diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h index 1d7c1a7277..7f06b0a0a4 100644 --- a/Marlin/Configuration_adv.h +++ b/Marlin/Configuration_adv.h @@ -307,11 +307,11 @@ #define THERMAL_PROTECTION_PERIOD 40 // (seconds) #define THERMAL_PROTECTION_HYSTERESIS 4 // (°C) - //#define ADAPTIVE_FAN_SLOWING // Slow down the part-cooling fan if the temperature drops + #define ADAPTIVE_FAN_SLOWING // Slow down the part-cooling fan if the temperature drops #if ENABLED(ADAPTIVE_FAN_SLOWING) //#define REPORT_ADAPTIVE_FAN_SLOWING // Report fan slowing activity to the console #if ANY(MPCTEMP, PIDTEMP) - //#define TEMP_TUNING_MAINTAIN_FAN // Don't slow down the fan speed during M303 or M306 T + #define TEMP_TUNING_MAINTAIN_FAN // Don't slow down the fan speed during M303 or M306 T #endif #endif @@ -335,7 +335,7 @@ * Thermal Protection parameters for the bed are just as above for hotends. */ #if ENABLED(THERMAL_PROTECTION_BED) - #define THERMAL_PROTECTION_BED_PERIOD 20 // (seconds) + #define THERMAL_PROTECTION_BED_PERIOD 90 // (seconds) #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // (°C) /** @@ -547,10 +547,10 @@ * Hotend Idle Timeout * Prevent filament in the nozzle from charring and causing a critical jam. */ -//#define HOTEND_IDLE_TIMEOUT +#define HOTEND_IDLE_TIMEOUT #if ENABLED(HOTEND_IDLE_TIMEOUT) - #define HOTEND_IDLE_TIMEOUT_SEC (5*60) // (seconds) Time without extruder movement to trigger protection - #define HOTEND_IDLE_MIN_TRIGGER 180 // (°C) Minimum temperature to enable hotend protection + #define HOTEND_IDLE_TIMEOUT_SEC (30*60) // (seconds) Time without extruder movement to trigger protection + #define HOTEND_IDLE_MIN_TRIGGER 170 // (°C) Minimum temperature to enable hotend protection #define HOTEND_IDLE_NOZZLE_TARGET 0 // (°C) Safe temperature for the nozzle after timeout #define HOTEND_IDLE_BED_TARGET 0 // (°C) Safe temperature for the bed after timeout #endif @@ -602,8 +602,8 @@ * gets it spinning reliably for a short time before setting the requested speed. * (Does not work on Sanguinololu with FAN_SOFT_PWM.) */ -//#define FAN_KICKSTART_TIME 100 // (ms) -//#define FAN_KICKSTART_POWER 180 // 64-255 +#define FAN_KICKSTART_TIME 100 // (ms) +#define FAN_KICKSTART_POWER 180 // 64-255 // Some coolers may require a non-zero "off" state. //#define FAN_OFF_PWM 1 @@ -931,7 +931,7 @@ //#define HOMING_BACKOFF_POST_MM { 2, 2, 2 } // (linear=mm, rotational=°) Backoff from endstops after homing //#define XY_COUNTERPART_BACKOFF_MM 0 // (mm) Backoff X after homing Y, and vice-versa -//#define QUICK_HOME // If G28 contains XY do a diagonal move first +#define QUICK_HOME // If G28 contains XY do a diagonal move first //#define HOME_Y_BEFORE_X // If G28 contains XY home Y before X //#define HOME_Z_FIRST // Home Z first. Requires a real endstop (not a probe). //#define CODEPENDENT_XY_HOMING // If X/Y can't home without homing Y/X first @@ -1020,7 +1020,7 @@ * Z Steppers Auto-Alignment * Add the G34 command to align multiple Z steppers using a bed probe. */ -//#define Z_STEPPER_AUTO_ALIGN +#define Z_STEPPER_AUTO_ALIGN #if ENABLED(Z_STEPPER_AUTO_ALIGN) /** * Define probe X and Y positions for Z1, Z2 [, Z3 [, Z4]] @@ -1281,7 +1281,7 @@ // Backlash Compensation // Adds extra movement to axes on direction-changes to account for backlash. // -//#define BACKLASH_COMPENSATION +#define BACKLASH_COMPENSATION #if ENABLED(BACKLASH_COMPENSATION) // Define values for backlash distance and correction. // If BACKLASH_GCODE is enabled