diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index b4c9b46947..fde32ed554 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -524,7 +524,8 @@
   #define lerdgeFilSensor
 #endif
 
-#if EITHER(Creality422, Creality427) && DISABLED(MachineEnder3V2)
+#if (EITHER(Creality422, Creality427) && DISABLED(MachineEnder3V2)) || BOTH(OrigLCD, MachineEnder6)
+  #undef FORCE10SPRODISPLAY
   #define RET6_12864_LCD
 #endif
 
@@ -627,11 +628,11 @@
   #define LCD_SERIAL_PORT 1
   #define LCD_BAUDRATE 115200
   #define SERIAL_CATCHALL -1
-#elif ANY(MachineCR10SPro, MachineCRX, MachineEnder5Plus, MachineCR10Max) && NONE(GraphicLCD, MachineEnder3V2, Creality422, Creality427, MachineEnder6)
+#elif ANY(MachineCR10SPro, MachineCRX, MachineEnder5Plus, MachineCR10Max) && NONE(GraphicLCD, OrigLCD, MachineEnder3V2, Creality422, Creality427, MachineEnder6)
   #define LCD_SERIAL_PORT 2
   #define LCD_BAUDRATE 115200
   #define SERIAL_CATCHALL 0
-#elif ANY(MachineCR10SPro, MachineCRX, MachineEnder5Plus, MachineCR10Max, MachineEnder6) && DISABLED(GraphicLCD)
+#elif ANY(MachineCR10SPro, MachineCRX, MachineEnder5Plus, MachineCR10Max, MachineEnder6) && NONE(GraphicLCD, OrigLCD)
   #define LCD_SERIAL_PORT 3
   #define LCD_BAUDRATE 115200
   #define SERIAL_CATCHALL 1
@@ -1111,7 +1112,7 @@
 #endif
 
 #define TEMP_BED_RESIDENCY_TIME 5  // (seconds) Time to wait for bed to "settle" in M190
-#define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
+#define TEMP_BED_WINDOW          2  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
 /**
@@ -1862,7 +1863,7 @@
  * The probe replaces the Z-MIN endstop and is used for Z homing.
  * (Automatically enables USE_PROBE_FOR_Z_HOMING.)
  */
-#if NONE(Creality422, Creality427, MachineEnder6) && DISABLED(Creality42XUseZMin)
+#if NONE(Creality422, Creality427, MachineEnder6) && DISABLED(Creality42XUseZMin) || DISABLED(ABL_BLTOUCH)
   #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 #endif
 // Force the use of the probe for Z-axis homing
@@ -2134,7 +2135,7 @@
 #if ENABLED(PROBE_TARE)
   #define PROBE_TARE_TIME  200    // (ms) Time to hold tare pin
   #define PROBE_TARE_DELAY 200    // (ms) Delay after tare before
-  #define PROBE_TARE_STATE HIGH   // State to write pin for tare
+  #define PROBE_TARE_STATE LOW   // State to write pin for tare
   //#define PROBE_TARE_PIN PA5    // Override default pin
   #if ENABLED(PROBE_ACTIVATION_SWITCH)
     //#define PROBE_TARE_ONLY_WHILE_INACTIVE  // Fail to tare/probe if PROBE_ACTIVATION_SWITCH is active
@@ -2210,7 +2211,7 @@
  * readings with inductive probes and piezo sensors.
  */
 #if (ANY(ABL_EZABL, ABL_NCSW, MachineCR6, MachineCR6Max)) && DISABLED(MachineCR10Orig)
-  #define PROBING_HEATERS_OFF       // Turn heaters off when probing
+  //#define PROBING_HEATERS_OFF       // Turn heaters off when probing
 #endif
 #if ENABLED(PROBING_HEATERS_OFF)
   #define WAIT_FOR_BED_HEATER     // Wait for bed to heat back up between probes (to improve accuracy)
@@ -2842,7 +2843,7 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
   #define MESH_INSET 1
-  #if NONE(MachineCR10SPro, MachineCRX, MachineEnder5Plus, MachineCR10Max, MachineEnder4, OrigLCD) || ENABLED(GraphicLCD)
+  #if NONE(MachineCR10SPro, MachineCRX, MachineEnder5Plus, MachineCR10Max, MachineEnder4, OrigLCD) || ANY(GraphicLCD, OrigLCD)
     #define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
   #endif
 
@@ -2880,7 +2881,7 @@
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */
-#if NONE(ABL_EZABL, ABL_NCSW, ABL_BLTOUCH, ABL_TOUCH_MI, SKRMiniE3V2, MachineEnder3V2, FORCE10SPRODISPLAY, MachineCR6, MachineCR6Max) && (DISABLED(MachineCRX) || ENABLED(GraphicLCD))
+#if NONE(ABL_EZABL, ABL_NCSW, ABL_BLTOUCH, ABL_TOUCH_MI, SKRMiniE3V2, MachineEnder3V2, FORCE10SPRODISPLAY, MachineCR6, MachineCR6Max) && (DISABLED(MachineCRX) || ANY(GraphicLCD, OrigLCD))
   #define LCD_BED_LEVELING
 #endif
 
@@ -3883,7 +3884,7 @@
 // Third-party or vendor-customized controller interfaces.
 // Sources should be installed in 'src/lcd/extui'.
 //
-#if ANY(MachineCR10SPro, MachineCRX, MachineEnder5Plus, MachineCR10Max, MachineEnder6) && (NONE(GraphicLCD, SKRMiniE3V2) || ENABLED(FORCE10SPRODISPLAY))
+#if ANY(MachineCR10SPro, MachineCRX, MachineEnder5Plus, MachineCR10Max, MachineEnder6) && (NONE(GraphicLCD, SKRMiniE3V2, OrigLCD) || ENABLED(FORCE10SPRODISPLAY))
   #ifndef FORCE10SPRODISPLAY
     #define FORCE10SPRODISPLAY
   #endif
diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index 09e61755cf..5ac84ae966 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -1059,7 +1059,7 @@
 
   #if ENABLED(BACKLASH_GCODE)
     // Measure the Z backlash when probing (G29) and set with "M425 Z"
-    #define MEASURE_BACKLASH_WHEN_PROBING
+    //#define MEASURE_BACKLASH_WHEN_PROBING
 
     #if ENABLED(MEASURE_BACKLASH_WHEN_PROBING)
       // When measuring, the probe will move up to BACKLASH_MEASUREMENT_LIMIT