diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index 5ec41c596b..aa41f715c2 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -1,3 +1,48 @@
+ // If you have a trex 3, stock is this option plus 2208 on all axis. None in spreadcycle.
+#define TREX3
+
+// If you have a trex 3 that was upgraded from a 2+ with the kit, modifies home position and offsets.
+//#define TREX3_UPGRADE
+
+//Stock 2+ X is a 4988, all options off defaults to this
+//#define X_2208
+//#define X_Spreadcycle
+//#define X_S109
+
+// Y all options off defaults to 2+ 8825 / 3 2208
+//#define Y_2208 // Highly recommended as large prints with high mass can cause layer shifts with stealthchop at high speed
+//#define Y_Spreadcycle
+//#define Y_4988 // Some machines shipped with 4988 drivers across the board. Set this if you arent sure what you have and all the drivers look identical
+//#define Y_S109
+
+//Stock 2+ Z is a 8825, all options off defaults to this
+//#define Z_2208 // NOT Recommended! Dual stepper current draw is above the recommended limit for this driver
+//#define Z_4988 // Some machines shipped with 4988 drivers across the board. Set this if you arent sure what you have and all the drivers look identical
+//#define Z_Spreadcycle
+//#define Z_S109
+
+//Stock 2+ Z is a 4988, all options off defaults to this
+//#define E_2208 // Not Recommended! Stealthchop mode faults with linear advance
+//#define E_Spreadcycle
+//#define E_S109
+
+#define BedAC
+
+#define tallVersion
+
+//#define ABL_Bilinear
+/*
+ * Enables a filament sensor plugged into the laser pin. Disables the laser
+ */
+//#define FilamentSensor // Standard older TM3D runout sensor
+//#define lerdgeFilSensor // Newer inverted logic TM3D Runout Sensor
+//#define filamentEncoder
+
+//#define autoCalibrationKit
+
+
+//////////////////////////////////DO not edit below here unless you know what youre doing!  //////////////////////////////////
+
 /**
  * Marlin 3D Printer Firmware
  * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
@@ -21,6 +66,23 @@
  */
 #pragma once
 
+// The TREX2+ upgraded to the 3 enables most of the same options, simplify here
+#if ENABLED(TREX3_UPGRADE)
+  #define TREX3
+#endif
+
+#if ENABLED(TREX3)
+  #if DISABLED(X_S109)
+    #define X_2208
+  #endif
+  #if DISABLED(Y_S109)
+    #define Y_2208
+  #endif
+  #define Z_2208
+  #define E_2208
+  #define FilamentSensor
+#endif
+
 /**
  * Configuration.h
  *
@@ -70,8 +132,8 @@
 // @section info
 
 // Author info of this build printed to the host during boot and M115
-#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
-//#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
+#define STRING_CONFIG_H_AUTHOR "Tinymachines3D" // Who made the changes.
+#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
 
 /**
  * *** VENDORS PLEASE READ ***
@@ -88,10 +150,10 @@
 #define SHOW_BOOTSCREEN
 
 // Show the bitmap in Marlin/_Bootscreen.h on startup.
-//#define SHOW_CUSTOM_BOOTSCREEN
+#define SHOW_CUSTOM_BOOTSCREEN
 
 // Show the bitmap in Marlin/_Statusscreen.h on the status screen.
-//#define CUSTOM_STATUS_SCREEN_IMAGE
+#define CUSTOM_STATUS_SCREEN_IMAGE
 
 // @section machine
 
@@ -128,11 +190,22 @@
 
 // Choose the name from boards.h that matches your setup
 #ifndef MOTHERBOARD
-  #define MOTHERBOARD BOARD_RAMPS_14_EFB
+#if ENABLED(TREX3)
+  #define MOTHERBOARD BOARD_FORMBOT_TREX3
+#else
+  #define MOTHERBOARD BOARD_FORMBOT_TREX2PLUS
+#endif
 #endif
 
-// Name displayed in the LCD "Ready" message and Info menu
-//#define CUSTOM_MACHINE_NAME "3D Printer"
+// Optional custom name for your RepStrap or other custom machine
+// Displayed in the LCD "Ready" message
+#if ENABLED(TREX3_UPGRADE)
+  #define CUSTOM_MACHINE_TIME "T-REX 3(u)"
+#elif ENABLED(TREX3)
+  #define CUSTOM_MACHINE_NAME "T-REX 3"
+#else
+  #define CUSTOM_MACHINE_NAME "T-REX 2+"
+#endif
 
 // Printer's unique ID, used by some programs to differentiate between machines.
 // Choose your own or use a service like https://www.uuidgenerator.net/version4
@@ -142,7 +215,7 @@
 
 // This defines the number of extruders
 // :[0, 1, 2, 3, 4, 5, 6, 7, 8]
-#define EXTRUDERS 1
+#define EXTRUDERS 2
 
 // Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
 #define DEFAULT_NOMINAL_FILAMENT_DIA 1.75
@@ -314,7 +387,12 @@
 // Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
 // The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
 // For the other hotends it is their distance from the extruder 0 hotend.
-//#define HOTEND_OFFSET_X { 0.0, 20.00 } // (mm) relative X-offset for each nozzle
+  #if ENABLED(TREX3)
+    #define HOTEND_OFFSET_X {0.0, 438.5} // (mm) relative X-offset for each nozzle
+  #else
+    #define HOTEND_OFFSET_X {0.0, 442.0} // (mm) relative X-offset for each nozzle
+  #endif
+
 //#define HOTEND_OFFSET_Y { 0.0, 5.00 }  // (mm) relative Y-offset for each nozzle
 //#define HOTEND_OFFSET_Z { 0.0, 0.00 }  // (mm) relative Z-offset for each nozzle
 
@@ -419,15 +497,24 @@
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  */
-#define TEMP_SENSOR_0 1
-#define TEMP_SENSOR_1 0
+#if ENABLED(TREX3)
+  #define TEMP_SENSOR_0 61
+  #define TEMP_SENSOR_1 61
+#else
+  #define TEMP_SENSOR_0 1
+  #define TEMP_SENSOR_1 1
+#endif
 #define TEMP_SENSOR_2 0
 #define TEMP_SENSOR_3 0
 #define TEMP_SENSOR_4 0
 #define TEMP_SENSOR_5 0
 #define TEMP_SENSOR_6 0
 #define TEMP_SENSOR_7 0
-#define TEMP_SENSOR_BED 0
+#if(ENABLED(BedAC))
+  #define TEMP_SENSOR_BED 11
+#else
+  #define TEMP_SENSOR_BED 0
+#endif
 #define TEMP_SENSOR_PROBE 0
 #define TEMP_SENSOR_CHAMBER 0
 
@@ -446,11 +533,11 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-#define TEMP_RESIDENCY_TIME     10  // (seconds) Time to wait for hotend to "settle" in M109
+#define TEMP_RESIDENCY_TIME      3  // (seconds) Time to wait for hotend to "settle" in M109
 #define TEMP_WINDOW              1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_HYSTERESIS          3  // (°C) Temperature proximity considered "close enough" to the target
 
-#define TEMP_BED_RESIDENCY_TIME 10  // (seconds) Time to wait for bed to "settle" in M190
+#define TEMP_BED_RESIDENCY_TIME  5  // (seconds) Time to wait for bed to "settle" in M190
 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
@@ -469,8 +556,13 @@
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 // (Use MINTEMP for thermistor short/failure protection.)
-#define HEATER_0_MAXTEMP 275
-#define HEATER_1_MAXTEMP 275
+#if ENABLED(TREX3)
+  #define HEATER_0_MAXTEMP 350
+  #define HEATER_1_MAXTEMP 350
+#else
+  #define HEATER_0_MAXTEMP 410
+  #define HEATER_1_MAXTEMP 295
+#endif
 #define HEATER_2_MAXTEMP 275
 #define HEATER_3_MAXTEMP 275
 #define HEATER_4_MAXTEMP 275
@@ -491,22 +583,38 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
-  //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
+  #define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  #define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
+  #define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
   #if ENABLED(PID_PARAMS_PER_HOTEND)
     // Specify between 1 and HOTENDS values per array.
     // If fewer than EXTRUDER values are provided, the last element will be repeated.
-    #define DEFAULT_Kp_LIST {  22.20,  22.20 }
-    #define DEFAULT_Ki_LIST {   1.08,   1.08 }
-    #define DEFAULT_Kd_LIST { 114.00, 114.00 }
+    #if ENABLED(TREX3)
+      #define DEFAULT_Kp_LIST {  14.64,  14.64 }
+      #define DEFAULT_Ki_LIST {   1.08,   1.08 }
+      #define DEFAULT_Kd_LIST { 53.36, 53.36 }
+    #else
+      #define DEFAULT_Kp_LIST {  22.20,  22.20 }
+      #define DEFAULT_Ki_LIST {   1.08,   1.08 }
+      #define DEFAULT_Kd_LIST { 114.00, 114.00 }
+    #endif
   #else
-    #define DEFAULT_Kp  22.20
-    #define DEFAULT_Ki   1.08
-    #define DEFAULT_Kd 114.00
+    #define DEFAULT_Kp 22.2
+    #define DEFAULT_Ki 1.08
+    #define DEFAULT_Kd 114
   #endif
+  // MakerGear
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
+
+  // Mendel Parts V9 on 12V
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
+
 #endif // PIDTEMP
 
 //===========================================================================
@@ -625,10 +733,10 @@
 // Almost all printers will be using one per axis. Probes will use one or more of the
 // extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
 #define USE_XMIN_PLUG
-#define USE_YMIN_PLUG
+//#define USE_YMIN_PLUG
 #define USE_ZMIN_PLUG
-//#define USE_XMAX_PLUG
-//#define USE_YMAX_PLUG
+#define USE_XMAX_PLUG
+#define USE_YMAX_PLUG
 //#define USE_ZMAX_PLUG
 