these values are the defaults. @@ -1296,7 +1296,7 @@ //#define BACKLASH_SMOOTHING_MM 3 // (mm) // Add runtime configuration and tuning of backlash values (M425) - //#define BACKLASH_GCODE + #define BACKLASH_GCODE #if ENABLED(BACKLASH_GCODE) // Measure the Z backlash when probing (G29) and set with "M425 Z" @@ -1342,7 +1342,7 @@ #define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm #define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm - // Uncomment to enable reporting (required for "G425 V", but consumes flash). + // Uncomment to enable reporting (required for "G425 V", but consumes PROGMEM). //#define CALIBRATION_REPORTING // The true location and dimension the cube/bolt/washer on the bed. @@ -1528,7 +1528,7 @@ #endif // Include a page of printer information in the LCD Main Menu - //#define LCD_INFO_MENU + #define LCD_INFO_MENU #if ENABLED(LCD_INFO_MENU) //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages #endif @@ -1580,7 +1580,7 @@ #define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving lots of flash) #endif #if HAS_MARLINUI_U8GLIB - //#define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~3260 (or ~940) bytes of flash. + #define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~3260 (or ~940) bytes of flash. #endif #if ANY(HAS_MARLINUI_U8GLIB, TOUCH_UI_FTDI_EVE) //#define SHOW_CUSTOM_BOOTSCREEN // Show the bitmap in Marlin/_Bootscreen.h on startup. @@ -1599,10 +1599,10 @@ #endif // The timeout to return to the status screen from sub-menus - //#define LCD_TIMEOUT_TO_STATUS 15000 // (ms) + #define LCD_TIMEOUT_TO_STATUS 15000 // (ms) // Scroll a longer status message into view - //#define STATUS_MESSAGE_SCROLLING + #define STATUS_MESSAGE_SCROLLING // Apply a timeout to low-priority status messages //#define STATUS_MESSAGE_TIMEOUT_SEC 30 // (seconds) @@ -1654,7 +1654,7 @@ #endif // Add 'M73' to set print job progress, overrides Marlin's built-in estimate -//#define SET_PROGRESS_MANUALLY +#define SET_PROGRESS_MANUALLY #if ENABLED(SET_PROGRESS_MANUALLY) #define SET_PROGRESS_PERCENT // Add 'P' parameter to set percentage done #define SET_REMAINING_TIME // Add 'R' parameter to set remaining time @@ -1806,13 +1806,13 @@ // Allow international symbols in long filenames. To display correctly, the // LCD's font must contain the characters. Check your selected LCD language. - //#define UTF_FILENAME_SUPPORT + #define UTF_FILENAME_SUPPORT - //#define LONG_FILENAME_HOST_SUPPORT // Get the long filename of a file/folder with 'M33 ' and list long filenames with 'M20 L' + #define LONG_FILENAME_HOST_SUPPORT // Get the long filename of a file/folder with 'M33 ' and list long filenames with 'M20 L' //#define LONG_FILENAME_WRITE_SUPPORT // Create / delete files with long filenames via M28, M30, and Binary Transfer Protocol //#define M20_TIMESTAMP_SUPPORT // Include timestamps by adding the 'T' flag to M20 commands - //#define SCROLL_LONG_FILENAMES // Scroll long filenames in the SD card menu + #define SCROLL_LONG_FILENAMES // Scroll long filenames in the SD card menu //#define SD_ABORT_NO_COOLDOWN // Leave the heaters on after Stop Print (not recommended!) @@ -2263,18 +2263,18 @@ * * Warning: Does not respect endstops! */ -//#define BABYSTEPPING +#define BABYSTEPPING #if ENABLED(BABYSTEPPING) //#define EP_BABYSTEPPING // M293/M294 babystepping with EMERGENCY_PARSER support //#define BABYSTEP_WITHOUT_HOMING - //#define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement) + #define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement) //#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA! //#define BABYSTEP_INVERT_Z // Enable if Z babysteps should go the other way //#define BABYSTEP_MILLIMETER_UNITS // Specify BABYSTEP_MULTIPLICATOR_(XY|Z) in mm instead of micro-steps - #define BABYSTEP_MULTIPLICATOR_Z 1 // (steps or mm) Steps or millimeter distance for each Z babystep + #define BABYSTEP_MULTIPLICATOR_Z 25 // (steps or mm) Steps or millimeter distance for each Z babystep #define BABYSTEP_MULTIPLICATOR_XY 1 // (steps or mm) Steps or millimeter distance for each XY babystep - //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping. + #define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping. #if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING) #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds. // Note: Extra time may be added to mitigate controller latency. @@ -2286,10 +2286,10 @@ //#define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28 - //#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping + #define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping #if ENABLED(BABYSTEP_ZPROBE_OFFSET) //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets - //#define BABYSTEP_GFX_OVERLAY // Enable graphical overlay on Z-offset editor + #define BABYSTEP_GFX_OVERLAY // Enable graphical overlay on Z-offset editor #endif #endif @@ -2310,7 +2310,7 @@ * * See https://marlinfw.org/docs/features/lin_advance.html for full instructions. */ -//#define LIN_ADVANCE +#define LIN_ADVANCE #if ENABLED(LIN_ADVANCE) #if ENABLED(DISTINCT_E_FACTORS) #define ADVANCE_K { 0.22 } // (mm) Compression length per 1mm/s extruder speed, per extruder @@ -2319,7 +2319,7 @@ #endif //#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L. //#define LA_DEBUG // Print debug information to serial during operation. Disable for production use. - //#define ALLOW_LOW_EJERK // Allow a DEFAULT_EJERK value of <10. Recommended for direct drive hotends. + #define ALLOW_LOW_EJERK // Allow a DEFAULT_EJERK value of <10. Recommended for direct drive hotends. //#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz. #endif @@ -2504,7 +2504,7 @@ #endif // G5 Bézier Curve Support with XYZE destination and IJPQ offsets -//#define BEZIER_CURVE_SUPPORT // Requires ~2666 bytes +#define BEZIER_CURVE_SUPPORT // Requires ~2666 bytes #if ANY(ARC_SUPPORT, BEZIER_CURVE_SUPPORT) //#define CNC_WORKSPACE_PLANES // Allow G2/G3/G5 to operate in XY, ZX, or YZ planes @@ -2596,16 +2596,16 @@ #if ALL(HAS_MEDIA, DIRECT_STEPPING) #define BLOCK_BUFFER_SIZE 8 #elif HAS_MEDIA - #define BLOCK_BUFFER_SIZE 16 + #define BLOCK_BUFFER_SIZE 32 #else - #define BLOCK_BUFFER_SIZE 16 + #define BLOCK_BUFFER_SIZE 32 #endif // @section serial // The ASCII buffer for serial input #define MAX_CMD_SIZE 96 -#define BUFSIZE 4 +#define BUFSIZE 16 // Transmission to Host Buffer Size // To save 386 bytes of flash (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0. @@ -2652,7 +2652,7 @@ * Currently handles M108, M112, M410, M876 * NOTE: Not yet implemented for all platforms. */ -//#define EMERGENCY_PARSER +#define EMERGENCY_PARSER /** * Realtime Reporting (requires EMERGENCY_PARSER) @@ -2683,7 +2683,7 @@ //#define NO_TIMEOUTS 1000 // (ms) // Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary. -//#define ADVANCED_OK +#define ADVANCED_OK // Printrun may have trouble receiving long strings all at once. // This option inserts short delays between lines of serial