX 100 // 0-100% + #endif +#endif + +/** + * Coolant Control + * + * Add the M7, M8, and M9 commands to turn mist or flood coolant on and off. + * + * Note: COOLANT_MIST_PIN and/or COOLANT_FLOOD_PIN must also be defined. + */ +//#define COOLANT_CONTROL +#if ENABLED(COOLANT_CONTROL) + #define COOLANT_MIST // Enable if mist coolant is present + #define COOLANT_FLOOD // Enable if flood coolant is present + #define COOLANT_MIST_INVERT false // Set "true" if the on/off function is reversed + #define COOLANT_FLOOD_INVERT false // Set "true" if the on/off function is reversed +#endif + +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define FILWIDTH_ERROR_MARGIN 1.0 // (mm) If a measurement differs too much from nominal width ignore it + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + +/** + * CNC Coordinate Systems + * + * Enables G53 and G54-G59.3 commands to select coordinate systems + * and G92.1 to reset the workspace to native machine space. + */ +//#define CNC_COORDINATE_SYSTEMS + +/** + * Auto-report temperatures with M155 S + */ +#define AUTO_REPORT_TEMPERATURES + +/** + * Include capabilities in M115 output + */ +#define EXTENDED_CAPABILITIES_REPORT + +/** + * Disable all Volumetric extrusion options + */ +//#define NO_VOLUMETRICS + +#if DISABLED(NO_VOLUMETRICS) + /** + * Volumetric extrusion default state + * Activate to make volumetric extrusion the default method, + * with DEFAULT_NOMINAL_FILAMENT_DIA as the default diameter. + * + * M200 D0 to disable, M200 Dn to set a new diameter. + */ + //#define VOLUMETRIC_DEFAULT_ON +#endif + +/** + * Enable this option for a leaner build of Marlin that removes all + * workspace offsets, simplifying coordinate transformations, leveling, etc. + * + * - M206 and M428 are disabled. + * - G92 will revert to its behavior from Marlin 1.0. + */ +//#define NO_WORKSPACE_OFFSETS + +/** + * Set the number of proportional font spaces required to fill up a typical character space. + * This can help to better align the output of commands like `G29 O` Mesh Output. + * + * For clients that use a fixed-width font (like OctoPrint), leave this set to 1.0. + * Otherwise, adjust according to your client and font. + */ +#define PROPORTIONAL_FONT_RATIO 1.0 + +/** + * Spend 28 bytes of SRAM to optimize the GCode parser + */ +#define FASTER_GCODE_PARSER + +/** + * CNC G-code options + * Support CNC-style G-code dialects used by laser cutters, drawing machine cams, etc. + * Note that G0 feedrates should be used with care for 3D printing (if used at all). + * High feedrates may cause ringing and harm print quality. + */ +//#define PAREN_COMMENTS // Support for parentheses-delimited comments +//#define GCODE_MOTION_MODES // Remember the motion mode (G0 G1 G2 G3 G5 G38.X) and apply for X Y Z E F, etc. + +// Enable and set a (default) feedrate for all G0 moves +//#define G0_FEEDRATE 3000 // (mm/m) +#ifdef G0_FEEDRATE + //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode +#endif + +/** + * G-code Macros + * + * Add G-codes M810-M819 to define and run G-code macros. + * Macros are not saved to EEPROM. + */ +//#define GCODE_MACROS +#if ENABLED(GCODE_MACROS) + #define GCODE_MACROS_SLOTS 5 // Up to 10 may be used + #define GCODE_MACROS_SLOT_SIZE 50 // Maximum length of a single macro +#endif + +/** + * User-defined menu items that execute custom GCode + */ +//#define CUSTOM_USER_MENUS +#if ENABLED(CUSTOM_USER_MENUS) + //#define CUSTOM_USER_MENU_TITLE "Custom Commands" + #define USER_SCRIPT_DONE "M117 User Script Done" + #define USER_SCRIPT_AUDIBLE_FEEDBACK + //#define USER_SCRIPT_RETURN // Return to status screen after a script + + #define USER_DESC_1 "Home & UBL Info" + #define USER_GCODE_1 "G28\nG29 W" + + #define USER_DESC_2 "Preheat for " PREHEAT_1_LABEL + #define USER_GCODE_2 "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND) + + #define USER_DESC_3 "Preheat for " PREHEAT_2_LABEL + #define USER_GCODE_3 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND) + + #define USER_DESC_4 "Heat Bed/Home/Level" + #define USER_GCODE_4 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29" + + #define USER_DESC_5 "Home & Info" + #define USER_GCODE_5 "G28\nM503" +#endif + +/** + * Host Action Commands + * + * Define host streamer action commands in compliance with the standard. + * + * See https://reprap.org/wiki/G-code#Action_commands + * Common commands ........ poweroff, pause, paused, resume, resumed, cancel + * G29_RETRY_AND_RECOVER .. probe_rewipe, probe_failed + * + * Some features add reason codes to extend these commands. + * + * Host Prompt Support enables Marlin to use the host for user prompts so + * filament runout and other processes can be managed from the host side. + */ +//#define HOST_ACTION_COMMANDS +#if ENABLED(HOST_ACTION_COMMANDS) + //#define HOST_PROMPT_SUPPORT +#endif + +//=========================================================================== +//====================== I2C Position Encoder Settings ====================== +//=========================================================================== + +/** + * I2C position encoders for closed loop control. + * Developed by Chris Barr at Aus3D. + * + * Wiki: http://wiki.aus3d.com.au/Magnetic_Encoder + * Github: https://github.com/Aus3D/MagneticEncoder + * + * Supplier: http://aus3d.com.au/magnetic-encoder-module + * Alternative Supplier: http://reliabuild3d.com/ + * + * Reliabuild encoders have been modified to improve reliability. + */ + +//#define I2C_POSITION_ENCODERS +#if ENABLED(I2C_POSITION_ENCODERS) + + #define I2CPE_ENCODER_CNT 1 // The number of encoders installed; max of 5 + // encoders supported currently. + + #define I2CPE_ENC_1_ADDR I2CPE_PRESET_ADDR_X // I2C address of the encoder. 30-200. + #define I2CPE_ENC_1_AXIS X_AXIS // Axis the encoder module is installed on. _AXIS. + #define I2CPE_ENC_1_TYPE I2CPE_ENC_TYPE_LINEAR // Type of encoder: I2CPE_ENC_TYPE_LINEAR -or- + // I2CPE_ENC_TYPE_ROTARY. + #define I2CPE_ENC_1_TICKS_UNIT 2048 // 1024 for magnetic strips with 2mm poles; 2048 for + // 1mm poles. For linear encoders this is ticks / mm, + // for rotary encoders this is ticks / revolution. + //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper + // steps per full revolution (motor steps/rev * microstepping) + //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the + // printer will attempt to correct the error; errors + // smaller than this are ignored to minimize effects of + // measurement noise / latency (filter). + + #define I2CPE_ENC_2_ADDR I2CPE_PRESET_ADDR_Y // Same as above, but for encoder 2. + #define I2CPE_ENC_2_AXIS Y_AXIS + #define I2CPE_ENC_2_TYPE I2CPE_ENC_TYPE_LINEAR + #define I2CPE_ENC_2_TICKS_UNIT 2048 + //#define I2CPE_ENC_2_TICKS_REV (16 * 200) + //#define I2CPE_ENC_2_INVERT + #define I2CPE_ENC_2_EC_METHOD I2CPE_ECM_MICROSTEP + #define I2CPE_ENC_2_EC_THRESH 0.10 + + #define I2CPE_ENC_3_ADDR I2CPE_PRESET_ADDR_Z // Encoder 3. Add additional configuration options + #define I2CPE_ENC_3_AXIS Z_AXIS // as above, or use defaults below. + + #define I2CPE_ENC_4_ADDR I2CPE_PRESET_ADDR_E // Encoder 4. + #define I2CPE_ENC_4_AXIS E_AXIS + + #define I2CPE_ENC_5_ADDR 34 // Encoder 5. + #define I2CPE_ENC_5_AXIS E_AXIS + + // Default settings for encoders which are enabled, but without settings configured above. + #define I2CPE_DEF_TYPE I2CPE_ENC_TYPE_LINEAR + #define I2CPE_DEF_ENC_TICKS_UNIT 2048 + #define I2CPE_DEF_TICKS_REV (16 * 200) + #define I2CPE_DEF_EC_METHOD I2CPE_ECM_NONE + #define I2CPE_DEF_EC_THRESH 0.1 + + //#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given + // axis after which the printer will abort. Comment out to + // disable abort behavior. + + #define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault + // for this amount of time (in ms) before the encoder + // is trusted again. + + /** + * Position is checked every time a new command is executed from the buffer but during long moves, + * this setting determines the minimum update time between checks. A value of 100 works well with + * error rolling average when attempting to correct only for skips and not for vibration. + */ + #define I2CPE_MIN_UPD_TIME_MS 4 // (ms) Minimum time between encoder checks. + + // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise. + #define I2CPE_ERR_ROLLING_AVERAGE + +#endif // I2C_POSITION_ENCODERS + +/** + * MAX7219 Debug Matrix + * + * Add support for a low-cost 8x8 LED Matrix based on the Max7219 chip as a realtime status display. + * Requires 3 signal wires. Some useful debug options are included to demonstrate its usage. + */ +//#define MAX7219_DEBUG +#if ENABLED(MAX7219_DEBUG) + #define MAX7219_CLK_PIN 64 + #define MAX7219_DIN_PIN 57 + #define MAX7219_LOAD_PIN 44 + + //#define MAX7219_GCODE // Add the M7219 G-code to control the LED matrix + #define MAX7219_INIT_TEST 2 // Do a test pattern at initialization (Set to 2 for spiral) + #define MAX7219_NUMBER_UNITS 1 // Number of Max7219 units in chain. + #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) + // connector at: right=0 bottom=-90 top=90 left=180 + //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side + + /** + * Sample debug features + * If you add more debug displays, be careful to avoid conflicts! + */ + #define MAX7219_DEBUG_PRINTER_ALIVE // Blink corner LED of 8x8 matrix to show that the firmware is functioning + #define MAX7219_DEBUG_PLANNER_HEAD 3 // Show the planner queue head position on this and the next LED matrix row + #define MAX7219_DEBUG_PLANNER_TAIL 5 // Show the planner queue tail position on this and the next LED matrix row + + #define MAX7219_DEBUG_PLANNER_QUEUE 0 // Show the current planner queue depth on this and the next LED matrix row + // If you experience stuttering, reboots, etc. this option can reveal how + // tweaks made to the configuration are affecting the printer in real-time. +#endif + +/** + * NanoDLP Sync support + * + * Add support for Synchronized Z moves when using with NanoDLP. G0/G1 axis moves will output "Z_move_comp" + * string to enable synchronization with DLP projector exposure. This change will allow to use + * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands + */ +//#define NANODLP_Z_SYNC +#if ENABLED(NANODLP_Z_SYNC) + //#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move. + // Default behavior is limited to Z axis only. +#endif + +/** + * WiFi Support (Espressif ESP32 WiFi) + */ +//#define WIFISUPPORT +#if ENABLED(WIFISUPPORT) + #define WIFI_SSID "Wifi SSID" + #define WIFI_PWD "Wifi Password" + //#define WEBSUPPORT // Start a webserver with auto-discovery + //#define OTASUPPORT // Support over-the-air firmware updates +#endif + +/** + * Prusa Multi-Material Unit v2 + * Enable in Configuration.h + */ +#if ENABLED(PRUSA_MMU2) + + // Serial port used for communication with MMU2. + // For AVR enable the UART port used for the MMU. (e.g., internalSerial) + // For 32-bit boards check your HAL for available serial ports. (e.g., Serial2) + #define INTERNAL_SERIAL_PORT 2 + #define MMU2_SERIAL internalSerial + + // Use hardware reset for MMU if a pin is defined for it + //#define MMU2_RST_PIN 23 + + // Enable if the MMU2 has 12V stepper motors (MMU2 Firmware 1.0.2 and up) + //#define MMU2_MODE_12V + + // G-code to execute when MMU2 F.I.N.D.A. probe detects filament runout + #define MMU2_FILAMENT_RUNOUT_SCRIPT "M600" + + // Add an LCD menu for MMU2 + //#define MMU2_MENUS + #if ENABLED(MMU2_MENUS) + // Settings for filament load / unload from the LCD menu. + // This is for Prusa MK3-style extruders. Customize for your hardware. + #define MMU2_FILAMENTCHANGE_EJECT_FEED 80.0 + #define MMU2_LOAD_TO_NOZZLE_SEQUENCE \ + { 7.2, 562 }, \ + { 14.4, 871 }, \ + { 36.0, 1393 }, \ + { 14.4, 871 }, \ + { 50.0, 198 } + + #define MMU2_RAMMING_SEQUENCE \ + { 1.0, 1000 }, \ + { 1.0, 1500 }, \ + { 2.0, 2000 }, \ + { 1.5, 3000 }, \ + { 2.5, 4000 }, \ + { -15.0, 5000 }, \ + { -14.0, 1200 }, \ + { -6.0, 600 }, \ + { 10.0, 700 }, \ + { -10.0, 400 }, \ + { -50.0, 2000 } + + #endif + + //#define MMU2_DEBUG // Write debug info to serial output + +#endif // PRUSA_MMU2 + +/** + * Advanced Print Counter settings + */ +#if ENABLED(PRINTCOUNTER) + #define SERVICE_WARNING_BUZZES 3 + // Activate up to 3 service interval watchdogs + //#define SERVICE_NAME_1 "Service S" + //#define SERVICE_INTERVAL_1 100 // print hours + //#define SERVICE_NAME_2 "Service L" + //#define SERVICE_INTERVAL_2 200 // print hours + //#define SERVICE_NAME_3 "Service 3" + //#define SERVICE_INTERVAL_3 1 // print hours +#endif + +// @section develop + +/** + * M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins + */ +//#define PINS_DEBUGGING + +// Enable Marlin dev mode which adds some special commands +//#define MARLIN_DEV_MODE diff --git a/config/examples/FYSETC/Cheetah 1.2/base/Configuration.h b/config/examples/FYSETC/Cheetah 1.2/base/Configuration.h new file mode 100644 index 0000000000..f8a984aee7 --- /dev/null +++ b/config/examples/FYSETC/Cheetah 1.2/base/Configuration.h @@ -0,0 +1,2221 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Configuration.h + * + * Basic settings such as: + * + * - Type of electronics + * - Type of temperature sensor + * - Printer geometry + * - Endstop configuration + * - LCD controller + * - Extra features + * + * Advanced settings can be found in Configuration_adv.h + * + */ +#define CONFIGURATION_H_VERSION 020000 + +//=========================================================================== +//============================= Getting Started ============================= +//=========================================================================== + +/** + * Here are some standard links for getting your machine calibrated: + * + * http://reprap.org/wiki/Calibration + * http://youtu.be/wAL9d7FgInk + * http://calculator.josefprusa.cz + * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide + * http://www.thingiverse.com/thing:5573 + * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap + * http://www.thingiverse.com/thing:298812 + */ + +//=========================================================================== +//============================= DELTA Printer =============================== +//=========================================================================== +// For a Delta printer start with one of the configuration files in the +// config/examples/delta directory and customize for your machine. +// + +//=========================================================================== +//============================= SCARA Printer =============================== +//=========================================================================== +// For a SCARA printer start with the configuration files in +// config/examples/SCARA and customize for your machine. +// + +// @section info + +// User-specified version info of this build to display in [Pronterface, etc] terminal window during +// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this +// build by the user have been successfully uploaded into firmware. +#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes. +#define SHOW_BOOTSCREEN +#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1 +#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2 + +/** + * *** VENDORS PLEASE READ *** + * + * Marlin allows you to add a custom boot image for Graphical LCDs. + * With this option Marlin will first show your custom screen followed + * by the standard Marlin logo with version number and web URL. + * + * We encourage you to take advantage of this new feature and we also + * respectfully request that you retain the unmodified Marlin boot screen. + */ + +// Enable to show the bitmap in Marlin/_Bootscreen.h on startup. +//#define SHOW_CUSTOM_BOOTSCREEN + +// Enable to show the bitmap in Marlin/_Statusscreen.h on the status screen. +//#define CUSTOM_STATUS_SCREEN_IMAGE + +// @section machine + +/** + * Select the serial port on the board to use for communication with the host. + * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. + * + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] + */ +#define SERIAL_PORT 1 // libmaple 0 for USB ,1 for serial + +/** + * Select a secondary serial port on the board to use for communication with the host. + * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. + * + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] + */ +//#define SERIAL_PORT_2 -1 + +/** + * This setting determines the communication speed of the printer. + * + * 250000 works in most cases, but you might try a lower speed if + * you commonly experience drop-outs during host printing. + * You may try up to 1000000 to speed up SD file transfer. + * + * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000] + */ +#define BAUDRATE 115200 + +// Enable the Bluetooth serial interface on AT90USB devices +//#define BLUETOOTH + +// Choose the name from boards.h that matches your setup +#ifndef MOTHERBOARD + #define MOTHERBOARD BOARD_FYSETC_CHEETAH_V12 +#endif + +// Name displayed in the LCD "Ready" message and Info menu +//#define CUSTOM_MACHINE_NAME "3D Printer" + +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 +//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" + +// @section extruder + +// This defines the number of extruders +// :[1, 2, 3, 4, 5, 6] +#define EXTRUDERS 1 + +// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc. +#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 + +// For Cyclops or any "multi-extruder" that shares a single nozzle. +//#define SINGLENOZZLE + +/** + * Průša MK2 Single Nozzle Multi-Material Multiplexer, and variants. + * + * This device allows one stepper driver on a control board to drive + * two to eight stepper motors, one at a time, in a manner suitable + * for extruders. + * + * This option only allows the multiplexer to switch on tool-change. + * Additional options to configure custom E moves are pending. + */ +//#define MK2_MULTIPLEXER +#if ENABLED(MK2_MULTIPLEXER) + // Override the default DIO selector pins here, if needed. + // Some pins files may provide defaults for these pins. + //#define E_MUX0_PIN 40 // Always Required + //#define E_MUX1_PIN 42 // Needed for 3 to 8 inputs + //#define E_MUX2_PIN 44 // Needed for 5 to 8 inputs +#endif + +/** + * Prusa Multi-Material Unit v2 + * + * Requires NOZZLE_PARK_FEATURE to park print head in case MMU unit fails. + * Requires EXTRUDERS = 5 + * + * For additional configuration see Configuration_adv.h + */ +//#define PRUSA_MMU2 + +// A dual extruder that uses a single stepper motor +//#define SWITCHING_EXTRUDER +#if ENABLED(SWITCHING_EXTRUDER) + #define SWITCHING_EXTRUDER_SERVO_NR 0 + #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3] + #if EXTRUDERS > 3 + #define SWITCHING_EXTRUDER_E23_SERVO_NR 1 + #endif +#endif + +// A dual-nozzle that uses a servomotor to raise/lower one (or both) of the nozzles +//#define SWITCHING_NOZZLE +#if ENABLED(SWITCHING_NOZZLE) + #define SWITCHING_NOZZLE_SERVO_NR 0 + //#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second + #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo) +#endif + +/** + * Two separate X-carriages with extruders that connect to a moving part + * via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN. + */ +//#define PARKING_EXTRUDER + +/** + * Two separate X-carriages with extruders that connect to a moving part + * via a magnetic docking mechanism using movements and no solenoid + * + * project : https://www.thingiverse.com/thing:3080893 + * movements : https://youtu.be/0xCEiG9VS3k + * https://youtu.be/Bqbcs0CU2FE + */ +//#define MAGNETIC_PARKING_EXTRUDER + +#if EITHER(PARKING_EXTRUDER, MAGNETIC_PARKING_EXTRUDER) + + #define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders + #define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder + //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381 + + #if ENABLED(PARKING_EXTRUDER) + + #define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage + #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil + #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined. + //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381 + + #elif ENABLED(MAGNETIC_PARKING_EXTRUDER) + + #define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point + #define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple + #define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point + #define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling + + #endif + +#endif + +/** + * Switching Toolhead + * + * Support for swappable and dockable toolheads, such as + * the E3D Tool Changer. Toolheads are locked with a servo. + */ +//#define SWITCHING_TOOLHEAD + +/** + * Magnetic Switching Toolhead + * + * Support swappable and dockable toolheads with a magnetic + * docking mechanism using movement and no servo. + */ +//#define MAGNETIC_SWITCHING_TOOLHEAD + +/** + * Electromagnetic Switching Toolhead + * + * Parking for CoreXY / HBot kinematics. + * Toolheads are parked at one edge and held with an electromagnet. + * Supports more than 2 Toolheads. See https://youtu.be/JolbsAKTKf4 + */ +//#define ELECTROMAGNETIC_SWITCHING_TOOLHEAD + +#if ANY(SWITCHING_TOOLHEAD, MAGNETIC_SWITCHING_TOOLHEAD, ELECTROMAGNETIC_SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_Y_POS 235 // (mm) Y position of the toolhead dock + #define SWITCHING_TOOLHEAD_Y_SECURITY 10 // (mm) Security distance Y axis + #define SWITCHING_TOOLHEAD_Y_CLEAR 60 // (mm) Minimum distance from dock for unobstructed X axis + #define SWITCHING_TOOLHEAD_X_POS { 215, 0 } // (mm) X positions for parking the extruders + #if ENABLED(SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_SERVO_NR 2 // Index of the servo connector + #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock + #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif + #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching + #endif +#endif + +/** + * "Mixing Extruder" + * - Adds G-codes M163 and M164 to set and "commit" the current mix factors. + * - Extends the stepping routines to move multiple steppers in proportion to the mix. + * - Optional support for Repetier Firmware's 'M164 S' supporting virtual tools. + * - This implementation supports up to two mixing extruders. + * - Enable DIRECT_MIXING_IN_G1 for M165 and mixing in G1 (from Pia Taubert's reference implementation). + */ +//#define MIXING_EXTRUDER +#if ENABLED(MIXING_EXTRUDER) + #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder + #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164 + //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands + //#define GRADIENT_MIX // Support for gradient mixing with M166 and LCD + #if ENABLED(GRADIENT_MIX) + //#define GRADIENT_VTOOL // Add M166 T to use a V-tool index as a Gradient alias + #endif +#endif + +// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). +// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). +// For the other hotends it is their distance from the extruder 0 hotend. +//#define HOTEND_OFFSET_X { 0.0, 20.00 } // (mm) relative X-offset for each nozzle +//#define HOTEND_OFFSET_Y { 0.0, 5.00 } // (mm) relative Y-offset for each nozzle +//#define HOTEND_OFFSET_Z { 0.0, 0.00 } // (mm) relative Z-offset for each nozzle + +// @section machine + +/** + * Power Supply Control + * + * Enable and connect the power supply to the PS_ON_PIN. + * Specify whether the power supply is active HIGH or active LOW. + */ +//#define PSU_CONTROL +//#define PSU_NAME "Power Supply" + +#if ENABLED(PSU_CONTROL) + #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2) + + //#define PS_DEFAULT_OFF // Keep power off until enabled directly with M80 + + //#define AUTO_POWER_CONTROL // Enable automatic control of the PS_ON pin + #if ENABLED(AUTO_POWER_CONTROL) + #define AUTO_POWER_FANS // Turn on PSU if fans need power + #define AUTO_POWER_E_FANS + #define AUTO_POWER_CONTROLLERFAN + #define AUTO_POWER_CHAMBER_FAN + //#define AUTO_POWER_E_TEMP 50 // (°C) Turn on PSU over this temperature + //#define AUTO_POWER_CHAMBER_TEMP 30 // (°C) Turn on PSU over this temperature + #define POWER_TIMEOUT 30 + #endif +#endif + +// @section temperature + +//=========================================================================== +//============================= Thermal Settings ============================ +//=========================================================================== + +/** + * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table + * + * Temperature sensors available: + * + * -4 : thermocouple with AD8495 + * -3 : thermocouple with MAX31855 (only for sensor 0) + * -2 : thermocouple with MAX6675 (only for sensor 0) + * -1 : thermocouple with AD595 + * 0 : not used + * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 3 : Mendel-parts thermistor (4.7k pullup) + * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! + * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) + * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) + * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) + * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) + * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) + * 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) + * 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) + * 10 : 100k RS thermistor 198-961 (4.7k pullup) + * 11 : 100k beta 3950 1% thermistor (4.7k pullup) + * 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) + * 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" + * 15 : 100k thermistor calibration for JGAurora A5 hotend + * 18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327 + * 20 : the PT100 circuit found in the Ultimainboard V2.x + * 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 + * 61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup + * 66 : 4.7M High Temperature thermistor from Dyze Design + * 67 : 450C thermistor from SliceEngineering + * 70 : the 100K thermistor found in the bq Hephestos 2 + * 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor + * + * 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k. + * (but gives greater accuracy and more stable PID) + * 51 : 100k thermistor - EPCOS (1k pullup) + * 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup) + * 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) + * + * 1047 : Pt1000 with 4k7 pullup + * 1010 : Pt1000 with 1k pullup (non standard) + * 147 : Pt100 with 4k7 pullup + * 110 : Pt100 with 1k pullup (non standard) + * + * 1000 : Custom - Specify parameters in Configuration_adv.h + * + * Use these for Testing or Development purposes. NEVER for production machine. + * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. + * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. + * + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + */ +#define TEMP_SENSOR_0 1 +#define TEMP_SENSOR_1 0 +#define TEMP_SENSOR_2 0 +#define TEMP_SENSOR_3 0 +#define TEMP_SENSOR_4 0 +#define TEMP_SENSOR_5 0 +#define TEMP_SENSOR_BED 1 +#define TEMP_SENSOR_CHAMBER 0 + +// Dummy thermistor constant temperature readings, for use with 998 and 999 +#define DUMMY_THERMISTOR_998_VALUE 25 +#define DUMMY_THERMISTOR_999_VALUE 100 + +// Use temp sensor 1 as a redundant sensor with sensor 0. If the readings +// from the two sensors differ too much the print will be aborted. +//#define TEMP_SENSOR_1_AS_REDUNDANT +#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 + +#define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109 +#define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer +#define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target + +#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190 +#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer +#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target + +// Below this temperature the heater will be switched off +// because it probably indicates a broken thermistor wire. +#define HEATER_0_MINTEMP 5 +#define HEATER_1_MINTEMP 5 +#define HEATER_2_MINTEMP 5 +#define HEATER_3_MINTEMP 5 +#define HEATER_4_MINTEMP 5 +#define HEATER_5_MINTEMP 5 +#define BED_MINTEMP 5 + +// Above this temperature the heater will be switched off. +// This can protect components from overheating, but NOT from shorts and failures. +// (Use MINTEMP for thermistor short/failure protection.) +#define HEATER_0_MAXTEMP 275 +#define HEATER_1_MAXTEMP 275 +#define HEATER_2_MAXTEMP 275 +#define HEATER_3_MAXTEMP 275 +#define HEATER_4_MAXTEMP 275 +#define HEATER_5_MAXTEMP 275 +#define BED_MAXTEMP 150 + +//=========================================================================== +//============================= PID Settings ================================ +//=========================================================================== +// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning + +// Comment the following line to disable PID and enable bang-bang. +#define PIDTEMP +#define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current +#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current +#define PID_K1 0.95 // Smoothing factor within any PID loop +#if ENABLED(PIDTEMP) + //#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM) + //#define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM) + //#define PID_DEBUG // Sends debug data to the serial port. + //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX + //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay + //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] + #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature + // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. + + // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it + + //PID for Makerlab J-head + #define DEFAULT_Kp 21.73 + #define DEFAULT_Ki 1.54 + #define DEFAULT_Kd 76.55 + + // Ultimaker + //#define DEFAULT_Kp 22.2 + //#define DEFAULT_Ki 1.08 + //#define DEFAULT_Kd 114 + + // MakerGear + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 + + // Mendel Parts V9 on 12V + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 + +#endif // PIDTEMP + +//=========================================================================== +//====================== PID > Bed Temperature Control ====================== +//=========================================================================== + +/** + * PID Bed Heating + * + * If this option is enabled set PID constants below. + * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis. + * + * The PID frequency will be the same as the extruder PWM. + * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz, + * which is fine for driving a square wave into a resistive load and does not significantly + * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W + * heater. If your configuration is significantly different than this and you don't understand + * the issues involved, don't use bed PID until someone else verifies that your hardware works. + */ +//#define PIDTEMPBED + +//#define BED_LIMIT_SWITCHING + +/** + * Max Bed Power + * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis). + * When set to any value below 255, enables a form of PWM to the bed that acts like a divider + * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED) + */ +#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current + +#if ENABLED(PIDTEMPBED) + //#define MIN_BED_POWER 0 + //#define PID_BED_DEBUG // Sends debug data to the serial port. + + //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) + //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 + + //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) + //from pidautotune + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 + + // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. +#endif // PIDTEMPBED + +// @section extruder + +/** + * Prevent extrusion if the temperature is below EXTRUDE_MINTEMP. + * Add M302 to set the minimum extrusion temperature and/or turn + * cold extrusion prevention on and off. + * + * *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! *** + */ +#define PREVENT_COLD_EXTRUSION +#define EXTRUDE_MINTEMP 170 + +/** + * Prevent a single extrusion longer than EXTRUDE_MAXLENGTH. + * Note: For Bowden Extruders make this large enough to allow load/unload. + */ +#define PREVENT_LENGTHY_EXTRUDE +#define EXTRUDE_MAXLENGTH 200 + +//=========================================================================== +//======================== Thermal Runaway Protection ======================= +//=========================================================================== + +/** + * Thermal Protection provides additional protection to your printer from damage + * and fire. Marlin always includes safe min and max temperature ranges which + * protect against a broken or disconnected thermistor wire. + * + * The issue: If a thermistor falls out, it will report the much lower + * temperature of the air in the room, and the the firmware will keep + * the heater on. + * + * If you get "Thermal Runaway" or "Heating failed" errors the + * details can be tuned in Configuration_adv.h + */ + +#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders +#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed +#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber + +//=========================================================================== +//============================= Mechanical Settings ========================= +//=========================================================================== + +// @section machine + +// Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics +// either in the usual order or reversed +//#define COREXY +//#define COREXZ +//#define COREYZ +//#define COREYX +//#define COREZX +//#define COREZY + +//=========================================================================== +//============================== Endstop Settings =========================== +//=========================================================================== + +// @section homing + +// Specify here all the endstop connectors that are connected to any endstop or probe. +// Almost all printers will be using one per axis. Probes will use one or more of the +// extra connectors. Leave undefined any used for non-endstop and non-probe purposes. +#define USE_XMIN_PLUG +#define USE_YMIN_PLUG +#define USE_ZMIN_PLUG +//#define USE_XMAX_PLUG +//#define USE_YMAX_PLUG +//#define USE_ZMAX_PLUG + +// Enable pullup for all endstops to prevent a floating state +#define ENDSTOPPULLUPS +#if DISABLED(ENDSTOPPULLUPS) + // Disable ENDSTOPPULLUPS to set pullups individually + //#define ENDSTOPPULLUP_XMAX + //#define ENDSTOPPULLUP_YMAX + //#define ENDSTOPPULLUP_ZMAX + //#define ENDSTOPPULLUP_XMIN + //#define ENDSTOPPULLUP_YMIN + //#define ENDSTOPPULLUP_ZMIN + //#define ENDSTOPPULLUP_ZMIN_PROBE +#endif + +// Enable pulldown for all endstops to prevent a floating state +//#define ENDSTOPPULLDOWNS +#if DISABLED(ENDSTOPPULLDOWNS) + // Disable ENDSTOPPULLDOWNS to set pulldowns individually + //#define ENDSTOPPULLDOWN_XMAX + //#define ENDSTOPPULLDOWN_YMAX + //#define ENDSTOPPULLDOWN_ZMAX + //#define ENDSTOPPULLDOWN_XMIN + //#define ENDSTOPPULLDOWN_YMIN + //#define ENDSTOPPULLDOWN_ZMIN + //#define ENDSTOPPULLDOWN_ZMIN_PROBE +#endif + +// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup). +#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe. + +/** + * Stepper Drivers + * + * These settings allow Marlin to tune stepper driver timing and enable advanced options for + * stepper drivers that support them. You may also override timing options in Configuration_adv.h. + * + * A4988 is assumed for unspecified drivers. + * + * Options: A4988, A5984, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100, + * TMC2130, TMC2130_STANDALONE, TMC2160, TMC2160_STANDALONE, + * TMC2208, TMC2208_STANDALONE, TMC2209, TMC2209_STANDALONE, + * TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE, + * TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE + * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE'] + */ +#define X_DRIVER_TYPE TMC2208 +#define Y_DRIVER_TYPE TMC2208 +#define Z_DRIVER_TYPE TMC2208 +//#define X2_DRIVER_TYPE A4988 +//#define Y2_DRIVER_TYPE A4988 +//#define Z2_DRIVER_TYPE A4988 +//#define Z3_DRIVER_TYPE A4988 +#define E0_DRIVER_TYPE TMC2208 +//#define E1_DRIVER_TYPE A4988 +//#define E2_DRIVER_TYPE A4988 +//#define E3_DRIVER_TYPE A4988 +//#define E4_DRIVER_TYPE A4988 +//#define E5_DRIVER_TYPE A4988 + +// Enable this feature if all enabled endstop pins are interrupt-capable. +// This will remove the need to poll the interrupt pins, saving many CPU cycles. +//#define ENDSTOP_INTERRUPTS_FEATURE + +/** + * Endstop Noise Threshold + * + * Enable if your probe or endstops falsely trigger due to noise. + * + * - Higher values may affect repeatability or accuracy of some bed probes. + * - To fix noise install a 100nF ceramic capacitor inline with the switch. + * - This feature is not required for common micro-switches mounted on PCBs + * based on the Makerbot design, which already have the 100nF capacitor. + * + * :[2,3,4,5,6,7] + */ +//#define ENDSTOP_NOISE_THRESHOLD 2 + +//============================================================================= +//============================== Movement Settings ============================ +//============================================================================= +// @section motion + +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * With this option each E stepper can have its own factors for the + * following movement settings. If fewer factors are given than the + * total number of extruders, the last value applies to the rest. + */ +//#define DISTINCT_E_FACTORS + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] + */ +#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 93 } + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] + */ +#define DEFAULT_MAX_FEEDRATE { 500, 500, 5, 25 } + +/** + * Default Max Acceleration (change/s) change = mm/s + * (Maximum start speed for accelerated moves) + * Override with M201 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] + */ +#define DEFAULT_MAX_ACCELERATION { 500, 500, 100, 5000 } + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 500 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 500 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 500 // X, Y, Z acceleration for travel (non printing) moves + +/** + * Junction Deviation + * + * Use Junction Deviation instead of traditional Jerk Limiting + * + * See: + * https://reprap.org/forum/read.php?1,739819 + * http://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html + */ +//#define JUNCTION_DEVIATION +#if ENABLED(JUNCTION_DEVIATION) + #define JUNCTION_DEVIATION_MM 0.02 // (mm) Distance from real junction edge +#endif + +/** + * Default Jerk (mm/s) + * Override with M205 X Y Z E + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#if DISABLED(JUNCTION_DEVIATION) + #define DEFAULT_XJERK 10.0 + #define DEFAULT_YJERK 10.0 + #define DEFAULT_ZJERK 0.3 +#endif + +#define DEFAULT_EJERK 5.0 // May be used by Linear Advance + +/** + * S-Curve Acceleration + * + * This option eliminates vibration during printing by fitting a Bézier + * curve to move acceleration, producing much smoother direction changes. + * + * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained + */ +//#define S_CURVE_ACCELERATION + +//=========================================================================== +//============================= Z Probe Options ============================= +//=========================================================================== +// @section probes + +// +// See http://marlinfw.org/docs/configuration/probes.html +// + +/** + * Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + * + * Enable this option for a probe connected to the Z Min endstop pin. + */ +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +/** + * Z_MIN_PROBE_PIN + * + * Define this pin if the probe is not connected to Z_MIN_PIN. + * If not defined the default pin for the selected MOTHERBOARD + * will be used. Most of the time the default is what you want. + * + * - The simplest option is to use a free endstop connector. + * - Use 5V for powered (usually inductive) sensors. + * + * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin: + * - For simple switches connect... + * - normally-closed switches to GND and D32. + * - normally-open switches to 5V and D32. + * + */ +//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default + +/** + * Probe Type + * + * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. + * Activate one of these to use Auto Bed Leveling below. + */ + +/** + * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe. + * Use G29 repeatedly, adjusting the Z height at each point with movement commands + * or (with LCD_BED_LEVELING) the LCD controller. + */ +//#define PROBE_MANUALLY +//#define MANUAL_PROBE_START_Z 0.2 + +/** + * A Fix-Mounted Probe either doesn't deploy or needs manual deployment. + * (e.g., an inductive probe or a nozzle-based probe-switch.) + */ +//#define FIX_MOUNTED_PROBE + +/** + * Z Servo Probe, such as an endstop switch on a rotating arm. + */ +//#define Z_PROBE_SERVO_NR 0 // Defaults to SERVO 0 connector. +//#define Z_SERVO_ANGLES { 70, 0 } // Z Servo Deploy and Stow angles + +/** + * The BLTouch probe uses a Hall effect sensor and emulates a servo. + */ +//#define BLTOUCH + +/** + * Touch-MI Probe by hotends.fr + * + * This probe is deployed and activated by moving the X-axis to a magnet at the edge of the bed. + * By default, the magnet is assumed to be on the left and activated by a home. If the magnet is + * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position. + * + * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING, + * and a minimum Z_HOMING_HEIGHT of 10. + */ +//#define TOUCH_MI_PROBE +#if ENABLED(TOUCH_MI_PROBE) + #define TOUCH_MI_RETRACT_Z 0.5 // Height at which the probe retracts + //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2) // For a magnet on the right side of the bed + //#define TOUCH_MI_MANUAL_DEPLOY // For manual deploy (LCD menu) +#endif + +// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) +//#define SOLENOID_PROBE + +// A sled-mounted probe like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +// A probe deployed by moving the x-axis, such as the Wilson II's rack-and-pinion probe designed by Marty Rice. +//#define RACK_AND_PINION_PROBE +#if ENABLED(RACK_AND_PINION_PROBE) + #define Z_PROBE_DEPLOY_X X_MIN_POS + #define Z_PROBE_RETRACT_X X_MAX_POS +#endif + +// +// For Z_PROBE_ALLEN_KEY see the Delta example configurations. +// + +/** + * Z Probe to nozzle (X,Y) offset, relative to (0, 0). + * X and Y offsets must be integers. + * + * In the following example the X and Y offsets are both positive: + * #define X_PROBE_OFFSET_FROM_EXTRUDER 10 + * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 + * + * +-- BACK ---+ + * | | + * L | (+) P | R <-- probe (20,20) + * E | | I + * F | (-) N (+) | G <-- nozzle (10,10) + * T | | H + * | (-) | T + * | | + * O-- FRONT --+ + * (0,0) + */ +#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle] + +// Certain types of probes need to stay away from edges +#define MIN_PROBE_EDGE 10 + +// X and Y axis travel speed (mm/m) between probes +#define XY_PROBE_SPEED 8000 + +// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2) +#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z + +// Feedrate (mm/m) for the "accurate" probe of each point +#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) + +/** + * Multiple Probing + * + * You may get improved results by probing 2 or more times. + * With EXTRA_PROBING the more atypical reading(s) will be disregarded. + * + * A total of 2 does fast/slow probes with a weighted average. + * A total of 3 or more adds more slow probes, taking the average. + */ +//#define MULTIPLE_PROBING 2 +//#define EXTRA_PROBING 1 + +/** + * Z probes require clearance when deploying, stowing, and moving between + * probe points to avoid hitting the bed and other hardware. + * Servo-mounted probes require extra space for the arm to rotate. + * Inductive probes need space to keep from triggering early. + * + * Use these settings to specify the distance (mm) to raise the probe (or + * lower the bed). The values set here apply over and above any (negative) + * probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD. + * Only integer values >= 1 are valid here. + * + * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle. + * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle. + */ +#define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow +#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points +#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes +//#define Z_AFTER_PROBING 5 // Z position after probing is done + +#define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping + +// For M851 give a range for adjusting the Z probe offset +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + +// Enable the M48 repeatability test to test probe accuracy +//#define Z_MIN_PROBE_REPEATABILITY_TEST + +// Before deploy/stow pause for user confirmation +//#define PAUSE_BEFORE_DEPLOY_STOW +#if ENABLED(PAUSE_BEFORE_DEPLOY_STOW) + //#define PAUSE_PROBE_DEPLOY_WHEN_TRIGGERED // For Manual Deploy Allenkey Probe +#endif + +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + +// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 +// :{ 0:'Low', 1:'High' } +#define X_ENABLE_ON 0 +#define Y_ENABLE_ON 0 +#define Z_ENABLE_ON 0 +#define E_ENABLE_ON 0 // For all extruders + +// Disables axis stepper immediately when it's not being used. +// WARNING: When motors turn off there is a chance of losing position accuracy! +#define DISABLE_X false +#define DISABLE_Y false +#define DISABLE_Z false + +// Warn on display about possibly reduced accuracy +//#define DISABLE_REDUCED_ACCURACY_WARNING + +// @section extruder + +#define DISABLE_E false // For all extruders +#define DISABLE_INACTIVE_EXTRUDER // Keep only the active extruder enabled + +// @section machine + +// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way. +#define INVERT_X_DIR true +#define INVERT_Y_DIR true +#define INVERT_Z_DIR false + +// @section extruder + +// For direct drive extruder v9 set to true, for geared extruder set to false. +#define INVERT_E0_DIR true +#define INVERT_E1_DIR false +#define INVERT_E2_DIR false +#define INVERT_E3_DIR false +#define INVERT_E4_DIR false +#define INVERT_E5_DIR false + +// @section homing + +//#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed + +//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off. + +//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ... + // Be sure you have this distance over your Z_MAX_POS in case. + +// Direction of endstops when homing; 1=MAX, -1=MIN +// :[-1,1] +#define X_HOME_DIR -1 +#define Y_HOME_DIR -1 +#define Z_HOME_DIR -1 + +// @section machine + +// The size of the print bed +#define X_BED_SIZE 235 +#define Y_BED_SIZE 235 + +// Travel limits (mm) after homing, corresponding to endstop positions. +#define X_MIN_POS 0 +#define Y_MIN_POS 0 +#define Z_MIN_POS 0 +#define X_MAX_POS X_BED_SIZE +#define Y_MAX_POS Y_BED_SIZE +#define Z_MAX_POS 260 + +/** + * Software Endstops + * + * - Prevent moves outside the set machine bounds. + * - Individual axes can be disabled, if desired. + * - X and Y only apply to Cartesian robots. + * - Use 'M211' to set software endstops on/off or report current state + */ + +// Min software endstops constrain movement within minimum coordinate bounds +#define MIN_SOFTWARE_ENDSTOPS +#if ENABLED(MIN_SOFTWARE_ENDSTOPS) + #define MIN_SOFTWARE_ENDSTOP_X + #define MIN_SOFTWARE_ENDSTOP_Y + #define MIN_SOFTWARE_ENDSTOP_Z +#endif + +// Max software endstops constrain movement within maximum coordinate bounds +#define MAX_SOFTWARE_ENDSTOPS +#if ENABLED(MAX_SOFTWARE_ENDSTOPS) + #define MAX_SOFTWARE_ENDSTOP_X + #define MAX_SOFTWARE_ENDSTOP_Y + #define MAX_SOFTWARE_ENDSTOP_Z +#endif + +#if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS) + //#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD +#endif + +/** + * Filament Runout Sensors + * Mechanical or opto endstops are used to check for the presence of filament. + * + * RAMPS-based boards use SERVO3_PIN for the first runout sensor. + * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc. + * By default the firmware assumes HIGH=FILAMENT PRESENT. + */ +//#define FILAMENT_RUNOUT_SENSOR +#if ENABLED(FILAMENT_RUNOUT_SENSOR) + #define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each. + #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor. + #define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins. + //#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins. + + // Set one or more commands to execute on filament runout. + // (After 'M412 H' Marlin will ask the host to handle the process.) + #define FILAMENT_RUNOUT_SCRIPT "M600" + + // After a runout is detected, continue printing this length of filament + // before executing the runout script. Useful for a sensor at the end of + // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead. + //#define FILAMENT_RUNOUT_DISTANCE_MM 25 + + #ifdef FILAMENT_RUNOUT_DISTANCE_MM + // Enable this option to use an encoder disc that toggles the runout pin + // as the filament moves. (Be sure to set FILAMENT_RUNOUT_DISTANCE_MM + // large enough to avoid false positives.) + //#define FILAMENT_MOTION_SENSOR + #endif +#endif + +//=========================================================================== +//=============================== Bed Leveling ============================== +//=========================================================================== +// @section calibrate + +/** + * Choose one of the options below to enable G29 Bed Leveling. The parameters + * and behavior of G29 will change depending on your selection. + * + * If using a Probe for Z Homing, enable Z_SAFE_HOMING also! + * + * - AUTO_BED_LEVELING_3POINT + * Probe 3 arbitrary points on the bed (that aren't collinear) + * You specify the XY coordinates of all 3 points. + * The result is a single tilted plane. Best for a flat bed. + * + * - AUTO_BED_LEVELING_LINEAR + * Probe several points in a grid. + * You specify the rectangle and the density of sample points. + * The result is a single tilted plane. Best for a flat bed. + * + * - AUTO_BED_LEVELING_BILINEAR + * Probe several points in a grid. + * You specify the rectangle and the density of sample points. + * The result is a mesh, best for large or uneven beds. + * + * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling) + * A comprehensive bed leveling system combining the features and benefits + * of other systems. UBL also includes integrated Mesh Generation, Mesh + * Validation and Mesh Editing systems. + * + * - MESH_BED_LEVELING + * Probe a grid manually + * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.) + * For machines without a probe, Mesh Bed Leveling provides a method to perform + * leveling in steps so you can manually adjust the Z height at each grid-point. + * With an LCD controller the process is guided step-by-step. + */ +//#define AUTO_BED_LEVELING_3POINT +//#define AUTO_BED_LEVELING_LINEAR +//#define AUTO_BED_LEVELING_BILINEAR +//#define AUTO_BED_LEVELING_UBL +//#define MESH_BED_LEVELING + +/** + * Normally G28 leaves leveling disabled on completion. Enable + * this option to have G28 restore the prior leveling state. + */ +//#define RESTORE_LEVELING_AFTER_G28 + +/** + * Enable detailed logging of G28, G29, M48, etc. + * Turn on with the command 'M111 S32'. + * NOTE: Requires a lot of PROGMEM! + */ +//#define DEBUG_LEVELING_FEATURE + +#if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_BILINEAR, AUTO_BED_LEVELING_UBL) + // Gradually reduce leveling correction until a set height is reached, + // at which point movement will be level to the machine's XY plane. + // The height can be set with M420 Z + #define ENABLE_LEVELING_FADE_HEIGHT + + // For Cartesian machines, instead of dividing moves on mesh boundaries, + // split up moves into short segments like a Delta. This follows the + // contours of the bed more closely than edge-to-edge straight moves. + #define SEGMENT_LEVELED_MOVES + #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one) + + /** + * Enable the G26 Mesh Validation Pattern tool. + */ + //#define G26_MESH_VALIDATION + #if ENABLED(G26_MESH_VALIDATION) + #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle. + #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool. + #define MESH_TEST_HOTEND_TEMP 205 // (°C) Default nozzle temperature for the G26 Mesh Validation Tool. + #define MESH_TEST_BED_TEMP 60 // (°C) Default bed temperature for the G26 Mesh Validation Tool. + #define G26_XY_FEEDRATE 20 // (mm/s) Feedrate for XY Moves for the G26 Mesh Validation Tool. + #endif + +#endif + +#if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR) + + // Set the number of grid points per dimension. + #define GRID_MAX_POINTS_X 3 + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + // Set the boundaries for probing (where the probe can reach). + //#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE + //#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE)) + //#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE + //#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE)) + + // Probe along the Y axis, advancing X after each column + //#define PROBE_Y_FIRST + + #if ENABLED(AUTO_BED_LEVELING_BILINEAR) + + // Beyond the probed grid, continue the implied tilt? + // Default is to maintain the height of the nearest edge. + //#define EXTRAPOLATE_BEYOND_GRID + + // + // Experimental Subdivision of the grid by Catmull-Rom method. + // Synthesizes intermediate points to produce a more detailed mesh. + // + //#define ABL_BILINEAR_SUBDIVISION + #if ENABLED(ABL_BILINEAR_SUBDIVISION) + // Number of subdivisions between probe points + #define BILINEAR_SUBDIVISIONS 3 + #endif + + #endif + +#elif ENABLED(AUTO_BED_LEVELING_UBL) + + //=========================================================================== + //========================= Unified Bed Leveling ============================ + //=========================================================================== + + //#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh + + #define MESH_INSET 1 // Set Mesh bounds as an inset region of the bed + #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited. + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + #define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle + #define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500 + + //#define UBL_Z_RAISE_WHEN_OFF_MESH 2.5 // When the nozzle is off the mesh, this value is used + // as the Z-Height correction value. + +#elif ENABLED(MESH_BED_LEVELING) + + //=========================================================================== + //=================================== Mesh ================================== + //=========================================================================== + + #define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed + #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited. + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS + +#endif // BED_LEVELING + +/** + * Points to probe for all 3-point Leveling procedures. + * Override if the automatically selected points are inadequate. + */ +#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL) + //#define PROBE_PT_1_X 15 + //#define PROBE_PT_1_Y 180 + //#define PROBE_PT_2_X 15 + //#define PROBE_PT_2_Y 20 + //#define PROBE_PT_3_X 170 + //#define PROBE_PT_3_Y 20 +#endif + +/** + * Add a bed leveling sub-menu for ABL or MBL. + * Include a guided procedure if manual probing is enabled. + */ +//#define LCD_BED_LEVELING + +#if ENABLED(LCD_BED_LEVELING) + #define MESH_EDIT_Z_STEP 0.025 // (mm) Step size while manually probing Z axis. + #define LCD_PROBE_Z_RANGE 4 // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment + //#define MESH_EDIT_MENU // Add a menu to edit mesh points +#endif + +// Add a menu item to move between bed corners for manual bed adjustment +//#define LEVEL_BED_CORNERS + +#if ENABLED(LEVEL_BED_CORNERS) + #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner +#endif + +/** + * Commands to execute at the end of G29 probing. + * Useful to retract or move the Z probe out of the way. + */ +//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" + + +// @section homing + +// The center of the bed is at (X=0, Y=0) +//#define BED_CENTER_AT_0_0 + +// Manually set the home position. Leave these undefined for automatic settings. +// For DELTA this is the top-center of the Cartesian print volume. +//#define MANUAL_X_HOME_POS 0 +//#define MANUAL_Y_HOME_POS 0 +//#define MANUAL_Z_HOME_POS 0 + +// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area. +// +// With this feature enabled: +// +// - Allow Z homing only after X and Y homing AND stepper drivers still enabled. +// - If stepper drivers time out, it will need X and Y homing again before Z homing. +// - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28). +// - Prevent Z homing when the Z probe is outside bed area. +// +//#define Z_SAFE_HOMING + +#if ENABLED(Z_SAFE_HOMING) + #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing when homing all axes (G28). + #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2) // Y point for Z homing when homing all axes (G28). +#endif + +// Homing speeds (mm/m) +#define HOMING_FEEDRATE_XY (50*60) +#define HOMING_FEEDRATE_Z (4*60) + +// Validate that endstops are triggered on homing moves +#define VALIDATE_HOMING_ENDSTOPS + +// @section calibrate + +/** + * Bed Skew Compensation + * + * This feature corrects for misalignment in the XYZ axes. + * + * Take the following steps to get the bed skew in the XY plane: + * 1. Print a test square (e.g., https://www.thingiverse.com/thing:2563185) + * 2. For XY_DIAG_AC measure the diagonal A to C + * 3. For XY_DIAG_BD measure the diagonal B to D + * 4. For XY_SIDE_AD measure the edge A to D + * + * Marlin automatically computes skew factors from these measurements. + * Skew factors may also be computed and set manually: + * + * - Compute AB : SQRT(2*AC*AC+2*BD*BD-4*AD*AD)/2 + * - XY_SKEW_FACTOR : TAN(PI/2-ACOS((AC*AC-AB*AB-AD*AD)/(2*AB*AD))) + * + * If desired, follow the same procedure for XZ and YZ. + * Use these diagrams for reference: + * + * Y Z Z + * ^ B-------C ^ B-------C ^ B-------C + * | / / | / / | / / + * | / / | / / | / / + * | A-------D | A-------D | A-------D + * +-------------->X +-------------->X +-------------->Y + * XY_SKEW_FACTOR XZ_SKEW_FACTOR YZ_SKEW_FACTOR + */ +//#define SKEW_CORRECTION + +#if ENABLED(SKEW_CORRECTION) + // Input all length measurements here: + #define XY_DIAG_AC 282.8427124746 + #define XY_DIAG_BD 282.8427124746 + #define XY_SIDE_AD 200 + + // Or, set the default skew factors directly here + // to override the above measurements: + #define XY_SKEW_FACTOR 0.0 + + //#define SKEW_CORRECTION_FOR_Z + #if ENABLED(SKEW_CORRECTION_FOR_Z) + #define XZ_DIAG_AC 282.8427124746 + #define XZ_DIAG_BD 282.8427124746 + #define YZ_DIAG_AC 282.8427124746 + #define YZ_DIAG_BD 282.8427124746 + #define YZ_SIDE_AD 200 + #define XZ_SKEW_FACTOR 0.0 + #define YZ_SKEW_FACTOR 0.0 + #endif + + // Enable this option for M852 to set skew at runtime + //#define SKEW_CORRECTION_GCODE +#endif + +//============================================================================= +//============================= Additional Features =========================== +//============================================================================= + +// @section extras + +/** + * EEPROM + * + * Persistent storage to preserve configurable settings across reboots. + * + * M500 - Store settings to EEPROM. + * M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes) + * M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.) + */ +#define EEPROM_SETTINGS // Persistent storage with M500 and M501 +//#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release! +#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM. +#if ENABLED(EEPROM_SETTINGS) + //#define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors. +#endif + +// +// Host Keepalive +// +// When enabled Marlin will send a busy status message to the host +// every couple of seconds when it can't accept commands. +// +#define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages +#define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113. +#define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating + +// +// M100 Free Memory Watcher +// +//#define M100_FREE_MEMORY_WATCHER // Add M100 (Free Memory Watcher) to debug memory usage + +// +// G20/G21 Inch mode support +// +//#define INCH_MODE_SUPPORT + +// +// M149 Set temperature units support +// +//#define TEMPERATURE_UNITS_SUPPORT + +// @section temperature + +// Preheat Constants +#define PREHEAT_1_LABEL "PLA" +#define PREHEAT_1_TEMP_HOTEND 180 +#define PREHEAT_1_TEMP_BED 70 +#define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255 + +#define PREHEAT_2_LABEL "ABS" +#define PREHEAT_2_TEMP_HOTEND 240 +#define PREHEAT_2_TEMP_BED 110 +#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255 + +/** + * Nozzle Park + * + * Park the nozzle at the given XYZ position on idle or G27. + * + * The "P" parameter controls the action applied to the Z axis: + * + * P0 (Default) If Z is below park Z raise the nozzle. + * P1 Raise the nozzle always to Z-park height. + * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS. + */ +//#define NOZZLE_PARK_FEATURE + +#if ENABLED(NOZZLE_PARK_FEATURE) + // Specify a park position as { X, Y, Z_raise } + #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 } + #define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis) + #define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers) +#endif + +/** + * Clean Nozzle Feature -- EXPERIMENTAL + * + * Adds the G12 command to perform a nozzle cleaning process. + * + * Parameters: + * P Pattern + * S Strokes / Repetitions + * T Triangles (P1 only) + * + * Patterns: + * P0 Straight line (default). This process requires a sponge type material + * at a fixed bed location. "S" specifies strokes (i.e. back-forth motions) + * between the start / end points. + * + * P1 Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the + * number of zig-zag triangles to do. "S" defines the number of strokes. + * Zig-zags are done in whichever is the narrower dimension. + * For example, "G12 P1 S1 T3" will execute: + * + * -- + * | (X0, Y1) | /\ /\ /\ | (X1, Y1) + * | | / \ / \ / \ | + * A | | / \ / \ / \ | + * | | / \ / \ / \ | + * | (X0, Y0) | / \/ \/ \ | (X1, Y0) + * -- +--------------------------------+ + * |________|_________|_________| + * T1 T2 T3 + * + * P2 Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE. + * "R" specifies the radius. "S" specifies the stroke count. + * Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT. + * + * Caveats: The ending Z should be the same as starting Z. + * Attention: EXPERIMENTAL. G-code arguments may change. + * + */ +//#define NOZZLE_CLEAN_FEATURE + +#if ENABLED(NOZZLE_CLEAN_FEATURE) + // Default number of pattern repetitions + #define NOZZLE_CLEAN_STROKES 12 + + // Default number of triangles + #define NOZZLE_CLEAN_TRIANGLES 3 + + // Specify positions as { X, Y, Z } + #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)} + #define NOZZLE_CLEAN_END_POINT { 100, 60, (Z_MIN_POS + 1) } + + // Circular pattern radius + #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5 + // Circular pattern circle fragments number + #define NOZZLE_CLEAN_CIRCLE_FN 10 + // Middle point of circle + #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT + + // Move the nozzle to the initial position after cleaning + #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z +#endif + +/** + * Print Job Timer + * + * Automatically start and stop the print job timer on M104/M109/M190. + * + * M104 (hotend, no wait) - high temp = none, low temp = stop timer + * M109 (hotend, wait) - high temp = start timer, low temp = stop timer + * M190 (bed, wait) - high temp = start timer, low temp = none + * + * The timer can also be controlled with the following commands: + * + * M75 - Start the print job timer + * M76 - Pause the print job timer + * M77 - Stop the print job timer + */ +#define PRINTJOB_TIMER_AUTOSTART + +/** + * Print Counter + * + * Track statistical data such as: + * + * - Total print jobs + * - Total successful print jobs + * - Total failed print jobs + * - Total time printing + * + * View the current statistics with M78. + */ +//#define PRINTCOUNTER + +//============================================================================= +//============================= LCD and SD support ============================ +//============================================================================= + +// @section lcd + +/** + * LCD LANGUAGE + * + * Select the language to display on the LCD. These languages are available: + * + * en, an, bg, ca, cz, da, de, el, el-gr, es, eu, fi, fr, gl, hr, it, + * jp-kana, ko_KR, nl, pl, pt, pt-br, ru, sk, tr, uk, zh_CN, zh_TW, test + * + * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cz':'Czech', 'da':'Danish', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'jp-kana':'Japanese', 'ko_KR':'Korean (South Korea)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'ru':'Russian', 'sk':'Slovak', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Traditional)', 'test':'TEST' } + */ +#define LCD_LANGUAGE en + +/** + * LCD Character Set + * + * Note: This option is NOT applicable to Graphical Displays. + * + * All character-based LCDs provide ASCII plus one of these + * language extensions: + * + * - JAPANESE ... the most common + * - WESTERN ... with more accented characters + * - CYRILLIC ... for the Russian language + * + * To determine the language extension installed on your controller: + * + * - Compile and upload with LCD_LANGUAGE set to 'test' + * - Click the controller to view the LCD menu + * - The LCD will display Japanese, Western, or Cyrillic text + * + * See http://marlinfw.org/docs/development/lcd_language.html + * + * :['JAPANESE', 'WESTERN', 'CYRILLIC'] + */ +#define DISPLAY_CHARSET_HD44780 JAPANESE + +/** + * Info Screen Style (0:Classic, 1:Prusa) + * + * :[0:'Classic', 1:'Prusa'] + */ +#define LCD_INFO_SCREEN_STYLE 0 + +/** + * SD CARD + * + * SD Card support is disabled by default. If your controller has an SD slot, + * you must uncomment the following option or it won't work. + * + */ +#define SDSUPPORT + +/** + * SD CARD: SPI SPEED + * + * Enable one of the following items for a slower SPI transfer speed. + * This may be required to resolve "volume init" errors. + */ +//#define SPI_SPEED SPI_HALF_SPEED +//#define SPI_SPEED SPI_QUARTER_SPEED +//#define SPI_SPEED SPI_EIGHTH_SPEED + +/** + * SD CARD: ENABLE CRC + * + * Use CRC checks and retries on the SD communication. + */ +//#define SD_CHECK_AND_RETRY + +/** + * LCD Menu Items + * + * Disable all menus and only display the Status Screen, or + * just remove some extraneous menu items to recover space. + */ +//#define NO_LCD_MENUS +//#define SLIM_LCD_MENUS + +// +// ENCODER SETTINGS +// +// This option overrides the default number of encoder pulses needed to +// produce one step. Should be increased for high-resolution encoders. +// +//#define ENCODER_PULSES_PER_STEP 4 + +// +// Use this option to override the number of step signals required to +// move between next/prev menu items. +// +//#define ENCODER_STEPS_PER_MENU_ITEM 1 + +/** + * Encoder Direction Options + * + * Test your encoder's behavior first with both options disabled. + * + * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION. + * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION. + * Reversed Value Editing only? Enable BOTH options. + */ + +// +// This option reverses the encoder direction everywhere. +// +// Set this option if CLOCKWISE causes values to DECREASE +// +//#define REVERSE_ENCODER_DIRECTION + +// +// This option reverses the encoder direction for navigating LCD menus. +// +// If CLOCKWISE normally moves DOWN this makes it go UP. +// If CLOCKWISE normally moves UP this makes it go DOWN. +// +//#define REVERSE_MENU_DIRECTION + +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + +// +// Individual Axis Homing +// +// Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu. +// +//#define INDIVIDUAL_AXIS_HOMING_MENU + +// +// SPEAKER/BUZZER +// +// If you have a speaker that can produce tones, enable it here. +// By default Marlin assumes you have a buzzer with a fixed frequency. +// +//#define SPEAKER + +// +// The duration and frequency for the UI feedback sound. +// Set these to 0 to disable audio feedback in the LCD menus. +// +// Note: Test audio output with the G-Code: +// M300 S P +// +//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 2 +//#define LCD_FEEDBACK_FREQUENCY_HZ 5000 + +//============================================================================= +//======================== LCD / Controller Selection ========================= +//======================== (Character-based LCDs) ========================= +//============================================================================= + +// +// RepRapDiscount Smart Controller. +// http://reprap.org/wiki/RepRapDiscount_Smart_Controller +// +// Note: Usually sold with a white PCB. +// +//#define REPRAP_DISCOUNT_SMART_CONTROLLER + +// +// Original RADDS LCD Display+Encoder+SDCardReader +// http://doku.radds.org/dokumentation/lcd-display/ +// +//#define RADDS_DISPLAY + +// +// ULTIMAKER Controller. +// +//#define ULTIMAKERCONTROLLER + +// +// ULTIPANEL as seen on Thingiverse. +// +//#define ULTIPANEL + +// +// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3) +// http://reprap.org/wiki/PanelOne +// +//#define PANEL_ONE + +// +// GADGETS3D G3D LCD/SD Controller +// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel +// +// Note: Usually sold with a blue PCB. +// +//#define G3D_PANEL + +// +// RigidBot Panel V1.0 +// http://www.inventapart.com/ +// +//#define RIGIDBOT_PANEL + +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// ANET and Tronxy 20x4 Controller +// +//#define ZONESTAR_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin. + // This LCD is known to be susceptible to electrical interference + // which scrambles the display. Pressing any button clears it up. + // This is a LCD2004 display with 5 analog buttons. + +// +// Generic 16x2, 16x4, 20x2, or 20x4 character-based LCD. +// +//#define ULTRA_LCD + +//============================================================================= +//======================== LCD / Controller Selection ========================= +//===================== (I2C and Shift-Register LCDs) ===================== +//============================================================================= + +// +// CONTROLLER TYPE: I2C +// +// Note: These controllers require the installation of Arduino's LiquidCrystal_I2C +// library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C +// + +// +// Elefu RA Board Control Panel +// http://www.elefu.com/index.php?route=product/product&product_id=53 +// +//#define RA_CONTROL_PANEL + +// +// Sainsmart (YwRobot) LCD Displays +// +// These require F.Malpartida's LiquidCrystal_I2C library +// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home +// +//#define LCD_SAINSMART_I2C_1602 +//#define LCD_SAINSMART_I2C_2004 + +// +// Generic LCM1602 LCD adapter +// +//#define LCM1602 + +// +// PANELOLU2 LCD with status LEDs, +// separate encoder and click inputs. +// +// Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later. +// For more info: https://github.com/lincomatic/LiquidTWI2 +// +// Note: The PANELOLU2 encoder click input can either be directly connected to +// a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1). +// +//#define LCD_I2C_PANELOLU2 + +// +// Panucatt VIKI LCD with status LEDs, +// integrated click & L/R/U/D buttons, separate encoder inputs. +// +//#define LCD_I2C_VIKI + +// +// CONTROLLER TYPE: Shift register panels +// + +// +// 2-wire Non-latching LCD SR from https://goo.gl/aJJ4sH +// LCD configuration: http://reprap.org/wiki/SAV_3D_LCD +// +//#define SAV_3DLCD + +// +// 3-wire SR LCD with strobe using 74HC4094 +// https://github.com/mikeshub/SailfishLCD +// Uses the code directly from Sailfish +// +//#define FF_INTERFACEBOARD + +//============================================================================= +//======================= LCD / Controller Selection ======================= +//========================= (Graphical LCDs) ======================== +//============================================================================= + +// +// CONTROLLER TYPE: Graphical 128x64 (DOGM) +// +// IMPORTANT: The U8glib library is required for Graphical Display! +// https://github.com/olikraus/U8glib_Arduino +// + +// +// RepRapDiscount FULL GRAPHIC Smart Controller +// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller +// +#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER + +// +// ReprapWorld Graphical LCD +// https://reprapworld.com/?products_details&products_id/1218 +// +//#define REPRAPWORLD_GRAPHICAL_LCD + +// +// Activate one of these if you have a Panucatt Devices +// Viki 2.0 or mini Viki with Graphic LCD +// http://panucatt.com +// +//#define VIKI2 +//#define miniVIKI + +// +// MakerLab Mini Panel with graphic +// controller and SD support - http://reprap.org/wiki/Mini_panel +// +//#define MINIPANEL + +// +// MaKr3d Makr-Panel with graphic controller and SD support. +// http://reprap.org/wiki/MaKr3d_MaKrPanel +// +//#define MAKRPANEL + +// +// Adafruit ST7565 Full Graphic Controller. +// https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/ +// +//#define ELB_FULL_GRAPHIC_CONTROLLER + +// +// BQ LCD Smart Controller shipped by +// default with the BQ Hephestos 2 and Witbox 2. +// +//#define BQ_LCD_SMART_CONTROLLER + +// +// Cartesio UI +// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// +//#define CARTESIO_UI + +// +// LCD for Melzi Card with Graphical LCD +// +//#define LCD_FOR_MELZI + +// +// Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder +// https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) +// +//#define ULTI_CONTROLLER + +// +// MKS MINI12864 with graphic controller and SD support +// https://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// FYSETC variant of the MINI12864 graphic controller with SD support +// https://wiki.fysetc.com/Mini12864_Panel/ +// +//#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default +//#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) +//#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// ANET and Tronxy Graphical Controller +// +// Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6 +// A clone of the RepRapDiscount full graphics display but with +// different pins/wiring (see pins_ANET_10.h). +// +//#define ANET_FULL_GRAPHICS_LCD + +// +// AZSMZ 12864 LCD with SD +// https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html +// +//#define AZSMZ_12864 + +// +// Silvergate GLCD controller +// http://github.com/android444/Silvergate +// +//#define SILVER_GATE_GLCD_CONTROLLER + +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + +//============================================================================= +//========================== Extensible UI Displays =========================== +//============================================================================= + +// +// DGUS Touch Display with DWIN OS +// +//#define DGUS_LCD + +// +// Touch-screen LCD for Malyan M200 printers +// +//#define MALYAN_LCD + +// +// Third-party or vendor-customized controller interfaces. +// Sources should be installed in 'src/lcd/extensible_ui'. +// +//#define EXTENSIBLE_UI + +//============================================================================= +//=============================== Graphical TFTs ============================== +//============================================================================= + +// +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) +// +//#define FSMC_GRAPHICAL_TFT + +//============================================================================= +//============================ Other Controllers ============================ +//============================================================================= + +// +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 +// +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif + +// +// RepRapWorld REPRAPWORLD_KEYPAD v1.1 +// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626 +// +// REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key +// is pressed, a value of 10.0 means 10mm per click. +// +//#define REPRAPWORLD_KEYPAD +//#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 + +//============================================================================= +//=============================== Extra Features ============================== +//============================================================================= + +// @section extras + +// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino +//#define FAST_PWM_FAN + +// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency +// which is not as annoying as with the hardware PWM. On the other hand, if this frequency +// is too low, you should also increment SOFT_PWM_SCALE. +//#define FAN_SOFT_PWM + +// Incrementing this by 1 will double the software PWM frequency, +// affecting heaters, and the fan if FAN_SOFT_PWM is enabled. +// However, control resolution will be halved for each increment; +// at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] +#define SOFT_PWM_SCALE 0 + +// If SOFT_PWM_SCALE is set to a value higher than 0, dithering can +// be used to mitigate the associated resolution loss. If enabled, +// some of the PWM cycles are stretched so on average the desired +// duty cycle is attained. +//#define SOFT_PWM_DITHER + +// Temperature status LEDs that display the hotend and bed temperature. +// If all hotends, bed temperature, and target temperature are under 54C +// then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis) +//#define TEMP_STAT_LEDS + +// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure +//#define SF_ARC_FIX + +// Support for the BariCUDA Paste Extruder +//#define BARICUDA + +// Support for BlinkM/CyzRgb +//#define BLINKM + +// Support for PCA9632 PWM LED driver +//#define PCA9632 + +// Support for PCA9533 PWM LED driver +// https://github.com/mikeshub/SailfishRGB_LED +//#define PCA9533 + +/** + * RGB LED / LED Strip Control + * + * Enable support for an RGB LED connected to 5V digital pins, or + * an RGB Strip connected to MOSFETs controlled by digital pins. + * + * Adds the M150 command to set the LED (or LED strip) color. + * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of + * luminance values can be set from 0 to 255. + * For Neopixel LED an overall brightness parameter is also available. + * + * *** CAUTION *** + * LED Strips require a MOSFET Chip between PWM lines and LEDs, + * as the Arduino cannot handle the current the LEDs will require. + * Failure to follow this precaution can destroy your Arduino! + * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * more current than the Arduino 5V linear regulator can produce. + * *** CAUTION *** + * + * LED Type. Enable only one of the following two options. + * + */ +#define RGB_LED +//#define RGBW_LED + +#if EITHER(RGB_LED, RGBW_LED) + //#define RGB_LED_R_PIN 34 + //#define RGB_LED_G_PIN 43 + //#define RGB_LED_B_PIN 35 + //#define RGB_LED_W_PIN -1 +#endif + +// Support for Adafruit Neopixel LED driver +//#define NEOPIXEL_LED +#if ENABLED(NEOPIXEL_LED) + #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. + #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) + //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup + + // Use a single Neopixel LED for static (background) lighting + //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use + //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W +#endif + +/** + * Printer Event LEDs + * + * During printing, the LEDs will reflect the printer status: + * + * - Gradually change from blue to violet as the heated bed gets to target temp + * - Gradually change from violet to red as the hotend gets to temperature + * - Change to white to illuminate work surface + * - Change to green once print has finished + * - Turn off after the print has finished and the user has pushed a button + */ +#if ANY(BLINKM, RGB_LED, RGBW_LED, PCA9632, PCA9533, NEOPIXEL_LED) + #define PRINTER_EVENT_LEDS +#endif + +/** + * R/C SERVO support + * Sponsored by TrinityLabs, Reworked by codexmas + */ + +/** + * Number of servos + * + * For some servo-related options NUM_SERVOS will be set automatically. + * Set this manually if there are extra servos needing manual control. + * Leave undefined or set to 0 to entirely disable the servo subsystem. + */ +//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command + +// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. +// 300ms is a good value but you can try less delay. +// If the servo can't reach the requested position, increase it. +#define SERVO_DELAY { 300 } + +// Only power servos during movement, otherwise leave off to prevent jitter +//#define DEACTIVATE_SERVOS_AFTER_MOVE + +// Allow servo angle to be edited and saved to EEPROM +//#define EDITABLE_SERVO_ANGLES + +/** + * Sometimes after inserting the SD card settings get lost. + * This option reloads settings when the SD card is inserted. + */ +#define SD_RELOAD_SETTINGS diff --git a/config/examples/Fysetc/CHEETAH/Configuration_adv.h b/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h similarity index 99% rename from config/examples/Fysetc/CHEETAH/Configuration_adv.h rename to config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h index 9aca20d7f9..94f4e7e9fd 100644 --- a/config/examples/Fysetc/CHEETAH/Configuration_adv.h +++ b/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h @@ -851,6 +851,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -906,13 +909,13 @@ // Reverse SD sort to show "more recent" files first, according to the card's FAT. // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended. - #define SDCARD_RATHERRECENTFIRST + //#define SDCARD_RATHERRECENTFIRST #define SD_MENU_CONFIRM_START // Confirm the selected SD file before printing //#define MENU_ADDAUTOSTART // Add a menu option to run auto#.g files - #define EVENT_GCODE_SD_STOP "G28XY" // G-code to run on Stop Print (e.g., "G28XY" or "G27") + #define EVENT_GCODE_SD_STOP "M21" // G-code to run on Stop Print (e.g., "G28XY" or "G27") /** * Continue after Power-Loss (Creality3D) @@ -1135,6 +1138,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1368,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1636,7 +1643,7 @@ #define INTERPOLATE true // Interpolate X/Y/Z_MICROSTEPS to 256 #if AXIS_IS_TMC(X) - #define X_CURRENT 650 // (mA) RMS current. Multiply by 1.414 for peak current. + #define X_CURRENT 700 // (mA) RMS current. Multiply by 1.414 for peak current. #define X_MICROSTEPS 16 // 0..256 #define X_RSENSE 0.11 #endif @@ -1648,7 +1655,7 @@ #endif #if AXIS_IS_TMC(Y) - #define Y_CURRENT 650 + #define Y_CURRENT 500 #define Y_MICROSTEPS 16 #define Y_RSENSE 0.11 #endif @@ -1749,6 +1756,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 1 @@ -2434,6 +2444,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Fysetc/CHEETAH/Configuration.h b/config/examples/FYSETC/Cheetah/BLTouch/Configuration.h similarity index 95% rename from config/examples/Fysetc/CHEETAH/Configuration.h rename to config/examples/FYSETC/Cheetah/BLTouch/Configuration.h index ad7a948c91..cbfe89323d 100644 --- a/config/examples/Fysetc/CHEETAH/Configuration.h +++ b/config/examples/FYSETC/Cheetah/BLTouch/Configuration.h @@ -104,7 +104,7 @@ * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ -#define SERIAL_PORT 1 // libmaple USB 1, old:0 +#define SERIAL_PORT 1 // libmaple 0 for USB ,1 for serial /** * Select a secondary serial port on the board to use for communication with the host. @@ -150,7 +150,7 @@ #define EXTRUDERS 1 // Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc. -#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0 +#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 // For Cyclops or any "multi-extruder" that shares a single nozzle. //#define SINGLENOZZLE @@ -258,16 +258,7 @@ */ //#define MAGNETIC_SWITCHING_TOOLHEAD -/** - * Electromagnetic Switching Toolhead - * - * Parking for CoreXY / HBot kinematics. - * Toolheads are parked at one edge and held with an electromagnet. - * Supports more than 2 Toolheads. See https://youtu.be/JolbsAKTKf4 - */ -//#define ELECTROMAGNETIC_SWITCHING_TOOLHEAD - -#if ANY(SWITCHING_TOOLHEAD, MAGNETIC_SWITCHING_TOOLHEAD, ELECTROMAGNETIC_SWITCHING_TOOLHEAD) +#if EITHER(SWITCHING_TOOLHEAD, MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_POS 235 // (mm) Y position of the toolhead dock #define SWITCHING_TOOLHEAD_Y_SECURITY 10 // (mm) Security distance Y axis #define SWITCHING_TOOLHEAD_Y_CLEAR 60 // (mm) Minimum distance from dock for unobstructed X axis @@ -277,7 +268,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -312,20 +310,22 @@ // @section machine /** - * Power Supply Control + * Select your power supply here. Use 0 if you haven't connected the PS_ON_PIN * - * Enable and connect the power supply to the PS_ON_PIN. - * Specify whether the power supply is active HIGH or active LOW. + * 0 = No Power Switch + * 1 = ATX + * 2 = X-Box 360 203Watts (the blue wire connected to PS_ON and the red wire to VCC) + * + * :{ 0:'No power switch', 1:'ATX', 2:'X-Box 360' } */ -//#define PSU_CONTROL -//#define PSU_NAME "Power Supply" +#define POWER_SUPPLY 0 -#if ENABLED(PSU_CONTROL) - #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2) +#if POWER_SUPPLY > 0 + // Enable this option to leave the PSU off at startup. + // Power to steppers and heaters will need to be turned on with M80. + //#define PS_DEFAULT_OFF - //#define PS_DEFAULT_OFF // Keep power off until enabled directly with M80 - - //#define AUTO_POWER_CONTROL // Enable automatic control of the PS_ON pin + //#define AUTO_POWER_CONTROL // Enable automatic control of the PS_ON pin #if ENABLED(AUTO_POWER_CONTROL) #define AUTO_POWER_FANS // Turn on PSU if fans need power #define AUTO_POWER_E_FANS @@ -335,6 +335,7 @@ //#define AUTO_POWER_CHAMBER_TEMP 30 // (°C) Turn on PSU over this temperature #define POWER_TIMEOUT 30 #endif + #endif // @section temperature @@ -467,10 +468,15 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it + //PID for Makerlab J-head + #define DEFAULT_Kp 21.73 + #define DEFAULT_Ki 1.54 + #define DEFAULT_Kd 76.55 + // Ultimaker - #define DEFAULT_Kp 22.2 - #define DEFAULT_Ki 1.08 - #define DEFAULT_Kd 114 + //#define DEFAULT_Kp 22.2 + //#define DEFAULT_Ki 1.08 + //#define DEFAULT_Kd 114 // MakerGear //#define DEFAULT_Kp 7.0 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -717,7 +723,7 @@ * Override with M203 * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] */ -#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 } +#define DEFAULT_MAX_FEEDRATE { 500, 500, 5, 25 } /** * Default Max Acceleration (change/s) change = mm/s @@ -725,7 +731,7 @@ * Override with M201 * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] */ -#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 } +#define DEFAULT_MAX_ACCELERATION { 500, 500, 100, 5000 } /** * Default Acceleration (change/s) change = mm/s @@ -735,13 +741,19 @@ * M204 R Retract Acceleration * M204 T Travel Acceleration */ -#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves -#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts -#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves +#define DEFAULT_ACCELERATION 500 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 500 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 500 // X, Y, Z acceleration for travel (non printing) moves -// -// Use Junction Deviation instead of traditional Jerk Limiting -// +/** + * Junction Deviation + * + * Use Junction Deviation instead of traditional Jerk Limiting + * + * See: + * https://reprap.org/forum/read.php?1,739819 + * http://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html + */ //#define JUNCTION_DEVIATION #if ENABLED(JUNCTION_DEVIATION) #define JUNCTION_DEVIATION_MM 0.02 // (mm) Distance from real junction edge @@ -837,7 +849,7 @@ /** * The BLTouch probe uses a Hall effect sensor and emulates a servo. */ -//#define BLTOUCH +#define BLTOUCH /** * Touch-MI Probe by hotends.fr @@ -893,9 +905,9 @@ * O-- FRONT --+ * (0,0) */ -#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle] -#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle] -#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle] +#define X_PROBE_OFFSET_FROM_EXTRUDER -44 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER -6 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER -3.9 // Z offset: -below +above [the nozzle] // Certain types of probes need to stay away from edges #define MIN_PROBE_EDGE 10 @@ -935,8 +947,8 @@ * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle. * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle. */ -#define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow -#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points +#define Z_CLEARANCE_DEPLOY_PROBE 15 // Z Clearance for Deploy/Stow +#define Z_CLEARANCE_BETWEEN_PROBES 10 // Z Clearance between probe points #define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes //#define Z_AFTER_PROBING 5 // Z position after probing is done @@ -1035,7 +1047,7 @@ #define Z_MIN_POS 0 #define X_MAX_POS X_BED_SIZE #define Y_MAX_POS Y_BED_SIZE -#define Z_MAX_POS 250 +#define Z_MAX_POS 260 /** * Software Endstops @@ -1308,7 +1320,7 @@ // - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28). // - Prevent Z homing when the Z probe is outside bed area. // -//#define Z_SAFE_HOMING +#define Z_SAFE_HOMING #if ENABLED(Z_SAFE_HOMING) #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing when homing all axes (G28). @@ -1394,7 +1406,7 @@ * M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes) * M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.) */ -//#define EEPROM_SETTINGS // Persistent storage with M500 and M501 +#define EEPROM_SETTINGS // Persistent storage with M500 and M501 //#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release! #define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM. #if ENABLED(EEPROM_SETTINGS) @@ -1675,6 +1687,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1981,6 +2001,11 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2006,17 +2031,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2112,8 +2144,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup @@ -2162,3 +2196,9 @@ // Allow servo angle to be edited and saved to EEPROM //#define EDITABLE_SERVO_ANGLES + +/** + * Sometimes after inserting the SD card settings get lost. + * This option reloads settings when the SD card is inserted. + */ +#define SD_RELOAD_SETTINGS diff --git a/config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h b/config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h new file mode 100644 index 0000000000..f59721ae05 --- /dev/null +++ b/config/examples/FYSETC/Cheetah/BLTouch/Configuration_adv.h @@ -0,0 +1,2561 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Configuration_adv.h + * + * Advanced settings. + * Only change these if you know exactly what you're doing. + * Some of these settings can damage your printer if improperly set! + * + * Basic settings can be found in Configuration.h + * + */ +#define CONFIGURATION_ADV_H_VERSION 020000 + +// @section temperature + +//=========================================================================== +//=============================Thermal Settings ============================ +//=========================================================================== + +// +// Custom Thermistor 1000 parameters +// +#if TEMP_SENSOR_0 == 1000 + #define HOTEND0_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND0_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND0_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_1 == 1000 + #define HOTEND1_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND1_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND1_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_2 == 1000 + #define HOTEND2_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND2_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND2_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_3 == 1000 + #define HOTEND3_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND3_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND3_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_4 == 1000 + #define HOTEND4_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND4_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND4_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_5 == 1000 + #define HOTEND5_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND5_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND5_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_BED == 1000 + #define BED_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define BED_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define BED_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_CHAMBER == 1000 + #define CHAMBER_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define CHAMBER_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define CHAMBER_BETA 3950 // Beta value +#endif + +// +// Hephestos 2 24V heated bed upgrade kit. +// https://store.bq.com/en/heated-bed-kit-hephestos2 +// +//#define HEPHESTOS2_HEATED_BED_KIT +#if ENABLED(HEPHESTOS2_HEATED_BED_KIT) + #undef TEMP_SENSOR_BED + #define TEMP_SENSOR_BED 70 + #define HEATER_BED_INVERTING true +#endif + +/** + * Heated Chamber settings + */ +#if TEMP_SENSOR_CHAMBER + #define CHAMBER_MINTEMP 5 + #define CHAMBER_MAXTEMP 60 + #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target + //#define CHAMBER_LIMIT_SWITCHING + //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin + //#define HEATER_CHAMBER_INVERTING false +#endif + +#if DISABLED(PIDTEMPBED) + #define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control + #if ENABLED(BED_LIMIT_SWITCHING) + #define BED_HYSTERESIS 2 // Only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS + #endif +#endif + +/** + * Thermal Protection provides additional protection to your printer from damage + * and fire. Marlin always includes safe min and max temperature ranges which + * protect against a broken or disconnected thermistor wire. + * + * The issue: If a thermistor falls out, it will report the much lower + * temperature of the air in the room, and the the firmware will keep + * the heater on. + * + * The solution: Once the temperature reaches the target, start observing. + * If the temperature stays too far below the target (hysteresis) for too + * long (period), the firmware will halt the machine as a safety precaution. + * + * If you get false positives for "Thermal Runaway", increase + * THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD + */ +#if ENABLED(THERMAL_PROTECTION_HOTENDS) + #define THERMAL_PROTECTION_PERIOD 40 // Seconds + #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius + + //#define ADAPTIVE_FAN_SLOWING // Slow part cooling fan if temperature drops + #if BOTH(ADAPTIVE_FAN_SLOWING, PIDTEMP) + //#define NO_FAN_SLOWING_IN_PID_TUNING // Don't slow fan speed during M303 + #endif + + /** + * Whenever an M104, M109, or M303 increases the target temperature, the + * firmware will wait for the WATCH_TEMP_PERIOD to expire. If the temperature + * hasn't increased by WATCH_TEMP_INCREASE degrees, the machine is halted and + * requires a hard reset. This test restarts with any M104/M109/M303, but only + * if the current temperature is far enough below the target for a reliable + * test. + * + * If you get false positives for "Heating failed", increase WATCH_TEMP_PERIOD + * and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set + * below 2. + */ + #define WATCH_TEMP_PERIOD 120 // Seconds + #define WATCH_TEMP_INCREASE 2 // Degrees Celsius +#endif + +/** + * Thermal Protection parameters for the bed are just as above for hotends. + */ +#if ENABLED(THERMAL_PROTECTION_BED) + #define THERMAL_PROTECTION_BED_PERIOD 60 // Seconds + #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius + + /** + * As described above, except for the bed (M140/M190/M303). + */ + #define WATCH_BED_TEMP_PERIOD 100 // Seconds + #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius +#endif + +/** + * Thermal Protection parameters for the heated chamber. + */ +#if ENABLED(THERMAL_PROTECTION_CHAMBER) + #define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds + #define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius + + /** + * Heated chamber watch settings (M141/M191). + */ + #define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds + #define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius +#endif + +#if ENABLED(PIDTEMP) + // Add an experimental additional term to the heater power, proportional to the extrusion speed. + // A well-chosen Kc value should add just enough power to melt the increased material volume. + //#define PID_EXTRUSION_SCALING + #if ENABLED(PID_EXTRUSION_SCALING) + #define DEFAULT_Kc (100) //heating power=Kc*(e_speed) + #define LPQ_MAX_LEN 50 + #endif +#endif + +/** + * Automatic Temperature: + * The hotend target temperature is calculated by all the buffered lines of gcode. + * The maximum buffered steps/sec of the extruder motor is called "se". + * Start autotemp mode with M109 S B F + * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by + * mintemp and maxtemp. Turn this off by executing M109 without F* + * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp. + * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode + */ +#define AUTOTEMP +#if ENABLED(AUTOTEMP) + #define AUTOTEMP_OLDWEIGHT 0.98 +#endif + +// Show extra position information in M114 +//#define M114_DETAIL + +// Show Temperature ADC value +// Enable for M105 to include ADC values read from temperature sensors. +//#define SHOW_TEMP_ADC_VALUES + +/** + * High Temperature Thermistor Support + * + * Thermistors able to support high temperature tend to have a hard time getting + * good readings at room and lower temperatures. This means HEATER_X_RAW_LO_TEMP + * will probably be caught when the heating element first turns on during the + * preheating process, which will trigger a min_temp_error as a safety measure + * and force stop everything. + * To circumvent this limitation, we allow for a preheat time (during which, + * min_temp_error won't be triggered) and add a min_temp buffer to handle + * aberrant readings. + * + * If you want to enable this feature for your hotend thermistor(s) + * uncomment and set values > 0 in the constants below + */ + +// The number of consecutive low temperature errors that can occur +// before a min_temp_error is triggered. (Shouldn't be more than 10.) +//#define MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED 0 + +// The number of milliseconds a hotend will preheat before starting to check +// the temperature. This value should NOT be set to the time it takes the +// hot end to reach the target temperature, but the time it takes to reach +// the minimum temperature your thermistor can read. The lower the better/safer. +// This shouldn't need to be more than 30 seconds (30000) +//#define MILLISECONDS_PREHEAT_TIME 0 + +// @section extruder + +// Extruder runout prevention. +// If the machine is idle and the temperature over MINTEMP +// then extrude some filament every couple of SECONDS. +//#define EXTRUDER_RUNOUT_PREVENT +#if ENABLED(EXTRUDER_RUNOUT_PREVENT) + #define EXTRUDER_RUNOUT_MINTEMP 190 + #define EXTRUDER_RUNOUT_SECONDS 30 + #define EXTRUDER_RUNOUT_SPEED 1500 // (mm/m) + #define EXTRUDER_RUNOUT_EXTRUDE 5 // (mm) +#endif + +// @section temperature + +// Calibration for AD595 / AD8495 sensor to adjust temperature measurements. +// The final temperature is calculated as (measuredTemp * GAIN) + OFFSET. +#define TEMP_SENSOR_AD595_OFFSET 0.0 +#define TEMP_SENSOR_AD595_GAIN 1.0 +#define TEMP_SENSOR_AD8495_OFFSET 0.0 +#define TEMP_SENSOR_AD8495_GAIN 1.0 + +/** + * Controller Fan + * To cool down the stepper drivers and MOSFETs. + * + * The fan will turn on automatically whenever any stepper is enabled + * and turn off after a set period after all steppers are turned off. + */ +//#define USE_CONTROLLER_FAN +#if ENABLED(USE_CONTROLLER_FAN) + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled + #define CONTROLLERFAN_SPEED 255 // 255 == full speed +#endif + +// When first starting the main fan, run it at full speed for the +// given number of milliseconds. This gets the fan spinning reliably +// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) +//#define FAN_KICKSTART_TIME 100 + +/** + * PWM Fan Scaling + * + * Define the min/max speeds for PWM fans (as set with M106). + * + * With these options the M106 0-255 value range is scaled to a subset + * to ensure that the fan has enough power to spin, or to run lower + * current fans with higher current. (e.g., 5V/12V fans with 12V/24V) + * Value 0 always turns off the fan. + * + * Define one or both of these to override the default 0-255 range. + */ +//#define FAN_MIN_PWM 50 +//#define FAN_MAX_PWM 128 + +/** + * FAST PWM FAN Settings + * + * Use to change the FAST FAN PWM frequency (if enabled in Configuration.h) + * Combinations of PWM Modes, prescale values and TOP resolutions are used internally to produce a + * frequency as close as possible to the desired frequency. + * + * FAST_PWM_FAN_FREQUENCY [undefined by default] + * Set this to your desired frequency. + * If left undefined this defaults to F = F_CPU/(2*255*1) + * ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers + * These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required + * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior. + * + * USE_OCR2A_AS_TOP [undefined by default] + * Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2: + * 16MHz MCUs: [62.5KHz, 31.4KHz (default), 7.8KHz, 3.92KHz, 1.95KHz, 977Hz, 488Hz, 244Hz, 60Hz, 122Hz, 30Hz] + * 20MHz MCUs: [78.1KHz, 39.2KHz (default), 9.77KHz, 4.9KHz, 2.44KHz, 1.22KHz, 610Hz, 305Hz, 153Hz, 76Hz, 38Hz] + * A greater range can be achieved by enabling USE_OCR2A_AS_TOP. But note that this option blocks the use of + * PWM on pin OC2A. Only use this option if you don't need PWM on 0C2A. (Check your schematic.) + * USE_OCR2A_AS_TOP sacrifices duty cycle control resolution to achieve this broader range of frequencies. + */ +#if ENABLED(FAST_PWM_FAN) + //#define FAST_PWM_FAN_FREQUENCY 31400 + //#define USE_OCR2A_AS_TOP +#endif + +// @section extruder + +/** + * Extruder cooling fans + * + * Extruder auto fans automatically turn on when their extruders' + * temperatures go above EXTRUDER_AUTO_FAN_TEMPERATURE. + * + * Your board's pins file specifies the recommended pins. Override those here + * or set to -1 to disable completely. + * + * Multiple extruders can be assigned to the same pin in which case + * the fan will turn on when any selected extruder is above the threshold. + */ +#define E0_AUTO_FAN_PIN -1 +#define E1_AUTO_FAN_PIN -1 +#define E2_AUTO_FAN_PIN -1 +#define E3_AUTO_FAN_PIN -1 +#define E4_AUTO_FAN_PIN -1 +#define E5_AUTO_FAN_PIN -1 +#define CHAMBER_AUTO_FAN_PIN -1 + +#define EXTRUDER_AUTO_FAN_TEMPERATURE 50 +#define EXTRUDER_AUTO_FAN_SPEED 255 // 255 == full speed +#define CHAMBER_AUTO_FAN_TEMPERATURE 30 +#define CHAMBER_AUTO_FAN_SPEED 255 + +/** + * Part-Cooling Fan Multiplexer + * + * This feature allows you to digitally multiplex the fan output. + * The multiplexer is automatically switched at tool-change. + * Set FANMUX[012]_PINs below for up to 2, 4, or 8 multiplexed fans. + */ +#define FANMUX0_PIN -1 +#define FANMUX1_PIN -1 +#define FANMUX2_PIN -1 + +/** + * M355 Case Light on-off / brightness + */ +//#define CASE_LIGHT_ENABLE +#if ENABLED(CASE_LIGHT_ENABLE) + //#define CASE_LIGHT_PIN 4 // Override the default pin if needed + #define INVERT_CASE_LIGHT false // Set true if Case Light is ON when pin is LOW + #define CASE_LIGHT_DEFAULT_ON true // Set default power-up state on + #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105 // Set default power-up brightness (0-255, requires PWM pin) + //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu + //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. + //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) + #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } + #endif +#endif + +// @section homing + +// If you want endstops to stay on (by default) even when not homing +// enable this option. Override at any time with M120, M121. +//#define ENDSTOPS_ALWAYS_ON_DEFAULT + +// @section extras + +//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats. + +// Employ an external closed loop controller. Override pins here if needed. +//#define EXTERNAL_CLOSED_LOOP_CONTROLLER +#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER) + //#define CLOSED_LOOP_ENABLE_PIN -1 + //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1 +#endif + +/** + * Dual Steppers / Dual Endstops + * + * This section will allow you to use extra E drivers to drive a second motor for X, Y, or Z axes. + * + * For example, set X_DUAL_STEPPER_DRIVERS setting to use a second motor. If the motors need to + * spin in opposite directions set INVERT_X2_VS_X_DIR. If the second motor needs its own endstop + * set X_DUAL_ENDSTOPS. This can adjust for "racking." Use X2_USE_ENDSTOP to set the endstop plug + * that should be used for the second endstop. Extra endstops will appear in the output of 'M119'. + * + * Use X_DUAL_ENDSTOP_ADJUSTMENT to adjust for mechanical imperfection. After homing both motors + * this offset is applied to the X2 motor. To find the offset home the X axis, and measure the error + * in X2. Dual endstop offsets can be set at runtime with 'M666 X Y Z'. + */ + +//#define X_DUAL_STEPPER_DRIVERS +#if ENABLED(X_DUAL_STEPPER_DRIVERS) + #define INVERT_X2_VS_X_DIR true // Set 'true' if X motors should rotate in opposite directions + //#define X_DUAL_ENDSTOPS + #if ENABLED(X_DUAL_ENDSTOPS) + #define X2_USE_ENDSTOP _XMAX_ + #define X_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Y_DUAL_STEPPER_DRIVERS +#if ENABLED(Y_DUAL_STEPPER_DRIVERS) + #define INVERT_Y2_VS_Y_DIR true // Set 'true' if Y motors should rotate in opposite directions + //#define Y_DUAL_ENDSTOPS + #if ENABLED(Y_DUAL_ENDSTOPS) + #define Y2_USE_ENDSTOP _YMAX_ + #define Y_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Z_DUAL_STEPPER_DRIVERS +#if ENABLED(Z_DUAL_STEPPER_DRIVERS) + //#define Z_DUAL_ENDSTOPS + #if ENABLED(Z_DUAL_ENDSTOPS) + #define Z2_USE_ENDSTOP _XMAX_ + #define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Z_TRIPLE_STEPPER_DRIVERS +#if ENABLED(Z_TRIPLE_STEPPER_DRIVERS) + //#define Z_TRIPLE_ENDSTOPS + #if ENABLED(Z_TRIPLE_ENDSTOPS) + #define Z2_USE_ENDSTOP _XMAX_ + #define Z3_USE_ENDSTOP _YMAX_ + #define Z_TRIPLE_ENDSTOPS_ADJUSTMENT2 0 + #define Z_TRIPLE_ENDSTOPS_ADJUSTMENT3 0 + #endif +#endif + +/** + * Dual X Carriage + * + * This setup has two X carriages that can move independently, each with its own hotend. + * The carriages can be used to print an object with two colors or materials, or in + * "duplication mode" it can print two identical or X-mirrored objects simultaneously. + * The inactive carriage is parked automatically to prevent oozing. + * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. + * By default the X2 stepper is assigned to the first unused E plug on the board. + * + * The following Dual X Carriage modes can be selected with M605 S: + * + * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel + * results as long as it supports dual X-carriages. (M605 S0) + * + * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so + * that additional slicer support is not required. (M605 S1) + * + * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with + * the first X-carriage and extruder, to print 2 copies of the same object at the same time. + * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and + * follow with M605 S2 to initiate duplicated movement. + * + * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates + * the movement of the first except the second extruder is reversed in the X axis. + * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and + * follow with M605 S3 to initiate mirrored movement. + */ +//#define DUAL_X_CARRIAGE +#if ENABLED(DUAL_X_CARRIAGE) + #define X1_MIN_POS X_MIN_POS // Set to X_MIN_POS + #define X1_MAX_POS X_BED_SIZE // Set a maximum so the first X-carriage can't hit the parked second X-carriage + #define X2_MIN_POS 80 // Set a minimum to ensure the second X-carriage can't hit the parked first X-carriage + #define X2_MAX_POS 353 // Set this to the distance between toolheads when both heads are homed + #define X2_HOME_DIR 1 // Set to 1. The second X-carriage always homes to the maximum endstop position + #define X2_HOME_POS X2_MAX_POS // Default X2 home position. Set to X2_MAX_POS. + // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software + // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops + // without modifying the firmware (through the "M218 T1 X???" command). + // Remember: you should set the second extruder x-offset to 0 in your slicer. + + // This is the default power-up mode which can be later using M605. + #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_AUTO_PARK_MODE + + // Default x offset in duplication mode (typically set to half print bed width) + #define DEFAULT_DUPLICATION_X_OFFSET 100 + +#endif // DUAL_X_CARRIAGE + +// Activate a solenoid on the active extruder with M380. Disable all with M381. +// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid. +//#define EXT_SOLENOID + +// @section homing + +// Homing hits each endstop, retracts by these distances, then does a slower bump. +#define X_HOME_BUMP_MM 5 +#define Y_HOME_BUMP_MM 5 +#define Z_HOME_BUMP_MM 2 +#define HOMING_BUMP_DIVISOR { 2, 2, 4 } // Re-Bump Speed Divisor (Divides the Homing Feedrate) +//#define QUICK_HOME // If homing includes X and Y, do a diagonal move initially +//#define HOMING_BACKOFF_MM { 2, 2, 2 } // (mm) Move away from the endstops after homing + +// When G28 is called, this option will make Y home before X +//#define HOME_Y_BEFORE_X + +// Enable this if X or Y can't home without homing the other axis first. +//#define CODEPENDENT_XY_HOMING + +#if ENABLED(BLTOUCH) + /** + * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES + * Do not activate settings that the probe might not understand. Clones might misunderstand + * advanced commands. + * + * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then + * check the wiring of the BROWN, RED and ORANGE wires. + * + * Note: If the trigger signal of your probe is not being recognized, it has been very often + * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable" + * like they would be with a real switch. So please check the wiring first. + * + * Settings for all BLTouch and clone probes: + */ + + // Safety: The probe needs time to recognize the command. + // Minimum command delay (ms). Enable and increase if needed. + //#define BLTOUCH_DELAY 500 + + /** + * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones: + */ + + // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful + // in special cases, like noisy or filtered input configurations. + //#define BLTOUCH_FORCE_SW_MODE + + /** + * Settings for BLTouch Smart 3.0 and 3.1 + * Summary: + * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes + * - High-Speed mode + * - Disable LCD voltage options + */ + + /** + * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller! + * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup. + * If disabled, OD mode is the hard-coded default on 3.0 + * On startup, Marlin will compare its eeprom to this vale. If the selected mode + * differs, a mode set eeprom write will be completed at initialization. + * Use the option below to force an eeprom write to a V3.1 probe regardless. + */ + //#define BLTOUCH_SET_5V_MODE + + /** + * Safety: Activate if connecting a probe with an unknown voltage mode. + * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0 + * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write ) + * To preserve the life of the probe, use this once then turn it off and re-flash. + */ + //#define BLTOUCH_FORCE_MODE_SET + + /** + * Use "HIGH SPEED" mode for probing. + * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems. + * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function + * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state. + */ + //#define BLTOUCH_HS_MODE + + // Safety: Enable voltage mode settings in the LCD menu. + //#define BLTOUCH_LCD_VOLTAGE_MENU + +#endif // BLTOUCH + +/** + * Z Steppers Auto-Alignment + * Add the G34 command to align multiple Z steppers using a bed probe. + */ +//#define Z_STEPPER_AUTO_ALIGN +#if ENABLED(Z_STEPPER_AUTO_ALIGN) + // Define probe X and Y positions for Z1, Z2 [, Z3] + #define Z_STEPPER_ALIGN_X { 10, 150, 290 } + #define Z_STEPPER_ALIGN_Y { 290, 10, 290 } + // Set number of iterations to align + #define Z_STEPPER_ALIGN_ITERATIONS 3 + // Enable to restore leveling setup after operation + #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + + // Use the amplification factor to de-/increase correction step. + // In case the stepper (spindle) position is further out than the test point + // Use a value > 1. NOTE: This may cause instability + #define Z_STEPPER_ALIGN_AMP 1.0 + // Stop criterion. If the accuracy is better than this stop iterating early + #define Z_STEPPER_ALIGN_ACC 0.02 +#endif + +// @section machine + +#define AXIS_RELATIVE_MODES { false, false, false, false } + +// Add a Duplicate option for well-separated conjoined nozzles +//#define MULTI_NOZZLE_DUPLICATION + +// By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step. +#define INVERT_X_STEP_PIN false +#define INVERT_Y_STEP_PIN false +#define INVERT_Z_STEP_PIN false +#define INVERT_E_STEP_PIN false + +// Default stepper release if idle. Set to 0 to deactivate. +// Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true. +// Time can be set by M18 and M84. +#define DEFAULT_STEPPER_DEACTIVE_TIME 120 +#define DISABLE_INACTIVE_X true +#define DISABLE_INACTIVE_Y true +#define DISABLE_INACTIVE_Z true // Set to false if the nozzle will fall down on your printed part when print has finished. +#define DISABLE_INACTIVE_E true + +#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate +#define DEFAULT_MINTRAVELFEEDRATE 0.0 + +//#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated + +// @section lcd + +#if EITHER(ULTIPANEL, EXTENSIBLE_UI) + #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #if ENABLED(ULTIPANEL) + #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" + #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen + #endif +#endif + +// @section extras + +// minimum time in microseconds that a movement needs to take if the buffer is emptied. +#define DEFAULT_MINSEGMENTTIME 20000 + +// If defined the movements slow down when the look ahead buffer is only half full +#define SLOWDOWN + +// Frequency limit +// See nophead's blog for more info +// Not working O +//#define XY_FREQUENCY_LIMIT 15 + +// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end +// of the buffer and all stops. This should not be much greater than zero and should only be changed +// if unwanted behavior is observed on a user's machine when running at very slow speeds. +#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s) + +// +// Backlash Compensation +// Adds extra movement to axes on direction-changes to account for backlash. +// +//#define BACKLASH_COMPENSATION +#if ENABLED(BACKLASH_COMPENSATION) + // Define values for backlash distance and correction. + // If BACKLASH_GCODE is enabled these values are the defaults. + #define BACKLASH_DISTANCE_MM { 0, 0, 0 } // (mm) + #define BACKLASH_CORRECTION 0.0 // 0.0 = no correction; 1.0 = full correction + + // Set BACKLASH_SMOOTHING_MM to spread backlash correction over multiple segments + // to reduce print artifacts. (Enabling this is costly in memory and computation!) + //#define BACKLASH_SMOOTHING_MM 3 // (mm) + + // Add runtime configuration and tuning of backlash values (M425) + //#define BACKLASH_GCODE + + #if ENABLED(BACKLASH_GCODE) + // Measure the Z backlash when probing (G29) and set with "M425 Z" + #define MEASURE_BACKLASH_WHEN_PROBING + + #if ENABLED(MEASURE_BACKLASH_WHEN_PROBING) + // When measuring, the probe will move up to BACKLASH_MEASUREMENT_LIMIT + // mm away from point of contact in BACKLASH_MEASUREMENT_RESOLUTION + // increments while checking for the contact to be broken. + #define BACKLASH_MEASUREMENT_LIMIT 0.5 // (mm) + #define BACKLASH_MEASUREMENT_RESOLUTION 0.005 // (mm) + #define BACKLASH_MEASUREMENT_FEEDRATE Z_PROBE_SPEED_SLOW // (mm/m) + #endif + #endif +#endif + +/** + * Automatic backlash, position and hotend offset calibration + * + * Enable G425 to run automatic calibration using an electrically- + * conductive cube, bolt, or washer mounted on the bed. + * + * G425 uses the probe to touch the top and sides of the calibration object + * on the bed and measures and/or correct positional offsets, axis backlash + * and hotend offsets. + * + * Note: HOTEND_OFFSET and CALIBRATION_OBJECT_CENTER must be set to within + * ±5mm of true values for G425 to succeed. + */ +//#define CALIBRATION_GCODE +#if ENABLED(CALIBRATION_GCODE) + + #define CALIBRATION_MEASUREMENT_RESOLUTION 0.01 // mm + + #define CALIBRATION_FEEDRATE_SLOW 60 // mm/m + #define CALIBRATION_FEEDRATE_FAST 1200 // mm/m + #define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/m + + // The following parameters refer to the conical section of the nozzle tip. + #define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm + #define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm + + // Uncomment to enable reporting (required for "G425 V", but consumes PROGMEM). + //#define CALIBRATION_REPORTING + + // The true location and dimension the cube/bolt/washer on the bed. + #define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0} // mm + #define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0} // mm + + // Comment out any sides which are unreachable by the probe. For best + // auto-calibration results, all sides must be reachable. + #define CALIBRATION_MEASURE_RIGHT + #define CALIBRATION_MEASURE_FRONT + #define CALIBRATION_MEASURE_LEFT + #define CALIBRATION_MEASURE_BACK + + // Probing at the exact top center only works if the center is flat. If + // probing on a screwhead or hollow washer, probe near the edges. + //#define CALIBRATION_MEASURE_AT_TOP_EDGES + + // Define pin which is read during calibration + #ifndef CALIBRATION_PIN + #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop + #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin + //#define CALIBRATION_PIN_PULLDOWN + #define CALIBRATION_PIN_PULLUP + #endif +#endif + +/** + * Adaptive Step Smoothing increases the resolution of multi-axis moves, particularly at step frequencies + * below 1kHz (for AVR) or 10kHz (for ARM), where aliasing between axes in multi-axis moves causes audible + * vibration and surface artifacts. The algorithm adapts to provide the best possible step smoothing at the + * lowest stepping frequencies. + */ +//#define ADAPTIVE_STEP_SMOOTHING + +/** + * Custom Microstepping + * Override as-needed for your setup. Up to 3 MS pins are supported. + */ +//#define MICROSTEP1 LOW,LOW,LOW +//#define MICROSTEP2 HIGH,LOW,LOW +//#define MICROSTEP4 LOW,HIGH,LOW +//#define MICROSTEP8 HIGH,HIGH,LOW +//#define MICROSTEP16 LOW,LOW,HIGH +//#define MICROSTEP32 HIGH,LOW,HIGH + +// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU. +#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16] + +/** + * @section stepper motor current + * + * Some boards have a means of setting the stepper motor current via firmware. + * + * The power on motor currents are set by: + * PWM_MOTOR_CURRENT - used by MINIRAMBO & ULTIMAIN_2 + * known compatible chips: A4982 + * DIGIPOT_MOTOR_CURRENT - used by BQ_ZUM_MEGA_3D, RAMBO & SCOOVO_X9H + * known compatible chips: AD5206 + * DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2 + * known compatible chips: MCP4728 + * DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, AZTEEG_X5_MINI_WIFI, MIGHTYBOARD_REVE + * known compatible chips: MCP4451, MCP4018 + * + * Motor currents can also be set by M907 - M910 and by the LCD. + * M907 - applies to all. + * M908 - BQ_ZUM_MEGA_3D, RAMBO, PRINTRBOARD_REVF, RIGIDBOARD_V2 & SCOOVO_X9H + * M909, M910 & LCD - only PRINTRBOARD_REVF & RIGIDBOARD_V2 + */ +//#define PWM_MOTOR_CURRENT { 1300, 1300, 1250 } // Values in milliamps +//#define DIGIPOT_MOTOR_CURRENT { 135,135,135,135,135 } // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A) +//#define DAC_MOTOR_CURRENT_DEFAULT { 70, 80, 90, 80 } // Default drive percent - X, Y, Z, E axis + +// Use an I2C based DIGIPOT (e.g., Azteeg X3 Pro) +//#define DIGIPOT_I2C +#if ENABLED(DIGIPOT_I2C) && !defined(DIGIPOT_I2C_ADDRESS_A) + /** + * Common slave addresses: + * + * A (A shifted) B (B shifted) IC + * Smoothie 0x2C (0x58) 0x2D (0x5A) MCP4451 + * AZTEEG_X3_PRO 0x2C (0x58) 0x2E (0x5C) MCP4451 + * AZTEEG_X5_MINI 0x2C (0x58) 0x2E (0x5C) MCP4451 + * AZTEEG_X5_MINI_WIFI 0x58 0x5C MCP4451 + * MIGHTYBOARD_REVE 0x2F (0x5E) MCP4018 + */ + #define DIGIPOT_I2C_ADDRESS_A 0x2C // unshifted slave address for first DIGIPOT + #define DIGIPOT_I2C_ADDRESS_B 0x2D // unshifted slave address for second DIGIPOT +#endif + +//#define DIGIPOT_MCP4018 // Requires library from https://github.com/stawel/SlowSoftI2CMaster +#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8 MKS SBASE: 5 +// Actual motor currents in Amps. The number of entries must match DIGIPOT_I2C_NUM_CHANNELS. +// These correspond to the physical drivers, so be mindful if the order is changed. +#define DIGIPOT_I2C_MOTOR_CURRENTS { 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0 } // AZTEEG_X3_PRO + +//=========================================================================== +//=============================Additional Features=========================== +//=========================================================================== + +// @section lcd + +// Change values more rapidly when the encoder is rotated faster +#define ENCODER_RATE_MULTIPLIER +#if ENABLED(ENCODER_RATE_MULTIPLIER) + #define ENCODER_10X_STEPS_PER_SEC 30 // (steps/s) Encoder rate for 10x speed + #define ENCODER_100X_STEPS_PER_SEC 80 // (steps/s) Encoder rate for 100x speed +#endif + +// Play a beep when the feedrate is changed from the Status Screen +//#define BEEP_ON_FEEDRATE_CHANGE +#if ENABLED(BEEP_ON_FEEDRATE_CHANGE) + #define FEEDRATE_CHANGE_BEEP_DURATION 10 + #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 +#endif + +// Include a page of printer information in the LCD Main Menu +//#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif + +// Scroll a longer status message into view +//#define STATUS_MESSAGE_SCROLLING + +// On the Info Screen, display XY with one decimal place when possible +//#define LCD_DECIMAL_SMALL_XY + +// The timeout (in ms) to return to the status screen from sub-menus +//#define LCD_TIMEOUT_TO_STATUS 15000 + +// Add an 'M73' G-code to set the current percentage +//#define LCD_SET_PROGRESS_MANUALLY + +#if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS + //#define LCD_PROGRESS_BAR // Show a progress bar on HD44780 LCDs for SD printing + #if ENABLED(LCD_PROGRESS_BAR) + #define PROGRESS_BAR_BAR_TIME 2000 // (ms) Amount of time to show the bar + #define PROGRESS_BAR_MSG_TIME 3000 // (ms) Amount of time to show the status message + #define PROGRESS_MSG_EXPIRE 0 // (ms) Amount of time to retain the status message (0=forever) + //#define PROGRESS_MSG_ONCE // Show the message for MSG_TIME then clear it + //#define LCD_PROGRESS_BAR_TEST // Add a menu item to test the progress bar + #endif +#endif + +/** + * LED Control Menu + * Enable this feature to add LED Control to the LCD menu + */ +//#define LED_CONTROL_MENU +#if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + #define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif +#endif // LED_CONTROL_MENU + +#if ENABLED(SDSUPPORT) + + // Some RAMPS and other boards don't detect when an SD card is inserted. You can work + // around this by connecting a push button or single throw switch to the pin defined + // as SD_DETECT_PIN in your board's pins definitions. + // This setting should be disabled unless you are using a push button, pulling the pin to ground. + // Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER). + #define SD_DETECT_INVERTED + + #define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished + #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place. + + // Reverse SD sort to show "more recent" files first, according to the card's FAT. + // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended. + //#define SDCARD_RATHERRECENTFIRST + + #define SD_MENU_CONFIRM_START // Confirm the selected SD file before printing + + //#define MENU_ADDAUTOSTART // Add a menu option to run auto#.g files + + #define EVENT_GCODE_SD_STOP "M21" // G-code to run on Stop Print (e.g., "G28XY" or "G27") + + /** + * Continue after Power-Loss (Creality3D) + * + * Store the current state to the SD Card at the start of each layer + * during SD printing. If the recovery file is found at boot time, present + * an option on the LCD screen to continue the print from the last-known + * point in the file. + */ + //#define POWER_LOSS_RECOVERY + #if ENABLED(POWER_LOSS_RECOVERY) + //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume + //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. + + // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, + // especially with "vase mode" printing. Set too high and vases cannot be continued. + #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + #endif + + /** + * Sort SD file listings in alphabetical order. + * + * With this option enabled, items on SD cards will be sorted + * by name for easier navigation. + * + * By default... + * + * - Use the slowest -but safest- method for sorting. + * - Folders are sorted to the top. + * - The sort key is statically allocated. + * - No added G-code (M34) support. + * - 40 item sorting limit. (Items after the first 40 are unsorted.) + * + * SD sorting uses static allocation (as set by SDSORT_LIMIT), allowing the + * compiler to calculate the worst-case usage and throw an error if the SRAM + * limit is exceeded. + * + * - SDSORT_USES_RAM provides faster sorting via a static directory buffer. + * - SDSORT_USES_STACK does the same, but uses a local stack-based buffer. + * - SDSORT_CACHE_NAMES will retain the sorted file listing in RAM. (Expensive!) + * - SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible. (Use with caution!) + */ + //#define SDCARD_SORT_ALPHA + + // SD Card Sorting options + #if ENABLED(SDCARD_SORT_ALPHA) + #define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). Costs 27 bytes each. + #define FOLDER_SORTING -1 // -1=above 0=none 1=below + #define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 g-code. + #define SDSORT_USES_RAM true // Pre-allocate a static array for faster pre-sorting. + #define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.) + #define SDSORT_CACHE_NAMES true // Keep sorted items in RAM longer for speedy performance. Most expensive option. + #define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use! + #define SDSORT_CACHE_VFATS 2 // Maximum number of 13-byte VFAT entries to use for sorting. + // Note: Only affects SCROLL_LONG_FILENAMES with SDSORT_CACHE_NAMES but not SDSORT_DYNAMIC_RAM. + #endif + + // This allows hosts to request long names for files and folders with M33 + //#define LONG_FILENAME_HOST_SUPPORT + + // Enable this option to scroll long filenames in the SD card menu + //#define SCROLL_LONG_FILENAMES + + // Leave the heaters on after Stop Print (not recommended!) + //#define SD_ABORT_NO_COOLDOWN + + /** + * This option allows you to abort SD printing when any endstop is triggered. + * This feature must be enabled with "M540 S1" or from the LCD menu. + * To have any effect, endstops must be enabled during SD printing. + */ + //#define SD_ABORT_ON_ENDSTOP_HIT + + /** + * This option makes it easier to print the same SD Card file again. + * On print completion the LCD Menu will open with the file selected. + * You can just click to start the print, or navigate elsewhere. + */ + //#define SD_REPRINT_LAST_SELECTED_FILE + + /** + * Auto-report SdCard status with M27 S + */ + //#define AUTO_REPORT_SD_STATUS + + /** + * Support for USB thumb drives using an Arduino USB Host Shield or + * equivalent MAX3421E breakout board. The USB thumb drive will appear + * to Marlin as an SD card. + * + * The MAX3421E must be assigned the same pins as the SD card reader, with + * the following pin mapping: + * + * SCLK, MOSI, MISO --> SCLK, MOSI, MISO + * INT --> SD_DETECT_PIN + * SS --> SDSS + */ + //#define USB_FLASH_DRIVE_SUPPORT + #if ENABLED(USB_FLASH_DRIVE_SUPPORT) + #define USB_CS_PIN SDSS + #define USB_INTR_PIN SD_DETECT_PIN + #endif + + /** + * When using a bootloader that supports SD-Firmware-Flashing, + * add a menu item to activate SD-FW-Update on the next reboot. + * + * Requires ATMEGA2560 (Arduino Mega) + * + * Tested with this bootloader: + * https://github.com/FleetProbe/MicroBridge-Arduino-ATMega2560 + */ + //#define SD_FIRMWARE_UPDATE + #if ENABLED(SD_FIRMWARE_UPDATE) + #define SD_FIRMWARE_UPDATE_EEPROM_ADDR 0x1FF + #define SD_FIRMWARE_UPDATE_ACTIVE_VALUE 0xF0 + #define SD_FIRMWARE_UPDATE_INACTIVE_VALUE 0xFF + #endif + + // Add an optimized binary file transfer mode, initiated with 'M28 B1' + //#define BINARY_FILE_TRANSFER + + #if HAS_SDCARD_CONNECTION + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD + #endif + +#endif // SDSUPPORT + +/** + * By default an onboard SD card reader may be shared as a USB mass- + * storage device. This option hides the SD card from the host PC. + */ +//#define NO_SD_HOST_DRIVE // Disable SD Card access over USB (for security). + +/** + * Additional options for Graphical Displays + * + * Use the optimizations here to improve printing performance, + * which can be adversely affected by graphical display drawing, + * especially when doing several short moves, and when printing + * on DELTA and SCARA machines. + * + * Some of these options may result in the display lagging behind + * controller events, as there is a trade-off between reliable + * printing performance versus fast display updates. + */ +#if HAS_GRAPHICAL_LCD + // Show SD percentage next to the progress bar + //#define DOGM_SD_PERCENT + + // Enable to save many cycles by drawing a hollow frame on the Info Screen + #define XYZ_HOLLOW_FRAME + + // Enable to save many cycles by drawing a hollow frame on Menu Screens + #define MENU_HOLLOW_FRAME + + // A bigger font is available for edit items. Costs 3120 bytes of PROGMEM. + // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. + //#define USE_BIG_EDIT_FONT + + // A smaller font may be used on the Info Screen. Costs 2300 bytes of PROGMEM. + // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. + //#define USE_SMALL_INFOFONT + + // Enable this option and reduce the value to optimize screen updates. + // The normal delay is 10µs. Use the lowest value that still gives a reliable display. + //#define DOGM_SPI_DELAY_US 5 + + // Swap the CW/CCW indicators in the graphics overlay + //#define OVERLAY_GFX_REVERSE + + /** + * ST7920-based LCDs can emulate a 16 x 4 character display using + * the ST7920 character-generator for very fast screen updates. + * Enable LIGHTWEIGHT_UI to use this special display mode. + * + * Since LIGHTWEIGHT_UI has limited space, the position and status + * message occupy the same line. Set STATUS_EXPIRE_SECONDS to the + * length of time to display the status message before clearing. + * + * Set STATUS_EXPIRE_SECONDS to zero to never clear the status. + * This will prevent position updates from being displayed. + */ + #if ENABLED(U8GLIB_ST7920) + //#define LIGHTWEIGHT_UI + #if ENABLED(LIGHTWEIGHT_UI) + #define STATUS_EXPIRE_SECONDS 20 + #endif + #endif + + /** + * Status (Info) Screen customizations + * These options may affect code size and screen render time. + * Custom status screens can forcibly override these settings. + */ + //#define STATUS_COMBINE_HEATERS // Use combined heater images instead of separate ones + //#define STATUS_HOTEND_NUMBERLESS // Use plain hotend icons instead of numbered ones (with 2+ hotends) + #define STATUS_HOTEND_INVERTED // Show solid nozzle bitmaps when heating (Requires STATUS_HOTEND_ANIM) + #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating + #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating + #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap + //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap + //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames + //#define STATUS_HEAT_PERCENT // Show heating in a progress bar + //#define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash) + + // Frivolous Game Options + //#define MARLIN_BRICKOUT + //#define MARLIN_INVADERS + //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu + +#endif // HAS_GRAPHICAL_LCD + +// @section safety + +/** + * The watchdog hardware timer will do a reset and disable all outputs + * if the firmware gets too overloaded to read the temperature sensors. + * + * If you find that watchdog reboot causes your AVR board to hang forever, + * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO. + * NOTE: This method is less reliable as it can only catch hangups while + * interrupts are enabled. + */ +#define USE_WATCHDOG +#if ENABLED(USE_WATCHDOG) + //#define WATCHDOG_RESET_MANUAL +#endif + +// @section lcd + +/** + * Babystepping enables movement of the axes by tiny increments without changing + * the current position values. This feature is used primarily to adjust the Z + * axis in the first layer of a print in real-time. + * + * Warning: Does not respect endstops! + */ +//#define BABYSTEPPING +#if ENABLED(BABYSTEPPING) + //#define BABYSTEP_WITHOUT_HOMING + //#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA! + #define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way + #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion. + + //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping. + #if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING) + #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds. + // Note: Extra time may be added to mitigate controller latency. + //#define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement). + //#define MOVE_Z_WHEN_IDLE // Jump to the move Z menu on doubleclick when printer is idle. + #if ENABLED(MOVE_Z_WHEN_IDLE) + #define MOVE_Z_IDLE_MULTIPLICATOR 1 // Multiply 1mm by this factor for the move step size. + #endif + #endif + + //#define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28 + + //#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping + #if ENABLED(BABYSTEP_ZPROBE_OFFSET) + //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets + //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor + #endif +#endif + +// @section extruder + +/** + * Linear Pressure Control v1.5 + * + * Assumption: advance [steps] = k * (delta velocity [steps/s]) + * K=0 means advance disabled. + * + * NOTE: K values for LIN_ADVANCE 1.5 differ from earlier versions! + * + * Set K around 0.22 for 3mm PLA Direct Drive with ~6.5cm between the drive gear and heatbreak. + * Larger K values will be needed for flexible filament and greater distances. + * If this algorithm produces a higher speed offset than the extruder can handle (compared to E jerk) + * print acceleration will be reduced during the affected moves to keep within the limit. + * + * See http://marlinfw.org/docs/features/lin_advance.html for full instructions. + * Mention @Sebastianv650 on GitHub to alert the author of any issues. + */ +//#define LIN_ADVANCE +#if ENABLED(LIN_ADVANCE) + //#define EXTRA_LIN_ADVANCE_K // Enable for second linear advance constants + #define LIN_ADVANCE_K 0.22 // Unit: mm compression per 1mm/s extruder speed + //#define LA_DEBUG // If enabled, this will generate debug information output over USB. +#endif + +// @section leveling + +#if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL) + // Override the mesh area if the automatic (max) area is too large + //#define MESH_MIN_X MESH_INSET + //#define MESH_MIN_Y MESH_INSET + //#define MESH_MAX_X X_BED_SIZE - (MESH_INSET) + //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET) +#endif + +/** + * Repeatedly attempt G29 leveling until it succeeds. + * Stop after G29_MAX_RETRIES attempts. + */ +//#define G29_RETRY_AND_RECOVER +#if ENABLED(G29_RETRY_AND_RECOVER) + #define G29_MAX_RETRIES 3 + #define G29_HALT_ON_FAILURE + /** + * Specify the GCODE commands that will be executed when leveling succeeds, + * between attempts, and after the maximum number of retries have been tried. + */ + #define G29_SUCCESS_COMMANDS "M117 Bed leveling done." + #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0" + #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1" + +#endif + +// @section extras + +// +// G2/G3 Arc Support +// +#define ARC_SUPPORT // Disable this feature to save ~3226 bytes +#if ENABLED(ARC_SUPPORT) + #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles + //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes +#endif + +// Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes. +//#define BEZIER_CURVE_SUPPORT + +/** + * G38 Probe Target + * + * This option adds G38.2 and G38.3 (probe towards target) + * and optionally G38.4 and G38.5 (probe away from target). + * Set MULTIPLE_PROBING for G38 to probe more than once. + */ +//#define G38_PROBE_TARGET +#if ENABLED(G38_PROBE_TARGET) + //#define G38_PROBE_AWAY // Include G38.4 and G38.5 to probe away from target + #define G38_MINIMUM_MOVE 0.0275 // (mm) Minimum distance that will produce a move. +#endif + +// Moves (or segments) with fewer steps than this will be joined with the next move +#define MIN_STEPS_PER_SEGMENT 6 + +/** + * Minimum delay after setting the stepper DIR (in ns) + * 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire) + * 20 : Minimum for TMC2xxx drivers + * 200 : Minimum for A4988 drivers + * 400 : Minimum for A5984 drivers + * 500 : Minimum for LV8729 drivers (guess, no info in datasheet) + * 650 : Minimum for DRV8825 drivers + * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet) + * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet) + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MINIMUM_STEPPER_DIR_DELAY 650 + +/** + * Minimum stepper driver pulse width (in µs) + * 0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers + * 0 : Minimum 500ns for LV8729, adjusted in stepper.h + * 1 : Minimum for A4988 and A5984 stepper drivers + * 2 : Minimum for DRV8825 stepper drivers + * 3 : Minimum for TB6600 stepper drivers + * 30 : Minimum for TB6560 stepper drivers + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MINIMUM_STEPPER_PULSE 2 + +/** + * Maximum stepping rate (in Hz) the stepper driver allows + * If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE) + * 500000 : Maximum for A4988 stepper driver + * 400000 : Maximum for TMC2xxx stepper drivers + * 250000 : Maximum for DRV8825 stepper driver + * 200000 : Maximum for LV8729 stepper driver + * 150000 : Maximum for TB6600 stepper driver + * 15000 : Maximum for TB6560 stepper driver + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MAXIMUM_STEPPER_RATE 250000 + +// @section temperature + +// Control heater 0 and heater 1 in parallel. +//#define HEATERS_PARALLEL + +//=========================================================================== +//================================= Buffers ================================= +//=========================================================================== + +// @section hidden + +// The number of linear motions that can be in the plan at any give time. +// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2 (e.g. 8, 16, 32) because shifts and ors are used to do the ring-buffering. +#if ENABLED(SDSUPPORT) + #define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller +#else + #define BLOCK_BUFFER_SIZE 16 // maximize block buffer +#endif + +// @section serial + +// The ASCII buffer for serial input +#define MAX_CMD_SIZE 96 +#define BUFSIZE 4 + +// Transmission to Host Buffer Size +// To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0. +// To buffer a simple "ok" you need 4 bytes. +// For ADVANCED_OK (M105) you need 32 bytes. +// For debug-echo: 128 bytes for the optimal speed. +// Other output doesn't need to be that speedy. +// :[0, 2, 4, 8, 16, 32, 64, 128, 256] +#define TX_BUFFER_SIZE 0 + +// Host Receive Buffer Size +// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough. +// To use flow control, set this buffer size to at least 1024 bytes. +// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048] +//#define RX_BUFFER_SIZE 1024 + +#if RX_BUFFER_SIZE >= 1024 + // Enable to have the controller send XON/XOFF control characters to + // the host to signal the RX buffer is becoming full. + //#define SERIAL_XON_XOFF +#endif + +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + +#if ENABLED(SDSUPPORT) + // Enable this option to collect and display the maximum + // RX queue usage after transferring a file to SD. + //#define SERIAL_STATS_MAX_RX_QUEUED + + // Enable this option to collect and display the number + // of dropped bytes after a file transfer to SD. + //#define SERIAL_STATS_DROPPED_RX +#endif + +// Enable an emergency-command parser to intercept certain commands as they +// enter the serial receive buffer, so they cannot be blocked. +// Currently handles M108, M112, M410 +// Does not work on boards using AT90USB (USBCON) processors! +//#define EMERGENCY_PARSER + +// Bad Serial-connections can miss a received command by sending an 'ok' +// Therefore some clients abort after 30 seconds in a timeout. +// Some other clients start sending commands while receiving a 'wait'. +// This "wait" is only sent when the buffer is empty. 