 // Enable pullup for all endstops to prevent a floating state
@@ -658,13 +766,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -682,16 +790,38 @@
  *          TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE
  * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'L6474', 'POWERSTEP01', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
  */
-#define X_DRIVER_TYPE  A4988
-#define Y_DRIVER_TYPE  A4988
-#define Z_DRIVER_TYPE  A4988
-//#define X2_DRIVER_TYPE A4988
+#if ENABLED(X_2208)
+  #define X_DRIVER_TYPE  TMC2208_STANDALONE
+  #define X2_DRIVER_TYPE TMC2208_STANDALONE
+#else
+  #define X_DRIVER_TYPE  A4988
+  #define X2_DRIVER_TYPE A4988
+#endif
+#if ENABLED(Y_2208)
+  #define Y_DRIVER_TYPE  TMC2208_STANDALONE
+#elif ENABLED(Y_4988)
+  #define Y_DRIVER_TYPE  A4988
+#else
+  #define Y_DRIVER_TYPE  DRV8825
+#endif
+#if ENABLED(Z_2208)
+  #define Z_DRIVER_TYPE  TMC2208_STANDALONE
+#elif ENABLED(Z_4988)
+  #define Z_DRIVER_TYPE A4988
+#else
+  #define Z_DRIVER_TYPE  DRV8825
+#endif
 //#define Y2_DRIVER_TYPE A4988
 //#define Z2_DRIVER_TYPE A4988
 //#define Z3_DRIVER_TYPE A4988
 //#define Z4_DRIVER_TYPE A4988
-#define E0_DRIVER_TYPE A4988
-//#define E1_DRIVER_TYPE A4988
+#if ENABLED(E_2208)
+  #define E0_DRIVER_TYPE  TMC2208_STANDALONE
+  #define E1_DRIVER_TYPE TMC2208_STANDALONE
+#else
+  #define E0_DRIVER_TYPE DRV8825
+  #define E1_DRIVER_TYPE DRV8825
+#endif
 //#define E2_DRIVER_TYPE A4988
 //#define E3_DRIVER_TYPE A4988
 //#define E4_DRIVER_TYPE A4988
@@ -745,18 +875,37 @@
  * Override with M92
  *                                      X, Y, Z, E0 [, E1[, E2...]]
  */
-#define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 80, 4000, 500 }
+
+
+#if(ENABLED(Y_2208) || ENABLED(Y_4988) || ENABLED(Y_S109))
+  #define Y_STEPSMM 80
+#else
+  #define Y_STEPSMM 160
+#endif
+
+#if(ENABLED(Z_2208) || ENABLED(Z_4988))
+  #define Z_STEPSMM 800
+#else
+  #define Z_STEPSMM 1600
+#endif
+
+#define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, Y_STEPSMM, Z_STEPSMM, 93 }
 
 /**
  * Default Max Feed Rate (mm/s)
  * Override with M203
  *                                      X, Y, Z, E0 [, E1[, E2...]]
  */
-#define DEFAULT_MAX_FEEDRATE          { 300, 300, 5, 25 }
+#if ENABLED(Y_2208) && DISABLED(Y_Spreadcycle)
+  #define Y_MAXFEED 100
+#else
+  #define Y_MAXFEED 150
+#endif
+#define DEFAULT_MAX_FEEDRATE          { 200, Y_MAXFEED, 8, 75 }
 
-//#define LIMITED_MAX_FR_EDITING        // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
+#define LIMITED_MAX_FR_EDITING        // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
 #if ENABLED(LIMITED_MAX_FR_EDITING)
-  #define MAX_FEEDRATE_EDIT_VALUES    { 600, 600, 10, 50 } // ...or, set your own edit limits
+  #define MAX_FEEDRATE_EDIT_VALUES    { 300, 200, 15, 150 } // ...or, set your own edit limits
 #endif
 
 /**
@@ -765,11 +914,11 @@
  * Override with M201
  *                                      X, Y, Z, E0 [, E1[, E2...]]
  */
-#define DEFAULT_MAX_ACCELERATION      { 3000, 3000, 100, 10000 }
+#define DEFAULT_MAX_ACCELERATION      { 750, 500, 400, 3000 }
 
-//#define LIMITED_MAX_ACCEL_EDITING     // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
+#define LIMITED_MAX_ACCEL_EDITING     // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
 #if ENABLED(LIMITED_MAX_ACCEL_EDITING)
-  #define MAX_ACCEL_EDIT_VALUES       { 6000, 6000, 200, 20000 } // ...or, set your own edit limits
+  #define MAX_ACCEL_EDIT_VALUES       { 1500, 1500, 800, 5000 } // ...or, set your own edit limits
 #endif
 
 /**
@@ -780,9 +929,9 @@
  *   M204 R    Retract Acceleration
  *   M204 T    Travel Acceleration
  */
-#define DEFAULT_ACCELERATION          3000    // X, Y, Z and E acceleration for printing moves
-#define DEFAULT_RETRACT_ACCELERATION  3000    // E acceleration for retracts
-#define DEFAULT_TRAVEL_ACCELERATION   3000    // X, Y, Z acceleration for travel (non printing) moves
+#define DEFAULT_ACCELERATION          500    // X, Y, Z and E acceleration for printing moves
+#define DEFAULT_RETRACT_ACCELERATION  2000    // E acceleration for retracts
+#define DEFAULT_TRAVEL_ACCELERATION   500    // X, Y, Z acceleration for travel (non printing) moves
 
 /**
  * Default Jerk limits (mm/s)
@@ -792,10 +941,10 @@
  * When changing speed and direction, if the difference is less than the
  * value set here, it may happen instantaneously.
  */
-//#define CLASSIC_JERK
+#define CLASSIC_JERK
 #if ENABLED(CLASSIC_JERK)
   #define DEFAULT_XJERK 10.0
-  #define DEFAULT_YJERK 10.0
+  #define DEFAULT_YJERK 5.0
   #define DEFAULT_ZJERK  0.3
 
   //#define TRAVEL_EXTRA_XYJERK 0.0     // Additional jerk allowance for all travel moves
@@ -829,7 +978,7 @@
  *
  * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained
  */
-//#define S_CURVE_ACCELERATION
+#define S_CURVE_ACCELERATION
 
 //===========================================================================
 //============================= Z Probe Options =============================
@@ -903,7 +1052,7 @@
 /**
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
-//#define BLTOUCH
+#define BLTOUCH
 
 /**
  * Pressure sensor with a BLTouch-like interface
@@ -990,8 +1139,12 @@
  *     |    [-]    |
  *     O-- FRONT --+
  */
-#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
 
+#if ENABLED(TREX3)
+  #define NOZZLE_TO_PROBE_OFFSET { -3, 31, 0 }
+#else
+  #define NOZZLE_TO_PROBE_OFFSET { -7, 29, 0 }
+#endif
 // Most probes should stay away from the edges of the bed, but
 // with NOZZLE_AS_PROBE this can be negative for a wider probing area.
 #define PROBING_MARGIN 10
@@ -1014,7 +1167,7 @@
  * A total of 2 does fast/slow probes with a weighted average.
  * A total of 3 or more adds more slow probes, taking the average.
  */
-//#define MULTIPLE_PROBING 2
+#define MULTIPLE_PROBING 2
 //#define EXTRA_PROBING    1
 
 /**
@@ -1031,19 +1184,19 @@
  * Example: `M851 Z-5` with a CLEARANCE of 4  =>  9mm from bed to nozzle.
  *     But: `M851 Z+1` with a CLEARANCE of 2  =>  2mm from bed to nozzle.
  */
-#define Z_CLEARANCE_DEPLOY_PROBE   10 // Z Clearance for Deploy/Stow
+#define Z_CLEARANCE_DEPLOY_PROBE   5 // Z Clearance for Deploy/Stow
 #define Z_CLEARANCE_BETWEEN_PROBES  5 // Z Clearance between probe points
 #define Z_CLEARANCE_MULTI_PROBE     5 // Z Clearance between multiple probes
-//#define Z_AFTER_PROBING           5 // Z position after probing is done
+#define Z_AFTER_PROBING           5 // Z position after probing is done
 
-#define Z_PROBE_LOW_POINT          -2 // Farthest distance below the trigger-point to go before stopping
+#define Z_PROBE_LOW_POINT          -3 // Farthest distance below the trigger-point to go before stopping
 
 // For M851 give a range for adjusting the Z probe offset
-#define Z_PROBE_OFFSET_RANGE_MIN -20
-#define Z_PROBE_OFFSET_RANGE_MAX 20
+#define Z_PROBE_OFFSET_RANGE_MIN -9
+#define Z_PROBE_OFFSET_RANGE_MAX 9
 
 // Enable the M48 repeatability test to test probe accuracy
-//#define Z_MIN_PROBE_REPEATABILITY_TEST
+#define Z_MIN_PROBE_REPEATABILITY_TEST
 
 // Before deploy/stow pause for user confirmation
 //#define PAUSE_BEFORE_DEPLOY_STOW
@@ -1090,15 +1243,31 @@
 // @section machine
 
 // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
-#define INVERT_X_DIR false
-#define INVERT_Y_DIR true
-#define INVERT_Z_DIR false
-
+#if ENABLED(X_2208)
+  #define INVERT_X_DIR true
+#else
+  #define INVERT_X_DIR false
+#endif
+#if ENABLED(Y_2208)
+  #define INVERT_Y_DIR true
+#else
+  #define INVERT_Y_DIR false
+#endif
+#if ENABLED(Z_2208)
+  #define INVERT_Z_DIR false
+#else
+  #define INVERT_Z_DIR true
+#endif
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.
-#define INVERT_E0_DIR false
-#define INVERT_E1_DIR false
+#if ENABLED(E_2208) && DISABLED(TREX3)
+  #define INVERT_E0_DIR true
+  #define INVERT_E1_DIR false
+#else
+  #define INVERT_E0_DIR false
+  #define INVERT_E1_DIR true
+#endif
 #define INVERT_E2_DIR false
 #define INVERT_E3_DIR false
 #define INVERT_E4_DIR false
@@ -1120,22 +1289,34 @@
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1
-#define Y_HOME_DIR -1
+#define Y_HOME_DIR  1
 #define Z_HOME_DIR -1
 
 // @section machine
 
 // The size of the print bed
-#define X_BED_SIZE 200
-#define Y_BED_SIZE 200
+#define X_BED_SIZE 400
+#define Y_BED_SIZE 400
 
