diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index df2860fd43..04a364c029 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -1904,6 +1904,9 @@
   #if ANY(Mini, MiniV2)
     #define NOZZLE_CLEAN_START_POINT {  45, 175, 0 }
     #define NOZZLE_CLEAN_END_POINT   { 115, 175, 0 }
+  #elif ENABLED(TazPro)
+    #define NOZZLE_CLEAN_START_POINT {{  -17, 95, 1 }, { 297, 95, 1 }}
+    #define NOZZLE_CLEAN_END_POINT   {{ -17, 25, 1 }, { 297, 25, 1 }}
   #else
     #define NOZZLE_CLEAN_START_POINT {  -17, 95, 1 }
     #define NOZZLE_CLEAN_END_POINT   { -17, 25, 1 }
@@ -1939,7 +1942,7 @@
 #elif ENABLED(Workhorse)
   #define WIPE_SEQUENCE_COMMANDS "M117 Hot end heating...\nM104 S170\nG28 O1\nM117 Wiping nozzle\nT0\nG1 X-17 Y25 Z10 F4000\nM109 R170\nG1 Z1\nM114\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 Z15\nM400\nM106 S255\nG0 X-10.0 Y-9.0M109 R160\nM107"
 #elif ENABLED(TazPro)
-  #define WIPE_SEQUENCE_COMMANDS "M117 Hot end heating...\nM104 S170 T0\nM104 S170 T1\nG28 O1\nM117 Wiping nozzle\nT0\nG1 X-17 Y25 Z10 F4000\nM109 R170 T0\nM109 R170 T1\nG1 Z1\nM114\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 X-17 Y25\nG1 X-17 Y95\nG1 Z15\nM400\nG0 X150 F5000\nT1\nG1 X297 Y25 Z10 F4000\nM109 R170 T0\nM109 R170 T1\nG1 Z1\nM114\nG1 X297 Y25\nG1 X297 Y95\nG1 X297 Y25\nG1 X297 Y95\nG1 X297 Y25\nG1 X297 Y95\nG1 X297 Y25\nG1 X297 Y95\nG1 X297 Y25\nG1 X297 Y95\nG1 X297 Y25\nG1 X297 Y95\nG1 Z15\nM400\nM106 S255 \nG0 X150 F5000\nT0\nM106 S255\nG0 X-10.0 Y-9.0M109 R160 T0\nM109 R160 T1\nM107"
+  //#define WIPE_SEQUENCE_COMMANDS "G1 X297 Y25 Z10 F4000\nM109 R170 T0\nM109 R170 T1\nG1 Z1\nM114\nG1 X297 Y25\nG1 X297 Y95\nG1 X297 Y25\nG1 X297 Y95\nG1 X297 Y25\nG1 X297 Y95\nG1 X297 Y25\nG1 X297 Y95\nG1 X297 Y25\nG1 X297 Y95\nG1 X297 Y25\nG1 X297 Y95\nG1 Z15\nM400\nM106 S255 \nG0 X150 F5000\nT0\nM106 S255\nG0 X-10.0 Y-9.0M109 R160 T0\nM109 R160 T1\nM107"
 #endif
 
 #endif
diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index 12612e6681..c18899063a 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -350,7 +350,7 @@
 #define HOTEND_IDLE_TIMEOUT
 #if ENABLED(HOTEND_IDLE_TIMEOUT)
   #define HOTEND_IDLE_TIMEOUT_SEC (15*60)    // (seconds) Time without extruder movement to trigger protection
-  #define HOTEND_IDLE_MIN_TRIGGER   160     // (°C) Minimum temperature to enable hotend protection
+  #define HOTEND_IDLE_MIN_TRIGGER   150     // (°C) Minimum temperature to enable hotend protection
   #define HOTEND_IDLE_NOZZLE_TARGET   0     // (°C) Safe temperature for the nozzle after timeout
   #define HOTEND_IDLE_BED_TARGET      0     // (°C) Safe temperature for the bed after timeout
 #endif