1 second is a good value here. +//#define NO_TIMEOUTS 1000 // Milliseconds + +// Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary. +//#define ADVANCED_OK + +// Printrun may have trouble receiving long strings all at once. +// This option inserts short delays between lines of serial output. +#define SERIAL_OVERRUN_PROTECTION + +// @section extras + +/** + * Extra Fan Speed + * Adds a secondary fan speed for each print-cooling fan. + * 'M106 P T3-255' : Set a secondary speed for + * 'M106 P T2' : Use the set secondary speed + * 'M106 P T1' : Restore the previous fan speed + */ +//#define EXTRA_FAN_SPEED + +/** + * Firmware-based and LCD-controlled retract + * + * Add G10 / G11 commands for automatic firmware-based retract / recover. + * Use M207 and M208 to define parameters for retract / recover. + * + * Use M209 to enable or disable auto-retract. + * With auto-retract enabled, all G1 E moves within the set range + * will be converted to firmware-based retract/recover moves. + * + * Be sure to turn off auto-retract during filament change. + * + * Note that M207 / M208 / M209 settings are saved to EEPROM. + * + */ +//#define FWRETRACT +#if ENABLED(FWRETRACT) + #define FWRETRACT_AUTORETRACT // costs ~500 bytes of PROGMEM + #if ENABLED(FWRETRACT_AUTORETRACT) + #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over + #define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion + #endif + #define RETRACT_LENGTH 3 // Default retract length (positive mm) + #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change + #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) + #define RETRACT_ZRAISE 0 // Default retract Z-raise (mm) + #define RETRACT_RECOVER_LENGTH 0 // Default additional recover length (mm, added to retract length when recovering) + #define RETRACT_RECOVER_LENGTH_SWAP 0 // Default additional swap recover length (mm, added to retract length when recovering from extruder change) + #define RETRACT_RECOVER_FEEDRATE 8 // Default feedrate for recovering from retraction (mm/s) + #define RETRACT_RECOVER_FEEDRATE_SWAP 8 // Default feedrate for recovering from swap retraction (mm/s) + #if ENABLED(MIXING_EXTRUDER) + //#define RETRACT_SYNC_MIXING // Retract and restore all mixing steppers simultaneously + #endif +#endif + +/** + * Universal tool change settings. + * Applies to all types of extruders except where explicitly noted. + */ +#if EXTRUDERS > 1 + // Z raise distance for tool-change, as needed for some extruders + #define TOOLCHANGE_ZRAISE 2 // (mm) + //#define TOOLCHANGE_NO_RETURN // Never return to the previous position on tool-change + + // Retract and prime filament on tool-change + //#define TOOLCHANGE_FILAMENT_SWAP + #if ENABLED(TOOLCHANGE_FILAMENT_SWAP) + #define TOOLCHANGE_FIL_SWAP_LENGTH 12 // (mm) + #define TOOLCHANGE_FIL_EXTRA_PRIME 2 // (mm) + #define TOOLCHANGE_FIL_SWAP_RETRACT_SPEED 3600 // (mm/m) + #define TOOLCHANGE_FIL_SWAP_PRIME_SPEED 3600 // (mm/m) + #endif + + /** + * Position to park head during tool change. + * Doesn't apply to SWITCHING_TOOLHEAD, DUAL_X_CARRIAGE, or PARKING_EXTRUDER + */ + //#define TOOLCHANGE_PARK + #if ENABLED(TOOLCHANGE_PARK) + #define TOOLCHANGE_PARK_XY { X_MIN_POS + 10, Y_MIN_POS + 10 } + #define TOOLCHANGE_PARK_XY_FEEDRATE 6000 // (mm/m) + #endif +#endif + +/** + * Advanced Pause + * Experimental feature for filament change support and for parking the nozzle when paused. + * Adds the GCode M600 for initiating filament change. + * If PARK_HEAD_ON_PAUSE enabled, adds the GCode M125 to pause printing and park the nozzle. + * + * Requires an LCD display. + * Requires NOZZLE_PARK_FEATURE. + * This feature is required for the default FILAMENT_RUNOUT_SCRIPT. + */ +//#define ADVANCED_PAUSE_FEATURE +#if ENABLED(ADVANCED_PAUSE_FEATURE) + #define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate. + #define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract. + // This short retract is done immediately, before parking the nozzle. + #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast. + #define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. + #define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload. + // For Bowden, the full length of the tube and nozzle. + // For direct drive, the full length of the nozzle. + // Set to 0 for manual unloading. + #define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load. + #define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material. + // 0 to disable start loading and skip to fast load only + #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast. + #define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. + #define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle. + // For Bowden, the full length of the tube and nozzle. + // For direct drive, the full length of the nozzle. + //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted. + #define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate. + #define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading. + // Set to 0 for manual extrusion. + // Filament can be extruded repeatedly from the Filament Change menu + // until extrusion is consistent, and to purge old filament. + #define ADVANCED_PAUSE_RESUME_PRIME 0 // (mm) Extra distance to prime nozzle after returning from park. + //#define ADVANCED_PAUSE_FANS_PAUSE // Turn off print-cooling fans while the machine is paused. + + // Filament Unload does a Retract, Delay, and Purge first: + #define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length. + #define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract. + #define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged. + + #define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety. + #define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed. + #define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change. + + //#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change. + //#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change + + //#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu. + //#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302) +#endif + +// @section tmc + +/** + * TMC26X Stepper Driver options + * + * The TMC26XStepper library is required for this stepper driver. + * https://github.com/trinamic/TMC26XStepper + */ +#if HAS_DRIVER(TMC26X) + + #if AXIS_DRIVER_TYPE_X(TMC26X) + #define X_MAX_CURRENT 1000 // (mA) + #define X_SENSE_RESISTOR 91 // (mOhms) + #define X_MICROSTEPS 16 // Number of microsteps + #endif + + #if AXIS_DRIVER_TYPE_X2(TMC26X) + #define X2_MAX_CURRENT 1000 + #define X2_SENSE_RESISTOR 91 + #define X2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Y(TMC26X) + #define Y_MAX_CURRENT 1000 + #define Y_SENSE_RESISTOR 91 + #define Y_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Y2(TMC26X) + #define Y2_MAX_CURRENT 1000 + #define Y2_SENSE_RESISTOR 91 + #define Y2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z(TMC26X) + #define Z_MAX_CURRENT 1000 + #define Z_SENSE_RESISTOR 91 + #define Z_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z2(TMC26X) + #define Z2_MAX_CURRENT 1000 + #define Z2_SENSE_RESISTOR 91 + #define Z2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z3(TMC26X) + #define Z3_MAX_CURRENT 1000 + #define Z3_SENSE_RESISTOR 91 + #define Z3_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E0(TMC26X) + #define E0_MAX_CURRENT 1000 + #define E0_SENSE_RESISTOR 91 + #define E0_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E1(TMC26X) + #define E1_MAX_CURRENT 1000 + #define E1_SENSE_RESISTOR 91 + #define E1_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E2(TMC26X) + #define E2_MAX_CURRENT 1000 + #define E2_SENSE_RESISTOR 91 + #define E2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E3(TMC26X) + #define E3_MAX_CURRENT 1000 + #define E3_SENSE_RESISTOR 91 + #define E3_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E4(TMC26X) + #define E4_MAX_CURRENT 1000 + #define E4_SENSE_RESISTOR 91 + #define E4_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E5(TMC26X) + #define E5_MAX_CURRENT 1000 + #define E5_SENSE_RESISTOR 91 + #define E5_MICROSTEPS 16 + #endif + +#endif // TMC26X + +// @section tmc_smart + +/** + * To use TMC2130, TMC2160, TMC2660, TMC5130, TMC5160 stepper drivers in SPI mode + * connect your SPI pins to the hardware SPI interface on your board and define + * the required CS pins in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 + * pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.). + * You may also use software SPI if you wish to use general purpose IO pins. + * + * To use TMC2208 stepper UART-configurable stepper drivers connect #_SERIAL_TX_PIN + * to the driver side PDN_UART pin with a 1K resistor. + * To use the reading capabilities, also connect #_SERIAL_RX_PIN to PDN_UART without + * a resistor. + * The drivers can also be used with hardware serial. + * + * TMCStepper library is required to use TMC stepper drivers. + * https://github.com/teemuatlut/TMCStepper + */ +#if HAS_TRINAMIC + + #define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current + #define INTERPOLATE true // Interpolate X/Y/Z_MICROSTEPS to 256 + + #if AXIS_IS_TMC(X) + #define X_CURRENT 700 // (mA) RMS current. Multiply by 1.414 for peak current. + #define X_MICROSTEPS 16 // 0..256 + #define X_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(X2) + #define X2_CURRENT 800 + #define X2_MICROSTEPS 16 + #define X2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Y) + #define Y_CURRENT 500 + #define Y_MICROSTEPS 16 + #define Y_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Y2) + #define Y2_CURRENT 800 + #define Y2_MICROSTEPS 16 + #define Y2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Z) + #define Z_CURRENT 800 + #define Z_MICROSTEPS 16 + #define Z_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Z2) + #define Z2_CURRENT 800 + #define Z2_MICROSTEPS 16 + #define Z2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Z3) + #define Z3_CURRENT 800 + #define Z3_MICROSTEPS 16 + #define Z3_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E0) + #define E0_CURRENT 650 + #define E0_MICROSTEPS 16 + #define E0_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E1) + #define E1_CURRENT 800 + #define E1_MICROSTEPS 16 + #define E1_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E2) + #define E2_CURRENT 800 + #define E2_MICROSTEPS 16 + #define E2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E3) + #define E3_CURRENT 800 + #define E3_MICROSTEPS 16 + #define E3_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E4) + #define E4_CURRENT 800 + #define E4_MICROSTEPS 16 + #define E4_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E5) + #define E5_CURRENT 800 + #define E5_MICROSTEPS 16 + #define E5_RSENSE 0.11 + #endif + + /** + * Override default SPI pins for TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160 drivers here. + * The default pins can be found in your board's pins file. + */ + //#define X_CS_PIN -1 + //#define Y_CS_PIN -1 + //#define Z_CS_PIN -1 + //#define X2_CS_PIN -1 + //#define Y2_CS_PIN -1 + //#define Z2_CS_PIN -1 + //#define Z3_CS_PIN -1 + //#define E0_CS_PIN -1 + //#define E1_CS_PIN -1 + //#define E2_CS_PIN -1 + //#define E3_CS_PIN -1 + //#define E4_CS_PIN -1 + //#define E5_CS_PIN -1 + + /** + * Software option for SPI driven drivers (TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160). + * The default SW SPI pins are defined the respective pins files, + * but you can override or define them here. + */ + //#define TMC_USE_SW_SPI + //#define TMC_SW_MOSI -1 + //#define TMC_SW_MISO -1 + //#define TMC_SW_SCK -1 + + /** + * Four TMC2209 drivers can use the same HW/SW serial port with hardware configured addresses. + * Set the address using jumpers on pins MS1 and MS2. + * Address | MS1 | MS2 + * 0 | LOW | LOW + * 1 | HIGH | LOW + * 2 | LOW | HIGH + * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. + */ + #define X_SLAVE_ADDRESS 0 + #define Y_SLAVE_ADDRESS 1 + #define Z_SLAVE_ADDRESS 2 + #define X2_SLAVE_ADDRESS 0 + #define Y2_SLAVE_ADDRESS 0 + #define Z2_SLAVE_ADDRESS 0 + #define Z3_SLAVE_ADDRESS 0 + #define E0_SLAVE_ADDRESS 3 + #define E1_SLAVE_ADDRESS 0 + #define E2_SLAVE_ADDRESS 0 + #define E3_SLAVE_ADDRESS 0 + #define E4_SLAVE_ADDRESS 0 + #define E5_SLAVE_ADDRESS 0 + + /** + * Software enable + * + * Use for drivers that do not use a dedicated enable pin, but rather handle the same + * function through a communication line such as SPI or UART. + */ + //#define SOFTWARE_DRIVER_ENABLE + + /** + * TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only + * Use Trinamic's ultra quiet stepping mode. + * When disabled, Marlin will use spreadCycle stepping mode. + */ + #define STEALTHCHOP_XY + #define STEALTHCHOP_Z + #define STEALTHCHOP_E + + /** + * Optimize spreadCycle chopper parameters by using predefined parameter sets + * or with the help of an example included in the library. + * Provided parameter sets are + * CHOPPER_DEFAULT_12V + * CHOPPER_DEFAULT_19V + * CHOPPER_DEFAULT_24V + * CHOPPER_DEFAULT_36V + * CHOPPER_PRUSAMK3_24V // Imported parameters from the official Prusa firmware for MK3 (24V) + * CHOPPER_MARLIN_119 // Old defaults from Marlin v1.1.9 + * + * Define you own with + * { , , hysteresis_start[1..8] } + */ + #define CHOPPER_TIMING CHOPPER_DEFAULT_12V + + /** + * Monitor Trinamic drivers for error conditions, + * like overtemperature and short to ground. + * In the case of overtemperature Marlin can decrease the driver current until error condition clears. + * Other detected conditions can be used to stop the current print. + * Relevant g-codes: + * M906 - Set or get motor current in milliamps using axis codes X, Y, Z, E. Report values if no axis codes given. + * M911 - Report stepper driver overtemperature pre-warn condition. + * M912 - Clear stepper driver overtemperature pre-warn condition flag. + * M122 - Report driver parameters (Requires TMC_DEBUG) + */ + #define MONITOR_DRIVER_STATUS + + #if ENABLED(MONITOR_DRIVER_STATUS) + #define CURRENT_STEP_DOWN 50 // [mA] + #define REPORT_CURRENT_CHANGE + #define STOP_ON_ERROR + #endif + + /** + * TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only + * The driver will switch to spreadCycle when stepper speed is over HYBRID_THRESHOLD. + * This mode allows for faster movements at the expense of higher noise levels. + * STEALTHCHOP_(XY|Z|E) must be enabled to use HYBRID_THRESHOLD. + * M913 X/Y/Z/E to live tune the setting + */ + //#define HYBRID_THRESHOLD + + #define X_HYBRID_THRESHOLD 100 // [mm/s] + #define X2_HYBRID_THRESHOLD 100 + #define Y_HYBRID_THRESHOLD 100 + #define Y2_HYBRID_THRESHOLD 100 + #define Z_HYBRID_THRESHOLD 3 + #define Z2_HYBRID_THRESHOLD 3 + #define Z3_HYBRID_THRESHOLD 3 + #define E0_HYBRID_THRESHOLD 30 + #define E1_HYBRID_THRESHOLD 30 + #define E2_HYBRID_THRESHOLD 30 + #define E3_HYBRID_THRESHOLD 30 + #define E4_HYBRID_THRESHOLD 30 + #define E5_HYBRID_THRESHOLD 30 + + /** + * TMC2130, TMC2160, TMC2209, TMC2660, TMC5130, and TMC5160 only + * Use StallGuard2 to sense an obstacle and trigger an endstop. + * Connect the stepper driver's DIAG1 pin to the X/Y endstop pin. + * X, Y, and Z homing will always be done in spreadCycle mode. + * + * X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity. + * Higher values make the system LESS sensitive. + * Lower value make the system MORE sensitive. + * Too low values can lead to false positives, while too high values will collide the axis without triggering. + * It is advised to set X/Y/Z_HOME_BUMP_MM to 0. + * M914 X/Y/Z to live tune the setting + */ + //#define SENSORLESS_HOMING // StallGuard capable drivers only + + /** + * Use StallGuard2 to probe the bed with the nozzle. + * + * CAUTION: This could cause damage to machines that use a lead screw or threaded rod + * to move the Z axis. Take extreme care when attempting to enable this feature. + */ + //#define SENSORLESS_PROBING // StallGuard capable drivers only + + #if EITHER(SENSORLESS_HOMING, SENSORLESS_PROBING) + // TMC2209: 0...255. TMC2130: -64...63 + #define X_STALL_SENSITIVITY 8 + #define Y_STALL_SENSITIVITY 8 + //#define Z_STALL_SENSITIVITY 8 + #endif + + /** + * Beta feature! + * Create a 50/50 square wave step pulse optimal for stepper drivers. + */ + //#define SQUARE_WAVE_STEPPING + + /** + * Enable M122 debugging command for TMC stepper drivers. + * M122 S0/1 will enable continous reporting. + */ + //#define TMC_DEBUG + + /** + * You can set your own advanced settings by filling in predefined functions. + * A list of available functions can be found on the library github page + * https://github.com/teemuatlut/TMCStepper + * + * Example: + * #define TMC_ADV() { \ + * stepperX.diag0_temp_prewarn(1); \ + * stepperY.interpolate(0); \ + * } + */ + #define TMC_ADV() { } + +#endif // HAS_TRINAMIC + +// @section L6470 + +/** + * L6470 Stepper Driver options + * + * Arduino-L6470 library (0.7.0 or higher) is required for this stepper driver. + * https://github.com/ameyer/Arduino-L6470 + * + * Requires the following to be defined in your pins_YOUR_BOARD file + * L6470_CHAIN_SCK_PIN + * L6470_CHAIN_MISO_PIN + * L6470_CHAIN_MOSI_PIN + * L6470_CHAIN_SS_PIN + * L6470_RESET_CHAIN_PIN (optional) + */ +#if HAS_DRIVER(L6470) + + //#define L6470_CHITCHAT // Display additional status info + + #if AXIS_DRIVER_TYPE_X(L6470) + #define X_MICROSTEPS 128 // Number of microsteps (VALID: 1, 2, 4, 8, 16, 32, 128) + #define X_OVERCURRENT 2000 // (mA) Current where the driver detects an over current (VALID: 375 x (1 - 16) - 6A max - rounds down) + #define X_STALLCURRENT 1500 // (mA) Current where the driver detects a stall (VALID: 31.25 * (1-128) - 4A max - rounds down) + #define X_MAX_VOLTAGE 127 // 0-255, Maximum effective voltage seen by stepper + #define X_CHAIN_POS 0 // Position in SPI chain, 0=Not in chain, 1=Nearest MOSI + #endif + + #if AXIS_DRIVER_TYPE_X2(L6470) + #define X2_MICROSTEPS 128 + #define X2_OVERCURRENT 2000 + #define X2_STALLCURRENT 1500 + #define X2_MAX_VOLTAGE 127 + #define X2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Y(L6470) + #define Y_MICROSTEPS 128 + #define Y_OVERCURRENT 2000 + #define Y_STALLCURRENT 1500 + #define Y_MAX_VOLTAGE 127 + #define Y_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Y2(L6470) + #define Y2_MICROSTEPS 128 + #define Y2_OVERCURRENT 2000 + #define Y2_STALLCURRENT 1500 + #define Y2_MAX_VOLTAGE 127 + #define Y2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Z(L6470) + #define Z_MICROSTEPS 128 + #define Z_OVERCURRENT 2000 + #define Z_STALLCURRENT 1500 + #define Z_MAX_VOLTAGE 127 + #define Z_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Z2(L6470) + #define Z2_MICROSTEPS 128 + #define Z2_OVERCURRENT 2000 + #define Z2_STALLCURRENT 1500 + #define Z2_MAX_VOLTAGE 127 + #define Z2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Z3(L6470) + #define Z3_MICROSTEPS 128 + #define Z3_OVERCURRENT 2000 + #define Z3_STALLCURRENT 1500 + #define Z3_MAX_VOLTAGE 127 + #define Z3_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E0(L6470) + #define E0_MICROSTEPS 128 + #define E0_OVERCURRENT 2000 + #define E0_STALLCURRENT 1500 + #define E0_MAX_VOLTAGE 127 + #define E0_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E1(L6470) + #define E1_MICROSTEPS 128 + #define E1_OVERCURRENT 2000 + #define E1_STALLCURRENT 1500 + #define E1_MAX_VOLTAGE 127 + #define E1_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E2(L6470) + #define E2_MICROSTEPS 128 + #define E2_OVERCURRENT 2000 + #define E2_STALLCURRENT 1500 + #define E2_MAX_VOLTAGE 127 + #define E2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E3(L6470) + #define E3_MICROSTEPS 128 + #define E3_OVERCURRENT 2000 + #define E3_STALLCURRENT 1500 + #define E3_MAX_VOLTAGE 127 + #define E3_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E4(L6470) + #define E4_MICROSTEPS 128 + #define E4_OVERCURRENT 2000 + #define E4_STALLCURRENT 1500 + #define E4_MAX_VOLTAGE 127 + #define E4_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E5(L6470) + #define E5_MICROSTEPS 128 + #define E5_OVERCURRENT 2000 + #define E5_STALLCURRENT 1500 + #define E5_MAX_VOLTAGE 127 + #define E5_CHAIN_POS 0 + #endif + + /** + * Monitor L6470 drivers for error conditions like over temperature and over current. + * In the case of over temperature Marlin can decrease the drive until the error condition clears. + * Other detected conditions can be used to stop the current print. + * Relevant g-codes: + * M906 - I1/2/3/4/5 Set or get motor drive level using axis codes X, Y, Z, E. Report values if no axis codes given. + * I not present or I0 or I1 - X, Y, Z or E0 + * I2 - X2, Y2, Z2 or E1 + * I3 - Z3 or E3 + * I4 - E4 + * I5 - E5 + * M916 - Increase drive level until get thermal warning + * M917 - Find minimum current thresholds + * M918 - Increase speed until max or error + * M122 S0/1 - Report driver parameters + */ + //#define MONITOR_L6470_DRIVER_STATUS + + #if ENABLED(MONITOR_L6470_DRIVER_STATUS) + #define KVAL_HOLD_STEP_DOWN 1 + //#define L6470_STOP_ON_ERROR + #endif + +#endif // L6470 + +/** + * TWI/I2C BUS + * + * This feature is an EXPERIMENTAL feature so it shall not be used on production + * machines. Enabling this will allow you to send and receive I2C data from slave + * devices on the bus. + * + * ; Example #1 + * ; This macro send the string "Marlin" to the slave device with address 0x63 (99) + * ; It uses multiple M260 commands with one B arg + * M260 A99 ; Target slave address + * M260 B77 ; M + * M260 B97 ; a + * M260 B114 ; r + * M260 B108 ; l + * M260 B105 ; i + * M260 B110 ; n + * M260 S1 ; Send the current buffer + * + * ; Example #2 + * ; Request 6 bytes from slave device with address 0x63 (99) + * M261 A99 B5 + * + * ; Example #3 + * ; Example serial output of a M261 request + * echo:i2c-reply: from:99 bytes:5 data:hello + */ + +// @section i2cbus + +//#define EXPERIMENTAL_I2CBUS +#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave + +// @section extras + +/** + * Photo G-code + * Add the M240 G-code to take a photo. + * The photo can be triggered by a digital pin or a physical movement. + */ +//#define PHOTO_GCODE +#if ENABLED(PHOTO_GCODE) + // A position to move to (and raise Z) before taking the photo + //#define PHOTO_POSITION { X_MAX_POS - 5, Y_MAX_POS, 0 } // { xpos, ypos, zraise } (M240 X Y Z) + //#define PHOTO_DELAY_MS 100 // (ms) Duration to pause before moving back (M240 P) + //#define PHOTO_RETRACT_MM 6.5 // (mm) E retract/recover for the photo move (M240 R S) + + // Canon RC-1 or homebrew digital camera trigger + // Data from: http://www.doc-diy.net/photo/rc-1_hacked/ + //#define PHOTOGRAPH_PIN 23 + + // Canon Hack Development Kit + // http://captain-slow.dk/2014/03/09/3d-printing-timelapses/ + //#define CHDK_PIN 4 + + // Optional second move with delay to trigger the camera shutter + //#define PHOTO_SWITCH_POSITION { X_MAX_POS, Y_MAX_POS } // { xpos, ypos } (M240 I J) + + // Duration to hold the switch or keep CHDK_PIN high + //#define PHOTO_SWITCH_MS 50 // (ms) (M240 D) +#endif + +/** + * Spindle & Laser control + * + * Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and + * to set spindle speed, spindle direction, and laser power. + * + * SuperPid is a router/spindle speed controller used in the CNC milling community. + * Marlin can be used to turn the spindle on and off. It can also be used to set + * the spindle speed from 5,000 to 30,000 RPM. + * + * You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V + * hardware PWM pin for the speed control and a pin for the rotation direction. + * + * See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details. + */ +//#define SPINDLE_FEATURE +//#define LASER_FEATURE +#if EITHER(SPINDLE_FEATURE, LASER_FEATURE) + #define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH + #define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power + #define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower + #define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power + #define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop + + #if ENABLED(SPINDLE_FEATURE) + //#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction + #define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction + #define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed + + /** + * The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power + * + * SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT + * where PWM duty cycle varies from 0 to 255 + * + * set the following for your controller (ALL MUST BE SET) + */ + #define SPEED_POWER_SLOPE 118.4 + #define SPEED_POWER_INTERCEPT 0 + #define SPEED_POWER_MIN 5000 + #define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM + #else + #define SPEED_POWER_SLOPE 0.3922 + #define SPEED_POWER_INTERCEPT 0 + #define SPEED_POWER_MIN 10 + #define SPEED_POWER_MAX 100 // 0-100% + #endif +#endif + +/** + * Coolant Control + * + * Add the M7, M8, and M9 commands to turn mist or flood coolant on and off. + * + * Note: COOLANT_MIST_PIN and/or COOLANT_FLOOD_PIN must also be defined. + */ +//#define COOLANT_CONTROL +#if ENABLED(COOLANT_CONTROL) + #define COOLANT_MIST // Enable if mist coolant is present + #define COOLANT_FLOOD // Enable if flood coolant is present + #define COOLANT_MIST_INVERT false // Set "true" if the on/off function is reversed + #define COOLANT_FLOOD_INVERT false // Set "true" if the on/off function is reversed +#endif + +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define FILWIDTH_ERROR_MARGIN 1.0 // (mm) If a measurement differs too much from nominal width ignore it + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + +/** + * CNC Coordinate Systems + * + * Enables G53 and G54-G59.3 commands to select coordinate systems + * and G92.1 to reset the workspace to native machine space. + */ +//#define CNC_COORDINATE_SYSTEMS + +/** + * Auto-report temperatures with M155 S + */ +#define AUTO_REPORT_TEMPERATURES + +/** + * Include capabilities in M115 output + */ +#define EXTENDED_CAPABILITIES_REPORT + +/** + * Disable all Volumetric extrusion options + */ +//#define NO_VOLUMETRICS + +#if DISABLED(NO_VOLUMETRICS) + /** + * Volumetric extrusion default state + * Activate to make volumetric extrusion the default method, + * with DEFAULT_NOMINAL_FILAMENT_DIA as the default diameter. + * + * M200 D0 to disable, M200 Dn to set a new diameter. + */ + //#define VOLUMETRIC_DEFAULT_ON +#endif + +/** + * Enable this option for a leaner build of Marlin that removes all + * workspace offsets, simplifying coordinate transformations, leveling, etc. + * + * - M206 and M428 are disabled. + * - G92 will revert to its behavior from Marlin 1.0. + */ +//#define NO_WORKSPACE_OFFSETS + +/** + * Set the number of proportional font spaces required to fill up a typical character space. + * This can help to better align the output of commands like `G29 O` Mesh Output. + * + * For clients that use a fixed-width font (like OctoPrint), leave this set to 1.0. + * Otherwise, adjust according to your client and font. + */ +#define PROPORTIONAL_FONT_RATIO 1.0 + +/** + * Spend 28 bytes of SRAM to optimize the GCode parser + */ +#define FASTER_GCODE_PARSER + +/** + * CNC G-code options + * Support CNC-style G-code dialects used by laser cutters, drawing machine cams, etc. + * Note that G0 feedrates should be used with care for 3D printing (if used at all). + * High feedrates may cause ringing and harm print quality. + */ +//#define PAREN_COMMENTS // Support for parentheses-delimited comments +//#define GCODE_MOTION_MODES // Remember the motion mode (G0 G1 G2 G3 G5 G38.X) and apply for X Y Z E F, etc. + +// Enable and set a (default) feedrate for all G0 moves +//#define G0_FEEDRATE 3000 // (mm/m) +#ifdef G0_FEEDRATE + //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode +#endif + +/** + * G-code Macros + * + * Add G-codes M810-M819 to define and run G-code macros. + * Macros are not saved to EEPROM. + */ +//#define GCODE_MACROS +#if ENABLED(GCODE_MACROS) + #define GCODE_MACROS_SLOTS 5 // Up to 10 may be used + #define GCODE_MACROS_SLOT_SIZE 50 // Maximum length of a single macro +#endif + +/** + * User-defined menu items that execute custom GCode + */ +//#define CUSTOM_USER_MENUS +#if ENABLED(CUSTOM_USER_MENUS) + //#define CUSTOM_USER_MENU_TITLE "Custom Commands" + #define USER_SCRIPT_DONE "M117 User Script Done" + #define USER_SCRIPT_AUDIBLE_FEEDBACK + //#define USER_SCRIPT_RETURN // Return to status screen after a script + + #define USER_DESC_1 "Home & UBL Info" + #define USER_GCODE_1 "G28\nG29 W" + + #define USER_DESC_2 "Preheat for " PREHEAT_1_LABEL + #define USER_GCODE_2 "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND) + + #define USER_DESC_3 "Preheat for " PREHEAT_2_LABEL + #define USER_GCODE_3 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND) + + #define USER_DESC_4 "Heat Bed/Home/Level" + #define USER_GCODE_4 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29" + + #define USER_DESC_5 "Home & Info" + #define USER_GCODE_5 "G28\nM503" +#endif + +/** + * Host Action Commands + * + * Define host streamer action commands in compliance with the standard. + * + * See https://reprap.org/wiki/G-code#Action_commands + * Common commands ........ poweroff, pause, paused, resume, resumed, cancel + * G29_RETRY_AND_RECOVER .. probe_rewipe, probe_failed + * + * Some features add reason codes to extend these commands. + * + * Host Prompt Support enables Marlin to use the host for user prompts so + * filament runout and other processes can be managed from the host side. + */ +//#define HOST_ACTION_COMMANDS +#if ENABLED(HOST_ACTION_COMMANDS) + //#define HOST_PROMPT_SUPPORT +#endif + +//=========================================================================== +//====================== I2C Position Encoder Settings ====================== +//=========================================================================== + +/** + * I2C position encoders for closed loop control. + * Developed by Chris Barr at Aus3D. + * + * Wiki: http://wiki.aus3d.com.au/Magnetic_Encoder + * Github: https://github.com/Aus3D/MagneticEncoder + * + * Supplier: http://aus3d.com.au/magnetic-encoder-module + * Alternative Supplier: http://reliabuild3d.com/ + * + * Reliabuild encoders have been modified to improve reliability. + */ + +//#define I2C_POSITION_ENCODERS +#if ENABLED(I2C_POSITION_ENCODERS) + + #define I2CPE_ENCODER_CNT 1 // The number of encoders installed; max of 5 + // encoders supported currently. + + #define I2CPE_ENC_1_ADDR I2CPE_PRESET_ADDR_X // I2C address of the encoder. 30-200. + #define I2CPE_ENC_1_AXIS X_AXIS // Axis the encoder module is installed on. _AXIS. + #define I2CPE_ENC_1_TYPE I2CPE_ENC_TYPE_LINEAR // Type of encoder: I2CPE_ENC_TYPE_LINEAR -or- + // I2CPE_ENC_TYPE_ROTARY. + #define I2CPE_ENC_1_TICKS_UNIT 2048 // 1024 for magnetic strips with 2mm poles; 2048 for + // 1mm poles. For linear encoders this is ticks / mm, + // for rotary encoders this is ticks / revolution. + //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper + // steps per full revolution (motor steps/rev * microstepping) + //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the + // printer will attempt to correct the error; errors + // smaller than this are ignored to minimize effects of + // measurement noise / latency (filter). + + #define I2CPE_ENC_2_ADDR I2CPE_PRESET_ADDR_Y // Same as above, but for encoder 2. + #define I2CPE_ENC_2_AXIS Y_AXIS + #define I2CPE_ENC_2_TYPE I2CPE_ENC_TYPE_LINEAR + #define I2CPE_ENC_2_TICKS_UNIT 2048 + //#define I2CPE_ENC_2_TICKS_REV (16 * 200) + //#define I2CPE_ENC_2_INVERT + #define I2CPE_ENC_2_EC_METHOD I2CPE_ECM_MICROSTEP + #define I2CPE_ENC_2_EC_THRESH 0.10 + + #define I2CPE_ENC_3_ADDR I2CPE_PRESET_ADDR_Z // Encoder 3. Add additional configuration options + #define I2CPE_ENC_3_AXIS Z_AXIS // as above, or use defaults below. + + #define I2CPE_ENC_4_ADDR I2CPE_PRESET_ADDR_E // Encoder 4. + #define I2CPE_ENC_4_AXIS E_AXIS + + #define I2CPE_ENC_5_ADDR 34 // Encoder 5. + #define I2CPE_ENC_5_AXIS E_AXIS + + // Default settings for encoders which are enabled, but without settings configured above. + #define I2CPE_DEF_TYPE I2CPE_ENC_TYPE_LINEAR + #define I2CPE_DEF_ENC_TICKS_UNIT 2048 + #define I2CPE_DEF_TICKS_REV (16 * 200) + #define I2CPE_DEF_EC_METHOD I2CPE_ECM_NONE + #define I2CPE_DEF_EC_THRESH 0.1 + + //#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given + // axis after which the printer will abort. Comment out to + // disable abort behavior. + + #define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault + // for this amount of time (in ms) before the encoder + // is trusted again. + + /** + * Position is checked every time a new command is executed from the buffer but during long moves, + * this setting determines the minimum update time between checks. A value of 100 works well with + * error rolling average when attempting to correct only for skips and not for vibration. + */ + #define I2CPE_MIN_UPD_TIME_MS 4 // (ms) Minimum time between encoder checks. + + // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise. + #define I2CPE_ERR_ROLLING_AVERAGE + +#endif // I2C_POSITION_ENCODERS + +/** + * MAX7219 Debug Matrix + * + * Add support for a low-cost 8x8 LED Matrix based on the Max7219 chip as a realtime status display. + * Requires 3 signal wires. Some useful debug options are included to demonstrate its usage. + */ +//#define MAX7219_DEBUG +#if ENABLED(MAX7219_DEBUG) + #define MAX7219_CLK_PIN 64 + #define MAX7219_DIN_PIN 57 + #define MAX7219_LOAD_PIN 44 + + //#define MAX7219_GCODE // Add the M7219 G-code to control the LED matrix + #define MAX7219_INIT_TEST 2 // Do a test pattern at initialization (Set to 2 for spiral) + #define MAX7219_NUMBER_UNITS 1 // Number of Max7219 units in chain. + #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) + // connector at: right=0 bottom=-90 top=90 left=180 + //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side + + /** + * Sample debug features + * If you add more debug displays, be careful to avoid conflicts! + */ + #define MAX7219_DEBUG_PRINTER_ALIVE // Blink corner LED of 8x8 matrix to show that the firmware is functioning + #define MAX7219_DEBUG_PLANNER_HEAD 3 // Show the planner queue head position on this and the next LED matrix row + #define MAX7219_DEBUG_PLANNER_TAIL 5 // Show the planner queue tail position on this and the next LED matrix row + + #define MAX7219_DEBUG_PLANNER_QUEUE 0 // Show the current planner queue depth on this and the next LED matrix row + // If you experience stuttering, reboots, etc. this option can reveal how + // tweaks made to the configuration are affecting the printer in real-time. +#endif + +/** + * NanoDLP Sync support + * + * Add support for Synchronized Z moves when using with NanoDLP. G0/G1 axis moves will output "Z_move_comp" + * string to enable synchronization with DLP projector exposure. This change will allow to use + * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands + */ +//#define NANODLP_Z_SYNC +#if ENABLED(NANODLP_Z_SYNC) + //#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move. + // Default behavior is limited to Z axis only. +#endif + +/** + * WiFi Support (Espressif ESP32 WiFi) + */ +//#define WIFISUPPORT +#if ENABLED(WIFISUPPORT) + #define WIFI_SSID "Wifi SSID" + #define WIFI_PWD "Wifi Password" + //#define WEBSUPPORT // Start a webserver with auto-discovery + //#define OTASUPPORT // Support over-the-air firmware updates +#endif + +/** + * Prusa Multi-Material Unit v2 + * Enable in Configuration.h + */ +#if ENABLED(PRUSA_MMU2) + + // Serial port used for communication with MMU2. + // For AVR enable the UART port used for the MMU. (e.g., internalSerial) + // For 32-bit boards check your HAL for available serial ports. (e.g., Serial2) + #define INTERNAL_SERIAL_PORT 2 + #define MMU2_SERIAL internalSerial + + // Use hardware reset for MMU if a pin is defined for it + //#define MMU2_RST_PIN 23 + + // Enable if the MMU2 has 12V stepper motors (MMU2 Firmware 1.0.2 and up) + //#define MMU2_MODE_12V + + // G-code to execute when MMU2 F.I.N.D.A. probe detects filament runout + #define MMU2_FILAMENT_RUNOUT_SCRIPT "M600" + + // Add an LCD menu for MMU2 + //#define MMU2_MENUS + #if ENABLED(MMU2_MENUS) + // Settings for filament load / unload from the LCD menu. + // This is for Prusa MK3-style extruders. Customize for your hardware. + #define MMU2_FILAMENTCHANGE_EJECT_FEED 80.0 + #define MMU2_LOAD_TO_NOZZLE_SEQUENCE \ + { 7.2, 562 }, \ + { 14.4, 871 }, \ + { 36.0, 1393 }, \ + { 14.4, 871 }, \ + { 50.0, 198 } + + #define MMU2_RAMMING_SEQUENCE \ + { 1.0, 1000 }, \ + { 1.0, 1500 }, \ + { 2.0, 2000 }, \ + { 1.5, 3000 }, \ + { 2.5, 4000 }, \ + { -15.0, 5000 }, \ + { -14.0, 1200 }, \ + { -6.0, 600 }, \ + { 10.0, 700 }, \ + { -10.0, 400 }, \ + { -50.0, 2000 } + + #endif + + //#define MMU2_DEBUG // Write debug info to serial output + +#endif // PRUSA_MMU2 + +/** + * Advanced Print Counter settings + */ +#if ENABLED(PRINTCOUNTER) + #define SERVICE_WARNING_BUZZES 3 + // Activate up to 3 service interval watchdogs + //#define SERVICE_NAME_1 "Service S" + //#define SERVICE_INTERVAL_1 100 // print hours + //#define SERVICE_NAME_2 "Service L" + //#define SERVICE_INTERVAL_2 200 // print hours + //#define SERVICE_NAME_3 "Service 3" + //#define SERVICE_INTERVAL_3 1 // print hours +#endif + +// @section develop + +/** + * M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins + */ +//#define PINS_DEBUGGING + +// Enable Marlin dev mode which adds some special commands +//#define MARLIN_DEV_MODE diff --git a/config/examples/FYSETC/Cheetah/base/Configuration.h b/config/examples/FYSETC/Cheetah/base/Configuration.h new file mode 100644 index 0000000000..dad8ce5525 --- /dev/null +++ b/config/examples/FYSETC/Cheetah/base/Configuration.h @@ -0,0 +1,2221 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Configuration.h + * + * Basic settings such as: + * + * - Type of electronics + * - Type of temperature sensor + * - Printer geometry + * - Endstop configuration + * - LCD controller + * - Extra features + * + * Advanced settings can be found in Configuration_adv.h + * + */ +#define CONFIGURATION_H_VERSION 020000 + +//=========================================================================== +//============================= Getting Started ============================= +//=========================================================================== + +/** + * Here are some standard links for getting your machine calibrated: + * + * http://reprap.org/wiki/Calibration + * http://youtu.be/wAL9d7FgInk + * http://calculator.josefprusa.cz + * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide + * http://www.thingiverse.com/thing:5573 + * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap + * http://www.thingiverse.com/thing:298812 + */ + +//=========================================================================== +//============================= DELTA Printer =============================== +//=========================================================================== +// For a Delta printer start with one of the configuration files in the +// config/examples/delta directory and customize for your machine. +// + +//=========================================================================== +//============================= SCARA Printer =============================== +//=========================================================================== +// For a SCARA printer start with the configuration files in +// config/examples/SCARA and customize for your machine. +// + +// @section info + +// User-specified version info of this build to display in [Pronterface, etc] terminal window during +// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this +// build by the user have been successfully uploaded into firmware. +#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes. +#define SHOW_BOOTSCREEN +#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1 +#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2 + +/** + * *** VENDORS PLEASE READ *** + * + * Marlin allows you to add a custom boot image for Graphical LCDs. + * With this option Marlin will first show your custom screen followed + * by the standard Marlin logo with version number and web URL. + * + * We encourage you to take advantage of this new feature and we also + * respectfully request that you retain the unmodified Marlin boot screen. + */ + +// Enable to show the bitmap in Marlin/_Bootscreen.h on startup. +//#define SHOW_CUSTOM_BOOTSCREEN + +// Enable to show the bitmap in Marlin/_Statusscreen.h on the status screen. +//#define CUSTOM_STATUS_SCREEN_IMAGE + +// @section machine + +/** + * Select the serial port on the board to use for communication with the host. + * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. + * + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] + */ +#define SERIAL_PORT 1 // libmaple 0 for USB ,1 for serial + +/** + * Select a secondary serial port on the board to use for communication with the host. + * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. + * + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] + */ +//#define SERIAL_PORT_2 -1 + +/** + * This setting determines the communication speed of the printer. + * + * 250000 works in most cases, but you might try a lower speed if + * you commonly experience drop-outs during host printing. + * You may try up to 1000000 to speed up SD file transfer. + * + * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000] + */ +#define BAUDRATE 115200 + +// Enable the Bluetooth serial interface on AT90USB devices +//#define BLUETOOTH + +// Choose the name from boards.h that matches your setup +#ifndef MOTHERBOARD + #define MOTHERBOARD BOARD_FYSETC_CHEETAH +#endif + +// Name displayed in the LCD "Ready" message and Info menu +//#define CUSTOM_MACHINE_NAME "3D Printer" + +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 +//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" + +// @section extruder + +// This defines the number of extruders +// :[1, 2, 3, 4, 5, 6] +#define EXTRUDERS 1 + +// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc. +#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 + +// For Cyclops or any "multi-extruder" that shares a single nozzle. +//#define SINGLENOZZLE + +/** + * Průša MK2 Single Nozzle Multi-Material Multiplexer, and variants. + * + * This device allows one stepper driver on a control board to drive + * two to eight stepper motors, one at a time, in a manner suitable + * for extruders. + * + * This option only allows the multiplexer to switch on tool-change. + * Additional options to configure custom E moves are pending. + */ +//#define MK2_MULTIPLEXER +#if ENABLED(MK2_MULTIPLEXER) + // Override the default DIO selector pins here, if needed. + // Some pins files may provide defaults for these pins. + //#define E_MUX0_PIN 40 // Always Required + //#define E_MUX1_PIN 42 // Needed for 3 to 8 inputs + //#define E_MUX2_PIN 44 // Needed for 5 to 8 inputs +#endif + +/** + * Prusa Multi-Material Unit v2 + * + * Requires NOZZLE_PARK_FEATURE to park print head in case MMU unit fails. + * Requires EXTRUDERS = 5 + * + * For additional configuration see Configuration_adv.h + */ +//#define PRUSA_MMU2 + +// A dual extruder that uses a single stepper motor +//#define SWITCHING_EXTRUDER +#if ENABLED(SWITCHING_EXTRUDER) + #define SWITCHING_EXTRUDER_SERVO_NR 0 + #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3] + #if EXTRUDERS > 3 + #define SWITCHING_EXTRUDER_E23_SERVO_NR 1 + #endif +#endif + +// A dual-nozzle that uses a servomotor to raise/lower one (or both) of the nozzles +//#define SWITCHING_NOZZLE +#if ENABLED(SWITCHING_NOZZLE) + #define SWITCHING_NOZZLE_SERVO_NR 0 + //#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second + #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo) +#endif + +/** + * Two separate X-carriages with extruders that connect to a moving part + * via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN. + */ +//#define PARKING_EXTRUDER + +/** + * Two separate X-carriages with extruders that connect to a moving part + * via a magnetic docking mechanism using movements and no solenoid + * + * project : https://www.thingiverse.com/thing:3080893 + * movements : https://youtu.be/0xCEiG9VS3k + * https://youtu.be/Bqbcs0CU2FE + */ +//#define MAGNETIC_PARKING_EXTRUDER + +#if EITHER(PARKING_EXTRUDER, MAGNETIC_PARKING_EXTRUDER) + + #define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders + #define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder + //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381 + + #if ENABLED(PARKING_EXTRUDER) + + #define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage + #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil + #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined. + //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381 + + #elif ENABLED(MAGNETIC_PARKING_EXTRUDER) + + #define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point + #define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple + #define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point + #define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling + + #endif + +#endif + +/** + * Switching Toolhead + * + * Support for swappable and dockable toolheads, such as + * the E3D Tool Changer. Toolheads are locked with a servo. + */ +//#define SWITCHING_TOOLHEAD + +/** + * Magnetic Switching Toolhead + * + * Support swappable and dockable toolheads with a magnetic + * docking mechanism using movement and no servo. + */ +//#define MAGNETIC_SWITCHING_TOOLHEAD + +/** + * Electromagnetic Switching Toolhead + * + * Parking for CoreXY / HBot kinematics. + * Toolheads are parked at one edge and held with an electromagnet. + * Supports more than 2 Toolheads. See https://youtu.be/JolbsAKTKf4 + */ +//#define ELECTROMAGNETIC_SWITCHING_TOOLHEAD + +#if ANY(SWITCHING_TOOLHEAD, MAGNETIC_SWITCHING_TOOLHEAD, ELECTROMAGNETIC_SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_Y_POS 235 // (mm) Y position of the toolhead dock + #define SWITCHING_TOOLHEAD_Y_SECURITY 10 // (mm) Security distance Y axis + #define SWITCHING_TOOLHEAD_Y_CLEAR 60 // (mm) Minimum distance from dock for unobstructed X axis + #define SWITCHING_TOOLHEAD_X_POS { 215, 0 } // (mm) X positions for parking the extruders + #if ENABLED(SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_SERVO_NR 2 // Index of the servo connector + #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock + #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif + #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching + #endif +#endif + +/** + * "Mixing Extruder" + * - Adds G-codes M163 and M164 to set and "commit" the current mix factors. + * - Extends the stepping routines to move multiple steppers in proportion to the mix. + * - Optional support for Repetier Firmware's 'M164 S' supporting virtual tools. + * - This implementation supports up to two mixing extruders. + * - Enable DIRECT_MIXING_IN_G1 for M165 and mixing in G1 (from Pia Taubert's reference implementation). + */ +//#define MIXING_EXTRUDER +#if ENABLED(MIXING_EXTRUDER) + #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder + #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164 + //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands + //#define GRADIENT_MIX // Support for gradient mixing with M166 and LCD + #if ENABLED(GRADIENT_MIX) + //#define GRADIENT_VTOOL // Add M166 T to use a V-tool index as a Gradient alias + #endif +#endif + +// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). +// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). +// For the other hotends it is their distance from the extruder 0 hotend. +//#define HOTEND_OFFSET_X { 0.0, 20.00 } // (mm) relative X-offset for each nozzle +//#define HOTEND_OFFSET_Y { 0.0, 5.00 } // (mm) relative Y-offset for each nozzle +//#define HOTEND_OFFSET_Z { 0.0, 0.00 } // (mm) relative Z-offset for each nozzle + +// @section machine + +/** + * Power Supply Control + * + * Enable and connect the power supply to the PS_ON_PIN. + * Specify whether the power supply is active HIGH or active LOW. + */ +//#define PSU_CONTROL +//#define PSU_NAME "Power Supply" + +#if ENABLED(PSU_CONTROL) + #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2) + + //#define PS_DEFAULT_OFF // Keep power off until enabled directly with M80 + + //#define AUTO_POWER_CONTROL // Enable automatic control of the PS_ON pin + #if ENABLED(AUTO_POWER_CONTROL) + #define AUTO_POWER_FANS // Turn on PSU if fans need power + #define AUTO_POWER_E_FANS + #define AUTO_POWER_CONTROLLERFAN + #define AUTO_POWER_CHAMBER_FAN + //#define AUTO_POWER_E_TEMP 50 // (°C) Turn on PSU over this temperature + //#define AUTO_POWER_CHAMBER_TEMP 30 // (°C) Turn on PSU over this temperature + #define POWER_TIMEOUT 30 + #endif +#endif + +// @section temperature + +//=========================================================================== +//============================= Thermal Settings ============================ +//=========================================================================== + +/** + * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table + * + * Temperature sensors available: + * + * -4 : thermocouple with AD8495 + * -3 : thermocouple with MAX31855 (only for sensor 0) + * -2 : thermocouple with MAX6675 (only for sensor 0) + * -1 : thermocouple with AD595 + * 0 : not used + * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 3 : Mendel-parts thermistor (4.7k pullup) + * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! + * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) + * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) + * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) + * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) + * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) + * 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) + * 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) + * 10 : 100k RS thermistor 198-961 (4.7k pullup) + * 11 : 100k beta 3950 1% thermistor (4.7k pullup) + * 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) + * 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" + * 15 : 100k thermistor calibration for JGAurora A5 hotend + * 18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327 + * 20 : the PT100 circuit found in the Ultimainboard V2.x + * 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 + * 61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup + * 66 : 4.7M High Temperature thermistor from Dyze Design + * 67 : 450C thermistor from SliceEngineering + * 70 : the 100K thermistor found in the bq Hephestos 2 + * 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor + * + * 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k. + * (but gives greater accuracy and more stable PID) + * 51 : 100k thermistor - EPCOS (1k pullup) + * 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup) + * 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) + * + * 1047 : Pt1000 with 4k7 pullup + * 1010 : Pt1000 with 1k pullup (non standard) + * 147 : Pt100 with 4k7 pullup + * 110 : Pt100 with 1k pullup (non standard) + * + * 1000 : Custom - Specify parameters in Configuration_adv.h + * + * Use these for Testing or Development purposes. NEVER for production machine. + * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. + * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. + * + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + */ +#define TEMP_SENSOR_0 1 +#define TEMP_SENSOR_1 0 +#define TEMP_SENSOR_2 0 +#define TEMP_SENSOR_3 0 +#define TEMP_SENSOR_4 0 +#define TEMP_SENSOR_5 0 +#define TEMP_SENSOR_BED 1 +#define TEMP_SENSOR_CHAMBER 0 + +// Dummy thermistor constant temperature readings, for use with 998 and 999 +#define DUMMY_THERMISTOR_998_VALUE 25 +#define DUMMY_THERMISTOR_999_VALUE 100 + +// Use temp sensor 1 as a redundant sensor with sensor 0. If the readings +// from the two sensors differ too much the print will be aborted. +//#define TEMP_SENSOR_1_AS_REDUNDANT +#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 + +#define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109 +#define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer +#define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target + +#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190 +#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer +#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target + +// Below this temperature the heater will be switched off +// because it probably indicates a broken thermistor wire. +#define HEATER_0_MINTEMP 5 +#define HEATER_1_MINTEMP 5 +#define HEATER_2_MINTEMP 5 +#define HEATER_3_MINTEMP 5 +#define HEATER_4_MINTEMP 5 +#define HEATER_5_MINTEMP 5 +#define BED_MINTEMP 5 + +// Above this temperature the heater will be switched off. +// This can protect components from overheating, but NOT from shorts and failures. +// (Use MINTEMP for thermistor short/failure protection.) +#define HEATER_0_MAXTEMP 275 +#define HEATER_1_MAXTEMP 275 +#define HEATER_2_MAXTEMP 275 +#define HEATER_3_MAXTEMP 275 +#define HEATER_4_MAXTEMP 275 +#define HEATER_5_MAXTEMP 275 +#define BED_MAXTEMP 150 + +//=========================================================================== +//============================= PID Settings ================================ +//=========================================================================== +// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning + +// Comment the following line to disable PID and enable bang-bang. +#define PIDTEMP +#define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current +#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current +#define PID_K1 0.95 // Smoothing factor within any PID loop +#if ENABLED(PIDTEMP) + //#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM) + //#define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM) + //#define PID_DEBUG // Sends debug data to the serial port. + //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX + //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay + //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] + #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature + // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. + + // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it + + //PID for Makerlab J-head + #define DEFAULT_Kp 21.73 + #define DEFAULT_Ki 1.54 + #define DEFAULT_Kd 76.55 + + // Ultimaker + //#define DEFAULT_Kp 22.2 + //#define DEFAULT_Ki 1.08 + //#define DEFAULT_Kd 114 + + // MakerGear + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 + + // Mendel Parts V9 on 12V + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 + +#endif // PIDTEMP + +//=========================================================================== +//====================== PID > Bed Temperature Control ====================== +//=========================================================================== + +/** + * PID Bed Heating + * + * If this option is enabled set PID constants below. + * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis. + * + * The PID frequency will be the same as the extruder PWM. + * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz, + * which is fine for driving a square wave into a resistive load and does not significantly + * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W + * heater. If your configuration is significantly different than this and you don't understand + * the issues involved, don't use bed PID until someone else verifies that your hardware works. + */ +//#define PIDTEMPBED + +//#define BED_LIMIT_SWITCHING + +/** + * Max Bed Power + * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis). + * When set to any value below 255, enables a form of PWM to the bed that acts like a divider + * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED) + */ +#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current + +#if ENABLED(PIDTEMPBED) + //#define MIN_BED_POWER 0 + //#define PID_BED_DEBUG // Sends debug data to the serial port. + + //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) + //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 + + //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) + //from pidautotune + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 + + // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. +#endif // PIDTEMPBED + +// @section extruder + +/** + * Prevent extrusion if the temperature is below EXTRUDE_MINTEMP. + * Add M302 to set the minimum extrusion temperature and/or turn + * cold extrusion prevention on and off. + * + * *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! *** + */ +#define PREVENT_COLD_EXTRUSION +#define EXTRUDE_MINTEMP 170 + +/** + * Prevent a single extrusion longer than EXTRUDE_MAXLENGTH. + * Note: For Bowden Extruders make this large enough to allow load/unload. + */ +#define PREVENT_LENGTHY_EXTRUDE +#define EXTRUDE_MAXLENGTH 200 + +//=========================================================================== +//======================== Thermal Runaway Protection ======================= +//=========================================================================== + +/** + * Thermal Protection provides additional protection to your printer from damage + * and fire. Marlin always includes safe min and max temperature ranges which + * protect against a broken or disconnected thermistor wire. + * + * The issue: If a thermistor falls out, it will report the much lower + * temperature of the air in the room, and the the firmware will keep + * the heater on. + * + * If you get "Thermal Runaway" or "Heating failed" errors the + * details can be tuned in Configuration_adv.h + */ + +#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders +#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed +#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber + +//=========================================================================== +//============================= Mechanical Settings ========================= +//=========================================================================== + +// @section machine + +// Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics +// either in the usual order or reversed +//#define COREXY +//#define COREXZ +//#define COREYZ +//#define COREYX +//#define COREZX +//#define COREZY + +//=========================================================================== +//============================== Endstop Settings =========================== +//=========================================================================== + +// @section homing + +// Specify here all the endstop connectors that are connected to any endstop or probe. +// Almost all printers will be using one per axis. Probes will use one or more of the +// extra connectors. Leave undefined any used for non-endstop and non-probe purposes. +#define USE_XMIN_PLUG +#define USE_YMIN_PLUG +#define USE_ZMIN_PLUG +//#define USE_XMAX_PLUG +//#define USE_YMAX_PLUG +//#define USE_ZMAX_PLUG + +// Enable pullup for all endstops to prevent a floating state +#define ENDSTOPPULLUPS +#if DISABLED(ENDSTOPPULLUPS) + // Disable ENDSTOPPULLUPS to set pullups individually + //#define ENDSTOPPULLUP_XMAX + //#define ENDSTOPPULLUP_YMAX + //#define ENDSTOPPULLUP_ZMAX + //#define ENDSTOPPULLUP_XMIN + //#define ENDSTOPPULLUP_YMIN + //#define ENDSTOPPULLUP_ZMIN + //#define ENDSTOPPULLUP_ZMIN_PROBE +#endif + +// Enable pulldown for all endstops to prevent a floating state +//#define ENDSTOPPULLDOWNS +#if DISABLED(ENDSTOPPULLDOWNS) + // Disable ENDSTOPPULLDOWNS to set pulldowns individually + //#define ENDSTOPPULLDOWN_XMAX + //#define ENDSTOPPULLDOWN_YMAX + //#define ENDSTOPPULLDOWN_ZMAX + //#define ENDSTOPPULLDOWN_XMIN + //#define ENDSTOPPULLDOWN_YMIN + //#define ENDSTOPPULLDOWN_ZMIN + //#define ENDSTOPPULLDOWN_ZMIN_PROBE +#endif + +// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup). +#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe. + +/** + * Stepper Drivers + * + * These settings allow Marlin to tune stepper driver timing and enable advanced options for + * stepper drivers that support them. You may also override timing options in Configuration_adv.h. + * + * A4988 is assumed for unspecified drivers. + * + * Options: A4988, A5984, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100, + * TMC2130, TMC2130_STANDALONE, TMC2160, TMC2160_STANDALONE, + * TMC2208, TMC2208_STANDALONE, TMC2209, TMC2209_STANDALONE, + * TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE, + * TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE + * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE'] + */ +#define X_DRIVER_TYPE TMC2209 +#define Y_DRIVER_TYPE TMC2209 +#define Z_DRIVER_TYPE TMC2209 +//#define X2_DRIVER_TYPE A4988 +//#define Y2_DRIVER_TYPE A4988 +//#define Z2_DRIVER_TYPE A4988 +//#define Z3_DRIVER_TYPE A4988 +#define E0_DRIVER_TYPE TMC2209 +//#define E1_DRIVER_TYPE A4988 +//#define E2_DRIVER_TYPE A4988 +//#define E3_DRIVER_TYPE A4988 +//#define E4_DRIVER_TYPE A4988 +//#define E5_DRIVER_TYPE A4988 + +// Enable this feature if all enabled endstop pins are interrupt-capable. +// This will remove the need to poll the interrupt pins, saving many CPU cycles. +//#define ENDSTOP_INTERRUPTS_FEATURE + +/** + * Endstop Noise Threshold + * + * Enable if your probe or endstops falsely trigger due to noise. + * + * - Higher values may affect repeatability or accuracy of some bed probes. + * - To fix noise install a 100nF ceramic capacitor inline with the switch. + * - This feature is not required for common micro-switches mounted on PCBs + * based on the Makerbot design, which already have the 100nF capacitor. + * + * :[2,3,4,5,6,7] + */ +//#define ENDSTOP_NOISE_THRESHOLD 2 + +//============================================================================= +//============================== Movement Settings ============================ +//============================================================================= +// @section motion + +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * With this option each E stepper can have its own factors for the + * following movement settings. If fewer factors are given than the + * total number of extruders, the last value applies to the rest. + */ +//#define DISTINCT_E_FACTORS + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] + */ +#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 93 } + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] + */ +#define DEFAULT_MAX_FEEDRATE { 500, 500, 5, 25 } + +/** + * Default Max Acceleration (change/s) change = mm/s + * (Maximum start speed for accelerated moves) + * Override with M201 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] + */ +#define DEFAULT_MAX_ACCELERATION { 500, 500, 100, 5000 } + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 500 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 500 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 500 // X, Y, Z acceleration for travel (non printing) moves + +/** + * Junction Deviation + * + * Use Junction Deviation instead of traditional Jerk Limiting + * + * See: + * https://reprap.org/forum/read.php?1,739819 + * http://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html + */ +//#define JUNCTION_DEVIATION +#if ENABLED(JUNCTION_DEVIATION) + #define JUNCTION_DEVIATION_MM 0.02 // (mm) Distance from real junction edge +#endif + +/** + * Default Jerk (mm/s) + * Override with M205 X Y Z E + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#if DISABLED(JUNCTION_DEVIATION) + #define DEFAULT_XJERK 10.0 + #define DEFAULT_YJERK 10.0 + #define DEFAULT_ZJERK 0.3 +#endif + +#define DEFAULT_EJERK 5.0 // May be used by Linear Advance + +/** + * S-Curve Acceleration + * + * This option eliminates vibration during printing by fitting a Bézier + * curve to move acceleration, producing much smoother direction changes. + * + * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained + */ +//#define S_CURVE_ACCELERATION + +//=========================================================================== +//============================= Z Probe Options ============================= +//=========================================================================== +// @section probes + +// +// See http://marlinfw.org/docs/configuration/probes.html +// + +/** + * Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + * + * Enable this option for a probe connected to the Z Min endstop pin. + */ +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +/** + * Z_MIN_PROBE_PIN + * + * Define this pin if the probe is not connected to Z_MIN_PIN. + * If not defined the default pin for the selected MOTHERBOARD + * will be used. Most of the time the default is what you want. + * + * - The simplest option is to use a free endstop connector. + * - Use 5V for powered (usually inductive) sensors. + * + * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin: + * - For simple switches connect... + * - normally-closed switches to GND and D32. + * - normally-open switches to 5V and D32. + * + */ +//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default + +/** + * Probe Type + * + * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. + * Activate one of these to use Auto Bed Leveling below. + */ + +/** + * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe. + * Use G29 repeatedly, adjusting the Z height at each point with movement commands + * or (with LCD_BED_LEVELING) the LCD controller. + */ +//#define PROBE_MANUALLY +//#define MANUAL_PROBE_START_Z 0.2 + +/** + * A Fix-Mounted Probe either doesn't deploy or needs manual deployment. + * (e.g., an inductive probe or a nozzle-based probe-switch.) + */ +//#define FIX_MOUNTED_PROBE + +/** + * Z Servo Probe, such as an endstop switch on a rotating arm. + */ +//#define Z_PROBE_SERVO_NR 0 // Defaults to SERVO 0 connector. +//#define Z_SERVO_ANGLES { 70, 0 } // Z Servo Deploy and Stow angles + +/** + * The BLTouch probe uses a Hall effect sensor and emulates a servo. + */ +//#define BLTOUCH + +/** + * Touch-MI Probe by hotends.fr + * + * This probe is deployed and activated by moving the X-axis to a magnet at the edge of the bed. + * By default, the magnet is assumed to be on the left and activated by a home. If the magnet is + * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position. + * + * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING, + * and a minimum Z_HOMING_HEIGHT of 10. + */ +//#define TOUCH_MI_PROBE +#if ENABLED(TOUCH_MI_PROBE) + #define TOUCH_MI_RETRACT_Z 0.5 // Height at which the probe retracts + //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2) // For a magnet on the right side of the bed + //#define TOUCH_MI_MANUAL_DEPLOY // For manual deploy (LCD menu) +#endif + +// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) +//#define SOLENOID_PROBE + +// A sled-mounted probe like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +// A probe deployed by moving the x-axis, such as the Wilson II's rack-and-pinion probe designed by Marty Rice. +//#define RACK_AND_PINION_PROBE +#if ENABLED(RACK_AND_PINION_PROBE) + #define Z_PROBE_DEPLOY_X X_MIN_POS + #define Z_PROBE_RETRACT_X X_MAX_POS +#endif + +// +// For Z_PROBE_ALLEN_KEY see the Delta example configurations. +// + +/** + * Z Probe to nozzle (X,Y) offset, relative to (0, 0). + * X and Y offsets must be integers. + * + * In the following example the X and Y offsets are both positive: + * #define X_PROBE_OFFSET_FROM_EXTRUDER 10 + * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 + * + * +-- BACK ---+ + * | | + * L | (+) P | R <-- probe (20,20) + * E | | I + * F | (-) N (+) | G <-- nozzle (10,10) + * T | | H + * | (-) | T + * | | + * O-- FRONT --+ + * (0,0) + */ +#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle] + +// Certain types of probes need to stay away from edges +#define MIN_PROBE_EDGE 10 + +// X and Y axis travel speed (mm/m) between probes +#define XY_PROBE_SPEED 8000 + +// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2) +#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z + +// Feedrate (mm/m) for the "accurate" probe of each point +#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) + +/** + * Multiple Probing + * + * You may get improved results by probing 2 or more times. + * With EXTRA_PROBING the more atypical reading(s) will be disregarded. + * + * A total of 2 does fast/slow probes with a weighted average. + * A total of 3 or more adds more slow probes, taking the average. + */ +//#define MULTIPLE_PROBING 2 +//#define EXTRA_PROBING 1 + +/** + * Z probes require clearance when deploying, stowing, and moving between + * probe points to avoid hitting the bed and other hardware. + * Servo-mounted probes require extra space for the arm to rotate. + * Inductive probes need space to keep from triggering early. + * + * Use these settings to specify the distance (mm) to raise the probe (or + * lower the bed). The values set here apply over and above any (negative) + * probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD. + * Only integer values >= 1 are valid here. + * + * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle. + * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle. + */ +#define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow +#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points +#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes +//#define Z_AFTER_PROBING 5 // Z position after probing is done + +#define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping + +// For M851 give a range for adjusting the Z probe offset +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + +// Enable the M48 repeatability test to test probe accuracy +//#define Z_MIN_PROBE_REPEATABILITY_TEST + +// Before deploy/stow pause for user confirmation +//#define PAUSE_BEFORE_DEPLOY_STOW +#if ENABLED(PAUSE_BEFORE_DEPLOY_STOW) + //#define PAUSE_PROBE_DEPLOY_WHEN_TRIGGERED // For Manual Deploy Allenkey Probe +#endif + +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + +// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 +// :{ 0:'Low', 1:'High' } +#define X_ENABLE_ON 0 +#define Y_ENABLE_ON 0 +#define Z_ENABLE_ON 0 +#define E_ENABLE_ON 0 // For all extruders + +// Disables axis stepper immediately when it's not being used. +// WARNING: When motors turn off there is a chance of losing position accuracy! +#define DISABLE_X false +#define DISABLE_Y false +#define DISABLE_Z false + +// Warn on display about possibly reduced accuracy +//#define DISABLE_REDUCED_ACCURACY_WARNING + +// @section extruder + +#define DISABLE_E false // For all extruders +#define DISABLE_INACTIVE_EXTRUDER // Keep only the active extruder enabled + +// @section machine + +// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way. +#define INVERT_X_DIR true +#define INVERT_Y_DIR true +#define INVERT_Z_DIR false + +// @section extruder + +// For direct drive extruder v9 set to true, for geared extruder set to false. +#define INVERT_E0_DIR true +#define INVERT_E1_DIR false +#define INVERT_E2_DIR false +#define INVERT_E3_DIR false +#define INVERT_E4_DIR false +#define INVERT_E5_DIR false + +// @section homing + +//#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed + +//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off. + +//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ... + // Be sure you have this distance over your Z_MAX_POS in case. + +// Direction of endstops when homing; 1=MAX, -1=MIN +// :[-1,1] +#define X_HOME_DIR -1 +#define Y_HOME_DIR -1 +#define Z_HOME_DIR -1 + +// @section machine + +// The size of the print bed +#define X_BED_SIZE 235 +#define Y_BED_SIZE 235 + +// Travel limits (mm) after homing, corresponding to endstop positions. +#define X_MIN_POS 0 +#define Y_MIN_POS 0 +#define Z_MIN_POS 0 +#define X_MAX_POS X_BED_SIZE +#define Y_MAX_POS Y_BED_SIZE +#define Z_MAX_POS 260 + +/** + * Software Endstops + * + * - Prevent moves outside the set machine bounds. + * - Individual axes can be disabled, if desired. + * - X and Y only apply to Cartesian robots. + * - Use 'M211' to set software endstops on/off or report current state + */ + +// Min software endstops constrain movement within minimum coordinate bounds +#define MIN_SOFTWARE_ENDSTOPS +#if ENABLED(MIN_SOFTWARE_ENDSTOPS) + #define MIN_SOFTWARE_ENDSTOP_X + #define MIN_SOFTWARE_ENDSTOP_Y + #define MIN_SOFTWARE_ENDSTOP_Z +#endif + +// Max software endstops constrain movement within maximum coordinate bounds +#define MAX_SOFTWARE_ENDSTOPS +#if ENABLED(MAX_SOFTWARE_ENDSTOPS) + #define MAX_SOFTWARE_ENDSTOP_X + #define MAX_SOFTWARE_ENDSTOP_Y + #define MAX_SOFTWARE_ENDSTOP_Z +#endif + +#if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS) + //#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD +#endif + +/** + * Filament Runout Sensors + * Mechanical or opto endstops are used to check for the presence of filament. + * + * RAMPS-based boards use SERVO3_PIN for the first runout sensor. + * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc. + * By default the firmware assumes HIGH=FILAMENT PRESENT. + */ +//#define FILAMENT_RUNOUT_SENSOR +#if ENABLED(FILAMENT_RUNOUT_SENSOR) + #define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each. + #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor. + #define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins. + //#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins. + + // Set one or more commands to execute on filament runout. + // (After 'M412 H' Marlin will ask the host to handle the process.) + #define FILAMENT_RUNOUT_SCRIPT "M600" + + // After a runout is detected, continue printing this length of filament + // before executing the runout script. Useful for a sensor at the end of + // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead. + //#define FILAMENT_RUNOUT_DISTANCE_MM 25 + + #ifdef FILAMENT_RUNOUT_DISTANCE_MM + // Enable this option to use an encoder disc that toggles the runout pin + // as the filament moves. (Be sure to set FILAMENT_RUNOUT_DISTANCE_MM + // large enough to avoid false positives.) + //#define FILAMENT_MOTION_SENSOR + #endif +#endif + +//=========================================================================== +//=============================== Bed Leveling ============================== +//=========================================================================== +// @section calibrate + +/** + * Choose one of the options below to enable G29 Bed Leveling. The parameters + * and behavior of G29 will change depending on your selection. + * + * If using a Probe for Z Homing, enable Z_SAFE_HOMING also! + * + * - AUTO_BED_LEVELING_3POINT + * Probe 3 arbitrary points on the bed (that aren't collinear) + * You specify the XY coordinates of all 3 points. + * The result is a single tilted plane. Best for a flat bed. + * + * - AUTO_BED_LEVELING_LINEAR + * Probe several points in a grid. + * You specify the rectangle and the density of sample points. + * The result is a single tilted plane. Best for a flat bed. + * + * - AUTO_BED_LEVELING_BILINEAR + * Probe several points in a grid. + * You specify the rectangle and the density of sample points. + * The result is a mesh, best for large or uneven beds. + * + * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling) + * A comprehensive bed leveling system combining the features and benefits + * of other systems. UBL also includes integrated Mesh Generation, Mesh + * Validation and Mesh Editing systems. + * + * - MESH_BED_LEVELING + * Probe a grid manually + * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.) + * For machines without a probe, Mesh Bed Leveling provides a method to perform + * leveling in steps so you can manually adjust the Z height at each grid-point. + * With an LCD controller the process is guided step-by-step. + */ +//#define AUTO_BED_LEVELING_3POINT +//#define AUTO_BED_LEVELING_LINEAR +//#define AUTO_BED_LEVELING_BILINEAR +//#define AUTO_BED_LEVELING_UBL +//#define MESH_BED_LEVELING + +/** + * Normally G28 leaves leveling disabled on completion. Enable + * this option to have G28 restore the prior leveling state. + */ +//#define RESTORE_LEVELING_AFTER_G28 + +/** + * Enable detailed logging of G28, G29, M48, etc. + * Turn on with the command 'M111 S32'. + * NOTE: Requires a lot of PROGMEM! + */ +//#define DEBUG_LEVELING_FEATURE + +#if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_BILINEAR, AUTO_BED_LEVELING_UBL) + // Gradually reduce leveling correction until a set height is reached, + // at which point movement will be level to the machine's XY plane. + // The height can be set with M420 Z + #define ENABLE_LEVELING_FADE_HEIGHT + + // For Cartesian machines, instead of dividing moves on mesh boundaries, + // split up moves into short segments like a Delta. This follows the + // contours of the bed more closely than edge-to-edge straight moves. + #define SEGMENT_LEVELED_MOVES + #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one) + + /** + * Enable the G26 Mesh Validation Pattern tool. + */ + //#define G26_MESH_VALIDATION + #if ENABLED(G26_MESH_VALIDATION) + #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle. + #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool. + #define MESH_TEST_HOTEND_TEMP 205 // (°C) Default nozzle temperature for the G26 Mesh Validation Tool. + #define MESH_TEST_BED_TEMP 60 // (°C) Default bed temperature for the G26 Mesh Validation Tool. + #define G26_XY_FEEDRATE 20 // (mm/s) Feedrate for XY Moves for the G26 Mesh Validation Tool. + #endif + +#endif + +#if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR) + + // Set the number of grid points per dimension. + #define GRID_MAX_POINTS_X 3 + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + // Set the boundaries for probing (where the probe can reach). + //#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE + //#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE)) + //#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE + //#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE)) + + // Probe along the Y axis, advancing X after each column + //#define PROBE_Y_FIRST + + #if ENABLED(AUTO_BED_LEVELING_BILINEAR) + + // Beyond the probed grid, continue the implied tilt? + // Default is to maintain the height of the nearest edge. + //#define EXTRAPOLATE_BEYOND_GRID + + // + // Experimental Subdivision of the grid by Catmull-Rom method. + // Synthesizes intermediate points to produce a more detailed mesh. + // + //#define ABL_BILINEAR_SUBDIVISION + #if ENABLED(ABL_BILINEAR_SUBDIVISION) + // Number of subdivisions between probe points + #define BILINEAR_SUBDIVISIONS 3 + #endif + + #endif + +#elif ENABLED(AUTO_BED_LEVELING_UBL) + + //=========================================================================== + //========================= Unified Bed Leveling ============================ + //=========================================================================== + + //#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh + + #define MESH_INSET 1 // Set Mesh bounds as an inset region of the bed + #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited. + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + #define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle + #define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500 + + //#define UBL_Z_RAISE_WHEN_OFF_MESH 2.5 // When the nozzle is off the mesh, this value is used + // as the Z-Height correction value. + +#elif ENABLED(MESH_BED_LEVELING) + + //=========================================================================== + //=================================== Mesh ================================== + //=========================================================================== + + #define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed + #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited. + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS + +#endif // BED_LEVELING + +/** + * Points to probe for all 3-point Leveling procedures. + * Override if the automatically selected points are inadequate. + */ +#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL) + //#define PROBE_PT_1_X 15 + //#define PROBE_PT_1_Y 180 + //#define PROBE_PT_2_X 15 + //#define PROBE_PT_2_Y 20 + //#define PROBE_PT_3_X 170 + //#define PROBE_PT_3_Y 20 +#endif + +/** + * Add a bed leveling sub-menu for ABL or MBL. + * Include a guided procedure if manual probing is enabled. + */ +//#define LCD_BED_LEVELING + +#if ENABLED(LCD_BED_LEVELING) + #define MESH_EDIT_Z_STEP 0.025 // (mm) Step size while manually probing Z axis. + #define LCD_PROBE_Z_RANGE 4 // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment + //#define MESH_EDIT_MENU // Add a menu to edit mesh points +#endif + +// Add a menu item to move between bed corners for manual bed adjustment +//#define LEVEL_BED_CORNERS + +#if ENABLED(LEVEL_BED_CORNERS) + #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner +#endif + +/** + * Commands to execute at the end of G29 probing. + * Useful to retract or move the Z probe out of the way. + */ +//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" + + +// @section homing + +// The center of the bed is at (X=0, Y=0) +//#define BED_CENTER_AT_0_0 + +// Manually set the home position. Leave these undefined for automatic settings. +// For DELTA this is the top-center of the Cartesian print volume. +//#define MANUAL_X_HOME_POS 0 +//#define MANUAL_Y_HOME_POS 0 +//#define MANUAL_Z_HOME_POS 0 + +// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area. +// +// With this feature enabled: +// +// - Allow Z homing only after X and Y homing AND stepper drivers still enabled. +// - If stepper drivers time out, it will need X and Y homing again before Z homing. +// - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28). +// - Prevent Z homing when the Z probe is outside bed area. +// +//#define Z_SAFE_HOMING + +#if ENABLED(Z_SAFE_HOMING) + #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing when homing all axes (G28). + #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2) // Y point for Z homing when homing all axes (G28). +#endif + +// Homing speeds (mm/m) +#define HOMING_FEEDRATE_XY (50*60) +#define HOMING_FEEDRATE_Z (4*60) + +// Validate that endstops are triggered on homing moves +#define VALIDATE_HOMING_ENDSTOPS + +// @section calibrate + +/** + * Bed Skew Compensation + * + * This feature corrects for misalignment in the XYZ axes. + * + * Take the following steps to get the bed skew in the XY plane: + * 1. Print a test square (e.g., https://www.thingiverse.com/thing:2563185) + * 2. For XY_DIAG_AC measure the diagonal A to C + * 3. For XY_DIAG_BD measure the diagonal B to D + * 4. For XY_SIDE_AD measure the edge A to D + * + * Marlin automatically computes skew factors from these measurements. + * Skew factors may also be computed and set manually: + * + * - Compute AB : SQRT(2*AC*AC+2*BD*BD-4*AD*AD)/2 + * - XY_SKEW_FACTOR : TAN(PI/2-ACOS((AC*AC-AB*AB-AD*AD)/(2*AB*AD))) + * + * If desired, follow the same procedure for XZ and YZ. + * Use these diagrams for reference: + * + * Y Z Z + * ^ B-------C ^ B-------C ^ B-------C + * | / / | / / | / / + * | / / | / / | / / + * | A-------D | A-------D | A-------D + * +-------------->X +-------------->X +-------------->Y + * XY_SKEW_FACTOR XZ_SKEW_FACTOR YZ_SKEW_FACTOR + */ +//#define SKEW_CORRECTION + +#if ENABLED(SKEW_CORRECTION) + // Input all length measurements here: + #define XY_DIAG_AC 282.8427124746 + #define XY_DIAG_BD 282.8427124746 + #define XY_SIDE_AD 200 + + // Or, set the default skew factors directly here + // to override the above measurements: + #define XY_SKEW_FACTOR 0.0 + + //#define SKEW_CORRECTION_FOR_Z + #if ENABLED(SKEW_CORRECTION_FOR_Z) + #define XZ_DIAG_AC 282.8427124746 + #define XZ_DIAG_BD 282.8427124746 + #define YZ_DIAG_AC 282.8427124746 + #define YZ_DIAG_BD 282.8427124746 + #define YZ_SIDE_AD 200 + #define XZ_SKEW_FACTOR 0.0 + #define YZ_SKEW_FACTOR 0.0 + #endif + + // Enable this option for M852 to set skew at runtime + //#define SKEW_CORRECTION_GCODE +#endif + +//============================================================================= +//============================= Additional Features =========================== +//============================================================================= + +// @section extras + +/** + * EEPROM + * + * Persistent storage to preserve configurable settings across reboots. + * + * M500 - Store settings to EEPROM. + * M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes) + * M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.) + */ +#define EEPROM_SETTINGS // Persistent storage with M500 and M501 +//#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release! +#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM. +#if ENABLED(EEPROM_SETTINGS) + //#define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors. +#endif + +// +// Host Keepalive +// +// When enabled Marlin will send a busy status message to the host +// every couple of seconds when it can't accept commands. +// +#define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages +#define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113. +#define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating + +// +// M100 Free Memory Watcher +// +//#define M100_FREE_MEMORY_WATCHER // Add M100 (Free Memory Watcher) to debug memory usage + +// +// G20/G21 Inch mode support +// +//#define INCH_MODE_SUPPORT + +// +// M149 Set temperature units support +// +//#define TEMPERATURE_UNITS_SUPPORT + +// @section temperature + +// Preheat Constants +#define PREHEAT_1_LABEL "PLA" +#define PREHEAT_1_TEMP_HOTEND 180 +#define PREHEAT_1_TEMP_BED 70 +#define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255 + +#define PREHEAT_2_LABEL "ABS" +#define PREHEAT_2_TEMP_HOTEND 240 +#define PREHEAT_2_TEMP_BED 110 +#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255 + +/** + * Nozzle Park + * + * Park the nozzle at the given XYZ position on idle or G27. + * + * The "P" parameter controls the action applied to the Z axis: + * + * P0 (Default) If Z is below park Z raise the nozzle. + * P1 Raise the nozzle always to Z-park height. + * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS. + */ +//#define NOZZLE_PARK_FEATURE + +#if ENABLED(NOZZLE_PARK_FEATURE) + // Specify a park position as { X, Y, Z_raise } + #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 } + #define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis) + #define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers) +#endif + +/** + * Clean Nozzle Feature -- EXPERIMENTAL + * + * Adds the G12 command to perform a nozzle cleaning process. + * + * Parameters: + * P Pattern + * S Strokes / Repetitions + * T Triangles (P1 only) + * + * Patterns: + * P0 Straight line (default). This process requires a sponge type material + * at a fixed bed location. "S" specifies strokes (i.e. back-forth motions) + * between the start / end points. + * + * P1 Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the + * number of zig-zag triangles to do. "S" defines the number of strokes. + * Zig-zags are done in whichever is the narrower dimension. + * For example, "G12 P1 S1 T3" will execute: + * + * -- + * | (X0, Y1) | /\ /\ /\ | (X1, Y1) + * | | / \ / \ / \ | + * A | | / \ / \ / \ | + * | | / \ / \ / \ | + * | (X0, Y0) | / \/ \/ \ | (X1, Y0) + * -- +--------------------------------+ + * |________|_________|_________| + * T1 T2 T3 + * + * P2 Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE. + * "R" specifies the radius. "S" specifies the stroke count. + * Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT. + * + * Caveats: The ending Z should be the same as starting Z. + * Attention: EXPERIMENTAL. G-code arguments may change. + * + */ +//#define NOZZLE_CLEAN_FEATURE + +#if ENABLED(NOZZLE_CLEAN_FEATURE) + // Default number of pattern repetitions + #define NOZZLE_CLEAN_STROKES 12 + + // Default number of triangles + #define NOZZLE_CLEAN_TRIANGLES 3 + + // Specify positions as { X, Y, Z } + #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)} + #define NOZZLE_CLEAN_END_POINT { 100, 60, (Z_MIN_POS + 1) } + + // Circular pattern radius + #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5 + // Circular pattern circle fragments number + #define NOZZLE_CLEAN_CIRCLE_FN 10 + // Middle point of circle + #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT + + // Move the nozzle to the initial position after cleaning + #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z +#endif + +/** + * Print Job Timer + * + * Automatically start and stop the print job timer on M104/M109/M190. + * + * M104 (hotend, no wait) - high temp = none, low temp = stop timer + * M109 (hotend, wait) - high temp = start timer, low temp = stop timer + * M190 (bed, wait) - high temp = start timer, low temp = none + * + * The timer can also be controlled with the following commands: + * + * M75 - Start the print job timer + * M76 - Pause the print job timer + * M77 - Stop the print job timer + */ +#define PRINTJOB_TIMER_AUTOSTART + +/** + * Print Counter + * + * Track statistical data such as: + * + * - Total print jobs + * - Total successful print jobs + * - Total failed print jobs + * - Total time printing + * + * View the current statistics with M78. + */ +//#define PRINTCOUNTER + +//============================================================================= +//============================= LCD and SD support ============================ +//============================================================================= + +// @section lcd + +/** + * LCD LANGUAGE + * + * Select the language to display on the LCD. These languages are available: + * + * en, an, bg, ca, cz, da, de, el, el-gr, es, eu, fi, fr, gl, hr, it, + * jp-kana, ko_KR, nl, pl, pt, pt-br, ru, sk, tr, uk, zh_CN, zh_TW, test + * + * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cz':'Czech', 'da':'Danish', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'jp-kana':'Japanese', 'ko_KR':'Korean (South Korea)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'ru':'Russian', 'sk':'Slovak', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Traditional)', 'test':'TEST' } + */ +#define LCD_LANGUAGE en + +/** + * LCD Character Set + * + * Note: This option is NOT applicable to Graphical Displays. + * + * All character-based LCDs provide ASCII plus one of these + * language extensions: + * + * - JAPANESE ... the most common + * - WESTERN ... with more accented characters + * - CYRILLIC ... for the Russian language + * + * To determine the language extension installed on your controller: + * + * - Compile and upload with LCD_LANGUAGE set to 'test' + * - Click the controller to view the LCD menu + * - The LCD will display Japanese, Western, or Cyrillic text + * + * See http://marlinfw.org/docs/development/lcd_language.html + * + * :['JAPANESE', 'WESTERN', 'CYRILLIC'] + */ +#define DISPLAY_CHARSET_HD44780 JAPANESE + +/** + * Info Screen Style (0:Classic, 1:Prusa) + * + * :[0:'Classic', 1:'Prusa'] + */ +#define LCD_INFO_SCREEN_STYLE 0 + +/** + * SD CARD + * + * SD Card support is disabled by default. If your controller has an SD slot, + * you must uncomment the following option or it won't work. + * + */ +#define SDSUPPORT + +/** + * SD CARD: SPI SPEED + * + * Enable one of the following items for a slower SPI transfer speed. + * This may be required to resolve "volume init" errors. + */ +//#define SPI_SPEED SPI_HALF_SPEED +//#define SPI_SPEED SPI_QUARTER_SPEED +//#define SPI_SPEED SPI_EIGHTH_SPEED + +/** + * SD CARD: ENABLE CRC + * + * Use CRC checks and retries on the SD communication. + */ +//#define SD_CHECK_AND_RETRY + +/** + * LCD Menu Items + * + * Disable all menus and only display the Status Screen, or + * just remove some extraneous menu items to recover space. + */ +//#define NO_LCD_MENUS +//#define SLIM_LCD_MENUS + +// +// ENCODER SETTINGS +// +// This option overrides the default number of encoder pulses needed to +// produce one step. Should be increased for high-resolution encoders. +// +//#define ENCODER_PULSES_PER_STEP 4 + +// +// Use this option to override the number of step signals required to +// move between next/prev menu items. +// +//#define ENCODER_STEPS_PER_MENU_ITEM 1 + +/** + * Encoder Direction Options + * + * Test your encoder's behavior first with both options disabled. + * + * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION. + * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION. + * Reversed Value Editing only? Enable BOTH options. + */ + +// +// This option reverses the encoder direction everywhere. +// +// Set this option if CLOCKWISE causes values to DECREASE +// +//#define REVERSE_ENCODER_DIRECTION + +// +// This option reverses the encoder direction for navigating LCD menus. +// +// If CLOCKWISE normally moves DOWN this makes it go UP. +// If CLOCKWISE normally moves UP this makes it go DOWN. +// +//#define REVERSE_MENU_DIRECTION + +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + +// +// Individual Axis Homing +// +// Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu. +// +//#define INDIVIDUAL_AXIS_HOMING_MENU + +// +// SPEAKER/BUZZER +// +// If you have a speaker that can produce tones, enable it here. +// By default Marlin assumes you have a buzzer with a fixed frequency. +// +//#define SPEAKER + +// +// The duration and frequency for the UI feedback sound. +// Set these to 0 to disable audio feedback in the LCD menus. +// +// Note: Test audio output with the G-Code: +// M300 S P +// +//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 2 +//#define LCD_FEEDBACK_FREQUENCY_HZ 5000 + +//============================================================================= +//======================== LCD / Controller Selection ========================= +//======================== (Character-based LCDs) ========================= +//============================================================================= + +// +// RepRapDiscount Smart Controller. +// http://reprap.org/wiki/RepRapDiscount_Smart_Controller +// +// Note: Usually sold with a white PCB. +// +//#define REPRAP_DISCOUNT_SMART_CONTROLLER + +// +// Original RADDS LCD Display+Encoder+SDCardReader +// http://doku.radds.org/dokumentation/lcd-display/ +// +//#define RADDS_DISPLAY + +// +// ULTIMAKER Controller. +// +//#define ULTIMAKERCONTROLLER + +// +// ULTIPANEL as seen on Thingiverse. +// +//#define ULTIPANEL + +// +// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3) +// http://reprap.org/wiki/PanelOne +// +//#define PANEL_ONE + +// +// GADGETS3D G3D LCD/SD Controller +// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel +// +// Note: Usually sold with a blue PCB. +// +//#define G3D_PANEL + +// +// RigidBot Panel V1.0 +// http://www.inventapart.com/ +// +//#define RIGIDBOT_PANEL + +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// ANET and Tronxy 20x4 Controller +// +//#define ZONESTAR_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin. + // This LCD is known to be susceptible to electrical interference + // which scrambles the display. Pressing any button clears it up. + // This is a LCD2004 display with 5 analog buttons. + +// +// Generic 16x2, 16x4, 20x2, or 20x4 character-based LCD. +// +//#define ULTRA_LCD + +//============================================================================= +//======================== LCD / Controller Selection ========================= +//===================== (I2C and Shift-Register LCDs) ===================== +//============================================================================= + +// +// CONTROLLER TYPE: I2C +// +// Note: These controllers require the installation of Arduino's LiquidCrystal_I2C +// library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C +// + +// +// Elefu RA Board Control Panel +// http://www.elefu.com/index.php?route=product/product&product_id=53 +// +//#define RA_CONTROL_PANEL + +// +// Sainsmart (YwRobot) LCD Displays +// +// These require F.Malpartida's LiquidCrystal_I2C library +// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home +// +//#define LCD_SAINSMART_I2C_1602 +//#define LCD_SAINSMART_I2C_2004 + +// +// Generic LCM1602 LCD adapter +// +//#define LCM1602 + +// +// PANELOLU2 LCD with status LEDs, +// separate encoder and click inputs. +// +// Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later. +// For more info: https://github.com/lincomatic/LiquidTWI2 +// +// Note: The PANELOLU2 encoder click input can either be directly connected to +// a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1). +// +//#define LCD_I2C_PANELOLU2 + +// +// Panucatt VIKI LCD with status LEDs, +// integrated click & L/R/U/D buttons, separate encoder inputs. +// +//#define LCD_I2C_VIKI + +// +// CONTROLLER TYPE: Shift register panels +// + +// +// 2-wire Non-latching LCD SR from https://goo.gl/aJJ4sH +// LCD configuration: http://reprap.org/wiki/SAV_3D_LCD +// +//#define SAV_3DLCD + +// +// 3-wire SR LCD with strobe using 74HC4094 +// https://github.com/mikeshub/SailfishLCD +// Uses the code directly from Sailfish +// +//#define FF_INTERFACEBOARD + +//============================================================================= +//======================= LCD / Controller Selection ======================= +//========================= (Graphical LCDs) ======================== +//============================================================================= + +// +// CONTROLLER TYPE: Graphical 128x64 (DOGM) +// +// IMPORTANT: The U8glib library is required for Graphical Display! +// https://github.com/olikraus/U8glib_Arduino +// + +// +// RepRapDiscount FULL GRAPHIC Smart Controller +// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller +// +#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER + +// +// ReprapWorld Graphical LCD +// https://reprapworld.com/?products_details&products_id/1218 +// +//#define REPRAPWORLD_GRAPHICAL_LCD + +// +// Activate one of these if you have a Panucatt Devices +// Viki 2.0 or mini Viki with Graphic LCD +// http://panucatt.com +// +//#define VIKI2 +//#define miniVIKI + +// +// MakerLab Mini Panel with graphic +// controller and SD support - http://reprap.org/wiki/Mini_panel +// +//#define MINIPANEL + +// +// MaKr3d Makr-Panel with graphic controller and SD support. +// http://reprap.org/wiki/MaKr3d_MaKrPanel +// +//#define MAKRPANEL + +// +// Adafruit ST7565 Full Graphic Controller. +// https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/ +// +//#define ELB_FULL_GRAPHIC_CONTROLLER + +// +// BQ LCD Smart Controller shipped by +// default with the BQ Hephestos 2 and Witbox 2. +// +//#define BQ_LCD_SMART_CONTROLLER + +// +// Cartesio UI +// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// +//#define CARTESIO_UI + +// +// LCD for Melzi Card with Graphical LCD +// +//#define LCD_FOR_MELZI + +// +// Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder +// https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) +// +//#define ULTI_CONTROLLER + +// +// MKS MINI12864 with graphic controller and SD support +// https://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// FYSETC variant of the MINI12864 graphic controller with SD support +// https://wiki.fysetc.com/Mini12864_Panel/ +// +//#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default +//#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) +//#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// ANET and Tronxy Graphical Controller +// +// Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6 +// A clone of the RepRapDiscount full graphics display but with +// different pins/wiring (see pins_ANET_10.h). +// +//#define ANET_FULL_GRAPHICS_LCD + +// +// AZSMZ 12864 LCD with SD +// https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html +// +//#define AZSMZ_12864 + +// +// Silvergate GLCD controller +// http://github.com/android444/Silvergate +// +//#define SILVER_GATE_GLCD_CONTROLLER + +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + +//============================================================================= +//========================== Extensible UI Displays =========================== +//============================================================================= + +// +// DGUS Touch Display with DWIN OS +// +//#define DGUS_LCD + +// +// Touch-screen LCD for Malyan M200 printers +// +//#define MALYAN_LCD + +// +// Third-party or vendor-customized controller interfaces. +// Sources should be installed in 'src/lcd/extensible_ui'. +// +//#define EXTENSIBLE_UI + +//============================================================================= +//=============================== Graphical TFTs ============================== +//============================================================================= + +// +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) +// +//#define FSMC_GRAPHICAL_TFT + +//============================================================================= +//============================ Other Controllers ============================ +//============================================================================= + +// +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 +// +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif + +// +// RepRapWorld REPRAPWORLD_KEYPAD v1.1 +// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626 +// +// REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key +// is pressed, a value of 10.0 means 10mm per click. +// +//#define REPRAPWORLD_KEYPAD +//#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 + +//============================================================================= +//=============================== Extra Features ============================== +//============================================================================= + +// @section extras + +// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino +//#define FAST_PWM_FAN + +// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency +// which is not as annoying as with the hardware PWM. On the other hand, if this frequency +// is too low, you should also increment SOFT_PWM_SCALE. +//#define FAN_SOFT_PWM + +// Incrementing this by 1 will double the software PWM frequency, +// affecting heaters, and the fan if FAN_SOFT_PWM is enabled. +// However, control resolution will be halved for each increment; +// at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] +#define SOFT_PWM_SCALE 0 + +// If SOFT_PWM_SCALE is set to a value higher than 0, dithering can +// be used to mitigate the associated resolution loss. If enabled, +// some of the PWM cycles are stretched so on average the desired +// duty cycle is attained. +//#define SOFT_PWM_DITHER + +// Temperature status LEDs that display the hotend and bed temperature. +// If all hotends, bed temperature, and target temperature are under 54C +// then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis) +//#define TEMP_STAT_LEDS + +// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure +//#define SF_ARC_FIX + +// Support for the BariCUDA Paste Extruder +//#define BARICUDA + +// Support for BlinkM/CyzRgb +//#define BLINKM + +// Support for PCA9632 PWM LED driver +//#define PCA9632 + +// Support for PCA9533 PWM LED driver +// https://github.com/mikeshub/SailfishRGB_LED +//#define PCA9533 + +/** + * RGB LED / LED Strip Control + * + * Enable support for an RGB LED connected to 5V digital pins, or + * an RGB Strip connected to MOSFETs controlled by digital pins. + * + * Adds the M150 command to set the LED (or LED strip) color. + * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of + * luminance values can be set from 0 to 255. + * For Neopixel LED an overall brightness parameter is also available. + * + * *** CAUTION *** + * LED Strips require a MOSFET Chip between PWM lines and LEDs, + * as the Arduino cannot handle the current the LEDs will require. + * Failure to follow this precaution can destroy your Arduino! + * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * more current than the Arduino 5V linear regulator can produce. + * *** CAUTION *** + * + * LED Type. Enable only one of the following two options. + * + */ +#define RGB_LED +//#define RGBW_LED + +#if EITHER(RGB_LED, RGBW_LED) + //#define RGB_LED_R_PIN 34 + //#define RGB_LED_G_PIN 43 + //#define RGB_LED_B_PIN 35 + //#define RGB_LED_W_PIN -1 +#endif + +// Support for Adafruit Neopixel LED driver +//#define NEOPIXEL_LED +#if ENABLED(NEOPIXEL_LED) + #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. + #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) + //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup + + // Use a single Neopixel LED for static (background) lighting + //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use + //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W +#endif + +/** + * Printer Event LEDs + * + * During printing, the LEDs will reflect the printer status: + * + * - Gradually change from blue to violet as the heated bed gets to target temp + * - Gradually change from violet to red as the hotend gets to temperature + * - Change to white to illuminate work surface + * - Change to green once print has finished + * - Turn off after the print has finished and the user has pushed a button + */ +#if ANY(BLINKM, RGB_LED, RGBW_LED, PCA9632, PCA9533, NEOPIXEL_LED) + #define PRINTER_EVENT_LEDS +#endif + +/** + * R/C SERVO support + * Sponsored by TrinityLabs, Reworked by codexmas + */ + +/** + * Number of servos + * + * For some servo-related options NUM_SERVOS will be set automatically. + * Set this manually if there are extra servos needing manual control. + * Leave undefined or set to 0 to entirely disable the servo subsystem. + */ +//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command + +// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. +// 300ms is a good value but you can try less delay. +// If the servo can't reach the requested position, increase it. +#define SERVO_DELAY { 300 } + +// Only power servos during movement, otherwise leave off to prevent jitter +//#define DEACTIVATE_SERVOS_AFTER_MOVE + +// Allow servo angle to be edited and saved to EEPROM +//#define EDITABLE_SERVO_ANGLES + +/** + * Sometimes after inserting the SD card settings get lost. + * This option reloads settings when the SD card is inserted. + */ +#define SD_RELOAD_SETTINGS diff --git a/config/examples/FYSETC/Cheetah/base/Configuration_adv.h b/config/examples/FYSETC/Cheetah/base/Configuration_adv.h new file mode 100644 index 0000000000..f59721ae05 --- /dev/null +++ b/config/examples/FYSETC/Cheetah/base/Configuration_adv.h @@ -0,0 +1,2561 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Configuration_adv.h + * + * Advanced settings. + * Only change these if you know exactly what you're doing. + * Some of these settings can damage your printer if improperly set! + * + * Basic settings can be found in Configuration.h + * + */ +#define CONFIGURATION_ADV_H_VERSION 020000 + +// @section temperature + +//=========================================================================== +//=============================Thermal Settings ============================ +//=========================================================================== + +// +// Custom Thermistor 1000 parameters +// +#if TEMP_SENSOR_0 == 1000 + #define HOTEND0_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND0_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND0_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_1 == 1000 + #define HOTEND1_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND1_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND1_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_2 == 1000 + #define HOTEND2_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND2_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND2_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_3 == 1000 + #define HOTEND3_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND3_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND3_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_4 == 1000 + #define HOTEND4_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND4_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND4_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_5 == 1000 + #define HOTEND5_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND5_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND5_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_BED == 1000 + #define BED_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define BED_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define BED_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_CHAMBER == 1000 + #define CHAMBER_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define CHAMBER_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define CHAMBER_BETA 3950 // Beta value +#endif + +// +// Hephestos 2 24V heated bed upgrade kit. +// https://store.bq.com/en/heated-bed-kit-hephestos2 +// +//#define HEPHESTOS2_HEATED_BED_KIT +#if ENABLED(HEPHESTOS2_HEATED_BED_KIT) + #undef TEMP_SENSOR_BED + #define TEMP_SENSOR_BED 70 + #define HEATER_BED_INVERTING true +#endif + +/** + * Heated Chamber settings + */ +#if TEMP_SENSOR_CHAMBER + #define CHAMBER_MINTEMP 5 + #define CHAMBER_MAXTEMP 60 + #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target + //#define CHAMBER_LIMIT_SWITCHING + //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin + //#define HEATER_CHAMBER_INVERTING false +#endif + +#if DISABLED(PIDTEMPBED) + #define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control + #if ENABLED(BED_LIMIT_SWITCHING) + #define BED_HYSTERESIS 2 // Only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS + #endif +#endif + +/** + * Thermal Protection provides additional protection to your printer from damage + * and fire. Marlin always includes safe min and max temperature ranges which + * protect against a broken or disconnected thermistor wire. + * + * The issue: If a thermistor falls out, it will report the much lower + * temperature of the air in the room, and the the firmware will keep + * the heater on. + * + * The solution: Once the temperature reaches the target, start observing. + * If the temperature stays too far below the target (hysteresis) for too + * long (period), the firmware will halt the machine as a safety precaution. + * + * If you get false positives for "Thermal Runaway", increase + * THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD + */ +#if ENABLED(THERMAL_PROTECTION_HOTENDS) + #define THERMAL_PROTECTION_PERIOD 40 // Seconds + #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius + + //#define ADAPTIVE_FAN_SLOWING // Slow part cooling fan if temperature drops + #if BOTH(ADAPTIVE_FAN_SLOWING, PIDTEMP) + //#define NO_FAN_SLOWING_IN_PID_TUNING // Don't slow fan speed during M303 + #endif + + /** + * Whenever an M104, M109, or M303 increases the target temperature, the + * firmware will wait for the WATCH_TEMP_PERIOD to expire. If the temperature + * hasn't increased by WATCH_TEMP_INCREASE degrees, the machine is halted and + * requires a hard reset. This test restarts with any M104/M109/M303, but only + * if the current temperature is far enough below the target for a reliable + * test. + * + * If you get false positives for "Heating failed", increase WATCH_TEMP_PERIOD + * and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set + * below 2. + */ + #define WATCH_TEMP_PERIOD 120 // Seconds + #define WATCH_TEMP_INCREASE 2 // Degrees Celsius +#endif + +/** + * Thermal Protection parameters for the bed are just as above for hotends. + */ +#if ENABLED(THERMAL_PROTECTION_BED) + #define THERMAL_PROTECTION_BED_PERIOD 60 // Seconds + #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius + + /** + * As described above, except for the bed (M140/M190/M303). + */ + #define WATCH_BED_TEMP_PERIOD 100 // Seconds + #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius +#endif + +/** + * Thermal Protection parameters for the heated chamber. + */ +#if ENABLED(THERMAL_PROTECTION_CHAMBER) + #define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds + #define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius + + /** + * Heated chamber watch settings (M141/M191). + */ + #define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds + #define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius +#endif + +#if ENABLED(PIDTEMP) + // Add an experimental additional term to the heater power, proportional to the extrusion speed. + // A well-chosen Kc value should add just enough power to melt the increased material volume. + //#define PID_EXTRUSION_SCALING + #if ENABLED(PID_EXTRUSION_SCALING) + #define DEFAULT_Kc (100) //heating power=Kc*(e_speed) + #define LPQ_MAX_LEN 50 + #endif +#endif + +/** + * Automatic Temperature: + * The hotend target temperature is calculated by all the buffered lines of gcode. + * The maximum buffered steps/sec of the extruder motor is called "se". + * Start autotemp mode with M109 S B F + * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by + * mintemp and maxtemp. Turn this off by executing M109 without F* + * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp. + * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode + */ +#define AUTOTEMP +#if ENABLED(AUTOTEMP) + #define AUTOTEMP_OLDWEIGHT 0.98 +#endif + +// Show extra position information in M114 +//#define M114_DETAIL + +// Show Temperature ADC value +// Enable for M105 to include ADC values read from temperature sensors. +//#define SHOW_TEMP_ADC_VALUES + +/** + * High Temperature Thermistor Support + * + * Thermistors able to support high temperature tend to have a hard time getting + * good readings at room and lower temperatures. This means HEATER_X_RAW_LO_TEMP + * will probably be caught when the heating element first turns on during the + * preheating process, which will trigger a min_temp_error as a safety measure + * and force stop everything. + * To circumvent this limitation, we allow for a preheat time (during which, + * min_temp_error won't be triggered) and add a min_temp buffer to handle + * aberrant readings. + * + * If you want to enable this feature for your hotend thermistor(s) + * uncomment and set values > 0 in the constants below + */ + +// The number of consecutive low temperature errors that can occur +// before a min_temp_error is triggered. (Shouldn't be more than 10.) +//#define MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED 0 + +// The number of milliseconds a hotend will preheat before starting to check +// the temperature. This value should NOT be set to the time it takes the +// hot end to reach the target temperature, but the time it takes to reach +// the minimum temperature your thermistor can read. The lower the better/safer. +// This shouldn't need to be more than 30 seconds (30000) +//#define MILLISECONDS_PREHEAT_TIME 0 + +// @section extruder + +// Extruder runout prevention. +// If the machine is idle and the temperature over MINTEMP +// then extrude some filament every couple of SECONDS. +//#define EXTRUDER_RUNOUT_PREVENT +#if ENABLED(EXTRUDER_RUNOUT_PREVENT) + #define EXTRUDER_RUNOUT_MINTEMP 190 + #define EXTRUDER_RUNOUT_SECONDS 30 + #define EXTRUDER_RUNOUT_SPEED 1500 // (mm/m) + #define EXTRUDER_RUNOUT_EXTRUDE 5 // (mm) +#endif + +// @section temperature + +// Calibration for AD595 / AD8495 sensor to adjust temperature measurements. +// The final temperature is calculated as (measuredTemp * GAIN) + OFFSET. +#define TEMP_SENSOR_AD595_OFFSET 0.0 +#define TEMP_SENSOR_AD595_GAIN 1.0 +#define TEMP_SENSOR_AD8495_OFFSET 0.0 +#define TEMP_SENSOR_AD8495_GAIN 1.0 + +/** + * Controller Fan + * To cool down the stepper drivers and MOSFETs. + * + * The fan will turn on automatically whenever any stepper is enabled + * and turn off after a set period after all steppers are turned off. + */ +//#define USE_CONTROLLER_FAN +#if ENABLED(USE_CONTROLLER_FAN) + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled + #define CONTROLLERFAN_SPEED 255 // 255 == full speed +#endif + +// When first starting the main fan, run it at full speed for the +// given number of milliseconds. This gets the fan spinning reliably +// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) +//#define FAN_KICKSTART_TIME 100 + +/** + * PWM Fan Scaling + * + * Define the min/max speeds for PWM fans (as set with M106). + * + * With these options the M106 0-255 value range is scaled to a subset + * to ensure that the fan has enough power to spin, or to run lower + * current fans with higher current. (e.g., 5V/12V fans with 12V/24V) + * Value 0 always turns off the fan. + * + * Define one or both of these to override the default 0-255 range. + */ +//#define FAN_MIN_PWM 50 +//#define FAN_MAX_PWM 128 + +/** + * FAST PWM FAN Settings + * + * Use to change the FAST FAN PWM frequency (if enabled in Configuration.h) + * Combinations of PWM Modes, prescale values and TOP resolutions are used internally to produce a + * frequency as close as possible to the desired frequency. + * + * FAST_PWM_FAN_FREQUENCY [undefined by default] + * Set this to your desired frequency. + * If left undefined this defaults to F = F_CPU/(2*255*1) + * ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers + * These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required + * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior. + * + * USE_OCR2A_AS_TOP [undefined by default] + * Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2: + * 16MHz MCUs: [62.5KHz, 31.4KHz (default), 7.8KHz, 3.92KHz, 1.95KHz, 977Hz, 488Hz, 244Hz, 60Hz, 122Hz, 30Hz] + * 20MHz MCUs: [78.1KHz, 39.2KHz (default), 9.77KHz, 4.9KHz, 2.44KHz, 1.22KHz, 610Hz, 305Hz, 153Hz, 76Hz, 38Hz] + * A greater range can be achieved by enabling USE_OCR2A_AS_TOP. But note that this option blocks the use of + * PWM on pin OC2A. Only use this option if you don't need PWM on 0C2A. (Check your schematic.) + * USE_OCR2A_AS_TOP sacrifices duty cycle control resolution to achieve this broader range of frequencies. + */ +#if ENABLED(FAST_PWM_FAN) + //#define FAST_PWM_FAN_FREQUENCY 31400 + //#define USE_OCR2A_AS_TOP +#endif + +// @section extruder + +/** + * Extruder cooling fans + * + * Extruder auto fans automatically turn on when their extruders' + * temperatures go above EXTRUDER_AUTO_FAN_TEMPERATURE. + * + * Your board's pins file specifies the recommended pins. Override those here + * or set to -1 to disable completely. + * + * Multiple extruders can be assigned to the same pin in which case + * the fan will turn on when any selected extruder is above the threshold. + */ +#define E0_AUTO_FAN_PIN -1 +#define E1_AUTO_FAN_PIN -1 +#define E2_AUTO_FAN_PIN -1 +#define E3_AUTO_FAN_PIN -1 +#define E4_AUTO_FAN_PIN -1 +#define E5_AUTO_FAN_PIN -1 +#define CHAMBER_AUTO_FAN_PIN -1 + +#define EXTRUDER_AUTO_FAN_TEMPERATURE 50 +#define EXTRUDER_AUTO_FAN_SPEED 255 // 255 == full speed +#define CHAMBER_AUTO_FAN_TEMPERATURE 30 +#define CHAMBER_AUTO_FAN_SPEED 255 + +/** + * Part-Cooling Fan Multiplexer + * + * This feature allows you to digitally multiplex the fan output. + * The multiplexer is automatically switched at tool-change. + * Set FANMUX[012]_PINs below for up to 2, 4, or 8 multiplexed fans. + */ +#define FANMUX0_PIN -1 +#define FANMUX1_PIN -1 +#define FANMUX2_PIN -1 + +/** + * M355 Case Light on-off / brightness + */ +//#define CASE_LIGHT_ENABLE +#if ENABLED(CASE_LIGHT_ENABLE) + //#define CASE_LIGHT_PIN 4 // Override the default pin if needed + #define INVERT_CASE_LIGHT false // Set true if Case Light is ON when pin is LOW + #define CASE_LIGHT_DEFAULT_ON true // Set default power-up state on + #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105 // Set default power-up brightness (0-255, requires PWM pin) + //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu + //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. + //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) + #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } + #endif +#endif + +// @section homing + +// If you want endstops to stay on (by default) even when not homing +// enable this option. Override at any time with M120, M121. +//#define ENDSTOPS_ALWAYS_ON_DEFAULT + +// @section extras + +//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats. + +// Employ an external closed loop controller. Override pins here if needed. +//#define EXTERNAL_CLOSED_LOOP_CONTROLLER +#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER) + //#define CLOSED_LOOP_ENABLE_PIN -1 + //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1 +#endif + +/** + * Dual Steppers / Dual Endstops + * + * This section will allow you to use extra E drivers to drive a second motor for X, Y, or Z axes. + * + * For example, set X_DUAL_STEPPER_DRIVERS setting to use a second motor. If the motors need to + * spin in opposite directions set INVERT_X2_VS_X_DIR. If the second motor needs its own endstop + * set X_DUAL_ENDSTOPS. This can adjust for "racking." Use X2_USE_ENDSTOP to set the endstop plug + * that should be used for the second endstop. Extra endstops will appear in the output of 'M119'. + * + * Use X_DUAL_ENDSTOP_ADJUSTMENT to adjust for mechanical imperfection. After homing both motors + * this offset is applied to the X2 motor. To find the offset home the X axis, and measure the error + * in X2. Dual endstop offsets can be set at runtime with 'M666 X Y Z'. + */ + +//#define X_DUAL_STEPPER_DRIVERS +#if ENABLED(X_DUAL_STEPPER_DRIVERS) + #define INVERT_X2_VS_X_DIR true // Set 'true' if X motors should rotate in opposite directions + //#define X_DUAL_ENDSTOPS + #if ENABLED(X_DUAL_ENDSTOPS) + #define X2_USE_ENDSTOP _XMAX_ + #define X_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Y_DUAL_STEPPER_DRIVERS +#if ENABLED(Y_DUAL_STEPPER_DRIVERS) + #define INVERT_Y2_VS_Y_DIR true // Set 'true' if Y motors should rotate in opposite directions + //#define Y_DUAL_ENDSTOPS + #if ENABLED(Y_DUAL_ENDSTOPS) + #define Y2_USE_ENDSTOP _YMAX_ + #define Y_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Z_DUAL_STEPPER_DRIVERS +#if ENABLED(Z_DUAL_STEPPER_DRIVERS) + //#define Z_DUAL_ENDSTOPS + #if ENABLED(Z_DUAL_ENDSTOPS) + #define Z2_USE_ENDSTOP _XMAX_ + #define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Z_TRIPLE_STEPPER_DRIVERS +#if ENABLED(Z_TRIPLE_STEPPER_DRIVERS) + //#define Z_TRIPLE_ENDSTOPS + #if ENABLED(Z_TRIPLE_ENDSTOPS) + #define Z2_USE_ENDSTOP _XMAX_ + #define Z3_USE_ENDSTOP _YMAX_ + #define Z_TRIPLE_ENDSTOPS_ADJUSTMENT2 0 + #define Z_TRIPLE_ENDSTOPS_ADJUSTMENT3 0 + #endif +#endif + +/** + * Dual X Carriage + * + * This setup has two X carriages that can move independently, each with its own hotend. + * The carriages can be used to print an object with two colors or materials, or in + * "duplication mode" it can print two identical or X-mirrored objects simultaneously. + * The inactive carriage is parked automatically to prevent oozing. + * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. + * By default the X2 stepper is assigned to the first unused E plug on the board. + * + * The following Dual X Carriage modes can be selected with M605 S: + * + * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel + * results as long as it supports dual X-carriages. (M605 S0) + * + * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so + * that additional slicer support is not required. (M605 S1) + * + * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with + * the first X-carriage and extruder, to print 2 copies of the same object at the same time. + * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and + * follow with M605 S2 to initiate duplicated movement. + * + * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates + * the movement of the first except the second extruder is reversed in the X axis. + * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and + * follow with M605 S3 to initiate mirrored movement. + */ +//#define DUAL_X_CARRIAGE +#if ENABLED(DUAL_X_CARRIAGE) + #define X1_MIN_POS X_MIN_POS // Set to X_MIN_POS + #define X1_MAX_POS X_BED_SIZE // Set a maximum so the first X-carriage can't hit the parked second X-carriage + #define X2_MIN_POS 80 // Set a minimum to ensure the second X-carriage can't hit the parked first X-carriage + #define X2_MAX_POS 353 // Set this to the distance between toolheads when both heads are homed + #define X2_HOME_DIR 1 // Set to 1. The second X-carriage always homes to the maximum endstop position + #define X2_HOME_POS X2_MAX_POS // Default X2 home position. Set to X2_MAX_POS. + // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software + // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops + // without modifying the firmware (through the "M218 T1 X???" command). + // Remember: you should set the second extruder x-offset to 0 in your slicer. + + // This is the default power-up mode which can be later using M605. + #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_AUTO_PARK_MODE + + // Default x offset in duplication mode (typically set to half print bed width) + #define DEFAULT_DUPLICATION_X_OFFSET 100 + +#endif // DUAL_X_CARRIAGE + +// Activate a solenoid on the active extruder with M380. Disable all with M381. +// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid. +//#define EXT_SOLENOID + +// @section homing + +// Homing hits each endstop, retracts by these distances, then does a slower bump. +#define X_HOME_BUMP_MM 5 +#define Y_HOME_BUMP_MM 5 +#define Z_HOME_BUMP_MM 2 +#define HOMING_BUMP_DIVISOR { 2, 2, 4 } // Re-Bump Speed Divisor (Divides the Homing Feedrate) +//#define QUICK_HOME // If homing includes X and Y, do a diagonal move initially +//#define HOMING_BACKOFF_MM { 2, 2, 2 } // (mm) Move away from the endstops after homing + +// When G28 is called, this option will make Y home before X +//#define HOME_Y_BEFORE_X + +// Enable this if X or Y can't home without homing the other axis first. +//#define CODEPENDENT_XY_HOMING + +#if ENABLED(BLTOUCH) + /** + * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES + * Do not activate settings that the probe might not understand. Clones might misunderstand + * advanced commands. + * + * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then + * check the wiring of the BROWN, RED and ORANGE wires. + * + * Note: If the trigger signal of your probe is not being recognized, it has been very often + * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable" + * like they would be with a real switch. So please check the wiring first. + * + * Settings for all BLTouch and clone probes: + */ + + // Safety: The probe needs time to recognize the command. + // Minimum command delay (ms). Enable and increase if needed. + //#define BLTOUCH_DELAY 500 + + /** + * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones: + */ + + // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful + // in special cases, like noisy or filtered input configurations. + //#define BLTOUCH_FORCE_SW_MODE + + /** + * Settings for BLTouch Smart 3.0 and 3.1 + * Summary: + * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes + * - High-Speed mode + * - Disable LCD voltage options + */ + + /** + * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller! + * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup. + * If disabled, OD mode is the hard-coded default on 3.0 + * On startup, Marlin will compare its eeprom to this vale. If the selected mode + * differs, a mode set eeprom write will be completed at initialization. + * Use the option below to force an eeprom write to a V3.1 probe regardless. + */ + //#define BLTOUCH_SET_5V_MODE + + /** + * Safety: Activate if connecting a probe with an unknown voltage mode. + * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0 + * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write ) + * To preserve the life of the probe, use this once then turn it off and re-flash. + */ + //#define BLTOUCH_FORCE_MODE_SET + + /** + * Use "HIGH SPEED" mode for probing. + * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems. + * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function + * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state. + */ + //#define BLTOUCH_HS_MODE + + // Safety: Enable voltage mode settings in the LCD menu. + //#define BLTOUCH_LCD_VOLTAGE_MENU + +#endif // BLTOUCH + +/** + * Z Steppers Auto-Alignment + * Add the G34 command to align multiple Z steppers using a bed probe. + */ +//#define Z_STEPPER_AUTO_ALIGN +#if ENABLED(Z_STEPPER_AUTO_ALIGN) + // Define probe X and Y positions for Z1, Z2 [, Z3] + #define Z_STEPPER_ALIGN_X { 10, 150, 290 } + #define Z_STEPPER_ALIGN_Y { 290, 10, 290 } + // Set number of iterations to align + #define Z_STEPPER_ALIGN_ITERATIONS 3 + // Enable to restore leveling setup after operation + #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + + // Use the amplification factor to de-/increase correction step. + // In case the stepper (spindle) position is further out than the test point + // Use a value > 1. NOTE: This may cause instability + #define Z_STEPPER_ALIGN_AMP 1.0 + // Stop criterion. If the accuracy is better than this stop iterating early + #define Z_STEPPER_ALIGN_ACC 0.02 +#endif + +// @section machine + +#define AXIS_RELATIVE_MODES { false, false, false, false } + +// Add a Duplicate option for well-separated conjoined nozzles +//#define MULTI_NOZZLE_DUPLICATION + +// By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step. +#define INVERT_X_STEP_PIN false +#define INVERT_Y_STEP_PIN false +#define INVERT_Z_STEP_PIN false +#define INVERT_E_STEP_PIN false + +// Default stepper release if idle. Set to 0 to deactivate. +// Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true. +// Time can be set by M18 and M84. +#define DEFAULT_STEPPER_DEACTIVE_TIME 120 +#define DISABLE_INACTIVE_X true +#define DISABLE_INACTIVE_Y true +#define DISABLE_INACTIVE_Z true // Set to false if the nozzle will fall down on your printed part when print has finished. +#define DISABLE_INACTIVE_E true + +#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate +#define DEFAULT_MINTRAVELFEEDRATE 0.0 + +//#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated + +// @section lcd + +#if EITHER(ULTIPANEL, EXTENSIBLE_UI) + #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #if ENABLED(ULTIPANEL) + #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" + #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen + #endif +#endif + +// @section extras + +// minimum time in microseconds that a movement needs to take if the buffer is emptied. +#define DEFAULT_MINSEGMENTTIME 20000 + +// If defined the movements slow down when the look ahead buffer is only half full +#define SLOWDOWN + +// Frequency limit +// See nophead's blog for more info +// Not working O +//#define XY_FREQUENCY_LIMIT 15 + +// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end +// of the buffer and all stops. This should not be much greater than zero and should only be changed +// if unwanted behavior is observed on a user's machine when running at very slow speeds. +#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s) + +// +// Backlash Compensation +// Adds extra movement to axes on direction-changes to account for backlash. +// +//#define BACKLASH_COMPENSATION +#if ENABLED(BACKLASH_COMPENSATION) + // Define values for backlash distance and correction. + // If BACKLASH_GCODE is enabled these values are the defaults. + #define BACKLASH_DISTANCE_MM { 0, 0, 0 } // (mm) + #define BACKLASH_CORRECTION 0.0 // 0.0 = no correction; 1.0 = full correction + + // Set BACKLASH_SMOOTHING_MM to spread backlash correction over multiple segments + // to reduce print artifacts. (Enabling this is costly in memory and computation!) + //#define BACKLASH_SMOOTHING_MM 3 // (mm) + + // Add runtime configuration and tuning of backlash values (M425) + //#define BACKLASH_GCODE + + #if ENABLED(BACKLASH_GCODE) + // Measure the Z backlash when probing (G29) and set with "M425 Z" + #define MEASURE_BACKLASH_WHEN_PROBING + + #if ENABLED(MEASURE_BACKLASH_WHEN_PROBING) + // When measuring, the probe will move up to BACKLASH_MEASUREMENT_LIMIT + // mm away from point of contact in BACKLASH_MEASUREMENT_RESOLUTION + // increments while checking for the contact to be broken. + #define BACKLASH_MEASUREMENT_LIMIT 0.5 // (mm) + #define BACKLASH_MEASUREMENT_RESOLUTION 0.005 // (mm) + #define BACKLASH_MEASUREMENT_FEEDRATE Z_PROBE_SPEED_SLOW // (mm/m) + #endif + #endif +#endif + +/** + * Automatic backlash, position and hotend offset calibration + * + * Enable G425 to run automatic calibration using an electrically- + * conductive cube, bolt, or washer mounted on the bed. + * + * G425 uses the probe to touch the top and sides of the calibration object + * on the bed and measures and/or correct positional offsets, axis backlash + * and hotend offsets. + * + * Note: HOTEND_OFFSET and CALIBRATION_OBJECT_CENTER must be set to within + * ±5mm of true values for G425 to succeed. + */ +//#define CALIBRATION_GCODE +#if ENABLED(CALIBRATION_GCODE) + + #define CALIBRATION_MEASUREMENT_RESOLUTION 0.01 // mm + + #define CALIBRATION_FEEDRATE_SLOW 60 // mm/m + #define CALIBRATION_FEEDRATE_FAST 1200 // mm/m + #define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/m + + // The following parameters refer to the conical section of the nozzle tip. + #define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm + #define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm + + // Uncomment to enable reporting (required for "G425 V", but consumes PROGMEM). + //#define CALIBRATION_REPORTING + + // The true location and dimension the cube/bolt/washer on the bed. + #define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0} // mm + #define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0} // mm + + // Comment out any sides which are unreachable by the probe. For best + // auto-calibration results, all sides must be reachable. + #define CALIBRATION_MEASURE_RIGHT + #define CALIBRATION_MEASURE_FRONT + #define CALIBRATION_MEASURE_LEFT + #define CALIBRATION_MEASURE_BACK + + // Probing at the exact top center only works if the center is flat. If + // probing on a screwhead or hollow washer, probe near the edges. + //#define CALIBRATION_MEASURE_AT_TOP_EDGES + + // Define pin which is read during calibration + #ifndef CALIBRATION_PIN + #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop + #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin + //#define CALIBRATION_PIN_PULLDOWN + #define CALIBRATION_PIN_PULLUP + #endif +#endif + +/** + * Adaptive Step Smoothing increases the resolution of multi-axis moves, particularly at step frequencies + * below 1kHz (for AVR) or 10kHz (for ARM), where aliasing between axes in multi-axis moves causes audible + * vibration and surface artifacts. The algorithm adapts to provide the best possible step smoothing at the + * lowest stepping frequencies. + */ +//#define ADAPTIVE_STEP_SMOOTHING + +/** + * Custom Microstepping + * Override as-needed for your setup. Up to 3 MS pins are supported. + */ +//#define MICROSTEP1 LOW,LOW,LOW +//#define MICROSTEP2 HIGH,LOW,LOW +//#define MICROSTEP4 LOW,HIGH,LOW +//#define MICROSTEP8 HIGH,HIGH,LOW +//#define MICROSTEP16 LOW,LOW,HIGH +//#define MICROSTEP32 HIGH,LOW,HIGH + +// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU. +#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16] + +/** + * @section stepper motor current + * + * Some boards have a means of setting the stepper motor current via firmware. + * + * The power on motor currents are set by: + * PWM_MOTOR_CURRENT - used by MINIRAMBO & ULTIMAIN_2 + * known compatible chips: A4982 + * DIGIPOT_MOTOR_CURRENT - used by BQ_ZUM_MEGA_3D, RAMBO & SCOOVO_X9H + * known compatible chips: AD5206 + * DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2 + * known compatible chips: MCP4728 + * DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, AZTEEG_X5_MINI_WIFI, MIGHTYBOARD_REVE + * known compatible chips: MCP4451, MCP4018 + * + * Motor currents can also be set by M907 - M910 and by the LCD. + * M907 - applies to all. + * M908 - BQ_ZUM_MEGA_3D, RAMBO, PRINTRBOARD_REVF, RIGIDBOARD_V2 & SCOOVO_X9H + * M909, M910 & LCD - only PRINTRBOARD_REVF & RIGIDBOARD_V2 + */ +//#define PWM_MOTOR_CURRENT { 1300, 1300, 1250 } // Values in milliamps +//#define DIGIPOT_MOTOR_CURRENT { 135,135,135,135,135 } // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A) +//#define DAC_MOTOR_CURRENT_DEFAULT { 70, 80, 90, 80 } // Default drive percent - X, Y, Z, E axis + +// Use an I2C based DIGIPOT (e.g., Azteeg X3 Pro) +//#define DIGIPOT_I2C +#if ENABLED(DIGIPOT_I2C) && !defined(DIGIPOT_I2C_ADDRESS_A) + /** + * Common slave addresses: + * + * A (A shifted) B (B shifted) IC + * Smoothie 0x2C (0x58) 0x2D (0x5A) MCP4451 + * AZTEEG_X3_PRO 0x2C (0x58) 0x2E (0x5C) MCP4451 + * AZTEEG_X5_MINI 0x2C (0x58) 0x2E (0x5C) MCP4451 + * AZTEEG_X5_MINI_WIFI 0x58 0x5C MCP4451 + * MIGHTYBOARD_REVE 0x2F (0x5E) MCP4018 + */ + #define DIGIPOT_I2C_ADDRESS_A 0x2C // unshifted slave address for first DIGIPOT + #define DIGIPOT_I2C_ADDRESS_B 0x2D // unshifted slave address for second DIGIPOT +#endif + +//#define DIGIPOT_MCP4018 // Requires library from https://github.com/stawel/SlowSoftI2CMaster +#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8 MKS SBASE: 5 +// Actual motor currents in Amps. The number of entries must match DIGIPOT_I2C_NUM_CHANNELS. +// These correspond to the physical drivers, so be mindful if the order is changed. +#define DIGIPOT_I2C_MOTOR_CURRENTS { 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0 } // AZTEEG_X3_PRO + +//=========================================================================== +//=============================Additional Features=========================== +//=========================================================================== + +// @section lcd + +// Change values more rapidly when the encoder is rotated faster +#define ENCODER_RATE_MULTIPLIER +#if ENABLED(ENCODER_RATE_MULTIPLIER) + #define ENCODER_10X_STEPS_PER_SEC 30 // (steps/s) Encoder rate for 10x speed + #define ENCODER_100X_STEPS_PER_SEC 80 // (steps/s) Encoder rate for 100x speed +#endif + +// Play a beep when the feedrate is changed from the Status Screen +//#define BEEP_ON_FEEDRATE_CHANGE +#if ENABLED(BEEP_ON_FEEDRATE_CHANGE) + #define FEEDRATE_CHANGE_BEEP_DURATION 10 + #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 +#endif + +// Include a page of printer information in the LCD Main Menu +//#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif + +// Scroll a longer status message into view +//#define STATUS_MESSAGE_SCROLLING + +// On the Info Screen, display XY with one decimal place when possible +//#define LCD_DECIMAL_SMALL_XY + +// The timeout (in ms) to return to the status screen from sub-menus +//#define LCD_TIMEOUT_TO_STATUS 15000 + +// Add an 'M73' G-code to set the current percentage +//#define LCD_SET_PROGRESS_MANUALLY + +#if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS + //#define LCD_PROGRESS_BAR // Show a progress bar on HD44780 LCDs for SD printing + #if ENABLED(LCD_PROGRESS_BAR) + #define PROGRESS_BAR_BAR_TIME 2000 // (ms) Amount of time to show the bar + #define PROGRESS_BAR_MSG_TIME 3000 // (ms) Amount of time to show the status message + #define PROGRESS_MSG_EXPIRE 0 // (ms) Amount of time to retain the status message (0=forever) + //#define PROGRESS_MSG_ONCE // Show the message for MSG_TIME then clear it + //#define LCD_PROGRESS_BAR_TEST // Add a menu item to test the progress bar + #endif +#endif + +/** + * LED Control Menu + * Enable this feature to add LED Control to the LCD menu + */ +//#define LED_CONTROL_MENU +#if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + #define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif +#endif // LED_CONTROL_MENU + +#if ENABLED(SDSUPPORT) + + // Some RAMPS and other boards don't detect when an SD card is inserted. You can work + // around this by connecting a push button or single throw switch to the pin defined + // as SD_DETECT_PIN in your board's pins definitions. + // This setting should be disabled unless you are using a push button, pulling the pin to ground. + // Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER). + #define SD_DETECT_INVERTED + + #define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished + #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place. + + // Reverse SD sort to show "more recent" files first, according to the card's FAT. + // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended. + //#define SDCARD_RATHERRECENTFIRST + + #define SD_MENU_CONFIRM_START // Confirm the selected SD file before printing + + //#define MENU_ADDAUTOSTART // Add a menu option to run auto#.g files + + #define EVENT_GCODE_SD_STOP "M21" // G-code to run on Stop Print (e.g., "G28XY" or "G27") + + /** + * Continue after Power-Loss (Creality3D) + * + * Store the current state to the SD Card at the start of each layer + * during SD printing. If the recovery file is found at boot time, present + * an option on the LCD screen to continue the print from the last-known + * point in the file. + */ + //#define POWER_LOSS_RECOVERY + #if ENABLED(POWER_LOSS_RECOVERY) + //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume + //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. + + // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, + // especially with "vase mode" printing. Set too high and vases cannot be continued. + #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + #endif + + /** + * Sort SD file listings in alphabetical order. + * + * With this option enabled, items on SD cards will be sorted + * by name for easier navigation. + * + * By default... + * + * - Use the slowest -but safest- method for sorting. + * - Folders are sorted to the top. + * - The sort key is statically allocated. + * - No added G-code (M34) support. + * - 40 item sorting limit. (Items after the first 40 are unsorted.) + * + * SD sorting uses static allocation (as set by SDSORT_LIMIT), allowing the + * compiler to calculate the worst-case usage and throw an error if the SRAM + * limit is exceeded. + * + * - SDSORT_USES_RAM provides faster sorting via a static directory buffer. + * - SDSORT_USES_STACK does the same, but uses a local stack-based buffer. + * - SDSORT_CACHE_NAMES will retain the sorted file listing in RAM. (Expensive!) + * - SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible. (Use with caution!) + */ + //#define SDCARD_SORT_ALPHA + + // SD Card Sorting options + #if ENABLED(SDCARD_SORT_ALPHA) + #define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). Costs 27 bytes each. + #define FOLDER_SORTING -1 // -1=above 0=none 1=below + #define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 g-code. + #define SDSORT_USES_RAM true // Pre-allocate a static array for faster pre-sorting. + #define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.) + #define SDSORT_CACHE_NAMES true // Keep sorted items in RAM longer for speedy performance. Most expensive option. + #define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use! + #define SDSORT_CACHE_VFATS 2 // Maximum number of 13-byte VFAT entries to use for sorting. + // Note: Only affects SCROLL_LONG_FILENAMES with SDSORT_CACHE_NAMES but not SDSORT_DYNAMIC_RAM. + #endif + + // This allows hosts to request long names for files and folders with M33 + //#define LONG_FILENAME_HOST_SUPPORT + + // Enable this option to scroll long filenames in the SD card menu + //#define SCROLL_LONG_FILENAMES + + // Leave the heaters on after Stop Print (not recommended!) + //#define SD_ABORT_NO_COOLDOWN + + /** + * This option allows you to abort SD printing when any endstop is triggered. + * This feature must be enabled with "M540 S1" or from the LCD menu. + * To have any effect, endstops must be enabled during SD printing. + */ + //#define SD_ABORT_ON_ENDSTOP_HIT + + /** + * This option makes it easier to print the same SD Card file again. + * On print completion the LCD Menu will open with the file selected. + * You can just click to start the print, or navigate elsewhere. + */ + //#define SD_REPRINT_LAST_SELECTED_FILE + + /** + * Auto-report SdCard status with M27 S + */ + //#define AUTO_REPORT_SD_STATUS + + /** + * Support for USB thumb drives using an Arduino USB Host Shield or + * equivalent MAX3421E breakout board. The USB thumb drive will appear + * to Marlin as an SD card. + * + * The MAX3421E must be assigned the same pins as the SD card reader, with + * the following pin mapping: + * + * SCLK, MOSI, MISO --> SCLK, MOSI, MISO + * INT --> SD_DETECT_PIN + * SS --> SDSS + */ + //#define USB_FLASH_DRIVE_SUPPORT + #if ENABLED(USB_FLASH_DRIVE_SUPPORT) + #define USB_CS_PIN SDSS + #define USB_INTR_PIN SD_DETECT_PIN + #endif + + /** + * When using a bootloader that supports SD-Firmware-Flashing, + * add a menu item to activate SD-FW-Update on the next reboot. + * + * Requires ATMEGA2560 (Arduino Mega) + * + * Tested with this bootloader: + * https://github.com/FleetProbe/MicroBridge-Arduino-ATMega2560 + */ + //#define SD_FIRMWARE_UPDATE + #if ENABLED(SD_FIRMWARE_UPDATE) + #define SD_FIRMWARE_UPDATE_EEPROM_ADDR 0x1FF + #define SD_FIRMWARE_UPDATE_ACTIVE_VALUE 0xF0 + #define SD_FIRMWARE_UPDATE_INACTIVE_VALUE 0xFF + #endif + + // Add an optimized binary file transfer mode, initiated with 'M28 B1' + //#define BINARY_FILE_TRANSFER + + #if HAS_SDCARD_CONNECTION + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD + #endif + +#endif // SDSUPPORT + +/** + * By default an onboard SD card reader may be shared as a USB mass- + * storage device. This option hides the SD card from the host PC. + */ +//#define NO_SD_HOST_DRIVE // Disable SD Card access over USB (for security). + +/** + * Additional options for Graphical Displays + * + * Use the optimizations here to improve printing performance, + * which can be adversely affected by graphical display drawing, + * especially when doing several short moves, and when printing + * on DELTA and SCARA machines. + * + * Some of these options may result in the display lagging behind + * controller events, as there is a trade-off between reliable + * printing performance versus fast display updates. + */ +#if HAS_GRAPHICAL_LCD + // Show SD percentage next to the progress bar + //#define DOGM_SD_PERCENT + + // Enable to save many cycles by drawing a hollow frame on the Info Screen + #define XYZ_HOLLOW_FRAME + + // Enable to save many cycles by drawing a hollow frame on Menu Screens + #define MENU_HOLLOW_FRAME + + // A bigger font is available for edit items. Costs 3120 bytes of PROGMEM. + // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. + //#define USE_BIG_EDIT_FONT + + // A smaller font may be used on the Info Screen. Costs 2300 bytes of PROGMEM. + // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. + //#define USE_SMALL_INFOFONT + + // Enable this option and reduce the value to optimize screen updates. + // The normal delay is 10µs. Use the lowest value that still gives a reliable display. + //#define DOGM_SPI_DELAY_US 5 + + // Swap the CW/CCW indicators in the graphics overlay + //#define OVERLAY_GFX_REVERSE + + /** + * ST7920-based LCDs can emulate a 16 x 4 character display using + * the ST7920 character-generator for very fast screen updates. + * Enable LIGHTWEIGHT_UI to use this special display mode. + * + * Since LIGHTWEIGHT_UI has limited space, the position and status + * message occupy the same line. Set STATUS_EXPIRE_SECONDS to the + * length of time to display the status message before clearing. + * + * Set STATUS_EXPIRE_SECONDS to zero to never clear the status. + * This will prevent position updates from being displayed. + */ + #if ENABLED(U8GLIB_ST7920) + //#define LIGHTWEIGHT_UI + #if ENABLED(LIGHTWEIGHT_UI) + #define STATUS_EXPIRE_SECONDS 20 + #endif + #endif + + /** + * Status (Info) Screen customizations + * These options may affect code size and screen render time. + * Custom status screens can forcibly override these settings. + */ + //#define STATUS_COMBINE_HEATERS // Use combined heater images instead of separate ones + //#define STATUS_HOTEND_NUMBERLESS // Use plain hotend icons instead of numbered ones (with 2+ hotends) + #define STATUS_HOTEND_INVERTED // Show solid nozzle bitmaps when heating (Requires STATUS_HOTEND_ANIM) + #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating + #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating + #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap + //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap + //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames + //#define STATUS_HEAT_PERCENT // Show heating in a progress bar + //#define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash) + + // Frivolous Game Options + //#define MARLIN_BRICKOUT + //#define MARLIN_INVADERS + //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu + +#endif // HAS_GRAPHICAL_LCD + +// @section safety + +/** + * The watchdog hardware timer will do a reset and disable all outputs + * if the firmware gets too overloaded to read the temperature sensors. + * + * If you find that watchdog reboot causes your AVR board to hang forever, + * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO. + * NOTE: This method is less reliable as it can only catch hangups while + * interrupts are enabled. + */ +#define USE_WATCHDOG +#if ENABLED(USE_WATCHDOG) + //#define WATCHDOG_RESET_MANUAL +#endif + +// @section lcd + +/** + * Babystepping enables movement of the axes by tiny increments without changing + * the current position values. This feature is used primarily to adjust the Z + * axis in the first layer of a print in real-time. + * + * Warning: Does not respect endstops! + */ +//#define BABYSTEPPING +#if ENABLED(BABYSTEPPING) + //#define BABYSTEP_WITHOUT_HOMING + //#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA! + #define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way + #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion. + + //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping. + #if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING) + #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds. + // Note: Extra time may be added to mitigate controller latency. + //#define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement). + //#define MOVE_Z_WHEN_IDLE // Jump to the move Z menu on doubleclick when printer is idle. + #if ENABLED(MOVE_Z_WHEN_IDLE) + #define MOVE_Z_IDLE_MULTIPLICATOR 1 // Multiply 1mm by this factor for the move step size. + #endif + #endif + + //#define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28 + + //#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping + #if ENABLED(BABYSTEP_ZPROBE_OFFSET) + //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets + //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor + #endif +#endif + +// @section extruder + +/** + * Linear Pressure Control v1.5 + * + * Assumption: advance [steps] = k * (delta velocity [steps/s]) + * K=0 means advance disabled. + * + * NOTE: K values for LIN_ADVANCE 1.5 differ from earlier versions! + * + * Set K around 0.22 for 3mm PLA Direct Drive with ~6.5cm between the drive gear and heatbreak. + * Larger K values will be needed for flexible filament and greater distances. + * If this algorithm produces a higher speed offset than the extruder can handle (compared to E jerk) + * print acceleration will be reduced during the affected moves to keep within the limit. + * + * See http://marlinfw.org/docs/features/lin_advance.html for full instructions. + * Mention @Sebastianv650 on GitHub to alert the author of any issues. + */ +//#define LIN_ADVANCE +#if ENABLED(LIN_ADVANCE) + //#define EXTRA_LIN_ADVANCE_K // Enable for second linear advance constants + #define LIN_ADVANCE_K 0.22 // Unit: mm compression per 1mm/s extruder speed + //#define LA_DEBUG // If enabled, this will generate debug information output over USB. +#endif + +// @section leveling + +#if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL) + // Override the mesh area if the automatic (max) area is too large + //#define MESH_MIN_X MESH_INSET + //#define MESH_MIN_Y MESH_INSET + //#define MESH_MAX_X X_BED_SIZE - (MESH_INSET) + //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET) +#endif + +/** + * Repeatedly attempt G29 leveling until it succeeds. + * Stop after G29_MAX_RETRIES attempts. + */ +//#define G29_RETRY_AND_RECOVER +#if ENABLED(G29_RETRY_AND_RECOVER) + #define G29_MAX_RETRIES 3 + #define G29_HALT_ON_FAILURE + /** + * Specify the GCODE commands that will be executed when leveling succeeds, + * between attempts, and after the maximum number of retries have been tried. + */ + #define G29_SUCCESS_COMMANDS "M117 Bed leveling done." + #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0" + #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1" + +#endif + +// @section extras + +// +// G2/G3 Arc Support +// +#define ARC_SUPPORT // Disable this feature to save ~3226 bytes +#if ENABLED(ARC_SUPPORT) + #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles + //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes +#endif + +// Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes. +//#define BEZIER_CURVE_SUPPORT + +/** + * G38 Probe Target + * + * This option adds G38.2 and G38.3 (probe towards target) + * and optionally G38.4 and G38.5 (probe away from target). + * Set MULTIPLE_PROBING for G38 to probe more than once. + */ +//#define G38_PROBE_TARGET +#if ENABLED(G38_PROBE_TARGET) + //#define G38_PROBE_AWAY // Include G38.4 and G38.5 to probe away from target + #define G38_MINIMUM_MOVE 0.0275 // (mm) Minimum distance that will produce a move. +#endif + +// Moves (or segments) with fewer steps than this will be joined with the next move +#define MIN_STEPS_PER_SEGMENT 6 + +/** + * Minimum delay after setting the stepper DIR (in ns) + * 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire) + * 20 : Minimum for TMC2xxx drivers + * 200 : Minimum for A4988 drivers + * 400 : Minimum for A5984 drivers + * 500 : Minimum for LV8729 drivers (guess, no info in datasheet) + * 650 : Minimum for DRV8825 drivers + * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet) + * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet) + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MINIMUM_STEPPER_DIR_DELAY 650 + +/** + * Minimum stepper driver pulse width (in µs) + * 0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers + * 0 : Minimum 500ns for LV8729, adjusted in stepper.h + * 1 : Minimum for A4988 and A5984 stepper drivers + * 2 : Minimum for DRV8825 stepper drivers + * 3 : Minimum for TB6600 stepper drivers + * 30 : Minimum for TB6560 stepper drivers + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MINIMUM_STEPPER_PULSE 2 + +/** + * Maximum stepping rate (in Hz) the stepper driver allows + * If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE) + * 500000 : Maximum for A4988 stepper driver + * 400000 : Maximum for TMC2xxx stepper drivers + * 250000 : Maximum for DRV8825 stepper driver + * 200000 : Maximum for LV8729 stepper driver + * 150000 : Maximum for TB6600 stepper driver + * 15000 : Maximum for TB6560 stepper driver + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MAXIMUM_STEPPER_RATE 250000 + +// @section temperature + +// Control heater 0 and heater 1 in parallel. +//#define HEATERS_PARALLEL + +//=========================================================================== +//================================= Buffers ================================= +//=========================================================================== + +// @section hidden + +// The number of linear motions that can be in the plan at any give time. +// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2 (e.g. 8, 16, 32) because shifts and ors are used to do the ring-buffering. +#if ENABLED(SDSUPPORT) + #define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller +#else + #define BLOCK_BUFFER_SIZE 16 // maximize block buffer +#endif + +// @section serial + +// The ASCII buffer for serial input +#define MAX_CMD_SIZE 96 +#define BUFSIZE 4 + +// Transmission to Host Buffer Size +// To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0. +// To buffer a simple "ok" you need 4 bytes. +// For ADVANCED_OK (M105) you need 32 bytes. +// For debug-echo: 128 bytes for the optimal speed. +// Other output doesn't need to be that speedy. +// :[0, 2, 4, 8, 16, 32, 64, 128, 256] +#define TX_BUFFER_SIZE 0 + +// Host Receive Buffer Size +// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough. +// To use flow control, set this buffer size to at least 1024 bytes. +// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048] +//#define RX_BUFFER_SIZE 1024 + +#if RX_BUFFER_SIZE >= 1024 + // Enable to have the controller send XON/XOFF control characters to + // the host to signal the RX buffer is becoming full. + //#define SERIAL_XON_XOFF +#endif + +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + +#if ENABLED(SDSUPPORT) + // Enable this option to collect and display the maximum + // RX queue usage after transferring a file to SD. + //#define SERIAL_STATS_MAX_RX_QUEUED + + // Enable this option to collect and display the number + // of dropped bytes after a file transfer to SD. + //#define SERIAL_STATS_DROPPED_RX +#endif + +// Enable an emergency-command parser to intercept certain commands as they +// enter the serial receive buffer, so they cannot be blocked. +// Currently handles M108, M112, M410 +// Does not work on boards using AT90USB (USBCON) processors! +//#define EMERGENCY_PARSER + +// Bad Serial-connections can miss a received command by sending an 'ok' +// Therefore some clients abort after 30 seconds in a timeout. +// Some other clients start sending commands while receiving a 'wait'. +// This "wait" is only sent when the buffer is empty. 