 // Travel limits (mm) after homing, corresponding to endstop positions.
-#define X_MIN_POS 0
-#define Y_MIN_POS 0
-#define Z_MIN_POS 0
-#define X_MAX_POS X_BED_SIZE
-#define Y_MAX_POS Y_BED_SIZE
-#define Z_MAX_POS 200
+#if DISABLED(TREX3) || ENABLED(TREX3_UPGRADE)
+    #define X_MIN_POS -42
+    #define Y_MIN_POS 0
+    #define Z_MIN_POS -3
+    #define X_MAX_POS 450
+    #define Y_MAX_POS Y_BED_SIZE
+#else
+    #define X_MIN_POS -47
+    #define Y_MIN_POS 0
+    #define Z_MIN_POS -3
+    #define X_MAX_POS 460
+    #define Y_MAX_POS Y_BED_SIZE
+#endif
+#if(ENABLED(tallVersion))
+  #define Z_MAX_POS 700
+#else
+  #define Z_MAX_POS 500
+#endif
 
 /**
  * Software Endstops
@@ -1163,7 +1344,7 @@
 #endif
 
 #if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS)
-  //#define SOFT_ENDSTOPS_MENU_ITEM  // Enable/Disable software endstops from the LCD
+  #define SOFT_ENDSTOPS_MENU_ITEM  // Enable/Disable software endstops from the LCD
 #endif
 
 /**
@@ -1173,13 +1354,23 @@
  * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
  * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
  */
-//#define FILAMENT_RUNOUT_SENSOR
+ #if ANY(FilamentSensor, filamentEncoder, lerdgeFilSensor)
+  #define FILAMENT_RUNOUT_SENSOR
+#endif
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
-  #define FIL_RUNOUT_ENABLED_DEFAULT true // Enable the sensor on startup. Override with M412 followed by M500.
-  #define NUM_RUNOUT_SENSORS   1          // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_STATE     LOW        // Pin state indicating that filament is NOT present.
-  #define FIL_RUNOUT_PULLUP               // Use internal pullup for filament runout pins.
-  //#define FIL_RUNOUT_PULLDOWN           // Use internal pulldown for filament runout pins.
+ #define FIL_RUNOUT_ENABLED_DEFAULT true // Enable the sensor on startup. Override with M412 followed by M500.
+ #if ENABLED(TREX3)
+  #define NUM_RUNOUT_SENSORS   2
+ #else
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
+ #endif
+ #if ENABLED(lerdgeFilSensor) || ENABLED(TREX3)
+   #define FIL_RUNOUT_STATE     LOW // set to true to invert the logic of the sensor.
+ #else
+   #define FIL_RUNOUT_STATE     HIGH // set to true to invert the logic of the sensor.
+ #endif
+  #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
+  //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 
   // Set one or more commands to execute on filament runout.
   // (After 'M412 H' Marlin will ask the host to handle the process.)
@@ -1188,13 +1379,19 @@
   // After a runout is detected, continue printing this length of filament
   // before executing the runout script. Useful for a sensor at the end of
   // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead.
-  //#define FILAMENT_RUNOUT_DISTANCE_MM 25
+  #if ENABLED(filamentEncoder)
+    #define FILAMENT_RUNOUT_DISTANCE_MM 15
+  #else
+    #define FILAMENT_RUNOUT_DISTANCE_MM 5
+  #endif
 
   #ifdef FILAMENT_RUNOUT_DISTANCE_MM
     // Enable this option to use an encoder disc that toggles the runout pin
     // as the filament moves. (Be sure to set FILAMENT_RUNOUT_DISTANCE_MM
     // large enough to avoid false positives.)
-    //#define FILAMENT_MOTION_SENSOR
+    #if ENABLED(filamentEncoder)
+      #define FILAMENT_MOTION_SENSOR
+    #endif
   #endif
 #endif
 
@@ -1238,15 +1435,18 @@
  */
 //#define AUTO_BED_LEVELING_3POINT
 //#define AUTO_BED_LEVELING_LINEAR
-//#define AUTO_BED_LEVELING_BILINEAR
-//#define AUTO_BED_LEVELING_UBL
+#if ENABLED(ABL_Bilinear)
+  #define AUTO_BED_LEVELING_BILINEAR
+#else
+  #define AUTO_BED_LEVELING_UBL
+#endif
 //#define MESH_BED_LEVELING
 
 /**
  * Normally G28 leaves leveling disabled on completion. Enable
  * this option to have G28 restore the prior leveling state.
  */
-//#define RESTORE_LEVELING_AFTER_G28
+#define RESTORE_LEVELING_AFTER_G28
 
 /**
  * Enable detailed logging of G28, G29, M48, etc.
@@ -1270,7 +1470,7 @@
   /**
    * Enable the G26 Mesh Validation Pattern tool.
    */
-  //#define G26_MESH_VALIDATION
+  #define G26_MESH_VALIDATION
   #if ENABLED(G26_MESH_VALIDATION)
     #define MESH_TEST_NOZZLE_SIZE    0.4  // (mm) Diameter of primary nozzle.
     #define MESH_TEST_LAYER_HEIGHT   0.2  // (mm) Default layer height for the G26 Mesh Validation Tool.
@@ -1285,7 +1485,7 @@
 #if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR)
 
   // Set the number of grid points per dimension.
-  #define GRID_MAX_POINTS_X 3
+  #define GRID_MAX_POINTS_X 11
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
 
   // Probe along the Y axis, advancing X after each column
@@ -1315,16 +1515,16 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
-  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+  #define MESH_EDIT_GFX_OVERLAY      // Display a graphics overlay while editing the mesh
 
-  #define MESH_INSET 1              // Set Mesh bounds as an inset region of the bed
-  #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
+  #define MESH_INSET 3              // Set Mesh bounds as an inset region of the bed
+  #define GRID_MAX_POINTS_X 15      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
 
   #define UBL_MESH_EDIT_MOVES_Z     // Sophisticated users prefer no movement of nozzle
   #define UBL_SAVE_ACTIVE_ON_M500   // Save the currently active mesh in the current slot on M500
 
-  //#define UBL_Z_RAISE_WHEN_OFF_MESH 2.5 // When the nozzle is off the mesh, this value is used
+  #define UBL_Z_RAISE_WHEN_OFF_MESH 0.0 // When the nozzle is off the mesh, this value is used
                                           // as the Z-Height correction value.
 
 #elif ENABLED(MESH_BED_LEVELING)
@@ -1354,7 +1554,7 @@
 #endif
 
 // Add a menu item to move between bed corners for manual bed adjustment
-//#define LEVEL_BED_CORNERS
+#define LEVEL_BED_CORNERS
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets
@@ -1378,7 +1578,7 @@
 // For DELTA this is the top-center of the Cartesian print volume.
 //#define MANUAL_X_HOME_POS 0
 //#define MANUAL_Y_HOME_POS 0
-//#define MANUAL_Z_HOME_POS 0
+#define MANUAL_Z_HOME_POS 0
 
 // Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area.
 //
@@ -1389,7 +1589,7 @@
 // - Move the Z probe (or nozzle) to a defined XY point before Z Homing.
 // - Prevent Z homing when the Z probe is outside bed area.
 //
-//#define Z_SAFE_HOMING
+#define Z_SAFE_HOMING
 
 #if ENABLED(Z_SAFE_HOMING)
   #define Z_SAFE_HOMING_X_POINT X_CENTER  // X point for Z homing
@@ -1398,7 +1598,7 @@
 
 // Homing speeds (mm/min)
 #define HOMING_FEEDRATE_XY (50*60)
-#define HOMING_FEEDRATE_Z  (4*60)
+#define HOMING_FEEDRATE_Z  (6*60)
 
 // Validate that endstops are triggered on homing moves
 #define VALIDATE_HOMING_ENDSTOPS
@@ -1475,12 +1675,12 @@
  *   M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
  *   M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
  */
-//#define EEPROM_SETTINGS     // Persistent storage with M500 and M501
+#define EEPROM_SETTINGS     // Persistent storage with M500 and M501
 //#define DISABLE_M503        // Saves ~2700 bytes of PROGMEM. Disable for release!
 #define EEPROM_CHITCHAT       // Give feedback on EEPROM commands. Disable to save PROGMEM.
 #define EEPROM_BOOT_SILENT    // Keep M503 quiet and only give errors during first load
 #if ENABLED(EEPROM_SETTINGS)
-  //#define EEPROM_AUTO_INIT  // Init EEPROM automatically on any errors.
+  #define EEPROM_AUTO_INIT  // Init EEPROM automatically on any errors.
 #endif
 
 //
@@ -1527,11 +1727,11 @@
  *    P1  Raise the nozzle always to Z-park height.
  *    P2  Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
  */
-//#define NOZZLE_PARK_FEATURE
+#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
   // Specify a park position as { X, Y, Z_raise }
-  #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
+  #define NOZZLE_PARK_POINT { 150, (Y_MIN_POS + 10), 10 }
   //#define NOZZLE_PARK_X_ONLY          // X move only is required to park
   //#define NOZZLE_PARK_Y_ONLY          // Y move only is required to park
   #define NOZZLE_PARK_Z_RAISE_MIN   2   // (mm) Always raise Z by at least this distance
@@ -1576,19 +1776,19 @@
  *   Caveats: The ending Z should be the same as starting Z.
  * Attention: EXPERIMENTAL. G-code arguments may change.
  */
-//#define NOZZLE_CLEAN_FEATURE
+#define NOZZLE_CLEAN_FEATURE
 
 #if ENABLED(NOZZLE_CLEAN_FEATURE)
   // Default number of pattern repetitions
-  #define NOZZLE_CLEAN_STROKES  12
+  #define NOZZLE_CLEAN_STROKES  4
 
   // Default number of triangles
   #define NOZZLE_CLEAN_TRIANGLES  3
 
   // Specify positions for each tool as { { X, Y, Z }, { X, Y, Z } }
   // Dual hotend system may use { {  -20, (Y_BED_SIZE / 2), (Z_MIN_POS + 1) },  {  420, (Y_BED_SIZE / 2), (Z_MIN_POS + 1) }}
-  #define NOZZLE_CLEAN_START_POINT { {  30, 30, (Z_MIN_POS + 1) } }
-  #define NOZZLE_CLEAN_END_POINT   { { 100, 60, (Z_MIN_POS + 1) } }
+  #define NOZZLE_CLEAN_START_POINT { {  -20, (Y_BED_SIZE / 2), (Z_MIN_POS + 1) },  {  420, (Y_BED_SIZE / 2), (Z_MIN_POS + 1) }}
+  #define NOZZLE_CLEAN_END_POINT   { {  (-30), (Y_BED_SIZE / 2), (Z_MIN_POS + 1) },  {  (430), (Y_BED_SIZE / 2), (Z_MIN_POS + 1) }}
 
