diff --git a/.circleci/config.yml b/.circleci/config.yml index 7d278d1275..4706bb5052 100644 --- a/.circleci/config.yml +++ b/.circleci/config.yml @@ -242,12 +242,12 @@ jobs: echo testing STM32F1 targets... export TEST_PLATFORM="-e STM32F1" restore_configs - echo use_example_configs STM32F10 - use_example_configs STM32F10 + echo use_example_configs STM32/STM32F10 + use_example_configs STM32/STM32F10 build_marlin_pio ./ ${TEST_PLATFORM} restore_configs - echo use_example_configs stm32f103ret6 - use_example_configs stm32f103ret6 + echo use_example_configs STM32/stm32f103ret6 + use_example_configs STM32/stm32f103ret6 build_marlin_pio ./ ${TEST_PLATFORM} restore_configs diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index 29ac040f82..1cdef3bcb8 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -110,8 +110,8 @@ Requires a sensor from above Melzi board users may only select ABL_BI for bilinear leveling */ -#define ABL_BI -//#define ABL_UBL +//#define ABL_BI +#define ABL_UBL //#define POWER_LOSS_RECOVERY //Large and does not fit with any other features on Melzi, or UBL on Atmega /* @@ -1954,7 +1954,9 @@ //========================= Unified Bed Leveling ============================ //=========================================================================== - #define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh + #if NONE(MachineCR10SPro, MachineCRX, MachineEnder5Plus, MachineCR10Max, OrigLCD) || ENABLED(GraphicLCD) + #define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh + #endif #define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle #define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500 @@ -1986,8 +1988,8 @@ #if ENABLED(AUTO_BED_LEVELING_3POINT) || ENABLED(AUTO_BED_LEVELING_UBL) #define MESH_INSET 15 -#if(DISABLED(MachineCR10Orig) && DISABLED(MachineEnder4)) -#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh +#if NONE(MachineCR10SPro, MachineCRX, MachineEnder5Plus, MachineCR10Max, MachineEnder4) || ENABLED(GraphicLCD) + #define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh #endif #if ENABLED(MachineEnder2) @@ -2004,6 +2006,13 @@ #define PROBE_PT_2_Y 180 #define PROBE_PT_3_X 150 #define PROBE_PT_3_Y 50 +#elif (ENABLED(MachineCRX)) + #define PROBE_PT_1_X 50 // Probing points for 3-Point leveling of the mesh + #define PROBE_PT_1_Y 250 + #define PROBE_PT_2_X 250 + #define PROBE_PT_2_Y 250 + #define PROBE_PT_3_X 250 + #define PROBE_PT_3_Y 50 #elif (ENABLED(MachineCR10Std)) #define PROBE_PT_1_X 50 // Probing points for 3-Point leveling of the mesh #define PROBE_PT_1_Y 270 @@ -2039,7 +2048,7 @@ * Add a bed leveling sub-menu for ABL or MBL. * Include a guided procedure if manual probing is enabled. */ -#if (DISABLED(ABL_EZABL) && DISABLED(ABL_NCSW) && DISABLED(ABL_BLTOUCH) &&DISABLED(OrigLA)) +#if DISABLED(ABL_EZABL, ABL_NCSW, ABL_BLTOUCH) #define LCD_BED_LEVELING #endif diff --git a/Marlin/src/HAL/HAL_LPC1768/usb_serial.cpp b/Marlin/src/HAL/HAL_LPC1768/usb_serial.cpp index d143bae709..c83931745a 100644 --- a/Marlin/src/HAL/HAL_LPC1768/usb_serial.cpp +++ b/Marlin/src/HAL/HAL_LPC1768/usb_serial.cpp @@ -1,13 +1,37 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + #ifdef TARGET_LPC1768 + #include "../../inc/MarlinConfigPre.h" #if ENABLED(EMERGENCY_PARSER) - #include "../../feature/emergency_parser.h" - EmergencyParser::State emergency_state; - bool CDC_RecvCallback(const char buffer) { - emergency_parser.update(emergency_state, buffer); - return true; - } -#endif // ENABLED(EMERGENCY_PARSER) +#include "../../feature/emergency_parser.h" +EmergencyParser::State emergency_state; +bool CDC_RecvCallback(const char buffer) { + emergency_parser.update(emergency_state, buffer); + return true; +} + +#endif // EMERGENCY_PARSER #endif // TARGET_LPC1768 diff --git a/Marlin/src/HAL/HAL_STM32/HAL_spi_STM32.cpp b/Marlin/src/HAL/HAL_STM32/HAL_spi_STM32.cpp index b2df7a16a7..b2e1ebc175 100644 --- a/Marlin/src/HAL/HAL_STM32/HAL_spi_STM32.cpp +++ b/Marlin/src/HAL/HAL_STM32/HAL_spi_STM32.cpp @@ -22,7 +22,6 @@ */ #if defined(ARDUINO_ARCH_STM32) && !defined(STM32GENERIC) - #include "../../inc/MarlinConfig.h" #include @@ -73,16 +72,22 @@ void spiInit(uint8_t spiRate) { // Use datarates Marlin uses uint32_t clock; switch (spiRate) { - case SPI_FULL_SPEED: clock = 20000000; break; // 13.9mhz=20000000 6.75mhz=10000000 3.38mhz=5000000 .833mhz=1000000 - case SPI_HALF_SPEED: clock = 5000000; break; - case SPI_QUARTER_SPEED: clock = 2500000; break; - case SPI_EIGHTH_SPEED: clock = 1250000; break; - case SPI_SPEED_5: clock = 625000; break; - case SPI_SPEED_6: clock = 300000; break; - default: - clock = 4000000; // Default from the SPI library + case SPI_FULL_SPEED: clock = 20000000; break; // 13.9mhz=20000000 6.75mhz=10000000 3.38mhz=5000000 .833mhz=1000000 + case SPI_HALF_SPEED: clock = 5000000; break; + case SPI_QUARTER_SPEED: clock = 2500000; break; + case SPI_EIGHTH_SPEED: clock = 1250000; break; + case SPI_SPEED_5: clock = 625000; break; + case SPI_SPEED_6: clock = 300000; break; + default: + clock = 4000000; // Default from the SPI library } spiConfig = SPISettings(clock, MSBFIRST, SPI_MODE0); + #if defined(MISO_PIN) && defined(SDSS) && defined(MOSI_PIN) && defined(SCK_PIN) + SPI.setMISO(MISO_PIN); + SPI.setSSEL(SDSS); + SPI.setMOSI(MOSI_PIN); + SPI.setSCLK(SCK_PIN); + #endif SPI.begin(); } diff --git a/Marlin/src/HAL/HAL_STM32_F4_F7/STM32F4/HAL_timers_STM32F4.cpp b/Marlin/src/HAL/HAL_STM32_F4_F7/STM32F4/HAL_timers_STM32F4.cpp index 45ea7fc984..26ea90e6d4 100644 --- a/Marlin/src/HAL/HAL_STM32_F4_F7/STM32F4/HAL_timers_STM32F4.cpp +++ b/Marlin/src/HAL/HAL_STM32_F4_F7/STM32F4/HAL_timers_STM32F4.cpp @@ -53,56 +53,40 @@ void HAL_timer_start(const uint8_t timer_num, const uint32_t frequency) { switch (timer_num) { case STEP_TIMER_NUM: // STEPPER TIMER TIM5 - use a 32bit timer - #ifdef STM32GENERIC - __HAL_RCC_TIM5_CLK_ENABLE(); - TimerHandle[timer_num].handle.Instance = TIM5; - TimerHandle[timer_num].handle.Init.Prescaler = step_prescaler; - TimerHandle[timer_num].handle.Init.CounterMode = TIM_COUNTERMODE_UP; - TimerHandle[timer_num].handle.Init.ClockDivision = TIM_CLOCKDIVISION_DIV1; - TimerHandle[timer_num].callback = (uint32_t)TC5_Handler; - #else - TimerHandle[timer_num].timer = TIM5; - TimerHandle[timer_num].irqHandle = TC5_Handler; - TimerHandleInit(&TimerHandle[timer_num], (((HAL_TIMER_RATE) / step_prescaler) / frequency) - 1, step_prescaler); - #endif + __HAL_RCC_TIM5_CLK_ENABLE(); + TimerHandle[timer_num].handle.Instance = TIM5; + TimerHandle[timer_num].handle.Init.Prescaler = step_prescaler; + TimerHandle[timer_num].handle.Init.CounterMode = TIM_COUNTERMODE_UP; + TimerHandle[timer_num].handle.Init.ClockDivision = TIM_CLOCKDIVISION_DIV1; + TimerHandle[timer_num].callback = (uint32_t)TC5_Handler; HAL_NVIC_SetPriority(STEP_TIMER_IRQ_ID, 1, 0); break; case TEMP_TIMER_NUM: // TEMP TIMER TIM7 - any available 16bit Timer (1 already used for PWM) - #ifdef STM32GENERIC - __HAL_RCC_TIM7_CLK_ENABLE(); - TimerHandle[timer_num].handle.Instance = TIM7; - TimerHandle[timer_num].handle.Init.Prescaler = temp_prescaler; - TimerHandle[timer_num].handle.Init.CounterMode = TIM_COUNTERMODE_UP; - TimerHandle[timer_num].handle.Init.ClockDivision = TIM_CLOCKDIVISION_DIV1; - TimerHandle[timer_num].callback = (uint32_t)TC7_Handler; - #else - TimerHandle[timer_num].timer = TIM7; - TimerHandle[timer_num].irqHandle = TC7_Handler; - TimerHandleInit(&TimerHandle[timer_num], (((HAL_TIMER_RATE) / temp_prescaler) / frequency) - 1, temp_prescaler); - #endif + __HAL_RCC_TIM7_CLK_ENABLE(); + TimerHandle[timer_num].handle.Instance = TIM7; + TimerHandle[timer_num].handle.Init.Prescaler = temp_prescaler; + TimerHandle[timer_num].handle.Init.CounterMode = TIM_COUNTERMODE_UP; + TimerHandle[timer_num].handle.Init.ClockDivision = TIM_CLOCKDIVISION_DIV1; + TimerHandle[timer_num].callback = (uint32_t)TC7_Handler; HAL_NVIC_SetPriority(TEMP_TIMER_IRQ_ID, 2, 0); break; } timers_initialized[timer_num] = true; } - #ifdef STM32GENERIC - TimerHandle[timer_num].handle.Init.Period = (((HAL_TIMER_RATE) / TimerHandle[timer_num].handle.Init.Prescaler) / frequency) - 1; - if (HAL_TIM_Base_Init(&TimerHandle[timer_num].handle) == HAL_OK) - HAL_TIM_Base_Start_IT(&TimerHandle[timer_num].handle); - #endif + TimerHandle[timer_num].handle.Init.Period = (((HAL_TIMER_RATE) / TimerHandle[timer_num].handle.Init.Prescaler) / frequency) - 1; + if (HAL_TIM_Base_Init(&TimerHandle[timer_num].handle) == HAL_OK) + HAL_TIM_Base_Start_IT(&TimerHandle[timer_num].handle); } -#ifdef STM32GENERIC - extern "C" void TIM5_IRQHandler() { - ((void(*)(void))TimerHandle[0].callback)(); - } - extern "C" void TIM7_IRQHandler() { - ((void(*)(void))TimerHandle[1].callback)(); - } -#endif +extern "C" void TIM5_IRQHandler() { + ((void(*)(void))TimerHandle[0].callback)(); +} +extern "C" void TIM7_IRQHandler() { + ((void(*)(void))TimerHandle[1].callback)(); +} void HAL_timer_enable_interrupt(const uint8_t timer_num) { switch (timer_num) { diff --git a/Marlin/src/HAL/HAL_STM32_F4_F7/STM32F7/HAL_timers_STM32F7.cpp b/Marlin/src/HAL/HAL_STM32_F4_F7/STM32F7/HAL_timers_STM32F7.cpp index 8da2fc0cfa..32697d7ccd 100644 --- a/Marlin/src/HAL/HAL_STM32_F4_F7/STM32F7/HAL_timers_STM32F7.cpp +++ b/Marlin/src/HAL/HAL_STM32_F4_F7/STM32F7/HAL_timers_STM32F7.cpp @@ -59,8 +59,9 @@ void HAL_timer_start(const uint8_t timer_num, const uint32_t frequency) { timerConfig[0].IRQ_Id = TIM5_IRQn; timerConfig[0].callback = (uint32_t)TC5_Handler; HAL_NVIC_SetPriority(timerConfig[0].IRQ_Id, 1, 0); - SET_OUTPUT(STEPPER_ENABLE_PIN); - WRITE(STEPPER_ENABLE_PIN); + #if PIN_EXISTS(STEPPER_ENABLE) + OUT_WRITE(STEPPER_ENABLE_PIN, HIGH); + #endif break; case TEMP_TIMER_NUM: //TEMP TIMER TIM7 // any available 16bit Timer (1 already used for PWM) diff --git a/Marlin/src/HAL/HAL_STM32_F4_F7/STM32F7/TMC2660.cpp b/Marlin/src/HAL/HAL_STM32_F4_F7/STM32F7/TMC2660.cpp index 2f60bf3546..698681e7f0 100644 --- a/Marlin/src/HAL/HAL_STM32_F4_F7/STM32F7/TMC2660.cpp +++ b/Marlin/src/HAL/HAL_STM32_F4_F7/STM32F7/TMC2660.cpp @@ -189,7 +189,6 @@ void TMC26XStepper::start() { pinMode(step_pin, OUTPUT); pinMode(dir_pin, OUTPUT); pinMode(cs_pin, OUTPUT); - //SET_OUTPUT(STEPPER_ENABLE_PIN); extDigitalWrite(step_pin, LOW); extDigitalWrite(dir_pin, LOW); extDigitalWrite(cs_pin, HIGH); diff --git a/Marlin/src/HAL/HAL_STM32_F4_F7/eeprom_emul.cpp b/Marlin/src/HAL/HAL_STM32_F4_F7/eeprom_emul.cpp index f8db99d3f6..1c9de1e212 100644 --- a/Marlin/src/HAL/HAL_STM32_F4_F7/eeprom_emul.cpp +++ b/Marlin/src/HAL/HAL_STM32_F4_F7/eeprom_emul.cpp @@ -86,6 +86,8 @@ uint16_t EE_Initialize(void) { pEraseInit.NbSectors = 1; pEraseInit.VoltageRange = VOLTAGE_RANGE; + HAL_StatusTypeDef FlashStatus; // = HAL_OK + /* Check for invalid header states and repair if necessary */ uint32_t SectorError; switch (PageStatus0) { @@ -135,7 +137,7 @@ uint16_t EE_Initialize(void) { } } /* Mark Page0 as valid */ - HAL_StatusTypeDef FlashStatus = HAL_FLASH_Program(TYPEPROGRAM_HALFWORD, PAGE0_BASE_ADDRESS, VALID_PAGE); + FlashStatus = HAL_FLASH_Program(TYPEPROGRAM_HALFWORD, PAGE0_BASE_ADDRESS, VALID_PAGE); /* If program operation was failed, a Flash error code is returned */ if (FlashStatus != HAL_OK) return FlashStatus; pEraseInit.Sector = PAGE1_ID; diff --git a/Marlin/src/Marlin.cpp b/Marlin/src/Marlin.cpp index ebcb0dda06..a548fc43a2 100644 --- a/Marlin/src/Marlin.cpp +++ b/Marlin/src/Marlin.cpp @@ -65,7 +65,7 @@ #include "feature/host_actions.h" #endif -#if HAS_BUZZER && DISABLED(LCD_USE_I2C_BUZZER) +#if USE_BEEPER #include "libs/buzzer.h" #endif @@ -702,7 +702,7 @@ void idle( print_job_timer.tick(); #endif - #if HAS_BUZZER && DISABLED(LCD_USE_I2C_BUZZER) && DISABLED(PCA9632_BUZZER) + #if USE_BEEPER buzzer.tick(); #endif @@ -886,6 +886,10 @@ void setup() { runout.setup(); #endif + #if ENABLED(POWER_LOSS_RECOVERY) + recovery.setup(); + #endif + setup_killpin(); #if HAS_TMC220x diff --git a/Marlin/src/core/boards.h b/Marlin/src/core/boards.h index 7d02566247..181e3ffe7a 100644 --- a/Marlin/src/core/boards.h +++ b/Marlin/src/core/boards.h @@ -113,24 +113,25 @@ #define BOARD_CNCONTROLS_11 1300 // Cartesio CN Controls V11 #define BOARD_CNCONTROLS_12 1301 // Cartesio CN Controls V12 -#define BOARD_CHEAPTRONIC 1302 // Cheaptronic v1.0 -#define BOARD_CHEAPTRONIC_V2 1303 // Cheaptronic v2.0 -#define BOARD_MIGHTYBOARD_REVE 1304 // Makerbot Mightyboard Revision E -#define BOARD_MEGATRONICS 1305 // Megatronics -#define BOARD_MEGATRONICS_2 1306 // Megatronics v2.0 -#define BOARD_MEGATRONICS_3 1307 // Megatronics v3.0 -#define BOARD_MEGATRONICS_31 1308 // Megatronics v3.1 -#define BOARD_MEGATRONICS_32 1309 // Megatronics v3.2 -#define BOARD_ELEFU_3 1310 // Elefu Ra Board (v3) -#define BOARD_LEAPFROG 1311 // Leapfrog -#define BOARD_MEGACONTROLLER 1312 // Mega controller -#define BOARD_GT2560_REV_A 1313 // Geeetech GT2560 Rev. A -#define BOARD_GT2560_REV_A_PLUS 1314 // Geeetech GT2560 Rev. A+ (with auto level probe) -#define BOARD_GT2560_V3 1315 // Geeetech GT2560 Rev B for A10(M/D) -#define BOARD_GT2560_V3_MC2 1316 // Geeetech GT2560 Rev B for Mecreator2 -#define BOARD_GT2560_V3_A20 1317 // Geeetech GT2560 Rev B for A20(M/D) -#define BOARD_EINSTART_S 1318 // Einstart retrofit -#define BOARD_WANHAO_ONEPLUS 1319 // Wanhao 0ne+ i3 Mini +#define BOARD_CNCONTROLS_15 1302 // Cartesio CN Controls V15 +#define BOARD_CHEAPTRONIC 1303 // Cheaptronic v1.0 +#define BOARD_CHEAPTRONIC_V2 1304 // Cheaptronic v2.0 +#define BOARD_MIGHTYBOARD_REVE 1305 // Makerbot Mightyboard Revision E +#define BOARD_MEGATRONICS 1306 // Megatronics +#define BOARD_MEGATRONICS_2 1307 // Megatronics v2.0 +#define BOARD_MEGATRONICS_3 1308 // Megatronics v3.0 +#define BOARD_MEGATRONICS_31 1309 // Megatronics v3.1 +#define BOARD_MEGATRONICS_32 1310 // Megatronics v3.2 +#define BOARD_ELEFU_3 1311 // Elefu Ra Board (v3) +#define BOARD_LEAPFROG 1312 // Leapfrog +#define BOARD_MEGACONTROLLER 1313 // Mega controller +#define BOARD_GT2560_REV_A 1314 // Geeetech GT2560 Rev. A +#define BOARD_GT2560_REV_A_PLUS 1315 // Geeetech GT2560 Rev. A+ (with auto level probe) +#define BOARD_GT2560_V3 1316 // Geeetech GT2560 Rev B for A10(M/D) +#define BOARD_GT2560_V3_MC2 1317 // Geeetech GT2560 Rev B for Mecreator2 +#define BOARD_GT2560_V3_A20 1318 // Geeetech GT2560 Rev B for A20(M/D) +#define BOARD_EINSTART_S 1319 // Einstart retrofit +#define BOARD_WANHAO_ONEPLUS 1320 // Wanhao 0ne+ i3 Mini // // ATmega1281, ATmega2561 @@ -290,6 +291,7 @@ #define BOARD_BLACK_STM32F407ZE 4205 // BLACK_STM32F407ZE #define BOARD_STEVAL 4206 // STEVAL-3DP001V1 3D PRINTER BOARD #define BOARD_BIGTREE_SKR_PRO_V1_1 4207 // BigTreeTech SKR Pro v1.1 (STM32F407ZG) +#define BOARD_BIGTREE_BTT002_V1_0 4208 // BigTreeTech BTT002 v1.0 (STM32F407VE) // // ARM Cortex M7 diff --git a/Marlin/src/feature/bedlevel/ubl/ubl_G29.cpp b/Marlin/src/feature/bedlevel/ubl/ubl_G29.cpp index 568f766150..6b6233f826 100644 --- a/Marlin/src/feature/bedlevel/ubl/ubl_G29.cpp +++ b/Marlin/src/feature/bedlevel/ubl/ubl_G29.cpp @@ -752,16 +752,15 @@ save_ubl_active_state_and_disable(); // No bed level correction so only raw data is obtained DEPLOY_PROBE(); - uint8_t count = GRID_MAX_POINTS, current = 1; + uint8_t count = GRID_MAX_POINTS; do { - current = (GRID_MAX_POINTS) - count + 1; - if (do_ubl_mesh_map) display_map(g29_map_type); - SERIAL_ECHOLNPAIR("\nProbing mesh point ", int(current), "/", int(GRID_MAX_POINTS), ".\n"); + const int current = (GRID_MAX_POINTS) - count + 1; + SERIAL_ECHOLNPAIR("\nProbing mesh point ", current, "/", int(GRID_MAX_POINTS), ".\n"); #if HAS_DISPLAY - ui.status_printf_P(0, PSTR(MSG_PROBING_MESH " %i/%i"), int(current), int(GRID_MAX_POINTS)); + ui.status_printf_P(0, PSTR(MSG_PROBING_MESH " %i/%i"), current, int(GRID_MAX_POINTS)); #endif #if HAS_LCD_MENU @@ -1500,8 +1499,7 @@ DEBUG_ECHO_F(rx, 7); DEBUG_CHAR(','); DEBUG_ECHO_F(ry, 7); - DEBUG_ECHOPGM(") logical: "); - DEBUG_CHAR('('); + DEBUG_ECHOPGM(") logical: ("); DEBUG_ECHO_F(LOGICAL_X_POSITION(rx), 7); DEBUG_CHAR(','); DEBUG_ECHO_F(LOGICAL_Y_POSITION(ry), 7); diff --git a/Marlin/src/feature/host_actions.cpp b/Marlin/src/feature/host_actions.cpp index 5ffa6adb84..b39b0fbc3c 100644 --- a/Marlin/src/feature/host_actions.cpp +++ b/Marlin/src/feature/host_actions.cpp @@ -37,10 +37,6 @@ #include "runout.h" #endif -#if ENABLED(EXTENSIBLE_UI) - #include "../lcd/extensible_ui/ui_api.h" -#endif - void host_action(const char * const pstr, const bool eol) { SERIAL_ECHOPGM("//action:"); serialprintPGM(pstr); @@ -92,7 +88,6 @@ void host_action(const char * const pstr, const bool eol) { void host_action_prompt_show() { host_action_prompt(PSTR("show")); } void host_prompt_do(const PromptReason reason, const char * const pstr, const char * const pbtn/*=nullptr*/) { host_prompt_reason = reason; - host_action_prompt_end(); host_action_prompt_begin(pstr); if (pbtn) host_action_prompt_button(pbtn); diff --git a/Marlin/src/feature/leds/pca9632.cpp b/Marlin/src/feature/leds/pca9632.cpp index 6f69bd31ef..87589a9bcd 100644 --- a/Marlin/src/feature/leds/pca9632.cpp +++ b/Marlin/src/feature/leds/pca9632.cpp @@ -137,13 +137,15 @@ void pca9632_set_led_color(const LEDColor &color) { } #if ENABLED(PCA9632_BUZZER) - void pca9632_buzz(uint16_t const f, uint16_t d) { - UNUSED(f); UNUSED(d); + + void pca9632_buzz(const long duration, const uint16_t freq) { + UNUSED(duration); UNUSED(freq); uint8_t data[] = PCA9632_BUZZER_DATA; Wire.beginTransmission(I2C_ADDRESS(PCA9632_ADDRESS)); Wire.write(data, sizeof(data)); Wire.endTransmission(); } -#endif + +#endif // PCA9632_BUZZER #endif // PCA9632 diff --git a/Marlin/src/feature/leds/pca9632.h b/Marlin/src/feature/leds/pca9632.h index 023e451979..2abdf7c7af 100644 --- a/Marlin/src/feature/leds/pca9632.h +++ b/Marlin/src/feature/leds/pca9632.h @@ -32,5 +32,6 @@ typedef LEDColor LEDColor; void pca9632_set_led_color(const LEDColor &color); #if ENABLED(PCA9632_BUZZER) - void pca9632_buzz(uint16_t const, uint16_t); + #include + void pca9632_buzz(const long, const uint16_t); #endif diff --git a/Marlin/src/feature/pause.cpp b/Marlin/src/feature/pause.cpp index 93ec782027..aca275b39d 100644 --- a/Marlin/src/feature/pause.cpp +++ b/Marlin/src/feature/pause.cpp @@ -188,8 +188,8 @@ bool load_filament(const float &slow_load_length/*=0*/, const float &fast_load_l host_action_prompt_show(); #endif #if ENABLED(EXTENSIBLE_UI) - ExtUI::onUserConfirmRequired("Load Filament"); - #endif + ExtUI::onStatusChanged(PSTR("Load Filament")); + #endif while (wait_for_user) { #if HAS_BUZZER filament_change_beep(max_beep_count); @@ -242,6 +242,9 @@ bool load_filament(const float &slow_load_length/*=0*/, const float &fast_load_l #if ENABLED(HOST_PROMPT_SUPPORT) host_prompt_do(PROMPT_USER_CONTINUE, PSTR("Continuous Purge Running..."), PSTR("Continue")); #endif + #if ENABLED(EXTENSIBLE_UI) + ExtUI::onStatusChanged(PSTR("Continuous Purge Running...")); + #endif for (float purge_count = purge_length; purge_count > 0 && wait_for_user; --purge_count) do_pause_e_move(1, ADVANCED_PAUSE_PURGE_FEEDRATE); wait_for_user = false; @@ -514,16 +517,15 @@ void wait_for_confirmation(const bool is_reload/*=false*/, const int8_t max_beep extruder_duplication_enabled = false; #endif - #if ENABLED(EXTENSIBLE_UI) - ExtUI::onUserConfirmRequired("Paused for User"); - #endif - // Wait for filament insert by user and press button KEEPALIVE_STATE(PAUSED_FOR_USER); wait_for_user = true; // LCD click or M108 will clear this #if ENABLED(HOST_PROMPT_SUPPORT) host_prompt_do(PROMPT_USER_CONTINUE, PSTR("Nozzle Parked"), PSTR("Continue")); #endif + #if ENABLED(EXTENSIBLE_UI) + ExtUI::onStatusChanged(PSTR("Nozzle Parked")); + #endif while (wait_for_user) { #if HAS_BUZZER filament_change_beep(max_beep_count); @@ -545,6 +547,10 @@ void wait_for_confirmation(const bool is_reload/*=false*/, const int8_t max_beep host_prompt_do(PROMPT_USER_CONTINUE, PSTR("HeaterTimeout"), PSTR("Reheat")); #endif + #if ENABLED(EXTENSIBLE_UI) + ExtUI::onStatusChanged(PSTR("HeaterTimeout")); + #endif + // Wait for LCD click or M108 while (wait_for_user) idle(true); diff --git a/Marlin/src/feature/power_loss_recovery.h b/Marlin/src/feature/power_loss_recovery.h index d58285e563..34322243fd 100644 --- a/Marlin/src/feature/power_loss_recovery.h +++ b/Marlin/src/feature/power_loss_recovery.h @@ -26,12 +26,16 @@ */ #include "../sd/cardreader.h" -#include "../inc/MarlinConfigPre.h" +#include "../inc/MarlinConfig.h" #if ENABLED(MIXING_EXTRUDER) #include "../feature/mixing.h" #endif +#if !defined(POWER_LOSS_STATE) && PIN_EXISTS(POWER_LOSS) + #define POWER_LOSS_STATE HIGH +#endif + //#define DEBUG_POWER_LOSS_RECOVERY //#define SAVE_EACH_CMD_MODE //#define SAVE_INFO_INTERVAL_MS 0 @@ -110,6 +114,20 @@ class PrintJobRecovery { static void init(); + static inline void setup() { + #if PIN_EXISTS(POWER_LOSS) + #if ENABLED(POWER_LOSS_PULL) + #if POWER_LOSS_STATE == LOW + SET_INPUT_PULLUP(POWER_LOSS_PIN); + #else + SET_INPUT_PULLDOWN(POWER_LOSS_PIN); + #endif + #else + SET_INPUT(POWER_LOSS_PIN); + #endif + #endif + } + static bool enabled; static void enable(const bool onoff); static void changed(); diff --git a/Marlin/src/feature/prusa_MMU2/mmu2.cpp b/Marlin/src/feature/prusa_MMU2/mmu2.cpp index 3eda08c820..12f84af3e8 100644 --- a/Marlin/src/feature/prusa_MMU2/mmu2.cpp +++ b/Marlin/src/feature/prusa_MMU2/mmu2.cpp @@ -42,6 +42,10 @@ MMU2 mmu2; #include "../../feature/host_actions.h" #endif +#if ENABLED(EXTENSIBLE_UI) + #include "../../lcd/extensible_ui/ui_api.h" +#endif + #define DEBUG_OUT ENABLED(MMU2_DEBUG) #include "../../core/debug_out.h" @@ -707,13 +711,13 @@ void MMU2::filament_runout() { if (recover) { LCD_MESSAGEPGM(MSG_MMU2_EJECT_RECOVER); BUZZ(200, 404); - #if ENABLED(EXTENSIBLE_UI) - ExtUI::onUserConfirmRequired("MMU2 Eject Recover"); - #endif wait_for_user = true; #if ENABLED(HOST_PROMPT_SUPPORT) host_prompt_do(PROMPT_USER_CONTINUE, PSTR("MMU2 Eject Recover"), PSTR("Continue")); #endif + #if ENABLED(EXTENSIBLE_UI) + ExtUI::onStatusChanged(PSTR("MMU2 Eject Recover")); + #endif while (wait_for_user) idle(); BUZZ(200, 404); BUZZ(200, 404); diff --git a/Marlin/src/gcode/calibrate/G28.cpp b/Marlin/src/gcode/calibrate/G28.cpp index f831fce281..d936809051 100644 --- a/Marlin/src/gcode/calibrate/G28.cpp +++ b/Marlin/src/gcode/calibrate/G28.cpp @@ -212,7 +212,6 @@ void GcodeSuite::G28(const bool always_home_all) { return; } - ui.set_status_P(PSTR("Homing...")); // Wait for planner moves to finish! planner.synchronize(); diff --git a/Marlin/src/gcode/config/M43.cpp b/Marlin/src/gcode/config/M43.cpp index 1212abf8b7..3f3c48150a 100644 --- a/Marlin/src/gcode/config/M43.cpp +++ b/Marlin/src/gcode/config/M43.cpp @@ -328,15 +328,14 @@ void GcodeSuite::M43() { } #if HAS_RESUME_CONTINUE - #if ENABLED(EXTENSIBLE_UI) - ExtUI::onUserConfirmRequired("M43 Called"); - #endif - KEEPALIVE_STATE(PAUSED_FOR_USER); wait_for_user = true; #if ENABLED(HOST_PROMPT_SUPPORT) host_prompt_do(PROMPT_USER_CONTINUE, PSTR("M43 Wait Called"), PSTR("Continue")); #endif + #if ENABLED(EXTENSIBLE_UI) + ExtUI::onStatusChanged(PSTR("M43 Wait Called")); + #endif #endif for (;;) { diff --git a/Marlin/src/gcode/lcd/M0_M1.cpp b/Marlin/src/gcode/lcd/M0_M1.cpp index 3bbf329918..67f634ce83 100644 --- a/Marlin/src/gcode/lcd/M0_M1.cpp +++ b/Marlin/src/gcode/lcd/M0_M1.cpp @@ -97,6 +97,9 @@ void GcodeSuite::M0_M1() { #if ENABLED(HOST_PROMPT_SUPPORT) host_prompt_do(PROMPT_USER_CONTINUE, PSTR("M0/1 Break Called"), PSTR("Continue")); #endif + #if ENABLED(EXTENSIBLE_UI) + ExtUI::onStatusChanged(PSTR("M0/1 Break Called")); + #endif if (ms > 0) { ms += millis(); // wait until this time for a click diff --git a/Marlin/src/inc/Conditionals_LCD.h b/Marlin/src/inc/Conditionals_LCD.h index 411e2fe834..0d719e844b 100644 --- a/Marlin/src/inc/Conditionals_LCD.h +++ b/Marlin/src/inc/Conditionals_LCD.h @@ -384,7 +384,14 @@ /** * Default LCD contrast for Graphical LCD displays */ -#define HAS_LCD_CONTRAST (HAS_GRAPHICAL_LCD && defined(DEFAULT_LCD_CONTRAST)) +#define HAS_LCD_CONTRAST ( \ + ENABLED(MAKRPANEL) \ + || ENABLED(CARTESIO_UI) \ + || ENABLED(VIKI2) \ + || ENABLED(AZSMZ_12864) \ + || ENABLED(miniVIKI) \ + || ENABLED(ELB_FULL_GRAPHIC_CONTROLLER) \ +) #if HAS_LCD_CONTRAST #ifndef LCD_CONTRAST_MIN #define LCD_CONTRAST_MIN 0 diff --git a/Marlin/src/inc/Conditionals_post.h b/Marlin/src/inc/Conditionals_post.h index f3d850aea1..937db9ee6a 100644 --- a/Marlin/src/inc/Conditionals_post.h +++ b/Marlin/src/inc/Conditionals_post.h @@ -1048,7 +1048,8 @@ #define HAS_KILL (PIN_EXISTS(KILL)) #define HAS_SUICIDE (PIN_EXISTS(SUICIDE)) #define HAS_PHOTOGRAPH (PIN_EXISTS(PHOTOGRAPH)) -#define HAS_BUZZER (PIN_EXISTS(BEEPER) || ENABLED(LCD_USE_I2C_BUZZER) || ENABLED(PCA9632_BUZZER)) +#define HAS_BUZZER (PIN_EXISTS(BEEPER) || EITHER(LCD_USE_I2C_BUZZER, PCA9632_BUZZER)) +#define USE_BEEPER (HAS_BUZZER && DISABLED(LCD_USE_I2C_BUZZER, PCA9632_BUZZER)) #define HAS_CASE_LIGHT (PIN_EXISTS(CASE_LIGHT) && ENABLED(CASE_LIGHT_ENABLE)) // Digital control @@ -1570,7 +1571,7 @@ #ifndef LCD_FEEDBACK_FREQUENCY_DURATION_MS #define LCD_FEEDBACK_FREQUENCY_DURATION_MS 100 #endif -#else +#elif HAS_BUZZER #ifndef LCD_FEEDBACK_FREQUENCY_HZ #define LCD_FEEDBACK_FREQUENCY_HZ 5000 #endif diff --git a/Marlin/src/lcd/HD44780/lcdprint_hd44780.cpp b/Marlin/src/lcd/HD44780/lcdprint_hd44780.cpp index 08cc468d20..781e76d379 100644 --- a/Marlin/src/lcd/HD44780/lcdprint_hd44780.cpp +++ b/Marlin/src/lcd/HD44780/lcdprint_hd44780.cpp @@ -877,7 +877,7 @@ static int pf_bsearch_cb_comp_hd4map_pgm(void *userdata, size_t idx, void * data return hd44780_charmap_compare(&localval, (hd44780_charmap_t *)data_pin); } -void lcd_moveto(const uint8_t col, const uint8_t row) { lcd.setCursor(col, row); } +void lcd_moveto(const lcd_uint_t col, const lcd_uint_t row) { lcd.setCursor(col, row); } void lcd_put_int(const int i) { lcd.print(i); } diff --git a/Marlin/src/lcd/HD44780/ultralcd_HD44780.cpp b/Marlin/src/lcd/HD44780/ultralcd_HD44780.cpp index 65f50efa24..54eb614cb4 100644 --- a/Marlin/src/lcd/HD44780/ultralcd_HD44780.cpp +++ b/Marlin/src/lcd/HD44780/ultralcd_HD44780.cpp @@ -360,18 +360,45 @@ void MarlinUI::init_lcd() { lcd.clear(); } +bool MarlinUI::detected() { + return true + #if EITHER(LCD_I2C_TYPE_MCP23017, LCD_I2C_TYPE_MCP23008) && defined(DETECT_DEVICE) + && lcd.LcdDetected() == 1 + #endif + ; +} + +#if HAS_SLOW_BUTTONS + uint8_t MarlinUI::read_slow_buttons() { + #if ENABLED(LCD_I2C_TYPE_MCP23017) + // Reading these buttons this is likely to be too slow to call inside interrupt context + // so they are called during normal lcd_update + uint8_t slow_bits = lcd.readButtons() + #if !BUTTON_EXISTS(ENC) + << B_I2C_BTN_OFFSET + #endif + ; + #if ENABLED(LCD_I2C_VIKI) + if ((slow_bits & (B_MI | B_RI)) && PENDING(millis(), next_button_update_ms)) // LCD clicked + slow_bits &= ~(B_MI | B_RI); // Disable LCD clicked buttons if screen is updated + #endif // LCD_I2C_VIKI + return slow_bits; + #endif // LCD_I2C_TYPE_MCP23017 + } +#endif + void MarlinUI::clear_lcd() { lcd.clear(); } #if ENABLED(SHOW_BOOTSCREEN) - void lcd_erase_line(const int16_t line) { + void lcd_erase_line(const lcd_uint_t line) { lcd_moveto(0, line); for (uint8_t i = LCD_WIDTH + 1; --i;) lcd_put_wchar(' '); } // Scroll the PSTR 'text' in a 'len' wide field for 'time' milliseconds at position col,line - void lcd_scroll(const uint8_t col, const uint8_t line, PGM_P const text, const uint8_t len, const int16_t time) { + void lcd_scroll(const lcd_uint_t col, const lcd_uint_t line, PGM_P const text, const uint8_t len, const int16_t time) { uint8_t slen = utf8_strlen_P(text); if (slen < len) { // Fits into, @@ -1031,9 +1058,9 @@ void MarlinUI::draw_status_screen() { if (value != nullptr) { lcd_put_wchar(':'); int len = utf8_strlen(value); - const uint8_t valrow = (utf8_strlen_P(pstr) + 1 + len + 1) > (LCD_WIDTH - 2) ? 2 : 1; // Value on the next row if it won't fit - lcd_moveto((LCD_WIDTH - 1) - (len + 1), valrow); // Right-justified, padded by spaces - lcd_put_wchar(' '); // Overwrite char if value gets shorter + const lcd_uint_t valrow = (utf8_strlen_P(pstr) + 1 + len + 1) > (LCD_WIDTH - 2) ? 2 : 1; // Value on the next row if it won't fit + lcd_moveto((LCD_WIDTH - 1) - (len + 1), valrow); // Right-justified, padded by spaces + lcd_put_wchar(' '); // Overwrite char if value gets shorter lcd_put_u8str(value); } } @@ -1063,7 +1090,7 @@ void MarlinUI::draw_status_screen() { #if ENABLED(LCD_HAS_STATUS_INDICATORS) - static void MarlinUI::update_indicators() { + void MarlinUI::update_indicators() { // Set the LEDS - referred to as backlights by the LiquidTWI2 library static uint8_t ledsprev = 0; uint8_t leds = 0; @@ -1144,9 +1171,9 @@ void MarlinUI::draw_status_screen() { } custom_char; typedef struct { - uint8_t column, row, - x_pixel_offset, y_pixel_offset, - x_pixel_mask; + lcd_uint_t column, row, + x_pixel_offset, y_pixel_offset; + uint8_t x_pixel_mask; } coordinate; void add_edges_to_custom_char(custom_char &custom, const coordinate &ul, const coordinate &lr, const coordinate &brc, const uint8_t cell_location); @@ -1174,16 +1201,16 @@ void MarlinUI::draw_status_screen() { return ret_val; } - inline coordinate pixel_location(const uint8_t x, const uint8_t y) { return pixel_location((int16_t)x, (int16_t)y); } + inline coordinate pixel_location(const lcd_uint_t x, const lcd_uint_t y) { return pixel_location((int16_t)x, (int16_t)y); } - void prep_and_put_map_char(custom_char &chrdata, const coordinate &ul, const coordinate &lr, const coordinate &brc, const uint8_t cl, const char c, const uint8_t x, const uint8_t y) { + void prep_and_put_map_char(custom_char &chrdata, const coordinate &ul, const coordinate &lr, const coordinate &brc, const uint8_t cl, const char c, const lcd_uint_t x, const lcd_uint_t y) { add_edges_to_custom_char(chrdata, ul, lr, brc, cl); lcd.createChar(c, (uint8_t*)&chrdata); lcd_moveto(x, y); lcd_put_wchar(c); } - void MarlinUI::ubl_plot(const uint8_t x, const uint8_t inverted_y) { + void MarlinUI::ubl_plot(const uint8_t x_plot, const uint8_t y_plot) { #if LCD_WIDTH >= 20 #define _LCD_W_POS 12 @@ -1209,10 +1236,10 @@ void MarlinUI::draw_status_screen() { * Show X and Y positions */ _XLABEL(_PLOT_X, 0); - lcd_put_u8str(ftostr52(LOGICAL_X_POSITION(pgm_read_float(&ubl._mesh_index_to_xpos[x])))); + lcd_put_u8str(ftostr52(LOGICAL_X_POSITION(pgm_read_float(&ubl._mesh_index_to_xpos[x_plot])))); _YLABEL(_LCD_W_POS, 0); - lcd_put_u8str(ftostr52(LOGICAL_Y_POSITION(pgm_read_float(&ubl._mesh_index_to_ypos[inverted_y])))); + lcd_put_u8str(ftostr52(LOGICAL_Y_POSITION(pgm_read_float(&ubl._mesh_index_to_ypos[y_plot])))); lcd_moveto(_PLOT_X, 0); @@ -1220,13 +1247,13 @@ void MarlinUI::draw_status_screen() { coordinate upper_left, lower_right, bottom_right_corner; custom_char new_char; - uint8_t i, j, k, l, m, n, n_rows, n_cols, y, - bottom_line, right_edge, - x_map_pixels, y_map_pixels, - pixels_per_x_mesh_pnt, pixels_per_y_mesh_pnt, - suppress_x_offset = 0, suppress_y_offset = 0; + uint8_t i, n, n_rows, n_cols; + lcd_uint_t j, k, l, m, bottom_line, right_edge, + x_map_pixels, y_map_pixels, + pixels_per_x_mesh_pnt, pixels_per_y_mesh_pnt, + suppress_x_offset = 0, suppress_y_offset = 0; - y = GRID_MAX_POINTS_Y - inverted_y - 1; + const uint8_t y_plot_inv = (GRID_MAX_POINTS_Y - 1) - y_plot; upper_left.column = 0; upper_left.row = 0; @@ -1310,12 +1337,12 @@ void MarlinUI::draw_status_screen() { new_char.custom_char_bits[j] = (uint8_t)_BV(i); // Char #3 is used for the box right edge lcd.createChar(CHAR_EDGE_R, (uint8_t*)&new_char); - i = x * pixels_per_x_mesh_pnt - suppress_x_offset; - j = y * pixels_per_y_mesh_pnt - suppress_y_offset; + i = x_plot * pixels_per_x_mesh_pnt - suppress_x_offset; + j = y_plot_inv * pixels_per_y_mesh_pnt - suppress_y_offset; upper_left = pixel_location(i, j); - k = (x + 1) * pixels_per_x_mesh_pnt - 1 - suppress_x_offset; - l = (y + 1) * pixels_per_y_mesh_pnt - 1 - suppress_y_offset; + k = (x_plot + 1) * pixels_per_x_mesh_pnt - 1 - suppress_x_offset; + l = (y_plot_inv + 1) * pixels_per_y_mesh_pnt - 1 - suppress_y_offset; lower_right = pixel_location(k, l); bottom_right_corner = pixel_location(x_map_pixels, y_map_pixels); @@ -1327,7 +1354,7 @@ void MarlinUI::draw_status_screen() { */ clear_custom_char(&new_char); - const uint8_t ypix = _MIN(upper_left.y_pixel_offset + pixels_per_y_mesh_pnt, HD44780_CHAR_HEIGHT); + const lcd_uint_t ypix = _MIN(upper_left.y_pixel_offset + pixels_per_y_mesh_pnt, HD44780_CHAR_HEIGHT); for (j = upper_left.y_pixel_offset; j < ypix; j++) { i = upper_left.x_pixel_mask; for (k = 0; k < pixels_per_x_mesh_pnt; k++) { @@ -1400,9 +1427,9 @@ void MarlinUI::draw_status_screen() { */ lcd_moveto(_LCD_W_POS, 0); lcd_put_wchar('('); - lcd_put_u8str(ui8tostr3(x)); + lcd_put_u8str(ui8tostr3(x_plot)); lcd_put_wchar(','); - lcd_put_u8str(ui8tostr3(inverted_y)); + lcd_put_u8str(ui8tostr3(y_plot)); lcd_put_wchar(')'); #if LCD_HEIGHT <= 3 // 16x2 or 20x2 display @@ -1411,8 +1438,8 @@ void MarlinUI::draw_status_screen() { * Print Z values */ _ZLABEL(_LCD_W_POS, 1); - if (!isnan(ubl.z_values[x][inverted_y])) - lcd_put_u8str(ftostr43sign(ubl.z_values[x][inverted_y])); + if (!isnan(ubl.z_values[x_plot][y_plot])) + lcd_put_u8str(ftostr43sign(ubl.z_values[x_plot][y_plot])); else lcd_put_u8str_P(PSTR(" -----")); @@ -1422,16 +1449,16 @@ void MarlinUI::draw_status_screen() { * Show all values at right of screen */ _XLABEL(_LCD_W_POS, 1); - lcd_put_u8str(ftostr52(LOGICAL_X_POSITION(pgm_read_float(&ubl._mesh_index_to_xpos[x])))); + lcd_put_u8str(ftostr52(LOGICAL_X_POSITION(pgm_read_float(&ubl._mesh_index_to_xpos[x_plot])))); _YLABEL(_LCD_W_POS, 2); - lcd_put_u8str(ftostr52(LOGICAL_Y_POSITION(pgm_read_float(&ubl._mesh_index_to_ypos[inverted_y])))); + lcd_put_u8str(ftostr52(LOGICAL_Y_POSITION(pgm_read_float(&ubl._mesh_index_to_ypos[y_plot])))); /** * Show the location value */ _ZLABEL(_LCD_W_POS, 3); - if (!isnan(ubl.z_values[x][inverted_y])) - lcd_put_u8str(ftostr43sign(ubl.z_values[x][inverted_y])); + if (!isnan(ubl.z_values[x_plot][y_plot])) + lcd_put_u8str(ftostr43sign(ubl.z_values[x_plot][y_plot])); else lcd_put_u8str_P(PSTR(" -----")); diff --git a/Marlin/src/lcd/dogm/lcdprint_u8g.cpp b/Marlin/src/lcd/dogm/lcdprint_u8g.cpp index d46eb85903..c9ff96547b 100644 --- a/Marlin/src/lcd/dogm/lcdprint_u8g.cpp +++ b/Marlin/src/lcd/dogm/lcdprint_u8g.cpp @@ -22,7 +22,7 @@ int lcd_glyph_height(void) { return u8g_GetFontBBXHeight(u8g.getU8g()); } -void lcd_moveto(const uint8_t col, const uint8_t row) { u8g.setPrintPos(col, row); } +void lcd_moveto(const lcd_uint_t col, const lcd_uint_t row) { u8g.setPrintPos(col, row); } void lcd_put_int(const int i) { u8g.print(i); } @@ -33,26 +33,22 @@ int lcd_put_wchar_max(wchar_t c, pixel_len_t max_length) { u8g.print((char)c); return u8g_GetFontBBXWidth(u8g.getU8g()); } - unsigned int x = u8g.getPrintCol(), - y = u8g.getPrintRow(), - ret = uxg_DrawWchar(u8g.getU8g(), x, y, c, max_length); + u8g_uint_t x = u8g.getPrintCol(), y = u8g.getPrintRow(), + ret = uxg_DrawWchar(u8g.getU8g(), x, y, c, max_length); u8g.setPrintPos(x + ret, y); - return ret; } int lcd_put_u8str_max(const char * utf8_str, pixel_len_t max_length) { - unsigned int x = u8g.getPrintCol(), - y = u8g.getPrintRow(), - ret = uxg_DrawUtf8Str(u8g.getU8g(), x, y, utf8_str, max_length); + u8g_uint_t x = u8g.getPrintCol(), y = u8g.getPrintRow(), + ret = uxg_DrawUtf8Str(u8g.getU8g(), x, y, utf8_str, max_length); u8g.setPrintPos(x + ret, y); return ret; } int lcd_put_u8str_max_P(PGM_P utf8_str_P, pixel_len_t max_length) { - unsigned int x = u8g.getPrintCol(), - y = u8g.getPrintRow(), - ret = uxg_DrawUtf8StrP(u8g.getU8g(), x, y, utf8_str_P, max_length); + u8g_uint_t x = u8g.getPrintCol(), y = u8g.getPrintRow(), + ret = uxg_DrawUtf8StrP(u8g.getU8g(), x, y, utf8_str_P, max_length); u8g.setPrintPos(x + ret, y); return ret; } diff --git a/Marlin/src/lcd/dogm/status_screen_DOGM.cpp b/Marlin/src/lcd/dogm/status_screen_DOGM.cpp index f04d2e89a5..a587d1b31b 100644 --- a/Marlin/src/lcd/dogm/status_screen_DOGM.cpp +++ b/Marlin/src/lcd/dogm/status_screen_DOGM.cpp @@ -520,10 +520,6 @@ void MarlinUI::draw_status_screen() { // XYZ Coordinates // - #define X_LABEL_POS 3 - #define X_VALUE_POS 11 - #define XYZ_SPACING 37 - #if ENABLED(XYZ_HOLLOW_FRAME) #define XYZ_FRAME_TOP 29 #define XYZ_FRAME_HEIGHT INFO_FONT_ASCENT + 3 diff --git a/Marlin/src/lcd/dogm/ultralcd_DOGM.cpp b/Marlin/src/lcd/dogm/ultralcd_DOGM.cpp index 0668f0afff..5d627de473 100644 --- a/Marlin/src/lcd/dogm/ultralcd_DOGM.cpp +++ b/Marlin/src/lcd/dogm/ultralcd_DOGM.cpp @@ -102,13 +102,15 @@ void MarlinUI::set_font(const MarlinFont font_nr) { } } +bool MarlinUI::detected() { return true; } + #if ENABLED(SHOW_BOOTSCREEN) #if ENABLED(SHOW_CUSTOM_BOOTSCREEN) // Draws a slice of a particular frame of the custom bootscreen, without the u8g loop void MarlinUI::draw_custom_bootscreen(const uint8_t frame/*=0*/) { constexpr u8g_uint_t left = u8g_uint_t((LCD_PIXEL_WIDTH - (CUSTOM_BOOTSCREEN_BMPWIDTH)) / 2), - top = u8g_uint_t((LCD_PIXEL_HEIGHT - (CUSTOM_BOOTSCREEN_BMPHEIGHT)) / 2); + top = u8g_uint_t((LCD_PIXEL_HEIGHT - (CUSTOM_BOOTSCREEN_BMPHEIGHT)) / 2); #if ENABLED(CUSTOM_BOOTSCREEN_INVERTED) constexpr u8g_uint_t right = left + CUSTOM_BOOTSCREEN_BMPWIDTH, bottom = top + CUSTOM_BOOTSCREEN_BMPHEIGHT; @@ -160,23 +162,23 @@ void MarlinUI::set_font(const MarlinFont font_nr) { // Draws a slice of the Marlin bootscreen, without the u8g loop void MarlinUI::draw_marlin_bootscreen() { // Screen dimensions. - //const uint8_t width = u8g.getWidth(), height = u8g.getHeight(); - constexpr uint8_t width = LCD_PIXEL_WIDTH, height = LCD_PIXEL_HEIGHT; + //const u8g_uint_t width = u8g.getWidth(), height = u8g.getHeight(); + constexpr u8g_uint_t width = LCD_PIXEL_WIDTH, height = LCD_PIXEL_HEIGHT; // Determine text space needed #ifndef STRING_SPLASH_LINE2 - constexpr uint8_t text_total_height = MENU_FONT_HEIGHT, - text_width_1 = uint8_t(sizeof(STRING_SPLASH_LINE1) - 1) * uint8_t(MENU_FONT_WIDTH), - text_width_2 = 0; + constexpr u8g_uint_t text_total_height = MENU_FONT_HEIGHT, + text_width_1 = u8g_uint_t(sizeof(STRING_SPLASH_LINE1) - 1) * u8g_uint_t(MENU_FONT_WIDTH), + text_width_2 = 0; #else - constexpr uint8_t text_total_height = uint8_t(MENU_FONT_HEIGHT) * 2, - text_width_1 = uint8_t(sizeof(STRING_SPLASH_LINE1) - 1) * uint8_t(MENU_FONT_WIDTH), - text_width_2 = uint8_t(sizeof(STRING_SPLASH_LINE2) - 1) * uint8_t(MENU_FONT_WIDTH); + constexpr u8g_uint_t text_total_height = u8g_uint_t(MENU_FONT_HEIGHT) * 2, + text_width_1 = u8g_uint_t(sizeof(STRING_SPLASH_LINE1) - 1) * u8g_uint_t(MENU_FONT_WIDTH), + text_width_2 = u8g_uint_t(sizeof(STRING_SPLASH_LINE2) - 1) * u8g_uint_t(MENU_FONT_WIDTH); #endif - constexpr uint8_t text_max_width = _MAX(text_width_1, text_width_2), - rspace = width - (START_BMPWIDTH); + constexpr u8g_uint_t text_max_width = _MAX(text_width_1, text_width_2), + rspace = width - (START_BMPWIDTH); - int8_t offx, offy, txt_base, txt_offx_1, txt_offx_2; + u8g_int_t offx, offy, txt_base, txt_offx_1, txt_offx_2; // Can the text fit to the right of the bitmap? if (text_max_width < rspace) { @@ -299,7 +301,7 @@ void MarlinUI::draw_kill_screen() { #if ENABLED(LIGHTWEIGHT_UI) ST7920_Lite_Status_Screen::clear_text_buffer(); #endif - const uint8_t h4 = u8g.getHeight() / 4; + const u8g_uint_t h4 = u8g.getHeight() / 4; u8g.firstPage(); do { set_font(FONT_MENU); @@ -316,7 +318,7 @@ void MarlinUI::clear_lcd() { } // Automatically cleared by Picture Loop #if HAS_LCD_MENU - uint8_t row_y1, row_y2; + u8g_uint_t row_y1, row_y2; #if ENABLED(ADVANCED_PAUSE_FEATURE) @@ -373,7 +375,7 @@ void MarlinUI::clear_lcd() { } // Automatically cleared by Picture Loop if (mark_as_selected(row, invert)) { - uint8_t n = LCD_PIXEL_WIDTH; // pixel width of string allowed + u8g_uint_t n = LCD_PIXEL_WIDTH; // pixel width of string allowed if (center && !valstr) { int8_t pad = (LCD_WIDTH - utf8_strlen_P(pstr)) / 2; @@ -390,7 +392,7 @@ void MarlinUI::clear_lcd() { } // Automatically cleared by Picture Loop UNUSED(pre_char); if (mark_as_selected(row, sel)) { - uint8_t n = (LCD_WIDTH - 2) * (MENU_FONT_WIDTH); + u8g_uint_t n = (LCD_WIDTH - 2) * (MENU_FONT_WIDTH); n -= lcd_put_u8str_max_P(pstr, n); while (n > MENU_FONT_WIDTH) n -= lcd_put_wchar(' '); lcd_moveto(LCD_PIXEL_WIDTH - (MENU_FONT_WIDTH), row_y2); @@ -403,7 +405,7 @@ void MarlinUI::clear_lcd() { } // Automatically cleared by Picture Loop void _draw_menu_item_edit(const bool sel, const uint8_t row, PGM_P const pstr, const char* const data, const bool pgm) { if (mark_as_selected(row, sel)) { const uint8_t vallen = (pgm ? utf8_strlen_P(data) : utf8_strlen((char*)data)); - uint8_t n = (LCD_WIDTH - 2 - vallen) * (MENU_FONT_WIDTH); + u8g_uint_t n = (LCD_WIDTH - 2 - vallen) * (MENU_FONT_WIDTH); n -= lcd_put_u8str_max_P(pstr, n); lcd_put_wchar(':'); while (n > MENU_FONT_WIDTH) n -= lcd_put_wchar(' '); @@ -415,13 +417,13 @@ void MarlinUI::clear_lcd() { } // Automatically cleared by Picture Loop void draw_edit_screen(PGM_P const pstr, const char* const value/*=nullptr*/) { ui.encoder_direction_normal(); - const uint8_t labellen = utf8_strlen_P(pstr), vallen = utf8_strlen(value); + const u8g_uint_t labellen = utf8_strlen_P(pstr), vallen = utf8_strlen(value); bool extra_row = labellen > LCD_WIDTH - 2 - vallen; #if ENABLED(USE_BIG_EDIT_FONT) // Use the menu font if the label won't fit on a single line - constexpr uint8_t lcd_edit_width = (LCD_PIXEL_WIDTH) / (EDIT_FONT_WIDTH); - uint8_t lcd_chr_fit, one_chr_width; + constexpr u8g_uint_t lcd_edit_width = (LCD_PIXEL_WIDTH) / (EDIT_FONT_WIDTH); + u8g_uint_t lcd_chr_fit, one_chr_width; if (labellen <= lcd_edit_width - 1) { if (labellen + vallen + 1 > lcd_edit_width) extra_row = true; lcd_chr_fit = lcd_edit_width + 1; @@ -434,13 +436,13 @@ void MarlinUI::clear_lcd() { } // Automatically cleared by Picture Loop ui.set_font(FONT_MENU); } #else - constexpr uint8_t lcd_chr_fit = LCD_WIDTH, - one_chr_width = MENU_FONT_WIDTH; + constexpr u8g_uint_t lcd_chr_fit = LCD_WIDTH, + one_chr_width = MENU_FONT_WIDTH; #endif // Center the label and value lines on the middle line - uint8_t baseline = extra_row ? (LCD_PIXEL_HEIGHT) / 2 - 1 - : (LCD_PIXEL_HEIGHT + EDIT_FONT_ASCENT) / 2; + u8g_uint_t baseline = extra_row ? (LCD_PIXEL_HEIGHT) / 2 - 1 + : (LCD_PIXEL_HEIGHT + EDIT_FONT_ASCENT) / 2; // Assume the label is alpha-numeric (with a descender) bool onpage = PAGE_CONTAINS(baseline - (EDIT_FONT_ASCENT - 1), baseline + EDIT_FONT_DESCENT); @@ -465,9 +467,9 @@ void MarlinUI::clear_lcd() { } // Automatically cleared by Picture Loop } } - inline void draw_boxed_string(const uint8_t x, const uint8_t y, PGM_P const pstr, const bool inv) { - const uint8_t len = utf8_strlen_P(pstr), bw = len * (MENU_FONT_WIDTH), - bx = x * (MENU_FONT_WIDTH), by = (y + 1) * (MENU_FONT_HEIGHT); + inline void draw_boxed_string(const u8g_uint_t x, const u8g_uint_t y, PGM_P const pstr, const bool inv) { + const u8g_uint_t len = utf8_strlen_P(pstr), bw = len * (MENU_FONT_WIDTH), + bx = x * (MENU_FONT_WIDTH), by = (y + 1) * (MENU_FONT_HEIGHT); if (inv) { u8g.setColorIndex(1); u8g.drawBox(bx - 1, by - (MENU_FONT_ASCENT) + 1, bw + 2, MENU_FONT_HEIGHT - 1); @@ -492,8 +494,8 @@ void MarlinUI::clear_lcd() { } // Automatically cleared by Picture Loop if (mark_as_selected(row, sel)) { if (isDir) lcd_put_wchar(LCD_STR_FOLDER[0]); constexpr uint8_t maxlen = LCD_WIDTH - 1; - const uint8_t pixw = maxlen * (MENU_FONT_WIDTH); - uint8_t n = pixw - lcd_put_u8str_max(ui.scrolled_filename(theCard, maxlen, row, sel), pixw); + const u8g_uint_t pixw = maxlen * (MENU_FONT_WIDTH); + u8g_uint_t n = pixw - lcd_put_u8str_max(ui.scrolled_filename(theCard, maxlen, row, sel), pixw); while (n > MENU_FONT_WIDTH) n -= lcd_put_wchar(' '); } } @@ -512,8 +514,8 @@ void MarlinUI::clear_lcd() { } // Automatically cleared by Picture Loop void MarlinUI::ubl_plot(const uint8_t x_plot, const uint8_t y_plot) { // Scale the box pixels appropriately - uint8_t x_map_pixels = ((MAP_MAX_PIXELS_X - 4) / (GRID_MAX_POINTS_X)) * (GRID_MAX_POINTS_X), - y_map_pixels = ((MAP_MAX_PIXELS_Y - 4) / (GRID_MAX_POINTS_Y)) * (GRID_MAX_POINTS_Y), + u8g_uint_t x_map_pixels = ((MAP_MAX_PIXELS_X - 4) / (GRID_MAX_POINTS_X)) * (GRID_MAX_POINTS_X), + y_map_pixels = ((MAP_MAX_PIXELS_Y - 4) / (GRID_MAX_POINTS_Y)) * (GRID_MAX_POINTS_Y), pixels_per_x_mesh_pnt = x_map_pixels / (GRID_MAX_POINTS_X), pixels_per_y_mesh_pnt = y_map_pixels / (GRID_MAX_POINTS_Y), @@ -535,8 +537,8 @@ void MarlinUI::clear_lcd() { } // Automatically cleared by Picture Loop // Display Mesh Point Locations u8g.setColorIndex(1); - const uint8_t sx = x_offset + pixels_per_x_mesh_pnt / 2; - uint8_t y = y_offset + pixels_per_y_mesh_pnt / 2; + const u8g_uint_t sx = x_offset + pixels_per_x_mesh_pnt / 2; + u8g_uint_t y = y_offset + pixels_per_y_mesh_pnt / 2; for (uint8_t j = 0; j < GRID_MAX_POINTS_Y; j++, y += pixels_per_y_mesh_pnt) if (PAGE_CONTAINS(y, y)) for (uint8_t i = 0, x = sx; i < GRID_MAX_POINTS_X; i++, x += pixels_per_x_mesh_pnt) @@ -544,10 +546,10 @@ void MarlinUI::clear_lcd() { } // Automatically cleared by Picture Loop // Fill in the Specified Mesh Point - uint8_t inverted_y = GRID_MAX_POINTS_Y - y_plot - 1; // The origin is typically in the lower right corner. We need to - // invert the Y to get it to plot in the right location. + const uint8_t y_plot_inv = (GRID_MAX_POINTS_Y - 1) - y_plot; // The origin is typically in the lower right corner. We need to + // invert the Y to get it to plot in the right location. - const uint8_t by = y_offset + inverted_y * pixels_per_y_mesh_pnt; + const u8g_uint_t by = y_offset + y_plot_inv * pixels_per_y_mesh_pnt; if (PAGE_CONTAINS(by, by + pixels_per_y_mesh_pnt)) u8g.drawBox( x_offset + x_plot * pixels_per_x_mesh_pnt, by, diff --git a/Marlin/src/lcd/lcdprint.h b/Marlin/src/lcd/lcdprint.h index 59cd546855..cbb9ec357f 100644 --- a/Marlin/src/lcd/lcdprint.h +++ b/Marlin/src/lcd/lcdprint.h @@ -14,8 +14,10 @@ #if HAS_GRAPHICAL_LCD #include "dogm/u8g_fontutf8.h" + typedef u8g_uint_t lcd_uint_t; #else #define _UxGT(a) a + typedef uint8_t lcd_uint_t; #endif #define START_OF_UTF8_CHAR(C) (((C) & 0xC0u) != 0x80u) @@ -48,7 +50,7 @@ int lcd_put_u8str_max(const char * utf8_str, pixel_len_t max_length); */ int lcd_put_u8str_max_P(PGM_P utf8_str_P, pixel_len_t max_length); -void lcd_moveto(const uint8_t col, const uint8_t row); +void lcd_moveto(const lcd_uint_t col, const lcd_uint_t row); void lcd_put_int(const int i); diff --git a/Marlin/src/lcd/menu/menu_delta_calibrate.cpp b/Marlin/src/lcd/menu/menu_delta_calibrate.cpp index a4770d0f86..3925bfbbb6 100644 --- a/Marlin/src/lcd/menu/menu_delta_calibrate.cpp +++ b/Marlin/src/lcd/menu/menu_delta_calibrate.cpp @@ -36,6 +36,10 @@ #include "../../feature/bedlevel/bedlevel.h" #endif +#if ENABLED(EXTENSIBLE_UI) + #include "../../lcd/extensible_ui/ui_api.h" +#endif + void _man_probe_pt(const float &rx, const float &ry) { do_blocking_move_to(rx, ry, Z_CLEARANCE_BETWEEN_PROBES); ui.synchronize(); @@ -55,6 +59,9 @@ void _man_probe_pt(const float &rx, const float &ry) { #if ENABLED(HOST_PROMPT_SUPPORT) host_prompt_do(PROMPT_USER_CONTINUE, PSTR("Delta Calibration in progress"), PSTR("Continue")); #endif + #if ENABLED(EXTENSIBLE_UI) + ExtUI::onStatusChanged(PSTR("Delta Calibration in progress")); + #endif while (wait_for_user) idle(); ui.goto_previous_screen_no_defer(); return current_position[Z_AXIS]; diff --git a/Marlin/src/lcd/menu/menu_ubl.cpp b/Marlin/src/lcd/menu/menu_ubl.cpp index b3bb94cb16..85e42a8b87 100644 --- a/Marlin/src/lcd/menu/menu_ubl.cpp +++ b/Marlin/src/lcd/menu/menu_ubl.cpp @@ -37,10 +37,9 @@ static int16_t ubl_storage_slot = 0, custom_hotend_temp = 190, side_points = 3, ubl_fillin_amount = 5, - ubl_height_amount = 1, - n_edit_pts = 1, - x_plot = 0, - y_plot = 0; + ubl_height_amount = 1; + +static uint8_t n_edit_pts = 1, x_plot = 0, y_plot = 0; #if HAS_HEATED_BED static int16_t custom_bed_temp = 50; @@ -423,7 +422,7 @@ void _lcd_ubl_map_lcd_edit_cmd() { char ubl_lcd_gcode[50], str[10], str2[10]; dtostrf(pgm_read_float(&ubl._mesh_index_to_xpos[x_plot]), 0, 2, str); dtostrf(pgm_read_float(&ubl._mesh_index_to_ypos[y_plot]), 0, 2, str2); - snprintf_P(ubl_lcd_gcode, sizeof(ubl_lcd_gcode), PSTR("G29 P4 X%s Y%s R%i"), str, str2, n_edit_pts); + snprintf_P(ubl_lcd_gcode, sizeof(ubl_lcd_gcode), PSTR("G29 P4 X%s Y%s R%i"), str, str2, int(n_edit_pts)); lcd_enqueue_one_now(ubl_lcd_gcode); } diff --git a/Marlin/src/lcd/ultralcd.cpp b/Marlin/src/lcd/ultralcd.cpp index ce9d9d7032..f201c1b2a0 100644 --- a/Marlin/src/lcd/ultralcd.cpp +++ b/Marlin/src/lcd/ultralcd.cpp @@ -64,6 +64,19 @@ uint8_t MarlinUI::progress_bar_percent; // = 0 #endif +#if HAS_BUZZER + #include "../libs/buzzer.h" + void MarlinUI::buzz(const long duration, const uint16_t freq) { + #if ENABLED(LCD_USE_I2C_BUZZER) + lcd.buzz(duration, freq); + #elif ENABLED(PCA9632_BUZZER) + pca9632_buzz(const long duration, const uint16_t freq) { + #elif USE_BEEPER + buzzer.tone(duration, freq); + #endif + } +#endif + #if HAS_SPI_LCD #if HAS_GRAPHICAL_LCD @@ -89,10 +102,6 @@ #include "../feature/bedlevel/bedlevel.h" #endif -#if HAS_BUZZER - #include "../libs/buzzer.h" -#endif - #if HAS_TRINAMIC #include "../feature/tmc_util.h" #endif @@ -205,13 +214,13 @@ millis_t next_button_update_ms; #endif - void _wrap_string(uint8_t &x, uint8_t &y, const char * const string, read_byte_cb_t cb_read_byte, bool wordwrap/*=false*/) { - SETCURSOR(x, y); + void _wrap_string(uint8_t &col, uint8_t &row, const char * const string, read_byte_cb_t cb_read_byte, bool wordwrap/*=false*/) { + SETCURSOR(col, row); if (!string) return; - auto _newline = [&x, &y]() { - x = 0; y++; // move x to string len (plus space) - SETCURSOR(0, y); // simulate carriage return + auto _newline = [&col, &row]() { + col = 0; row++; // Move col to string len (plus space) + SETCURSOR(0, row); // Simulate carriage return }; uint8_t *p = (uint8_t*)string; @@ -227,9 +236,9 @@ millis_t next_button_update_ms; if (eol || ch == ' ' || ch == '-' || ch == '+' || ch == '.') { if (!c && ch == ' ') { if (wrd) wrd++; continue; } // collapse extra spaces // Past the right and the word is not too long? - if (x + c > LCD_WIDTH && x >= (LCD_WIDTH) / 4) _newline(); // should it wrap? + if (col + c > LCD_WIDTH && col >= (LCD_WIDTH) / 4) _newline(); // should it wrap? c += !eol; // +1 so the space will be printed - x += c; // advance x to new position + col += c; // advance col to new position while (c) { // character countdown --c; // count down to zero wrd = get_utf8_value_cb(wrd, cb_read_byte, &ch); // get characters again @@ -246,25 +255,25 @@ millis_t next_button_update_ms; p = get_utf8_value_cb(p, cb_read_byte, &ch); if (!ch) break; lcd_put_wchar(ch); - x++; - if (x >= LCD_WIDTH) _newline(); + col++; + if (col >= LCD_WIDTH) _newline(); } } } void MarlinUI::draw_select_screen_prompt(PGM_P const pref, const char * const string/*=nullptr*/, PGM_P const suff/*=nullptr*/) { const uint8_t plen = utf8_strlen_P(pref), slen = suff ? utf8_strlen_P(suff) : 0; - uint8_t x = 0, y = 0; + uint8_t row = 0, col = 0; if (!string && plen + slen <= LCD_WIDTH) { - x = (LCD_WIDTH - plen - slen) / 2; - y = LCD_HEIGHT > 3 ? 1 : 0; + row = (LCD_WIDTH - plen - slen) / 2; + col = LCD_HEIGHT > 3 ? 1 : 0; } - wrap_string_P(x, y, pref, true); + wrap_string_P(row, col, pref, true); if (string) { - if (x) { x = 0; y++; } // Move to the start of the next line - wrap_string(x, y, string); + if (row) { row = 0; col++; } // Move to the start of the next line + wrap_string(row, col, string); } - if (suff) wrap_string_P(x, y, suff); + if (suff) wrap_string_P(row, col, suff); } #endif // HAS_LCD_MENU @@ -568,7 +577,7 @@ void MarlinUI::status_screen() { const millis_t ms = millis(); #endif if (ELAPSED(ms, next_beep)) { - BUZZ(FEEDRATE_CHANGE_BEEP_DURATION, FEEDRATE_CHANGE_BEEP_FREQUENCY); + buzz(FEEDRATE_CHANGE_BEEP_DURATION, FEEDRATE_CHANGE_BEEP_FREQUENCY); next_beep = ms + 500UL; } #endif @@ -611,13 +620,12 @@ void MarlinUI::quick_feedback(const bool clear_buttons/*=true*/) { #if HAS_BUZZER // Buzz and wait. Is the delay needed for buttons to settle? buzz(LCD_FEEDBACK_FREQUENCY_DURATION_MS, LCD_FEEDBACK_FREQUENCY_HZ); - #endif - - #if HAS_LCD_MENU - #if ENABLED(LCD_USE_I2C_BUZZER) - delay(10); - #elif PIN_EXISTS(BEEPER) - for (int8_t i = 5; i--;) { buzzer.tick(); delay(2); } + #if HAS_LCD_MENU + #if USE_BEEPER + for (int8_t i = 5; i--;) { buzzer.tick(); delay(2); } + #else + delay(10); + #endif #endif #endif } @@ -729,16 +737,6 @@ void MarlinUI::quick_feedback(const bool clear_buttons/*=true*/) { LCDViewAction MarlinUI::lcdDrawUpdate = LCDVIEW_CLEAR_CALL_REDRAW; -bool MarlinUI::detected() { - return - #if EITHER(LCD_I2C_TYPE_MCP23017, LCD_I2C_TYPE_MCP23008) && defined(DETECT_DEVICE) - lcd.LcdDetected() == 1 - #else - true - #endif - ; -} - void MarlinUI::update() { static uint16_t max_display_update_time = 0; @@ -1295,23 +1293,6 @@ void MarlinUI::update() { #endif // HAS_ENCODER_WHEEL } - #if HAS_SLOW_BUTTONS - - uint8_t MarlinUI::read_slow_buttons() { - #if ENABLED(LCD_I2C_TYPE_MCP23017) - // Reading these buttons this is likely to be too slow to call inside interrupt context - // so they are called during normal lcd_update - uint8_t slow_bits = lcd.readButtons() << B_I2C_BTN_OFFSET; - #if ENABLED(LCD_I2C_VIKI) - if ((slow_bits & (B_MI | B_RI)) && PENDING(millis(), next_button_update_ms)) // LCD clicked - slow_bits &= ~(B_MI | B_RI); // Disable LCD clicked buttons if screen is updated - #endif // LCD_I2C_VIKI - return slow_bits; - #endif // LCD_I2C_TYPE_MCP23017 - } - - #endif - #endif // HAS_ENCODER_ACTION #endif // HAS_SPI_LCD diff --git a/Marlin/src/lcd/ultralcd.h b/Marlin/src/lcd/ultralcd.h index 60a111d1c4..4d0a541e19 100644 --- a/Marlin/src/lcd/ultralcd.h +++ b/Marlin/src/lcd/ultralcd.h @@ -76,11 +76,11 @@ #define LCDWRITE(c) lcd_put_wchar(c) #endif - #include "fontutils.h" + #include "lcdprint.h" - void _wrap_string(uint8_t &x, uint8_t &y, const char * const string, read_byte_cb_t cb_read_byte, const bool wordwrap=false); - inline void wrap_string_P(uint8_t &x, uint8_t &y, PGM_P const pstr, const bool wordwrap=false) { _wrap_string(x, y, pstr, read_byte_rom, wordwrap); } - inline void wrap_string(uint8_t &x, uint8_t &y, const char * const string, const bool wordwrap=false) { _wrap_string(x, y, string, read_byte_ram, wordwrap); } + void _wrap_string(uint8_t &col, uint8_t &row, const char * const string, read_byte_cb_t cb_read_byte, const bool wordwrap=false); + inline void wrap_string_P(uint8_t &col, uint8_t &row, PGM_P const pstr, const bool wordwrap=false) { _wrap_string(col, row, pstr, read_byte_rom, wordwrap); } + inline void wrap_string(uint8_t &col, uint8_t &row, const char * const string, const bool wordwrap=false) { _wrap_string(col, row, string, read_byte_ram, wordwrap); } #if ENABLED(SDSUPPORT) #include "../sd/cardreader.h" @@ -259,15 +259,11 @@ public: } #if HAS_BUZZER - static inline void buzz(const long duration, const uint16_t freq) { - #if ENABLED(LCD_USE_I2C_BUZZER) - lcd.buzz(duration, freq); - #elif PIN_EXISTS(BEEPER) - buzzer.tone(duration, freq); - #elif ENABLED(PCA9632_BUZZER) - pca9632_buzz(duration, freq); - #endif - } + static void buzz(const long duration, const uint16_t freq); + #endif + + #if ENABLED(LCD_HAS_STATUS_INDICATORS) + static void update_indicators(); #endif // LCD implementations @@ -486,7 +482,7 @@ public: #endif #if ENABLED(AUTO_BED_LEVELING_UBL) - static void ubl_plot(const uint8_t x, const uint8_t inverted_y); + static void ubl_plot(const uint8_t x_plot, const uint8_t y_plot); #endif static void draw_select_screen_prompt(PGM_P const pref, const char * const string=nullptr, PGM_P const suff=nullptr); diff --git a/Marlin/src/libs/buzzer.cpp b/Marlin/src/libs/buzzer.cpp index aa20127fa0..549c76008e 100644 --- a/Marlin/src/libs/buzzer.cpp +++ b/Marlin/src/libs/buzzer.cpp @@ -22,7 +22,7 @@ #include "../inc/MarlinConfig.h" -#if DISABLED(LCD_USE_I2C_BUZZER) && PIN_EXISTS(BEEPER) +#if USE_BEEPER #include "buzzer.h" #include "../module/temperature.h" @@ -78,4 +78,4 @@ void Buzzer::tick() { else if (ELAPSED(now, state.endtime)) reset(); } -#endif // !LCD_USE_I2C_BUZZER && BEEPER +#endif // USE_BEEPER diff --git a/Marlin/src/libs/buzzer.h b/Marlin/src/libs/buzzer.h index 1908b6aeaf..026b9330f9 100644 --- a/Marlin/src/libs/buzzer.h +++ b/Marlin/src/libs/buzzer.h @@ -23,16 +23,7 @@ #include "../inc/MarlinConfig.h" -#if ENABLED(LCD_USE_I2C_BUZZER) - - #define BUZZ(d,f) ui.buzz(d,f) - -#elif ENABLED(PCA9632_BUZZER) - - #include "../feature/leds/pca9632.h" - #define BUZZ(d, f) pca9632_buzz(d,f) - -#elif PIN_EXISTS(BEEPER) +#if USE_BEEPER #include "circularqueue.h" @@ -120,10 +111,18 @@ // Provide a buzzer instance extern Buzzer buzzer; + + // Buzz directly via the BEEPER pin tone queue #define BUZZ(d,f) buzzer.tone(d, f) -#else // No buzz capability +#elif HAS_BUZZER + // Buzz indirectly via the MarlinUI instance + #define BUZZ(d,f) ui.buzz(d,f) + +#else + + // No buzz capability #define BUZZ(d,f) NOOP #endif diff --git a/Marlin/src/module/configuration_store.cpp b/Marlin/src/module/configuration_store.cpp index 161e360c21..cc5b15b57c 100644 --- a/Marlin/src/module/configuration_store.cpp +++ b/Marlin/src/module/configuration_store.cpp @@ -2798,12 +2798,6 @@ void MarlinSettings::reset() { } #endif - #if HAS_FILAMENT_SENSOR - CONFIG_ECHO_HEADING("Filament Runout Sensor:"); - CONFIG_ECHO_START(); - SERIAL_ECHOLNPAIR(" M412 S", int(runout.enabled)); - #endif - /** * Bed Leveling */ diff --git a/Marlin/src/module/motion.cpp b/Marlin/src/module/motion.cpp index 85d9362ef8..a31f1c08e5 100644 --- a/Marlin/src/module/motion.cpp +++ b/Marlin/src/module/motion.cpp @@ -1663,7 +1663,7 @@ void homeaxis(const AxisEnum axis) { ]; if (backoff_mm) { current_position[axis] -= ABS(backoff_mm) * axis_home_dir; - line_to_current_position(); + line_to_current_position(Z_PROBE_SPEED_FAST); } #endif diff --git a/Marlin/src/module/printcounter.cpp b/Marlin/src/module/printcounter.cpp index 25e8a767ab..ba308142e4 100644 --- a/Marlin/src/module/printcounter.cpp +++ b/Marlin/src/module/printcounter.cpp @@ -157,6 +157,8 @@ void PrintCounter::loadStats() { #endif #if HAS_BUZZER && SERVICE_WARNING_BUZZES > 0 if (doBuzz) for (int i = 0; i < SERVICE_WARNING_BUZZES; i++) BUZZ(200, 404); + #else + UNUSED(doBuzz); #endif #endif // HAS_SERVICE_INTERVALS } diff --git a/Marlin/src/module/probe.cpp b/Marlin/src/module/probe.cpp index 91b699aa04..4f63cdd453 100644 --- a/Marlin/src/module/probe.cpp +++ b/Marlin/src/module/probe.cpp @@ -79,6 +79,10 @@ float zprobe_zoffset; // Initialized by settings.load() #include "stepper_indirection.h" #endif +#if ENABLED(EXTENSIBLE_UI) + #include "../lcd/extensible_ui/ui_api.h" +#endif + #define DEBUG_OUT ENABLED(DEBUG_LEVELING_FEATURE) #include "../core/debug_out.h" @@ -114,6 +118,7 @@ float zprobe_zoffset; // Initialized by settings.load() #endif #if ENABLED(TOUCH_MI_MANUAL_DEPLOY) + const screenFunc_t prev_screen = ui.currentScreen; LCD_MESSAGEPGM(MSG_MANUAL_DEPLOY_TOUCHMI); ui.return_to_status(); @@ -126,10 +131,11 @@ float zprobe_zoffset; // Initialized by settings.load() while (wait_for_user) idle(); ui.reset_status(); ui.goto_screen(prev_screen); - #else - #ifdef TOUCH_MI_DEPLOY_XPOS - do_blocking_move_to_x(TOUCH_MI_DEPLOY_XPOS); - #endif + + #elif defined(TOUCH_MI_DEPLOY_XPOS) + + do_blocking_move_to_x(TOUCH_MI_DEPLOY_XPOS); + #endif } @@ -371,6 +377,9 @@ FORCE_INLINE void probe_specific_action(const bool deploy) { #if ENABLED(HOST_PROMPT_SUPPORT) host_prompt_do(PROMPT_USER_CONTINUE, PSTR("Stow Probe"), PSTR("Continue")); #endif + #if ENABLED(EXTENSIBLE_UI) + ExtUI::onStatusChanged(PSTR("Stow Probe")); + #endif while (wait_for_user) idle(); ui.reset_status(); diff --git a/Marlin/src/module/temperature.cpp b/Marlin/src/module/temperature.cpp index 79f63b5315..04492987b7 100644 --- a/Marlin/src/module/temperature.cpp +++ b/Marlin/src/module/temperature.cpp @@ -68,7 +68,7 @@ #include "tool_change.h" #endif -#if HAS_BUZZER && PIN_EXISTS(BEEPER) +#if USE_BEEPER #include "../libs/buzzer.h" #endif @@ -749,7 +749,7 @@ int16_t Temperature::getHeaterPower(const heater_ind_t heater_id) { inline void loud_kill(PGM_P const lcd_msg) { Running = false; - #if HAS_BUZZER && PIN_EXISTS(BEEPER) + #if USE_BEEPER for (uint8_t i = 20; i--;) { WRITE(BEEPER_PIN, HIGH); delay(25); WRITE(BEEPER_PIN, LOW); delay(80); diff --git a/Marlin/src/module/thermistor/thermistor_331.h b/Marlin/src/module/thermistor/thermistor_331.h new file mode 100644 index 0000000000..8f98d07523 --- /dev/null +++ b/Marlin/src/module/thermistor/thermistor_331.h @@ -0,0 +1,92 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +#define OVM(V) OV((V)*(0.327/0.5)) + +// R25 = 100 kOhm, beta25 = 4092 K, 4.7 kOhm pull-up, bed thermistor +const short temptable_331[][2] PROGMEM = { + { OVM( 23), 300 }, + { OVM( 25), 295 }, + { OVM( 27), 290 }, + { OVM( 28), 285 }, + { OVM( 31), 280 }, + { OVM( 33), 275 }, + { OVM( 35), 270 }, + { OVM( 38), 265 }, + { OVM( 41), 260 }, + { OVM( 44), 255 }, + { OVM( 48), 250 }, + { OVM( 52), 245 }, + { OVM( 56), 240 }, + { OVM( 61), 235 }, + { OVM( 66), 230 }, + { OVM( 71), 225 }, + { OVM( 78), 220 }, + { OVM( 84), 215 }, + { OVM( 92), 210 }, + { OVM( 100), 205 }, + { OVM( 109), 200 }, + { OVM( 120), 195 }, + { OVM( 131), 190 }, + { OVM( 143), 185 }, + { OVM( 156), 180 }, + { OVM( 171), 175 }, + { OVM( 187), 170 }, + { OVM( 205), 165 }, + { OVM( 224), 160 }, + { OVM( 245), 155 }, + { OVM( 268), 150 }, + { OVM( 293), 145 }, + { OVM( 320), 140 }, + { OVM( 348), 135 }, + { OVM( 379), 130 }, + { OVM( 411), 125 }, + { OVM( 445), 120 }, + { OVM( 480), 115 }, + { OVM( 516), 110 }, + { OVM( 553), 105 }, + { OVM( 591), 100 }, + { OVM( 628), 95 }, + { OVM( 665), 90 }, + { OVM( 702), 85 }, + { OVM( 737), 80 }, + { OVM( 770), 75 }, + { OVM( 801), 70 }, + { OVM( 830), 65 }, + { OVM( 857), 60 }, + { OVM( 881), 55 }, + { OVM( 903), 50 }, + { OVM( 922), 45 }, + { OVM( 939), 40 }, + { OVM( 954), 35 }, + { OVM( 966), 30 }, + { OVM( 977), 25 }, + { OVM( 985), 20 }, + { OVM( 993), 15 }, + { OVM( 999), 10 }, + { OVM(1004), 5 }, + { OVM(1008), 0 }, + { OVM(1012), -5 }, + { OVM(1016), -10 }, + { OVM(1020), -15 } +}; diff --git a/Marlin/src/module/thermistor/thermistors.h b/Marlin/src/module/thermistor/thermistors.h index f91c2be943..f42f647e85 100644 --- a/Marlin/src/module/thermistor/thermistors.h +++ b/Marlin/src/module/thermistor/thermistors.h @@ -131,6 +131,9 @@ #if ANY_THERMISTOR_IS(201) // Pt100 with LMV324 Overlord #include "thermistor_201.h" #endif +#if ANY_THERMISTOR_IS(331) // Like table 1, but with 3V3 as input voltage + #include "thermistor_331.h" +#endif #if ANY_THERMISTOR_IS(666) // beta25 = UNK, R25 = 200K, Pull-up = 10 kOhm, "Unidentified 200K NTC thermistor (Einstart S)" #include "thermistor_666.h" #endif diff --git a/Marlin/src/pins/mega/pins_CNCONTROLS_15.h b/Marlin/src/pins/mega/pins_CNCONTROLS_15.h new file mode 100644 index 0000000000..5c550a6197 --- /dev/null +++ b/Marlin/src/pins/mega/pins_CNCONTROLS_15.h @@ -0,0 +1,86 @@ +/** + * CNControls V15 for HMS434 pin assignments + */ + +#if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__) + #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'" +#endif + +#define BOARD_NAME "CN Controls V15" + +// +// Servos +// +#define SERVO0_PIN 6 + +// +// Limit Switches +// +#define X_STOP_PIN 34 +#define Y_STOP_PIN 39 +#define Z_STOP_PIN 62 + +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN 49 +#endif + +// +// Steppers +// +#define X_STEP_PIN 14 +#define X_DIR_PIN 25 +#define X_ENABLE_PIN 26 + +#define Y_STEP_PIN 11 +#define Y_DIR_PIN 12 +#define Y_ENABLE_PIN 15 + +#define Z_STEP_PIN 24 +#define Z_DIR_PIN 27 +#define Z_ENABLE_PIN 28 + +#define E0_STEP_PIN 64 +#define E0_DIR_PIN 65 +#define E0_ENABLE_PIN 63 + +// +// Temperature Sensors +// Analog Inputs +// +#define TEMP_0_PIN 2 // Analog Input +#define TEMP_BED_PIN 4 // Analog Input +#define TEMP_CHAMBER_PIN 5 // Analog Input + +// +// Heaters +// +#define HEATER_0_PIN 4 +#define HEATER_BED_PIN 32 +#define HEATER_CHAMBER_PIN 33 + +// +// Fans +// +#define FAN0_PIN 8 +#define ORIG_E0_AUTO_FAN_PIN 30 +#define ORIG_E1_AUTO_FAN_PIN 30 +#define ORIG_E2_AUTO_FAN_PIN 30 +#define ORIG_E3_AUTO_FAN_PIN 30 +//#define ORIG_CHAMBER_AUTO_FAN_PIN 10 + +// +// Misc. Functions +// +#define SDSS 53 +#define SD_DETECT_PIN 40 + +// Common I/O + +#define FIL_RUNOUT_PIN 9 +//#define FIL_RUNOUT_PIN 29 // encoder sensor +//#define PWM_1_PIN 12 +//#define PWM_2_PIN 13 +//#define SPARE_IO 17 +#define BEEPER_PIN 13 +#define STAT_LED_BLUE_PIN -1 +#define STAT_LED_RED_PIN 10 // 31 diff --git a/Marlin/src/pins/mega/pins_WANHAO_ONEPLUS.h b/Marlin/src/pins/mega/pins_WANHAO_ONEPLUS.h index 86f295b622..f828d80727 100644 --- a/Marlin/src/pins/mega/pins_WANHAO_ONEPLUS.h +++ b/Marlin/src/pins/mega/pins_WANHAO_ONEPLUS.h @@ -92,20 +92,22 @@ #define KILL_PIN 64 // -// LCD / Controller +// LCD / Controller (Integrated MINIPANEL) // - -#if HAS_SPI_LCD +#if ENABLED(MINIPANEL) #define DOGLCD_A0 40 #define DOGLCD_CS 41 #define LCD_BACKLIGHT_PIN 65 // Backlight LED on A11/D65 #define LCD_RESET_PIN 27 - #define LCD_CONTRAST 255 + #define BTN_EN1 2 + #define BTN_EN2 3 + #define BTN_ENC 5 - #if ENABLED(NEWPANEL) - #define BTN_EN1 2 - #define BTN_EN2 3 - #define BTN_ENC 5 - #endif + // This display has adjustable contrast + #undef HAS_LCD_CONTRAST + #define HAS_LCD_CONTRAST 1 + #define LCD_CONTRAST_MIN 0 + #define LCD_CONTRAST_MAX 255 + #define DEFAULT_LCD_CONTRAST 255 #endif diff --git a/Marlin/src/pins/pins.h b/Marlin/src/pins/pins.h index b0ac655286..e5a75ffc5a 100644 --- a/Marlin/src/pins/pins.h +++ b/Marlin/src/pins/pins.h @@ -202,6 +202,8 @@ #include "mega/pins_CNCONTROLS_11.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(CNCONTROLS_12) #include "mega/pins_CNCONTROLS_12.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 +#elif MB(CNCONTROLS_15) + #include "mega/pins_CNCONTROLS_15.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(MIGHTYBOARD_REVE) #include "mega/pins_MIGHTYBOARD_REVE.h" // ATmega1280, ATmega2560 env:megaatmega1280 env:megaatmega2560 #elif MB(CHEAPTRONIC) @@ -502,6 +504,8 @@ #include "stm32/pins_STEVAL.h" // STM32F4 env:STM32F4 #elif MB(BIGTREE_SKR_PRO_V1_1) #include "stm32/pins_BIGTREE_SKR_PRO_V1.1.h" // STM32F4 env:BIGTREE_SKR_PRO +#elif MB(BIGTREE_BTT002_V1_0) + #include "stm32/pins_BIGTREE_BTT002_V1.0.h" // STM32F4 env:BIGTREE_BTT002 // // ARM Cortex M7 diff --git a/Marlin/src/pins/ramps/pins_RAMPS_CREALITY.h b/Marlin/src/pins/ramps/pins_RAMPS_CREALITY.h index 17885f8b1f..c1196459e9 100644 --- a/Marlin/src/pins/ramps/pins_RAMPS_CREALITY.h +++ b/Marlin/src/pins/ramps/pins_RAMPS_CREALITY.h @@ -35,7 +35,11 @@ #define MOSFET_D_PIN 7 #define FIL_RUNOUT_PIN 2 -#define SD_DETECT_PIN 49 //always define it here, even without an LCD as its onboard +#if NUM_RUNOUT_SENSORS > 1 + #define FIL_RUNOUT2_PIN 15 // Creality CR-X can use dual runout sensors +#endif + +#define SD_DETECT_PIN 49 // Always define onboard SD detect #include "pins_RAMPS.h" diff --git a/Marlin/src/pins/stm32/pins_BIGTREE_BTT002_V1.0.h b/Marlin/src/pins/stm32/pins_BIGTREE_BTT002_V1.0.h new file mode 100644 index 0000000000..213ddd1a63 --- /dev/null +++ b/Marlin/src/pins/stm32/pins_BIGTREE_BTT002_V1.0.h @@ -0,0 +1,254 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +#ifndef TARGET_STM32F4 + #error "Oops! Select an STM32F4 board in 'Tools > Board.'" +#elif HOTENDS > 3 || E_STEPPERS > 3 + #error "BIGTREE SKR Pro V1.1 supports up to 3 hotends / E-steppers." +#endif + +#define BOARD_NAME "BIGTREE Btt002 1.0" + +#define SRAM_EEPROM_EMULATION + +// Ignore temp readings during development. +//#define BOGUS_TEMPERATURE_GRACE_PERIOD 2000 + +// +// Servos +// +#define SERVO0_PIN PC3 + +// +// Limit Switches +// +#define X_MIN_PIN PD3 +#define X_MAX_PIN PD3 +#define Y_MIN_PIN PD2 +#define Y_MAX_PIN PD2 +#define Z_MIN_PIN PD1 +#define Z_MAX_PIN PD1 + +// +// Z Probe must be this pins ## +// +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN PD1 +#endif + +// +// Steppers +// +#define X_STEP_PIN PA9 +#define X_DIR_PIN PA10 +#define X_ENABLE_PIN PA8 +#ifndef X_CS_PIN + #define X_CS_PIN PE2 +#endif + +#define Y_STEP_PIN PC8 +#define Y_DIR_PIN PC9 +#define Y_ENABLE_PIN PC7 + #ifndef Y_CS_PIN + #define Y_CS_PIN PE3 +#endif + +#define Z_STEP_PIN PD15 +#define Z_DIR_PIN PC6 +#define Z_ENABLE_PIN PD14 +#ifndef Z_CS_PIN + #define Z_CS_PIN PE4 +#endif + +#define E0_STEP_PIN PD12 +#define E0_DIR_PIN PD13 +#define E0_ENABLE_PIN PD11 +#ifndef E0_CS_PIN + #define E0_CS_PIN PD7 +#endif + +/* +//SKR_PRO_V1.1 +#define E1_STEP_PIN PD15 +#define E1_DIR_PIN PE7 +#define E1_ENABLE_PIN PA3 +#ifndef E1_CS_PIN + #define E1_CS_PIN PG15 +#endif + +#define E2_STEP_PIN PD13 +#define E2_DIR_PIN PG9 +#define E2_ENABLE_PIN PF0 +#ifndef E2_CS_PIN + #define E2_CS_PIN PG12 +#endif +*/ +// +// Software SPI pins for TMC2130 stepper drivers +// +#if ENABLED(TMC_USE_SW_SPI) + #ifndef TMC_SW_MOSI + #define TMC_SW_MOSI PB15 + #endif + #ifndef TMC_SW_MISO + #define TMC_SW_MISO PB14 + #endif + #ifndef TMC_SW_SCK + #define TMC_SW_SCK PB13 + #endif +#endif + +#if HAS_TMC220x + /** + * TMC2208/TMC2209 stepper drivers + * + * Hardware serial communication ports. + * If undefined software serial is used according to the pins below + */ + //#define X_HARDWARE_SERIAL Serial1 + //#define X2_HARDWARE_SERIAL Serial1 + //#define Y_HARDWARE_SERIAL Serial1 + //#define Y2_HARDWARE_SERIAL Serial1 + //#define Z_HARDWARE_SERIAL Serial1 + //#define Z2_HARDWARE_SERIAL Serial1 + //#define E0_HARDWARE_SERIAL Serial1 + //#define E1_HARDWARE_SERIAL Serial1 + //#define E2_HARDWARE_SERIAL Serial1 + //#define E3_HARDWARE_SERIAL Serial1 + //#define E4_HARDWARE_SERIAL Serial1 + + // + // Software serial ## + // + #define X_SERIAL_TX_PIN PE2 + #define X_SERIAL_RX_PIN PE2 + + #define Y_SERIAL_TX_PIN PE3 + #define Y_SERIAL_RX_PIN PE3 + + #define Z_SERIAL_TX_PIN PE4 + #define Z_SERIAL_RX_PIN PE4 + + #define E0_SERIAL_TX_PIN PD7 + #define E0_SERIAL_RX_PIN PD7 + + //#define E1_SERIAL_TX_PIN PD1 + //#define E1_SERIAL_RX_PIN PD1 + + //#define E2_SERIAL_TX_PIN PD6 + //#define E2_SERIAL_RX_PIN PD6 +#endif + +// +// Temperature Sensors +// +#define TEMP_0_PIN PA2 // T1 <-> E0 +#define TEMP_1_PIN PA0 // T2 <-> E1 +//#define TEMP_2_PIN PC2 // T3 <-> E2 SKR_PRO +#define TEMP_BED_PIN PA1 // T0 <-> Bed + +// +// Heaters / Fans +// +#define HEATER_0_PIN PE6 // Heater0 +//#define HEATER_1_PIN PD14 // Heater1 +//#define HEATER_2_PIN PB0 // Heater1 +#define HEATER_BED_PIN PE5 // Hotbed +#define FAN_PIN PB9 // Fan0 +#define FAN1_PIN PB8 // Fan1 +//#define FAN2_PIN PE6 // Fan2 + +// HAL SPI pins group +#define SCK_PIN PA5 // SPI SCLK +#define MYSSEL PA4 // SPI SSEL +#define MISO_PIN PA6 // SPI MISO +#define MOSI_PIN PA7 // SPI MOSI + +// +// Misc. Functions +// +#define SDSS PA4 + +/** + * -------------------------------------SKR_MK3----------------------------------------------- + * _____ _____ | + * PA3 | · · | GND 5V | · · | GND | + * NRESET | · · | PC4(SD_DET) (LCD_D7) PE13 | · · | PE12 (LCD_D6) | + * (MOSI)PA7 | · · | PB0(BTN_EN2) (LCD_D5) PE11 | · · | PE10 (LCD_D4) | + * (SD_SS)PA4 | · · | PC5(BTN_EN1) (LCD_RS) PE8 | · · | PE9 (LCD_EN) | + * (SCK)PA5 | · · | PA6(MISO) (BTN_ENC) PB1 | · · | PE7 (BEEPER) | + * ￣￣ ￣￣ | + * EXP2 EXP1 | + * --------------------------------------------------------------------------------------------- + */ +// +// LCDs and Controllers +// +#if HAS_SPI_LCD + #define BEEPER_PIN PE7 + #define BTN_ENC PB1 + + #if ENABLED(CR10_STOCKDISPLAY) + #define LCD_PINS_RS PE12 + + #define BTN_EN1 PE9 + #define BTN_EN2 PE10 + + #define LCD_PINS_ENABLE PE13 + #define LCD_PINS_D4 PE11 + + #else + + #define LCD_PINS_RS PE8 + + #define BTN_EN1 PC5 + #define BTN_EN2 PB0 + #define SD_DETECT_PIN PC4 + + #define LCD_SDSS PA4 + + #define LCD_PINS_ENABLE PE9 + #define LCD_PINS_D4 PE10 + + #if ENABLED(ULTIPANEL) + #define LCD_PINS_D5 PE11 + #define LCD_PINS_D6 PE12 + #define LCD_PINS_D7 PE13 + #endif + + #endif + + // Alter timing for graphical display + #if HAS_GRAPHICAL_LCD + #ifndef ST7920_DELAY_1 + #define ST7920_DELAY_1 DELAY_NS(96) + #endif + #ifndef ST7920_DELAY_2 + #define ST7920_DELAY_2 DELAY_NS(48) + #endif + #ifndef ST7920_DELAY_3 + #define ST7920_DELAY_3 DELAY_NS(600) + #endif + #endif + +#endif // HAS_SPI_LCD diff --git a/buildroot/share/PlatformIO/boards/BigTree_Btt002.json b/buildroot/share/PlatformIO/boards/BigTree_Btt002.json new file mode 100644 index 0000000000..95de3a6bcb --- /dev/null +++ b/buildroot/share/PlatformIO/boards/BigTree_Btt002.json @@ -0,0 +1,65 @@ +{ + "build": { + "core": "stm32", + "cpu": "cortex-m4", + "extra_flags": "-DSTM32F407xx", + "f_cpu": "168000000L", + "hwids": [ + [ + "0x1EAF", + "0x0003" + ], + [ + "0x0483", + "0x3748" + ] + ], + "ldscript": "stm32f407xg.ld", + "mcu": "stm32f407vet6", + "variant": "BIGTREE_GENERIC_STM32F407_5X" + }, + "debug": { + "jlink_device": "STM32F407VE", + "openocd_target": "stm32f4x", + "svd_path": "STM32F40x.svd", + "tools": { + "stlink": { + "server": { + "arguments": [ + "-f", + "scripts/interface/stlink.cfg", + "-c", + "transport select hla_swd", + "-f", + "scripts/target/stm32f4x.cfg", + "-c", + "reset_config none" + ], + "executable": "bin/openocd", + "package": "tool-openocd" + } + } + } + }, + "frameworks": [ + "arduino", + "stm32cube" + ], + "name": "STM32F407VE (64k RAM. 512k Flash)", + "upload": { + "disable_flushing": false, + "maximum_ram_size": 65536, + "maximum_size": 524288, + "protocol": "stlink", + "protocols": [ + "stlink", + "dfu", + "jlink" + ], + "require_upload_port": true, + "use_1200bps_touch": false, + "wait_for_upload_port": false + }, + "url": "http://www.st.com/en/microcontrollers/stm32f407zg.html", + "vendor": "Generic" +} diff --git a/buildroot/share/PlatformIO/variants/BIGTREE_GENERIC_STM32F407_5X/variant.cpp b/buildroot/share/PlatformIO/variants/BIGTREE_GENERIC_STM32F407_5X/variant.cpp index d21f5d7dd7..167fea510f 100644 --- a/buildroot/share/PlatformIO/variants/BIGTREE_GENERIC_STM32F407_5X/variant.cpp +++ b/buildroot/share/PlatformIO/variants/BIGTREE_GENERIC_STM32F407_5X/variant.cpp @@ -44,98 +44,100 @@ const PinName digitalPin[] = { PC_15, //D2 - OSC32_OUT PH_0, //D3 - OSC_IN PH_1, //D4 - OSC_OUT - PC_0, //D5 - 1: 2:ADC123_IN10 - PC_1, //D6 - 1: 2:ADC123_IN11 - PC_2, //D7 - 1:SPI2_MISO 2:ADC123_IN12 - PC_3, //D8 - 1:SPI2_MOSI 2:ADC123_IN13 - PA_0, //D9 - 1:UART4_TX / TIM5_CH1 2:ADC123_IN0 - PA_1, //D10 - 1:UART4_RX / TIM5_CH2 / TIM2_CH2 2:ADC123_IN1 - PA_2, //D11 - 1:USART2_TX /TIM5_CH3 / TIM9_CH1 / TIM2_CH3 2:ADC123_IN2 - PA_3, //D12 - 1:USART2_RX /TIM5_CH4 / TIM9_CH2 / TIM2_CH4 2:ADC123_IN3 - PA_4, //D13 - NOT FT 1:SPI1_NSS / SPI3_NSS / USART2_CK 2:ADC12_IN4 / DAC_OUT1 - PA_5, //D14 - NOT FT 1:SPI1_SCK 2:ADC12_IN5 / DAC_OUT2 - PA_6, //D15 - 1:SPI1_MISO / TIM13_CH1 / TIM3_CH1 2:ADC12_IN6 - PA_7, //D16 - 1:SPI1_MOSI / TIM14_CH1 / TIM3_CH2 2:ADC12_IN7 - PC_4, //D17 - 1: 2:ADC12_IN14 - PC_5, //D18 - 1: 2:ADC12_IN15 - PB_0, //D19 - 1:TIM3_CH3 2:ADC12_IN8 - PB_1, //D20 - 1:TIM3_CH4 2:ADC12_IN9 - PB_2, //D21 - BOOT1 - PB_10, //D22 - 1:SPI2_SCK / I2C2_SCL / USART3_TX / TIM2_CH3 - PB_11, //D23 - 1:I2C2_SDA / USART3_RX / TIM2_CH4 - PB_12, //D24 - 1:SPI2_NSS / OTG_HS_ID - PB_13, //D25 - 1:SPI2_SCK 2:OTG_HS_VBUS - PB_14, //D26 - 1:SPI2_MISO / TIM12_CH1 / OTG_HS_DM - PB_15, //D27 - SPI2_MOSI / TIM12_CH2 / OTG_HS_DP - PC_6, //D28 - 1:TIM8_CH1 / SDIO_D6 / USART6_TX / TIM3_CH1 - PC_7, //D29 - 1:TIM8_CH2 / SDIO_D7 / USART6_RX / TIM3_CH2 - PC_8, //D30 - 1:TIM8_CH3 / SDIO_D0 / TIM3_CH3 - PC_9, //D31 - 1:TIM8_CH4 / SDIO_D1 / TIM3_CH4 - PA_8, //D32 - 1:TIM1_CH1 / I2C3_SCL / OTG_FS_SOF - PA_9, //D33 - 1:USART1_TX / TIM1_CH2 2:OTG_FS_VBUS - PA_10, //34 - 1:USART1_RX / TIM1_CH3 / OTG_FS_ID - PA_11, //D35 - 1:TIM1_CH4 / OTG_FS_DM - PA_12, //D36 - 1:OTG_FS_DP - PA_13, //D37 - 0:JTMS-SWDIO - PA_14, //D38 - 0:JTCK-SWCLK - PA_15, //D39 - 0:JTDI 1:SPI3_NSS / SPI1_NSS - PC_10, //D40 - 1:UART4_TX / SPI3_SCK / SDIO_D2 / USART3_TX - PC_11, //D41 - 1:UART4_RX / SPI3_MISO / SDIO_D3 / USART3_RX - PC_12, //D42 - 1:UART5_TX / SPI3_MOSI / SDIO_CK - PD_2, //D43 - 1:UART5_RX / SDIO_CMD - PB_3, //D44 - 0:JTDO 1:SPI3_SCK / TIM2_CH2 / SPI1_SCK - PB_4, //D45 - 0:NJTRST 1:SPI3_MISO / TIM3_CH1 / SPI1_MISO - PB_5, //D45 - 1:TIM3_CH2 / SPI1_MOSI / SPI3_MOSI - PB_6, //D47 - 1:I2C1_SCL / TIM4_CH1 / USART1_TX - PB_7, //D48 - 1:I2C1_SDA / TIM4_CH2 / USART1_RX - PB_8, //D49 - 1:I2C1_SCL / TIM4_CH3 / SDIO_D4 / TIM10_CH1 - PB_9, //D50 - 1:I2C1_SDA / TIM4_CH4 / SDIO_D5 / TIM11_CH1 / SPI2_NSS + PB_2, //D5 - BOOT1 + PB_10, //D6 - 1:SPI2_SCK / I2C2_SCL / USART3_TX / TIM2_CH3 + PB_11, //D7 - 1:I2C2_SDA / USART3_RX / TIM2_CH4 + PB_12, //D8 - 1:SPI2_NSS / OTG_HS_ID + PB_13, //D9 - 1:SPI2_SCK 2:OTG_HS_VBUS + PB_14, //D10 - 1:SPI2_MISO / TIM12_CH1 / OTG_HS_DM + PB_15, //D11 - SPI2_MOSI / TIM12_CH2 / OTG_HS_DP + PC_6, //D12 - 1:TIM8_CH1 / SDIO_D6 / USART6_TX / TIM3_CH1 + PC_7, //D13 - 1:TIM8_CH2 / SDIO_D7 / USART6_RX / TIM3_CH2 + PC_8, //D14 - 1:TIM8_CH3 / SDIO_D0 / TIM3_CH3 + PC_9, //D15 - 1:TIM8_CH4 / SDIO_D1 / TIM3_CH4 + PA_8, //D16 - 1:TIM1_CH1 / I2C3_SCL / OTG_FS_SOF + PA_9, //D17 - 1:USART1_TX / TIM1_CH2 2:OTG_FS_VBUS + PA_10, //D18 - 1:USART1_RX / TIM1_CH3 / OTG_FS_ID + PA_11, //D19 - 1:TIM1_CH4 / OTG_FS_DM + PA_12, //D20 - 1:OTG_FS_DP + PA_13, //D21 - 0:JTMS-SWDIO + PA_14, //D22 - 0:JTCK-SWCLK + PA_15, //D23 - 0:JTDI 1:SPI3_NSS / SPI1_NSS + PC_10, //D24 - 1:UART4_TX / SPI3_SCK / SDIO_D2 / USART3_TX + PC_11, //D25 - 1:UART4_RX / SPI3_MISO / SDIO_D3 / USART3_RX + PC_12, //D26 - 1:UART5_TX / SPI3_MOSI / SDIO_CK + PD_2, //D27 - 1:UART5_RX / SDIO_CMD + PB_3, //D28 - 0:JTDO 1:SPI3_SCK / TIM2_CH2 / SPI1_SCK + PB_4, //D29 - 0:NJTRST 1:SPI3_MISO / TIM3_CH1 / SPI1_MISO + PB_5, //D30 - 1:TIM3_CH2 / SPI1_MOSI / SPI3_MOSI + PB_6, //D31 - 1:I2C1_SCL / TIM4_CH1 / USART1_TX + PB_7, //D32 - 1:I2C1_SDA / TIM4_CH2 / USART1_RX + PB_8, //D33 - 1:I2C1_SCL / TIM4_CH3 / SDIO_D4 / TIM10_CH1 + PB_9, //D34 - 1:I2C1_SDA / TIM4_CH4 / SDIO_D5 / TIM11_CH1 / SPI2_NSS + PA_0, //D35/A0 - 1:UART4_TX / TIM5_CH1 2:ADC123_IN0 + PA_1, //D36/A1 - 1:UART4_RX / TIM5_CH2 / TIM2_CH2 2:ADC123_IN1 + PA_2, //D37/A2 - 1:USART2_TX /TIM5_CH3 / TIM9_CH1 / TIM2_CH3 2:ADC123_IN2 + PA_3, //D38/A3 - 1:USART2_RX /TIM5_CH4 / TIM9_CH2 / TIM2_CH4 2:ADC123_IN3 + PA_4, //D39/A4 - NOT FT 1:SPI1_NSS / SPI3_NSS / USART2_CK 2:ADC12_IN4 / DAC_OUT1 + PA_5, //D40/A5 - NOT FT 1:SPI1_SCK 2:ADC12_IN5 / DAC_OUT2 + PA_6, //D41/A6 - 1:SPI1_MISO / TIM13_CH1 / TIM3_CH1 2:ADC12_IN6 + PA_7, //D42/A7 - 1:SPI1_MOSI / TIM14_CH1 / TIM3_CH2 2:ADC12_IN7 + PB_0, //D43/A8 - 1:TIM3_CH3 2:ADC12_IN8 + PB_1, //D44/A9 - 1:TIM3_CH4 2:ADC12_IN9 + PC_0, //D45/A10 - 1: 2:ADC123_IN10 + PC_1, //D46/A11 - 1: 2:ADC123_IN11 + PC_2, //D47/A12 - 1:SPI2_MISO 2:ADC123_IN12 + PC_3, //D48/A13 - 1:SPI2_MOSI 2:ADC123_IN13 + PC_4, //D49/A14 - 1: 2:ADC12_IN14 + PC_5, //D50/A15 - 1: 2:ADC12_IN15 + #if STM32F4X_PIN_NUM >= 144 + PF_3, //D51/A16 - 1:FSMC_A3 2:ADC3_IN9 + PF_4, //D52/A17 - 1:FSMC_A4 2:ADC3_IN14 + PF_5, //D53/A18 - 1:FSMC_A5 2:ADC3_IN15 + PF_6, //D54/A19 - 1:TIM10_CH1 2:ADC3_IN4 + PF_7, //D55/A20 - 1:TIM11_CH1 2:ADC3_IN5 + PF_8, //D56/A21 - 1:TIM13_CH1 2:ADC3_IN6 + PF_9, //D57/A22 - 1;TIM14_CH1 2:ADC3_IN7 + PF_10, //D58/A23 - 2:ADC3_IN8 + #endif #endif #if STM32F4X_PIN_NUM >= 100 //100 pins mcu, 82 gpio - PE_2, //D51 - 1:FSMC_A23 - PE_3, //D52 - 1:FSMC_A19 - PE_4, //D53 - 1:FSMC_A20 - PE_5, //D54 - 1:FSMC_A21 - PE_6, //D55 - 1:FSMC_A22 - PE_7, //D56 - 1:FSMC_D4 - PE_8, //D57 - 1:FSMC_D5 - PE_9, //D58 - 1:FSMC_D6 / TIM1_CH1 - PE_10, //D59 - 1:FSMC_D7 - PE_11, //D60 - 1:FSMC_D8 / TIM1_CH2 - PE_12, //D61 - 1:FSMC_D9 - PE_13, //D62 - 1:FSMC_D10 / TIM1_CH3 - PE_14, //D63 - 1:FSMC_D11 / TIM1_CH4 - PE_15, //D64 - 1:FSMC_D12 - PD_8, //D65 - 1:FSMC_D13 / USART3_TX - PD_9, //D66 - 1:FSMC_D14 / USART3_RX - PD_10, //D67 - 1:FSMC_D15 - PD_11, //D68 - 1:FSMC_A16 - PD_12, //D69 - 1:FSMC_A17 / TIM4_CH1 - PD_13, //D70 - 1:FSMC_A18 / TIM4_CH2 - PD_14, //D71 - 1:FSMC_D0 / TIM4_CH3 - PD_15, //D72 - 1:FSMC_D1 / TIM4_CH4 - PD_0, //D73 - 1:FSMC_D2 - PD_1, //D74 - 1:FSMC_D3 - PD_3, //D75 - 1:FSMC_CLK - PD_4, //D76 - 1:FSMC_NOE - PD_5, //D77 - 1:USART2_TX - PD_6, //D78 - 1:USART2_RX - PD_7, //D79 - PE_0, //D80 - PE_1, //D81 + PE_2, //D59 - 1:FSMC_A23 + PE_3, //D60 - 1:FSMC_A19 + PE_4, //D61 - 1:FSMC_A20 + PE_5, //D62 - 1:FSMC_A21 + PE_6, //D63 - 1:FSMC_A22 + PE_7, //D64 - 1:FSMC_D4 + PE_8, //D65 - 1:FSMC_D5 + PE_9, //D66 - 1:FSMC_D6 / TIM1_CH1 + PE_10, //D67 - 1:FSMC_D7 + PE_11, //D68 - 1:FSMC_D8 / TIM1_CH2 + PE_12, //D69 - 1:FSMC_D9 + PE_13, //D70 - 1:FSMC_D10 / TIM1_CH3 + PE_14, //D71 - 1:FSMC_D11 / TIM1_CH4 + PE_15, //D72 - 1:FSMC_D12 + PD_8, //D73 - 1:FSMC_D13 / USART3_TX + PD_9, //D74 - 1:FSMC_D14 / USART3_RX + PD_10, //D75 - 1:FSMC_D15 + PD_11, //D76 - 1:FSMC_A16 + PD_12, //D77 - 1:FSMC_A17 / TIM4_CH1 + PD_13, //D78 - 1:FSMC_A18 / TIM4_CH2 + PD_14, //D79 - 1:FSMC_D0 / TIM4_CH3 + PD_15, //D80 - 1:FSMC_D1 / TIM4_CH4 + PD_0, //D81 - 1:FSMC_D2 + PD_1, //D82 - 1:FSMC_D3 + PD_3, //D83 - 1:FSMC_CLK + PD_4, //D84 - 1:FSMC_NOE + PD_5, //D85 - 1:USART2_TX + PD_6, //D86 - 1:USART2_RX + PD_7, //D87 + PE_0, //D88 + PE_1, //D89 #endif #if STM32F4X_PIN_NUM >= 144 //144 pins mcu, 114 gpio - PF_0, //D82 - 1:FSMC_A0 / I2C2_SDA - PF_1, //D83 - 1:FSMC_A1 / I2C2_SCL - PF_2, //D84 - 1:FSMC_A2 - PF_3, //D85 - 1:FSMC_A3 2:ADC3_IN9 - PF_4, //D86 - 1:FSMC_A4 2:ADC3_IN14 - PF_5, //D87 - 1:FSMC_A5 2:ADC3_IN15 - PF_6, //D88 - 1:TIM10_CH1 2:ADC3_IN4 - PF_7, //D89 - 1:TIM11_CH1 2:ADC3_IN5 - PF_8, //D90 - 1:TIM13_CH1 2:ADC3_IN6 - PF_9, //D91 - 1;TIM14_CH1 2:ADC3_IN7 - PF_10, //D92 - 2:ADC3_IN8 + PF_0, //D90 - 1:FSMC_A0 / I2C2_SDA + PF_1, //D91 - 1:FSMC_A1 / I2C2_SCL + PF_2, //D92 - 1:FSMC_A2 PF_11, //D93 PF_12, //D94 - 1:FSMC_A6 PF_13, //D95 - 1:FSMC_A7 @@ -186,34 +188,6 @@ const PinName digitalPin[] = { PI_6, //D138 - 1:TIM8_CH2 PI_7, //D139 - 1:TIM8_CH3 #endif -#if STM32F4X_PIN_NUM >= 64 //64 pins mcu, 51 gpio, 16 ADC - PA_0, //D140/A0 = D9 - 1:UART4_TX / TIM5_CH1 2:ADC123_IN0 - PA_1, //D141/A1 = D10 - 1:UART4_RX / TIM5_CH2 / TIM2_CH2 2:ADC123_IN1 - PA_2, //D142/A2 = D11 - 1:USART2_TX /TIM5_CH3 / TIM9_CH1 / TIM2_CH3 2:ADC123_IN2 - PA_3, //D143/A3 = D12 - 1:USART2_RX /TIM5_CH4 / TIM9_CH2 / TIM2_CH4 2:ADC123_IN3 - PA_4, //D144/A4 = D13 - NOT FT 1:SPI1_NSS / SPI3_NSS / USART2_CK 2:ADC12_IN4 / DAC_OUT1 - PA_5, //D145/A5 = D14 - NOT FT 1:SPI1_SCK 2:ADC12_IN5 / DAC_OUT2 - PA_6, //D146/A6 = D15 - 1:SPI1_MISO / TIM13_CH1 / TIM3_CH1 2:ADC12_IN6 - PA_7, //D147/A7 = D16 - 1:SPI1_MOSI / TIM14_CH1 / TIM3_CH2 2:ADC12_IN7 - PB_0, //D148/A8 = D19 - 1:TIM3_CH3 2:ADC12_IN8 - PB_1, //D149/A9 = D20 - 1:TIM3_CH4 2:ADC12_IN9 - PC_0, //D150/A10 = D5 - 1: 2:ADC123_IN10 - PC_1, //D151/A11 = D6 - 1: 2:ADC123_IN11 - PC_2, //D152/A12 = D7 - 1:SPI2_MISO 2:ADC123_IN12 - PC_3, //D153/A13 = D8 - 1:SPI2_MOSI 2:ADC123_IN13 - PC_4, //D154/A14 = D17 - 1: 2:ADC12_IN14 - PC_5, //D155/A15 = D18 - 1: 2:ADC12_IN15 -#endif -#if STM32F4X_PIN_NUM >= 144 //144 pins mcu, 114 gpio, 24 ADC - PF_3, //D156/A16 = D85 - 1:FSMC_A3 2:ADC3_IN9 - PF_4, //D157/A17 = D86 - 1:FSMC_A4 2:ADC3_IN14 - PF_5, //D158/A18 = D87 - 1:FSMC_A5 2:ADC3_IN15 - PF_6, //D159/A19 = D88 - 1:TIM10_CH1 2:ADC3_IN4 - PF_7, //D160/A20 = D89 - 1:TIM11_CH1 2:ADC3_IN5 - PF_8, //D161/A21 = D90 - 1:TIM13_CH1 2:ADC3_IN6 - PF_9, //D162/A22 = D91 - 1;TIM14_CH1 2:ADC3_IN7 - PF_10, //D163/A23 = D92 - 2:ADC3_IN8 -#endif }; #ifdef __cplusplus diff --git a/buildroot/share/PlatformIO/variants/BIGTREE_GENERIC_STM32F407_5X/variant.h b/buildroot/share/PlatformIO/variants/BIGTREE_GENERIC_STM32F407_5X/variant.h index f6b9f7e4a4..44155d9b02 100644 --- a/buildroot/share/PlatformIO/variants/BIGTREE_GENERIC_STM32F407_5X/variant.h +++ b/buildroot/share/PlatformIO/variants/BIGTREE_GENERIC_STM32F407_5X/variant.h @@ -65,159 +65,161 @@ extern const PinName digitalPin[]; #if STM32F4X_PIN_NUM >= 64 //64 pins mcu, 51 gpio #define PC13 0 - #define PC14 1 //OSC32_IN - #define PC15 2 //OSC32_OUT - #define PH0 3 //OSC_IN - #define PH1 4 //OSC_OUT - #define PC0 5 //1: 2:ADC123_IN10 - #define PC1 6 //1: 2:ADC123_IN11 - #define PC2 7 //1:SPI2_MISO 2:ADC123_IN12 - #define PC3 8 //1:SPI2_MOSI 2:ADC123_IN13 - #define PA0 9 //1:UART4_TX / TIM5_CH1 2:ADC123_IN0 - #define PA1 10 //1:UART4_RX / TIM5_CH2 / TIM2_CH2 2:ADC123_IN1 - #define PA2 11 //1:USART2_TX /TIM5_CH3 / TIM9_CH1 / TIM2_CH3 2:ADC123_IN2 - #define PA3 12 //1:USART2_RX /TIM5_CH4 / TIM9_CH2 / TIM2_CH4 2:ADC123_IN3 - #define PA4 13 //NOT FT 1:SPI1_NSS / SPI3_NSS / USART2_CK 2:ADC12_IN4 / DAC_OUT1 - #define PA5 14 //NOT FT 1:SPI1_SCK 2:ADC12_IN5 / DAC_OUT2 - #define PA6 15 //1:SPI1_MISO / TIM13_CH1 / TIM3_CH1 2:ADC12_IN6 - #define PA7 16 //1:SPI1_MOSI / TIM14_CH1 / TIM3_CH2 2:ADC12_IN7 - #define PC4 17 //1: 2:ADC12_IN14 - #define PC5 18 //1: 2:ADC12_IN15 - #define PB0 19 //1:TIM3_CH3 2:ADC12_IN8 - #define PB1 20 //1:TIM3_CH4 2:ADC12_IN9 - #define PB2 21 //BOOT1 - #define PB10 22 //1:SPI2_SCK / I2C2_SCL / USART3_TX / TIM2_CH3 - #define PB11 23 //1:I2C2_SDA / USART3_RX / TIM2_CH4 - #define PB12 24 //1:SPI2_NSS / OTG_HS_ID - #define PB13 25 //1:SPI2_SCK 2:OTG_HS_VBUS - #define PB14 26 //1:SPI2_MISO / TIM12_CH1 / OTG_HS_DM - #define PB15 27 //SPI2_MOSI / TIM12_CH2 / OTG_HS_DP - #define PC6 28 //1:TIM8_CH1 / SDIO_D6 / USART6_TX / TIM3_CH1 - #define PC7 29 //1:TIM8_CH2 / SDIO_D7 / USART6_RX / TIM3_CH2 - #define PC8 30 //1:TIM8_CH3 / SDIO_D0 / TIM3_CH3 - #define PC9 31 //1:TIM8_CH4 / SDIO_D1 / TIM3_CH4 - #define PA8 32 //1:TIM1_CH1 / I2C3_SCL / OTG_FS_SOF - #define PA9 33 //1:USART1_TX / TIM1_CH2 2:OTG_FS_VBUS - #define PA10 34 //1:USART1_RX / TIM1_CH3 / OTG_FS_ID - #define PA11 35 //1:TIM1_CH4 / OTG_FS_DM - #define PA12 36 //1:OTG_FS_DP - #define PA13 37 //0:JTMS-SWDIO - #define PA14 38 //0:JTCK-SWCLK - #define PA15 39 //0:JTDI 1:SPI3_NSS / SPI1_NSS - #define PC10 40 //1:UART4_TX / SPI3_SCK / SDIO_D2 / USART3_TX - #define PC11 41 //1:UART4_RX / SPI3_MISO / SDIO_D3 / USART3_RX - #define PC12 42 //1:UART5_TX / SPI3_MOSI / SDIO_CK - #define PD2 43 //1:UART5_RX / SDIO_CMD - #define PB3 44 //0:JTDO 1:SPI3_SCK / TIM2_CH2 / SPI1_SCK - #define PB4 45 //0:NJTRST 1:SPI3_MISO / TIM3_CH1 / SPI1_MISO - #define PB5 46 //1:TIM3_CH2 / SPI1_MOSI / SPI3_MOSI - #define PB6 47 //1:I2C1_SCL / TIM4_CH1 / USART1_TX - #define PB7 48 //1:I2C1_SDA / TIM4_CH2 / USART1_RX - #define PB8 49 //1:I2C1_SCL / TIM4_CH3 / SDIO_D4 / TIM10_CH1 - #define PB9 50 //1:I2C1_SDA / TIM4_CH4 / SDIO_D5 / TIM11_CH1 / SPI2_NSS + #define PC14 1 //OSC32_IN + #define PC15 2 //OSC32_OUT + #define PH0 3 //OSC_IN + #define PH1 4 //OSC_OUT + #define PB2 5 //BOOT1 + #define PB10 6 //1:SPI2_SCK / I2C2_SCL / USART3_TX / TIM2_CH3 + #define PB11 7 //1:I2C2_SDA / USART3_RX / TIM2_CH4 + #define PB12 8 //1:SPI2_NSS / OTG_HS_ID + #define PB13 9 //1:SPI2_SCK 2:OTG_HS_VBUS + #define PB14 10 //1:SPI2_MISO / TIM12_CH1 / OTG_HS_DM + #define PB15 11 //SPI2_MOSI / TIM12_CH2 / OTG_HS_DP + #define PC6 12 //1:TIM8_CH1 / SDIO_D6 / USART6_TX / TIM3_CH1 + #define PC7 13 //1:TIM8_CH2 / SDIO_D7 / USART6_RX / TIM3_CH2 + #define PC8 14 //1:TIM8_CH3 / SDIO_D0 / TIM3_CH3 + #define PC9 15 //1:TIM8_CH4 / SDIO_D1 / TIM3_CH4 + #define PA8 16 //1:TIM1_CH1 / I2C3_SCL / OTG_FS_SOF + #define PA9 17 //1:USART1_TX / TIM1_CH2 2:OTG_FS_VBUS + #define PA10 18 //1:USART1_RX / TIM1_CH3 / OTG_FS_ID + #define PA11 19 //1:TIM1_CH4 / OTG_FS_DM + #define PA12 20 //1:OTG_FS_DP + #define PA13 21 //0:JTMS-SWDIO + #define PA14 22 //0:JTCK-SWCLK + #define PA15 23 //0:JTDI 1:SPI3_NSS / SPI1_NSS + #define PC10 24 //1:UART4_TX / SPI3_SCK / SDIO_D2 / USART3_TX + #define PC11 25 //1:UART4_RX / SPI3_MISO / SDIO_D3 / USART3_RX + #define PC12 26 //1:UART5_TX / SPI3_MOSI / SDIO_CK + #define PD2 27 //1:UART5_RX / SDIO_CMD + #define PB3 28 //0:JTDO 1:SPI3_SCK / TIM2_CH2 / SPI1_SCK + #define PB4 29 //0:NJTRST 1:SPI3_MISO / TIM3_CH1 / SPI1_MISO + #define PB5 30 //1:TIM3_CH2 / SPI1_MOSI / SPI3_MOSI + #define PB6 31 //1:I2C1_SCL / TIM4_CH1 / USART1_TX + #define PB7 32 //1:I2C1_SDA / TIM4_CH2 / USART1_RX + #define PB8 33 //1:I2C1_SCL / TIM4_CH3 / SDIO_D4 / TIM10_CH1 + #define PB9 34 //1:I2C1_SDA / TIM4_CH4 / SDIO_D5 / TIM11_CH1 / SPI2_NSS + #define PA0 35 //1:UART4_TX / TIM5_CH1 2:ADC123_IN0 + #define PA1 36 //1:UART4_RX / TIM5_CH2 / TIM2_CH2 2:ADC123_IN1 + #define PA2 37 //1:USART2_TX /TIM5_CH3 / TIM9_CH1 / TIM2_CH3 2:ADC123_IN2 + #define PA3 38 //1:USART2_RX /TIM5_CH4 / TIM9_CH2 / TIM2_CH4 2:ADC123_IN3 + #define PA4 39 //NOT FT 1:SPI1_NSS / SPI3_NSS / USART2_CK 2:ADC12_IN4 / DAC_OUT1 + #define PA5 40 //NOT FT 1:SPI1_SCK 2:ADC12_IN5 / DAC_OUT2 + #define PA6 41 //1:SPI1_MISO / TIM13_CH1 / TIM3_CH1 2:ADC12_IN6 + #define PA7 42 //1:SPI1_MOSI / TIM14_CH1 / TIM3_CH2 2:ADC12_IN7 + #define PB0 43 //1:TIM3_CH3 2:ADC12_IN8 + #define PB1 44 //1:TIM3_CH4 2:ADC12_IN9 + #define PC0 45 //1: 2:ADC123_IN10 + #define PC1 46 //1: 2:ADC123_IN11 + #define PC2 47 //1:SPI2_MISO 2:ADC123_IN12 + #define PC3 48 //1:SPI2_MOSI 2:ADC123_IN13 + #define PC4 49 //1: 2:ADC12_IN14 + #define PC5 50 //1: 2:ADC12_IN15 + #if STM32F4X_PIN_NUM >= 144 + #define PF3 51 //1:FSMC_A3 2:ADC3_IN9 + #define PF4 52 //1:FSMC_A4 2:ADC3_IN14 + #define PF5 53 //1:FSMC_A5 2:ADC3_IN15 + #define PF6 54 //1:TIM10_CH1 2:ADC3_IN4 + #define PF7 55 //1:TIM11_CH1 2:ADC3_IN5 + #define PF8 56 //1:TIM13_CH1 2:ADC3_IN6 + #define PF9 57 //1;TIM14_CH1 2:ADC3_IN7 + #define PF10 58 //2:ADC3_IN8 + #endif #endif #if STM32F4X_PIN_NUM >= 100 //100 pins mcu, 82 gpio - #define PE2 51 //1:FSMC_A23 - #define PE3 52 //1:FSMC_A19 - #define PE4 53 //1:FSMC_A20 - #define PE5 54 //1:FSMC_A21 - #define PE6 55 //1:FSMC_A22 - #define PE7 56 //1:FSMC_D4 - #define PE8 57 //1:FSMC_D5 - #define PE9 58 //1:FSMC_D6 / TIM1_CH1 - #define PE10 59 //1:FSMC_D7 - #define PE11 60 //1:FSMC_D8 / TIM1_CH2 - #define PE12 61 //1:FSMC_D9 - #define PE13 62 //1:FSMC_D10 / TIM1_CH3 - #define PE14 63 //1:FSMC_D11 / TIM1_CH4 - #define PE15 64 //1:FSMC_D12 - #define PD8 65 //1:FSMC_D13 / USART3_TX - #define PD9 66 //1:FSMC_D14 / USART3_RX - #define PD10 67 //1:FSMC_D15 - #define PD11 68 //1:FSMC_A16 - #define PD12 69 //1:FSMC_A17 / TIM4_CH1 - #define PD13 70 //1:FSMC_A18 / TIM4_CH2 - #define PD14 71 //1:FSMC_D0 / TIM4_CH3 - #define PD15 72 //1:FSMC_D1 / TIM4_CH4 - #define PD0 73 //1:FSMC_D2 - #define PD1 74 //1:FSMC_D3 - #define PD3 75 //1:FSMC_CLK - #define PD4 76 //1:FSMC_NOE - #define PD5 77 //1:USART2_TX - #define PD6 78 //1:USART2_RX - #define PD7 79 - #define PE0 80 - #define PE1 81 + #define PE2 (35+STM32F4X_ADC_NUM) //1:FSMC_A23 + #define PE3 (36+STM32F4X_ADC_NUM) //1:FSMC_A19 + #define PE4 (37+STM32F4X_ADC_NUM) //1:FSMC_A20 + #define PE5 (38+STM32F4X_ADC_NUM) //1:FSMC_A21 + #define PE6 (39+STM32F4X_ADC_NUM) //1:FSMC_A22 + #define PE7 (40+STM32F4X_ADC_NUM) //1:FSMC_D4 + #define PE8 (41+STM32F4X_ADC_NUM) //1:FSMC_D5 + #define PE9 (42+STM32F4X_ADC_NUM) //1:FSMC_D6 / TIM1_CH1 + #define PE10 (43+STM32F4X_ADC_NUM) //1:FSMC_D7 + #define PE11 (44+STM32F4X_ADC_NUM) //1:FSMC_D8 / TIM1_CH2 + #define PE12 (45+STM32F4X_ADC_NUM) //1:FSMC_D9 + #define PE13 (46+STM32F4X_ADC_NUM) //1:FSMC_D10 / TIM1_CH3 + #define PE14 (47+STM32F4X_ADC_NUM) //1:FSMC_D11 / TIM1_CH4 + #define PE15 (48+STM32F4X_ADC_NUM) //1:FSMC_D12 + #define PD8 (49+STM32F4X_ADC_NUM) //1:FSMC_D13 / USART3_TX + #define PD9 (50+STM32F4X_ADC_NUM) //1:FSMC_D14 / USART3_RX + #define PD10 (51+STM32F4X_ADC_NUM) //1:FSMC_D15 + #define PD11 (52+STM32F4X_ADC_NUM) //1:FSMC_A16 + #define PD12 (53+STM32F4X_ADC_NUM) //1:FSMC_A17 / TIM4_CH1 + #define PD13 (54+STM32F4X_ADC_NUM) //1:FSMC_A18 / TIM4_CH2 + #define PD14 (55+STM32F4X_ADC_NUM) //1:FSMC_D0 / TIM4_CH3 + #define PD15 (56+STM32F4X_ADC_NUM) //1:FSMC_D1 / TIM4_CH4 + #define PD0 (57+STM32F4X_ADC_NUM) //1:FSMC_D2 + #define PD1 (58+STM32F4X_ADC_NUM) //1:FSMC_D3 + #define PD3 (59+STM32F4X_ADC_NUM) //1:FSMC_CLK + #define PD4 (60+STM32F4X_ADC_NUM) //1:FSMC_NOE + #define PD5 (61+STM32F4X_ADC_NUM) //1:USART2_TX + #define PD6 (62+STM32F4X_ADC_NUM) //1:USART2_RX + #define PD7 (63+STM32F4X_ADC_NUM) + #define PE0 (64+STM32F4X_ADC_NUM) + #define PE1 (65+STM32F4X_ADC_NUM) #endif #if STM32F4X_PIN_NUM >= 144 //144 pins mcu, 114 gpio - #define PF0 82 //1:FSMC_A0 / I2C2_SDA - #define PF1 83 //1:FSMC_A1 / I2C2_SCL - #define PF2 84 //1:FSMC_A2 - #define PF3 85 //1:FSMC_A3 2:ADC3_IN9 - #define PF4 86 //1:FSMC_A4 2:ADC3_IN14 - #define PF5 87 //1:FSMC_A5 2:ADC3_IN15 - #define PF6 88 //1:TIM10_CH1 2:ADC3_IN4 - #define PF7 89 //1:TIM11_CH1 2:ADC3_IN5 - #define PF8 90 //1:TIM13_CH1 2:ADC3_IN6 - #define PF9 91 //1;TIM14_CH1 2:ADC3_IN7 - #define PF10 92 //2:ADC3_IN8 - #define PF11 93 - #define PF12 94 //1:FSMC_A6 - #define PF13 95 //1:FSMC_A7 - #define PF14 96 //1:FSMC_A8 - #define PF15 97 //1:FSMC_A9 - #define PG0 98 //1:FSMC_A10 - #define PG1 99 //1:FSMC_A11 - #define PG2 100 //1:FSMC_A12 - #define PG3 101 //1:FSMC_A13 - #define PG4 102 //1:FSMC_A14 - #define PG5 103 //1:FSMC_A15 - #define PG6 104 - #define PG7 105 - #define PG8 106 - #define PG9 107 //1:USART6_RX - #define PG10 108 //1:FSMC_NE3 - #define PG11 109 - #define PG12 110 //1:FSMC_NE4 - #define PG13 111 //1:FSMC_A24 - #define PG14 112 //1:FSMC_A25 / USART6_TX - #define PG15 113 + #define PF0 (66+STM32F4X_ADC_NUM) //1:FSMC_A0 / I2C2_SDA + #define PF1 (67+STM32F4X_ADC_NUM) //1:FSMC_A1 / I2C2_SCL + #define PF2 (68+STM32F4X_ADC_NUM) //1:FSMC_A2 + #define PF11 (69+STM32F4X_ADC_NUM) + #define PF12 (70+STM32F4X_ADC_NUM) //1:FSMC_A6 + #define PF13 (71+STM32F4X_ADC_NUM) //1:FSMC_A7 + #define PF14 (72+STM32F4X_ADC_NUM) //1:FSMC_A8 + #define PF15 (73+STM32F4X_ADC_NUM) //1:FSMC_A9 + #define PG0 (74+STM32F4X_ADC_NUM) //1:FSMC_A10 + #define PG1 (75+STM32F4X_ADC_NUM) //1:FSMC_A11 + #define PG2 (76+STM32F4X_ADC_NUM) //1:FSMC_A12 + #define PG3 (77+STM32F4X_ADC_NUM) //1:FSMC_A13 + #define PG4 (78+STM32F4X_ADC_NUM) //1:FSMC_A14 + #define PG5 (79+STM32F4X_ADC_NUM) //1:FSMC_A15 + #define PG6 (80+STM32F4X_ADC_NUM) + #define PG7 (81+STM32F4X_ADC_NUM) + #define PG8 (82+STM32F4X_ADC_NUM) + #define PG9 (83+STM32F4X_ADC_NUM) //1:USART6_RX + #define PG10 (84+STM32F4X_ADC_NUM) //1:FSMC_NE3 + #define PG11 (85+STM32F4X_ADC_NUM) + #define PG12 (86+STM32F4X_ADC_NUM) //1:FSMC_NE4 + #define PG13 (87+STM32F4X_ADC_NUM) //1:FSMC_A24 + #define PG14 (88+STM32F4X_ADC_NUM) //1:FSMC_A25 / USART6_TX + #define PG15 (89+STM32F4X_ADC_NUM) #endif #if STM32F4X_PIN_NUM >= 176 //176 pins mcu, 140 gpio - #define PI8 114 - #define PI9 115 - #define PI10 116 - #define PI11 117 - #define PH2 118 - #define PH3 119 - #define PH4 120 //1:I2C2_SCL - #define PH5 121 //1:I2C2_SDA - #define PH6 122 //1:TIM12_CH1 - #define PH7 123 //1:I2C3_SCL - #define PH8 124 //1:I2C3_SDA - #define PH9 125 //1:TIM12_CH2 - #define PH10 126 //1:TIM5_CH1 - #define PH11 127 //1:TIM5_CH2 - #define PH12 128 //1:TIM5_CH3 - #define PH13 129 - #define PH14 130 - #define PH15 131 - #define PI0 132 //1:TIM5_CH4 / SPI2_NSS - #define PI1 133 //1:SPI2_SCK - #define PI2 134 //1:TIM8_CH4 /SPI2_MISO - #define PI3 135 //1:SPI2_MOS - #define PI4 136 - #define PI5 137 //1:TIM8_CH1 - #define PI6 138 //1:TIM8_CH2 - #define PI7 139 //1:TIM8_CH3 + #define PI8 (90+STM32F4X_ADC_NUM) + #define PI9 (91+STM32F4X_ADC_NUM) + #define PI10 (92+STM32F4X_ADC_NUM) + #define PI11 (93+STM32F4X_ADC_NUM) + #define PH2 (94+STM32F4X_ADC_NUM) + #define PH3 (95+STM32F4X_ADC_NUM) + #define PH4 (96+STM32F4X_ADC_NUM) //1:I2C2_SCL + #define PH5 (97+STM32F4X_ADC_NUM) //1:I2C2_SDA + #define PH6 (98+STM32F4X_ADC_NUM) //1:TIM12_CH1 + #define PH7 (99+STM32F4X_ADC_NUM) //1:I2C3_SCL + #define PH8 (100+STM32F4X_ADC_NUM) //1:I2C3_SDA + #define PH9 (101+STM32F4X_ADC_NUM) //1:TIM12_CH2 + #define PH10 (102+STM32F4X_ADC_NUM) //1:TIM5_CH1 + #define PH11 (103+STM32F4X_ADC_NUM) //1:TIM5_CH2 + #define PH12 (104+STM32F4X_ADC_NUM) //1:TIM5_CH3 + #define PH13 (105+STM32F4X_ADC_NUM) + #define PH14 (106+STM32F4X_ADC_NUM) + #define PH15 (107+STM32F4X_ADC_NUM) + #define PI0 (108+STM32F4X_ADC_NUM) //1:TIM5_CH4 / SPI2_NSS + #define PI1 (109+STM32F4X_ADC_NUM) //1:SPI2_SCK + #define PI2 (110+STM32F4X_ADC_NUM) //1:TIM8_CH4 /SPI2_MISO + #define PI3 (111+STM32F4X_ADC_NUM) //1:SPI2_MOS + #define PI4 (112+STM32F4X_ADC_NUM) + #define PI5 (113+STM32F4X_ADC_NUM) //1:TIM8_CH1 + #define PI6 (114+STM32F4X_ADC_NUM) //1:TIM8_CH2 + #define PI7 (115+STM32F4X_ADC_NUM) //1:TIM8_CH3 #endif // This must be a literal -#define NUM_DIGITAL_PINS (STM32F4X_GPIO_NUM + STM32F4X_ADC_NUM) +#define NUM_DIGITAL_PINS (STM32F4X_GPIO_NUM) // This must be a literal with a value less than or equal to MAX_ANALOG_INPUTS #define NUM_ANALOG_INPUTS (STM32F4X_ADC_NUM) -#define NUM_ANALOG_FIRST (STM32F4X_GPIO_NUM) +#define NUM_ANALOG_FIRST 35 // Below ADC, DAC and PWM definitions already done in the core // Could be redefined here if needed diff --git a/config/default/Configuration.h b/config/default/Configuration.h index 90b1802576..7a1111fde3 100644 --- a/config/default/Configuration.h +++ b/config/default/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 diff --git a/config/default/Configuration_adv.h b/config/default/Configuration_adv.h index 625c8d259d..45e445e122 100644 --- a/config/default/Configuration_adv.h +++ b/config/default/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/3DFabXYZ/Migbot/Configuration.h b/config/examples/3DFabXYZ/Migbot/Configuration.h index 6a6578b159..af619a56a4 100644 --- a/config/examples/3DFabXYZ/Migbot/Configuration.h +++ b/config/examples/3DFabXYZ/Migbot/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2068,7 +2069,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h index d73e3b2df2..75699df8f0 100644 --- a/config/examples/3DFabXYZ/Migbot/Configuration_adv.h +++ b/config/examples/3DFabXYZ/Migbot/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + #define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/AlephObjects/TAZ4/Configuration.h b/config/examples/AlephObjects/TAZ4/Configuration.h index 2b2b8c72de..1b7b43c837 100644 --- a/config/examples/AlephObjects/TAZ4/Configuration.h +++ b/config/examples/AlephObjects/TAZ4/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 7 #define TEMP_SENSOR_1 0 @@ -2057,7 +2058,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/AlephObjects/TAZ4/Configuration_adv.h b/config/examples/AlephObjects/TAZ4/Configuration_adv.h index 9733d47283..54404c21fd 100644 --- a/config/examples/AlephObjects/TAZ4/Configuration_adv.h +++ b/config/examples/AlephObjects/TAZ4/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Alfawise/U20/Configuration.h b/config/examples/Alfawise/U20/Configuration.h index 2a85f6437f..f0c135129f 100644 --- a/config/examples/Alfawise/U20/Configuration.h +++ b/config/examples/Alfawise/U20/Configuration.h @@ -409,6 +409,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -452,7 +453,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2127,7 +2128,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Alfawise/U20/Configuration_adv.h b/config/examples/Alfawise/U20/Configuration_adv.h index e76095de66..73c219a9a8 100644 --- a/config/examples/Alfawise/U20/Configuration_adv.h +++ b/config/examples/Alfawise/U20/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + #define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/AliExpress/CL-260/Configuration.h b/config/examples/AliExpress/CL-260/Configuration.h index 70446ed7b3..c1312b403a 100644 --- a/config/examples/AliExpress/CL-260/Configuration.h +++ b/config/examples/AliExpress/CL-260/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2037,7 +2038,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/AliExpress/UM2pExt/Configuration.h b/config/examples/AliExpress/UM2pExt/Configuration.h index de2d707c75..dfe21131f0 100644 --- a/config/examples/AliExpress/UM2pExt/Configuration.h +++ b/config/examples/AliExpress/UM2pExt/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 20 #define TEMP_SENSOR_1 20 @@ -2048,7 +2049,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/AliExpress/UM2pExt/Configuration_adv.h b/config/examples/AliExpress/UM2pExt/Configuration_adv.h index 5be01234df..4e72255df9 100644 --- a/config/examples/AliExpress/UM2pExt/Configuration_adv.h +++ b/config/examples/AliExpress/UM2pExt/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + #define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Anet/A2/Configuration.h b/config/examples/Anet/A2/Configuration.h index 910955ab85..cc07912b35 100644 --- a/config/examples/Anet/A2/Configuration.h +++ b/config/examples/Anet/A2/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -2039,7 +2040,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Anet/A2/Configuration_adv.h b/config/examples/Anet/A2/Configuration_adv.h index c74889b5b7..daf8c79723 100644 --- a/config/examples/Anet/A2/Configuration_adv.h +++ b/config/examples/Anet/A2/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Anet/A2plus/Configuration.h b/config/examples/Anet/A2plus/Configuration.h index 749644ef7f..f393c886dc 100644 --- a/config/examples/Anet/A2plus/Configuration.h +++ b/config/examples/Anet/A2plus/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -2039,7 +2040,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Anet/A2plus/Configuration_adv.h b/config/examples/Anet/A2plus/Configuration_adv.h index c74889b5b7..daf8c79723 100644 --- a/config/examples/Anet/A2plus/Configuration_adv.h +++ b/config/examples/Anet/A2plus/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Anet/A6/Configuration.h b/config/examples/Anet/A6/Configuration.h index 3155687958..a201a85439 100644 --- a/config/examples/Anet/A6/Configuration.h +++ b/config/examples/Anet/A6/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 11 #define TEMP_SENSOR_1 0 @@ -2190,7 +2191,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Anet/A6/Configuration_adv.h b/config/examples/Anet/A6/Configuration_adv.h index 07fec38958..74f54f24c8 100644 --- a/config/examples/Anet/A6/Configuration_adv.h +++ b/config/examples/Anet/A6/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Anet/A8/Configuration.h b/config/examples/Anet/A8/Configuration.h index 7f3ae8fa22..f67c3797c0 100644 --- a/config/examples/Anet/A8/Configuration.h +++ b/config/examples/Anet/A8/Configuration.h @@ -360,6 +360,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -403,7 +404,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -2052,7 +2053,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Anet/A8/Configuration_adv.h b/config/examples/Anet/A8/Configuration_adv.h index 04f1669536..b421f1c919 100644 --- a/config/examples/Anet/A8/Configuration_adv.h +++ b/config/examples/Anet/A8/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Anet/A8plus/Configuration.h b/config/examples/Anet/A8plus/Configuration.h index 24393d5ce3..8d64b038da 100644 --- a/config/examples/Anet/A8plus/Configuration.h +++ b/config/examples/Anet/A8plus/Configuration.h @@ -360,6 +360,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -403,7 +404,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -2048,7 +2049,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Anet/A8plus/Configuration_adv.h b/config/examples/Anet/A8plus/Configuration_adv.h index 836dfd7119..0657080c8e 100644 --- a/config/examples/Anet/A8plus/Configuration_adv.h +++ b/config/examples/Anet/A8plus/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Anet/E16/Configuration.h b/config/examples/Anet/E16/Configuration.h index c5a3aeb61f..e92c834ac5 100644 --- a/config/examples/Anet/E16/Configuration.h +++ b/config/examples/Anet/E16/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -2049,7 +2050,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Anet/E16/Configuration_adv.h b/config/examples/Anet/E16/Configuration_adv.h index 8841088c32..a5ef5fd6a9 100644 --- a/config/examples/Anet/E16/Configuration_adv.h +++ b/config/examples/Anet/E16/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + #define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/AnyCubic/i3/Configuration.h b/config/examples/AnyCubic/i3/Configuration.h index 3d589d57ce..f72d0ab332 100644 --- a/config/examples/AnyCubic/i3/Configuration.h +++ b/config/examples/AnyCubic/i3/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2047,7 +2048,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/AnyCubic/i3/Configuration_adv.h b/config/examples/AnyCubic/i3/Configuration_adv.h index 6940eea295..4e22f2a6d0 100644 --- a/config/examples/AnyCubic/i3/Configuration_adv.h +++ b/config/examples/AnyCubic/i3/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/ArmEd/Configuration.h b/config/examples/ArmEd/Configuration.h index 7b7f35e678..27556db668 100644 --- a/config/examples/ArmEd/Configuration.h +++ b/config/examples/ArmEd/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -2038,7 +2039,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/ArmEd/Configuration_adv.h b/config/examples/ArmEd/Configuration_adv.h index ad154eb2d5..28684f0a55 100644 --- a/config/examples/ArmEd/Configuration_adv.h +++ b/config/examples/ArmEd/Configuration_adv.h @@ -662,10 +662,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -855,11 +855,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -884,23 +905,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -935,6 +939,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Azteeg/X5GT/Configuration.h b/config/examples/Azteeg/X5GT/Configuration.h index 8150eb1e75..66c4d55ff5 100644 --- a/config/examples/Azteeg/X5GT/Configuration.h +++ b/config/examples/Azteeg/X5GT/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 1 @@ -2037,7 +2038,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration.h b/config/examples/BIBO/TouchX/cyclops/Configuration.h index 4996ed7289..ea7b87e5c8 100644 --- a/config/examples/BIBO/TouchX/cyclops/Configuration.h +++ b/config/examples/BIBO/TouchX/cyclops/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -2037,7 +2038,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h index 1e67a98e2e..97ed75e160 100644 --- a/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h +++ b/config/examples/BIBO/TouchX/cyclops/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/BIBO/TouchX/default/Configuration.h b/config/examples/BIBO/TouchX/default/Configuration.h index 1ccc892b77..ee10b070d9 100644 --- a/config/examples/BIBO/TouchX/default/Configuration.h +++ b/config/examples/BIBO/TouchX/default/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 5 @@ -2037,7 +2038,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/BIBO/TouchX/default/Configuration_adv.h b/config/examples/BIBO/TouchX/default/Configuration_adv.h index 05b8382b4b..f1238222e0 100644 --- a/config/examples/BIBO/TouchX/default/Configuration_adv.h +++ b/config/examples/BIBO/TouchX/default/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/BQ/Hephestos/Configuration.h b/config/examples/BQ/Hephestos/Configuration.h index 398878ef47..06aad85036 100644 --- a/config/examples/BQ/Hephestos/Configuration.h +++ b/config/examples/BQ/Hephestos/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2025,7 +2026,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/BQ/Hephestos/Configuration_adv.h b/config/examples/BQ/Hephestos/Configuration_adv.h index e14111b787..e3a39d4336 100644 --- a/config/examples/BQ/Hephestos/Configuration_adv.h +++ b/config/examples/BQ/Hephestos/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/BQ/Hephestos_2/Configuration.h b/config/examples/BQ/Hephestos_2/Configuration.h index 4b2d45e339..806efae751 100644 --- a/config/examples/BQ/Hephestos_2/Configuration.h +++ b/config/examples/BQ/Hephestos_2/Configuration.h @@ -367,6 +367,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -410,7 +411,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 70 #define TEMP_SENSOR_1 0 @@ -2037,7 +2038,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/BQ/Hephestos_2/Configuration_adv.h b/config/examples/BQ/Hephestos_2/Configuration_adv.h index 20c1a8f0e3..242f6bda6b 100644 --- a/config/examples/BQ/Hephestos_2/Configuration_adv.h +++ b/config/examples/BQ/Hephestos_2/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -859,11 +859,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -888,23 +909,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -939,6 +943,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/BQ/WITBOX/Configuration.h b/config/examples/BQ/WITBOX/Configuration.h index 6ac8b734ec..55544b04a1 100644 --- a/config/examples/BQ/WITBOX/Configuration.h +++ b/config/examples/BQ/WITBOX/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2025,7 +2026,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/BQ/WITBOX/Configuration_adv.h b/config/examples/BQ/WITBOX/Configuration_adv.h index e14111b787..e3a39d4336 100644 --- a/config/examples/BQ/WITBOX/Configuration_adv.h +++ b/config/examples/BQ/WITBOX/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Cartesio/Configuration.h b/config/examples/Cartesio/Configuration.h index 8f93e8fbbe..f4d8e167ab 100644 --- a/config/examples/Cartesio/Configuration.h +++ b/config/examples/Cartesio/Configuration.h @@ -360,6 +360,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -403,7 +404,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 -1 #define TEMP_SENSOR_1 -1 @@ -2036,7 +2037,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Cartesio/Configuration_adv.h b/config/examples/Cartesio/Configuration_adv.h index 9100aba87d..9b22210c3e 100644 --- a/config/examples/Cartesio/Configuration_adv.h +++ b/config/examples/Cartesio/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Creality/CR-10/Configuration.h b/config/examples/Creality/CR-10/Configuration.h index 45c4793708..e538cdd414 100644 --- a/config/examples/Creality/CR-10/Configuration.h +++ b/config/examples/Creality/CR-10/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2047,7 +2048,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Creality/CR-10/Configuration_adv.h b/config/examples/Creality/CR-10/Configuration_adv.h index dd7e9498e5..96b3399880 100644 --- a/config/examples/Creality/CR-10/Configuration_adv.h +++ b/config/examples/Creality/CR-10/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Creality/CR-10S/Configuration.h b/config/examples/Creality/CR-10S/Configuration.h index a8556daa96..f4cbe652ae 100644 --- a/config/examples/Creality/CR-10S/Configuration.h +++ b/config/examples/Creality/CR-10S/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2038,7 +2039,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Creality/CR-10S/Configuration_adv.h b/config/examples/Creality/CR-10S/Configuration_adv.h index ebbea24d46..f6ce2b7c24 100644 --- a/config/examples/Creality/CR-10S/Configuration_adv.h +++ b/config/examples/Creality/CR-10S/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + #define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Creality/CR-10_5S/Configuration.h b/config/examples/Creality/CR-10_5S/Configuration.h index 1be716c2f3..833988af1e 100644 --- a/config/examples/Creality/CR-10_5S/Configuration.h +++ b/config/examples/Creality/CR-10_5S/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2040,7 +2041,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Creality/CR-10_5S/Configuration_adv.h b/config/examples/Creality/CR-10_5S/Configuration_adv.h index 13c702627d..aa0b478092 100644 --- a/config/examples/Creality/CR-10_5S/Configuration_adv.h +++ b/config/examples/Creality/CR-10_5S/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + #define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Creality/CR-10mini/Configuration.h b/config/examples/Creality/CR-10mini/Configuration.h index 8ecb7f3a1b..e32a3fef9b 100644 --- a/config/examples/Creality/CR-10mini/Configuration.h +++ b/config/examples/Creality/CR-10mini/Configuration.h @@ -368,6 +368,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -411,7 +412,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2056,7 +2057,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Creality/CR-10mini/Configuration_adv.h b/config/examples/Creality/CR-10mini/Configuration_adv.h index 9a23015ff5..29316bcdd6 100644 --- a/config/examples/Creality/CR-10mini/Configuration_adv.h +++ b/config/examples/Creality/CR-10mini/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + #define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Creality/CR-20 Pro/Configuration.h b/config/examples/Creality/CR-20 Pro/Configuration.h index 90e232096e..8e8c0f7756 100644 --- a/config/examples/Creality/CR-20 Pro/Configuration.h +++ b/config/examples/Creality/CR-20 Pro/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2040,7 +2041,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Creality/CR-20 Pro/Configuration_adv.h b/config/examples/Creality/CR-20 Pro/Configuration_adv.h index 97a2b5dd5d..013c3f6397 100644 --- a/config/examples/Creality/CR-20 Pro/Configuration_adv.h +++ b/config/examples/Creality/CR-20 Pro/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + #define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Creality/CR-20/Configuration.h b/config/examples/Creality/CR-20/Configuration.h index 0e782bc3a1..66dbf6fbc3 100644 --- a/config/examples/Creality/CR-20/Configuration.h +++ b/config/examples/Creality/CR-20/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2040,7 +2041,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Creality/CR-20/Configuration_adv.h b/config/examples/Creality/CR-20/Configuration_adv.h index 523f37c91d..1c6e4767de 100644 --- a/config/examples/Creality/CR-20/Configuration_adv.h +++ b/config/examples/Creality/CR-20/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + #define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Creality/CR-8/Configuration.h b/config/examples/Creality/CR-8/Configuration.h index a8771aa13a..2163890342 100644 --- a/config/examples/Creality/CR-8/Configuration.h +++ b/config/examples/Creality/CR-8/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2047,7 +2048,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Creality/CR-8/Configuration_adv.h b/config/examples/Creality/CR-8/Configuration_adv.h index 4c3d7c44c0..ff7d7560c1 100644 --- a/config/examples/Creality/CR-8/Configuration_adv.h +++ b/config/examples/Creality/CR-8/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Creality/Ender-2/Configuration.h b/config/examples/Creality/Ender-2/Configuration.h index 7cc74ed631..cc6031700c 100644 --- a/config/examples/Creality/Ender-2/Configuration.h +++ b/config/examples/Creality/Ender-2/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2041,7 +2042,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Creality/Ender-2/Configuration_adv.h b/config/examples/Creality/Ender-2/Configuration_adv.h index 2d896555ea..ad3772283f 100644 --- a/config/examples/Creality/Ender-2/Configuration_adv.h +++ b/config/examples/Creality/Ender-2/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Creality/Ender-3/Configuration.h b/config/examples/Creality/Ender-3/Configuration.h index 30845b1109..6be4c819e2 100644 --- a/config/examples/Creality/Ender-3/Configuration.h +++ b/config/examples/Creality/Ender-3/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2041,7 +2042,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Creality/Ender-3/Configuration_adv.h b/config/examples/Creality/Ender-3/Configuration_adv.h index 4d0fde40ec..934e90c8f0 100644 --- a/config/examples/Creality/Ender-3/Configuration_adv.h +++ b/config/examples/Creality/Ender-3/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + #define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Creality/Ender-4/Configuration.h b/config/examples/Creality/Ender-4/Configuration.h index 6b8d9dfd0f..854bafa620 100644 --- a/config/examples/Creality/Ender-4/Configuration.h +++ b/config/examples/Creality/Ender-4/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2047,7 +2048,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Creality/Ender-4/Configuration_adv.h b/config/examples/Creality/Ender-4/Configuration_adv.h index 924d179d6e..69a2cc8c23 100644 --- a/config/examples/Creality/Ender-4/Configuration_adv.h +++ b/config/examples/Creality/Ender-4/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Creality/Ender-5/Configuration.h b/config/examples/Creality/Ender-5/Configuration.h index 2d69021115..60fc34fc56 100644 --- a/config/examples/Creality/Ender-5/Configuration.h +++ b/config/examples/Creality/Ender-5/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2040,7 +2041,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Creality/Ender-5/Configuration_adv.h b/config/examples/Creality/Ender-5/Configuration_adv.h index 8c8d90cf95..b41330d8c5 100644 --- a/config/examples/Creality/Ender-5/Configuration_adv.h +++ b/config/examples/Creality/Ender-5/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + #define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Dagoma/Disco Ultimate/Configuration.h b/config/examples/Dagoma/Disco Ultimate/Configuration.h index 183a86b969..3c84a4b43c 100644 --- a/config/examples/Dagoma/Disco Ultimate/Configuration.h +++ b/config/examples/Dagoma/Disco Ultimate/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 18 #define TEMP_SENSOR_1 0 @@ -2037,7 +2038,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h index a62a8ab9bf..df03640280 100644 --- a/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h +++ b/config/examples/Dagoma/Disco Ultimate/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + #define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration.h b/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration.h index e665c3f924..80df69ca49 100644 --- a/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration.h +++ b/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2042,7 +2043,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h b/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h index e47abe3877..fca511a9e5 100644 --- a/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h +++ b/config/examples/EVNOVO (Artillery)/Sidewinder X1/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Einstart-S/Configuration.h b/config/examples/Einstart-S/Configuration.h index 9566ea6e08..310d278a85 100644 --- a/config/examples/Einstart-S/Configuration.h +++ b/config/examples/Einstart-S/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 666 #define TEMP_SENSOR_1 0 @@ -2047,7 +2048,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Einstart-S/Configuration_adv.h b/config/examples/Einstart-S/Configuration_adv.h index 460cba4cb4..91da99eb2e 100644 --- a/config/examples/Einstart-S/Configuration_adv.h +++ b/config/examples/Einstart-S/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration.h b/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration.h index 6a673d1678..4b868cfddf 100644 --- a/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration.h +++ b/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration.h @@ -360,6 +360,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -403,7 +404,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2043,7 +2044,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h b/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h index 9b1c2b2bb4..8248ff470e 100644 --- a/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h +++ b/config/examples/FYSETC/Cheetah 1.2/BLTouch/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - #define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/FYSETC/Cheetah 1.2/base/Configuration.h b/config/examples/FYSETC/Cheetah 1.2/base/Configuration.h index 30262687d1..83031dacf9 100644 --- a/config/examples/FYSETC/Cheetah 1.2/base/Configuration.h +++ b/config/examples/FYSETC/Cheetah 1.2/base/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2042,7 +2043,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h b/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h index aeb8fdb041..a9a24bb9f1 100644 --- a/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h +++ b/config/examples/FYSETC/Cheetah 1.2/base/Configuration_adv.h @@ -657,10 +657,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -850,11 +850,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -879,23 +900,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - #define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -930,6 +934,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Felix/Configuration.h b/config/examples/Felix/Configuration.h index 96f8ffae3d..7587468801 100644 --- a/config/examples/Felix/Configuration.h +++ b/config/examples/Felix/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2019,7 +2020,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Felix/Configuration_adv.h b/config/examples/Felix/Configuration_adv.h index 42eb54a5eb..fff253fd85 100644 --- a/config/examples/Felix/Configuration_adv.h +++ b/config/examples/Felix/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Felix/DUAL/Configuration.h b/config/examples/Felix/DUAL/Configuration.h index 78d5b4e745..75a8565edb 100644 --- a/config/examples/Felix/DUAL/Configuration.h +++ b/config/examples/Felix/DUAL/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 1 @@ -2019,7 +2020,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/FlashForge/CreatorPro/Configuration.h b/config/examples/FlashForge/CreatorPro/Configuration.h index 80d9f15670..2eab8f96a9 100644 --- a/config/examples/FlashForge/CreatorPro/Configuration.h +++ b/config/examples/FlashForge/CreatorPro/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 -2 #define TEMP_SENSOR_1 -2 @@ -2028,7 +2029,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/FlashForge/CreatorPro/Configuration_adv.h b/config/examples/FlashForge/CreatorPro/Configuration_adv.h index cb7fbb2591..2132aa0a10 100644 --- a/config/examples/FlashForge/CreatorPro/Configuration_adv.h +++ b/config/examples/FlashForge/CreatorPro/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -850,11 +850,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + #define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 255 // User defined GREEN value + #define LED_USER_PRESET_BLUE 255 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + #define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -879,23 +900,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 255 // User defined GREEN value - #define LED_USER_PRESET_BLUE 255 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - #define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -930,6 +934,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/FolgerTech/i3-2020/Configuration.h b/config/examples/FolgerTech/i3-2020/Configuration.h index 167e79b64a..75c5a2e9ab 100644 --- a/config/examples/FolgerTech/i3-2020/Configuration.h +++ b/config/examples/FolgerTech/i3-2020/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -2043,7 +2044,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/FolgerTech/i3-2020/Configuration_adv.h b/config/examples/FolgerTech/i3-2020/Configuration_adv.h index 08872f1c59..e3019a470d 100644 --- a/config/examples/FolgerTech/i3-2020/Configuration_adv.h +++ b/config/examples/FolgerTech/i3-2020/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Formbot/Raptor/Configuration.h b/config/examples/Formbot/Raptor/Configuration.h index af39334300..a2634819a7 100644 --- a/config/examples/Formbot/Raptor/Configuration.h +++ b/config/examples/Formbot/Raptor/Configuration.h @@ -400,6 +400,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -443,7 +444,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2142,7 +2143,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Formbot/Raptor/Configuration_adv.h b/config/examples/Formbot/Raptor/Configuration_adv.h index 14969a1989..1ec9c56aa7 100644 --- a/config/examples/Formbot/Raptor/Configuration_adv.h +++ b/config/examples/Formbot/Raptor/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + #define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Formbot/T_Rex_2+/Configuration.h b/config/examples/Formbot/T_Rex_2+/Configuration.h index 0d1882fe5e..a4b5334550 100644 --- a/config/examples/Formbot/T_Rex_2+/Configuration.h +++ b/config/examples/Formbot/T_Rex_2+/Configuration.h @@ -368,6 +368,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -411,7 +412,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 1 @@ -2071,7 +2072,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h index 22b28967ae..4c65cca41c 100644 --- a/config/examples/Formbot/T_Rex_2+/Configuration_adv.h +++ b/config/examples/Formbot/T_Rex_2+/Configuration_adv.h @@ -662,10 +662,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -855,11 +855,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + #define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -884,23 +905,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -935,6 +939,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Formbot/T_Rex_3/Configuration.h b/config/examples/Formbot/T_Rex_3/Configuration.h index b2339cf5b9..49d1a5387a 100644 --- a/config/examples/Formbot/T_Rex_3/Configuration.h +++ b/config/examples/Formbot/T_Rex_3/Configuration.h @@ -363,6 +363,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -406,7 +407,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 1 @@ -2065,7 +2066,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Formbot/T_Rex_3/Configuration_adv.h b/config/examples/Formbot/T_Rex_3/Configuration_adv.h index 91b9f2572a..daf25ef62c 100644 --- a/config/examples/Formbot/T_Rex_3/Configuration_adv.h +++ b/config/examples/Formbot/T_Rex_3/Configuration_adv.h @@ -662,10 +662,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -855,11 +855,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + #define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -884,23 +905,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -935,6 +939,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Fysetc/AIO_II/Configuration.h b/config/examples/Fysetc/AIO_II/Configuration.h index 564fa808ef..dd26faa4c0 100644 --- a/config/examples/Fysetc/AIO_II/Configuration.h +++ b/config/examples/Fysetc/AIO_II/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2042,7 +2043,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Fysetc/AIO_II/Configuration_adv.h b/config/examples/Fysetc/AIO_II/Configuration_adv.h index 8c5a747fc1..d2456953db 100644 --- a/config/examples/Fysetc/AIO_II/Configuration_adv.h +++ b/config/examples/Fysetc/AIO_II/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + #define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + #define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - #define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Fysetc/CHEETAH/BLTouch/Configuration.h b/config/examples/Fysetc/CHEETAH/BLTouch/Configuration.h index 175ae500a9..cd14d80eca 100644 --- a/config/examples/Fysetc/CHEETAH/BLTouch/Configuration.h +++ b/config/examples/Fysetc/CHEETAH/BLTouch/Configuration.h @@ -355,6 +355,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -2025,7 +2026,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Fysetc/CHEETAH/BLTouch/Configuration_adv.h b/config/examples/Fysetc/CHEETAH/BLTouch/Configuration_adv.h index 3495ab379f..8ddaa533c8 100644 --- a/config/examples/Fysetc/CHEETAH/BLTouch/Configuration_adv.h +++ b/config/examples/Fysetc/CHEETAH/BLTouch/Configuration_adv.h @@ -657,10 +657,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -850,11 +850,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -879,23 +900,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - #define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -930,6 +934,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Fysetc/CHEETAH/base/Configuration.h b/config/examples/Fysetc/CHEETAH/base/Configuration.h index d8a6ef9b93..99523eb517 100644 --- a/config/examples/Fysetc/CHEETAH/base/Configuration.h +++ b/config/examples/Fysetc/CHEETAH/base/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2042,7 +2043,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Fysetc/CHEETAH/base/Configuration_adv.h b/config/examples/Fysetc/CHEETAH/base/Configuration_adv.h index 3495ab379f..8ddaa533c8 100644 --- a/config/examples/Fysetc/CHEETAH/base/Configuration_adv.h +++ b/config/examples/Fysetc/CHEETAH/base/Configuration_adv.h @@ -657,10 +657,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -850,11 +850,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -879,23 +900,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - #define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -930,6 +934,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Fysetc/F6_13/Configuration.h b/config/examples/Fysetc/F6_13/Configuration.h index b91f18f2db..5d5c922439 100644 --- a/config/examples/Fysetc/F6_13/Configuration.h +++ b/config/examples/Fysetc/F6_13/Configuration.h @@ -361,6 +361,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -404,7 +405,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2039,7 +2040,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Fysetc/F6_13/Configuration_adv.h b/config/examples/Fysetc/F6_13/Configuration_adv.h index 92df163f3d..b2ced98e33 100644 --- a/config/examples/Fysetc/F6_13/Configuration_adv.h +++ b/config/examples/Fysetc/F6_13/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Geeetech/A10/Configuration.h b/config/examples/Geeetech/A10/Configuration.h index 5c7b525961..aa121eb0d9 100644 --- a/config/examples/Geeetech/A10/Configuration.h +++ b/config/examples/Geeetech/A10/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2022,7 +2023,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Geeetech/A10/Configuration_adv.h b/config/examples/Geeetech/A10/Configuration_adv.h index e1a2c689bc..3e92df1be5 100644 --- a/config/examples/Geeetech/A10/Configuration_adv.h +++ b/config/examples/Geeetech/A10/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + #define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Geeetech/A10M/Configuration.h b/config/examples/Geeetech/A10M/Configuration.h index 740b105b1f..f5ad6e8c72 100644 --- a/config/examples/Geeetech/A10M/Configuration.h +++ b/config/examples/Geeetech/A10M/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2022,7 +2023,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Geeetech/A10M/Configuration_adv.h b/config/examples/Geeetech/A10M/Configuration_adv.h index 60ee17e885..01555c75e0 100644 --- a/config/examples/Geeetech/A10M/Configuration_adv.h +++ b/config/examples/Geeetech/A10M/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + #define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define POWER_LOSS_PIN 69 // Pin to detect power loss #define POWER_LOSS_STATE LOW // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Geeetech/A20M/Configuration.h b/config/examples/Geeetech/A20M/Configuration.h index 3c6a193ec1..5e9d6b1743 100644 --- a/config/examples/Geeetech/A20M/Configuration.h +++ b/config/examples/Geeetech/A20M/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2024,7 +2025,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Geeetech/A20M/Configuration_adv.h b/config/examples/Geeetech/A20M/Configuration_adv.h index f8c9535314..508957550a 100644 --- a/config/examples/Geeetech/A20M/Configuration_adv.h +++ b/config/examples/Geeetech/A20M/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + #define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define POWER_LOSS_PIN 69 // Pin to detect power loss #define POWER_LOSS_STATE LOW // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Geeetech/GT2560/Configuration.h b/config/examples/Geeetech/GT2560/Configuration.h index 7ff2517878..de79058f30 100644 --- a/config/examples/Geeetech/GT2560/Configuration.h +++ b/config/examples/Geeetech/GT2560/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2052,7 +2053,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h index aec16d1536..172d5f58f4 100644 --- a/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h +++ b/config/examples/Geeetech/I3_Pro_X-GT2560/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2037,7 +2038,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Geeetech/MeCreator2/Configuration.h b/config/examples/Geeetech/MeCreator2/Configuration.h index 7d7d77d0a6..bde857d36c 100644 --- a/config/examples/Geeetech/MeCreator2/Configuration.h +++ b/config/examples/Geeetech/MeCreator2/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2044,7 +2045,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Geeetech/MeCreator2/Configuration_adv.h b/config/examples/Geeetech/MeCreator2/Configuration_adv.h index 4857dc5bba..aa3fa1510f 100644 --- a/config/examples/Geeetech/MeCreator2/Configuration_adv.h +++ b/config/examples/Geeetech/MeCreator2/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h index 666c5c9c55..1c9847f8a4 100644 --- a/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2058,7 +2059,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h index c5c9718671..db70d1cb0b 100644 --- a/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2057,7 +2058,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h index 0d078bf6af..aa4908d799 100644 --- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 1 @@ -2037,7 +2038,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h index e1a2c689bc..3e92df1be5 100644 --- a/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h +++ b/config/examples/Geeetech/Prusa i3 Pro C/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + #define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h index 1d7f93d835..ae0e7cda66 100644 --- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h +++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2037,7 +2038,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h index e1a2c689bc..3e92df1be5 100644 --- a/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h +++ b/config/examples/Geeetech/Prusa i3 Pro W/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + #define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/HMS434/Configuration.h b/config/examples/HMS434/Configuration.h new file mode 100644 index 0000000000..c4a91c1236 --- /dev/null +++ b/config/examples/HMS434/Configuration.h @@ -0,0 +1,2199 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Configuration.h + * + * Basic settings such as: + * + * - Type of electronics + * - Type of temperature sensor + * - Printer geometry + * - Endstop configuration + * - LCD controller + * - Extra features + * + * Advanced settings can be found in Configuration_adv.h + * + */ +#define CONFIGURATION_H_VERSION 020000 + +//=========================================================================== +//============================= Getting Started ============================= +//=========================================================================== + +/** + * Here are some standard links for getting your machine calibrated: + * + * http://reprap.org/wiki/Calibration + * http://youtu.be/wAL9d7FgInk + * http://calculator.josefprusa.cz + * http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide + * http://www.thingiverse.com/thing:5573 + * https://sites.google.com/site/repraplogphase/calibration-of-your-reprap + * http://www.thingiverse.com/thing:298812 + */ + +//=========================================================================== +//============================= DELTA Printer =============================== +//=========================================================================== +// For a Delta printer start with one of the configuration files in the +// config/examples/delta directory and customize for your machine. +// + +//=========================================================================== +//============================= SCARA Printer =============================== +//=========================================================================== +// For a SCARA printer start with the configuration files in +// config/examples/SCARA and customize for your machine. +// + +// @section info + +// User-specified version info of this build to display in [Pronterface, etc] terminal window during +// startup. Implementation of an idea by Prof Braino to inform user that any changes made to this +// build by the user have been successfully uploaded into firmware. +#define STRING_CONFIG_H_AUTHOR "(Scheepers, MaukCC)" // Who made the changes. +#define SHOW_BOOTSCREEN +#define STRING_SPLASH_LINE1 SHORT_BUILD_VERSION // will be shown during bootup in line 1 +#define STRING_SPLASH_LINE2 WEBSITE_URL // will be shown during bootup in line 2 + +/** + * *** VENDORS PLEASE READ *** + * + * Marlin allows you to add a custom boot image for Graphical LCDs. + * With this option Marlin will first show your custom screen followed + * by the standard Marlin logo with version number and web URL. + * + * We encourage you to take advantage of this new feature and we also + * respectfully request that you retain the unmodified Marlin boot screen. + */ + +// Enable to show the bitmap in Marlin/_Bootscreen.h on startup. +//#define SHOW_CUSTOM_BOOTSCREEN + +// Enable to show the bitmap in Marlin/_Statusscreen.h on the status screen. +//#define CUSTOM_STATUS_SCREEN_IMAGE + +// @section machine + +/** + * Select the serial port on the board to use for communication with the host. + * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Note: The first serial port (-1 or 0) will always be used by the Arduino bootloader. + * + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] + */ +#define SERIAL_PORT 0 + +/** + * Select a secondary serial port on the board to use for communication with the host. + * This allows the connection of wireless adapters (for instance) to non-default port pins. + * Serial port -1 is the USB emulated serial port, if available. + * + * :[-1, 0, 1, 2, 3, 4, 5, 6, 7] + */ +//#define SERIAL_PORT_2 -1 + +/** + * This setting determines the communication speed of the printer. + * + * 250000 works in most cases, but you might try a lower speed if + * you commonly experience drop-outs during host printing. + * You may try up to 1000000 to speed up SD file transfer. + * + * :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000] + */ +#define BAUDRATE 250000 + +// Enable the Bluetooth serial interface on AT90USB devices +//#define BLUETOOTH + +// Choose the name from boards.h that matches your setup +#ifndef MOTHERBOARD + #define MOTHERBOARD BOARD_CNCONTROLS_15 +#endif + +// Name displayed in the LCD "Ready" message and Info menu +//#define CUSTOM_MACHINE_NAME "3D Printer" + +// Printer's unique ID, used by some programs to differentiate between machines. +// Choose your own or use a service like http://www.uuidgenerator.net/version4 +#define MACHINE_UUID "75083866-86ea-42b2-b475-7b3a7855e716" + +// @section extruder + +// This defines the number of extruders +// :[1, 2, 3, 4, 5, 6] +#define EXTRUDERS 1 + +// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc. +#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75 + +// For Cyclops or any "multi-extruder" that shares a single nozzle. +//#define SINGLENOZZLE + +/** + * Průša MK2 Single Nozzle Multi-Material Multiplexer, and variants. + * + * This device allows one stepper driver on a control board to drive + * two to eight stepper motors, one at a time, in a manner suitable + * for extruders. + * + * This option only allows the multiplexer to switch on tool-change. + * Additional options to configure custom E moves are pending. + */ +//#define MK2_MULTIPLEXER +#if ENABLED(MK2_MULTIPLEXER) + // Override the default DIO selector pins here, if needed. + // Some pins files may provide defaults for these pins. + //#define E_MUX0_PIN 40 // Always Required + //#define E_MUX1_PIN 42 // Needed for 3 to 8 inputs + //#define E_MUX2_PIN 44 // Needed for 5 to 8 inputs +#endif + +/** + * Prusa Multi-Material Unit v2 + * + * Requires NOZZLE_PARK_FEATURE to park print head in case MMU unit fails. + * Requires EXTRUDERS = 5 + * + * For additional configuration see Configuration_adv.h + */ +//#define PRUSA_MMU2 + +// A dual extruder that uses a single stepper motor +//#define SWITCHING_EXTRUDER +#if ENABLED(SWITCHING_EXTRUDER) + #define SWITCHING_EXTRUDER_SERVO_NR 0 + #define SWITCHING_EXTRUDER_SERVO_ANGLES { 0, 90 } // Angles for E0, E1[, E2, E3] + #if EXTRUDERS > 3 + #define SWITCHING_EXTRUDER_E23_SERVO_NR 1 + #endif +#endif + +// A dual-nozzle that uses a servomotor to raise/lower one (or both) of the nozzles +//#define SWITCHING_NOZZLE +#if ENABLED(SWITCHING_NOZZLE) + #define SWITCHING_NOZZLE_SERVO_NR 0 + //#define SWITCHING_NOZZLE_E1_SERVO_NR 1 // If two servos are used, the index of the second + #define SWITCHING_NOZZLE_SERVO_ANGLES { 0, 90 } // Angles for E0, E1 (single servo) or lowered/raised (dual servo) +#endif + +/** + * Two separate X-carriages with extruders that connect to a moving part + * via a solenoid docking mechanism. Requires SOL1_PIN and SOL2_PIN. + */ +//#define PARKING_EXTRUDER + +/** + * Two separate X-carriages with extruders that connect to a moving part + * via a magnetic docking mechanism using movements and no solenoid + * + * project : https://www.thingiverse.com/thing:3080893 + * movements : https://youtu.be/0xCEiG9VS3k + * https://youtu.be/Bqbcs0CU2FE + */ +//#define MAGNETIC_PARKING_EXTRUDER + +#if EITHER(PARKING_EXTRUDER, MAGNETIC_PARKING_EXTRUDER) + + #define PARKING_EXTRUDER_PARKING_X { -78, 184 } // X positions for parking the extruders + #define PARKING_EXTRUDER_GRAB_DISTANCE 1 // (mm) Distance to move beyond the parking point to grab the extruder + //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381 + + #if ENABLED(PARKING_EXTRUDER) + + #define PARKING_EXTRUDER_SOLENOIDS_INVERT // If enabled, the solenoid is NOT magnetized with applied voltage + #define PARKING_EXTRUDER_SOLENOIDS_PINS_ACTIVE LOW // LOW or HIGH pin signal energizes the coil + #define PARKING_EXTRUDER_SOLENOIDS_DELAY 250 // (ms) Delay for magnetic field. No delay if 0 or not defined. + //#define MANUAL_SOLENOID_CONTROL // Manual control of docking solenoids with M380 S / M381 + + #elif ENABLED(MAGNETIC_PARKING_EXTRUDER) + + #define MPE_FAST_SPEED 9000 // (mm/m) Speed for travel before last distance point + #define MPE_SLOW_SPEED 4500 // (mm/m) Speed for last distance travel to park and couple + #define MPE_TRAVEL_DISTANCE 10 // (mm) Last distance point + #define MPE_COMPENSATION 0 // Offset Compensation -1 , 0 , 1 (multiplier) only for coupling + + #endif + +#endif + +/** + * Switching Toolhead + * + * Support for swappable and dockable toolheads, such as + * the E3D Tool Changer. Toolheads are locked with a servo. + */ +//#define SWITCHING_TOOLHEAD + +/** + * Magnetic Switching Toolhead + * + * Support swappable and dockable toolheads with a magnetic + * docking mechanism using movement and no servo. + */ +//#define MAGNETIC_SWITCHING_TOOLHEAD + +/** + * Electromagnetic Switching Toolhead + * + * Parking for CoreXY / HBot kinematics. + * Toolheads are parked at one edge and held with an electromagnet. + * Supports more than 2 Toolheads. See https://youtu.be/JolbsAKTKf4 + */ +//#define ELECTROMAGNETIC_SWITCHING_TOOLHEAD + +#if ANY(SWITCHING_TOOLHEAD, MAGNETIC_SWITCHING_TOOLHEAD, ELECTROMAGNETIC_SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_Y_POS 235 // (mm) Y position of the toolhead dock + #define SWITCHING_TOOLHEAD_Y_SECURITY 10 // (mm) Security distance Y axis + #define SWITCHING_TOOLHEAD_Y_CLEAR 60 // (mm) Minimum distance from dock for unobstructed X axis + #define SWITCHING_TOOLHEAD_X_POS { 215, 0 } // (mm) X positions for parking the extruders + #if ENABLED(SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_SERVO_NR 2 // Index of the servo connector + #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 } // (degrees) Angles for Lock, Unlock + #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_Y_RELEASE 5 // (mm) Security distance Y axis + #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) + //#define PRIME_BEFORE_REMOVE // Prime the nozzle before release from the dock + #if ENABLED(PRIME_BEFORE_REMOVE) + #define SWITCHING_TOOLHEAD_PRIME_MM 20 // (mm) Extruder prime length + #define SWITCHING_TOOLHEAD_RETRACT_MM 10 // (mm) Retract after priming length + #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE 300 // (mm/m) Extruder prime feedrate + #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400 // (mm/m) Extruder retract feedrate + #endif + #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) + #define SWITCHING_TOOLHEAD_Z_HOP 2 // (mm) Z raise for switching + #endif +#endif + +/** + * "Mixing Extruder" + * - Adds G-codes M163 and M164 to set and "commit" the current mix factors. + * - Extends the stepping routines to move multiple steppers in proportion to the mix. + * - Optional support for Repetier Firmware's 'M164 S' supporting virtual tools. + * - This implementation supports up to two mixing extruders. + * - Enable DIRECT_MIXING_IN_G1 for M165 and mixing in G1 (from Pia Taubert's reference implementation). + */ +//#define MIXING_EXTRUDER +#if ENABLED(MIXING_EXTRUDER) + #define MIXING_STEPPERS 2 // Number of steppers in your mixing extruder + #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164 + //#define DIRECT_MIXING_IN_G1 // Allow ABCDHI mix factors in G1 movement commands + //#define GRADIENT_MIX // Support for gradient mixing with M166 and LCD + #if ENABLED(GRADIENT_MIX) + //#define GRADIENT_VTOOL // Add M166 T to use a V-tool index as a Gradient alias + #endif +#endif + +// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing). +// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder). +// For the other hotends it is their distance from the extruder 0 hotend. +//#define HOTEND_OFFSET_X { 0.0, 20.00 } // (mm) relative X-offset for each nozzle +//#define HOTEND_OFFSET_Y { 0.0, 5.00 } // (mm) relative Y-offset for each nozzle +//#define HOTEND_OFFSET_Z { 0.0, 0.00 } // (mm) relative Z-offset for each nozzle + +// @section machine + +/** + * Power Supply Control + * + * Enable and connect the power supply to the PS_ON_PIN. + * Specify whether the power supply is active HIGH or active LOW. + */ +//#define PSU_CONTROL +//#define PSU_NAME "Power Supply" + +#if ENABLED(PSU_CONTROL) + #define PSU_ACTIVE_HIGH false // Set 'false' for ATX (1), 'true' for X-Box (2) + + //#define PS_DEFAULT_OFF // Keep power off until enabled directly with M80 + + //#define AUTO_POWER_CONTROL // Enable automatic control of the PS_ON pin + #if ENABLED(AUTO_POWER_CONTROL) + #define AUTO_POWER_FANS // Turn on PSU if fans need power + #define AUTO_POWER_E_FANS + #define AUTO_POWER_CONTROLLERFAN + #define AUTO_POWER_CHAMBER_FAN + //#define AUTO_POWER_E_TEMP 50 // (°C) Turn on PSU over this temperature + //#define AUTO_POWER_CHAMBER_TEMP 30 // (°C) Turn on PSU over this temperature + #define POWER_TIMEOUT 30 + #endif +#endif + +// @section temperature + +//=========================================================================== +//============================= Thermal Settings ============================ +//=========================================================================== + +/** + * --NORMAL IS 4.7kohm PULLUP!-- 1kohm pullup can be used on hotend sensor, using correct resistor and table + * + * Temperature sensors available: + * + * -4 : thermocouple with AD8495 + * -3 : thermocouple with MAX31855 (only for sensor 0) + * -2 : thermocouple with MAX6675 (only for sensor 0) + * -1 : thermocouple with AD595 + * 0 : not used + * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) + * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) + * 3 : Mendel-parts thermistor (4.7k pullup) + * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! + * 5 : 100K thermistor - ATC Semitec 104GT-2/104NT-4-R025H42G (Used in ParCan & J-Head) (4.7k pullup) + * 501 : 100K Zonestar (Tronxy X3A) Thermistor + * 512 : 100k RPW-Ultra hotend thermistor (4.7k pullup) + * 6 : 100k EPCOS - Not as accurate as table 1 (created using a fluke thermocouple) (4.7k pullup) + * 7 : 100k Honeywell thermistor 135-104LAG-J01 (4.7k pullup) + * 71 : 100k Honeywell thermistor 135-104LAF-J01 (4.7k pullup) + * 8 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) + * 9 : 100k GE Sensing AL03006-58.2K-97-G1 (4.7k pullup) + * 10 : 100k RS thermistor 198-961 (4.7k pullup) + * 11 : 100k beta 3950 1% thermistor (4.7k pullup) + * 12 : 100k 0603 SMD Vishay NTCS0603E3104FXT (4.7k pullup) (calibrated for Makibox hot bed) + * 13 : 100k Hisens 3950 1% up to 300°C for hotend "Simple ONE " & "Hotend "All In ONE" + * 15 : 100k thermistor calibration for JGAurora A5 hotend + * 18 : ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327 + * 20 : Pt100 with circuit in the Ultimainboard V2.x + * 201 : Pt100 with circuit in Overlord, similar to Ultimainboard V2.x + * 60 : 100k Maker's Tool Works Kapton Bed Thermistor beta=3950 + * 61 : 100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup + * 66 : 4.7M High Temperature thermistor from Dyze Design + * 67 : 450C thermistor from SliceEngineering + * 70 : the 100K thermistor found in the bq Hephestos 2 + * 75 : 100k Generic Silicon Heat Pad with NTC 100K MGB18-104F39050L32 thermistor + * + * 1k ohm pullup tables - This is atypical, and requires changing out the 4.7k pullup for 1k. + * (but gives greater accuracy and more stable PID) + * 51 : 100k thermistor - EPCOS (1k pullup) + * 52 : 200k thermistor - ATC Semitec 204GT-2 (1k pullup) + * 55 : 100k thermistor - ATC Semitec 104GT-2 (Used in ParCan & J-Head) (1k pullup) + * + * 1047 : Pt1000 with 4k7 pullup + * 1010 : Pt1000 with 1k pullup (non standard) + * 147 : Pt100 with 4k7 pullup + * 110 : Pt100 with 1k pullup (non standard) + * + * 1000 : Custom - Specify parameters in Configuration_adv.h + * + * Use these for Testing or Development purposes. NEVER for production machine. + * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. + * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. + * + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + */ +#define TEMP_SENSOR_0 -1 +#define TEMP_SENSOR_1 0 +#define TEMP_SENSOR_2 0 +#define TEMP_SENSOR_3 0 +#define TEMP_SENSOR_4 0 +#define TEMP_SENSOR_5 0 +#define TEMP_SENSOR_BED 331 +#define TEMP_SENSOR_CHAMBER 331 + +// Dummy thermistor constant temperature readings, for use with 998 and 999 +#define DUMMY_THERMISTOR_998_VALUE 25 +#define DUMMY_THERMISTOR_999_VALUE 100 + +// Use temp sensor 1 as a redundant sensor with sensor 0. If the readings +// from the two sensors differ too much the print will be aborted. +//#define TEMP_SENSOR_1_AS_REDUNDANT +#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10 + +#define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109 +#define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer +#define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target + +#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190 +#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer +#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target + +// Below this temperature the heater will be switched off +// because it probably indicates a broken thermistor wire. +#define HEATER_0_MINTEMP 5 +#define HEATER_1_MINTEMP 5 +#define HEATER_2_MINTEMP 5 +#define HEATER_3_MINTEMP 5 +#define HEATER_4_MINTEMP 5 +#define HEATER_5_MINTEMP 5 +#define BED_MINTEMP 5 + +// Above this temperature the heater will be switched off. +// This can protect components from overheating, but NOT from shorts and failures. +// (Use MINTEMP for thermistor short/failure protection.) +#define HEATER_0_MAXTEMP 410 +#define HEATER_1_MAXTEMP 410 +#define HEATER_2_MAXTEMP 410 +#define HEATER_3_MAXTEMP 410 +#define BED_MAXTEMP 150 + +//=========================================================================== +//============================= PID Settings ================================ +//=========================================================================== +// PID Tuning Guide here: http://reprap.org/wiki/PID_Tuning + +// Comment the following line to disable PID and enable bang-bang. +#define PIDTEMP +#define BANG_MAX 255 // Limits current to nozzle while in bang-bang mode; 255=full current +#define PID_MAX 170 // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current +#define PID_K1 0.95 // Smoothing factor within any PID loop +#if ENABLED(PIDTEMP) + //#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM) + //#define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM) + //#define PID_DEBUG // Sends debug data to the serial port. + //#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX + //#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay + //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders) + // Set/get with gcode: M301 E[extruder number, 0-2] + #define PID_FUNCTIONAL_RANGE 20 // If the temperature difference between the target temperature and the actual temperature + // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max. + + // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it + + #define DEFAULT_Kp 11.3 + #define DEFAULT_Ki 0.61 + #define DEFAULT_Kd 52.77 + +#endif // PIDTEMP + +//=========================================================================== +//====================== PID > Bed Temperature Control ====================== +//=========================================================================== + +/** + * PID Bed Heating + * + * If this option is enabled set PID constants below. + * If this option is disabled, bang-bang will be used and BED_LIMIT_SWITCHING will enable hysteresis. + * + * The PID frequency will be the same as the extruder PWM. + * If PID_dT is the default, and correct for the hardware/configuration, that means 7.689Hz, + * which is fine for driving a square wave into a resistive load and does not significantly + * impact FET heating. This also works fine on a Fotek SSR-10DA Solid State Relay into a 250W + * heater. If your configuration is significantly different than this and you don't understand + * the issues involved, don't use bed PID until someone else verifies that your hardware works. + */ +//#define PIDTEMPBED + +//#define BED_LIMIT_SWITCHING + +/** + * Max Bed Power + * Applies to all forms of bed control (PID, bang-bang, and bang-bang with hysteresis). + * When set to any value below 255, enables a form of PWM to the bed that acts like a divider + * so don't use it unless you are OK with PWM on your bed. (See the comment on enabling PIDTEMPBED) + */ +#define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current + +#if ENABLED(PIDTEMPBED) + //#define MIN_BED_POWER 0 + //#define PID_BED_DEBUG // Sends debug data to the serial port. + + //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) + //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10) + #define DEFAULT_bedKp 10.00 + #define DEFAULT_bedKi .023 + #define DEFAULT_bedKd 305.4 + + //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+) + //from pidautotune + //#define DEFAULT_bedKp 97.1 + //#define DEFAULT_bedKi 1.41 + //#define DEFAULT_bedKd 1675.16 + + // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles. +#endif // PIDTEMPBED + +// @section extruder + +/** + * Prevent extrusion if the temperature is below EXTRUDE_MINTEMP. + * Add M302 to set the minimum extrusion temperature and/or turn + * cold extrusion prevention on and off. + * + * *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! *** + */ +#define PREVENT_COLD_EXTRUSION +#define EXTRUDE_MINTEMP 18 + +/** + * Prevent a single extrusion longer than EXTRUDE_MAXLENGTH. + * Note: For Bowden Extruders make this large enough to allow load/unload. + */ +#define PREVENT_LENGTHY_EXTRUDE +#define EXTRUDE_MAXLENGTH 200 + +//=========================================================================== +//======================== Thermal Runaway Protection ======================= +//=========================================================================== + +/** + * Thermal Protection provides additional protection to your printer from damage + * and fire. Marlin always includes safe min and max temperature ranges which + * protect against a broken or disconnected thermistor wire. + * + * The issue: If a thermistor falls out, it will report the much lower + * temperature of the air in the room, and the the firmware will keep + * the heater on. + * + * If you get "Thermal Runaway" or "Heating failed" errors the + * details can be tuned in Configuration_adv.h + */ + +#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders +#define THERMAL_PROTECTION_BED // Enable thermal protection for the heated bed +#define THERMAL_PROTECTION_CHAMBER // Enable thermal protection for the heated chamber + +//=========================================================================== +//============================= Mechanical Settings ========================= +//=========================================================================== + +// @section machine + +// Uncomment one of these options to enable CoreXY, CoreXZ, or CoreYZ kinematics +// either in the usual order or reversed +//#define COREXY +//#define COREXZ +//#define COREYZ +//#define COREYX +//#define COREZX +//#define COREZY + +//=========================================================================== +//============================== Endstop