1 second is a good value here. +//#define NO_TIMEOUTS 1000 // Milliseconds + +// Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary. +//#define ADVANCED_OK + +// Printrun may have trouble receiving long strings all at once. +// This option inserts short delays between lines of serial output. +#define SERIAL_OVERRUN_PROTECTION + +// @section extras + +/** + * Extra Fan Speed + * Adds a secondary fan speed for each print-cooling fan. + * 'M106 P T3-255' : Set a secondary speed for + * 'M106 P T2' : Use the set secondary speed + * 'M106 P T1' : Restore the previous fan speed + */ +//#define EXTRA_FAN_SPEED + +/** + * Firmware-based and LCD-controlled retract + * + * Add G10 / G11 commands for automatic firmware-based retract / recover. + * Use M207 and M208 to define parameters for retract / recover. + * + * Use M209 to enable or disable auto-retract. + * With auto-retract enabled, all G1 E moves within the set range + * will be converted to firmware-based retract/recover moves. + * + * Be sure to turn off auto-retract during filament change. + * + * Note that M207 / M208 / M209 settings are saved to EEPROM. + * + */ +//#define FWRETRACT +#if ENABLED(FWRETRACT) + #define FWRETRACT_AUTORETRACT // costs ~500 bytes of PROGMEM + #if ENABLED(FWRETRACT_AUTORETRACT) + #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over + #define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion + #endif + #define RETRACT_LENGTH 3 // Default retract length (positive mm) + #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change + #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) + #define RETRACT_ZRAISE 0 // Default retract Z-raise (mm) + #define RETRACT_RECOVER_LENGTH 0 // Default additional recover length (mm, added to retract length when recovering) + #define RETRACT_RECOVER_LENGTH_SWAP 0 // Default additional swap recover length (mm, added to retract length when recovering from extruder change) + #define RETRACT_RECOVER_FEEDRATE 8 // Default feedrate for recovering from retraction (mm/s) + #define RETRACT_RECOVER_FEEDRATE_SWAP 8 // Default feedrate for recovering from swap retraction (mm/s) + #if ENABLED(MIXING_EXTRUDER) + //#define RETRACT_SYNC_MIXING // Retract and restore all mixing steppers simultaneously + #endif +#endif + +/** + * Universal tool change settings. + * Applies to all types of extruders except where explicitly noted. + */ +#if EXTRUDERS > 1 + // Z raise distance for tool-change, as needed for some extruders + #define TOOLCHANGE_ZRAISE 2 // (mm) + //#define TOOLCHANGE_NO_RETURN // Never return to the previous position on tool-change + + // Retract and prime filament on tool-change + //#define TOOLCHANGE_FILAMENT_SWAP + #if ENABLED(TOOLCHANGE_FILAMENT_SWAP) + #define TOOLCHANGE_FIL_SWAP_LENGTH 12 // (mm) + #define TOOLCHANGE_FIL_EXTRA_PRIME 2 // (mm) + #define TOOLCHANGE_FIL_SWAP_RETRACT_SPEED 3600 // (mm/m) + #define TOOLCHANGE_FIL_SWAP_PRIME_SPEED 3600 // (mm/m) + #endif + + /** + * Position to park head during tool change. + * Doesn't apply to SWITCHING_TOOLHEAD, DUAL_X_CARRIAGE, or PARKING_EXTRUDER + */ + //#define TOOLCHANGE_PARK + #if ENABLED(TOOLCHANGE_PARK) + #define TOOLCHANGE_PARK_XY { X_MIN_POS + 10, Y_MIN_POS + 10 } + #define TOOLCHANGE_PARK_XY_FEEDRATE 6000 // (mm/m) + #endif +#endif + +/** + * Advanced Pause + * Experimental feature for filament change support and for parking the nozzle when paused. + * Adds the GCode M600 for initiating filament change. + * If PARK_HEAD_ON_PAUSE enabled, adds the GCode M125 to pause printing and park the nozzle. + * + * Requires an LCD display. + * Requires NOZZLE_PARK_FEATURE. + * This feature is required for the default FILAMENT_RUNOUT_SCRIPT. + */ +//#define ADVANCED_PAUSE_FEATURE +#if ENABLED(ADVANCED_PAUSE_FEATURE) + #define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate. + #define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract. + // This short retract is done immediately, before parking the nozzle. + #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast. + #define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. + #define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload. + // For Bowden, the full length of the tube and nozzle. + // For direct drive, the full length of the nozzle. + // Set to 0 for manual unloading. + #define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load. + #define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material. + // 0 to disable start loading and skip to fast load only + #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast. + #define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. + #define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle. + // For Bowden, the full length of the tube and nozzle. + // For direct drive, the full length of the nozzle. + //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted. + #define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate. + #define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading. + // Set to 0 for manual extrusion. + // Filament can be extruded repeatedly from the Filament Change menu + // until extrusion is consistent, and to purge old filament. + #define ADVANCED_PAUSE_RESUME_PRIME 0 // (mm) Extra distance to prime nozzle after returning from park. + //#define ADVANCED_PAUSE_FANS_PAUSE // Turn off print-cooling fans while the machine is paused. + + // Filament Unload does a Retract, Delay, and Purge first: + #define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length. + #define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract. + #define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged. + + #define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety. + #define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed. + #define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change. + + //#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change. + //#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change + + //#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu. + //#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302) +#endif + +// @section tmc + +/** + * TMC26X Stepper Driver options + * + * The TMC26XStepper library is required for this stepper driver. + * https://github.com/trinamic/TMC26XStepper + */ +#if HAS_DRIVER(TMC26X) + + #if AXIS_DRIVER_TYPE_X(TMC26X) + #define X_MAX_CURRENT 1000 // (mA) + #define X_SENSE_RESISTOR 91 // (mOhms) + #define X_MICROSTEPS 16 // Number of microsteps + #endif + + #if AXIS_DRIVER_TYPE_X2(TMC26X) + #define X2_MAX_CURRENT 1000 + #define X2_SENSE_RESISTOR 91 + #define X2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Y(TMC26X) + #define Y_MAX_CURRENT 1000 + #define Y_SENSE_RESISTOR 91 + #define Y_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Y2(TMC26X) + #define Y2_MAX_CURRENT 1000 + #define Y2_SENSE_RESISTOR 91 + #define Y2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z(TMC26X) + #define Z_MAX_CURRENT 1000 + #define Z_SENSE_RESISTOR 91 + #define Z_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z2(TMC26X) + #define Z2_MAX_CURRENT 1000 + #define Z2_SENSE_RESISTOR 91 + #define Z2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z3(TMC26X) + #define Z3_MAX_CURRENT 1000 + #define Z3_SENSE_RESISTOR 91 + #define Z3_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E0(TMC26X) + #define E0_MAX_CURRENT 1000 + #define E0_SENSE_RESISTOR 91 + #define E0_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E1(TMC26X) + #define E1_MAX_CURRENT 1000 + #define E1_SENSE_RESISTOR 91 + #define E1_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E2(TMC26X) + #define E2_MAX_CURRENT 1000 + #define E2_SENSE_RESISTOR 91 + #define E2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E3(TMC26X) + #define E3_MAX_CURRENT 1000 + #define E3_SENSE_RESISTOR 91 + #define E3_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E4(TMC26X) + #define E4_MAX_CURRENT 1000 + #define E4_SENSE_RESISTOR 91 + #define E4_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E5(TMC26X) + #define E5_MAX_CURRENT 1000 + #define E5_SENSE_RESISTOR 91 + #define E5_MICROSTEPS 16 + #endif + +#endif // TMC26X + +// @section tmc_smart + +/** + * To use TMC2130, TMC2160, TMC2660, TMC5130, TMC5160 stepper drivers in SPI mode + * connect your SPI pins to the hardware SPI interface on your board and define + * the required CS pins in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 + * pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.). + * You may also use software SPI if you wish to use general purpose IO pins. + * + * To use TMC2208 stepper UART-configurable stepper drivers connect #_SERIAL_TX_PIN + * to the driver side PDN_UART pin with a 1K resistor. + * To use the reading capabilities, also connect #_SERIAL_RX_PIN to PDN_UART without + * a resistor. + * The drivers can also be used with hardware serial. + * + * TMCStepper library is required to use TMC stepper drivers. + * https://github.com/teemuatlut/TMCStepper + */ +#if HAS_TRINAMIC + + #define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current + #define INTERPOLATE true // Interpolate X/Y/Z_MICROSTEPS to 256 + + #if AXIS_IS_TMC(X) + #define X_CURRENT 700 // (mA) RMS current. Multiply by 1.414 for peak current. + #define X_MICROSTEPS 16 // 0..256 + #define X_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(X2) + #define X2_CURRENT 800 + #define X2_MICROSTEPS 16 + #define X2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Y) + #define Y_CURRENT 500 + #define Y_MICROSTEPS 16 + #define Y_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Y2) + #define Y2_CURRENT 800 + #define Y2_MICROSTEPS 16 + #define Y2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Z) + #define Z_CURRENT 800 + #define Z_MICROSTEPS 16 + #define Z_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Z2) + #define Z2_CURRENT 800 + #define Z2_MICROSTEPS 16 + #define Z2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Z3) + #define Z3_CURRENT 800 + #define Z3_MICROSTEPS 16 + #define Z3_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E0) + #define E0_CURRENT 650 + #define E0_MICROSTEPS 16 + #define E0_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E1) + #define E1_CURRENT 800 + #define E1_MICROSTEPS 16 + #define E1_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E2) + #define E2_CURRENT 800 + #define E2_MICROSTEPS 16 + #define E2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E3) + #define E3_CURRENT 800 + #define E3_MICROSTEPS 16 + #define E3_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E4) + #define E4_CURRENT 800 + #define E4_MICROSTEPS 16 + #define E4_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E5) + #define E5_CURRENT 800 + #define E5_MICROSTEPS 16 + #define E5_RSENSE 0.11 + #endif + + /** + * Override default SPI pins for TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160 drivers here. + * The default pins can be found in your board's pins file. + */ + //#define X_CS_PIN -1 + //#define Y_CS_PIN -1 + //#define Z_CS_PIN -1 + //#define X2_CS_PIN -1 + //#define Y2_CS_PIN -1 + //#define Z2_CS_PIN -1 + //#define Z3_CS_PIN -1 + //#define E0_CS_PIN -1 + //#define E1_CS_PIN -1 + //#define E2_CS_PIN -1 + //#define E3_CS_PIN -1 + //#define E4_CS_PIN -1 + //#define E5_CS_PIN -1 + + /** + * Software option for SPI driven drivers (TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160). + * The default SW SPI pins are defined the respective pins files, + * but you can override or define them here. + */ + //#define TMC_USE_SW_SPI + //#define TMC_SW_MOSI -1 + //#define TMC_SW_MISO -1 + //#define TMC_SW_SCK -1 + + /** + * Four TMC2209 drivers can use the same HW/SW serial port with hardware configured addresses. + * Set the address using jumpers on pins MS1 and MS2. + * Address | MS1 | MS2 + * 0 | LOW | LOW + * 1 | HIGH | LOW + * 2 | LOW | HIGH + * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. + */ + #define X_SLAVE_ADDRESS 0 + #define Y_SLAVE_ADDRESS 1 + #define Z_SLAVE_ADDRESS 2 + #define X2_SLAVE_ADDRESS 0 + #define Y2_SLAVE_ADDRESS 0 + #define Z2_SLAVE_ADDRESS 0 + #define Z3_SLAVE_ADDRESS 0 + #define E0_SLAVE_ADDRESS 3 + #define E1_SLAVE_ADDRESS 0 + #define E2_SLAVE_ADDRESS 0 + #define E3_SLAVE_ADDRESS 0 + #define E4_SLAVE_ADDRESS 0 + #define E5_SLAVE_ADDRESS 0 + + /** + * Software enable + * + * Use for drivers that do not use a dedicated enable pin, but rather handle the same + * function through a communication line such as SPI or UART. + */ + //#define SOFTWARE_DRIVER_ENABLE + + /** + * TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only + * Use Trinamic's ultra quiet stepping mode. + * When disabled, Marlin will use spreadCycle stepping mode. + */ + #define STEALTHCHOP_XY + #define STEALTHCHOP_Z + #define STEALTHCHOP_E + + /** + * Optimize spreadCycle chopper parameters by using predefined parameter sets + * or with the help of an example included in the library. + * Provided parameter sets are + * CHOPPER_DEFAULT_12V + * CHOPPER_DEFAULT_19V + * CHOPPER_DEFAULT_24V + * CHOPPER_DEFAULT_36V + * CHOPPER_PRUSAMK3_24V // Imported parameters from the official Prusa firmware for MK3 (24V) + * CHOPPER_MARLIN_119 // Old defaults from Marlin v1.1.9 + * + * Define you own with + * { , , hysteresis_start[1..8] } + */ + #define CHOPPER_TIMING CHOPPER_DEFAULT_12V + + /** + * Monitor Trinamic drivers for error conditions, + * like overtemperature and short to ground. + * In the case of overtemperature Marlin can decrease the driver current until error condition clears. + * Other detected conditions can be used to stop the current print. + * Relevant g-codes: + * M906 - Set or get motor current in milliamps using axis codes X, Y, Z, E. Report values if no axis codes given. + * M911 - Report stepper driver overtemperature pre-warn condition. + * M912 - Clear stepper driver overtemperature pre-warn condition flag. + * M122 - Report driver parameters (Requires TMC_DEBUG) + */ + #define MONITOR_DRIVER_STATUS + + #if ENABLED(MONITOR_DRIVER_STATUS) + #define CURRENT_STEP_DOWN 50 // [mA] + #define REPORT_CURRENT_CHANGE + #define STOP_ON_ERROR + #endif + + /** + * TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only + * The driver will switch to spreadCycle when stepper speed is over HYBRID_THRESHOLD. + * This mode allows for faster movements at the expense of higher noise levels. + * STEALTHCHOP_(XY|Z|E) must be enabled to use HYBRID_THRESHOLD. + * M913 X/Y/Z/E to live tune the setting + */ + //#define HYBRID_THRESHOLD + + #define X_HYBRID_THRESHOLD 100 // [mm/s] + #define X2_HYBRID_THRESHOLD 100 + #define Y_HYBRID_THRESHOLD 100 + #define Y2_HYBRID_THRESHOLD 100 + #define Z_HYBRID_THRESHOLD 3 + #define Z2_HYBRID_THRESHOLD 3 + #define Z3_HYBRID_THRESHOLD 3 + #define E0_HYBRID_THRESHOLD 30 + #define E1_HYBRID_THRESHOLD 30 + #define E2_HYBRID_THRESHOLD 30 + #define E3_HYBRID_THRESHOLD 30 + #define E4_HYBRID_THRESHOLD 30 + #define E5_HYBRID_THRESHOLD 30 + + /** + * TMC2130, TMC2160, TMC2209, TMC2660, TMC5130, and TMC5160 only + * Use StallGuard2 to sense an obstacle and trigger an endstop. + * Connect the stepper driver's DIAG1 pin to the X/Y endstop pin. + * X, Y, and Z homing will always be done in spreadCycle mode. + * + * X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity. + * Higher values make the system LESS sensitive. + * Lower value make the system MORE sensitive. + * Too low values can lead to false positives, while too high values will collide the axis without triggering. + * It is advised to set X/Y/Z_HOME_BUMP_MM to 0. + * M914 X/Y/Z to live tune the setting + */ + //#define SENSORLESS_HOMING // StallGuard capable drivers only + + /** + * Use StallGuard2 to probe the bed with the nozzle. + * + * CAUTION: This could cause damage to machines that use a lead screw or threaded rod + * to move the Z axis. Take extreme care when attempting to enable this feature. + */ + //#define SENSORLESS_PROBING // StallGuard capable drivers only + + #if EITHER(SENSORLESS_HOMING, SENSORLESS_PROBING) + // TMC2209: 0...255. TMC2130: -64...63 + #define X_STALL_SENSITIVITY 8 + #define Y_STALL_SENSITIVITY 8 + //#define Z_STALL_SENSITIVITY 8 + #endif + + /** + * Beta feature! + * Create a 50/50 square wave step pulse optimal for stepper drivers. + */ + //#define SQUARE_WAVE_STEPPING + + /** + * Enable M122 debugging command for TMC stepper drivers. + * M122 S0/1 will enable continous reporting. + */ + //#define TMC_DEBUG + + /** + * You can set your own advanced settings by filling in predefined functions. + * A list of available functions can be found on the library github page + * https://github.com/teemuatlut/TMCStepper + * + * Example: + * #define TMC_ADV() { \ + * stepperX.diag0_temp_prewarn(1); \ + * stepperY.interpolate(0); \ + * } + */ + #define TMC_ADV() { } + +#endif // HAS_TRINAMIC + +// @section L6470 + +/** + * L6470 Stepper Driver options + * + * Arduino-L6470 library (0.7.0 or higher) is required for this stepper driver. + * https://github.com/ameyer/Arduino-L6470 + * + * Requires the following to be defined in your pins_YOUR_BOARD file + * L6470_CHAIN_SCK_PIN + * L6470_CHAIN_MISO_PIN + * L6470_CHAIN_MOSI_PIN + * L6470_CHAIN_SS_PIN + * L6470_RESET_CHAIN_PIN (optional) + */ +#if HAS_DRIVER(L6470) + + //#define L6470_CHITCHAT // Display additional status info + + #if AXIS_DRIVER_TYPE_X(L6470) + #define X_MICROSTEPS 128 // Number of microsteps (VALID: 1, 2, 4, 8, 16, 32, 128) + #define X_OVERCURRENT 2000 // (mA) Current where the driver detects an over current (VALID: 375 x (1 - 16) - 6A max - rounds down) + #define X_STALLCURRENT 1500 // (mA) Current where the driver detects a stall (VALID: 31.25 * (1-128) - 4A max - rounds down) + #define X_MAX_VOLTAGE 127 // 0-255, Maximum effective voltage seen by stepper + #define X_CHAIN_POS 0 // Position in SPI chain, 0=Not in chain, 1=Nearest MOSI + #endif + + #if AXIS_DRIVER_TYPE_X2(L6470) + #define X2_MICROSTEPS 128 + #define X2_OVERCURRENT 2000 + #define X2_STALLCURRENT 1500 + #define X2_MAX_VOLTAGE 127 + #define X2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Y(L6470) + #define Y_MICROSTEPS 128 + #define Y_OVERCURRENT 2000 + #define Y_STALLCURRENT 1500 + #define Y_MAX_VOLTAGE 127 + #define Y_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Y2(L6470) + #define Y2_MICROSTEPS 128 + #define Y2_OVERCURRENT 2000 + #define Y2_STALLCURRENT 1500 + #define Y2_MAX_VOLTAGE 127 + #define Y2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Z(L6470) + #define Z_MICROSTEPS 128 + #define Z_OVERCURRENT 2000 + #define Z_STALLCURRENT 1500 + #define Z_MAX_VOLTAGE 127 + #define Z_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Z2(L6470) + #define Z2_MICROSTEPS 128 + #define Z2_OVERCURRENT 2000 + #define Z2_STALLCURRENT 1500 + #define Z2_MAX_VOLTAGE 127 + #define Z2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Z3(L6470) + #define Z3_MICROSTEPS 128 + #define Z3_OVERCURRENT 2000 + #define Z3_STALLCURRENT 1500 + #define Z3_MAX_VOLTAGE 127 + #define Z3_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E0(L6470) + #define E0_MICROSTEPS 128 + #define E0_OVERCURRENT 2000 + #define E0_STALLCURRENT 1500 + #define E0_MAX_VOLTAGE 127 + #define E0_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E1(L6470) + #define E1_MICROSTEPS 128 + #define E1_OVERCURRENT 2000 + #define E1_STALLCURRENT 1500 + #define E1_MAX_VOLTAGE 127 + #define E1_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E2(L6470) + #define E2_MICROSTEPS 128 + #define E2_OVERCURRENT 2000 + #define E2_STALLCURRENT 1500 + #define E2_MAX_VOLTAGE 127 + #define E2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E3(L6470) + #define E3_MICROSTEPS 128 + #define E3_OVERCURRENT 2000 + #define E3_STALLCURRENT 1500 + #define E3_MAX_VOLTAGE 127 + #define E3_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E4(L6470) + #define E4_MICROSTEPS 128 + #define E4_OVERCURRENT 2000 + #define E4_STALLCURRENT 1500 + #define E4_MAX_VOLTAGE 127 + #define E4_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E5(L6470) + #define E5_MICROSTEPS 128 + #define E5_OVERCURRENT 2000 + #define E5_STALLCURRENT 1500 + #define E5_MAX_VOLTAGE 127 + #define E5_CHAIN_POS 0 + #endif + + /** + * Monitor L6470 drivers for error conditions like over temperature and over current. + * In the case of over temperature Marlin can decrease the drive until the error condition clears. + * Other detected conditions can be used to stop the current print. + * Relevant g-codes: + * M906 - I1/2/3/4/5 Set or get motor drive level using axis codes X, Y, Z, E. Report values if no axis codes given. + * I not present or I0 or I1 - X, Y, Z or E0 + * I2 - X2, Y2, Z2 or E1 + * I3 - Z3 or E3 + * I4 - E4 + * I5 - E5 + * M916 - Increase drive level until get thermal warning + * M917 - Find minimum current thresholds + * M918 - Increase speed until max or error + * M122 S0/1 - Report driver parameters + */ + //#define MONITOR_L6470_DRIVER_STATUS + + #if ENABLED(MONITOR_L6470_DRIVER_STATUS) + #define KVAL_HOLD_STEP_DOWN 1 + //#define L6470_STOP_ON_ERROR + #endif + +#endif // L6470 + +/** + * TWI/I2C BUS + * + * This feature is an EXPERIMENTAL feature so it shall not be used on production + * machines. Enabling this will allow you to send and receive I2C data from slave + * devices on the bus. + * + * ; Example #1 + * ; This macro send the string "Marlin" to the slave device with address 0x63 (99) + * ; It uses multiple M260 commands with one B arg + * M260 A99 ; Target slave address + * M260 B77 ; M + * M260 B97 ; a + * M260 B114 ; r + * M260 B108 ; l + * M260 B105 ; i + * M260 B110 ; n + * M260 S1 ; Send the current buffer + * + * ; Example #2 + * ; Request 6 bytes from slave device with address 0x63 (99) + * M261 A99 B5 + * + * ; Example #3 + * ; Example serial output of a M261 request + * echo:i2c-reply: from:99 bytes:5 data:hello + */ + +// @section i2cbus + +//#define EXPERIMENTAL_I2CBUS +#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave + +// @section extras + +/** + * Photo G-code + * Add the M240 G-code to take a photo. + * The photo can be triggered by a digital pin or a physical movement. + */ +//#define PHOTO_GCODE +#if ENABLED(PHOTO_GCODE) + // A position to move to (and raise Z) before taking the photo + //#define PHOTO_POSITION { X_MAX_POS - 5, Y_MAX_POS, 0 } // { xpos, ypos, zraise } (M240 X Y Z) + //#define PHOTO_DELAY_MS 100 // (ms) Duration to pause before moving back (M240 P) + //#define PHOTO_RETRACT_MM 6.5 // (mm) E retract/recover for the photo move (M240 R S) + + // Canon RC-1 or homebrew digital camera trigger + // Data from: http://www.doc-diy.net/photo/rc-1_hacked/ + //#define PHOTOGRAPH_PIN 23 + + // Canon Hack Development Kit + // http://captain-slow.dk/2014/03/09/3d-printing-timelapses/ + //#define CHDK_PIN 4 + + // Optional second move with delay to trigger the camera shutter + //#define PHOTO_SWITCH_POSITION { X_MAX_POS, Y_MAX_POS } // { xpos, ypos } (M240 I J) + + // Duration to hold the switch or keep CHDK_PIN high + //#define PHOTO_SWITCH_MS 50 // (ms) (M240 D) +#endif + +/** + * Spindle & Laser control + * + * Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and + * to set spindle speed, spindle direction, and laser power. + * + * SuperPid is a router/spindle speed controller used in the CNC milling community. + * Marlin can be used to turn the spindle on and off. It can also be used to set + * the spindle speed from 5,000 to 30,000 RPM. + * + * You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V + * hardware PWM pin for the speed control and a pin for the rotation direction. + * + * See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details. + */ +//#define SPINDLE_FEATURE +//#define LASER_FEATURE +#if EITHER(SPINDLE_FEATURE, LASER_FEATURE) + #define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH + #define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power + #define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower + #define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power + #define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop + + #if ENABLED(SPINDLE_FEATURE) + //#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction + #define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction + #define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed + + /** + * The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power + * + * SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT + * where PWM duty cycle varies from 0 to 255 + * + * set the following for your controller (ALL MUST BE SET) + */ + #define SPEED_POWER_SLOPE 118.4 + #define SPEED_POWER_INTERCEPT 0 + #define SPEED_POWER_MIN 5000 + #define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM + #else + #define SPEED_POWER_SLOPE 0.3922 + #define SPEED_POWER_INTERCEPT 0 + #define SPEED_POWER_MIN 10 + #define SPEED_POWER_MAX 100 // 0-100% + #endif +#endif + +/** + * Coolant Control + * + * Add the M7, M8, and M9 commands to turn mist or flood coolant on and off. + * + * Note: COOLANT_MIST_PIN and/or COOLANT_FLOOD_PIN must also be defined. + */ +//#define COOLANT_CONTROL +#if ENABLED(COOLANT_CONTROL) + #define COOLANT_MIST // Enable if mist coolant is present + #define COOLANT_FLOOD // Enable if flood coolant is present + #define COOLANT_MIST_INVERT false // Set "true" if the on/off function is reversed + #define COOLANT_FLOOD_INVERT false // Set "true" if the on/off function is reversed +#endif + +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define FILWIDTH_ERROR_MARGIN 1.0 // (mm) If a measurement differs too much from nominal width ignore it + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + +/** + * CNC Coordinate Systems + * + * Enables G53 and G54-G59.3 commands to select coordinate systems + * and G92.1 to reset the workspace to native machine space. + */ +//#define CNC_COORDINATE_SYSTEMS + +/** + * Auto-report temperatures with M155 S + */ +#define AUTO_REPORT_TEMPERATURES + +/** + * Include capabilities in M115 output + */ +#define EXTENDED_CAPABILITIES_REPORT + +/** + * Disable all Volumetric extrusion options + */ +//#define NO_VOLUMETRICS + +#if DISABLED(NO_VOLUMETRICS) + /** + * Volumetric extrusion default state + * Activate to make volumetric extrusion the default method, + * with DEFAULT_NOMINAL_FILAMENT_DIA as the default diameter. + * + * M200 D0 to disable, M200 Dn to set a new diameter. + */ + //#define VOLUMETRIC_DEFAULT_ON +#endif + +/** + * Enable this option for a leaner build of Marlin that removes all + * workspace offsets, simplifying coordinate transformations, leveling, etc. + * + * - M206 and M428 are disabled. + * - G92 will revert to its behavior from Marlin 1.0. + */ +//#define NO_WORKSPACE_OFFSETS + +/** + * Set the number of proportional font spaces required to fill up a typical character space. + * This can help to better align the output of commands like `G29 O` Mesh Output. + * + * For clients that use a fixed-width font (like OctoPrint), leave this set to 1.0. + * Otherwise, adjust according to your client and font. + */ +#define PROPORTIONAL_FONT_RATIO 1.0 + +/** + * Spend 28 bytes of SRAM to optimize the GCode parser + */ +#define FASTER_GCODE_PARSER + +/** + * CNC G-code options + * Support CNC-style G-code dialects used by laser cutters, drawing machine cams, etc. + * Note that G0 feedrates should be used with care for 3D printing (if used at all). + * High feedrates may cause ringing and harm print quality. + */ +//#define PAREN_COMMENTS // Support for parentheses-delimited comments +//#define GCODE_MOTION_MODES // Remember the motion mode (G0 G1 G2 G3 G5 G38.X) and apply for X Y Z E F, etc. + +// Enable and set a (default) feedrate for all G0 moves +//#define G0_FEEDRATE 3000 // (mm/m) +#ifdef G0_FEEDRATE + //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode +#endif + +/** + * G-code Macros + * + * Add G-codes M810-M819 to define and run G-code macros. + * Macros are not saved to EEPROM. + */ +//#define GCODE_MACROS +#if ENABLED(GCODE_MACROS) + #define GCODE_MACROS_SLOTS 5 // Up to 10 may be used + #define GCODE_MACROS_SLOT_SIZE 50 // Maximum length of a single macro +#endif + +/** + * User-defined menu items that execute custom GCode + */ +//#define CUSTOM_USER_MENUS +#if ENABLED(CUSTOM_USER_MENUS) + //#define CUSTOM_USER_MENU_TITLE "Custom Commands" + #define USER_SCRIPT_DONE "M117 User Script Done" + #define USER_SCRIPT_AUDIBLE_FEEDBACK + //#define USER_SCRIPT_RETURN // Return to status screen after a script + + #define USER_DESC_1 "Home & UBL Info" + #define USER_GCODE_1 "G28\nG29 W" + + #define USER_DESC_2 "Preheat for " PREHEAT_1_LABEL + #define USER_GCODE_2 "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND) + + #define USER_DESC_3 "Preheat for " PREHEAT_2_LABEL + #define USER_GCODE_3 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND) + + #define USER_DESC_4 "Heat Bed/Home/Level" + #define USER_GCODE_4 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29" + + #define USER_DESC_5 "Home & Info" + #define USER_GCODE_5 "G28\nM503" +#endif + +/** + * Host Action Commands + * + * Define host streamer action commands in compliance with the standard. + * + * See https://reprap.org/wiki/G-code#Action_commands + * Common commands ........ poweroff, pause, paused, resume, resumed, cancel + * G29_RETRY_AND_RECOVER .. probe_rewipe, probe_failed + * + * Some features add reason codes to extend these commands. + * + * Host Prompt Support enables Marlin to use the host for user prompts so + * filament runout and other processes can be managed from the host side. + */ +//#define HOST_ACTION_COMMANDS +#if ENABLED(HOST_ACTION_COMMANDS) + //#define HOST_PROMPT_SUPPORT +#endif + +//=========================================================================== +//====================== I2C Position Encoder Settings ====================== +//=========================================================================== + +/** + * I2C position encoders for closed loop control. + * Developed by Chris Barr at Aus3D. + * + * Wiki: http://wiki.aus3d.com.au/Magnetic_Encoder + * Github: https://github.com/Aus3D/MagneticEncoder + * + * Supplier: http://aus3d.com.au/magnetic-encoder-module + * Alternative Supplier: http://reliabuild3d.com/ + * + * Reliabuild encoders have been modified to improve reliability. + */ + +//#define I2C_POSITION_ENCODERS +#if ENABLED(I2C_POSITION_ENCODERS) + + #define I2CPE_ENCODER_CNT 1 // The number of encoders installed; max of 5 + // encoders supported currently. + + #define I2CPE_ENC_1_ADDR I2CPE_PRESET_ADDR_X // I2C address of the encoder. 30-200. + #define I2CPE_ENC_1_AXIS X_AXIS // Axis the encoder module is installed on. _AXIS. + #define I2CPE_ENC_1_TYPE I2CPE_ENC_TYPE_LINEAR // Type of encoder: I2CPE_ENC_TYPE_LINEAR -or- + // I2CPE_ENC_TYPE_ROTARY. + #define I2CPE_ENC_1_TICKS_UNIT 2048 // 1024 for magnetic strips with 2mm poles; 2048 for + // 1mm poles. For linear encoders this is ticks / mm, + // for rotary encoders this is ticks / revolution. + //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper + // steps per full revolution (motor steps/rev * microstepping) + //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the + // printer will attempt to correct the error; errors + // smaller than this are ignored to minimize effects of + // measurement noise / latency (filter). + + #define I2CPE_ENC_2_ADDR I2CPE_PRESET_ADDR_Y // Same as above, but for encoder 2. + #define I2CPE_ENC_2_AXIS Y_AXIS + #define I2CPE_ENC_2_TYPE I2CPE_ENC_TYPE_LINEAR + #define I2CPE_ENC_2_TICKS_UNIT 2048 + //#define I2CPE_ENC_2_TICKS_REV (16 * 200) + //#define I2CPE_ENC_2_INVERT + #define I2CPE_ENC_2_EC_METHOD I2CPE_ECM_MICROSTEP + #define I2CPE_ENC_2_EC_THRESH 0.10 + + #define I2CPE_ENC_3_ADDR I2CPE_PRESET_ADDR_Z // Encoder 3. Add additional configuration options + #define I2CPE_ENC_3_AXIS Z_AXIS // as above, or use defaults below. + + #define I2CPE_ENC_4_ADDR I2CPE_PRESET_ADDR_E // Encoder 4. + #define I2CPE_ENC_4_AXIS E_AXIS + + #define I2CPE_ENC_5_ADDR 34 // Encoder 5. + #define I2CPE_ENC_5_AXIS E_AXIS + + // Default settings for encoders which are enabled, but without settings configured above. + #define I2CPE_DEF_TYPE I2CPE_ENC_TYPE_LINEAR + #define I2CPE_DEF_ENC_TICKS_UNIT 2048 + #define I2CPE_DEF_TICKS_REV (16 * 200) + #define I2CPE_DEF_EC_METHOD I2CPE_ECM_NONE + #define I2CPE_DEF_EC_THRESH 0.1 + + //#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given + // axis after which the printer will abort. Comment out to + // disable abort behavior. + + #define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault + // for this amount of time (in ms) before the encoder + // is trusted again. + + /** + * Position is checked every time a new command is executed from the buffer but during long moves, + * this setting determines the minimum update time between checks. A value of 100 works well with + * error rolling average when attempting to correct only for skips and not for vibration. + */ + #define I2CPE_MIN_UPD_TIME_MS 4 // (ms) Minimum time between encoder checks. + + // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise. + #define I2CPE_ERR_ROLLING_AVERAGE + +#endif // I2C_POSITION_ENCODERS + +/** + * MAX7219 Debug Matrix + * + * Add support for a low-cost 8x8 LED Matrix based on the Max7219 chip as a realtime status display. + * Requires 3 signal wires. Some useful debug options are included to demonstrate its usage. + */ +//#define MAX7219_DEBUG +#if ENABLED(MAX7219_DEBUG) + #define MAX7219_CLK_PIN 64 + #define MAX7219_DIN_PIN 57 + #define MAX7219_LOAD_PIN 44 + + //#define MAX7219_GCODE // Add the M7219 G-code to control the LED matrix + #define MAX7219_INIT_TEST 2 // Do a test pattern at initialization (Set to 2 for spiral) + #define MAX7219_NUMBER_UNITS 1 // Number of Max7219 units in chain. + #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) + // connector at: right=0 bottom=-90 top=90 left=180 + //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side + + /** + * Sample debug features + * If you add more debug displays, be careful to avoid conflicts! + */ + #define MAX7219_DEBUG_PRINTER_ALIVE // Blink corner LED of 8x8 matrix to show that the firmware is functioning + #define MAX7219_DEBUG_PLANNER_HEAD 3 // Show the planner queue head position on this and the next LED matrix row + #define MAX7219_DEBUG_PLANNER_TAIL 5 // Show the planner queue tail position on this and the next LED matrix row + + #define MAX7219_DEBUG_PLANNER_QUEUE 0 // Show the current planner queue depth on this and the next LED matrix row + // If you experience stuttering, reboots, etc. this option can reveal how + // tweaks made to the configuration are affecting the printer in real-time. +#endif + +/** + * NanoDLP Sync support + * + * Add support for Synchronized Z moves when using with NanoDLP. G0/G1 axis moves will output "Z_move_comp" + * string to enable synchronization with DLP projector exposure. This change will allow to use + * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands + */ +//#define NANODLP_Z_SYNC +#if ENABLED(NANODLP_Z_SYNC) + //#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move. + // Default behavior is limited to Z axis only. +#endif + +/** + * WiFi Support (Espressif ESP32 WiFi) + */ +//#define WIFISUPPORT +#if ENABLED(WIFISUPPORT) + #define WIFI_SSID "Wifi SSID" + #define WIFI_PWD "Wifi Password" + //#define WEBSUPPORT // Start a webserver with auto-discovery + //#define OTASUPPORT // Support over-the-air firmware updates +#endif + +/** + * Prusa Multi-Material Unit v2 + * Enable in Configuration.h + */ +#if ENABLED(PRUSA_MMU2) + + // Serial port used for communication with MMU2. + // For AVR enable the UART port used for the MMU. (e.g., internalSerial) + // For 32-bit boards check your HAL for available serial ports. (e.g., Serial2) + #define INTERNAL_SERIAL_PORT 2 + #define MMU2_SERIAL internalSerial + + // Use hardware reset for MMU if a pin is defined for it + //#define MMU2_RST_PIN 23 + + // Enable if the MMU2 has 12V stepper motors (MMU2 Firmware 1.0.2 and up) + //#define MMU2_MODE_12V + + // G-code to execute when MMU2 F.I.N.D.A. probe detects filament runout + #define MMU2_FILAMENT_RUNOUT_SCRIPT "M600" + + // Add an LCD menu for MMU2 + //#define MMU2_MENUS + #if ENABLED(MMU2_MENUS) + // Settings for filament load / unload from the LCD menu. + // This is for Prusa MK3-style extruders. Customize for your hardware. + #define MMU2_FILAMENTCHANGE_EJECT_FEED 80.0 + #define MMU2_LOAD_TO_NOZZLE_SEQUENCE \ + { 7.2, 562 }, \ + { 14.4, 871 }, \ + { 36.0, 1393 }, \ + { 14.4, 871 }, \ + { 50.0, 198 } + + #define MMU2_RAMMING_SEQUENCE \ + { 1.0, 1000 }, \ + { 1.0, 1500 }, \ + { 2.0, 2000 }, \ + { 1.5, 3000 }, \ + { 2.5, 4000 }, \ + { -15.0, 5000 }, \ + { -14.0, 1200 }, \ + { -6.0, 600 }, \ + { 10.0, 700 }, \ + { -10.0, 400 }, \ + { -50.0, 2000 } + + #endif + + //#define MMU2_DEBUG // Write debug info to serial output + +#endif // PRUSA_MMU2 + +/** + * Advanced Print Counter settings + */ +#if ENABLED(PRINTCOUNTER) + #define SERVICE_WARNING_BUZZES 3 + // Activate up to 3 service interval watchdogs + //#define SERVICE_NAME_1 "Service S" + //#define SERVICE_INTERVAL_1 100 // print hours + //#define SERVICE_NAME_2 "Service L" + //#define SERVICE_INTERVAL_2 200 // print hours + //#define SERVICE_NAME_3 "Service 3" + //#define SERVICE_INTERVAL_3 1 // print hours +#endif + +// @section develop + +/** + * M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins + */ +//#define PINS_DEBUGGING + +// Enable Marlin dev mode which adds some special commands +//#define MARLIN_DEV_MODE diff --git a/config/examples/Felix/Configuration.h b/config/examples/Felix/Configuration.h index 710143f880..fa343114a1 100644 --- a/config/examples/Felix/Configuration.h +++ b/config/examples/Felix/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_FELIX2 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Felix" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -502,7 +508,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. // Felix Foil Heater @@ -1505,8 +1511,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1663,6 +1672,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1890,31 +1907,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1948,15 +1946,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1969,6 +1958,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -1994,17 +2025,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2100,8 +2138,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Felix/Configuration_adv.h b/config/examples/Felix/Configuration_adv.h index 70743ab611..cce91e29f0 100644 --- a/config/examples/Felix/Configuration_adv.h +++ b/config/examples/Felix/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Felix/DUAL/Configuration.h b/config/examples/Felix/DUAL/Configuration.h index 25b549fa3b..55d90f3bec 100644 --- a/config/examples/Felix/DUAL/Configuration.h +++ b/config/examples/Felix/DUAL/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_FELIX2 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Felix Dual" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 1 @@ -502,7 +508,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. // Felix Foil Heater @@ -1505,8 +1511,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1663,6 +1672,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1890,31 +1907,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1948,15 +1946,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1969,6 +1958,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -1994,17 +2025,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2100,8 +2138,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/FlashForge/CreatorPro/Configuration.h b/config/examples/FlashForge/CreatorPro/Configuration.h index cdc0feba23..8593ba50e5 100644 --- a/config/examples/FlashForge/CreatorPro/Configuration.h +++ b/config/examples/FlashForge/CreatorPro/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_MIGHTYBOARD_REVE #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "CreatorPro" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 -2 #define TEMP_SENSOR_1 -2 @@ -504,7 +510,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1514,8 +1520,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1672,6 +1681,14 @@ // #define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1899,31 +1916,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1957,15 +1955,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1978,6 +1967,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2003,17 +2034,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2109,8 +2147,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/FlashForge/CreatorPro/Configuration_adv.h b/config/examples/FlashForge/CreatorPro/Configuration_adv.h index 096c72c9f8..fdefc6ecbe 100644 --- a/config/examples/FlashForge/CreatorPro/Configuration_adv.h +++ b/config/examples/FlashForge/CreatorPro/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" //#define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -850,6 +851,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1036,7 +1040,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1134,6 +1138,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1363,6 +1368,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1748,6 +1756,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2433,6 +2444,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/FolgerTech/i3-2020/Configuration.h b/config/examples/FolgerTech/i3-2020/Configuration.h index 3261d4a679..55d652363f 100644 --- a/config/examples/FolgerTech/i3-2020/Configuration.h +++ b/config/examples/FolgerTech/i3-2020/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_RAMPS_14_EFB #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "FT-2020 v9" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -519,7 +525,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1529,8 +1535,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1687,6 +1696,14 @@ // #define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1914,31 +1931,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1972,15 +1970,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1993,6 +1982,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2018,17 +2049,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2124,8 +2162,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/FolgerTech/i3-2020/Configuration_adv.h b/config/examples/FolgerTech/i3-2020/Configuration_adv.h index 754b4bd6d3..3ceb073dfe 100644 --- a/config/examples/FolgerTech/i3-2020/Configuration_adv.h +++ b/config/examples/FolgerTech/i3-2020/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2442,6 +2453,7 @@ #define MAX7219_ROTATE -90 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Formbot/Raptor/Configuration.h b/config/examples/Formbot/Raptor/Configuration.h index 27185602bd..1c4e4e3149 100644 --- a/config/examples/Formbot/Raptor/Configuration.h +++ b/config/examples/Formbot/Raptor/Configuration.h @@ -170,18 +170,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_FORMBOT_RAPTOR #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "TM3D RaPtOr" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -318,7 +316,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -400,6 +405,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -436,7 +442,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -566,7 +572,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1628,8 +1634,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1786,6 +1795,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -2013,31 +2030,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -2071,15 +2069,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -2092,6 +2081,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2117,17 +2148,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2223,8 +2261,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Formbot/Raptor/Configuration_adv.h b/config/examples/Formbot/Raptor/Configuration_adv.h index 0f9c68ff1e..55ccb5a2e7 100644 --- a/config/examples/Formbot/Raptor/Configuration_adv.h +++ b/config/examples/Formbot/Raptor/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu #define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1168,7 +1173,7 @@ //#define BABYSTEP_WITHOUT_HOMING //#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA! #define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way - #define BABYSTEP_MULTIPLICATOR 25 // Babysteps are very small. Increase for faster motion. + #define BABYSTEP_MULTIPLICATOR 25 // Babysteps are very small. Increase for faster motion. #define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping. #if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING) @@ -1366,6 +1371,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1751,6 +1759,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2438,6 +2449,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Formbot/T_Rex_2+/Configuration.h b/config/examples/Formbot/T_Rex_2+/Configuration.h index 2c4911259a..cf3236d7f4 100644 --- a/config/examples/Formbot/T_Rex_2+/Configuration.h +++ b/config/examples/Formbot/T_Rex_2+/Configuration.h @@ -132,18 +132,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_FORMBOT_TREX2PLUS #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "T-Rex 2+" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -280,7 +278,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -368,6 +373,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -404,7 +410,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 1 @@ -536,7 +542,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. #ifdef ROXYs_TRex @@ -1557,8 +1563,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1715,6 +1724,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1942,31 +1959,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -2000,15 +1998,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -2021,6 +2010,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2046,17 +2077,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2152,8 +2190,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h index 1bfb3dac50..b3d543a2ae 100644 --- a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h +++ b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h @@ -654,6 +654,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -855,6 +856,9 @@ // Include a page of printer information in the LCD Main Menu #define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -1041,7 +1045,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1139,6 +1143,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1368,6 +1373,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1753,6 +1761,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2447,7 +2458,8 @@ #define MAX7219_NUMBER_UNITS 3 // Number of Max7219 units in chain. #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 - #define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + #define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Formbot/T_Rex_3/Configuration.h b/config/examples/Formbot/T_Rex_3/Configuration.h index be198e7f4c..01e2919e66 100644 --- a/config/examples/Formbot/T_Rex_3/Configuration.h +++ b/config/examples/Formbot/T_Rex_3/Configuration.h @@ -133,18 +133,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_FORMBOT_TREX3 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "T-Rex 3" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -281,7 +279,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -363,6 +368,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -399,7 +405,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 1 @@ -523,7 +529,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1548,8 +1554,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1709,6 +1718,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1936,31 +1953,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1994,15 +1992,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -2015,6 +2004,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2040,17 +2071,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2146,8 +2184,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Formbot/T_Rex_3/Configuration_adv.h b/config/examples/Formbot/T_Rex_3/Configuration_adv.h index 0e8b28f95f..9bbbee1f2d 100644 --- a/config/examples/Formbot/T_Rex_3/Configuration_adv.h +++ b/config/examples/Formbot/T_Rex_3/Configuration_adv.h @@ -654,6 +654,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -855,6 +856,9 @@ // Include a page of printer information in the LCD Main Menu #define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -1041,7 +1045,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1139,6 +1143,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1368,6 +1373,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1753,6 +1761,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2443,6 +2454,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Fysetc/AIO_II/Configuration.h b/config/examples/Fysetc/AIO_II/Configuration.h index 6fd40430e6..8f87e45ea6 100644 --- a/config/examples/Fysetc/AIO_II/Configuration.h +++ b/config/examples/Fysetc/AIO_II/Configuration.h @@ -104,7 +104,7 @@ * * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] */ -#define SERIAL_PORT 1 // fzl:由于libmaple 0 用的是USB，1才是串口 old:0 +#define SERIAL_PORT 1 // libmaple 0 for USB ,1 for serial /** * Select a secondary serial port on the board to use for communication with the host. @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_FYSETC_AIO_II #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu //#define CUSTOM_MACHINE_NAME "3D Printer" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -150,7 +148,7 @@ #define EXTRUDERS 1 // Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc. -#define DEFAULT_NOMINAL_FILAMENT_DIA 3.0 +#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 // For Cyclops or any "multi-extruder" that shares a single nozzle. //#define SINGLENOZZLE @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -467,10 +473,15 @@ // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it + // Makerlab J-head + #define DEFAULT_Kp 21.73 + #define DEFAULT_Ki 1.54 + #define DEFAULT_Kd 76.55 + // Ultimaker - #define DEFAULT_Kp 22.2 - #define DEFAULT_Ki 1.08 - #define DEFAULT_Kd 114 + //#define DEFAULT_Kp 22.2 + //#define DEFAULT_Ki 1.08 + //#define DEFAULT_Kd 114 // MakerGear //#define DEFAULT_Kp 7.0 @@ -514,7 +525,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -630,9 +641,9 @@ #endif // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup). -#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop. -#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop. -#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop. +#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. #define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. #define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. #define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. @@ -739,9 +750,15 @@ #define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts #define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves -// -// Use Junction Deviation instead of traditional Jerk Limiting -// +/** + * Junction Deviation + * + * Use Junction Deviation instead of traditional Jerk Limiting + * + * See: + * https://reprap.org/forum/read.php?1,739819 + * http://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html + */ //#define JUNCTION_DEVIATION #if ENABLED(JUNCTION_DEVIATION) #define JUNCTION_DEVIATION_MM 0.02 // (mm) Distance from real junction edge @@ -972,10 +989,10 @@ // For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 // :{ 0:'Low', 1:'High' } -#define X_ENABLE_ON 1 -#define Y_ENABLE_ON 1 -#define Z_ENABLE_ON 1 -#define E_ENABLE_ON 1 // For all extruders +#define X_ENABLE_ON 0 +#define Y_ENABLE_ON 0 +#define Z_ENABLE_ON 0 +#define E_ENABLE_ON 0 // For all extruders // Disables axis stepper immediately when it's not being used. // WARNING: When motors turn off there is a chance of losing position accuracy! @@ -994,14 +1011,14 @@ // @section machine // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way. -#define INVERT_X_DIR false -#define INVERT_Y_DIR false -#define INVERT_Z_DIR true +#define INVERT_X_DIR true +#define INVERT_Y_DIR true +#define INVERT_Z_DIR false // @section extruder // For direct drive extruder v9 set to true, for geared extruder set to false. -#define INVERT_E0_DIR false +#define INVERT_E0_DIR true #define INVERT_E1_DIR false #define INVERT_E2_DIR false #define INVERT_E3_DIR false @@ -1026,8 +1043,8 @@ // @section machine // The size of the print bed -#define X_BED_SIZE 200 -#define Y_BED_SIZE 200 +#define X_BED_SIZE 235 +#define Y_BED_SIZE 235 // Travel limits (mm) after homing, corresponding to endstop positions. #define X_MIN_POS 0 @@ -1035,7 +1052,7 @@ #define Z_MIN_POS 0 #define X_MAX_POS X_BED_SIZE #define Y_MAX_POS Y_BED_SIZE -#define Z_MAX_POS 200 +#define Z_MAX_POS 260 /** * Software Endstops @@ -1394,7 +1411,7 @@ * M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes) * M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.) */ -//#define EEPROM_SETTINGS // Persistent storage with M500 and M501 +#define EEPROM_SETTINGS // Persistent storage with M500 and M501 //#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release! #define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM. #if ENABLED(EEPROM_SETTINGS) @@ -1517,8 +1534,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1675,6 +1695,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1902,31 +1930,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1939,7 +1948,7 @@ // //#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default //#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) -//#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight +#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight //#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight // @@ -1960,15 +1969,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1981,6 +1981,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2006,17 +2048,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2098,22 +2147,24 @@ * LED Type. Enable only one of the following two options. * */ -//#define RGB_LED +#define RGB_LED //#define RGBW_LED #if EITHER(RGB_LED, RGBW_LED) - //#define RGB_LED_R_PIN 34 - //#define RGB_LED_G_PIN 43 - //#define RGB_LED_B_PIN 35 - //#define RGB_LED_W_PIN -1 + #define RGB_LED_R_PIN PB0 + #define RGB_LED_G_PIN PB6 + #define RGB_LED_B_PIN PB7 + #define RGB_LED_W_PIN -1 #endif // Support for Adafruit Neopixel LED driver //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup @@ -2162,3 +2213,9 @@ // Allow servo angle to be edited and saved to EEPROM //#define EDITABLE_SERVO_ANGLES + +/** + * Sometimes after inserting the SD card settings get lost. + * This option reloads settings when the SD card is inserted. + */ +#define SD_RELOAD_SETTINGS diff --git a/config/examples/Fysetc/AIO_II/Configuration_adv.h b/config/examples/Fysetc/AIO_II/Configuration_adv.h index 1a5cff30fb..2c498e1556 100644 --- a/config/examples/Fysetc/AIO_II/Configuration_adv.h +++ b/config/examples/Fysetc/AIO_II/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -879,7 +883,7 @@ * LED Control Menu * Enable this feature to add LED Control to the LCD menu */ -//#define LED_CONTROL_MENU +#define LED_CONTROL_MENU #if ENABLED(LED_CONTROL_MENU) #define LED_COLOR_PRESETS // Enable the Preset Color menu option #if ENABLED(LED_COLOR_PRESETS) @@ -912,7 +916,7 @@ //#define MENU_ADDAUTOSTART // Add a menu option to run auto#.g files - #define EVENT_GCODE_SD_STOP "G28XY" // G-code to run on Stop Print (e.g., "G28XY" or "G27") + #define EVENT_GCODE_SD_STOP "M21" // G-code to run on Stop Print (e.g., "G28XY" or "G27") /** * Continue after Power-Loss (Creality3D) @@ -966,8 +970,8 @@ #define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 g-code. #define SDSORT_USES_RAM true // Pre-allocate a static array for faster pre-sorting. #define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.) - #define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option. - #define SDSORT_DYNAMIC_RAM true // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use! + #define SDSORT_CACHE_NAMES true // Keep sorted items in RAM longer for speedy performance. Most expensive option. + #define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use! #define SDSORT_CACHE_VFATS 2 // Maximum number of 13-byte VFAT entries to use for sorting. // Note: Only affects SCROLL_LONG_FILENAMES with SDSORT_CACHE_NAMES but not SDSORT_DYNAMIC_RAM. #endif @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1636,7 +1644,7 @@ #define INTERPOLATE true // Interpolate X/Y/Z_MICROSTEPS to 256 #if AXIS_IS_TMC(X) - #define X_CURRENT 800 // (mA) RMS current. Multiply by 1.414 for peak current. + #define X_CURRENT 700 // (mA) RMS current. Multiply by 1.414 for peak current. #define X_MICROSTEPS 16 // 0..256 #define X_RSENSE 0.11 #endif @@ -1648,7 +1656,7 @@ #endif #if AXIS_IS_TMC(Y) - #define Y_CURRENT 800 + #define Y_CURRENT 650 #define Y_MICROSTEPS 16 #define Y_RSENSE 0.11 #endif @@ -1678,7 +1686,7 @@ #endif #if AXIS_IS_TMC(E0) - #define E0_CURRENT 800 + #define E0_CURRENT 650 #define E0_MICROSTEPS 16 #define E0_RSENSE 0.11 #endif @@ -1749,15 +1757,18 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 - #define Y_SLAVE_ADDRESS 0 - #define Z_SLAVE_ADDRESS 0 + #define Y_SLAVE_ADDRESS 1 + #define Z_SLAVE_ADDRESS 2 #define X2_SLAVE_ADDRESS 0 #define Y2_SLAVE_ADDRESS 0 #define Z2_SLAVE_ADDRESS 0 #define Z3_SLAVE_ADDRESS 0 - #define E0_SLAVE_ADDRESS 0 + #define E0_SLAVE_ADDRESS 3 #define E1_SLAVE_ADDRESS 0 #define E2_SLAVE_ADDRESS 0 #define E3_SLAVE_ADDRESS 0 @@ -1808,7 +1819,7 @@ * M912 - Clear stepper driver overtemperature pre-warn condition flag. * M122 - Report driver parameters (Requires TMC_DEBUG) */ - //#define MONITOR_DRIVER_STATUS + #define MONITOR_DRIVER_STATUS #if ENABLED(MONITOR_DRIVER_STATUS) #define CURRENT_STEP_DOWN 50 // [mA] @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Fysetc/F6_13/Configuration.h b/config/examples/Fysetc/F6_13/Configuration.h index 9e314b8672..a447977ecd 100644 --- a/config/examples/Fysetc/F6_13/Configuration.h +++ b/config/examples/Fysetc/F6_13/Configuration.h @@ -129,20 +129,18 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD //#define MOTHERBOARD BOARD_RAMPS_14_EFB //#define MOTHERBOARD BOARD_FYSETC_AIO_II #define MOTHERBOARD BOARD_FYSETC_F6_13 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu //#define CUSTOM_MACHINE_NAME "3D Printer" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -279,7 +277,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -361,6 +366,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -397,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -516,7 +522,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -741,9 +747,15 @@ #define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts #define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves -// -// Use Junction Deviation instead of traditional Jerk Limiting -// +/** + * Junction Deviation + * + * Use Junction Deviation instead of traditional Jerk Limiting + * + * See: + * https://reprap.org/forum/read.php?1,739819 + * http://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html + */ //#define JUNCTION_DEVIATION #if ENABLED(JUNCTION_DEVIATION) #define JUNCTION_DEVIATION_MM 0.02 // (mm) Distance from real junction edge @@ -1519,8 +1531,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1677,6 +1692,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1904,31 +1927,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1962,15 +1966,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1983,6 +1978,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2008,17 +2045,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2118,8 +2162,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Fysetc/F6_13/Configuration_adv.h b/config/examples/Fysetc/F6_13/Configuration_adv.h index f16f1268b5..2b6722ede5 100644 --- a/config/examples/Fysetc/F6_13/Configuration_adv.h +++ b/config/examples/Fysetc/F6_13/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Geeetech/A10/Configuration.h b/config/examples/Geeetech/A10/Configuration.h index 1038ab9691..7ed65059a8 100644 --- a/config/examples/Geeetech/A10/Configuration.h +++ b/config/examples/Geeetech/A10/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_GT2560_V3 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Geeetech A10" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -504,7 +510,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. // MeCreator2 generated by Autotune @@ -1508,8 +1514,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1666,6 +1675,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1893,31 +1910,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1951,15 +1949,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1972,6 +1961,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -1997,17 +2028,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2103,8 +2141,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Geeetech/A10/Configuration_adv.h b/config/examples/Geeetech/A10/Configuration_adv.h index b9e680bc11..2a38b807d5 100644 --- a/config/examples/Geeetech/A10/Configuration_adv.h +++ b/config/examples/Geeetech/A10/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu #define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Geeetech/A10M/Configuration.h b/config/examples/Geeetech/A10M/Configuration.h index 6c976b0840..0f29847289 100644 --- a/config/examples/Geeetech/A10M/Configuration.h +++ b/config/examples/Geeetech/A10M/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_GT2560_V3 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Geeetech A10M" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -504,7 +510,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. // MeCreator2 generated by Autotune @@ -1508,8 +1514,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1666,6 +1675,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1893,31 +1910,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1951,15 +1949,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1972,6 +1961,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -1997,17 +2028,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2103,8 +2141,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Geeetech/A10M/Configuration_adv.h b/config/examples/Geeetech/A10M/Configuration_adv.h index 00c93e334a..2d2a5ff2e0 100644 --- a/config/examples/Geeetech/A10M/Configuration_adv.h +++ b/config/examples/Geeetech/A10M/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu #define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Geeetech/A20M/Configuration.h b/config/examples/Geeetech/A20M/Configuration.h index 6a3ecfa18c..887d277e48 100644 --- a/config/examples/Geeetech/A20M/Configuration.h +++ b/config/examples/Geeetech/A20M/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_GT2560_V3_A20 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Geeetech A20M" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -504,7 +510,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. // MeCreator2 generated by Autotune @@ -1507,8 +1513,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1665,6 +1674,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1895,31 +1912,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1953,15 +1951,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1974,6 +1963,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -1999,17 +2030,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2105,8 +2143,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Geeetech/A20M/Configuration_adv.h b/config/examples/Geeetech/A20M/Configuration_adv.h index 31bc5d0e52..6d1147bc5b 100644 --- a/config/examples/Geeetech/A20M/Configuration_adv.h +++ b/config/examples/Geeetech/A20M/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu #define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Geeetech/GT2560/Configuration.h b/config/examples/Geeetech/GT2560/Configuration.h index 3da73e70cd..7a717755b9 100644 --- a/config/examples/Geeetech/GT2560/Configuration.h +++ b/config/examples/Geeetech/GT2560/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_GT2560_REV_A #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu //#define CUSTOM_MACHINE_NAME "3D Printer" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -524,7 +530,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //12v (120 watt?) MK2a PCB Heatbed into 4mm borosilicate (Geeetech Prusa i3 Pro, Pro/B/C/X) @@ -1538,8 +1544,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1696,6 +1705,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1923,31 +1940,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1981,15 +1979,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -2002,6 +1991,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2027,17 +2058,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2133,8 +2171,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h index 886c86b18d..5e6b68630b 100644 --- a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h +++ b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_GT2560_REV_A_PLUS #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "RdW i3 Pro X" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1523,8 +1529,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1681,6 +1690,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1908,31 +1925,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1966,15 +1964,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1987,6 +1976,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2012,17 +2043,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2118,8 +2156,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Geeetech/MeCreator2/Configuration.h b/config/examples/Geeetech/MeCreator2/Configuration.h index 69ed2d490b..0c1b26a979 100644 --- a/config/examples/Geeetech/MeCreator2/Configuration.h +++ b/config/examples/Geeetech/MeCreator2/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_GT2560_V3_MC2 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "MeCreator2" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -518,7 +524,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //MeCreator2 generated by Autotune #define DEFAULT_bedKp 182.46 // 175.68 189.95 @@ -1530,8 +1536,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1688,6 +1697,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1915,31 +1932,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1973,15 +1971,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1994,6 +1983,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2019,17 +2050,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2125,8 +2163,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Geeetech/MeCreator2/Configuration_adv.h b/config/examples/Geeetech/MeCreator2/Configuration_adv.h index 96db80d419..7ab2818017 100644 --- a/config/examples/Geeetech/MeCreator2/Configuration_adv.h +++ b/config/examples/Geeetech/MeCreator2/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1363,6 +1368,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1748,6 +1756,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2433,6 +2444,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h index 43d7306b12..3189d8f61f 100644 --- a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_GT2560_REV_A_PLUS #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "i3 Pro B" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -524,7 +530,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //12v (120 watt?) MK2a PCB Heatbed into 4mm borosilicate (Geeetech Prusa i3 Pro, Pro/B/C/X) @@ -1544,8 +1550,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1702,6 +1711,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1929,31 +1946,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1987,15 +1985,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -2008,6 +1997,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2033,17 +2064,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2139,8 +2177,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h index 53597ea441..14a906937f 100644 --- a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_GT2560_REV_A_PLUS #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "i3 Pro B" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -524,7 +530,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //12v (120 watt?) MK2a PCB Heatbed into 4mm borosilicate (Geeetech Prusa i3 Pro, Pro/B/C/X) @@ -1543,8 +1549,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1701,6 +1710,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1928,31 +1945,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1986,15 +1984,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -2007,6 +1996,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2032,17 +2063,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2138,8 +2176,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h index 3fb2e1e5fa..d6994864d3 100644 --- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_GT2560_REV_A #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "i3 Pro C" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 1 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1523,8 +1529,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1681,6 +1690,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1908,31 +1925,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1966,15 +1964,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1987,6 +1976,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2012,17 +2043,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2118,8 +2156,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h index b9e680bc11..2a38b807d5 100644 --- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h +++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu #define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h index 4fcc8fc5bb..e455d5bc0d 100644 --- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_GT2560_REV_A_PLUS #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "i3 Pro W" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1523,8 +1529,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1681,6 +1690,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1908,31 +1925,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1966,15 +1964,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1987,6 +1976,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2012,17 +2043,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2118,8 +2156,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h index b9e680bc11..2a38b807d5 100644 --- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h +++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu #define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Infitary/i3-M508/Configuration.h b/config/examples/Infitary/i3-M508/Configuration.h index ecf3d1927b..aa1e198f97 100644 --- a/config/examples/Infitary/i3-M508/Configuration.h +++ b/config/examples/Infitary/i3-M508/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_RAMPS_13_EFB #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Infitary M508" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -518,7 +524,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1527,8 +1533,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1685,6 +1694,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1912,31 +1929,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1970,15 +1968,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1991,6 +1980,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2016,17 +2047,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2122,8 +2160,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Infitary/i3-M508/Configuration_adv.h b/config/examples/Infitary/i3-M508/Configuration_adv.h index 55bf70e5df..517515a545 100644 --- a/config/examples/Infitary/i3-M508/Configuration_adv.h +++ b/config/examples/Infitary/i3-M508/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/JGAurora/A1/Configuration.h b/config/examples/JGAurora/A1/Configuration.h index d6fe90c179..053a3244f9 100644 --- a/config/examples/JGAurora/A1/Configuration.h +++ b/config/examples/JGAurora/A1/Configuration.h @@ -73,9 +73,14 @@ // User-specified version info of this build to display in [Pronterface, etc] terminal window during // startup. Implementation of an idea by Prof Braino to inform user that any changes made to this // build by the user have been successfully uploaded into firmware. + +// ╦╔═╗╔═╗┬ ┬┬─┐┌─┐┬─┐┌─┐╔═╗┌─┐┬─┐┬ ┬┌┬┐ ┌─┐┌─┐┌┬┐ +// ║║ ╦╠═╣│ │├┬┘│ │├┬┘├─┤╠╣ │ │├┬┘│ ││││ │ │ ││││ +// ╚╝╚═╝╩ ╩└─┘┴└─└─┘┴└─┴ ┴╚ └─┘┴└─└─┘┴ ┴o└─┘└─┘┴ ┴ + #define STRING_CONFIG_H_AUTHOR "(Roberto Mariani & Samuel Pinches)" // Who made the changes. #define SHOW_BOOTSCREEN -#define STRING_SPLASH_LINE1 "Marlin 2b6 (10/6/19)" // will be shown during bootup in line 1 +#define STRING_SPLASH_LINE1 "JG-A1 v2.0 (29-7-19)" // will be shown during bootup in line 1 #define STRING_SPLASH_LINE2 "JGAuroraForum.com" // will be shown during bootup in line 2 /** @@ -129,18 +134,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_JGAURORA_A5S_A1 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "JGAurora A1" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +280,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +369,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +406,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -514,7 +525,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -719,7 +730,7 @@ * Override with M203 * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] */ -#define DEFAULT_MAX_FEEDRATE { 360, 150, 15, 25 } +#define DEFAULT_MAX_FEEDRATE { 360, 150, 30, 40 } /** * Default Max Acceleration (change/s) change = mm/s @@ -741,9 +752,15 @@ #define DEFAULT_RETRACT_ACCELERATION 500 // E acceleration for retracts #define DEFAULT_TRAVEL_ACCELERATION 500 // X, Y, Z acceleration for travel (non printing) moves -// -// Use Junction Deviation instead of traditional Jerk Limiting -// +/** + * Junction Deviation + * + * Use Junction Deviation instead of traditional Jerk Limiting + * + * See: + * https://reprap.org/forum/read.php?1,739819 + * http://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html + */ #define JUNCTION_DEVIATION #if ENABLED(JUNCTION_DEVIATION) #define JUNCTION_DEVIATION_MM 0.02 // (mm) Distance from real junction edge @@ -909,7 +926,7 @@ #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z // Feedrate (mm/m) for the "accurate" probe of each point -#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) +#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 4) /** * Multiple Probing @@ -1318,7 +1335,7 @@ #endif // Homing speeds (mm/m) -#define HOMING_FEEDRATE_XY (50*60) +#define HOMING_FEEDRATE_XY (90*60) #define HOMING_FEEDRATE_Z (12*60) // Validate that endstops are triggered on homing moves @@ -1519,8 +1536,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1678,6 +1698,14 @@ // #define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1905,31 +1933,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1963,15 +1972,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1984,6 +1984,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2009,17 +2051,26 @@ //============================================================================= // -// MKS Robin 320x240 color display -// Also used for JGAurora A5S & A1 TFT LCD's (16-bit Parallel LCD via FSMC) -#define MKS_ROBIN_TFT +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) +// +#define FSMC_GRAPHICAL_TFT +//#define PRINTER_EVENT_LEDS //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 + #define XPT2046_Z1_THRESHOLD 1 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2115,8 +2166,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/JGAurora/A1/Configuration_adv.h b/config/examples/JGAurora/A1/Configuration_adv.h index 46fc4740cd..49058c3f1c 100644 --- a/config/examples/JGAurora/A1/Configuration_adv.h +++ b/config/examples/JGAurora/A1/Configuration_adv.h @@ -306,7 +306,7 @@ * * Define one or both of these to override the default 0-255 range. */ -//#define FAN_MIN_PWM 50 +#define FAN_MIN_PWM 30 //#define FAN_MAX_PWM 128 /** @@ -522,9 +522,9 @@ #define X_HOME_BUMP_MM 5 #define Y_HOME_BUMP_MM 5 #define Z_HOME_BUMP_MM 2 -#define HOMING_BUMP_DIVISOR { 2, 2, 4 } // Re-Bump Speed Divisor (Divides the Homing Feedrate) -//#define QUICK_HOME // If homing includes X and Y, do a diagonal move initially -//#define HOMING_BACKOFF_MM { 2, 2, 2 } // (mm) Move away from the endstops after homing +#define HOMING_BUMP_DIVISOR { 5, 5, 5 } // Re-Bump Speed Divisor (Divides the Homing Feedrate) +#define QUICK_HOME // If homing includes X and Y, do a diagonal move initially +#define HOMING_BACKOFF_MM { 1, 1, 0 } // (mm) Move away from the endstops after homing // When G28 is called, this option will make Y home before X //#define HOME_Y_BEFORE_X @@ -654,7 +654,8 @@ // @section lcd #if EITHER(ULTIPANEL, EXTENSIBLE_UI) - #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define MANUAL_FEEDRATE { 60*60, 60*60, 10*60, 10*60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -856,15 +857,18 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view -//#define STATUS_MESSAGE_SCROLLING +#define STATUS_MESSAGE_SCROLLING // On the Info Screen, display XY with one decimal place when possible -//#define LCD_DECIMAL_SMALL_XY +#define LCD_DECIMAL_SMALL_XY // The timeout (in ms) to return to the status screen from sub-menus -//#define LCD_TIMEOUT_TO_STATUS 15000 +#define LCD_TIMEOUT_TO_STATUS 15000 // Add an 'M73' G-code to set the current percentage //#define LCD_SET_PROGRESS_MANUALLY @@ -884,16 +888,16 @@ * LED Control Menu * Enable this feature to add LED Control to the LCD menu */ -#define LED_CONTROL_MENU +//#define LED_CONTROL_MENU #if ENABLED(LED_CONTROL_MENU) #define LED_COLOR_PRESETS // Enable the Preset Color menu option #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 0 // User defined RED value - #define LED_USER_PRESET_GREEN 255 // User defined GREEN value - #define LED_USER_PRESET_BLUE 255 // User defined BLUE value + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value #define LED_USER_PRESET_WHITE 255 // User defined WHITE value #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - #define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup #endif #endif // LED_CONTROL_MENU @@ -904,7 +908,7 @@ // as SD_DETECT_PIN in your board's pins definitions. // This setting should be disabled unless you are using a push button, pulling the pin to ground. // Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER). - //#define SD_DETECT_INVERTED + #define SD_DETECT_INVERTED #define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place. @@ -978,10 +982,10 @@ #endif // This allows hosts to request long names for files and folders with M33 - //#define LONG_FILENAME_HOST_SUPPORT + #define LONG_FILENAME_HOST_SUPPORT // Enable this option to scroll long filenames in the SD card menu - //#define SCROLL_LONG_FILENAMES + #define SCROLL_LONG_FILENAMES // Leave the heaters on after Stop Print (not recommended!) //#define SD_ABORT_NO_COOLDOWN @@ -1042,7 +1046,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1077,13 +1081,13 @@ */ #if HAS_GRAPHICAL_LCD // Show SD percentage next to the progress bar - //#define DOGM_SD_PERCENT + #define DOGM_SD_PERCENT // Enable to save many cycles by drawing a hollow frame on the Info Screen - #define XYZ_HOLLOW_FRAME + //#define XYZ_HOLLOW_FRAME // Enable to save many cycles by drawing a hollow frame on Menu Screens - #define MENU_HOLLOW_FRAME + //#define MENU_HOLLOW_FRAME // A bigger font is available for edit items. Costs 3120 bytes of PROGMEM. // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. @@ -1133,13 +1137,14 @@ //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames - //#define STATUS_HEAT_PERCENT // Show heating in a progress bar + #define STATUS_HEAT_PERCENT // Show heating in a progress bar //#define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash) // Frivolous Game Options //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1179,14 +1184,14 @@ #if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING) #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds. // Note: Extra time may be added to mitigate controller latency. - //#define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement). - #define MOVE_Z_WHEN_IDLE // Jump to the move Z menu on doubleclick when printer is idle. + #define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement). + //#define MOVE_Z_WHEN_IDLE // Jump to the move Z menu on doubleclick when printer is idle. #if ENABLED(MOVE_Z_WHEN_IDLE) #define MOVE_Z_IDLE_MULTIPLICATOR 10 // Multiply 1mm by this factor for the move step size. #endif #endif - //#define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28 + #define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28 //#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping #if ENABLED(BABYSTEP_ZPROBE_OFFSET) @@ -1369,6 +1374,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1483,23 +1491,23 @@ * Requires NOZZLE_PARK_FEATURE. * This feature is required for the default FILAMENT_RUNOUT_SCRIPT. */ -//#define ADVANCED_PAUSE_FEATURE +#define ADVANCED_PAUSE_FEATURE #if ENABLED(ADVANCED_PAUSE_FEATURE) #define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate. #define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract. // This short retract is done immediately, before parking the nozzle. - #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast. + #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 40 // (mm/s) Unload filament feedrate. This can be pretty fast. #define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. - #define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload. + #define FILAMENT_CHANGE_UNLOAD_LENGTH 820 // (mm) The length of filament for a complete unload. // For Bowden, the full length of the tube and nozzle. // For direct drive, the full length of the nozzle. // Set to 0 for manual unloading. - #define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load. - #define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material. + #define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 40 // (mm/s) Slow move when starting load. + #define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 730 // (mm) Slow length, to allow time to insert material. // 0 to disable start loading and skip to fast load only #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast. #define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. - #define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle. + #define FILAMENT_CHANGE_FAST_LOAD_LENGTH 75 // (mm) Load length of filament, from extruder gear to nozzle. // For Bowden, the full length of the tube and nozzle. // For direct drive, the full length of the nozzle. //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted. @@ -1520,10 +1528,10 @@ #define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed. #define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change. - //#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change. + #define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change. //#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change - //#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu. + #define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu. //#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302) #endif @@ -1754,6 +1762,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2439,6 +2450,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/JGAurora/A5/Configuration.h b/config/examples/JGAurora/A5/Configuration.h index 777ccc93bb..f82b4e2dfc 100644 --- a/config/examples/JGAurora/A5/Configuration.h +++ b/config/examples/JGAurora/A5/Configuration.h @@ -134,18 +134,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_MKS_GEN_L #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "JGAurora A5" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -282,7 +280,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -364,6 +369,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -400,7 +406,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 15 // manual calibration of thermistor in JGAurora A5 hotend #define TEMP_SENSOR_1 0 @@ -524,7 +530,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1535,8 +1541,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1693,6 +1702,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1920,31 +1937,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1978,15 +1976,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1999,6 +1988,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2024,17 +2055,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2130,8 +2168,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/JGAurora/A5/Configuration_adv.h b/config/examples/JGAurora/A5/Configuration_adv.h index d2546f8192..e76d22ee3b 100644 --- a/config/examples/JGAurora/A5/Configuration_adv.h +++ b/config/examples/JGAurora/A5/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 80*60, 80*60, 12*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/JGAurora/A5S/Configuration.h b/config/examples/JGAurora/A5S/Configuration.h index c1a5f6de0d..e43088907f 100644 --- a/config/examples/JGAurora/A5S/Configuration.h +++ b/config/examples/JGAurora/A5S/Configuration.h @@ -73,9 +73,14 @@ // User-specified version info of this build to display in [Pronterface, etc] terminal window during // startup. Implementation of an idea by Prof Braino to inform user that any changes made to this // build by the user have been successfully uploaded into firmware. + +// ╦╔═╗╔═╗┬ ┬┬─┐┌─┐┬─┐┌─┐╔═╗┌─┐┬─┐┬ ┬┌┬┐ ┌─┐┌─┐┌┬┐ +// ║║ ╦╠═╣│ │├┬┘│ │├┬┘├─┤╠╣ │ │├┬┘│ ││││ │ │ ││││ +// ╚╝╚═╝╩ ╩└─┘┴└─└─┘┴└─┴ ┴╚ └─┘┴└─└─┘┴ ┴o└─┘└─┘┴ ┴ + #define STRING_CONFIG_H_AUTHOR "(Roberto Mariani & Samuel Pinches)" // Who made the changes. #define SHOW_BOOTSCREEN -#define STRING_SPLASH_LINE1 "Marlin 2b6 (10/6/19)" // will be shown during bootup in line 1 +#define STRING_SPLASH_LINE1 "JG-A5S v2.0 (29-7-19)" // will be shown during bootup in line 1 #define STRING_SPLASH_LINE2 "JGAuroraForum.com" // will be shown during bootup in line 2 /** @@ -129,18 +134,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_JGAURORA_A5S_A1 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "JGAurora A5S" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +280,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +369,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +406,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -514,7 +525,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -719,7 +730,7 @@ * Override with M203 * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] */ -#define DEFAULT_MAX_FEEDRATE { 360, 150, 15, 25 } +#define DEFAULT_MAX_FEEDRATE { 360, 150, 30, 40 } /** * Default Max Acceleration (change/s) change = mm/s @@ -741,9 +752,15 @@ #define DEFAULT_RETRACT_ACCELERATION 500 // E acceleration for retracts #define DEFAULT_TRAVEL_ACCELERATION 500 // X, Y, Z acceleration for travel (non printing) moves -// -// Use Junction Deviation instead of traditional Jerk Limiting -// +/** + * Junction Deviation + * + * Use Junction Deviation instead of traditional Jerk Limiting + * + * See: + * https://reprap.org/forum/read.php?1,739819 + * http://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html + */ #define JUNCTION_DEVIATION #if ENABLED(JUNCTION_DEVIATION) #define JUNCTION_DEVIATION_MM 0.02 // (mm) Distance from real junction edge @@ -909,7 +926,7 @@ #define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z // Feedrate (mm/m) for the "accurate" probe of each point -#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) +#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 4) /** * Multiple Probing @@ -1318,7 +1335,7 @@ #endif // Homing speeds (mm/m) -#define HOMING_FEEDRATE_XY (50*60) +#define HOMING_FEEDRATE_XY (90*60) #define HOMING_FEEDRATE_Z (12*60) // Validate that endstops are triggered on homing moves @@ -1519,8 +1536,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1678,6 +1698,14 @@ // #define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1905,31 +1933,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1963,15 +1972,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1984,6 +1984,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2009,18 +2051,26 @@ //============================================================================= // -// MKS Robin 320x240 color display -// Also used for JGAurora A5S & A1 TFT LCD's (16-bit Parallel LCD via FSMC) -#define MKS_ROBIN_TFT -#define PRINTER_EVENT_LEDS +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) +// +#define FSMC_GRAPHICAL_TFT +//#define PRINTER_EVENT_LEDS //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 + #define XPT2046_Z1_THRESHOLD 1 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2116,8 +2166,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/JGAurora/A5S/Configuration_adv.h b/config/examples/JGAurora/A5S/Configuration_adv.h index 46fc4740cd..49058c3f1c 100644 --- a/config/examples/JGAurora/A5S/Configuration_adv.h +++ b/config/examples/JGAurora/A5S/Configuration_adv.h @@ -306,7 +306,7 @@ * * Define one or both of these to override the default 0-255 range. */ -//#define FAN_MIN_PWM 50 +#define FAN_MIN_PWM 30 //#define FAN_MAX_PWM 128 /** @@ -522,9 +522,9 @@ #define X_HOME_BUMP_MM 5 #define Y_HOME_BUMP_MM 5 #define Z_HOME_BUMP_MM 2 -#define HOMING_BUMP_DIVISOR { 2, 2, 4 } // Re-Bump Speed Divisor (Divides the Homing Feedrate) -//#define QUICK_HOME // If homing includes X and Y, do a diagonal move initially -//#define HOMING_BACKOFF_MM { 2, 2, 2 } // (mm) Move away from the endstops after homing +#define HOMING_BUMP_DIVISOR { 5, 5, 5 } // Re-Bump Speed Divisor (Divides the Homing Feedrate) +#define QUICK_HOME // If homing includes X and Y, do a diagonal move initially +#define HOMING_BACKOFF_MM { 1, 1, 0 } // (mm) Move away from the endstops after homing // When G28 is called, this option will make Y home before X //#define HOME_Y_BEFORE_X @@ -654,7 +654,8 @@ // @section lcd #if EITHER(ULTIPANEL, EXTENSIBLE_UI) - #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define MANUAL_FEEDRATE { 60*60, 60*60, 10*60, 10*60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -856,15 +857,18 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view -//#define STATUS_MESSAGE_SCROLLING +#define STATUS_MESSAGE_SCROLLING // On the Info Screen, display XY with one decimal place when possible -//#define LCD_DECIMAL_SMALL_XY +#define LCD_DECIMAL_SMALL_XY // The timeout (in ms) to return to the status screen from sub-menus -//#define LCD_TIMEOUT_TO_STATUS 15000 +#define LCD_TIMEOUT_TO_STATUS 15000 // Add an 'M73' G-code to set the current percentage //#define LCD_SET_PROGRESS_MANUALLY @@ -884,16 +888,16 @@ * LED Control Menu * Enable this feature to add LED Control to the LCD menu */ -#define LED_CONTROL_MENU +//#define LED_CONTROL_MENU #if ENABLED(LED_CONTROL_MENU) #define LED_COLOR_PRESETS // Enable the Preset Color menu option #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 0 // User defined RED value - #define LED_USER_PRESET_GREEN 255 // User defined GREEN value - #define LED_USER_PRESET_BLUE 255 // User defined BLUE value + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value #define LED_USER_PRESET_WHITE 255 // User defined WHITE value #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - #define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup #endif #endif // LED_CONTROL_MENU @@ -904,7 +908,7 @@ // as SD_DETECT_PIN in your board's pins definitions. // This setting should be disabled unless you are using a push button, pulling the pin to ground. // Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER). - //#define SD_DETECT_INVERTED + #define SD_DETECT_INVERTED #define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place. @@ -978,10 +982,10 @@ #endif // This allows hosts to request long names for files and folders with M33 - //#define LONG_FILENAME_HOST_SUPPORT + #define LONG_FILENAME_HOST_SUPPORT // Enable this option to scroll long filenames in the SD card menu - //#define SCROLL_LONG_FILENAMES + #define SCROLL_LONG_FILENAMES // Leave the heaters on after Stop Print (not recommended!) //#define SD_ABORT_NO_COOLDOWN @@ -1042,7 +1046,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1077,13 +1081,13 @@ */ #if HAS_GRAPHICAL_LCD // Show SD percentage next to the progress bar - //#define DOGM_SD_PERCENT + #define DOGM_SD_PERCENT // Enable to save many cycles by drawing a hollow frame on the Info Screen - #define XYZ_HOLLOW_FRAME + //#define XYZ_HOLLOW_FRAME // Enable to save many cycles by drawing a hollow frame on Menu Screens - #define MENU_HOLLOW_FRAME + //#define MENU_HOLLOW_FRAME // A bigger font is available for edit items. Costs 3120 bytes of PROGMEM. // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. @@ -1133,13 +1137,14 @@ //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames - //#define STATUS_HEAT_PERCENT // Show heating in a progress bar + #define STATUS_HEAT_PERCENT // Show heating in a progress bar //#define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash) // Frivolous Game Options //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1179,14 +1184,14 @@ #if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING) #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds. // Note: Extra time may be added to mitigate controller latency. - //#define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement). - #define MOVE_Z_WHEN_IDLE // Jump to the move Z menu on doubleclick when printer is idle. + #define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement). + //#define MOVE_Z_WHEN_IDLE // Jump to the move Z menu on doubleclick when printer is idle. #if ENABLED(MOVE_Z_WHEN_IDLE) #define MOVE_Z_IDLE_MULTIPLICATOR 10 // Multiply 1mm by this factor for the move step size. #endif #endif - //#define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28 + #define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28 //#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping #if ENABLED(BABYSTEP_ZPROBE_OFFSET) @@ -1369,6 +1374,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1483,23 +1491,23 @@ * Requires NOZZLE_PARK_FEATURE. * This feature is required for the default FILAMENT_RUNOUT_SCRIPT. */ -//#define ADVANCED_PAUSE_FEATURE +#define ADVANCED_PAUSE_FEATURE #if ENABLED(ADVANCED_PAUSE_FEATURE) #define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate. #define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract. // This short retract is done immediately, before parking the nozzle. - #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast. + #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 40 // (mm/s) Unload filament feedrate. This can be pretty fast. #define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. - #define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload. + #define FILAMENT_CHANGE_UNLOAD_LENGTH 820 // (mm) The length of filament for a complete unload. // For Bowden, the full length of the tube and nozzle. // For direct drive, the full length of the nozzle. // Set to 0 for manual unloading. - #define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load. - #define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material. + #define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 40 // (mm/s) Slow move when starting load. + #define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 730 // (mm) Slow length, to allow time to insert material. // 0 to disable start loading and skip to fast load only #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast. #define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. - #define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle. + #define FILAMENT_CHANGE_FAST_LOAD_LENGTH 75 // (mm) Load length of filament, from extruder gear to nozzle. // For Bowden, the full length of the tube and nozzle. // For direct drive, the full length of the nozzle. //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted. @@ -1520,10 +1528,10 @@ #define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed. #define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change. - //#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change. + #define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change. //#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change - //#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu. + #define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu. //#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302) #endif @@ -1754,6 +1762,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2439,6 +2450,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/MakerParts/Configuration.h b/config/examples/MakerParts/Configuration.h index 8a36536bae..ba234227e3 100644 --- a/config/examples/MakerParts/Configuration.h +++ b/config/examples/MakerParts/Configuration.h @@ -149,18 +149,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_RAMPS_DUO_EFB #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "MakerParts 3D Printer" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 #define MACHINE_UUID "4250d842-4943-4601-acca-95ef77b8a4f1" // @section extruder @@ -297,7 +295,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -379,6 +384,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -415,7 +421,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -534,7 +540,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1543,8 +1549,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1701,6 +1710,14 @@ // #define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1928,31 +1945,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1986,15 +1984,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -2007,6 +1996,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2032,17 +2063,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2138,8 +2176,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/MakerParts/Configuration_adv.h b/config/examples/MakerParts/Configuration_adv.h index 2eb03a3ea6..fd569ee4be 100644 --- a/config/examples/MakerParts/Configuration_adv.h +++ b/config/examples/MakerParts/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu #define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ #define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Malyan/M150/Configuration.h b/config/examples/Malyan/M150/Configuration.h index 6b3bab02ea..8cbee7e927 100644 --- a/config/examples/Malyan/M150/Configuration.h +++ b/config/examples/Malyan/M150/Configuration.h @@ -134,18 +134,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_MELZI_MALYAN #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Malyan M150" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 #define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -282,7 +280,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -364,6 +369,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -400,7 +406,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -522,7 +528,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1551,8 +1557,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1709,6 +1718,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1936,31 +1953,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1994,15 +1992,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -2015,6 +2004,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2040,17 +2071,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2146,8 +2184,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Malyan/M150/Configuration_adv.h b/config/examples/Malyan/M150/Configuration_adv.h index 62164ca374..ae1c868768 100644 --- a/config/examples/Malyan/M150/Configuration_adv.h +++ b/config/examples/Malyan/M150/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Malyan/M200/Configuration.h b/config/examples/Malyan/M200/Configuration.h index dedb485e16..dd401763ea 100644 --- a/config/examples/Malyan/M200/Configuration.h +++ b/config/examples/Malyan/M200/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_MALYAN_M200 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Malyan M200" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 11 #define TEMP_SENSOR_1 0 @@ -513,7 +519,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1522,8 +1528,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1680,6 +1689,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1907,31 +1924,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1965,15 +1963,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1986,6 +1975,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2011,9 +2042,9 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ @@ -2029,8 +2060,15 @@ #define MALYAN_LCD // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2126,8 +2164,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Malyan/M200/Configuration_adv.h b/config/examples/Malyan/M200/Configuration_adv.h index 9b992ab431..f903908026 100644 --- a/config/examples/Malyan/M200/Configuration_adv.h +++ b/config/examples/Malyan/M200/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Micromake/C1/basic/Configuration.h b/config/examples/Micromake/C1/basic/Configuration.h index 936fd72929..3c76d0aa10 100644 --- a/config/examples/Micromake/C1/basic/Configuration.h +++ b/config/examples/Micromake/C1/basic/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_MAKEBOARD_MINI #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Micromake C1" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1527,8 +1533,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1685,6 +1694,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1912,31 +1929,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1970,15 +1968,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1991,6 +1980,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2016,17 +2047,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2122,8 +2160,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Micromake/C1/enhanced/Configuration.h b/config/examples/Micromake/C1/enhanced/Configuration.h index e16c1ba62d..0b0f6a19ab 100644 --- a/config/examples/Micromake/C1/enhanced/Configuration.h +++ b/config/examples/Micromake/C1/enhanced/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_MAKEBOARD_MINI #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Micromake C1" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1527,8 +1533,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1685,6 +1694,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1912,31 +1929,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1970,15 +1968,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1991,6 +1980,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2016,17 +2047,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2122,8 +2160,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Micromake/C1/enhanced/Configuration_adv.h b/config/examples/Micromake/C1/enhanced/Configuration_adv.h index 912af92621..b626b9086c 100644 --- a/config/examples/Micromake/C1/enhanced/Configuration_adv.h +++ b/config/examples/Micromake/C1/enhanced/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Mks/Robin/Configuration.h b/config/examples/Mks/Robin/Configuration.h index 96a6bb7fbd..4023914af9 100644 --- a/config/examples/Mks/Robin/Configuration.h +++ b/config/examples/Mks/Robin/Configuration.h @@ -130,18 +130,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_MKS_ROBIN #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "MKS Robin" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -278,7 +276,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -360,6 +365,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -396,7 +402,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 1 @@ -515,7 +521,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1524,8 +1530,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1683,6 +1692,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1910,31 +1927,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1968,15 +1966,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1989,6 +1978,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2014,17 +2045,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -#define MKS_ROBIN_TFT +#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2120,8 +2158,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Mks/Robin/Configuration_adv.h b/config/examples/Mks/Robin/Configuration_adv.h index 354fcb95c3..c0d42d1b2e 100644 --- a/config/examples/Mks/Robin/Configuration_adv.h +++ b/config/examples/Mks/Robin/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Mks/Sbase/Configuration.h b/config/examples/Mks/Sbase/Configuration.h index f004854d6c..caf7dd853c 100644 --- a/config/examples/Mks/Sbase/Configuration.h +++ b/config/examples/Mks/Sbase/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_MKS_SBASE #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu //#define CUSTOM_MACHINE_NAME "3D Printer" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1523,8 +1529,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1681,6 +1690,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1908,31 +1925,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1966,15 +1964,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1987,6 +1976,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2012,17 +2043,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2118,8 +2156,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Mks/Sbase/Configuration_adv.h b/config/examples/Mks/Sbase/Configuration_adv.h index 7f21aef03e..64f2018aac 100644 --- a/config/examples/Mks/Sbase/Configuration_adv.h +++ b/config/examples/Mks/Sbase/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -852,6 +853,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1038,7 +1042,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1136,6 +1140,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1365,6 +1370,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1750,6 +1758,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2435,6 +2446,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Printrbot/PrintrboardG2/Configuration.h b/config/examples/Printrbot/PrintrboardG2/Configuration.h index 7dbe27cd27..b275a3b66b 100644 --- a/config/examples/Printrbot/PrintrboardG2/Configuration.h +++ b/config/examples/Printrbot/PrintrboardG2/Configuration.h @@ -130,18 +130,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_PRINTRBOARD_G2 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu //#define CUSTOM_MACHINE_NAME "3D Printer" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -278,7 +276,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -360,6 +365,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -396,7 +402,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -515,7 +521,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1531,8 +1537,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1689,6 +1698,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1916,31 +1933,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1974,15 +1972,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1995,6 +1984,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2020,17 +2051,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2128,6 +2166,8 @@ #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) #define NEOPIXEL_PIN 20 // LED driving pin #define NEOPIXEL_PIXELS 3 // Number of LEDs in the strip + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) #define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/RapideLite/RL200/Configuration.h b/config/examples/RapideLite/RL200/Configuration.h index ded24473d2..6cc23c2d9a 100644 --- a/config/examples/RapideLite/RL200/Configuration.h +++ b/config/examples/RapideLite/RL200/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_RL200 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Rapide Lite 200" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1523,8 +1529,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1681,6 +1690,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1908,31 +1925,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1966,15 +1964,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1987,6 +1976,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2012,17 +2043,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2118,8 +2156,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/RapideLite/RL200/Configuration_adv.h b/config/examples/RapideLite/RL200/Configuration_adv.h index ab597a258b..945799092a 100644 --- a/config/examples/RapideLite/RL200/Configuration_adv.h +++ b/config/examples/RapideLite/RL200/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/RepRapPro/Huxley/Configuration.h b/config/examples/RepRapPro/Huxley/Configuration.h index 11f5e394ab..8cd2a65c16 100644 --- a/config/examples/RepRapPro/Huxley/Configuration.h +++ b/config/examples/RepRapPro/Huxley/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_SANGUINOLOLU_12 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Huxley" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1572,8 +1578,11 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1730,6 +1739,14 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1957,31 +1974,12 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -2015,15 +2013,6 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -2036,6 +2025,48 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2061,17 +2092,24 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2167,8 +2205,10 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/RepRapWorld/Megatronics/Configuration.h b/config/examples/RepRapWorld/Megatronics/Configuration.h index 354f62b614..2c0b9a370b 100644 --- a/config/examples/RepRapWorld/Megatronics/Configuration.h +++ b/config/examples/RepRapWorld/Megatronics/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_MEGATRONICS_3 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu //#define CUSTOM_MACHINE_NAME "3D Printer" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1523,8 +1529,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1681,6 +1690,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1908,31 +1925,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1966,15 +1964,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1987,6 +1976,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2012,17 +2043,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2118,8 +2156,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/RigidBot/Configuration.h b/config/examples/RigidBot/Configuration.h index 74db97820b..a9bd044793 100644 --- a/config/examples/RigidBot/Configuration.h +++ b/config/examples/RigidBot/Configuration.h @@ -129,8 +129,7 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup // for Rigidbot version 1 : #define MOTHERBOARD BOARD_RIGIDBOARD // for Rigidbot Version 2 : #define MOTHERBOARD BOARD_RIGIDBOARD_V2 @@ -138,12 +137,11 @@ #define MOTHERBOARD BOARD_RIGIDBOARD_V2 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Rigidbot" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -280,7 +278,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -362,6 +367,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -398,7 +404,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 // DGlass3D = 5; RigidBot = 1; 3DSv6 = 5 #define TEMP_SENSOR_1 0 @@ -517,7 +523,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //RigidBot, from pid autotune @@ -1521,8 +1527,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1679,6 +1688,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1908,31 +1925,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1966,15 +1964,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1987,6 +1976,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2012,17 +2043,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2118,8 +2156,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/RigidBot/Configuration_adv.h b/config/examples/RigidBot/Configuration_adv.h index b3c2379d58..cd26628da8 100644 --- a/config/examples/RigidBot/Configuration_adv.h +++ b/config/examples/RigidBot/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/SCARA/Configuration.h b/config/examples/SCARA/Configuration.h index a563b4e2d6..86f48f33c7 100644 --- a/config/examples/SCARA/Configuration.h +++ b/config/examples/SCARA/Configuration.h @@ -156,18 +156,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_RAMPS_14_EFB #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "SCARA" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -304,7 +302,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -386,6 +391,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -422,7 +428,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -529,7 +535,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //12v Heatbed Mk3 12V in parallel @@ -1532,8 +1538,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1690,6 +1699,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1917,31 +1934,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1975,15 +1973,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1996,6 +1985,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2021,17 +2052,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2127,8 +2165,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/SCARA/Configuration_adv.h b/config/examples/SCARA/Configuration_adv.h index 3a47fef12f..c49df847f1 100644 --- a/config/examples/SCARA/Configuration_adv.h +++ b/config/examples/SCARA/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 10*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration.h b/config/examples/STM32/Black_STM32F407VET6/Configuration.h index 706db8c9a2..61dc961557 100644 --- a/config/examples/STM32/Black_STM32F407VET6/Configuration.h +++ b/config/examples/STM32/Black_STM32F407VET6/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_BLACK_STM32F407VE #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu //#define CUSTOM_MACHINE_NAME "3D Printer" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 1 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1523,8 +1529,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1681,6 +1690,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1908,31 +1925,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1966,15 +1964,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1987,6 +1976,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2012,17 +2043,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2118,8 +2156,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h index 9af92091bd..efd24bd1f8 100644 --- a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h +++ b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/STM32/STM32F10/Configuration.h b/config/examples/STM32/STM32F10/Configuration.h index 6e2a08abc8..4f5f440408 100644 --- a/config/examples/STM32/STM32F10/Configuration.h +++ b/config/examples/STM32/STM32F10/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_STM32F1R #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "CTC i3 Pro B" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #warning temp_sensor set to 998/999 (fake) #define TEMP_SENSOR_0 999 @@ -515,7 +521,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1525,8 +1531,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1683,6 +1692,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1910,31 +1927,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1968,15 +1966,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1989,6 +1978,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2014,17 +2045,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2120,8 +2158,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/STM32/STM32F4/Configuration.h b/config/examples/STM32/STM32F4/Configuration.h index 92715a362c..5e296dc006 100644 --- a/config/examples/STM32/STM32F4/Configuration.h +++ b/config/examples/STM32/STM32F4/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_STM32F4 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu //#define CUSTOM_MACHINE_NAME "3D Printer" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1523,8 +1529,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1681,6 +1690,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1908,31 +1925,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1966,15 +1964,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1987,6 +1976,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2012,17 +2043,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2118,8 +2156,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/STM32/stm32f103ret6/Configuration.h b/config/examples/STM32/stm32f103ret6/Configuration.h index 607ca8cb4b..db11bdd61b 100644 --- a/config/examples/STM32/stm32f103ret6/Configuration.h +++ b/config/examples/STM32/stm32f103ret6/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_STM32F1R #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "CTC i3 Pro B" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #warning temp_sensor set to 998/999 (fake) #define TEMP_SENSOR_0 999 @@ -515,7 +521,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1525,8 +1531,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1683,6 +1692,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1910,31 +1927,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1968,15 +1966,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1989,6 +1978,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2014,17 +2045,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2120,8 +2158,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Sanguinololu/Configuration.h b/config/examples/Sanguinololu/Configuration.h index 38746e2b7d..db3677f39b 100644 --- a/config/examples/Sanguinololu/Configuration.h +++ b/config/examples/Sanguinololu/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_SANGUINOLOLU_12 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Sanguinololu" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1554,8 +1560,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1712,6 +1721,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1939,31 +1956,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1997,15 +1995,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -2018,6 +2007,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2043,17 +2074,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2149,8 +2187,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Sanguinololu/Configuration_adv.h b/config/examples/Sanguinololu/Configuration_adv.h index 27fcf3d2dc..4a376efc11 100644 --- a/config/examples/Sanguinololu/Configuration_adv.h +++ b/config/examples/Sanguinololu/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Tevo/Michelangelo/Configuration.h b/config/examples/Tevo/Michelangelo/Configuration.h new file mode 100644 index 0000000000..bde22531df --- /dev/null +++ b/config/examples/Tevo/Michelangelo/Configuration.h @@ -0,0 +1,2215 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Configuration.h + * + * Basic settings such as: + * + * - Type of electronics + * - Type of temperature sensor + * - Printer geometry + * - Endstop configuration + * - LCD controller + * - Extra features + * + * Advanced settings can be found in Configuration_adv.h + * + */ +#define CONFIGURATION_H_VERSION 020000 + +//=========================================================================== +//============================= Getting Started ============================= +//=========================================================================== + +/** + * Here are some standard links for getting your machine calibrated: + * + * http://reprap.org/wiki/Calibration + * http://youtu.be/wAL9d7FgInk + * http://calculator.josefprusa.cz + * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide + * http://www.thingiverse.com/thing:5573 + * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap + * http://www.thingiverse.com/thing:298812 + */ + +//=========================================================================== +//============================= DELTA Printer =============================== +//=========================================================================== +// For a Delta printer start with one of the configuration files in the +// config/examples/delta directory and customize for your machine. +// + +//=========================================================================== +//============================= SCARA Printer =============================== +//=========================================================================== +// For a SCARA printer start with the configuration files in +// config/examples/SCARA and customize for your machine. +// + +// @section info + +// User-specified version info of this build to display in [Pronterface, etc] terminal window during +// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this +// build by the user have been successfully uploaded into firmware. +#define STRING_CONFIG_H_AUTHOR "(thisiskeithb, Tevo Michelangelo)" // Who made the changes. +#define SHOW_BOOTSCREEN +#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1 +#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2 + +/** + * *** VENDORS PLEASE READ *** + * + * Marlin allows you to add a custom boot image for Graphical LCDs. + * With this option Marlin will first show your custom screen followed + * by the standard Marlin logo with