   // Circular pattern radius
   #define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5
@@ -1728,7 +1928,7 @@
  * SD Card support is disabled by default. If your controller has an SD slot,
  * you must uncomment the following option or it won't work.
  */
-//#define SDSUPPORT
+#define SDSUPPORT
 
 /**
  * SD CARD: SPI SPEED
@@ -1808,7 +2008,7 @@
 //
 // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
 //
-//#define INDIVIDUAL_AXIS_HOMING_MENU
+#define INDIVIDUAL_AXIS_HOMING_MENU
 
 //
 // SPEAKER/BUZZER
@@ -1989,7 +2189,7 @@
 // RepRapDiscount FULL GRAPHIC Smart Controller
 // https://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
 //
-//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
+#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
 
 //
 // ReprapWorld Graphical LCD
@@ -2359,8 +2559,9 @@
 // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
 // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
 // is too low, you should also increment SOFT_PWM_SCALE.
-//#define FAN_SOFT_PWM
-
+#if ENABLED(TREX3)
+  #define FAN_SOFT_PWM
+#endif
 // Incrementing this by 1 will double the software PWM frequency,
 // affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
 // However, control resolution will be halved for each increment;
diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index 31661a582e..83e6403eba 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -186,12 +186,12 @@
  * THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
  */
 #if ENABLED(THERMAL_PROTECTION_HOTENDS)
-  #define THERMAL_PROTECTION_PERIOD 40        // Seconds
-  #define THERMAL_PROTECTION_HYSTERESIS 4     // Degrees Celsius
+  #define THERMAL_PROTECTION_PERIOD 30        // Seconds
+  #define THERMAL_PROTECTION_HYSTERESIS 15     // Degrees Celsius
 
-  //#define ADAPTIVE_FAN_SLOWING              // Slow part cooling fan if temperature drops
+  #define ADAPTIVE_FAN_SLOWING              // Slow part cooling fan if temperature drops
   #if BOTH(ADAPTIVE_FAN_SLOWING, PIDTEMP)
-    //#define NO_FAN_SLOWING_IN_PID_TUNING    // Don't slow fan speed during M303
+    #define NO_FAN_SLOWING_IN_PID_TUNING    // Don't slow fan speed during M303
   #endif
 
   /**
@@ -206,7 +206,7 @@
    * and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set
    * below 2.
    */
-  #define WATCH_TEMP_PERIOD 20                // Seconds
+  #define WATCH_TEMP_PERIOD 60                // Seconds
   #define WATCH_TEMP_INCREASE 2               // Degrees Celsius
 #endif
 
@@ -214,28 +214,28 @@
  * Thermal Protection parameters for the bed are just as above for hotends.
  */
 #if ENABLED(THERMAL_PROTECTION_BED)
-  #define THERMAL_PROTECTION_BED_PERIOD        20 // Seconds
-  #define THERMAL_PROTECTION_BED_HYSTERESIS     2 // Degrees Celsius
+  #define THERMAL_PROTECTION_BED_PERIOD 80    // Seconds
+  #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
 
   /**
    * As described above, except for the bed (M140/M190/M303).
    */
-  #define WATCH_BED_TEMP_PERIOD                60 // Seconds
-  #define WATCH_BED_TEMP_INCREASE               2 // Degrees Celsius
+  #define WATCH_BED_TEMP_PERIOD 80                // Seconds
+  #define WATCH_BED_TEMP_INCREASE 2               // Degrees Celsius
 #endif
 
 /**
  * Thermal Protection parameters for the heated chamber.
  */
 #if ENABLED(THERMAL_PROTECTION_CHAMBER)
-  #define THERMAL_PROTECTION_CHAMBER_PERIOD    20 // Seconds
+  #define THERMAL_PROTECTION_CHAMBER_PERIOD 20    // Seconds
   #define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
 
   /**
    * Heated chamber watch settings (M141/M191).
    */
-  #define WATCH_CHAMBER_TEMP_PERIOD            60 // Seconds
-  #define WATCH_CHAMBER_TEMP_INCREASE           2 // Degrees Celsius
+  #define WATCH_CHAMBER_TEMP_PERIOD 60            // Seconds
+  #define WATCH_CHAMBER_TEMP_INCREASE 2           // Degrees Celsius
 #endif
 
 #if ENABLED(PIDTEMP)
@@ -413,7 +413,7 @@
 // When first starting the main fan, run it at full speed for the
 // given number of milliseconds.  This gets the fan spinning reliably
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
-//#define FAN_KICKSTART_TIME 100
+#define FAN_KICKSTART_TIME 100
 
 // Some coolers may require a non-zero "off" state.
 //#define FAN_OFF_PWM  1
@@ -474,8 +474,14 @@
  * Multiple extruders can be assigned to the same pin in which case
  * the fan will turn on when any selected extruder is above the threshold.
  */
-#define E0_AUTO_FAN_PIN -1
-#define E1_AUTO_FAN_PIN -1
+#if ENABLED(TREX3)
+  #define E0_AUTO_FAN_PIN  6
+  #define E1_AUTO_FAN_PIN  45
+#else
+  #define E0_AUTO_FAN_PIN -1
+  #define E1_AUTO_FAN_PIN -1
+#endif
+
 #define E2_AUTO_FAN_PIN -1
 #define E3_AUTO_FAN_PIN -1
 #define E4_AUTO_FAN_PIN -1
@@ -503,16 +509,16 @@
 /**
  * M355 Case Light on-off / brightness
  */
-//#define CASE_LIGHT_ENABLE
+#define CASE_LIGHT_ENABLE
 #if ENABLED(CASE_LIGHT_ENABLE)
   //#define CASE_LIGHT_PIN 4                  // Override the default pin if needed
   #define INVERT_CASE_LIGHT false             // Set true if Case Light is ON when pin is LOW
   #define CASE_LIGHT_DEFAULT_ON true          // Set default power-up state on
-  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // Set default power-up brightness (0-255, requires PWM pin)
+  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 255   // Set default power-up brightness (0-255, requires PWM pin)
   //#define CASE_LIGHT_MAX_PWM 128            // Limit pwm
-  //#define CASE_LIGHT_MENU                   // Add Case Light options to the LCD menu
-  //#define CASE_LIGHT_NO_BRIGHTNESS          // Disable brightness control. Enable for non-PWM lighting.
-  //#define CASE_LIGHT_USE_NEOPIXEL           // Use NeoPixel LED as case light, requires NEOPIXEL_LED.
+  #define CASE_LIGHT_MENU                   // Add Case Light options to the LCD menu
+  #define CASE_LIGHT_NO_BRIGHTNESS          // Disable brightness control. Enable for non-PWM lighting.
+  //#define CASE_LIGHT_USE_NEOPIXEL           // Use Neopixel LED as case light, requires NEOPIXEL_LED.
   #if ENABLED(CASE_LIGHT_USE_NEOPIXEL)
     #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White }
   #endif
@@ -619,12 +625,16 @@
  *       Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and
  *       follow with M605 S3 to initiate mirrored movement.
  */
-//#define DUAL_X_CARRIAGE
+#define DUAL_X_CARRIAGE
 #if ENABLED(DUAL_X_CARRIAGE)
   #define X1_MIN_POS X_MIN_POS   // Set to X_MIN_POS
   #define X1_MAX_POS X_BED_SIZE  // Set a maximum so the first X-carriage can't hit the parked second X-carriage
-  #define X2_MIN_POS    80       // Set a minimum to ensure the  second X-carriage can't hit the parked first X-carriage
-  #define X2_MAX_POS   353       // Set this to the distance between toolheads when both heads are homed
+  #define X2_MIN_POS     0       // Set a minimum to ensure the  second X-carriage can't hit the parked first X-carriage
+  #if DISABLED(TREX3) || ENABLED(TREX3_UPGRADE)
+    #define X2_MAX_POS 442       // Set this to the distance between toolheads when both heads are homed
+  #else
+    #define X2_MAX_POS 446       // Set this to the distance between toolheads when both heads are homed
+  #endif
   #define X2_HOME_DIR    1       // Set to 1. The second X-carriage always homes to the maximum endstop position
   #define X2_HOME_POS X2_MAX_POS // Default X2 home position. Set to X2_MAX_POS.
                       // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software
@@ -636,8 +646,9 @@
   #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_AUTO_PARK_MODE
 
   // Default x offset in duplication mode (typically set to half print bed width)
-  #define DEFAULT_DUPLICATION_X_OFFSET 100
-#endif
+  #define DEFAULT_DUPLICATION_X_OFFSET 200
+
+#endif // DUAL_X_CARRIAGE
 
 // Activate a solenoid on the active extruder with M380. Disable all with M381.
 // Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid.
@@ -658,7 +669,7 @@
 
 //#define HOMING_BACKOFF_POST_MM { 2, 2, 2 }  // (mm) Backoff from endstops after homing
 
-//#define QUICK_HOME                          // If G28 contains XY do a diagonal move first
+#define QUICK_HOME                          // If G28 contains XY do a diagonal move first
 //#define HOME_Y_BEFORE_X                     // If G28 contains XY home Y before X
 //#define CODEPENDENT_XY_HOMING               // If X/Y can't home without homing Y/X first
 
@@ -724,7 +735,7 @@
    * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
    * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
    */
-  //#define BLTOUCH_HS_MODE
+  #define BLTOUCH_HS_MODE
 
   // Safety: Enable voltage mode settings in the LCD menu.
   //#define BLTOUCH_LCD_VOLTAGE_MENU
@@ -883,7 +894,7 @@
 // Backlash Compensation
 // Adds extra movement to axes on direction-changes to account for backlash.
 //
-//#define BACKLASH_COMPENSATION
+#define BACKLASH_COMPENSATION
 #if ENABLED(BACKLASH_COMPENSATION)
   // Define values for backlash distance and correction.
   // If BACKLASH_GCODE is enabled these values are the defaults.
@@ -895,7 +906,7 @@
   //#define BACKLASH_SMOOTHING_MM 3 // (mm)
 