output. @@ -2885,7 +2885,7 @@ * * Enable PARK_HEAD_ON_PAUSE to add the G-code M125 Pause and Park. */ -//#define ADVANCED_PAUSE_FEATURE +#define ADVANCED_PAUSE_FEATURE #if ENABLED(ADVANCED_PAUSE_FEATURE) #define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate. #define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract. @@ -2925,11 +2925,11 @@ //#define FILAMENT_CHANGE_RESUME_ON_INSERT // Automatically continue / load filament when runout sensor is triggered again. //#define PAUSE_REHEAT_FAST_RESUME // Reduce number of waits by not prompting again post-timeout before continuing. - //#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change. + #define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change. //#define HOME_BEFORE_FILAMENT_CHANGE // If needed, home before parking for filament change - //#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu. - //#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302) + #define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu. + #define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302) #define CONFIGURE_FILAMENT_CHANGE // Add M603 G-code and menu items. Requires ~1.3K bytes of flash. #endif @@ -3110,7 +3110,7 @@ #endif #if AXIS_IS_TMC_CONFIG(E0) - #define E0_CURRENT 800 + #define E0_CURRENT 900 #define E0_MICROSTEPS 16 #define E0_RSENSE 0.11 #define E0_CHAIN_POS -1 @@ -3283,7 +3283,7 @@ #define STEALTHCHOP_U #define STEALTHCHOP_V #define STEALTHCHOP_W - #define STEALTHCHOP_E + //#define STEALTHCHOP_E #endif /** @@ -3301,7 +3301,7 @@ * Define your own with: * { , , hysteresis_start[1..8] } */ - #define CHOPPER_TIMING CHOPPER_DEFAULT_12V // All axes (override below) + #define CHOPPER_TIMING CHOPPER_DEFAULT_24V // All axes (override below) //#define CHOPPER_TIMING_X CHOPPER_TIMING // For X Axes (override below) //#define CHOPPER_TIMING_X2 CHOPPER_TIMING_X //#define CHOPPER_TIMING_Y CHOPPER_TIMING // For Y Axes (override below) @@ -3445,7 +3445,7 @@ /** * Step on both rising and falling edge signals (as with a square wave). */ - //#define EDGE_STEPPING + #define EDGE_STEPPING /** * Enable M122 debugging command for TMC stepper drivers. @@ -4114,14 +4114,14 @@ * Host Prompt Support enables Marlin to use the host for user prompts so * filament runout and other processes can be managed from the host side. */ -//#define HOST_ACTION_COMMANDS +#define HOST_ACTION_COMMANDS #if ENABLED(HOST_ACTION_COMMANDS) //#define HOST_PAUSE_M76 // Tell the host to pause in response to M76 - //#define HOST_PROMPT_SUPPORT // Initiate host prompts to get user feedback + #define HOST_PROMPT_SUPPORT // Initiate host prompts to get user feedback #if ENABLED(HOST_PROMPT_SUPPORT) - //#define HOST_STATUS_NOTIFICATIONS // Send some status messages to the host as notifications + #define HOST_STATUS_NOTIFICATIONS // Send some status messages to the host as notifications #endif - //#define HOST_START_MENU_ITEM // Add a menu item that tells the host to start + #define HOST_START_MENU_ITEM // Add a menu item that tells the host to start //#define HOST_SHUTDOWN_MENU_ITEM // Add a menu item that tells the host to shut down #endif @@ -4489,12 +4489,12 @@ // // M42 - Set pin states // -//#define DIRECT_PIN_CONTROL +#define DIRECT_PIN_CONTROL // // M43 - display pin status, toggle pins, watch pins, watch endstops & toggle LED, test servo probe // -//#define PINS_DEBUGGING +#define PINS_DEBUGGING // Enable Tests that will run at startup and produce a report //#define MARLIN_TEST_BUILD