version number and web URL. + * + * We encourage you to take advantage of this new feature and we also + * respectfully request that you retain the unmodified Marlin boot screen. + */ + +// Enable to show the bitmap in Marlin/_Bootscreen.h on startup. +#define SHOW_CUSTOM_BOOTSCREEN + +// Enable to show the bitmap in Marlin/_Statusscreen.h on the status screen. +//#define CUSTOM_STATUS_SCREEN_IMAGE + +// @section machine + +/** + * Select the serial port on the board to use for communication with the host. + * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. + * + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] + */ +#define SERIAL_PORT 0 + +/** + * Select a secondary serial port on the board to use for communication with the host. + * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. + * + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] + */ +//#define SERIAL_PORT_2 -1 + +/** + * This setting determines the communication speed of the printer. + * + * 250000 works in most cases, but you might try a lower speed if + * you commonly experience drop-outs during host printing. + * You may try up to 1000000 to speed up SD file transfer. + * + * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000] + */ +#define BAUDRATE 250000 + +// Enable the Bluetooth serial interface on AT90USB devices +//#define BLUETOOTH + +// Choose the name from boards.h that matches your setup +#ifndef MOTHERBOARD + #define MOTHERBOARD BOARD_MKS_GEN_L +#endif + +// Name displayed in the LCD "Ready" message and Info menu +#define CUSTOM_MACHINE_NAME "Michelangelo" + +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 +//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" + +// @section extruder + +// This defines the number of extruders +// :[1, 2, 3, 4, 5, 6] +#define EXTRUDERS 1 + +// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc. +#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 + +// For Cyclops or any "multi-extruder" that shares a single nozzle. +//#define SINGLENOZZLE + +/** + * Průša MK2 Single Nozzle Multi-Material Multiplexer, and variants. + * + * This device allows one stepper driver on a control board to drive + * two to eight stepper motors, one at a time, in a manner suitable + * for extruders. + * + * This option only allows the multiplexer to switch on tool-change. + * Additional options to configure custom E moves are pending. + */ +//#define MK2_MULTIPLEXER +#if ENABLED(MK2_MULTIPLEXER) + // Override the default DIO selector pins here, if needed. + // Some pins files may provide defaults for these pins. + //#define E_MUX0_PIN 40 // Always Required + //#define E_MUX1_PIN 42 // Needed for 3 to 8 inputs + //#define E_MUX2_PIN 44 // Needed for 5 to 8 inputs +#endif + +/** + * Prusa Multi-Material Unit v2 + * + * Requires NOZZLE_PARK_FEATURE to park print head in case MMU unit fails. + * Requires EXTRUDERS = 5 + * + * For additional configuration see Configuration_adv.h + */ +//#define PRUSA_MMU2 + +// A dual extruder that uses a single stepper motor +//#define SWITCHING_EXTRUDER +#if ENABLED(SWITCHING_EXTRUDER) + #define SWITCHING_EXTRUDER_SERVO_NR 0 + #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3] + #if EXTRUDERS > 3 + #define SWITCHING_EXTRUDER_E23_SERVO_NR 1 + #endif +#endif + +// A dual-nozzle that uses a servomotor to raise/lower one (or both) of the nozzles +//#define SWITCHING_NOZZLE +#if ENABLED(SWITCHING_NOZZLE) + #define SWITCHING_NOZZLE_SERVO_NR 0 + //#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second + #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo) +#endif + +/** + * Two separate X-carriages with extruders that connect to a moving part + * via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN. + */ +//#define PARKING_EXTRUDER + +/** + * Two separate X-carriages with extruders that connect to a moving part + * via a magnetic docking mechanism using movements and no solenoid + * + * project : https://www.thingiverse.com/thing:3080893 + * movements : https://youtu.be/0xCEiG9VS3k + * https://youtu.be/Bqbcs0CU2FE + */ +//#define MAGNETIC_PARKING_EXTRUDER + +#if EITHER(PARKING_EXTRUDER, MAGNETIC_PARKING_EXTRUDER) + + #define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders + #define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder + //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381 + + #if ENABLED(PARKING_EXTRUDER) + + #define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage + #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil + #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined. + //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381 + + #elif ENABLED(MAGNETIC_PARKING_EXTRUDER) + + #define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point + #define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple + #define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point + #define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling + + #endif + +#endif + +/** + * Switching Toolhead + * + * Support for swappable and dockable toolheads, such as + * the E3D Tool Changer. Toolheads are locked with a servo. + */ +//#define SWITCHING_TOOLHEAD + +/** + * Magnetic Switching Toolhead + * + * Support swappable and dockable toolheads with a magnetic + * docking mechanism using movement and no servo. + */ +//#define MAGNETIC_SWITCHING_TOOLHEAD + +/** + * Electromagnetic Switching Toolhead + * + * Parking for CoreXY / HBot kinematics. + * Toolheads are parked at one edge and held with an electromagnet. + * Supports more than 2 Toolheads. See https://youtu.be/JolbsAKTKf4 + */ +//#define ELECTROMAGNETIC_SWITCHING_TOOLHEAD + +#if ANY(SWITCHING_TOOLHEAD, MAGNETIC_SWITCHING_TOOLHEAD, ELECTROMAGNETIC_SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_Y_POS 235 // (mm) Y position of the toolhead dock + #define SWITCHING_TOOLHEAD_Y_SECURITY 10 // (mm) Security distance Y axis + #define SWITCHING_TOOLHEAD_Y_CLEAR 60 // (mm) Minimum distance from dock for unobstructed X axis + #define SWITCHING_TOOLHEAD_X_POS { 215, 0 } // (mm) X positions for parking the extruders + #if ENABLED(SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_SERVO_NR 2 // Index of the servo connector + #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock + #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif + #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching + #endif +#endif + +/** + * "Mixing Extruder" + * - Adds G-codes M163 and M164 to set and "commit" the current mix factors. + * - Extends the stepping routines to move multiple steppers in proportion to the mix. + * - Optional support for Repetier Firmware's 'M164 S' supporting virtual tools. + * - This implementation supports up to two mixing extruders. + * - Enable DIRECT_MIXING_IN_G1 for M165 and mixing in G1 (from Pia Taubert's reference implementation). + */ +//#define MIXING_EXTRUDER +#if ENABLED(MIXING_EXTRUDER) + #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder + #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164 + //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands + //#define GRADIENT_MIX // Support for gradient mixing with M166 and LCD + #if ENABLED(GRADIENT_MIX) + //#define GRADIENT_VTOOL // Add M166 T to use a V-tool index as a Gradient alias + #endif +#endif + +// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). +// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). +// For the other hotends it is their distance from the extruder 0 hotend. +//#define HOTEND_OFFSET_X { 0.0, 20.00 } // (mm) relative X-offset for each nozzle +//#define HOTEND_OFFSET_Y { 0.0, 5.00 } // (mm) relative Y-offset for each nozzle +//#define HOTEND_OFFSET_Z { 0.0, 0.00 } // (mm) relative Z-offset for each nozzle + +// @section machine + +/** + * Power Supply Control + * + * Enable and connect the power supply to the PS_ON_PIN. + * Specify whether the power supply is active HIGH or active LOW. + */ +//#define PSU_CONTROL +//#define PSU_NAME "Power Supply" + +#if ENABLED(PSU_CONTROL) + #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2) + + //#define PS_DEFAULT_OFF // Keep power off until enabled directly with M80 + + //#define AUTO_POWER_CONTROL // Enable automatic control of the PS_ON pin + #if ENABLED(AUTO_POWER_CONTROL) + #define AUTO_POWER_FANS // Turn on PSU if fans need power + #define AUTO_POWER_E_FANS + #define AUTO_POWER_CONTROLLERFAN + #define AUTO_POWER_CHAMBER_FAN + //#define AUTO_POWER_E_TEMP 50 // (°C) Turn on PSU over this temperature + //#define AUTO_POWER_CHAMBER_TEMP 30 // (°C) Turn on PSU over this temperature + #define POWER_TIMEOUT 30 + #endif +#endif + +// @section temperature + +//=========================================================================== +//============================= Thermal Settings ============================ +//=========================================================================== + +/** + * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table + * + * Temperature sensors available: + * + * -4 : thermocouple with AD8495 + * -3 : thermocouple with MAX31855 (only for sensor 0) + * -2 : thermocouple with MAX6675 (only for sensor 0) + * -1 : thermocouple with AD595 + * 0 : not used + * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 3 : Mendel-parts thermistor (4.7k pullup) + * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! + * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) + * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) + * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) + * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) + * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) + * 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) + * 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) + * 10 : 100k RS thermistor 198-961 (4.7k pullup) + * 11 : 100k beta 3950 1% thermistor (4.7k pullup) + * 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) + * 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" + * 15 : 100k thermistor calibration for JGAurora A5 hotend + * 18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327 + * 20 : the PT100 circuit found in the Ultimainboard V2.x + * 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 + * 61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup + * 66 : 4.7M High Temperature thermistor from Dyze Design + * 67 : 450C thermistor from SliceEngineering + * 70 : the 100K thermistor found in the bq Hephestos 2 + * 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor + * + * 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k. + * (but gives greater accuracy and more stable PID) + * 51 : 100k thermistor - EPCOS (1k pullup) + * 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup) + * 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) + * + * 1047 : Pt1000 with 4k7 pullup + * 1010 : Pt1000 with 1k pullup (non standard) + * 147 : Pt100 with 4k7 pullup + * 110 : Pt100 with 1k pullup (non standard) + * + * 1000 : Custom - Specify parameters in Configuration_adv.h + * + * Use these for Testing or Development purposes. NEVER for production machine. + * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. + * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. + * + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + */ +#define TEMP_SENSOR_0 1 +#define TEMP_SENSOR_1 0 +#define TEMP_SENSOR_2 0 +#define TEMP_SENSOR_3 0 +#define TEMP_SENSOR_4 0 +#define TEMP_SENSOR_5 0 +#define TEMP_SENSOR_BED 0 +#define TEMP_SENSOR_CHAMBER 0 + +// Dummy thermistor constant temperature readings, for use with 998 and 999 +#define DUMMY_THERMISTOR_998_VALUE 25 +#define DUMMY_THERMISTOR_999_VALUE 100 + +// Use temp sensor 1 as a redundant sensor with sensor 0. If the readings +// from the two sensors differ too much the print will be aborted. +//#define TEMP_SENSOR_1_AS_REDUNDANT +#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 + +#define TEMP_RESIDENCY_TIME 5 // (seconds) Time to wait for hotend to "settle" in M109 +#define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer +#define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target + +#define TEMP_BED_RESIDENCY_TIME 5 // (seconds) Time to wait for bed to "settle" in M190 +#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer +#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target + +// Below this temperature the heater will be switched off +// because it probably indicates a broken thermistor wire. +#define HEATER_0_MINTEMP 5 +#define HEATER_1_MINTEMP 5 +#define HEATER_2_MINTEMP 5 +#define HEATER_3_MINTEMP 5 +#define HEATER_4_MINTEMP 5 +#define HEATER_5_MINTEMP 5 +#define BED_MINTEMP 5 + +// Above this temperature the heater will be switched off. +// This can protect components from overheating, but NOT from shorts and failures. +// (Use MINTEMP for thermistor short/failure protection.) +#define HEATER_0_MAXTEMP 285 +#define HEATER_1_MAXTEMP 275 +#define HEATER_2_MAXTEMP 275 +#define HEATER_3_MAXTEMP 275 +#define HEATER_4_MAXTEMP 275 +#define HEATER_5_MAXTEMP 275 +#define BED_MAXTEMP 150 + +//=========================================================================== +//============================= PID Settings ================================ +//=========================================================================== +// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning + +// Comment the following line to disable PID and enable bang-bang. +#define PIDTEMP +#define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current +#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current +#define PID_K1 0.95 // Smoothing factor within any PID loop +#if ENABLED(PIDTEMP) + #define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM) + #define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM) + //#define PID_DEBUG // Sends debug data to the serial port. + //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX + //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay + //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] + #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature + // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. + + // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it + +// Tevo Michelangelo + #define DEFAULT_Kp 19.71 + #define DEFAULT_Ki 1.39 + #define DEFAULT_Kd 69.81 + + // Ultimaker + //#define DEFAULT_Kp 22.2 + //#define DEFAULT_Ki 1.08 + //#define DEFAULT_Kd 114 + + // MakerGear + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 + + // Mendel Parts V9 on 12V + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 + +#endif // PIDTEMP + +//=========================================================================== +//====================== PID > Bed Temperature Control ====================== +//=========================================================================== + +/** + * PID Bed Heating + * + * If this option is enabled set PID constants below. + * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis. + * + * The PID frequency will be the same as the extruder PWM. + * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz, + * which is fine for driving a square wave into a resistive load and does not significantly + * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W + * heater. If your configuration is significantly different than this and you don't understand + * the issues involved, don't use bed PID until someone else verifies that your hardware works. + */ +//#define PIDTEMPBED + +//#define BED_LIMIT_SWITCHING + +/** + * Max Bed Power + * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis). + * When set to any value below 255, enables a form of PWM to the bed that acts like a divider + * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED) + */ +#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current + +#if ENABLED(PIDTEMPBED) + //#define MIN_BED_POWER 0 + //#define PID_BED_DEBUG // Sends debug data to the serial port. + + //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) + //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 + + //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) + //from pidautotune + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 + + // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. +#endif // PIDTEMPBED + +// @section extruder + +/** + * Prevent extrusion if the temperature is below EXTRUDE_MINTEMP. + * Add M302 to set the minimum extrusion temperature and/or turn + * cold extrusion prevention on and off. + * + * *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! *** + */ +#define PREVENT_COLD_EXTRUSION +#define EXTRUDE_MINTEMP 170 + +/** + * Prevent a single extrusion longer than EXTRUDE_MAXLENGTH. + * Note: For Bowden Extruders make this large enough to allow load/unload. + */ +#define PREVENT_LENGTHY_EXTRUDE +#define EXTRUDE_MAXLENGTH 300 + +//=========================================================================== +//======================== Thermal Runaway Protection ======================= +//=========================================================================== + +/** + * Thermal Protection provides additional protection to your printer from damage + * and fire. Marlin always includes safe min and max temperature ranges which + * protect against a broken or disconnected thermistor wire. + * + * The issue: If a thermistor falls out, it will report the much lower + * temperature of the air in the room, and the the firmware will keep + * the heater on. + * + * If you get "Thermal Runaway" or "Heating failed" errors the + * details can be tuned in Configuration_adv.h + */ + +#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders +#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed +#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber + +//=========================================================================== +//============================= Mechanical Settings ========================= +//=========================================================================== + +// @section machine + +// Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics +// either in the usual order or reversed +//#define COREXY +//#define COREXZ +//#define COREYZ +//#define COREYX +//#define COREZX +//#define COREZY + +//=========================================================================== +//============================== Endstop Settings =========================== +//=========================================================================== + +// @section homing + +// Specify here all the endstop connectors that are connected to any endstop or probe. +// Almost all printers will be using one per axis. Probes will use one or more of the +// extra connectors. Leave undefined any used for non-endstop and non-probe purposes. +#define USE_XMIN_PLUG +#define USE_YMIN_PLUG +#define USE_ZMIN_PLUG +//#define USE_XMAX_PLUG +//#define USE_YMAX_PLUG +//#define USE_ZMAX_PLUG + +// Enable pullup for all endstops to prevent a floating state +#define ENDSTOPPULLUPS +#if DISABLED(ENDSTOPPULLUPS) + // Disable ENDSTOPPULLUPS to set pullups individually + //#define ENDSTOPPULLUP_XMAX + //#define ENDSTOPPULLUP_YMAX + //#define ENDSTOPPULLUP_ZMAX + //#define ENDSTOPPULLUP_XMIN + //#define ENDSTOPPULLUP_YMIN + //#define ENDSTOPPULLUP_ZMIN + //#define ENDSTOPPULLUP_ZMIN_PROBE +#endif + +// Enable pulldown for all endstops to prevent a floating state +//#define ENDSTOPPULLDOWNS +#if DISABLED(ENDSTOPPULLDOWNS) + // Disable ENDSTOPPULLDOWNS to set pulldowns individually + //#define ENDSTOPPULLDOWN_XMAX + //#define ENDSTOPPULLDOWN_YMAX + //#define ENDSTOPPULLDOWN_ZMAX + //#define ENDSTOPPULLDOWN_XMIN + //#define ENDSTOPPULLDOWN_YMIN + //#define ENDSTOPPULLDOWN_ZMIN + //#define ENDSTOPPULLDOWN_ZMIN_PROBE +#endif + +// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup). +#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop. +#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop. +#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop. +#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe. + +/** + * Stepper Drivers + * + * These settings allow Marlin to tune stepper driver timing and enable advanced options for + * stepper drivers that support them. You may also override timing options in Configuration_adv.h. + * + * A4988 is assumed for unspecified drivers. + * + * Options: A4988, A5984, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100, + * TMC2130, TMC2130_STANDALONE, TMC2160, TMC2160_STANDALONE, + * TMC2208, TMC2208_STANDALONE, TMC2209, TMC2209_STANDALONE, + * TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE, + * TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE + * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE'] + */ +#define X_DRIVER_TYPE A4988 +#define Y_DRIVER_TYPE A4988 +#define Z_DRIVER_TYPE A4988 +//#define X2_DRIVER_TYPE A4988 +//#define Y2_DRIVER_TYPE A4988 +//#define Z2_DRIVER_TYPE A4988 +//#define Z3_DRIVER_TYPE A4988 +#define E0_DRIVER_TYPE A4988 +//#define E1_DRIVER_TYPE A4988 +//#define E2_DRIVER_TYPE A4988 +//#define E3_DRIVER_TYPE A4988 +//#define E4_DRIVER_TYPE A4988 +//#define E5_DRIVER_TYPE A4988 + +// Enable this feature if all enabled endstop pins are interrupt-capable. +// This will remove the need to poll the interrupt pins, saving many CPU cycles. +//#define ENDSTOP_INTERRUPTS_FEATURE + +/** + * Endstop Noise Threshold + * + * Enable if your probe or endstops falsely trigger due to noise. + * + * - Higher values may affect repeatability or accuracy of some bed probes. + * - To fix noise install a 100nF ceramic capacitor inline with the switch. + * - This feature is not required for common micro-switches mounted on PCBs + * based on the Makerbot design, which already have the 100nF capacitor. + * + * :[2,3,4,5,6,7] + */ +//#define ENDSTOP_NOISE_THRESHOLD 2 + +//============================================================================= +//============================== Movement Settings ============================ +//============================================================================= +// @section motion + +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * With this option each E stepper can have its own factors for the + * following movement settings. If fewer factors are given than the + * total number of extruders, the last value applies to the rest. + */ +//#define DISTINCT_E_FACTORS + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] + */ +#define DEFAULT_AXIS_STEPS_PER_UNIT { 80.165, 80.165, 399.2901, 408 } + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] + */ +#define DEFAULT_MAX_FEEDRATE { 500, 500, 60, 55 } + +/** + * Default Max Acceleration (change/s) change = mm/s + * (Maximum start speed for accelerated moves) + * Override with M201 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] + */ +#define DEFAULT_MAX_ACCELERATION { 10000, 10000, 400, 10000 } + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 2000 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 10000 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 5000 // X, Y, Z acceleration for travel (non printing) moves + +/** + * Junction Deviation + * + * Use Junction Deviation instead of traditional Jerk Limiting + * + * See: + * https://reprap.org/forum/read.php?1,739819 + * http://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html + */ +//#define JUNCTION_DEVIATION +#if ENABLED(JUNCTION_DEVIATION) + #define JUNCTION_DEVIATION_MM 0.02 // (mm) Distance from real junction edge +#endif + +/** + * Default Jerk (mm/s) + * Override with M205 X Y Z E + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#if DISABLED(JUNCTION_DEVIATION) + #define DEFAULT_XJERK 10.0 + #define DEFAULT_YJERK 10.0 + #define DEFAULT_ZJERK 0.3 +#endif + +#define DEFAULT_EJERK 5.0 // May be used by Linear Advance + +/** + * S-Curve Acceleration + * + * This option eliminates vibration during printing by fitting a Bézier + * curve to move acceleration, producing much smoother direction changes. + * + * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained + */ +#define S_CURVE_ACCELERATION + +//=========================================================================== +//============================= Z Probe Options ============================= +//=========================================================================== +// @section probes + +// +// See http://marlinfw.org/docs/configuration/probes.html +// + +/** + * Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + * + * Enable this option for a probe connected to the Z Min endstop pin. + */ +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +/** + * Z_MIN_PROBE_PIN + * + * Define this pin if the probe is not connected to Z_MIN_PIN. + * If not defined the default pin for the selected MOTHERBOARD + * will be used. Most of the time the default is what you want. + * + * - The simplest option is to use a free endstop connector. + * - Use 5V for powered (usually inductive) sensors. + * + * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin: + * - For simple switches connect... + * - normally-closed switches to GND and D32. + * - normally-open switches to 5V and D32. + * + */ +//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default + +/** + * Probe Type + * + * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. + * Activate one of these to use Auto Bed Leveling below. + */ + +/** + * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe. + * Use G29 repeatedly, adjusting the Z height at each point with movement commands + * or (with LCD_BED_LEVELING) the LCD controller. + */ +//#define PROBE_MANUALLY +//#define MANUAL_PROBE_START_Z 0.2 + +/** + * A Fix-Mounted Probe either doesn't deploy or needs manual deployment. + * (e.g., an inductive probe or a nozzle-based probe-switch.) + */ +//#define FIX_MOUNTED_PROBE + +/** + * Z Servo Probe, such as an endstop switch on a rotating arm. + */ +//#define Z_PROBE_SERVO_NR 0 // Defaults to SERVO 0 connector. +//#define Z_SERVO_ANGLES { 70, 0 } // Z Servo Deploy and Stow angles + +/** + * The BLTouch probe uses a Hall effect sensor and emulates a servo. + */ +//#define BLTOUCH + +/** + * Touch-MI Probe by hotends.fr + * + * This probe is deployed and activated by moving the X-axis to a magnet at the edge of the bed. + * By default, the magnet is assumed to be on the left and activated by a home. If the magnet is + * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position. + * + * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING, + * and a minimum Z_HOMING_HEIGHT of 10. + */ +//#define TOUCH_MI_PROBE +#if ENABLED(TOUCH_MI_PROBE) + #define TOUCH_MI_RETRACT_Z 0.5 // Height at which the probe retracts + //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2) // For a magnet on the right side of the bed + //#define TOUCH_MI_MANUAL_DEPLOY // For manual deploy (LCD menu) +#endif + +// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) +//#define SOLENOID_PROBE + +// A sled-mounted probe like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +// A probe deployed by moving the x-axis, such as the Wilson II's rack-and-pinion probe designed by Marty Rice. +//#define RACK_AND_PINION_PROBE +#if ENABLED(RACK_AND_PINION_PROBE) + #define Z_PROBE_DEPLOY_X X_MIN_POS + #define Z_PROBE_RETRACT_X X_MAX_POS +#endif + +// +// For Z_PROBE_ALLEN_KEY see the Delta example configurations. +// + +/** + * Z Probe to nozzle (X,Y) offset, relative to (0, 0). + * X and Y offsets must be integers. + * + * In the following example the X and Y offsets are both positive: + * #define X_PROBE_OFFSET_FROM_EXTRUDER 10 + * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 + * + * +-- BACK ---+ + * | | + * L | (+) P | R <-- probe (20,20) + * E | | I + * F | (-) N (+) | G <-- nozzle (10,10) + * T | | H + * | (-) | T + * | | + * O-- FRONT --+ + * (0,0) + */ +#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle] + +// Certain types of probes need to stay away from edges +#define MIN_PROBE_EDGE 10 + +// X and Y axis travel speed (mm/m) between probes +#define XY_PROBE_SPEED 8000 + +// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2) +#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z + +// Feedrate (mm/m) for the "accurate" probe of each point +#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) + +/** + * Multiple Probing + * + * You may get improved results by probing 2 or more times. + * With EXTRA_PROBING the more atypical reading(s) will be disregarded. + * + * A total of 2 does fast/slow probes with a weighted average. + * A total of 3 or more adds more slow probes, taking the average. + */ +//#define MULTIPLE_PROBING 2 +//#define EXTRA_PROBING 1 + +/** + * Z probes require clearance when deploying, stowing, and moving between + * probe points to avoid hitting the bed and other hardware. + * Servo-mounted probes require extra space for the arm to rotate. + * Inductive probes need space to keep from triggering early. + * + * Use these settings to specify the distance (mm) to raise the probe (or + * lower the bed). The values set here apply over and above any (negative) + * probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD. + * Only integer values >= 1 are valid here. + * + * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle. + * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle. + */ +#define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow +#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points +#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes +//#define Z_AFTER_PROBING 5 // Z position after probing is done + +#define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping + +// For M851 give a range for adjusting the Z probe offset +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + +// Enable the M48 repeatability test to test probe accuracy +//#define Z_MIN_PROBE_REPEATABILITY_TEST + +// Before deploy/stow pause for user confirmation +//#define PAUSE_BEFORE_DEPLOY_STOW +#if ENABLED(PAUSE_BEFORE_DEPLOY_STOW) + //#define PAUSE_PROBE_DEPLOY_WHEN_TRIGGERED // For Manual Deploy Allenkey Probe +#endif + +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + +// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 +// :{ 0:'Low', 1:'High' } +#define X_ENABLE_ON 0 +#define Y_ENABLE_ON 0 +#define Z_ENABLE_ON 0 +#define E_ENABLE_ON 0 // For all extruders + +// Disables axis stepper immediately when it's not being used. +// WARNING: When motors turn off there is a chance of losing position accuracy! +#define DISABLE_X false +#define DISABLE_Y false +#define DISABLE_Z false + +// Warn on display about possibly reduced accuracy +//#define DISABLE_REDUCED_ACCURACY_WARNING + +// @section extruder + +#define DISABLE_E false // For all extruders +#define DISABLE_INACTIVE_EXTRUDER // Keep only the active extruder enabled + +// @section machine + +// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way. +#define INVERT_X_DIR false +#define INVERT_Y_DIR true +#define INVERT_Z_DIR true + +// @section extruder + +// For direct drive extruder v9 set to true, for geared extruder set to false. +#define INVERT_E0_DIR true +#define INVERT_E1_DIR false +#define INVERT_E2_DIR false +#define INVERT_E3_DIR false +#define INVERT_E4_DIR false +#define INVERT_E5_DIR false + +// @section homing + +//#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed + +//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off. + +//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ... + // Be sure you have this distance over your Z_MAX_POS in case. + +// Direction of endstops when homing; 1=MAX, -1=MIN +// :[-1,1] +#define X_HOME_DIR -1 +#define Y_HOME_DIR -1 +#define Z_HOME_DIR -1 + +// @section machine + +// The size of the print bed +#define X_BED_SIZE 150 +#define Y_BED_SIZE 150 + +// Travel limits (mm) after homing, corresponding to endstop positions. +#define X_MIN_POS -10 +#define Y_MIN_POS 0 +#define Z_MIN_POS 0 +#define X_MAX_POS X_BED_SIZE +#define Y_MAX_POS Y_BED_SIZE +#define Z_MAX_POS 160 + +/** + * Software Endstops + * + * - Prevent moves outside the set machine bounds. + * - Individual axes can be disabled, if desired. + * - X and Y only apply to Cartesian robots. + * - Use 'M211' to set software endstops on/off or report current state + */ + +// Min software endstops constrain movement within minimum coordinate bounds +#define MIN_SOFTWARE_ENDSTOPS +#if ENABLED(MIN_SOFTWARE_ENDSTOPS) + #define MIN_SOFTWARE_ENDSTOP_X + #define MIN_SOFTWARE_ENDSTOP_Y + #define MIN_SOFTWARE_ENDSTOP_Z +#endif + +// Max software endstops constrain movement within maximum coordinate bounds +#define MAX_SOFTWARE_ENDSTOPS +#if ENABLED(MAX_SOFTWARE_ENDSTOPS) + #define MAX_SOFTWARE_ENDSTOP_X + #define MAX_SOFTWARE_ENDSTOP_Y + #define MAX_SOFTWARE_ENDSTOP_Z +#endif + +#if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS) + //#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD +#endif + +/** + * Filament Runout Sensors + * Mechanical or opto endstops are used to check for the presence of filament. + * + * RAMPS-based boards use SERVO3_PIN for the first runout sensor. + * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc. + * By default the firmware assumes HIGH=FILAMENT PRESENT. + */ +//#define FILAMENT_RUNOUT_SENSOR +#if ENABLED(FILAMENT_RUNOUT_SENSOR) + #define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each. + #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor. + #define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins. + //#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins. + + // Set one or more commands to execute on filament runout. + // (After 'M412 H' Marlin will ask the host to handle the process.) + #define FILAMENT_RUNOUT_SCRIPT "M600" + + // After a runout is detected, continue printing this length of filament + // before executing the runout script. Useful for a sensor at the end of + // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead. + //#define FILAMENT_RUNOUT_DISTANCE_MM 25 + + #ifdef FILAMENT_RUNOUT_DISTANCE_MM + // Enable this option to use an encoder disc that toggles the runout pin + // as the filament moves. (Be sure to set FILAMENT_RUNOUT_DISTANCE_MM + // large enough to avoid false positives.) + //#define FILAMENT_MOTION_SENSOR + #endif +#endif + +//=========================================================================== +//=============================== Bed Leveling ============================== +//=========================================================================== +// @section calibrate + +/** + * Choose one of the options below to enable G29 Bed Leveling. The parameters + * and behavior of G29 will change depending on your selection. + * + * If using a Probe for Z Homing, enable Z_SAFE_HOMING also! + * + * - AUTO_BED_LEVELING_3POINT + * Probe 3 arbitrary points on the bed (that aren't collinear) + * You specify the XY coordinates of all 3 points. + * The result is a single tilted plane. Best for a flat bed. + * + * - AUTO_BED_LEVELING_LINEAR + * Probe several points in a grid. + * You specify the rectangle and the density of sample points. + * The result is a single tilted plane. Best for a flat bed. + * + * - AUTO_BED_LEVELING_BILINEAR + * Probe several points in a grid. + * You specify the rectangle and the density of sample points. + * The result is a mesh, best for large or uneven beds. + * + * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling) + * A comprehensive bed leveling system combining the features and benefits + * of other systems. UBL also includes integrated Mesh Generation, Mesh + * Validation and Mesh Editing systems. + * + * - MESH_BED_LEVELING + * Probe a grid manually + * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.) + * For machines without a probe, Mesh Bed Leveling provides a method to perform + * leveling in steps so you can manually adjust the Z height at each grid-point. + * With an LCD controller the process is guided step-by-step. + */ +//#define AUTO_BED_LEVELING_3POINT +//#define AUTO_BED_LEVELING_LINEAR +//#define AUTO_BED_LEVELING_BILINEAR +//#define AUTO_BED_LEVELING_UBL +#define MESH_BED_LEVELING + +/** + * Normally G28 leaves leveling disabled on completion. Enable + * this option to have G28 restore the prior leveling state. + */ +#define RESTORE_LEVELING_AFTER_G28 + +/** + * Enable detailed logging of G28, G29, M48, etc. + * Turn on with the command 'M111 S32'. + * NOTE: Requires a lot of PROGMEM! + */ +//#define DEBUG_LEVELING_FEATURE + +#if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_BILINEAR, AUTO_BED_LEVELING_UBL) + // Gradually reduce leveling correction until a set height is reached, + // at which point movement will be level to the machine's XY plane. + // The height can be set with M420 Z + #define ENABLE_LEVELING_FADE_HEIGHT + + // For Cartesian machines, instead of dividing moves on mesh boundaries, + // split up moves into short segments like a Delta. This follows the + // contours of the bed more closely than edge-to-edge straight moves. + #define SEGMENT_LEVELED_MOVES + #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one) + + /** + * Enable the G26 Mesh Validation Pattern tool. + */ + #define G26_MESH_VALIDATION + #if ENABLED(G26_MESH_VALIDATION) + #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle. + #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool. + #define MESH_TEST_HOTEND_TEMP 205 // (°C) Default nozzle temperature for the G26 Mesh Validation Tool. + #define MESH_TEST_BED_TEMP 60 // (°C) Default bed temperature for the G26 Mesh Validation Tool. + #define G26_XY_FEEDRATE 20 // (mm/s) Feedrate for XY Moves for the G26 Mesh Validation Tool. + #endif + +#endif + +#if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR) + + // Set the number of grid points per dimension. + #define GRID_MAX_POINTS_X 3 + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + // Set the boundaries for probing (where the probe can reach). + //#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE + //#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE)) + //#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE + //#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE)) + + // Probe along the Y axis, advancing X after each column + //#define PROBE_Y_FIRST + + #if ENABLED(AUTO_BED_LEVELING_BILINEAR) + + // Beyond the probed grid, continue the implied tilt? + // Default is to maintain the height of the nearest edge. + //#define EXTRAPOLATE_BEYOND_GRID + + // + // Experimental Subdivision of the grid by Catmull-Rom method. + // Synthesizes intermediate points to produce a more detailed mesh. + // + //#define ABL_BILINEAR_SUBDIVISION + #if ENABLED(ABL_BILINEAR_SUBDIVISION) + // Number of subdivisions between probe points + #define BILINEAR_SUBDIVISIONS 3 + #endif + + #endif + +#elif ENABLED(AUTO_BED_LEVELING_UBL) + + //=========================================================================== + //========================= Unified Bed Leveling ============================ + //=========================================================================== + + //#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh + + #define MESH_INSET 1 // Set Mesh bounds as an inset region of the bed + #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited. + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + #define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle + #define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500 + + //#define UBL_Z_RAISE_WHEN_OFF_MESH 2.5 // When the nozzle is off the mesh, this value is used + // as the Z-Height correction value. + +#elif ENABLED(MESH_BED_LEVELING) + + //=========================================================================== + //=================================== Mesh ================================== + //=========================================================================== + + #define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed + #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited. + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS + +#endif // BED_LEVELING + +/** + * Points to probe for all 3-point Leveling procedures. + * Override if the automatically selected points are inadequate. + */ +#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL) + //#define PROBE_PT_1_X 15 + //#define PROBE_PT_1_Y 180 + //#define PROBE_PT_2_X 15 + //#define PROBE_PT_2_Y 20 + //#define PROBE_PT_3_X 170 + //#define PROBE_PT_3_Y 20 +#endif + +/** + * Add a bed leveling sub-menu for ABL or MBL. + * Include a guided procedure if manual probing is enabled. + */ +#define LCD_BED_LEVELING + +#if ENABLED(LCD_BED_LEVELING) + #define MESH_EDIT_Z_STEP 0.025 // (mm) Step size while manually probing Z axis. + #define LCD_PROBE_Z_RANGE 4 // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment + //#define MESH_EDIT_MENU // Add a menu to edit mesh points +#endif + +// Add a menu item to move between bed corners for manual bed adjustment +#define LEVEL_BED_CORNERS + +#if ENABLED(LEVEL_BED_CORNERS) + #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner +#endif + +/** + * Commands to execute at the end of G29 probing. + * Useful to retract or move the Z probe out of the way. + */ +//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" + + +// @section homing + +// The center of the bed is at (X=0, Y=0) +//#define BED_CENTER_AT_0_0 + +// Manually set the home position. Leave these undefined for automatic settings. +// For DELTA this is the top-center of the Cartesian print volume. +//#define MANUAL_X_HOME_POS 0 +//#define MANUAL_Y_HOME_POS 0 +//#define MANUAL_Z_HOME_POS 0 + +// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area. +// +// With this feature enabled: +// +// - Allow Z homing only after X and Y homing AND stepper drivers still enabled. +// - If stepper drivers time out, it will need X and Y homing again before Z homing. +// - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28). +// - Prevent Z homing when the Z probe is outside bed area. +// +//#define Z_SAFE_HOMING + +#if ENABLED(Z_SAFE_HOMING) + #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing when homing all axes (G28). + #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2) // Y point for Z homing when homing all axes (G28). +#endif + +// Homing speeds (mm/m) +#define HOMING_FEEDRATE_XY (50*60) +#define HOMING_FEEDRATE_Z (4*60) + +// Validate that endstops are triggered on homing moves +#define VALIDATE_HOMING_ENDSTOPS + +// @section calibrate + +/** + * Bed Skew Compensation + * + * This feature corrects for misalignment in the XYZ axes. + * + * Take the following steps to get the bed skew in the XY plane: + * 1. Print a test square (e.g., https://www.thingiverse.com/thing:2563185) + * 2. For XY_DIAG_AC measure the diagonal A to C + * 3. For XY_DIAG_BD measure the diagonal B to D + * 4. For XY_SIDE_AD measure the edge A to D + * + * Marlin automatically computes skew factors from these measurements. + * Skew factors may also be computed and set manually: + * + * - Compute AB : SQRT(2*AC*AC+2*BD*BD-4*AD*AD)/2 + * - XY_SKEW_FACTOR : TAN(PI/2-ACOS((AC*AC-AB*AB-AD*AD)/(2*AB*AD))) + * + * If desired, follow the same procedure for XZ and YZ. + * Use these diagrams for reference: + * + * Y Z Z + * ^ B-------C ^ B-------C ^ B-------C + * | / / | / / | / / + * | / / | / / | / / + * | A-------D | A-------D | A-------D + * +-------------->X +-------------->X +-------------->Y + * XY_SKEW_FACTOR XZ_SKEW_FACTOR YZ_SKEW_FACTOR + */ +//#define SKEW_CORRECTION + +#if ENABLED(SKEW_CORRECTION) + // Input all length measurements here: + #define XY_DIAG_AC 282.8427124746 + #define XY_DIAG_BD 282.8427124746 + #define XY_SIDE_AD 200 + + // Or, set the default skew factors directly here + // to override the above measurements: + #define XY_SKEW_FACTOR 0.0 + + //#define SKEW_CORRECTION_FOR_Z + #if ENABLED(SKEW_CORRECTION_FOR_Z) + #define XZ_DIAG_AC 282.8427124746 + #define XZ_DIAG_BD 282.8427124746 + #define YZ_DIAG_AC 282.8427124746 + #define YZ_DIAG_BD 282.8427124746 + #define YZ_SIDE_AD 200 + #define XZ_SKEW_FACTOR 0.0 + #define YZ_SKEW_FACTOR 0.0 + #endif + + // Enable this option for M852 to set skew at runtime + //#define SKEW_CORRECTION_GCODE +#endif + +//============================================================================= +//============================= Additional Features =========================== +//============================================================================= + +// @section extras + +/** + * EEPROM + * + * Persistent storage to preserve configurable settings across reboots. + * + * M500 - Store settings to EEPROM. + * M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes) + * M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.) + */ +#define EEPROM_SETTINGS // Persistent storage with M500 and M501 +//#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release! +#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM. +#if ENABLED(EEPROM_SETTINGS) + #define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors. +#endif + +// +// Host Keepalive +// +// When enabled Marlin will send a busy status message to the host +// every couple of seconds when it can't accept commands. +// +#define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages +#define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113. +#define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating + +// +// M100 Free Memory Watcher +// +//#define M100_FREE_MEMORY_WATCHER // Add M100 (Free Memory Watcher) to debug memory usage + +// +// G20/G21 Inch mode support +// +//#define INCH_MODE_SUPPORT + +// +// M149 Set temperature units support +// +//#define TEMPERATURE_UNITS_SUPPORT + +// @section temperature + +// Preheat Constants +#define PREHEAT_1_LABEL "PLA" +#define PREHEAT_1_TEMP_HOTEND 200 +#define PREHEAT_1_TEMP_BED 70 +#define PREHEAT_1_FAN_SPEED 255 // Value from 0 to 255 + +#define PREHEAT_2_LABEL "PETG" +#define PREHEAT_2_TEMP_HOTEND 240 +#define PREHEAT_2_TEMP_BED 110 +#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255 + +/** + * Nozzle Park + * + * Park the nozzle at the given XYZ position on idle or G27. + * + * The "P" parameter controls the action applied to the Z axis: + * + * P0 (Default) If Z is below park Z raise the nozzle. + * P1 Raise the nozzle always to Z-park height. + * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS. + */ +#define NOZZLE_PARK_FEATURE + +#if ENABLED(NOZZLE_PARK_FEATURE) + // Specify a park position as { X, Y, Z_raise } + #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 } + #define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis) + #define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers) +#endif + +/** + * Clean Nozzle Feature -- EXPERIMENTAL + * + * Adds the G12 command to perform a nozzle cleaning process. + * + * Parameters: + * P Pattern + * S Strokes / Repetitions + * T Triangles (P1 only) + * + * Patterns: + * P0 Straight line (default). This process requires a sponge type material + * at a fixed bed location. "S" specifies strokes (i.e. back-forth motions) + * between the start / end points. + * + * P1 Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the + * number of zig-zag triangles to do. "S" defines the number of strokes. + * Zig-zags are done in whichever is the narrower dimension. + * For example, "G12 P1 S1 T3" will execute: + * + * -- + * | (X0, Y1) | /\ /\ /\ | (X1, Y1) + * | | / \ / \ / \ | + * A | | / \ / \ / \ | + * | | / \ / \ / \ | + * | (X0, Y0) | / \/ \/ \ | (X1, Y0) + * -- +--------------------------------+ + * |________|_________|_________| + * T1 T2 T3 + * + * P2 Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE. + * "R" specifies the radius. "S" specifies the stroke count. + * Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT. + * + * Caveats: The ending Z should be the same as starting Z. + * Attention: EXPERIMENTAL. G-code arguments may change. + * + */ +#define NOZZLE_CLEAN_FEATURE + +#if ENABLED(NOZZLE_CLEAN_FEATURE) + // Default number of pattern repetitions + #define NOZZLE_CLEAN_STROKES 12 + + // Default number of triangles + #define NOZZLE_CLEAN_TRIANGLES 3 + + // Specify positions as { X, Y, Z } + #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)} + #define NOZZLE_CLEAN_END_POINT { 100, 60, (Z_MIN_POS + 1) } + + // Circular pattern radius + #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5 + // Circular pattern circle fragments number + #define NOZZLE_CLEAN_CIRCLE_FN 10 + // Middle point of circle + #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT + + // Move the nozzle to the initial position after cleaning + #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z +#endif + +/** + * Print Job Timer + * + * Automatically start and stop the print job timer on M104/M109/M190. + * + * M104 (hotend, no wait) - high temp = none, low temp = stop timer + * M109 (hotend, wait) - high temp = start timer, low temp = stop timer + * M190 (bed, wait) - high temp = start timer, low temp = none + * + * The timer can also be controlled with the following commands: + * + * M75 - Start the print job timer + * M76 - Pause the print job timer + * M77 - Stop the print job timer + */ +#define PRINTJOB_TIMER_AUTOSTART + +/** + * Print Counter + * + * Track statistical data such as: + * + * - Total print jobs + * - Total successful print jobs + * - Total failed print jobs + * - Total time printing + * + * View the current statistics with M78. + */ +#define PRINTCOUNTER + +//============================================================================= +//============================= LCD and SD support ============================ +//============================================================================= + +// @section lcd + +/** + * LCD LANGUAGE + * + * Select the language to display on the LCD. These languages are available: + * + * en, an, bg, ca, cz, da, de, el, el-gr, es, eu, fi, fr, gl, hr, it, + * jp-kana, ko_KR, nl, pl, pt, pt-br, ru, sk, tr, uk, zh_CN, zh_TW, test + * + * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cz':'Czech', 'da':'Danish', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'jp-kana':'Japanese', 'ko_KR':'Korean (South Korea)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'ru':'Russian', 'sk':'Slovak', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Traditional)', 'test':'TEST' } + */ +#define LCD_LANGUAGE en + +/** + * LCD Character Set + * + * Note: This option is NOT applicable to Graphical Displays. + * + * All character-based LCDs provide ASCII plus one of these + * language extensions: + * + * - JAPANESE ... the most common + * - WESTERN ... with more accented characters + * - CYRILLIC ... for the Russian language + * + * To determine the language extension installed on your controller: + * + * - Compile and upload with LCD_LANGUAGE set to 'test' + * - Click the controller to view the LCD menu + * - The LCD will display Japanese, Western, or Cyrillic text + * + * See http://marlinfw.org/docs/development/lcd_language.html + * + * :['JAPANESE', 'WESTERN', 'CYRILLIC'] + */ +#define DISPLAY_CHARSET_HD44780 WESTERN + +/** + * Info Screen Style (0:Classic, 1:Prusa) + * + * :[0:'Classic', 1:'Prusa'] + */ +#define LCD_INFO_SCREEN_STYLE 0 + +/** + * SD CARD + * + * SD Card support is disabled by default. If your controller has an SD slot, + * you must uncomment the following option or it won't work. + * + */ +#define SDSUPPORT + +/** + * SD CARD: SPI SPEED + * + * Enable one of the following items for a slower SPI transfer speed. + * This may be required to resolve "volume init" errors. + */ +//#define SPI_SPEED SPI_HALF_SPEED +//#define SPI_SPEED SPI_QUARTER_SPEED +//#define SPI_SPEED SPI_EIGHTH_SPEED + +/** + * SD CARD: ENABLE CRC + * + * Use CRC checks and retries on the SD communication. + */ +//#define SD_CHECK_AND_RETRY + +/** + * LCD Menu Items + * + * Disable all menus and only display the Status Screen, or + * just remove some extraneous menu items to recover space. + */ +//#define NO_LCD_MENUS +//#define SLIM_LCD_MENUS + +// +// ENCODER SETTINGS +// +// This option overrides the default number of encoder pulses needed to +// produce one step. Should be increased for high-resolution encoders. +// +#define ENCODER_PULSES_PER_STEP 4 + +// +// Use this option to override the number of step signals required to +// move between next/prev menu items. +// +#define ENCODER_STEPS_PER_MENU_ITEM 1 + +/** + * Encoder Direction Options + * + * Test your encoder's behavior first with both options disabled. + * + * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION. + * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION. + * Reversed Value Editing only? Enable BOTH options. + */ + +// +// This option reverses the encoder direction everywhere. +// +// Set this option if CLOCKWISE causes values to DECREASE +// +#define REVERSE_ENCODER_DIRECTION + +// +// This option reverses the encoder direction for navigating LCD menus. +// +// If CLOCKWISE normally moves DOWN this makes it go UP. +// If CLOCKWISE normally moves UP this makes it go DOWN. +// +//#define REVERSE_MENU_DIRECTION + +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + +// +// Individual Axis Homing +// +// Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu. +// +#define INDIVIDUAL_AXIS_HOMING_MENU + +// +// SPEAKER/BUZZER +// +// If you have a speaker that can produce tones, enable it here. +// By default Marlin assumes you have a buzzer with a fixed frequency. +// +#define SPEAKER + +// +// The duration and frequency for the UI feedback sound. +// Set these to 0 to disable audio feedback in the LCD menus. +// +// Note: Test audio output with the G-Code: +// M300 S P +// +#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 2 +#define LCD_FEEDBACK_FREQUENCY_HZ 5000 + +//============================================================================= +//======================== LCD / Controller Selection ========================= +//======================== (Character-based LCDs) ========================= +//============================================================================= + +// +// RepRapDiscount Smart Controller. +// http://reprap.org/wiki/RepRapDiscount_Smart_Controller +// +// Note: Usually sold with a white PCB. +// +//#define REPRAP_DISCOUNT_SMART_CONTROLLER + +// +// Original RADDS LCD Display+Encoder+SDCardReader +// http://doku.radds.org/dokumentation/lcd-display/ +// +//#define RADDS_DISPLAY + +// +// ULTIMAKER Controller. +// +//#define ULTIMAKERCONTROLLER + +// +// ULTIPANEL as seen on Thingiverse. +// +//#define ULTIPANEL + +// +// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3) +// http://reprap.org/wiki/PanelOne +// +//#define PANEL_ONE + +// +// GADGETS3D G3D LCD/SD Controller +// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel +// +// Note: Usually sold with a blue PCB. +// +//#define G3D_PANEL + +// +// RigidBot Panel V1.0 +// http://www.inventapart.com/ +// +//#define RIGIDBOT_PANEL + +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// ANET and Tronxy 20x4 Controller +// +//#define ZONESTAR_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin. + // This LCD is known to be susceptible to electrical interference + // which scrambles the display. Pressing any button clears it up. + // This is a LCD2004 display with 5 analog buttons. + +// +// Generic 16x2, 16x4, 20x2, or 20x4 character-based LCD. +// +//#define ULTRA_LCD + +//============================================================================= +//======================== LCD / Controller Selection ========================= +//===================== (I2C and Shift-Register LCDs) ===================== +//============================================================================= + +// +// CONTROLLER TYPE: I2C +// +// Note: These controllers require the installation of Arduino's LiquidCrystal_I2C +// library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C +// + +// +// Elefu RA Board Control Panel +// http://www.elefu.com/index.php?route=product/product&product_id=53 +// +//#define RA_CONTROL_PANEL + +// +// Sainsmart (YwRobot) LCD Displays +// +// These require F.Malpartida's LiquidCrystal_I2C library +// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home +// +//#define LCD_SAINSMART_I2C_1602 +//#define LCD_SAINSMART_I2C_2004 + +// +// Generic LCM1602 LCD adapter +// +//#define LCM1602 + +// +// PANELOLU2 LCD with status LEDs, +// separate encoder and click inputs. +// +// Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later. +// For more info: https://github.com/lincomatic/LiquidTWI2 +// +// Note: The PANELOLU2 encoder click input can either be directly connected to +// a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1). +// +//#define LCD_I2C_PANELOLU2 + +// +// Panucatt VIKI LCD with status LEDs, +// integrated click & L/R/U/D buttons, separate encoder inputs. +// +//#define LCD_I2C_VIKI + +// +// CONTROLLER TYPE: Shift register panels +// + +// +// 2-wire Non-latching LCD SR from https://goo.gl/aJJ4sH +// LCD configuration: http://reprap.org/wiki/SAV_3D_LCD +// +//#define SAV_3DLCD + +// +// 3-wire SR LCD with strobe using 74HC4094 +// https://github.com/mikeshub/SailfishLCD +// Uses the code directly from Sailfish +// +//#define FF_INTERFACEBOARD + +//============================================================================= +//======================= LCD / Controller Selection ======================= +//========================= (Graphical LCDs) ======================== +//============================================================================= + +// +// CONTROLLER TYPE: Graphical 128x64 (DOGM) +// +// IMPORTANT: The U8glib library is required for Graphical Display! +// https://github.com/olikraus/U8glib_Arduino +// + +// +// RepRapDiscount FULL GRAPHIC Smart Controller +// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller +// +//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER + +// +// ReprapWorld Graphical LCD +// https://reprapworld.com/?products_details&products_id/1218 +// +//#define REPRAPWORLD_GRAPHICAL_LCD + +// +// Activate one of these if you have a Panucatt Devices +// Viki 2.0 or mini Viki with Graphic LCD +// http://panucatt.com +// +//#define VIKI2 +//#define miniVIKI + +// +// MakerLab Mini Panel with graphic +// controller and SD support - http://reprap.org/wiki/Mini_panel +// +//#define MINIPANEL + +// +// MaKr3d Makr-Panel with graphic controller and SD support. +// http://reprap.org/wiki/MaKr3d_MaKrPanel +// +//#define MAKRPANEL + +// +// Adafruit ST7565 Full Graphic Controller. +// https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/ +// +//#define ELB_FULL_GRAPHIC_CONTROLLER + +// +// BQ LCD Smart Controller shipped by +// default with the BQ Hephestos 2 and Witbox 2. +// +//#define BQ_LCD_SMART_CONTROLLER + +// +// Cartesio UI +// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// +//#define CARTESIO_UI + +// +// LCD for Melzi Card with Graphical LCD +// +//#define LCD_FOR_MELZI + +// +// Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder +// https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) +// +//#define ULTI_CONTROLLER + +// +// MKS MINI12864 with graphic controller and SD support +// https://reprap.org/wiki/MKS_MINI_12864 +// +#define MKS_MINI_12864 + +// +// FYSETC variant of the MINI12864 graphic controller with SD support +// https://wiki.fysetc.com/Mini12864_Panel/ +// +//#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default +//#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) +//#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// ANET and Tronxy Graphical Controller +// +// Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6 +// A clone of the RepRapDiscount full graphics display but with +// different pins/wiring (see pins_ANET_10.h). +// +//#define ANET_FULL_GRAPHICS_LCD + +// +// AZSMZ 12864 LCD with SD +// https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html +// +//#define AZSMZ_12864 + +// +// Silvergate GLCD controller +// http://github.com/android444/Silvergate +// +//#define SILVER_GATE_GLCD_CONTROLLER + +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + +//============================================================================= +//========================== Extensible UI Displays =========================== +//============================================================================= + +// +// DGUS Touch Display with DWIN OS +// +//#define DGUS_LCD + +// +// Touch-screen LCD for Malyan M200 printers +// +//#define MALYAN_LCD + +// +// Third-party or vendor-customized controller interfaces. +// Sources should be installed in 'src/lcd/extensible_ui'. +// +//#define EXTENSIBLE_UI + +//============================================================================= +//=============================== Graphical TFTs ============================== +//============================================================================= + +// +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) +// +//#define FSMC_GRAPHICAL_TFT + +//============================================================================= +//============================ Other Controllers ============================ +//============================================================================= + +// +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 +// +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif + +// +// RepRapWorld REPRAPWORLD_KEYPAD v1.1 +// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626 +// +// REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key +// is pressed, a value of 10.0 means 10mm per click. +// +//#define REPRAPWORLD_KEYPAD +//#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 + +//============================================================================= +//=============================== Extra Features ============================== +//============================================================================= + +// @section extras + +// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino +//#define FAST_PWM_FAN + +// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency +// which is not as annoying as with the hardware PWM. On the other hand, if this frequency +// is too low, you should also increment SOFT_PWM_SCALE. +//#define FAN_SOFT_PWM + +// Incrementing this by 1 will double the software PWM frequency, +// affecting heaters, and the fan if FAN_SOFT_PWM is enabled. +// However, control resolution will be halved for each increment; +// at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] +#define SOFT_PWM_SCALE 0 + +// If SOFT_PWM_SCALE is set to a value higher than 0, dithering can +// be used to mitigate the associated resolution loss. If enabled, +// some of the PWM cycles are stretched so on average the desired +// duty cycle is attained. +//#define SOFT_PWM_DITHER + +// Temperature status LEDs that display the hotend and bed temperature. +// If all hotends, bed temperature, and target temperature are under 54C +// then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis) +//#define TEMP_STAT_LEDS + +// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure +//#define SF_ARC_FIX + +// Support for the BariCUDA Paste Extruder +//#define BARICUDA + +// Support for BlinkM/CyzRgb +//#define BLINKM + +// Support for PCA9632 PWM LED driver +//#define PCA9632 + +// Support for PCA9533 PWM LED driver +// https://github.com/mikeshub/SailfishRGB_LED +//#define PCA9533 + +/** + * RGB LED / LED Strip Control + * + * Enable support for an RGB LED connected to 5V digital pins, or + * an RGB Strip connected to MOSFETs controlled by digital pins. + * + * Adds the M150 command to set the LED (or LED strip) color. + * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of + * luminance values can be set from 0 to 255. + * For Neopixel LED an overall brightness parameter is also available. + * + * *** CAUTION *** + * LED Strips require a MOSFET Chip between PWM lines and LEDs, + * as the Arduino cannot handle the current the LEDs will require. + * Failure to follow this precaution can destroy your Arduino! + * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * more current than the Arduino 5V linear regulator can produce. + * *** CAUTION *** + * + * LED Type. Enable only one of the following two options. + * + */ +//#define RGB_LED +//#define RGBW_LED + +#if EITHER(RGB_LED, RGBW_LED) + //#define RGB_LED_R_PIN 34 + //#define RGB_LED_G_PIN 43 + //#define RGB_LED_B_PIN 35 + //#define RGB_LED_W_PIN -1 +#endif + +// Support for Adafruit Neopixel LED driver +//#define NEOPIXEL_LED +#if ENABLED(NEOPIXEL_LED) + #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. + #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) + //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup + + // Use a single Neopixel LED for static (background) lighting + //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use + //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W +#endif + +/** + * Printer Event LEDs + * + * During printing, the LEDs will reflect the printer status: + * + * - Gradually change from blue to violet as the heated bed gets to target temp + * - Gradually change from violet to red as the hotend gets to temperature + * - Change to white to illuminate work surface + * - Change to green once print has finished + * - Turn off after the print has finished and the user has pushed a button + */ +#if ANY(BLINKM, RGB_LED, RGBW_LED, PCA9632, PCA9533, NEOPIXEL_LED) + #define PRINTER_EVENT_LEDS +#endif + +/** + * R/C SERVO support + * Sponsored by TrinityLabs, Reworked by codexmas + */ + +/** + * Number of servos + * + * For some servo-related options NUM_SERVOS will be set automatically. + * Set this manually if there are extra servos needing manual control. + * Leave undefined or set to 0 to entirely disable the servo subsystem. + */ +//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command + +// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. +// 300ms is a good value but you can try less delay. +// If the servo can't reach the requested position, increase it. +#define SERVO_DELAY { 300 } + +// Only power servos during movement, otherwise leave off to prevent jitter +//#define DEACTIVATE_SERVOS_AFTER_MOVE + +// Allow servo angle to be edited and saved to EEPROM +//#define EDITABLE_SERVO_ANGLES diff --git a/config/examples/Tevo/Michelangelo/Configuration_adv.h b/config/examples/Tevo/Michelangelo/Configuration_adv.h new file mode 100644 index 0000000000..5fa2557db4 --- /dev/null +++ b/config/examples/Tevo/Michelangelo/Configuration_adv.h @@ -0,0 +1,2561 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Configuration_adv.h + * + * Advanced settings. + * Only change these if you know exactly what you're doing. + * Some of these settings can damage your printer if improperly set! + * + * Basic settings can be found in Configuration.h + * + */ +#define CONFIGURATION_ADV_H_VERSION 020000 + +// @section temperature + +//=========================================================================== +//=============================Thermal Settings ============================ +//=========================================================================== + +// +// Custom Thermistor 1000 parameters +// +#if TEMP_SENSOR_0 == 1000 + #define HOTEND0_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND0_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND0_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_1 == 1000 + #define HOTEND1_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND1_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND1_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_2 == 1000 + #define HOTEND2_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND2_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND2_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_3 == 1000 + #define HOTEND3_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND3_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND3_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_4 == 1000 + #define HOTEND4_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND4_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND4_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_5 == 1000 + #define HOTEND5_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND5_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND5_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_BED == 1000 + #define BED_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define BED_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define BED_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_CHAMBER == 1000 + #define CHAMBER_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define CHAMBER_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define CHAMBER_BETA 3950 // Beta value +#endif + +// +// Hephestos 2 24V heated bed upgrade kit. +// https://store.bq.com/en/heated-bed-kit-hephestos2 +// +//#define HEPHESTOS2_HEATED_BED_KIT +#if ENABLED(HEPHESTOS2_HEATED_BED_KIT) + #undef TEMP_SENSOR_BED + #define TEMP_SENSOR_BED 70 + #define HEATER_BED_INVERTING true +#endif + +/** + * Heated Chamber settings + */ +#if TEMP_SENSOR_CHAMBER + #define CHAMBER_MINTEMP 5 + #define CHAMBER_MAXTEMP 60 + #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target + //#define CHAMBER_LIMIT_SWITCHING + //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin + //#define HEATER_CHAMBER_INVERTING false +#endif + +#if DISABLED(PIDTEMPBED) + #define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control + #if ENABLED(BED_LIMIT_SWITCHING) + #define BED_HYSTERESIS 2 // Only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS + #endif +#endif + +/** + * Thermal Protection provides additional protection to your printer from damage + * and fire. Marlin always includes safe min and max temperature ranges which + * protect against a broken or disconnected thermistor wire. + * + * The issue: If a thermistor falls out, it will report the much lower + * temperature of the air in the room, and the the firmware will keep + * the heater on. + * + * The solution: Once the temperature reaches the target, start observing. + * If the temperature stays too far below the target (hysteresis) for too + * long (period), the firmware will halt the machine as a safety precaution. + * + * If you get false positives for "Thermal Runaway", increase + * THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD + */ +#if ENABLED(THERMAL_PROTECTION_HOTENDS) + #define THERMAL_PROTECTION_PERIOD 40 // Seconds + #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius + + //#define ADAPTIVE_FAN_SLOWING // Slow part cooling fan if temperature drops + #if BOTH(ADAPTIVE_FAN_SLOWING, PIDTEMP) + //#define NO_FAN_SLOWING_IN_PID_TUNING // Don't slow fan speed during M303 + #endif + + /** + * Whenever an M104, M109, or M303 increases the target temperature, the + * firmware will wait for the WATCH_TEMP_PERIOD to expire. If the temperature + * hasn't increased by WATCH_TEMP_INCREASE degrees, the machine is halted and + * requires a hard reset. This test restarts with any M104/M109/M303, but only + * if the current temperature is far enough below the target for a reliable + * test. + * + * If you get false positives for "Heating failed", increase WATCH_TEMP_PERIOD + * and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set + * below 2. + */ + #define WATCH_TEMP_PERIOD 20 // Seconds + #define WATCH_TEMP_INCREASE 2 // Degrees Celsius +#endif + +/** + * Thermal Protection parameters for the bed are just as above for hotends. + */ +#if ENABLED(THERMAL_PROTECTION_BED) + #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds + #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius + + /** + * As described above, except for the bed (M140/M190/M303). + */ + #define WATCH_BED_TEMP_PERIOD 60 // Seconds + #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius +#endif + +/** + * Thermal Protection parameters for the heated chamber. + */ +#if ENABLED(THERMAL_PROTECTION_CHAMBER) + #define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds + #define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius + + /** + * Heated chamber watch settings (M141/M191). + */ + #define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds + #define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius +#endif + +#if ENABLED(PIDTEMP) + // Add an experimental additional term to the heater power, proportional to the extrusion speed. + // A well-chosen Kc value should add just enough power to melt the increased material volume. + //#define PID_EXTRUSION_SCALING + #if ENABLED(PID_EXTRUSION_SCALING) + #define DEFAULT_Kc (100) //heating power=Kc*(e_speed) + #define LPQ_MAX_LEN 50 + #endif +#endif + +/** + * Automatic Temperature: + * The hotend target temperature is calculated by all the buffered lines of gcode. + * The maximum buffered steps/sec of the extruder motor is called "se". + * Start autotemp mode with M109 S B F + * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by + * mintemp and maxtemp. Turn this off by executing M109 without F* + * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp. + * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode + */ +#define AUTOTEMP +#if ENABLED(AUTOTEMP) + #define AUTOTEMP_OLDWEIGHT 0.98 +#endif + +// Show extra position information in M114 +//#define M114_DETAIL + +// Show Temperature ADC value +// Enable for M105 to include ADC values read from temperature sensors. +//#define SHOW_TEMP_ADC_VALUES + +/** + * High Temperature Thermistor Support + * + * Thermistors able to support high temperature tend to have a hard time getting + * good readings at room and lower temperatures. This means HEATER_X_RAW_LO_TEMP + * will probably be caught when the heating element first turns on during the + * preheating process, which will trigger a min_temp_error as a safety measure + * and force stop everything. + * To circumvent this limitation, we allow for a preheat time (during which, + * min_temp_error won't be triggered) and add a min_temp buffer to handle + * aberrant readings. + * + * If you want to enable this feature for your hotend thermistor(s) + * uncomment and set values > 0 in the constants below + */ + +// The number of consecutive low temperature errors that can occur +// before a min_temp_error is triggered. (Shouldn't be more than 10.) +//#define MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED 0 + +// The number of milliseconds a hotend will preheat before starting to check +// the temperature. This value should NOT be set to the time it takes the +// hot end to reach the target temperature, but the time it takes to reach +// the minimum temperature your thermistor can read. The lower the better/safer. +// This shouldn't need to be more than 30 seconds (30000) +//#define MILLISECONDS_PREHEAT_TIME 0 + +// @section extruder + +// Extruder runout prevention. +// If the machine is idle and the temperature over MINTEMP +// then extrude some filament every couple of SECONDS. +//#define EXTRUDER_RUNOUT_PREVENT +#if ENABLED(EXTRUDER_RUNOUT_PREVENT) + #define EXTRUDER_RUNOUT_MINTEMP 190 + #define EXTRUDER_RUNOUT_SECONDS 30 + #define EXTRUDER_RUNOUT_SPEED 1500 // (mm/m) + #define EXTRUDER_RUNOUT_EXTRUDE 5 // (mm) +#endif + +// @section temperature + +// Calibration for AD595 / AD8495 sensor to adjust temperature measurements. +// The final temperature is calculated as (measuredTemp * GAIN) + OFFSET. +#define TEMP_SENSOR_AD595_OFFSET 0.0 +#define TEMP_SENSOR_AD595_GAIN 1.0 +#define TEMP_SENSOR_AD8495_OFFSET 0.0 +#define TEMP_SENSOR_AD8495_GAIN 1.0 + +/** + * Controller Fan + * To cool down the stepper drivers and MOSFETs. + * + * The fan will turn on automatically whenever any stepper is enabled + * and turn off after a set period after all steppers are turned off. + */ +//#define USE_CONTROLLER_FAN +#if ENABLED(USE_CONTROLLER_FAN) + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled + #define CONTROLLERFAN_SPEED 255 // 255 == full speed +#endif + +// When first starting the main fan, run it at full speed for the +// given number of milliseconds. This gets the fan spinning reliably +// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) +#define FAN_KICKSTART_TIME 100 + +/** + * PWM Fan Scaling + * + * Define the min/max speeds for PWM fans (as set with M106). + * + * With these options the M106 0-255 value range is scaled to a subset + * to ensure that the fan has enough power to spin, or to run lower + * current fans with higher current. (e.g., 5V/12V fans with 12V/24V) + * Value 0 always turns off the fan. + * + * Define one or both of these to override the default 0-255 range. + */ +//#define FAN_MIN_PWM 50 +//#define FAN_MAX_PWM 128 + +/** + * FAST PWM FAN Settings + * + * Use to change the FAST FAN PWM frequency (if enabled in Configuration.h) + * Combinations of PWM Modes, prescale values and TOP resolutions are used internally to produce a + * frequency as close as possible to the desired frequency. + * + * FAST_PWM_FAN_FREQUENCY [undefined by default] + * Set this to your desired frequency. + * If left undefined this defaults to F = F_CPU/(2*255*1) + * ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers + * These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required + * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior. + * + * USE_OCR2A_AS_TOP [undefined by default] + * Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2: + * 16MHz MCUs: [62.5KHz, 31.4KHz (default), 7.8KHz, 3.92KHz, 1.95KHz, 977Hz, 488Hz, 244Hz, 60Hz, 122Hz, 30Hz] + * 20MHz MCUs: [78.1KHz, 39.2KHz (default), 9.77KHz, 4.9KHz, 2.44KHz, 1.22KHz, 610Hz, 305Hz, 153Hz, 76Hz, 38Hz] + * A greater range can be achieved by enabling USE_OCR2A_AS_TOP. But note that this option blocks the use of + * PWM on pin OC2A. Only use this option if you don't need PWM on 0C2A. (Check your schematic.) + * USE_OCR2A_AS_TOP sacrifices duty cycle control resolution to achieve this broader range of frequencies. + */ +#if ENABLED(FAST_PWM_FAN) + //#define FAST_PWM_FAN_FREQUENCY 31400 + //#define USE_OCR2A_AS_TOP +#endif + +// @section extruder + +/** + * Extruder cooling fans + * + * Extruder auto fans automatically turn on when their extruders' + * temperatures go above EXTRUDER_AUTO_FAN_TEMPERATURE. + * + * Your board's pins file specifies the recommended pins. Override those here + * or set to -1 to disable completely. + * + * Multiple extruders can be assigned to the same pin in which case + * the fan will turn on when any selected extruder is above the threshold. + */ +#define E0_AUTO_FAN_PIN 7 +#define E1_AUTO_FAN_PIN -1 +#define E2_AUTO_FAN_PIN -1 +#define E3_AUTO_FAN_PIN -1 +#define E4_AUTO_FAN_PIN -1 +#define E5_AUTO_FAN_PIN -1 +#define CHAMBER_AUTO_FAN_PIN -1 + +#define EXTRUDER_AUTO_FAN_TEMPERATURE 50 +#define EXTRUDER_AUTO_FAN_SPEED 255 // 255 == full speed +#define CHAMBER_AUTO_FAN_TEMPERATURE 30 +#define CHAMBER_AUTO_FAN_SPEED 255 + +/** + * Part-Cooling Fan Multiplexer + * + * This feature allows you to digitally multiplex the fan output. + * The multiplexer is automatically switched at tool-change. + * Set FANMUX[012]_PINs below for up to 2, 4, or 8 multiplexed fans. + */ +#define FANMUX0_PIN -1 +#define FANMUX1_PIN -1 +#define FANMUX2_PIN -1 + +/** + * M355 Case Light on-off / brightness + */ +//#define CASE_LIGHT_ENABLE +#if ENABLED(CASE_LIGHT_ENABLE) + //#define CASE_LIGHT_PIN 4 // Override the default pin if needed + #define INVERT_CASE_LIGHT false // Set true if Case Light is ON when pin is LOW + #define CASE_LIGHT_DEFAULT_ON true // Set default power-up state on + #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105 // Set default power-up brightness (0-255, requires PWM pin) + //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu + //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. + //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) + #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } + #endif +#endif + +// @section homing + +// If you want endstops to stay on (by default) even when not homing +// enable this option. Override at any time with M120, M121. +//#define ENDSTOPS_ALWAYS_ON_DEFAULT + +// @section extras + +//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats. + +// Employ an external closed loop controller. Override pins here if needed. +//#define EXTERNAL_CLOSED_LOOP_CONTROLLER +#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER) + //#define CLOSED_LOOP_ENABLE_PIN -1 + //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1 +#endif + +/** + * Dual Steppers / Dual Endstops + * + * This section will allow you to use extra E drivers to drive a second motor for X, Y, or Z axes. + * + * For example, set X_DUAL_STEPPER_DRIVERS setting to use a second motor. If the motors need to + * spin in opposite directions set INVERT_X2_VS_X_DIR. If the second motor needs its own endstop + * set X_DUAL_ENDSTOPS. This can adjust for "racking." Use X2_USE_ENDSTOP to set the endstop plug + * that should be used for the second endstop. Extra endstops will appear in the output of 'M119'. + * + * Use X_DUAL_ENDSTOP_ADJUSTMENT to adjust for mechanical imperfection. After homing both motors + * this offset is applied to the X2 motor. To find the offset home the X axis, and measure the error + * in X2. Dual endstop offsets can be set at runtime with 'M666 X Y Z'. + */ + +//#define X_DUAL_STEPPER_DRIVERS +#if ENABLED(X_DUAL_STEPPER_DRIVERS) + #define INVERT_X2_VS_X_DIR true // Set 'true' if X motors should rotate in opposite directions + //#define X_DUAL_ENDSTOPS + #if ENABLED(X_DUAL_ENDSTOPS) + #define X2_USE_ENDSTOP _XMAX_ + #define X_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Y_DUAL_STEPPER_DRIVERS +#if ENABLED(Y_DUAL_STEPPER_DRIVERS) + #define INVERT_Y2_VS_Y_DIR true // Set 'true' if Y motors should rotate in opposite directions + //#define Y_DUAL_ENDSTOPS + #if ENABLED(Y_DUAL_ENDSTOPS) + #define Y2_USE_ENDSTOP _YMAX_ + #define Y_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Z_DUAL_STEPPER_DRIVERS +#if ENABLED(Z_DUAL_STEPPER_DRIVERS) + //#define Z_DUAL_ENDSTOPS + #if ENABLED(Z_DUAL_ENDSTOPS) + #define Z2_USE_ENDSTOP _XMAX_ + #define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Z_TRIPLE_STEPPER_DRIVERS +#if ENABLED(Z_TRIPLE_STEPPER_DRIVERS) + //#define Z_TRIPLE_ENDSTOPS + #if ENABLED(Z_TRIPLE_ENDSTOPS) + #define Z2_USE_ENDSTOP _XMAX_ + #define Z3_USE_ENDSTOP _YMAX_ + #define Z_TRIPLE_ENDSTOPS_ADJUSTMENT2 0 + #define Z_TRIPLE_ENDSTOPS_ADJUSTMENT3 0 + #endif +#endif + +/** + * Dual X Carriage + * + * This setup has two X carriages that can move independently, each with its own hotend. + * The carriages can be used to print an object with two colors or materials, or in + * "duplication mode" it can print two identical or X-mirrored objects simultaneously. + * The inactive carriage is parked automatically to prevent oozing. + * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. + * By default the X2 stepper is assigned to the first unused E plug on the board. + * + * The following Dual X Carriage modes can be selected with M605 S: + * + * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel + * results as long as it supports dual X-carriages. (M605 S0) + * + * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so + * that additional slicer support is not required. (M605 S1) + * + * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with + * the first X-carriage and extruder, to print 2 copies of the same object at the same time. + * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and + * follow with M605 S2 to initiate duplicated movement. + * + * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates + * the movement of the first except the second extruder is reversed in the X axis. + * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and + * follow with M605 S3 to initiate mirrored movement. + */ +//#define DUAL_X_CARRIAGE +#if ENABLED(DUAL_X_CARRIAGE) + #define X1_MIN_POS X_MIN_POS // Set to X_MIN_POS + #define X1_MAX_POS X_BED_SIZE // Set a maximum so the first X-carriage can't hit the parked second X-carriage + #define X2_MIN_POS 80 // Set a minimum to ensure the second X-carriage can't hit the parked first X-carriage + #define X2_MAX_POS 353 // Set this to the distance between toolheads when both heads are homed + #define X2_HOME_DIR 1 // Set to 1. The second X-carriage always homes to the maximum endstop position + #define X2_HOME_POS X2_MAX_POS // Default X2 home position. Set to X2_MAX_POS. + // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software + // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops + // without modifying the firmware (through the "M218 T1 X???" command). + // Remember: you should set the second extruder x-offset to 0 in your slicer. + + // This is the default power-up mode which can be later using M605. + #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_AUTO_PARK_MODE + + // Default x offset in duplication mode (typically set to half print bed width) + #define DEFAULT_DUPLICATION_X_OFFSET 100 + +#endif // DUAL_X_CARRIAGE + +// Activate a solenoid on the active extruder with M380. Disable all with M381. +// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid. +//#define EXT_SOLENOID + +// @section homing + +// Homing hits each endstop, retracts by these distances, then does a slower bump. +#define X_HOME_BUMP_MM 5 +#define Y_HOME_BUMP_MM 5 +#define Z_HOME_BUMP_MM 2 +#define HOMING_BUMP_DIVISOR { 2, 2, 4 } // Re-Bump Speed Divisor (Divides the Homing Feedrate) +#define QUICK_HOME // If homing includes X and Y, do a diagonal move initially +//#define HOMING_BACKOFF_MM { 2, 2, 2 } // (mm) Move away from the endstops after homing + +// When G28 is called, this option will make Y home before X +//#define HOME_Y_BEFORE_X + +// Enable this if X or Y can't home without homing the other axis first. +//#define CODEPENDENT_XY_HOMING + +#if ENABLED(BLTOUCH) + /** + * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES + * Do not activate settings that the probe might not understand. Clones might misunderstand + * advanced commands. + * + * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then + * check the wiring of the BROWN, RED and ORANGE wires. + * + * Note: If the trigger signal of your probe is not being recognized, it has been very often + * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable" + * like they would be with a real switch. So please check the wiring first. + * + * Settings for all BLTouch and clone probes: + */ + + // Safety: The probe needs time to recognize the command. + // Minimum command delay (ms). Enable and increase if needed. + //#define BLTOUCH_DELAY 500 + + /** + * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones: + */ + + // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful + // in special cases, like noisy or filtered input configurations. + //#define BLTOUCH_FORCE_SW_MODE + + /** + * Settings for BLTouch Smart 3.0 and 3.1 + * Summary: + * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes + * - High-Speed mode + * - Disable LCD voltage options + */ + + /** + * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller! + * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup. + * If disabled, OD mode is the hard-coded default on 3.0 + * On startup, Marlin will compare its eeprom to this vale. If the selected mode + * differs, a mode set eeprom write will be completed at initialization. + * Use the option below to force an eeprom write to a V3.1 probe regardless. + */ + //#define BLTOUCH_SET_5V_MODE + + /** + * Safety: Activate if connecting a probe with an unknown voltage mode. + * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0 + * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write ) + * To preserve the life of the probe, use this once then turn it off and re-flash. + */ + //#define BLTOUCH_FORCE_MODE_SET + + /** + * Use "HIGH SPEED" mode for probing. + * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems. + * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function + * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state. + */ + //#define BLTOUCH_HS_MODE + + // Safety: Enable voltage mode settings in the LCD menu. + //#define BLTOUCH_LCD_VOLTAGE_MENU + +#endif // BLTOUCH + +/** + * Z Steppers Auto-Alignment + * Add the G34 command to align multiple Z steppers using a bed probe. + */ +//#define Z_STEPPER_AUTO_ALIGN +#if ENABLED(Z_STEPPER_AUTO_ALIGN) + // Define probe X and Y positions for Z1, Z2 [, Z3] + #define Z_STEPPER_ALIGN_X { 10, 150, 290 } + #define Z_STEPPER_ALIGN_Y { 290, 10, 290 } + // Set number of iterations to align + #define Z_STEPPER_ALIGN_ITERATIONS 3 + // Enable to restore leveling setup after operation + #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + + // Use the amplification factor to de-/increase correction step. + // In case the stepper (spindle) position is further out than the test point + // Use a value > 1. NOTE: This may cause instability + #define Z_STEPPER_ALIGN_AMP 1.0 + // Stop criterion. If the accuracy is better than this stop iterating early + #define Z_STEPPER_ALIGN_ACC 0.02 +#endif + +// @section machine + +#define AXIS_RELATIVE_MODES { false, false, false, false } + +// Add a Duplicate option for well-separated conjoined nozzles +//#define MULTI_NOZZLE_DUPLICATION + +// By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step. +#define INVERT_X_STEP_PIN false +#define INVERT_Y_STEP_PIN false +#define INVERT_Z_STEP_PIN false +#define INVERT_E_STEP_PIN false + +// Default stepper release if idle. Set to 0 to deactivate. +// Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true. +// Time can be set by M18 and M84. +#define DEFAULT_STEPPER_DEACTIVE_TIME 120 +#define DISABLE_INACTIVE_X true +#define DISABLE_INACTIVE_Y true +#define DISABLE_INACTIVE_Z true // Set to false if the nozzle will fall down on your printed part when print has finished. +#define DISABLE_INACTIVE_E true + +#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate +#define DEFAULT_MINTRAVELFEEDRATE 0.0 + +//#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated + +// @section lcd + +#if EITHER(ULTIPANEL, EXTENSIBLE_UI) + #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #if ENABLED(ULTIPANEL) + #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" + #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen + #endif +#endif + +// @section extras + +// minimum time in microseconds that a movement needs to take if the buffer is emptied. +#define DEFAULT_MINSEGMENTTIME 20000 + +// If defined the movements slow down when the look ahead buffer is only half full +#define SLOWDOWN + +// Frequency limit +// See nophead's blog for more info +// Not working O +//#define XY_FREQUENCY_LIMIT 15 + +// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end +// of the buffer and all stops. This should not be much greater than zero and should only be changed +// if unwanted behavior is observed on a user's machine when running at very slow speeds. +#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s) + +// +// Backlash Compensation +// Adds extra movement to axes on direction-changes to account for backlash. +// +//#define BACKLASH_COMPENSATION +#if ENABLED(BACKLASH_COMPENSATION) + // Define values for backlash distance and correction. + // If BACKLASH_GCODE is enabled these values are the defaults. + #define BACKLASH_DISTANCE_MM { 0, 0, 0 } // (mm) + #define BACKLASH_CORRECTION 0.0 // 0.0 = no correction; 1.0 = full correction + + // Set BACKLASH_SMOOTHING_MM to spread backlash correction over multiple segments + // to reduce print artifacts. (Enabling this is costly in memory and computation!) + //#define BACKLASH_SMOOTHING_MM 3 // (mm) + + // Add runtime configuration and tuning of backlash values (M425) + //#define BACKLASH_GCODE + + #if ENABLED(BACKLASH_GCODE) + // Measure the Z backlash when probing (G29) and set with "M425 Z" + #define MEASURE_BACKLASH_WHEN_PROBING + + #if ENABLED(MEASURE_BACKLASH_WHEN_PROBING) + // When measuring, the probe will move up to BACKLASH_MEASUREMENT_LIMIT + // mm away from point of contact in BACKLASH_MEASUREMENT_RESOLUTION + // increments while checking for the contact to be broken. + #define BACKLASH_MEASUREMENT_LIMIT 0.5 // (mm) + #define BACKLASH_MEASUREMENT_RESOLUTION 0.005 // (mm) + #define BACKLASH_MEASUREMENT_FEEDRATE Z_PROBE_SPEED_SLOW // (mm/m) + #endif + #endif +#endif + +/** + * Automatic backlash, position and hotend offset calibration + * + * Enable G425 to run automatic calibration using an electrically- + * conductive cube, bolt, or washer mounted on the bed. + * + * G425 uses the probe to touch the top and sides of the calibration object + * on the bed and measures and/or correct positional offsets, axis backlash + * and hotend offsets. + * + * Note: HOTEND_OFFSET and CALIBRATION_OBJECT_CENTER must be set to within + * ±5mm of true values for G425 to succeed. + */ +//#define CALIBRATION_GCODE +#if ENABLED(CALIBRATION_GCODE) + + #define CALIBRATION_MEASUREMENT_RESOLUTION 0.01 // mm + + #define CALIBRATION_FEEDRATE_SLOW 60 // mm/m + #define CALIBRATION_FEEDRATE_FAST 1200 // mm/m + #define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/m + + // The following parameters refer to the conical section of the nozzle tip. + #define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm + #define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm + + // Uncomment to enable reporting (required for "G425 V", but consumes PROGMEM). + //#define CALIBRATION_REPORTING + + // The true location and dimension the cube/bolt/washer on the bed. + #define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0} // mm + #define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0} // mm + + // Comment out any sides which are unreachable by the probe. For best + // auto-calibration results, all sides must be reachable. + #define CALIBRATION_MEASURE_RIGHT + #define CALIBRATION_MEASURE_FRONT + #define CALIBRATION_MEASURE_LEFT + #define CALIBRATION_MEASURE_BACK + + // Probing at the exact top center only works if the center is flat. If + // probing on a screwhead or hollow washer, probe near the edges. + //#define CALIBRATION_MEASURE_AT_TOP_EDGES + + // Define pin which is read during calibration + #ifndef CALIBRATION_PIN + #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop + #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin + //#define CALIBRATION_PIN_PULLDOWN + #define CALIBRATION_PIN_PULLUP + #endif +#endif + +/** + * Adaptive Step Smoothing increases the resolution of multi-axis moves, particularly at step frequencies + * below 1kHz (for AVR) or 10kHz (for ARM), where aliasing between axes in multi-axis moves causes audible + * vibration and surface artifacts. The algorithm adapts to provide the best possible step smoothing at the + * lowest stepping frequencies. + */ +//#define ADAPTIVE_STEP_SMOOTHING + +/** + * Custom Microstepping + * Override as-needed for your setup. Up to 3 MS pins are supported. + */ +//#define MICROSTEP1 LOW,LOW,LOW +//#define MICROSTEP2 HIGH,LOW,LOW +//#define MICROSTEP4 LOW,HIGH,LOW +//#define MICROSTEP8 HIGH,HIGH,LOW +//#define MICROSTEP16 LOW,LOW,HIGH +//#define MICROSTEP32 HIGH,LOW,HIGH + +// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU. +#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16] + +/** + * @section stepper motor current + * + * Some boards have a means of setting the stepper motor current via firmware. + * + * The power on motor currents are set by: + * PWM_MOTOR_CURRENT - used by MINIRAMBO & ULTIMAIN_2 + * known compatible chips: A4982 + * DIGIPOT_MOTOR_CURRENT - used by BQ_ZUM_MEGA_3D, RAMBO & SCOOVO_X9H + * known compatible chips: AD5206 + * DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2 + * known compatible chips: MCP4728 + * DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, AZTEEG_X5_MINI_WIFI, MIGHTYBOARD_REVE + * known compatible chips: MCP4451, MCP4018 + * + * Motor currents can also be set by M907 - M910 and by the LCD. + * M907 - applies to all. + * M908 - BQ_ZUM_MEGA_3D, RAMBO, PRINTRBOARD_REVF, RIGIDBOARD_V2 & SCOOVO_X9H + * M909, M910 & LCD - only PRINTRBOARD_REVF & RIGIDBOARD_V2 + */ +//#define PWM_MOTOR_CURRENT { 1300, 1300, 1250 } // Values in milliamps +//#define DIGIPOT_MOTOR_CURRENT { 135,135,135,135,135 } // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A) +//#define DAC_MOTOR_CURRENT_DEFAULT { 70, 80, 90, 80 } // Default drive percent - X, Y, Z, E axis + +// Use an I2C based DIGIPOT (e.g., Azteeg X3 Pro) +//#define DIGIPOT_I2C +#if ENABLED(DIGIPOT_I2C) && !defined(DIGIPOT_I2C_ADDRESS_A) + /** + * Common slave addresses: + * + * A (A shifted) B (B shifted) IC + * Smoothie 0x2C (0x58) 0x2D (0x5A) MCP4451 + * AZTEEG_X3_PRO 0x2C (0x58) 0x2E (0x5C) MCP4451 + * AZTEEG_X5_MINI 0x2C (0x58) 0x2E (0x5C) MCP4451 + * AZTEEG_X5_MINI_WIFI 0x58 0x5C MCP4451 + * MIGHTYBOARD_REVE 0x2F (0x5E) MCP4018 + */ + #define DIGIPOT_I2C_ADDRESS_A 0x2C // unshifted slave address for first DIGIPOT + #define DIGIPOT_I2C_ADDRESS_B 0x2D // unshifted slave address for second DIGIPOT +#endif + +//#define DIGIPOT_MCP4018 // Requires library from https://github.com/stawel/SlowSoftI2CMaster +#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8 MKS SBASE: 5 +// Actual motor currents in Amps. The number of entries must match DIGIPOT_I2C_NUM_CHANNELS. +// These correspond to the physical drivers, so be mindful if the order is changed. +#define DIGIPOT_I2C_MOTOR_CURRENTS { 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0 } // AZTEEG_X3_PRO + +//=========================================================================== +//=============================Additional Features=========================== +//=========================================================================== + +// @section lcd + +// Change values more rapidly when the encoder is rotated faster +#define ENCODER_RATE_MULTIPLIER +#if ENABLED(ENCODER_RATE_MULTIPLIER) + #define ENCODER_10X_STEPS_PER_SEC 30 // (steps/s) Encoder rate for 10x speed + #define ENCODER_100X_STEPS_PER_SEC 80 // (steps/s) Encoder rate for 100x speed +#endif + +// Play a beep when the feedrate is changed from the Status Screen +//#define BEEP_ON_FEEDRATE_CHANGE +#if ENABLED(BEEP_ON_FEEDRATE_CHANGE) + #define FEEDRATE_CHANGE_BEEP_DURATION 10 + #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 +#endif + +// Include a page of printer information in the LCD Main Menu +#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif + +// Scroll a longer status message into view +#define STATUS_MESSAGE_SCROLLING + +// On the Info Screen, display XY with one decimal place when possible +//#define LCD_DECIMAL_SMALL_XY + +// The timeout (in ms) to return to the status screen from sub-menus +//#define LCD_TIMEOUT_TO_STATUS 15000 + +// Add an 'M73' G-code to set the current percentage +#define LCD_SET_PROGRESS_MANUALLY + +#if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS + //#define LCD_PROGRESS_BAR // Show a progress bar on HD44780 LCDs for SD printing + #if ENABLED(LCD_PROGRESS_BAR) + #define PROGRESS_BAR_BAR_TIME 2000 // (ms) Amount of time to show the bar + #define PROGRESS_BAR_MSG_TIME 3000 // (ms) Amount of time to show the status message + #define PROGRESS_MSG_EXPIRE 0 // (ms) Amount of time to retain the status message (0=forever) + //#define PROGRESS_MSG_ONCE // Show the message for MSG_TIME then clear it + //#define LCD_PROGRESS_BAR_TEST // Add a menu item to test the progress bar + #endif +#endif + +/** + * LED Control Menu + * Enable this feature to add LED Control to the LCD menu + */ +//#define LED_CONTROL_MENU +#if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif +#endif // LED_CONTROL_MENU + +#if ENABLED(SDSUPPORT) + + // Some RAMPS and other boards don't detect when an SD card is inserted. You can work + // around this by connecting a push button or single throw switch to the pin defined + // as SD_DETECT_PIN in your board's pins definitions. + // This setting should be disabled unless you are using a push button, pulling the pin to ground. + // Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER). + #define SD_DETECT_INVERTED + + #define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished + #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place. + + // Reverse SD sort to show "more recent" files first, according to the card's FAT. + // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended. + #define SDCARD_RATHERRECENTFIRST + + #define SD_MENU_CONFIRM_START // Confirm the selected SD file before printing + + //#define MENU_ADDAUTOSTART // Add a menu option to run auto#.g files + + #define EVENT_GCODE_SD_STOP "G28XY" // G-code to run on Stop Print (e.g., "G28XY" or "G27") + + /** + * Continue after Power-Loss (Creality3D) + * + * Store the current state to the SD Card at the start of each layer + * during SD printing. If the recovery file is found at boot time, present + * an option on the LCD screen to continue the print from the last-known + * point in the file. + */ + //#define POWER_LOSS_RECOVERY + #if ENABLED(POWER_LOSS_RECOVERY) + //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume + //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. + + // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, + // especially with "vase mode" printing. Set too high and vases cannot be continued. + #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + #endif + + /** + * Sort SD file listings in alphabetical order. + * + * With this option enabled, items on SD cards will be sorted + * by name for easier navigation. + * + * By default... + * + * - Use the slowest -but safest- method for sorting. + * - Folders are sorted to the top. + * - The sort key is statically allocated. + * - No added G-code (M34) support. + * - 40 item sorting limit. (Items after the first 40 are unsorted.) + * + * SD sorting uses static allocation (as set by SDSORT_LIMIT), allowing the + * compiler to calculate the worst-case usage and throw an error if the SRAM + * limit is exceeded. + * + * - SDSORT_USES_RAM provides faster sorting via a static directory buffer. + * - SDSORT_USES_STACK does the same, but uses a local stack-based buffer. + * - SDSORT_CACHE_NAMES will retain the sorted file listing in RAM. (Expensive!) + * - SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible. (Use with caution!) + */ + #define SDCARD_SORT_ALPHA + + // SD Card Sorting options + #if ENABLED(SDCARD_SORT_ALPHA) + #define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). Costs 27 bytes each. + #define FOLDER_SORTING -1 // -1=above 0=none 1=below + #define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 g-code. + #define SDSORT_USES_RAM false // Pre-allocate a static array for faster pre-sorting. + #define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.) + #define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option. + #define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use! + #define SDSORT_CACHE_VFATS 2 // Maximum number of 13-byte VFAT entries to use for sorting. + // Note: Only affects SCROLL_LONG_FILENAMES with SDSORT_CACHE_NAMES but not SDSORT_DYNAMIC_RAM. + #endif + + // This allows hosts to request long names for files and folders with M33 + #define LONG_FILENAME_HOST_SUPPORT + + // Enable this option to scroll long filenames in the SD card menu + #define SCROLL_LONG_FILENAMES + + // Leave the heaters on after Stop Print (not recommended!) + //#define SD_ABORT_NO_COOLDOWN + + /** + * This option allows you to abort SD printing when any endstop is triggered. + * This feature must be enabled with "M540 S1" or from the LCD menu. + * To have any effect, endstops must be enabled during SD printing. + */ + //#define SD_ABORT_ON_ENDSTOP_HIT + + /** + * This option makes it easier to print the same SD Card file again. + * On print completion the LCD Menu will open with the file selected. + * You can just click to start the print, or navigate elsewhere. + */ + //#define SD_REPRINT_LAST_SELECTED_FILE + + /** + * Auto-report SdCard status with M27 S + */ + //#define AUTO_REPORT_SD_STATUS + + /** + * Support for USB thumb drives using an Arduino USB Host Shield or + * equivalent MAX3421E breakout board. The USB thumb drive will appear + * to Marlin as an SD card. + * + * The MAX3421E must be assigned the same pins as the SD card reader, with + * the following pin mapping: + * + * SCLK, MOSI, MISO --> SCLK, MOSI, MISO + * INT --> SD_DETECT_PIN + * SS --> SDSS + */ + //#define USB_FLASH_DRIVE_SUPPORT + #if ENABLED(USB_FLASH_DRIVE_SUPPORT) + #define USB_CS_PIN SDSS + #define USB_INTR_PIN SD_DETECT_PIN + #endif + + /** + * When using a bootloader that supports SD-Firmware-Flashing, + * add a menu item to activate SD-FW-Update on the next reboot. + * + * Requires ATMEGA2560 (Arduino Mega) + * + * Tested with this bootloader: + * https://github.com/FleetProbe/MicroBridge-Arduino-ATMega2560 + */ + //#define SD_FIRMWARE_UPDATE + #if ENABLED(SD_FIRMWARE_UPDATE) + #define SD_FIRMWARE_UPDATE_EEPROM_ADDR 0x1FF + #define SD_FIRMWARE_UPDATE_ACTIVE_VALUE 0xF0 + #define SD_FIRMWARE_UPDATE_INACTIVE_VALUE 0xFF + #endif + + // Add an optimized binary file transfer mode, initiated with 'M28 B1' + //#define BINARY_FILE_TRANSFER + + #if HAS_SDCARD_CONNECTION + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD + #endif + +#endif // SDSUPPORT + +/** + * By default an onboard SD card reader may be shared as a USB mass- + * storage device. This option hides the SD card from the host PC. + */ +//#define NO_SD_HOST_DRIVE // Disable SD Card access over USB (for security). + +/** + * Additional options for Graphical Displays + * + * Use the optimizations here to improve printing performance, + * which can be adversely affected by graphical display drawing, + * especially when doing several short moves, and when printing + * on DELTA and SCARA machines. + * + * Some of these options may result in the display lagging behind + * controller events, as there is a trade-off between reliable + * printing performance versus fast display updates. + */ +#if HAS_GRAPHICAL_LCD + // Show SD percentage next to the progress bar + //#define DOGM_SD_PERCENT + + // Enable to save many cycles by drawing a hollow frame on the Info Screen + #define XYZ_HOLLOW_FRAME + + // Enable to save many cycles by drawing a hollow frame on Menu Screens + #define MENU_HOLLOW_FRAME + + // A bigger font is available for edit items. Costs 3120 bytes of PROGMEM. + // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. + #define USE_BIG_EDIT_FONT + + // A smaller font may be used on the Info Screen. Costs 2300 bytes of PROGMEM. + // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. + //#define USE_SMALL_INFOFONT + + // Enable this option and reduce the value to optimize screen updates. + // The normal delay is 10µs. Use the lowest value that still gives a reliable display. + //#define DOGM_SPI_DELAY_US 5 + + // Swap the CW/CCW indicators in the graphics overlay + //#define OVERLAY_GFX_REVERSE + + /** + * ST7920-based LCDs can emulate a 16 x 4 character display using + * the ST7920 character-generator for very fast screen updates. + * Enable LIGHTWEIGHT_UI to use this special display mode. + * + * Since LIGHTWEIGHT_UI has limited space, the position and status + * message occupy the same line. Set STATUS_EXPIRE_SECONDS to the + * length of time to display the status message before clearing. + * + * Set STATUS_EXPIRE_SECONDS to zero to never clear the status. + * This will prevent position updates from being displayed. + */ + #if ENABLED(U8GLIB_ST7920) + //#define LIGHTWEIGHT_UI + #if ENABLED(LIGHTWEIGHT_UI) + #define STATUS_EXPIRE_SECONDS 20 + #endif + #endif + + /** + * Status (Info) Screen customizations + * These options may affect code size and screen render time. + * Custom status screens can forcibly override these settings. + */ + //#define STATUS_COMBINE_HEATERS // Use combined heater images instead of separate ones + //#define STATUS_HOTEND_NUMBERLESS // Use plain hotend icons instead of numbered ones (with 2+ hotends) + #define STATUS_HOTEND_INVERTED // Show solid nozzle bitmaps when heating (Requires STATUS_HOTEND_ANIM) + #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating + #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating + #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap + //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap + //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames + #define STATUS_HEAT_PERCENT // Show heating in a progress bar + //#define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash) + + // Frivolous Game Options + //#define MARLIN_BRICKOUT + //#define MARLIN_INVADERS + //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu + +#endif // HAS_GRAPHICAL_LCD + +// @section safety + +/** + * The watchdog hardware timer will do a reset and disable all outputs + * if the firmware gets too overloaded to read the temperature sensors. + * + * If you find that watchdog reboot causes your AVR board to hang forever, + * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO. + * NOTE: This method is less reliable as it can only catch hangups while + * interrupts are enabled. + */ +#define USE_WATCHDOG +#if ENABLED(USE_WATCHDOG) + //#define WATCHDOG_RESET_MANUAL +#endif + +// @section lcd + +/** + * Babystepping enables movement of the axes by tiny increments without changing + * the current position values. This feature is used primarily to adjust the Z + * axis in the first layer of a print in real-time. + * + * Warning: Does not respect endstops! + */ +#define BABYSTEPPING +#if ENABLED(BABYSTEPPING) + //#define BABYSTEP_WITHOUT_HOMING + //#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA! + #define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way + #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion. + + #define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping. + #if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING) + #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds. + // Note: Extra time may be added to mitigate controller latency. + //#define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement). + //#define MOVE_Z_WHEN_IDLE // Jump to the move Z menu on doubleclick when printer is idle. + #if ENABLED(MOVE_Z_WHEN_IDLE) + #define MOVE_Z_IDLE_MULTIPLICATOR 1 // Multiply 1mm by this factor for the move step size. + #endif + #endif + + //#define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28 + + //#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping + #if ENABLED(BABYSTEP_ZPROBE_OFFSET) + //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets + //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor + #endif +#endif + +// @section extruder + +/** + * Linear Pressure Control v1.5 + * + * Assumption: advance [steps] = k * (delta velocity [steps/s]) + * K=0 means advance disabled. + * + * NOTE: K values for LIN_ADVANCE 1.5 differ from earlier versions! + * + * Set K around 0.22 for 3mm PLA Direct Drive with ~6.5cm between the drive gear and heatbreak. + * Larger K values will be needed for flexible filament and greater distances. + * If this algorithm produces a higher speed offset than the extruder can handle (compared to E jerk) + * print acceleration will be reduced during the affected moves to keep within the limit. + * + * See http://marlinfw.org/docs/features/lin_advance.html for full instructions. + * Mention @Sebastianv650 on GitHub to alert the author of any issues. + */ +//#define LIN_ADVANCE +#if ENABLED(LIN_ADVANCE) + //#define EXTRA_LIN_ADVANCE_K // Enable for second linear advance constants + #define LIN_ADVANCE_K 0.22 // Unit: mm compression per 1mm/s extruder speed + //#define LA_DEBUG // If enabled, this will generate debug information output over USB. +#endif + +// @section leveling + +#if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL) + // Override the mesh area if the automatic (max) area is too large + //#define MESH_MIN_X MESH_INSET + //#define MESH_MIN_Y MESH_INSET + //#define MESH_MAX_X X_BED_SIZE - (MESH_INSET) + //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET) +#endif + +/** + * Repeatedly attempt G29 leveling until it succeeds. + * Stop after G29_MAX_RETRIES attempts. + */ +//#define G29_RETRY_AND_RECOVER +#if ENABLED(G29_RETRY_AND_RECOVER) + #define G29_MAX_RETRIES 3 + #define G29_HALT_ON_FAILURE + /** + * Specify the GCODE commands that will be executed when leveling succeeds, + * between attempts, and after the maximum number of retries have been tried. + */ + #define G29_SUCCESS_COMMANDS "M117 Bed leveling done." + #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0" + #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1" + +#endif + +// @section extras + +// +// G2/G3 Arc Support +// +#define ARC_SUPPORT // Disable this feature to save ~3226 bytes +#if ENABLED(ARC_SUPPORT) + #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles + //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes +#endif + +// Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes. +//#define BEZIER_CURVE_SUPPORT + +/** + * G38 Probe Target + * + * This option adds G38.2 and G38.3 (probe towards target) + * and optionally G38.4 and G38.5 (probe away from target). + * Set MULTIPLE_PROBING for G38 to probe more than once. + */ +//#define G38_PROBE_TARGET +#if ENABLED(G38_PROBE_TARGET) + //#define G38_PROBE_AWAY // Include G38.4 and G38.5 to probe away from target + #define G38_MINIMUM_MOVE 0.0275 // (mm) Minimum distance that will produce a move. +#endif + +// Moves (or segments) with fewer steps than this will be joined with the next move +#define MIN_STEPS_PER_SEGMENT 6 + +/** + * Minimum delay after setting the stepper DIR (in ns) + * 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire) + * 20 : Minimum for TMC2xxx drivers + * 200 : Minimum for A4988 drivers + * 400 : Minimum for A5984 drivers + * 500 : Minimum for LV8729 drivers (guess, no info in datasheet) + * 650 : Minimum for DRV8825 drivers + * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet) + * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet) + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MINIMUM_STEPPER_DIR_DELAY 650 + +/** + * Minimum stepper driver pulse width (in µs) + * 0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers + * 0 : Minimum 500ns for LV8729, adjusted in stepper.h + * 1 : Minimum for A4988 and A5984 stepper drivers + * 2 : Minimum for DRV8825 stepper drivers + * 3 : Minimum for TB6600 stepper drivers + * 30 : Minimum for TB6560 stepper drivers + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MINIMUM_STEPPER_PULSE 2 + +/** + * Maximum stepping rate (in Hz) the stepper driver allows + * If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE) + * 500000 : Maximum for A4988 stepper driver + * 400000 : Maximum for TMC2xxx stepper drivers + * 250000 : Maximum for DRV8825 stepper driver + * 200000 : Maximum for LV8729 stepper driver + * 150000 : Maximum for TB6600 stepper driver + * 15000 : Maximum for TB6560 stepper driver + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MAXIMUM_STEPPER_RATE 250000 + +// @section temperature + +// Control heater 0 and heater 1 in parallel. +//#define HEATERS_PARALLEL + +//=========================================================================== +//================================= Buffers ================================= +//=========================================================================== + +// @section hidden + +// The number of linear motions that can be in the plan at any give time. +// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2 (e.g. 8, 16, 32) because shifts and ors are used to do the ring-buffering. +#if ENABLED(SDSUPPORT) + #define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller +#else + #define BLOCK_BUFFER_SIZE 16 // maximize block buffer +#endif + +// @section serial + +// The ASCII buffer for serial input +#define MAX_CMD_SIZE 96 +#define BUFSIZE 4 + +// Transmission to Host Buffer Size +// To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0. +// To buffer a simple "ok" you need 4 bytes. +// For ADVANCED_OK (M105) you need 32 bytes. +// For debug-echo: 128 bytes for the optimal speed. +// Other output doesn't need to be that speedy. +// :[0, 2, 4, 8, 16, 32, 64, 128, 256] +#define TX_BUFFER_SIZE 0 + +// Host Receive Buffer Size +// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough. +// To use flow control, set this buffer size to at least 1024 bytes. +// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048] +//#define RX_BUFFER_SIZE 1024 + +#if RX_BUFFER_SIZE >= 1024 + // Enable to have the controller send XON/XOFF control characters to + // the host to signal the RX buffer is becoming full. + //#define SERIAL_XON_XOFF +#endif + +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + +#if ENABLED(SDSUPPORT) + // Enable this option to collect and display the maximum + // RX queue usage after transferring a file to SD. + //#define SERIAL_STATS_MAX_RX_QUEUED + + // Enable this option to collect and display the number + // of dropped bytes after a file transfer to SD. + //#define SERIAL_STATS_DROPPED_RX +#endif + +// Enable an emergency-command parser to intercept certain commands as they +// enter the serial receive buffer, so they cannot be blocked. +// Currently handles M108, M112, M410 +// Does not work on boards using AT90USB (USBCON) processors! +//#define EMERGENCY_PARSER + +// Bad Serial-connections can miss a received command by sending an 'ok' +// Therefore some clients abort after 30 seconds in a timeout. +// Some other clients start sending commands while receiving a 'wait'. +// This "wait" is only sent when the buffer is empty. 1 second is a good value here. +//#define NO_TIMEOUTS 1000 // Milliseconds + +// Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary. +//#define ADVANCED_OK + +// Printrun may have trouble receiving long strings all at once. +// This option inserts short delays between lines of serial output. +#define SERIAL_OVERRUN_PROTECTION + +// @section extras + +/** + * Extra Fan Speed + * Adds a secondary fan speed for each print-cooling fan. + * 'M106 P T3-255' : Set a secondary speed for + * 'M106 P T2' : Use the set secondary speed + * 'M106 P T1' : Restore the previous fan speed + */ +//#define EXTRA_FAN_SPEED + +/** + * Firmware-based and LCD-controlled retract + * + * Add G10 / G11 commands for automatic firmware-based retract / recover. + * Use M207 and M208 to define parameters for retract / recover. + * + * Use M209 to enable or disable auto-retract. + * With auto-retract enabled, all G1 E moves within the set range + * will be converted to firmware-based retract/recover moves. + * + * Be sure to turn off auto-retract during filament change. + * + * Note that M207 / M208 / M209 settings are saved to EEPROM. + * + */ +//#define FWRETRACT +#if ENABLED(FWRETRACT) + #define FWRETRACT_AUTORETRACT // costs ~500 bytes of PROGMEM + #if ENABLED(FWRETRACT_AUTORETRACT) + #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over + #define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion + #endif + #define RETRACT_LENGTH 3 // Default retract length (positive mm) + #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change + #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) + #define RETRACT_ZRAISE 0 // Default retract Z-raise (mm) + #define RETRACT_RECOVER_LENGTH 0 // Default additional recover length (mm, added to retract length when recovering) + #define RETRACT_RECOVER_LENGTH_SWAP 0 // Default additional swap recover length (mm, added to retract length when recovering from extruder change) + #define RETRACT_RECOVER_FEEDRATE 8 // Default feedrate for recovering from retraction (mm/s) + #define RETRACT_RECOVER_FEEDRATE_SWAP 8 // Default feedrate for recovering from swap retraction (mm/s) + #if ENABLED(MIXING_EXTRUDER) + //#define RETRACT_SYNC_MIXING // Retract and restore all mixing steppers simultaneously + #endif +#endif + +/** + * Universal tool change settings. + * Applies to all types of extruders except where explicitly noted. + */ +#if EXTRUDERS > 1 + // Z raise distance for tool-change, as needed for some extruders + #define TOOLCHANGE_ZRAISE 2 // (mm) + //#define TOOLCHANGE_NO_RETURN // Never return to the previous position on tool-change + + // Retract and prime filament on tool-change + //#define TOOLCHANGE_FILAMENT_SWAP + #if ENABLED(TOOLCHANGE_FILAMENT_SWAP) + #define TOOLCHANGE_FIL_SWAP_LENGTH 12 // (mm) + #define TOOLCHANGE_FIL_EXTRA_PRIME 2 // (mm) + #define TOOLCHANGE_FIL_SWAP_RETRACT_SPEED 3600 // (mm/m) + #define TOOLCHANGE_FIL_SWAP_PRIME_SPEED 3600 // (mm/m) + #endif + + /** + * Position to park head during tool change. + * Doesn't apply to SWITCHING_TOOLHEAD, DUAL_X_CARRIAGE, or PARKING_EXTRUDER + */ + //#define TOOLCHANGE_PARK + #if ENABLED(TOOLCHANGE_PARK) + #define TOOLCHANGE_PARK_XY { X_MIN_POS + 10, Y_MIN_POS + 10 } + #define TOOLCHANGE_PARK_XY_FEEDRATE 6000 // (mm/m) + #endif +#endif + +/** + * Advanced Pause + * Experimental feature for filament change support and for parking the nozzle when paused. + * Adds the GCode M600 for initiating filament change. + * If PARK_HEAD_ON_PAUSE enabled, adds the GCode M125 to pause printing and park the nozzle. + * + * Requires an LCD display. + * Requires NOZZLE_PARK_FEATURE. + * This feature is required for the default FILAMENT_RUNOUT_SCRIPT. + */ +#define ADVANCED_PAUSE_FEATURE +#if ENABLED(ADVANCED_PAUSE_FEATURE) + #define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate. + #define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract. + // This short retract is done immediately, before parking the nozzle. + #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast. + #define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. + #define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload. + // For Bowden, the full length of the tube and nozzle. + // For direct drive, the full length of the nozzle. + // Set to 0 for manual unloading. + #define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load. + #define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material. + // 0 to disable start loading and skip to fast load only + #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast. + #define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. + #define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle. + // For Bowden, the full length of the tube and nozzle. + // For direct drive, the full length of the nozzle. + //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted. + #define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate. + #define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading. + // Set to 0 for manual extrusion. + // Filament can be extruded repeatedly from the Filament Change menu + // until extrusion is consistent, and to purge old filament. + #define ADVANCED_PAUSE_RESUME_PRIME 0 // (mm) Extra distance to prime nozzle after returning from park. + //#define ADVANCED_PAUSE_FANS_PAUSE // Turn off print-cooling fans while the machine is paused. + + // Filament Unload does a Retract, Delay, and Purge first: + #define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length. + #define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract. + #define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged. + + #define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety. + #define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed. + #define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change. + + //#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change. + //#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change + + //#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu. + //#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302) +#endif + +// @section tmc + +/** + * TMC26X Stepper Driver options + * + * The TMC26XStepper library is required for this stepper driver. + * https://github.com/trinamic/TMC26XStepper + */ +#if HAS_DRIVER(TMC26X) + + #if AXIS_DRIVER_TYPE_X(TMC26X) + #define X_MAX_CURRENT 1000 // (mA) + #define X_SENSE_RESISTOR 91 // (mOhms) + #define X_MICROSTEPS 16 // Number of microsteps + #endif + + #if AXIS_DRIVER_TYPE_X2(TMC26X) + #define X2_MAX_CURRENT 1000 + #define X2_SENSE_RESISTOR 91 + #define X2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Y(TMC26X) + #define Y_MAX_CURRENT 1000 + #define Y_SENSE_RESISTOR 91 + #define Y_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Y2(TMC26X) + #define Y2_MAX_CURRENT 1000 + #define Y2_SENSE_RESISTOR 91 + #define Y2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z(TMC26X) + #define Z_MAX_CURRENT 1000 + #define Z_SENSE_RESISTOR 91 + #define Z_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z2(TMC26X) + #define Z2_MAX_CURRENT 1000 + #define Z2_SENSE_RESISTOR 91 + #define Z2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z3(TMC26X) + #define Z3_MAX_CURRENT 1000 + #define Z3_SENSE_RESISTOR 91 + #define Z3_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E0(TMC26X) + #define E0_MAX_CURRENT 1000 + #define E0_SENSE_RESISTOR 91 + #define E0_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E1(TMC26X) + #define E1_MAX_CURRENT 1000 + #define E1_SENSE_RESISTOR 91 + #define E1_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E2(TMC26X) + #define E2_MAX_CURRENT 1000 + #define E2_SENSE_RESISTOR 91 + #define E2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E3(TMC26X) + #define E3_MAX_CURRENT 1000 + #define E3_SENSE_RESISTOR 91 + #define E3_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E4(TMC26X) + #define E4_MAX_CURRENT 1000 + #define E4_SENSE_RESISTOR 91 + #define E4_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E5(TMC26X) + #define E5_MAX_CURRENT 1000 + #define E5_SENSE_RESISTOR 91 + #define E5_MICROSTEPS 16 + #endif + +#endif // TMC26X + +// @section tmc_smart + +/** + * To use TMC2130, TMC2160, TMC2660, TMC5130, TMC5160 stepper drivers in SPI mode + * connect your SPI pins to the hardware SPI interface on your board and define + * the required CS pins in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 + * pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.). + * You may also use software SPI if you wish to use general purpose IO pins. + * + * To use TMC2208 stepper UART-configurable stepper drivers connect #_SERIAL_TX_PIN + * to the driver side PDN_UART pin with a 1K resistor. + * To use the reading capabilities, also connect #_SERIAL_RX_PIN to PDN_UART without + * a resistor. + * The drivers can also be used with hardware serial. + * + * TMCStepper library is required to use TMC stepper drivers. + * https://github.com/teemuatlut/TMCStepper + */ +#if HAS_TRINAMIC + + #define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current + #define INTERPOLATE true // Interpolate X/Y/Z_MICROSTEPS to 256 + + #if AXIS_IS_TMC(X) + #define X_CURRENT 800 // (mA) RMS current. Multiply by 1.414 for peak current. + #define X_MICROSTEPS 16 // 0..256 + #define X_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(X2) + #define X2_CURRENT 800 + #define X2_MICROSTEPS 16 + #define X2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Y) + #define Y_CURRENT 800 + #define Y_MICROSTEPS 16 + #define Y_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Y2) + #define Y2_CURRENT 800 + #define Y2_MICROSTEPS 16 + #define Y2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Z) + #define Z_CURRENT 800 + #define Z_MICROSTEPS 16 + #define Z_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Z2) + #define Z2_CURRENT 800 + #define Z2_MICROSTEPS 16 + #define Z2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Z3) + #define Z3_CURRENT 800 + #define Z3_MICROSTEPS 16 + #define Z3_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E0) + #define E0_CURRENT 800 + #define E0_MICROSTEPS 16 + #define E0_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E1) + #define E1_CURRENT 800 + #define E1_MICROSTEPS 16 + #define E1_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E2) + #define E2_CURRENT 800 + #define E2_MICROSTEPS 16 + #define E2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E3) + #define E3_CURRENT 800 + #define E3_MICROSTEPS 16 + #define E3_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E4) + #define E4_CURRENT 800 + #define E4_MICROSTEPS 16 + #define E4_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E5) + #define E5_CURRENT 800 + #define E5_MICROSTEPS 16 + #define E5_RSENSE 0.11 + #endif + + /** + * Override default SPI pins for TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160 drivers here. + * The default pins can be found in your board's pins file. + */ + //#define X_CS_PIN -1 + //#define Y_CS_PIN -1 + //#define Z_CS_PIN -1 + //#define X2_CS_PIN -1 + //#define Y2_CS_PIN -1 + //#define Z2_CS_PIN -1 + //#define Z3_CS_PIN -1 + //#define E0_CS_PIN -1 + //#define E1_CS_PIN -1 + //#define E2_CS_PIN -1 + //#define E3_CS_PIN -1 + //#define E4_CS_PIN -1 + //#define E5_CS_PIN -1 + + /** + * Software option for SPI driven drivers (TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160). + * The default SW SPI pins are defined the respective pins files, + * but you can override or define them here. + */ + //#define TMC_USE_SW_SPI + //#define TMC_SW_MOSI -1 + //#define TMC_SW_MISO -1 + //#define TMC_SW_SCK -1 + + /** + * Four TMC2209 drivers can use the same HW/SW serial port with hardware configured addresses. + * Set the address using jumpers on pins MS1 and MS2. + * Address | MS1 | MS2 + * 0 | LOW | LOW + * 1 | HIGH | LOW + * 2 | LOW | HIGH + * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. + */ + #define X_SLAVE_ADDRESS 0 + #define Y_SLAVE_ADDRESS 0 + #define Z_SLAVE_ADDRESS 0 + #define X2_SLAVE_ADDRESS 0 + #define Y2_SLAVE_ADDRESS 0 + #define Z2_SLAVE_ADDRESS 0 + #define Z3_SLAVE_ADDRESS 0 + #define E0_SLAVE_ADDRESS 0 + #define E1_SLAVE_ADDRESS 0 + #define E2_SLAVE_ADDRESS 0 + #define E3_SLAVE_ADDRESS 0 + #define E4_SLAVE_ADDRESS 0 + #define E5_SLAVE_ADDRESS 0 + + /** + * Software enable + * + * Use for drivers that do not use a dedicated enable pin, but rather handle the same + * function through a communication line such as SPI or UART. + */ + //#define SOFTWARE_DRIVER_ENABLE + + /** + * TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only + * Use Trinamic's ultra quiet stepping mode. + * When disabled, Marlin will use spreadCycle stepping mode. + */ + #define STEALTHCHOP_XY + #define STEALTHCHOP_Z + #define STEALTHCHOP_E + + /** + * Optimize spreadCycle chopper parameters by using predefined parameter sets + * or with the help of an example included in the library. + * Provided parameter sets are + * CHOPPER_DEFAULT_12V + * CHOPPER_DEFAULT_19V + * CHOPPER_DEFAULT_24V + * CHOPPER_DEFAULT_36V + * CHOPPER_PRUSAMK3_24V // Imported parameters from the official Prusa firmware for MK3 (24V) + * CHOPPER_MARLIN_119 // Old defaults from Marlin v1.1.9 + * + * Define you own with + * { , , hysteresis_start[1..8] } + */ + #define CHOPPER_TIMING CHOPPER_DEFAULT_12V + + /** + * Monitor Trinamic drivers for error conditions, + * like overtemperature and short to ground. + * In the case of overtemperature Marlin can decrease the driver current until error condition clears. + * Other detected conditions can be used to stop the current print. + * Relevant g-codes: + * M906 - Set or get motor current in milliamps using axis codes X, Y, Z, E. Report values if no axis codes given. + * M911 - Report stepper driver overtemperature pre-warn condition. + * M912 - Clear stepper driver overtemperature pre-warn condition flag. + * M122 - Report driver parameters (Requires TMC_DEBUG) + */ + //#define MONITOR_DRIVER_STATUS + + #if ENABLED(MONITOR_DRIVER_STATUS) + #define CURRENT_STEP_DOWN 50 // [mA] + #define REPORT_CURRENT_CHANGE + #define STOP_ON_ERROR + #endif + + /** + * TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only + * The driver will switch to spreadCycle when stepper speed is over HYBRID_THRESHOLD. + * This mode allows for faster movements at the expense of higher noise levels. + * STEALTHCHOP_(XY|Z|E) must be enabled to use HYBRID_THRESHOLD. + * M913 X/Y/Z/E to live tune the setting + */ + //#define HYBRID_THRESHOLD + + #define X_HYBRID_THRESHOLD 100 // [mm/s] + #define X2_HYBRID_THRESHOLD 100 + #define Y_HYBRID_THRESHOLD 100 + #define Y2_HYBRID_THRESHOLD 100 + #define Z_HYBRID_THRESHOLD 3 + #define Z2_HYBRID_THRESHOLD 3 + #define Z3_HYBRID_THRESHOLD 3 + #define E0_HYBRID_THRESHOLD 30 + #define E1_HYBRID_THRESHOLD 30 + #define E2_HYBRID_THRESHOLD 30 + #define E3_HYBRID_THRESHOLD 30 + #define E4_HYBRID_THRESHOLD 30 + #define E5_HYBRID_THRESHOLD 30 + + /** + * TMC2130, TMC2160, TMC2209, TMC2660, TMC5130, and TMC5160 only + * Use StallGuard2 to sense an obstacle and trigger an endstop. + * Connect the stepper driver's DIAG1 pin to the X/Y endstop pin. + * X, Y, and Z homing will always be done in spreadCycle mode. + * + * X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity. + * Higher values make the system LESS sensitive. + * Lower value make the system MORE sensitive. + * Too low values can lead to false positives, while too high values will collide the axis without triggering. + * It is advised to set X/Y/Z_HOME_BUMP_MM to 0. + * M914 X/Y/Z to live tune the setting + */ + //#define SENSORLESS_HOMING // StallGuard capable drivers only + + /** + * Use StallGuard2 to probe the bed with the nozzle. + * + * CAUTION: This could cause damage to machines that use a lead screw or threaded rod + * to move the Z axis. Take extreme care when attempting to enable this feature. + */ + //#define SENSORLESS_PROBING // StallGuard capable drivers only + + #if EITHER(SENSORLESS_HOMING, SENSORLESS_PROBING) + // TMC2209: 0...255. TMC2130: -64...63 + #define X_STALL_SENSITIVITY 8 + #define Y_STALL_SENSITIVITY 8 + //#define Z_STALL_SENSITIVITY 8 + #endif + + /** + * Beta feature! + * Create a 50/50 square wave step pulse optimal for stepper drivers. + */ + //#define SQUARE_WAVE_STEPPING + + /** + * Enable M122 debugging command for TMC stepper drivers. + * M122 S0/1 will enable continous reporting. + */ + //#define TMC_DEBUG + + /** + * You can set your own advanced settings by filling in predefined functions. + * A list of available functions can be found on the library github page + * https://github.com/teemuatlut/TMCStepper + * + * Example: + * #define TMC_ADV() { \ + * stepperX.diag0_temp_prewarn(1); \ + * stepperY.interpolate(0); \ + * } + */ + #define TMC_ADV() { } + +#endif // HAS_TRINAMIC + +// @section L6470 + +/** + * L6470 Stepper Driver options + * + * Arduino-L6470 library (0.7.0 or higher) is required for this stepper driver. + * https://github.com/ameyer/Arduino-L6470 + * + * Requires the following to be defined in your pins_YOUR_BOARD file + * L6470_CHAIN_SCK_PIN + * L6470_CHAIN_MISO_PIN + * L6470_CHAIN_MOSI_PIN + * L6470_CHAIN_SS_PIN + * L6470_RESET_CHAIN_PIN (optional) + */ +#if HAS_DRIVER(L6470) + + //#define L6470_CHITCHAT // Display additional status info + + #if AXIS_DRIVER_TYPE_X(L6470) + #define X_MICROSTEPS 128 // Number of microsteps (VALID: 1, 2, 4, 8, 16, 32, 128) + #define X_OVERCURRENT 2000 // (mA) Current where the driver detects an over current (VALID: 375 x (1 - 16) - 6A max - rounds down) + #define X_STALLCURRENT 1500 // (mA) Current where the driver detects a stall (VALID: 31.25 * (1-128) - 4A max - rounds down) + #define X_MAX_VOLTAGE 127 // 0-255, Maximum effective voltage seen by stepper + #define X_CHAIN_POS 0 // Position in SPI chain, 0=Not in chain, 1=Nearest MOSI + #endif + + #if AXIS_DRIVER_TYPE_X2(L6470) + #define X2_MICROSTEPS 128 + #define X2_OVERCURRENT 2000 + #define X2_STALLCURRENT 1500 + #define X2_MAX_VOLTAGE 127 + #define X2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Y(L6470) + #define Y_MICROSTEPS 128 + #define Y_OVERCURRENT 2000 + #define Y_STALLCURRENT 1500 + #define Y_MAX_VOLTAGE 127 + #define Y_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Y2(L6470) + #define Y2_MICROSTEPS 128 + #define Y2_OVERCURRENT 2000 + #define Y2_STALLCURRENT 1500 + #define Y2_MAX_VOLTAGE 127 + #define Y2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Z(L6470) + #define Z_MICROSTEPS 128 + #define Z_OVERCURRENT 2000 + #define Z_STALLCURRENT 1500 + #define Z_MAX_VOLTAGE 127 + #define Z_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Z2(L6470) + #define Z2_MICROSTEPS 128 + #define Z2_OVERCURRENT 2000 + #define Z2_STALLCURRENT 1500 + #define Z2_MAX_VOLTAGE 127 + #define Z2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Z3(L6470) + #define Z3_MICROSTEPS 128 + #define Z3_OVERCURRENT 2000 + #define Z3_STALLCURRENT 1500 + #define Z3_MAX_VOLTAGE 127 + #define Z3_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E0(L6470) + #define E0_MICROSTEPS 128 + #define E0_OVERCURRENT 2000 + #define E0_STALLCURRENT 1500 + #define E0_MAX_VOLTAGE 127 + #define E0_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E1(L6470) + #define E1_MICROSTEPS 128 + #define E1_OVERCURRENT 2000 + #define E1_STALLCURRENT 1500 + #define E1_MAX_VOLTAGE 127 + #define E1_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E2(L6470) + #define E2_MICROSTEPS 128 + #define E2_OVERCURRENT 2000 + #define E2_STALLCURRENT 1500 + #define E2_MAX_VOLTAGE 127 + #define E2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E3(L6470) + #define E3_MICROSTEPS 128 + #define E3_OVERCURRENT 2000 + #define E3_STALLCURRENT 1500 + #define E3_MAX_VOLTAGE 127 + #define E3_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E4(L6470) + #define E4_MICROSTEPS 128 + #define E4_OVERCURRENT 2000 + #define E4_STALLCURRENT 1500 + #define E4_MAX_VOLTAGE 127 + #define E4_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E5(L6470) + #define E5_MICROSTEPS 128 + #define E5_OVERCURRENT 2000 + #define E5_STALLCURRENT 1500 + #define E5_MAX_VOLTAGE 127 + #define E5_CHAIN_POS 0 + #endif + + /** + * Monitor L6470 drivers for error conditions like over temperature and over current. + * In the case of over temperature Marlin can decrease the drive until the error condition clears. + * Other detected conditions can be used to stop the current print. + * Relevant g-codes: + * M906 - I1/2/3/4/5 Set or get motor drive level using axis codes X, Y, Z, E. Report values if no axis codes given. + * I not present or I0 or I1 - X, Y, Z or E0 + * I2 - X2, Y2, Z2 or E1 + * I3 - Z3 or E3 + * I4 - E4 + * I5 - E5 + * M916 - Increase drive level until get thermal warning + * M917 - Find minimum current thresholds + * M918 - Increase speed until max or error + * M122 S0/1 - Report driver parameters + */ + //#define MONITOR_L6470_DRIVER_STATUS + + #if ENABLED(MONITOR_L6470_DRIVER_STATUS) + #define KVAL_HOLD_STEP_DOWN 1 + //#define L6470_STOP_ON_ERROR + #endif + +#endif // L6470 + +/** + * TWI/I2C BUS + * + * This feature is an EXPERIMENTAL feature so it shall not be used on production + * machines. Enabling this will allow you to send and receive I2C data from slave + * devices on the bus. + * + * ; Example #1 + * ; This macro send the string "Marlin" to the slave device with address 0x63 (99) + * ; It uses multiple M260 commands with one B arg + * M260 A99 ; Target slave address + * M260 B77 ; M + * M260 B97 ; a + * M260 B114 ; r + * M260 B108 ; l + * M260 B105 ; i + * M260 B110 ; n + * M260 S1 ; Send the current buffer + * + * ; Example #2 + * ; Request 6 bytes from slave device with address 0x63 (99) + * M261 A99 B5 + * + * ; Example #3 + * ; Example serial output of a M261 request + * echo:i2c-reply: from:99 bytes:5 data:hello + */ + +// @section i2cbus + +//#define EXPERIMENTAL_I2CBUS +#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave + +// @section extras + +/** + * Photo G-code + * Add the M240 G-code to take a photo. + * The photo can be triggered by a digital pin or a physical movement. + */ +//#define PHOTO_GCODE +#if ENABLED(PHOTO_GCODE) + // A position to move to (and raise Z) before taking the photo + //#define PHOTO_POSITION { X_MAX_POS - 5, Y_MAX_POS, 0 } // { xpos, ypos, zraise } (M240 X Y Z) + //#define PHOTO_DELAY_MS 100 // (ms) Duration to pause before moving back (M240 P) + //#define PHOTO_RETRACT_MM 6.5 // (mm) E retract/recover for the photo move (M240 R S) + + // Canon RC-1 or homebrew digital camera trigger + // Data from: http://www.doc-diy.net/photo/rc-1_hacked/ + //#define PHOTOGRAPH_PIN 23 + + // Canon Hack Development Kit + // http://captain-slow.dk/2014/03/09/3d-printing-timelapses/ + //#define CHDK_PIN 4 + + // Optional second move with delay to trigger the camera shutter + //#define PHOTO_SWITCH_POSITION { X_MAX_POS, Y_MAX_POS } // { xpos, ypos } (M240 I J) + + // Duration to hold the switch or keep CHDK_PIN high + //#define PHOTO_SWITCH_MS 50 // (ms) (M240 D) +#endif + +/** + * Spindle & Laser control + * + * Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and + * to set spindle speed, spindle direction, and laser power. + * + * SuperPid is a router/spindle speed controller used in the CNC milling community. + * Marlin can be used to turn the spindle on and off. It can also be used to set + * the spindle speed from 5,000 to 30,000 RPM. + * + * You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V + * hardware PWM pin for the speed control and a pin for the rotation direction. + * + * See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details. + */ +//#define SPINDLE_FEATURE +//#define LASER_FEATURE +#if EITHER(SPINDLE_FEATURE, LASER_FEATURE) + #define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH + #define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power + #define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower + #define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power + #define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop + + #if ENABLED(SPINDLE_FEATURE) + //#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction + #define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction + #define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed + + /** + * The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power + * + * SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT + * where PWM duty cycle varies from 0 to 255 + * + * set the following for your controller (ALL MUST BE SET) + */ + #define SPEED_POWER_SLOPE 118.4 + #define SPEED_POWER_INTERCEPT 0 + #define SPEED_POWER_MIN 5000 + #define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM + #else + #define SPEED_POWER_SLOPE 0.3922 + #define SPEED_POWER_INTERCEPT 0 + #define SPEED_POWER_MIN 10 + #define SPEED_POWER_MAX 100 // 0-100% + #endif +#endif + +/** + * Coolant Control + * + * Add the M7, M8, and M9 commands to turn mist or flood coolant on and off. + * + * Note: COOLANT_MIST_PIN and/or COOLANT_FLOOD_PIN must also be defined. + */ +//#define COOLANT_CONTROL +#if ENABLED(COOLANT_CONTROL) + #define COOLANT_MIST // Enable if mist coolant is present + #define COOLANT_FLOOD // Enable if flood coolant is present + #define COOLANT_MIST_INVERT false // Set "true" if the on/off function is reversed + #define COOLANT_FLOOD_INVERT false // Set "true" if the on/off function is reversed +#endif + +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define FILWIDTH_ERROR_MARGIN 1.0 // (mm) If a measurement differs too much from nominal width ignore it + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + +/** + * CNC Coordinate Systems + * + * Enables G53 and G54-G59.3 commands to select coordinate systems + * and G92.1 to reset the workspace to native machine space. + */ +//#define CNC_COORDINATE_SYSTEMS + +/** + * Auto-report temperatures with M155 S + */ +#define AUTO_REPORT_TEMPERATURES + +/** + * Include capabilities in M115 output + */ +#define EXTENDED_CAPABILITIES_REPORT + +/** + * Disable all Volumetric extrusion options + */ +//#define NO_VOLUMETRICS + +#if DISABLED(NO_VOLUMETRICS) + /** + * Volumetric extrusion default state + * Activate to make volumetric extrusion the default method, + * with DEFAULT_NOMINAL_FILAMENT_DIA as the default diameter. + * + * M200 D0 to disable, M200 Dn to set a new diameter. + */ + //#define VOLUMETRIC_DEFAULT_ON +#endif + +/** + * Enable this option for a leaner build of Marlin that removes all + * workspace offsets, simplifying coordinate transformations, leveling, etc. + * + * - M206 and M428 are disabled. + * - G92 will revert to its behavior from Marlin 1.0. + */ +//#define NO_WORKSPACE_OFFSETS + +/** + * Set the number of proportional font spaces required to fill up a typical character space. + * This can help to better align the output of commands like `G29 O` Mesh Output. + * + * For clients that use a fixed-width font (like OctoPrint), leave this set to 1.0. + * Otherwise, adjust according to your client and font. + */ +#define PROPORTIONAL_FONT_RATIO 1.0 + +/** + * Spend 28 bytes of SRAM to optimize the GCode parser + */ +#define FASTER_GCODE_PARSER + +/** + * CNC G-code options + * Support CNC-style G-code dialects used by laser cutters, drawing machine cams, etc. + * Note that G0 feedrates should be used with care for 3D printing (if used at all). + * High feedrates may cause ringing and harm print quality. + */ +//#define PAREN_COMMENTS // Support for parentheses-delimited comments +//#define GCODE_MOTION_MODES // Remember the motion mode (G0 G1 G2 G3 G5 G38.X) and apply for X Y Z E F, etc. + +// Enable and set a (default) feedrate for all G0 moves +//#define G0_FEEDRATE 3000 // (mm/m) +#ifdef G0_FEEDRATE + //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode +#endif + +/** + * G-code Macros + * + * Add G-codes M810-M819 to define and run G-code macros. + * Macros are not saved to EEPROM. + */ +//#define GCODE_MACROS +#if ENABLED(GCODE_MACROS) + #define GCODE_MACROS_SLOTS 5 // Up to 10 may be used + #define GCODE_MACROS_SLOT_SIZE 50 // Maximum length of a single macro +#endif + +/** + * User-defined menu items that execute custom GCode + */ +//#define CUSTOM_USER_MENUS +#if ENABLED(CUSTOM_USER_MENUS) + //#define CUSTOM_USER_MENU_TITLE "Custom Commands" + #define USER_SCRIPT_DONE "M117 User Script Done" + #define USER_SCRIPT_AUDIBLE_FEEDBACK + //#define USER_SCRIPT_RETURN // Return to status screen after a script + + #define USER_DESC_1 "Home & UBL Info" + #define USER_GCODE_1 "G28\nG29 W" + + #define USER_DESC_2 "Preheat for " PREHEAT_1_LABEL + #define USER_GCODE_2 "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND) + + #define USER_DESC_3 "Preheat for " PREHEAT_2_LABEL + #define USER_GCODE_3 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND) + + #define USER_DESC_4 "Heat Bed/Home/Level" + #define USER_GCODE_4 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29" + + #define USER_DESC_5 "Home & Info" + #define USER_GCODE_5 "G28\nM503" +#endif + +/** + * Host Action Commands + * + * Define host streamer action commands in compliance with the standard. + * + * See https://reprap.org/wiki/G-code#Action_commands + * Common commands ........ poweroff, pause, paused, resume, resumed, cancel + * G29_RETRY_AND_RECOVER .. probe_rewipe, probe_failed + * + * Some features add reason codes to extend these commands. + * + * Host Prompt Support enables Marlin to use the host for user prompts so + * filament runout and other processes can be managed from the host side. + */ +//#define HOST_ACTION_COMMANDS +#if ENABLED(HOST_ACTION_COMMANDS) + //#define HOST_PROMPT_SUPPORT +#endif + +//=========================================================================== +//====================== I2C Position Encoder Settings ====================== +//=========================================================================== + +/** + * I2C position encoders for closed loop control. + * Developed by Chris Barr at Aus3D. + * + * Wiki: http://wiki.aus3d.com.au/Magnetic_Encoder + * Github: https://github.com/Aus3D/MagneticEncoder + * + * Supplier: http://aus3d.com.au/magnetic-encoder-module + * Alternative Supplier: http://reliabuild3d.com/ + * + * Reliabuild encoders have been modified to improve reliability. + */ + +//#define I2C_POSITION_ENCODERS +#if ENABLED(I2C_POSITION_ENCODERS) + + #define I2CPE_ENCODER_CNT 1 // The number of encoders installed; max of 5 + // encoders supported currently. + + #define I2CPE_ENC_1_ADDR I2CPE_PRESET_ADDR_X // I2C address of the encoder. 30-200. + #define I2CPE_ENC_1_AXIS X_AXIS // Axis the encoder module is installed on. _AXIS. + #define I2CPE_ENC_1_TYPE I2CPE_ENC_TYPE_LINEAR // Type of encoder: I2CPE_ENC_TYPE_LINEAR -or- + // I2CPE_ENC_TYPE_ROTARY. + #define I2CPE_ENC_1_TICKS_UNIT 2048 // 1024 for magnetic strips with 2mm poles; 2048 for + // 1mm poles. For linear encoders this is ticks / mm, + // for rotary encoders this is ticks / revolution. + //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper + // steps per full revolution (motor steps/rev * microstepping) + //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the + // printer will attempt to correct the error; errors + // smaller than this are ignored to minimize effects of + // measurement noise / latency (filter). + + #define I2CPE_ENC_2_ADDR I2CPE_PRESET_ADDR_Y // Same as above, but for encoder 2. + #define I2CPE_ENC_2_AXIS Y_AXIS + #define I2CPE_ENC_2_TYPE I2CPE_ENC_TYPE_LINEAR + #define I2CPE_ENC_2_TICKS_UNIT 2048 + //#define I2CPE_ENC_2_TICKS_REV (16 * 200) + //#define I2CPE_ENC_2_INVERT + #define I2CPE_ENC_2_EC_METHOD I2CPE_ECM_MICROSTEP + #define I2CPE_ENC_2_EC_THRESH 0.10 + + #define I2CPE_ENC_3_ADDR I2CPE_PRESET_ADDR_Z // Encoder 3. Add additional configuration options + #define I2CPE_ENC_3_AXIS Z_AXIS // as above, or use defaults below. + + #define I2CPE_ENC_4_ADDR I2CPE_PRESET_ADDR_E // Encoder 4. + #define I2CPE_ENC_4_AXIS E_AXIS + + #define I2CPE_ENC_5_ADDR 34 // Encoder 5. + #define I2CPE_ENC_5_AXIS E_AXIS + + // Default settings for encoders which are enabled, but without settings configured above. + #define I2CPE_DEF_TYPE I2CPE_ENC_TYPE_LINEAR + #define I2CPE_DEF_ENC_TICKS_UNIT 2048 + #define I2CPE_DEF_TICKS_REV (16 * 200) + #define I2CPE_DEF_EC_METHOD I2CPE_ECM_NONE + #define I2CPE_DEF_EC_THRESH 0.1 + + //#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given + // axis after which the printer will abort. Comment out to + // disable abort behavior. + + #define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault + // for this amount of time (in ms) before the encoder + // is trusted again. + + /** + * Position is checked every time a new command is executed from the buffer but during long moves, + * this setting determines the minimum update time between checks. A value of 100 works well with + * error rolling average when attempting to correct only for skips and not for vibration. + */ + #define I2CPE_MIN_UPD_TIME_MS 4 // (ms) Minimum time between encoder checks. + + // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise. + #define I2CPE_ERR_ROLLING_AVERAGE + +#endif // I2C_POSITION_ENCODERS + +/** + * MAX7219 Debug Matrix + * + * Add support for a low-cost 8x8 LED Matrix based on the Max7219 chip as a realtime status display. + * Requires 3 signal wires. Some useful debug options are included to demonstrate its usage. + */ +//#define MAX7219_DEBUG +#if ENABLED(MAX7219_DEBUG) + #define MAX7219_CLK_PIN 64 + #define MAX7219_DIN_PIN 57 + #define MAX7219_LOAD_PIN 44 + + //#define MAX7219_GCODE // Add the M7219 G-code to control the LED matrix + #define MAX7219_INIT_TEST 2 // Do a test pattern at initialization (Set to 2 for spiral) + #define MAX7219_NUMBER_UNITS 1 // Number of Max7219 units in chain. + #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) + // connector at: right=0 bottom=-90 top=90 left=180 + //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side + + /** + * Sample debug features + * If you add more debug displays, be careful to avoid conflicts! + */ + #define MAX7219_DEBUG_PRINTER_ALIVE // Blink corner LED of 8x8 matrix to show that the firmware is functioning + #define MAX7219_DEBUG_PLANNER_HEAD 3 // Show the planner queue head position on this and the next LED matrix row + #define MAX7219_DEBUG_PLANNER_TAIL 5 // Show the planner queue tail position on this and the next LED matrix row + + #define MAX7219_DEBUG_PLANNER_QUEUE 0 // Show the current planner queue depth on this and the next LED matrix row + // If you experience stuttering, reboots, etc. this option can reveal how + // tweaks made to the configuration are affecting the printer in real-time. +#endif + +/** + * NanoDLP Sync support + * + * Add support for Synchronized Z moves when using with NanoDLP. G0/G1 axis moves will output "Z_move_comp" + * string to enable synchronization with DLP projector exposure. This change will allow to use + * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands + */ +//#define NANODLP_Z_SYNC +#if ENABLED(NANODLP_Z_SYNC) + //#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move. + // Default behavior is limited to Z axis only. +#endif + +/** + * WiFi Support (Espressif ESP32 WiFi) + */ +//#define WIFISUPPORT +#if ENABLED(WIFISUPPORT) + #define WIFI_SSID "Wifi SSID" + #define WIFI_PWD "Wifi Password" + //#define WEBSUPPORT // Start a webserver with auto-discovery + //#define OTASUPPORT // Support over-the-air firmware updates +#endif + +/** + * Prusa Multi-Material Unit v2 + * Enable in Configuration.h + */ +#if ENABLED(PRUSA_MMU2) + + // Serial port used for communication with MMU2. + // For AVR enable the UART port used for the MMU. (e.g., internalSerial) + // For 32-bit boards check your HAL for available serial ports. (e.g., Serial2) + #define INTERNAL_SERIAL_PORT 2 + #define MMU2_SERIAL internalSerial + + // Use hardware reset for MMU if a pin is defined for it + //#define MMU2_RST_PIN 23 + + // Enable if the MMU2 has 12V stepper motors (MMU2 Firmware 1.0.2 and up) + //#define MMU2_MODE_12V + + // G-code to execute when MMU2 F.I.N.D.A. probe detects filament runout + #define MMU2_FILAMENT_RUNOUT_SCRIPT "M600" + + // Add an LCD menu for MMU2 + //#define MMU2_MENUS + #if ENABLED(MMU2_MENUS) + // Settings for filament load / unload from the LCD menu. + // This is for Prusa MK3-style extruders. Customize for your hardware. + #define MMU2_FILAMENTCHANGE_EJECT_FEED 80.0 + #define MMU2_LOAD_TO_NOZZLE_SEQUENCE \ + { 7.2, 562 }, \ + { 14.4, 871 }, \ + { 36.0, 1393 }, \ + { 14.4, 871 }, \ + { 50.0, 198 } + + #define MMU2_RAMMING_SEQUENCE \ + { 1.0, 1000 }, \ + { 1.0, 1500 }, \ + { 2.0, 2000 }, \ + { 1.5, 3000 }, \ + { 2.5, 4000 }, \ + { -15.0, 5000 }, \ + { -14.0, 1200 }, \ + { -6.0, 600 }, \ + { 10.0, 700 }, \ + { -10.0, 400 }, \ + { -50.0, 2000 } + + #endif + + //#define MMU2_DEBUG // Write debug info to serial output + +#endif // PRUSA_MMU2 + +/** + * Advanced Print Counter settings + */ +#if ENABLED(PRINTCOUNTER) + #define SERVICE_WARNING_BUZZES 3 + // Activate up to 3 service interval watchdogs + //#define SERVICE_NAME_1 "Service S" + //#define SERVICE_INTERVAL_1 100 // print hours + //#define SERVICE_NAME_2 "Service L" + //#define SERVICE_INTERVAL_2 200 // print hours + //#define SERVICE_NAME_3 "Service 3" + //#define SERVICE_INTERVAL_3 1 // print hours +#endif + +// @section develop + +/** + * M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins + */ +//#define PINS_DEBUGGING + +// Enable Marlin dev mode which adds some special commands +//#define MARLIN_DEV_MODE diff --git a/config/examples/Tevo/Michelangelo/_Bootscreen.h b/config/examples/Tevo/Michelangelo/_Bootscreen.h new file mode 100644 index 0000000000..b3d74daf48 --- /dev/null +++ b/config/examples/Tevo/Michelangelo/_Bootscreen.h @@ -0,0 +1,83 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Made with Marlin Bitmap Converter + * http://marlinfw.org/tools/u8glib/converter.html + */ +#define CUSTOM_BOOTSCREEN_BMPWIDTH 128 + +const unsigned char custom_start_bmp[] PROGMEM = { + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000001,B11111111, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00001111,B11111111, + B00000000,B00000000,B00000000,B00001111,B11111100,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B01111111,B11111111, + B00000000,B00000000,B00000000,B00111111,B11111111,B10000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000001,B11111111,B11111111, + B00000000,B00000000,B00000001,B11111111,B11111111,B11111111,B10000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B01111111,B11111111,B11111111, + B00000000,B00000000,B00000111,B11111111,B11111111,B11111111,B11100000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000111,B11111111,B11111111,B11111111, + B00000000,B00000000,B00011111,B11111111,B11111111,B11111111,B11110000,B00000000,B00000000,B00000000,B00000000,B00000000,B11111111,B11111111,B11111111,B11111111, + B00000000,B00000000,B01111111,B11111111,B11111111,B11111111,B11111100,B00000000,B00000000,B00000000,B00000000,B00000111,B11111111,B11111111,B11111111,B11111111, + B00000000,B00000011,B11111111,B11111111,B11111111,B11111111,B11111111,B00000000,B00000000,B00000000,B00000001,B11111111,B11111111,B11111111,B11111111,B11111111, + B00000000,B00001111,B11111111,B11111111,B11111111,B11111111,B11111111,B11000000,B00000000,B00000000,B00000111,B11111111,B11111111,B11111111,B11111111,B11111111, + B00000000,B01111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11100000,B00000000,B00000000,B00011111,B11111111,B11111111,B11111111,B11111111,B11111111, + B00001111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11110000,B00000000,B00000111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B11111111,B00111111,B11111011,B11111111,B11110000,B00000011,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B11111100,B00011111,B11111101,B11111111,B11111000,B00011111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B11111000,B00001111,B11111110,B11111111,B11111000,B01111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B11110000,B00000011,B11111111,B01101111,B11011100,B01111111,B10111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B11100000,B00000000,B00111111,B11100111,B11001110,B00000000,B00000011,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B11000000,B00000000,B00001111,B11000111,B11000110,B00000000,B00000001,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B11000000,B00000000,B00000011,B11100011,B11100000,B00000000,B00000001,B11111111,B11111111,B11000000,B11111111,B11111111,B11111111, + B11111111,B11111111,B11111111,B10000000,B00000000,B00000001,B11110011,B11100000,B00000000,B00000111,B11111111,B11111111,B10000000,B00000000,B00000000,B00000000, + B11111111,B11111111,B11111110,B00000000,B00000000,B00000000,B01110001,B11100000,B00000000,B00011111,B11111111,B11111110,B00000000,B00000000,B00000000,B00000000, + B11111111,B11111111,B11111100,B00000000,B00000000,B00000000,B00110001,B11100000,B00000000,B00011111,B11111111,B11111100,B00000000,B00000000,B00000000,B00000000, + B11111111,B11111111,B11111000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00011111,B11111111,B11110000,B00000000,B00000000,B00000000,B00000000, + B11111111,B11111111,B11100000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00001110,B11111111,B11000000,B00000000,B00000000,B00000000,B00000000, + B11111111,B11111111,B10000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00001111,B11101110,B00000000,B00000000,B00000000,B00000000,B00000000, + B11111111,B11111111,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00001110,B11101110,B00000000,B00000000,B00000000,B00000000,B00000000, + B11111111,B11111100,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00001101,B11001110,B00000000,B00000000,B00000000,B00000000,B00000000, + B11111111,B11111000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00001111,B11001110,B00000000,B00000000,B00000000,B00000000,B00000000, + B11111111,B11110000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00001101,B11001110,B00000000,B00000000,B00000000,B00000000,B00000000, + B11111111,B11100000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00001101,B10000100,B00000000,B00000000,B00000000,B00000000,B00000000, + B11111111,B10000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000001,B10000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B11111110,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B11111000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B01100000,B11000110,B00000000,B01110000,B00000000,B00001110,B00000000,B00000000,B00000000,B00000000,B00000111,B00000000,B00000000,B00000000, + B00000000,B00000000,B11110001,B11100110,B00000000,B01110000,B00000000,B00001110,B00000000,B00000000,B00000000,B00000000,B00000111,B00000000,B00000000,B00000000, + B00000000,B00000000,B11110001,B11100000,B00000000,B01110000,B00000000,B00001110,B00000000,B00000000,B00000000,B00000000,B00000111,B00000000,B00000000,B00000000, + B00000000,B00000000,B11111011,B11100000,B00000000,B01110000,B00000000,B00001110,B00000000,B00000000,B00000000,B00000000,B00000111,B00000000,B00000000,B00000000, + B00000000,B00000000,B11111111,B11100110,B00011111,B01110111,B00001111,B10001110,B11111100,B01111111,B00011111,B11100111,B11000111,B00011111,B00000000,B00000000, + B00000000,B00000000,B11111111,B11100110,B00111111,B01111111,B10011111,B11001110,B11111110,B01111111,B00111111,B11101111,B11100111,B00111111,B10000000,B00000000, + B00000000,B00000000,B11101110,B11100110,B01111011,B01111111,B10011000,B11001110,B11001110,B01111111,B10111101,B11101100,B01100111,B01111011,B11000000,B00000000, + B00000000,B00000000,B11101110,B11100110,B01110000,B01110011,B10111111,B11101110,B00111110,B01110011,B10110000,B11011111,B11110111,B01110001,B11000000,B00000000, + B00000000,B00000000,B11100100,B11100110,B01100000,B01110011,B10111111,B11101110,B11111110,B01110011,B10110000,B11011111,B11110111,B01110001,B11000000,B00000000, + B00000000,B00000000,B11100100,B11100110,B01100000,B01110011,B10011000,B00001110,B11001110,B01110011,B10110000,B11001100,B00000111,B01110001,B11000000,B00000000, + B00000000,B00000000,B11100000,B11100110,B01110000,B01110011,B10011000,B00001110,B11001110,B01110011,B10111001,B11001100,B00000111,B01110001,B11000000,B00000000, + B00000000,B00000000,B11100000,B11100110,B01111111,B01110011,B10011111,B11001110,B11111110,B01110011,B10111111,B11101111,B11100111,B01111111,B11000000,B00000000, + B00000000,B00000000,B11100000,B11100110,B00111111,B01110011,B10001111,B11001110,B11111110,B01110011,B10011111,B11100111,B11100111,B00111111,B10000000,B00000000, + B00000000,B00000000,B00000000,B00000000,B00001110,B00110001,B10000111,B00001100,B01110110,B01100011,B00111001,B11000011,B10000110,B00001110,B00000000,B00000000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11000000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00011111,B10000000,B00000000,B00000000,B00000000,B00000000 +}; diff --git a/config/examples/Tevo/Tarantula Pro/Configuration.h b/config/examples/Tevo/Tarantula Pro/Configuration.h index 0995a15e69..bf7bc36569 100644 --- a/config/examples/Tevo/Tarantula Pro/Configuration.h +++ b/config/examples/Tevo/Tarantula Pro/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_MKS_GEN_L #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Tarantula Pro" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -519,7 +525,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -744,9 +750,15 @@ #define DEFAULT_RETRACT_ACCELERATION 10000 // E acceleration for retracts #define DEFAULT_TRAVEL_ACCELERATION 1500 // X, Y, Z acceleration for travel (non printing) moves -// -// Use Junction Deviation instead of traditional Jerk Limiting -// +/** + * Junction Deviation + * + * Use Junction Deviation instead of traditional Jerk Limiting + * + * See: + * https://reprap.org/forum/read.php?1,739819 + * http://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html + */ //#define JUNCTION_DEVIATION #if ENABLED(JUNCTION_DEVIATION) #define JUNCTION_DEVIATION_MM 0.02 // (mm) Distance from real junction edge @@ -1515,8 +1527,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1673,6 +1688,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1900,31 +1923,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1958,15 +1962,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1979,6 +1974,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2004,17 +2041,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2110,8 +2154,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Tevo/Tarantula Pro/Configuration_adv.h b/config/examples/Tevo/Tarantula Pro/Configuration_adv.h index 36b433ff4f..5f2472c0a5 100644 --- a/config/examples/Tevo/Tarantula Pro/Configuration_adv.h +++ b/config/examples/Tevo/Tarantula Pro/Configuration_adv.h @@ -646,6 +646,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -847,6 +848,9 @@ // Include a page of printer information in the LCD Main Menu #define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -1033,7 +1037,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1131,6 +1135,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1360,6 +1365,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1745,6 +1753,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2430,6 +2441,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h new file mode 100644 index 0000000000..2a84ac9c46 --- /dev/null +++ b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h @@ -0,0 +1,2215 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Configuration.h + * + * Basic settings such as: + * + * - Type of electronics + * - Type of temperature sensor + * - Printer geometry + * - Endstop configuration + * - LCD controller + * - Extra features + * + * Advanced settings can be found in Configuration_adv.h + * + */ +#define CONFIGURATION_H_VERSION 020000 + +//=========================================================================== +//============================= Getting Started ============================= +//=========================================================================== + +/** + * Here are some standard links for getting your machine calibrated: + * + * http://reprap.org/wiki/Calibration + * http://youtu.be/wAL9d7FgInk + * http://calculator.josefprusa.cz + * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide + * http://www.thingiverse.com/thing:5573 + * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap + * http://www.thingiverse.com/thing:298812 + */ + +//=========================================================================== +//============================= DELTA Printer =============================== +//=========================================================================== +// For a Delta printer start with one of the configuration files in the +// config/examples/delta directory and customize for your machine. +// + +//=========================================================================== +//============================= SCARA Printer =============================== +//=========================================================================== +// For a SCARA printer start with the configuration files in +// config/examples/SCARA and customize for your machine. +// + +// @section info + +// User-specified version info of this build to display in [Pronterface, etc] terminal window during +// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this +// build by the user have been successfully uploaded into firmware. +#define STRING_CONFIG_H_AUTHOR "(thisiskeithb, Tevo Tornado V1)" // Who made the changes. +#define SHOW_BOOTSCREEN +#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1 +#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2 + +/** + * *** VENDORS PLEASE READ *** + * + * Marlin allows you to add a custom boot image for Graphical LCDs. + * With this option Marlin will first show your custom screen followed + * by the standard Marlin logo with version number and web URL. + * + * We encourage you to take advantage of this new feature and we also + * respectfully request that you retain the unmodified Marlin boot screen. + */ + +// Enable to show the bitmap in Marlin/_Bootscreen.h on startup. +#define SHOW_CUSTOM_BOOTSCREEN + +// Enable to show the bitmap in Marlin/_Statusscreen.h on the status screen. +//#define CUSTOM_STATUS_SCREEN_IMAGE + +// @section machine + +/** + * Select the serial port on the board to use for communication with the host. + * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. + * + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] + */ +#define SERIAL_PORT 0 + +/** + * Select a secondary serial port on the board to use for communication with the host. + * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. + * + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] + */ +//#define SERIAL_PORT_2 -1 + +/** + * This setting determines the communication speed of the printer. + * + * 250000 works in most cases, but you might try a lower speed if + * you commonly experience drop-outs during host printing. + * You may try up to 1000000 to speed up SD file transfer. + * + * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000] + */ +#define BAUDRATE 250000 + +// Enable the Bluetooth serial interface on AT90USB devices +//#define BLUETOOTH + +// Choose the name from boards.h that matches your setup +#ifndef MOTHERBOARD + #define MOTHERBOARD BOARD_MKS_BASE_15 +#endif + +// Name displayed in the LCD "Ready" message and Info menu +#define CUSTOM_MACHINE_NAME "Tornado" + +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 +//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" + +// @section extruder + +// This defines the number of extruders +// :[1, 2, 3, 4, 5, 6] +#define EXTRUDERS 1 + +// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc. +#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 + +// For Cyclops or any "multi-extruder" that shares a single nozzle. +//#define SINGLENOZZLE + +/** + * Průša MK2 Single Nozzle Multi-Material Multiplexer, and variants. + * + * This device allows one stepper driver on a control board to drive + * two to eight stepper motors, one at a time, in a manner suitable + * for extruders. + * + * This option only allows the multiplexer to switch on tool-change. + * Additional options to configure custom E moves are pending. + */ +//#define MK2_MULTIPLEXER +#if ENABLED(MK2_MULTIPLEXER) + // Override the default DIO selector pins here, if needed. + // Some pins files may provide defaults for these pins. + //#define E_MUX0_PIN 40 // Always Required + //#define E_MUX1_PIN 42 // Needed for 3 to 8 inputs + //#define E_MUX2_PIN 44 // Needed for 5 to 8 inputs +#endif + +/** + * Prusa Multi-Material Unit v2 + * + * Requires NOZZLE_PARK_FEATURE to park print head in case MMU unit fails. + * Requires EXTRUDERS = 5 + * + * For additional configuration see Configuration_adv.h + */ +//#define PRUSA_MMU2 + +// A dual extruder that uses a single stepper motor +//#define SWITCHING_EXTRUDER +#if ENABLED(SWITCHING_EXTRUDER) + #define SWITCHING_EXTRUDER_SERVO_NR 0 + #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3] + #if EXTRUDERS > 3 + #define SWITCHING_EXTRUDER_E23_SERVO_NR 1 + #endif +#endif + +// A dual-nozzle that uses a servomotor to raise/lower one (or both) of the nozzles +//#define SWITCHING_NOZZLE +#if ENABLED(SWITCHING_NOZZLE) + #define SWITCHING_NOZZLE_SERVO_NR 0 + //#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second + #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo) +#endif + +/** + * Two separate X-carriages with extruders that connect to a moving part + * via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN. + */ +//#define PARKING_EXTRUDER + +/** + * Two separate X-carriages with extruders that connect to a moving part + * via a magnetic docking mechanism using movements and no solenoid + * + * project : https://www.thingiverse.com/thing:3080893 + * movements : https://youtu.be/0xCEiG9VS3k + * https://youtu.be/Bqbcs0CU2FE + */ +//#define MAGNETIC_PARKING_EXTRUDER + +#if EITHER(PARKING_EXTRUDER, MAGNETIC_PARKING_EXTRUDER) + + #define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders + #define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder + //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381 + + #if ENABLED(PARKING_EXTRUDER) + + #define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage + #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil + #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined. + //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381 + + #elif ENABLED(MAGNETIC_PARKING_EXTRUDER) + + #define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point + #define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple + #define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point + #define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling + + #endif + +#endif + +/** + * Switching Toolhead + * + * Support for swappable and dockable toolheads, such as + * the E3D Tool Changer. Toolheads are locked with a servo. + */ +//#define SWITCHING_TOOLHEAD + +/** + * Magnetic Switching Toolhead + * + * Support swappable and dockable toolheads with a magnetic + * docking mechanism using movement and no servo. + */ +//#define MAGNETIC_SWITCHING_TOOLHEAD + +/** + * Electromagnetic Switching Toolhead + * + * Parking for CoreXY / HBot kinematics. + * Toolheads are parked at one edge and held with an electromagnet. + * Supports more than 2 Toolheads. See https://youtu.be/JolbsAKTKf4 + */ +//#define ELECTROMAGNETIC_SWITCHING_TOOLHEAD + +#if ANY(SWITCHING_TOOLHEAD, MAGNETIC_SWITCHING_TOOLHEAD, ELECTROMAGNETIC_SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_Y_POS 235 // (mm) Y position of the toolhead dock + #define SWITCHING_TOOLHEAD_Y_SECURITY 10 // (mm) Security distance Y axis + #define SWITCHING_TOOLHEAD_Y_CLEAR 60 // (mm) Minimum distance from dock for unobstructed X axis + #define SWITCHING_TOOLHEAD_X_POS { 215, 0 } // (mm) X positions for parking the extruders + #if ENABLED(SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_SERVO_NR 2 // Index of the servo connector + #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock + #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif + #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching + #endif +#endif + +/** + * "Mixing Extruder" + * - Adds G-codes M163 and M164 to set and "commit" the current mix factors. + * - Extends the stepping routines to move multiple steppers in proportion to the mix. + * - Optional support for Repetier Firmware's 'M164 S' supporting virtual tools. + * - This implementation supports up to two mixing extruders. + * - Enable DIRECT_MIXING_IN_G1 for M165 and mixing in G1 (from Pia Taubert's reference implementation). + */ +//#define MIXING_EXTRUDER +#if ENABLED(MIXING_EXTRUDER) + #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder + #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164 + //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands + //#define GRADIENT_MIX // Support for gradient mixing with M166 and LCD + #if ENABLED(GRADIENT_MIX) + //#define GRADIENT_VTOOL // Add M166 T to use a V-tool index as a Gradient alias + #endif +#endif + +// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). +// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). +// For the other hotends it is their distance from the extruder 0 hotend. +//#define HOTEND_OFFSET_X { 0.0, 20.00 } // (mm) relative X-offset for each nozzle +//#define HOTEND_OFFSET_Y { 0.0, 5.00 } // (mm) relative Y-offset for each nozzle +//#define HOTEND_OFFSET_Z { 0.0, 0.00 } // (mm) relative Z-offset for each nozzle + +// @section machine + +/** + * Power Supply Control + * + * Enable and connect the power supply to the PS_ON_PIN. + * Specify whether the power supply is active HIGH or active LOW. + */ +//#define PSU_CONTROL +//#define PSU_NAME "Power Supply" + +#if ENABLED(PSU_CONTROL) + #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2) + + //#define PS_DEFAULT_OFF // Keep power off until enabled directly with M80 + + //#define AUTO_POWER_CONTROL // Enable automatic control of the PS_ON pin + #if ENABLED(AUTO_POWER_CONTROL) + #define AUTO_POWER_FANS // Turn on PSU if fans need power + #define AUTO_POWER_E_FANS + #define AUTO_POWER_CONTROLLERFAN + #define AUTO_POWER_CHAMBER_FAN + //#define AUTO_POWER_E_TEMP 50 // (°C) Turn on PSU over this temperature + //#define AUTO_POWER_CHAMBER_TEMP 30 // (°C) Turn on PSU over this temperature + #define POWER_TIMEOUT 30 + #endif +#endif + +// @section temperature + +//=========================================================================== +//============================= Thermal Settings ============================ +//=========================================================================== + +/** + * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table + * + * Temperature sensors available: + * + * -4 : thermocouple with AD8495 + * -3 : thermocouple with MAX31855 (only for sensor 0) + * -2 : thermocouple with MAX6675 (only for sensor 0) + * -1 : thermocouple with AD595 + * 0 : not used + * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 3 : Mendel-parts thermistor (4.7k pullup) + * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! + * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) + * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) + * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) + * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) + * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) + * 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) + * 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) + * 10 : 100k RS thermistor 198-961 (4.7k pullup) + * 11 : 100k beta 3950 1% thermistor (4.7k pullup) + * 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) + * 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" + * 15 : 100k thermistor calibration for JGAurora A5 hotend + * 18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327 + * 20 : the PT100 circuit found in the Ultimainboard V2.x + * 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 + * 61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup + * 66 : 4.7M High Temperature thermistor from Dyze Design + * 67 : 450C thermistor from SliceEngineering + * 70 : the 100K thermistor found in the bq Hephestos 2 + * 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor + * + * 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k. + * (but gives greater accuracy and more stable PID) + * 51 : 100k thermistor - EPCOS (1k pullup) + * 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup) + * 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) + * + * 1047 : Pt1000 with 4k7 pullup + * 1010 : Pt1000 with 1k pullup (non standard) + * 147 : Pt100 with 4k7 pullup + * 110 : Pt100 with 1k pullup (non standard) + * + * 1000 : Custom - Specify parameters in Configuration_adv.h + * + * Use these for Testing or Development purposes. NEVER for production machine. + * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. + * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. + * + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + */ +#define TEMP_SENSOR_0 1 +#define TEMP_SENSOR_1 0 +#define TEMP_SENSOR_2 0 +#define TEMP_SENSOR_3 0 +#define TEMP_SENSOR_4 0 +#define TEMP_SENSOR_5 0 +#define TEMP_SENSOR_BED 1 +#define TEMP_SENSOR_CHAMBER 0 + +// Dummy thermistor constant temperature readings, for use with 998 and 999 +#define DUMMY_THERMISTOR_998_VALUE 25 +#define DUMMY_THERMISTOR_999_VALUE 100 + +// Use temp sensor 1 as a redundant sensor with sensor 0. If the readings +// from the two sensors differ too much the print will be aborted. +//#define TEMP_SENSOR_1_AS_REDUNDANT +#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 + +#define TEMP_RESIDENCY_TIME 5 // (seconds) Time to wait for hotend to "settle" in M109 +#define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer +#define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target + +#define TEMP_BED_RESIDENCY_TIME 5 // (seconds) Time to wait for bed to "settle" in M190 +#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer +#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target + +// Below this temperature the heater will be switched off +// because it probably indicates a broken thermistor wire. +#define HEATER_0_MINTEMP 5 +#define HEATER_1_MINTEMP 5 +#define HEATER_2_MINTEMP 5 +#define HEATER_3_MINTEMP 5 +#define HEATER_4_MINTEMP 5 +#define HEATER_5_MINTEMP 5 +#define BED_MINTEMP 5 + +// Above this temperature the heater will be switched off. +// This can protect components from overheating, but NOT from shorts and failures. +// (Use MINTEMP for thermistor short/failure protection.) +#define HEATER_0_MAXTEMP 285 +#define HEATER_1_MAXTEMP 275 +#define HEATER_2_MAXTEMP 275 +#define HEATER_3_MAXTEMP 275 +#define HEATER_4_MAXTEMP 275 +#define HEATER_5_MAXTEMP 275 +#define BED_MAXTEMP 150 + +//=========================================================================== +//============================= PID Settings ================================ +//=========================================================================== +// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning + +// Comment the following line to disable PID and enable bang-bang. +#define PIDTEMP +#define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current +#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current +#define PID_K1 0.95 // Smoothing factor within any PID loop +#if ENABLED(PIDTEMP) + #define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM) + #define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM) + //#define PID_DEBUG // Sends debug data to the serial port. + //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX + //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay + //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] + #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature + // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. + + // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it + + // Tevo Tornado V1 + #define DEFAULT_Kp 20.37 + #define DEFAULT_Ki 1.50 + #define DEFAULT_Kd 69.26 + + // Ultimaker + //#define DEFAULT_Kp 22.2 + //#define DEFAULT_Ki 1.08 + //#define DEFAULT_Kd 114 + + // MakerGear + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 + + // Mendel Parts V9 on 12V + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 + +#endif // PIDTEMP + +//=========================================================================== +//====================== PID > Bed Temperature Control ====================== +//=========================================================================== + +/** + * PID Bed Heating + * + * If this option is enabled set PID constants below. + * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis. + * + * The PID frequency will be the same as the extruder PWM. + * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz, + * which is fine for driving a square wave into a resistive load and does not significantly + * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W + * heater. If your configuration is significantly different than this and you don't understand + * the issues involved, don't use bed PID until someone else verifies that your hardware works. + */ +#define PIDTEMPBED + +//#define BED_LIMIT_SWITCHING + +/** + * Max Bed Power + * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis). + * When set to any value below 255, enables a form of PWM to the bed that acts like a divider + * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED) + */ +#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current + +#if ENABLED(PIDTEMPBED) + //#define MIN_BED_POWER 0 + //#define PID_BED_DEBUG // Sends debug data to the serial port. + + //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) + //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) + #define DEFAULT_bedKp 128.82 + #define DEFAULT_bedKi 16.91 + #define DEFAULT_bedKd 245.36 + + //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) + //from pidautotune + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 + + // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. +#endif // PIDTEMPBED + +// @section extruder + +/** + * Prevent extrusion if the temperature is below EXTRUDE_MINTEMP. + * Add M302 to set the minimum extrusion temperature and/or turn + * cold extrusion prevention on and off. + * + * *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! *** + */ +#define PREVENT_COLD_EXTRUSION +#define EXTRUDE_MINTEMP 170 + +/** + * Prevent a single extrusion longer than EXTRUDE_MAXLENGTH. + * Note: For Bowden Extruders make this large enough to allow load/unload. + */ +#define PREVENT_LENGTHY_EXTRUDE +#define EXTRUDE_MAXLENGTH 600 + +//=========================================================================== +//======================== Thermal Runaway Protection ======================= +//=========================================================================== + +/** + * Thermal Protection provides additional protection to your printer from damage + * and fire. Marlin always includes safe min and max temperature ranges which + * protect against a broken or disconnected thermistor wire. + * + * The issue: If a thermistor falls out, it will report the much lower + * temperature of the air in the room, and the the firmware will keep + * the heater on. + * + * If you get "Thermal Runaway" or "Heating failed" errors the + * details can be tuned in Configuration_adv.h + */ + +#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders +#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed +#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber + +//=========================================================================== +//============================= Mechanical Settings ========================= +//=========================================================================== + +// @section machine + +// Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics +// either in the usual order or reversed +//#define COREXY +//#define COREXZ +//#define COREYZ +//#define COREYX +//#define COREZX +//#define COREZY + +//=========================================================================== +//============================== Endstop Settings =========================== +//=========================================================================== + +// @section homing + +// Specify here all the endstop connectors that are connected to any endstop or probe. +// Almost all printers will be using one per axis. Probes will use one or more of the +// extra connectors. Leave undefined any used for non-endstop and non-probe purposes. +#define USE_XMIN_PLUG +#define USE_YMIN_PLUG +#define USE_ZMIN_PLUG +//#define USE_XMAX_PLUG +//#define USE_YMAX_PLUG +//#define USE_ZMAX_PLUG + +// Enable pullup for all endstops to prevent a floating state +#define ENDSTOPPULLUPS +#if DISABLED(ENDSTOPPULLUPS) + // Disable ENDSTOPPULLUPS to set pullups individually + //#define ENDSTOPPULLUP_XMAX + //#define ENDSTOPPULLUP_YMAX + //#define ENDSTOPPULLUP_ZMAX + //#define ENDSTOPPULLUP_XMIN + //#define ENDSTOPPULLUP_YMIN + //#define ENDSTOPPULLUP_ZMIN + //#define ENDSTOPPULLUP_ZMIN_PROBE +#endif + +// Enable pulldown for all endstops to prevent a floating state +//#define ENDSTOPPULLDOWNS +#if DISABLED(ENDSTOPPULLDOWNS) + // Disable ENDSTOPPULLDOWNS to set pulldowns individually + //#define ENDSTOPPULLDOWN_XMAX + //#define ENDSTOPPULLDOWN_YMAX + //#define ENDSTOPPULLDOWN_ZMAX + //#define ENDSTOPPULLDOWN_XMIN + //#define ENDSTOPPULLDOWN_YMIN + //#define ENDSTOPPULLDOWN_ZMIN + //#define ENDSTOPPULLDOWN_ZMIN_PROBE +#endif + +// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup). +#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop. +#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop. +#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop. +#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe. + +/** + * Stepper Drivers + * + * These settings allow Marlin to tune stepper driver timing and enable advanced options for + * stepper drivers that support them. You may also override timing options in Configuration_adv.h. + * + * A4988 is assumed for unspecified drivers. + * + * Options: A4988, A5984, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100, + * TMC2130, TMC2130_STANDALONE, TMC2160, TMC2160_STANDALONE, + * TMC2208, TMC2208_STANDALONE, TMC2209, TMC2209_STANDALONE, + * TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE, + * TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE + * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE'] + */ +#define X_DRIVER_TYPE A4988 +#define Y_DRIVER_TYPE A4988 +#define Z_DRIVER_TYPE A4988 +//#define X2_DRIVER_TYPE A4988 +//#define Y2_DRIVER_TYPE A4988 +//#define Z2_DRIVER_TYPE A4988 +//#define Z3_DRIVER_TYPE A4988 +#define E0_DRIVER_TYPE A4988 +//#define E1_DRIVER_TYPE A4988 +//#define E2_DRIVER_TYPE A4988 +//#define E3_DRIVER_TYPE A4988 +//#define E4_DRIVER_TYPE A4988 +//#define E5_DRIVER_TYPE A4988 + +// Enable this feature if all enabled endstop pins are interrupt-capable. +// This will remove the need to poll the interrupt pins, saving many CPU cycles. +//#define ENDSTOP_INTERRUPTS_FEATURE + +/** + * Endstop Noise Threshold + * + * Enable if your probe or endstops falsely trigger due to noise. + * + * - Higher values may affect repeatability or accuracy of some bed probes. + * - To fix noise install a 100nF ceramic capacitor inline with the switch. + * - This feature is not required for common micro-switches mounted on PCBs + * based on the Makerbot design, which already have the 100nF capacitor. + * + * :[2,3,4,5,6,7] + */ +//#define ENDSTOP_NOISE_THRESHOLD 2 + +//============================================================================= +//============================== Movement Settings ============================ +//============================================================================= +// @section motion + +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * With this option each E stepper can have its own factors for the + * following movement settings. If fewer factors are given than the + * total number of extruders, the last value applies to the rest. + */ +//#define DISTINCT_E_FACTORS + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] + */ +#define DEFAULT_AXIS_STEPS_PER_UNIT { 79.765, 79.765, 399.2901, 400 } + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] + */ +#define DEFAULT_MAX_FEEDRATE { 250, 250, 30, 55 } + +/** + * Default Max Acceleration (change/s) change = mm/s + * (Maximum start speed for accelerated moves) + * Override with M201 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] + */ +#define DEFAULT_MAX_ACCELERATION { 2000, 2000, 120, 10000 } + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 1000 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 10000 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 1500 // X, Y, Z acceleration for travel (non printing) moves + +/** + * Junction Deviation + * + * Use Junction Deviation instead of traditional Jerk Limiting + * + * See: + * https://reprap.org/forum/read.php?1,739819 + * http://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html + */ +//#define JUNCTION_DEVIATION +#if ENABLED(JUNCTION_DEVIATION) + #define JUNCTION_DEVIATION_MM 0.02 // (mm) Distance from real junction edge +#endif + +/** + * Default Jerk (mm/s) + * Override with M205 X Y Z E + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#if DISABLED(JUNCTION_DEVIATION) + #define DEFAULT_XJERK 8.0 + #define DEFAULT_YJERK 8.0 + #define DEFAULT_ZJERK 0.4 +#endif + +#define DEFAULT_EJERK 5.0 // May be used by Linear Advance + +/** + * S-Curve Acceleration + * + * This option eliminates vibration during printing by fitting a Bézier + * curve to move acceleration, producing much smoother direction changes. + * + * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained + */ +#define S_CURVE_ACCELERATION + +//=========================================================================== +//============================= Z Probe Options ============================= +//=========================================================================== +// @section probes + +// +// See http://marlinfw.org/docs/configuration/probes.html +// + +/** + * Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + * + * Enable this option for a probe connected to the Z Min endstop pin. + */ +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +/** + * Z_MIN_PROBE_PIN + * + * Define this pin if the probe is not connected to Z_MIN_PIN. + * If not defined the default pin for the selected MOTHERBOARD + * will be used. Most of the time the default is what you want. + * + * - The simplest option is to use a free endstop connector. + * - Use 5V for powered (usually inductive) sensors. + * + * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin: + * - For simple switches connect... + * - normally-closed switches to GND and D32. + * - normally-open switches to 5V and D32. + * + */ +//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default + +/** + * Probe Type + * + * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. + * Activate one of these to use Auto Bed Leveling below. + */ + +/** + * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe. + * Use G29 repeatedly, adjusting the Z height at each point with movement commands + * or (with LCD_BED_LEVELING) the LCD controller. + */ +//#define PROBE_MANUALLY +//#define MANUAL_PROBE_START_Z 0.2 + +/** + * A Fix-Mounted Probe either doesn't deploy or needs manual deployment. + * (e.g., an inductive probe or a nozzle-based probe-switch.) + */ +//#define FIX_MOUNTED_PROBE + +/** + * Z Servo Probe, such as an endstop switch on a rotating arm. + */ +//#define Z_PROBE_SERVO_NR 0 // Defaults to SERVO 0 connector. +//#define Z_SERVO_ANGLES { 70, 0 } // Z Servo Deploy and Stow angles + +/** + * The BLTouch probe uses a Hall effect sensor and emulates a servo. + */ +//#define BLTOUCH + +/** + * Touch-MI Probe by hotends.fr + * + * This probe is deployed and activated by moving the X-axis to a magnet at the edge of the bed. + * By default, the magnet is assumed to be on the left and activated by a home. If the magnet is + * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position. + * + * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING, + * and a minimum Z_HOMING_HEIGHT of 10. + */ +//#define TOUCH_MI_PROBE +#if ENABLED(TOUCH_MI_PROBE) + #define TOUCH_MI_RETRACT_Z 0.5 // Height at which the probe retracts + //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2) // For a magnet on the right side of the bed + //#define TOUCH_MI_MANUAL_DEPLOY // For manual deploy (LCD menu) +#endif + +// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) +//#define SOLENOID_PROBE + +// A sled-mounted probe like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +// A probe deployed by moving the x-axis, such as the Wilson II's rack-and-pinion probe designed by Marty Rice. +//#define RACK_AND_PINION_PROBE +#if ENABLED(RACK_AND_PINION_PROBE) + #define Z_PROBE_DEPLOY_X X_MIN_POS + #define Z_PROBE_RETRACT_X X_MAX_POS +#endif + +// +// For Z_PROBE_ALLEN_KEY see the Delta example configurations. +// + +/** + * Z Probe to nozzle (X,Y) offset, relative to (0, 0). + * X and Y offsets must be integers. + * + * In the following example the X and Y offsets are both positive: + * #define X_PROBE_OFFSET_FROM_EXTRUDER 10 + * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 + * + * +-- BACK ---+ + * | | + * L | (+) P | R <-- probe (20,20) + * E | | I + * F | (-) N (+) | G <-- nozzle (10,10) + * T | | H + * | (-) | T + * | | + * O-- FRONT --+ + * (0,0) + */ +#define X_PROBE_OFFSET_FROM_EXTRUDER -45 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER -12 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER -2.77 // Z offset: -below +above [the nozzle] + +// Certain types of probes need to stay away from edges +#define MIN_PROBE_EDGE 10 + +// X and Y axis travel speed (mm/m) between probes +#define XY_PROBE_SPEED 8000 + +// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2) +#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z + +// Feedrate (mm/m) for the "accurate" probe of each point +#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) + +/** + * Multiple Probing + * + * You may get improved results by probing 2 or more times. + * With EXTRA_PROBING the more atypical reading(s) will be disregarded. + * + * A total of 2 does fast/slow probes with a weighted average. + * A total of 3 or more adds more slow probes, taking the average. + */ +//#define MULTIPLE_PROBING 2 +//#define EXTRA_PROBING 1 + +/** + * Z probes require clearance when deploying, stowing, and moving between + * probe points to avoid hitting the bed and other hardware. + * Servo-mounted probes require extra space for the arm to rotate. + * Inductive probes need space to keep from triggering early. + * + * Use these settings to specify the distance (mm) to raise the probe (or + * lower the bed). The values set here apply over and above any (negative) + * probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD. + * Only integer values >= 1 are valid here. + * + * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle. + * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle. + */ +#define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow +#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points +#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes +//#define Z_AFTER_PROBING 5 // Z position after probing is done + +#define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping + +// For M851 give a range for adjusting the Z probe offset +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + +// Enable the M48 repeatability test to test probe accuracy +//#define Z_MIN_PROBE_REPEATABILITY_TEST + +// Before deploy/stow pause for user confirmation +//#define PAUSE_BEFORE_DEPLOY_STOW +#if ENABLED(PAUSE_BEFORE_DEPLOY_STOW) + //#define PAUSE_PROBE_DEPLOY_WHEN_TRIGGERED // For Manual Deploy Allenkey Probe +#endif + +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + +// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 +// :{ 0:'Low', 1:'High' } +#define X_ENABLE_ON 0 +#define Y_ENABLE_ON 0 +#define Z_ENABLE_ON 0 +#define E_ENABLE_ON 0 // For all extruders + +// Disables axis stepper immediately when it's not being used. +// WARNING: When motors turn off there is a chance of losing position accuracy! +#define DISABLE_X false +#define DISABLE_Y false +#define DISABLE_Z false + +// Warn on display about possibly reduced accuracy +//#define DISABLE_REDUCED_ACCURACY_WARNING + +// @section extruder + +#define DISABLE_E false // For all extruders +#define DISABLE_INACTIVE_EXTRUDER // Keep only the active extruder enabled + +// @section machine + +// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way. +#define INVERT_X_DIR false +#define INVERT_Y_DIR false +#define INVERT_Z_DIR true + +// @section extruder + +// For direct drive extruder v9 set to true, for geared extruder set to false. +#define INVERT_E0_DIR true +#define INVERT_E1_DIR false +#define INVERT_E2_DIR false +#define INVERT_E3_DIR false +#define INVERT_E4_DIR false +#define INVERT_E5_DIR false + +// @section homing + +//#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed + +//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off. + +//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ... + // Be sure you have this distance over your Z_MAX_POS in case. + +// Direction of endstops when homing; 1=MAX, -1=MIN +// :[-1,1] +#define X_HOME_DIR -1 +#define Y_HOME_DIR -1 +#define Z_HOME_DIR -1 + +// @section machine + +// The size of the print bed +#define X_BED_SIZE 320 +#define Y_BED_SIZE 300 + +// Travel limits (mm) after homing, corresponding to endstop positions. +#define X_MIN_POS 0 +#define Y_MIN_POS 0 +#define Z_MIN_POS 0 +#define X_MAX_POS X_BED_SIZE +#define Y_MAX_POS Y_BED_SIZE +#define Z_MAX_POS 400 + +/** + * Software Endstops + * + * - Prevent moves outside the set machine bounds. + * - Individual axes can be disabled, if desired. + * - X and Y only apply to Cartesian robots. + * - Use 'M211' to set software endstops on/off or report current state + */ + +// Min software endstops constrain movement within minimum coordinate bounds +#define MIN_SOFTWARE_ENDSTOPS +#if ENABLED(MIN_SOFTWARE_ENDSTOPS) + #define MIN_SOFTWARE_ENDSTOP_X + #define MIN_SOFTWARE_ENDSTOP_Y + #define MIN_SOFTWARE_ENDSTOP_Z +#endif + +// Max software endstops constrain movement within maximum coordinate bounds +#define MAX_SOFTWARE_ENDSTOPS +#if ENABLED(MAX_SOFTWARE_ENDSTOPS) + #define MAX_SOFTWARE_ENDSTOP_X + #define MAX_SOFTWARE_ENDSTOP_Y + #define MAX_SOFTWARE_ENDSTOP_Z +#endif + +#if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS) + //#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD +#endif + +/** + * Filament Runout Sensors + * Mechanical or opto endstops are used to check for the presence of filament. + * + * RAMPS-based boards use SERVO3_PIN for the first runout sensor. + * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc. + * By default the firmware assumes HIGH=FILAMENT PRESENT. + */ +//#define FILAMENT_RUNOUT_SENSOR +#if ENABLED(FILAMENT_RUNOUT_SENSOR) + #define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each. + #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor. + #define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins. + //#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins. + + // Set one or more commands to execute on filament runout. + // (After 'M412 H' Marlin will ask the host to handle the process.) + #define FILAMENT_RUNOUT_SCRIPT "M600" + + // After a runout is detected, continue printing this length of filament + // before executing the runout script. Useful for a sensor at the end of + // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead. + //#define FILAMENT_RUNOUT_DISTANCE_MM 25 + + #ifdef FILAMENT_RUNOUT_DISTANCE_MM + // Enable this option to use an encoder disc that toggles the runout pin + // as the filament moves. (Be sure to set FILAMENT_RUNOUT_DISTANCE_MM + // large enough to avoid false positives.) + //#define FILAMENT_MOTION_SENSOR + #endif +#endif + +//=========================================================================== +//=============================== Bed Leveling ============================== +//=========================================================================== +// @section calibrate + +/** + * Choose one of the options below to enable G29 Bed Leveling. The parameters + * and behavior of G29 will change depending on your selection. + * + * If using a Probe for Z Homing, enable Z_SAFE_HOMING also! + * + * - AUTO_BED_LEVELING_3POINT + * Probe 3 arbitrary points on the bed (that aren't collinear) + * You specify the XY coordinates of all 3 points. + * The result is a single tilted plane. Best for a flat bed. + * + * - AUTO_BED_LEVELING_LINEAR + * Probe several points in a grid. + * You specify the rectangle and the density of sample points. + * The result is a single tilted plane. Best for a flat bed. + * + * - AUTO_BED_LEVELING_BILINEAR + * Probe several points in a grid. + * You specify the rectangle and the density of sample points. + * The result is a mesh, best for large or uneven beds. + * + * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling) + * A comprehensive bed leveling system combining the features and benefits + * of other systems. UBL also includes integrated Mesh Generation, Mesh + * Validation and Mesh Editing systems. + * + * - MESH_BED_LEVELING + * Probe a grid manually + * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.) + * For machines without a probe, Mesh Bed Leveling provides a method to perform + * leveling in steps so you can manually adjust the Z height at each grid-point. + * With an LCD controller the process is guided step-by-step. + */ +//#define AUTO_BED_LEVELING_3POINT +//#define AUTO_BED_LEVELING_LINEAR +//#define AUTO_BED_LEVELING_BILINEAR +//#define AUTO_BED_LEVELING_UBL +#define MESH_BED_LEVELING + +/** + * Normally G28 leaves leveling disabled on completion. Enable + * this option to have G28 restore the prior leveling state. + */ +#define RESTORE_LEVELING_AFTER_G28 + +/** + * Enable detailed logging of G28, G29, M48, etc. + * Turn on with the command 'M111 S32'. + * NOTE: Requires a lot of PROGMEM! + */ +//#define DEBUG_LEVELING_FEATURE + +#if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_BILINEAR, AUTO_BED_LEVELING_UBL) + // Gradually reduce leveling correction until a set height is reached, + // at which point movement will be level to the machine's XY plane. + // The height can be set with M420 Z + #define ENABLE_LEVELING_FADE_HEIGHT + + // For Cartesian machines, instead of dividing moves on mesh boundaries, + // split up moves into short segments like a Delta. This follows the + // contours of the bed more closely than edge-to-edge straight moves. + #define SEGMENT_LEVELED_MOVES + #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one) + + /** + * Enable the G26 Mesh Validation Pattern tool. + */ + #define G26_MESH_VALIDATION + #if ENABLED(G26_MESH_VALIDATION) + #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle. + #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool. + #define MESH_TEST_HOTEND_TEMP 205 // (°C) Default nozzle temperature for the G26 Mesh Validation Tool. + #define MESH_TEST_BED_TEMP 60 // (°C) Default bed temperature for the G26 Mesh Validation Tool. + #define G26_XY_FEEDRATE 20 // (mm/s) Feedrate for XY Moves for the G26 Mesh Validation Tool. + #endif + +#endif + +#if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR) + + // Set the number of grid points per dimension. + #define GRID_MAX_POINTS_X 3 + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + // Set the boundaries for probing (where the probe can reach). + //#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE + //#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE)) + //#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE + //#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE)) + + // Probe along the Y axis, advancing X after each column + //#define PROBE_Y_FIRST + + #if ENABLED(AUTO_BED_LEVELING_BILINEAR) + + // Beyond the probed grid, continue the implied tilt? + // Default is to maintain the height of the nearest edge. + //#define EXTRAPOLATE_BEYOND_GRID + + // + // Experimental Subdivision of the grid by Catmull-Rom method. + // Synthesizes intermediate points to produce a more detailed mesh. + // + //#define ABL_BILINEAR_SUBDIVISION + #if ENABLED(ABL_BILINEAR_SUBDIVISION) + // Number of subdivisions between probe points + #define BILINEAR_SUBDIVISIONS 3 + #endif + + #endif + +#elif ENABLED(AUTO_BED_LEVELING_UBL) + + //=========================================================================== + //========================= Unified Bed Leveling ============================ + //=========================================================================== + + //#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh + + #define MESH_INSET 1 // Set Mesh bounds as an inset region of the bed + #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited. + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + #define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle + #define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500 + + //#define UBL_Z_RAISE_WHEN_OFF_MESH 2.5 // When the nozzle is off the mesh, this value is used + // as the Z-Height correction value. + +#elif ENABLED(MESH_BED_LEVELING) + + //=========================================================================== + //=================================== Mesh ================================== + //=========================================================================== + + #define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed + #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited. + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS + +#endif // BED_LEVELING + +/** + * Points to probe for all 3-point Leveling procedures. + * Override if the automatically selected points are inadequate. + */ +#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL) + //#define PROBE_PT_1_X 15 + //#define PROBE_PT_1_Y 180 + //#define PROBE_PT_2_X 15 + //#define PROBE_PT_2_Y 20 + //#define PROBE_PT_3_X 170 + //#define PROBE_PT_3_Y 20 +#endif + +/** + * Add a bed leveling sub-menu for ABL or MBL. + * Include a guided procedure if manual probing is enabled. + */ +#define LCD_BED_LEVELING + +#if ENABLED(LCD_BED_LEVELING) + #define MESH_EDIT_Z_STEP 0.025 // (mm) Step size while manually probing Z axis. + #define LCD_PROBE_Z_RANGE 4 // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment + //#define MESH_EDIT_MENU // Add a menu to edit mesh points +#endif + +// Add a menu item to move between bed corners for manual bed adjustment +#define LEVEL_BED_CORNERS + +#if ENABLED(LEVEL_BED_CORNERS) + #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner +#endif + +/** + * Commands to execute at the end of G29 probing. + * Useful to retract or move the Z probe out of the way. + */ +//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" + + +// @section homing + +// The center of the bed is at (X=0, Y=0) +//#define BED_CENTER_AT_0_0 + +// Manually set the home position. Leave these undefined for automatic settings. +// For DELTA this is the top-center of the Cartesian print volume. +//#define MANUAL_X_HOME_POS 0 +//#define MANUAL_Y_HOME_POS 0 +//#define MANUAL_Z_HOME_POS 0 + +// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area. +// +// With this feature enabled: +// +// - Allow Z homing only after X and Y homing AND stepper drivers still enabled. +// - If stepper drivers time out, it will need X and Y homing again before Z homing. +// - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28). +// - Prevent Z homing when the Z probe is outside bed area. +// +//#define Z_SAFE_HOMING + +#if ENABLED(Z_SAFE_HOMING) + #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing when homing all axes (G28). + #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2) // Y point for Z homing when homing all axes (G28). +#endif + +// Homing speeds (mm/m) +#define HOMING_FEEDRATE_XY (50*60) +#define HOMING_FEEDRATE_Z (4*60) + +// Validate that endstops are triggered on homing moves +#define VALIDATE_HOMING_ENDSTOPS + +// @section calibrate + +/** + * Bed Skew Compensation + * + * This feature corrects for misalignment in the XYZ axes. + * + * Take the following steps to get the bed skew in the XY plane: + * 1. Print a test square (e.g., https://www.thingiverse.com/thing:2563185) + * 2. For XY_DIAG_AC measure the diagonal A to C + * 3. For XY_DIAG_BD measure the diagonal B to D + * 4. For XY_SIDE_AD measure the edge A to D + * + * Marlin automatically computes skew factors from these measurements. + * Skew factors may also be computed and set manually: + * + * - Compute AB : SQRT(2*AC*AC+2*BD*BD-4*AD*AD)/2 + * - XY_SKEW_FACTOR : TAN(PI/2-ACOS((AC*AC-AB*AB-AD*AD)/(2*AB*AD))) + * + * If desired, follow the same procedure for XZ and YZ. + * Use these diagrams for reference: + * + * Y Z Z + * ^ B-------C ^ B-------C ^ B-------C + * | / / | / / | / / + * | / / | / / | / / + * | A-------D | A-------D | A-------D + * +-------------->X +-------------->X +-------------->Y + * XY_SKEW_FACTOR XZ_SKEW_FACTOR YZ_SKEW_FACTOR + */ +//#define SKEW_CORRECTION + +#if ENABLED(SKEW_CORRECTION) + // Input all length measurements here: + #define XY_DIAG_AC 282.8427124746 + #define XY_DIAG_BD 282.8427124746 + #define XY_SIDE_AD 200 + + // Or, set the default skew factors directly here + // to override the above measurements: + #define XY_SKEW_FACTOR 0.0 + + //#define SKEW_CORRECTION_FOR_Z + #if ENABLED(SKEW_CORRECTION_FOR_Z) + #define XZ_DIAG_AC 282.8427124746 + #define XZ_DIAG_BD 282.8427124746 + #define YZ_DIAG_AC 282.8427124746 + #define YZ_DIAG_BD 282.8427124746 + #define YZ_SIDE_AD 200 + #define XZ_SKEW_FACTOR 0.0 + #define YZ_SKEW_FACTOR 0.0 + #endif + + // Enable this option for M852 to set skew at runtime + //#define SKEW_CORRECTION_GCODE +#endif + +//============================================================================= +//============================= Additional Features =========================== +//============================================================================= + +// @section extras + +/** + * EEPROM + * + * Persistent storage to preserve configurable settings across reboots. + * + * M500 - Store settings to EEPROM. + * M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes) + * M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.) + */ +#define EEPROM_SETTINGS // Persistent storage with M500 and M501 +//#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release! +#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM. +#if ENABLED(EEPROM_SETTINGS) + #define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors. +#endif + +// +// Host Keepalive +// +// When enabled Marlin will send a busy status message to the host +// every couple of seconds when it can't accept commands. +// +#define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages +#define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113. +#define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating + +// +// M100 Free Memory Watcher +// +//#define M100_FREE_MEMORY_WATCHER // Add M100 (Free Memory Watcher) to debug memory usage + +// +// G20/G21 Inch mode support +// +//#define INCH_MODE_SUPPORT + +// +// M149 Set temperature units support +// +//#define TEMPERATURE_UNITS_SUPPORT + +// @section temperature + +// Preheat Constants +#define PREHEAT_1_LABEL "PLA" +#define PREHEAT_1_TEMP_HOTEND 200 +#define PREHEAT_1_TEMP_BED 70 +#define PREHEAT_1_FAN_SPEED 255 // Value from 0 to 255 + +#define PREHEAT_2_LABEL "ABS" +#define PREHEAT_2_TEMP_HOTEND 240 +#define PREHEAT_2_TEMP_BED 110 +#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255 + +/** + * Nozzle Park + * + * Park the nozzle at the given XYZ position on idle or G27. + * + * The "P" parameter controls the action applied to the Z axis: + * + * P0 (Default) If Z is below park Z raise the nozzle. + * P1 Raise the nozzle always to Z-park height. + * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS. + */ +#define NOZZLE_PARK_FEATURE + +#if ENABLED(NOZZLE_PARK_FEATURE) + // Specify a park position as { X, Y, Z_raise } + #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 } + #define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis) + #define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers) +#endif + +/** + * Clean Nozzle Feature -- EXPERIMENTAL + * + * Adds the G12 command to perform a nozzle cleaning process. + * + * Parameters: + * P Pattern + * S Strokes / Repetitions + * T Triangles (P1 only) + * + * Patterns: + * P0 Straight line (default). This process requires a sponge type material + * at a fixed bed location. "S" specifies strokes (i.e. back-forth motions) + * between the start / end points. + * + * P1 Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the + * number of zig-zag triangles to do. "S" defines the number of strokes. + * Zig-zags are done in whichever is the narrower dimension. + * For example, "G12 P1 S1 T3" will execute: + * + * -- + * | (X0, Y1) | /\ /\ /\ | (X1, Y1) + * | | / \ / \ / \ | + * A | | / \ / \ / \ | + * | | / \ / \ / \ | + * | (X0, Y0) | / \/ \/ \ | (X1, Y0) + * -- +--------------------------------+ + * |________|_________|_________| + * T1 T2 T3 + * + * P2 Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE. + * "R" specifies the radius. "S" specifies the stroke count. + * Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT. + * + * Caveats: The ending Z should be the same as starting Z. + * Attention: EXPERIMENTAL. G-code arguments may change. + * + */ +#define NOZZLE_CLEAN_FEATURE + +#if ENABLED(NOZZLE_CLEAN_FEATURE) + // Default number of pattern repetitions + #define NOZZLE_CLEAN_STROKES 12 + + // Default number of triangles + #define NOZZLE_CLEAN_TRIANGLES 3 + + // Specify positions as { X, Y, Z } + #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)} + #define NOZZLE_CLEAN_END_POINT { 100, 60, (Z_MIN_POS + 1) } + + // Circular pattern radius + #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5 + // Circular pattern circle fragments number + #define NOZZLE_CLEAN_CIRCLE_FN 10 + // Middle point of circle + #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT + + // Move the nozzle to the initial position after cleaning + #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z +#endif + +/** + * Print Job Timer + * + * Automatically start and stop the print job timer on M104/M109/M190. + * + * M104 (hotend, no wait) - high temp = none, low temp = stop timer + * M109 (hotend, wait) - high temp = start timer, low temp = stop timer + * M190 (bed, wait) - high temp = start timer, low temp = none + * + * The timer can also be controlled with the following commands: + * + * M75 - Start the print job timer + * M76 - Pause the print job timer + * M77 - Stop the print job timer + */ +#define PRINTJOB_TIMER_AUTOSTART + +/** + * Print Counter + * + * Track statistical data such as: + * + * - Total print jobs + * - Total successful print jobs + * - Total failed print jobs + * - Total time printing + * + * View the current statistics with M78. + */ +#define PRINTCOUNTER + +//============================================================================= +//============================= LCD and SD support ============================ +//============================================================================= + +// @section lcd + +/** + * LCD LANGUAGE + * + * Select the language to display on the LCD. These languages are available: + * + * en, an, bg, ca, cz, da, de, el, el-gr, es, eu, fi, fr, gl, hr, it, + * jp-kana, ko_KR, nl, pl, pt, pt-br, ru, sk, tr, uk, zh_CN, zh_TW, test + * + * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cz':'Czech', 'da':'Danish', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'jp-kana':'Japanese', 'ko_KR':'Korean (South Korea)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'ru':'Russian', 'sk':'Slovak', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Traditional)', 'test':'TEST' } + */ +#define LCD_LANGUAGE en + +/** + * LCD Character Set + * + * Note: This option is NOT applicable to Graphical Displays. + * + * All character-based LCDs provide ASCII plus one of these + * language extensions: + * + * - JAPANESE ... the most common + * - WESTERN ... with more accented characters + * - CYRILLIC ... for the Russian language + * + * To determine the language extension installed on your controller: + * + * - Compile and upload with LCD_LANGUAGE set to 'test' + * - Click the controller to view the LCD menu + * - The LCD will display Japanese, Western, or Cyrillic text + * + * See http://marlinfw.org/docs/development/lcd_language.html + * + * :['JAPANESE', 'WESTERN', 'CYRILLIC'] + */ +#define DISPLAY_CHARSET_HD44780 WESTERN + +/** + * Info Screen Style (0:Classic, 1:Prusa) + * + * :[0:'Classic', 1:'Prusa'] + */ +#define LCD_INFO_SCREEN_STYLE 0 + +/** + * SD CARD + * + * SD Card support is disabled by default. If your controller has an SD slot, + * you must uncomment the following option or it won't work. + * + */ +#define SDSUPPORT + +/** + * SD CARD: SPI SPEED + * + * Enable one of the following items for a slower SPI transfer speed. + * This may be required to resolve "volume init" errors. + */ +//#define SPI_SPEED SPI_HALF_SPEED +//#define SPI_SPEED SPI_QUARTER_SPEED +//#define SPI_SPEED SPI_EIGHTH_SPEED + +/** + * SD CARD: ENABLE CRC + * + * Use CRC checks and retries on the SD communication. + */ +//#define SD_CHECK_AND_RETRY + +/** + * LCD Menu Items + * + * Disable all menus and only display the Status Screen, or + * just remove some extraneous menu items to recover space. + */ +//#define NO_LCD_MENUS +//#define SLIM_LCD_MENUS + +// +// ENCODER SETTINGS +// +// This option overrides the default number of encoder pulses needed to +// produce one step. Should be increased for high-resolution encoders. +// +#define ENCODER_PULSES_PER_STEP 4 + +// +// Use this option to override the number of step signals required to +// move between next/prev menu items. +// +#define ENCODER_STEPS_PER_MENU_ITEM 1 + +/** + * Encoder Direction Options + * + * Test your encoder's behavior first with both options disabled. + * + * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION. + * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION. + * Reversed Value Editing only? Enable BOTH options. + */ + +// +// This option reverses the encoder direction everywhere. +// +// Set this option if CLOCKWISE causes values to DECREASE +// +#define REVERSE_ENCODER_DIRECTION + +// +// This option reverses the encoder direction for navigating LCD menus. +// +// If CLOCKWISE normally moves DOWN this makes it go UP. +// If CLOCKWISE normally moves UP this makes it go DOWN. +// +//#define REVERSE_MENU_DIRECTION + +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + +// +// Individual Axis Homing +// +// Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu. +// +#define INDIVIDUAL_AXIS_HOMING_MENU + +// +// SPEAKER/BUZZER +// +// If you have a speaker that can produce tones, enable it here. +// By default Marlin assumes you have a buzzer with a fixed frequency. +// +#define SPEAKER + +// +// The duration and frequency for the UI feedback sound. +// Set these to 0 to disable audio feedback in the LCD menus. +// +// Note: Test audio output with the G-Code: +// M300 S P +// +#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 2 +#define LCD_FEEDBACK_FREQUENCY_HZ 5000 + +//============================================================================= +//======================== LCD / Controller Selection ========================= +//======================== (Character-based LCDs) ========================= +//============================================================================= + +// +// RepRapDiscount Smart Controller. +// http://reprap.org/wiki/RepRapDiscount_Smart_Controller +// +// Note: Usually sold with a white PCB. +// +//#define REPRAP_DISCOUNT_SMART_CONTROLLER + +// +// Original RADDS LCD Display+Encoder+SDCardReader +// http://doku.radds.org/dokumentation/lcd-display/ +// +//#define RADDS_DISPLAY + +// +// ULTIMAKER Controller. +// +//#define ULTIMAKERCONTROLLER + +// +// ULTIPANEL as seen on Thingiverse. +// +//#define ULTIPANEL + +// +// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3) +// http://reprap.org/wiki/PanelOne +// +//#define PANEL_ONE + +// +// GADGETS3D G3D LCD/SD Controller +// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel +// +// Note: Usually sold with a blue PCB. +// +//#define G3D_PANEL + +// +// RigidBot Panel V1.0 +// http://www.inventapart.com/ +// +//#define RIGIDBOT_PANEL + +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// ANET and Tronxy 20x4 Controller +// +//#define ZONESTAR_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin. + // This LCD is known to be susceptible to electrical interference + // which scrambles the display. Pressing any button clears it up. + // This is a LCD2004 display with 5 analog buttons. + +// +// Generic 16x2, 16x4, 20x2, or 20x4 character-based LCD. +// +//#define ULTRA_LCD + +//============================================================================= +//======================== LCD / Controller Selection ========================= +//===================== (I2C and Shift-Register LCDs) ===================== +//============================================================================= + +// +// CONTROLLER TYPE: I2C +// +// Note: These controllers require the installation of Arduino's LiquidCrystal_I2C +// library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C +// + +// +// Elefu RA Board Control Panel +// http://www.elefu.com/index.php?route=product/product&product_id=53 +// +//#define RA_CONTROL_PANEL + +// +// Sainsmart (YwRobot) LCD Displays +// +// These require F.Malpartida's LiquidCrystal_I2C library +// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home +// +//#define LCD_SAINSMART_I2C_1602 +//#define LCD_SAINSMART_I2C_2004 + +// +// Generic LCM1602 LCD adapter +// +//#define LCM1602 + +// +// PANELOLU2 LCD with status LEDs, +// separate encoder and click inputs. +// +// Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later. +// For more info: https://github.com/lincomatic/LiquidTWI2 +// +// Note: The PANELOLU2 encoder click input can either be directly connected to +// a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1). +// +//#define LCD_I2C_PANELOLU2 + +// +// Panucatt VIKI LCD with status LEDs, +// integrated click & L/R/U/D buttons, separate encoder inputs. +// +//#define LCD_I2C_VIKI + +// +// CONTROLLER TYPE: Shift register panels +// + +// +// 2-wire Non-latching LCD SR from https://goo.gl/aJJ4sH +// LCD configuration: http://reprap.org/wiki/SAV_3D_LCD +// +//#define SAV_3DLCD + +// +// 3-wire SR LCD with strobe using 74HC4094 +// https://github.com/mikeshub/SailfishLCD +// Uses the code directly from Sailfish +// +//#define FF_INTERFACEBOARD + +//============================================================================= +//======================= LCD / Controller Selection ======================= +//========================= (Graphical LCDs) ======================== +//============================================================================= + +// +// CONTROLLER TYPE: Graphical 128x64 (DOGM) +// +// IMPORTANT: The U8glib library is required for Graphical Display! +// https://github.com/olikraus/U8glib_Arduino +// + +// +// RepRapDiscount FULL GRAPHIC Smart Controller +// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller +// +#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER + +// +// ReprapWorld Graphical LCD +// https://reprapworld.com/?products_details&products_id/1218 +// +//#define REPRAPWORLD_GRAPHICAL_LCD + +// +// Activate one of these if you have a Panucatt Devices +// Viki 2.0 or mini Viki with Graphic LCD +// http://panucatt.com +// +//#define VIKI2 +//#define miniVIKI + +// +// MakerLab Mini Panel with graphic +// controller and SD support - http://reprap.org/wiki/Mini_panel +// +//#define MINIPANEL + +// +// MaKr3d Makr-Panel with graphic controller and SD support. +// http://reprap.org/wiki/MaKr3d_MaKrPanel +// +//#define MAKRPANEL + +// +// Adafruit ST7565 Full Graphic Controller. +// https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/ +// +//#define ELB_FULL_GRAPHIC_CONTROLLER + +// +// BQ LCD Smart Controller shipped by +// default with the BQ Hephestos 2 and Witbox 2. +// +//#define BQ_LCD_SMART_CONTROLLER + +// +// Cartesio UI +// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// +//#define CARTESIO_UI + +// +// LCD for Melzi Card with Graphical LCD +// +//#define LCD_FOR_MELZI + +// +// Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder +// https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) +// +//#define ULTI_CONTROLLER + +// +// MKS MINI12864 with graphic controller and SD support +// https://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// FYSETC variant of the MINI12864 graphic controller with SD support +// https://wiki.fysetc.com/Mini12864_Panel/ +// +//#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default +//#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) +//#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// ANET and Tronxy Graphical Controller +// +// Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6 +// A clone of the RepRapDiscount full graphics display but with +// different pins/wiring (see pins_ANET_10.h). +// +//#define ANET_FULL_GRAPHICS_LCD + +// +// AZSMZ 12864 LCD with SD +// https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html +// +//#define AZSMZ_12864 + +// +// Silvergate GLCD controller +// http://github.com/android444/Silvergate +// +//#define SILVER_GATE_GLCD_CONTROLLER + +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + +//============================================================================= +//========================== Extensible UI Displays =========================== +//============================================================================= + +// +// DGUS Touch Display with DWIN OS +// +//#define DGUS_LCD + +// +// Touch-screen LCD for Malyan M200 printers +// +//#define MALYAN_LCD + +// +// Third-party or vendor-customized controller interfaces. +// Sources should be installed in 'src/lcd/extensible_ui'. +// +//#define EXTENSIBLE_UI + +//============================================================================= +//=============================== Graphical TFTs ============================== +//============================================================================= + +// +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) +// +//#define FSMC_GRAPHICAL_TFT + +//============================================================================= +//============================ Other Controllers ============================ +//============================================================================= + +// +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 +// +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif + +// +// RepRapWorld REPRAPWORLD_KEYPAD v1.1 +// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626 +// +// REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key +// is pressed, a value of 10.0 means 10mm per click. +// +//#define REPRAPWORLD_KEYPAD +//#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 + +//============================================================================= +//=============================== Extra Features ============================== +//============================================================================= + +// @section extras + +// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino +//#define FAST_PWM_FAN + +// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency +// which is not as annoying as with the hardware PWM. On the other hand, if this frequency +// is too low, you should also increment SOFT_PWM_SCALE. +//#define FAN_SOFT_PWM + +// Incrementing this by 1 will double the software PWM frequency, +// affecting heaters, and the fan if FAN_SOFT_PWM is enabled. +// However, control resolution will be halved for each increment; +// at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] +#define SOFT_PWM_SCALE 0 + +// If SOFT_PWM_SCALE is set to a value higher than 0, dithering can +// be used to mitigate the associated resolution loss. If enabled, +// some of the PWM cycles are stretched so on average the desired +// duty cycle is attained. +//#define SOFT_PWM_DITHER + +// Temperature status LEDs that display the hotend and bed temperature. +// If all hotends, bed temperature, and target temperature are under 54C +// then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis) +//#define TEMP_STAT_LEDS + +// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure +//#define SF_ARC_FIX + +// Support for the BariCUDA Paste Extruder +//#define BARICUDA + +// Support for BlinkM/CyzRgb +//#define BLINKM + +// Support for PCA9632 PWM LED driver +//#define PCA9632 + +// Support for PCA9533 PWM LED driver +// https://github.com/mikeshub/SailfishRGB_LED +//#define PCA9533 + +/** + * RGB LED / LED Strip Control + * + * Enable support for an RGB LED connected to 5V digital pins, or + * an RGB Strip connected to MOSFETs controlled by digital pins. + * + * Adds the M150 command to set the LED (or LED strip) color. + * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of + * luminance values can be set from 0 to 255. + * For Neopixel LED an overall brightness parameter is also available. + * + * *** CAUTION *** + * LED Strips require a MOSFET Chip between PWM lines and LEDs, + * as the Arduino cannot handle the current the LEDs will require. + * Failure to follow this precaution can destroy your Arduino! + * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * more current than the Arduino 5V linear regulator can produce. + * *** CAUTION *** + * + * LED Type. Enable only one of the following two options. + * + */ +//#define RGB_LED +//#define RGBW_LED + +#if EITHER(RGB_LED, RGBW_LED) + //#define RGB_LED_R_PIN 34 + //#define RGB_LED_G_PIN 43 + //#define RGB_LED_B_PIN 35 + //#define RGB_LED_W_PIN -1 +#endif + +// Support for Adafruit Neopixel LED driver +//#define NEOPIXEL_LED +#if ENABLED(NEOPIXEL_LED) + #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. + #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) + //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup + + // Use a single Neopixel LED for static (background) lighting + //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use + //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W +#endif + +/** + * Printer Event LEDs + * + * During printing, the LEDs will reflect the printer status: + * + * - Gradually change from blue to violet as the heated bed gets to target temp + * - Gradually change from violet to red as the hotend gets to temperature + * - Change to white to illuminate work surface + * - Change to green once print has finished + * - Turn off after the print has finished and the user has pushed a button + */ +#if ANY(BLINKM, RGB_LED, RGBW_LED, PCA9632, PCA9533, NEOPIXEL_LED) + #define PRINTER_EVENT_LEDS +#endif + +/** + * R/C SERVO support + * Sponsored by TrinityLabs, Reworked by codexmas + */ + +/** + * Number of servos + * + * For some servo-related options NUM_SERVOS will be set automatically. + * Set this manually if there are extra servos needing manual control. + * Leave undefined or set to 0 to entirely disable the servo subsystem. + */ +//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command + +// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. +// 300ms is a good value but you can try less delay. +// If the servo can't reach the requested position, increase it. +#define SERVO_DELAY { 300 } + +// Only power servos during movement, otherwise leave off to prevent jitter +//#define DEACTIVATE_SERVOS_AFTER_MOVE + +// Allow servo angle to be edited and saved to EEPROM +//#define EDITABLE_SERVO_ANGLES diff --git a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h new file mode 100644 index 0000000000..a5f9db1b2f --- /dev/null +++ b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h @@ -0,0 +1,2561 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Configuration_adv.h + * + * Advanced settings. + * Only change these if you know exactly what you're doing. + * Some of these settings can damage your printer if improperly set! + * + * Basic settings can be found in Configuration.h + * + */ +#define CONFIGURATION_ADV_H_VERSION 020000 + +// @section temperature + +//=========================================================================== +//=============================Thermal Settings ============================ +//=========================================================================== + +// +// Custom Thermistor 1000 parameters +// +#if TEMP_SENSOR_0 == 1000 + #define HOTEND0_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND0_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND0_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_1 == 1000 + #define HOTEND1_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND1_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND1_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_2 == 1000 + #define HOTEND2_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND2_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND2_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_3 == 1000 + #define HOTEND3_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND3_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND3_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_4 == 1000 + #define HOTEND4_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND4_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND4_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_5 == 1000 + #define HOTEND5_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND5_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND5_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_BED == 1000 + #define BED_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define BED_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define BED_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_CHAMBER == 1000 + #define CHAMBER_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define CHAMBER_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define CHAMBER_BETA 3950 // Beta value +#endif + +// +// Hephestos 2 24V heated bed upgrade kit. +// https://store.bq.com/en/heated-bed-kit-hephestos2 +// +//#define HEPHESTOS2_HEATED_BED_KIT +#if ENABLED(HEPHESTOS2_HEATED_BED_KIT) + #undef TEMP_SENSOR_BED + #define TEMP_SENSOR_BED 70 + #define HEATER_BED_INVERTING true +#endif + +/** + * Heated Chamber settings + */ +#if TEMP_SENSOR_CHAMBER + #define CHAMBER_MINTEMP 5 + #define CHAMBER_MAXTEMP 60 + #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target + //#define CHAMBER_LIMIT_SWITCHING + //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin + //#define HEATER_CHAMBER_INVERTING false +#endif + +#if DISABLED(PIDTEMPBED) + #define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control + #if ENABLED(BED_LIMIT_SWITCHING) + #define BED_HYSTERESIS 2 // Only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS + #endif +#endif + +/** + * Thermal Protection provides additional protection to your printer from damage + * and fire. Marlin always includes safe min and max temperature ranges which + * protect against a broken or disconnected thermistor wire. + * + * The issue: If a thermistor falls out, it will report the much lower + * temperature of the air in the room, and the the firmware will keep + * the heater on. + * + * The solution: Once the temperature reaches the target, start observing. + * If the temperature stays too far below the target (hysteresis) for too + * long (period), the firmware will halt the machine as a safety precaution. + * + * If you get false positives for "Thermal Runaway", increase + * THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD + */ +#if ENABLED(THERMAL_PROTECTION_HOTENDS) + #define THERMAL_PROTECTION_PERIOD 40 // Seconds + #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius + + //#define ADAPTIVE_FAN_SLOWING // Slow part cooling fan if temperature drops + #if BOTH(ADAPTIVE_FAN_SLOWING, PIDTEMP) + //#define NO_FAN_SLOWING_IN_PID_TUNING // Don't slow fan speed during M303 + #endif + + /** + * Whenever an M104, M109, or M303 increases the target temperature, the + * firmware will wait for the WATCH_TEMP_PERIOD to expire. If the temperature + * hasn't increased by WATCH_TEMP_INCREASE degrees, the machine is halted and + * requires a hard reset. This test restarts with any M104/M109/M303, but only + * if the current temperature is far enough below the target for a reliable + * test. + * + * If you get false positives for "Heating failed", increase WATCH_TEMP_PERIOD + * and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set + * below 2. + */ + #define WATCH_TEMP_PERIOD 20 // Seconds + #define WATCH_TEMP_INCREASE 2 // Degrees Celsius +#endif + +/** + * Thermal Protection parameters for the bed are just as above for hotends. + */ +#if ENABLED(THERMAL_PROTECTION_BED) + #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds + #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius + + /** + * As described above, except for the bed (M140/M190/M303). + */ + #define WATCH_BED_TEMP_PERIOD 60 // Seconds + #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius +#endif + +/** + * Thermal Protection parameters for the heated chamber. + */ +#if ENABLED(THERMAL_PROTECTION_CHAMBER) + #define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds + #define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius + + /** + * Heated chamber watch settings (M141/M191). + */ + #define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds + #define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius +#endif + +#if ENABLED(PIDTEMP) + // Add an experimental additional term to the heater power, proportional to the extrusion speed. + // A well-chosen Kc value should add just enough power to melt the increased material volume. + //#define PID_EXTRUSION_SCALING + #if ENABLED(PID_EXTRUSION_SCALING) + #define DEFAULT_Kc (100) //heating power=Kc*(e_speed) + #define LPQ_MAX_LEN 50 + #endif +#endif + +/** + * Automatic Temperature: + * The hotend target temperature is calculated by all the buffered lines of gcode. + * The maximum buffered steps/sec of the extruder motor is called "se". + * Start autotemp mode with M109 S B F + * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by + * mintemp and maxtemp. Turn this off by executing M109 without F* + * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp. + * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode + */ +#define AUTOTEMP +#if ENABLED(AUTOTEMP) + #define AUTOTEMP_OLDWEIGHT 0.98 +#endif + +// Show extra position information in M114 +//#define M114_DETAIL + +// Show Temperature ADC value +// Enable for M105 to include ADC values read from temperature sensors. +//#define SHOW_TEMP_ADC_VALUES + +/** + * High Temperature Thermistor Support + * + * Thermistors able to support high temperature tend to have a hard time getting + * good readings at room and lower temperatures. This means HEATER_X_RAW_LO_TEMP + * will probably be caught when the heating element first turns on during the + * preheating process, which will trigger a min_temp_error as a safety measure + * and force stop everything. + * To circumvent this limitation, we allow for a preheat time (during which, + * min_temp_error won't be triggered) and add a min_temp buffer to handle + * aberrant readings. + * + * If you want to enable this feature for your hotend thermistor(s) + * uncomment and set values > 0 in the constants below + */ + +// The number of consecutive low temperature errors that can occur +// before a min_temp_error is triggered. (Shouldn't be more than 10.) +//#define MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED 0 + +// The number of milliseconds a hotend will preheat before starting to check +// the temperature. This value should NOT be set to the time it takes the +// hot end to reach the target temperature, but the time it takes to reach +// the minimum temperature your thermistor can read. The lower the better/safer. +// This shouldn't need to be more than 30 seconds (30000) +//#define MILLISECONDS_PREHEAT_TIME 0 + +// @section extruder + +// Extruder runout prevention. +// If the machine is idle and the temperature over MINTEMP +// then extrude some filament every couple of SECONDS. +//#define EXTRUDER_RUNOUT_PREVENT +#if ENABLED(EXTRUDER_RUNOUT_PREVENT) + #define EXTRUDER_RUNOUT_MINTEMP 190 + #define EXTRUDER_RUNOUT_SECONDS 30 + #define EXTRUDER_RUNOUT_SPEED 1500 // (mm/m) + #define EXTRUDER_RUNOUT_EXTRUDE 5 // (mm) +#endif + +// @section temperature + +// Calibration for AD595 / AD8495 sensor to adjust temperature measurements. +// The final temperature is calculated as (measuredTemp * GAIN) + OFFSET. +#define TEMP_SENSOR_AD595_OFFSET 0.0 +#define TEMP_SENSOR_AD595_GAIN 1.0 +#define TEMP_SENSOR_AD8495_OFFSET 0.0 +#define TEMP_SENSOR_AD8495_GAIN 1.0 + +/** + * Controller Fan + * To cool down the stepper drivers and MOSFETs. + * + * The fan will turn on automatically whenever any stepper is enabled + * and turn off after a set period after all steppers are turned off. + */ +//#define USE_CONTROLLER_FAN +#if ENABLED(USE_CONTROLLER_FAN) + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled + #define CONTROLLERFAN_SPEED 255 // 255 == full speed +#endif + +// When first starting the main fan, run it at full speed for the +// given number of milliseconds. This gets the fan spinning reliably +// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) +#define FAN_KICKSTART_TIME 100 + +/** + * PWM Fan Scaling + * + * Define the min/max speeds for PWM fans (as set with M106). + * + * With these options the M106 0-255 value range is scaled to a subset + * to ensure that the fan has enough power to spin, or to run lower + * current fans with higher current. (e.g., 5V/12V fans with 12V/24V) + * Value 0 always turns off the fan. + * + * Define one or both of these to override the default 0-255 range. + */ +//#define FAN_MIN_PWM 50 +//#define FAN_MAX_PWM 128 + +/** + * FAST PWM FAN Settings + * + * Use to change the FAST FAN PWM frequency (if enabled in Configuration.h) + * Combinations of PWM Modes, prescale values and TOP resolutions are used internally to produce a + * frequency as close as possible to the desired frequency. + * + * FAST_PWM_FAN_FREQUENCY [undefined by default] + * Set this to your desired frequency. + * If left undefined this defaults to F = F_CPU/(2*255*1) + * ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers + * These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required + * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior. + * + * USE_OCR2A_AS_TOP [undefined by default] + * Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2: + * 16MHz MCUs: [62.5KHz, 31.4KHz (default), 7.8KHz, 3.92KHz, 1.95KHz, 977Hz, 488Hz, 244Hz, 60Hz, 122Hz, 30Hz] + * 20MHz MCUs: [78.1KHz, 39.2KHz (default), 9.77KHz, 4.9KHz, 2.44KHz, 1.22KHz, 610Hz, 305Hz, 153Hz, 76Hz, 38Hz] + * A greater range can be achieved by enabling USE_OCR2A_AS_TOP. But note that this option blocks the use of + * PWM on pin OC2A. Only use this option if you don't need PWM on 0C2A. (Check your schematic.) + * USE_OCR2A_AS_TOP sacrifices duty cycle control resolution to achieve this broader range of frequencies. + */ +#if ENABLED(FAST_PWM_FAN) + //#define FAST_PWM_FAN_FREQUENCY 31400 + //#define USE_OCR2A_AS_TOP +#endif + +// @section extruder + +/** + * Extruder cooling fans + * + * Extruder auto fans automatically turn on when their extruders' + * temperatures go above EXTRUDER_AUTO_FAN_TEMPERATURE. + * + * Your board's pins file specifies the recommended pins. Override those here + * or set to -1 to disable completely. + * + * Multiple extruders can be assigned to the same pin in which case + * the fan will turn on when any selected extruder is above the threshold. + */ +#define E0_AUTO_FAN_PIN 7 +#define E1_AUTO_FAN_PIN -1 +#define E2_AUTO_FAN_PIN -1 +#define E3_AUTO_FAN_PIN -1 +#define E4_AUTO_FAN_PIN -1 +#define E5_AUTO_FAN_PIN -1 +#define CHAMBER_AUTO_FAN_PIN -1 + +#define EXTRUDER_AUTO_FAN_TEMPERATURE 50 +#define EXTRUDER_AUTO_FAN_SPEED 255 // 255 == full speed +#define CHAMBER_AUTO_FAN_TEMPERATURE 30 +#define CHAMBER_AUTO_FAN_SPEED 255 + +/** + * Part-Cooling Fan Multiplexer + * + * This feature allows you to digitally multiplex the fan output. + * The multiplexer is automatically switched at tool-change. + * Set FANMUX[012]_PINs below for up to 2, 4, or 8 multiplexed fans. + */ +#define FANMUX0_PIN -1 +#define FANMUX1_PIN -1 +#define FANMUX2_PIN -1 + +/** + * M355 Case Light on-off / brightness + */ +//#define CASE_LIGHT_ENABLE +#if ENABLED(CASE_LIGHT_ENABLE) + //#define CASE_LIGHT_PIN 4 // Override the default pin if needed + #define INVERT_CASE_LIGHT false // Set true if Case Light is ON when pin is LOW + #define CASE_LIGHT_DEFAULT_ON true // Set default power-up state on + #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105 // Set default power-up brightness (0-255, requires PWM pin) + //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu + //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. + //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) + #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } + #endif +#endif + +// @section homing + +// If you want endstops to stay on (by default) even when not homing +// enable this option. Override at any time with M120, M121. +//#define ENDSTOPS_ALWAYS_ON_DEFAULT + +// @section extras + +//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats. + +// Employ an external closed loop controller. Override pins here if needed. +//#define EXTERNAL_CLOSED_LOOP_CONTROLLER +#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER) + //#define CLOSED_LOOP_ENABLE_PIN -1 + //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1 +#endif + +/** + * Dual Steppers / Dual Endstops + * + * This section will allow you to use extra E drivers to drive a second motor for X, Y, or Z axes. + * + * For example, set X_DUAL_STEPPER_DRIVERS setting to use a second motor. If the motors need to + * spin in opposite directions set INVERT_X2_VS_X_DIR. If the second motor needs its own endstop + * set X_DUAL_ENDSTOPS. This can adjust for "racking." Use X2_USE_ENDSTOP to set the endstop plug + * that should be used for the second endstop. Extra endstops will appear in the output of 'M119'. + * + * Use X_DUAL_ENDSTOP_ADJUSTMENT to adjust for mechanical imperfection. After homing both motors + * this offset is applied to the X2 motor. To find the offset home the X axis, and measure the error + * in X2. Dual endstop offsets can be set at runtime with 'M666 X Y Z'. + */ + +//#define X_DUAL_STEPPER_DRIVERS +#if ENABLED(X_DUAL_STEPPER_DRIVERS) + #define INVERT_X2_VS_X_DIR true // Set 'true' if X motors should rotate in opposite directions + //#define X_DUAL_ENDSTOPS + #if ENABLED(X_DUAL_ENDSTOPS) + #define X2_USE_ENDSTOP _XMAX_ + #define X_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Y_DUAL_STEPPER_DRIVERS +#if ENABLED(Y_DUAL_STEPPER_DRIVERS) + #define INVERT_Y2_VS_Y_DIR true // Set 'true' if Y motors should rotate in opposite directions + //#define Y_DUAL_ENDSTOPS + #if ENABLED(Y_DUAL_ENDSTOPS) + #define Y2_USE_ENDSTOP _YMAX_ + #define Y_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Z_DUAL_STEPPER_DRIVERS +#if ENABLED(Z_DUAL_STEPPER_DRIVERS) + //#define Z_DUAL_ENDSTOPS + #if ENABLED(Z_DUAL_ENDSTOPS) + #define Z2_USE_ENDSTOP _XMAX_ + #define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Z_TRIPLE_STEPPER_DRIVERS +#if ENABLED(Z_TRIPLE_STEPPER_DRIVERS) + //#define Z_TRIPLE_ENDSTOPS + #if ENABLED(Z_TRIPLE_ENDSTOPS) + #define Z2_USE_ENDSTOP _XMAX_ + #define Z3_USE_ENDSTOP _YMAX_ + #define Z_TRIPLE_ENDSTOPS_ADJUSTMENT2 0 + #define Z_TRIPLE_ENDSTOPS_ADJUSTMENT3 0 + #endif +#endif + +/** + * Dual X Carriage + * + * This setup has two X carriages that can move independently, each with its own hotend. + * The carriages can be used to print an object with two colors or materials, or in + * "duplication mode" it can print two identical or X-mirrored objects simultaneously. + * The inactive carriage is parked automatically to prevent oozing. + * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. + * By default the X2 stepper is assigned to the first unused E plug on the board. + * + * The following Dual X Carriage modes can be selected with M605 S: + * + * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel + * results as long as it supports dual X-carriages. (M605 S0) + * + * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so + * that additional slicer support is not required. (M605 S1) + * + * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with + * the first X-carriage and extruder, to print 2 copies of the same object at the same time. + * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and + * follow with M605 S2 to initiate duplicated movement. + * + * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates + * the movement of the first except the second extruder is reversed in the X axis. + * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and + * follow with M605 S3 to initiate mirrored movement. + */ +//#define DUAL_X_CARRIAGE +#if ENABLED(DUAL_X_CARRIAGE) + #define X1_MIN_POS X_MIN_POS // Set to X_MIN_POS + #define X1_MAX_POS X_BED_SIZE // Set a maximum so the first X-carriage can't hit the parked second X-carriage + #define X2_MIN_POS 80 // Set a minimum to ensure the second X-carriage can't hit the parked first X-carriage + #define X2_MAX_POS 353 // Set this to the distance between toolheads when both heads are homed + #define X2_HOME_DIR 1 // Set to 1. The second X-carriage always homes to the maximum endstop position + #define X2_HOME_POS X2_MAX_POS // Default X2 home position. Set to X2_MAX_POS. + // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software + // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops + // without modifying the firmware (through the "M218 T1 X???" command). + // Remember: you should set the second extruder x-offset to 0 in your slicer. + + // This is the default power-up mode which can be later using M605. + #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_AUTO_PARK_MODE + + // Default x offset in duplication mode (typically set to half print bed width) + #define DEFAULT_DUPLICATION_X_OFFSET 100 + +#endif // DUAL_X_CARRIAGE + +// Activate a solenoid on the active extruder with M380. Disable all with M381. +// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid. +//#define EXT_SOLENOID + +// @section homing + +// Homing hits each endstop, retracts by these distances, then does a slower bump. +#define X_HOME_BUMP_MM 5 +#define Y_HOME_BUMP_MM 5 +#define Z_HOME_BUMP_MM 2 +#define HOMING_BUMP_DIVISOR { 2, 2, 4 } // Re-Bump Speed Divisor (Divides the Homing Feedrate) +#define QUICK_HOME // If homing includes X and Y, do a diagonal move initially +//#define HOMING_BACKOFF_MM { 2, 2, 2 } // (mm) Move away from the endstops after homing + +// When G28 is called, this option will make Y home before X +//#define HOME_Y_BEFORE_X + +// Enable this if X or Y can't home without homing the other axis first. +//#define CODEPENDENT_XY_HOMING + +#if ENABLED(BLTOUCH) + /** + * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES + * Do not activate settings that the probe might not understand. Clones might misunderstand + * advanced commands. + * + * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then + * check the wiring of the BROWN, RED and ORANGE wires. + * + * Note: If the trigger signal of your probe is not being recognized, it has been very often + * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable" + * like they would be with a real switch. So please check the wiring first. + * + * Settings for all BLTouch and clone probes: + */ + + // Safety: The probe needs time to recognize the command. + // Minimum command delay (ms). Enable and increase if needed. + //#define BLTOUCH_DELAY 500 + + /** + * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones: + */ + + // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful + // in special cases, like noisy or filtered input configurations. + //#define BLTOUCH_FORCE_SW_MODE + + /** + * Settings for BLTouch Smart 3.0 and 3.1 + * Summary: + * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes + * - High-Speed mode + * - Disable LCD voltage options + */ + + /** + * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller! + * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup. + * If disabled, OD mode is the hard-coded default on 3.0 + * On startup, Marlin will compare its eeprom to this vale. If the selected mode + * differs, a mode set eeprom write will be completed at initialization. + * Use the option below to force an eeprom write to a V3.1 probe regardless. + */ + //#define BLTOUCH_SET_5V_MODE + + /** + * Safety: Activate if connecting a probe with an unknown voltage mode. + * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0 + * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write ) + * To preserve the life of the probe, use this once then turn it off and re-flash. + */ + //#define BLTOUCH_FORCE_MODE_SET + + /** + * Use "HIGH SPEED" mode for probing. + * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems. + * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function + * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state. + */ + //#define BLTOUCH_HS_MODE + + // Safety: Enable voltage mode settings in the LCD menu. + //#define BLTOUCH_LCD_VOLTAGE_MENU + +#endif // BLTOUCH + +/** + * Z Steppers Auto-Alignment + * Add the G34 command to align multiple Z steppers using a bed probe. + */ +//#define Z_STEPPER_AUTO_ALIGN +#if ENABLED(Z_STEPPER_AUTO_ALIGN) + // Define probe X and Y positions for Z1, Z2 [, Z3] + #define Z_STEPPER_ALIGN_X { 10, 150, 290 } + #define Z_STEPPER_ALIGN_Y { 290, 10, 290 } + // Set number of iterations to align + #define Z_STEPPER_ALIGN_ITERATIONS 3 + // Enable to restore leveling setup after operation + #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + + // Use the amplification factor to de-/increase correction step. + // In case the stepper (spindle) position is further out than the test point + // Use a value > 1. NOTE: This may cause instability + #define Z_STEPPER_ALIGN_AMP 1.0 + // Stop criterion. If the accuracy is better than this stop iterating early + #define Z_STEPPER_ALIGN_ACC 0.02 +#endif + +// @section machine + +#define AXIS_RELATIVE_MODES { false, false, false, false } + +// Add a Duplicate option for well-separated conjoined nozzles +//#define MULTI_NOZZLE_DUPLICATION + +// By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step. +#define INVERT_X_STEP_PIN false +#define INVERT_Y_STEP_PIN false +#define INVERT_Z_STEP_PIN false +#define INVERT_E_STEP_PIN false + +// Default stepper release if idle. Set to 0 to deactivate. +// Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true. +// Time can be set by M18 and M84. +#define DEFAULT_STEPPER_DEACTIVE_TIME 120 +#define DISABLE_INACTIVE_X true +#define DISABLE_INACTIVE_Y true +#define DISABLE_INACTIVE_Z true // Set to false if the nozzle will fall down on your printed part when print has finished. +#define DISABLE_INACTIVE_E true + +#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate +#define DEFAULT_MINTRAVELFEEDRATE 0.0 + +//#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated + +// @section lcd + +#if EITHER(ULTIPANEL, EXTENSIBLE_UI) + #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #if ENABLED(ULTIPANEL) + #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" + #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen + #endif +#endif + +// @section extras + +// minimum time in microseconds that a movement needs to take if the buffer is emptied. +#define DEFAULT_MINSEGMENTTIME 20000 + +// If defined the movements slow down when the look ahead buffer is only half full +#define SLOWDOWN + +// Frequency limit +// See nophead's blog for more info +// Not working O +//#define XY_FREQUENCY_LIMIT 15 + +// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end +// of the buffer and all stops. This should not be much greater than zero and should only be changed +// if unwanted behavior is observed on a user's machine when running at very slow speeds. +#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s) + +// +// Backlash Compensation +// Adds extra movement to axes on direction-changes to account for backlash. +// +//#define BACKLASH_COMPENSATION +#if ENABLED(BACKLASH_COMPENSATION) + // Define values for backlash distance and correction. + // If BACKLASH_GCODE is enabled these values are the defaults. + #define BACKLASH_DISTANCE_MM { 0, 0, 0 } // (mm) + #define BACKLASH_CORRECTION 0.0 // 0.0 = no correction; 1.0 = full correction + + // Set BACKLASH_SMOOTHING_MM to spread backlash correction over multiple segments + // to reduce print artifacts. (Enabling this is costly in memory and computation!) + //#define BACKLASH_SMOOTHING_MM 3 // (mm) + + // Add runtime configuration and tuning of backlash values (M425) + //#define BACKLASH_GCODE + + #if ENABLED(BACKLASH_GCODE) + // Measure the Z backlash when probing (G29) and set with "M425 Z" + #define MEASURE_BACKLASH_WHEN_PROBING + + #if ENABLED(MEASURE_BACKLASH_WHEN_PROBING) + // When measuring, the probe will move up to BACKLASH_MEASUREMENT_LIMIT + // mm away from point of contact in BACKLASH_MEASUREMENT_RESOLUTION + // increments while checking for the contact to be broken. + #define BACKLASH_MEASUREMENT_LIMIT 0.5 // (mm) + #define BACKLASH_MEASUREMENT_RESOLUTION 0.005 // (mm) + #define BACKLASH_MEASUREMENT_FEEDRATE Z_PROBE_SPEED_SLOW // (mm/m) + #endif + #endif +#endif + +/** + * Automatic backlash, position and hotend offset calibration + * + * Enable G425 to run automatic calibration using an electrically- + * conductive cube, bolt, or washer mounted on the bed. + * + * G425 uses the probe to touch the top and sides of the calibration object + * on the bed and measures and/or correct positional offsets, axis backlash + * and hotend offsets. + * + * Note: HOTEND_OFFSET and CALIBRATION_OBJECT_CENTER must be set to within + * ±5mm of true values for G425 to succeed. + */ +//#define CALIBRATION_GCODE +#if ENABLED(CALIBRATION_GCODE) + + #define CALIBRATION_MEASUREMENT_RESOLUTION 0.01 // mm + + #define CALIBRATION_FEEDRATE_SLOW 60 // mm/m + #define CALIBRATION_FEEDRATE_FAST 1200 // mm/m + #define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/m + + // The following parameters refer to the conical section of the nozzle tip. + #define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm + #define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm + + // Uncomment to enable reporting (required for "G425 V", but consumes PROGMEM). + //#define CALIBRATION_REPORTING + + // The true location and dimension the cube/bolt/washer on the bed. + #define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0} // mm + #define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0} // mm + + // Comment out any sides which are unreachable by the probe. For best + // auto-calibration results, all sides must be reachable. + #define CALIBRATION_MEASURE_RIGHT + #define CALIBRATION_MEASURE_FRONT + #define CALIBRATION_MEASURE_LEFT + #define CALIBRATION_MEASURE_BACK + + // Probing at the exact top center only works if the center is flat. If + // probing on a screwhead or hollow washer, probe near the edges. + //#define CALIBRATION_MEASURE_AT_TOP_EDGES + + // Define pin which is read during calibration + #ifndef CALIBRATION_PIN + #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop + #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin + //#define CALIBRATION_PIN_PULLDOWN + #define CALIBRATION_PIN_PULLUP + #endif +#endif + +/** + * Adaptive Step Smoothing increases the resolution of multi-axis moves, particularly at step frequencies + * below 1kHz (for AVR) or 10kHz (for ARM), where aliasing between axes in multi-axis moves causes audible + * vibration and surface artifacts. The algorithm adapts to provide the best possible step smoothing at the + * lowest stepping frequencies. + */ +//#define ADAPTIVE_STEP_SMOOTHING + +/** + * Custom Microstepping + * Override as-needed for your setup. Up to 3 MS pins are supported. + */ +//#define MICROSTEP1 LOW,LOW,LOW +//#define MICROSTEP2 HIGH,LOW,LOW +//#define MICROSTEP4 LOW,HIGH,LOW +//#define MICROSTEP8 HIGH,HIGH,LOW +//#define MICROSTEP16 LOW,LOW,HIGH +//#define MICROSTEP32 HIGH,LOW,HIGH + +// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU. +#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16] + +/** + * @section stepper motor current + * + * Some boards have a means of setting the stepper motor current via firmware. + * + * The power on motor currents are set by: + * PWM_MOTOR_CURRENT - used by MINIRAMBO & ULTIMAIN_2 + * known compatible chips: A4982 + * DIGIPOT_MOTOR_CURRENT - used by BQ_ZUM_MEGA_3D, RAMBO & SCOOVO_X9H + * known compatible chips: AD5206 + * DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2 + * known compatible chips: MCP4728 + * DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, AZTEEG_X5_MINI_WIFI, MIGHTYBOARD_REVE + * known compatible chips: MCP4451, MCP4018 + * + * Motor currents can also be set by M907 - M910 and by the LCD. + * M907 - applies to all. + * M908 - BQ_ZUM_MEGA_3D, RAMBO, PRINTRBOARD_REVF, RIGIDBOARD_V2 & SCOOVO_X9H + * M909, M910 & LCD - only PRINTRBOARD_REVF & RIGIDBOARD_V2 + */ +//#define PWM_MOTOR_CURRENT { 1300, 1300, 1250 } // Values in milliamps +//#define DIGIPOT_MOTOR_CURRENT { 135,135,135,135,135 } // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A) +//#define DAC_MOTOR_CURRENT_DEFAULT { 70, 80, 90, 80 } // Default drive percent - X, Y, Z, E axis + +// Use an I2C based DIGIPOT (e.g., Azteeg X3 Pro) +//#define DIGIPOT_I2C +#if ENABLED(DIGIPOT_I2C) && !defined(DIGIPOT_I2C_ADDRESS_A) + /** + * Common slave addresses: + * + * A (A shifted) B (B shifted) IC + * Smoothie 0x2C (0x58) 0x2D (0x5A) MCP4451 + * AZTEEG_X3_PRO 0x2C (0x58) 0x2E (0x5C) MCP4451 + * AZTEEG_X5_MINI 0x2C (0x58) 0x2E (0x5C) MCP4451 + * AZTEEG_X5_MINI_WIFI 0x58 0x5C MCP4451 + * MIGHTYBOARD_REVE 0x2F (0x5E) MCP4018 + */ + #define DIGIPOT_I2C_ADDRESS_A 0x2C // unshifted slave address for first DIGIPOT + #define DIGIPOT_I2C_ADDRESS_B 0x2D // unshifted slave address for second DIGIPOT +#endif + +//#define DIGIPOT_MCP4018 // Requires library from https://github.com/stawel/SlowSoftI2CMaster +#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8 MKS SBASE: 5 +// Actual motor currents in Amps. The number of entries must match DIGIPOT_I2C_NUM_CHANNELS. +// These correspond to the physical drivers, so be mindful if the order is changed. +#define DIGIPOT_I2C_MOTOR_CURRENTS { 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0 } // AZTEEG_X3_PRO + +//=========================================================================== +//=============================Additional Features=========================== +//=========================================================================== + +// @section lcd + +// Change values more rapidly when the encoder is rotated faster +#define ENCODER_RATE_MULTIPLIER +#if ENABLED(ENCODER_RATE_MULTIPLIER) + #define ENCODER_10X_STEPS_PER_SEC 75 // (steps/s) Encoder rate for 10x speed + #define ENCODER_100X_STEPS_PER_SEC 160 // (steps/s) Encoder rate for 100x speed +#endif + +// Play a beep when the feedrate is changed from the Status Screen +//#define BEEP_ON_FEEDRATE_CHANGE +#if ENABLED(BEEP_ON_FEEDRATE_CHANGE) + #define FEEDRATE_CHANGE_BEEP_DURATION 10 + #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 +#endif + +// Include a page of printer information in the LCD Main Menu +#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif + +// Scroll a longer status message into view +#define STATUS_MESSAGE_SCROLLING + +// On the Info Screen, display XY with one decimal place when possible +//#define LCD_DECIMAL_SMALL_XY + +// The timeout (in ms) to return to the status screen from sub-menus +//#define LCD_TIMEOUT_TO_STATUS 15000 + +// Add an 'M73' G-code to set the current percentage +#define LCD_SET_PROGRESS_MANUALLY + +#if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS + //#define LCD_PROGRESS_BAR // Show a progress bar on HD44780 LCDs for SD printing + #if ENABLED(LCD_PROGRESS_BAR) + #define PROGRESS_BAR_BAR_TIME 2000 // (ms) Amount of time to show the bar + #define PROGRESS_BAR_MSG_TIME 3000 // (ms) Amount of time to show the status message + #define PROGRESS_MSG_EXPIRE 0 // (ms) Amount of time to retain the status message (0=forever) + //#define PROGRESS_MSG_ONCE // Show the message for MSG_TIME then clear it + //#define LCD_PROGRESS_BAR_TEST // Add a menu item to test the progress bar + #endif +#endif + +/** + * LED Control Menu + * Enable this feature to add LED Control to the LCD menu + */ +//#define LED_CONTROL_MENU +#if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif +#endif // LED_CONTROL_MENU + +#if ENABLED(SDSUPPORT) + + // Some RAMPS and other boards don't detect when an SD card is inserted. You can work + // around this by connecting a push button or single throw switch to the pin defined + // as SD_DETECT_PIN in your board's pins definitions. + // This setting should be disabled unless you are using a push button, pulling the pin to ground. + // Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER). + #define SD_DETECT_INVERTED + + #define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished + #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place. + + // Reverse SD sort to show "more recent" files first, according to the card's FAT. + // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended. + #define SDCARD_RATHERRECENTFIRST + + #define SD_MENU_CONFIRM_START // Confirm the selected SD file before printing + + //#define MENU_ADDAUTOSTART // Add a menu option to run auto#.g files + + #define EVENT_GCODE_SD_STOP "G28XY" // G-code to run on Stop Print (e.g., "G28XY" or "G27") + + /** + * Continue after Power-Loss (Creality3D) + * + * Store the current state to the SD Card at the start of each layer + * during SD printing. If the recovery file is found at boot time, present + * an option on the LCD screen to continue the print from the last-known + * point in the file. + */ + //#define POWER_LOSS_RECOVERY + #if ENABLED(POWER_LOSS_RECOVERY) + //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume + //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. + + // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, + // especially with "vase mode" printing. Set too high and vases cannot be continued. + #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + #endif + + /** + * Sort SD file listings in alphabetical order. + * + * With this option enabled, items on SD cards will be sorted + * by name for easier navigation. + * + * By default... + * + * - Use the slowest -but safest- method for sorting. + * - Folders are sorted to the top. + * - The sort key is statically allocated. + * - No added G-code (M34) support. + * - 40 item sorting limit. (Items after the first 40 are unsorted.) + * + * SD sorting uses static allocation (as set by SDSORT_LIMIT), allowing the + * compiler to calculate the worst-case usage and throw an error if the SRAM + * limit is exceeded. + * + * - SDSORT_USES_RAM provides faster sorting via a static directory buffer. + * - SDSORT_USES_STACK does the same, but uses a local stack-based buffer. + * - SDSORT_CACHE_NAMES will retain the sorted file listing in RAM. (Expensive!) + * - SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible. (Use with caution!) + */ + #define SDCARD_SORT_ALPHA + + // SD Card Sorting options + #if ENABLED(SDCARD_SORT_ALPHA) + #define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). Costs 27 bytes each. + #define FOLDER_SORTING -1 // -1=above 0=none 1=below + #define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 g-code. + #define SDSORT_USES_RAM false // Pre-allocate a static array for faster pre-sorting. + #define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.) + #define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option. + #define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use! + #define SDSORT_CACHE_VFATS 2 // Maximum number of 13-byte VFAT entries to use for sorting. + // Note: Only affects SCROLL_LONG_FILENAMES with SDSORT_CACHE_NAMES but not SDSORT_DYNAMIC_RAM. + #endif + + // This allows hosts to request long names for files and folders with M33 + #define LONG_FILENAME_HOST_SUPPORT + + // Enable this option to scroll long filenames in the SD card menu + #define SCROLL_LONG_FILENAMES + + // Leave the heaters on after Stop Print (not recommended!) + //#define SD_ABORT_NO_COOLDOWN + + /** + * This option allows you to abort SD printing when any endstop is triggered. + * This feature must be enabled with "M540 S1" or from the LCD menu. + * To have any effect, endstops must be enabled during SD printing. + */ + //#define SD_ABORT_ON_ENDSTOP_HIT + + /** + * This option makes it easier to print the same SD Card file again. + * On print completion the LCD Menu will open with the file selected. + * You can just click to start the print, or navigate elsewhere. + */ + //#define SD_REPRINT_LAST_SELECTED_FILE + + /** + * Auto-report SdCard status with M27 S + */ + //#define AUTO_REPORT_SD_STATUS + + /** + * Support for USB thumb drives using an Arduino USB Host Shield or + * equivalent MAX3421E breakout board. The USB thumb drive will appear + * to Marlin as an SD card. + * + * The MAX3421E must be assigned the same pins as the SD card reader, with + * the following pin mapping: + * + * SCLK, MOSI, MISO --> SCLK, MOSI, MISO + * INT --> SD_DETECT_PIN + * SS --> SDSS + */ + //#define USB_FLASH_DRIVE_SUPPORT + #if ENABLED(USB_FLASH_DRIVE_SUPPORT) + #define USB_CS_PIN SDSS + #define USB_INTR_PIN SD_DETECT_PIN + #endif + + /** + * When using a bootloader that supports SD-Firmware-Flashing, + * add a menu item to activate SD-FW-Update on the next reboot. + * + * Requires ATMEGA2560 (Arduino Mega) + * + * Tested with this bootloader: + * https://github.com/FleetProbe/MicroBridge-Arduino-ATMega2560 + */ + //#define SD_FIRMWARE_UPDATE + #if ENABLED(SD_FIRMWARE_UPDATE) + #define SD_FIRMWARE_UPDATE_EEPROM_ADDR 0x1FF + #define SD_FIRMWARE_UPDATE_ACTIVE_VALUE 0xF0 + #define SD_FIRMWARE_UPDATE_INACTIVE_VALUE 0xFF + #endif + + // Add an optimized binary file transfer mode, initiated with 'M28 B1' + //#define BINARY_FILE_TRANSFER + + #if HAS_SDCARD_CONNECTION + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD + #endif + +#endif // SDSUPPORT + +/** + * By default an onboard SD card reader may be shared as a USB mass- + * storage device. This option hides the SD card from the host PC. + */ +//#define NO_SD_HOST_DRIVE // Disable SD Card access over USB (for security). + +/** + * Additional options for Graphical Displays + * + * Use the optimizations here to improve printing performance, + * which can be adversely affected by graphical display drawing, + * especially when doing several short moves, and when printing + * on DELTA and SCARA machines. + * + * Some of these options may result in the display lagging behind + * controller events, as there is a trade-off between reliable + * printing performance versus fast display updates. + */ +#if HAS_GRAPHICAL_LCD + // Show SD percentage next to the progress bar + //#define DOGM_SD_PERCENT + + // Enable to save many cycles by drawing a hollow frame on the Info Screen + #define XYZ_HOLLOW_FRAME + + // Enable to save many cycles by drawing a hollow frame on Menu Screens + #define MENU_HOLLOW_FRAME + + // A bigger font is available for edit items. Costs 3120 bytes of PROGMEM. + // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. + #define USE_BIG_EDIT_FONT + + // A smaller font may be used on the Info Screen. Costs 2300 bytes of PROGMEM. + // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. + //#define USE_SMALL_INFOFONT + + // Enable this option and reduce the value to optimize screen updates. + // The normal delay is 10µs. Use the lowest value that still gives a reliable display. + //#define DOGM_SPI_DELAY_US 5 + + // Swap the CW/CCW indicators in the graphics overlay + //#define OVERLAY_GFX_REVERSE + + /** + * ST7920-based LCDs can emulate a 16 x 4 character display using + * the ST7920 character-generator for very fast screen updates. + * Enable LIGHTWEIGHT_UI to use this special display mode. + * + * Since LIGHTWEIGHT_UI has limited space, the position and status + * message occupy the same line. Set STATUS_EXPIRE_SECONDS to the + * length of time to display the status message before clearing. + * + * Set STATUS_EXPIRE_SECONDS to zero to never clear the status. + * This will prevent position updates from being displayed. + */ + #if ENABLED(U8GLIB_ST7920) + //#define LIGHTWEIGHT_UI + #if ENABLED(LIGHTWEIGHT_UI) + #define STATUS_EXPIRE_SECONDS 20 + #endif + #endif + + /** + * Status (Info) Screen customizations + * These options may affect code size and screen render time. + * Custom status screens can forcibly override these settings. + */ + //#define STATUS_COMBINE_HEATERS // Use combined heater images instead of separate ones + //#define STATUS_HOTEND_NUMBERLESS // Use plain hotend icons instead of numbered ones (with 2+ hotends) + #define STATUS_HOTEND_INVERTED // Show solid nozzle bitmaps when heating (Requires STATUS_HOTEND_ANIM) + #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating + #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating + #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap + //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap + //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames + #define STATUS_HEAT_PERCENT // Show heating in a progress bar + //#define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash) + + // Frivolous Game Options + //#define MARLIN_BRICKOUT + //#define MARLIN_INVADERS + //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu + +#endif // HAS_GRAPHICAL_LCD + +// @section safety + +/** + * The watchdog hardware timer will do a reset and disable all outputs + * if the firmware gets too overloaded to read the temperature sensors. + * + * If you find that watchdog reboot causes your AVR board to hang forever, + * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO. + * NOTE: This method is less reliable as it can only catch hangups while + * interrupts are enabled. + */ +#define USE_WATCHDOG +#if ENABLED(USE_WATCHDOG) + //#define WATCHDOG_RESET_MANUAL +#endif + +// @section lcd + +/** + * Babystepping enables movement of the axes by tiny increments without changing + * the current position values. This feature is used primarily to adjust the Z + * axis in the first layer of a print in real-time. + * + * Warning: Does not respect endstops! + */ +#define BABYSTEPPING +#if ENABLED(BABYSTEPPING) + //#define BABYSTEP_WITHOUT_HOMING + //#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA! + #define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way + #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion. + + #define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping. + #if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING) + #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds. + // Note: Extra time may be added to mitigate controller latency. + //#define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement). + //#define MOVE_Z_WHEN_IDLE // Jump to the move Z menu on doubleclick when printer is idle. + #if ENABLED(MOVE_Z_WHEN_IDLE) + #define MOVE_Z_IDLE_MULTIPLICATOR 1 // Multiply 1mm by this factor for the move step size. + #endif + #endif + + //#define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28 + + //#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping + #if ENABLED(BABYSTEP_ZPROBE_OFFSET) + //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets + //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor + #endif +#endif + +// @section extruder + +/** + * Linear Pressure Control v1.5 + * + * Assumption: advance [steps] = k * (delta velocity [steps/s]) + * K=0 means advance disabled. + * + * NOTE: K values for LIN_ADVANCE 1.5 differ from earlier versions! + * + * Set K around 0.22 for 3mm PLA Direct Drive with ~6.5cm between the drive gear and heatbreak. + * Larger K values will be needed for flexible filament and greater distances. + * If this algorithm produces a higher speed offset than the extruder can handle (compared to E jerk) + * print acceleration will be reduced during the affected moves to keep within the limit. + * + * See http://marlinfw.org/docs/features/lin_advance.html for full instructions. + * Mention @Sebastianv650 on GitHub to alert the author of any issues. + */ +//#define LIN_ADVANCE +#if ENABLED(LIN_ADVANCE) + //#define EXTRA_LIN_ADVANCE_K // Enable for second linear advance constants + #define LIN_ADVANCE_K 0.22 // Unit: mm compression per 1mm/s extruder speed + //#define LA_DEBUG // If enabled, this will generate debug information output over USB. +#endif + +// @section leveling + +#if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL) + // Override the mesh area if the automatic (max) area is too large + //#define MESH_MIN_X MESH_INSET + //#define MESH_MIN_Y MESH_INSET + //#define MESH_MAX_X X_BED_SIZE - (MESH_INSET) + //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET) +#endif + +/** + * Repeatedly attempt G29 leveling until it succeeds. + * Stop after G29_MAX_RETRIES attempts. + */ +//#define G29_RETRY_AND_RECOVER +#if ENABLED(G29_RETRY_AND_RECOVER) + #define G29_MAX_RETRIES 3 + #define G29_HALT_ON_FAILURE + /** + * Specify the GCODE commands that will be executed when leveling succeeds, + * between attempts, and after the maximum number of retries have been tried. + */ + #define G29_SUCCESS_COMMANDS "M117 Bed leveling done." + #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0" + #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1" + +#endif + +// @section extras + +// +// G2/G3 Arc Support +// +#define ARC_SUPPORT // Disable this feature to save ~3226 bytes +#if ENABLED(ARC_SUPPORT) + #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles + //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes +#endif + +// Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes. +//#define BEZIER_CURVE_SUPPORT + +/** + * G38 Probe Target + * + * This option adds G38.2 and G38.3 (probe towards target) + * and optionally G38.4 and G38.5 (probe away from target). + * Set MULTIPLE_PROBING for G38 to probe more than once. + */ +//#define G38_PROBE_TARGET +#if ENABLED(G38_PROBE_TARGET) + //#define G38_PROBE_AWAY // Include G38.4 and G38.5 to probe away from target + #define G38_MINIMUM_MOVE 0.0275 // (mm) Minimum distance that will produce a move. +#endif + +// Moves (or segments) with fewer steps than this will be joined with the next move +#define MIN_STEPS_PER_SEGMENT 6 + +/** + * Minimum delay after setting the stepper DIR (in ns) + * 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire) + * 20 : Minimum for TMC2xxx drivers + * 200 : Minimum for A4988 drivers + * 400 : Minimum for A5984 drivers + * 500 : Minimum for LV8729 drivers (guess, no info in datasheet) + * 650 : Minimum for DRV8825 drivers + * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet) + * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet) + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MINIMUM_STEPPER_DIR_DELAY 650 + +/** + * Minimum stepper driver pulse width (in µs) + * 0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers + * 0 : Minimum 500ns for LV8729, adjusted in stepper.h + * 1 : Minimum for A4988 and A5984 stepper drivers + * 2 : Minimum for DRV8825 stepper drivers + * 3 : Minimum for TB6600 stepper drivers + * 30 : Minimum for TB6560 stepper drivers + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MINIMUM_STEPPER_PULSE 2 + +/** + * Maximum stepping rate (in Hz) the stepper driver allows + * If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE) + * 500000 : Maximum for A4988 stepper driver + * 400000 : Maximum for TMC2xxx stepper drivers + * 250000 : Maximum for DRV8825 stepper driver + * 200000 : Maximum for LV8729 stepper driver + * 150000 : Maximum for TB6600 stepper driver + * 15000 : Maximum for TB6560 stepper driver + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MAXIMUM_STEPPER_RATE 250000 + +// @section temperature + +// Control heater 0 and heater 1 in parallel. +//#define HEATERS_PARALLEL + +//=========================================================================== +//================================= Buffers ================================= +//=========================================================================== + +// @section hidden + +// The number of linear motions that can be in the plan at any give time. +// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2 (e.g. 8, 16, 32) because shifts and ors are used to do the ring-buffering. +#if ENABLED(SDSUPPORT) + #define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller +#else + #define BLOCK_BUFFER_SIZE 16 // maximize block buffer +#endif + +// @section serial + +// The ASCII buffer for serial input +#define MAX_CMD_SIZE 96 +#define BUFSIZE 4 + +// Transmission to Host Buffer Size +// To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0. +// To buffer a simple "ok" you need 4 bytes. +// For ADVANCED_OK (M105) you need 32 bytes. +// For debug-echo: 128 bytes for the optimal speed. +// Other output doesn't need to be that speedy. +// :[0, 2, 4, 8, 16, 32, 64, 128, 256] +#define TX_BUFFER_SIZE 0 + +// Host Receive Buffer Size +// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough. +// To use flow control, set this buffer size to at least 1024 bytes. +// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048] +//#define RX_BUFFER_SIZE 1024 + +#if RX_BUFFER_SIZE >= 1024 + // Enable to have the controller send XON/XOFF control characters to + // the host to signal the RX buffer is becoming full. + //#define SERIAL_XON_XOFF +#endif + +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + +#if ENABLED(SDSUPPORT) + // Enable this option to collect and display the maximum + // RX queue usage after transferring a file to SD. + //#define SERIAL_STATS_MAX_RX_QUEUED + + // Enable this option to collect and display the number + // of dropped bytes after a file transfer to SD. + //#define SERIAL_STATS_DROPPED_RX +#endif + +// Enable an emergency-command parser to intercept certain commands as they +// enter the serial receive buffer, so they cannot be blocked. +// Currently handles M108, M112, M410 +// Does not work on boards using AT90USB (USBCON) processors! +//#define EMERGENCY_PARSER + +// Bad Serial-connections can miss a received command by sending an 'ok' +// Therefore some clients abort after 30 seconds in a timeout. +// Some other clients start sending commands while receiving a 'wait'. +// This "wait" is only sent when the buffer is empty. 