   // Add runtime configuration and tuning of backlash values (M425)
-  //#define BACKLASH_GCODE
+  #define BACKLASH_GCODE
 
   #if ENABLED(BACKLASH_GCODE)
     // Measure the Z backlash when probing (G29) and set with "M425 Z"
@@ -925,7 +936,9 @@
  * Note: HOTEND_OFFSET and CALIBRATION_OBJECT_CENTER must be set to within
  *       ±5mm of true values for G425 to succeed.
  */
-//#define CALIBRATION_GCODE
+#if ENABLED(autoCalibrationKit)
+  #define CALIBRATION_GCODE
+#endif
 #if ENABLED(CALIBRATION_GCODE)
 
   //#define CALIBRATION_SCRIPT_PRE  "M117 Starting Auto-Calibration\nT0\nG28\nG12\nM117 Calibrating..."
@@ -945,8 +958,8 @@
   //#define CALIBRATION_REPORTING
 
   // The true location and dimension the cube/bolt/washer on the bed.
-  #define CALIBRATION_OBJECT_CENTER     { 264.0, -22.0,  -2.0 } // mm
-  #define CALIBRATION_OBJECT_DIMENSIONS {  10.0,  10.0,  10.0 } // mm
+  #define CALIBRATION_OBJECT_CENTER     { 264.0, 25.0,  12.5 } // mm
+  #define CALIBRATION_OBJECT_DIMENSIONS {  12.55,  12.55,  4.0 } // mm
 
   // Comment out any sides which are unreachable by the probe. For best
   // auto-calibration results, all sides must be reachable.
@@ -957,12 +970,12 @@
 
   // Probing at the exact top center only works if the center is flat. If
   // probing on a screwhead or hollow washer, probe near the edges.
-  //#define CALIBRATION_MEASURE_AT_TOP_EDGES
+  #define CALIBRATION_MEASURE_AT_TOP_EDGES
 
   // Define the pin to read during calibration
   #ifndef CALIBRATION_PIN
-    //#define CALIBRATION_PIN -1            // Define here to override the default pin
-    #define CALIBRATION_PIN_INVERTING false // Set to true to invert the custom pin
+    #define CALIBRATION_PIN 58 // Override in pins.h or set to -1 to use your Z endstop
+    #define CALIBRATION_PIN_INVERTING true // Set to true to invert the pin
     //#define CALIBRATION_PIN_PULLDOWN
     #define CALIBRATION_PIN_PULLUP
   #endif
@@ -1082,7 +1095,7 @@
   #endif
 
   // Include a page of printer information in the LCD Main Menu
-  //#define LCD_INFO_MENU
+  #define LCD_INFO_MENU
   #if ENABLED(LCD_INFO_MENU)
     //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages
   #endif
@@ -1119,22 +1132,22 @@
 #endif // HAS_LCD_MENU
 
 // Scroll a longer status message into view
-//#define STATUS_MESSAGE_SCROLLING
+#define STATUS_MESSAGE_SCROLLING
 
 // On the Info Screen, display XY with one decimal place when possible
-//#define LCD_DECIMAL_SMALL_XY
+#define LCD_DECIMAL_SMALL_XY
 
 // The timeout (in ms) to return to the status screen from sub-menus
-//#define LCD_TIMEOUT_TO_STATUS 15000
+#define LCD_TIMEOUT_TO_STATUS 15000
 
 // Add an 'M73' G-code to set the current percentage
-//#define LCD_SET_PROGRESS_MANUALLY
+#define LCD_SET_PROGRESS_MANUALLY
 
 // Show the E position (filament used) during printing
 //#define LCD_SHOW_E_TOTAL
 
 #if ENABLED(SHOW_BOOTSCREEN)
-  #define BOOTSCREEN_TIMEOUT 4000        // (ms) Total Duration to display the boot screen(s)
+  #define BOOTSCREEN_TIMEOUT 2000        // (ms) Total Duration to display the boot screen(s)
 #endif
 
 #if EITHER(SDSUPPORT, LCD_SET_PROGRESS_MANUALLY) && ANY(HAS_MARLINUI_U8GLIB, HAS_MARLINUI_HD44780, IS_TFTGLCD_PANEL)
@@ -1164,7 +1177,7 @@
 
   // The standard SD detect circuit reads LOW when media is inserted and HIGH when empty.
   // Enable this option and set to HIGH if your SD cards are incorrectly detected.
-  //#define SD_DETECT_STATE HIGH
+  #define SD_DETECT_STATE HIGH
 
   //#define SDCARD_READONLY                 // Read-only SD card (to save over 2K of flash)
 
@@ -1195,7 +1208,7 @@
    * an option on the LCD screen to continue the print from the last-known
    * point in the file.
    */
-  //#define POWER_LOSS_RECOVERY
+  #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT   false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
     //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
@@ -1251,10 +1264,10 @@
   #endif
 
   // This allows hosts to request long names for files and folders with M33
-  //#define LONG_FILENAME_HOST_SUPPORT
+  #define LONG_FILENAME_HOST_SUPPORT
 
   // Enable this option to scroll long filenames in the SD card menu
-  //#define SCROLL_LONG_FILENAMES
+  #define SCROLL_LONG_FILENAMES
 
   // Leave the heaters on after Stop Print (not recommended!)
   //#define SD_ABORT_NO_COOLDOWN
@@ -1276,7 +1289,7 @@
   /**
    * Auto-report SdCard status with M27 S<seconds>
    */
-  //#define AUTO_REPORT_SD_STATUS
+  #define AUTO_REPORT_SD_STATUS
 
   /**
    * Support for USB thumb drives using an Arduino USB Host Shield or
@@ -1421,7 +1434,7 @@
   //#define STATUS_ALT_FAN_BITMAP     // Use the alternative fan bitmap
   //#define STATUS_FAN_FRAMES 3       // :[0,1,2,3,4] Number of fan animation frames
   //#define STATUS_HEAT_PERCENT       // Show heating in a progress bar
-  //#define BOOT_MARLIN_LOGO_SMALL    // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash)
+  #define BOOT_MARLIN_LOGO_SMALL    // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash)
   //#define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~‭3260 (or ~940) bytes of PROGMEM.
 
   // Frivolous Game Options
@@ -1603,21 +1616,22 @@
  *
  * Warning: Does not respect endstops!
  */
-//#define BABYSTEPPING
+#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
-  //#define INTEGRATED_BABYSTEPPING         // EXPERIMENTAL integration of babystepping into the Stepper ISR
+  #define INTEGRATED_BABYSTEPPING         // EXPERIMENTAL integration of babystepping into the Stepper ISR
   //#define BABYSTEP_WITHOUT_HOMING
   //#define BABYSTEP_ALWAYS_AVAILABLE       // Allow babystepping at all times (not just during movement).
   //#define BABYSTEP_XY                     // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false           // Change if Z babysteps should go the other way
   //#define BABYSTEP_MILLIMETER_UNITS       // Specify BABYSTEP_MULTIPLICATOR_(XY|Z) in mm instead of micro-steps
-  #define BABYSTEP_MULTIPLICATOR_Z  1       // (steps or mm) Steps or millimeter distance for each Z babystep
+  #define BABYSTEP_MULTIPLICATOR_Z  20       // (steps or mm) Steps or millimeter distance for each Z babystep
   #define BABYSTEP_MULTIPLICATOR_XY 1       // (steps or mm) Steps or millimeter distance for each XY babystep
 
-  //#define DOUBLECLICK_FOR_Z_BABYSTEPPING  // Double-click on the Status Screen for Z Babystepping.
+  #define DOUBLECLICK_FOR_Z_BABYSTEPPING  // Double-click on the Status Screen for Z Babystepping.
   #if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING)
     #define DOUBLECLICK_MAX_INTERVAL 1250   // Maximum interval between clicks, in milliseconds.
                                             // Note: Extra time may be added to mitigate controller latency.
+    #define BABYSTEP_ALWAYS_AVAILABLE     // Allow babystepping at all times (not just during movement).
     //#define MOVE_Z_WHEN_IDLE              // Jump to the move Z menu on doubleclick when printer is idle.
     #if ENABLED(MOVE_Z_WHEN_IDLE)
       #define MOVE_Z_IDLE_MULTIPLICATOR 1   // Multiply 1mm by this factor for the move step size.
@@ -1626,10 +1640,10 @@
 
   //#define BABYSTEP_DISPLAY_TOTAL          // Display total babysteps since last G28
 
-  //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
+  #define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
-    //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets
-    //#define BABYSTEP_ZPROBE_GFX_OVERLAY   // Enable graphical overlay on Z-offset editor
+    #define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets
+    #define BABYSTEP_ZPROBE_GFX_OVERLAY   // Enable graphical overlay on Z-offset editor
   #endif
 #endif
 
@@ -1650,10 +1664,12 @@
  *
  * See https://marlinfw.org/docs/features/lin_advance.html for full instructions.
  */
-//#define LIN_ADVANCE
+#if DISABLED(E_2208) || ENABLED(E_Spreadcycle)
+  #define LIN_ADVANCE
+#endif
 #if ENABLED(LIN_ADVANCE)
   //#define EXTRA_LIN_ADVANCE_K // Enable for second linear advance constants
-  #define LIN_ADVANCE_K 0.22    // Unit: mm compression per 1mm/s extruder speed
+  #define LIN_ADVANCE_K 0.0    // Unit: mm compression per 1mm/s extruder speed
   //#define LA_DEBUG            // If enabled, this will generate debug information output over USB.
   //#define EXPERIMENTAL_SCURVE // Enable this option to permit S-Curve Acceleration
 #endif
@@ -1701,10 +1717,10 @@
 
 #if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
-  //#define MESH_MIN_X MESH_INSET
-  //#define MESH_MIN_Y MESH_INSET
-  //#define MESH_MAX_X X_BED_SIZE - (MESH_INSET)
-  //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
+  #define MESH_MIN_X X_MIN_POS + MESH_INSET
+  #define MESH_MIN_Y Y_MIN_POS + MESH_INSET
+  #define MESH_MAX_X X_MAX_POS - MESH_INSET
+  #define MESH_MAX_Y Y_MAX_POS - MESH_INSET
 #endif
 