Settings =========================== +//=========================================================================== + +// @section homing + +// Specify here all the endstop connectors that are connected to any endstop or probe. +// Almost all printers will be using one per axis. Probes will use one or more of the +// extra connectors. Leave undefined any used for non-endstop and non-probe purposes. +#define USE_XMIN_PLUG +#define USE_YMIN_PLUG +#define USE_ZMIN_PLUG +//#define USE_XMAX_PLUG +//#define USE_YMAX_PLUG +//#define USE_ZMAX_PLUG + +// Enable pullup for all endstops to prevent a floating state +#define ENDSTOPPULLUPS +#if DISABLED(ENDSTOPPULLUPS) + // Disable ENDSTOPPULLUPS to set pullups individually + //#define ENDSTOPPULLUP_XMAX + //#define ENDSTOPPULLUP_YMAX + //#define ENDSTOPPULLUP_ZMAX + //#define ENDSTOPPULLUP_XMIN + //#define ENDSTOPPULLUP_YMIN + //#define ENDSTOPPULLUP_ZMIN + //#define ENDSTOPPULLUP_ZMIN_PROBE +#endif + +// Enable pulldown for all endstops to prevent a floating state +//#define ENDSTOPPULLDOWNS +#if DISABLED(ENDSTOPPULLDOWNS) + // Disable ENDSTOPPULLDOWNS to set pulldowns individually + //#define ENDSTOPPULLDOWN_XMAX + //#define ENDSTOPPULLDOWN_YMAX + //#define ENDSTOPPULLDOWN_ZMAX + //#define ENDSTOPPULLDOWN_XMIN + //#define ENDSTOPPULLDOWN_YMIN + //#define ENDSTOPPULLDOWN_ZMIN + //#define ENDSTOPPULLDOWN_ZMIN_PROBE +#endif + +// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup). +#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop. +#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop. +#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop. +#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop. +#define Z_MIN_PROBE_ENDSTOP_INVERTING true // Set to true to invert the logic of the probe. + +/** + * Stepper Drivers + * + * These settings allow Marlin to tune stepper driver timing and enable advanced options for + * stepper drivers that support them. You may also override timing options in Configuration_adv.h. + * + * A4988 is assumed for unspecified drivers. + * + * Options: A4988, A5984, DRV8825, LV8729, L6470, TB6560, TB6600, TMC2100, + * TMC2130, TMC2130_STANDALONE, TMC2160, TMC2160_STANDALONE, + * TMC2208, TMC2208_STANDALONE, TMC2209, TMC2209_STANDALONE, + * TMC26X, TMC26X_STANDALONE, TMC2660, TMC2660_STANDALONE, + * TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE + * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE'] + */ +//#define X_DRIVER_TYPE A4988 +//#define Y_DRIVER_TYPE A4988 +//#define Z_DRIVER_TYPE A4988 +//#define X2_DRIVER_TYPE A4988 +//#define Y2_DRIVER_TYPE A4988 +//#define Z2_DRIVER_TYPE A4988 +//#define Z3_DRIVER_TYPE A4988 +//#define E0_DRIVER_TYPE A4988 +//#define E1_DRIVER_TYPE A4988 +//#define E2_DRIVER_TYPE A4988 +//#define E3_DRIVER_TYPE A4988 +//#define E4_DRIVER_TYPE A4988 +//#define E5_DRIVER_TYPE A4988 + +// Enable this feature if all enabled endstop pins are interrupt-capable. +// This will remove the need to poll the interrupt pins, saving many CPU cycles. +//#define ENDSTOP_INTERRUPTS_FEATURE + +/** + * Endstop Noise Threshold + * + * Enable if your probe or endstops falsely trigger due to noise. + * + * - Higher values may affect repeatability or accuracy of some bed probes. + * - To fix noise install a 100nF ceramic capacitor inline with the switch. + * - This feature is not required for common micro-switches mounted on PCBs + * based on the Makerbot design, which already have the 100nF capacitor. + * + * :[2,3,4,5,6,7] + */ +//#define ENDSTOP_NOISE_THRESHOLD 2 + +//============================================================================= +//============================== Movement Settings ============================ +//============================================================================= +// @section motion + +/** + * Default Settings + * + * These settings can be reset by M502 + * + * Note that if EEPROM is enabled, saved values will override these. + */ + +/** + * With this option each E stepper can have its own factors for the + * following movement settings. If fewer factors are given than the + * total number of extruders, the last value applies to the rest. + */ +//#define DISTINCT_E_FACTORS + +/** + * Default Axis Steps Per Unit (steps/mm) + * Override with M92 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] + */ +#define DEFAULT_AXIS_STEPS_PER_UNIT { 53.45, 71.19, 160, 169.05 } + +/** + * Default Max Feed Rate (mm/s) + * Override with M203 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] + */ +#define DEFAULT_MAX_FEEDRATE { 1000, 1000, 40, 25 } + +/** + * Default Max Acceleration (change/s) change = mm/s + * (Maximum start speed for accelerated moves) + * Override with M201 + * X, Y, Z, E0 [, E1[, E2[, E3[, E4[, E5]]]]] + */ +#define DEFAULT_MAX_ACCELERATION { 500, 500, 100, 10000 } + +/** + * Default Acceleration (change/s) change = mm/s + * Override with M204 + * + * M204 P Acceleration + * M204 R Retract Acceleration + * M204 T Travel Acceleration + */ +#define DEFAULT_ACCELERATION 500 // X, Y, Z and E acceleration for printing moves +#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts +#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves + +/** + * Junction Deviation + * + * Use Junction Deviation instead of traditional Jerk Limiting + * + * See: + * https://reprap.org/forum/read.php?1,739819 + * http://blog.kyneticcnc.com/2018/10/computing-junction-deviation-for-marlin.html + */ +//#define JUNCTION_DEVIATION +#if ENABLED(JUNCTION_DEVIATION) + #define JUNCTION_DEVIATION_MM 0.02 // (mm) Distance from real junction edge +#endif + +/** + * Default Jerk (mm/s) + * Override with M205 X Y Z E + * + * "Jerk" specifies the minimum speed change that requires acceleration. + * When changing speed and direction, if the difference is less than the + * value set here, it may happen instantaneously. + */ +#if DISABLED(JUNCTION_DEVIATION) + #define DEFAULT_XJERK 10.0 + #define DEFAULT_YJERK 10.0 + #define DEFAULT_ZJERK 0.3 +#endif + +#define DEFAULT_EJERK 5.0 // May be used by Linear Advance + +/** + * S-Curve Acceleration + * + * This option eliminates vibration during printing by fitting a Bézier + * curve to move acceleration, producing much smoother direction changes. + * + * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained + */ +//#define S_CURVE_ACCELERATION + +//=========================================================================== +//============================= Z Probe Options ============================= +//=========================================================================== +// @section probes + +// +// See http://marlinfw.org/docs/configuration/probes.html +// + +/** + * Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + * + * Enable this option for a probe connected to the Z Min endstop pin. + */ +//#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN + +/** + * Z_MIN_PROBE_PIN + * + * Define this pin if the probe is not connected to Z_MIN_PIN. + * If not defined the default pin for the selected MOTHERBOARD + * will be used. Most of the time the default is what you want. + * + * - The simplest option is to use a free endstop connector. + * - Use 5V for powered (usually inductive) sensors. + * + * - RAMPS 1.3/1.4 boards may use the 5V, GND, and Aux4->D32 pin: + * - For simple switches connect... + * - normally-closed switches to GND and D32. + * - normally-open switches to 5V and D32. + * + */ +//#define Z_MIN_PROBE_PIN 32 // Pin 32 is the RAMPS default + +/** + * Probe Type + * + * Allen Key Probes, Servo Probes, Z-Sled Probes, FIX_MOUNTED_PROBE, etc. + * Activate one of these to use Auto Bed Leveling below. + */ + +/** + * The "Manual Probe" provides a means to do "Auto" Bed Leveling without a probe. + * Use G29 repeatedly, adjusting the Z height at each point with movement commands + * or (with LCD_BED_LEVELING) the LCD controller. + */ +//#define PROBE_MANUALLY +//#define MANUAL_PROBE_START_Z 0.2 + +/** + * A Fix-Mounted Probe either doesn't deploy or needs manual deployment. + * (e.g., an inductive probe or a nozzle-based probe-switch.) + */ +#define FIX_MOUNTED_PROBE + +/** + * Z Servo Probe, such as an endstop switch on a rotating arm. + */ +//#define Z_PROBE_SERVO_NR 0 // Defaults to SERVO 0 connector. +//#define Z_SERVO_ANGLES { 70, 0 } // Z Servo Deploy and Stow angles + +/** + * The BLTouch probe uses a Hall effect sensor and emulates a servo. + */ +//#define BLTOUCH + +/** + * Touch-MI Probe by hotends.fr + * + * This probe is deployed and activated by moving the X-axis to a magnet at the edge of the bed. + * By default, the magnet is assumed to be on the left and activated by a home. If the magnet is + * on the right, enable and set TOUCH_MI_DEPLOY_XPOS to the deploy position. + * + * Also requires: BABYSTEPPING, BABYSTEP_ZPROBE_OFFSET, Z_SAFE_HOMING, + * and a minimum Z_HOMING_HEIGHT of 10. + */ +//#define TOUCH_MI_PROBE +#if ENABLED(TOUCH_MI_PROBE) + #define TOUCH_MI_RETRACT_Z 0.5 // Height at which the probe retracts + //#define TOUCH_MI_DEPLOY_XPOS (X_MAX_BED + 2) // For a magnet on the right side of the bed + //#define TOUCH_MI_MANUAL_DEPLOY // For manual deploy (LCD menu) +#endif + +// A probe that is deployed and stowed with a solenoid pin (SOL1_PIN) +//#define SOLENOID_PROBE + +// A sled-mounted probe like those designed by Charles Bell. +//#define Z_PROBE_SLED +//#define SLED_DOCKING_OFFSET 5 // The extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like. + +// A probe deployed by moving the x-axis, such as the Wilson II's rack-and-pinion probe designed by Marty Rice. +//#define RACK_AND_PINION_PROBE +#if ENABLED(RACK_AND_PINION_PROBE) + #define Z_PROBE_DEPLOY_X X_MIN_POS + #define Z_PROBE_RETRACT_X X_MAX_POS +#endif + +// +// For Z_PROBE_ALLEN_KEY see the Delta example configurations. +// + +/** + * Z Probe to nozzle (X,Y) offset, relative to (0, 0). + * X and Y offsets must be integers. + * + * In the following example the X and Y offsets are both positive: + * #define X_PROBE_OFFSET_FROM_EXTRUDER 10 + * #define Y_PROBE_OFFSET_FROM_EXTRUDER 10 + * + * +-- BACK ---+ + * | | + * L | (+) P | R <-- probe (20,20) + * E | | I + * F | (-) N (+) | G <-- nozzle (10,10) + * T | | H + * | (-) | T + * | | + * O-- FRONT --+ + * (0,0) + */ +#define X_PROBE_OFFSET_FROM_EXTRUDER -21 // X offset: -left +right [of the nozzle] +#define Y_PROBE_OFFSET_FROM_EXTRUDER 22 // Y offset: -front +behind [the nozzle] +#define Z_PROBE_OFFSET_FROM_EXTRUDER -1.54 // Z offset: -below +above [the nozzle] + +// Certain types of probes need to stay away from edges +#define MIN_PROBE_EDGE 20 + +// X and Y axis travel speed (mm/m) between probes +#define XY_PROBE_SPEED 12000 + +// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2) +#define Z_PROBE_SPEED_FAST 900 + +// Feedrate (mm/m) for the "accurate" probe of each point +#define Z_PROBE_SPEED_SLOW 100 + +/** + * Multiple Probing + * + * You may get improved results by probing 2 or more times. + * With EXTRA_PROBING the more atypical reading(s) will be disregarded. + * + * A total of 2 does fast/slow probes with a weighted average. + * A total of 3 or more adds more slow probes, taking the average. + */ +#define MULTIPLE_PROBING 2 +//#define EXTRA_PROBING 1 + +/** + * Z probes require clearance when deploying, stowing, and moving between + * probe points to avoid hitting the bed and other hardware. + * Servo-mounted probes require extra space for the arm to rotate. + * Inductive probes need space to keep from triggering early. + * + * Use these settings to specify the distance (mm) to raise the probe (or + * lower the bed). The values set here apply over and above any (negative) + * probe Z Offset set with Z_PROBE_OFFSET_FROM_EXTRUDER, M851, or the LCD. + * Only integer values >= 1 are valid here. + * + * Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle. + * But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle. + */ +#define Z_CLEARANCE_DEPLOY_PROBE 5 // Z Clearance for Deploy/Stow +#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points +#define Z_CLEARANCE_MULTI_PROBE 1 // Z Clearance between multiple probes +#define Z_AFTER_PROBING 5 // Z position after probing is done + +#define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping + +// For M851 give a range for adjusting the Z probe offset +#define Z_PROBE_OFFSET_RANGE_MIN -20 +#define Z_PROBE_OFFSET_RANGE_MAX 20 + +// Enable the M48 repeatability test to test probe accuracy +//#define Z_MIN_PROBE_REPEATABILITY_TEST + +// Before deploy/stow pause for user confirmation +//#define PAUSE_BEFORE_DEPLOY_STOW +#if ENABLED(PAUSE_BEFORE_DEPLOY_STOW) + //#define PAUSE_PROBE_DEPLOY_WHEN_TRIGGERED // For Manual Deploy Allenkey Probe +#endif + +/** + * Enable one or more of the following if probing seems unreliable. + * Heaters and/or fans can be disabled during probing to minimize electrical + * noise. A delay can also be added to allow noise and vibration to settle. + * These options are most useful for the BLTouch probe, but may also improve + * readings with inductive probes and piezo sensors. + */ +//#define PROBING_HEATERS_OFF // Turn heaters off when probing +#if ENABLED(PROBING_HEATERS_OFF) + //#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy) +#endif +//#define PROBING_FANS_OFF // Turn fans off when probing +//#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing +//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors + +// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1 +// :{ 0:'Low', 1:'High' } +#define X_ENABLE_ON 0 +#define Y_ENABLE_ON 0 +#define Z_ENABLE_ON 0 +#define E_ENABLE_ON 0 // For all extruders + +// Disables axis stepper immediately when it's not being used. +// WARNING: When motors turn off there is a chance of losing position accuracy! +#define DISABLE_X false +#define DISABLE_Y false +#define DISABLE_Z false + +// Warn on display about possibly reduced accuracy +//#define DISABLE_REDUCED_ACCURACY_WARNING + +// @section extruder + +#define DISABLE_E false // For all extruders +#define DISABLE_INACTIVE_EXTRUDER // Keep only the active extruder enabled + +// @section machine + +// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way. +#define INVERT_X_DIR true +#define INVERT_Y_DIR false +#define INVERT_Z_DIR true + +// @section extruder + +// For direct drive extruder v9 set to true, for geared extruder set to false. +#define INVERT_E0_DIR false +#define INVERT_E1_DIR false +#define INVERT_E2_DIR false +#define INVERT_E3_DIR false +#define INVERT_E4_DIR false +#define INVERT_E5_DIR false + +// @section homing + +//#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed + +//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off. + +#define Z_HOMING_HEIGHT 4 // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ... + // Be sure you have this distance over your Z_MAX_POS in case. + +// Direction of endstops when homing; 1=MAX, -1=MIN +// :[-1,1] +#define X_HOME_DIR -1 +#define Y_HOME_DIR -1 +#define Z_HOME_DIR -1 + +// @section machine + +// The size of the print bed +#define X_BED_SIZE 450 +#define Y_BED_SIZE 325 + +// Travel limits (mm) after homing, corresponding to endstop positions. +#define X_MIN_POS -72 +#define Y_MIN_POS -84 +#define Z_MIN_POS 0 +#define X_MAX_POS X_BED_SIZE +#define Y_MAX_POS Y_BED_SIZE +#define Z_MAX_POS 400 + +/** + * Software Endstops + * + * - Prevent moves outside the set machine bounds. + * - Individual axes can be disabled, if desired. + * - X and Y only apply to Cartesian robots. + * - Use 'M211' to set software endstops on/off or report current state + */ + +// Min software endstops constrain movement within minimum coordinate bounds +#define MIN_SOFTWARE_ENDSTOPS +#if ENABLED(MIN_SOFTWARE_ENDSTOPS) + #define MIN_SOFTWARE_ENDSTOP_X + #define MIN_SOFTWARE_ENDSTOP_Y + #define MIN_SOFTWARE_ENDSTOP_Z +#endif + +// Max software endstops constrain movement within maximum coordinate bounds +#define MAX_SOFTWARE_ENDSTOPS +#if ENABLED(MAX_SOFTWARE_ENDSTOPS) + #define MAX_SOFTWARE_ENDSTOP_X + #define MAX_SOFTWARE_ENDSTOP_Y + #define MAX_SOFTWARE_ENDSTOP_Z +#endif + +#if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS) + //#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD +#endif + +/** + * Filament Runout Sensors + * Mechanical or opto endstops are used to check for the presence of filament. + * + * RAMPS-based boards use SERVO3_PIN for the first runout sensor. + * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc. + * By default the firmware assumes HIGH=FILAMENT PRESENT. + */ +#define FILAMENT_RUNOUT_SENSOR +#if ENABLED(FILAMENT_RUNOUT_SENSOR) + #define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each. + #define FIL_RUNOUT_INVERTING false // Set to true to invert the logic of the sensor. + #define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins. + //#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins. + + // Set one or more commands to execute on filament runout. + // (After 'M412 H' Marlin will ask the host to handle the process.) + #define FILAMENT_RUNOUT_SCRIPT "M600" + + // After a runout is detected, continue printing this length of filament + // before executing the runout script. Useful for a sensor at the end of + // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead. + //#define FILAMENT_RUNOUT_DISTANCE_MM 25 + + #ifdef FILAMENT_RUNOUT_DISTANCE_MM + // Enable this option to use an encoder disc that toggles the runout pin + // as the filament moves. (Be sure to set FILAMENT_RUNOUT_DISTANCE_MM + // large enough to avoid false positives.) + //#define FILAMENT_MOTION_SENSOR + #endif +#endif + +//=========================================================================== +//=============================== Bed Leveling ============================== +//=========================================================================== +// @section calibrate + +/** + * Choose one of the options below to enable G29 Bed Leveling. The parameters + * and behavior of G29 will change depending on your selection. + * + * If using a Probe for Z Homing, enable Z_SAFE_HOMING also! + * + * - AUTO_BED_LEVELING_3POINT + * Probe 3 arbitrary points on the bed (that aren't collinear) + * You specify the XY coordinates of all 3 points. + * The result is a single tilted plane. Best for a flat bed. + * + * - AUTO_BED_LEVELING_LINEAR + * Probe several points in a grid. + * You specify the rectangle and the density of sample points. + * The result is a single tilted plane. Best for a flat bed. + * + * - AUTO_BED_LEVELING_BILINEAR + * Probe several points in a grid. + * You specify the rectangle and the density of sample points. + * The result is a mesh, best for large or uneven beds. + * + * - AUTO_BED_LEVELING_UBL (Unified Bed Leveling) + * A comprehensive bed leveling system combining the features and benefits + * of other systems. UBL also includes integrated Mesh Generation, Mesh + * Validation and Mesh Editing systems. + * + * - MESH_BED_LEVELING + * Probe a grid manually + * The result is a mesh, suitable for large or uneven beds. (See BILINEAR.) + * For machines without a probe, Mesh Bed Leveling provides a method to perform + * leveling in steps so you can manually adjust the Z height at each grid-point. + * With an LCD controller the process is guided step-by-step. + */ +//#define AUTO_BED_LEVELING_3POINT +#define AUTO_BED_LEVELING_LINEAR +//#define AUTO_BED_LEVELING_BILINEAR +//#define AUTO_BED_LEVELING_UBL +//#define MESH_BED_LEVELING + +/** + * Normally G28 leaves leveling disabled on completion. Enable + * this option to have G28 restore the prior leveling state. + */ +//#define RESTORE_LEVELING_AFTER_G28 + +/** + * Enable detailed logging of G28, G29, M48, etc. + * Turn on with the command 'M111 S32'. + * NOTE: Requires a lot of PROGMEM! + */ +//#define DEBUG_LEVELING_FEATURE + +#if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_BILINEAR, AUTO_BED_LEVELING_UBL) + // Gradually reduce leveling correction until a set height is reached, + // at which point movement will be level to the machine's XY plane. + // The height can be set with M420 Z + #define ENABLE_LEVELING_FADE_HEIGHT + + // For Cartesian machines, instead of dividing moves on mesh boundaries, + // split up moves into short segments like a Delta. This follows the + // contours of the bed more closely than edge-to-edge straight moves. + #define SEGMENT_LEVELED_MOVES + #define LEVELED_SEGMENT_LENGTH 5.0 // (mm) Length of all segments (except the last one) + + /** + * Enable the G26 Mesh Validation Pattern tool. + */ + //#define G26_MESH_VALIDATION + #if ENABLED(G26_MESH_VALIDATION) + #define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle. + #define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool. + #define MESH_TEST_HOTEND_TEMP 205 // (°C) Default nozzle temperature for the G26 Mesh Validation Tool. + #define MESH_TEST_BED_TEMP 60 // (°C) Default bed temperature for the G26 Mesh Validation Tool. + #define G26_XY_FEEDRATE 20 // (mm/s) Feedrate for XY Moves for the G26 Mesh Validation Tool. + #endif + +#endif + +#if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR) + + // Set the number of grid points per dimension. + #define GRID_MAX_POINTS_X 5 + #define GRID_MAX_POINTS_Y 3 + + // Set the boundaries for probing (where the probe can reach). + //#define LEFT_PROBE_BED_POSITION MIN_PROBE_EDGE + //#define RIGHT_PROBE_BED_POSITION (X_BED_SIZE - (MIN_PROBE_EDGE)) + //#define FRONT_PROBE_BED_POSITION MIN_PROBE_EDGE + //#define BACK_PROBE_BED_POSITION (Y_BED_SIZE - (MIN_PROBE_EDGE)) + + // Probe along the Y axis, advancing X after each column + //#define PROBE_Y_FIRST + + #if ENABLED(AUTO_BED_LEVELING_BILINEAR) + + // Beyond the probed grid, continue the implied tilt? + // Default is to maintain the height of the nearest edge. + //#define EXTRAPOLATE_BEYOND_GRID + + // + // Experimental Subdivision of the grid by Catmull-Rom method. + // Synthesizes intermediate points to produce a more detailed mesh. + // + //#define ABL_BILINEAR_SUBDIVISION + #if ENABLED(ABL_BILINEAR_SUBDIVISION) + // Number of subdivisions between probe points + #define BILINEAR_SUBDIVISIONS 3 + #endif + + #endif + +#elif ENABLED(AUTO_BED_LEVELING_UBL) + + //=========================================================================== + //========================= Unified Bed Leveling ============================ + //=========================================================================== + + //#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh + + #define MESH_INSET 1 // Set Mesh bounds as an inset region of the bed + #define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited. + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + #define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle + #define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500 + + //#define UBL_Z_RAISE_WHEN_OFF_MESH 2.5 // When the nozzle is off the mesh, this value is used + // as the Z-Height correction value. + +#elif ENABLED(MESH_BED_LEVELING) + + //=========================================================================== + //=================================== Mesh ================================== + //=========================================================================== + + #define MESH_INSET 10 // Set Mesh bounds as an inset region of the bed + #define GRID_MAX_POINTS_X 3 // Don't use more than 7 points per axis, implementation limited. + #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X + + //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS + +#endif // BED_LEVELING + +/** + * Points to probe for all 3-point Leveling procedures. + * Override if the automatically selected points are inadequate. + */ +#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL) + //#define PROBE_PT_1_X 15 + //#define PROBE_PT_1_Y 180 + //#define PROBE_PT_2_X 15 + //#define PROBE_PT_2_Y 20 + //#define PROBE_PT_3_X 170 + //#define PROBE_PT_3_Y 20 +#endif + +/** + * Add a bed leveling sub-menu for ABL or MBL. + * Include a guided procedure if manual probing is enabled. + */ +//#define LCD_BED_LEVELING + +#if ENABLED(LCD_BED_LEVELING) + #define MESH_EDIT_Z_STEP 0.025 // (mm) Step size while manually probing Z axis. + #define LCD_PROBE_Z_RANGE 4 // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment + //#define MESH_EDIT_MENU // Add a menu to edit mesh points +#endif + +// Add a menu item to move between bed corners for manual bed adjustment +//#define LEVEL_BED_CORNERS + +#if ENABLED(LEVEL_BED_CORNERS) + #define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling + #define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Move nozzle up before moving between corners + #define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points + //#define LEVEL_CENTER_TOO // Move to the center after the last corner +#endif + +/** + * Commands to execute at the end of G29 probing. + * Useful to retract or move the Z probe out of the way. + */ +//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10" + + +// @section homing + +// The center of the bed is at (X=0, Y=0) +//#define BED_CENTER_AT_0_0 + +// Manually set the home position. Leave these undefined for automatic settings. +// For DELTA this is the top-center of the Cartesian print volume. +//#define MANUAL_X_HOME_POS 0 +//#define MANUAL_Y_HOME_POS 0 +//#define MANUAL_Z_HOME_POS 0 + +// Use "Z Safe Homing" to avoid homing with a Z probe outside the bed area. +// +// With this feature enabled: +// +// - Allow Z homing only after X and Y homing AND stepper drivers still enabled. +// - If stepper drivers time out, it will need X and Y homing again before Z homing. +// - Move the Z probe (or nozzle) to a defined XY point before Z Homing when homing all axes (G28). +// - Prevent Z homing when the Z probe is outside bed area. +// +//#define Z_SAFE_HOMING + +#if ENABLED(Z_SAFE_HOMING) + #define Z_SAFE_HOMING_X_POINT ((X_BED_SIZE) / 2) // X point for Z homing when homing all axes (G28). + #define Z_SAFE_HOMING_Y_POINT ((Y_BED_SIZE) / 2) // Y point for Z homing when homing all axes (G28). +#endif + +// Homing speeds (mm/m) +#define HOMING_FEEDRATE_XY (6000) +#define HOMING_FEEDRATE_Z (900) + +// Validate that endstops are triggered on homing moves +#define VALIDATE_HOMING_ENDSTOPS + +// @section calibrate + +/** + * Bed Skew Compensation + * + * This feature corrects for misalignment in the XYZ axes. + * + * Take the following steps to get the bed skew in the XY plane: + * 1. Print a test square (e.g., https://www.thingiverse.com/thing:2563185) + * 2. For XY_DIAG_AC measure the diagonal A to C + * 3. For XY_DIAG_BD measure the diagonal B to D + * 4. For XY_SIDE_AD measure the edge A to D + * + * Marlin automatically computes skew factors from these measurements. + * Skew factors may also be computed and set manually: + * + * - Compute AB : SQRT(2*AC*AC+2*BD*BD-4*AD*AD)/2 + * - XY_SKEW_FACTOR : TAN(PI/2-ACOS((AC*AC-AB*AB-AD*AD)/(2*AB*AD))) + * + * If desired, follow the same procedure for XZ and YZ. + * Use these diagrams for reference: + * + * Y Z Z + * ^ B-------C ^ B-------C ^ B-------C + * | / / | / / | / / + * | / / | / / | / / + * | A-------D | A-------D | A-------D + * +-------------->X +-------------->X +-------------->Y + * XY_SKEW_FACTOR XZ_SKEW_FACTOR YZ_SKEW_FACTOR + */ +//#define SKEW_CORRECTION + +#if ENABLED(SKEW_CORRECTION) + // Input all length measurements here: + #define XY_DIAG_AC 282.8427124746 + #define XY_DIAG_BD 282.8427124746 + #define XY_SIDE_AD 200 + + // Or, set the default skew factors directly here + // to override the above measurements: + #define XY_SKEW_FACTOR 0.0 + + //#define SKEW_CORRECTION_FOR_Z + #if ENABLED(SKEW_CORRECTION_FOR_Z) + #define XZ_DIAG_AC 282.8427124746 + #define XZ_DIAG_BD 282.8427124746 + #define YZ_DIAG_AC 282.8427124746 + #define YZ_DIAG_BD 282.8427124746 + #define YZ_SIDE_AD 200 + #define XZ_SKEW_FACTOR 0.0 + #define YZ_SKEW_FACTOR 0.0 + #endif + + // Enable this option for M852 to set skew at runtime + //#define SKEW_CORRECTION_GCODE +#endif + +//============================================================================= +//============================= Additional Features =========================== +//============================================================================= + +// @section extras + +/** + * EEPROM + * + * Persistent storage to preserve configurable settings across reboots. + * + * M500 - Store settings to EEPROM. + * M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes) + * M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.) + */ +#define EEPROM_SETTINGS // Persistent storage with M500 and M501 +//#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release! +#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM. +#if ENABLED(EEPROM_SETTINGS) + //#define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors. +#endif + +// +// Host Keepalive +// +// When enabled Marlin will send a busy status message to the host +// every couple of seconds when it can't accept commands. +// +#define HOST_KEEPALIVE_FEATURE // Disable this if your host doesn't like keepalive messages +#define DEFAULT_KEEPALIVE_INTERVAL 2 // Number of seconds between "busy" messages. Set with M113. +#define BUSY_WHILE_HEATING // Some hosts require "busy" messages even during heating + +// +// M100 Free Memory Watcher +// +//#define M100_FREE_MEMORY_WATCHER // Add M100 (Free Memory Watcher) to debug memory usage + +// +// G20/G21 Inch mode support +// +//#define INCH_MODE_SUPPORT + +// +// M149 Set temperature units support +// +//#define TEMPERATURE_UNITS_SUPPORT + +// @section temperature + +// Preheat Constants +#define PREHEAT_1_LABEL "PLA" +#define PREHEAT_1_TEMP_HOTEND 180 +#define PREHEAT_1_TEMP_BED 70 +#define PREHEAT_1_FAN_SPEED 0 // Value from 0 to 255 + +#define PREHEAT_2_LABEL "ABS" +#define PREHEAT_2_TEMP_HOTEND 240 +#define PREHEAT_2_TEMP_BED 110 +#define PREHEAT_2_FAN_SPEED 0 // Value from 0 to 255 + +/** + * Nozzle Park + * + * Park the nozzle at the given XYZ position on idle or G27. + * + * The "P" parameter controls the action applied to the Z axis: + * + * P0 (Default) If Z is below park Z raise the nozzle. + * P1 Raise the nozzle always to Z-park height. + * P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS. + */ +#define NOZZLE_PARK_FEATURE + +#if ENABLED(NOZZLE_PARK_FEATURE) + // Specify a park position as { X, Y, Z_raise } + #define NOZZLE_PARK_POINT { 225, -50, 5 } + #define NOZZLE_PARK_XY_FEEDRATE 150 // (mm/s) X and Y axes feedrate (also used for delta Z axis) + #define NOZZLE_PARK_Z_FEEDRATE 15 // (mm/s) Z axis feedrate (not used for delta printers) +#endif + +/** + * Clean Nozzle Feature -- EXPERIMENTAL + * + * Adds the G12 command to perform a nozzle cleaning process. + * + * Parameters: + * P Pattern + * S Strokes / Repetitions + * T Triangles (P1 only) + * + * Patterns: + * P0 Straight line (default). This process requires a sponge type material + * at a fixed bed location. "S" specifies strokes (i.e. back-forth motions) + * between the start / end points. + * + * P1 Zig-zag pattern between (X0, Y0) and (X1, Y1), "T" specifies the + * number of zig-zag triangles to do. "S" defines the number of strokes. + * Zig-zags are done in whichever is the narrower dimension. + * For example, "G12 P1 S1 T3" will execute: + * + * -- + * | (X0, Y1) | /\ /\ /\ | (X1, Y1) + * | | / \ / \ / \ | + * A | | / \ / \ / \ | + * | | / \ / \ / \ | + * | (X0, Y0) | / \/ \/ \ | (X1, Y0) + * -- +--------------------------------+ + * |________|_________|_________| + * T1 T2 T3 + * + * P2 Circular pattern with middle at NOZZLE_CLEAN_CIRCLE_MIDDLE. + * "R" specifies the radius. "S" specifies the stroke count. + * Before starting, the nozzle moves to NOZZLE_CLEAN_START_POINT. + * + * Caveats: The ending Z should be the same as starting Z. + * Attention: EXPERIMENTAL. G-code arguments may change. + * + */ +#define NOZZLE_CLEAN_FEATURE + +#if ENABLED(NOZZLE_CLEAN_FEATURE) + // Default number of pattern repetitions + #define NOZZLE_CLEAN_STROKES 4 + + // Default number of triangles + #define NOZZLE_CLEAN_TRIANGLES 2 + + // Specify positions as { X, Y, Z } . Leave Z blank to not change the Z position + #define NOZZLE_CLEAN_START_POINT { -37, -67, } + #define NOZZLE_CLEAN_END_POINT { 100, 60, (Z_MIN_POS + 1) } + + // Circular pattern radius + #define NOZZLE_CLEAN_CIRCLE_RADIUS 8 + // Circular pattern circle fragments number + #define NOZZLE_CLEAN_CIRCLE_FN 10 + // Middle point of circle + #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT + + // Move the nozzle to the initial position after cleaning + #define NOZZLE_CLEAN_GOBACK + + // Enable for a purge/clean station that's always at the gantry height (thus no Z move) + #define NOZZLE_CLEAN_NO_Z +#endif + +/** + * Print Job Timer + * + * Automatically start and stop the print job timer on M104/M109/M190. + * + * M104 (hotend, no wait) - high temp = none, low temp = stop timer + * M109 (hotend, wait) - high temp = start timer, low temp = stop timer + * M190 (bed, wait) - high temp = start timer, low temp = none + * + * The timer can also be controlled with the following commands: + * + * M75 - Start the print job timer + * M76 - Pause the print job timer + * M77 - Stop the print job timer + */ +#define PRINTJOB_TIMER_AUTOSTART + +/** + * Print Counter + * + * Track statistical data such as: + * + * - Total print jobs + * - Total successful print jobs + * - Total failed print jobs + * - Total time printing + * + * View the current statistics with M78. + */ +#define PRINTCOUNTER + +//============================================================================= +//============================= LCD and SD support ============================ +//============================================================================= + +// @section lcd + +/** + * LCD LANGUAGE + * + * Select the language to display on the LCD. These languages are available: + * + * en, an, bg, ca, cz, da, de, el, el-gr, es, eu, fi, fr, gl, hr, it, + * jp-kana, ko_KR, nl, pl, pt, pt-br, ru, sk, tr, uk, zh_CN, zh_TW, test + * + * :{ 'en':'English', 'an':'Aragonese', 'bg':'Bulgarian', 'ca':'Catalan', 'cz':'Czech', 'da':'Danish', 'de':'German', 'el':'Greek', 'el-gr':'Greek (Greece)', 'es':'Spanish', 'eu':'Basque-Euskera', 'fi':'Finnish', 'fr':'French', 'gl':'Galician', 'hr':'Croatian', 'it':'Italian', 'jp-kana':'Japanese', 'ko_KR':'Korean (South Korea)', 'nl':'Dutch', 'pl':'Polish', 'pt':'Portuguese', 'pt-br':'Portuguese (Brazilian)', 'ru':'Russian', 'sk':'Slovak', 'tr':'Turkish', 'uk':'Ukrainian', 'zh_CN':'Chinese (Simplified)', 'zh_TW':'Chinese (Traditional)', 'test':'TEST' } + */ +#define LCD_LANGUAGE en + +/** + * LCD Character Set + * + * Note: This option is NOT applicable to Graphical Displays. + * + * All character-based LCDs provide ASCII plus one of these + * language extensions: + * + * - JAPANESE ... the most common + * - WESTERN ... with more accented characters + * - CYRILLIC ... for the Russian language + * + * To determine the language extension installed on your controller: + * + * - Compile and upload with LCD_LANGUAGE set to 'test' + * - Click the controller to view the LCD menu + * - The LCD will display Japanese, Western, or Cyrillic text + * + * See http://marlinfw.org/docs/development/lcd_language.html + * + * :['JAPANESE', 'WESTERN', 'CYRILLIC'] + */ +#define DISPLAY_CHARSET_HD44780 JAPANESE + +/** + * Info Screen Style (0:Classic, 1:Prusa) + * + * :[0:'Classic', 1:'Prusa'] + */ +#define LCD_INFO_SCREEN_STYLE 0 + +/** + * SD CARD + * + * SD Card support is disabled by default. If your controller has an SD slot, + * you must uncomment the following option or it won't work. + * + */ +#define SDSUPPORT + +/** + * SD CARD: SPI SPEED + * + * Enable one of the following items for a slower SPI transfer speed. + * This may be required to resolve "volume init" errors. + */ +//#define SPI_SPEED SPI_HALF_SPEED +//#define SPI_SPEED SPI_QUARTER_SPEED +//#define SPI_SPEED SPI_EIGHTH_SPEED + +/** + * SD CARD: ENABLE CRC + * + * Use CRC checks and retries on the SD communication. + */ +//#define SD_CHECK_AND_RETRY + +/** + * LCD Menu Items + * + * Disable all menus and only display the Status Screen, or + * just remove some extraneous menu items to recover space. + */ +//#define NO_LCD_MENUS +//#define SLIM_LCD_MENUS + +// +// ENCODER SETTINGS +// +// This option overrides the default number of encoder pulses needed to +// produce one step. Should be increased for high-resolution encoders. +// +//#define ENCODER_PULSES_PER_STEP 4 + +// +// Use this option to override the number of step signals required to +// move between next/prev menu items. +// +//#define ENCODER_STEPS_PER_MENU_ITEM 1 + +/** + * Encoder Direction Options + * + * Test your encoder's behavior first with both options disabled. + * + * Reversed Value Edit and Menu Nav? Enable REVERSE_ENCODER_DIRECTION. + * Reversed Menu Navigation only? Enable REVERSE_MENU_DIRECTION. + * Reversed Value Editing only? Enable BOTH options. + */ + +// +// This option reverses the encoder direction everywhere. +// +// Set this option if CLOCKWISE causes values to DECREASE +// +//#define REVERSE_ENCODER_DIRECTION + +// +// This option reverses the encoder direction for navigating LCD menus. +// +// If CLOCKWISE normally moves DOWN this makes it go UP. +// If CLOCKWISE normally moves UP this makes it go DOWN. +// +//#define REVERSE_MENU_DIRECTION + +// +// This option reverses the encoder direction for Select Screen. +// +// If CLOCKWISE normally moves LEFT this makes it go RIGHT. +// If CLOCKWISE normally moves RIGHT this makes it go LEFT. +// +//#define REVERSE_SELECT_DIRECTION + +// +// Individual Axis Homing +// +// Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu. +// +//#define INDIVIDUAL_AXIS_HOMING_MENU + +// +// SPEAKER/BUZZER +// +// If you have a speaker that can produce tones, enable it here. +// By default Marlin assumes you have a buzzer with a fixed frequency. +// +#define SPEAKER + +// +// The duration and frequency for the UI feedback sound. +// Set these to 0 to disable audio feedback in the LCD menus. +// +// Note: Test audio output with the G-Code: +// M300 S P +// +//#define LCD_FEEDBACK_FREQUENCY_DURATION_MS 2 +//#define LCD_FEEDBACK_FREQUENCY_HZ 5000 + +//============================================================================= +//======================== LCD / Controller Selection ========================= +//======================== (Character-based LCDs) ========================= +//============================================================================= + +// +// RepRapDiscount Smart Controller. +// http://reprap.org/wiki/RepRapDiscount_Smart_Controller +// +// Note: Usually sold with a white PCB. +// +//#define REPRAP_DISCOUNT_SMART_CONTROLLER + +// +// Original RADDS LCD Display+Encoder+SDCardReader +// http://doku.radds.org/dokumentation/lcd-display/ +// +//#define RADDS_DISPLAY + +// +// ULTIMAKER Controller. +// +//#define ULTIMAKERCONTROLLER + +// +// ULTIPANEL as seen on Thingiverse. +// +//#define ULTIPANEL + +// +// PanelOne from T3P3 (via RAMPS 1.4 AUX2/AUX3) +// http://reprap.org/wiki/PanelOne +// +//#define PANEL_ONE + +// +// GADGETS3D G3D LCD/SD Controller +// http://reprap.org/wiki/RAMPS_1.3/1.4_GADGETS3D_Shield_with_Panel +// +// Note: Usually sold with a blue PCB. +// +//#define G3D_PANEL + +// +// RigidBot Panel V1.0 +// http://www.inventapart.com/ +// +//#define RIGIDBOT_PANEL + +// +// Makeboard 3D Printer Parts 3D Printer Mini Display 1602 Mini Controller +// https://www.aliexpress.com/item/Micromake-Makeboard-3D-Printer-Parts-3D-Printer-Mini-Display-1602-Mini-Controller-Compatible-with-Ramps-1/32765887917.html +// +//#define MAKEBOARD_MINI_2_LINE_DISPLAY_1602 + +// +// ANET and Tronxy 20x4 Controller +// +//#define ZONESTAR_LCD // Requires ADC_KEYPAD_PIN to be assigned to an analog pin. + // This LCD is known to be susceptible to electrical interference + // which scrambles the display. Pressing any button clears it up. + // This is a LCD2004 display with 5 analog buttons. + +// +// Generic 16x2, 16x4, 20x2, or 20x4 character-based LCD. +// +//#define ULTRA_LCD + +//============================================================================= +//======================== LCD / Controller Selection ========================= +//===================== (I2C and Shift-Register LCDs) ===================== +//============================================================================= + +// +// CONTROLLER TYPE: I2C +// +// Note: These controllers require the installation of Arduino's LiquidCrystal_I2C +// library. For more info: https://github.com/kiyoshigawa/LiquidCrystal_I2C +// + +// +// Elefu RA Board Control Panel +// http://www.elefu.com/index.php?route=product/product&product_id=53 +// +//#define RA_CONTROL_PANEL + +// +// Sainsmart (YwRobot) LCD Displays +// +// These require F.Malpartida's LiquidCrystal_I2C library +// https://bitbucket.org/fmalpartida/new-liquidcrystal/wiki/Home +// +//#define LCD_SAINSMART_I2C_1602 +//#define LCD_SAINSMART_I2C_2004 + +// +// Generic LCM1602 LCD adapter +// +//#define LCM1602 + +// +// PANELOLU2 LCD with status LEDs, +// separate encoder and click inputs. +// +// Note: This controller requires Arduino's LiquidTWI2 library v1.2.3 or later. +// For more info: https://github.com/lincomatic/LiquidTWI2 +// +// Note: The PANELOLU2 encoder click input can either be directly connected to +// a pin (if BTN_ENC defined to != -1) or read through I2C (when BTN_ENC == -1). +// +//#define LCD_I2C_PANELOLU2 + +// +// Panucatt VIKI LCD with status LEDs, +// integrated click & L/R/U/D buttons, separate encoder inputs. +// +//#define LCD_I2C_VIKI + +// +// CONTROLLER TYPE: Shift register panels +// + +// +// 2-wire Non-latching LCD SR from https://goo.gl/aJJ4sH +// LCD configuration: http://reprap.org/wiki/SAV_3D_LCD +// +//#define SAV_3DLCD + +// +// 3-wire SR LCD with strobe using 74HC4094 +// https://github.com/mikeshub/SailfishLCD +// Uses the code directly from Sailfish +// +//#define FF_INTERFACEBOARD + +//============================================================================= +//======================= LCD / Controller Selection ======================= +//========================= (Graphical LCDs) ======================== +//============================================================================= + +// +// CONTROLLER TYPE: Graphical 128x64 (DOGM) +// +// IMPORTANT: The U8glib library is required for Graphical Display! +// https://github.com/olikraus/U8glib_Arduino +// + +// +// RepRapDiscount FULL GRAPHIC Smart Controller +// http://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller +// +//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER + +// +// ReprapWorld Graphical LCD +// https://reprapworld.com/?products_details&products_id/1218 +// +//#define REPRAPWORLD_GRAPHICAL_LCD + +// +// Activate one of these if you have a Panucatt Devices +// Viki 2.0 or mini Viki with Graphic LCD +// http://panucatt.com +// +//#define VIKI2 +//#define miniVIKI + +// +// MakerLab Mini Panel with graphic +// controller and SD support - http://reprap.org/wiki/Mini_panel +// +//#define MINIPANEL + +// +// MaKr3d Makr-Panel with graphic controller and SD support. +// http://reprap.org/wiki/MaKr3d_MaKrPanel +// +//#define MAKRPANEL + +// +// Adafruit ST7565 Full Graphic Controller. +// https://github.com/eboston/Adafruit-ST7565-Full-Graphic-Controller/ +// +//#define ELB_FULL_GRAPHIC_CONTROLLER + +// +// BQ LCD Smart Controller shipped by +// default with the BQ Hephestos 2 and Witbox 2. +// +//#define BQ_LCD_SMART_CONTROLLER + +// +// Cartesio UI +// http://mauk.cc/webshop/cartesio-shop/electronics/user-interface +// +//#define CARTESIO_UI + +// +// LCD for Melzi Card with Graphical LCD +// +//#define LCD_FOR_MELZI + +// +// Original Ulticontroller from Ultimaker 2 printer with SSD1309 I2C display and encoder +// https://github.com/Ultimaker/Ultimaker2/tree/master/1249_Ulticontroller_Board_(x1) +// +//#define ULTI_CONTROLLER + +// +// MKS MINI12864 with graphic controller and SD support +// https://reprap.org/wiki/MKS_MINI_12864 +// +//#define MKS_MINI_12864 + +// +// FYSETC variant of the MINI12864 graphic controller with SD support +// https://wiki.fysetc.com/Mini12864_Panel/ +// +//#define FYSETC_MINI_12864_X_X // Type C/D/E/F. No tunable RGB Backlight by default +//#define FYSETC_MINI_12864_1_2 // Type C/D/E/F. Simple RGB Backlight (always on) +//#define FYSETC_MINI_12864_2_0 // Type A/B. Discreet RGB Backlight +//#define FYSETC_MINI_12864_2_1 // Type A/B. Neopixel RGB Backlight + +// +// Factory display for Creality CR-10 +// https://www.aliexpress.com/item/Universal-LCD-12864-3D-Printer-Display-Screen-With-Encoder-For-CR-10-CR-7-Model/32833148327.html +// +// This is RAMPS-compatible using a single 10-pin connector. +// (For CR-10 owners who want to replace the Melzi Creality board but retain the display) +// +//#define CR10_STOCKDISPLAY + +// +// ANET and Tronxy Graphical Controller +// +// Anet 128x64 full graphics lcd with rotary encoder as used on Anet A6 +// A clone of the RepRapDiscount full graphics display but with +// different pins/wiring (see pins_ANET_10.h). +// +//#define ANET_FULL_GRAPHICS_LCD + +// +// AZSMZ 12864 LCD with SD +// https://www.aliexpress.com/store/product/3D-printer-smart-controller-SMART-RAMPS-OR-RAMPS-1-4-LCD-12864-LCD-control-panel-green/2179173_32213636460.html +// +//#define AZSMZ_12864 + +// +// Silvergate GLCD controller +// http://github.com/android444/Silvergate +// +//#define SILVER_GATE_GLCD_CONTROLLER + +//============================================================================= +//============================== OLED Displays ============================== +//============================================================================= + +// +// SSD1306 OLED full graphics generic display +// +//#define U8GLIB_SSD1306 + +// +// SAV OLEd LCD module support using either SSD1306 or SH1106 based LCD modules +// +//#define SAV_3DGLCD +#if ENABLED(SAV_3DGLCD) + #define U8GLIB_SSD1306 + //#define U8GLIB_SH1106 +#endif + +// +// TinyBoy2 128x64 OLED / Encoder Panel +// +//#define OLED_PANEL_TINYBOY2 + +// +// MKS OLED 1.3" 128 × 64 FULL GRAPHICS CONTROLLER +// http://reprap.org/wiki/MKS_12864OLED +// +// Tiny, but very sharp OLED display +// +//#define MKS_12864OLED // Uses the SH1106 controller (default) +//#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller + +// +// Einstart S OLED SSD1306 +// +//#define U8GLIB_SH1106_EINSTART + +// +// Overlord OLED display/controller with i2c buzzer and LEDs +// +//#define OVERLORD_OLED + +//============================================================================= +//========================== Extensible UI Displays =========================== +//============================================================================= + +// +// DGUS Touch Display with DWIN OS +// +//#define DGUS_LCD + +// +// Touch-screen LCD for Malyan M200 printers +// +//#define MALYAN_LCD + +// +// Third-party or vendor-customized controller interfaces. +// Sources should be installed in 'src/lcd/extensible_ui'. +// +//#define EXTENSIBLE_UI + +//============================================================================= +//=============================== Graphical TFTs ============================== +//============================================================================= + +// +// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.) +// +//#define FSMC_GRAPHICAL_TFT + +//============================================================================= +//============================ Other Controllers ============================ +//============================================================================= + +// +// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8 +// +//#define TOUCH_BUTTONS +#if ENABLED(TOUCH_BUTTONS) + #define XPT2046_X_CALIBRATION 12316 + #define XPT2046_Y_CALIBRATION -8981 + #define XPT2046_X_OFFSET -43 + #define XPT2046_Y_OFFSET 257 +#endif + +// +// RepRapWorld REPRAPWORLD_KEYPAD v1.1 +// http://reprapworld.com/?products_details&products_id=202&cPath=1591_1626 +// +// REPRAPWORLD_KEYPAD_MOVE_STEP sets how much should the robot move when a key +// is pressed, a value of 10.0 means 10mm per click. +// +//#define REPRAPWORLD_KEYPAD +//#define REPRAPWORLD_KEYPAD_MOVE_STEP 10.0 + +//============================================================================= +//=============================== Extra Features ============================== +//============================================================================= + +// @section extras + +// Increase the FAN PWM frequency. Removes the PWM noise but increases heating in the FET/Arduino +//#define FAST_PWM_FAN + +// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency +// which is not as annoying as with the hardware PWM. On the other hand, if this frequency +// is too low, you should also increment SOFT_PWM_SCALE. +//#define FAN_SOFT_PWM + +// Incrementing this by 1 will double the software PWM frequency, +// affecting heaters, and the fan if FAN_SOFT_PWM is enabled. +// However, control resolution will be halved for each increment; +// at zero value, there are 128 effective control positions. +// :[0,1,2,3,4,5,6,7] +#define SOFT_PWM_SCALE 0 + +// If SOFT_PWM_SCALE is set to a value higher than 0, dithering can +// be used to mitigate the associated resolution loss. If enabled, +// some of the PWM cycles are stretched so on average the desired +// duty cycle is attained. +//#define SOFT_PWM_DITHER + +// Temperature status LEDs that display the hotend and bed temperature. +// If all hotends, bed temperature, and target temperature are under 54C +// then the BLUE led is on. Otherwise the RED led is on. (1C hysteresis) +#define TEMP_STAT_LEDS + +// SkeinForge sends the wrong arc g-codes when using Arc Point as fillet procedure +//#define SF_ARC_FIX + +// Support for the BariCUDA Paste Extruder +//#define BARICUDA + +// Support for BlinkM/CyzRgb +//#define BLINKM + +// Support for PCA9632 PWM LED driver +//#define PCA9632 + +// Support for PCA9533 PWM LED driver +// https://github.com/mikeshub/SailfishRGB_LED +//#define PCA9533 + +/** + * RGB LED / LED Strip Control + * + * Enable support for an RGB LED connected to 5V digital pins, or + * an RGB Strip connected to MOSFETs controlled by digital pins. + * + * Adds the M150 command to set the LED (or LED strip) color. + * If pins are PWM capable (e.g., 4, 5, 6, 11) then a range of + * luminance values can be set from 0 to 255. + * For Neopixel LED an overall brightness parameter is also available. + * + * *** CAUTION *** + * LED Strips require a MOSFET Chip between PWM lines and LEDs, + * as the Arduino cannot handle the current the LEDs will require. + * Failure to follow this precaution can destroy your Arduino! + * NOTE: A separate 5V power supply is required! The Neopixel LED needs + * more current than the Arduino 5V linear regulator can produce. + * *** CAUTION *** + * + * LED Type. Enable only one of the following two options. + * + */ +//#define RGB_LED +//#define RGBW_LED + +#if EITHER(RGB_LED, RGBW_LED) + //#define RGB_LED_R_PIN 34 + //#define RGB_LED_G_PIN 43 + //#define RGB_LED_B_PIN 35 + //#define RGB_LED_W_PIN -1 +#endif + +// Support for Adafruit Neopixel LED driver +//#define NEOPIXEL_LED +#if ENABLED(NEOPIXEL_LED) + #define NEOPIXEL_TYPE NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h) + #define NEOPIXEL_PIN 4 // LED driving pin + //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE + //#define NEOPIXEL2_PIN 5 + #define NEOPIXEL_PIXELS 30 // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used + #define NEOPIXEL_IS_SEQUENTIAL // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once. + #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) + //#define NEOPIXEL_STARTUP_TEST // Cycle through colors at startup + + // Use a single Neopixel LED for static (background) lighting + //#define NEOPIXEL_BKGD_LED_INDEX 0 // Index of the LED to use + //#define NEOPIXEL_BKGD_COLOR { 255, 255, 255, 0 } // R, G, B, W +#endif + +/** + * Printer Event LEDs + * + * During printing, the LEDs will reflect the printer status: + * + * - Gradually change from blue to violet as the heated bed gets to target temp + * - Gradually change from violet to red as the hotend gets to temperature + * - Change to white to illuminate work surface + * - Change to green once print has finished + * - Turn off after the print has finished and the user has pushed a button + */ +#if ANY(BLINKM, RGB_LED, RGBW_LED, PCA9632, PCA9533, NEOPIXEL_LED) + #define PRINTER_EVENT_LEDS +#endif + +/** + * R/C SERVO support + * Sponsored by TrinityLabs, Reworked by codexmas + */ + +/** + * Number of servos + * + * For some servo-related options NUM_SERVOS will be set automatically. + * Set this manually if there are extra servos needing manual control. + * Leave undefined or set to 0 to entirely disable the servo subsystem. + */ +//#define NUM_SERVOS 3 // Servo index starts with 0 for M280 command + +// Delay (in milliseconds) before the next move will start, to give the servo time to reach its target angle. +// 300ms is a good value but you can try less delay. +// If the servo can't reach the requested position, increase it. +#define SERVO_DELAY { 300 } + +// Only power servos during movement, otherwise leave off to prevent jitter +//#define DEACTIVATE_SERVOS_AFTER_MOVE + +// Allow servo angle to be edited and saved to EEPROM +//#define EDITABLE_SERVO_ANGLES diff --git a/config/examples/HMS434/Configuration_adv.h b/config/examples/HMS434/Configuration_adv.h new file mode 100644 index 0000000000..ac27d24577 --- /dev/null +++ b/config/examples/HMS434/Configuration_adv.h @@ -0,0 +1,2565 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Configuration_adv.h + * + * Advanced settings. + * Only change these if you know exactly what you're doing. + * Some of these settings can damage your printer if improperly set! + * + * Basic settings can be found in Configuration.h + * + */ +#define CONFIGURATION_ADV_H_VERSION 020000 + +// @section temperature + +//=========================================================================== +//=============================Thermal Settings ============================ +//=========================================================================== + +// +// Custom Thermistor 1000 parameters +// +#if TEMP_SENSOR_0 == 1000 + #define HOTEND0_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND0_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND0_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_1 == 1000 + #define HOTEND1_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND1_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND1_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_2 == 1000 + #define HOTEND2_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND2_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND2_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_3 == 1000 + #define HOTEND3_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND3_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND3_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_4 == 1000 + #define HOTEND4_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND4_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND4_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_5 == 1000 + #define HOTEND5_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define HOTEND5_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define HOTEND5_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_BED == 1000 + #define BED_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define BED_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define BED_BETA 3950 // Beta value +#endif + +#if TEMP_SENSOR_CHAMBER == 1000 + #define CHAMBER_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor + #define CHAMBER_RESISTANCE_25C_OHMS 100000 // Resistance at 25C + #define CHAMBER_BETA 3950 // Beta value +#endif + +// +// Hephestos 2 24V heated bed upgrade kit. +// https://store.bq.com/en/heated-bed-kit-hephestos2 +// +//#define HEPHESTOS2_HEATED_BED_KIT +#if ENABLED(HEPHESTOS2_HEATED_BED_KIT) + #undef TEMP_SENSOR_BED + #define TEMP_SENSOR_BED 70 + #define HEATER_BED_INVERTING true +#endif + +/** + * Heated Chamber settings + */ +#if TEMP_SENSOR_CHAMBER + #define CHAMBER_MINTEMP 18 + #define CHAMBER_MAXTEMP 75 + #define TEMP_CHAMBER_HYSTERESIS 2 // (°C) Temperature proximity considered "close enough" to the target + //#define CHAMBER_LIMIT_SWITCHING + //#define HEATER_CHAMBER_PIN 44 // Chamber heater on/off pin + //#define HEATER_CHAMBER_INVERTING false +#endif + +#if DISABLED(PIDTEMPBED) + #define BED_CHECK_INTERVAL 5000 // ms between checks in bang-bang control + #if ENABLED(BED_LIMIT_SWITCHING) + #define BED_HYSTERESIS 2 // Only disable heating if T>target+BED_HYSTERESIS and enable heating if T>target-BED_HYSTERESIS + #endif +#endif + +/** + * Thermal Protection provides additional protection to your printer from damage + * and fire. Marlin always includes safe min and max temperature ranges which + * protect against a broken or disconnected thermistor wire. + * + * The issue: If a thermistor falls out, it will report the much lower + * temperature of the air in the room, and the the firmware will keep + * the heater on. + * + * The solution: Once the temperature reaches the target, start observing. + * If the temperature stays too far below the target (hysteresis) for too + * long (period), the firmware will halt the machine as a safety precaution. + * + * If you get false positives for "Thermal Runaway", increase + * THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD + */ +#if ENABLED(THERMAL_PROTECTION_HOTENDS) + #define THERMAL_PROTECTION_PERIOD 40 // Seconds + #define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius + + //#define ADAPTIVE_FAN_SLOWING // Slow part cooling fan if temperature drops + #if BOTH(ADAPTIVE_FAN_SLOWING, PIDTEMP) + //#define NO_FAN_SLOWING_IN_PID_TUNING // Don't slow fan speed during M303 + #endif + + /** + * Whenever an M104, M109, or M303 increases the target temperature, the + * firmware will wait for the WATCH_TEMP_PERIOD to expire. If the temperature + * hasn't increased by WATCH_TEMP_INCREASE degrees, the machine is halted and + * requires a hard reset. This test restarts with any M104/M109/M303, but only + * if the current temperature is far enough below the target for a reliable + * test. + * + * If you get false positives for "Heating failed", increase WATCH_TEMP_PERIOD + * and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set + * below 2. + */ + #define WATCH_TEMP_PERIOD 20 // Seconds + #define WATCH_TEMP_INCREASE 2 // Degrees Celsius +#endif + +/** + * Thermal Protection parameters for the bed are just as above for hotends. + */ +#if ENABLED(THERMAL_PROTECTION_BED) + #define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds + #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius + + /** + * As described above, except for the bed (M140/M190/M303). + */ + #define WATCH_BED_TEMP_PERIOD 60 // Seconds + #define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius +#endif + +/** + * Thermal Protection parameters for the heated chamber. + */ +#if ENABLED(THERMAL_PROTECTION_CHAMBER) + #define THERMAL_PROTECTION_CHAMBER_PERIOD 900 // Seconds + #define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius + + /** + * Heated chamber watch settings (M141/M191). + */ + #define WATCH_CHAMBER_TEMP_PERIOD 900 // Seconds + #define WATCH_CHAMBER_TEMP_INCREASE 2 // Degrees Celsius +#endif + +#if ENABLED(PIDTEMP) + // Add an experimental additional term to the heater power, proportional to the extrusion speed. + // A well-chosen Kc value should add just enough power to melt the increased material volume. + //#define PID_EXTRUSION_SCALING + #if ENABLED(PID_EXTRUSION_SCALING) + #define DEFAULT_Kc (100) //heating power=Kc*(e_speed) + #define LPQ_MAX_LEN 50 + #endif +#endif + +/** + * Automatic Temperature: + * The hotend target temperature is calculated by all the buffered lines of gcode. + * The maximum buffered steps/sec of the extruder motor is called "se". + * Start autotemp mode with M109 S B F + * The target temperature is set to mintemp+factor*se[steps/sec] and is limited by + * mintemp and maxtemp. Turn this off by executing M109 without F* + * Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp. + * On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode + */ +#define AUTOTEMP +#if ENABLED(AUTOTEMP) + #define AUTOTEMP_OLDWEIGHT 0.98 +#endif + +// Show extra position information in M114 +//#define M114_DETAIL + +// Show Temperature ADC value +// Enable for M105 to include ADC values read from temperature sensors. +//#define SHOW_TEMP_ADC_VALUES + +/** + * High Temperature Thermistor Support + * + * Thermistors able to support high temperature tend to have a hard time getting + * good readings at room and lower temperatures. This means HEATER_X_RAW_LO_TEMP + * will probably be caught when the heating element first turns on during the + * preheating process, which will trigger a min_temp_error as a safety measure + * and force stop everything. + * To circumvent this limitation, we allow for a preheat time (during which, + * min_temp_error won't be triggered) and add a min_temp buffer to handle + * aberrant readings. + * + * If you want to enable this feature for your hotend thermistor(s) + * uncomment and set values > 0 in the constants below + */ + +// The number of consecutive low temperature errors that can occur +// before a min_temp_error is triggered. (Shouldn't be more than 10.) +//#define MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED 0 + +// The number of milliseconds a hotend will preheat before starting to check +// the temperature. This value should NOT be set to the time it takes the +// hot end to reach the target temperature, but the time it takes to reach +// the minimum temperature your thermistor can read. The lower the better/safer. +// This shouldn't need to be more than 30 seconds (30000) +//#define MILLISECONDS_PREHEAT_TIME 0 + +// @section extruder + +// Extruder runout prevention. +// If the machine is idle and the temperature over MINTEMP +// then extrude some filament every couple of SECONDS. +//#define EXTRUDER_RUNOUT_PREVENT +#if ENABLED(EXTRUDER_RUNOUT_PREVENT) + #define EXTRUDER_RUNOUT_MINTEMP 190 + #define EXTRUDER_RUNOUT_SECONDS 30 + #define EXTRUDER_RUNOUT_SPEED 1500 // (mm/m) + #define EXTRUDER_RUNOUT_EXTRUDE 5 // (mm) +#endif + +// @section temperature + +// Calibration for AD595 / AD8495 sensor to adjust temperature measurements. +// The final temperature is calculated as (measuredTemp * GAIN) + OFFSET. +#define TEMP_SENSOR_AD595_OFFSET 0.0 +#define TEMP_SENSOR_AD595_GAIN 2.0 // compensate for 3V3 ref voltage +#define TEMP_SENSOR_AD8495_OFFSET 0.0 +#define TEMP_SENSOR_AD8495_GAIN 1.0 + +/** + * Controller Fan + * To cool down the stepper drivers and MOSFETs. + * + * The fan will turn on automatically whenever any stepper is enabled + * and turn off after a set period after all steppers are turned off. + */ +//#define USE_CONTROLLER_FAN +#if ENABLED(USE_CONTROLLER_FAN) + //#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan + #define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled + #define CONTROLLERFAN_SPEED 255 // 255 == full speed +#endif + +// When first starting the main fan, run it at full speed for the +// given number of milliseconds. This gets the fan spinning reliably +// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu) +//#define FAN_KICKSTART_TIME 100 + +/** + * PWM Fan Scaling + * + * Define the min/max speeds for PWM fans (as set with M106). + * + * With these options the M106 0-255 value range is scaled to a subset + * to ensure that the fan has enough power to spin, or to run lower + * current fans with higher current. (e.g., 5V/12V fans with 12V/24V) + * Value 0 always turns off the fan. + * + * Define one or both of these to override the default 0-255 range. + */ +//#define FAN_MIN_PWM 50 +//#define FAN_MAX_PWM 128 + +/** + * FAST PWM FAN Settings + * + * Use to change the FAST FAN PWM frequency (if enabled in Configuration.h) + * Combinations of PWM Modes, prescale values and TOP resolutions are used internally to produce a + * frequency as close as possible to the desired frequency. + * + * FAST_PWM_FAN_FREQUENCY [undefined by default] + * Set this to your desired frequency. + * If left undefined this defaults to F = F_CPU/(2*255*1) + * ie F = 31.4 Khz on 16 MHz microcontrollers or F = 39.2 KHz on 20 MHz microcontrollers + * These defaults are the same as with the old FAST_PWM_FAN implementation - no migration is required + * NOTE: Setting very low frequencies (< 10 Hz) may result in unexpected timer behavior. + * + * USE_OCR2A_AS_TOP [undefined by default] + * Boards that use TIMER2 for PWM have limitations resulting in only a few possible frequencies on TIMER2: + * 16MHz MCUs: [62.5KHz, 31.4KHz (default), 7.8KHz, 3.92KHz, 1.95KHz, 977Hz, 488Hz, 244Hz, 60Hz, 122Hz, 30Hz] + * 20MHz MCUs: [78.1KHz, 39.2KHz (default), 9.77KHz, 4.9KHz, 2.44KHz, 1.22KHz, 610Hz, 305Hz, 153Hz, 76Hz, 38Hz] + * A greater range can be achieved by enabling USE_OCR2A_AS_TOP. But note that this option blocks the use of + * PWM on pin OC2A. Only use this option if you don't need PWM on 0C2A. (Check your schematic.) + * USE_OCR2A_AS_TOP sacrifices duty cycle control resolution to achieve this broader range of frequencies. + */ +#if ENABLED(FAST_PWM_FAN) + //#define FAST_PWM_FAN_FREQUENCY 31400 + //#define USE_OCR2A_AS_TOP +#endif + +// @section extruder + +/** + * Extruder cooling fans + * + * Extruder auto fans automatically turn on when their extruders' + * temperatures go above EXTRUDER_AUTO_FAN_TEMPERATURE. + * + * Your board's pins file specifies the recommended pins. Override those here + * or set to -1 to disable completely. + * + * Multiple extruders can be assigned to the same pin in which case + * the fan will turn on when any selected extruder is above the threshold. + */ + +#define EXTRUDER_AUTO_FAN_TEMPERATURE 35 +#define EXTRUDER_AUTO_FAN_SPEED 255 // 255 == full speed +#define CHAMBER_AUTO_FAN_TEMPERATURE 28 +#define CHAMBER_AUTO_FAN_SPEED 255 + +/** + * Part-Cooling Fan Multiplexer + * + * This feature allows you to digitally multiplex the fan output. + * The multiplexer is automatically switched at tool-change. + * Set FANMUX[012]_PINs below for up to 2, 4, or 8 multiplexed fans. + */ +#define FANMUX0_PIN -1 +#define FANMUX1_PIN -1 +#define FANMUX2_PIN -1 + +/** + * M355 Case Light on-off / brightness + */ +//#define CASE_LIGHT_ENABLE +#if ENABLED(CASE_LIGHT_ENABLE) + //#define CASE_LIGHT_PIN 4 // Override the default pin if needed + #define INVERT_CASE_LIGHT false // Set true if Case Light is ON when pin is LOW + #define CASE_LIGHT_DEFAULT_ON true // Set default power-up state on + #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105 // Set default power-up brightness (0-255, requires PWM pin) + //#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu + //#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting. + //#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED. + #if ENABLED(CASE_LIGHT_USE_NEOPIXEL) + #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White } + #endif +#endif + +// @section homing + +// If you want endstops to stay on (by default) even when not homing +// enable this option. Override at any time with M120, M121. +//#define ENDSTOPS_ALWAYS_ON_DEFAULT + +// @section extras + +//#define Z_LATE_ENABLE // Enable Z the last moment. Needed if your Z driver overheats. + +// Employ an external closed loop controller. Override pins here if needed. +//#define EXTERNAL_CLOSED_LOOP_CONTROLLER +#if ENABLED(EXTERNAL_CLOSED_LOOP_CONTROLLER) + //#define CLOSED_LOOP_ENABLE_PIN -1 + //#define CLOSED_LOOP_MOVE_COMPLETE_PIN -1 +#endif + +/** + * Dual Steppers / Dual Endstops + * + * This section will allow you to use extra E drivers to drive a second motor for X, Y, or Z axes. + * + * For example, set X_DUAL_STEPPER_DRIVERS setting to use a second motor. If the motors need to + * spin in opposite directions set INVERT_X2_VS_X_DIR. If the second motor needs its own endstop + * set X_DUAL_ENDSTOPS. This can adjust for "racking." Use X2_USE_ENDSTOP to set the endstop plug + * that should be used for the second endstop. Extra endstops will appear in the output of 'M119'. + * + * Use X_DUAL_ENDSTOP_ADJUSTMENT to adjust for mechanical imperfection. After homing both motors + * this offset is applied to the X2 motor. To find the offset home the X axis, and measure the error + * in X2. Dual endstop offsets can be set at runtime with 'M666 X Y Z'. + */ + +//#define X_DUAL_STEPPER_DRIVERS +#if ENABLED(X_DUAL_STEPPER_DRIVERS) + #define INVERT_X2_VS_X_DIR true // Set 'true' if X motors should rotate in opposite directions + //#define X_DUAL_ENDSTOPS + #if ENABLED(X_DUAL_ENDSTOPS) + #define X2_USE_ENDSTOP _XMAX_ + #define X_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Y_DUAL_STEPPER_DRIVERS +#if ENABLED(Y_DUAL_STEPPER_DRIVERS) + #define INVERT_Y2_VS_Y_DIR true // Set 'true' if Y motors should rotate in opposite directions + //#define Y_DUAL_ENDSTOPS + #if ENABLED(Y_DUAL_ENDSTOPS) + #define Y2_USE_ENDSTOP _YMAX_ + #define Y_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Z_DUAL_STEPPER_DRIVERS +#if ENABLED(Z_DUAL_STEPPER_DRIVERS) + //#define Z_DUAL_ENDSTOPS + #if ENABLED(Z_DUAL_ENDSTOPS) + #define Z2_USE_ENDSTOP _XMAX_ + #define Z_DUAL_ENDSTOPS_ADJUSTMENT 0 + #endif +#endif + +//#define Z_TRIPLE_STEPPER_DRIVERS +#if ENABLED(Z_TRIPLE_STEPPER_DRIVERS) + //#define Z_TRIPLE_ENDSTOPS + #if ENABLED(Z_TRIPLE_ENDSTOPS) + #define Z2_USE_ENDSTOP _XMAX_ + #define Z3_USE_ENDSTOP _YMAX_ + #define Z_TRIPLE_ENDSTOPS_ADJUSTMENT2 0 + #define Z_TRIPLE_ENDSTOPS_ADJUSTMENT3 0 + #endif +#endif + +/** + * Dual X Carriage + * + * This setup has two X carriages that can move independently, each with its own hotend. + * The carriages can be used to print an object with two colors or materials, or in + * "duplication mode" it can print two identical or X-mirrored objects simultaneously. + * The inactive carriage is parked automatically to prevent oozing. + * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis. + * By default the X2 stepper is assigned to the first unused E plug on the board. + * + * The following Dual X Carriage modes can be selected with M605 S: + * + * 0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel + * results as long as it supports dual X-carriages. (M605 S0) + * + * 1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so + * that additional slicer support is not required. (M605 S1) + * + * 2 : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with + * the first X-carriage and extruder, to print 2 copies of the same object at the same time. + * Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and + * follow with M605 S2 to initiate duplicated movement. + * + * 3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates + * the movement of the first except the second extruder is reversed in the X axis. + * Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and + * follow with M605 S3 to initiate mirrored movement. + */ +//#define DUAL_X_CARRIAGE +#if ENABLED(DUAL_X_CARRIAGE) + #define X1_MIN_POS X_MIN_POS // Set to X_MIN_POS + #define X1_MAX_POS X_BED_SIZE // Set a maximum so the first X-carriage can't hit the parked second X-carriage + #define X2_MIN_POS 80 // Set a minimum to ensure the second X-carriage can't hit the parked first X-carriage + #define X2_MAX_POS 353 // Set this to the distance between toolheads when both heads are homed + #define X2_HOME_DIR 1 // Set to 1. The second X-carriage always homes to the maximum endstop position + #define X2_HOME_POS X2_MAX_POS // Default X2 home position. Set to X2_MAX_POS. + // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software + // override for X2_HOME_POS. This also allow recalibration of the distance between the two endstops + // without modifying the firmware (through the "M218 T1 X???" command). + // Remember: you should set the second extruder x-offset to 0 in your slicer. + + // This is the default power-up mode which can be later using M605. + #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_AUTO_PARK_MODE + + // Default x offset in duplication mode (typically set to half print bed width) + #define DEFAULT_DUPLICATION_X_OFFSET 100 + +#endif // DUAL_X_CARRIAGE + +// Activate a solenoid on the active extruder with M380. Disable all with M381. +// Define SOL0_PIN, SOL1_PIN, etc., for each extruder that has a solenoid. +//#define EXT_SOLENOID + +// @section homing + +// Homing hits each endstop, retracts by these distances, then does a slower bump. +#define X_HOME_BUMP_MM 5 +#define Y_HOME_BUMP_MM 5 +#define Z_HOME_BUMP_MM 2 +#define HOMING_BUMP_DIVISOR { 2, 2, 4 } // Re-Bump Speed Divisor (Divides the Homing Feedrate) +//#define QUICK_HOME // If homing includes X and Y, do a diagonal move initially +//#define HOMING_BACKOFF_MM { 2, 2, 2 } // (mm) Move away from the endstops after homing + +// When G28 is called, this option will make Y home before X +#define HOME_Y_BEFORE_X + +// Enable this if X or Y can't home without homing the other axis first. +//#define CODEPENDENT_XY_HOMING + +#if ENABLED(BLTOUCH) + /** + * Either: Use the defaults (recommended) or: For special purposes, use the following DEFINES + * Do not activate settings that the probe might not understand. Clones might misunderstand + * advanced commands. + * + * Note: If the probe is not deploying, check a "Cmd: Reset" and "Cmd: Self-Test" and then + * check the wiring of the BROWN, RED and ORANGE wires. + * + * Note: If the trigger signal of your probe is not being recognized, it has been very often + * because the BLACK and WHITE wires needed to be swapped. They are not "interchangeable" + * like they would be with a real switch. So please check the wiring first. + * + * Settings for all BLTouch and clone probes: + */ + + // Safety: The probe needs time to recognize the command. + // Minimum command delay (ms). Enable and increase if needed. + //#define BLTOUCH_DELAY 500 + + /** + * Settings for BLTOUCH Classic 1.2, 1.3 or BLTouch Smart 1.0, 2.0, 2.2, 3.0, 3.1, and most clones: + */ + + // Feature: Switch into SW mode after a deploy. It makes the output pulse longer. Can be useful + // in special cases, like noisy or filtered input configurations. + //#define BLTOUCH_FORCE_SW_MODE + + /** + * Settings for BLTouch Smart 3.0 and 3.1 + * Summary: + * - Voltage modes: 5V and OD (open drain - "logic voltage free") output modes + * - High-Speed mode + * - Disable LCD voltage options + */ + + /** + * Danger: Don't activate 5V mode unless attached to a 5V-tolerant controller! + * V3.0 or 3.1: Set default mode to 5V mode at Marlin startup. + * If disabled, OD mode is the hard-coded default on 3.0 + * On startup, Marlin will compare its eeprom to this vale. If the selected mode + * differs, a mode set eeprom write will be completed at initialization. + * Use the option below to force an eeprom write to a V3.1 probe regardless. + */ + //#define BLTOUCH_SET_5V_MODE + + /** + * Safety: Activate if connecting a probe with an unknown voltage mode. + * V3.0: Set a probe into mode selected above at Marlin startup. Required for 5V mode on 3.0 + * V3.1: Force a probe with unknown mode into selected mode at Marlin startup ( = Probe EEPROM write ) + * To preserve the life of the probe, use this once then turn it off and re-flash. + */ + //#define BLTOUCH_FORCE_MODE_SET + + /** + * Use "HIGH SPEED" mode for probing. + * Danger: Disable if your probe sometimes fails. Only suitable for stable well-adjusted systems. + * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function + * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state. + */ + //#define BLTOUCH_HS_MODE + + // Safety: Enable voltage mode settings in the LCD menu. + //#define BLTOUCH_LCD_VOLTAGE_MENU + +#endif // BLTOUCH + +/** + * Z Steppers Auto-Alignment + * Add the G34 command to align multiple Z steppers using a bed probe. + */ +//#define Z_STEPPER_AUTO_ALIGN +#if ENABLED(Z_STEPPER_AUTO_ALIGN) + // Define probe X and Y positions for Z1, Z2 [, Z3] + #define Z_STEPPER_ALIGN_X { 10, 150, 290 } + #define Z_STEPPER_ALIGN_Y { 290, 10, 290 } + // Set number of iterations to align + #define Z_STEPPER_ALIGN_ITERATIONS 3 + // Enable to restore leveling setup after operation + #define RESTORE_LEVELING_AFTER_G34 + + // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm + #define G34_MAX_GRADE 5 // (%) Maximum incline G34 will handle + + // Use the amplification factor to de-/increase correction step. + // In case the stepper (spindle) position is further out than the test point + // Use a value > 1. NOTE: This may cause instability + #define Z_STEPPER_ALIGN_AMP 1.0 + // Stop criterion. If the accuracy is better than this stop iterating early + #define Z_STEPPER_ALIGN_ACC 0.02 +#endif + +// @section machine + +#define AXIS_RELATIVE_MODES { false, false, false, false } + +// Add a Duplicate option for well-separated conjoined nozzles +//#define MULTI_NOZZLE_DUPLICATION + +// By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step. +#define INVERT_X_STEP_PIN false +#define INVERT_Y_STEP_PIN false +#define INVERT_Z_STEP_PIN false +#define INVERT_E_STEP_PIN false + +// Default stepper release if idle. Set to 0 to deactivate. +// Steppers will shut down DEFAULT_STEPPER_DEACTIVE_TIME seconds after the last move when DISABLE_INACTIVE_? is true. +// Time can be set by M18 and M84. +#define DEFAULT_STEPPER_DEACTIVE_TIME 120 +#define DISABLE_INACTIVE_X true +#define DISABLE_INACTIVE_Y true +#define DISABLE_INACTIVE_Z true // Set to false if the nozzle will fall down on your printed part when print has finished. +#define DISABLE_INACTIVE_E true + +#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate +#define DEFAULT_MINTRAVELFEEDRATE 0.0 + +//#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated + +// @section lcd + +#if EITHER(ULTIPANEL, EXTENSIBLE_UI) + #define MANUAL_FEEDRATE { 50*60, 50*60, 4*60, 60 } // Feedrates for