1 second is a good value here. +//#define NO_TIMEOUTS 1000 // Milliseconds + +// Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary. +//#define ADVANCED_OK + +// Printrun may have trouble receiving long strings all at once. +// This option inserts short delays between lines of serial output. +#define SERIAL_OVERRUN_PROTECTION + +// @section extras + +/** + * Extra Fan Speed + * Adds a secondary fan speed for each print-cooling fan. + * 'M106 P T3-255' : Set a secondary speed for + * 'M106 P T2' : Use the set secondary speed + * 'M106 P T1' : Restore the previous fan speed + */ +//#define EXTRA_FAN_SPEED + +/** + * Firmware-based and LCD-controlled retract + * + * Add G10 / G11 commands for automatic firmware-based retract / recover. + * Use M207 and M208 to define parameters for retract / recover. + * + * Use M209 to enable or disable auto-retract. + * With auto-retract enabled, all G1 E moves within the set range + * will be converted to firmware-based retract/recover moves. + * + * Be sure to turn off auto-retract during filament change. + * + * Note that M207 / M208 / M209 settings are saved to EEPROM. + * + */ +//#define FWRETRACT +#if ENABLED(FWRETRACT) + #define FWRETRACT_AUTORETRACT // costs ~500 bytes of PROGMEM + #if ENABLED(FWRETRACT_AUTORETRACT) + #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over + #define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion + #endif + #define RETRACT_LENGTH 3 // Default retract length (positive mm) + #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change + #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) + #define RETRACT_ZRAISE 0 // Default retract Z-raise (mm) + #define RETRACT_RECOVER_LENGTH 0 // Default additional recover length (mm, added to retract length when recovering) + #define RETRACT_RECOVER_LENGTH_SWAP 0 // Default additional swap recover length (mm, added to retract length when recovering from extruder change) + #define RETRACT_RECOVER_FEEDRATE 8 // Default feedrate for recovering from retraction (mm/s) + #define RETRACT_RECOVER_FEEDRATE_SWAP 8 // Default feedrate for recovering from swap retraction (mm/s) + #if ENABLED(MIXING_EXTRUDER) + //#define RETRACT_SYNC_MIXING // Retract and restore all mixing steppers simultaneously + #endif +#endif + +/** + * Universal tool change settings. + * Applies to all types of extruders except where explicitly noted. + */ +#if EXTRUDERS > 1 + // Z raise distance for tool-change, as needed for some extruders + #define TOOLCHANGE_ZRAISE 2 // (mm) + //#define TOOLCHANGE_NO_RETURN // Never return to the previous position on tool-change + + // Retract and prime filament on tool-change + //#define TOOLCHANGE_FILAMENT_SWAP + #if ENABLED(TOOLCHANGE_FILAMENT_SWAP) + #define TOOLCHANGE_FIL_SWAP_LENGTH 12 // (mm) + #define TOOLCHANGE_FIL_EXTRA_PRIME 2 // (mm) + #define TOOLCHANGE_FIL_SWAP_RETRACT_SPEED 3600 // (mm/m) + #define TOOLCHANGE_FIL_SWAP_PRIME_SPEED 3600 // (mm/m) + #endif + + /** + * Position to park head during tool change. + * Doesn't apply to SWITCHING_TOOLHEAD, DUAL_X_CARRIAGE, or PARKING_EXTRUDER + */ + //#define TOOLCHANGE_PARK + #if ENABLED(TOOLCHANGE_PARK) + #define TOOLCHANGE_PARK_XY { X_MIN_POS + 10, Y_MIN_POS + 10 } + #define TOOLCHANGE_PARK_XY_FEEDRATE 6000 // (mm/m) + #endif +#endif + +/** + * Advanced Pause + * Experimental feature for filament change support and for parking the nozzle when paused. + * Adds the GCode M600 for initiating filament change. + * If PARK_HEAD_ON_PAUSE enabled, adds the GCode M125 to pause printing and park the nozzle. + * + * Requires an LCD display. + * Requires NOZZLE_PARK_FEATURE. + * This feature is required for the default FILAMENT_RUNOUT_SCRIPT. + */ +#define ADVANCED_PAUSE_FEATURE +#if ENABLED(ADVANCED_PAUSE_FEATURE) + #define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate. + #define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract. + // This short retract is done immediately, before parking the nozzle. + #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast. + #define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. + #define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload. + // For Bowden, the full length of the tube and nozzle. + // For direct drive, the full length of the nozzle. + // Set to 0 for manual unloading. + #define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load. + #define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material. + // 0 to disable start loading and skip to fast load only + #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast. + #define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. + #define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle. + // For Bowden, the full length of the tube and nozzle. + // For direct drive, the full length of the nozzle. + //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted. + #define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate. + #define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading. + // Set to 0 for manual extrusion. + // Filament can be extruded repeatedly from the Filament Change menu + // until extrusion is consistent, and to purge old filament. + #define ADVANCED_PAUSE_RESUME_PRIME 0 // (mm) Extra distance to prime nozzle after returning from park. + //#define ADVANCED_PAUSE_FANS_PAUSE // Turn off print-cooling fans while the machine is paused. + + // Filament Unload does a Retract, Delay, and Purge first: + #define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length. + #define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract. + #define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged. + + #define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety. + #define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed. + #define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change. + + //#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change. + //#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change + + //#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu. + //#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302) +#endif + +// @section tmc + +/** + * TMC26X Stepper Driver options + * + * The TMC26XStepper library is required for this stepper driver. + * https://github.com/trinamic/TMC26XStepper + */ +#if HAS_DRIVER(TMC26X) + + #if AXIS_DRIVER_TYPE_X(TMC26X) + #define X_MAX_CURRENT 1000 // (mA) + #define X_SENSE_RESISTOR 91 // (mOhms) + #define X_MICROSTEPS 16 // Number of microsteps + #endif + + #if AXIS_DRIVER_TYPE_X2(TMC26X) + #define X2_MAX_CURRENT 1000 + #define X2_SENSE_RESISTOR 91 + #define X2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Y(TMC26X) + #define Y_MAX_CURRENT 1000 + #define Y_SENSE_RESISTOR 91 + #define Y_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Y2(TMC26X) + #define Y2_MAX_CURRENT 1000 + #define Y2_SENSE_RESISTOR 91 + #define Y2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z(TMC26X) + #define Z_MAX_CURRENT 1000 + #define Z_SENSE_RESISTOR 91 + #define Z_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z2(TMC26X) + #define Z2_MAX_CURRENT 1000 + #define Z2_SENSE_RESISTOR 91 + #define Z2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z3(TMC26X) + #define Z3_MAX_CURRENT 1000 + #define Z3_SENSE_RESISTOR 91 + #define Z3_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E0(TMC26X) + #define E0_MAX_CURRENT 1000 + #define E0_SENSE_RESISTOR 91 + #define E0_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E1(TMC26X) + #define E1_MAX_CURRENT 1000 + #define E1_SENSE_RESISTOR 91 + #define E1_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E2(TMC26X) + #define E2_MAX_CURRENT 1000 + #define E2_SENSE_RESISTOR 91 + #define E2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E3(TMC26X) + #define E3_MAX_CURRENT 1000 + #define E3_SENSE_RESISTOR 91 + #define E3_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E4(TMC26X) + #define E4_MAX_CURRENT 1000 + #define E4_SENSE_RESISTOR 91 + #define E4_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E5(TMC26X) + #define E5_MAX_CURRENT 1000 + #define E5_SENSE_RESISTOR 91 + #define E5_MICROSTEPS 16 + #endif + +#endif // TMC26X + +// @section tmc_smart + +/** + * To use TMC2130, TMC2160, TMC2660, TMC5130, TMC5160 stepper drivers in SPI mode + * connect your SPI pins to the hardware SPI interface on your board and define + * the required CS pins in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 + * pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.). + * You may also use software SPI if you wish to use general purpose IO pins. + * + * To use TMC2208 stepper UART-configurable stepper drivers connect #_SERIAL_TX_PIN + * to the driver side PDN_UART pin with a 1K resistor. + * To use the reading capabilities, also connect #_SERIAL_RX_PIN to PDN_UART without + * a resistor. + * The drivers can also be used with hardware serial. + * + * TMCStepper library is required to use TMC stepper drivers. + * https://github.com/teemuatlut/TMCStepper + */ +#if HAS_TRINAMIC + + #define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current + #define INTERPOLATE true // Interpolate X/Y/Z_MICROSTEPS to 256 + + #if AXIS_IS_TMC(X) + #define X_CURRENT 800 // (mA) RMS current. Multiply by 1.414 for peak current. + #define X_MICROSTEPS 16 // 0..256 + #define X_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(X2) + #define X2_CURRENT 800 + #define X2_MICROSTEPS 16 + #define X2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Y) + #define Y_CURRENT 800 + #define Y_MICROSTEPS 16 + #define Y_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Y2) + #define Y2_CURRENT 800 + #define Y2_MICROSTEPS 16 + #define Y2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Z) + #define Z_CURRENT 800 + #define Z_MICROSTEPS 16 + #define Z_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Z2) + #define Z2_CURRENT 800 + #define Z2_MICROSTEPS 16 + #define Z2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Z3) + #define Z3_CURRENT 800 + #define Z3_MICROSTEPS 16 + #define Z3_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E0) + #define E0_CURRENT 800 + #define E0_MICROSTEPS 16 + #define E0_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E1) + #define E1_CURRENT 800 + #define E1_MICROSTEPS 16 + #define E1_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E2) + #define E2_CURRENT 800 + #define E2_MICROSTEPS 16 + #define E2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E3) + #define E3_CURRENT 800 + #define E3_MICROSTEPS 16 + #define E3_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E4) + #define E4_CURRENT 800 + #define E4_MICROSTEPS 16 + #define E4_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E5) + #define E5_CURRENT 800 + #define E5_MICROSTEPS 16 + #define E5_RSENSE 0.11 + #endif + + /** + * Override default SPI pins for TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160 drivers here. + * The default pins can be found in your board's pins file. + */ + //#define X_CS_PIN -1 + //#define Y_CS_PIN -1 + //#define Z_CS_PIN -1 + //#define X2_CS_PIN -1 + //#define Y2_CS_PIN -1 + //#define Z2_CS_PIN -1 + //#define Z3_CS_PIN -1 + //#define E0_CS_PIN -1 + //#define E1_CS_PIN -1 + //#define E2_CS_PIN -1 + //#define E3_CS_PIN -1 + //#define E4_CS_PIN -1 + //#define E5_CS_PIN -1 + + /** + * Software option for SPI driven drivers (TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160). + * The default SW SPI pins are defined the respective pins files, + * but you can override or define them here. + */ + //#define TMC_USE_SW_SPI + //#define TMC_SW_MOSI -1 + //#define TMC_SW_MISO -1 + //#define TMC_SW_SCK -1 + + /** + * Four TMC2209 drivers can use the same HW/SW serial port with hardware configured addresses. + * Set the address using jumpers on pins MS1 and MS2. + * Address | MS1 | MS2 + * 0 | LOW | LOW + * 1 | HIGH | LOW + * 2 | LOW | HIGH + * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. + */ + #define X_SLAVE_ADDRESS 0 + #define Y_SLAVE_ADDRESS 0 + #define Z_SLAVE_ADDRESS 0 + #define X2_SLAVE_ADDRESS 0 + #define Y2_SLAVE_ADDRESS 0 + #define Z2_SLAVE_ADDRESS 0 + #define Z3_SLAVE_ADDRESS 0 + #define E0_SLAVE_ADDRESS 0 + #define E1_SLAVE_ADDRESS 0 + #define E2_SLAVE_ADDRESS 0 + #define E3_SLAVE_ADDRESS 0 + #define E4_SLAVE_ADDRESS 0 + #define E5_SLAVE_ADDRESS 0 + + /** + * Software enable + * + * Use for drivers that do not use a dedicated enable pin, but rather handle the same + * function through a communication line such as SPI or UART. + */ + //#define SOFTWARE_DRIVER_ENABLE + + /** + * TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only + * Use Trinamic's ultra quiet stepping mode. + * When disabled, Marlin will use spreadCycle stepping mode. + */ + #define STEALTHCHOP_XY + #define STEALTHCHOP_Z + #define STEALTHCHOP_E + + /** + * Optimize spreadCycle chopper parameters by using predefined parameter sets + * or with the help of an example included in the library. + * Provided parameter sets are + * CHOPPER_DEFAULT_12V + * CHOPPER_DEFAULT_19V + * CHOPPER_DEFAULT_24V + * CHOPPER_DEFAULT_36V + * CHOPPER_PRUSAMK3_24V // Imported parameters from the official Prusa firmware for MK3 (24V) + * CHOPPER_MARLIN_119 // Old defaults from Marlin v1.1.9 + * + * Define you own with + * { , , hysteresis_start[1..8] } + */ + #define CHOPPER_TIMING CHOPPER_DEFAULT_24V + + /** + * Monitor Trinamic drivers for error conditions, + * like overtemperature and short to ground. + * In the case of overtemperature Marlin can decrease the driver current until error condition clears. + * Other detected conditions can be used to stop the current print. + * Relevant g-codes: + * M906 - Set or get motor current in milliamps using axis codes X, Y, Z, E. Report values if no axis codes given. + * M911 - Report stepper driver overtemperature pre-warn condition. + * M912 - Clear stepper driver overtemperature pre-warn condition flag. + * M122 - Report driver parameters (Requires TMC_DEBUG) + */ + //#define MONITOR_DRIVER_STATUS + + #if ENABLED(MONITOR_DRIVER_STATUS) + #define CURRENT_STEP_DOWN 50 // [mA] + #define REPORT_CURRENT_CHANGE + #define STOP_ON_ERROR + #endif + + /** + * TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only + * The driver will switch to spreadCycle when stepper speed is over HYBRID_THRESHOLD. + * This mode allows for faster movements at the expense of higher noise levels. + * STEALTHCHOP_(XY|Z|E) must be enabled to use HYBRID_THRESHOLD. + * M913 X/Y/Z/E to live tune the setting + */ + //#define HYBRID_THRESHOLD + + #define X_HYBRID_THRESHOLD 100 // [mm/s] + #define X2_HYBRID_THRESHOLD 100 + #define Y_HYBRID_THRESHOLD 100 + #define Y2_HYBRID_THRESHOLD 100 + #define Z_HYBRID_THRESHOLD 3 + #define Z2_HYBRID_THRESHOLD 3 + #define Z3_HYBRID_THRESHOLD 3 + #define E0_HYBRID_THRESHOLD 30 + #define E1_HYBRID_THRESHOLD 30 + #define E2_HYBRID_THRESHOLD 30 + #define E3_HYBRID_THRESHOLD 30 + #define E4_HYBRID_THRESHOLD 30 + #define E5_HYBRID_THRESHOLD 30 + + /** + * TMC2130, TMC2160, TMC2209, TMC2660, TMC5130, and TMC5160 only + * Use StallGuard2 to sense an obstacle and trigger an endstop. + * Connect the stepper driver's DIAG1 pin to the X/Y endstop pin. + * X, Y, and Z homing will always be done in spreadCycle mode. + * + * X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity. + * Higher values make the system LESS sensitive. + * Lower value make the system MORE sensitive. + * Too low values can lead to false positives, while too high values will collide the axis without triggering. + * It is advised to set X/Y/Z_HOME_BUMP_MM to 0. + * M914 X/Y/Z to live tune the setting + */ + //#define SENSORLESS_HOMING // StallGuard capable drivers only + + /** + * Use StallGuard2 to probe the bed with the nozzle. + * + * CAUTION: This could cause damage to machines that use a lead screw or threaded rod + * to move the Z axis. Take extreme care when attempting to enable this feature. + */ + //#define SENSORLESS_PROBING // StallGuard capable drivers only + + #if EITHER(SENSORLESS_HOMING, SENSORLESS_PROBING) + // TMC2209: 0...255. TMC2130: -64...63 + #define X_STALL_SENSITIVITY 8 + #define Y_STALL_SENSITIVITY 8 + //#define Z_STALL_SENSITIVITY 8 + #endif + + /** + * Beta feature! + * Create a 50/50 square wave step pulse optimal for stepper drivers. + */ + //#define SQUARE_WAVE_STEPPING + + /** + * Enable M122 debugging command for TMC stepper drivers. + * M122 S0/1 will enable continous reporting. + */ + //#define TMC_DEBUG + + /** + * You can set your own advanced settings by filling in predefined functions. + * A list of available functions can be found on the library github page + * https://github.com/teemuatlut/TMCStepper + * + * Example: + * #define TMC_ADV() { \ + * stepperX.diag0_temp_prewarn(1); \ + * stepperY.interpolate(0); \ + * } + */ + #define TMC_ADV() { } + +#endif // HAS_TRINAMIC + +// @section L6470 + +/** + * L6470 Stepper Driver options + * + * Arduino-L6470 library (0.7.0 or higher) is required for this stepper driver. + * https://github.com/ameyer/Arduino-L6470 + * + * Requires the following to be defined in your pins_YOUR_BOARD file + * L6470_CHAIN_SCK_PIN + * L6470_CHAIN_MISO_PIN + * L6470_CHAIN_MOSI_PIN + * L6470_CHAIN_SS_PIN + * L6470_RESET_CHAIN_PIN (optional) + */ +#if HAS_DRIVER(L6470) + + //#define L6470_CHITCHAT // Display additional status info + + #if AXIS_DRIVER_TYPE_X(L6470) + #define X_MICROSTEPS 128 // Number of microsteps (VALID: 1, 2, 4, 8, 16, 32, 128) + #define X_OVERCURRENT 2000 // (mA) Current where the driver detects an over current (VALID: 375 x (1 - 16) - 6A max - rounds down) + #define X_STALLCURRENT 1500 // (mA) Current where the driver detects a stall (VALID: 31.25 * (1-128) - 4A max - rounds down) + #define X_MAX_VOLTAGE 127 // 0-255, Maximum effective voltage seen by stepper + #define X_CHAIN_POS 0 // Position in SPI chain, 0=Not in chain, 1=Nearest MOSI + #endif + + #if AXIS_DRIVER_TYPE_X2(L6470) + #define X2_MICROSTEPS 128 + #define X2_OVERCURRENT 2000 + #define X2_STALLCURRENT 1500 + #define X2_MAX_VOLTAGE 127 + #define X2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Y(L6470) + #define Y_MICROSTEPS 128 + #define Y_OVERCURRENT 2000 + #define Y_STALLCURRENT 1500 + #define Y_MAX_VOLTAGE 127 + #define Y_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Y2(L6470) + #define Y2_MICROSTEPS 128 + #define Y2_OVERCURRENT 2000 + #define Y2_STALLCURRENT 1500 + #define Y2_MAX_VOLTAGE 127 + #define Y2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Z(L6470) + #define Z_MICROSTEPS 128 + #define Z_OVERCURRENT 2000 + #define Z_STALLCURRENT 1500 + #define Z_MAX_VOLTAGE 127 + #define Z_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Z2(L6470) + #define Z2_MICROSTEPS 128 + #define Z2_OVERCURRENT 2000 + #define Z2_STALLCURRENT 1500 + #define Z2_MAX_VOLTAGE 127 + #define Z2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Z3(L6470) + #define Z3_MICROSTEPS 128 + #define Z3_OVERCURRENT 2000 + #define Z3_STALLCURRENT 1500 + #define Z3_MAX_VOLTAGE 127 + #define Z3_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E0(L6470) + #define E0_MICROSTEPS 128 + #define E0_OVERCURRENT 2000 + #define E0_STALLCURRENT 1500 + #define E0_MAX_VOLTAGE 127 + #define E0_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E1(L6470) + #define E1_MICROSTEPS 128 + #define E1_OVERCURRENT 2000 + #define E1_STALLCURRENT 1500 + #define E1_MAX_VOLTAGE 127 + #define E1_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E2(L6470) + #define E2_MICROSTEPS 128 + #define E2_OVERCURRENT 2000 + #define E2_STALLCURRENT 1500 + #define E2_MAX_VOLTAGE 127 + #define E2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E3(L6470) + #define E3_MICROSTEPS 128 + #define E3_OVERCURRENT 2000 + #define E3_STALLCURRENT 1500 + #define E3_MAX_VOLTAGE 127 + #define E3_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E4(L6470) + #define E4_MICROSTEPS 128 + #define E4_OVERCURRENT 2000 + #define E4_STALLCURRENT 1500 + #define E4_MAX_VOLTAGE 127 + #define E4_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E5(L6470) + #define E5_MICROSTEPS 128 + #define E5_OVERCURRENT 2000 + #define E5_STALLCURRENT 1500 + #define E5_MAX_VOLTAGE 127 + #define E5_CHAIN_POS 0 + #endif + + /** + * Monitor L6470 drivers for error conditions like over temperature and over current. + * In the case of over temperature Marlin can decrease the drive until the error condition clears. + * Other detected conditions can be used to stop the current print. + * Relevant g-codes: + * M906 - I1/2/3/4/5 Set or get motor drive level using axis codes X, Y, Z, E. Report values if no axis codes given. + * I not present or I0 or I1 - X, Y, Z or E0 + * I2 - X2, Y2, Z2 or E1 + * I3 - Z3 or E3 + * I4 - E4 + * I5 - E5 + * M916 - Increase drive level until get thermal warning + * M917 - Find minimum current thresholds + * M918 - Increase speed until max or error + * M122 S0/1 - Report driver parameters + */ + //#define MONITOR_L6470_DRIVER_STATUS + + #if ENABLED(MONITOR_L6470_DRIVER_STATUS) + #define KVAL_HOLD_STEP_DOWN 1 + //#define L6470_STOP_ON_ERROR + #endif + +#endif // L6470 + +/** + * TWI/I2C BUS + * + * This feature is an EXPERIMENTAL feature so it shall not be used on production + * machines. Enabling this will allow you to send and receive I2C data from slave + * devices on the bus. + * + * ; Example #1 + * ; This macro send the string "Marlin" to the slave device with address 0x63 (99) + * ; It uses multiple M260 commands with one B arg + * M260 A99 ; Target slave address + * M260 B77 ; M + * M260 B97 ; a + * M260 B114 ; r + * M260 B108 ; l + * M260 B105 ; i + * M260 B110 ; n + * M260 S1 ; Send the current buffer + * + * ; Example #2 + * ; Request 6 bytes from slave device with address 0x63 (99) + * M261 A99 B5 + * + * ; Example #3 + * ; Example serial output of a M261 request + * echo:i2c-reply: from:99 bytes:5 data:hello + */ + +// @section i2cbus + +//#define EXPERIMENTAL_I2CBUS +#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave + +// @section extras + +/** + * Photo G-code + * Add the M240 G-code to take a photo. + * The photo can be triggered by a digital pin or a physical movement. + */ +//#define PHOTO_GCODE +#if ENABLED(PHOTO_GCODE) + // A position to move to (and raise Z) before taking the photo + //#define PHOTO_POSITION { X_MAX_POS - 5, Y_MAX_POS, 0 } // { xpos, ypos, zraise } (M240 X Y Z) + //#define PHOTO_DELAY_MS 100 // (ms) Duration to pause before moving back (M240 P) + //#define PHOTO_RETRACT_MM 6.5 // (mm) E retract/recover for the photo move (M240 R S) + + // Canon RC-1 or homebrew digital camera trigger + // Data from: http://www.doc-diy.net/photo/rc-1_hacked/ + //#define PHOTOGRAPH_PIN 23 + + // Canon Hack Development Kit + // http://captain-slow.dk/2014/03/09/3d-printing-timelapses/ + //#define CHDK_PIN 4 + + // Optional second move with delay to trigger the camera shutter + //#define PHOTO_SWITCH_POSITION { X_MAX_POS, Y_MAX_POS } // { xpos, ypos } (M240 I J) + + // Duration to hold the switch or keep CHDK_PIN high + //#define PHOTO_SWITCH_MS 50 // (ms) (M240 D) +#endif + +/** + * Spindle & Laser control + * + * Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and + * to set spindle speed, spindle direction, and laser power. + * + * SuperPid is a router/spindle speed controller used in the CNC milling community. + * Marlin can be used to turn the spindle on and off. It can also be used to set + * the spindle speed from 5,000 to 30,000 RPM. + * + * You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V + * hardware PWM pin for the speed control and a pin for the rotation direction. + * + * See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details. + */ +//#define SPINDLE_FEATURE +//#define LASER_FEATURE +#if EITHER(SPINDLE_FEATURE, LASER_FEATURE) + #define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH + #define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power + #define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower + #define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power + #define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop + + #if ENABLED(SPINDLE_FEATURE) + //#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction + #define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction + #define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed + + /** + * The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power + * + * SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT + * where PWM duty cycle varies from 0 to 255 + * + * set the following for your controller (ALL MUST BE SET) + */ + #define SPEED_POWER_SLOPE 118.4 + #define SPEED_POWER_INTERCEPT 0 + #define SPEED_POWER_MIN 5000 + #define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM + #else + #define SPEED_POWER_SLOPE 0.3922 + #define SPEED_POWER_INTERCEPT 0 + #define SPEED_POWER_MIN 10 + #define SPEED_POWER_MAX 100 // 0-100% + #endif +#endif + +/** + * Coolant Control + * + * Add the M7, M8, and M9 commands to turn mist or flood coolant on and off. + * + * Note: COOLANT_MIST_PIN and/or COOLANT_FLOOD_PIN must also be defined. + */ +//#define COOLANT_CONTROL +#if ENABLED(COOLANT_CONTROL) + #define COOLANT_MIST // Enable if mist coolant is present + #define COOLANT_FLOOD // Enable if flood coolant is present + #define COOLANT_MIST_INVERT false // Set "true" if the on/off function is reversed + #define COOLANT_FLOOD_INVERT false // Set "true" if the on/off function is reversed +#endif + +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define FILWIDTH_ERROR_MARGIN 1.0 // (mm) If a measurement differs too much from nominal width ignore it + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + +/** + * CNC Coordinate Systems + * + * Enables G53 and G54-G59.3 commands to select coordinate systems + * and G92.1 to reset the workspace to native machine space. + */ +//#define CNC_COORDINATE_SYSTEMS + +/** + * Auto-report temperatures with M155 S + */ +#define AUTO_REPORT_TEMPERATURES + +/** + * Include capabilities in M115 output + */ +#define EXTENDED_CAPABILITIES_REPORT + +/** + * Disable all Volumetric extrusion options + */ +//#define NO_VOLUMETRICS + +#if DISABLED(NO_VOLUMETRICS) + /** + * Volumetric extrusion default state + * Activate to make volumetric extrusion the default method, + * with DEFAULT_NOMINAL_FILAMENT_DIA as the default diameter. + * + * M200 D0 to disable, M200 Dn to set a new diameter. + */ + //#define VOLUMETRIC_DEFAULT_ON +#endif + +/** + * Enable this option for a leaner build of Marlin that removes all + * workspace offsets, simplifying coordinate transformations, leveling, etc. + * + * - M206 and M428 are disabled. + * - G92 will revert to its behavior from Marlin 1.0. + */ +//#define NO_WORKSPACE_OFFSETS + +/** + * Set the number of proportional font spaces required to fill up a typical character space. + * This can help to better align the output of commands like `G29 O` Mesh Output. + * + * For clients that use a fixed-width font (like OctoPrint), leave this set to 1.0. + * Otherwise, adjust according to your client and font. + */ +#define PROPORTIONAL_FONT_RATIO 1.0 + +/** + * Spend 28 bytes of SRAM to optimize the GCode parser + */ +#define FASTER_GCODE_PARSER + +/** + * CNC G-code options + * Support CNC-style G-code dialects used by laser cutters, drawing machine cams, etc. + * Note that G0 feedrates should be used with care for 3D printing (if used at all). + * High feedrates may cause ringing and harm print quality. + */ +//#define PAREN_COMMENTS // Support for parentheses-delimited comments +//#define GCODE_MOTION_MODES // Remember the motion mode (G0 G1 G2 G3 G5 G38.X) and apply for X Y Z E F, etc. + +// Enable and set a (default) feedrate for all G0 moves +//#define G0_FEEDRATE 3000 // (mm/m) +#ifdef G0_FEEDRATE + //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode +#endif + +/** + * G-code Macros + * + * Add G-codes M810-M819 to define and run G-code macros. + * Macros are not saved to EEPROM. + */ +//#define GCODE_MACROS +#if ENABLED(GCODE_MACROS) + #define GCODE_MACROS_SLOTS 5 // Up to 10 may be used + #define GCODE_MACROS_SLOT_SIZE 50 // Maximum length of a single macro +#endif + +/** + * User-defined menu items that execute custom GCode + */ +//#define CUSTOM_USER_MENUS +#if ENABLED(CUSTOM_USER_MENUS) + //#define CUSTOM_USER_MENU_TITLE "Custom Commands" + #define USER_SCRIPT_DONE "M117 User Script Done" + #define USER_SCRIPT_AUDIBLE_FEEDBACK + //#define USER_SCRIPT_RETURN // Return to status screen after a script + + #define USER_DESC_1 "Home & UBL Info" + #define USER_GCODE_1 "G28\nG29 W" + + #define USER_DESC_2 "Preheat for " PREHEAT_1_LABEL + #define USER_GCODE_2 "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND) + + #define USER_DESC_3 "Preheat for " PREHEAT_2_LABEL + #define USER_GCODE_3 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND) + + #define USER_DESC_4 "Heat Bed/Home/Level" + #define USER_GCODE_4 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29" + + #define USER_DESC_5 "Home & Info" + #define USER_GCODE_5 "G28\nM503" +#endif + +/** + * Host Action Commands + * + * Define host streamer action commands in compliance with the standard. + * + * See https://reprap.org/wiki/G-code#Action_commands + * Common commands ........ poweroff, pause, paused, resume, resumed, cancel + * G29_RETRY_AND_RECOVER .. probe_rewipe, probe_failed + * + * Some features add reason codes to extend these commands. + * + * Host Prompt Support enables Marlin to use the host for user prompts so + * filament runout and other processes can be managed from the host side. + */ +//#define HOST_ACTION_COMMANDS +#if ENABLED(HOST_ACTION_COMMANDS) + //#define HOST_PROMPT_SUPPORT +#endif + +//=========================================================================== +//====================== I2C Position Encoder Settings ====================== +//=========================================================================== + +/** + * I2C position encoders for closed loop control. + * Developed by Chris Barr at Aus3D. + * + * Wiki: http://wiki.aus3d.com.au/Magnetic_Encoder + * Github: https://github.com/Aus3D/MagneticEncoder + * + * Supplier: http://aus3d.com.au/magnetic-encoder-module + * Alternative Supplier: http://reliabuild3d.com/ + * + * Reliabuild encoders have been modified to improve reliability. + */ + +//#define I2C_POSITION_ENCODERS +#if ENABLED(I2C_POSITION_ENCODERS) + + #define I2CPE_ENCODER_CNT 1 // The number of encoders installed; max of 5 + // encoders supported currently. + + #define I2CPE_ENC_1_ADDR I2CPE_PRESET_ADDR_X // I2C address of the encoder. 30-200. + #define I2CPE_ENC_1_AXIS X_AXIS // Axis the encoder module is installed on. _AXIS. + #define I2CPE_ENC_1_TYPE I2CPE_ENC_TYPE_LINEAR // Type of encoder: I2CPE_ENC_TYPE_LINEAR -or- + // I2CPE_ENC_TYPE_ROTARY. + #define I2CPE_ENC_1_TICKS_UNIT 2048 // 1024 for magnetic strips with 2mm poles; 2048 for + // 1mm poles. For linear encoders this is ticks / mm, + // for rotary encoders this is ticks / revolution. + //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper + // steps per full revolution (motor steps/rev * microstepping) + //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the + // printer will attempt to correct the error; errors + // smaller than this are ignored to minimize effects of + // measurement noise / latency (filter). + + #define I2CPE_ENC_2_ADDR I2CPE_PRESET_ADDR_Y // Same as above, but for encoder 2. + #define I2CPE_ENC_2_AXIS Y_AXIS + #define I2CPE_ENC_2_TYPE I2CPE_ENC_TYPE_LINEAR + #define I2CPE_ENC_2_TICKS_UNIT 2048 + //#define I2CPE_ENC_2_TICKS_REV (16 * 200) + //#define I2CPE_ENC_2_INVERT + #define I2CPE_ENC_2_EC_METHOD I2CPE_ECM_MICROSTEP + #define I2CPE_ENC_2_EC_THRESH 0.10 + + #define I2CPE_ENC_3_ADDR I2CPE_PRESET_ADDR_Z // Encoder 3. Add additional configuration options + #define I2CPE_ENC_3_AXIS Z_AXIS // as above, or use defaults below. + + #define I2CPE_ENC_4_ADDR I2CPE_PRESET_ADDR_E // Encoder 4. + #define I2CPE_ENC_4_AXIS E_AXIS + + #define I2CPE_ENC_5_ADDR 34 // Encoder 5. + #define I2CPE_ENC_5_AXIS E_AXIS + + // Default settings for encoders which are enabled, but without settings configured above. + #define I2CPE_DEF_TYPE I2CPE_ENC_TYPE_LINEAR + #define I2CPE_DEF_ENC_TICKS_UNIT 2048 + #define I2CPE_DEF_TICKS_REV (16 * 200) + #define I2CPE_DEF_EC_METHOD I2CPE_ECM_NONE + #define I2CPE_DEF_EC_THRESH 0.1 + + //#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given + // axis after which the printer will abort. Comment out to + // disable abort behavior. + + #define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault + // for this amount of time (in ms) before the encoder + // is trusted again. + + /** + * Position is checked every time a new command is executed from the buffer but during long moves, + * this setting determines the minimum update time between checks. A value of 100 works well with + * error rolling average when attempting to correct only for skips and not for vibration. + */ + #define I2CPE_MIN_UPD_TIME_MS 4 // (ms) Minimum time between encoder checks. + + // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise. + #define I2CPE_ERR_ROLLING_AVERAGE + +#endif // I2C_POSITION_ENCODERS + +/** + * MAX7219 Debug Matrix + * + * Add support for a low-cost 8x8 LED Matrix based on the Max7219 chip as a realtime status display. + * Requires 3 signal wires. Some useful debug options are included to demonstrate its usage. + */ +//#define MAX7219_DEBUG +#if ENABLED(MAX7219_DEBUG) + #define MAX7219_CLK_PIN 64 + #define MAX7219_DIN_PIN 57 + #define MAX7219_LOAD_PIN 44 + + //#define MAX7219_GCODE // Add the M7219 G-code to control the LED matrix + #define MAX7219_INIT_TEST 2 // Do a test pattern at initialization (Set to 2 for spiral) + #define MAX7219_NUMBER_UNITS 1 // Number of Max7219 units in chain. + #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) + // connector at: right=0 bottom=-90 top=90 left=180 + //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side + + /** + * Sample debug features + * If you add more debug displays, be careful to avoid conflicts! + */ + #define MAX7219_DEBUG_PRINTER_ALIVE // Blink corner LED of 8x8 matrix to show that the firmware is functioning + #define MAX7219_DEBUG_PLANNER_HEAD 3 // Show the planner queue head position on this and the next LED matrix row + #define MAX7219_DEBUG_PLANNER_TAIL 5 // Show the planner queue tail position on this and the next LED matrix row + + #define MAX7219_DEBUG_PLANNER_QUEUE 0 // Show the current planner queue depth on this and the next LED matrix row + // If you experience stuttering, reboots, etc. this option can reveal how + // tweaks made to the configuration are affecting the printer in real-time. +#endif + +/** + * NanoDLP Sync support + * + * Add support for Synchronized Z moves when using with NanoDLP. G0/G1 axis moves will output "Z_move_comp" + * string to enable synchronization with DLP projector exposure. This change will allow to use + * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands + */ +//#define NANODLP_Z_SYNC +#if ENABLED(NANODLP_Z_SYNC) + //#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move. + // Default behavior is limited to Z axis only. +#endif + +/** + * WiFi Support (Espressif ESP32 WiFi) + */ +//#define WIFISUPPORT +#if ENABLED(WIFISUPPORT) + #define WIFI_SSID "Wifi SSID" + #define WIFI_PWD "Wifi Password" + //#define WEBSUPPORT // Start a webserver with auto-discovery + //#define OTASUPPORT // Support over-the-air firmware updates +#endif + +/** + * Prusa Multi-Material Unit v2 + * Enable in Configuration.h + */ +#if ENABLED(PRUSA_MMU2) + + // Serial port used for communication with MMU2. + // For AVR enable the UART port used for the MMU. (e.g., internalSerial) + // For 32-bit boards check your HAL for available serial ports. (e.g., Serial2) + #define INTERNAL_SERIAL_PORT 2 + #define MMU2_SERIAL internalSerial + + // Use hardware reset for MMU if a pin is defined for it + //#define MMU2_RST_PIN 23 + + // Enable if the MMU2 has 12V stepper motors (MMU2 Firmware 1.0.2 and up) + //#define MMU2_MODE_12V + + // G-code to execute when MMU2 F.I.N.D.A. probe detects filament runout + #define MMU2_FILAMENT_RUNOUT_SCRIPT "M600" + + // Add an LCD menu for MMU2 + //#define MMU2_MENUS + #if ENABLED(MMU2_MENUS) + // Settings for filament load / unload from the LCD menu. + // This is for Prusa MK3-style extruders. Customize for your hardware. + #define MMU2_FILAMENTCHANGE_EJECT_FEED 80.0 + #define MMU2_LOAD_TO_NOZZLE_SEQUENCE \ + { 7.2, 562 }, \ + { 14.4, 871 }, \ + { 36.0, 1393 }, \ + { 14.4, 871 }, \ + { 50.0, 198 } + + #define MMU2_RAMMING_SEQUENCE \ + { 1.0, 1000 }, \ + { 1.0, 1500 }, \ + { 2.0, 2000 }, \ + { 1.5, 3000 }, \ + { 2.5, 4000 }, \ + { -15.0, 5000 }, \ + { -14.0, 1200 }, \ + { -6.0, 600 }, \ + { 10.0, 700 }, \ + { -10.0, 400 }, \ + { -50.0, 2000 } + + #endif + + //#define MMU2_DEBUG // Write debug info to serial output + +#endif // PRUSA_MMU2 + +/** + * Advanced Print Counter settings + */ +#if ENABLED(PRINTCOUNTER) + #define SERVICE_WARNING_BUZZES 3 + // Activate up to 3 service interval watchdogs + //#define SERVICE_NAME_1 "Service S" + //#define SERVICE_INTERVAL_1 100 // print hours + //#define SERVICE_NAME_2 "Service L" + //#define SERVICE_INTERVAL_2 200 // print hours + //#define SERVICE_NAME_3 "Service 3" + //#define SERVICE_INTERVAL_3 1 // print hours +#endif + +// @section develop + +/** + * M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins + */ +//#define PINS_DEBUGGING + +// Enable Marlin dev mode which adds some special commands +//#define MARLIN_DEV_MODE diff --git a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h new file mode 100644 index 0000000000..f3c4cea668 --- /dev/null +++ b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h @@ -0,0 +1,2215 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Configuration.h + * + * Basic settings such as: + * + * - Type of electronics + * - Type of temperature sensor + * - Printer geometry + * - Endstop configuration + * - LCD controller + * - Extra features + * + * Advanced settings can be found in Configuration_adv.h + * + */ +#define CONFIGURATION_H_VERSION 020000 + +//=========================================================================== +//============================= Getting Started ============================= +//=========================================================================== + +/** + * Here are some standard links for getting your machine calibrated: + * + * http://reprap.org/wiki/Calibration + * http://youtu.be/wAL9d7FgInk + * http://calculator.josefprusa.cz + * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide + * http://www.thingiverse.com/thing:5573 + * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap + * http://www.thingiverse.com/thing:298812 + */ + +//=========================================================================== +//============================= DELTA Printer =============================== +//=========================================================================== +// For a Delta printer start with one of the configuration files in the +// config/examples/delta directory and customize for your machine. +// + +//=========================================================================== +//============================= SCARA Printer =============================== +//=========================================================================== +// For a SCARA printer start with the configuration files in +// config/examples/SCARA and customize for your machine. +// + +// @section info + +// User-specified version info of this build to display in [Pronterface, etc] terminal window during +// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this +// build by the user have been successfully uploaded into firmware. +#define STRING_CONFIG_H_AUTHOR "(thisiskeithb, Tevo Tornado V2)" // Who made the changes. +#define SHOW_BOOTSCREEN +#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1 +#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2 + +/** + * *** VENDORS PLEASE READ *** + * + * Marlin allows you to add a custom boot image for Graphical LCDs. + * With this option Marlin will first show your custom screen followed + * by the standard Marlin logo with version number and web URL. + * + * We encourage you to take advantage of this new feature and we also + * respectfully request that you retain the unmodified Marlin boot screen. + */ + +// Enable to show the bitmap in Marlin/_Bootscreen.h on startup. +#define SHOW_CUSTOM_BOOTSCREEN + +// Enable to show the bitmap in Marlin/_Statusscreen.h on the status screen. +//#define CUSTOM_STATUS_SCREEN_IMAGE + +// @section machine + +/** + * Select the serial port on the board to use for communication with the host. + * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. + * + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] + */ +#define SERIAL_PORT 0 + +/** + * Select a secondary serial port on the board to use for communication with the host. + * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. + * + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] + */ +//#define SERIAL_PORT_2 -1 + +/** + * This setting determines the communication speed of the printer. + * + * 250000 works in most cases, but you might try a lower speed if + * you commonly experience drop-outs during host printing. + * You may try up to 1000000 to speed up SD file transfer. + * + * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000] + */ +#define BAUDRATE 250000 + +// Enable the Bluetooth serial interface on AT90USB devices +//#define BLUETOOTH + +// Choose the name from boards.h that matches your setup +#ifndef MOTHERBOARD + #define MOTHERBOARD BOARD_MKS_GEN_L +#endif + +// Name displayed in the LCD "Ready" message and Info menu +#define CUSTOM_MACHINE_NAME "Tornado" + +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 +//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" + +// @section extruder + +// This defines the number of extruders +// :[1, 2, 3, 4, 5, 6] +#define EXTRUDERS 1 + +// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc. +#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 + +// For Cyclops or any "multi-extruder" that shares a single nozzle. +//#define SINGLENOZZLE + +/** + * Průša MK2 Single Nozzle Multi-Material Multiplexer, and variants. + * + * This device allows one stepper driver on a control board to drive + * two to eight stepper motors, one at a time, in a manner suitable + * for extruders. + * + * This option only allows the multiplexer to switch on tool-change. + * Additional options to configure custom E moves are pending. + */ +//#define MK2_MULTIPLEXER +#if ENABLED(MK2_MULTIPLEXER) + // Override the default DIO selector pins here, if needed. + // Some pins files may provide defaults for these pins. + //#define E_MUX0_PIN 40 // Always Required + //#define E_MUX1_PIN 42 // Needed for 3 to 8 inputs + //#define E_MUX2_PIN 44 // Needed for 5 to 8 inputs +#endif + +/** + * Prusa Multi-Material Unit v2 + * + * Requires NOZZLE_PARK_FEATURE to park print head in case MMU unit fails. + * Requires EXTRUDERS = 5 + * + * For additional configuration see Configuration_adv.h + */ +//#define PRUSA_MMU2 + +// A dual extruder that uses a single stepper motor +//#define SWITCHING_EXTRUDER +#if ENABLED(SWITCHING_EXTRUDER) + #define SWITCHING_EXTRUDER_SERVO_NR 0 + #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3] + #if EXTRUDERS > 3 + #define SWITCHING_EXTRUDER_E23_SERVO_NR 1 + #endif +#endif + +// A dual-nozzle that uses a servomotor to raise/lower one (or both) of the nozzles +//#define SWITCHING_NOZZLE +#if ENABLED(SWITCHING_NOZZLE) + #define SWITCHING_NOZZLE_SERVO_NR 0 + //#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second + #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo) +#endif + +/** + * Two separate X-carriages with extruders that connect to a moving part + * via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN. + */ +//#define PARKING_EXTRUDER + +/** + * Two separate X-carriages with extruders that connect to a moving part + * via a magnetic docking mechanism using movements and no solenoid + * + * project : https://www.thingiverse.com/thing:3080893 + * movements : https://youtu.be/0xCEiG9VS3k + * https://youtu.be/Bqbcs0CU2FE + */ +//#define MAGNETIC_PARKING_EXTRUDER + +#if EITHER(PARKING_EXTRUDER, MAGNETIC_PARKING_EXTRUDER) + + #define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders + #define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder + //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381 + + #if ENABLED(PARKING_EXTRUDER) + + #define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage + #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil + #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined. + //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381 + + #elif ENABLED(MAGNETIC_PARKING_EXTRUDER) + + #define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point + #define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple + #define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point + #define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling + + #endif + +#endif + +/** + * Switching Toolhead + * + * Support for swappable and dockable toolheads, such as + * the E3D Tool Changer. Toolheads are locked with a servo. + */ +//#define SWITCHING_TOOLHEAD + +/** + * Magnetic Switching Toolhead + * + * Support swappable and dockable toolheads with a magnetic + * docking mechanism using movement and no servo. + */ +//#define MAGNETIC_SWITCHING_TOOLHEAD + +/** + * Electromagnetic Switching Toolhead + * + * Parking for CoreXY / HBot kinematics. + * Toolheads are parked at one edge and held with an electromagnet. + * Supports more than 2 Toolheads. See https://youtu.be/JolbsAKTKf4 + */ +//#define ELECTROMAGNETIC_SWITCHING_TOOLHEAD + +#if ANY(SWITCHING_TOOLHEAD, MAGNETIC_SWITCHING_TOOLHEAD, ELECTROMAGNETIC_SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_Y_POS 235 // (mm) Y position of the toolhead dock + #define SWITCHING_TOOLHEAD_Y_SECURITY 10 // (mm) Security distance Y axis + #define SWITCHING_TOOLHEAD_Y_CLEAR 60 // (mm) Minimum distance from dock for unobstructed X axis + #define SWITCHING_TOOLHEAD_X_POS { 215, 0 } // (mm) X positions for parking the extruders + #if ENABLED(SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_SERVO_NR 2 // Index of the servo connector + #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock + #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif + #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching + #endif +#endif + +/** + * "Mixing Extruder" + * - Adds G-codes M163 and M164 to set and "commit" the current mix factors. + * - Extends the stepping routines to move multiple steppers in proportion to the mix. + * - Optional support for Repetier Firmware's 'M164 S' supporting virtual tools. + * - This implementation supports up to two mixing extruders. + * - Enable DIRECT_MIXING_IN_G1 for M165 and mixing in G1 (from Pia Taubert's reference implementation). + */ +//#define MIXING_EXTRUDER +#if ENABLED(MIXING_EXTRUDER) + #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder + #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164 + //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands + //#define GRADIENT_MIX // Support for gradient mixing with M166 and LCD + #if ENABLED(GRADIENT_MIX) + //#define GRADIENT_VTOOL // Add M166 T to use a V-tool index as a Gradient alias + #endif +#endif + +// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). +// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). +// For the other hotends it is their distance from the extruder 0 hotend. +//#define HOTEND_OFFSET_X { 0.0, 20.00 } // (mm) relative X-offset for each nozzle +//#define HOTEND_OFFSET_Y { 0.0, 5.00 } // (mm) relative Y-offset for each nozzle +//#define HOTEND_OFFSET_Z { 0.0, 0.00 } // (mm) relative Z-offset for each nozzle + +// @section machine + +/** + * Power Supply Control + * + * Enable and connect the power supply to the PS_ON_PIN. + * Specify whether the power supply is active HIGH or active LOW. + */ +//#define PSU_CONTROL +//#define PSU_NAME "Power Supply" + +#if ENABLED(PSU_CONTROL) + #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2) + + //#define PS_DEFAULT_OFF // Keep power off until enabled directly with M80 + + //#define AUTO_POWER_CONTROL // Enable automatic control of the PS_ON pin + #if ENABLED(AUTO_POWER_CONTROL) + #define AUTO_POWER_FANS // Turn on PSU if fans need power + #define AUTO_POWER_E_FANS + #define AUTO_POWER_CONTROLLERFAN + #define AUTO_POWER_CHAMBER_FAN + //#define AUTO_POWER_E_TEMP 50 // (°C) Turn on PSU over this temperature + //#define AUTO_POWER_CHAMBER_TEMP 30 // (°C) Turn on PSU over this temperature + #define POWER_TIMEOUT 30 + #endif +#endif + +// @section temperature + +//=========================================================================== +//============================= Thermal Settings ============================ +//=========================================================================== + +/** + * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table + * + * Temperature sensors available: + * + * -4 : thermocouple with AD8495 + * -3 : thermocouple with MAX31855 (only for sensor 0) + * -2 : thermocouple with MAX6675 (only for sensor 0) + * -1 : thermocouple with AD595 + * 0 : not used + * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 3 : Mendel-parts thermistor (4.7k pullup) + * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! + * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) + * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) + * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) + * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) + * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) + * 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) + * 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) + * 10 : 100k RS thermistor 198-961 (4.7k pullup) + * 11 : 100k beta 3950 1% thermistor (4.7k pullup) + * 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) + * 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" + * 15 : 100k thermistor calibration for JGAurora A5 hotend + * 18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327 + * 20 : the PT100 circuit found in the Ultimainboard V2.x + * 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 + * 61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup + * 66 : 4.7M High Temperature thermistor from Dyze Design + * 67 : 450C thermistor from SliceEngineering + * 70 : the 100K thermistor found in the bq Hephestos 2 + * 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor + * + * 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k. + * (but gives greater accuracy and more stable PID) + * 51 : 100k thermistor - EPCOS (1k pullup) + * 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup) + * 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) + * + * 1047 : Pt1000 with 4k7 pullup + * 1010 : Pt1000 with 1k pullup (non standard) + * 147 : Pt100 with 4k7 pullup + * 110 : Pt100 with 1k pullup (non standard) + * + * 1000 : Custom - Specify parameters in Configuration_adv.h + * + * Use these for Testing or Development purposes. NEVER for production machine. + * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. + * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. + * + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + */ +#define TEMP_SENSOR_0 1 +#define TEMP_SENSOR_1 0 +#define TEMP_SENSOR_2 0 +#define TEMP_SENSOR_3 0 +#define TEMP_SENSOR_4 0 +#define TEMP_SENSOR_5 0 +#define TEMP_SENSOR_BED 1 +#define TEMP_SENSOR_CHAMBER 0 + +// Dummy thermistor constant temperature readings, for use with 998 and 999 +#define DUMMY_THERMISTOR_998_VALUE 25 +#define DUMMY_THERMISTOR_999_VALUE 100 + +// Use temp sensor 1 as a redundant sensor with sensor 0. If the readings +// from the two sensors differ too much the print will be aborted. +//#define TEMP_SENSOR_1_AS_REDUNDANT +#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 + +#define TEMP_RESIDENCY_TIME 5 // (seconds) Time to wait for hotend to "settle" in M109 +#define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer +#define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target + +#define TEMP_BED_RESIDENCY_TIME 5 // (seconds) Time to wait for bed to "settle" in M190 +#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer +#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target + +// Below this temperature the heater will be switched off +// because it probably indicates a broken thermistor wire. +#define HEATER_0_MINTEMP 5 +#define HEATER_1_MINTEMP 5 +#define HEATER_2_MINTEMP 5 +#define HEATER_3_MINTEMP 5 +#define HEATER_4_MINTEMP 5 +#define HEATER_5_MINTEMP 5 +#define BED_MINTEMP 5 + +// Above this temperature the heater will be switched off. +// This can protect components from overheating, but NOT from shorts and failures. +// (Use MINTEMP for thermistor short/failure protection.) +#define HEATER_0_MAXTEMP 285 +#define HEATER_1_MAXTEMP 275 +#define HEATER_2_MAXTEMP 275 +#define HEATER_3_MAXTEMP 275 +#define HEATER_4_MAXTEMP 275 +#define HEATER_5_MAXTEMP 275 +#define BED_MAXTEMP 150 + +//=========================================================================== +//============================= PID Settings ================================ +//=========================================================================== +// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning + +// Comment the following line to disable PID and enable bang-bang. +#define PIDTEMP +#define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current +#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current +#define PID_K1 0.95 // Smoothing factor within any PID loop +#if ENABLED(PIDTEMP) + #define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM) + #define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM) + //#define PID_DEBUG // Sends debug data to the serial port. + //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX + //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay + //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] + #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature + // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. + + // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it + + // Tevo Tornado V2 + #define DEFAULT_Kp 20.37 + #define DEFAULT_Ki 1.50 + #define DEFAULT_Kd 69.26 + + // Ultimaker + //#define DEFAULT_Kp 22.2 + //#define DEFAULT_Ki 1.08 + //#define DEFAULT_Kd 114 + + // MakerGear + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 + + // Mendel Parts V9 on 12V + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 + +#endif // PIDTEMP + +//=========================================================================== +//====================== PID > Bed Temperature Control ====================== +//=========================================================================== + +/** + * PID Bed Heating + * + * If this option is enabled set PID constants below. + * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis. + * + * The PID frequency will be the same as the extruder PWM. + * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz, + * which is fine for driving a square wave into a resistive load and does not significantly + * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W + * heater. If your configuration is significantly different than this and you don't understand + * the issues involved, don't use bed PID until someone else verifies that your hardware works. + */ +#define PIDTEMPBED + +//#define BED_LIMIT_SWITCHING + +/** + * Max Bed Power + * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis). + * When set to any value below 255, enables a form of PWM to the bed that acts like a divider + * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED) + */ +#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current + +#if ENABLED(PIDTEMPBED) + //#define MIN_BED_POWER 0 + //#define PID_BED_DEBUG // Sends debug data to the serial port. + + //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) + //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) + #define DEFAULT_bedKp 128.82 + #define DEFAULT_bedKi 16.91 + #define DEFAULT_bedKd 245.36 + + //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) + //from pidautotune + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 + + // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. +#endif // PIDTEMPBED + +// @section extruder + +/** + * Prevent extrusion if the temperature is below EXTRUDE_MINTEMP. + * Add M302 to set the minimum extrusion temperature and/or turn + * cold extrusion prevention on and off. + * + * *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! *** + */ +#define PREVENT_COLD_EXTRUSION +#define EXTRUDE_MINTEMP 170 + +/** + * Prevent a single extrusion longer than EXTRUDE_MAXLENGTH. + * Note: For Bowden Extruders make this large enough to allow load/unload. + */ +#define PREVENT_LENGTHY_EXTRUDE +#define EXTRUDE_MAXLENGTH 600 + +//=========================================================================== +//======================== Thermal Runaway Protection ======================= +//=========================================================================== + +/** + * Thermal Protection provides additional protection to your printer from damage + * and fire. Marlin always includes safe min and max temperature ranges which + * protect against a broken or disconnected thermistor wire. + * + * The issue: If a thermistor falls out, it will report the much lower + * temperature of the air in the room, and the the firmware will keep + * the heater on. + * + * If you get "Thermal Runaway" or "Heating failed" errors the + * details can be tuned in Configuration_adv.h + */ + +#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders +#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed +#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber + +//=========================================================================== +//============================= Mechanical Settings ========================= +//=========================================================================== + +// @section machine + +// Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics +// either in the usual order or reversed +//#define COREXY +//#define COREXZ +//#define COREYZ +//#define COREYX +//#define COREZX +//#define COREZY + +//=========================================================================== +//============================== Endstop Settings =========================== +//=========================================================================== + +// @section homing + +// Specify here all the endstop connectors that are connected to any endstop or probe. +// Almost all printers will be using one per axis. Probes will use one or more of the +// extra connectors. Leave undefined any used for non-endstop and non-probe purposes. +#define USE_XMIN_PLUG +#define USE_YMIN_PLUG +#define USE_ZMIN_PLUG +//#define USE_XMAX_PLUG +//#define USE_YMAX_PLUG +//#define USE_ZMAX_PLUG + +// Enable pullup for all endstops to prevent a floating state +#define ENDSTOPPULLUPS +#if DISABLED(ENDSTOPPULLUPS) + // Disable ENDSTOPPULLUPS to set pullups individually + //#define ENDSTOPPULLUP_XMAX + //#define ENDSTOPPULLUP_YMAX + //#define ENDSTOPPULLUP_ZMAX + //#define ENDSTOPPULLUP_XMIN + //#define ENDSTOPPULLUP_YMIN + //#define ENDSTOPPULLUP_ZMIN + //#define ENDSTOPPULLUP_ZMIN_PROBE +#endif + +// Enable pulldown for all endstops to prevent a floating state +//#define ENDSTOPPULLDOWNS +#if DISABLED(ENDSTOPPULLDOWNS) + // Disable ENDSTOPPULLDOWNS to set pulldowns individually + //#define ENDSTOPPULLDOWN_XMAX + //#define ENDSTOPPULLDOWN_YMAX + //#define ENDSTOPPULLDOWN_ZMAX + //#define ENDSTOPPULLDOWN_XMIN + //#define ENDSTOPPULLDOWN_YMIN + //#define ENDSTOPPULLDOWN_ZMIN + //#define ENDSTOPPULLDOWN_ZMIN_PROBE +#endif + +// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup). +#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop. +#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop. +#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop. +#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe. + +/** + * Stepper Drivers + * + * These settings allow Marlin to tune stepper driver timing and enable advanced options for + * stepper drivers that support them. You may also override timing options in Configuration_adv.h. + * + * A4988 is assumed for unspecified drivers. + * + * Options: A4988, A5984, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100, + * TMC2130, TMC2130_STANDALONE, TMC2160, TMC2160_STANDALONE, + * TMC2208, TMC2208_STANDALONE, TMC2209, TMC2209_STANDALONE, + * TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE, + * TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE + * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE'] + */ +#define X_DRIVER_TYPE A4988 +#define Y_DRIVER_TYPE A4988 +#define Z_DRIVER_TYPE A4988 +//#define X2_DRIVER_TYPE A4988 +//#define Y2_DRIVER_TYPE A4988 +//#define Z2_DRIVER_TYPE A4988 +//#define Z3_DRIVER_TYPE A4988 +#define E0_DRIVER_TYPE A4988 +//#define E1_DRIVER_TYPE A4988 +//#define E2_DRIVER_TYPE A4988 +//#define E3_DRIVER_TYPE A4988 +//#define E4_DRIVER_TYPE A4988 +//#define E5_DRIVER_TYPE A4988 + +// Enable this feature if all enabled endstop pins are interrupt-capable. +// This will remove the need to poll the interrupt pins, saving many CPU cycles. +//#define ENDSTOP_INTERRUPTS_FEATURE + +/** + * Endstop Noise Threshold + * + * Enable if your probe or endstops falsely trigger due to noise. + * + * - Higher values may affect repeatability or accuracy of some bed probes. + * - To fix noise install a 100nF ceramic capacitor inline with the switch. + * - This feature is not required for common micro-switches mounted on PCBs + * based on the Makerbot design, which already have the 100nF capacitor. + * + * :[2,3,4,5,6,7] + */ +//#define ENDSTOP_NOISE_THRESHOLD 2 + +//============================================================================= +//============================== Movement Settings ============================ +//============================================================================= +// @section motion + +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * With this option each E stepper can have its own factors for the + * following movement settings. If fewer factors are given than the + * total number of extruders, the last value applies to the rest. + */ +//#define DISTINCT_E_FACTORS + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] + */ +#define DEFAULT_AXIS_STEPS_PER_UNIT { 79.765, 79.765, 399.2901, 400 } + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] + */ +#define DEFAULT_MAX_FEEDRATE { 250, 250, 30, 55 } + +/** + * Default Max Acceleration (change/s) change = mm/s + * (Maximum start speed for accelerated moves) + * Override with M201 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] + */ +#define DEFAULT_MAX_ACCELERATION { 2000, 2000, 120, 10000 } + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 1000 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 10000 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 1500 // X, Y, Z acceleration for travel (non printing) moves + +/** + * Junction Deviation + * + * Use Junction Deviation instead of traditional Jerk Limiting + * + * See: + * https://reprap.org/forum/read.php?1,739819 + * http://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html + */ +//#define JUNCTION_DEVIATION +#if ENABLED(JUNCTION_DEVIATION) + #define JUNCTION_DEVIATION_MM 0.02 // (mm) Distance from real junction edge +#endif + +/** + * Default Jerk (mm/s) + * Override with M205 X Y Z E + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#if DISABLED(JUNCTION_DEVIATION) + #define DEFAULT_XJERK 8.0 + #define DEFAULT_YJERK 8.0 + #define DEFAULT_ZJERK 0.4 +#endif + +#define DEFAULT_EJERK 5.0 // May be used by Linear Advance + +/** + * S-Curve Acceleration + * + * This option eliminates vibration during printing by fitting a Bézier + * curve to move acceleration, producing much smoother direction changes. + * + * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained + */ +#define S_CURVE_ACCELERATION + +//=========================================================================== +//============================= Z Probe Options ============================= +//=========================================================================== +// @section probes + +// +// See http://marlinfw.org/docs/configuration/probes.html +// + +/** + * Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + * + * Enable this option for a probe connected to the Z Min endstop pin. + */ +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +/** + * Z_MIN_PROBE_PIN + * + * Define this pin if the probe is not connected to Z_MIN_PIN. + * If not defined the default pin for the selected MOTHERBOARD + * will be used. Most of the time the default is what you want. + * + * - The simplest option is to use a free endstop connector. + * - Use 5V for powered (usually inductive) sensors. + * + * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin: + * - For simple switches connect... + * - normally-closed switches to GND and D32. + * - normally-open switches to 5V and D32. + * + */ +//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default + +/** + * Probe Type + * + * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. + * Activate one of these to use Auto Bed Leveling below. + */ + +/** + * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe. + * Use G29 repeatedly, adjusting the Z height at each point with movement commands + * or (with LCD_BED_LEVELING) the LCD controller. + */ +//#define PROBE_MANUALLY +//#define MANUAL_PROBE_START_Z 0.2 + +/** + * A Fix-Mounted Probe either doesn't deploy or needs manual deployment. + * (e.g., an inductive probe or a nozzle-based probe-switch.) + */ +//#define FIX_MOUNTED_PROBE + +/** + * Z Servo Probe, such as an endstop switch on a rotating arm. + */ +//#define Z_PROBE_SERVO_NR 0 // Defaults to SERVO 0 connector. +//#define Z_SERVO_ANGLES { 70, 0 } // Z Servo Deploy and Stow angles + +/** + * The BLTouch probe uses a Hall effect sensor and emulates a servo. + */ +//#define BLTOUCH + +/** + * Touch-MI Probe by hotends.fr + * + * This probe is deployed and activated by moving the X-axis to a magnet at the edge of the bed. + * By default, the magnet is assumed to be on the left and activated by a home. If the magnet is + * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position. + * + * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING, + * and a minimum Z_HOMING_HEIGHT of 10. + */ +//#define TOUCH_MI_PROBE +#if ENABLED(TOUCH_MI_PROBE) + #define TOUCH_MI_RETRACT_Z 0.5 // Height at which the probe retracts + //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2) // For a magnet on the right side of the bed + //#define TOUCH_MI_MANUAL_DEPLOY // For manual deploy (LCD menu) +#endif + +// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) +//#define SOLENOID_PROBE + +// A sled-mounted probe like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +// A probe deployed by moving the x-axis, such as the Wilson II's rack-and-pinion probe designed by Marty Rice. +//#define RACK_AND_PINION_PROBE +#if ENABLED(RACK_AND_PINION_PROBE) + #define Z_PROBE_DEPLOY_X X_MIN_POS + #define Z_PROBE_RETRACT_X X_MAX_POS +#endif + +// +// For Z_PROBE_ALLEN_KEY see the Delta example configurations. +// + +/** + * Z Probe to nozzle (X,Y) offset, relative to (0, 0). + * X and Y offsets must be integers. + * + * In the following example the X and Y offsets are both positive: + * #define X_PROBE_OFFSET_FROM_EXTRUDER 10 + * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 + * + * +-- BACK ---+ + * | | + * L | (+) P | R <-- probe (20,20) + * E | | I + * F | (-) N (+) | G <-- nozzle (10,10) + * T | | H + * | (-) | T + * | | + * O-- FRONT --+ + * (0,0) + */ +#define X_PROBE_OFFSET_FROM_EXTRUDER -45 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER -12 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER -2.77 // Z offset: -below +above [the nozzle] + +// Certain types of probes need to stay away from edges +#define MIN_PROBE_EDGE 10 + +// X and Y axis travel speed (mm/m) between probes +#define XY_PROBE_SPEED 8000 + +// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2) +#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z + +// Feedrate (mm/m) for the "accurate" probe of each point +#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) + +/** + * Multiple Probing + * + * You may get improved results by probing 2 or more times. + * With EXTRA_PROBING the more atypical reading(s) will be disregarded. + * + * A total of 2 does fast/slow probes with a weighted average. + * A total of 3 or more adds more slow probes, taking the average. + */ +//#define MULTIPLE_PROBING 2 +//#define EXTRA_PROBING 1 + +/** + * Z probes require clearance when deploying, stowing, and moving between + * probe points to avoid hitting the bed and other hardware. + * Servo-mounted probes require extra space for the arm to rotate. + * Inductive probes need space to keep from triggering early. + * + * Use these settings to specify the distance (mm) to raise the probe (or + * lower the bed). The values set here apply over and above any (negative) + * probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD. + * Only integer values >= 1 are valid here. + * + * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle. + * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle. + */ +#define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow +#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points +#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes +//#define Z_AFTER_PROBING 5 // Z position after probing is done + +#define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping + +// For M851 give a range for adjusting the Z probe offset +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + +// Enable the M48 repeatability test to test probe accuracy +//#define Z_MIN_PROBE_REPEATABILITY_TEST + +// Before deploy/stow pause for user confirmation +//#define PAUSE_BEFORE_DEPLOY_STOW +#if ENABLED(PAUSE_BEFORE_DEPLOY_STOW) + //#define PAUSE_PROBE_DEPLOY_WHEN_TRIGGERED // For Manual Deploy Allenkey Probe +#endif + +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + +// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 +// :{ 0:'Low', 1:'High' } +#define X_ENABLE_ON 0 +#define Y_ENABLE_ON 0 +#define Z_ENABLE_ON 0 +#define E_ENABLE_ON 0 // For all extruders + +// Disables axis stepper immediately when it's not being used. +// WARNING: When motors turn off there is a chance of losing position accuracy! +#define DISABLE_X false +#define DISABLE_Y false +#define DISABLE_Z false + +// Warn on display about possibly reduced accuracy +//#define DISABLE_REDUCED_ACCURACY_WARNING + +// @section extruder + +#define DISABLE_E false // For all extruders +#define DISABLE_INACTIVE_EXTRUDER // Keep only the active extruder enabled + +// @section machine + +// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way. +#define INVERT_X_DIR false +#define INVERT_Y_DIR false +#define INVERT_Z_DIR true + +// @section extruder + +// For direct drive extruder v9 set to true, for geared extruder set to false. +#define INVERT_E0_DIR true +#define INVERT_E1_DIR false +#define INVERT_E2_DIR false +#define INVERT_E3_DIR false +#define INVERT_E4_DIR false +#define INVERT_E5_DIR false + +// @section homing + +//#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed + +//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off. + +//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ... + // Be sure you have this distance over your Z_MAX_POS in case. + +// Direction of endstops when homing; 1=MAX, -1=MIN +// :[-1,1] +#define X_HOME_DIR -1 +#define Y_HOME_DIR -1 +#define Z_HOME_DIR -1 + +// @section machine + +// The size of the print bed +#define X_BED_SIZE 320 +#define Y_BED_SIZE 300 + +// Travel limits (mm) after homing, corresponding to endstop positions. +#define X_MIN_POS 0 +#define Y_MIN_POS 0 +#define Z_MIN_POS 0 +#define X_MAX_POS X_BED_SIZE +#define Y_MAX_POS Y_BED_SIZE +#define Z_MAX_POS 400 + +/** + * Software Endstops + * + * - Prevent moves outside the set machine bounds. + * - Individual axes can be disabled, if desired. + * - X and Y only apply to Cartesian robots. + * - Use 'M211' to set software endstops on/off or report current state + */ + +// Min software endstops constrain movement within minimum coordinate bounds +#define MIN_SOFTWARE_ENDSTOPS +#if ENABLED(MIN_SOFTWARE_ENDSTOPS) + #define MIN_SOFTWARE_ENDSTOP_X + #define MIN_SOFTWARE_ENDSTOP_Y + #define MIN_SOFTWARE_ENDSTOP_Z +#endif + +// Max software endstops constrain movement within maximum coordinate bounds +#define MAX_SOFTWARE_ENDSTOPS +#if ENABLED(MAX_SOFTWARE_ENDSTOPS) + #define MAX_SOFTWARE_ENDSTOP_X + #define MAX_SOFTWARE_ENDSTOP_Y + #define MAX_SOFTWARE_ENDSTOP_Z +#endif + +#if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS) + //#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD +#endif + +/** + * Filament Runout Sensors + * Mechanical or opto endstops are used to check for the presence of filament. + * + * RAMPS-based boards use SERVO3_PIN for the first runout sensor. + * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc. + * By default the firmware assumes HIGH=FILAMENT PRESENT. + */ +//#define FILAMENT_RUNOUT_SENSOR +#if ENABLED(FILAMENT_RUNOUT_SENSOR) + #define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each. + #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor. + #define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins. + //#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins. + + // Set one or more commands to execute on filament runout. + // (After 'M412 H' Marlin will ask the host to handle the process.) + #define FILAMENT_RUNOUT_SCRIPT "M600" + + // After a runout is detected, continue printing this length of filament + // before executing the runout script. Useful for a sensor at the end of + // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead. + //#define FILAMENT_RUNOUT_DISTANCE_MM 25 + + #ifdef FILAMENT_RUNOUT_DISTANCE_MM + // Enable this option to use an encoder disc that toggles the runout pin + // as the filament moves. (Be sure to set FILAMENT_RUNOUT_DISTANCE_MM + // large enough to avoid false positives.) + //#define FILAMENT_MOTION_SENSOR + #endif +#endif + +//=========================================================================== +//=============================== Bed Leveling ============================== +//=========================================================================== +// @section calibrate + +/** + * Choose one of the options below to enable G29 Bed Leveling. The parameters + * and behavior of G29 will change depending on your selection. + * + * If using a Probe for Z Homing, enable Z_SAFE_HOMING also! + * + * - AUTO_BED_LEVELING_3POINT + * Probe 3 arbitrary points on the bed (that aren't collinear) + * You specify the XY coordinates of all 3 points. + * The result is a single tilted plane. Best for a flat bed. + * + * - AUTO_BED_LEVELING_LINEAR + * Probe several points in a grid. + * You specify the rectangle and the density of sample points. + * The result is a single tilted plane. Best for a flat bed. + * + * - AUTO_BED_LEVELING_BILINEAR + * Probe several points in a grid. + * You specify the rectangle and the density of sample points. + * The result is a mesh, best for large or uneven beds. + * + * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling) + * A comprehensive bed leveling system combining the features and benefits + * of other systems. UBL also includes integrated Mesh Generation, Mesh + * Validation and Mesh Editing systems. + * + * - MESH_BED_LEVELING + * Probe a grid manually + * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.) + * For machines without a probe, Mesh Bed Leveling provides a method to perform + * leveling in steps so you can manually adjust the Z height at each grid-point. + * With an LCD controller the process is guided step-by-step. + */ +//#define AUTO_BED_LEVELING_3POINT +//#define AUTO_BED_LEVELING_LINEAR +//#define AUTO_BED_LEVELING_BILINEAR +//#define AUTO_BED_LEVELING_UBL +#define MESH_BED_LEVELING + +/** + * Normally G28 leaves leveling disabled on completion. Enable + * this option to have G28 restore the prior leveling state. + */ +#define RESTORE_LEVELING_AFTER_G28 + +/** + * Enable detailed logging of G28, G29, M48, etc. + * Turn on with the command 'M111 S32'. + * NOTE: Requires a lot of PROGMEM! + */ +//#define DEBUG_LEVELING_FEATURE + +#if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_BILINEAR, AUTO_BED_LEVELING_UBL) + // Gradually reduce leveling correction until a set height is reached, + // at which point movement will be level to the machine's XY plane. + // The height can be set with M420 Z + #define ENABLE_LEVELING_FADE_HEIGHT + + // For Cartesian machines, instead of dividing moves on mesh boundaries, + // split up moves into short segments like a Delta. This follows the + // contours of the bed more closely than edge-to-edge straight moves. + #define SEGMENT_LEVELED_MOVES + #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one) + + /** + * Enable the G26 Mesh Validation Pattern tool. + */ + #define G26_MESH_VALIDATION + #if ENABLED(G26_MESH_VALIDATION) + #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle. + #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool. + #define MESH_TEST_HOTEND_TEMP 205 // (°C) Default nozzle temperature for the G26 Mesh Validation Tool. + #define MESH_TEST_BED_TEMP 60 // (°C) Default bed temperature for the G26 Mesh Validation Tool. + #define G26_XY_FEEDRATE 20 // (mm/s) Feedrate for XY Moves for the G26 Mesh Validation Tool. + #endif + +#endif + +#if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR) + + // Set the number of grid points per dimension. + #define GRID_MAX_POINTS_X 3 + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + // Set the boundaries for probing (where the probe can reach). + //#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE + //#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE)) + //#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE + //#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE)) + + // Probe along the Y axis, advancing X after each column + //#define PROBE_Y_FIRST + + #if ENABLED(AUTO_BED_LEVELING_BILINEAR) + + // Beyond the probed grid, continue the implied tilt? + // Default is to maintain the height of the nearest edge. + //#define EXTRAPOLATE_BEYOND_GRID + + // + // Experimental Subdivision of the grid by Catmull-Rom method. + // Synthesizes intermediate points to produce a more detailed mesh. + // + //#define ABL_BILINEAR_SUBDIVISION + #if ENABLED(ABL_BILINEAR_SUBDIVISION) + // Number of subdivisions between probe points + #define BILINEAR_SUBDIVISIONS 3 + #endif + + #endif + +#elif ENABLED(AUTO_BED_LEVELING_UBL) + + //=========================================================================== + //========================= Unified Bed Leveling ============================ + //=========================================================================== + + //#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh + + #define MESH_INSET 1 // Set Mesh bounds as an inset region of the bed + #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited. + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + #define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle + #define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500 + + //#define UBL_Z_RAISE_WHEN_OFF_MESH 2.5 // When the nozzle is off the mesh, this value is used + // as the Z-Height correction value. + +#elif ENABLED(MESH_BED_LEVELING) + + //=========================================================================== + //=================================== Mesh ================================== + //=========================================================================== + + #define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed + #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited. + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS + +#endif // BED_LEVELING + +/** + * Points to probe for all 3-point Leveling procedures. + * Override if the automatically selected points are inadequate. + */ +#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL) + //#define PROBE_PT_1_X 15 + //#define PROBE_PT_1_Y 180 + //#define PROBE_PT_2_X 15 + //#define PROBE_PT_2_Y 20 + //#define PROBE_PT_3_X 170 + //#define PROBE_PT_3_Y 20 +#endif + +/** + * Add a bed leveling sub-menu for ABL or MBL. + * Include a guided procedure if manual probing is enabled. + */ +#define LCD_BED_LEVELING + +#if ENABLED(LCD_BED_LEVELING) + #define MESH_EDIT_Z_STEP 0.025 // (mm) Step size while manually probing Z axis. + #define LCD_PROBE_Z_RANGE 4 // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment + //#define MESH_EDIT_MENU // Add a menu to edit mesh points +#endif + +// Add a menu item to move between bed corners for manual bed adjustment +#define LEVEL_BED_CORNERS + +#if ENABLED(LEVEL_BED_CORNERS) + #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner +#endif + +/** + * Commands to execute at the end of G29 probing. + * Useful to retract or move the Z probe out of the way. + */ +//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" + + +// @section homing + +// The center of the bed is at (X=0, Y=0) +//#define BED_CENTER_AT_0_0 + +// Manually set the home position. Leave these undefined for automatic settings. +// For DELTA this is the top-center of the Cartesian print volume. +//#define MANUAL_X_HOME_POS 0 +//#define MANUAL_Y_HOME_POS 0 +//#define MANUAL_Z_HOME_POS 0 + +// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area. +// +// With this feature enabled: +// +// - Allow Z homing only after X and Y homing AND stepper drivers still enabled. +// - If stepper drivers time out, it will need X and Y homing again before Z homing. +// - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28). +// - Prevent Z homing when the Z probe is outside bed area. +// +//#define Z_SAFE_HOMING + +#if ENABLED(Z_SAFE_HOMING) + #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing when homing all axes (G28). + #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2) // Y point for Z homing when homing all axes (G28). +#endif + +// Homing speeds (mm/m) +#define HOMING_FEEDRATE_XY (50*60) +#define HOMING_FEEDRATE_Z (4*60) + +// Validate that endstops are triggered on homing moves +#define VALIDATE_HOMING_ENDSTOPS + +// @section calibrate + +/** + * Bed Skew Compensation + * + * This feature corrects for misalignment in the XYZ axes. + * + * Take the following steps to get the bed skew in the XY plane: + * 1. Print a test square (e.g., https://www.thingiverse.com/thing:2563185) + * 2. For XY_DIAG_AC measure the diagonal A to C + * 3. For XY_DIAG_BD measure the diagonal B to D + * 4. For XY_SIDE_AD measure the edge A to D + * + * Marlin automatically computes skew factors from these measurements. + * Skew factors may also be computed and set manually: + * + * - Compute AB : SQRT(2*AC*AC+2*BD*BD-4*AD*AD)/2 + * - XY_SKEW_FACTOR : TAN(PI/2-ACOS((AC*AC-AB*AB-AD*AD)/(2*AB*AD))) + * + * If desired, follow the same procedure for XZ and YZ. + * Use these diagrams for reference: + * + * Y Z Z + * ^ B-------C ^ B-------C ^ B-------C + * | / / | / / | / / + * | / / | / / | / / + * | A-------D | A-------D | A-------D + * +-------------->X +-------------->X +-------------->Y + * XY_SKEW_FACTOR XZ_SKEW_FACTOR YZ_SKEW_FACTOR + */ +//#define SKEW_CORRECTION + +#if ENABLED(SKEW_CORRECTION) + // Input all length measurements here: + #define XY_DIAG_AC 282.8427124746 + #define XY_DIAG_BD 282.8427124746 + #define XY_SIDE_AD 200 + + // Or, set the default skew factors directly here + // to override the above measurements: + #define XY_SKEW_FACTOR 0.0 + + //#define SKEW_CORRECTION_FOR_Z + #if ENABLED(SKEW_CORRECTION_FOR_Z) + #define XZ_DIAG_AC 282.8427124746 + #define XZ_DIAG_BD 282.8427124746 + #define YZ_DIAG_AC 282.8427124746 + #define YZ_DIAG_BD 282.8427124746 + #define YZ_SIDE_AD 200 + #define XZ_SKEW_FACTOR 0.0 + #define YZ_SKEW_FACTOR 0.0 + #endif + + // Enable this option for M852 to set skew at runtime + //#define SKEW_CORRECTION_GCODE +#endif + +//============================================================================= +//============================= Additional Features =========================== +//============================================================================= + +// @section extras + +/** + * EEPROM + * + * Persistent storage to preserve configurable settings across reboots. + * + * M500 - Store settings to EEPROM. + * M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes) + * M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.) + */ +#define EEPROM_SETTINGS // Persistent storage with M500 and M501 +//#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release! +#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM. +#if ENABLED(EEPROM_SETTINGS) + #define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors. +#endif + +// +// Host Keepalive +// +// When enabled Marlin will send a busy status message to the host +// every couple of seconds when it can't accept commands. +// +#define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages +#define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113. +#define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating + +// +// M100 Free Memory Watcher +// +//#define M100_FREE_MEMORY_WATCHER // Add M100 (Free Memory Watcher) to debug memory usage + +// +// G20/G21 Inch mode support +// +//#define INCH_MODE_SUPPORT + +// +// M149 Set temperature units support +// +//#define TEMPERATURE_UNITS_SUPPORT + +// @section temperature + +// Preheat Constants +#define PREHEAT_1_LABEL "PLA" +#define PREHEAT_1_TEMP_HOTEND 200 +#define PREHEAT_1_TEMP_BED 70 +#define PREHEAT_1_FAN_SPEED 255 // Value from 0 to 255 + +#define PREHEAT_2_LABEL "ABS" +#define PREHEAT_2_TEMP_HOTEND 240 +#define PREHEAT_2_TEMP_BED 110 +#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255 + +/** + * Nozzle Park + * + * Park the nozzle at the given XYZ position on idle or G27. + * + * The "P" parameter controls the action applied to the Z axis: + * + * P0 (Default) If Z is below park Z raise the nozzle. + * P1 Raise the nozzle always to Z-park height. + * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS. + */ +#define NOZZLE_PARK_FEATURE + +#if ENABLED(NOZZLE_PARK_FEATURE) + // Specify a park position as { X, Y, Z_raise } + #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 } + #define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis) + #define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers) +#endif + +/** + * Clean Nozzle Feature -- EXPERIMENTAL + * + * Adds the G12 command to perform a nozzle cleaning process. + * + * Parameters: + * P Pattern + * S Strokes / Repetitions + * T Triangles (P1 only) + * + * Patterns: + * P0 Straight line (default). This process requires a sponge type material + * at a fixed bed location. "S" specifies strokes (i.e. back-forth motions) + * between the start / end points. + * + * P1 Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the + * number of zig-zag triangles to do. "S" defines the number of strokes. + * Zig-zags are done in whichever is the narrower dimension. + * For example, "G12 P1 S1 T3" will execute: + * + * -- + * | (X0, Y1) | /\ /\ /\ | (X1, Y1) + * | | / \ / \ / \ | + * A | | / \ / \ / \ | + * | | / \ / \ / \ | + * | (X0, Y0) | / \/ \/ \ | (X1, Y0) + * -- +--------------------------------+ + * |________|_________|_________| + * T1 T2 T3 + * + * P2 Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE. + * "R" specifies the radius. "S" specifies the stroke count. + * Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT. + * + * Caveats: The ending Z should be the same as starting Z. + * Attention: EXPERIMENTAL. G-code arguments may change. + * + */ +#define NOZZLE_CLEAN_FEATURE + +#if ENABLED(NOZZLE_CLEAN_FEATURE) + // Default number of pattern repetitions + #define NOZZLE_CLEAN_STROKES 12 + + // Default number of triangles + #define NOZZLE_CLEAN_TRIANGLES 3 + + // Specify positions as { X, Y, Z } + #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)} + #define NOZZLE_CLEAN_END_POINT { 100, 60, (Z_MIN_POS + 1) } + + // Circular pattern radius + #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5 + // Circular pattern circle fragments number + #define NOZZLE_CLEAN_CIRCLE_FN 10 + // Middle point of circle + #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT + + // Move the nozzle to the initial position after cleaning + #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z +#endif + +/** + * Print Job Timer + * + * Automatically start and stop the print job timer on M104/M109/M190. + * + * M104 (hotend, no wait) - high temp = none, low temp = stop timer + * M109 (hotend, wait) - high temp = start timer, low temp = stop timer + * M190 (bed, wait) - high temp = start timer, low temp = none + * + * The timer can also be controlled with the following commands: + * + * M75 - Start the print job timer + * M76 - Pause the print job timer + * M77 - Stop the print job timer + */ +#define PRINTJOB_TIMER_AUTOSTART + +/** + * Print Counter + * + * Track statistical data such as: + * + * - Total print jobs + * - Total successful print jobs + * - Total failed print jobs + * - Total time printing + * + * View the current statistics with M78. + */ +#define PRINTCOUNTER + +//============================================================================= +//============================= LCD and SD support ============================ +//============================================================================= + +// @section lcd + +/** + * LCD LANGUAGE + * + * Select the language to display on the LCD. These languages are available: + * + * en, an, bg, ca, cz, da, de, el, el-gr, es, eu, fi, fr, gl, hr, it, + * jp-kana, ko_KR, nl, pl, pt, pt-br, ru, sk, tr, uk, zh_CN, zh_TW, test + * + * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cz':'Czech', 'da':'Danish', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'jp-kana':'Japanese', 'ko_KR':'Korean (South Korea)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'ru':'Russian', 'sk':'Slovak', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Traditional)', 'test':'TEST' } + */ +#define LCD_LANGUAGE en + +/** + * LCD Character Set + * + * Note: This option is NOT applicable to Graphical Displays. + * + * All character-based LCDs provide ASCII plus one of these + * language extensions: + * + * - JAPANESE ... the most common + * - WESTERN ... with more accented characters + * - CYRILLIC ... for the Russian language + * + * To determine the language extension installed on your controller: + * + * - Compile and upload with LCD_LANGUAGE set to 'test' + * - Click the controller to view the LCD menu + * - The LCD will display Japanese, Western, or Cyrillic text + * + * See http://marlinfw.org/docs/development/lcd_language.html + * + * :['JAPANESE', 'WESTERN', 'CYRILLIC'] + */ +#define DISPLAY_CHARSET_HD44780 WESTERN + +/** + * Info Screen Style (0:Classic, 1:Prusa) + * + * :[0:'Classic', 1:'Prusa'] + */ +#define LCD_INFO_SCREEN_STYLE 0 + +/** + * SD CARD + * + * SD Card support is disabled by default. If your controller has an SD slot, + * you must uncomment the following option or it won't work. + * + */ +#define SDSUPPORT + +/** + * SD CARD: SPI SPEED + * + * Enable one of the following items for a slower SPI transfer speed. + * This may be required to resolve "volume init" errors. + */ +//#define SPI_SPEED SPI_HALF_SPEED +//#define SPI_SPEED SPI_QUARTER_SPEED +//#define SPI_SPEED SPI_EIGHTH_SPEED + +/** + * SD CARD: ENABLE CRC + * + * Use CRC checks and retries on the SD communication. + */ +//#define SD_CHECK_AND_RETRY + +/** + * LCD Menu Items + * + * Disable all menus and only display the Status Screen, or + * just remove some extraneous menu items to recover space. + */ +//#define NO_LCD_MENUS +//#define SLIM_LCD_MENUS + +// +// ENCODER SETTINGS +// +// This option overrides the default number of encoder pulses needed to +// produce one step. Should be increased for high-resolution encoders. +// +#define ENCODER_PULSES_PER_STEP 4 + +// +// Use this option to override the number of step signals required to +// move between next/prev menu items. +// +#define ENCODER_STEPS_PER_MENU_ITEM 1 + +/** + * Encoder Direction Options + * + * Test your encoder's behavior first with both options disabled. + * + * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION. + * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION. + * Reversed Value Editing only? Enable BOTH options. + */ + +// +// This option reverses the encoder direction everywhere. +// +// Set this option if CLOCKWISE causes values to DECREASE +// +#define REVERSE_ENCODER_DIRECTION + +// +// This option reverses the encoder direction for navigating LCD menus. +// +// If CLOCKWISE normally moves DOWN this makes it go UP. +// If CLOCKWISE normally moves UP this makes it go DOWN. +// +//#define REVERSE_MENU_DIRECTION + +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + +// +// Individual Axis Homing +// +// Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu. +// +#define INDIVIDUAL_AXIS_HOMING_MENU + +// +// SPEAKER/BUZZER +// +// If you have a speaker that can produce tones, enable it here. +// By default Marlin assumes you have a buzzer with a fixed frequency. +// +#define SPEAKER + +// +// The duration and frequency for the UI feedback sound. +// Set these to 0 to disable audio feedback in the LCD menus. +// +// Note: Test audio output with the G-Code: +// M300 S P +// +#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 2 +#define LCD_FEEDBACK_FREQUENCY_HZ 5000 + +//============================================================================= +//======================== LCD / Controller Selection ========================= +//======================== (Character-based LCDs) ========================= +//============================================================================= + +// +// RepRapDiscount Smart Controller. +// http://reprap.org/wiki/RepRapDiscount_Smart_Controller +// +// Note: Usually sold with a white PCB. +// +//#define REPRAP_DISCOUNT_SMART_CONTROLLER + +// +// Original RADDS LCD Display+Encoder+SDCardReader +// http://doku.radds.org/dokumentation/lcd-display/ +// +//#define RADDS_DISPLAY + +// +// ULTIMAKER Controller. +// +//#define ULTIMAKERCONTROLLER + +// +// ULTIPANEL as seen on Thingiverse. +// +//#define ULTIPANEL + +// +// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3) +// http://reprap.org/wiki/PanelOne +// +//#define PANEL_ONE + +// +// GADGETS3D G3D LCD/SD Controller +// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel +// +// Note: Usually sold with a blue PCB. +// +//#define G3D_PANEL + +// +// RigidBot Panel V1.0 +// http://www.inventapart.com/ +// +//#define RIGIDBOT_PANEL + +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// ANET and Tronxy 20x4 Controller +// +//#define ZONESTAR_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin. + // This LCD is known to be susceptible to electrical interference + // which scrambles the display. Pressing any button clears it up. + // This is a LCD2004 display with 5 analog buttons. + +// +// Generic 16x2, 16x4, 20x2, or 20x4 character-based LCD. +// +//#define ULTRA_LCD + +//============================================================================= +//======================== LCD / Controller Selection ========================= +//===================== (I2C and Shift-Register LCDs) ===================== +//============================================================================= + +// +// CONTROLLER TYPE: I2C +// +// Note: These controllers require the installation of Arduino's LiquidCrystal_I2C +// library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C +// + +// +// Elefu RA Board Control Panel +// http://www.elefu.com/index.php?route=product/product&product_id=53 +// +//#define RA_CONTROL_PANEL + +// +// Sainsmart (YwRobot) LCD Displays +// +// These require F.Malpartida's LiquidCrystal_I2C library +// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home +// +//#define LCD_SAINSMART_I2C_1602 +//#define LCD_SAINSMART_I2C_2004 + +// +// Generic LCM1602 LCD adapter +// +//#define LCM1602 + +// +// PANELOLU2 LCD with status LEDs, +// separate encoder and click inputs. +// +// Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later. +// For more info: https://github.com/lincomatic/LiquidTWI2 +// +// Note: The PANELOLU2 encoder click input can either be directly connected to +// a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1). +// +//#define LCD_I2C_PANELOLU2 + +// +// Panucatt VIKI LCD with status LEDs, +// integrated click & L/R/U/D buttons, separate encoder inputs. +// +//#define LCD_I2C_VIKI + +// +// CONTROLLER TYPE: Shift register panels +// + +// +// 2-wire Non-latching LCD SR from https://goo.gl/aJJ4sH +// LCD configuration: http://reprap.org/wiki/SAV_3D_LCD +// +//#define SAV_3DLCD + +// +// 3-wire SR LCD with strobe using 74HC4094 +// https://github.com/mikeshub/SailfishLCD +// Uses the code directly from Sailfish +// +//#define FF_INTERFACEBOARD + +//============================================================================= +//======================= LCD / Controller Selection ======================= +//========================= (Graphical LCDs) ======================== +//============================================================================= + +// +// CONTROLLER TYPE: Graphical 128x64 (DOGM) +// +// IMPORTANT: The U8glib library is required for Graphical Display! +// https://github.com/olikraus/U8glib_Arduino +// + +// +// RepRapDiscount FULL GRAPHIC Smart Controller +// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller +// +#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER + +// +// ReprapWorld Graphical LCD +// https://reprapworld.com/?products_details&products_id/1218 +// +//#define REPRAPWORLD_GRAPHICAL_LCD + +// +// Activate one of these if you have a Panucatt Devices +// Viki 2.0 or mini Viki with Graphic LCD +// http://panucatt.com +// +//#define VIKI2 +//#define miniVIKI + +// +// MakerLab Mini Panel with graphic +// controller and SD support - http://reprap.org/wiki/Mini_panel +// +//#define MINIPANEL + +// +// MaKr3d Makr-Panel with graphic controller and SD support. +// http://reprap.org/wiki/MaKr3d_MaKrPanel +// +//#define MAKRPANEL + +// +// Adafruit ST7565 Full Graphic Controller. +// https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/ +// +//#define ELB_FULL_GRAPHIC_CONTROLLER + +// +// BQ LCD Smart Controller shipped by +// default with the BQ Hephestos 2 and Witbox 2. +// +//#define BQ_LCD_SMART_CONTROLLER + +// +// Cartesio UI +// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// +//#define CARTESIO_UI + +// +// LCD for Melzi Card with Graphical LCD +// +//#define LCD_FOR_MELZI + +// +// Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder +// https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) +// +//#define ULTI_CONTROLLER + +// +// MKS MINI12864 with graphic controller and SD support +// https://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// FYSETC variant of the MINI12864 graphic controller with SD support +// https://wiki.fysetc.com/Mini12864_Panel/ +// +//#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default +//#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) +//#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// ANET and Tronxy Graphical Controller +// +// Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6 +// A clone of the RepRapDiscount full graphics display but with +// different pins/wiring (see pins_ANET_10.h). +// +//#define ANET_FULL_GRAPHICS_LCD + +// +// AZSMZ 12864 LCD with SD +// https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html +// +//#define AZSMZ_12864 + +// +// Silvergate GLCD controller +// http://github.com/android444/Silvergate +// +//#define SILVER_GATE_GLCD_CONTROLLER + +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + +//============================================================================= +//========================== Extensible UI Displays =========================== +//============================================================================= + +// +// DGUS Touch Display with DWIN OS +// +//#define DGUS_LCD + +// +// Touch-screen LCD for Malyan M200 printers +// +//#define MALYAN_LCD + +// +// Third-party or vendor-customized controller interfaces. +// Sources should be installed in 'src/lcd/extensible_ui'. +// +//#define EXTENSIBLE_UI + +//============================================================================= +//=============================== Graphical TFTs ============================== +//============================================================================= + +// +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) +// +//#define FSMC_GRAPHICAL_TFT + +//============================================================================= +//============================ Other Controllers ============================ +//============================================================================= + +// +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 +// +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif + +// +// RepRapWorld REPRAPWORLD_KEYPAD v1.1 +// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626 +// +// REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key +// is pressed, a value of 10.0 means 10mm per click. +// +//#define REPRAPWORLD_KEYPAD +//#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 + +//============================================================================= +//=============================== Extra Features ============================== +//============================================================================= + +// @section extras + +// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino +//#define FAST_PWM_FAN + +// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency +// which is not as annoying as with the hardware PWM. On the other hand, if this frequency +// is too low, you should also increment SOFT_PWM_SCALE. +//#define FAN_SOFT_PWM + +// Incrementing this by 1 will double the software PWM frequency, +// affecting heaters, and the fan if FAN_SOFT_PWM is enabled. +// However, control resolution will be halved for each increment; +// at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] +#define SOFT_PWM_SCALE 0 + +// If SOFT_PWM_SCALE is set to a value higher than 0, dithering can +// be used to mitigate the associated resolution loss. If enabled, +// some of the PWM cycles are stretched so on average the desired +// duty cycle is attained. +//#define SOFT_PWM_DITHER + +// Temperature status LEDs that display the hotend and bed temperature. +// If all hotends, bed temperature, and target temperature are under 54C +// then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis) +//#define TEMP_STAT_LEDS + +// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure +//#define SF_ARC_FIX + +// Support for the BariCUDA Paste Extruder +//#define BARICUDA + +// Support for BlinkM/CyzRgb +//#define BLINKM + +// Support for PCA9632 PWM LED driver +//#define PCA9632 + +// Support for PCA9533 PWM LED driver +// https://github.com/mikeshub/SailfishRGB_LED +//#define PCA9533 + +/** + * RGB LED / LED Strip Control + * + * Enable support for an RGB LED connected to 5V digital pins, or + * an RGB Strip connected to MOSFETs controlled by digital pins. + * + * Adds the M150 command to set the LED (or LED strip) color. + * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of + * luminance values can be set from 0 to 255. + * For Neopixel LED an overall brightness parameter is also available. + * + * *** CAUTION *** + * LED Strips require a MOSFET Chip between PWM lines and LEDs, + * as the Arduino cannot handle the current the LEDs will require. + * Failure to follow this precaution can destroy your Arduino! + * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * more current than the Arduino 5V linear regulator can produce. + * *** CAUTION *** + * + * LED Type. Enable only one of the following two options. + * + */ +//#define RGB_LED +//#define RGBW_LED + +#if EITHER(RGB_LED, RGBW_LED) + //#define RGB_LED_R_PIN 34 + //#define RGB_LED_G_PIN 43 + //#define RGB_LED_B_PIN 35 + //#define RGB_LED_W_PIN -1 +#endif + +// Support for Adafruit Neopixel LED driver +//#define NEOPIXEL_LED +#if ENABLED(NEOPIXEL_LED) + #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. + #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) + //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup + + // Use a single Neopixel LED for static (background) lighting + //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use + //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W +#endif + +/** + * Printer Event LEDs + * + * During printing, the LEDs will reflect the printer status: + * + * - Gradually change from blue to violet as the heated bed gets to target temp + * - Gradually change from violet to red as the hotend gets to temperature + * - Change to white to illuminate work surface + * - Change to green once print has finished + * - Turn off after the print has finished and the user has pushed a button + */ +#if ANY(BLINKM, RGB_LED, RGBW_LED, PCA9632, PCA9533, NEOPIXEL_LED) + #define PRINTER_EVENT_LEDS +#endif + +/** + * R/C SERVO support + * Sponsored by TrinityLabs, Reworked by codexmas + */ + +/** + * Number of servos + * + * For some servo-related options NUM_SERVOS will be set automatically. + * Set this manually if there are extra servos needing manual control. + * Leave undefined or set to 0 to entirely disable the servo subsystem. + */ +//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command + +// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. +// 300ms is a good value but you can try less delay. +// If the servo can't reach the requested position, increase it. +#define SERVO_DELAY { 300 } + +// Only power servos during movement, otherwise leave off to prevent jitter +//#define DEACTIVATE_SERVOS_AFTER_MOVE + +// Allow servo angle to be edited and saved to EEPROM +//#define EDITABLE_SERVO_ANGLES diff --git a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h new file mode 100644 index 0000000000..a5f9db1b2f --- /dev/null +++ b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h @@ -0,0 +1,2561 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Configuration_adv.h + * + * Advanced settings. + * Only change these if you know exactly what you're doing. + * Some of these settings can damage your printer if improperly set! + * + * Basic settings can be found in Configuration.h + * + */ +#define CONFIGURATION_ADV_H_VERSION 020000 + +// @section temperature + +//=========================================================================== +//=============================Thermal Settings ============================ +//=========================================================================== + +// +// Custom Thermistor 1000 parameters +// +#if TEMP_SENSOR_0 == 1000 + #define HOTEND0_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND0_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND0_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_1 == 1000 + #define HOTEND1_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND1_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND1_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_2 == 1000 + #define HOTEND2_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND2_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND2_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_3 == 1000 + #define HOTEND3_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND3_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND3_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_4 == 1000 + #define HOTEND4_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND4_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND4_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_5 == 1000 + #define HOTEND5_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND5_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND5_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_BED == 1000 + #define BED_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define BED_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define BED_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_CHAMBER == 1000 + #define CHAMBER_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define CHAMBER_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define CHAMBER_BETA 3950 // Beta value +#endif + +// +// Hephestos 2 24V heated bed upgrade kit. +// https://store.bq.com/en/heated-bed-kit-hephestos2 +// +//#define HEPHESTOS2_HEATED_BED_KIT +#if ENABLED(HEPHESTOS2_HEATED_BED_KIT) + #undef TEMP_SENSOR_BED + #define TEMP_SENSOR_BED 70 + #define HEATER_BED_INVERTING true +#endif + +/** + * Heated Chamber settings + */ +#if TEMP_SENSOR_CHAMBER + #define CHAMBER_MINTEMP 5 + #define CHAMBER_MAXTEMP 60 + #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target + //#define CHAMBER_LIMIT_SWITCHING + //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin + //#define HEATER_CHAMBER_INVERTING false +#endif + +#if DISABLED(PIDTEMPBED) + #define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control + #if ENABLED(BED_LIMIT_SWITCHING) + #define BED_HYSTERESIS 2 // Only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS + #endif +#endif + +/** + * Thermal Protection provides additional protection to your printer from damage + * and fire. Marlin always includes safe min and max temperature ranges which + * protect against a broken or disconnected thermistor wire. + * + * The issue: If a thermistor falls out, it will report the much lower + * temperature of the air in the room, and the the firmware will keep + * the heater on. + * + * The solution: Once the temperature reaches the target, start observing. + * If the temperature stays too far below the target (hysteresis) for too + * long (period), the firmware will halt the machine as a safety precaution. + * + * If you get false positives for "Thermal Runaway", increase + * THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD + */ +#if ENABLED(THERMAL_PROTECTION_HOTENDS) + #define THERMAL_PROTECTION_PERIOD 40 // Seconds + #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius + + //#define ADAPTIVE_FAN_SLOWING // Slow part cooling fan if temperature drops + #if BOTH(ADAPTIVE_FAN_SLOWING, PIDTEMP) + //#define NO_FAN_SLOWING_IN_PID_TUNING // Don't slow fan speed during M303 + #endif + + /** + * Whenever an M104, M109, or M303 increases the target temperature, the + * firmware will wait for the WATCH_TEMP_PERIOD to expire. If the temperature + * hasn't increased by WATCH_TEMP_INCREASE degrees, the machine is halted and + * requires a hard reset. This test restarts with any M104/M109/M303, but only + * if the current temperature is far enough below the target for a reliable + * test. + * + * If you get false positives for "Heating failed", increase WATCH_TEMP_PERIOD + * and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set + * below 2. + */ + #define WATCH_TEMP_PERIOD 20 // Seconds + #define WATCH_TEMP_INCREASE 2 // Degrees Celsius +#endif + +/** + * Thermal Protection parameters for the bed are just as above for hotends. + */ +#if ENABLED(THERMAL_PROTECTION_BED) + #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds + #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius + + /** + * As described above, except for the bed (M140/M190/M303). + */ + #define WATCH_BED_TEMP_PERIOD 60 // Seconds + #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius +#endif + +/** + * Thermal Protection parameters for the heated chamber. + */ +#if ENABLED(THERMAL_PROTECTION_CHAMBER) + #define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds + #define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius + + /** + * Heated chamber watch settings (M141/M191). + */ + #define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds + #define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius +#endif + +#if ENABLED(PIDTEMP) + // Add an experimental additional term to the heater power, proportional to the extrusion speed. + // A well-chosen Kc value should add just enough power to melt the increased material volume. + //#define PID_EXTRUSION_SCALING + #if ENABLED(PID_EXTRUSION_SCALING) + #define DEFAULT_Kc (100) //heating power=Kc*(e_speed) + #define LPQ_MAX_LEN 50 + #endif +#endif + +/** + * Automatic Temperature: + * The hotend target temperature is calculated by all the buffered lines of gcode. + * The maximum buffered steps/sec of the extruder motor is called "se". + * Start autotemp mode with M109 S B F + * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by + * mintemp and maxtemp. Turn this off by executing M109 without F* + * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp. + * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode + */ +#define AUTOTEMP +#if ENABLED(AUTOTEMP) + #define AUTOTEMP_OLDWEIGHT 0.98 +#endif + +// Show extra position information in M114 +//#define M114_DETAIL + +// Show Temperature ADC value +// Enable for M105 to include ADC values read from temperature sensors. +//#define SHOW_TEMP_ADC_VALUES + +/** + * High Temperature Thermistor Support + * + * Thermistors able to support high temperature tend to have a hard time getting + * good readings at room and lower temperatures. This means HEATER_X_RAW_LO_TEMP + * will probably be caught when the heating element first turns on during the + * preheating process, which will trigger a min_temp_error as a safety measure + * and force stop everything. + * To circumvent this limitation, we allow for a preheat time (during which, + * min_temp_error won't be triggered) and add a min_temp buffer to handle + * aberrant readings. + * + * If you want to enable this feature for your hotend thermistor(s) + * uncomment and set values > 0 in the constants below + */ + +// The number of consecutive low temperature errors that can occur +// before a min_temp_error is triggered. (Shouldn't be more than 10.) +//#define MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED 0 + +// The number of milliseconds a hotend will preheat before starting to check +// the temperature. This value should NOT be set to the time it takes the +// hot end to reach the target temperature, but the time it takes to reach +// the minimum temperature your thermistor can read. The lower the better/safer. +// This shouldn't need to be more than 30 seconds (30000) +//#define MILLISECONDS_PREHEAT_TIME 0 + +// @section extruder + +// Extruder runout prevention. +// If the machine is idle and the temperature over MINTEMP +// then extrude some filament every couple of SECONDS. +//#define EXTRUDER_RUNOUT_PREVENT +#if ENABLED(EXTRUDER_RUNOUT_PREVENT) + #define EXTRUDER_RUNOUT_MINTEMP 190 + #define EXTRUDER_RUNOUT_SECONDS 30 + #define EXTRUDER_RUNOUT_SPEED 1500 // (mm/m) + #define EXTRUDER_RUNOUT_EXTRUDE 5 // (mm) +#endif + +// @section temperature + +// Calibration for AD595 / AD8495 sensor to adjust temperature measurements. +// The final temperature is calculated as (measuredTemp * GAIN) + OFFSET. +#define TEMP_SENSOR_AD595_OFFSET 0.0 +#define TEMP_SENSOR_AD595_GAIN 1.0 +#define TEMP_SENSOR_AD8495_OFFSET 0.0 +#define TEMP_SENSOR_AD8495_GAIN 1.0 + +/** + * Controller Fan + * To cool down the stepper drivers and MOSFETs. + * + * The fan will turn on automatically whenever any stepper is enabled + * and turn off after a set period after all steppers are turned off. + */ +//#define USE_CONTROLLER_FAN +#if ENABLED(USE_CONTROLLER_FAN) + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled + #define CONTROLLERFAN_SPEED 255 // 255 == full speed +#endif + +// When first starting the main fan, run it at full speed for the +// given number of milliseconds. This gets the fan spinning reliably +// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) +#define FAN_KICKSTART_TIME 100 + +/** + * PWM Fan Scaling + * + * Define the min/max speeds for PWM fans (as set with M106). + * + * With these options the M106 0-255 value range is scaled to a subset + * to ensure that the fan has enough power to spin, or to run lower + * current fans with higher current. (e.g., 5V/12V fans with 12V/24V) + * Value 0 always turns off the fan. + * + * Define one or both of these to override the default 0-255 range. + */ +//#define FAN_MIN_PWM 50 +//#define FAN_MAX_PWM 128 + +/** + * FAST PWM FAN Settings + * + * Use to change the FAST FAN PWM frequency (if enabled in Configuration.h) + * Combinations of PWM Modes, prescale values and TOP resolutions are used internally to produce a + * frequency as close as possible to the desired frequency. + * + * FAST_PWM_FAN_FREQUENCY [undefined by default] + * Set this to your desired frequency. + * If left undefined this defaults to F = F_CPU/(2*255*1) + * ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers + * These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required + * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior. + * + * USE_OCR2A_AS_TOP [undefined by default] + * Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2: + * 16MHz MCUs: [62.5KHz, 31.4KHz (default), 7.8KHz, 3.92KHz, 1.95KHz, 977Hz, 488Hz, 244Hz, 60Hz, 122Hz, 30Hz] + * 20MHz MCUs: [78.1KHz, 39.2KHz (default), 9.77KHz, 4.9KHz, 2.44KHz, 1.22KHz, 610Hz, 305Hz, 153Hz, 76Hz, 38Hz] + * A greater range can be achieved by enabling USE_OCR2A_AS_TOP. But note that this option blocks the use of + * PWM on pin OC2A. Only use this option if you don't need PWM on 0C2A. (Check your schematic.) + * USE_OCR2A_AS_TOP sacrifices duty cycle control resolution to achieve this broader range of frequencies. + */ +#if ENABLED(FAST_PWM_FAN) + //#define FAST_PWM_FAN_FREQUENCY 31400 + //#define USE_OCR2A_AS_TOP +#endif + +// @section extruder + +/** + * Extruder cooling fans + * + * Extruder auto fans automatically turn on when their extruders' + * temperatures go above EXTRUDER_AUTO_FAN_TEMPERATURE. + * + * Your board's pins file specifies the recommended pins. Override those here + * or set to -1 to disable completely. + * + * Multiple extruders can be assigned to the same pin in which case + * the fan will turn on when any selected extruder is above the threshold. + */ +#define E0_AUTO_FAN_PIN 7 +#define E1_AUTO_FAN_PIN -1 +#define E2_AUTO_FAN_PIN -1 +#define E3_AUTO_FAN_PIN -1 +#define E4_AUTO_FAN_PIN -1 +#define E5_AUTO_FAN_PIN -1 +#define CHAMBER_AUTO_FAN_PIN -1 + +#define EXTRUDER_AUTO_FAN_TEMPERATURE 50 +#define EXTRUDER_AUTO_FAN_SPEED 255 // 255 == full speed +#define CHAMBER_AUTO_FAN_TEMPERATURE 30 +#define CHAMBER_AUTO_FAN_SPEED 255 + +/** + * Part-Cooling Fan Multiplexer + * + * This feature allows you to digitally multiplex the fan output. + * The multiplexer is automatically switched at tool-change. + * Set FANMUX[012]_PINs below for up to 2, 4, or 8 multiplexed fans. + */ +#define FANMUX0_PIN -1 +#define FANMUX1_PIN -1 +#define FANMUX2_PIN -1 + +/** + * M355 Case Light on-off / brightness + */ +//#define CASE_LIGHT_ENABLE +#if ENABLED(CASE_LIGHT_ENABLE) + //#define CASE_LIGHT_PIN 4 // Override the default pin if needed + #define INVERT_CASE_LIGHT false // Set true if Case Light is ON when pin is LOW + #define CASE_LIGHT_DEFAULT_ON true // Set default power-up state on + #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105 // Set default power-up brightness (0-255, requires PWM pin) + //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu + //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. + //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) + #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } + #endif +#endif + +// @section homing + +// If you want endstops to stay on (by default) even when not homing +// enable this option. Override at any time with M120, M121. +//#define ENDSTOPS_ALWAYS_ON_DEFAULT + +// @section extras + +//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats. + +// Employ an external closed loop controller. Override pins here if needed. +//#define EXTERNAL_CLOSED_LOOP_CONTROLLER +#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER) + //#define CLOSED_LOOP_ENABLE_PIN -1 + //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1 +#endif + +/** + * Dual Steppers / Dual Endstops + * + * This section will allow you to use extra E drivers to drive a second motor for X, Y, or Z axes. + * + * For example, set X_DUAL_STEPPER_DRIVERS setting to use a second motor. If the motors need to + * spin in opposite directions set INVERT_X2_VS_X_DIR. If the second motor needs its own endstop + * set X_DUAL_ENDSTOPS. This can adjust for "racking." Use X2_USE_ENDSTOP to set the endstop plug + * that should be used for the second endstop. Extra endstops will appear in the output of 'M119'. + * + * Use X_DUAL_ENDSTOP_ADJUSTMENT to adjust for mechanical imperfection. After homing both motors + * this offset is applied to the X2 motor. To find the offset home the X axis, and measure the error + * in X2. Dual endstop offsets can be set at runtime with 'M666 X Y Z'. + */ + +//#define X_DUAL_STEPPER_DRIVERS +#if ENABLED(X_DUAL_STEPPER_DRIVERS) + #define INVERT_X2_VS_X_DIR true // Set 'true' if X motors should rotate in opposite directions + //#define X_DUAL_ENDSTOPS + #if ENABLED(X_DUAL_ENDSTOPS) + #define X2_USE_ENDSTOP _XMAX_ + #define X_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Y_DUAL_STEPPER_DRIVERS +#if ENABLED(Y_DUAL_STEPPER_DRIVERS) + #define INVERT_Y2_VS_Y_DIR true // Set 'true' if Y motors should rotate in opposite directions + //#define Y_DUAL_ENDSTOPS + #if ENABLED(Y_DUAL_ENDSTOPS) + #define Y2_USE_ENDSTOP _YMAX_ + #define Y_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Z_DUAL_STEPPER_DRIVERS +#if ENABLED(Z_DUAL_STEPPER_DRIVERS) + //#define Z_DUAL_ENDSTOPS + #if ENABLED(Z_DUAL_ENDSTOPS) + #define Z2_USE_ENDSTOP _XMAX_ + #define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Z_TRIPLE_STEPPER_DRIVERS +#if ENABLED(Z_TRIPLE_STEPPER_DRIVERS) + //#define Z_TRIPLE_ENDSTOPS + #if ENABLED(Z_TRIPLE_ENDSTOPS) + #define Z2_USE_ENDSTOP _XMAX_ + #define Z3_USE_ENDSTOP _YMAX_ + #define Z_TRIPLE_ENDSTOPS_ADJUSTMENT2 0 + #define Z_TRIPLE_ENDSTOPS_ADJUSTMENT3 0 + #endif +#endif + +/** + * Dual X Carriage + * + * This setup has two X carriages that can move independently, each with its own hotend. + * The carriages can be used to print an object with two colors or materials, or in + * "duplication mode" it can print two identical or X-mirrored objects simultaneously. + * The inactive carriage is parked automatically to prevent oozing. + * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. + * By default the X2 stepper is assigned to the first unused E plug on the board. + * + * The following Dual X Carriage modes can be selected with M605 S: + * + * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel + * results as long as it supports dual X-carriages. (M605 S0) + * + * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so + * that additional slicer support is not required. (M605 S1) + * + * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with + * the first X-carriage and extruder, to print 2 copies of the same object at the same time. + * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and + * follow with M605 S2 to initiate duplicated movement. + * + * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates + * the movement of the first except the second extruder is reversed in the X axis. + * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and + * follow with M605 S3 to initiate mirrored movement. + */ +//#define DUAL_X_CARRIAGE +#if ENABLED(DUAL_X_CARRIAGE) + #define X1_MIN_POS X_MIN_POS // Set to X_MIN_POS + #define X1_MAX_POS X_BED_SIZE // Set a maximum so the first X-carriage can't hit the parked second X-carriage + #define X2_MIN_POS 80 // Set a minimum to ensure the second X-carriage can't hit the parked first X-carriage + #define X2_MAX_POS 353 // Set this to the distance between toolheads when both heads are homed + #define X2_HOME_DIR 1 // Set to 1. The second X-carriage always homes to the maximum endstop position + #define X2_HOME_POS X2_MAX_POS // Default X2 home position. Set to X2_MAX_POS. + // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software + // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops + // without modifying the firmware (through the "M218 T1 X???" command). + // Remember: you should set the second extruder x-offset to 0 in your slicer. + + // This is the default power-up mode which can be later using M605. + #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_AUTO_PARK_MODE + + // Default x offset in duplication mode (typically set to half print bed width) + #define DEFAULT_DUPLICATION_X_OFFSET 100 + +#endif // DUAL_X_CARRIAGE + +// Activate a solenoid on the active extruder with M380. Disable all with M381. +// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid. +//#define EXT_SOLENOID + +// @section homing + +// Homing hits each endstop, retracts by these distances, then does a slower bump. +#define X_HOME_BUMP_MM 5 +#define Y_HOME_BUMP_MM 5 +#define Z_HOME_BUMP_MM 2 +#define HOMING_BUMP_DIVISOR { 2, 2, 4 } // Re-Bump Speed Divisor (Divides the Homing Feedrate) +#define QUICK_HOME // If homing includes X and Y, do a diagonal move initially +//#define HOMING_BACKOFF_MM { 2, 2, 2 } // (mm) Move away from the endstops after homing + +// When G28 is called, this option will make Y home before X +//#define HOME_Y_BEFORE_X + +// Enable this if X or Y can't home without homing the other axis first. +//#define CODEPENDENT_XY_HOMING + +#if ENABLED(BLTOUCH) + /** + * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES + * Do not activate settings that the probe might not understand. Clones might misunderstand + * advanced commands. + * + * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then + * check the wiring of the BROWN, RED and ORANGE wires. + * + * Note: If the trigger signal of your probe is not being recognized, it has been very often + * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable" + * like they would be with a real switch. So please check the wiring first. + * + * Settings for all BLTouch and clone probes: + */ + + // Safety: The probe needs time to recognize the command. + // Minimum command delay (ms). Enable and increase if needed. + //#define BLTOUCH_DELAY 500 + + /** + * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones: + */ + + // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful + // in special cases, like noisy or filtered input configurations. + //#define BLTOUCH_FORCE_SW_MODE + + /** + * Settings for BLTouch Smart 3.0 and 3.1 + * Summary: + * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes + * - High-Speed mode + * - Disable LCD voltage options + */ + + /** + * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller! + * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup. + * If disabled, OD mode is the hard-coded default on 3.0 + * On startup, Marlin will compare its eeprom to this vale. If the selected mode + * differs, a mode set eeprom write will be completed at initialization. + * Use the option below to force an eeprom write to a V3.1 probe regardless. + */ + //#define BLTOUCH_SET_5V_MODE + + /** + * Safety: Activate if connecting a probe with an unknown voltage mode. + * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0 + * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write ) + * To preserve the life of the probe, use this once then turn it off and re-flash. + */ + //#define BLTOUCH_FORCE_MODE_SET + + /** + * Use "HIGH SPEED" mode for probing. + * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems. + * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function + * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state. + */ + //#define BLTOUCH_HS_MODE + + // Safety: Enable voltage mode settings in the LCD menu. + //#define BLTOUCH_LCD_VOLTAGE_MENU + +#endif // BLTOUCH + +/** + * Z Steppers Auto-Alignment + * Add the G34 command to align multiple Z steppers using a bed probe. + */ +//#define Z_STEPPER_AUTO_ALIGN +#if ENABLED(Z_STEPPER_AUTO_ALIGN) + // Define probe X and Y positions for Z1, Z2 [, Z3] + #define Z_STEPPER_ALIGN_X { 10, 150, 290 } + #define Z_STEPPER_ALIGN_Y { 290, 10, 290 } + // Set number of iterations to align + #define Z_STEPPER_ALIGN_ITERATIONS 3 + // Enable to restore leveling setup after operation + #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + + // Use the amplification factor to de-/increase correction step. + // In case the stepper (spindle) position is further out than the test point + // Use a value > 1. NOTE: This may cause instability + #define Z_STEPPER_ALIGN_AMP 1.0 + // Stop criterion. If the accuracy is better than this stop iterating early + #define Z_STEPPER_ALIGN_ACC 0.02 +#endif + +// @section machine + +#define AXIS_RELATIVE_MODES { false, false, false, false } + +// Add a Duplicate option for well-separated conjoined nozzles +//#define MULTI_NOZZLE_DUPLICATION + +// By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step. +#define INVERT_X_STEP_PIN false +#define INVERT_Y_STEP_PIN false +#define INVERT_Z_STEP_PIN false +#define INVERT_E_STEP_PIN false + +// Default stepper release if idle. Set to 0 to deactivate. +// Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true. +// Time can be set by M18 and M84. +#define DEFAULT_STEPPER_DEACTIVE_TIME 120 +#define DISABLE_INACTIVE_X true +#define DISABLE_INACTIVE_Y true +#define DISABLE_INACTIVE_Z true // Set to false if the nozzle will fall down on your printed part when print has finished. +#define DISABLE_INACTIVE_E true + +#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate +#define DEFAULT_MINTRAVELFEEDRATE 0.0 + +//#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated + +// @section lcd + +#if EITHER(ULTIPANEL, EXTENSIBLE_UI) + #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #if ENABLED(ULTIPANEL) + #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" + #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen + #endif +#endif + +// @section extras + +// minimum time in microseconds that a movement needs to take if the buffer is emptied. +#define DEFAULT_MINSEGMENTTIME 20000 + +// If defined the movements slow down when the look ahead buffer is only half full +#define SLOWDOWN + +// Frequency limit +// See nophead's blog for more info +// Not working O +//#define XY_FREQUENCY_LIMIT 15 + +// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end +// of the buffer and all stops. This should not be much greater than zero and should only be changed +// if unwanted behavior is observed on a user's machine when running at very slow speeds. +#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s) + +// +// Backlash Compensation +// Adds extra movement to axes on direction-changes to account for backlash. +// +//#define BACKLASH_COMPENSATION +#if ENABLED(BACKLASH_COMPENSATION) + // Define values for backlash distance and correction. + // If BACKLASH_GCODE is enabled these values are the defaults. + #define BACKLASH_DISTANCE_MM { 0, 0, 0 } // (mm) + #define BACKLASH_CORRECTION 0.0 // 0.0 = no correction; 1.0 = full correction + + // Set BACKLASH_SMOOTHING_MM to spread backlash correction over multiple segments + // to reduce print artifacts. (Enabling this is costly in memory and computation!) + //#define BACKLASH_SMOOTHING_MM 3 // (mm) + + // Add runtime configuration and tuning of backlash values (M425) + //#define BACKLASH_GCODE + + #if ENABLED(BACKLASH_GCODE) + // Measure the Z backlash when probing (G29) and set with "M425 Z" + #define MEASURE_BACKLASH_WHEN_PROBING + + #if ENABLED(MEASURE_BACKLASH_WHEN_PROBING) + // When measuring, the probe will move up to BACKLASH_MEASUREMENT_LIMIT + // mm away from point of contact in BACKLASH_MEASUREMENT_RESOLUTION + // increments while checking for the contact to be broken. + #define BACKLASH_MEASUREMENT_LIMIT 0.5 // (mm) + #define BACKLASH_MEASUREMENT_RESOLUTION 0.005 // (mm) + #define BACKLASH_MEASUREMENT_FEEDRATE Z_PROBE_SPEED_SLOW // (mm/m) + #endif + #endif +#endif + +/** + * Automatic backlash, position and hotend offset calibration + * + * Enable G425 to run automatic calibration using an electrically- + * conductive cube, bolt, or washer mounted on the bed. + * + * G425 uses the probe to touch the top and sides of the calibration object + * on the bed and measures and/or correct positional offsets, axis backlash + * and hotend offsets. + * + * Note: HOTEND_OFFSET and CALIBRATION_OBJECT_CENTER must be set to within + * ±5mm of true values for G425 to succeed. + */ +//#define CALIBRATION_GCODE +#if ENABLED(CALIBRATION_GCODE) + + #define CALIBRATION_MEASUREMENT_RESOLUTION 0.01 // mm + + #define CALIBRATION_FEEDRATE_SLOW 60 // mm/m + #define CALIBRATION_FEEDRATE_FAST 1200 // mm/m + #define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/m + + // The following parameters refer to the conical section of the nozzle tip. + #define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm + #define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm + + // Uncomment to enable reporting (required for "G425 V", but consumes PROGMEM). + //#define CALIBRATION_REPORTING + + // The true location and dimension the cube/bolt/washer on the bed. + #define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0} // mm + #define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0} // mm + + // Comment out any sides which are unreachable by the probe. For best + // auto-calibration results, all sides must be reachable. + #define CALIBRATION_MEASURE_RIGHT + #define CALIBRATION_MEASURE_FRONT + #define CALIBRATION_MEASURE_LEFT + #define CALIBRATION_MEASURE_BACK + + // Probing at the exact top center only works if the center is flat. If + // probing on a screwhead or hollow washer, probe near the edges. + //#define CALIBRATION_MEASURE_AT_TOP_EDGES + + // Define pin which is read during calibration + #ifndef CALIBRATION_PIN + #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop + #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin + //#define CALIBRATION_PIN_PULLDOWN + #define CALIBRATION_PIN_PULLUP + #endif +#endif + +/** + * Adaptive Step Smoothing increases the resolution of multi-axis moves, particularly at step frequencies + * below 1kHz (for AVR) or 10kHz (for ARM), where aliasing between axes in multi-axis moves causes audible + * vibration and surface artifacts. The algorithm adapts to provide the best possible step smoothing at the + * lowest stepping frequencies. + */ +//#define ADAPTIVE_STEP_SMOOTHING + +/** + * Custom Microstepping + * Override as-needed for your setup. Up to 3 MS pins are supported. + */ +//#define MICROSTEP1 LOW,LOW,LOW +//#define MICROSTEP2 HIGH,LOW,LOW +//#define MICROSTEP4 LOW,HIGH,LOW +//#define MICROSTEP8 HIGH,HIGH,LOW +//#define MICROSTEP16 LOW,LOW,HIGH +//#define MICROSTEP32 HIGH,LOW,HIGH + +// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU. +#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16] + +/** + * @section stepper motor current + * + * Some boards have a means of setting the stepper motor current via firmware. + * + * The power on motor currents are set by: + * PWM_MOTOR_CURRENT - used by MINIRAMBO & ULTIMAIN_2 + * known compatible chips: A4982 + * DIGIPOT_MOTOR_CURRENT - used by BQ_ZUM_MEGA_3D, RAMBO & SCOOVO_X9H + * known compatible chips: AD5206 + * DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2 + * known compatible chips: MCP4728 + * DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, AZTEEG_X5_MINI_WIFI, MIGHTYBOARD_REVE + * known compatible chips: MCP4451, MCP4018 + * + * Motor currents can also be set by M907 - M910 and by the LCD. + * M907 - applies to all. + * M908 - BQ_ZUM_MEGA_3D, RAMBO, PRINTRBOARD_REVF, RIGIDBOARD_V2 & SCOOVO_X9H + * M909, M910 & LCD - only PRINTRBOARD_REVF & RIGIDBOARD_V2 + */ +//#define PWM_MOTOR_CURRENT { 1300, 1300, 1250 } // Values in milliamps +//#define DIGIPOT_MOTOR_CURRENT { 135,135,135,135,135 } // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A) +//#define DAC_MOTOR_CURRENT_DEFAULT { 70, 80, 90, 80 } // Default drive percent - X, Y, Z, E axis + +// Use an I2C based DIGIPOT (e.g., Azteeg X3 Pro) +//#define DIGIPOT_I2C +#if ENABLED(DIGIPOT_I2C) && !defined(DIGIPOT_I2C_ADDRESS_A) + /** + * Common slave addresses: + * + * A (A shifted) B (B shifted) IC + * Smoothie 0x2C (0x58) 0x2D (0x5A) MCP4451 + * AZTEEG_X3_PRO 0x2C (0x58) 0x2E (0x5C) MCP4451 + * AZTEEG_X5_MINI 0x2C (0x58) 0x2E (0x5C) MCP4451 + * AZTEEG_X5_MINI_WIFI 0x58 0x5C MCP4451 + * MIGHTYBOARD_REVE 0x2F (0x5E) MCP4018 + */ + #define DIGIPOT_I2C_ADDRESS_A 0x2C // unshifted slave address for first DIGIPOT + #define DIGIPOT_I2C_ADDRESS_B 0x2D // unshifted slave address for second DIGIPOT +#endif + +//#define DIGIPOT_MCP4018 // Requires library from https://github.com/stawel/SlowSoftI2CMaster +#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8 MKS SBASE: 5 +// Actual motor currents in Amps. The number of entries must match DIGIPOT_I2C_NUM_CHANNELS. +// These correspond to the physical drivers, so be mindful if the order is changed. +#define DIGIPOT_I2C_MOTOR_CURRENTS { 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0 } // AZTEEG_X3_PRO + +//=========================================================================== +//=============================Additional Features=========================== +//=========================================================================== + +// @section lcd + +// Change values more rapidly when the encoder is rotated faster +#define ENCODER_RATE_MULTIPLIER +#if ENABLED(ENCODER_RATE_MULTIPLIER) + #define ENCODER_10X_STEPS_PER_SEC 75 // (steps/s) Encoder rate for 10x speed + #define ENCODER_100X_STEPS_PER_SEC 160 // (steps/s) Encoder rate for 100x speed +#endif + +// Play a beep when the feedrate is changed from the Status Screen +//#define BEEP_ON_FEEDRATE_CHANGE +#if ENABLED(BEEP_ON_FEEDRATE_CHANGE) + #define FEEDRATE_CHANGE_BEEP_DURATION 10 + #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 +#endif + +// Include a page of printer information in the LCD Main Menu +#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif + +// Scroll a longer status message into view +#define STATUS_MESSAGE_SCROLLING + +// On the Info Screen, display XY with one decimal place when possible +//#define LCD_DECIMAL_SMALL_XY + +// The timeout (in ms) to return to the status screen from sub-menus +//#define LCD_TIMEOUT_TO_STATUS 15000 + +// Add an 'M73' G-code to set the current percentage +#define LCD_SET_PROGRESS_MANUALLY + +#if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS + //#define LCD_PROGRESS_BAR // Show a progress bar on HD44780 LCDs for SD printing + #if ENABLED(LCD_PROGRESS_BAR) + #define PROGRESS_BAR_BAR_TIME 2000 // (ms) Amount of time to show the bar + #define PROGRESS_BAR_MSG_TIME 3000 // (ms) Amount of time to show the status message + #define PROGRESS_MSG_EXPIRE 0 // (ms) Amount of time to retain the status message (0=forever) + //#define PROGRESS_MSG_ONCE // Show the message for MSG_TIME then clear it + //#define LCD_PROGRESS_BAR_TEST // Add a menu item to test the progress bar + #endif +#endif + +/** + * LED Control Menu + * Enable this feature to add LED Control to the LCD menu + */ +//#define LED_CONTROL_MENU +#if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif +#endif // LED_CONTROL_MENU + +#if ENABLED(SDSUPPORT) + + // Some RAMPS and other boards don't detect when an SD card is inserted. You can work + // around this by connecting a push button or single throw switch to the pin defined + // as SD_DETECT_PIN in your board's pins definitions. + // This setting should be disabled unless you are using a push button, pulling the pin to ground. + // Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER). + #define SD_DETECT_INVERTED + + #define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished + #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place. + + // Reverse SD sort to show "more recent" files first, according to the card's FAT. + // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended. + #define SDCARD_RATHERRECENTFIRST + + #define SD_MENU_CONFIRM_START // Confirm the selected SD file before printing + + //#define MENU_ADDAUTOSTART // Add a menu option to run auto#.g files + + #define EVENT_GCODE_SD_STOP "G28XY" // G-code to run on Stop Print (e.g., "G28XY" or "G27") + + /** + * Continue after Power-Loss (Creality3D) + * + * Store the current state to the SD Card at the start of each layer + * during SD printing. If the recovery file is found at boot time, present + * an option on the LCD screen to continue the print from the last-known + * point in the file. + */ + //#define POWER_LOSS_RECOVERY + #if ENABLED(POWER_LOSS_RECOVERY) + //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume + //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. + + // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, + // especially with "vase mode" printing. Set too high and vases cannot be continued. + #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + #endif + + /** + * Sort SD file listings in alphabetical order. + * + * With this option enabled, items on SD cards will be sorted + * by name for easier navigation. + * + * By default... + * + * - Use the slowest -but safest- method for sorting. + * - Folders are sorted to the top. + * - The sort key is statically allocated. + * - No added G-code (M34) support. + * - 40 item sorting limit. (Items after the first 40 are unsorted.) + * + * SD sorting uses static allocation (as set by SDSORT_LIMIT), allowing the + * compiler to calculate the worst-case usage and throw an error if the SRAM + * limit is exceeded. + * + * - SDSORT_USES_RAM provides faster sorting via a static directory buffer. + * - SDSORT_USES_STACK does the same, but uses a local stack-based buffer. + * - SDSORT_CACHE_NAMES will retain the sorted file listing in RAM. (Expensive!) + * - SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible. (Use with caution!) + */ + #define SDCARD_SORT_ALPHA + + // SD Card Sorting options + #if ENABLED(SDCARD_SORT_ALPHA) + #define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). Costs 27 bytes each. + #define FOLDER_SORTING -1 // -1=above 0=none 1=below + #define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 g-code. + #define SDSORT_USES_RAM false // Pre-allocate a static array for faster pre-sorting. + #define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.) + #define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option. + #define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use! + #define SDSORT_CACHE_VFATS 2 // Maximum number of 13-byte VFAT entries to use for sorting. + // Note: Only affects SCROLL_LONG_FILENAMES with SDSORT_CACHE_NAMES but not SDSORT_DYNAMIC_RAM. + #endif + + // This allows hosts to request long names for files and folders with M33 + #define LONG_FILENAME_HOST_SUPPORT + + // Enable this option to scroll long filenames in the SD card menu + #define SCROLL_LONG_FILENAMES + + // Leave the heaters on after Stop Print (not recommended!) + //#define SD_ABORT_NO_COOLDOWN + + /** + * This option allows you to abort SD printing when any endstop is triggered. + * This feature must be enabled with "M540 S1" or from the LCD menu. + * To have any effect, endstops must be enabled during SD printing. + */ + //#define SD_ABORT_ON_ENDSTOP_HIT + + /** + * This option makes it easier to print the same SD Card file again. + * On print completion the LCD Menu will open with the file selected. + * You can just click to start the print, or navigate elsewhere. + */ + //#define SD_REPRINT_LAST_SELECTED_FILE + + /** + * Auto-report SdCard status with M27 S + */ + //#define AUTO_REPORT_SD_STATUS + + /** + * Support for USB thumb drives using an Arduino USB Host Shield or + * equivalent MAX3421E breakout board. The USB thumb drive will appear + * to Marlin as an SD card. + * + * The MAX3421E must be assigned the same pins as the SD card reader, with + * the following pin mapping: + * + * SCLK, MOSI, MISO --> SCLK, MOSI, MISO + * INT --> SD_DETECT_PIN + * SS --> SDSS + */ + //#define USB_FLASH_DRIVE_SUPPORT + #if ENABLED(USB_FLASH_DRIVE_SUPPORT) + #define USB_CS_PIN SDSS + #define USB_INTR_PIN SD_DETECT_PIN + #endif + + /** + * When using a bootloader that supports SD-Firmware-Flashing, + * add a menu item to activate SD-FW-Update on the next reboot. + * + * Requires ATMEGA2560 (Arduino Mega) + * + * Tested with this bootloader: + * https://github.com/FleetProbe/MicroBridge-Arduino-ATMega2560 + */ + //#define SD_FIRMWARE_UPDATE + #if ENABLED(SD_FIRMWARE_UPDATE) + #define SD_FIRMWARE_UPDATE_EEPROM_ADDR 0x1FF + #define SD_FIRMWARE_UPDATE_ACTIVE_VALUE 0xF0 + #define SD_FIRMWARE_UPDATE_INACTIVE_VALUE 0xFF + #endif + + // Add an optimized binary file transfer mode, initiated with 'M28 B1' + //#define BINARY_FILE_TRANSFER + + #if HAS_SDCARD_CONNECTION + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD + #endif + +#endif // SDSUPPORT + +/** + * By default an onboard SD card reader may be shared as a USB mass- + * storage device. This option hides the SD card from the host PC. + */ +//#define NO_SD_HOST_DRIVE // Disable SD Card access over USB (for security). + +/** + * Additional options for Graphical Displays + * + * Use the optimizations here to improve printing performance, + * which can be adversely affected by graphical display drawing, + * especially when doing several short moves, and when printing + * on DELTA and SCARA machines. + * + * Some of these options may result in the display lagging behind + * controller events, as there is a trade-off between reliable + * printing performance versus fast display updates. + */ +#if HAS_GRAPHICAL_LCD + // Show SD percentage next to the progress bar + //#define DOGM_SD_PERCENT + + // Enable to save many cycles by drawing a hollow frame on the Info Screen + #define XYZ_HOLLOW_FRAME + + // Enable to save many cycles by drawing a hollow frame on Menu Screens + #define MENU_HOLLOW_FRAME + + // A bigger font is available for edit items. Costs 3120 bytes of PROGMEM. + // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. + #define USE_BIG_EDIT_FONT + + // A smaller font may be used on the Info Screen. Costs 2300 bytes of PROGMEM. + // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. + //#define USE_SMALL_INFOFONT + + // Enable this option and reduce the value to optimize screen updates. + // The normal delay is 10µs. Use the lowest value that still gives a reliable display. + //#define DOGM_SPI_DELAY_US 5 + + // Swap the CW/CCW indicators in the graphics overlay + //#define OVERLAY_GFX_REVERSE + + /** + * ST7920-based LCDs can emulate a 16 x 4 character display using + * the ST7920 character-generator for very fast screen updates. + * Enable LIGHTWEIGHT_UI to use this special display mode. + * + * Since LIGHTWEIGHT_UI has limited space, the position and status + * message occupy the same line. Set STATUS_EXPIRE_SECONDS to the + * length of time to display the status message before clearing. + * + * Set STATUS_EXPIRE_SECONDS to zero to never clear the status. + * This will prevent position updates from being displayed. + */ + #if ENABLED(U8GLIB_ST7920) + //#define LIGHTWEIGHT_UI + #if ENABLED(LIGHTWEIGHT_UI) + #define STATUS_EXPIRE_SECONDS 20 + #endif + #endif + + /** + * Status (Info) Screen customizations + * These options may affect code size and screen render time. + * Custom status screens can forcibly override these settings. + */ + //#define STATUS_COMBINE_HEATERS // Use combined heater images instead of separate ones + //#define STATUS_HOTEND_NUMBERLESS // Use plain hotend icons instead of numbered ones (with 2+ hotends) + #define STATUS_HOTEND_INVERTED // Show solid nozzle bitmaps when heating (Requires STATUS_HOTEND_ANIM) + #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating + #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating + #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap + //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap + //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames + #define STATUS_HEAT_PERCENT // Show heating in a progress bar + //#define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash) + + // Frivolous Game Options + //#define MARLIN_BRICKOUT + //#define MARLIN_INVADERS + //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu + +#endif // HAS_GRAPHICAL_LCD + +// @section safety + +/** + * The watchdog hardware timer will do a reset and disable all outputs + * if the firmware gets too overloaded to read the temperature sensors. + * + * If you find that watchdog reboot causes your AVR board to hang forever, + * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO. + * NOTE: This method is less reliable as it can only catch hangups while + * interrupts are enabled. + */ +#define USE_WATCHDOG +#if ENABLED(USE_WATCHDOG) + //#define WATCHDOG_RESET_MANUAL +#endif + +// @section lcd + +/** + * Babystepping enables movement of the axes by tiny increments without changing + * the current position values. This feature is used primarily to adjust the Z + * axis in the first layer of a print in real-time. + * + * Warning: Does not respect endstops! + */ +#define BABYSTEPPING +#if ENABLED(BABYSTEPPING) + //#define BABYSTEP_WITHOUT_HOMING + //#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA! + #define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way + #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion. + + #define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping. + #if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING) + #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds. + // Note: Extra time may be added to mitigate controller latency. + //#define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement). + //#define MOVE_Z_WHEN_IDLE // Jump to the move Z menu on doubleclick when printer is idle. + #if ENABLED(MOVE_Z_WHEN_IDLE) + #define MOVE_Z_IDLE_MULTIPLICATOR 1 // Multiply 1mm by this factor for the move step size. + #endif + #endif + + //#define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28 + + //#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping + #if ENABLED(BABYSTEP_ZPROBE_OFFSET) + //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets + //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor + #endif +#endif + +// @section extruder + +/** + * Linear Pressure Control v1.5 + * + * Assumption: advance [steps] = k * (delta velocity [steps/s]) + * K=0 means advance disabled. + * + * NOTE: K values for LIN_ADVANCE 1.5 differ from earlier versions! + * + * Set K around 0.22 for 3mm PLA Direct Drive with ~6.5cm between the drive gear and heatbreak. + * Larger K values will be needed for flexible filament and greater distances. + * If this algorithm produces a higher speed offset than the extruder can handle (compared to E jerk) + * print acceleration will be reduced during the affected moves to keep within the limit. + * + * See http://marlinfw.org/docs/features/lin_advance.html for full instructions. + * Mention @Sebastianv650 on GitHub to alert the author of any issues. + */ +//#define LIN_ADVANCE +#if ENABLED(LIN_ADVANCE) + //#define EXTRA_LIN_ADVANCE_K // Enable for second linear advance constants + #define LIN_ADVANCE_K 0.22 // Unit: mm compression per 1mm/s extruder speed + //#define LA_DEBUG // If enabled, this will generate debug information output over USB. +#endif + +// @section leveling + +#if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL) + // Override the mesh area if the automatic (max) area is too large + //#define MESH_MIN_X MESH_INSET + //#define MESH_MIN_Y MESH_INSET + //#define MESH_MAX_X X_BED_SIZE - (MESH_INSET) + //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET) +#endif + +/** + * Repeatedly attempt G29 leveling until it succeeds. + * Stop after G29_MAX_RETRIES attempts. + */ +//#define G29_RETRY_AND_RECOVER +#if ENABLED(G29_RETRY_AND_RECOVER) + #define G29_MAX_RETRIES 3 + #define G29_HALT_ON_FAILURE + /** + * Specify the GCODE commands that will be executed when leveling succeeds, + * between attempts, and after the maximum number of retries have been tried. + */ + #define G29_SUCCESS_COMMANDS "M117 Bed leveling done." + #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0" + #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1" + +#endif + +// @section extras + +// +// G2/G3 Arc Support +// +#define ARC_SUPPORT // Disable this feature to save ~3226 bytes +#if ENABLED(ARC_SUPPORT) + #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles + //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes +#endif + +// Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes. +//#define BEZIER_CURVE_SUPPORT + +/** + * G38 Probe Target + * + * This option adds G38.2 and G38.3 (probe towards target) + * and optionally G38.4 and G38.5 (probe away from target). + * Set MULTIPLE_PROBING for G38 to probe more than once. + */ +//#define G38_PROBE_TARGET +#if ENABLED(G38_PROBE_TARGET) + //#define G38_PROBE_AWAY // Include G38.4 and G38.5 to probe away from target + #define G38_MINIMUM_MOVE 0.0275 // (mm) Minimum distance that will produce a move. +#endif + +// Moves (or segments) with fewer steps than this will be joined with the next move +#define MIN_STEPS_PER_SEGMENT 6 + +/** + * Minimum delay after setting the stepper DIR (in ns) + * 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire) + * 20 : Minimum for TMC2xxx drivers + * 200 : Minimum for A4988 drivers + * 400 : Minimum for A5984 drivers + * 500 : Minimum for LV8729 drivers (guess, no info in datasheet) + * 650 : Minimum for DRV8825 drivers + * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet) + * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet) + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MINIMUM_STEPPER_DIR_DELAY 650 + +/** + * Minimum stepper driver pulse width (in µs) + * 0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers + * 0 : Minimum 500ns for LV8729, adjusted in stepper.h + * 1 : Minimum for A4988 and A5984 stepper drivers + * 2 : Minimum for DRV8825 stepper drivers + * 3 : Minimum for TB6600 stepper drivers + * 30 : Minimum for TB6560 stepper drivers + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MINIMUM_STEPPER_PULSE 2 + +/** + * Maximum stepping rate (in Hz) the stepper driver allows + * If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE) + * 500000 : Maximum for A4988 stepper driver + * 400000 : Maximum for TMC2xxx stepper drivers + * 250000 : Maximum for DRV8825 stepper driver + * 200000 : Maximum for LV8729 stepper driver + * 150000 : Maximum for TB6600 stepper driver + * 15000 : Maximum for TB6560 stepper driver + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MAXIMUM_STEPPER_RATE 250000 + +// @section temperature + +// Control heater 0 and heater 1 in parallel. +//#define HEATERS_PARALLEL + +//=========================================================================== +//================================= Buffers ================================= +//=========================================================================== + +// @section hidden + +// The number of linear motions that can be in the plan at any give time. +// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2 (e.g. 8, 16, 32) because shifts and ors are used to do the ring-buffering. +#if ENABLED(SDSUPPORT) + #define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller +#else + #define BLOCK_BUFFER_SIZE 16 // maximize block buffer +#endif + +// @section serial + +// The ASCII buffer for serial input +#define MAX_CMD_SIZE 96 +#define BUFSIZE 4 + +// Transmission to Host Buffer Size +// To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0. +// To buffer a simple "ok" you need 4 bytes. +// For ADVANCED_OK (M105) you need 32 bytes. +// For debug-echo: 128 bytes for the optimal speed. +// Other output doesn't need to be that speedy. +// :[0, 2, 4, 8, 16, 32, 64, 128, 256] +#define TX_BUFFER_SIZE 0 + +// Host Receive Buffer Size +// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough. +// To use flow control, set this buffer size to at least 1024 bytes. +// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048] +//#define RX_BUFFER_SIZE 1024 + +#if RX_BUFFER_SIZE >= 1024 + // Enable to have the controller send XON/XOFF control characters to + // the host to signal the RX buffer is becoming full. + //#define SERIAL_XON_XOFF +#endif + +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + +#if ENABLED(SDSUPPORT) + // Enable this option to collect and display the maximum + // RX queue usage after transferring a file to SD. + //#define SERIAL_STATS_MAX_RX_QUEUED + + // Enable this option to collect and display the number + // of dropped bytes after a file transfer to SD. + //#define SERIAL_STATS_DROPPED_RX +#endif + +// Enable an emergency-command parser to intercept certain commands as they +// enter the serial receive buffer, so they cannot be blocked. +// Currently handles M108, M112, M410 +// Does not work on boards using AT90USB (USBCON) processors! +//#define EMERGENCY_PARSER + +// Bad Serial-connections can miss a received command by sending an 'ok' +// Therefore some clients abort after 30 seconds in a timeout. +// Some other clients start sending commands while receiving a 'wait'. +// This "wait" is only sent when the buffer is empty. 