 /**
@@ -1791,7 +1807,9 @@
 //
 // G2/G3 Arc Support
 //
-#define ARC_SUPPORT                 // Disable this feature to save ~3226 bytes
+#if DISABLED(autoCalibrationKit)
+  #define ARC_SUPPORT               // Disable this feature to save ~3226 bytes
+#endif
 #if ENABLED(ARC_SUPPORT)
   #define MM_PER_ARC_SEGMENT      1 // (mm) Length (or minimum length) of each arc segment
   //#define ARC_SEGMENTS_PER_R    1 // Max segment length, MM_PER = Min
@@ -1893,7 +1911,7 @@
 #elif ENABLED(SDSUPPORT)
   #define BLOCK_BUFFER_SIZE 16
 #else
-  #define BLOCK_BUFFER_SIZE 16
+  #define BLOCK_BUFFER_SIZE 16 // maximize block buffer
 #endif
 
 // @section serial
@@ -1944,7 +1962,7 @@
  * Currently handles M108, M112, M410, M876
  * NOTE: Not yet implemented for all platforms.
  */
-//#define EMERGENCY_PARSER
+#define EMERGENCY_PARSER
 
 // Bad Serial-connections can miss a received command by sending an 'ok'
 // Therefore some clients abort after 30 seconds in a timeout.
@@ -1953,7 +1971,7 @@
 //#define NO_TIMEOUTS 1000 // Milliseconds
 
 // Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary.
-//#define ADVANCED_OK
+#define ADVANCED_OK
 
 // Printrun may have trouble receiving long strings all at once.
 // This option inserts short delays between lines of serial output.
@@ -1987,7 +2005,9 @@
  *
  * Note that M207 / M208 / M209 settings are saved to EEPROM.
  */
-//#define FWRETRACT
+#if ENABLED(ABL_Bilinear)
+  #define FWRETRACT
+#endif
 #if ENABLED(FWRETRACT)
   #define FWRETRACT_AUTORETRACT           // Override slicer retractions
   #if ENABLED(FWRETRACT_AUTORETRACT)
@@ -2015,22 +2035,22 @@
   // Z raise distance for tool-change, as needed for some extruders
   #define TOOLCHANGE_ZRAISE                 2 // (mm)
   //#define TOOLCHANGE_ZRAISE_BEFORE_RETRACT  // Apply raise before swap retraction (if enabled)
-  //#define TOOLCHANGE_NO_RETURN              // Never return to previous position on tool-change
+  #define TOOLCHANGE_NO_RETURN              // Never return to previous position on tool-change
   #if ENABLED(TOOLCHANGE_NO_RETURN)
-    //#define EVENT_GCODE_AFTER_TOOLCHANGE "G12X"   // Extra G-code to run after tool-change
+    #define EVENT_GCODE_AFTER_TOOLCHANGE "G12X"   // Extra G-code to run after tool-change
   #endif
 
   /**
    * Retract and prime filament on tool-change to reduce
    * ooze and stringing and to get cleaner transitions.
    */
-  //#define TOOLCHANGE_FILAMENT_SWAP
+  #define TOOLCHANGE_FILAMENT_SWAP
   #if ENABLED(TOOLCHANGE_FILAMENT_SWAP)
     // Load / Unload
-    #define TOOLCHANGE_FS_LENGTH              12  // (mm) Load / Unload length
-    #define TOOLCHANGE_FS_EXTRA_RESUME_LENGTH  0  // (mm) Extra length for better restart, fine tune by LCD/Gcode)
-    #define TOOLCHANGE_FS_RETRACT_SPEED   (50*60) // (mm/min) (Unloading)
-    #define TOOLCHANGE_FS_UNRETRACT_SPEED (25*60) // (mm/min) (On SINGLENOZZLE or Bowden loading must be slowed down)
+    #define TOOLCHANGE_FS_LENGTH              4  // (mm) Load / Unload length
+    #define TOOLCHANGE_FS_EXTRA_RESUME_LENGTH  2  // (mm) Extra length for better restart, fine tune by LCD/Gcode)
+    #define TOOLCHANGE_FS_RETRACT_SPEED   (50*60) // (mm/m) (Unloading)
+    #define TOOLCHANGE_FS_UNRETRACT_SPEED (25*60) // (mm/m) (On SINGLENOZZLE or Bowden loading must be slowed down)
 
     // Longer prime to clean out a SINGLENOZZLE
     #define TOOLCHANGE_FS_EXTRA_PRIME          0  // (mm) Extra priming length
@@ -2087,49 +2107,49 @@
  * Requires NOZZLE_PARK_FEATURE.
  * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
  */
-//#define ADVANCED_PAUSE_FEATURE
+#define ADVANCED_PAUSE_FEATURE
 #if ENABLED(ADVANCED_PAUSE_FEATURE)
   #define PAUSE_PARK_RETRACT_FEEDRATE         60  // (mm/s) Initial retract feedrate.
-  #define PAUSE_PARK_RETRACT_LENGTH            2  // (mm) Initial retract.
+  #define PAUSE_PARK_RETRACT_LENGTH            4  // (mm) Initial retract.
                                                   // This short retract is done immediately, before parking the nozzle.
-  #define FILAMENT_CHANGE_UNLOAD_FEEDRATE     10  // (mm/s) Unload filament feedrate. This can be pretty fast.
+  #define FILAMENT_CHANGE_UNLOAD_FEEDRATE     41  // (mm/s) Unload filament feedrate. This can be pretty fast.
   #define FILAMENT_CHANGE_UNLOAD_ACCEL        25  // (mm/s^2) Lower acceleration may allow a faster feedrate.
-  #define FILAMENT_CHANGE_UNLOAD_LENGTH      100  // (mm) The length of filament for a complete unload.
+  #define FILAMENT_CHANGE_UNLOAD_LENGTH      70  // (mm) The length of filament for a complete unload.
                                                   //   For Bowden, the full length of the tube and nozzle.
                                                   //   For direct drive, the full length of the nozzle.
                                                   //   Set to 0 for manual unloading.
   #define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE   6  // (mm/s) Slow move when starting load.
   #define FILAMENT_CHANGE_SLOW_LOAD_LENGTH     0  // (mm) Slow length, to allow time to insert material.
                                                   // 0 to disable start loading and skip to fast load only
-  #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE   6  // (mm/s) Load filament feedrate. This can be pretty fast.
+  #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE  30  // (mm/s) Load filament feedrate. This can be pretty fast.
   #define FILAMENT_CHANGE_FAST_LOAD_ACCEL     25  // (mm/s^2) Lower acceleration may allow a faster feedrate.
-  #define FILAMENT_CHANGE_FAST_LOAD_LENGTH     0  // (mm) Load length of filament, from extruder gear to nozzle.
+  #define FILAMENT_CHANGE_FAST_LOAD_LENGTH    50  // (mm) Load length of filament, from extruder gear to nozzle.
                                                   //   For Bowden, the full length of the tube and nozzle.
                                                   //   For direct drive, the full length of the nozzle.
   //#define ADVANCED_PAUSE_CONTINUOUS_PURGE       // Purge continuously up to the purge length until interrupted.
   #define ADVANCED_PAUSE_PURGE_FEEDRATE        3  // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
-  #define ADVANCED_PAUSE_PURGE_LENGTH         50  // (mm) Length to extrude after loading.
+  #define ADVANCED_PAUSE_PURGE_LENGTH         20  // (mm) Length to extrude after loading.
                                                   //   Set to 0 for manual extrusion.
                                                   //   Filament can be extruded repeatedly from the Filament Change menu
                                                   //   until extrusion is consistent, and to purge old filament.
-  #define ADVANCED_PAUSE_RESUME_PRIME          0  // (mm) Extra distance to prime nozzle after returning from park.
-  //#define ADVANCED_PAUSE_FANS_PAUSE             // Turn off print-cooling fans while the machine is paused.
+  #define ADVANCED_PAUSE_RESUME_PRIME          2  // (mm) Extra distance to prime nozzle after returning from park.
+  #define ADVANCED_PAUSE_FANS_PAUSE             // Turn off print-cooling fans while the machine is paused.
 
                                                   // Filament Unload does a Retract, Delay, and Purge first:
-  #define FILAMENT_UNLOAD_PURGE_RETRACT       13  // (mm) Unload initial retract length.
-  #define FILAMENT_UNLOAD_PURGE_DELAY       5000  // (ms) Delay for the filament to cool after retract.
+  #define FILAMENT_UNLOAD_PURGE_RETRACT       4  // (mm) Unload initial retract length.
+  #define FILAMENT_UNLOAD_PURGE_DELAY       2000  // (ms) Delay for the filament to cool after retract.
   #define FILAMENT_UNLOAD_PURGE_LENGTH         8  // (mm) An unretract is done, then this length is purged.
   #define FILAMENT_UNLOAD_PURGE_FEEDRATE      25  // (mm/s) feedrate to purge before unload
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT           45  // (seconds) Time limit before the nozzle is turned off for safety.
-  #define FILAMENT_CHANGE_ALERT_BEEPS         10  // Number of alert beeps to play when a response is needed.
+  #define FILAMENT_CHANGE_ALERT_BEEPS          1  // Number of alert beeps to play when a response is needed.
   #define PAUSE_PARK_NO_STEPPER_TIMEOUT           // Enable for XYZ steppers to stay powered on during filament change.
 