manual moves along X, Y, Z, E from panel + #define SHORT_MANUAL_Z_MOVE 0.025 // (mm) Smallest manual Z move (< 0.1mm) + #if ENABLED(ULTIPANEL) + #define MANUAL_E_MOVES_RELATIVE // Display extruder move distance rather than "position" + #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen + #endif +#endif + +// @section extras + +// minimum time in microseconds that a movement needs to take if the buffer is emptied. +#define DEFAULT_MINSEGMENTTIME 20000 + +// If defined the movements slow down when the look ahead buffer is only half full +#define SLOWDOWN + +// Frequency limit +// See nophead's blog for more info +// Not working O +//#define XY_FREQUENCY_LIMIT 15 + +// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end +// of the buffer and all stops. This should not be much greater than zero and should only be changed +// if unwanted behavior is observed on a user's machine when running at very slow speeds. +#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s) + +// +// Backlash Compensation +// Adds extra movement to axes on direction-changes to account for backlash. +// +//#define BACKLASH_COMPENSATION +#if ENABLED(BACKLASH_COMPENSATION) + // Define values for backlash distance and correction. + // If BACKLASH_GCODE is enabled these values are the defaults. + #define BACKLASH_DISTANCE_MM { 0, 0, 0 } // (mm) + #define BACKLASH_CORRECTION 0.0 // 0.0 = no correction; 1.0 = full correction + + // Set BACKLASH_SMOOTHING_MM to spread backlash correction over multiple segments + // to reduce print artifacts. (Enabling this is costly in memory and computation!) + //#define BACKLASH_SMOOTHING_MM 3 // (mm) + + // Add runtime configuration and tuning of backlash values (M425) + //#define BACKLASH_GCODE + + #if ENABLED(BACKLASH_GCODE) + // Measure the Z backlash when probing (G29) and set with "M425 Z" + #define MEASURE_BACKLASH_WHEN_PROBING + + #if ENABLED(MEASURE_BACKLASH_WHEN_PROBING) + // When measuring, the probe will move up to BACKLASH_MEASUREMENT_LIMIT + // mm away from point of contact in BACKLASH_MEASUREMENT_RESOLUTION + // increments while checking for the contact to be broken. + #define BACKLASH_MEASUREMENT_LIMIT 0.5 // (mm) + #define BACKLASH_MEASUREMENT_RESOLUTION 0.005 // (mm) + #define BACKLASH_MEASUREMENT_FEEDRATE Z_PROBE_SPEED_SLOW // (mm/m) + #endif + #endif +#endif + +/** + * Automatic backlash, position and hotend offset calibration + * + * Enable G425 to run automatic calibration using an electrically- + * conductive cube, bolt, or washer mounted on the bed. + * + * G425 uses the probe to touch the top and sides of the calibration object + * on the bed and measures and/or correct positional offsets, axis backlash + * and hotend offsets. + * + * Note: HOTEND_OFFSET and CALIBRATION_OBJECT_CENTER must be set to within + * ±5mm of true values for G425 to succeed. + */ +//#define CALIBRATION_GCODE +#if ENABLED(CALIBRATION_GCODE) + + #define CALIBRATION_MEASUREMENT_RESOLUTION 0.01 // mm + + #define CALIBRATION_FEEDRATE_SLOW 60 // mm/m + #define CALIBRATION_FEEDRATE_FAST 1200 // mm/m + #define CALIBRATION_FEEDRATE_TRAVEL 3000 // mm/m + + // The following parameters refer to the conical section of the nozzle tip. + #define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm + #define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm + + // Uncomment to enable reporting (required for "G425 V", but consumes PROGMEM). + //#define CALIBRATION_REPORTING + + // The true location and dimension the cube/bolt/washer on the bed. + #define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0} // mm + #define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0} // mm + + // Comment out any sides which are unreachable by the probe. For best + // auto-calibration results, all sides must be reachable. + #define CALIBRATION_MEASURE_RIGHT + #define CALIBRATION_MEASURE_FRONT + #define CALIBRATION_MEASURE_LEFT + #define CALIBRATION_MEASURE_BACK + + // Probing at the exact top center only works if the center is flat. If + // probing on a screwhead or hollow washer, probe near the edges. + //#define CALIBRATION_MEASURE_AT_TOP_EDGES + + // Define pin which is read during calibration + #ifndef CALIBRATION_PIN + #define CALIBRATION_PIN -1 // Override in pins.h or set to -1 to use your Z endstop + #define CALIBRATION_PIN_INVERTING false // Set to true to invert the pin + //#define CALIBRATION_PIN_PULLDOWN + #define CALIBRATION_PIN_PULLUP + #endif +#endif + +/** + * Adaptive Step Smoothing increases the resolution of multi-axis moves, particularly at step frequencies + * below 1kHz (for AVR) or 10kHz (for ARM), where aliasing between axes in multi-axis moves causes audible + * vibration and surface artifacts. The algorithm adapts to provide the best possible step smoothing at the + * lowest stepping frequencies. + */ +//#define ADAPTIVE_STEP_SMOOTHING + +/** + * Custom Microstepping + * Override as-needed for your setup. Up to 3 MS pins are supported. + */ +//#define MICROSTEP1 LOW,LOW,LOW +//#define MICROSTEP2 HIGH,LOW,LOW +//#define MICROSTEP4 LOW,HIGH,LOW +//#define MICROSTEP8 HIGH,HIGH,LOW +//#define MICROSTEP16 LOW,LOW,HIGH +//#define MICROSTEP32 HIGH,LOW,HIGH + +// Microstep setting (Only functional when stepper driver microstep pins are connected to MCU. +#define MICROSTEP_MODES { 16, 16, 16, 16, 16, 16 } // [1,2,4,8,16] + +/** + * @section stepper motor current + * + * Some boards have a means of setting the stepper motor current via firmware. + * + * The power on motor currents are set by: + * PWM_MOTOR_CURRENT - used by MINIRAMBO & ULTIMAIN_2 + * known compatible chips: A4982 + * DIGIPOT_MOTOR_CURRENT - used by BQ_ZUM_MEGA_3D, RAMBO & SCOOVO_X9H + * known compatible chips: AD5206 + * DAC_MOTOR_CURRENT_DEFAULT - used by PRINTRBOARD_REVF & RIGIDBOARD_V2 + * known compatible chips: MCP4728 + * DIGIPOT_I2C_MOTOR_CURRENTS - used by 5DPRINT, AZTEEG_X3_PRO, AZTEEG_X5_MINI_WIFI, MIGHTYBOARD_REVE + * known compatible chips: MCP4451, MCP4018 + * + * Motor currents can also be set by M907 - M910 and by the LCD. + * M907 - applies to all. + * M908 - BQ_ZUM_MEGA_3D, RAMBO, PRINTRBOARD_REVF, RIGIDBOARD_V2 & SCOOVO_X9H + * M909, M910 & LCD - only PRINTRBOARD_REVF & RIGIDBOARD_V2 + */ +//#define PWM_MOTOR_CURRENT { 1300, 1300, 1250 } // Values in milliamps +//#define DIGIPOT_MOTOR_CURRENT { 135,135,135,135,135 } // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A) +//#define DAC_MOTOR_CURRENT_DEFAULT { 70, 80, 90, 80 } // Default drive percent - X, Y, Z, E axis + +// Use an I2C based DIGIPOT (e.g., Azteeg X3 Pro) +//#define DIGIPOT_I2C +#if ENABLED(DIGIPOT_I2C) && !defined(DIGIPOT_I2C_ADDRESS_A) + /** + * Common slave addresses: + * + * A (A shifted) B (B shifted) IC + * Smoothie 0x2C (0x58) 0x2D (0x5A) MCP4451 + * AZTEEG_X3_PRO 0x2C (0x58) 0x2E (0x5C) MCP4451 + * AZTEEG_X5_MINI 0x2C (0x58) 0x2E (0x5C) MCP4451 + * AZTEEG_X5_MINI_WIFI 0x58 0x5C MCP4451 + * MIGHTYBOARD_REVE 0x2F (0x5E) MCP4018 + */ + #define DIGIPOT_I2C_ADDRESS_A 0x2C // unshifted slave address for first DIGIPOT + #define DIGIPOT_I2C_ADDRESS_B 0x2D // unshifted slave address for second DIGIPOT +#endif + +//#define DIGIPOT_MCP4018 // Requires library from https://github.com/stawel/SlowSoftI2CMaster +#define DIGIPOT_I2C_NUM_CHANNELS 8 // 5DPRINT: 4 AZTEEG_X3_PRO: 8 MKS SBASE: 5 +// Actual motor currents in Amps. The number of entries must match DIGIPOT_I2C_NUM_CHANNELS. +// These correspond to the physical drivers, so be mindful if the order is changed. +#define DIGIPOT_I2C_MOTOR_CURRENTS { 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0, 1.0 } // AZTEEG_X3_PRO + +//=========================================================================== +//=============================Additional Features=========================== +//=========================================================================== + +// @section lcd + +// Change values more rapidly when the encoder is rotated faster +#define ENCODER_RATE_MULTIPLIER +#if ENABLED(ENCODER_RATE_MULTIPLIER) + #define ENCODER_10X_STEPS_PER_SEC 30 // (steps/s) Encoder rate for 10x speed + #define ENCODER_100X_STEPS_PER_SEC 80 // (steps/s) Encoder rate for 100x speed +#endif + +// Play a beep when the feedrate is changed from the Status Screen +//#define BEEP_ON_FEEDRATE_CHANGE +#if ENABLED(BEEP_ON_FEEDRATE_CHANGE) + #define FEEDRATE_CHANGE_BEEP_DURATION 10 + #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 +#endif + +// Include a page of printer information in the LCD Main Menu +//#define LCD_INFO_MENU +#if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages +#endif + +// Scroll a longer status message into view +//#define STATUS_MESSAGE_SCROLLING + +// On the Info Screen, display XY with one decimal place when possible +//#define LCD_DECIMAL_SMALL_XY + +// The timeout (in ms) to return to the status screen from sub-menus +//#define LCD_TIMEOUT_TO_STATUS 15000 + +// Add an 'M73' G-code to set the current percentage +//#define LCD_SET_PROGRESS_MANUALLY + +#if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS + //#define LCD_PROGRESS_BAR // Show a progress bar on HD44780 LCDs for SD printing + #if ENABLED(LCD_PROGRESS_BAR) + #define PROGRESS_BAR_BAR_TIME 2000 // (ms) Amount of time to show the bar + #define PROGRESS_BAR_MSG_TIME 3000 // (ms) Amount of time to show the status message + #define PROGRESS_MSG_EXPIRE 0 // (ms) Amount of time to retain the status message (0=forever) + //#define PROGRESS_MSG_ONCE // Show the message for MSG_TIME then clear it + //#define LCD_PROGRESS_BAR_TEST // Add a menu item to test the progress bar + #endif +#endif + +/** + * LED Control Menu + * Enable this feature to add LED Control to the LCD menu + */ +//#define LED_CONTROL_MENU +#if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif +#endif // LED_CONTROL_MENU + +#if ENABLED(SDSUPPORT) + + // Some RAMPS and other boards don't detect when an SD card is inserted. You can work + // around this by connecting a push button or single throw switch to the pin defined + // as SD_DETECT_PIN in your board's pins definitions. + // This setting should be disabled unless you are using a push button, pulling the pin to ground. + // Note: This is always disabled for ULTIPANEL (except ELB_FULL_GRAPHIC_CONTROLLER). + #define SD_DETECT_INVERTED + + #define SD_FINISHED_STEPPERRELEASE true // Disable steppers when SD Print is finished + #define SD_FINISHED_RELEASECOMMAND "M84 X Y Z E" // You might want to keep the Z enabled so your bed stays in place. + + // Reverse SD sort to show "more recent" files first, according to the card's FAT. + // Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended. + #define SDCARD_RATHERRECENTFIRST + + #define SD_MENU_CONFIRM_START // Confirm the selected SD file before printing + + //#define MENU_ADDAUTOSTART // Add a menu option to run auto#.g files + + #define EVENT_GCODE_SD_STOP "G28XY" // G-code to run on Stop Print (e.g., "G28XY" or "G27") + + /** + * Continue after Power-Loss (Creality3D) + * + * Store the current state to the SD Card at the start of each layer + * during SD printing. If the recovery file is found at boot time, present + * an option on the LCD screen to continue the print from the last-known + * point in the file. + */ + //#define POWER_LOSS_RECOVERY + #if ENABLED(POWER_LOSS_RECOVERY) + //#define POWER_LOSS_PIN 44 // Pin to detect power loss + //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume + //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. + + // Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card, + // especially with "vase mode" printing. Set too high and vases cannot be continued. + #define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data + #endif + + /** + * Sort SD file listings in alphabetical order. + * + * With this option enabled, items on SD cards will be sorted + * by name for easier navigation. + * + * By default... + * + * - Use the slowest -but safest- method for sorting. + * - Folders are sorted to the top. + * - The sort key is statically allocated. + * - No added G-code (M34) support. + * - 40 item sorting limit. (Items after the first 40 are unsorted.) + * + * SD sorting uses static allocation (as set by SDSORT_LIMIT), allowing the + * compiler to calculate the worst-case usage and throw an error if the SRAM + * limit is exceeded. + * + * - SDSORT_USES_RAM provides faster sorting via a static directory buffer. + * - SDSORT_USES_STACK does the same, but uses a local stack-based buffer. + * - SDSORT_CACHE_NAMES will retain the sorted file listing in RAM. (Expensive!) + * - SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible. (Use with caution!) + */ + //#define SDCARD_SORT_ALPHA + + // SD Card Sorting options + #if ENABLED(SDCARD_SORT_ALPHA) + #define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). Costs 27 bytes each. + #define FOLDER_SORTING -1 // -1=above 0=none 1=below + #define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 g-code. + #define SDSORT_USES_RAM false // Pre-allocate a static array for faster pre-sorting. + #define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.) + #define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option. + #define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use! + #define SDSORT_CACHE_VFATS 2 // Maximum number of 13-byte VFAT entries to use for sorting. + // Note: Only affects SCROLL_LONG_FILENAMES with SDSORT_CACHE_NAMES but not SDSORT_DYNAMIC_RAM. + #endif + + // This allows hosts to request long names for files and folders with M33 + //#define LONG_FILENAME_HOST_SUPPORT + + // Enable this option to scroll long filenames in the SD card menu + //#define SCROLL_LONG_FILENAMES + + // Leave the heaters on after Stop Print (not recommended!) + //#define SD_ABORT_NO_COOLDOWN + + /** + * This option allows you to abort SD printing when any endstop is triggered. + * This feature must be enabled with "M540 S1" or from the LCD menu. + * To have any effect, endstops must be enabled during SD printing. + */ + //#define SD_ABORT_ON_ENDSTOP_HIT + + /** + * This option makes it easier to print the same SD Card file again. + * On print completion the LCD Menu will open with the file selected. + * You can just click to start the print, or navigate elsewhere. + */ + //#define SD_REPRINT_LAST_SELECTED_FILE + + /** + * Auto-report SdCard status with M27 S + */ + //#define AUTO_REPORT_SD_STATUS + + /** + * Support for USB thumb drives using an Arduino USB Host Shield or + * equivalent MAX3421E breakout board. The USB thumb drive will appear + * to Marlin as an SD card. + * + * The MAX3421E must be assigned the same pins as the SD card reader, with + * the following pin mapping: + * + * SCLK, MOSI, MISO --> SCLK, MOSI, MISO + * INT --> SD_DETECT_PIN + * SS --> SDSS + */ + //#define USB_FLASH_DRIVE_SUPPORT + #if ENABLED(USB_FLASH_DRIVE_SUPPORT) + #define USB_CS_PIN SDSS + #define USB_INTR_PIN SD_DETECT_PIN + #endif + + /** + * When using a bootloader that supports SD-Firmware-Flashing, + * add a menu item to activate SD-FW-Update on the next reboot. + * + * Requires ATMEGA2560 (Arduino Mega) + * + * Tested with this bootloader: + * https://github.com/FleetProbe/MicroBridge-Arduino-ATMega2560 + */ + //#define SD_FIRMWARE_UPDATE + #if ENABLED(SD_FIRMWARE_UPDATE) + #define SD_FIRMWARE_UPDATE_EEPROM_ADDR 0x1FF + #define SD_FIRMWARE_UPDATE_ACTIVE_VALUE 0xF0 + #define SD_FIRMWARE_UPDATE_INACTIVE_VALUE 0xFF + #endif + + // Add an optimized binary file transfer mode, initiated with 'M28 B1' + //#define BINARY_FILE_TRANSFER + + #if HAS_SDCARD_CONNECTION + /** + * Set this option to one of the following (or the board's defaults apply): + * + * LCD - Use the SD drive in the external LCD controller. + * ONBOARD - Use the SD drive on the control board. (No SD_DETECT_PIN. M21 to init.) + * CUSTOM_CABLE - Use a custom cable to access the SD (as defined in a pins file). + * + * :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ] + */ + //#define SDCARD_CONNECTION LCD + #endif + +#endif // SDSUPPORT + +/** + * By default an onboard SD card reader may be shared as a USB mass- + * storage device. This option hides the SD card from the host PC. + */ +//#define NO_SD_HOST_DRIVE // Disable SD Card access over USB (for security). + +/** + * Additional options for Graphical Displays + * + * Use the optimizations here to improve printing performance, + * which can be adversely affected by graphical display drawing, + * especially when doing several short moves, and when printing + * on DELTA and SCARA machines. + * + * Some of these options may result in the display lagging behind + * controller events, as there is a trade-off between reliable + * printing performance versus fast display updates. + */ +#if HAS_GRAPHICAL_LCD + // Show SD percentage next to the progress bar + //#define DOGM_SD_PERCENT + + // Enable to save many cycles by drawing a hollow frame on the Info Screen + #define XYZ_HOLLOW_FRAME + + // Enable to save many cycles by drawing a hollow frame on Menu Screens + #define MENU_HOLLOW_FRAME + + // A bigger font is available for edit items. Costs 3120 bytes of PROGMEM. + // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. + //#define USE_BIG_EDIT_FONT + + // A smaller font may be used on the Info Screen. Costs 2300 bytes of PROGMEM. + // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese. + //#define USE_SMALL_INFOFONT + + // Enable this option and reduce the value to optimize screen updates. + // The normal delay is 10µs. Use the lowest value that still gives a reliable display. + //#define DOGM_SPI_DELAY_US 5 + + // Swap the CW/CCW indicators in the graphics overlay + //#define OVERLAY_GFX_REVERSE + + /** + * ST7920-based LCDs can emulate a 16 x 4 character display using + * the ST7920 character-generator for very fast screen updates. + * Enable LIGHTWEIGHT_UI to use this special display mode. + * + * Since LIGHTWEIGHT_UI has limited space, the position and status + * message occupy the same line. Set STATUS_EXPIRE_SECONDS to the + * length of time to display the status message before clearing. + * + * Set STATUS_EXPIRE_SECONDS to zero to never clear the status. + * This will prevent position updates from being displayed. + */ + #if ENABLED(U8GLIB_ST7920) + //#define LIGHTWEIGHT_UI + #if ENABLED(LIGHTWEIGHT_UI) + #define STATUS_EXPIRE_SECONDS 20 + #endif + #endif + + /** + * Status (Info) Screen customizations + * These options may affect code size and screen render time. + * Custom status screens can forcibly override these settings. + */ + //#define STATUS_COMBINE_HEATERS // Use combined heater images instead of separate ones + //#define STATUS_HOTEND_NUMBERLESS // Use plain hotend icons instead of numbered ones (with 2+ hotends) + #define STATUS_HOTEND_INVERTED // Show solid nozzle bitmaps when heating (Requires STATUS_HOTEND_ANIM) + #define STATUS_HOTEND_ANIM // Use a second bitmap to indicate hotend heating + #define STATUS_BED_ANIM // Use a second bitmap to indicate bed heating + #define STATUS_CHAMBER_ANIM // Use a second bitmap to indicate chamber heating + //#define STATUS_ALT_BED_BITMAP // Use the alternative bed bitmap + //#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap + //#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames + //#define STATUS_HEAT_PERCENT // Show heating in a progress bar + //#define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash) + + // Frivolous Game Options + //#define MARLIN_BRICKOUT + //#define MARLIN_INVADERS + //#define MARLIN_SNAKE + //#define GAMES_EASTER_EGG // Add extra blank lines above the "Games" sub-menu + +#endif // HAS_GRAPHICAL_LCD + +// @section safety + +/** + * The watchdog hardware timer will do a reset and disable all outputs + * if the firmware gets too overloaded to read the temperature sensors. + * + * If you find that watchdog reboot causes your AVR board to hang forever, + * enable WATCHDOG_RESET_MANUAL to use a custom timer instead of WDTO. + * NOTE: This method is less reliable as it can only catch hangups while + * interrupts are enabled. + */ +#define USE_WATCHDOG +#if ENABLED(USE_WATCHDOG) + //#define WATCHDOG_RESET_MANUAL +#endif + +// @section lcd + +/** + * Babystepping enables movement of the axes by tiny increments without changing + * the current position values. This feature is used primarily to adjust the Z + * axis in the first layer of a print in real-time. + * + * Warning: Does not respect endstops! + */ +#define BABYSTEPPING +#if ENABLED(BABYSTEPPING) + //#define BABYSTEP_WITHOUT_HOMING + //#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA! + #define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way + #define BABYSTEP_MULTIPLICATOR 16 // Babysteps are very small. Increase for faster motion. + + //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping. + #if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING) + #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds. + // Note: Extra time may be added to mitigate controller latency. + //#define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement). + //#define MOVE_Z_WHEN_IDLE // Jump to the move Z menu on doubleclick when printer is idle. + #if ENABLED(MOVE_Z_WHEN_IDLE) + #define MOVE_Z_IDLE_MULTIPLICATOR 1 // Multiply 1mm by this factor for the move step size. + #endif + #endif + + //#define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28 + + //#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping + #if ENABLED(BABYSTEP_ZPROBE_OFFSET) + //#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets + //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor + #endif +#endif + +// @section extruder + +/** + * Linear Pressure Control v1.5 + * + * Assumption: advance [steps] = k * (delta velocity [steps/s]) + * K=0 means advance disabled. + * + * NOTE: K values for LIN_ADVANCE 1.5 differ from earlier versions! + * + * Set K around 0.22 for 3mm PLA Direct Drive with ~6.5cm between the drive gear and heatbreak. + * Larger K values will be needed for flexible filament and greater distances. + * If this algorithm produces a higher speed offset than the extruder can handle (compared to E jerk) + * print acceleration will be reduced during the affected moves to keep within the limit. + * + * See http://marlinfw.org/docs/features/lin_advance.html for full instructions. + * Mention @Sebastianv650 on GitHub to alert the author of any issues. + */ +#define LIN_ADVANCE +#if ENABLED(LIN_ADVANCE) + //#define EXTRA_LIN_ADVANCE_K // Enable for second linear advance constants + #define LIN_ADVANCE_K 0.02 // Unit: mm compression per 1mm/s extruder speed + //#define LA_DEBUG // If enabled, this will generate debug information output over USB. +#endif + +// @section leveling + +#if EITHER(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL) + // Override the mesh area if the automatic (max) area is too large + //#define MESH_MIN_X MESH_INSET + //#define MESH_MIN_Y MESH_INSET + //#define MESH_MAX_X X_BED_SIZE - (MESH_INSET) + //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET) +#endif + +/** + * Repeatedly attempt G29 leveling until it succeeds. + * Stop after G29_MAX_RETRIES attempts. + */ +//#define G29_RETRY_AND_RECOVER +#if ENABLED(G29_RETRY_AND_RECOVER) + #define G29_MAX_RETRIES 3 + #define G29_HALT_ON_FAILURE + /** + * Specify the GCODE commands that will be executed when leveling succeeds, + * between attempts, and after the maximum number of retries have been tried. + */ + #define G29_SUCCESS_COMMANDS "M117 Bed leveling done." + #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0" + #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1" + +#endif + +// @section extras + +// +// G2/G3 Arc Support +// +#define ARC_SUPPORT // Disable this feature to save ~3226 bytes +#if ENABLED(ARC_SUPPORT) + #define MM_PER_ARC_SEGMENT 1 // Length of each arc segment + #define MIN_ARC_SEGMENTS 24 // Minimum number of segments in a complete circle + #define N_ARC_CORRECTION 25 // Number of interpolated segments between corrections + //#define ARC_P_CIRCLES // Enable the 'P' parameter to specify complete circles + //#define CNC_WORKSPACE_PLANES // Allow G2/G3 to operate in XY, ZX, or YZ planes +#endif + +// Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes. +//#define BEZIER_CURVE_SUPPORT + +/** + * G38 Probe Target + * + * This option adds G38.2 and G38.3 (probe towards target) + * and optionally G38.4 and G38.5 (probe away from target). + * Set MULTIPLE_PROBING for G38 to probe more than once. + */ +//#define G38_PROBE_TARGET +#if ENABLED(G38_PROBE_TARGET) + //#define G38_PROBE_AWAY // Include G38.4 and G38.5 to probe away from target + #define G38_MINIMUM_MOVE 0.0275 // (mm) Minimum distance that will produce a move. +#endif + +// Moves (or segments) with fewer steps than this will be joined with the next move +#define MIN_STEPS_PER_SEGMENT 6 + +/** + * Minimum delay after setting the stepper DIR (in ns) + * 0 : No delay (Expect at least 10µS since one Stepper ISR must transpire) + * 20 : Minimum for TMC2xxx drivers + * 200 : Minimum for A4988 drivers + * 400 : Minimum for A5984 drivers + * 500 : Minimum for LV8729 drivers (guess, no info in datasheet) + * 650 : Minimum for DRV8825 drivers + * 1500 : Minimum for TB6600 drivers (guess, no info in datasheet) + * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet) + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MINIMUM_STEPPER_DIR_DELAY 650 + +/** + * Minimum stepper driver pulse width (in µs) + * 0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers + * 0 : Minimum 500ns for LV8729, adjusted in stepper.h + * 1 : Minimum for A4988 and A5984 stepper drivers + * 2 : Minimum for DRV8825 stepper drivers + * 3 : Minimum for TB6600 stepper drivers + * 30 : Minimum for TB6560 stepper drivers + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MINIMUM_STEPPER_PULSE 2 + +/** + * Maximum stepping rate (in Hz) the stepper driver allows + * If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE) + * 500000 : Maximum for A4988 stepper driver + * 400000 : Maximum for TMC2xxx stepper drivers + * 250000 : Maximum for DRV8825 stepper driver + * 200000 : Maximum for LV8729 stepper driver + * 150000 : Maximum for TB6600 stepper driver + * 15000 : Maximum for TB6560 stepper driver + * + * Override the default value based on the driver type set in Configuration.h. + */ +//#define MAXIMUM_STEPPER_RATE 250000 + +// @section temperature + +// Control heater 0 and heater 1 in parallel. +//#define HEATERS_PARALLEL + +//=========================================================================== +//================================= Buffers ================================= +//=========================================================================== + +// @section hidden + +// The number of linear motions that can be in the plan at any give time. +// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2 (e.g. 8, 16, 32) because shifts and ors are used to do the ring-buffering. +#if ENABLED(SDSUPPORT) + #define BLOCK_BUFFER_SIZE 8 // SD,LCD,Buttons take more memory, block buffer needs to be smaller +#else + #define BLOCK_BUFFER_SIZE 8 // maximize block buffer +#endif + +// @section serial + +// The ASCII buffer for serial input +#define MAX_CMD_SIZE 96 +#define BUFSIZE 4 + +// Transmission to Host Buffer Size +// To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0. +// To buffer a simple "ok" you need 4 bytes. +// For ADVANCED_OK (M105) you need 32 bytes. +// For debug-echo: 128 bytes for the optimal speed. +// Other output doesn't need to be that speedy. +// :[0, 2, 4, 8, 16, 32, 64, 128, 256] +#define TX_BUFFER_SIZE 32 + +// Host Receive Buffer Size +// Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough. +// To use flow control, set this buffer size to at least 1024 bytes. +// :[0, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1024, 2048] +#define RX_BUFFER_SIZE 1024 + +#if RX_BUFFER_SIZE >= 1024 + // Enable to have the controller send XON/XOFF control characters to + // the host to signal the RX buffer is becoming full. + #define SERIAL_XON_XOFF +#endif + +// Add M575 G-code to change the baud rate +//#define BAUD_RATE_GCODE + +#if ENABLED(SDSUPPORT) + // Enable this option to collect and display the maximum + // RX queue usage after transferring a file to SD. + //#define SERIAL_STATS_MAX_RX_QUEUED + + // Enable this option to collect and display the number + // of dropped bytes after a file transfer to SD. + //#define SERIAL_STATS_DROPPED_RX +#endif + +// Enable an emergency-command parser to intercept certain commands as they +// enter the serial receive buffer, so they cannot be blocked. +// Currently handles M108, M112, M410 +// Does not work on boards using AT90USB (USBCON) processors! +#define EMERGENCY_PARSER + +// Bad Serial-connections can miss a received command by sending an 'ok' +// Therefore some clients abort after 30 seconds in a timeout. +// Some other clients start sending commands while receiving a 'wait'. +// This "wait" is only sent when the buffer is empty. 1 second is a good value here. +//#define NO_TIMEOUTS 1000 // Milliseconds + +// Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary. +#define ADVANCED_OK + +// Printrun may have trouble receiving long strings all at once. +// This option inserts short delays between lines of serial output. +#define SERIAL_OVERRUN_PROTECTION + +// @section extras + +/** + * Extra Fan Speed + * Adds a secondary fan speed for each print-cooling fan. + * 'M106 P T3-255' : Set a secondary speed for + * 'M106 P T2' : Use the set secondary speed + * 'M106 P T1' : Restore the previous fan speed + */ +//#define EXTRA_FAN_SPEED + +/** + * Firmware-based and LCD-controlled retract + * + * Add G10 / G11 commands for automatic firmware-based retract / recover. + * Use M207 and M208 to define parameters for retract / recover. + * + * Use M209 to enable or disable auto-retract. + * With auto-retract enabled, all G1 E moves within the set range + * will be converted to firmware-based retract/recover moves. + * + * Be sure to turn off auto-retract during filament change. + * + * Note that M207 / M208 / M209 settings are saved to EEPROM. + * + */ +//#define FWRETRACT +#if ENABLED(FWRETRACT) + #define FWRETRACT_AUTORETRACT // costs ~500 bytes of PROGMEM + #if ENABLED(FWRETRACT_AUTORETRACT) + #define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over + #define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion + #endif + #define RETRACT_LENGTH 3 // Default retract length (positive mm) + #define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change + #define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s) + #define RETRACT_ZRAISE 0 // Default retract Z-raise (mm) + #define RETRACT_RECOVER_LENGTH 0 // Default additional recover length (mm, added to retract length when recovering) + #define RETRACT_RECOVER_LENGTH_SWAP 0 // Default additional swap recover length (mm, added to retract length when recovering from extruder change) + #define RETRACT_RECOVER_FEEDRATE 8 // Default feedrate for recovering from retraction (mm/s) + #define RETRACT_RECOVER_FEEDRATE_SWAP 8 // Default feedrate for recovering from swap retraction (mm/s) + #if ENABLED(MIXING_EXTRUDER) + //#define RETRACT_SYNC_MIXING // Retract and restore all mixing steppers simultaneously + #endif +#endif + +/** + * Universal tool change settings. + * Applies to all types of extruders except where explicitly noted. + */ +#if EXTRUDERS > 1 + // Z raise distance for tool-change, as needed for some extruders + #define TOOLCHANGE_ZRAISE 2 // (mm) + //#define TOOLCHANGE_NO_RETURN // Never return to the previous position on tool-change + + // Retract and prime filament on tool-change + //#define TOOLCHANGE_FILAMENT_SWAP + #if ENABLED(TOOLCHANGE_FILAMENT_SWAP) + #define TOOLCHANGE_FIL_SWAP_LENGTH 12 // (mm) + #define TOOLCHANGE_FIL_EXTRA_PRIME 2 // (mm) + #define TOOLCHANGE_FIL_SWAP_RETRACT_SPEED 3600 // (mm/m) + #define TOOLCHANGE_FIL_SWAP_PRIME_SPEED 3600 // (mm/m) + #endif + + /** + * Position to park head during tool change. + * Doesn't apply to SWITCHING_TOOLHEAD, DUAL_X_CARRIAGE, or PARKING_EXTRUDER + */ + //#define TOOLCHANGE_PARK + #if ENABLED(TOOLCHANGE_PARK) + #define TOOLCHANGE_PARK_XY { X_MIN_POS + 10, Y_MIN_POS + 10 } + #define TOOLCHANGE_PARK_XY_FEEDRATE 6000 // (mm/m) + #endif +#endif + +/** + * Advanced Pause + * Experimental feature for filament change support and for parking the nozzle when paused. + * Adds the GCode M600 for initiating filament change. + * If PARK_HEAD_ON_PAUSE enabled, adds the GCode M125 to pause printing and park the nozzle. + * + * Requires an LCD display. + * Requires NOZZLE_PARK_FEATURE. + * This feature is required for the default FILAMENT_RUNOUT_SCRIPT. + */ +#define ADVANCED_PAUSE_FEATURE +#if ENABLED(ADVANCED_PAUSE_FEATURE) + #define PAUSE_PARK_RETRACT_FEEDRATE 30 // (mm/s) Initial retract feedrate. + #define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract. + // This short retract is done immediately, before parking the nozzle. + #define FILAMENT_CHANGE_UNLOAD_FEEDRATE 30 // (mm/s) Unload filament feedrate. This can be pretty fast. + #define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. + #define FILAMENT_CHANGE_UNLOAD_LENGTH 0 // (mm) The length of filament for a complete unload. + // For Bowden, the full length of the tube and nozzle. + // For direct drive, the full length of the nozzle. + // Set to 0 for manual unloading. + #define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load. + #define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material. + // 0 to disable start loading and skip to fast load only + #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast. + #define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate. + #define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle. + // For Bowden, the full length of the tube and nozzle. + // For direct drive, the full length of the nozzle. + //#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted. + #define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate. + #define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading. + // Set to 0 for manual extrusion. + // Filament can be extruded repeatedly from the Filament Change menu + // until extrusion is consistent, and to purge old filament. + #define ADVANCED_PAUSE_RESUME_PRIME 0 // (mm) Extra distance to prime nozzle after returning from park. + //#define ADVANCED_PAUSE_FANS_PAUSE // Turn off print-cooling fans while the machine is paused. + + // Filament Unload does a Retract, Delay, and Purge first: + #define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length. + #define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract. + #define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged. + + #define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety. + #define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed. + #define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change. + + //#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change. + //#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change + + //#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu. + //#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302) +#endif + +// @section tmc + +/** + * TMC26X Stepper Driver options + * + * The TMC26XStepper library is required for this stepper driver. + * https://github.com/trinamic/TMC26XStepper + */ +#if HAS_DRIVER(TMC26X) + + #if AXIS_DRIVER_TYPE_X(TMC26X) + #define X_MAX_CURRENT 1000 // (mA) + #define X_SENSE_RESISTOR 91 // (mOhms) + #define X_MICROSTEPS 16 // Number of microsteps + #endif + + #if AXIS_DRIVER_TYPE_X2(TMC26X) + #define X2_MAX_CURRENT 1000 + #define X2_SENSE_RESISTOR 91 + #define X2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Y(TMC26X) + #define Y_MAX_CURRENT 1000 + #define Y_SENSE_RESISTOR 91 + #define Y_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Y2(TMC26X) + #define Y2_MAX_CURRENT 1000 + #define Y2_SENSE_RESISTOR 91 + #define Y2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z(TMC26X) + #define Z_MAX_CURRENT 1000 + #define Z_SENSE_RESISTOR 91 + #define Z_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z2(TMC26X) + #define Z2_MAX_CURRENT 1000 + #define Z2_SENSE_RESISTOR 91 + #define Z2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_Z3(TMC26X) + #define Z3_MAX_CURRENT 1000 + #define Z3_SENSE_RESISTOR 91 + #define Z3_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E0(TMC26X) + #define E0_MAX_CURRENT 1000 + #define E0_SENSE_RESISTOR 91 + #define E0_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E1(TMC26X) + #define E1_MAX_CURRENT 1000 + #define E1_SENSE_RESISTOR 91 + #define E1_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E2(TMC26X) + #define E2_MAX_CURRENT 1000 + #define E2_SENSE_RESISTOR 91 + #define E2_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E3(TMC26X) + #define E3_MAX_CURRENT 1000 + #define E3_SENSE_RESISTOR 91 + #define E3_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E4(TMC26X) + #define E4_MAX_CURRENT 1000 + #define E4_SENSE_RESISTOR 91 + #define E4_MICROSTEPS 16 + #endif + + #if AXIS_DRIVER_TYPE_E5(TMC26X) + #define E5_MAX_CURRENT 1000 + #define E5_SENSE_RESISTOR 91 + #define E5_MICROSTEPS 16 + #endif + +#endif // TMC26X + +// @section tmc_smart + +/** + * To use TMC2130, TMC2160, TMC2660, TMC5130, TMC5160 stepper drivers in SPI mode + * connect your SPI pins to the hardware SPI interface on your board and define + * the required CS pins in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 + * pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.). + * You may also use software SPI if you wish to use general purpose IO pins. + * + * To use TMC2208 stepper UART-configurable stepper drivers connect #_SERIAL_TX_PIN + * to the driver side PDN_UART pin with a 1K resistor. + * To use the reading capabilities, also connect #_SERIAL_RX_PIN to PDN_UART without + * a resistor. + * The drivers can also be used with hardware serial. + * + * TMCStepper library is required to use TMC stepper drivers. + * https://github.com/teemuatlut/TMCStepper + */ +#if HAS_TRINAMIC + + #define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current + #define INTERPOLATE true // Interpolate X/Y/Z_MICROSTEPS to 256 + + #if AXIS_IS_TMC(X) + #define X_CURRENT 800 // (mA) RMS current. Multiply by 1.414 for peak current. + #define X_MICROSTEPS 16 // 0..256 + #define X_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(X2) + #define X2_CURRENT 800 + #define X2_MICROSTEPS 16 + #define X2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Y) + #define Y_CURRENT 800 + #define Y_MICROSTEPS 16 + #define Y_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Y2) + #define Y2_CURRENT 800 + #define Y2_MICROSTEPS 16 + #define Y2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Z) + #define Z_CURRENT 800 + #define Z_MICROSTEPS 16 + #define Z_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Z2) + #define Z2_CURRENT 800 + #define Z2_MICROSTEPS 16 + #define Z2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(Z3) + #define Z3_CURRENT 800 + #define Z3_MICROSTEPS 16 + #define