1 second is a good value here. +//#define NO_TIMEOUTS 1000 // Milliseconds + +// Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary. +//#define ADVANCED_OK + +// Printrun may have trouble receiving long strings all at once. +// This option inserts short delays between lines of serial output. +#define SERIAL_OVERRUN_PROTECTION + +// @section extras + +/** + * Extra Fan Speed + * Adds a secondary fan speed for each print-cooling fan. + * 'M106 P T3-255' : Set a secondary speed for + * 'M106 P T2' : Use the set secondary speed + * 'M106 P T1' : Restore the previous fan speed + */ +//#define EXTRA_FAN_SPEED + +/** + * Firmware-based and LCD-controlled retract + * + * Add G10 / G11 commands for automatic firmware-based retract / recover. + * Use M207 and M208 to define parameters for retract / recover. + * + * Use M209 to enable or disable auto-retract. + * With auto-retract enabled, all G1 E moves within the set range + * will be converted to firmware-based retract/recover moves. + * + * Be sure to turn off auto-retract during filament change. + * + * Note that M207 / M208 / M209 settings are saved to EEPROM. + * + */ +//#define FWRETRACT +#if ENABLED(FWRETRACT) + #define FWRETRACT_AUTORETRACT // costs ~500 bytes of PROGMEM + #if ENABLED(FWRETRACT_AUTORETRACT) + #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over + #define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion + #endif + #define RETRACT_LENGTH 3 // Default retract length (positive mm) + #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change + #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) + #define RETRACT_ZRAISE 0 // Default retract Z-raise (mm) + #define RETRACT_RECOVER_LENGTH 0 // Default additional recover length (mm, added to retract length when recovering) + #define RETRACT_RECOVER_LENGTH_SWAP 0 // Default additional swap recover length (mm, added to retract length when recovering from extruder change) + #define RETRACT_RECOVER_FEEDRATE 8 // Default feedrate for recovering from retraction (mm/s) + #define RETRACT_RECOVER_FEEDRATE_SWAP 8 // Default feedrate for recovering from swap retraction (mm/s) + #if ENABLED(MIXING_EXTRUDER) + //#define RETRACT_SYNC_MIXING // Retract and restore all mixing steppers simultaneously + #endif +#endif + +/** + * Universal tool change settings. + * Applies to all types of extruders except where explicitly noted. + */ +#if EXTRUDERS > 1 + // Z raise distance for tool-change, as needed for some extruders + #define TOOLCHANGE_ZRAISE 2 // (mm) + //#define TOOLCHANGE_NO_RETURN // Never return to the previous position on tool-change + + // Retract and prime filament on tool-change + //#define TOOLCHANGE_FILAMENT_SWAP + #if ENABLED(TOOLCHANGE_FILAMENT_SWAP) + #define TOOLCHANGE_FIL_SWAP_LENGTH 12 // (mm) + #define TOOLCHANGE_FIL_EXTRA_PRIME 2 // (mm) + #define TOOLCHANGE_FIL_SWAP_RETRACT_SPEED 3600 // (mm/m) + #define TOOLCHANGE_FIL_SWAP_PRIME_SPEED 3600 // (mm/m) + #endif + + /** + * Position to park head during tool change. + * Doesn't apply to SWITCHING_TOOLHEAD, DUAL_X_CARRIAGE, or PARKING_EXTRUDER + */ + //#define TOOLCHANGE_PARK + #if ENABLED(TOOLCHANGE_PARK) + #define TOOLCHANGE_PARK_XY { X_MIN_POS + 10, Y_MIN_POS + 10 } + #define TOOLCHANGE_PARK_XY_FEEDRATE 6000 // (mm/m) + #endif +#endif + +/** + * Advanced Pause + * Experimental feature for filament change support and for parking the nozzle when paused. + * Adds the GCode M600 for initiating filament change. + * If PARK_HEAD_ON_PAUSE enabled, adds the GCode M125 to pause printing and park the nozzle. + * + * Requires an LCD display. + * Requires NOZZLE_PARK_FEATURE. + * This feature is required for the default FILAMENT_RUNOUT_SCRIPT. + */ +#define ADVANCED_PAUSE_FEATURE +#if ENABLED(ADVANCED_PAUSE_FEATURE) + #define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate. + #define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract. + // This short retract is done immediately, before parking the nozzle. + #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast. + #define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. + #define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload. + // For Bowden, the full length of the tube and nozzle. + // For direct drive, the full length of the nozzle. + // Set to 0 for manual unloading. + #define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load. + #define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material. + // 0 to disable start loading and skip to fast load only + #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast. + #define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. + #define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle. + // For Bowden, the full length of the tube and nozzle. + // For direct drive, the full length of the nozzle. + //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted. + #define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate. + #define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading. + // Set to 0 for manual extrusion. + // Filament can be extruded repeatedly from the Filament Change menu + // until extrusion is consistent, and to purge old filament. + #define ADVANCED_PAUSE_RESUME_PRIME 0 // (mm) Extra distance to prime nozzle after returning from park. + //#define ADVANCED_PAUSE_FANS_PAUSE // Turn off print-cooling fans while the machine is paused. + + // Filament Unload does a Retract, Delay, and Purge first: + #define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length. + #define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract. + #define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged. + + #define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety. + #define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed. + #define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change. + + //#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change. + //#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change + + //#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu. + //#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302) +#endif + +// @section tmc + +/** + * TMC26X Stepper Driver options + * + * The TMC26XStepper library is required for this stepper driver. + * https://github.com/trinamic/TMC26XStepper + */ +#if HAS_DRIVER(TMC26X) + + #if AXIS_DRIVER_TYPE_X(TMC26X) + #define X_MAX_CURRENT 1000 // (mA) + #define X_SENSE_RESISTOR 91 // (mOhms) + #define X_MICROSTEPS 16 // Number of microsteps + #endif + + #if AXIS_DRIVER_TYPE_X2(TMC26X) + #define X2_MAX_CURRENT 1000 + #define X2_SENSE_RESISTOR 91 + #define X2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Y(TMC26X) + #define Y_MAX_CURRENT 1000 + #define Y_SENSE_RESISTOR 91 + #define Y_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Y2(TMC26X) + #define Y2_MAX_CURRENT 1000 + #define Y2_SENSE_RESISTOR 91 + #define Y2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z(TMC26X) + #define Z_MAX_CURRENT 1000 + #define Z_SENSE_RESISTOR 91 + #define Z_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z2(TMC26X) + #define Z2_MAX_CURRENT 1000 + #define Z2_SENSE_RESISTOR 91 + #define Z2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z3(TMC26X) + #define Z3_MAX_CURRENT 1000 + #define Z3_SENSE_RESISTOR 91 + #define Z3_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E0(TMC26X) + #define E0_MAX_CURRENT 1000 + #define E0_SENSE_RESISTOR 91 + #define E0_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E1(TMC26X) + #define E1_MAX_CURRENT 1000 + #define E1_SENSE_RESISTOR 91 + #define E1_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E2(TMC26X) + #define E2_MAX_CURRENT 1000 + #define E2_SENSE_RESISTOR 91 + #define E2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E3(TMC26X) + #define E3_MAX_CURRENT 1000 + #define E3_SENSE_RESISTOR 91 + #define E3_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E4(TMC26X) + #define E4_MAX_CURRENT 1000 + #define E4_SENSE_RESISTOR 91 + #define E4_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E5(TMC26X) + #define E5_MAX_CURRENT 1000 + #define E5_SENSE_RESISTOR 91 + #define E5_MICROSTEPS 16 + #endif + +#endif // TMC26X + +// @section tmc_smart + +/** + * To use TMC2130, TMC2160, TMC2660, TMC5130, TMC5160 stepper drivers in SPI mode + * connect your SPI pins to the hardware SPI interface on your board and define + * the required CS pins in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 + * pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.). + * You may also use software SPI if you wish to use general purpose IO pins. + * + * To use TMC2208 stepper UART-configurable stepper drivers connect #_SERIAL_TX_PIN + * to the driver side PDN_UART pin with a 1K resistor. + * To use the reading capabilities, also connect #_SERIAL_RX_PIN to PDN_UART without + * a resistor. + * The drivers can also be used with hardware serial. + * + * TMCStepper library is required to use TMC stepper drivers. + * https://github.com/teemuatlut/TMCStepper + */ +#if HAS_TRINAMIC + + #define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current + #define INTERPOLATE true // Interpolate X/Y/Z_MICROSTEPS to 256 + + #if AXIS_IS_TMC(X) + #define X_CURRENT 800 // (mA) RMS current. Multiply by 1.414 for peak current. + #define X_MICROSTEPS 16 // 0..256 + #define X_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(X2) + #define X2_CURRENT 800 + #define X2_MICROSTEPS 16 + #define X2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Y) + #define Y_CURRENT 800 + #define Y_MICROSTEPS 16 + #define Y_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Y2) + #define Y2_CURRENT 800 + #define Y2_MICROSTEPS 16 + #define Y2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Z) + #define Z_CURRENT 800 + #define Z_MICROSTEPS 16 + #define Z_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Z2) + #define Z2_CURRENT 800 + #define Z2_MICROSTEPS 16 + #define Z2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Z3) + #define Z3_CURRENT 800 + #define Z3_MICROSTEPS 16 + #define Z3_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E0) + #define E0_CURRENT 800 + #define E0_MICROSTEPS 16 + #define E0_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E1) + #define E1_CURRENT 800 + #define E1_MICROSTEPS 16 + #define E1_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E2) + #define E2_CURRENT 800 + #define E2_MICROSTEPS 16 + #define E2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E3) + #define E3_CURRENT 800 + #define E3_MICROSTEPS 16 + #define E3_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E4) + #define E4_CURRENT 800 + #define E4_MICROSTEPS 16 + #define E4_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E5) + #define E5_CURRENT 800 + #define E5_MICROSTEPS 16 + #define E5_RSENSE 0.11 + #endif + + /** + * Override default SPI pins for TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160 drivers here. + * The default pins can be found in your board's pins file. + */ + //#define X_CS_PIN -1 + //#define Y_CS_PIN -1 + //#define Z_CS_PIN -1 + //#define X2_CS_PIN -1 + //#define Y2_CS_PIN -1 + //#define Z2_CS_PIN -1 + //#define Z3_CS_PIN -1 + //#define E0_CS_PIN -1 + //#define E1_CS_PIN -1 + //#define E2_CS_PIN -1 + //#define E3_CS_PIN -1 + //#define E4_CS_PIN -1 + //#define E5_CS_PIN -1 + + /** + * Software option for SPI driven drivers (TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160). + * The default SW SPI pins are defined the respective pins files, + * but you can override or define them here. + */ + //#define TMC_USE_SW_SPI + //#define TMC_SW_MOSI -1 + //#define TMC_SW_MISO -1 + //#define TMC_SW_SCK -1 + + /** + * Four TMC2209 drivers can use the same HW/SW serial port with hardware configured addresses. + * Set the address using jumpers on pins MS1 and MS2. + * Address | MS1 | MS2 + * 0 | LOW | LOW + * 1 | HIGH | LOW + * 2 | LOW | HIGH + * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. + */ + #define X_SLAVE_ADDRESS 0 + #define Y_SLAVE_ADDRESS 0 + #define Z_SLAVE_ADDRESS 0 + #define X2_SLAVE_ADDRESS 0 + #define Y2_SLAVE_ADDRESS 0 + #define Z2_SLAVE_ADDRESS 0 + #define Z3_SLAVE_ADDRESS 0 + #define E0_SLAVE_ADDRESS 0 + #define E1_SLAVE_ADDRESS 0 + #define E2_SLAVE_ADDRESS 0 + #define E3_SLAVE_ADDRESS 0 + #define E4_SLAVE_ADDRESS 0 + #define E5_SLAVE_ADDRESS 0 + + /** + * Software enable + * + * Use for drivers that do not use a dedicated enable pin, but rather handle the same + * function through a communication line such as SPI or UART. + */ + //#define SOFTWARE_DRIVER_ENABLE + + /** + * TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only + * Use Trinamic's ultra quiet stepping mode. + * When disabled, Marlin will use spreadCycle stepping mode. + */ + #define STEALTHCHOP_XY + #define STEALTHCHOP_Z + #define STEALTHCHOP_E + + /** + * Optimize spreadCycle chopper parameters by using predefined parameter sets + * or with the help of an example included in the library. + * Provided parameter sets are + * CHOPPER_DEFAULT_12V + * CHOPPER_DEFAULT_19V + * CHOPPER_DEFAULT_24V + * CHOPPER_DEFAULT_36V + * CHOPPER_PRUSAMK3_24V // Imported parameters from the official Prusa firmware for MK3 (24V) + * CHOPPER_MARLIN_119 // Old defaults from Marlin v1.1.9 + * + * Define you own with + * { , , hysteresis_start[1..8] } + */ + #define CHOPPER_TIMING CHOPPER_DEFAULT_24V + + /** + * Monitor Trinamic drivers for error conditions, + * like overtemperature and short to ground. + * In the case of overtemperature Marlin can decrease the driver current until error condition clears. + * Other detected conditions can be used to stop the current print. + * Relevant g-codes: + * M906 - Set or get motor current in milliamps using axis codes X, Y, Z, E. Report values if no axis codes given. + * M911 - Report stepper driver overtemperature pre-warn condition. + * M912 - Clear stepper driver overtemperature pre-warn condition flag. + * M122 - Report driver parameters (Requires TMC_DEBUG) + */ + //#define MONITOR_DRIVER_STATUS + + #if ENABLED(MONITOR_DRIVER_STATUS) + #define CURRENT_STEP_DOWN 50 // [mA] + #define REPORT_CURRENT_CHANGE + #define STOP_ON_ERROR + #endif + + /** + * TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only + * The driver will switch to spreadCycle when stepper speed is over HYBRID_THRESHOLD. + * This mode allows for faster movements at the expense of higher noise levels. + * STEALTHCHOP_(XY|Z|E) must be enabled to use HYBRID_THRESHOLD. + * M913 X/Y/Z/E to live tune the setting + */ + //#define HYBRID_THRESHOLD + + #define X_HYBRID_THRESHOLD 100 // [mm/s] + #define X2_HYBRID_THRESHOLD 100 + #define Y_HYBRID_THRESHOLD 100 + #define Y2_HYBRID_THRESHOLD 100 + #define Z_HYBRID_THRESHOLD 3 + #define Z2_HYBRID_THRESHOLD 3 + #define Z3_HYBRID_THRESHOLD 3 + #define E0_HYBRID_THRESHOLD 30 + #define E1_HYBRID_THRESHOLD 30 + #define E2_HYBRID_THRESHOLD 30 + #define E3_HYBRID_THRESHOLD 30 + #define E4_HYBRID_THRESHOLD 30 + #define E5_HYBRID_THRESHOLD 30 + + /** + * TMC2130, TMC2160, TMC2209, TMC2660, TMC5130, and TMC5160 only + * Use StallGuard2 to sense an obstacle and trigger an endstop. + * Connect the stepper driver's DIAG1 pin to the X/Y endstop pin. + * X, Y, and Z homing will always be done in spreadCycle mode. + * + * X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity. + * Higher values make the system LESS sensitive. + * Lower value make the system MORE sensitive. + * Too low values can lead to false positives, while too high values will collide the axis without triggering. + * It is advised to set X/Y/Z_HOME_BUMP_MM to 0. + * M914 X/Y/Z to live tune the setting + */ + //#define SENSORLESS_HOMING // StallGuard capable drivers only + + /** + * Use StallGuard2 to probe the bed with the nozzle. + * + * CAUTION: This could cause damage to machines that use a lead screw or threaded rod + * to move the Z axis. Take extreme care when attempting to enable this feature. + */ + //#define SENSORLESS_PROBING // StallGuard capable drivers only + + #if EITHER(SENSORLESS_HOMING, SENSORLESS_PROBING) + // TMC2209: 0...255. TMC2130: -64...63 + #define X_STALL_SENSITIVITY 8 + #define Y_STALL_SENSITIVITY 8 + //#define Z_STALL_SENSITIVITY 8 + #endif + + /** + * Beta feature! + * Create a 50/50 square wave step pulse optimal for stepper drivers. + */ + //#define SQUARE_WAVE_STEPPING + + /** + * Enable M122 debugging command for TMC stepper drivers. + * M122 S0/1 will enable continous reporting. + */ + //#define TMC_DEBUG + + /** + * You can set your own advanced settings by filling in predefined functions. + * A list of available functions can be found on the library github page + * https://github.com/teemuatlut/TMCStepper + * + * Example: + * #define TMC_ADV() { \ + * stepperX.diag0_temp_prewarn(1); \ + * stepperY.interpolate(0); \ + * } + */ + #define TMC_ADV() { } + +#endif // HAS_TRINAMIC + +// @section L6470 + +/** + * L6470 Stepper Driver options + * + * Arduino-L6470 library (0.7.0 or higher) is required for this stepper driver. + * https://github.com/ameyer/Arduino-L6470 + * + * Requires the following to be defined in your pins_YOUR_BOARD file + * L6470_CHAIN_SCK_PIN + * L6470_CHAIN_MISO_PIN + * L6470_CHAIN_MOSI_PIN + * L6470_CHAIN_SS_PIN + * L6470_RESET_CHAIN_PIN (optional) + */ +#if HAS_DRIVER(L6470) + + //#define L6470_CHITCHAT // Display additional status info + + #if AXIS_DRIVER_TYPE_X(L6470) + #define X_MICROSTEPS 128 // Number of microsteps (VALID: 1, 2, 4, 8, 16, 32, 128) + #define X_OVERCURRENT 2000 // (mA) Current where the driver detects an over current (VALID: 375 x (1 - 16) - 6A max - rounds down) + #define X_STALLCURRENT 1500 // (mA) Current where the driver detects a stall (VALID: 31.25 * (1-128) - 4A max - rounds down) + #define X_MAX_VOLTAGE 127 // 0-255, Maximum effective voltage seen by stepper + #define X_CHAIN_POS 0 // Position in SPI chain, 0=Not in chain, 1=Nearest MOSI + #endif + + #if AXIS_DRIVER_TYPE_X2(L6470) + #define X2_MICROSTEPS 128 + #define X2_OVERCURRENT 2000 + #define X2_STALLCURRENT 1500 + #define X2_MAX_VOLTAGE 127 + #define X2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Y(L6470) + #define Y_MICROSTEPS 128 + #define Y_OVERCURRENT 2000 + #define Y_STALLCURRENT 1500 + #define Y_MAX_VOLTAGE 127 + #define Y_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Y2(L6470) + #define Y2_MICROSTEPS 128 + #define Y2_OVERCURRENT 2000 + #define Y2_STALLCURRENT 1500 + #define Y2_MAX_VOLTAGE 127 + #define Y2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Z(L6470) + #define Z_MICROSTEPS 128 + #define Z_OVERCURRENT 2000 + #define Z_STALLCURRENT 1500 + #define Z_MAX_VOLTAGE 127 + #define Z_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Z2(L6470) + #define Z2_MICROSTEPS 128 + #define Z2_OVERCURRENT 2000 + #define Z2_STALLCURRENT 1500 + #define Z2_MAX_VOLTAGE 127 + #define Z2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Z3(L6470) + #define Z3_MICROSTEPS 128 + #define Z3_OVERCURRENT 2000 + #define Z3_STALLCURRENT 1500 + #define Z3_MAX_VOLTAGE 127 + #define Z3_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E0(L6470) + #define E0_MICROSTEPS 128 + #define E0_OVERCURRENT 2000 + #define E0_STALLCURRENT 1500 + #define E0_MAX_VOLTAGE 127 + #define E0_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E1(L6470) + #define E1_MICROSTEPS 128 + #define E1_OVERCURRENT 2000 + #define E1_STALLCURRENT 1500 + #define E1_MAX_VOLTAGE 127 + #define E1_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E2(L6470) + #define E2_MICROSTEPS 128 + #define E2_OVERCURRENT 2000 + #define E2_STALLCURRENT 1500 + #define E2_MAX_VOLTAGE 127 + #define E2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E3(L6470) + #define E3_MICROSTEPS 128 + #define E3_OVERCURRENT 2000 + #define E3_STALLCURRENT 1500 + #define E3_MAX_VOLTAGE 127 + #define E3_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E4(L6470) + #define E4_MICROSTEPS 128 + #define E4_OVERCURRENT 2000 + #define E4_STALLCURRENT 1500 + #define E4_MAX_VOLTAGE 127 + #define E4_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E5(L6470) + #define E5_MICROSTEPS 128 + #define E5_OVERCURRENT 2000 + #define E5_STALLCURRENT 1500 + #define E5_MAX_VOLTAGE 127 + #define E5_CHAIN_POS 0 + #endif + + /** + * Monitor L6470 drivers for error conditions like over temperature and over current. + * In the case of over temperature Marlin can decrease the drive until the error condition clears. + * Other detected conditions can be used to stop the current print. + * Relevant g-codes: + * M906 - I1/2/3/4/5 Set or get motor drive level using axis codes X, Y, Z, E. Report values if no axis codes given. + * I not present or I0 or I1 - X, Y, Z or E0 + * I2 - X2, Y2, Z2 or E1 + * I3 - Z3 or E3 + * I4 - E4 + * I5 - E5 + * M916 - Increase drive level until get thermal warning + * M917 - Find minimum current thresholds + * M918 - Increase speed until max or error + * M122 S0/1 - Report driver parameters + */ + //#define MONITOR_L6470_DRIVER_STATUS + + #if ENABLED(MONITOR_L6470_DRIVER_STATUS) + #define KVAL_HOLD_STEP_DOWN 1 + //#define L6470_STOP_ON_ERROR + #endif + +#endif // L6470 + +/** + * TWI/I2C BUS + * + * This feature is an EXPERIMENTAL feature so it shall not be used on production + * machines. Enabling this will allow you to send and receive I2C data from slave + * devices on the bus. + * + * ; Example #1 + * ; This macro send the string "Marlin" to the slave device with address 0x63 (99) + * ; It uses multiple M260 commands with one B arg + * M260 A99 ; Target slave address + * M260 B77 ; M + * M260 B97 ; a + * M260 B114 ; r + * M260 B108 ; l + * M260 B105 ; i + * M260 B110 ; n + * M260 S1 ; Send the current buffer + * + * ; Example #2 + * ; Request 6 bytes from slave device with address 0x63 (99) + * M261 A99 B5 + * + * ; Example #3 + * ; Example serial output of a M261 request + * echo:i2c-reply: from:99 bytes:5 data:hello + */ + +// @section i2cbus + +//#define EXPERIMENTAL_I2CBUS +#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave + +// @section extras + +/** + * Photo G-code + * Add the M240 G-code to take a photo. + * The photo can be triggered by a digital pin or a physical movement. + */ +//#define PHOTO_GCODE +#if ENABLED(PHOTO_GCODE) + // A position to move to (and raise Z) before taking the photo + //#define PHOTO_POSITION { X_MAX_POS - 5, Y_MAX_POS, 0 } // { xpos, ypos, zraise } (M240 X Y Z) + //#define PHOTO_DELAY_MS 100 // (ms) Duration to pause before moving back (M240 P) + //#define PHOTO_RETRACT_MM 6.5 // (mm) E retract/recover for the photo move (M240 R S) + + // Canon RC-1 or homebrew digital camera trigger + // Data from: http://www.doc-diy.net/photo/rc-1_hacked/ + //#define PHOTOGRAPH_PIN 23 + + // Canon Hack Development Kit + // http://captain-slow.dk/2014/03/09/3d-printing-timelapses/ + //#define CHDK_PIN 4 + + // Optional second move with delay to trigger the camera shutter + //#define PHOTO_SWITCH_POSITION { X_MAX_POS, Y_MAX_POS } // { xpos, ypos } (M240 I J) + + // Duration to hold the switch or keep CHDK_PIN high + //#define PHOTO_SWITCH_MS 50 // (ms) (M240 D) +#endif + +/** + * Spindle & Laser control + * + * Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and + * to set spindle speed, spindle direction, and laser power. + * + * SuperPid is a router/spindle speed controller used in the CNC milling community. + * Marlin can be used to turn the spindle on and off. It can also be used to set + * the spindle speed from 5,000 to 30,000 RPM. + * + * You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V + * hardware PWM pin for the speed control and a pin for the rotation direction. + * + * See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details. + */ +//#define SPINDLE_FEATURE +//#define LASER_FEATURE +#if EITHER(SPINDLE_FEATURE, LASER_FEATURE) + #define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH + #define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power + #define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower + #define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power + #define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop + + #if ENABLED(SPINDLE_FEATURE) + //#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction + #define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction + #define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed + + /** + * The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power + * + * SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT + * where PWM duty cycle varies from 0 to 255 + * + * set the following for your controller (ALL MUST BE SET) + */ + #define SPEED_POWER_SLOPE 118.4 + #define SPEED_POWER_INTERCEPT 0 + #define SPEED_POWER_MIN 5000 + #define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM + #else + #define SPEED_POWER_SLOPE 0.3922 + #define SPEED_POWER_INTERCEPT 0 + #define SPEED_POWER_MIN 10 + #define SPEED_POWER_MAX 100 // 0-100% + #endif +#endif + +/** + * Coolant Control + * + * Add the M7, M8, and M9 commands to turn mist or flood coolant on and off. + * + * Note: COOLANT_MIST_PIN and/or COOLANT_FLOOD_PIN must also be defined. + */ +//#define COOLANT_CONTROL +#if ENABLED(COOLANT_CONTROL) + #define COOLANT_MIST // Enable if mist coolant is present + #define COOLANT_FLOOD // Enable if flood coolant is present + #define COOLANT_MIST_INVERT false // Set "true" if the on/off function is reversed + #define COOLANT_FLOOD_INVERT false // Set "true" if the on/off function is reversed +#endif + +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define FILWIDTH_ERROR_MARGIN 1.0 // (mm) If a measurement differs too much from nominal width ignore it + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + +/** + * CNC Coordinate Systems + * + * Enables G53 and G54-G59.3 commands to select coordinate systems + * and G92.1 to reset the workspace to native machine space. + */ +//#define CNC_COORDINATE_SYSTEMS + +/** + * Auto-report temperatures with M155 S + */ +#define AUTO_REPORT_TEMPERATURES + +/** + * Include capabilities in M115 output + */ +#define EXTENDED_CAPABILITIES_REPORT + +/** + * Disable all Volumetric extrusion options + */ +//#define NO_VOLUMETRICS + +#if DISABLED(NO_VOLUMETRICS) + /** + * Volumetric extrusion default state + * Activate to make volumetric extrusion the default method, + * with DEFAULT_NOMINAL_FILAMENT_DIA as the default diameter. + * + * M200 D0 to disable, M200 Dn to set a new diameter. + */ + //#define VOLUMETRIC_DEFAULT_ON +#endif + +/** + * Enable this option for a leaner build of Marlin that removes all + * workspace offsets, simplifying coordinate transformations, leveling, etc. + * + * - M206 and M428 are disabled. + * - G92 will revert to its behavior from Marlin 1.0. + */ +//#define NO_WORKSPACE_OFFSETS + +/** + * Set the number of proportional font spaces required to fill up a typical character space. + * This can help to better align the output of commands like `G29 O` Mesh Output. + * + * For clients that use a fixed-width font (like OctoPrint), leave this set to 1.0. + * Otherwise, adjust according to your client and font. + */ +#define PROPORTIONAL_FONT_RATIO 1.0 + +/** + * Spend 28 bytes of SRAM to optimize the GCode parser + */ +#define FASTER_GCODE_PARSER + +/** + * CNC G-code options + * Support CNC-style G-code dialects used by laser cutters, drawing machine cams, etc. + * Note that G0 feedrates should be used with care for 3D printing (if used at all). + * High feedrates may cause ringing and harm print quality. + */ +//#define PAREN_COMMENTS // Support for parentheses-delimited comments +//#define GCODE_MOTION_MODES // Remember the motion mode (G0 G1 G2 G3 G5 G38.X) and apply for X Y Z E F, etc. + +// Enable and set a (default) feedrate for all G0 moves +//#define G0_FEEDRATE 3000 // (mm/m) +#ifdef G0_FEEDRATE + //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode +#endif + +/** + * G-code Macros + * + * Add G-codes M810-M819 to define and run G-code macros. + * Macros are not saved to EEPROM. + */ +//#define GCODE_MACROS +#if ENABLED(GCODE_MACROS) + #define GCODE_MACROS_SLOTS 5 // Up to 10 may be used + #define GCODE_MACROS_SLOT_SIZE 50 // Maximum length of a single macro +#endif + +/** + * User-defined menu items that execute custom GCode + */ +//#define CUSTOM_USER_MENUS +#if ENABLED(CUSTOM_USER_MENUS) + //#define CUSTOM_USER_MENU_TITLE "Custom Commands" + #define USER_SCRIPT_DONE "M117 User Script Done" + #define USER_SCRIPT_AUDIBLE_FEEDBACK + //#define USER_SCRIPT_RETURN // Return to status screen after a script + + #define USER_DESC_1 "Home & UBL Info" + #define USER_GCODE_1 "G28\nG29 W" + + #define USER_DESC_2 "Preheat for " PREHEAT_1_LABEL + #define USER_GCODE_2 "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND) + + #define USER_DESC_3 "Preheat for " PREHEAT_2_LABEL + #define USER_GCODE_3 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND) + + #define USER_DESC_4 "Heat Bed/Home/Level" + #define USER_GCODE_4 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29" + + #define USER_DESC_5 "Home & Info" + #define USER_GCODE_5 "G28\nM503" +#endif + +/** + * Host Action Commands + * + * Define host streamer action commands in compliance with the standard. + * + * See https://reprap.org/wiki/G-code#Action_commands + * Common commands ........ poweroff, pause, paused, resume, resumed, cancel + * G29_RETRY_AND_RECOVER .. probe_rewipe, probe_failed + * + * Some features add reason codes to extend these commands. + * + * Host Prompt Support enables Marlin to use the host for user prompts so + * filament runout and other processes can be managed from the host side. + */ +//#define HOST_ACTION_COMMANDS +#if ENABLED(HOST_ACTION_COMMANDS) + //#define HOST_PROMPT_SUPPORT +#endif + +//=========================================================================== +//====================== I2C Position Encoder Settings ====================== +//=========================================================================== + +/** + * I2C position encoders for closed loop control. + * Developed by Chris Barr at Aus3D. + * + * Wiki: http://wiki.aus3d.com.au/Magnetic_Encoder + * Github: https://github.com/Aus3D/MagneticEncoder + * + * Supplier: http://aus3d.com.au/magnetic-encoder-module + * Alternative Supplier: http://reliabuild3d.com/ + * + * Reliabuild encoders have been modified to improve reliability. + */ + +//#define I2C_POSITION_ENCODERS +#if ENABLED(I2C_POSITION_ENCODERS) + + #define I2CPE_ENCODER_CNT 1 // The number of encoders installed; max of 5 + // encoders supported currently. + + #define I2CPE_ENC_1_ADDR I2CPE_PRESET_ADDR_X // I2C address of the encoder. 30-200. + #define I2CPE_ENC_1_AXIS X_AXIS // Axis the encoder module is installed on. _AXIS. + #define I2CPE_ENC_1_TYPE I2CPE_ENC_TYPE_LINEAR // Type of encoder: I2CPE_ENC_TYPE_LINEAR -or- + // I2CPE_ENC_TYPE_ROTARY. + #define I2CPE_ENC_1_TICKS_UNIT 2048 // 1024 for magnetic strips with 2mm poles; 2048 for + // 1mm poles. For linear encoders this is ticks / mm, + // for rotary encoders this is ticks / revolution. + //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper + // steps per full revolution (motor steps/rev * microstepping) + //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the + // printer will attempt to correct the error; errors + // smaller than this are ignored to minimize effects of + // measurement noise / latency (filter). + + #define I2CPE_ENC_2_ADDR I2CPE_PRESET_ADDR_Y // Same as above, but for encoder 2. + #define I2CPE_ENC_2_AXIS Y_AXIS + #define I2CPE_ENC_2_TYPE I2CPE_ENC_TYPE_LINEAR + #define I2CPE_ENC_2_TICKS_UNIT 2048 + //#define I2CPE_ENC_2_TICKS_REV (16 * 200) + //#define I2CPE_ENC_2_INVERT + #define I2CPE_ENC_2_EC_METHOD I2CPE_ECM_MICROSTEP + #define I2CPE_ENC_2_EC_THRESH 0.10 + + #define I2CPE_ENC_3_ADDR I2CPE_PRESET_ADDR_Z // Encoder 3. Add additional configuration options + #define I2CPE_ENC_3_AXIS Z_AXIS // as above, or use defaults below. + + #define I2CPE_ENC_4_ADDR I2CPE_PRESET_ADDR_E // Encoder 4. + #define I2CPE_ENC_4_AXIS E_AXIS + + #define I2CPE_ENC_5_ADDR 34 // Encoder 5. + #define I2CPE_ENC_5_AXIS E_AXIS + + // Default settings for encoders which are enabled, but without settings configured above. + #define I2CPE_DEF_TYPE I2CPE_ENC_TYPE_LINEAR + #define I2CPE_DEF_ENC_TICKS_UNIT 2048 + #define I2CPE_DEF_TICKS_REV (16 * 200) + #define I2CPE_DEF_EC_METHOD I2CPE_ECM_NONE + #define I2CPE_DEF_EC_THRESH 0.1 + + //#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given + // axis after which the printer will abort. Comment out to + // disable abort behavior. + + #define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault + // for this amount of time (in ms) before the encoder + // is trusted again. + + /** + * Position is checked every time a new command is executed from the buffer but during long moves, + * this setting determines the minimum update time between checks. A value of 100 works well with + * error rolling average when attempting to correct only for skips and not for vibration. + */ + #define I2CPE_MIN_UPD_TIME_MS 4 // (ms) Minimum time between encoder checks. + + // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise. + #define I2CPE_ERR_ROLLING_AVERAGE + +#endif // I2C_POSITION_ENCODERS + +/** + * MAX7219 Debug Matrix + * + * Add support for a low-cost 8x8 LED Matrix based on the Max7219 chip as a realtime status display. + * Requires 3 signal wires. Some useful debug options are included to demonstrate its usage. + */ +//#define MAX7219_DEBUG +#if ENABLED(MAX7219_DEBUG) + #define MAX7219_CLK_PIN 64 + #define MAX7219_DIN_PIN 57 + #define MAX7219_LOAD_PIN 44 + + //#define MAX7219_GCODE // Add the M7219 G-code to control the LED matrix + #define MAX7219_INIT_TEST 2 // Do a test pattern at initialization (Set to 2 for spiral) + #define MAX7219_NUMBER_UNITS 1 // Number of Max7219 units in chain. + #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) + // connector at: right=0 bottom=-90 top=90 left=180 + //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side + + /** + * Sample debug features + * If you add more debug displays, be careful to avoid conflicts! + */ + #define MAX7219_DEBUG_PRINTER_ALIVE // Blink corner LED of 8x8 matrix to show that the firmware is functioning + #define MAX7219_DEBUG_PLANNER_HEAD 3 // Show the planner queue head position on this and the next LED matrix row + #define MAX7219_DEBUG_PLANNER_TAIL 5 // Show the planner queue tail position on this and the next LED matrix row + + #define MAX7219_DEBUG_PLANNER_QUEUE 0 // Show the current planner queue depth on this and the next LED matrix row + // If you experience stuttering, reboots, etc. this option can reveal how + // tweaks made to the configuration are affecting the printer in real-time. +#endif + +/** + * NanoDLP Sync support + * + * Add support for Synchronized Z moves when using with NanoDLP. G0/G1 axis moves will output "Z_move_comp" + * string to enable synchronization with DLP projector exposure. This change will allow to use + * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands + */ +//#define NANODLP_Z_SYNC +#if ENABLED(NANODLP_Z_SYNC) + //#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move. + // Default behavior is limited to Z axis only. +#endif + +/** + * WiFi Support (Espressif ESP32 WiFi) + */ +//#define WIFISUPPORT +#if ENABLED(WIFISUPPORT) + #define WIFI_SSID "Wifi SSID" + #define WIFI_PWD "Wifi Password" + //#define WEBSUPPORT // Start a webserver with auto-discovery + //#define OTASUPPORT // Support over-the-air firmware updates +#endif + +/** + * Prusa Multi-Material Unit v2 + * Enable in Configuration.h + */ +#if ENABLED(PRUSA_MMU2) + + // Serial port used for communication with MMU2. + // For AVR enable the UART port used for the MMU. (e.g., internalSerial) + // For 32-bit boards check your HAL for available serial ports. (e.g., Serial2) + #define INTERNAL_SERIAL_PORT 2 + #define MMU2_SERIAL internalSerial + + // Use hardware reset for MMU if a pin is defined for it + //#define MMU2_RST_PIN 23 + + // Enable if the MMU2 has 12V stepper motors (MMU2 Firmware 1.0.2 and up) + //#define MMU2_MODE_12V + + // G-code to execute when MMU2 F.I.N.D.A. probe detects filament runout + #define MMU2_FILAMENT_RUNOUT_SCRIPT "M600" + + // Add an LCD menu for MMU2 + //#define MMU2_MENUS + #if ENABLED(MMU2_MENUS) + // Settings for filament load / unload from the LCD menu. + // This is for Prusa MK3-style extruders. Customize for your hardware. + #define MMU2_FILAMENTCHANGE_EJECT_FEED 80.0 + #define MMU2_LOAD_TO_NOZZLE_SEQUENCE \ + { 7.2, 562 }, \ + { 14.4, 871 }, \ + { 36.0, 1393 }, \ + { 14.4, 871 }, \ + { 50.0, 198 } + + #define MMU2_RAMMING_SEQUENCE \ + { 1.0, 1000 }, \ + { 1.0, 1500 }, \ + { 2.0, 2000 }, \ + { 1.5, 3000 }, \ + { 2.5, 4000 }, \ + { -15.0, 5000 }, \ + { -14.0, 1200 }, \ + { -6.0, 600 }, \ + { 10.0, 700 }, \ + { -10.0, 400 }, \ + { -50.0, 2000 } + + #endif + + //#define MMU2_DEBUG // Write debug info to serial output + +#endif // PRUSA_MMU2 + +/** + * Advanced Print Counter settings + */ +#if ENABLED(PRINTCOUNTER) + #define SERVICE_WARNING_BUZZES 3 + // Activate up to 3 service interval watchdogs + //#define SERVICE_NAME_1 "Service S" + //#define SERVICE_INTERVAL_1 100 // print hours + //#define SERVICE_NAME_2 "Service L" + //#define SERVICE_INTERVAL_2 200 // print hours + //#define SERVICE_NAME_3 "Service 3" + //#define SERVICE_INTERVAL_3 1 // print hours +#endif + +// @section develop + +/** + * M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins + */ +//#define PINS_DEBUGGING + +// Enable Marlin dev mode which adds some special commands +//#define MARLIN_DEV_MODE diff --git a/config/examples/Tevo/Tornado/_Bootscreen.h b/config/examples/Tevo/Tornado/_Bootscreen.h new file mode 100644 index 0000000000..ebec255674 --- /dev/null +++ b/config/examples/Tevo/Tornado/_Bootscreen.h @@ -0,0 +1,85 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Made with Marlin Bitmap Converter + * http://marlinfw.org/tools/u8glib/converter.html + */ +#define CUSTOM_BOOTSCREEN_TIMEOUT 1500 +#define CUSTOM_BOOTSCREEN_BMPWIDTH 112 + +const unsigned char custom_start_bmp[] PROGMEM = { + B00000000,B00000000,B00011111,B11111111,B11110000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00011111,B11111111,B11111111,B11111111,B11110000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00000001,B11111111,B11111111,B11111111,B11111111,B11111111,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00001111,B11111110,B00000000,B00001111,B11111111,B11111111,B11100000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00111111,B00000000,B00000000,B00000000,B00000011,B11111111,B11111100,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B01111000,B00000000,B00000000,B00000000,B00000000,B00001111,B11111110,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B11100000,B01111111,B11000000,B00000000,B00000000,B00000000,B11111111,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B11001111,B11110000,B00000000,B00000000,B00000000,B00000000,B00011111,B10000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B11111110,B00000000,B00000000,B00000000,B00000000,B00000000,B00000111,B10000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B11111100,B00000000,B00000000,B00000000,B00000000,B00000000,B00000011,B10000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B01111100,B00000000,B00000000,B00000000,B00000000,B00011110,B00000111,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00011110,B00000000,B00000000,B00000000,B00000000,B00000111,B11001111,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00000111,B10000000,B00000000,B00000000,B00000000,B00000111,B11111111,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00010000,B11111100,B00000000,B00000000,B00000000,B00011111,B11111110,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00010000,B00011111,B11111000,B00000000,B00000011,B11111110,B00111110,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00011000,B00000000,B01111111,B11111111,B11111111,B11000000,B11111100,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00011100,B00000000,B00000000,B00000000,B00000000,B00000011,B11111000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00001110,B00000000,B00000000,B00000000,B00000000,B00011111,B11110000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00000011,B10000000,B00000000,B00000000,B00000010,B11111111,B11000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00000001,B11100000,B00000000,B00000000,B00001111,B11111111,B10000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00111000,B00000000,B00000000,B11111111,B11100111,B10000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000100,B00000000,B00000011,B11100000,B00000111,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000111,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00001111,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00011110,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00000000,B01100000,B00000000,B00000000,B00000000,B01111100,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00110000,B00000000,B00000000,B00000001,B11110000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00011100,B00000000,B00000000,B00001111,B11000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000111,B10000000,B00000000,B11111110,B11000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B01000000,B00000001,B00000000,B11100000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B00000000,B00000000,B00000001,B11100000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B00000000,B00000000,B00000111,B11000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B00000000,B00000000,B00001111,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B00000000,B00000000,B01111110,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B00000000,B00000011,B11110110,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B00000000,B00000000,B00000110,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B10000000,B00000000,B00001110,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B01000000,B00000000, + B00000000,B00000000,B01110000,B00000000,B00111100,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00011111,B11100000,B00000000, + B00000000,B00000000,B00111000,B00000000,B11111000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00011111,B11000000,B00000000, + B00000000,B00000000,B00001100,B00000111,B11110000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00001111,B10000000,B00000000, + B00000000,B00000000,B00000000,B00001100,B00110000,B00000000,B00000000,B10000000,B00000000,B00110000,B00000000,B11111000,B00000111,B11000000,B00000000, + B00000000,B00000000,B00000000,B00000000,B01110000,B00011111,B11011111,B11111110,B11111110,B01111000,B00110011,B11111000,B01100111,B11000011,B11111000, + B00000000,B00000000,B00000000,B00000000,B11100000,B01111111,B11111111,B11111111,B01111110,B11111000,B11111111,B11110001,B11111111,B11000111,B11111100, + B00000000,B00000000,B00000000,B00000011,B11000001,B11111111,B11111111,B11011111,B10111111,B11111101,B11111111,B11110011,B11111111,B11001111,B11111110, + B00000000,B00000000,B00000000,B00000111,B01100001,B11111111,B11100111,B10111111,B10111111,B11111101,B11111111,B11110111,B11111111,B11011111,B11111110, + B00000000,B00000000,B00000000,B00000000,B01100001,B11100000,B01100111,B10111111,B10111111,B11111111,B11111111,B11110111,B11111111,B11111110,B00001110, + B00000000,B00000000,B00000000,B00000001,B11000001,B11000000,B01100111,B10111111,B00111111,B01111011,B10000001,B11100111,B00000111,B10111000,B00001110, + B00000000,B00000000,B00000000,B00011111,B10000001,B10000001,B11100111,B11000000,B00111110,B01111011,B11101111,B11100111,B11111111,B10111000,B00011100, + B00000000,B00000000,B00000000,B00001111,B00000001,B11111111,B11100111,B11100000,B00011110,B01111011,B11111111,B11111111,B11111111,B11111111,B11111100, + B00000000,B00000000,B00000000,B00111111,B10000000,B11111111,B11001111,B11111000,B01111110,B01111011,B11111111,B11111111,B11111111,B11111111,B11111100, + B00000000,B00000000,B00000000,B00111111,B00000000,B01111111,B10011111,B11111000,B01111110,B01111001,B11111111,B11111011,B11110111,B11101111,B11111000, + B00000000,B00000000,B00000000,B00011111,B00000000,B00111111,B00011110,B00000000,B00000010,B01111111,B11110001,B00000000,B00000100,B00000011,B11110000, + B00000000,B00000000,B00000000,B00001100,B00000000,B00000000,B00000000,B00000000,B00000000,B00001110,B00000000,B00000000,B00000000,B00000000,B00000000 +}; diff --git a/config/examples/TheBorg/Configuration.h b/config/examples/TheBorg/Configuration.h index f0adb0908b..c2d9c71fe2 100644 --- a/config/examples/TheBorg/Configuration.h +++ b/config/examples/TheBorg/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_THE_BORG #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu //#define CUSTOM_MACHINE_NAME "3D Printer" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1523,8 +1529,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1681,6 +1690,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1908,31 +1925,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1966,15 +1964,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1987,6 +1976,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2012,17 +2043,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2118,8 +2156,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/TheBorg/Configuration_adv.h b/config/examples/TheBorg/Configuration_adv.h index a77c234ee6..af5b4e00a6 100644 --- a/config/examples/TheBorg/Configuration_adv.h +++ b/config/examples/TheBorg/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/TinyBoy2/Configuration.h b/config/examples/TinyBoy2/Configuration.h index e810771811..5d62466586 100644 --- a/config/examples/TinyBoy2/Configuration.h +++ b/config/examples/TinyBoy2/Configuration.h @@ -145,14 +145,12 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_MELZI #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #if ENABLED(TB2_L10) #define CUSTOM_MACHINE_NAME "TinyBoy2 L10" #elif ENABLED(TB2_L16) @@ -161,8 +159,8 @@ #error "Please select TB2_L10 or TB2_L16" #endif -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -299,7 +297,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -381,6 +386,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -417,7 +423,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -551,7 +557,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1579,8 +1585,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1737,6 +1746,14 @@ // #define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1964,31 +1981,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -2022,15 +2020,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -2043,6 +2032,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2068,17 +2099,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2174,8 +2212,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/TinyBoy2/Configuration_adv.h b/config/examples/TinyBoy2/Configuration_adv.h index 739f7ce78a..d3ec36b759 100644 --- a/config/examples/TinyBoy2/Configuration_adv.h +++ b/config/examples/TinyBoy2/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu #define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Tronxy/X1/Configuration.h b/config/examples/Tronxy/X1/Configuration.h index 6979cde44a..68884c94a6 100644 --- a/config/examples/Tronxy/X1/Configuration.h +++ b/config/examples/Tronxy/X1/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_MELZI #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Tronxy X1" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 11 #define TEMP_SENSOR_1 0 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1523,8 +1529,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1681,6 +1690,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1908,31 +1925,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1966,15 +1964,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1987,6 +1976,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2012,17 +2043,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2118,8 +2156,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Tronxy/X3A/Configuration.h b/config/examples/Tronxy/X3A/Configuration.h index 6b39b8d13f..0d7192bb01 100644 --- a/config/examples/Tronxy/X3A/Configuration.h +++ b/config/examples/Tronxy/X3A/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_MELZI //63 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Tronxy X3A" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 6 #define TEMP_SENSOR_1 0 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1527,8 +1533,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1685,6 +1694,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1912,31 +1929,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1970,15 +1968,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1991,6 +1980,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2016,17 +2047,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2122,8 +2160,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Tronxy/X3A/Configuration_adv.h b/config/examples/Tronxy/X3A/Configuration_adv.h index cb44fb88a0..3da702d43d 100644 --- a/config/examples/Tronxy/X3A/Configuration_adv.h +++ b/config/examples/Tronxy/X3A/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Tronxy/X5S-2E/Configuration.h b/config/examples/Tronxy/X5S-2E/Configuration.h index caa7d9dee8..cc6084f299 100644 --- a/config/examples/Tronxy/X5S-2E/Configuration.h +++ b/config/examples/Tronxy/X5S-2E/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_TRONXY_V3_1_0 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Tronxy X5S-2E" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -279,7 +277,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -361,6 +366,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -397,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -527,7 +533,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. // //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1544,8 +1550,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1702,6 +1711,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1929,31 +1946,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1987,15 +1985,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -2008,6 +1997,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2033,17 +2064,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2139,8 +2177,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Tronxy/X5S-2E/Configuration_adv.h b/config/examples/Tronxy/X5S-2E/Configuration_adv.h index 5a4c32f8cd..a445491432 100644 --- a/config/examples/Tronxy/X5S-2E/Configuration_adv.h +++ b/config/examples/Tronxy/X5S-2E/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu #define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Tronxy/X5S/Configuration.h b/config/examples/Tronxy/X5S/Configuration.h index 0f57f82223..c24a9c4ec5 100644 --- a/config/examples/Tronxy/X5S/Configuration.h +++ b/config/examples/Tronxy/X5S/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_MELZI_TRONXY #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Tronxy X5S" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1523,8 +1529,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1681,6 +1690,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1908,31 +1925,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1966,15 +1964,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1987,6 +1976,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2012,17 +2043,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2118,8 +2156,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Tronxy/XY100/Configuration.h b/config/examples/Tronxy/XY100/Configuration.h index bca3d4195d..e3fb4ff147 100644 --- a/config/examples/Tronxy/XY100/Configuration.h +++ b/config/examples/Tronxy/XY100/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_MELZI #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "TronXY XY100" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -525,7 +531,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1534,8 +1540,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1692,6 +1701,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1919,31 +1936,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1977,15 +1975,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1998,6 +1987,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2023,17 +2054,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2129,8 +2167,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/UltiMachine/Archim1/Configuration.h b/config/examples/UltiMachine/Archim1/Configuration.h index 16e6662b26..a76625f431 100644 --- a/config/examples/UltiMachine/Archim1/Configuration.h +++ b/config/examples/UltiMachine/Archim1/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_ARCHIM1 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu //#define CUSTOM_MACHINE_NAME "3D Printer" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1523,8 +1529,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1681,6 +1690,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1908,31 +1925,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1966,15 +1964,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1987,6 +1976,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2012,17 +2043,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2118,8 +2156,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/UltiMachine/Archim1/Configuration_adv.h b/config/examples/UltiMachine/Archim1/Configuration_adv.h index d711c6b6de..0f5c6d0893 100644 --- a/config/examples/UltiMachine/Archim1/Configuration_adv.h +++ b/config/examples/UltiMachine/Archim1/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/UltiMachine/Archim2/Configuration.h b/config/examples/UltiMachine/Archim2/Configuration.h index b0b32750e1..ce3ae66783 100644 --- a/config/examples/UltiMachine/Archim2/Configuration.h +++ b/config/examples/UltiMachine/Archim2/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_ARCHIM2 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu //#define CUSTOM_MACHINE_NAME "3D Printer" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1523,8 +1529,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1681,6 +1690,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1908,31 +1925,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1966,15 +1964,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1987,6 +1976,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2012,17 +2043,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2118,8 +2156,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/UltiMachine/Archim2/Configuration_adv.h b/config/examples/UltiMachine/Archim2/Configuration_adv.h index e0c128b336..c5b29720ce 100644 --- a/config/examples/UltiMachine/Archim2/Configuration_adv.h +++ b/config/examples/UltiMachine/Archim2/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/VORONDesign/Configuration.h b/config/examples/VORONDesign/Configuration.h index 8585a80109..5f4870c385 100644 --- a/config/examples/VORONDesign/Configuration.h +++ b/config/examples/VORONDesign/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_VORON #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "VORON 2.0" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 5 @@ -519,7 +525,7 @@ #define MAX_BED_POWER 205 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1532,8 +1538,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1690,6 +1699,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1917,31 +1934,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1975,15 +1973,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1996,6 +1985,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2021,17 +2052,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2127,8 +2165,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/VORONDesign/Configuration_adv.h b/config/examples/VORONDesign/Configuration_adv.h index cfda48dc98..601864afdc 100644 --- a/config/examples/VORONDesign/Configuration_adv.h +++ b/config/examples/VORONDesign/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Velleman/K8200/Configuration.h b/config/examples/Velleman/K8200/Configuration.h index 4efe30bc46..3ea687c854 100644 --- a/config/examples/Velleman/K8200/Configuration.h +++ b/config/examples/Velleman/K8200/Configuration.h @@ -145,18 +145,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_K8200 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "K8200" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 #if ENABLED(K8200_VM8201) #define MACHINE_UUID "2b7dea3b-844e-4ab1-aa96-bb6406607d6e" // K8200 standard config with VM8201 (Display) #else @@ -297,7 +295,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -379,6 +384,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -415,7 +421,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -538,7 +544,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1553,8 +1559,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1714,6 +1723,14 @@ // #define REVERSE_MENU_DIRECTION // K8200: for Display VM8201 encoder on right side +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1941,31 +1958,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1999,15 +1997,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -2022,6 +2011,11 @@ #endif // K8200_VM8201 +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2047,17 +2041,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2153,8 +2154,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Velleman/K8200/Configuration_adv.h b/config/examples/Velleman/K8200/Configuration_adv.h index 7463788566..0eb7e6b606 100644 --- a/config/examples/Velleman/K8200/Configuration_adv.h +++ b/config/examples/Velleman/K8200/Configuration_adv.h @@ -663,6 +663,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -864,6 +865,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1050,7 +1054,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1148,6 +1152,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1377,6 +1382,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1762,6 +1770,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2447,6 +2458,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Velleman/K8400/Configuration.h b/config/examples/Velleman/K8400/Configuration.h index 1e6550e5d7..543fbf93b9 100644 --- a/config/examples/Velleman/K8400/Configuration.h +++ b/config/examples/Velleman/K8400/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_K8400 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu //#define CUSTOM_MACHINE_NAME "3D Printer" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1523,8 +1529,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1681,6 +1690,14 @@ // #define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1908,31 +1925,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1966,15 +1964,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1987,6 +1976,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2012,17 +2043,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2119,8 +2157,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Velleman/K8400/Configuration_adv.h b/config/examples/Velleman/K8400/Configuration_adv.h index b50662fc5b..5b383c2bfe 100644 --- a/config/examples/Velleman/K8400/Configuration_adv.h +++ b/config/examples/Velleman/K8400/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Velleman/K8400/Dual-head/Configuration.h b/config/examples/Velleman/K8400/Dual-head/Configuration.h index 7e41e8ba87..eb0365fc1a 100644 --- a/config/examples/Velleman/K8400/Dual-head/Configuration.h +++ b/config/examples/Velleman/K8400/Dual-head/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_K8400 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu //#define CUSTOM_MACHINE_NAME "3D Printer" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 5 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1523,8 +1529,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1681,6 +1690,14 @@ // #define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1908,31 +1925,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1966,15 +1964,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1987,6 +1976,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2012,17 +2043,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2119,8 +2157,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/WASP/PowerWASP/Configuration.h b/config/examples/WASP/PowerWASP/Configuration.h index 937e1ef51a..55dcae711c 100644 --- a/config/examples/WASP/PowerWASP/Configuration.h +++ b/config/examples/WASP/PowerWASP/Configuration.h @@ -148,18 +148,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_ULTIMAKER #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message -#define CUSTOM_MACHINE_NAME " PowerWASP is " +// Name displayed in the LCD "Ready" message and Info menu +#define CUSTOM_MACHINE_NAME "PowerWASP" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -296,7 +294,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -378,6 +383,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -414,7 +420,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 -1 #define TEMP_SENSOR_1 0 @@ -533,7 +539,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1542,8 +1548,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1700,6 +1709,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1927,31 +1944,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1985,15 +1983,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -2006,6 +1995,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2031,17 +2062,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2137,8 +2175,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/WASP/PowerWASP/Configuration_adv.h b/config/examples/WASP/PowerWASP/Configuration_adv.h index 178f02d96f..ec5ba58a4c 100644 --- a/config/examples/WASP/PowerWASP/Configuration_adv.h +++ b/config/examples/WASP/PowerWASP/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Wanhao/Duplicator 6/Configuration.h b/config/examples/Wanhao/Duplicator 6/Configuration.h index ca6554229d..fa2d1cb3d0 100644 --- a/config/examples/Wanhao/Duplicator 6/Configuration.h +++ b/config/examples/Wanhao/Duplicator 6/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_ULTIMAIN_2 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Duplicator 6" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 20 #define TEMP_SENSOR_1 0 @@ -519,7 +525,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1533,8 +1539,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1691,6 +1700,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1918,34 +1935,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -#define U8GLIB_SSD1306 -#define LCD_WIDTH 22 -#define LCD_HEIGHT 5 -#define LCD_RESET_PIN 5 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1979,15 +1974,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -2000,6 +1986,51 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +#define U8GLIB_SSD1306 +#define LCD_WIDTH 22 +#define LCD_HEIGHT 5 +#define LCD_RESET_PIN 5 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2025,17 +2056,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2131,8 +2169,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h index 868ebec1f9..1276862c07 100644 --- a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 70*60, 70*60, 15*60, 6*60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -853,6 +854,9 @@ // Include a page of printer information in the LCD Main Menu #define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1039,7 +1043,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1137,6 +1141,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1366,6 +1371,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1751,6 +1759,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2436,6 +2447,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h b/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h new file mode 100644 index 0000000000..6672d21486 --- /dev/null +++ b/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h @@ -0,0 +1,2210 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Configuration.h + * + * Basic settings such as: + * + * - Type of electronics + * - Type of temperature sensor + * - Printer geometry + * - Endstop configuration + * - LCD controller + * - Extra features + * + * Advanced settings can be found in Configuration_adv.h + * + */ +#define CONFIGURATION_H_VERSION 020000 + +//=========================================================================== +//============================= Getting Started ============================= +//=========================================================================== + +/** + * Here are some standard links for getting your machine calibrated: + * + * http://reprap.org/wiki/Calibration + * http://youtu.be/wAL9d7FgInk + * http://calculator.josefprusa.cz + * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide + * http://www.thingiverse.com/thing:5573 + * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap + * http://www.thingiverse.com/thing:298812 + */ + +//=========================================================================== +//============================= DELTA Printer =============================== +//=========================================================================== +// For a Delta printer start with one of the configuration files in the +// config/examples/delta directory and customize for your machine. +// + +//=========================================================================== +//============================= SCARA Printer =============================== +//=========================================================================== +// For a SCARA printer start with the configuration files in +// config/examples/SCARA and customize for your machine. +// + +// @section info + +// User-specified version info of this build to display in [Pronterface, etc] terminal window during +// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this +// build by the user have been successfully uploaded into firmware. +#define STRING_CONFIG_H_AUTHOR "(thisiskeithb, Wanhao i3 Mini)" // Who made the changes. +#define SHOW_BOOTSCREEN +#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1 +//#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2 + +/** + * *** VENDORS PLEASE READ *** + * + * Marlin allows you to add a custom boot image for Graphical LCDs. + * With this option Marlin will first show your custom screen followed + * by the standard Marlin logo with version number and web URL. + * + * We encourage you to take advantage of this new feature and we also + * respectfully request that you retain the unmodified Marlin boot screen. + */ + +// Enable to show the bitmap in Marlin/_Bootscreen.h on startup. +//#define SHOW_CUSTOM_BOOTSCREEN + +// Enable to show the bitmap in Marlin/_Statusscreen.h on the status screen. +//#define CUSTOM_STATUS_SCREEN_IMAGE + +// @section machine + +/** + * Select the serial port on the board to use for communication with the host. + * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. + * + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] + */ +#define SERIAL_PORT 0 + +/** + * Select a secondary serial port on the board to use for communication with the host. + * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. + * + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] + */ +//#define SERIAL_PORT_2 -1 + +/** + * This setting determines the communication speed of the printer. + * + * 250000 works in most cases, but you might try a lower speed if + * you commonly experience drop-outs during host printing. + * You may try up to 1000000 to speed up SD file transfer. + * + * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000] + */ +#define BAUDRATE 250000 + +// Enable the Bluetooth serial interface on AT90USB devices +//#define BLUETOOTH + +// Choose the name from boards.h that matches your setup +#ifndef MOTHERBOARD + #define MOTHERBOARD BOARD_WANHAO_ONEPLUS +#endif + +// Name displayed in the LCD "Ready" message and Info menu +#define CUSTOM_MACHINE_NAME "i3 Mini" + +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 +//#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" + +// @section extruder + +// This defines the number of extruders +// :[1, 2, 3, 4, 5, 6] +#define EXTRUDERS 1 + +// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc. +#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 + +// For Cyclops or any "multi-extruder" that shares a single nozzle. +//#define SINGLENOZZLE + +/** + * Průša MK2 Single Nozzle Multi-Material Multiplexer, and variants. + * + * This device allows one stepper driver on a control board to drive + * two to eight stepper motors, one at a time, in a manner suitable + * for extruders. + * + * This option only allows the multiplexer to switch on tool-change. + * Additional options to configure custom E moves are pending. + */ +//#define MK2_MULTIPLEXER +#if ENABLED(MK2_MULTIPLEXER) + // Override the default DIO selector pins here, if needed. + // Some pins files may provide defaults for these pins. + //#define E_MUX0_PIN 40 // Always Required + //#define E_MUX1_PIN 42 // Needed for 3 to 8 inputs + //#define E_MUX2_PIN 44 // Needed for 5 to 8 inputs +#endif + +/** + * Prusa Multi-Material Unit v2 + * + * Requires NOZZLE_PARK_FEATURE to park print head in case MMU unit fails. + * Requires EXTRUDERS = 5 + * + * For additional configuration see Configuration_adv.h + */ +//#define PRUSA_MMU2 + +// A dual extruder that uses a single stepper motor +//#define SWITCHING_EXTRUDER +#if ENABLED(SWITCHING_EXTRUDER) + #define SWITCHING_EXTRUDER_SERVO_NR 0 + #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3] + #if EXTRUDERS > 3 + #define SWITCHING_EXTRUDER_E23_SERVO_NR 1 + #endif +#endif + +// A dual-nozzle that uses a servomotor to raise/lower one (or both) of the nozzles +//#define SWITCHING_NOZZLE +#if ENABLED(SWITCHING_NOZZLE) + #define SWITCHING_NOZZLE_SERVO_NR 0 + //#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second + #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo) +#endif + +/** + * Two separate X-carriages with extruders that connect to a moving part + * via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN. + */ +//#define PARKING_EXTRUDER + +/** + * Two separate X-carriages with extruders that connect to a moving part + * via a magnetic docking mechanism using movements and no solenoid + * + * project : https://www.thingiverse.com/thing:3080893 + * movements : https://youtu.be/0xCEiG9VS3k + * https://youtu.be/Bqbcs0CU2FE + */ +//#define MAGNETIC_PARKING_EXTRUDER + +#if EITHER(PARKING_EXTRUDER, MAGNETIC_PARKING_EXTRUDER) + + #define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders + #define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder + //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381 + + #if ENABLED(PARKING_EXTRUDER) + + #define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage + #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil + #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined. + //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381 + + #elif ENABLED(MAGNETIC_PARKING_EXTRUDER) + + #define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point + #define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple + #define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point + #define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling + + #endif + +#endif + +/** + * Switching Toolhead + * + * Support for swappable and dockable toolheads, such as + * the E3D Tool Changer. Toolheads are locked with a servo. + */ +//#define SWITCHING_TOOLHEAD + +/** + * Magnetic Switching Toolhead + * + * Support swappable and dockable toolheads with a magnetic + * docking mechanism using movement and no servo. + */ +//#define MAGNETIC_SWITCHING_TOOLHEAD + +/** + * Electromagnetic Switching Toolhead + * + * Parking for CoreXY / HBot kinematics. + * Toolheads are parked at one edge and held with an electromagnet. + * Supports more than 2 Toolheads. See https://youtu.be/JolbsAKTKf4 + */ +//#define ELECTROMAGNETIC_SWITCHING_TOOLHEAD + +#if ANY(SWITCHING_TOOLHEAD, MAGNETIC_SWITCHING_TOOLHEAD, ELECTROMAGNETIC_SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_Y_POS 235 // (mm) Y position of the toolhead dock + #define SWITCHING_TOOLHEAD_Y_SECURITY 10 // (mm) Security distance Y axis + #define SWITCHING_TOOLHEAD_Y_CLEAR 60 // (mm) Minimum distance from dock for unobstructed X axis + #define SWITCHING_TOOLHEAD_X_POS { 215, 0 } // (mm) X positions for parking the extruders + #if ENABLED(SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_SERVO_NR 2 // Index of the servo connector + #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock + #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif + #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching + #endif +#endif + +/** + * "Mixing Extruder" + * - Adds G-codes M163 and M164 to set and "commit" the current mix factors. + * - Extends the stepping routines to move multiple steppers in proportion to the mix. + * - Optional support for Repetier Firmware's 'M164 S' supporting virtual tools. + * - This implementation supports up to two mixing extruders. + * - Enable DIRECT_MIXING_IN_G1 for M165 and mixing in G1 (from Pia Taubert's reference implementation). + */ +//#define MIXING_EXTRUDER +#if ENABLED(MIXING_EXTRUDER) + #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder + #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164 + //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands + //#define GRADIENT_MIX // Support for gradient mixing with M166 and LCD + #if ENABLED(GRADIENT_MIX) + //#define GRADIENT_VTOOL // Add M166 T to use a V-tool index as a Gradient alias + #endif +#endif + +// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). +// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). +// For the other hotends it is their distance from the extruder 0 hotend. +//#define HOTEND_OFFSET_X { 0.0, 20.00 } // (mm) relative X-offset for each nozzle +//#define HOTEND_OFFSET_Y { 0.0, 5.00 } // (mm) relative Y-offset for each nozzle +//#define HOTEND_OFFSET_Z { 0.0, 0.00 } // (mm) relative Z-offset for each nozzle + +// @section machine + +/** + * Power Supply Control + * + * Enable and connect the power supply to the PS_ON_PIN. + * Specify whether the power supply is active HIGH or active LOW. + */ +//#define PSU_CONTROL +//#define PSU_NAME "Power Supply" + +#if ENABLED(PSU_CONTROL) + #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2) + + //#define PS_DEFAULT_OFF // Keep power off until enabled directly with M80 + + //#define AUTO_POWER_CONTROL // Enable automatic control of the PS_ON pin + #if ENABLED(AUTO_POWER_CONTROL) + #define AUTO_POWER_FANS // Turn on PSU if fans need power + #define AUTO_POWER_E_FANS + #define AUTO_POWER_CONTROLLERFAN + #define AUTO_POWER_CHAMBER_FAN + //#define AUTO_POWER_E_TEMP 50 // (°C) Turn on PSU over this temperature + //#define AUTO_POWER_CHAMBER_TEMP 30 // (°C) Turn on PSU over this temperature + #define POWER_TIMEOUT 30 + #endif +#endif + +// @section temperature + +//=========================================================================== +//============================= Thermal Settings ============================ +//=========================================================================== + +/** + * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table + * + * Temperature sensors available: + * + * -4 : thermocouple with AD8495 + * -3 : thermocouple with MAX31855 (only for sensor 0) + * -2 : thermocouple with MAX6675 (only for sensor 0) + * -1 : thermocouple with AD595 + * 0 : not used + * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 3 : Mendel-parts thermistor (4.7k pullup) + * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! + * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) + * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) + * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) + * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) + * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) + * 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) + * 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) + * 10 : 100k RS thermistor 198-961 (4.7k pullup) + * 11 : 100k beta 3950 1% thermistor (4.7k pullup) + * 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) + * 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" + * 15 : 100k thermistor calibration for JGAurora A5 hotend + * 18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327 + * 20 : the PT100 circuit found in the Ultimainboard V2.x + * 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 + * 61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup + * 66 : 4.7M High Temperature thermistor from Dyze Design + * 67 : 450C thermistor from SliceEngineering + * 70 : the 100K thermistor found in the bq Hephestos 2 + * 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor + * + * 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k. + * (but gives greater accuracy and more stable PID) + * 51 : 100k thermistor - EPCOS (1k pullup) + * 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup) + * 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) + * + * 1047 : Pt1000 with 4k7 pullup + * 1010 : Pt1000 with 1k pullup (non standard) + * 147 : Pt100 with 4k7 pullup + * 110 : Pt100 with 1k pullup (non standard) + * + * 1000 : Custom - Specify parameters in Configuration_adv.h + * + * Use these for Testing or Development purposes. NEVER for production machine. + * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. + * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. + * + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + */ +#define TEMP_SENSOR_0 13 +#define TEMP_SENSOR_1 0 +#define TEMP_SENSOR_2 0 +#define TEMP_SENSOR_3 0 +#define TEMP_SENSOR_4 0 +#define TEMP_SENSOR_5 0 +#define TEMP_SENSOR_BED 0 +#define TEMP_SENSOR_CHAMBER 0 + +// Dummy thermistor constant temperature readings, for use with 998 and 999 +#define DUMMY_THERMISTOR_998_VALUE 25 +#define DUMMY_THERMISTOR_999_VALUE 100 + +// Use temp sensor 1 as a redundant sensor with sensor 0. If the readings +// from the two sensors differ too much the print will be aborted. +//#define TEMP_SENSOR_1_AS_REDUNDANT +#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 + +#define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109 +#define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer +#define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target + +#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190 +#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer +#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target + +// Below this temperature the heater will be switched off +// because it probably indicates a broken thermistor wire. +#define HEATER_0_MINTEMP 5 +#define HEATER_1_MINTEMP 5 +#define HEATER_2_MINTEMP 5 +#define HEATER_3_MINTEMP 5 +#define HEATER_4_MINTEMP 5 +#define HEATER_5_MINTEMP 5 +#define BED_MINTEMP 5 + +// Above this temperature the heater will be switched off. +// This can protect components from overheating, but NOT from shorts and failures. +// (Use MINTEMP for thermistor short/failure protection.) +#define HEATER_0_MAXTEMP 275 +#define HEATER_1_MAXTEMP 275 +#define HEATER_2_MAXTEMP 275 +#define HEATER_3_MAXTEMP 275 +#define HEATER_4_MAXTEMP 275 +#define HEATER_5_MAXTEMP 275 +#define BED_MAXTEMP 150 + +//=========================================================================== +//============================= PID Settings ================================ +//=========================================================================== +// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning + +// Comment the following line to disable PID and enable bang-bang. +#define PIDTEMP +#define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current +#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current +#define PID_K1 0.95 // Smoothing factor within any PID loop +#if ENABLED(PIDTEMP) + #define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM) + #define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM) + //#define PID_DEBUG // Sends debug data to the serial port. + //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX + //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay + //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] + #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature + // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. + + // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it + + // Wanhao Duplicator i3 Mini & rebrands + #define DEFAULT_Kp 22.2 + #define DEFAULT_Ki 1.08 + #define DEFAULT_Kd 114 + + // MakerGear + //#define DEFAULT_Kp 7.0 + //#define DEFAULT_Ki 0.1 + //#define DEFAULT_Kd 12 + + // Mendel Parts V9 on 12V + //#define DEFAULT_Kp 63.0 + //#define DEFAULT_Ki 2.25 + //#define DEFAULT_Kd 440 + +#endif // PIDTEMP + +//=========================================================================== +//====================== PID > Bed Temperature Control ====================== +//=========================================================================== + +/** + * PID Bed Heating + * + * If this option is enabled set PID constants below. + * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis. + * + * The PID frequency will be the same as the extruder PWM. + * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz, + * which is fine for driving a square wave into a resistive load and does not significantly + * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W + * heater. If your configuration is significantly different than this and you don't understand + * the issues involved, don't use bed PID until someone else verifies that your hardware works. + */ +//#define PIDTEMPBED + +//#define BED_LIMIT_SWITCHING + +/** + * Max Bed Power + * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis). + * When set to any value below 255, enables a form of PWM to the bed that acts like a divider + * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED) + */ +#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current + +#if ENABLED(PIDTEMPBED) + //#define MIN_BED_POWER 0 + //#define PID_BED_DEBUG // Sends debug data to the serial port. + + //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) + //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 + + //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) + //from pidautotune + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 + + // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. +#endif // PIDTEMPBED + +// @section extruder + +/** + * Prevent extrusion if the temperature is below EXTRUDE_MINTEMP. + * Add M302 to set the minimum extrusion temperature and/or turn + * cold extrusion prevention on and off. + * + * *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! *** + */ +#define PREVENT_COLD_EXTRUSION +#define EXTRUDE_MINTEMP 170 + +/** + * Prevent a single extrusion longer than EXTRUDE_MAXLENGTH. + * Note: For Bowden Extruders make this large enough to allow load/unload. + */ +#define PREVENT_LENGTHY_EXTRUDE +#define EXTRUDE_MAXLENGTH 200 + +//=========================================================================== +//======================== Thermal Runaway Protection ======================= +//=========================================================================== + +/** + * Thermal Protection provides additional protection to your printer from damage + * and fire. Marlin always includes safe min and max temperature ranges which + * protect against a broken or disconnected thermistor wire. + * + * The issue: If a thermistor falls out, it will report the much lower + * temperature of the air in the room, and the the firmware will keep + * the heater on. + * + * If you get "Thermal Runaway" or "Heating failed" errors the + * details can be tuned in Configuration_adv.h + */ + +#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders +#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed +#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber + +//=========================================================================== +//============================= Mechanical Settings ========================= +//=========================================================================== + +// @section machine + +// Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics +// either in the usual order or reversed +//#define COREXY +//#define COREXZ +//#define COREYZ +//#define COREYX +//#define COREZX +//#define COREZY + +//=========================================================================== +//============================== Endstop Settings =========================== +//=========================================================================== + +// @section homing + +// Specify here all the endstop connectors that are connected to any endstop or probe. +// Almost all printers will be using one per axis. Probes will use one or more of the +// extra connectors. Leave undefined any used for non-endstop and non-probe purposes. +//#define USE_XMIN_PLUG +#define USE_YMIN_PLUG +#define USE_ZMIN_PLUG +#define USE_XMAX_PLUG +//#define USE_YMAX_PLUG +//#define USE_ZMAX_PLUG + +// Enable pullup for all endstops to prevent a floating state +#define ENDSTOPPULLUPS +#if DISABLED(ENDSTOPPULLUPS) + // Disable ENDSTOPPULLUPS to set pullups individually + //#define ENDSTOPPULLUP_XMAX + //#define ENDSTOPPULLUP_YMAX + //#define ENDSTOPPULLUP_ZMAX + //#define ENDSTOPPULLUP_XMIN + //#define ENDSTOPPULLUP_YMIN + //#define ENDSTOPPULLUP_ZMIN + //#define ENDSTOPPULLUP_ZMIN_PROBE +#endif + +// Enable pulldown for all endstops to prevent a floating state +//#define ENDSTOPPULLDOWNS +#if DISABLED(ENDSTOPPULLDOWNS) + // Disable ENDSTOPPULLDOWNS to set pulldowns individually + //#define ENDSTOPPULLDOWN_XMAX + //#define ENDSTOPPULLDOWN_YMAX + //#define ENDSTOPPULLDOWN_ZMAX + //#define ENDSTOPPULLDOWN_XMIN + //#define ENDSTOPPULLDOWN_YMIN + //#define ENDSTOPPULLDOWN_ZMIN + //#define ENDSTOPPULLDOWN_ZMIN_PROBE +#endif + +// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup). +#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop. +#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop. +#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop. +#define X_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop. +#define Y_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop. +#define Z_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop. +#define Z_MIN_PROBE_ENDSTOP_INVERTING true // Set to true to invert the logic of the probe. + +/** + * Stepper Drivers + * + * These settings allow Marlin to tune stepper driver timing and enable advanced options for + * stepper drivers that support them. You may also override timing options in Configuration_adv.h. + * + * A4988 is assumed for unspecified drivers. + * + * Options: A4988, A5984, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100, + * TMC2130, TMC2130_STANDALONE, TMC2160, TMC2160_STANDALONE, + * TMC2208, TMC2208_STANDALONE, TMC2209, TMC2209_STANDALONE, + * TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE, + * TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE + * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE'] + */ +#define X_DRIVER_TYPE A4988 +#define Y_DRIVER_TYPE A4988 +#define Z_DRIVER_TYPE A4988 +//#define X2_DRIVER_TYPE A4988 +//#define Y2_DRIVER_TYPE A4988 +//#define Z2_DRIVER_TYPE A4988 +//#define Z3_DRIVER_TYPE A4988 +#define E0_DRIVER_TYPE A4988 +//#define E1_DRIVER_TYPE A4988 +//#define E2_DRIVER_TYPE A4988 +//#define E3_DRIVER_TYPE A4988 +//#define E4_DRIVER_TYPE A4988 +//#define E5_DRIVER_TYPE A4988 + +// Enable this feature if all enabled endstop pins are interrupt-capable. +// This will remove the need to poll the interrupt pins, saving many CPU cycles. +//#define ENDSTOP_INTERRUPTS_FEATURE + +/** + * Endstop Noise Threshold + * + * Enable if your probe or endstops falsely trigger due to noise. + * + * - Higher values may affect repeatability or accuracy of some bed probes. + * - To fix noise install a 100nF ceramic capacitor inline with the switch. + * - This feature is not required for common micro-switches mounted on PCBs + * based on the Makerbot design, which already have the 100nF capacitor. + * + * :[2,3,4,5,6,7] + */ +//#define ENDSTOP_NOISE_THRESHOLD 2 + +//============================================================================= +//============================== Movement Settings ============================ +//============================================================================= +// @section motion + +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * With this option each E stepper can have its own factors for the + * following movement settings. If fewer factors are given than the + * total number of extruders, the last value applies to the rest. + */ +//#define DISTINCT_E_FACTORS + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] + */ +#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 94 } + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] + */ +#define DEFAULT_MAX_FEEDRATE { 400, 400, 15, 50 } + +/** + * Default Max Acceleration (change/s) change = mm/s + * (Maximum start speed for accelerated moves) + * Override with M201 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] + */ +#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 3000 } + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 800 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 800 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 1000 // X, Y, Z acceleration for travel (non printing) moves + +/** + * Junction Deviation + * + * Use Junction Deviation instead of traditional Jerk Limiting + * + * See: + * https://reprap.org/forum/read.php?1,739819 + * http://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html + */ +//#define JUNCTION_DEVIATION +#if ENABLED(JUNCTION_DEVIATION) + #define JUNCTION_DEVIATION_MM 0.02 // (mm) Distance from real junction edge +#endif + +/** + * Default Jerk (mm/s) + * Override with M205 X Y Z E + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#if DISABLED(JUNCTION_DEVIATION) + #define DEFAULT_XJERK 10.0 + #define DEFAULT_YJERK 10.0 + #define DEFAULT_ZJERK 0.3 +#endif + +#define DEFAULT_EJERK 5.0 // May be used by Linear Advance + +/** + * S-Curve Acceleration + * + * This option eliminates vibration during printing by fitting a Bézier + * curve to move acceleration, producing much smoother direction changes. + * + * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained + */ +//#define S_CURVE_ACCELERATION + +//=========================================================================== +//============================= Z Probe Options ============================= +//=========================================================================== +// @section probes + +// +// See http://marlinfw.org/docs/configuration/probes.html +// + +/** + * Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + * + * Enable this option for a probe connected to the Z Min endstop pin. + */ +#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +/** + * Z_MIN_PROBE_PIN + * + * Define this pin if the probe is not connected to Z_MIN_PIN. + * If not defined the default pin for the selected MOTHERBOARD + * will be used. Most of the time the default is what you want. + * + * - The simplest option is to use a free endstop connector. + * - Use 5V for powered (usually inductive) sensors. + * + * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin: + * - For simple switches connect... + * - normally-closed switches to GND and D32. + * - normally-open switches to 5V and D32. + * + */ +//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default + +/** + * Probe Type + * + * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. + * Activate one of these to use Auto Bed Leveling below. + */ + +/** + * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe. + * Use G29 repeatedly, adjusting the Z height at each point with movement commands + * or (with LCD_BED_LEVELING) the LCD controller. + */ +//#define PROBE_MANUALLY +//#define MANUAL_PROBE_START_Z 0.2 + +/** + * A Fix-Mounted Probe either doesn't deploy or needs manual deployment. + * (e.g., an inductive probe or a nozzle-based probe-switch.) + */ +//#define FIX_MOUNTED_PROBE + +/** + * Z Servo Probe, such as an endstop switch on a rotating arm. + */ +//#define Z_PROBE_SERVO_NR 0 // Defaults to SERVO 0 connector. +//#define Z_SERVO_ANGLES { 70, 0 } // Z Servo Deploy and Stow angles + +/** + * The BLTouch probe uses a Hall effect sensor and emulates a servo. + */ +//#define BLTOUCH + +/** + * Touch-MI Probe by hotends.fr + * + * This probe is deployed and activated by moving the X-axis to a magnet at the edge of the bed. + * By default, the magnet is assumed to be on the left and activated by a home. If the magnet is + * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position. + * + * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING, + * and a minimum Z_HOMING_HEIGHT of 10. + */ +//#define TOUCH_MI_PROBE +#if ENABLED(TOUCH_MI_PROBE) + #define TOUCH_MI_RETRACT_Z 0.5 // Height at which the probe retracts + //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2) // For a magnet on the right side of the bed + //#define TOUCH_MI_MANUAL_DEPLOY // For manual deploy (LCD menu) +#endif + +// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) +//#define SOLENOID_PROBE + +// A sled-mounted probe like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +// A probe deployed by moving the x-axis, such as the Wilson II's rack-and-pinion probe designed by Marty Rice. +//#define RACK_AND_PINION_PROBE +#if ENABLED(RACK_AND_PINION_PROBE) + #define Z_PROBE_DEPLOY_X X_MIN_POS + #define Z_PROBE_RETRACT_X X_MAX_POS +#endif + +// +// For Z_PROBE_ALLEN_KEY see the Delta example configurations. +// + +/** + * Z Probe to nozzle (X,Y) offset, relative to (0, 0). + * X and Y offsets must be integers. + * + * In the following example the X and Y offsets are both positive: + * #define X_PROBE_OFFSET_FROM_EXTRUDER 10 + * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 + * + * +-- BACK ---+ + * | | + * L | (+) P | R <-- probe (20,20) + * E | | I + * F | (-) N (+) | G <-- nozzle (10,10) + * T | | H + * | (-) | T + * | | + * O-- FRONT --+ + * (0,0) + */ +#define X_PROBE_OFFSET_FROM_EXTRUDER 10 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER 10 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle] + +// Certain types of probes need to stay away from edges +#define MIN_PROBE_EDGE 10 + +// X and Y axis travel speed (mm/m) between probes +#define XY_PROBE_SPEED 8000 + +// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2) +#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z + +// Feedrate (mm/m) for the "accurate" probe of each point +#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2) + +/** + * Multiple Probing + * + * You may get improved results by probing 2 or more times. + * With EXTRA_PROBING the more atypical reading(s) will be disregarded. + * + * A total of 2 does fast/slow probes with a weighted average. + * A total of 3 or more adds more slow probes, taking the average. + */ +//#define MULTIPLE_PROBING 2 +//#define EXTRA_PROBING 1 + +/** + * Z probes require clearance when deploying, stowing, and moving between + * probe points to avoid hitting the bed and other hardware. + * Servo-mounted probes require extra space for the arm to rotate. + * Inductive probes need space to keep from triggering early. + * + * Use these settings to specify the distance (mm) to raise the probe (or + * lower the bed). The values set here apply over and above any (negative) + * probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD. + * Only integer values >= 1 are valid here. + * + * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle. + * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle. + */ +#define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow +#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points +#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes +//#define Z_AFTER_PROBING 5 // Z position after probing is done + +#define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping + +// For M851 give a range for adjusting the Z probe offset +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + +// Enable the M48 repeatability test to test probe accuracy +//#define Z_MIN_PROBE_REPEATABILITY_TEST + +// Before deploy/stow pause for user confirmation +//#define PAUSE_BEFORE_DEPLOY_STOW +#if ENABLED(PAUSE_BEFORE_DEPLOY_STOW) + //#define PAUSE_PROBE_DEPLOY_WHEN_TRIGGERED // For Manual Deploy Allenkey Probe +#endif + +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + +// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 +// :{ 0:'Low', 1:'High' } +#define X_ENABLE_ON 0 +#define Y_ENABLE_ON 0 +#define Z_ENABLE_ON 0 +#define E_ENABLE_ON 0 // For all extruders + +// Disables axis stepper immediately when it's not being used. +// WARNING: When motors turn off there is a chance of losing position accuracy! +#define DISABLE_X false +#define DISABLE_Y false +#define DISABLE_Z false + +// Warn on display about possibly reduced accuracy +//#define DISABLE_REDUCED_ACCURACY_WARNING + +// @section extruder + +#define DISABLE_E false // For all extruders +#define DISABLE_INACTIVE_EXTRUDER // Keep only the active extruder enabled + +// @section machine + +// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way. +#define INVERT_X_DIR true +#define INVERT_Y_DIR false +#define INVERT_Z_DIR false + +// @section extruder + +// For direct drive extruder v9 set to true, for geared extruder set to false. +#define INVERT_E0_DIR true +#define INVERT_E1_DIR false +#define INVERT_E2_DIR false +#define INVERT_E3_DIR false +#define INVERT_E4_DIR false +#define INVERT_E5_DIR false + +// @section homing + +//#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed + +//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off. + +//#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ... + // Be sure you have this distance over your Z_MAX_POS in case. + +// Direction of endstops when homing; 1=MAX, -1=MIN +// :[-1,1] +#define X_HOME_DIR 1 +#define Y_HOME_DIR -1 +#define Z_HOME_DIR -1 + +// @section machine + +// The size of the print bed +#define X_BED_SIZE 125 +#define Y_BED_SIZE 140 + +// Travel limits (mm) after homing, corresponding to endstop positions. +#define X_MIN_POS 0 +#define Y_MIN_POS 0 +#define Z_MIN_POS 0 +#define X_MAX_POS X_BED_SIZE +#define Y_MAX_POS Y_BED_SIZE +#define Z_MAX_POS 100 + +/** + * Software Endstops + * + * - Prevent moves outside the set machine bounds. + * - Individual axes can be disabled, if desired. + * - X and Y only apply to Cartesian robots. + * - Use 'M211' to set software endstops on/off or report current state + */ + +// Min software endstops constrain movement within minimum coordinate bounds +#define MIN_SOFTWARE_ENDSTOPS +#if ENABLED(MIN_SOFTWARE_ENDSTOPS) + #define MIN_SOFTWARE_ENDSTOP_X + #define MIN_SOFTWARE_ENDSTOP_Y + #define MIN_SOFTWARE_ENDSTOP_Z +#endif + +// Max software endstops constrain movement within maximum coordinate bounds +#define MAX_SOFTWARE_ENDSTOPS +#if ENABLED(MAX_SOFTWARE_ENDSTOPS) + #define MAX_SOFTWARE_ENDSTOP_X + #define MAX_SOFTWARE_ENDSTOP_Y + #define MAX_SOFTWARE_ENDSTOP_Z +#endif + +#if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS) + //#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD +#endif + +/** + * Filament Runout Sensors + * Mechanical or opto endstops are used to check for the presence of filament. + * + * RAMPS-based boards use SERVO3_PIN for the first runout sensor. + * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc. + * By default the firmware assumes HIGH=FILAMENT PRESENT. + */ +//#define FILAMENT_RUNOUT_SENSOR +#if ENABLED(FILAMENT_RUNOUT_SENSOR) + #define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each. + #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor. + #define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins. + //#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins. + + // Set one or more commands to execute on filament runout. + // (After 'M412 H' Marlin will ask the host to handle the process.) + #define FILAMENT_RUNOUT_SCRIPT "M600" + + // After a runout is detected, continue printing this length of filament + // before executing the runout script. Useful for a sensor at the end of + // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead. + //#define FILAMENT_RUNOUT_DISTANCE_MM 25 + + #ifdef FILAMENT_RUNOUT_DISTANCE_MM + // Enable this option to use an encoder disc that toggles the runout pin + // as the filament moves. (Be sure to set FILAMENT_RUNOUT_DISTANCE_MM + // large enough to avoid false positives.) + //#define FILAMENT_MOTION_SENSOR + #endif +#endif + +//=========================================================================== +//=============================== Bed Leveling ============================== +//=========================================================================== +// @section calibrate + +/** + * Choose one of the options below to enable G29 Bed Leveling. The parameters + * and behavior of G29 will change depending on your selection. + * + * If using a Probe for Z Homing, enable Z_SAFE_HOMING also! + * + * - AUTO_BED_LEVELING_3POINT + * Probe 3 arbitrary points on the bed (that aren't collinear) + * You specify the XY coordinates of all 3 points. + * The result is a single tilted plane. Best for a flat bed. + * + * - AUTO_BED_LEVELING_LINEAR + * Probe several points in a grid. + * You specify the rectangle and the density of sample points. + * The result is a single tilted plane. Best for a flat bed. + * + * - AUTO_BED_LEVELING_BILINEAR + * Probe several points in a grid. + * You specify the rectangle and the density of sample points. + * The result is a mesh, best for large or uneven beds. + * + * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling) + * A comprehensive bed leveling system combining the features and benefits + * of other systems. UBL also includes integrated Mesh Generation, Mesh + * Validation and Mesh Editing systems. + * + * - MESH_BED_LEVELING + * Probe a grid manually + * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.) + * For machines without a probe, Mesh Bed Leveling provides a method to perform + * leveling in steps so you can manually adjust the Z height at each grid-point. + * With an LCD controller the process is guided step-by-step. + */ +//#define AUTO_BED_LEVELING_3POINT +//#define AUTO_BED_LEVELING_LINEAR +//#define AUTO_BED_LEVELING_BILINEAR +//#define AUTO_BED_LEVELING_UBL +#define MESH_BED_LEVELING + +/** + * Normally G28 leaves leveling disabled on completion. Enable + * this option to have G28 restore the prior leveling state. + */ +//#define RESTORE_LEVELING_AFTER_G28 + +/** + * Enable detailed logging of G28, G29, M48, etc. + * Turn on with the command 'M111 S32'. + * NOTE: Requires a lot of PROGMEM! + */ +//#define DEBUG_LEVELING_FEATURE + +#if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_BILINEAR, AUTO_BED_LEVELING_UBL) + // Gradually reduce leveling correction until a set height is reached, + // at which point movement will be level to the machine's XY plane. + // The height can be set with M420 Z + #define ENABLE_LEVELING_FADE_HEIGHT + + // For Cartesian machines, instead of dividing moves on mesh boundaries, + // split up moves into short segments like a Delta. This follows the + // contours of the bed more closely than edge-to-edge straight moves. + #define SEGMENT_LEVELED_MOVES + #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one) + + /** + * Enable the G26 Mesh Validation Pattern tool. + */ + #define G26_MESH_VALIDATION + #if ENABLED(G26_MESH_VALIDATION) + #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle. + #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool. + #define MESH_TEST_HOTEND_TEMP 205 // (°C) Default nozzle temperature for the G26 Mesh Validation Tool. + #define MESH_TEST_BED_TEMP 60 // (°C) Default bed temperature for the G26 Mesh Validation Tool. + #define G26_XY_FEEDRATE 20 // (mm/s) Feedrate for XY Moves for the G26 Mesh Validation Tool. + #endif + +#endif + +#if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR) + + // Set the number of grid points per dimension. + #define GRID_MAX_POINTS_X 3 + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + // Set the boundaries for probing (where the probe can reach). + //#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE + //#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE)) + //#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE + //#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE)) + + // Probe along the Y axis, advancing X after each column + //#define PROBE_Y_FIRST + + #if ENABLED(AUTO_BED_LEVELING_BILINEAR) + + // Beyond the probed grid, continue the implied tilt? + // Default is to maintain the height of the nearest edge. + //#define EXTRAPOLATE_BEYOND_GRID + + // + // Experimental Subdivision of the grid by Catmull-Rom method. + // Synthesizes intermediate points to produce a more detailed mesh. + // + //#define ABL_BILINEAR_SUBDIVISION + #if ENABLED(ABL_BILINEAR_SUBDIVISION) + // Number of subdivisions between probe points + #define BILINEAR_SUBDIVISIONS 3 + #endif + + #endif + +#elif ENABLED(AUTO_BED_LEVELING_UBL) + + //=========================================================================== + //========================= Unified Bed Leveling ============================ + //=========================================================================== + + //#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh + + #define MESH_INSET 1 // Set Mesh bounds as an inset region of the bed + #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited. + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + #define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle + #define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500 + + //#define UBL_Z_RAISE_WHEN_OFF_MESH 2.5 // When the nozzle is off the mesh, this value is used + // as the Z-Height correction value. + +#elif ENABLED(MESH_BED_LEVELING) + + //=========================================================================== + //=================================== Mesh ================================== + //=========================================================================== + + #define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed + #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited. + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS + +#endif // BED_LEVELING + +/** + * Points to probe for all 3-point Leveling procedures. + * Override if the automatically selected points are inadequate. + */ +#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL) + //#define PROBE_PT_1_X 15 + //#define PROBE_PT_1_Y 180 + //#define PROBE_PT_2_X 15 + //#define PROBE_PT_2_Y 20 + //#define PROBE_PT_3_X 170 + //#define PROBE_PT_3_Y 20 +#endif + +/** + * Add a bed leveling sub-menu for ABL or MBL. + * Include a guided procedure if manual probing is enabled. + */ +#define LCD_BED_LEVELING + +#if ENABLED(LCD_BED_LEVELING) + #define MESH_EDIT_Z_STEP 0.025 // (mm) Step size while manually probing Z axis. + #define LCD_PROBE_Z_RANGE 4 // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment + #define MESH_EDIT_MENU // Add a menu to edit mesh points +#endif + +// Add a menu item to move between bed corners for manual bed adjustment +#define LEVEL_BED_CORNERS + +#if ENABLED(LEVEL_BED_CORNERS) + #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner +#endif + +/** + * Commands to execute at the end of G29 probing. + * Useful to retract or move the Z probe out of the way. + */ +//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" + + +// @section homing + +// The center of the bed is at (X=0, Y=0) +//#define BED_CENTER_AT_0_0 + +// Manually set the home position. Leave these undefined for automatic settings. +// For DELTA this is the top-center of the Cartesian print volume. +//#define MANUAL_X_HOME_POS 0 +//#define MANUAL_Y_HOME_POS 0 +//#define MANUAL_Z_HOME_POS 0 + +// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area. +// +// With this feature enabled: +// +// - Allow Z homing only after X and Y homing AND stepper drivers still enabled. +// - If stepper drivers time out, it will need X and Y homing again before Z homing. +// - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28). +// - Prevent Z homing when the Z probe is outside bed area. +// +//#define Z_SAFE_HOMING + +#if ENABLED(Z_SAFE_HOMING) + #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing when homing all axes (G28). + #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2) // Y point for Z homing when homing all axes (G28). +#endif + +// Homing speeds (mm/m) +#define HOMING_FEEDRATE_XY (50*60) +#define HOMING_FEEDRATE_Z (4*60) + +// Validate that endstops are triggered on homing moves +#define VALIDATE_HOMING_ENDSTOPS + +// @section calibrate + +/** + * Bed Skew Compensation + * + * This feature corrects for misalignment in the XYZ axes. + * + * Take the following steps to get the bed skew in the XY plane: + * 1. Print a test square (e.g., https://www.thingiverse.com/thing:2563185) + * 2. For XY_DIAG_AC measure the diagonal A to C + * 3. For XY_DIAG_BD measure the diagonal B to D + * 4. For XY_SIDE_AD measure the edge A to D + * + * Marlin automatically computes skew factors from these measurements. + * Skew factors may also be computed and set manually: + * + * - Compute AB : SQRT(2*AC*AC+2*BD*BD-4*AD*AD)/2 + * - XY_SKEW_FACTOR : TAN(PI/2-ACOS((AC*AC-AB*AB-AD*AD)/(2*AB*AD))) + * + * If desired, follow the same procedure for XZ and YZ. + * Use these diagrams for reference: + * + * Y Z Z + * ^ B-------C ^ B-------C ^ B-------C + * | / / | / / | / / + * | / / | / / | / / + * | A-------D | A-------D | A-------D + * +-------------->X +-------------->X +-------------->Y + * XY_SKEW_FACTOR XZ_SKEW_FACTOR YZ_SKEW_FACTOR + */ +//#define SKEW_CORRECTION + +#if ENABLED(SKEW_CORRECTION) + // Input all length measurements here: + #define XY_DIAG_AC 282.8427124746 + #define XY_DIAG_BD 282.8427124746 + #define XY_SIDE_AD 200 + + // Or, set the default skew factors directly here + // to override the above measurements: + #define XY_SKEW_FACTOR 0.0 + + //#define SKEW_CORRECTION_FOR_Z + #if ENABLED(SKEW_CORRECTION_FOR_Z) + #define XZ_DIAG_AC 282.8427124746 + #define XZ_DIAG_BD 282.8427124746 + #define YZ_DIAG_AC 282.8427124746 + #define YZ_DIAG_BD 282.8427124746 + #define YZ_SIDE_AD 200 + #define XZ_SKEW_FACTOR 0.0 + #define YZ_SKEW_FACTOR 0.0 + #endif + + // Enable this option for M852 to set skew at runtime + //#define SKEW_CORRECTION_GCODE +#endif + +//============================================================================= +//============================= Additional Features =========================== +//============================================================================= + +// @section extras + +/** + * EEPROM + * + * Persistent storage to preserve configurable settings across reboots. + * + * M500 - Store settings to EEPROM. + * M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes) + * M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.) + */ +#define EEPROM_SETTINGS // Persistent storage with M500 and M501 +//#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release! +#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM. +#if ENABLED(EEPROM_SETTINGS) + #define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors. +#endif + +// +// Host Keepalive +// +// When enabled Marlin will send a busy status message to the host +// every couple of seconds when it can't accept commands. +// +#define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages +#define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113. +#define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating + +// +// M100 Free Memory Watcher +// +//#define M100_FREE_MEMORY_WATCHER // Add M100 (Free Memory Watcher) to debug memory usage + +// +// G20/G21 Inch mode support +// +//#define INCH_MODE_SUPPORT + +// +// M149 Set temperature units support +// +//#define TEMPERATURE_UNITS_SUPPORT + +// @section temperature + +// Preheat Constants +#define PREHEAT_1_LABEL "PLA" +#define PREHEAT_1_TEMP_HOTEND 180 +#define PREHEAT_1_TEMP_BED 70 +#define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255 + +#define PREHEAT_2_LABEL "PETG" +#define PREHEAT_2_TEMP_HOTEND 240 +#define PREHEAT_2_TEMP_BED 80 +#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255 + +/** + * Nozzle Park + * + * Park the nozzle at the given XYZ position on idle or G27. + * + * The "P" parameter controls the action applied to the Z axis: + * + * P0 (Default) If Z is below park Z raise the nozzle. + * P1 Raise the nozzle always to Z-park height. + * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS. + */ +//#define NOZZLE_PARK_FEATURE + +#if ENABLED(NOZZLE_PARK_FEATURE) + // Specify a park position as { X, Y, Z_raise } + #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 } + #define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis) + #define NOZZLE_PARK_Z_FEEDRATE 5 // (mm/s) Z axis feedrate (not used for delta printers) +#endif + +/** + * Clean Nozzle Feature -- EXPERIMENTAL + * + * Adds the G12 command to perform a nozzle cleaning process. + * + * Parameters: + * P Pattern + * S Strokes / Repetitions + * T Triangles (P1 only) + * + * Patterns: + * P0 Straight line (default). This process requires a sponge type material + * at a fixed bed location. "S" specifies strokes (i.e. back-forth motions) + * between the start / end points. + * + * P1 Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the + * number of zig-zag triangles to do. "S" defines the number of strokes. + * Zig-zags are done in whichever is the narrower dimension. + * For example, "G12 P1 S1 T3" will execute: + * + * -- + * | (X0, Y1) | /\ /\ /\ | (X1, Y1) + * | | / \ / \ / \ | + * A | | / \ / \ / \ | + * | | / \ / \ / \ | + * | (X0, Y0) | / \/ \/ \ | (X1, Y0) + * -- +--------------------------------+ + * |________|_________|_________| + * T1 T2 T3 + * + * P2 Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE. + * "R" specifies the radius. "S" specifies the stroke count. + * Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT. + * + * Caveats: The ending Z should be the same as starting Z. + * Attention: EXPERIMENTAL. G-code arguments may change. + * + */ +//#define NOZZLE_CLEAN_FEATURE + +#if ENABLED(NOZZLE_CLEAN_FEATURE) + // Default number of pattern repetitions + #define NOZZLE_CLEAN_STROKES 12 + + // Default number of triangles + #define NOZZLE_CLEAN_TRIANGLES 3 + + // Specify positions as { X, Y, Z } + #define NOZZLE_CLEAN_START_POINT { 30, 30, (Z_MIN_POS + 1)} + #define NOZZLE_CLEAN_END_POINT { 100, 60, (Z_MIN_POS + 1) } + + // Circular pattern radius + #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5 + // Circular pattern circle fragments number + #define NOZZLE_CLEAN_CIRCLE_FN 10 + // Middle point of circle + #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT + + // Move the nozzle to the initial position after cleaning + #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z +#endif + +/** + * Print Job Timer + * + * Automatically start and stop the print job timer on M104/M109/M190. + * + * M104 (hotend, no wait) - high temp = none, low temp = stop timer + * M109 (hotend, wait) - high temp = start timer, low temp = stop timer + * M190 (bed, wait) - high temp = start timer, low temp = none + * + * The timer can also be controlled with the following commands: + * + * M75 - Start the print job timer + * M76 - Pause the print job timer + * M77 - Stop the print job timer + */ +#define PRINTJOB_TIMER_AUTOSTART + +/** + * Print Counter + * + * Track statistical data such as: + * + * - Total print jobs + * - Total successful print jobs + * - Total failed print jobs + * - Total time printing + * + * View the current statistics with M78. + */ +#define PRINTCOUNTER + +//============================================================================= +//============================= LCD and SD support ============================ +//============================================================================= + +// @section lcd + +/** + * LCD LANGUAGE + * + * Select the language to display on the LCD. These languages are available: + * + * en, an, bg, ca, cz, da, de, el, el-gr, es, eu, fi, fr, gl, hr, it, + * jp-kana, ko_KR, nl, pl, pt, pt-br, ru, sk, tr, uk, zh_CN, zh_TW, test + * + * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cz':'Czech', 'da':'Danish', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'jp-kana':'Japanese', 'ko_KR':'Korean (South Korea)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'ru':'Russian', 'sk':'Slovak', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Traditional)', 'test':'TEST' } + */ +#define LCD_LANGUAGE en + +/** + * LCD Character Set + * + * Note: This option is NOT applicable to Graphical Displays. + * + * All character-based LCDs provide ASCII plus one of these + * language extensions: + * + * - JAPANESE ... the most common + * - WESTERN ... with more accented characters + * - CYRILLIC ... for the Russian language + * + * To determine the language extension installed on your controller: + * + * - Compile and upload with LCD_LANGUAGE set to 'test' + * - Click the controller to view the LCD menu + * - The LCD will display Japanese, Western, or Cyrillic text + * + * See http://marlinfw.org/docs/development/lcd_language.html + * + * :['JAPANESE', 'WESTERN', 'CYRILLIC'] + */ +#define DISPLAY_CHARSET_HD44780 WESTERN + +/** + * Info Screen Style (0:Classic, 1:Prusa) + * + * :[0:'Classic', 1:'Prusa'] + */ +#define LCD_INFO_SCREEN_STYLE 0 + +/** + * SD CARD + * + * SD Card support is disabled by default. If your controller has an SD slot, + * you must uncomment the following option or it won't work. + * + */ +#define SDSUPPORT + +/** + * SD CARD: SPI SPEED + * + * Enable one of the following items for a slower SPI transfer speed. + * This may be required to resolve "volume init" errors. + */ +//#define SPI_SPEED SPI_HALF_SPEED +//#define SPI_SPEED SPI_QUARTER_SPEED +//#define SPI_SPEED SPI_EIGHTH_SPEED + +/** + * SD CARD: ENABLE CRC + * + * Use CRC checks and retries on the SD communication. + */ +//#define SD_CHECK_AND_RETRY + +/** + * LCD Menu Items + * + * Disable all menus and only display the Status Screen, or + * just remove some extraneous menu items to recover space. + */ +//#define NO_LCD_MENUS +//#define SLIM_LCD_MENUS + +// +// ENCODER SETTINGS +// +// This option overrides the default number of encoder pulses needed to +// produce one step. Should be increased for high-resolution encoders. +// +#define ENCODER_PULSES_PER_STEP 4 + +// +// Use this option to override the number of step signals required to +// move between next/prev menu items. +// +#define ENCODER_STEPS_PER_MENU_ITEM 1 + +/** + * Encoder Direction Options + * + * Test your encoder's behavior first with both options disabled. + * + * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION. + * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION. + * Reversed Value Editing only? Enable BOTH options. + */ + +// +// This option reverses the encoder direction everywhere. +// +// Set this option if CLOCKWISE causes values to DECREASE +// +//#define REVERSE_ENCODER_DIRECTION + +// +// This option reverses the encoder direction for navigating LCD menus. +// +// If CLOCKWISE normally moves DOWN this makes it go UP. +// If CLOCKWISE normally moves UP this makes it go DOWN. +// +//#define REVERSE_MENU_DIRECTION + +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + +// +// Individual Axis Homing +// +// Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu. +// +//#define