-  //#define PARK_HEAD_ON_PAUSE                    // Park the nozzle during pause and filament change.
-  //#define HOME_BEFORE_FILAMENT_CHANGE           // If needed, home before parking for filament change
+  #define PARK_HEAD_ON_PAUSE                    // Park the nozzle during pause and filament change.
+  #define HOME_BEFORE_FILAMENT_CHANGE           // If needed, home before parking for filament change
 
-  //#define FILAMENT_LOAD_UNLOAD_GCODES           // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
-  //#define FILAMENT_UNLOAD_ALL_EXTRUDERS         // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
+  #define FILAMENT_LOAD_UNLOAD_GCODES           // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
+  #define FILAMENT_UNLOAD_ALL_EXTRUDERS         // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
 #endif
 
 // @section tmc
@@ -2932,13 +2952,18 @@
  * See https://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
  */
 //#define SPINDLE_FEATURE
-//#define LASER_FEATURE
+#if ENABLED(TREX3)
+  #define LASER_FEATURE
+#endif
 #if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
-  #define SPINDLE_LASER_ACTIVE_STATE    LOW    // Set to "HIGH" if the on/off function is active HIGH
-  #define SPINDLE_LASER_PWM             true   // Set to "true" if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      false  // Set to "true" if the speed/power goes up when you want it to go slower
+  //#define SHOW_CUTTER_ICON
+  #define SPINDLE_LASER_ACTIVE_HIGH     true  // Set to "true" if the on/off function is active HIGH
+  #define SPINDLE_LASER_PWM             false   // Set to "true" if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
 
-  #define SPINDLE_LASER_FREQUENCY       2500   // (Hz) Spindle/laser frequency (only on supported HALs: AVR and LPC)
+  #if ENABLED(SPINDLE_LASER_PWM)
+    //#define SPINDLE_LASER_FREQUENCY       2500   // (Hz) Spindle/laser frequency (only on supported HALs: AVR and LPC)
+  #endif
 
   /**
    * Speed / Power can be set ('M3 S') and displayed in terms of:
@@ -2963,8 +2988,8 @@
     #define SPINDLE_CHANGE_DIR_STOP            // Enable if the spindle should stop before changing spin direction
     #define SPINDLE_INVERT_DIR          false  // Set to "true" if the spin direction is reversed
 
-    #define SPINDLE_LASER_POWERUP_DELAY   5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
-    #define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
+    #define SPINDLE_LASER_POWERUP_DELAY   1 // (ms) Delay to allow the spindle/laser to come up to speed/power
+    #define SPINDLE_LASER_POWERDOWN_DELAY 1 // (ms) Delay to allow the spindle to stop
 
     /**
      * M3/M4 Power Equation
@@ -3005,7 +3030,7 @@
        * - Ramps the power up every N steps to approximate the speed trapezoid.
        * - Due to the limited power resolution this is only approximate.
        */
-      #define LASER_POWER_INLINE_TRAPEZOID
+      //#define LASER_POWER_INLINE_TRAPEZOID
 
       /**
        * Continuously calculate the current power (nominal_power * current_rate / nominal_rate).
@@ -3261,27 +3286,37 @@
 /**
  * User-defined menu items that execute custom GCode
  */
-//#define CUSTOM_USER_MENUS
+#define CUSTOM_USER_MENUS
 #if ENABLED(CUSTOM_USER_MENUS)
-  //#define CUSTOM_USER_MENU_TITLE "Custom Commands"
-  #define USER_SCRIPT_DONE "M117 User Script Done"
+  //#define USER_SCRIPT_DONE "M117 User Script Done"
+  #define CUSTOM_USER_MENU_TITLE "Setup"
   #define USER_SCRIPT_AUDIBLE_FEEDBACK
-  //#define USER_SCRIPT_RETURN  // Return to status screen after a script
+  #define USER_SCRIPT_RETURN  // Return to status screen after a script
 
-  #define USER_DESC_1 "Home & UBL Info"
-  #define USER_GCODE_1 "G28\nG29 W"
+  #if ENABLED(TREX3)
+    #define COMMFANNSPEED " "
+  #else
+    #define COMMFANNSPEED  "M106 S128 \n"
+  #endif
 
-  #define USER_DESC_2 "Preheat for " PREHEAT_1_LABEL
-  #define USER_GCODE_2 "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND)
+  #define USER_DESC_1 "Mesh Setup"
+  #define USER_DESC_3 "Prep for Z Adjust"
+  #if ENABLED(ABL_Bilinear)
+    #define USER_GCODE_1 "M502 \n M500 \n M501 \n M190 S75 \n G28 \n G29 \n M500 \n G28 \n M420 S1 \n " COMMFANNSPEED " M109 S225 \n G1 X100 Y 100 \n G1 Z0 \n M77 \n M117 Set Z Offset"
+    #define USER_GCODE_3 "M190 S75 \n " COMMFANNSPEED " M104 235 \n G28 \n M420 S1 \n G1 X100 Y 100 \n G1 Z0"
+  #else
+    #define USER_GCODE_1 "M502 \n M500 \n M501 \n M190 S75 \n G28 \n G29 P1 \n G29 S1 \n G29 S0 \n G29 F 10.0 \n G29 A \n M500 \n G28 \n G29 L1 \n " COMMFANNSPEED " M109 S225 \n G1 X150 Y 150 \n G1 Z0 \n M77 \n M117 Set Z Offset"
+    #define USER_GCODE_3 "M190 S75 \n " COMMFANNSPEED " M104 235 \n G28 \n G29 L1 \n G1 X100 Y 100 \n G1 Z0"
+  #endif
 
-  #define USER_DESC_3 "Preheat for " PREHEAT_2_LABEL
-  #define USER_GCODE_3 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND)
+  #define USER_DESC_4 "Fill Mesh Points"
+  #define USER_GCODE_4 "G29 P3 \n G29 P3 \n G29 P3 \n G29 T"
 
-  #define USER_DESC_4 "Heat Bed/Home/Level"
-  #define USER_GCODE_4 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29"
+  #define USER_DESC_2 "PID Bed"
+  #define USER_GCODE_2 "M303 C4 S75 E-1 U \n M500 \n M117 PID Tune Done"
 
-  #define USER_DESC_5 "Home & Info"
-  #define USER_GCODE_5 "G28\nM503"
+  #define USER_DESC_5 "Run Mesh Validation"
+  #define USER_GCODE_5 "G26"
 #endif
 
 /**
@@ -3298,10 +3333,10 @@
  * Host Prompt Support enables Marlin to use the host for user prompts so
  * filament runout and other processes can be managed from the host side.
  */
-//#define HOST_ACTION_COMMANDS
+#define HOST_ACTION_COMMANDS
 #if ENABLED(HOST_ACTION_COMMANDS)
-  //#define HOST_PROMPT_SUPPORT
-  //#define HOST_START_MENU_ITEM  // Add a menu item that tells the host to start
+  #define HOST_PROMPT_SUPPORT
+  #define HOST_START_MENU_ITEM  // Add a menu item that tells the host to start
 #endif
 
 /**
@@ -3309,7 +3344,7 @@
  *
  * Implement M486 to allow Marlin to skip objects
  */
-//#define CANCEL_OBJECTS
+#define CANCEL_OBJECTS
 
 /**
  * I2C position encoders for closed loop control.
diff --git a/Marlin/Version.h b/Marlin/Version.h
index fe0724fbfc..6bbf3a221d 100644
--- a/Marlin/Version.h
+++ b/Marlin/Version.h
@@ -28,25 +28,25 @@
 /**
  * Marlin release version identifier
  */
-//#define SHORT_BUILD_VERSION "bugfix-2.0.x"
+#define SHORT_BUILD_VERSION "2.0.5_TR25"
 
 /**
  * Verbose version identifier which should contain a reference to the location
  * from where the binary was downloaded or the source code was compiled.
  */
-//#define DETAILED_BUILD_VERSION SHORT_BUILD_VERSION
+#define DETAILED_BUILD_VERSION SHORT_BUILD_VERSION " TM3D"
 
 /**
  * The STRING_DISTRIBUTION_DATE represents when the binary file was built,
  * here we define this default string as the date where the latest release
  * version was tagged.
  */
-//#define STRING_DISTRIBUTION_DATE "2019-07-10"
+#define STRING_DISTRIBUTION_DATE "2020-06-15"
 
 /**
  * Defines a generic printer name to be output to the LCD after booting Marlin.
  */
-//#define MACHINE_NAME "3D Printer"
+#define MACHINE_NAME "TM3D Trex"
 
 /**
  * The SOURCE_CODE_URL is the location where users will find the Marlin Source
@@ -54,7 +54,7 @@
  * has a distinct Github fork— the Source Code URL should just be the main
  * Marlin repository.
  */
-//#define SOURCE_CODE_URL "https://github.com/MarlinFirmware/Marlin"
+#define SOURCE_CODE_URL "https://github.com/InsanityAutomation/Marlin/tree/TM_Trex2+_2.0.x"
 
 /**
  * Default generic printer UUID.
@@ -65,7 +65,7 @@
  * The WEBSITE_URL is the location where users can get more information such as
  * documentation about a specific Marlin release.
  */
-//#define WEBSITE_URL "https://marlinfw.org"
+#define WEBSITE_URL "tinymachines3d.com"
 