INDIVIDUAL_AXIS_HOMING_MENU + +// +// SPEAKER/BUZZER +// +// If you have a speaker that can produce tones, enable it here. +// By default Marlin assumes you have a buzzer with a fixed frequency. +// +#define SPEAKER + +// +// The duration and frequency for the UI feedback sound. +// Set these to 0 to disable audio feedback in the LCD menus. +// +// Note: Test audio output with the G-Code: +// M300 S P +// +//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 2 +//#define LCD_FEEDBACK_FREQUENCY_HZ 5000 + +//============================================================================= +//======================== LCD / Controller Selection ========================= +//======================== (Character-based LCDs) ========================= +//============================================================================= + +// +// RepRapDiscount Smart Controller. +// http://reprap.org/wiki/RepRapDiscount_Smart_Controller +// +// Note: Usually sold with a white PCB. +// +//#define REPRAP_DISCOUNT_SMART_CONTROLLER + +// +// Original RADDS LCD Display+Encoder+SDCardReader +// http://doku.radds.org/dokumentation/lcd-display/ +// +//#define RADDS_DISPLAY + +// +// ULTIMAKER Controller. +// +//#define ULTIMAKERCONTROLLER + +// +// ULTIPANEL as seen on Thingiverse. +// +//#define ULTIPANEL + +// +// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3) +// http://reprap.org/wiki/PanelOne +// +//#define PANEL_ONE + +// +// GADGETS3D G3D LCD/SD Controller +// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel +// +// Note: Usually sold with a blue PCB. +// +//#define G3D_PANEL + +// +// RigidBot Panel V1.0 +// http://www.inventapart.com/ +// +//#define RIGIDBOT_PANEL + +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// ANET and Tronxy 20x4 Controller +// +//#define ZONESTAR_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin. + // This LCD is known to be susceptible to electrical interference + // which scrambles the display. Pressing any button clears it up. + // This is a LCD2004 display with 5 analog buttons. + +// +// Generic 16x2, 16x4, 20x2, or 20x4 character-based LCD. +// +//#define ULTRA_LCD + +//============================================================================= +//======================== LCD / Controller Selection ========================= +//===================== (I2C and Shift-Register LCDs) ===================== +//============================================================================= + +// +// CONTROLLER TYPE: I2C +// +// Note: These controllers require the installation of Arduino's LiquidCrystal_I2C +// library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C +// + +// +// Elefu RA Board Control Panel +// http://www.elefu.com/index.php?route=product/product&product_id=53 +// +//#define RA_CONTROL_PANEL + +// +// Sainsmart (YwRobot) LCD Displays +// +// These require F.Malpartida's LiquidCrystal_I2C library +// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home +// +//#define LCD_SAINSMART_I2C_1602 +//#define LCD_SAINSMART_I2C_2004 + +// +// Generic LCM1602 LCD adapter +// +//#define LCM1602 + +// +// PANELOLU2 LCD with status LEDs, +// separate encoder and click inputs. +// +// Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later. +// For more info: https://github.com/lincomatic/LiquidTWI2 +// +// Note: The PANELOLU2 encoder click input can either be directly connected to +// a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1). +// +//#define LCD_I2C_PANELOLU2 + +// +// Panucatt VIKI LCD with status LEDs, +// integrated click & L/R/U/D buttons, separate encoder inputs. +// +//#define LCD_I2C_VIKI + +// +// CONTROLLER TYPE: Shift register panels +// + +// +// 2-wire Non-latching LCD SR from https://goo.gl/aJJ4sH +// LCD configuration: http://reprap.org/wiki/SAV_3D_LCD +// +//#define SAV_3DLCD + +// +// 3-wire SR LCD with strobe using 74HC4094 +// https://github.com/mikeshub/SailfishLCD +// Uses the code directly from Sailfish +// +//#define FF_INTERFACEBOARD + +//============================================================================= +//======================= LCD / Controller Selection ======================= +//========================= (Graphical LCDs) ======================== +//============================================================================= + +// +// CONTROLLER TYPE: Graphical 128x64 (DOGM) +// +// IMPORTANT: The U8glib library is required for Graphical Display! +// https://github.com/olikraus/U8glib_Arduino +// + +// +// RepRapDiscount FULL GRAPHIC Smart Controller +// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller +// +//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER + +// +// ReprapWorld Graphical LCD +// https://reprapworld.com/?products_details&products_id/1218 +// +//#define REPRAPWORLD_GRAPHICAL_LCD + +// +// Activate one of these if you have a Panucatt Devices +// Viki 2.0 or mini Viki with Graphic LCD +// http://panucatt.com +// +//#define VIKI2 +//#define miniVIKI + +// +// MakerLab Mini Panel with graphic +// controller and SD support - http://reprap.org/wiki/Mini_panel +// +//#define MINIPANEL + +// +// MaKr3d Makr-Panel with graphic controller and SD support. +// http://reprap.org/wiki/MaKr3d_MaKrPanel +// +//#define MAKRPANEL + +// +// Adafruit ST7565 Full Graphic Controller. +// https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/ +// +//#define ELB_FULL_GRAPHIC_CONTROLLER + +// +// BQ LCD Smart Controller shipped by +// default with the BQ Hephestos 2 and Witbox 2. +// +//#define BQ_LCD_SMART_CONTROLLER + +// +// Cartesio UI +// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// +//#define CARTESIO_UI + +// +// LCD for Melzi Card with Graphical LCD +// +//#define LCD_FOR_MELZI + +// +// Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder +// https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) +// +//#define ULTI_CONTROLLER + +// +// MKS MINI12864 with graphic controller and SD support +// https://reprap.org/wiki/MKS_MINI_12864 +// +#define MKS_MINI_12864 + +// +// FYSETC variant of the MINI12864 graphic controller with SD support +// https://wiki.fysetc.com/Mini12864_Panel/ +// +//#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default +//#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) +//#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// ANET and Tronxy Graphical Controller +// +// Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6 +// A clone of the RepRapDiscount full graphics display but with +// different pins/wiring (see pins_ANET_10.h). +// +//#define ANET_FULL_GRAPHICS_LCD + +// +// AZSMZ 12864 LCD with SD +// https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html +// +//#define AZSMZ_12864 + +// +// Silvergate GLCD controller +// http://github.com/android444/Silvergate +// +//#define SILVER_GATE_GLCD_CONTROLLER + +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + +//============================================================================= +//========================== Extensible UI Displays =========================== +//============================================================================= + +// +// DGUS Touch Display with DWIN OS +// +//#define DGUS_LCD + +// +// Touch-screen LCD for Malyan M200 printers +// +//#define MALYAN_LCD + +// +// Third-party or vendor-customized controller interfaces. +// Sources should be installed in 'src/lcd/extensible_ui'. +// +//#define EXTENSIBLE_UI + +//============================================================================= +//=============================== Graphical TFTs ============================== +//============================================================================= + +// +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) +// +//#define FSMC_GRAPHICAL_TFT + +//============================================================================= +//============================ Other Controllers ============================ +//============================================================================= + +// +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 +// +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif + +// +// RepRapWorld REPRAPWORLD_KEYPAD v1.1 +// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626 +// +// REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key +// is pressed, a value of 10.0 means 10mm per click. +// +//#define REPRAPWORLD_KEYPAD +//#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 + +//============================================================================= +//=============================== Extra Features ============================== +//============================================================================= + +// @section extras + +// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino +//#define FAST_PWM_FAN + +// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency +// which is not as annoying as with the hardware PWM. On the other hand, if this frequency +// is too low, you should also increment SOFT_PWM_SCALE. +#define FAN_SOFT_PWM + +// Incrementing this by 1 will double the software PWM frequency, +// affecting heaters, and the fan if FAN_SOFT_PWM is enabled. +// However, control resolution will be halved for each increment; +// at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] +#define SOFT_PWM_SCALE 0 + +// If SOFT_PWM_SCALE is set to a value higher than 0, dithering can +// be used to mitigate the associated resolution loss. If enabled, +// some of the PWM cycles are stretched so on average the desired +// duty cycle is attained. +//#define SOFT_PWM_DITHER + +// Temperature status LEDs that display the hotend and bed temperature. +// If all hotends, bed temperature, and target temperature are under 54C +// then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis) +//#define TEMP_STAT_LEDS + +// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure +//#define SF_ARC_FIX + +// Support for the BariCUDA Paste Extruder +//#define BARICUDA + +// Support for BlinkM/CyzRgb +//#define BLINKM + +// Support for PCA9632 PWM LED driver +//#define PCA9632 + +// Support for PCA9533 PWM LED driver +// https://github.com/mikeshub/SailfishRGB_LED +//#define PCA9533 + +/** + * RGB LED / LED Strip Control + * + * Enable support for an RGB LED connected to 5V digital pins, or + * an RGB Strip connected to MOSFETs controlled by digital pins. + * + * Adds the M150 command to set the LED (or LED strip) color. + * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of + * luminance values can be set from 0 to 255. + * For Neopixel LED an overall brightness parameter is also available. + * + * *** CAUTION *** + * LED Strips require a MOSFET Chip between PWM lines and LEDs, + * as the Arduino cannot handle the current the LEDs will require. + * Failure to follow this precaution can destroy your Arduino! + * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * more current than the Arduino 5V linear regulator can produce. + * *** CAUTION *** + * + * LED Type. Enable only one of the following two options. + * + */ +//#define RGB_LED +//#define RGBW_LED + +#if EITHER(RGB_LED, RGBW_LED) + //#define RGB_LED_R_PIN 34 + //#define RGB_LED_G_PIN 43 + //#define RGB_LED_B_PIN 35 + //#define RGB_LED_W_PIN -1 +#endif + +// Support for Adafruit Neopixel LED driver +//#define NEOPIXEL_LED +#if ENABLED(NEOPIXEL_LED) + #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. + #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) + //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup + + // Use a single Neopixel LED for static (background) lighting + //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use + //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W +#endif + +/** + * Printer Event LEDs + * + * During printing, the LEDs will reflect the printer status: + * + * - Gradually change from blue to violet as the heated bed gets to target temp + * - Gradually change from violet to red as the hotend gets to temperature + * - Change to white to illuminate work surface + * - Change to green once print has finished + * - Turn off after the print has finished and the user has pushed a button + */ +#if ANY(BLINKM, RGB_LED, RGBW_LED, PCA9632, PCA9533, NEOPIXEL_LED) + #define PRINTER_EVENT_LEDS +#endif + +/** + * R/C SERVO support + * Sponsored by TrinityLabs, Reworked by codexmas + */ + +/** + * Number of servos + * + * For some servo-related options NUM_SERVOS will be set automatically. + * Set this manually if there are extra servos needing manual control. + * Leave undefined or set to 0 to entirely disable the servo subsystem. + */ +//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command + +// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. +// 300ms is a good value but you can try less delay. +// If the servo can't reach the requested position, increase it. +#define SERVO_DELAY { 300 } + +// Only power servos during movement, otherwise leave off to prevent jitter +//#define DEACTIVATE_SERVOS_AFTER_MOVE + +// Allow servo angle to be edited and saved to EEPROM +//#define EDITABLE_SERVO_ANGLES diff --git a/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h b/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h new file mode 100644 index 0000000000..d0ff439d7a --- /dev/null +++ b/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h @@ -0,0 +1,2562 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Configuration_adv.h + * + * Advanced settings. + * Only change these if you know exactly what you're doing. + * Some of these settings can damage your printer if improperly set! + * + * Basic settings can be found in Configuration.h + * + */ +#define CONFIGURATION_ADV_H_VERSION 020000 + +// @section temperature + +//=========================================================================== +//=============================Thermal Settings ============================ +//=========================================================================== + +// +// Custom Thermistor 1000 parameters +// +#if TEMP_SENSOR_0 == 1000 + #define HOTEND0_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND0_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND0_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_1 == 1000 + #define HOTEND1_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND1_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND1_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_2 == 1000 + #define HOTEND2_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND2_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND2_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_3 == 1000 + #define HOTEND3_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND3_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND3_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_4 == 1000 + #define HOTEND4_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND4_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND4_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_5 == 1000 + #define HOTEND5_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND5_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND5_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_BED == 1000 + #define BED_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define BED_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define BED_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_CHAMBER == 1000 + #define CHAMBER_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define CHAMBER_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define CHAMBER_BETA 3950 // Beta value +#endif + +// +// Hephestos 2 24V heated bed upgrade kit. +// https://store.bq.com/en/heated-bed-kit-hephestos2 +// +//#define HEPHESTOS2_HEATED_BED_KIT +#if ENABLED(HEPHESTOS2_HEATED_BED_KIT) + #undef TEMP_SENSOR_BED + #define TEMP_SENSOR_BED 70 + #define HEATER_BED_INVERTING true +#endif + +/** + * Heated Chamber settings + */ +#if TEMP_SENSOR_CHAMBER + #define CHAMBER_MINTEMP 5 + #define CHAMBER_MAXTEMP 60 + #define TEMP_CHAMBER_HYSTERESIS 1 // (°C) Temperature proximity considered "close enough" to the target + //#define CHAMBER_LIMIT_SWITCHING + //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin + //#define HEATER_CHAMBER_INVERTING false +#endif + +#if DISABLED(PIDTEMPBED) + #define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control + #if ENABLED(BED_LIMIT_SWITCHING) + #define BED_HYSTERESIS 2 // Only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS + #endif +#endif + +/** + * Thermal Protection provides additional protection to your printer from damage + * and fire. Marlin always includes safe min and max temperature ranges which + * protect against a broken or disconnected thermistor wire. + * + * The issue: If a thermistor falls out, it will report the much lower + * temperature of the air in the room, and the the firmware will keep + * the heater on. + * + * The solution: Once the temperature reaches the target, start observing. + * If the temperature stays too far below the target (hysteresis) for too + * long (period), the firmware will halt the machine as a safety precaution. + * + * If you get false positives for "Thermal Runaway", increase + * THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD + */ +#if ENABLED(THERMAL_PROTECTION_HOTENDS) + #define THERMAL_PROTECTION_PERIOD 40 // Seconds + #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius + + //#define ADAPTIVE_FAN_SLOWING // Slow part cooling fan if temperature drops + #if BOTH(ADAPTIVE_FAN_SLOWING, PIDTEMP) + //#define NO_FAN_SLOWING_IN_PID_TUNING // Don't slow fan speed during M303 + #endif + + /** + * Whenever an M104, M109, or M303 increases the target temperature, the + * firmware will wait for the WATCH_TEMP_PERIOD to expire. If the temperature + * hasn't increased by WATCH_TEMP_INCREASE degrees, the machine is halted and + * requires a hard reset. This test restarts with any M104/M109/M303, but only + * if the current temperature is far enough below the target for a reliable + * test. + * + * If you get false positives for "Heating failed", increase WATCH_TEMP_PERIOD + * and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set + * below 2. + */ + #define WATCH_TEMP_PERIOD 20 // Seconds + #define WATCH_TEMP_INCREASE 2 // Degrees Celsius +#endif + +/** + * Thermal Protection parameters for the bed are just as above for hotends. + */ +#if ENABLED(THERMAL_PROTECTION_BED) + #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds + #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius + + /** + * As described above, except for the bed (M140/M190/M303). + */ + #define WATCH_BED_TEMP_PERIOD 60 // Seconds + #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius +#endif + +/** + * Thermal Protection parameters for the heated chamber. + */ +#if ENABLED(THERMAL_PROTECTION_CHAMBER) + #define THERMAL_PROTECTION_CHAMBER_PERIOD 20 // Seconds + #define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius + + /** + * Heated chamber watch settings (M141/M191). + */ + #define WATCH_CHAMBER_TEMP_PERIOD 60 // Seconds + #define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius +#endif + +#if ENABLED(PIDTEMP) + // Add an experimental additional term to the heater power, proportional to the extrusion speed. + // A well-chosen Kc value should add just enough power to melt the increased material volume. + //#define PID_EXTRUSION_SCALING + #if ENABLED(PID_EXTRUSION_SCALING) + #define DEFAULT_Kc (100) //heating power=Kc*(e_speed) + #define LPQ_MAX_LEN 50 + #endif +#endif + +/** + * Automatic Temperature: + * The hotend target temperature is calculated by all the buffered lines of gcode. + * The maximum buffered steps/sec of the extruder motor is called "se". + * Start autotemp mode with M109 S B F + * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by + * mintemp and maxtemp. Turn this off by executing M109 without F* + * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp. + * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode + */ +#define AUTOTEMP +#if ENABLED(AUTOTEMP) + #define AUTOTEMP_OLDWEIGHT 0.98 +#endif + +// Show extra position information in M114 +//#define M114_DETAIL + +// Show Temperature ADC value +// Enable for M105 to include ADC values read from temperature sensors. +//#define SHOW_TEMP_ADC_VALUES + +/** + * High Temperature Thermistor Support + * + * Thermistors able to support high temperature tend to have a hard time getting + * good readings at room and lower temperatures. This means HEATER_X_RAW_LO_TEMP + * will probably be caught when the heating element first turns on during the + * preheating process, which will trigger a min_temp_error as a safety measure + * and force stop everything. + * To circumvent this limitation, we allow for a preheat time (during which, + * min_temp_error won't be triggered) and add a min_temp buffer to handle + * aberrant readings. + * + * If you want to enable this feature for your hotend thermistor(s) + * uncomment and set values > 0 in the constants below + */ + +// The number of consecutive low temperature errors that can occur +// before a min_temp_error is triggered. (Shouldn't be more than 10.) +//#define MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED 0 + +// The number of milliseconds a hotend will preheat before starting to check +// the temperature. This value should NOT be set to the time it takes the +// hot end to reach the target temperature, but the time it takes to reach +// the minimum temperature your thermistor can read. The lower the better/safer. +// This shouldn't need to be more than 30 seconds (30000) +//#define MILLISECONDS_PREHEAT_TIME 0 + +// @section extruder + +// Extruder runout prevention. +// If the machine is idle and the temperature over MINTEMP +// then extrude some filament every couple of SECONDS. +//#define EXTRUDER_RUNOUT_PREVENT +#if ENABLED(EXTRUDER_RUNOUT_PREVENT) + #define EXTRUDER_RUNOUT_MINTEMP 190 + #define EXTRUDER_RUNOUT_SECONDS 30 + #define EXTRUDER_RUNOUT_SPEED 1500 // (mm/m) + #define EXTRUDER_RUNOUT_EXTRUDE 5 // (mm) +#endif + +// @section temperature + +// Calibration for AD595 / AD8495 sensor to adjust temperature measurements. +// The final temperature is calculated as (measuredTemp * GAIN) + OFFSET. +#define TEMP_SENSOR_AD595_OFFSET 0.0 +#define TEMP_SENSOR_AD595_GAIN 1.0 +#define TEMP_SENSOR_AD8495_OFFSET 0.0 +#define TEMP_SENSOR_AD8495_GAIN 1.0 + +/** + * Controller Fan + * To cool down the stepper drivers and MOSFETs. + * + * The fan will turn on automatically whenever any stepper is enabled + * and turn off after a set period after all steppers are turned off. + */ +//#define USE_CONTROLLER_FAN +#if ENABLED(USE_CONTROLLER_FAN) + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled + #define CONTROLLERFAN_SPEED 255 // 255 == full speed +#endif + +// When first starting the main fan, run it at full speed for the +// given number of milliseconds. This gets the fan spinning reliably +// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) +//#define FAN_KICKSTART_TIME 100 + +/** + * PWM Fan Scaling + * + * Define the min/max speeds for PWM fans (as set with M106). + * + * With these options the M106 0-255 value range is scaled to a subset + * to ensure that the fan has enough power to spin, or to run lower + * current fans with higher current. (e.g., 5V/12V fans with 12V/24V) + * Value 0 always turns off the fan. + * + * Define one or both of these to override the default 0-255 range. + */ +//#define FAN_MIN_PWM 50 +//#define FAN_MAX_PWM 128 + +/** + * FAST PWM FAN Settings + * + * Use to change the FAST FAN PWM frequency (if enabled in Configuration.h) + * Combinations of PWM Modes, prescale values and TOP resolutions are used internally to produce a + * frequency as close as possible to the desired frequency. + * + * FAST_PWM_FAN_FREQUENCY [undefined by default] + * Set this to your desired frequency. + * If left undefined this defaults to F = F_CPU/(2*255*1) + * ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers + * These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required + * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior. + * + * USE_OCR2A_AS_TOP [undefined by default] + * Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2: + * 16MHz MCUs: [62.5KHz, 31.4KHz (default), 7.8KHz, 3.92KHz, 1.95KHz, 977Hz, 488Hz, 244Hz, 60Hz, 122Hz, 30Hz] + * 20MHz MCUs: [78.1KHz, 39.2KHz (default), 9.77KHz, 4.9KHz, 2.44KHz, 1.22KHz, 610Hz, 305Hz, 153Hz, 76Hz, 38Hz] + * A greater range can be achieved by enabling USE_OCR2A_AS_TOP. But note that this option blocks the use of + * PWM on pin OC2A. Only use this option if you don't need PWM on 0C2A. (Check your schematic.) + * USE_OCR2A_AS_TOP sacrifices duty cycle control resolution to achieve this broader range of frequencies. + */ +#if ENABLED(FAST_PWM_FAN) + //#define FAST_PWM_FAN_FREQUENCY 31400 + //#define USE_OCR2A_AS_TOP +#endif + +// @section extruder + +/** + * Extruder cooling fans + * + * Extruder auto fans automatically turn on when their extruders' + * temperatures go above EXTRUDER_AUTO_FAN_TEMPERATURE. + * + * Your board's pins file specifies the recommended pins. Override those here + * or set to -1 to disable completely. + * + * Multiple extruders can be assigned to the same pin in which case + * the fan will turn on when any selected extruder is above the threshold. + */ +#define E0_AUTO_FAN_PIN -1 +#define E1_AUTO_FAN_PIN -1 +#define E2_AUTO_FAN_PIN -1 +#define E3_AUTO_FAN_PIN -1 +#define E4_AUTO_FAN_PIN -1 +#define E5_AUTO_FAN_PIN -1 +#define CHAMBER_AUTO_FAN_PIN -1 + +#define EXTRUDER_AUTO_FAN_TEMPERATURE 50 +#define EXTRUDER_AUTO_FAN_SPEED 255 // 255 == full speed +#define CHAMBER_AUTO_FAN_TEMPERATURE 30 +#define CHAMBER_AUTO_FAN_SPEED 255 + +/** + * Part-Cooling Fan Multiplexer + * + * This feature allows you to digitally multiplex the fan output. + * The multiplexer is automatically switched at tool-change. + * Set FANMUX[012]_PINs below for up to 2, 4, or 8 multiplexed fans. + */ +#define FANMUX0_PIN -1 +#define FANMUX1_PIN -1 +#define FANMUX2_PIN -1 + +/** + * M355 Case Light on-off / brightness + */ +//#define CASE_LIGHT_ENABLE +#if ENABLED(CASE_LIGHT_ENABLE) + //#define CASE_LIGHT_PIN 4 // Override the default pin if needed + #define INVERT_CASE_LIGHT false // Set true if Case Light is ON when pin is LOW + #define CASE_LIGHT_DEFAULT_ON true // Set default power-up state on + #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105 // Set default power-up brightness (0-255, requires PWM pin) + //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu + //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. + //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) + #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } + #endif +#endif + +// @section homing + +// If you want endstops to stay on (by default) even when not homing +// enable this option. Override at any time with M120, M121. +//#define ENDSTOPS_ALWAYS_ON_DEFAULT + +// @section extras + +//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats. + +// Employ an external closed loop controller. Override pins here if needed. +//#define EXTERNAL_CLOSED_LOOP_CONTROLLER +#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER) + //#define CLOSED_LOOP_ENABLE_PIN -1 + //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1 +#endif + +/** + * Dual Steppers / Dual Endstops + * + * This section will allow you to use extra E drivers to drive a second motor for X, Y, or Z axes. + * + * For example, set X_DUAL_STEPPER_DRIVERS setting to use a second motor. If the motors need to + * spin in opposite directions set INVERT_X2_VS_X_DIR. If the second motor needs its own endstop + * set X_DUAL_ENDSTOPS. This can adjust for "racking." Use X2_USE_ENDSTOP to set the endstop plug + * that should be used for the second endstop. Extra endstops will appear in the output of 'M119'. + * + * Use X_DUAL_ENDSTOP_ADJUSTMENT to adjust for mechanical imperfection. After homing both motors + * this offset is applied to the X2 motor. To find the offset home the X axis, and measure the error + * in X2. Dual endstop offsets can be set at runtime with 'M666 X Y Z'. + */ + +//#define X_DUAL_STEPPER_DRIVERS +#if ENABLED(X_DUAL_STEPPER_DRIVERS) + #define INVERT_X2_VS_X_DIR true // Set 'true' if X motors should rotate in opposite directions + //#define X_DUAL_ENDSTOPS + #if ENABLED(X_DUAL_ENDSTOPS) + #define X2_USE_ENDSTOP _XMAX_ + #define X_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Y_DUAL_STEPPER_DRIVERS +#if ENABLED(Y_DUAL_STEPPER_DRIVERS) + #define INVERT_Y2_VS_Y_DIR true // Set 'true' if Y motors should rotate in opposite directions + //#define Y_DUAL_ENDSTOPS + #if ENABLED(Y_DUAL_ENDSTOPS) + #define Y2_USE_ENDSTOP _YMAX_ + #define Y_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Z_DUAL_STEPPER_DRIVERS +#if ENABLED(Z_DUAL_STEPPER_DRIVERS) + //#define Z_DUAL_ENDSTOPS + #if ENABLED(Z_DUAL_ENDSTOPS) + #define Z2_USE_ENDSTOP _XMAX_ + #define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Z_TRIPLE_STEPPER_DRIVERS +#if ENABLED(Z_TRIPLE_STEPPER_DRIVERS) + //#define Z_TRIPLE_ENDSTOPS + #if ENABLED(Z_TRIPLE_ENDSTOPS) + #define Z2_USE_ENDSTOP _XMAX_ + #define Z3_USE_ENDSTOP _YMAX_ + #define Z_TRIPLE_ENDSTOPS_ADJUSTMENT2 0 + #define Z_TRIPLE_ENDSTOPS_ADJUSTMENT3 0 + #endif +#endif + +/** + * Dual X Carriage + * + * This setup has two X carriages that can move independently, each with its own hotend. + * The carriages can be used to print an object with two colors or materials, or in + * "duplication mode" it can print two identical or X-mirrored objects simultaneously. + * The inactive carriage is parked automatically to prevent oozing. + * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. + * By default the X2 stepper is assigned to the first unused E plug on the board. + * + * The following Dual X Carriage modes can be selected with M605 S: + * + * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel + * results as long as it supports dual X-carriages. (M605 S0) + * + * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so + * that additional slicer support is not required. (M605 S1) + * + * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with + * the first X-carriage and extruder, to print 2 copies of the same object at the same time. + * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and + * follow with M605 S2 to initiate duplicated movement. + * + * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates + * the movement of the first except the second extruder is reversed in the X axis. + * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and + * follow with M605 S3 to initiate mirrored movement. + */ +//#define DUAL_X_CARRIAGE +#if ENABLED(DUAL_X_CARRIAGE) + #define X1_MIN_POS X_MIN_POS // Set to X_MIN_POS + #define X1_MAX_POS X_BED_SIZE // Set a maximum so the first X-carriage can't hit the parked second X-carriage + #define X2_MIN_POS 80 // Set a minimum to ensure the second X-carriage can't hit the parked first X-carriage + #define X2_MAX_POS 353 // Set this to the distance between toolheads when both heads are homed + #define X2_HOME_DIR 1 // Set to 1. The second X-carriage always homes to the maximum endstop position + #define X2_HOME_POS X2_MAX_POS // Default X2 home position. Set to X2_MAX_POS. + // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software + // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops + // without modifying the firmware (through the "M218 T1 X???" command). + // Remember: you should set the second extruder x-offset to 0 in your slicer. + + // This is the default power-up mode which can be later using M605. + #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_AUTO_PARK_MODE + + // Default x offset in duplication mode (typically set to half print bed width) + #define DEFAULT_DUPLICATION_X_OFFSET 100 + +#endif // DUAL_X_CARRIAGE + +// Activate a solenoid on the active extruder with M380. Disable all with M381. +// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid. +//#define EXT_SOLENOID + +// @section homing + +// Homing hits each endstop, retracts by these distances, then does a slower bump. +#define X_HOME_BUMP_MM 5 +#define Y_HOME_BUMP_MM 5 +#define Z_HOME_BUMP_MM 2 +#define HOMING_BUMP_DIVISOR { 2, 2, 4 } // Re-Bump Speed Divisor (Divides the Homing Feedrate) +#define QUICK_HOME // If homing includes X and Y, do a diagonal move initially +//#define HOMING_BACKOFF_MM { 2, 2, 2 } // (mm) Move away from the endstops after homing + +// When G28 is called, this option will make Y home before X +//#define HOME_Y_BEFORE_X + +// Enable this if X or Y can't home without homing the other axis first. +//#define CODEPENDENT_XY_HOMING + +#if ENABLED(BLTOUCH) + /** + * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES + * Do not activate settings that the probe might not understand. Clones might misunderstand + * advanced commands. + * + * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then + * check the wiring of the BROWN, RED and ORANGE wires. + * + * Note: If the trigger signal of your probe is not being recognized, it has been very often + * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable" + * like they would be with a real switch. So please check the wiring first. + * + * Settings for all BLTouch and clone probes: + */ + + // Safety: The probe needs time to recognize the command. + // Minimum command delay (ms). Enable and increase if needed. + //#define BLTOUCH_DELAY 500 + + /** + * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones: + */ + + // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful + // in special cases, like noisy or filtered input configurations. + //#define BLTOUCH_FORCE_SW_MODE + + /** + * Settings for BLTouch Smart 3.0 and 3.1 + * Summary: + * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes + * - High-Speed mode + * - Disable LCD voltage options + */ + + /** + * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller! + * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup. + * If disabled, OD mode is the hard-coded default on 3.0 + * On startup, Marlin will compare its eeprom to this vale. If the selected mode + * differs, a mode set eeprom write will be completed at initialization. + * Use the option below to force an eeprom write to a V3.1 probe regardless. + */ + //#define BLTOUCH_SET_5V_MODE + + /** + * Safety: Activate if connecting a probe with an unknown voltage mode. + * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0 + * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write ) + * To preserve the life of the probe, use this once then turn it off and re-flash. + */ + //#define BLTOUCH_FORCE_MODE_SET + + /** + * Use "HIGH SPEED" mode for probing. + * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems. + * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function + * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state. + */ + //#define BLTOUCH_HS_MODE + + // Safety: Enable voltage mode settings in the LCD menu. + //#define BLTOUCH_LCD_VOLTAGE_MENU + +#endif // BLTOUCH + +/** + * Z Steppers Auto-Alignment + * Add the G34 command to align multiple Z steppers using a bed probe. + */ +//#define Z_STEPPER_AUTO_ALIGN +#if ENABLED(Z_STEPPER_AUTO_ALIGN) + // Define probe X and Y positions for Z1, Z2 [, Z3] + #define Z_STEPPER_ALIGN_X { 10, 150, 290 } + #define Z_STEPPER_ALIGN_Y { 290, 10, 290 } + // Set number of iterations to align + #define Z_STEPPER_ALIGN_ITERATIONS 3 + // Enable to restore leveling setup after operation + #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + + // Use the amplification factor to de-/increase correction step. + // In case the stepper (spindle) position is further out than the test point + // Use a value > 1. NOTE: This may cause instability + #define Z_STEPPER_ALIGN_AMP 1.0 + // Stop criterion. If the accuracy is better than this stop iterating early + #define Z_STEPPER_ALIGN_ACC 0.02 +#endif + +// @section machine + +#define AXIS_RELATIVE_MODES { false, false, false, false } + +// Add a Duplicate option for well-separated conjoined nozzles +//#define MULTI_NOZZLE_DUPLICATION + +// By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step. +#define INVERT_X_STEP_PIN false +#define INVERT_Y_STEP_PIN false +#define INVERT_Z_STEP_PIN false +#define INVERT_E_STEP_PIN false + +// Default stepper release if idle. Set to 0 to deactivate. +// Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true. +// Time can be set by M18 and M84. +#define DEFAULT_STEPPER_DEACTIVE_TIME 120 +#define DISABLE_INACTIVE_X true +#define DISABLE_INACTIVE_Y true +#define DISABLE_INACTIVE_Z true // Set to false if the nozzle will fall down on your printed part when print has finished. +#define DISABLE_INACTIVE_E true + +#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate +#define DEFAULT_MINTRAVELFEEDRATE 0.0 + +//#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated + +// @section lcd + +#if EITHER(ULTIPANEL, EXTENSIBLE_UI) + #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) + #if ENABLED(ULTIPANEL) + #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" + #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen + #endif +#endif + +// @section extras + +// minimum time in microseconds that a movement needs to take if the buffer is emptied. +#define DEFAULT_MINSEGMENTTIME 20000 + +// If defined the movements slow down when the look ahead buffer is only half full +#define SLOWDOWN + +// Frequency limit +// See nophead's blog for more info +// Not working O +//#define XY_FREQUENCY_LIMIT 15 + +// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end +// of the buffer and all stops. This should not be much greater than zero and should only be changed +// if unwanted behavior is observed on a user's machine when running at very slow speeds. +#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s) + +// +// Backlash Compensation +// Adds extra movement to axes on direction-changes to account for backlash. +// +//#define BACKLASH_COMPENSATION +#if ENABLED(BACKLASH_COMPENSATION) + // Define values for backlash distance and correction. + // If BACKLASH_GCODE is enabled these values are the defaults. + #define BACKLASH_DISTANCE_MM { 0, 0, 0 } // (mm) + #define BACKLASH_CORRECTION 0.0 // 0.0 = no correction; 1.0 = full correction + + // Set BACKLASH_SMOOTHING_MM to spread backlash correction over multiple segments + // to reduce print artifacts. (Enabling this is costly in memory and computation!) + //#define BACKLASH_SMOOTHING_MM 3 // (mm) + + // Add runtime configuration and tuning of backlash values (M425) + //#define BACKLASH_GCODE + + #if ENABLED(BACKLASH_GCODE) + // Measure the Z backlash when probing (G29) and set with "M425 Z" + #define MEASURE_BACKLASH_WHEN_PROBING + + #if ENABLED(MEASURE_BACKLASH_WHEN_PROBING) + // When measuring, the probe will move up to BACKLASH_MEASUREMENT_LIMIT + // mm away from point of contact in BACKLASH_MEASUREMENT_RESOLUTION + // increments while checking for the contact to be broken. + #define BACKLASH_MEASUREMENT_LIMIT 0.5 // (mm) + #define BACKLASH_MEASUREMENT_RESOLUTION 0.005 // (mm) + #define BACKLASH_MEASUREMENT_FEEDRATE Z_PROBE_SPEED_SLOW // (mm/m) + #endif + #endif +#endif + +/** + * Automatic backlash, position and hotend offset calibration + * + * Enable G425 to run automatic calibration using an electrically- + * conductive cube, bolt, or washer mounted on the bed. + * + * G425 uses the probe to touch the top and sides of the calibration object + * on the bed and measures and/or correct positional offsets, axis backlash + * and hotend offsets. + * + * Note: HOTEND_OFFSET and CALIBRATION_OBJECT_CENTER must be set to within + * ±5mm of true values for G425 to succeed. + */ +//#define CALIBRATION_GCODE +#if ENABLED(CALIBRATION_GCODE) + + #define CALIBRATION_MEASUREMENT_RESOLUTION 0.01 // mm + + #define CALIBRATION_FEEDRATE_SLOW 60 // mm/m + #define CALIBRATION_FEEDRATE_FAST 1200 // mm/m + #define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/m + + // The following parameters refer to the conical section of the nozzle tip. + #define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm + #define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm + + // Uncomment to enable reporting (required for "G425 V", but consumes PROGMEM). + //#define CALIBRATION_REPORTING + + // The true location and dimension the cube/bolt/washer on the bed. + #define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0} // mm + #define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0} // mm + + // Comment out any sides which are unreachable by the probe. For best + // auto-calibration results, all sides must be reachable. + #define CALIBRATION_MEASURE_RIGHT + #define CALIBRATION_MEASURE_FRONT + #define CALIBRATION_MEASURE_LEFT + #define CALIBRATION_MEASURE_BACK + + // Probing at the exact top center only works if the center is flat. If + // probing on a screwhead or hollow washer, probe near the edges. + //#define CALIBRATION_MEASURE_AT_TOP_EDGES + + // Define pin which is read during calibration + #ifndef CALIBRATION_PIN + #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop + #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin + //#define CALIBRATION_PIN_PULLDOWN + #define CALIBRATION_PIN_PULLUP + #endif +#endif + +/** + * Adaptive Step Smoothing increases the resolution of multi-axis moves, particularly at step frequencies + * below 1kHz (for AVR) or 10kHz (for ARM), where aliasing between axes in multi-axis moves causes audible + * vibration and surface artifacts. The algorithm adapts to provide the best possible step smoothing at the + * lowest stepping frequencies. + */ +//#define ADAPTIVE_STEP_SMOOTHING + +/** + * Custom Microstepping + * Override as-needed for your setup. Up to 3 MS pins are supported. + */ +//#define MICROSTEP1 LOW,LOW,LOW +//#define MICROSTEP2 HIGH,LOW,LOW +//#define MICROSTEP4 LOW,HIGH,LOW +//#define MICROSTEP8 HIGH,HIGH,LOW +//#define MICROSTEP16 LOW,LOW,HIGH +//#define MICROSTEP32 HIGH,LOW,HIGH + +// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU. +#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16] + +/** + * @section stepper motor current + * + * Some boards have a means of setting the stepper motor current via firmware. + * + * The power on motor currents are set by: + * PWM_MOTOR_CURRENT - used by MINIRAMBO & ULTIMAIN_2 + * known compatible chips: A4982 + * DIGIPOT_MOTOR_CURRENT - used by BQ_ZUM_MEGA_3D, RAMBO & SCOOVO_X9H + * known compatible chips: AD5206 + * DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2 + * known compatible chips: MCP4728 + * DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, AZTEEG_X5_MINI_WIFI, MIGHTYBOARD_REVE + * known compatible chips: MCP4451, MCP4018 + * + * Motor currents can also be set by M907 - M910 and by the LCD. + * M907 - applies to all. + * M908 - BQ_ZUM_MEGA_3D, RAMBO, PRINTRBOARD_REVF, RIGIDBOARD_V2 & SCOOVO_X9H + * M909, M910 & LCD - only PRINTRBOARD_REVF & RIGIDBOARD_V2 + */ +//#define PWM_MOTOR_CURRENT { 1300, 1300, 1250 } // Values in milliamps +//#define DIGIPOT_MOTOR_CURRENT { 135,135,135,135,135 } // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A) +//#define DAC_MOTOR_CURRENT_DEFAULT { 70, 80, 90, 80 } // Default drive percent - X, Y, Z, E axis + +// Use an I2C based DIGIPOT (e.g., Azteeg X3 Pro) +//#define DIGIPOT_I2C +#if ENABLED(DIGIPOT_I2C) && !defined(DIGIPOT_I2C_ADDRESS_A) + /** + * Common slave addresses: + * + * A (A shifted) B (B shifted) IC + * Smoothie 0x2C (0x58) 0x2D (0x5A) MCP4451 + * AZTEEG_X3_PRO 0x2C (0x58) 0x2E (0x5C) MCP4451 + * AZTEEG_X5_MINI 0x2C (0x58) 0x2E (0x5C) MCP4451 + * AZTEEG_X5_MINI_WIFI 0x58 0x5C MCP4451 + * MIGHTYBOARD_REVE 0x2F (0x5E) MCP4018 + */ + #define DIGIPOT_I2C_ADDRESS_A 0x2C // unshifted slave address for first DIGIPOT + #define DIGIPOT_I2C_ADDRESS_B 0x2D // unshifted slave address for second DIGIPOT +#endif + +//#define DIGIPOT_MCP4018 // Requires library from https://github.com/stawel/SlowSoftI2CMaster +#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8 MKS SBASE: 5 +// Actual motor currents in Amps. The number of entries must match DIGIPOT_I2C_NUM_CHANNELS. +// These correspond to the physical drivers, so be mindful if the order is changed. +#define DIGIPOT_I2C_MOTOR_CURRENTS { 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0 } // AZTEEG_X3_PRO + +//=========================================================================== +//=============================Additional Features=========================== +//=========================================================================== + +// @section lcd + +// Change values more rapidly when the encoder is rotated faster +#define ENCODER_RATE_MULTIPLIER +#if ENABLED(ENCODER_RATE_MULTIPLIER) + #define ENCODER_10X_STEPS_PER_SEC 30 // (steps/s) Encoder rate for 10x speed + #define ENCODER_100X_STEPS_PER_SEC 80 // (steps/s) Encoder rate for 100x speed +#endif + +// Play a beep when the feedrate is changed from the Status Screen +//#define BEEP_ON_FEEDRATE_CHANGE +#if ENABLED(BEEP_ON_FEEDRATE_CHANGE) + #define FEEDRATE_CHANGE_BEEP_DURATION 10 + #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 +#endif + +// Include a page of printer information in the LCD Main Menu +#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif + +// Scroll a longer status message into view +#define STATUS_MESSAGE_SCROLLING + +// On the Info Screen, display XY with one decimal place when possible +//#define LCD_DECIMAL_SMALL_XY + +// The timeout (in ms) to return to the status screen from sub-menus +//#define LCD_TIMEOUT_TO_STATUS 15000 + +// Add an 'M73' G-code to set the current percentage +#define LCD_SET_PROGRESS_MANUALLY + +#if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS + //#define LCD_PROGRESS_BAR // Show a progress bar on HD44780 LCDs for SD printing + #if ENABLED(LCD_PROGRESS_BAR) + #define PROGRESS_BAR_BAR_TIME 2000 // (ms) Amount of time to show the bar + #define PROGRESS_BAR_MSG_TIME 3000 // (ms) Amount of time to show the status message + #define PROGRESS_MSG_EXPIRE 0 // (ms) Amount of time to retain the status message (0=forever) + //#define PROGRESS_MSG_ONCE // Show the message for MSG_TIME then clear it + //#define LCD_PROGRESS_BAR_TEST // Add a menu item to test the progress bar + #endif +#endif + +/** + * LED Control Menu + * Enable this feature to add LED Control to the LCD menu + */ +//#define LED_CONTROL_MENU +#if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif +#endif // LED_CONTROL_MENU + +#if ENABLED(SDSUPPORT) + + // Some RAMPS and other boards don't detect when an SD card is inserted. You can work + // around this by connecting a push button or single throw switch to the pin defined + // as SD_DETECT_PIN in your board's pins definitions. + // This setting should be disabled unless you are using a push button, pulling the pin to ground. + // Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER). + #define SD_DETECT_INVERTED + + #define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished + #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place. + + // Reverse SD sort to show "more recent" files first, according to the card's FAT. + // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended. + #define SDCARD_RATHERRECENTFIRST + + #define SD_MENU_CONFIRM_START // Confirm the selected SD file before printing + + //#define MENU_ADDAUTOSTART // Add a menu option to run auto#.g files + + #define EVENT_GCODE_SD_STOP "G28XY" // G-code to run on Stop Print (e.g., "G28XY" or "G27") + + /** + * Continue after Power-Loss (Creality3D) + * + * Store the current state to the SD Card at the start of each layer + * during SD printing. If the recovery file is found at boot time, present + * an option on the LCD screen to continue the print from the last-known + * point in the file. + */ + //#define POWER_LOSS_RECOVERY + #if ENABLED(POWER_LOSS_RECOVERY) + //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume + //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. + + // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, + // especially with "vase mode" printing. Set too high and vases cannot be continued. + #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + #endif + + /** + * Sort SD file listings in alphabetical order. + * + * With this option enabled, items on SD cards will be sorted + * by name for easier navigation. + * + * By default... + * + * - Use the slowest -but safest- method for sorting. + * - Folders are sorted to the top. + * - The sort key is statically allocated. + * - No added G-code (M34) support. + * - 40 item sorting limit. (Items after the first 40 are unsorted.) + * + * SD sorting uses static allocation (as set by SDSORT_LIMIT), allowing the + * compiler to calculate the worst-case usage and throw an error if the SRAM + * limit is exceeded. + * + * - SDSORT_USES_RAM provides faster sorting via a static directory buffer. + * - SDSORT_USES_STACK does the same, but uses a local stack-based buffer. + * - SDSORT_CACHE_NAMES will retain the sorted file listing in RAM. (Expensive!) + * - SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible. (Use with caution!) + */ + //#define SDCARD_SORT_ALPHA + + // SD Card Sorting options + #if ENABLED(SDCARD_SORT_ALPHA) + #define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). Costs 27 bytes each. + #define FOLDER_SORTING -1 // -1=above 0=none 1=below + #define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 g-code. + #define SDSORT_USES_RAM false // Pre-allocate a static array for faster pre-sorting. + #define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.) + #define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option. + #define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use! + #define SDSORT_CACHE_VFATS 2 // Maximum number of 13-byte VFAT entries to use for sorting. + // Note: Only affects SCROLL_LONG_FILENAMES with SDSORT_CACHE_NAMES but not SDSORT_DYNAMIC_RAM. + #endif + + // This allows hosts to request long names for files and folders with M33 + //#define LONG_FILENAME_HOST_SUPPORT + + // Enable this option to scroll long filenames in the SD card menu + #define SCROLL_LONG_FILENAMES + + // Leave the heaters on after Stop Print (not recommended!) + //#define SD_ABORT_NO_COOLDOWN + + /** + * This option allows you to abort SD printing when any endstop is triggered. + * This feature must be enabled with "M540 S1" or from the LCD menu. + * To have any effect, endstops must be enabled during SD printing. + */ + //#define SD_ABORT_ON_ENDSTOP_HIT + + /** + * This option makes it easier to print the same SD Card file again. + * On print completion the LCD Menu will open with the file selected. + * You can just click to start the print, or navigate elsewhere. + */ + //#define SD_REPRINT_LAST_SELECTED_FILE + + /** + * Auto-report SdCard status with M27 S + */ + //#define AUTO_REPORT_SD_STATUS + + /** + * Support for USB thumb drives using an Arduino USB Host Shield or + * equivalent MAX3421E breakout board. The USB thumb drive will appear + * to Marlin as an SD card. + * + * The MAX3421E must be assigned the same pins as the SD card reader, with + * the following pin mapping: + * + * SCLK, MOSI, MISO --> SCLK, MOSI, MISO + * INT --> SD_DETECT_PIN + * SS --> SDSS + */ + //#define USB_FLASH_DRIVE_SUPPORT + #if ENABLED(USB_FLASH_DRIVE_SUPPORT) + #define USB_CS_PIN SDSS + #define USB_INTR_PIN SD_DETECT_PIN + #endif + + /** + * When using a bootloader that supports SD-Firmware-Flashing, + * add a menu item to activate SD-FW-Update on the next reboot. + * + * Requires ATMEGA2560 (Arduino Mega) + * + * Tested with this bootloader: + * https://github.com/FleetProbe/MicroBridge-Arduino-ATMega2560 + */ + //#define SD_FIRMWARE_UPDATE + #if ENABLED(SD_FIRMWARE_UPDATE) + #define SD_FIRMWARE_UPDATE_EEPROM_ADDR 0x1FF + #define SD_FIRMWARE_UPDATE_ACTIVE_VALUE 0xF0 + #define SD_FIRMWARE_UPDATE_INACTIVE_VALUE 0xFF + #endif + + // Add an optimized binary file transfer mode, initiated with 'M28 B1' + //#define BINARY_FILE_TRANSFER + + #if HAS_SDCARD_CONNECTION + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD + #endif + +#endif // SDSUPPORT + +/** + * By default an onboard SD card reader may be shared as a USB mass- + * storage device. This option hides the SD card from the host PC. + */ +//#define NO_SD_HOST_DRIVE // Disable SD Card access over USB (for security). + +/** + * Additional options for Graphical Displays + * + * Use the optimizations here to improve printing performance, + * which can be adversely affected by graphical display drawing, + * especially when doing several short moves, and when printing + * on DELTA and SCARA machines. + * + * Some of these options may result in the display lagging behind + * controller events, as there is a trade-off between reliable + * printing performance versus fast display updates. + */ +#if HAS_GRAPHICAL_LCD + // Show SD percentage next to the progress bar + //#define DOGM_SD_PERCENT + + // Enable to save many cycles by drawing a hollow frame on the Info Screen + #define XYZ_HOLLOW_FRAME + + // Enable to save many cycles by drawing a hollow frame on Menu Screens + #define MENU_HOLLOW_FRAME + + // A bigger font is available for edit items. Costs 3120 bytes of PROGMEM. + // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. + #define USE_BIG_EDIT_FONT + + // A smaller font may be used on the Info Screen. Costs 2300 bytes of PROGMEM. + // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. + //#define USE_SMALL_INFOFONT + + // Enable this option and reduce the value to optimize screen updates. + // The normal delay is 10µs. Use the lowest value that still gives a reliable display. + //#define DOGM_SPI_DELAY_US 5 + + // Swap the CW/CCW indicators in the graphics overlay + //#define OVERLAY_GFX_REVERSE + + /** + * ST7920-based LCDs can emulate a 16 x 4 character display using + * the ST7920 character-generator for very fast screen updates. + * Enable LIGHTWEIGHT_UI to use this special display mode. + * + * Since LIGHTWEIGHT_UI has limited space, the position and status + * message occupy the same line. Set STATUS_EXPIRE_SECONDS to the + * length of time to display the status message before clearing. + * + * Set STATUS_EXPIRE_SECONDS to zero to never clear the status. + * This will prevent position updates from being displayed. + */ + #if ENABLED(U8GLIB_ST7920) + //#define LIGHTWEIGHT_UI + #if ENABLED(LIGHTWEIGHT_UI) + #define STATUS_EXPIRE_SECONDS 20 + #endif + #endif + + /** + * Status (Info) Screen customizations + * These options may affect code size and screen render time. + * Custom status screens can forcibly override these settings. + */ + //#define STATUS_COMBINE_HEATERS // Use combined heater images instead of separate ones + //#define STATUS_HOTEND_NUMBERLESS // Use plain hotend icons instead of numbered ones (with 2+ hotends) + #define STATUS_HOTEND_INVERTED // Show solid nozzle bitmaps when heating (Requires STATUS_HOTEND_ANIM) + #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating + #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating + #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap + //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap + //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames + //#define STATUS_HEAT_PERCENT // Show heating in a progress bar + //#define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash) + + // Frivolous Game Options + //#define MARLIN_BRICKOUT + //#define MARLIN_INVADERS + //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu + +#endif // HAS_GRAPHICAL_LCD + +// @section safety + +/** + * The watchdog hardware timer will do a reset and disable all outputs + * if the firmware gets too overloaded to read the temperature sensors. + * + * If you find that watchdog reboot causes your AVR board to hang forever, + * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO. + * NOTE: This method is less reliable as it can only catch hangups while + * interrupts are enabled. + */ +#define USE_WATCHDOG +#if ENABLED(USE_WATCHDOG) + //#define WATCHDOG_RESET_MANUAL +#endif + +// @section lcd + +/** + * Babystepping enables movement of the axes by tiny increments without changing + * the current position values. This feature is used primarily to adjust the Z + * axis in the first layer of a print in real-time. + * + * Warning: Does not respect endstops! + */ +#define BABYSTEPPING +#if ENABLED(BABYSTEPPING) + //#define BABYSTEP_WITHOUT_HOMING + //#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA! + #define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way + #define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion. + + #define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping. + #if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING) + #define DOUBLECLICK_MAX_INTERVAL 2500 // Maximum interval between clicks, in milliseconds. + // Note: Extra time may be added to mitigate controller latency. + #define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement). + //#define MOVE_Z_WHEN_IDLE // Jump to the move Z menu on doubleclick when printer is idle. + #if ENABLED(MOVE_Z_WHEN_IDLE) + #define MOVE_Z_IDLE_MULTIPLICATOR 1 // Multiply 1mm by this factor for the move step size. + #endif + #endif + + //#define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28 + + //#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping + #if ENABLED(BABYSTEP_ZPROBE_OFFSET) + //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets + //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor + #endif +#endif + +// @section extruder + +/** + * Linear Pressure Control v1.5 + * + * Assumption: advance [steps] = k * (delta velocity [steps/s]) + * K=0 means advance disabled. + * + * NOTE: K values for LIN_ADVANCE 1.5 differ from earlier versions! + * + * Set K around 0.22 for 3mm PLA Direct Drive with ~6.5cm between the drive gear and heatbreak. + * Larger K values will be needed for flexible filament and greater distances. + * If this algorithm produces a higher speed offset than the extruder can handle (compared to E jerk) + * print acceleration will be reduced during the affected moves to keep within the limit. + * + * See http://marlinfw.org/docs/features/lin_advance.html for full instructions. + * Mention @Sebastianv650 on GitHub to alert the author of any issues. + */ +//#define LIN_ADVANCE +#if ENABLED(LIN_ADVANCE) + //#define EXTRA_LIN_ADVANCE_K // Enable for second linear advance constants + #define LIN_ADVANCE_K 0.22 // Unit: mm compression per 1mm/s extruder speed + //#define LA_DEBUG // If enabled, this will generate debug information output over USB. +#endif + +// @section leveling + +#if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL) + // Override the mesh area if the automatic (max) area is too large + //#define MESH_MIN_X MESH_INSET + //#define MESH_MIN_Y MESH_INSET + //#define MESH_MAX_X X_BED_SIZE - (MESH_INSET) + //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET) +#endif + +/** + * Repeatedly attempt G29 leveling until it succeeds. + * Stop after G29_MAX_RETRIES attempts. + */ +//#define G29_RETRY_AND_RECOVER +#if ENABLED(G29_RETRY_AND_RECOVER) + #define G29_MAX_RETRIES 3 + #define G29_HALT_ON_FAILURE + /** + * Specify the GCODE commands that will be executed when leveling succeeds, + * between attempts, and after the maximum number of retries have been tried. + */ + #define G29_SUCCESS_COMMANDS "M117 Bed leveling done." + #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0" + #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1" + +#endif + +// @section extras + +// +// G2/G3 Arc Support +// +#define ARC_SUPPORT // Disable this feature to save ~3226 bytes +#if ENABLED(ARC_SUPPORT) + #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles + //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes +#endif + +// Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes. +//#define BEZIER_CURVE_SUPPORT + +/** + * G38 Probe Target + * + * This option adds G38.2 and G38.3 (probe towards target) + * and optionally G38.4 and G38.5 (probe away from target). + * Set MULTIPLE_PROBING for G38 to probe more than once. + */ +//#define G38_PROBE_TARGET +#if ENABLED(G38_PROBE_TARGET) + //#define G38_PROBE_AWAY // Include G38.4 and G38.5 to probe away from target + #define G38_MINIMUM_MOVE 0.0275 // (mm) Minimum distance that will produce a move. +#endif + +// Moves (or segments) with fewer steps than this will be joined with the next move +#define MIN_STEPS_PER_SEGMENT 6 + +/** + * Minimum delay after setting the stepper DIR (in ns) + * 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire) + * 20 : Minimum for TMC2xxx drivers + * 200 : Minimum for A4988 drivers + * 400 : Minimum for A5984 drivers + * 500 : Minimum for LV8729 drivers (guess, no info in datasheet) + * 650 : Minimum for DRV8825 drivers + * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet) + * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet) + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MINIMUM_STEPPER_DIR_DELAY 650 + +/** + * Minimum stepper driver pulse width (in µs) + * 0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers + * 0 : Minimum 500ns for LV8729, adjusted in stepper.h + * 1 : Minimum for A4988 and A5984 stepper drivers + * 2 : Minimum for DRV8825 stepper drivers + * 3 : Minimum for TB6600 stepper drivers + * 30 : Minimum for TB6560 stepper drivers + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MINIMUM_STEPPER_PULSE 2 + +/** + * Maximum stepping rate (in Hz) the stepper driver allows + * If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE) + * 500000 : Maximum for A4988 stepper driver + * 400000 : Maximum for TMC2xxx stepper drivers + * 250000 : Maximum for DRV8825 stepper driver + * 200000 : Maximum for LV8729 stepper driver + * 150000 : Maximum for TB6600 stepper driver + * 15000 : Maximum for TB6560 stepper driver + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MAXIMUM_STEPPER_RATE 250000 + +// @section temperature + +// Control heater 0 and heater 1 in parallel. +//#define HEATERS_PARALLEL + +//=========================================================================== +//================================= Buffers ================================= +//=========================================================================== + +// @section hidden + +// The number of linear motions that can be in the plan at any give time. +// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2 (e.g. 8, 16, 32) because shifts and ors are used to do the ring-buffering. +#if ENABLED(SDSUPPORT) + #define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller +#else + #define BLOCK_BUFFER_SIZE 16 // maximize block buffer +#endif + +// @section serial + +// The ASCII buffer for serial input +#define MAX_CMD_SIZE 96 +#define BUFSIZE 4 + +// Transmission to Host Buffer Size +// To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0. +// To buffer a simple "ok" you need 4 bytes. +// For ADVANCED_OK (M105) you need 32 bytes. +// For debug-echo: 128 bytes for the optimal speed. +// Other output doesn't need to be that speedy. +// :[0, 2, 4, 8, 16, 32, 64, 128, 256] +#define TX_BUFFER_SIZE 0 + +// Host Receive Buffer Size +// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough. +// To use flow control, set this buffer size to at least 1024 bytes. +// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048] +//#define RX_BUFFER_SIZE 1024 + +#if RX_BUFFER_SIZE >= 1024 + // Enable to have the controller send XON/XOFF control characters to + // the host to signal the RX buffer is becoming full. + //#define SERIAL_XON_XOFF +#endif + +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + +#if ENABLED(SDSUPPORT) + // Enable this option to collect and display the maximum + // RX queue usage after transferring a file to SD. + //#define SERIAL_STATS_MAX_RX_QUEUED + + // Enable this option to collect and display the number + // of dropped bytes after a file transfer to SD. + //#define SERIAL_STATS_DROPPED_RX +#endif + +// Enable an emergency-command parser to intercept certain commands as they +// enter the serial receive buffer, so they cannot be blocked. +// Currently handles M108, M112, M410 +// Does not work on boards using AT90USB (USBCON) processors! +//#define EMERGENCY_PARSER + +// Bad Serial-connections can miss a received command by sending an 'ok' +// Therefore some clients abort after 30 seconds in a timeout. +// Some other clients start sending commands while receiving a 'wait'. +// This "wait" is only sent when the buffer is empty. 1 second is a good value here. +//#define NO_TIMEOUTS 1000 // Milliseconds + +// Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary. +//#define ADVANCED_OK + +// Printrun may have trouble receiving long strings all at once. +// This option inserts short delays between lines of serial output. +#define SERIAL_OVERRUN_PROTECTION + +// @section extras + +/** + * Extra Fan Speed + * Adds a secondary fan speed for each print-cooling fan. + * 'M106 P T3-255' : Set a secondary speed for + * 'M106 P T2' : Use the set secondary speed + * 'M106 P T1' : Restore the previous fan speed + */ +//#define EXTRA_FAN_SPEED + +/** + * Firmware-based and LCD-controlled retract + * + * Add G10 / G11 commands for automatic firmware-based retract / recover. + * Use M207 and M208 to define parameters for retract / recover. + * + * Use M209 to enable or disable auto-retract. + * With auto-retract enabled, all G1 E moves within the set range + * will be converted to firmware-based retract/recover moves. + * + * Be sure to turn off auto-retract during filament change. + * + * Note that M207 / M208 / M209 settings are saved to EEPROM. + * + */ +//#define FWRETRACT +#if ENABLED(FWRETRACT) + #define FWRETRACT_AUTORETRACT // costs ~500 bytes of PROGMEM + #if ENABLED(FWRETRACT_AUTORETRACT) + #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over + #define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion + #endif + #define RETRACT_LENGTH 3 // Default retract length (positive mm) + #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change + #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) + #define RETRACT_ZRAISE 0 // Default retract Z-raise (mm) + #define RETRACT_RECOVER_LENGTH 0 // Default additional recover length (mm, added to retract length when recovering) + #define RETRACT_RECOVER_LENGTH_SWAP 0 // Default additional swap recover length (mm, added to retract length when recovering from extruder change) + #define RETRACT_RECOVER_FEEDRATE 8 // Default feedrate for recovering from retraction (mm/s) + #define RETRACT_RECOVER_FEEDRATE_SWAP 8 // Default feedrate for recovering from swap retraction (mm/s) + #if ENABLED(MIXING_EXTRUDER) + //#define RETRACT_SYNC_MIXING // Retract and restore all mixing steppers simultaneously + #endif +#endif + +/** + * Universal tool change settings. + * Applies to all types of extruders except where explicitly noted. + */ +#if EXTRUDERS > 1 + // Z raise distance for tool-change, as needed for some extruders + #define TOOLCHANGE_ZRAISE 2 // (mm) + //#define TOOLCHANGE_NO_RETURN // Never return to the previous position on tool-change + + // Retract and prime filament on tool-change + //#define TOOLCHANGE_FILAMENT_SWAP + #if ENABLED(TOOLCHANGE_FILAMENT_SWAP) + #define TOOLCHANGE_FIL_SWAP_LENGTH 12 // (mm) + #define TOOLCHANGE_FIL_EXTRA_PRIME 2 // (mm) + #define TOOLCHANGE_FIL_SWAP_RETRACT_SPEED 3600 // (mm/m) + #define TOOLCHANGE_FIL_SWAP_PRIME_SPEED 3600 // (mm/m) + #endif + + /** + * Position to park head during tool change. + * Doesn't apply to SWITCHING_TOOLHEAD, DUAL_X_CARRIAGE, or PARKING_EXTRUDER + */ + //#define TOOLCHANGE_PARK + #if ENABLED(TOOLCHANGE_PARK) + #define TOOLCHANGE_PARK_XY { X_MIN_POS + 10, Y_MIN_POS + 10 } + #define TOOLCHANGE_PARK_XY_FEEDRATE 6000 // (mm/m) + #endif +#endif + +/** + * Advanced Pause + * Experimental feature for filament change support and for parking the nozzle when paused. + * Adds the GCode M600 for initiating filament change. + * If PARK_HEAD_ON_PAUSE enabled, adds the GCode M125 to pause printing and park the nozzle. + * + * Requires an LCD display. + * Requires NOZZLE_PARK_FEATURE. + * This feature is required for the default FILAMENT_RUNOUT_SCRIPT. + */ +//#define ADVANCED_PAUSE_FEATURE +#if ENABLED(ADVANCED_PAUSE_FEATURE) + #define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate. + #define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract. + // This short retract is done immediately, before parking the nozzle. + #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast. + #define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. + #define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload. + // For Bowden, the full length of the tube and nozzle. + // For direct drive, the full length of the nozzle. + // Set to 0 for manual unloading. + #define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load. + #define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material. + // 0 to disable start loading and skip to fast load only + #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast. + #define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. + #define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle. + // For Bowden, the full length of the tube and nozzle. + // For direct drive, the full length of the nozzle. + //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted. + #define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate. + #define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading. + // Set to 0 for manual extrusion. + // Filament can be extruded repeatedly from the Filament Change menu + // until extrusion is consistent, and to purge old filament. + #define ADVANCED_PAUSE_RESUME_PRIME 0 // (mm) Extra distance to prime nozzle after returning from park. + //#define ADVANCED_PAUSE_FANS_PAUSE // Turn off print-cooling fans while the machine is paused. + + // Filament Unload does a Retract, Delay, and Purge first: + #define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length. + #define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract. + #define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged. + + #define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety. + #define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed. + #define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change. + + //#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change. + //#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change + + //#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu. + //#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302) +#endif + +// @section tmc + +/** + * TMC26X Stepper Driver options + * + * The TMC26XStepper library is required for this stepper driver. + * https://github.com/trinamic/TMC26XStepper + */ +#if HAS_DRIVER(TMC26X) + + #if AXIS_DRIVER_TYPE_X(TMC26X) + #define X_MAX_CURRENT 1000 // (mA) + #define X_SENSE_RESISTOR 91 // (mOhms) + #define X_MICROSTEPS 16 // Number of microsteps + #endif + + #if AXIS_DRIVER_TYPE_X2(TMC26X) + #define X2_MAX_CURRENT 1000 + #define X2_SENSE_RESISTOR 91 + #define X2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Y(TMC26X) + #define Y_MAX_CURRENT 1000 + #define Y_SENSE_RESISTOR 91 + #define Y_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Y2(TMC26X) + #define Y2_MAX_CURRENT 1000 + #define Y2_SENSE_RESISTOR 91 + #define Y2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z(TMC26X) + #define Z_MAX_CURRENT 1000 + #define Z_SENSE_RESISTOR 91 + #define Z_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z2(TMC26X) + #define Z2_MAX_CURRENT 1000 + #define Z2_SENSE_RESISTOR 91 + #define Z2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z3(TMC26X) + #define Z3_MAX_CURRENT 1000 + #define Z3_SENSE_RESISTOR 91 + #define Z3_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E0(TMC26X) + #define E0_MAX_CURRENT 1000 + #define E0_SENSE_RESISTOR 91 + #define E0_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E1(TMC26X) + #define E1_MAX_CURRENT 1000 + #define E1_SENSE_RESISTOR 91 + #define E1_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E2(TMC26X) + #define E2_MAX_CURRENT 1000 + #define E2_SENSE_RESISTOR 91 + #define E2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E3(TMC26X) + #define E3_MAX_CURRENT 1000 + #define E3_SENSE_RESISTOR 91 + #define E3_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E4(TMC26X) + #define E4_MAX_CURRENT 1000 + #define E4_SENSE_RESISTOR 91 + #define E4_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E5(TMC26X) + #define E5_MAX_CURRENT 1000 + #define E5_SENSE_RESISTOR 91 + #define E5_MICROSTEPS 16 + #endif + +#endif // TMC26X + +// @section tmc_smart + +/** + * To use TMC2130, TMC2160, TMC2660, TMC5130, TMC5160 stepper drivers in SPI mode + * connect your SPI pins to the hardware SPI interface on your board and define + * the required CS pins in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 + * pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.). + * You may also use software SPI if you wish to use general purpose IO pins. + * + * To use TMC2208 stepper UART-configurable stepper drivers connect #_SERIAL_TX_PIN + * to the driver side PDN_UART pin with a 1K resistor. + * To use the reading capabilities, also connect #_SERIAL_RX_PIN to PDN_UART without + * a resistor. + * The drivers can also be used with hardware serial. + * + * TMCStepper library is required to use TMC stepper drivers. + * https://github.com/teemuatlut/TMCStepper + */ +#if HAS_TRINAMIC + + #define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current + #define INTERPOLATE true // Interpolate X/Y/Z_MICROSTEPS to 256 + + #if AXIS_IS_TMC(X) + #define X_CURRENT 800 // (mA) RMS current. Multiply by 1.414 for peak current. + #define X_MICROSTEPS 16 // 0..256 + #define X_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(X2) + #define X2_CURRENT 800 + #define X2_MICROSTEPS 16 + #define X2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Y) + #define Y_CURRENT 800 + #define Y_MICROSTEPS 16 + #define Y_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Y2) + #define Y2_CURRENT 800 + #define Y2_MICROSTEPS 16 + #define Y2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Z) + #define Z_CURRENT 800 + #define Z_MICROSTEPS 16 + #define Z_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Z2) + #define Z2_CURRENT 800 + #define Z2_MICROSTEPS 16 + #define Z2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Z3) + #define Z3_CURRENT 800 + #define Z3_MICROSTEPS 16 + #define Z3_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E0) + #define E0_CURRENT 800 + #define E0_MICROSTEPS 16 + #define E0_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E1) + #define E1_CURRENT 800 + #define E1_MICROSTEPS 16 + #define E1_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E2) + #define E2_CURRENT 800 + #define E2_MICROSTEPS 16 + #define E2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E3) + #define E3_CURRENT 800 + #define E3_MICROSTEPS 16 + #define E3_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E4) + #define E4_CURRENT 800 + #define E4_MICROSTEPS 16 + #define E4_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E5) + #define E5_CURRENT 800 + #define E5_MICROSTEPS 16 + #define E5_RSENSE 0.11 + #endif + + /** + * Override default SPI pins for TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160 drivers here. + * The default pins can be found in your board's pins file. + */ + //#define X_CS_PIN -1 + //#define Y_CS_PIN -1 + //#define Z_CS_PIN -1 + //#define X2_CS_PIN -1 + //#define Y2_CS_PIN -1 + //#define Z2_CS_PIN -1 + //#define Z3_CS_PIN -1 + //#define E0_CS_PIN -1 + //#define E1_CS_PIN -1 + //#define E2_CS_PIN -1 + //#define E3_CS_PIN -1 + //#define E4_CS_PIN -1 + //#define E5_CS_PIN -1 + + /** + * Software option for SPI driven drivers (TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160). + * The default SW SPI pins are defined the respective pins files, + * but you can override or define them here. + */ + //#define TMC_USE_SW_SPI + //#define TMC_SW_MOSI -1 + //#define TMC_SW_MISO -1 + //#define TMC_SW_SCK -1 + + /** + * Four TMC2209 drivers can use the same HW/SW serial port with hardware configured addresses. + * Set the address using jumpers on pins MS1 and MS2. + * Address | MS1 | MS2 + * 0 | LOW | LOW + * 1 | HIGH | LOW + * 2 | LOW | HIGH + * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. + */ + #define X_SLAVE_ADDRESS 0 + #define Y_SLAVE_ADDRESS 0 + #define Z_SLAVE_ADDRESS 0 + #define X2_SLAVE_ADDRESS 0 + #define Y2_SLAVE_ADDRESS 0 + #define Z2_SLAVE_ADDRESS 0 + #define Z3_SLAVE_ADDRESS 0 + #define E0_SLAVE_ADDRESS 0 + #define E1_SLAVE_ADDRESS 0 + #define E2_SLAVE_ADDRESS 0 + #define E3_SLAVE_ADDRESS 0 + #define E4_SLAVE_ADDRESS 0 + #define E5_SLAVE_ADDRESS 0 + + /** + * Software enable + * + * Use for drivers that do not use a dedicated enable pin, but rather handle the same + * function through a communication line such as SPI or UART. + */ + //#define SOFTWARE_DRIVER_ENABLE + + /** + * TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only + * Use Trinamic's ultra quiet stepping mode. + * When disabled, Marlin will use spreadCycle stepping mode. + */ + #define STEALTHCHOP_XY + #define STEALTHCHOP_Z + #define STEALTHCHOP_E + + /** + * Optimize spreadCycle chopper parameters by using predefined parameter sets + * or with the help of an example included in the library. + * Provided parameter sets are + * CHOPPER_DEFAULT_12V + * CHOPPER_DEFAULT_19V + * CHOPPER_DEFAULT_24V + * CHOPPER_DEFAULT_36V + * CHOPPER_PRUSAMK3_24V // Imported parameters from the official Prusa firmware for MK3 (24V) + * CHOPPER_MARLIN_119 // Old defaults from Marlin v1.1.9 + * + * Define you own with + * { , , hysteresis_start[1..8] } + */ + #define CHOPPER_TIMING CHOPPER_DEFAULT_12V + + /** + * Monitor Trinamic drivers for error conditions, + * like overtemperature and short to ground. + * In the case of overtemperature Marlin can decrease the driver current until error condition clears. + * Other detected conditions can be used to stop the current print. + * Relevant g-codes: + * M906 - Set or get motor current in milliamps using axis codes X, Y, Z, E. Report values if no axis codes given. + * M911 - Report stepper driver overtemperature pre-warn condition. + * M912 - Clear stepper driver overtemperature pre-warn condition flag. + * M122 - Report driver parameters (Requires TMC_DEBUG) + */ + //#define MONITOR_DRIVER_STATUS + + #if ENABLED(MONITOR_DRIVER_STATUS) + #define CURRENT_STEP_DOWN 50 // [mA] + #define REPORT_CURRENT_CHANGE + #define STOP_ON_ERROR + #endif + + /** + * TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only + * The driver will switch to spreadCycle when stepper speed is over HYBRID_THRESHOLD. + * This mode allows for faster movements at the expense of higher noise levels. + * STEALTHCHOP_(XY|Z|E) must be enabled to use HYBRID_THRESHOLD. + * M913 X/Y/Z/E to live tune the setting + */ + //#define HYBRID_THRESHOLD + + #define X_HYBRID_THRESHOLD 100 // [mm/s] + #define X2_HYBRID_THRESHOLD 100 + #define Y_HYBRID_THRESHOLD 100 + #define Y2_HYBRID_THRESHOLD 100 + #define Z_HYBRID_THRESHOLD 3 + #define Z2_HYBRID_THRESHOLD 3 + #define Z3_HYBRID_THRESHOLD 3 + #define E0_HYBRID_THRESHOLD 30 + #define E1_HYBRID_THRESHOLD 30 + #define E2_HYBRID_THRESHOLD 30 + #define E3_HYBRID_THRESHOLD 30 + #define E4_HYBRID_THRESHOLD 30 + #define E5_HYBRID_THRESHOLD 30 + + /** + * TMC2130, TMC2160, TMC2209, TMC2660, TMC5130, and TMC5160 only + * Use StallGuard2 to sense an obstacle and trigger an endstop. + * Connect the stepper driver's DIAG1 pin to the X/Y endstop pin. + * X, Y, and Z homing will always be done in spreadCycle mode. + * + * X/Y/Z_STALL_SENSITIVITY is used for tuning the trigger sensitivity. + * Higher values make the system LESS sensitive. + * Lower value make the system MORE sensitive. + * Too low values can lead to false positives, while too high values will collide the axis without triggering. + * It is advised to set X/Y/Z_HOME_BUMP_MM to 0. + * M914 X/Y/Z to live tune the setting + */ + //#define SENSORLESS_HOMING // StallGuard capable drivers only + + /** + * Use StallGuard2 to probe the bed with the nozzle. + * + * CAUTION: This could cause damage to machines that use a lead screw or threaded rod + * to move the Z axis. Take extreme care when attempting to enable this feature. + */ + //#define SENSORLESS_PROBING // StallGuard capable drivers only + + #if EITHER(SENSORLESS_HOMING, SENSORLESS_PROBING) + // TMC2209: 0...255. TMC2130: -64...63 + #define X_STALL_SENSITIVITY 8 + #define Y_STALL_SENSITIVITY 8 + //#define Z_STALL_SENSITIVITY 8 + #endif + + /** + * Beta feature! + * Create a 50/50 square wave step pulse optimal for stepper drivers. + */ + //#define SQUARE_WAVE_STEPPING + + /** + * Enable M122 debugging command for TMC stepper drivers. + * M122 S0/1 will enable continous reporting. + */ + //#define TMC_DEBUG + + /** + * You can set your own advanced settings by filling in predefined functions. + * A list of available functions can be found on the library github page + * https://github.com/teemuatlut/TMCStepper + * + * Example: + * #define TMC_ADV() { \ + * stepperX.diag0_temp_prewarn(1); \ + * stepperY.interpolate(0); \ + * } + */ + #define TMC_ADV() { } + +#endif // HAS_TRINAMIC + +// @section L6470 + +/** + * L6470 Stepper Driver options + * + * Arduino-L6470 library (0.7.0 or higher) is required for this stepper driver. + * https://github.com/ameyer/Arduino-L6470 + * + * Requires the following to be defined in your pins_YOUR_BOARD file + * L6470_CHAIN_SCK_PIN + * L6470_CHAIN_MISO_PIN + * L6470_CHAIN_MOSI_PIN + * L6470_CHAIN_SS_PIN + * L6470_RESET_CHAIN_PIN (optional) + */ +#if HAS_DRIVER(L6470) + + //#define L6470_CHITCHAT // Display additional status info + + #if AXIS_DRIVER_TYPE_X(L6470) + #define X_MICROSTEPS 128 // Number of microsteps (VALID: 1, 2, 4, 8, 16, 32, 128) + #define X_OVERCURRENT 2000 // (mA) Current where the driver detects an over current (VALID: 375 x (1 - 16) - 6A max - rounds down) + #define X_STALLCURRENT 1500 // (mA) Current where the driver detects a stall (VALID: 31.25 * (1-128) - 4A max - rounds down) + #define X_MAX_VOLTAGE 127 // 0-255, Maximum effective voltage seen by stepper + #define X_CHAIN_POS 0 // Position in SPI chain, 0=Not in chain, 1=Nearest MOSI + #endif + + #if AXIS_DRIVER_TYPE_X2(L6470) + #define X2_MICROSTEPS 128 + #define X2_OVERCURRENT 2000 + #define X2_STALLCURRENT 1500 + #define X2_MAX_VOLTAGE 127 + #define X2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Y(L6470) + #define Y_MICROSTEPS 128 + #define Y_OVERCURRENT 2000 + #define Y_STALLCURRENT 1500 + #define Y_MAX_VOLTAGE 127 + #define Y_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Y2(L6470) + #define Y2_MICROSTEPS 128 + #define Y2_OVERCURRENT 2000 + #define Y2_STALLCURRENT 1500 + #define Y2_MAX_VOLTAGE 127 + #define Y2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Z(L6470) + #define Z_MICROSTEPS 128 + #define Z_OVERCURRENT 2000 + #define Z_STALLCURRENT 1500 + #define Z_MAX_VOLTAGE 127 + #define Z_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Z2(L6470) + #define Z2_MICROSTEPS 128 + #define Z2_OVERCURRENT 2000 + #define Z2_STALLCURRENT 1500 + #define Z2_MAX_VOLTAGE 127 + #define Z2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Z3(L6470) + #define Z3_MICROSTEPS 128 + #define Z3_OVERCURRENT 2000 + #define Z3_STALLCURRENT 1500 + #define Z3_MAX_VOLTAGE 127 + #define Z3_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E0(L6470) + #define E0_MICROSTEPS 128 + #define E0_OVERCURRENT 2000 + #define E0_STALLCURRENT 1500 + #define E0_MAX_VOLTAGE 127 + #define E0_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E1(L6470) + #define E1_MICROSTEPS 128 + #define E1_OVERCURRENT 2000 + #define E1_STALLCURRENT 1500 + #define E1_MAX_VOLTAGE 127 + #define E1_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E2(L6470) + #define E2_MICROSTEPS 128 + #define E2_OVERCURRENT 2000 + #define E2_STALLCURRENT 1500 + #define E2_MAX_VOLTAGE 127 + #define E2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E3(L6470) + #define E3_MICROSTEPS 128 + #define E3_OVERCURRENT 2000 + #define E3_STALLCURRENT 1500 + #define E3_MAX_VOLTAGE 127 + #define E3_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E4(L6470) + #define E4_MICROSTEPS 128 + #define E4_OVERCURRENT 2000 + #define E4_STALLCURRENT 1500 + #define E4_MAX_VOLTAGE 127 + #define E4_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E5(L6470) + #define E5_MICROSTEPS 128 + #define E5_OVERCURRENT 2000 + #define E5_STALLCURRENT 1500 + #define E5_MAX_VOLTAGE 127 + #define E5_CHAIN_POS 0 + #endif + + /** + * Monitor L6470 drivers for error conditions like over temperature and over current. + * In the case of over temperature Marlin can decrease the drive until the error condition clears. + * Other detected conditions can be used to stop the current print. + * Relevant g-codes: + * M906 - I1/2/3/4/5 Set or get motor drive level using axis codes X, Y, Z, E. Report values if no axis codes given. + * I not present or I0 or I1 - X, Y, Z or E0 + * I2 - X2, Y2, Z2 or E1 + * I3 - Z3 or E3 + * I4 - E4 + * I5 - E5 + * M916 - Increase drive level until get thermal warning + * M917 - Find minimum current thresholds + * M918 - Increase speed until max or error + * M122 S0/1 - Report driver parameters + */ + //#define MONITOR_L6470_DRIVER_STATUS + + #if ENABLED(MONITOR_L6470_DRIVER_STATUS) + #define KVAL_HOLD_STEP_DOWN 1 + //#define L6470_STOP_ON_ERROR + #endif + +#endif // L6470 + +/** + * TWI/I2C BUS + * + * This feature is an EXPERIMENTAL feature so it shall not be used on production + * machines. Enabling this will allow you to send and receive I2C data from slave + * devices on the bus. + * + * ; Example #1 + * ; This macro send the string "Marlin" to the slave device with address 0x63 (99) + * ; It uses multiple M260 commands with one B arg + * M260 A99 ; Target slave address + * M260 B77 ; M + * M260 B97 ; a + * M260 B114 ; r + * M260 B108 ; l + * M260 B105 ; i + * M260 B110 ; n + * M260 S1 ; Send the current buffer + * + * ; Example #2 + * ; Request 6 bytes from slave device with address 0x63 (99) + * M261 A99 B5 + * + * ; Example #3 + * ; Example serial output of a M261 request + * echo:i2c-reply: from:99 bytes:5 data:hello + */ + +// @section i2cbus + +//#define EXPERIMENTAL_I2CBUS +#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave + +// @section extras + +/** + * Photo G-code + * Add the M240 G-code to take a photo. + * The photo can be triggered by a digital pin or a physical movement. + */ +//#define PHOTO_GCODE +#if ENABLED(PHOTO_GCODE) + // A position to move to (and raise Z) before taking the photo + //#define PHOTO_POSITION { X_MAX_POS - 5, Y_MAX_POS, 0 } // { xpos, ypos, zraise } (M240 X Y Z) + //#define PHOTO_DELAY_MS 100 // (ms) Duration to pause before moving back (M240 P) + //#define PHOTO_RETRACT_MM 6.5 // (mm) E retract/recover for the photo move (M240 R S) + + // Canon RC-1 or homebrew digital camera trigger + // Data from: http://www.doc-diy.net/photo/rc-1_hacked/ + //#define PHOTOGRAPH_PIN 23 + + // Canon Hack Development Kit + // http://captain-slow.dk/2014/03/09/3d-printing-timelapses/ + //#define CHDK_PIN 4 + + // Optional second move with delay to trigger the camera shutter + //#define PHOTO_SWITCH_POSITION { X_MAX_POS, Y_MAX_POS } // { xpos, ypos } (M240 I J) + + // Duration to hold the switch or keep CHDK_PIN high + //#define PHOTO_SWITCH_MS 50 // (ms) (M240 D) +#endif + +/** + * Spindle & Laser control + * + * Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and + * to set spindle speed, spindle direction, and laser power. + * + * SuperPid is a router/spindle speed controller used in the CNC milling community. + * Marlin can be used to turn the spindle on and off. It can also be used to set + * the spindle speed from 5,000 to 30,000 RPM. + * + * You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V + * hardware PWM pin for the speed control and a pin for the rotation direction. + * + * See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details. + */ +//#define SPINDLE_FEATURE +//#define LASER_FEATURE +#if EITHER(SPINDLE_FEATURE, LASER_FEATURE) + #define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH + #define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power + #define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower + #define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power + #define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop + + #if ENABLED(SPINDLE_FEATURE) + //#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction + #define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction + #define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed + + /** + * The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power + * + * SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT + * where PWM duty cycle varies from 0 to 255 + * + * set the following for your controller (ALL MUST BE SET) + */ + #define SPEED_POWER_SLOPE 118.4 + #define SPEED_POWER_INTERCEPT 0 + #define SPEED_POWER_MIN 5000 + #define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM + #else + #define SPEED_POWER_SLOPE 0.3922 + #define SPEED_POWER_INTERCEPT 0 + #define SPEED_POWER_MIN 10 + #define SPEED_POWER_MAX 100 // 0-100% + #endif +#endif + +/** + * Coolant Control + * + * Add the M7, M8, and M9 commands to turn mist or flood coolant on and off. + * + * Note: COOLANT_MIST_PIN and/or COOLANT_FLOOD_PIN must also be defined. + */ +//#define COOLANT_CONTROL +#if ENABLED(COOLANT_CONTROL) + #define COOLANT_MIST // Enable if mist coolant is present + #define COOLANT_FLOOD // Enable if flood coolant is present + #define COOLANT_MIST_INVERT false // Set "true" if the on/off function is reversed + #define COOLANT_FLOOD_INVERT false // Set "true" if the on/off function is reversed +#endif + +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define FILWIDTH_ERROR_MARGIN 1.0 // (mm) If a measurement differs too much from nominal width ignore it + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + +/** + * CNC Coordinate Systems + * + * Enables G53 and G54-G59.3 commands to select coordinate systems + * and G92.1 to reset the workspace to native machine space. + */ +//#define CNC_COORDINATE_SYSTEMS + +/** + * Auto-report temperatures with M155 S + */ +#define AUTO_REPORT_TEMPERATURES + +/** + * Include capabilities in M115 output + */ +#define EXTENDED_CAPABILITIES_REPORT + +/** + * Disable all Volumetric extrusion options + */ +//#define NO_VOLUMETRICS + +#if DISABLED(NO_VOLUMETRICS) + /** + * Volumetric extrusion default state + * Activate to make volumetric extrusion the default method, + * with DEFAULT_NOMINAL_FILAMENT_DIA as the default diameter. + * + * M200 D0 to disable, M200 Dn to set a new diameter. + */ + //#define VOLUMETRIC_DEFAULT_ON +#endif + +/** + * Enable this option for a leaner build of Marlin that removes all + * workspace offsets, simplifying coordinate transformations, leveling, etc. + * + * - M206 and M428 are disabled. + * - G92 will revert to its behavior from Marlin 1.0. + */ +//#define NO_WORKSPACE_OFFSETS + +/** + * Set the number of proportional font spaces required to fill up a typical character space. + * This can help to better align the output of commands like `G29 O` Mesh Output. + * + * For clients that use a fixed-width font (like OctoPrint), leave this set to 1.0. + * Otherwise, adjust according to your client and font. + */ +#define PROPORTIONAL_FONT_RATIO 1.0 + +/** + * Spend 28 bytes of SRAM to optimize the GCode parser + */ +#define FASTER_GCODE_PARSER + +/** + * CNC G-code options + * Support CNC-style G-code dialects used by laser cutters, drawing machine cams, etc. + * Note that G0 feedrates should be used with care for 3D printing (if used at all). + * High feedrates may cause ringing and harm print quality. + */ +//#define PAREN_COMMENTS // Support for parentheses-delimited comments +//#define GCODE_MOTION_MODES // Remember the motion mode (G0 G1 G2 G3 G5 G38.X) and apply for X Y Z E F, etc. + +// Enable and set a (default) feedrate for all G0 moves +//#define G0_FEEDRATE 3000 // (mm/m) +#ifdef G0_FEEDRATE + //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode +#endif + +/** + * G-code Macros + * + * Add G-codes M810-M819 to define and run G-code macros. + * Macros are not saved to EEPROM. + */ +//#define GCODE_MACROS +#if ENABLED(GCODE_MACROS) + #define GCODE_MACROS_SLOTS 5 // Up to 10 may be used + #define GCODE_MACROS_SLOT_SIZE 50 // Maximum length of a single macro +#endif + +/** + * User-defined menu items that execute custom GCode + */ +//#define CUSTOM_USER_MENUS +#if ENABLED(CUSTOM_USER_MENUS) + //#define CUSTOM_USER_MENU_TITLE "Custom Commands" + #define USER_SCRIPT_DONE "M117 User Script Done" + #define USER_SCRIPT_AUDIBLE_FEEDBACK + //#define USER_SCRIPT_RETURN // Return to status screen after a script + + #define USER_DESC_1 "Home & UBL Info" + #define USER_GCODE_1 "G28\nG29 W" + + #define USER_DESC_2 "Preheat for " PREHEAT_1_LABEL + #define USER_GCODE_2 "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND) + + #define USER_DESC_3 "Preheat for " PREHEAT_2_LABEL + #define USER_GCODE_3 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND) + + #define USER_DESC_4 "Heat Bed/Home/Level" + #define USER_GCODE_4 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29" + + #define USER_DESC_5 "Home & Info" + #define USER_GCODE_5 "G28\nM503" +#endif + +/** + * Host Action Commands + * + * Define host streamer action commands in compliance with the standard. + * + * See https://reprap.org/wiki/G-code#Action_commands + * Common commands ........ poweroff, pause, paused, resume, resumed, cancel + * G29_RETRY_AND_RECOVER .. probe_rewipe, probe_failed + * + * Some features add reason codes to extend these commands. + * + * Host Prompt Support enables Marlin to use the host for user prompts so + * filament runout and other processes can be managed from the host side. + */ +//#define HOST_ACTION_COMMANDS +#if ENABLED(HOST_ACTION_COMMANDS) + //#define HOST_PROMPT_SUPPORT +#endif + +//=========================================================================== +//====================== I2C Position Encoder Settings ====================== +//=========================================================================== + +/** + * I2C position encoders for closed loop control. + * Developed by Chris Barr at Aus3D. + * + * Wiki: http://wiki.aus3d.com.au/Magnetic_Encoder + * Github: https://github.com/Aus3D/MagneticEncoder + * + * Supplier: http://aus3d.com.au/magnetic-encoder-module + * Alternative Supplier: http://reliabuild3d.com/ + * + * Reliabuild encoders have been modified to improve reliability. + */ + +//#define I2C_POSITION_ENCODERS +#if ENABLED(I2C_POSITION_ENCODERS) + + #define I2CPE_ENCODER_CNT 1 // The number of encoders installed; max of 5 + // encoders supported currently. + + #define I2CPE_ENC_1_ADDR I2CPE_PRESET_ADDR_X // I2C address of the encoder. 30-200. + #define I2CPE_ENC_1_AXIS X_AXIS // Axis the encoder module is installed on. _AXIS. + #define I2CPE_ENC_1_TYPE I2CPE_ENC_TYPE_LINEAR // Type of encoder: I2CPE_ENC_TYPE_LINEAR -or- + // I2CPE_ENC_TYPE_ROTARY. + #define I2CPE_ENC_1_TICKS_UNIT 2048 // 1024 for magnetic strips with 2mm poles; 2048 for + // 1mm poles. For linear encoders this is ticks / mm, + // for rotary encoders this is ticks / revolution. + //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper + // steps per full revolution (motor steps/rev * microstepping) + //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the + // printer will attempt to correct the error; errors + // smaller than this are ignored to minimize effects of + // measurement noise / latency (filter). + + #define I2CPE_ENC_2_ADDR I2CPE_PRESET_ADDR_Y // Same as above, but for encoder 2. + #define I2CPE_ENC_2_AXIS Y_AXIS + #define I2CPE_ENC_2_TYPE I2CPE_ENC_TYPE_LINEAR + #define I2CPE_ENC_2_TICKS_UNIT 2048 + //#define I2CPE_ENC_2_TICKS_REV (16 * 200) + //#define I2CPE_ENC_2_INVERT + #define I2CPE_ENC_2_EC_METHOD I2CPE_ECM_MICROSTEP + #define I2CPE_ENC_2_EC_THRESH 0.10 + + #define I2CPE_ENC_3_ADDR I2CPE_PRESET_ADDR_Z // Encoder 3. Add additional configuration options + #define I2CPE_ENC_3_AXIS Z_AXIS // as above, or use defaults below. + + #define I2CPE_ENC_4_ADDR I2CPE_PRESET_ADDR_E // Encoder 4. + #define I2CPE_ENC_4_AXIS E_AXIS + + #define I2CPE_ENC_5_ADDR 34 // Encoder 5. + #define I2CPE_ENC_5_AXIS E_AXIS + + // Default settings for encoders which are enabled, but without settings configured above. + #define I2CPE_DEF_TYPE I2CPE_ENC_TYPE_LINEAR + #define I2CPE_DEF_ENC_TICKS_UNIT 2048 + #define I2CPE_DEF_TICKS_REV (16 * 200) + #define I2CPE_DEF_EC_METHOD I2CPE_ECM_NONE + #define I2CPE_DEF_EC_THRESH 0.1 + + //#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given + // axis after which the printer will abort. Comment out to + // disable abort behavior. + + #define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault + // for this amount of time (in ms) before the encoder + // is trusted again. + + /** + * Position is checked every time a new command is executed from the buffer but during long moves, + * this setting determines the minimum update time between checks. A value of 100 works well with + * error rolling average when attempting to correct only for skips and not for vibration. + */ + #define I2CPE_MIN_UPD_TIME_MS 4 // (ms) Minimum time between encoder checks. + + // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise. + #define I2CPE_ERR_ROLLING_AVERAGE + +#endif // I2C_POSITION_ENCODERS + +/** + * MAX7219 Debug Matrix + * + * Add support for a low-cost 8x8 LED Matrix based on the Max7219 chip as a realtime status display. + * Requires 3 signal wires. Some useful debug options are included to demonstrate its usage. + */ +//#define MAX7219_DEBUG +#if ENABLED(MAX7219_DEBUG) + #define MAX7219_CLK_PIN 64 + #define MAX7219_DIN_PIN 57 + #define MAX7219_LOAD_PIN 44 + + //#define MAX7219_GCODE // Add the M7219 G-code to control the LED matrix + #define MAX7219_INIT_TEST 2 // Do a test pattern at initialization (Set to 2 for spiral) + #define MAX7219_NUMBER_UNITS 1 // Number of Max7219 units in chain. + #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) + // connector at: right=0 bottom=-90 top=90 left=180 + //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side + + /** + * Sample debug features + * If you add more debug displays, be careful to avoid conflicts! + */ + #define MAX7219_DEBUG_PRINTER_ALIVE // Blink corner LED of 8x8 matrix to show that the firmware is functioning + #define MAX7219_DEBUG_PLANNER_HEAD 3 // Show the planner queue head position on this and the next LED matrix row + #define MAX7219_DEBUG_PLANNER_TAIL 5 // Show the planner queue tail position on this and the next LED matrix row + + #define MAX7219_DEBUG_PLANNER_QUEUE 0 // Show the current planner queue depth on this and the next LED matrix row + // If you experience stuttering, reboots, etc. this option can reveal how + // tweaks made to the configuration are affecting the printer in real-time. +#endif + +/** + * NanoDLP Sync support + * + * Add support for Synchronized Z moves when using with NanoDLP. G0/G1 axis moves will output "Z_move_comp" + * string to enable synchronization with DLP projector exposure. This change will allow to use + * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands + */ +//#define NANODLP_Z_SYNC +#if ENABLED(NANODLP_Z_SYNC) + //#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move. + // Default behavior is limited to Z axis only. +#endif + +/** + * WiFi Support (Espressif ESP32 WiFi) + */ +//#define WIFISUPPORT +#if ENABLED(WIFISUPPORT) + #define WIFI_SSID "Wifi SSID" + #define WIFI_PWD "Wifi Password" + //#define WEBSUPPORT // Start a webserver with auto-discovery + //#define OTASUPPORT // Support over-the-air firmware updates +#endif + +/** + * Prusa Multi-Material Unit v2 + * Enable in Configuration.h + */ +#if ENABLED(PRUSA_MMU2) + + // Serial port used for communication with MMU2. + // For AVR enable the UART port used for the MMU. (e.g., internalSerial) + // For 32-bit boards check your HAL for available serial ports. (e.g., Serial2) + #define INTERNAL_SERIAL_PORT 2 + #define MMU2_SERIAL internalSerial + + // Use hardware reset for MMU if a pin is defined for it + //#define MMU2_RST_PIN 23 + + // Enable if the MMU2 has 12V stepper motors (MMU2 Firmware 1.0.2 and up) + //#define MMU2_MODE_12V + + // G-code to execute when MMU2 F.I.N.D.A. probe detects filament runout + #define MMU2_FILAMENT_RUNOUT_SCRIPT "M600" + + // Add an LCD menu for MMU2 + //#define MMU2_MENUS + #if ENABLED(MMU2_MENUS) + // Settings for filament load / unload from the LCD menu. + // This is for Prusa MK3-style extruders. Customize for your hardware. + #define MMU2_FILAMENTCHANGE_EJECT_FEED 80.0 + #define MMU2_LOAD_TO_NOZZLE_SEQUENCE \ + { 7.2, 562 }, \ + { 14.4, 871 }, \ + { 36.0, 1393 }, \ + { 14.4, 871 }, \ + { 50.0, 198 } + + #define MMU2_RAMMING_SEQUENCE \ + { 1.0, 1000 }, \ + { 1.0, 1500 }, \ + { 2.0, 2000 }, \ + { 1.5, 3000 }, \ + { 2.5, 4000 }, \ + { -15.0, 5000 }, \ + { -14.0, 1200 }, \ + { -6.0, 600 }, \ + { 10.0, 700 }, \ + { -10.0, 400 }, \ + { -50.0, 2000 } + + #endif + + //#define MMU2_DEBUG // Write debug info to serial output + +#endif // PRUSA_MMU2 + +/** + * Advanced Print Counter settings + */ +#if ENABLED(PRINTCOUNTER) + #define SERVICE_WARNING_BUZZES 3 + // Activate up to 3 service interval watchdogs + //#define SERVICE_NAME_1 "Service S" + //#define SERVICE_INTERVAL_1 100 // print hours + //#define SERVICE_NAME_2 "Service L" + //#define SERVICE_INTERVAL_2 200 // print hours + //#define SERVICE_NAME_3 "Service 3" + //#define SERVICE_INTERVAL_3 1 // print hours +#endif + +// @section develop + +/** + * M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins + */ +//#define PINS_DEBUGGING + +// Enable Marlin dev mode which adds some special commands +//#define MARLIN_DEV_MODE diff --git a/config/examples/adafruit/ST7565/Configuration.h b/config/examples/adafruit/ST7565/Configuration.h index bca7de92dd..42130ca486 100644 --- a/config/examples/adafruit/ST7565/Configuration.h +++ b/config/examples/adafruit/ST7565/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_RAMPS_14_EFB #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu //#define CUSTOM_MACHINE_NAME "3D Printer" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1523,8 +1529,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1681,6 +1690,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1908,31 +1925,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1966,15 +1964,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1987,6 +1976,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2012,17 +2043,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2118,8 +2156,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/delta/Anycubic/Kossel/Configuration.h b/config/examples/delta/Anycubic/Kossel/Configuration.h index 919f5ce234..cff624ee20 100644 --- a/config/examples/delta/Anycubic/Kossel/Configuration.h +++ b/config/examples/delta/Anycubic/Kossel/Configuration.h @@ -144,18 +144,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_TRIGORILLA_14 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "ANYCUBIC Kossel" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -292,7 +290,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -374,6 +379,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -410,7 +416,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -663,7 +669,7 @@ #if EITHER(DELTA_AUTO_CALIBRATION, DELTA_CALIBRATION_MENU) // Set the radius for the calibration probe points - max DELTA_PRINTABLE_RADIUS for non-eccentric probes - #define DELTA_CALIBRATION_RADIUS DELTA_PRINTABLE_RADIUS - MIN_PROBE_EDGE // (mm) + #define DELTA_CALIBRATION_RADIUS DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE) // (mm) // Set the steprate for papertest probing #define PROBE_MANUALLY_STEP 0.05 // (mm) #endif @@ -1383,10 +1389,10 @@ #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X // Set the boundaries for probing (where the probe can reach). - #define LEFT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE)) - #define RIGHT_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE) - #define FRONT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE)) - #define BACK_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE) + #define LEFT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE)) + #define RIGHT_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE) + #define FRONT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE)) + #define BACK_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE) // Probe along the Y axis, advancing X after each column //#define PROBE_Y_FIRST @@ -1711,8 +1717,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1869,6 +1878,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -2096,31 +2113,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -2154,15 +2152,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -2175,6 +2164,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2200,17 +2231,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2306,8 +2344,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h index 997f42aca1..23554eb6d4 100644 --- a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h +++ b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h @@ -651,6 +651,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE_XYZ 50*60 #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -853,6 +854,9 @@ // Include a page of printer information in the LCD Main Menu #define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -1039,7 +1043,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1137,6 +1141,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1366,6 +1371,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1751,6 +1759,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2436,6 +2447,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h index cf250bc3f3..bd69781f50 100644 --- a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h +++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_RAMPS_13_EFB #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "FLSUN Kossel" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -519,7 +525,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1651,8 +1657,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1809,6 +1818,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -2036,31 +2053,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -2094,15 +2092,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -2115,6 +2104,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2140,17 +2171,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2246,8 +2284,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h index 913c93c645..dd38a5a060 100644 --- a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h +++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h @@ -651,6 +651,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE_XYZ 50*60 #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -853,6 +854,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1039,7 +1043,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1137,6 +1141,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1366,6 +1371,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1751,6 +1759,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2436,6 +2447,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/delta/FLSUN/kossel/Configuration.h b/config/examples/delta/FLSUN/kossel/Configuration.h index e749f0def9..cff8e3cd34 100644 --- a/config/examples/delta/FLSUN/kossel/Configuration.h +++ b/config/examples/delta/FLSUN/kossel/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_RAMPS_13_EFB #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "FLSUN Kossel" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -519,7 +525,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1650,8 +1656,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1808,6 +1817,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -2035,31 +2052,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -2093,15 +2091,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -2114,6 +2103,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2139,17 +2170,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2245,8 +2283,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/delta/FLSUN/kossel/Configuration_adv.h b/config/examples/delta/FLSUN/kossel/Configuration_adv.h index 913c93c645..dd38a5a060 100644 --- a/config/examples/delta/FLSUN/kossel/Configuration_adv.h +++ b/config/examples/delta/FLSUN/kossel/Configuration_adv.h @@ -651,6 +651,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE_XYZ 50*60 #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -853,6 +854,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1039,7 +1043,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1137,6 +1141,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1366,6 +1371,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1751,6 +1759,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2436,6 +2447,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration.h b/config/examples/delta/FLSUN/kossel_mini/Configuration.h index e472a9889f..6455db835d 100644 --- a/config/examples/delta/FLSUN/kossel_mini/Configuration.h +++ b/config/examples/delta/FLSUN/kossel_mini/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_RAMPS_13_EFB #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Mini Kossel" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -519,7 +525,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1650,8 +1656,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1808,6 +1817,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -2035,31 +2052,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -2093,15 +2091,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -2114,6 +2103,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2139,17 +2170,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2245,8 +2283,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h index 3e24244473..798c141a6b 100644 --- a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h +++ b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h @@ -651,6 +651,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE_XYZ 50*60 #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -853,6 +854,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1039,7 +1043,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1137,6 +1141,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1366,6 +1371,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1751,6 +1759,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2436,6 +2447,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration.h b/config/examples/delta/Geeetech/Rostock 301/Configuration.h index 364264804a..f4557c3b7a 100644 --- a/config/examples/delta/Geeetech/Rostock 301/Configuration.h +++ b/config/examples/delta/Geeetech/Rostock 301/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_GTM32_PRO_VB #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Rostock 301" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1310,10 +1316,10 @@ #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X // Set the boundaries for probing (where the probe can reach). - //#define LEFT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE)) - //#define RIGHT_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE) - //#define FRONT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE)) - //#define BACK_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE) + //#define LEFT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE)) + //#define RIGHT_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE) + //#define FRONT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE)) + //#define BACK_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE) // Probe along the Y axis, advancing X after each column //#define PROBE_Y_FIRST @@ -1638,8 +1644,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1797,6 +1806,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -2024,31 +2041,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -2082,15 +2080,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -2103,6 +2092,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2128,17 +2159,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2234,8 +2272,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h index 554f4d68f3..5c29e4caad 100644 --- a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h +++ b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h @@ -651,6 +651,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE_XYZ 50*60 #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -853,6 +854,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1039,7 +1043,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1137,6 +1141,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1366,6 +1371,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1751,6 +1759,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2436,6 +2447,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/delta/Hatchbox_Alpha/Configuration.h b/config/examples/delta/Hatchbox_Alpha/Configuration.h index a93d2edb74..033c1068d2 100644 --- a/config/examples/delta/Hatchbox_Alpha/Configuration.h +++ b/config/examples/delta/Hatchbox_Alpha/Configuration.h @@ -134,18 +134,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_MKS_GEN_13 #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Hatchbox Alpha" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -282,7 +280,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -364,6 +369,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -400,7 +406,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -524,7 +530,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1325,10 +1331,10 @@ #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X // Set the boundaries for probing (where the probe can reach). - //#define LEFT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE)) - //#define RIGHT_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE) - //#define FRONT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE)) - //#define BACK_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE) + //#define LEFT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE)) + //#define RIGHT_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE) + //#define FRONT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE)) + //#define BACK_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE) // Probe along the Y axis, advancing X after each column //#define PROBE_Y_FIRST @@ -1653,8 +1659,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1811,6 +1820,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -2038,31 +2055,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -2096,15 +2094,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -2117,6 +2106,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2142,17 +2173,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2248,8 +2286,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/delta/MKS/SBASE/Configuration.h b/config/examples/delta/MKS/SBASE/Configuration.h index df2d9558a2..a6267eb1c8 100644 --- a/config/examples/delta/MKS/SBASE/Configuration.h +++ b/config/examples/delta/MKS/SBASE/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_MKS_SBASE #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Deltabot" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 -1 #define TEMP_SENSOR_1 0 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1310,10 +1316,10 @@ #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X // Set the boundaries for probing (where the probe can reach). - //#define LEFT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE)) - //#define RIGHT_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE) - //#define FRONT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE)) - //#define BACK_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE) + //#define LEFT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE)) + //#define RIGHT_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE) + //#define FRONT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE)) + //#define BACK_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE) // Probe along the Y axis, advancing X after each column //#define PROBE_Y_FIRST @@ -1638,8 +1644,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1796,6 +1805,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -2023,31 +2040,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -2081,15 +2079,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -2102,6 +2091,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2127,17 +2158,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2233,8 +2271,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/delta/MKS/SBASE/Configuration_adv.h b/config/examples/delta/MKS/SBASE/Configuration_adv.h index d7705ad057..b55c522802 100644 --- a/config/examples/delta/MKS/SBASE/Configuration_adv.h +++ b/config/examples/delta/MKS/SBASE/Configuration_adv.h @@ -651,6 +651,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE_XYZ 50*60 #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -853,6 +854,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1039,7 +1043,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1137,6 +1141,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1366,6 +1371,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1751,6 +1759,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2436,6 +2447,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/delta/Tevo Little Monster/Configuration.h b/config/examples/delta/Tevo Little Monster/Configuration.h index e134b4dc2f..edbb3d55c5 100644 --- a/config/examples/delta/Tevo Little Monster/Configuration.h +++ b/config/examples/delta/Tevo Little Monster/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_MKS_GEN_L #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "TEVO Little Monster" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -518,7 +524,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1314,10 +1320,10 @@ #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X // Set the boundaries for probing (where the probe can reach). - //#define LEFT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE)) - //#define RIGHT_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE) - //#define FRONT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE)) - //#define BACK_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE) + //#define LEFT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE)) + //#define RIGHT_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE) + //#define FRONT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE)) + //#define BACK_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE) // Probe along the Y axis, advancing X after each column //#define PROBE_Y_FIRST @@ -1642,8 +1648,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1800,6 +1809,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -2027,31 +2044,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -2085,15 +2083,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -2106,6 +2095,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2131,17 +2162,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2237,8 +2275,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/delta/Tevo Little Monster/Configuration_adv.h b/config/examples/delta/Tevo Little Monster/Configuration_adv.h index 847e4aa714..12b5a4b8a9 100644 --- a/config/examples/delta/Tevo Little Monster/Configuration_adv.h +++ b/config/examples/delta/Tevo Little Monster/Configuration_adv.h @@ -651,6 +651,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE_XYZ 50*60 #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -853,6 +854,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1039,7 +1043,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1137,6 +1141,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1366,6 +1371,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1751,6 +1759,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2436,6 +2447,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/delta/generic/Configuration.h b/config/examples/delta/generic/Configuration.h index f7eb796d08..cdafc5b728 100644 --- a/config/examples/delta/generic/Configuration.h +++ b/config/examples/delta/generic/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_RAMPS_14_EFB #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Deltabot" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 -1 #define TEMP_SENSOR_1 0 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1310,10 +1316,10 @@ #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X // Set the boundaries for probing (where the probe can reach). - //#define LEFT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE)) - //#define RIGHT_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE) - //#define FRONT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE)) - //#define BACK_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE) + //#define LEFT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE)) + //#define RIGHT_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE) + //#define FRONT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE)) + //#define BACK_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE) // Probe along the Y axis, advancing X after each column //#define PROBE_Y_FIRST @@ -1638,8 +1644,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1796,6 +1805,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -2023,31 +2040,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -2081,15 +2079,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -2102,6 +2091,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2127,17 +2158,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2233,8 +2271,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/delta/generic/Configuration_adv.h b/config/examples/delta/generic/Configuration_adv.h index 3e24244473..798c141a6b 100644 --- a/config/examples/delta/generic/Configuration_adv.h +++ b/config/examples/delta/generic/Configuration_adv.h @@ -651,6 +651,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE_XYZ 50*60 #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -853,6 +854,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1039,7 +1043,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1137,6 +1141,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1366,6 +1371,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1751,6 +1759,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2436,6 +2447,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/delta/kossel_mini/Configuration.h b/config/examples/delta/kossel_mini/Configuration.h index 103cfe52f1..8740481255 100644 --- a/config/examples/delta/kossel_mini/Configuration.h +++ b/config/examples/delta/kossel_mini/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_RAMPS_14_EFB #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Mini Kossel" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 7 #define TEMP_SENSOR_1 0 @@ -514,7 +520,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1312,10 +1318,10 @@ #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X // Set the boundaries for probing (where the probe can reach). - //#define LEFT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE)) - //#define RIGHT_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE) - //#define FRONT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE)) - //#define BACK_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE) + //#define LEFT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE)) + //#define RIGHT_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE) + //#define FRONT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE)) + //#define BACK_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE) // Probe along the Y axis, advancing X after each column //#define PROBE_Y_FIRST @@ -1640,8 +1646,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1798,6 +1807,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -2025,31 +2042,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -2083,15 +2081,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -2104,6 +2093,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2129,17 +2160,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2235,8 +2273,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/delta/kossel_mini/Configuration_adv.h b/config/examples/delta/kossel_mini/Configuration_adv.h index 3e24244473..798c141a6b 100644 --- a/config/examples/delta/kossel_mini/Configuration_adv.h +++ b/config/examples/delta/kossel_mini/Configuration_adv.h @@ -651,6 +651,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE_XYZ 50*60 #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -853,6 +854,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1039,7 +1043,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1137,6 +1141,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1366,6 +1371,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1751,6 +1759,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2436,6 +2447,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/delta/kossel_pro/Configuration.h b/config/examples/delta/kossel_pro/Configuration.h index ad56cf4fd0..3a007e41cc 100644 --- a/config/examples/delta/kossel_pro/Configuration.h +++ b/config/examples/delta/kossel_pro/Configuration.h @@ -133,18 +133,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_BRAINWAVE_PRO #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Kossel Pro" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -281,7 +279,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -363,6 +368,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -399,7 +405,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -506,7 +512,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //Kossel Pro heated bed plate with borosilicate glass @@ -1313,10 +1319,10 @@ #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X // Set the boundaries for probing (where the probe can reach). - //#define LEFT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE)) - //#define RIGHT_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE) - //#define FRONT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE)) - //#define BACK_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE) + //#define LEFT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE)) + //#define RIGHT_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE) + //#define FRONT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE)) + //#define BACK_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE) // Probe along the Y axis, advancing X after each column //#define PROBE_Y_FIRST @@ -1641,8 +1647,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1799,6 +1808,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -2026,31 +2043,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -2084,15 +2082,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -2105,6 +2094,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2130,17 +2161,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2236,8 +2274,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/delta/kossel_xl/Configuration.h b/config/examples/delta/kossel_xl/Configuration.h index 16fc46fd4a..d1fa5f949b 100644 --- a/config/examples/delta/kossel_xl/Configuration.h +++ b/config/examples/delta/kossel_xl/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_RAMPS_14_EFB #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "Kossel k800XL" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -518,7 +524,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1313,10 +1319,10 @@ #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X // Set the boundaries for probing (where the probe can reach). - //#define LEFT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE)) - //#define RIGHT_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE) - //#define FRONT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE)) - //#define BACK_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS -(MIN_PROBE_EDGE) + //#define LEFT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE)) + //#define RIGHT_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE) + //#define FRONT_PROBE_BED_POSITION -(DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE)) + //#define BACK_PROBE_BED_POSITION DELTA_PRINTABLE_RADIUS - (MIN_PROBE_EDGE) // Probe along the Y axis, advancing X after each column //#define PROBE_Y_FIRST @@ -1641,8 +1647,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1799,6 +1808,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -2026,31 +2043,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -2084,15 +2082,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -2105,6 +2094,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2130,17 +2161,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2236,8 +2274,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/delta/kossel_xl/Configuration_adv.h b/config/examples/delta/kossel_xl/Configuration_adv.h index 614d1ea525..bff8c69c14 100644 --- a/config/examples/delta/kossel_xl/Configuration_adv.h +++ b/config/examples/delta/kossel_xl/Configuration_adv.h @@ -651,6 +651,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE_XYZ 50*60 #define MANUAL_FEEDRATE { MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, MANUAL_FEEDRATE_XYZ, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -853,6 +854,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1039,7 +1043,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1137,6 +1141,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1366,6 +1371,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1751,6 +1759,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2436,6 +2447,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/gCreate/gMax1.5+/Configuration.h b/config/examples/gCreate/gMax1.5+/Configuration.h index f9870b6967..9874845e31 100644 --- a/config/examples/gCreate/gMax1.5+/Configuration.h +++ b/config/examples/gCreate/gMax1.5+/Configuration.h @@ -129,8 +129,7 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD //#define MOTHERBOARD BOARD_RAMPS_14_EEF #define MOTHERBOARD BOARD_RAMPS_14_EFB // gMax users please note: This is a Roxy modification. I print on glass and @@ -140,12 +139,11 @@ // temp. #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "gMax" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -282,7 +280,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -364,6 +369,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -400,7 +406,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -527,7 +533,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1537,8 +1543,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1695,6 +1704,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1922,31 +1939,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1980,15 +1978,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -2001,6 +1990,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2026,17 +2057,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2132,8 +2170,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/gCreate/gMax1.5+/Configuration_adv.h b/config/examples/gCreate/gMax1.5+/Configuration_adv.h index 97422d1e12..d566c06d98 100644 --- a/config/examples/gCreate/gMax1.5+/Configuration_adv.h +++ b/config/examples/gCreate/gMax1.5+/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/makibox/Configuration.h b/config/examples/makibox/Configuration.h index 09a9cc3aee..8872c1d33a 100644 --- a/config/examples/makibox/Configuration.h +++ b/config/examples/makibox/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_5DPRINT #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu #define CUSTOM_MACHINE_NAME "MakiBox" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -517,7 +523,7 @@ // drawing too much current from the power supply. #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1526,8 +1532,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1684,6 +1693,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1911,31 +1928,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1969,15 +1967,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1990,6 +1979,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2015,17 +2046,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2121,8 +2159,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/makibox/Configuration_adv.h b/config/examples/makibox/Configuration_adv.h index e2c9d81bce..e99c171472 100644 --- a/config/examples/makibox/Configuration_adv.h +++ b/config/examples/makibox/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/tvrrug/Round2/Configuration.h b/config/examples/tvrrug/Round2/Configuration.h index c19a991365..06a8cf5f80 100644 --- a/config/examples/tvrrug/Round2/Configuration.h +++ b/config/examples/tvrrug/Round2/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_OMCA #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu //#define CUSTOM_MACHINE_NAME "3D Printer" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "00000000-0000-0000-0000-000000000000" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -503,7 +509,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1518,8 +1524,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1676,6 +1685,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1903,31 +1920,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1961,15 +1959,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1982,6 +1971,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2007,17 +2038,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2113,8 +2151,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/tvrrug/Round2/Configuration_adv.h b/config/examples/tvrrug/Round2/Configuration_adv.h index 398f5f2831..576f93b8bc 100644 --- a/config/examples/tvrrug/Round2/Configuration_adv.h +++ b/config/examples/tvrrug/Round2/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -851,6 +852,9 @@ // Include a page of printer information in the LCD Main Menu //#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1037,7 +1041,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1135,6 +1139,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1364,6 +1369,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1749,6 +1757,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2434,6 +2445,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features diff --git a/config/examples/wt150/Configuration.h b/config/examples/wt150/Configuration.h index a144fe7a9b..b4913e369f 100644 --- a/config/examples/wt150/Configuration.h +++ b/config/examples/wt150/Configuration.h @@ -129,18 +129,16 @@ // Enable the Bluetooth serial interface on AT90USB devices //#define BLUETOOTH -// The following define selects which electronics board you have. -// Please choose the name from boards.h that matches your setup +// Choose the name from boards.h that matches your setup #ifndef MOTHERBOARD #define MOTHERBOARD BOARD_MIGHTYBOARD_REVE #endif -// Optional custom name for your RepStrap or other custom machine -// Displayed in the LCD "Ready" message +// Name displayed in the LCD "Ready" message and Info menu //#define CUSTOM_MACHINE_NAME "Weistek WT150" -// Define this to set a unique identifier for this printer, (Used by some programs to differentiate between machines) -// You can use an online service to generate a random UUID. (eg http://www.uuidgenerator.net/version4) +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 //#define MACHINE_UUID "5f0bb7a3-0e14-428c-812b-15ab0d3ecc71" // @section extruder @@ -277,7 +275,14 @@ #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis - #define SWITCHING_TOOLHEAD_X_SECURITY -35 // (mm) Security distance X axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching #endif @@ -359,6 +364,7 @@ * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) @@ -395,7 +401,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 -2 #define TEMP_SENSOR_1 0 @@ -519,7 +525,7 @@ #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current #if ENABLED(PIDTEMPBED) - + //#define MIN_BED_POWER 0 //#define PID_BED_DEBUG // Sends debug data to the serial port. //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) @@ -1528,8 +1534,11 @@ // Middle point of circle #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT - // Moves the nozzle to the initial position + // Move the nozzle to the initial position after cleaning #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + //#define NOZZLE_CLEAN_NO_Z #endif /** @@ -1686,6 +1695,14 @@ // //#define REVERSE_MENU_DIRECTION +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + // // Individual Axis Homing // @@ -1913,31 +1930,12 @@ // //#define LCD_FOR_MELZI -// -// SSD1306 OLED full graphics generic display -// -//#define U8GLIB_SSD1306 - -// -// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules -// -//#define SAV_3DGLCD -#if ENABLED(SAV_3DGLCD) - //#define U8GLIB_SSD1306 - #define U8GLIB_SH1106 -#endif - // // Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder // https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) // //#define ULTI_CONTROLLER -// -// TinyBoy2 128x64 OLED / Encoder Panel -// -//#define OLED_PANEL_TINYBOY2 - // // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 @@ -1971,15 +1969,6 @@ // //#define ANET_FULL_GRAPHICS_LCD -// -// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER -// http://reprap.org/wiki/MKS_12864OLED -// -// Tiny, but very sharp OLED display -// -//#define MKS_12864OLED // Uses the SH1106 controller (default) -//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller - // // AZSMZ 12864 LCD with SD // https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html @@ -1992,6 +1981,48 @@ // //#define SILVER_GATE_GLCD_CONTROLLER +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2017,17 +2048,24 @@ //============================================================================= // -// MKS Robin 320x240 color display +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) // -//#define MKS_ROBIN_TFT +//#define FSMC_GRAPHICAL_TFT //============================================================================= //============================ Other Controllers ============================ //============================================================================= // -// CONTROLLER TYPE: Keypad / Add-on +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 // +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif // // RepRapWorld REPRAPWORLD_KEYPAD v1.1 @@ -2123,8 +2161,10 @@ //#define NEOPIXEL_LED #if ENABLED(NEOPIXEL_LED) #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) - #define NEOPIXEL_PIN 4 // LED driving pin - #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup diff --git a/config/examples/wt150/Configuration_adv.h b/config/examples/wt150/Configuration_adv.h index 1364fd27d1..dd1cdda3e5 100644 --- a/config/examples/wt150/Configuration_adv.h +++ b/config/examples/wt150/Configuration_adv.h @@ -650,6 +650,7 @@ #if EITHER(ULTIPANEL, EXTENSIBLE_UI) #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) #if ENABLED(ULTIPANEL) #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen @@ -852,6 +853,9 @@ // Include a page of printer information in the LCD Main Menu #define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -1038,7 +1042,7 @@ // Add an optimized binary file transfer mode, initiated with 'M28 B1' //#define BINARY_FILE_TRANSFER - #ifdef TARGET_LPC1768 + #if HAS_SDCARD_CONNECTION /** * Set this option to one of the following (or the board's defaults apply): * @@ -1136,6 +1140,7 @@ //#define MARLIN_BRICKOUT //#define MARLIN_INVADERS //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu #endif // HAS_GRAPHICAL_LCD @@ -1365,6 +1370,9 @@ //#define SERIAL_XON_XOFF #endif +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + #if ENABLED(SDSUPPORT) // Enable this option to collect and display the maximum // RX queue usage after transferring a file to SD. @@ -1750,6 +1758,9 @@ * 1 | HIGH | LOW * 2 | LOW | HIGH * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. */ #define X_SLAVE_ADDRESS 0 #define Y_SLAVE_ADDRESS 0 @@ -2435,6 +2446,7 @@ #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) // connector at: right=0 bottom=-90 top=90 left=180 //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side /** * Sample debug features