 /**
  * Set the vendor info the serial USB interface, if changable
diff --git a/Marlin/_Bootscreen.h b/Marlin/_Bootscreen.h
new file mode 100644
index 0000000000..d262102e47
--- /dev/null
+++ b/Marlin/_Bootscreen.h
@@ -0,0 +1,93 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Custom Bitmap for splashscreen
+ *
+ * You may use one of the following tools to generate the C++ bitmap array from
+ * a black and white image:
+ *
+ *  - http://www.marlinfw.org/tools/u8glib/converter.html
+ *  - http://www.digole.com/tools/PicturetoC_Hex_converter.php
+ */
+
+#define CUSTOM_BOOTSCREEN_TIMEOUT   2500
+#define CUSTOM_BOOTSCREEN_BMPWIDTH  128
+#define CUSTOM_BOOTSCREEN_INVERTED
+
+const unsigned char custom_start_bmp[] PROGMEM = {
+  B11111101,B01010101,B01010101,B01010101,B01010101,B01010101,B01011111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,
+  B11111110,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,
+  B11111101,B00000000,B00000000,B00000111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,
+  B11111110,B00000111,B11000000,B00000101,B01010101,B01010101,B01010101,B01010101,B01010101,B01011111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,
+  B11111100,B00001010,B00100000,B00000110,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,
+  B11111110,B00010100,B00010000,B00000101,B00000000,B00000000,B00000111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,
+  B11111100,B00101000,B00001000,B00000110,B00000111,B11000000,B00000101,B01010101,B01010101,B01010101,B01010101,B01010101,B01011111,B11111111,B11111111,B11111111,
+  B11111110,B01010100,B00000100,B00000100,B00001010,B00100000,B00000110,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11111111,B11111111,B11111111,
+  B11111100,B01100000,B00000100,B00000110,B00010100,B00010000,B00000101,B00000000,B00000000,B00000111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,
+  B11111110,B01010000,B00000100,B00000100,B00101000,B00001000,B00000110,B00000111,B11000000,B00000101,B01010101,B01010101,B01010101,B01010101,B01010101,B01011111,
+  B11111100,B01100000,B00000100,B00000110,B01010100,B00000100,B00000100,B00001010,B00100000,B00000110,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,
+  B11111110,B01010100,B00000100,B00011100,B01100000,B00000100,B00000110,B00010100,B00010000,B00000101,B00000000,B00000000,B00000000,B00000000,B00000000,B00011111,
+  B11111100,B00101000,B00001000,B00101110,B01010000,B00000100,B00000100,B00101000,B00001000,B00000110,B00000111,B11000000,B00000000,B00000001,B11110000,B00111111,
+  B11111110,B00010100,B00010000,B01010100,B01100000,B00000100,B00000110,B01010100,B00000100,B00000100,B00001010,B00100000,B00000000,B00000010,B00001000,B00011111,
+  B11111100,B00001010,B00100000,B01100110,B01010100,B00000100,B00011100,B01100000,B00000100,B00000110,B00010100,B00010000,B00000000,B00000101,B00000100,B00111111,
+  B11111110,B00000111,B11000000,B01010100,B00101000,B00001000,B00101110,B01010000,B00000100,B00000100,B00101000,B00001000,B00000000,B00001010,B00000010,B00011111,
+  B11111100,B00000000,B00000000,B00101110,B00010100,B00010000,B01010100,B01100000,B00000100,B00000110,B01010100,B00000100,B00000000,B00010101,B00000001,B00111111,
+  B11111110,B00000000,B00000000,B00011100,B00001010,B00100000,B01100110,B01010100,B00000100,B00011100,B01100000,B00000100,B00000000,B00011000,B00000001,B00011111,
+  B11111100,B00000000,B00000000,B00000110,B00000111,B11000000,B01010100,B00101000,B00001000,B00101110,B01010000,B00000100,B00000000,B00010100,B00000001,B00111111,
+  B11111110,B00000000,B00000000,B00000100,B00000000,B00000000,B00101110,B00010100,B00010000,B01010100,B01100000,B00000100,B00000000,B00011000,B00000001,B00011111,
+  B11111100,B11111111,B11111111,B11111110,B00000000,B00000000,B00011100,B00001010,B00100000,B01100110,B01010100,B00000100,B00011100,B00010101,B00000001,B00111111,
+  B11111110,B11010101,B01010101,B01010100,B00000000,B00000000,B00000110,B00000111,B11000000,B01010100,B00101000,B00001000,B00101010,B00001010,B00000010,B00011111,
+  B11111100,B10000100,B00010000,B01000110,B00000000,B00000000,B00000100,B00000000,B00000000,B00101110,B00010100,B00010000,B01010001,B00000101,B00000100,B00111111,
+  B11111110,B11000100,B00010000,B01000100,B11111111,B11111111,B11111110,B00000000,B00000000,B00011100,B00001010,B00100000,B01100001,B00000010,B10001000,B00011111,
+  B11111100,B10000100,B00010000,B01000110,B11010101,B01010101,B01010100,B00000000,B00000000,B00000110,B00000111,B11000000,B01010001,B00000001,B11110000,B00111111,
+  B11111110,B10000100,B00010000,B01000100,B10000100,B00010000,B01000110,B00000000,B00000000,B00000100,B00000000,B00000000,B00101010,B00000000,B00000000,B00011111,
+  B11111100,B11000100,B00010000,B01000110,B11000100,B00010000,B01000100,B11111111,B11111111,B11111110,B00000000,B00000000,B00011100,B00000000,B00000000,B00111111,
+  B11111110,B10000100,B00010000,B01000100,B10000100,B00010000,B01000110,B11010101,B01010101,B01010100,B00000000,B00000000,B00000000,B00000000,B00000000,B00011111,
+  B11111100,B11010101,B01010101,B01010110,B10000100,B00010000,B01000100,B10000100,B00010000,B01000110,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,
+  B11111100,B11111111,B11111111,B11111100,B11000100,B00010000,B01000110,B11000100,B00010000,B01000100,B11111111,B11111111,B11111111,B11111111,B11111111,B10011111,
+  B11111110,B00000000,B00000000,B00000110,B10000100,B00010000,B01000100,B10000100,B00010000,B01000110,B11010101,B01010101,B01010101,B01010101,B01010101,B10111111,
+  B11111101,B01010101,B01010101,B01010100,B11010101,B01010101,B01010110,B10000100,B00010000,B01000100,B10000100,B00010000,B01000001,B00000100,B00010000,B10011111,
+  B11111111,B11111111,B11111111,B11111100,B11111111,B11111111,B11111100,B11000100,B00010000,B01000110,B11000100,B00010000,B01000001,B00000100,B00010001,B10111111,
+  B11111111,B11111111,B11111111,B11111110,B00000000,B00000000,B00000110,B10000100,B00010000,B01000100,B10000100,B00010000,B01000001,B00000100,B00010000,B10011111,
+  B11111111,B11111111,B11111111,B11111101,B01010101,B01010101,B01010100,B11010101,B01010101,B01010110,B10000100,B00010000,B01000001,B00000100,B00010000,B10011111,
+  B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111100,B11111111,B11111111,B11111100,B11000100,B00010000,B01000001,B00000100,B00010001,B10111111,
+  B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111110,B00000000,B00000000,B00000110,B10000100,B00010000,B01000001,B00000100,B00010000,B10011111,
+  B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111101,B01010101,B01010101,B01010100,B11010101,B01010101,B01010101,B01010101,B01010101,B10111111,
+  B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111100,B11111111,B11111111,B11111111,B11111111,B11111111,B10011111,
+  B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111110,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,
+  B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111101,B01010101,B01010101,B01010101,B01010101,B01010101,B01011111,
+  B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,
+  B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,
+  B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,
+  B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,
+  B11100000,B00101110,B11111011,B01111101,B11111011,B11111011,B11001111,B11000001,B11011111,B10111011,B00111110,B11000000,B11100001,B11111110,B00111100,B00011111,
+  B11111101,B11101110,B01111011,B00111001,B11111001,B11110011,B11001111,B10011110,B11011111,B10111011,B00111110,B11011111,B11011110,B11111100,B11011101,B11100111,
+  B11111101,B11101110,B00111011,B10111011,B11111001,B11101011,B11010111,B10111111,B01011111,B10111011,B01011110,B11011111,B11011110,B11111101,B11101101,B11110111,
+  B11111101,B11101110,B10111011,B11010011,B11111010,B11101011,B10110111,B00111111,B11011111,B10111011,B01001110,B11011111,B11011111,B11111111,B11001101,B11110011,
+  B11111101,B11101110,B11011011,B11000111,B11111010,B11101011,B10111011,B01111111,B11000000,B00111011,B01101110,B11000000,B11100011,B11111111,B00011101,B11110011,
+  B11111101,B11101110,B11001011,B11101111,B11111010,B11011011,B10111011,B01111111,B11011111,B10111011,B01100110,B11011111,B11111000,B11111111,B11001101,B11110011,
+  B11111101,B11101110,B11101011,B11101111,B11111011,B01011011,B00000011,B00111111,B01011111,B10111011,B01110110,B11011111,B11111110,B01111111,B11101101,B11110011,
+  B11111101,B11101110,B11110011,B11101111,B11111011,B01011011,B01111001,B10111110,B11011111,B10111011,B01111010,B11011111,B11011110,B01111101,B11101101,B11110111,
+  B11111101,B11101110,B11110011,B11101111,B11111011,B10111010,B11111101,B10011110,B11011111,B10111011,B01111100,B11011111,B11011110,B11111101,B11001101,B11100111,
+  B11111101,B11101110,B11111011,B11101111,B11111011,B10111010,B11111101,B11000001,B11011111,B10111011,B01111110,B11000000,B11100000,B11111110,B00011100,B00011111
+};
diff --git a/Marlin/_Statusscreen.h b/Marlin/_Statusscreen.h
new file mode 100644
index 0000000000..d0450837ab
--- /dev/null
+++ b/Marlin/_Statusscreen.h
@@ -0,0 +1,74 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Custom Status Screen bitmap
+ *
+ * Place this file in the root with your configuration files
+ * and enable CUSTOM_STATUS_SCREEN_IMAGE in Configuration.h.
+ *
+ * Use the Marlin Bitmap Converter to make your own:
+ * http://marlinfw.org/tools/u8glib/converter.html
+ */
+
+//
+// Status Screen Logo bitmap
+//
+#define STATUS_LOGO_Y            3
+#define STATUS_LOGO_WIDTH       24
+
+const unsigned char status_logo_bmp[] PROGMEM = {
+  B11111111,B11111111,B11111111,
+  B10000000,B00000000,B00000001,
+  B10001110,B00000000,B11100001,
+  B10011111,B00000001,B11110001,
+  B10010011,B10000001,B00111001,
+  B10011111,B10000001,B11111001,
+  B10011111,B10000001,B11111001,
+  B10011111,B10111001,B11111001,
+  B10001111,B00101000,B11110001,
+  B10000000,B00111000,B00000001,
+  B10000000,B00000000,B00000001,
+  B10011111,B11111111,B11111001,
+  B10010001,B01110100,B10011001,
+  B10011011,B00000110,B10101001,
+  B10011011,B01010100,B10101001,
+  B10011011,B01010110,B10101001,
+  B10011011,B01010100,B10011001,
+  B10011111,B11111111,B11111001,
+  B11111111,B11111111,B11111111
+};
+
+//
+// Use default bitmaps
+//
+#define STATUS_HOTEND_ANIM
+#define STATUS_BED_ANIM
+#if HOTENDS < 2
+  #define STATUS_LOGO_X          8
+  #define STATUS_HEATERS_X      40
+  #define STATUS_BED_X          72
+#else
+  #define STATUS_LOGO_X          0
+  #define STATUS_HEATERS_X      32
+  #define STATUS_BED_X          80
+#endif