Z3_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E0) + #define E0_CURRENT 800 + #define E0_MICROSTEPS 16 + #define E0_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E1) + #define E1_CURRENT 800 + #define E1_MICROSTEPS 16 + #define E1_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E2) + #define E2_CURRENT 800 + #define E2_MICROSTEPS 16 + #define E2_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E3) + #define E3_CURRENT 800 + #define E3_MICROSTEPS 16 + #define E3_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E4) + #define E4_CURRENT 800 + #define E4_MICROSTEPS 16 + #define E4_RSENSE 0.11 + #endif + + #if AXIS_IS_TMC(E5) + #define E5_CURRENT 800 + #define E5_MICROSTEPS 16 + #define E5_RSENSE 0.11 + #endif + + /** + * Override default SPI pins for TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160 drivers here. + * The default pins can be found in your board's pins file. + */ + //#define X_CS_PIN -1 + //#define Y_CS_PIN -1 + //#define Z_CS_PIN -1 + //#define X2_CS_PIN -1 + //#define Y2_CS_PIN -1 + //#define Z2_CS_PIN -1 + //#define Z3_CS_PIN -1 + //#define E0_CS_PIN -1 + //#define E1_CS_PIN -1 + //#define E2_CS_PIN -1 + //#define E3_CS_PIN -1 + //#define E4_CS_PIN -1 + //#define E5_CS_PIN -1 + + /** + * Software option for SPI driven drivers (TMC2130, TMC2160, TMC2660, TMC5130 and TMC5160). + * The default SW SPI pins are defined the respective pins files, + * but you can override or define them here. + */ + //#define TMC_USE_SW_SPI + //#define TMC_SW_MOSI -1 + //#define TMC_SW_MISO -1 + //#define TMC_SW_SCK -1 + + /** + * Four TMC2209 drivers can use the same HW/SW serial port with hardware configured addresses. + * Set the address using jumpers on pins MS1 and MS2. + * Address | MS1 | MS2 + * 0 | LOW | LOW + * 1 | HIGH | LOW + * 2 | LOW | HIGH + * 3 | HIGH | HIGH + * + * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers + * on the same serial port, either here or in your board's pins file. + */ + #define X_SLAVE_ADDRESS 0 + #define Y_SLAVE_ADDRESS 0 + #define Z_SLAVE_ADDRESS 0 + #define X2_SLAVE_ADDRESS 0 + #define Y2_SLAVE_ADDRESS 0 + #define Z2_SLAVE_ADDRESS 0 + #define Z3_SLAVE_ADDRESS 0 + #define E0_SLAVE_ADDRESS 0 + #define E1_SLAVE_ADDRESS 0 + #define E2_SLAVE_ADDRESS 0 + #define E3_SLAVE_ADDRESS 0 + #define E4_SLAVE_ADDRESS 0 + #define E5_SLAVE_ADDRESS 0 + + /** + * Software enable + * + * Use for drivers that do not use a dedicated enable pin, but rather handle the same + * function through a communication line such as SPI or UART. + */ + //#define SOFTWARE_DRIVER_ENABLE + + /** + * TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only + * Use Trinamic's ultra quiet stepping mode. + * When disabled, Marlin will use spreadCycle stepping mode. + */ + #define STEALTHCHOP_XY + #define STEALTHCHOP_Z + #define STEALTHCHOP_E + + /** + * Optimize spreadCycle chopper parameters by using predefined parameter sets + * or with the help of an example included in the library. + * Provided parameter sets are + * CHOPPER_DEFAULT_12V + * CHOPPER_DEFAULT_19V + * CHOPPER_DEFAULT_24V + * CHOPPER_DEFAULT_36V + * CHOPPER_PRUSAMK3_24V // Imported parameters from the official Prusa firmware for MK3 (24V) + * CHOPPER_MARLIN_119 // Old defaults from Marlin v1.1.9 + * + * Define you own with + * { , , hysteresis_start[1..8] } + */ + #define CHOPPER_TIMING CHOPPER_DEFAULT_12V + + /** + * Monitor Trinamic drivers for error conditions, + * like overtemperature and short to ground. + * In the case of overtemperature Marlin can decrease the driver current until error condition clears. + * Other detected conditions can be used to stop the current print. + * Relevant g-codes: + * M906 - Set or get motor current in milliamps using axis codes X, Y, Z, E. Report values if no axis codes given. + * M911 - Report stepper driver overtemperature pre-warn condition. + * M912 - Clear stepper driver overtemperature pre-warn condition flag. + * M122 - Report driver parameters (Requires TMC_DEBUG) + */ + //#define MONITOR_DRIVER_STATUS + + #if ENABLED(MONITOR_DRIVER_STATUS) + #define CURRENT_STEP_DOWN 50 // [mA] + #define REPORT_CURRENT_CHANGE + #define STOP_ON_ERROR + #endif + + /** + * TMC2130, TMC2160, TMC2208, TMC2209, TMC5130 and TMC5160 only + * The driver will switch to spreadCycle when stepper speed is over HYBRID_THRESHOLD. + * This mode allows for faster movements at the expense of higher noise levels. + * STEALTHCHOP_(XY|Z|E) must be enabled to use HYBRID_THRESHOLD. + * M913 X/Y/Z/E to live tune the setting + */ + //#define HYBRID_THRESHOLD + + #define X_HYBRID_THRESHOLD 100 // [mm/s] + #define X2_HYBRID_THRESHOLD 100 + #define Y_HYBRID_THRESHOLD 100 + #define Y2_HYBRID_THRESHOLD 100 + #define Z_HYBRID_THRESHOLD 3 + #define Z2_HYBRID_THRESHOLD 3 + #define Z3_HYBRID_THRESHOLD 3 + #define E0_HYBRID_THRESHOLD 30 + #define E1_HYBRID_THRESHOLD 30 + #define E2_HYBRID_THRESHOLD 30 + #define E3_HYBRID_THRESHOLD 30 + #define E4_HYBRID_THRESHOLD 30 + #define E5_HYBRID_THRESHOLD 30 + + /** + * Use StallGuard2 to home / probe X, Y, Z. + * + * TMC2130, TMC2160, TMC2209, TMC2660, TMC5130, and TMC5160 only + * Connect the stepper driver's DIAG1 pin to the X/Y endstop pin. + * X, Y, and Z homing will always be done in spreadCycle mode. + * + * X/Y/Z_STALL_SENSITIVITY is used to tune the trigger sensitivity. + * Use M914 X Y Z to live-adjust the sensitivity. + * Higher: LESS sensitive. (Too high => failure to trigger) + * Lower: MORE sensitive. (Too low => false positives) + * + * It is recommended to set [XYZ]_HOME_BUMP_MM to 0. + * + * SPI_ENDSTOPS *** Beta feature! *** TMC2130 Only *** + * Poll the driver through SPI to determine load when homing. + * Removes the need for a wire from DIAG1 to an endstop pin. + * + * IMPROVE_HOMING_RELIABILITY tunes acceleration and jerk when + * homing and adds a guard period for endstop triggering. + */ + //#define SENSORLESS_HOMING // StallGuard capable drivers only + + /** + * Use StallGuard2 to probe the bed with the nozzle. + * + * CAUTION: This could cause damage to machines that use a lead screw or threaded rod + * to move the Z axis. Take extreme care when attempting to enable this feature. + */ + //#define SENSORLESS_PROBING // StallGuard capable drivers only + + #if EITHER(SENSORLESS_HOMING, SENSORLESS_PROBING) + // TMC2209: 0...255. TMC2130: -64...63 + #define X_STALL_SENSITIVITY 8 + #define Y_STALL_SENSITIVITY 8 + //#define Z_STALL_SENSITIVITY 8 + //#define SPI_ENDSTOPS // TMC2130 only + //#define IMPROVE_HOMING_RELIABILITY + #endif + + /** + * Beta feature! + * Create a 50/50 square wave step pulse optimal for stepper drivers. + */ + //#define SQUARE_WAVE_STEPPING + + /** + * Enable M122 debugging command for TMC stepper drivers. + * M122 S0/1 will enable continous reporting. + */ + //#define TMC_DEBUG + + /** + * You can set your own advanced settings by filling in predefined functions. + * A list of available functions can be found on the library github page + * https://github.com/teemuatlut/TMCStepper + * + * Example: + * #define TMC_ADV() { \ + * stepperX.diag0_temp_prewarn(1); \ + * stepperY.interpolate(0); \ + * } + */ + #define TMC_ADV() { } + +#endif // HAS_TRINAMIC + +// @section L6470 + +/** + * L6470 Stepper Driver options + * + * Arduino-L6470 library (0.7.0 or higher) is required for this stepper driver. + * https://github.com/ameyer/Arduino-L6470 + * + * Requires the following to be defined in your pins_YOUR_BOARD file + * L6470_CHAIN_SCK_PIN + * L6470_CHAIN_MISO_PIN + * L6470_CHAIN_MOSI_PIN + * L6470_CHAIN_SS_PIN + * L6470_RESET_CHAIN_PIN (optional) + */ +#if HAS_DRIVER(L6470) + + //#define L6470_CHITCHAT // Display additional status info + + #if AXIS_DRIVER_TYPE_X(L6470) + #define X_MICROSTEPS 128 // Number of microsteps (VALID: 1, 2, 4, 8, 16, 32, 128) + #define X_OVERCURRENT 2000 // (mA) Current where the driver detects an over current (VALID: 375 x (1 - 16) - 6A max - rounds down) + #define X_STALLCURRENT 1500 // (mA) Current where the driver detects a stall (VALID: 31.25 * (1-128) - 4A max - rounds down) + #define X_MAX_VOLTAGE 127 // 0-255, Maximum effective voltage seen by stepper + #define X_CHAIN_POS 0 // Position in SPI chain, 0=Not in chain, 1=Nearest MOSI + #endif + + #if AXIS_DRIVER_TYPE_X2(L6470) + #define X2_MICROSTEPS 128 + #define X2_OVERCURRENT 2000 + #define X2_STALLCURRENT 1500 + #define X2_MAX_VOLTAGE 127 + #define X2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Y(L6470) + #define Y_MICROSTEPS 128 + #define Y_OVERCURRENT 2000 + #define Y_STALLCURRENT 1500 + #define Y_MAX_VOLTAGE 127 + #define Y_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Y2(L6470) + #define Y2_MICROSTEPS 128 + #define Y2_OVERCURRENT 2000 + #define Y2_STALLCURRENT 1500 + #define Y2_MAX_VOLTAGE 127 + #define Y2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Z(L6470) + #define Z_MICROSTEPS 128 + #define Z_OVERCURRENT 2000 + #define Z_STALLCURRENT 1500 + #define Z_MAX_VOLTAGE 127 + #define Z_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Z2(L6470) + #define Z2_MICROSTEPS 128 + #define Z2_OVERCURRENT 2000 + #define Z2_STALLCURRENT 1500 + #define Z2_MAX_VOLTAGE 127 + #define Z2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_Z3(L6470) + #define Z3_MICROSTEPS 128 + #define Z3_OVERCURRENT 2000 + #define Z3_STALLCURRENT 1500 + #define Z3_MAX_VOLTAGE 127 + #define Z3_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E0(L6470) + #define E0_MICROSTEPS 128 + #define E0_OVERCURRENT 2000 + #define E0_STALLCURRENT 1500 + #define E0_MAX_VOLTAGE 127 + #define E0_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E1(L6470) + #define E1_MICROSTEPS 128 + #define E1_OVERCURRENT 2000 + #define E1_STALLCURRENT 1500 + #define E1_MAX_VOLTAGE 127 + #define E1_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E2(L6470) + #define E2_MICROSTEPS 128 + #define E2_OVERCURRENT 2000 + #define E2_STALLCURRENT 1500 + #define E2_MAX_VOLTAGE 127 + #define E2_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E3(L6470) + #define E3_MICROSTEPS 128 + #define E3_OVERCURRENT 2000 + #define E3_STALLCURRENT 1500 + #define E3_MAX_VOLTAGE 127 + #define E3_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E4(L6470) + #define E4_MICROSTEPS 128 + #define E4_OVERCURRENT 2000 + #define E4_STALLCURRENT 1500 + #define E4_MAX_VOLTAGE 127 + #define E4_CHAIN_POS 0 + #endif + + #if AXIS_DRIVER_TYPE_E5(L6470) + #define E5_MICROSTEPS 128 + #define E5_OVERCURRENT 2000 + #define E5_STALLCURRENT 1500 + #define E5_MAX_VOLTAGE 127 + #define E5_CHAIN_POS 0 + #endif + + /** + * Monitor L6470 drivers for error conditions like over temperature and over current. + * In the case of over temperature Marlin can decrease the drive until the error condition clears. + * Other detected conditions can be used to stop the current print. + * Relevant g-codes: + * M906 - I1/2/3/4/5 Set or get motor drive level using axis codes X, Y, Z, E. Report values if no axis codes given. + * I not present or I0 or I1 - X, Y, Z or E0 + * I2 - X2, Y2, Z2 or E1 + * I3 - Z3 or E3 + * I4 - E4 + * I5 - E5 + * M916 - Increase drive level until get thermal warning + * M917 - Find minimum current thresholds + * M918 - Increase speed until max or error + * M122 S0/1 - Report driver parameters + */ + //#define MONITOR_L6470_DRIVER_STATUS + + #if ENABLED(MONITOR_L6470_DRIVER_STATUS) + #define KVAL_HOLD_STEP_DOWN 1 + //#define L6470_STOP_ON_ERROR + #endif + +#endif // L6470 + +/** + * TWI/I2C BUS + * + * This feature is an EXPERIMENTAL feature so it shall not be used on production + * machines. Enabling this will allow you to send and receive I2C data from slave + * devices on the bus. + * + * ; Example #1 + * ; This macro send the string "Marlin" to the slave device with address 0x63 (99) + * ; It uses multiple M260 commands with one B arg + * M260 A99 ; Target slave address + * M260 B77 ; M + * M260 B97 ; a + * M260 B114 ; r + * M260 B108 ; l + * M260 B105 ; i + * M260 B110 ; n + * M260 S1 ; Send the current buffer + * + * ; Example #2 + * ; Request 6 bytes from slave device with address 0x63 (99) + * M261 A99 B5 + * + * ; Example #3 + * ; Example serial output of a M261 request + * echo:i2c-reply: from:99 bytes:5 data:hello + */ + +// @section i2cbus + +//#define EXPERIMENTAL_I2CBUS +#define I2C_SLAVE_ADDRESS 0 // Set a value from 8 to 127 to act as a slave + +// @section extras + +/** + * Photo G-code + * Add the M240 G-code to take a photo. + * The photo can be triggered by a digital pin or a physical movement. + */ +//#define PHOTO_GCODE +#if ENABLED(PHOTO_GCODE) + // A position to move to (and raise Z) before taking the photo + //#define PHOTO_POSITION { X_MAX_POS - 5, Y_MAX_POS, 0 } // { xpos, ypos, zraise } (M240 X Y Z) + //#define PHOTO_DELAY_MS 100 // (ms) Duration to pause before moving back (M240 P) + //#define PHOTO_RETRACT_MM 6.5 // (mm) E retract/recover for the photo move (M240 R S) + + // Canon RC-1 or homebrew digital camera trigger + // Data from: http://www.doc-diy.net/photo/rc-1_hacked/ + //#define PHOTOGRAPH_PIN 23 + + // Canon Hack Development Kit + // http://captain-slow.dk/2014/03/09/3d-printing-timelapses/ + //#define CHDK_PIN 4 + + // Optional second move with delay to trigger the camera shutter + //#define PHOTO_SWITCH_POSITION { X_MAX_POS, Y_MAX_POS } // { xpos, ypos } (M240 I J) + + // Duration to hold the switch or keep CHDK_PIN high + //#define PHOTO_SWITCH_MS 50 // (ms) (M240 D) +#endif + +/** + * Spindle & Laser control + * + * Add the M3, M4, and M5 commands to turn the spindle/laser on and off, and + * to set spindle speed, spindle direction, and laser power. + * + * SuperPid is a router/spindle speed controller used in the CNC milling community. + * Marlin can be used to turn the spindle on and off. It can also be used to set + * the spindle speed from 5,000 to 30,000 RPM. + * + * You'll need to select a pin for the ON/OFF function and optionally choose a 0-5V + * hardware PWM pin for the speed control and a pin for the rotation direction. + * + * See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details. + */ +//#define SPINDLE_FEATURE +//#define LASER_FEATURE +#if EITHER(SPINDLE_FEATURE, LASER_FEATURE) + #define SPINDLE_LASER_ACTIVE_HIGH false // Set to "true" if the on/off function is active HIGH + #define SPINDLE_LASER_PWM true // Set to "true" if your controller supports setting the speed/power + #define SPINDLE_LASER_PWM_INVERT true // Set to "true" if the speed/power goes up when you want it to go slower + #define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power + #define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop + + #if ENABLED(SPINDLE_FEATURE) + //#define SPINDLE_CHANGE_DIR // Enable if your spindle controller can change spindle direction + #define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction + #define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed + + /** + * The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power + * + * SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT + * where PWM duty cycle varies from 0 to 255 + * + * set the following for your controller (ALL MUST BE SET) + */ + #define SPEED_POWER_SLOPE 118.4 + #define SPEED_POWER_INTERCEPT 0 + #define SPEED_POWER_MIN 5000 + #define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM + #else + #define SPEED_POWER_SLOPE 0.3922 + #define SPEED_POWER_INTERCEPT 0 + #define SPEED_POWER_MIN 10 + #define SPEED_POWER_MAX 100 // 0-100% + #endif +#endif + +/** + * Coolant Control + * + * Add the M7, M8, and M9 commands to turn mist or flood coolant on and off. + * + * Note: COOLANT_MIST_PIN and/or COOLANT_FLOOD_PIN must also be defined. + */ +//#define COOLANT_CONTROL +#if ENABLED(COOLANT_CONTROL) + #define COOLANT_MIST // Enable if mist coolant is present + #define COOLANT_FLOOD // Enable if flood coolant is present + #define COOLANT_MIST_INVERT false // Set "true" if the on/off function is reversed + #define COOLANT_FLOOD_INVERT false // Set "true" if the on/off function is reversed +#endif + +/** + * Filament Width Sensor + * + * Measures the filament width in real-time and adjusts + * flow rate to compensate for any irregularities. + * + * Also allows the measured filament diameter to set the + * extrusion rate, so the slicer only has to specify the + * volume. + * + * Only a single extruder is supported at this time. + * + * 34 RAMPS_14 : Analog input 5 on the AUX2 connector + * 81 PRINTRBOARD : Analog input 2 on the Exp1 connector (version B,C,D,E) + * 301 RAMBO : Analog input 3 + * + * Note: May require analog pins to be defined for other boards. + */ +//#define FILAMENT_WIDTH_SENSOR + +#if ENABLED(FILAMENT_WIDTH_SENSOR) + #define FILAMENT_SENSOR_EXTRUDER_NUM 0 // Index of the extruder that has the filament sensor. :[0,1,2,3,4] + #define MEASUREMENT_DELAY_CM 14 // (cm) The distance from the filament sensor to the melting chamber + + #define FILWIDTH_ERROR_MARGIN 1.0 // (mm) If a measurement differs too much from nominal width ignore it + #define MAX_MEASUREMENT_DELAY 20 // (bytes) Buffer size for stored measurements (1 byte per cm). Must be larger than MEASUREMENT_DELAY_CM. + + #define DEFAULT_MEASURED_FILAMENT_DIA DEFAULT_NOMINAL_FILAMENT_DIA // Set measured to nominal initially + + // Display filament width on the LCD status line. Status messages will expire after 5 seconds. + //#define FILAMENT_LCD_DISPLAY +#endif + +/** + * CNC Coordinate Systems + * + * Enables G53 and G54-G59.3 commands to select coordinate systems + * and G92.1 to reset the workspace to native machine space. + */ +//#define CNC_COORDINATE_SYSTEMS + +/** + * Auto-report temperatures with M155 S + */ +#define AUTO_REPORT_TEMPERATURES + +/** + * Include capabilities in M115 output + */ +#define EXTENDED_CAPABILITIES_REPORT + +/** + * Disable all Volumetric extrusion options + */ +//#define NO_VOLUMETRICS + +#if DISABLED(NO_VOLUMETRICS) + /** + * Volumetric extrusion default state + * Activate to make volumetric extrusion the default method, + * with DEFAULT_NOMINAL_FILAMENT_DIA as the default diameter. + * + * M200 D0 to disable, M200 Dn to set a new diameter. + */ + //#define VOLUMETRIC_DEFAULT_ON +#endif + +/** + * Enable this option for a leaner build of Marlin that removes all + * workspace offsets, simplifying coordinate transformations, leveling, etc. + * + * - M206 and M428 are disabled. + * - G92 will revert to its behavior from Marlin 1.0. + */ +//#define NO_WORKSPACE_OFFSETS + +/** + * Set the number of proportional font spaces required to fill up a typical character space. + * This can help to better align the output of commands like `G29 O` Mesh Output. + * + * For clients that use a fixed-width font (like OctoPrint), leave this set to 1.0. + * Otherwise, adjust according to your client and font. + */ +#define PROPORTIONAL_FONT_RATIO 1.0 + +/** + * Spend 28 bytes of SRAM to optimize the GCode parser + */ +#define FASTER_GCODE_PARSER + +/** + * CNC G-code options + * Support CNC-style G-code dialects used by laser cutters, drawing machine cams, etc. + * Note that G0 feedrates should be used with care for 3D printing (if used at all). + * High feedrates may cause ringing and harm print quality. + */ +//#define PAREN_COMMENTS // Support for parentheses-delimited comments +//#define GCODE_MOTION_MODES // Remember the motion mode (G0 G1 G2 G3 G5 G38.X) and apply for X Y Z E F, etc. + +// Enable and set a (default) feedrate for all G0 moves +//#define G0_FEEDRATE 3000 // (mm/m) +#ifdef G0_FEEDRATE + //#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode +#endif + +/** + * G-code Macros + * + * Add G-codes M810-M819 to define and run G-code macros. + * Macros are not saved to EEPROM. + */ +//#define GCODE_MACROS +#if ENABLED(GCODE_MACROS) + #define GCODE_MACROS_SLOTS 5 // Up to 10 may be used + #define GCODE_MACROS_SLOT_SIZE 50 // Maximum length of a single macro +#endif + +/** + * User-defined menu items that execute custom GCode + */ +//#define CUSTOM_USER_MENUS +#if ENABLED(CUSTOM_USER_MENUS) + //#define CUSTOM_USER_MENU_TITLE "Custom Commands" + #define USER_SCRIPT_DONE "M117 User Script Done" + #define USER_SCRIPT_AUDIBLE_FEEDBACK + //#define USER_SCRIPT_RETURN // Return to status screen after a script + + #define USER_DESC_1 "Home & UBL Info" + #define USER_GCODE_1 "G28\nG29 W" + + #define USER_DESC_2 "Preheat for " PREHEAT_1_LABEL + #define USER_GCODE_2 "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND) + + #define USER_DESC_3 "Preheat for " PREHEAT_2_LABEL + #define USER_GCODE_3 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND) + + #define USER_DESC_4 "Heat Bed/Home/Level" + #define USER_GCODE_4 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29" + + #define USER_DESC_5 "Home & Info" + #define USER_GCODE_5 "G28\nM503" +#endif + +/** + * Host Action Commands + * + * Define host streamer action commands in compliance with the standard. + * + * See https://reprap.org/wiki/G-code#Action_commands + * Common commands ........ poweroff, pause, paused, resume, resumed, cancel + * G29_RETRY_AND_RECOVER .. probe_rewipe, probe_failed + * + * Some features add reason codes to extend these commands. + * + * Host Prompt Support enables Marlin to use the host for user prompts so + * filament runout and other processes can be managed from the host side. + */ +//#define HOST_ACTION_COMMANDS +#if ENABLED(HOST_ACTION_COMMANDS) + //#define HOST_PROMPT_SUPPORT +#endif + +//=========================================================================== +//====================== I2C Position Encoder Settings ====================== +//=========================================================================== + +/** + * I2C position encoders for closed loop control. + * Developed by Chris Barr at Aus3D. + * + * Wiki: http://wiki.aus3d.com.au/Magnetic_Encoder + * Github: https://github.com/Aus3D/MagneticEncoder + * + * Supplier: http://aus3d.com.au/magnetic-encoder-module + * Alternative Supplier: http://reliabuild3d.com/ + * + * Reliabuild encoders have been modified to improve reliability. + */ + +//#define I2C_POSITION_ENCODERS +#if ENABLED(I2C_POSITION_ENCODERS) + + #define I2CPE_ENCODER_CNT 1 // The number of encoders installed; max of 5 + // encoders supported currently. + + #define I2CPE_ENC_1_ADDR I2CPE_PRESET_ADDR_X // I2C address of the encoder. 30-200. + #define I2CPE_ENC_1_AXIS X_AXIS // Axis the encoder module is installed on. _AXIS. + #define I2CPE_ENC_1_TYPE I2CPE_ENC_TYPE_LINEAR // Type of encoder: I2CPE_ENC_TYPE_LINEAR -or- + // I2CPE_ENC_TYPE_ROTARY. + #define I2CPE_ENC_1_TICKS_UNIT 2048 // 1024 for magnetic strips with 2mm poles; 2048 for + // 1mm poles. For linear encoders this is ticks / mm, + // for rotary encoders this is ticks / revolution. + //#define I2CPE_ENC_1_TICKS_REV (16 * 200) // Only needed for rotary encoders; number of stepper + // steps per full revolution (motor steps/rev * microstepping) + //#define I2CPE_ENC_1_INVERT // Invert the direction of axis travel. + #define I2CPE_ENC_1_EC_METHOD I2CPE_ECM_MICROSTEP // Type of error error correction. + #define I2CPE_ENC_1_EC_THRESH 0.10 // Threshold size for error (in mm) above which the + // printer will attempt to correct the error; errors + // smaller than this are ignored to minimize effects of + // measurement noise / latency (filter). + + #define I2CPE_ENC_2_ADDR I2CPE_PRESET_ADDR_Y // Same as above, but for encoder 2. + #define I2CPE_ENC_2_AXIS Y_AXIS + #define I2CPE_ENC_2_TYPE I2CPE_ENC_TYPE_LINEAR + #define I2CPE_ENC_2_TICKS_UNIT 2048 + //#define I2CPE_ENC_2_TICKS_REV (16 * 200) + //#define I2CPE_ENC_2_INVERT + #define I2CPE_ENC_2_EC_METHOD I2CPE_ECM_MICROSTEP + #define I2CPE_ENC_2_EC_THRESH 0.10 + + #define I2CPE_ENC_3_ADDR I2CPE_PRESET_ADDR_Z // Encoder 3. Add additional configuration options + #define I2CPE_ENC_3_AXIS Z_AXIS // as above, or use defaults below. + + #define I2CPE_ENC_4_ADDR I2CPE_PRESET_ADDR_E // Encoder 4. + #define I2CPE_ENC_4_AXIS E_AXIS + + #define I2CPE_ENC_5_ADDR 34 // Encoder 5. + #define I2CPE_ENC_5_AXIS E_AXIS + + // Default settings for encoders which are enabled, but without settings configured above. + #define I2CPE_DEF_TYPE I2CPE_ENC_TYPE_LINEAR + #define I2CPE_DEF_ENC_TICKS_UNIT 2048 + #define I2CPE_DEF_TICKS_REV (16 * 200) + #define I2CPE_DEF_EC_METHOD I2CPE_ECM_NONE + #define I2CPE_DEF_EC_THRESH 0.1 + + //#define I2CPE_ERR_THRESH_ABORT 100.0 // Threshold size for error (in mm) error on any given + // axis after which the printer will abort. Comment out to + // disable abort behavior. + + #define I2CPE_TIME_TRUSTED 10000 // After an encoder fault, there must be no further fault + // for this amount of time (in ms) before the encoder + // is trusted again. + + /** + * Position is checked every time a new command is executed from the buffer but during long moves, + * this setting determines the minimum update time between checks. A value of 100 works well with + * error rolling average when attempting to correct only for skips and not for vibration. + */ + #define I2CPE_MIN_UPD_TIME_MS 4 // (ms) Minimum time between encoder checks. + + // Use a rolling average to identify persistant errors that indicate skips, as opposed to vibration and noise. + #define I2CPE_ERR_ROLLING_AVERAGE + +#endif // I2C_POSITION_ENCODERS + +/** + * MAX7219 Debug Matrix + * + * Add support for a low-cost 8x8 LED Matrix based on the Max7219 chip as a realtime status display. + * Requires 3 signal wires. Some useful debug options are included to demonstrate its usage. + */ +//#define MAX7219_DEBUG +#if ENABLED(MAX7219_DEBUG) + #define MAX7219_CLK_PIN 64 + #define MAX7219_DIN_PIN 57 + #define MAX7219_LOAD_PIN 44 + + //#define MAX7219_GCODE // Add the M7219 G-code to control the LED matrix + #define MAX7219_INIT_TEST 2 // Do a test pattern at initialization (Set to 2 for spiral) + #define MAX7219_NUMBER_UNITS 1 // Number of Max7219 units in chain. + #define MAX7219_ROTATE 0 // Rotate the display clockwise (in multiples of +/- 90°) + // connector at: right=0 bottom=-90 top=90 left=180 + //#define MAX7219_REVERSE_ORDER // The individual LED matrix units may be in reversed order + //#define MAX7219_SIDE_BY_SIDE // Big chip+matrix boards can be chained side-by-side + + /** + * Sample debug features + * If you add more debug displays, be careful to avoid conflicts! + */ + #define MAX7219_DEBUG_PRINTER_ALIVE // Blink corner LED of 8x8 matrix to show that the firmware is functioning + #define MAX7219_DEBUG_PLANNER_HEAD 3 // Show the planner queue head position on this and the next LED matrix row + #define MAX7219_DEBUG_PLANNER_TAIL 5 // Show the planner queue tail position on this and the next LED matrix row + + #define MAX7219_DEBUG_PLANNER_QUEUE 0 // Show the current planner queue depth on this and the next LED matrix row + // If you experience stuttering, reboots, etc. this option can reveal how + // tweaks made to the configuration are affecting the printer in real-time. +#endif + +/** + * NanoDLP Sync support + * + * Add support for Synchronized Z moves when using with NanoDLP. G0/G1 axis moves will output "Z_move_comp" + * string to enable synchronization with DLP projector exposure. This change will allow to use + * [[WaitForDoneMessage]] instead of populating your gcode with M400 commands + */ +//#define NANODLP_Z_SYNC +#if ENABLED(NANODLP_Z_SYNC) + //#define NANODLP_ALL_AXIS // Enables "Z_move_comp" output on any axis move. + // Default behavior is limited to Z axis only. +#endif + +/** + * WiFi Support (Espressif ESP32 WiFi) + */ +//#define WIFISUPPORT +#if ENABLED(WIFISUPPORT) + #define WIFI_SSID "Wifi SSID" + #define WIFI_PWD "Wifi Password" + //#define WEBSUPPORT // Start a webserver with auto-discovery + //#define OTASUPPORT // Support over-the-air firmware updates +#endif + +/** + * Prusa Multi-Material Unit v2 + * Enable in Configuration.h + */ +#if ENABLED(PRUSA_MMU2) + + // Serial port used for communication with MMU2. + // For AVR enable the UART port used for the MMU. (e.g., internalSerial) + // For 32-bit boards check your HAL for available serial ports. (e.g., Serial2) + #define INTERNAL_SERIAL_PORT 2 + #define MMU2_SERIAL internalSerial + + // Use hardware reset for MMU if a pin is defined for it + //#define MMU2_RST_PIN 23 + + // Enable if the MMU2 has 12V stepper motors (MMU2 Firmware 1.0.2 and up) + //#define MMU2_MODE_12V + + // G-code to execute when MMU2 F.I.N.D.A. probe detects filament runout + #define MMU2_FILAMENT_RUNOUT_SCRIPT "M600" + + // Add an LCD menu for MMU2 + //#define MMU2_MENUS + #if ENABLED(MMU2_MENUS) + // Settings for filament load / unload from the LCD menu. + // This is for Prusa MK3-style extruders. Customize for your hardware. + #define MMU2_FILAMENTCHANGE_EJECT_FEED 80.0 + #define MMU2_LOAD_TO_NOZZLE_SEQUENCE \ + { 7.2, 562 }, \ + { 14.4, 871 }, \ + { 36.0, 1393 }, \ + { 14.4, 871 }, \ + { 50.0, 198 } + + #define MMU2_RAMMING_SEQUENCE \ + { 1.0, 1000 }, \ + { 1.0, 1500 }, \ + { 2.0, 2000 }, \ + { 1.5, 3000 }, \ + { 2.5, 4000 }, \ + { -15.0, 5000 }, \ + { -14.0, 1200 }, \ + { -6.0, 600 }, \ + { 10.0, 700 }, \ + { -10.0, 400 }, \ + { -50.0, 2000 } + + #endif + + //#define MMU2_DEBUG // Write debug info to serial output + +#endif // PRUSA_MMU2 + +/** + * Advanced Print Counter settings + */ +#if ENABLED(PRINTCOUNTER) + #define SERVICE_WARNING_BUZZES 3 + // Activate up to 3 service interval watchdogs + #define SERVICE_NAME_1 "Lubricate axis" + #define SERVICE_INTERVAL_1 100 // print hours + #define SERVICE_NAME_2 "Change X an Y belt" + #define SERVICE_INTERVAL_2 300 // print hours + #define SERVICE_NAME_3 "Change Z belt" + #define SERVICE_INTERVAL_3 1000 // print hours +#endif + +// @section develop + +/** + * M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins + */ +#define PINS_DEBUGGING + +// Enable Marlin dev mode which adds some special commands +//#define MARLIN_DEV_MODE diff --git a/config/examples/Infitary/i3-M508/Configuration.h b/config/examples/Infitary/i3-M508/Configuration.h index 237f8ba00c..ac7242120b 100644 --- a/config/examples/Infitary/i3-M508/Configuration.h +++ b/config/examples/Infitary/i3-M508/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2041,7 +2042,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Infitary/i3-M508/Configuration_adv.h b/config/examples/Infitary/i3-M508/Configuration_adv.h index dd104129e8..225e8caded 100644 --- a/config/examples/Infitary/i3-M508/Configuration_adv.h +++ b/config/examples/Infitary/i3-M508/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/JGAurora/A1/Configuration.h b/config/examples/JGAurora/A1/Configuration.h index 33ae0ef427..16577c8bc1 100644 --- a/config/examples/JGAurora/A1/Configuration.h +++ b/config/examples/JGAurora/A1/Configuration.h @@ -364,6 +364,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -407,7 +408,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2045,7 +2046,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/JGAurora/A1/Configuration_adv.h b/config/examples/JGAurora/A1/Configuration_adv.h index 7e1718c86d..5eaf018e3a 100644 --- a/config/examples/JGAurora/A1/Configuration_adv.h +++ b/config/examples/JGAurora/A1/Configuration_adv.h @@ -663,10 +663,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -856,11 +856,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -885,23 +906,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -936,6 +940,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/JGAurora/A5/Configuration.h b/config/examples/JGAurora/A5/Configuration.h index 857ced38b8..c6a91a0560 100644 --- a/config/examples/JGAurora/A5/Configuration.h +++ b/config/examples/JGAurora/A5/Configuration.h @@ -364,6 +364,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -407,7 +408,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 15 // manual calibration of thermistor in JGAurora A5 hotend #define TEMP_SENSOR_1 0 @@ -2049,7 +2050,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/JGAurora/A5/Configuration_adv.h b/config/examples/JGAurora/A5/Configuration_adv.h index 841e98e664..581849514f 100644 --- a/config/examples/JGAurora/A5/Configuration_adv.h +++ b/config/examples/JGAurora/A5/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/JGAurora/A5S/Configuration.h b/config/examples/JGAurora/A5S/Configuration.h index 27e9be8f35..23d8d4749f 100644 --- a/config/examples/JGAurora/A5S/Configuration.h +++ b/config/examples/JGAurora/A5S/Configuration.h @@ -364,6 +364,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -407,7 +408,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2045,7 +2046,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/JGAurora/A5S/Configuration_adv.h b/config/examples/JGAurora/A5S/Configuration_adv.h index 7e1718c86d..5eaf018e3a 100644 --- a/config/examples/JGAurora/A5S/Configuration_adv.h +++ b/config/examples/JGAurora/A5S/Configuration_adv.h @@ -663,10 +663,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -856,11 +856,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -885,23 +906,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -936,6 +940,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/MakerParts/Configuration.h b/config/examples/MakerParts/Configuration.h index ffdbdcd815..e9fef18718 100644 --- a/config/examples/MakerParts/Configuration.h +++ b/config/examples/MakerParts/Configuration.h @@ -379,6 +379,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -422,7 +423,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2057,7 +2058,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/MakerParts/Configuration_adv.h b/config/examples/MakerParts/Configuration_adv.h index fe20a76f5e..5e96f58c40 100644 --- a/config/examples/MakerParts/Configuration_adv.h +++ b/config/examples/MakerParts/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + #define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Malyan/M150/Configuration.h b/config/examples/Malyan/M150/Configuration.h index 6be371d1b6..c537d13bd8 100644 --- a/config/examples/Malyan/M150/Configuration.h +++ b/config/examples/Malyan/M150/Configuration.h @@ -364,6 +364,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -407,7 +408,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2065,7 +2066,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Malyan/M150/Configuration_adv.h b/config/examples/Malyan/M150/Configuration_adv.h index 591e398852..d9d81846af 100644 --- a/config/examples/Malyan/M150/Configuration_adv.h +++ b/config/examples/Malyan/M150/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Malyan/M200/Configuration.h b/config/examples/Malyan/M200/Configuration.h index 87c368906e..4fb2a36916 100644 --- a/config/examples/Malyan/M200/Configuration.h +++ b/config/examples/Malyan/M200/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 11 #define TEMP_SENSOR_1 0 @@ -2036,7 +2037,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Malyan/M200/Configuration_adv.h b/config/examples/Malyan/M200/Configuration_adv.h index f39f078f28..f5c0fd47ed 100644 --- a/config/examples/Malyan/M200/Configuration_adv.h +++ b/config/examples/Malyan/M200/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Micromake/C1/basic/Configuration.h b/config/examples/Micromake/C1/basic/Configuration.h index 4d145bb028..7b8b886fcd 100644 --- a/config/examples/Micromake/C1/basic/Configuration.h +++ b/config/examples/Micromake/C1/basic/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2041,7 +2042,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Micromake/C1/enhanced/Configuration.h b/config/examples/Micromake/C1/enhanced/Configuration.h index 39335a990a..02178a99d0 100644 --- a/config/examples/Micromake/C1/enhanced/Configuration.h +++ b/config/examples/Micromake/C1/enhanced/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2041,7 +2042,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Micromake/C1/enhanced/Configuration_adv.h b/config/examples/Micromake/C1/enhanced/Configuration_adv.h index 115070f8b9..6cb6eee15c 100644 --- a/config/examples/Micromake/C1/enhanced/Configuration_adv.h +++ b/config/examples/Micromake/C1/enhanced/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Mks/Robin/Configuration.h b/config/examples/Mks/Robin/Configuration.h index 343cbfb201..2338741646 100644 --- a/config/examples/Mks/Robin/Configuration.h +++ b/config/examples/Mks/Robin/Configuration.h @@ -360,6 +360,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -403,7 +404,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 1 @@ -2039,7 +2040,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Mks/Robin/Configuration_adv.h b/config/examples/Mks/Robin/Configuration_adv.h index ca837e19b9..e6ad372b3c 100644 --- a/config/examples/Mks/Robin/Configuration_adv.h +++ b/config/examples/Mks/Robin/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Mks/Sbase/Configuration.h b/config/examples/Mks/Sbase/Configuration.h index 9583422333..dd5e3a92af 100644 --- a/config/examples/Mks/Sbase/Configuration.h +++ b/config/examples/Mks/Sbase/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -2037,7 +2038,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Mks/Sbase/Configuration_adv.h b/config/examples/Mks/Sbase/Configuration_adv.h index 7824073f4a..1015a220a0 100644 --- a/config/examples/Mks/Sbase/Configuration_adv.h +++ b/config/examples/Mks/Sbase/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -852,11 +852,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -881,23 +902,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -932,6 +936,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Printrbot/PrintrboardG2/Configuration.h b/config/examples/Printrbot/PrintrboardG2/Configuration.h index f06a8b254c..f9951a0dfd 100644 --- a/config/examples/Printrbot/PrintrboardG2/Configuration.h +++ b/config/examples/Printrbot/PrintrboardG2/Configuration.h @@ -360,6 +360,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -403,7 +404,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2045,7 +2046,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/RapideLite/RL200/Configuration.h b/config/examples/RapideLite/RL200/Configuration.h index 1fee434f57..6a8fa23db6 100644 --- a/config/examples/RapideLite/RL200/Configuration.h +++ b/config/examples/RapideLite/RL200/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2037,7 +2038,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/RapideLite/RL200/Configuration_adv.h b/config/examples/RapideLite/RL200/Configuration_adv.h index 160c341991..55dd2b7c2d 100644 --- a/config/examples/RapideLite/RL200/Configuration_adv.h +++ b/config/examples/RapideLite/RL200/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/RepRapPro/Huxley/Configuration.h b/config/examples/RepRapPro/Huxley/Configuration.h index c0503a8678..4b091a358e 100644 --- a/config/examples/RepRapPro/Huxley/Configuration.h +++ b/config/examples/RepRapPro/Huxley/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2086,7 +2087,7 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/RepRapWorld/Megatronics/Configuration.h b/config/examples/RepRapWorld/Megatronics/Configuration.h index 86c23d6c57..0900fa81ad 100644 --- a/config/examples/RepRapWorld/Megatronics/Configuration.h +++ b/config/examples/RepRapWorld/Megatronics/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2037,7 +2038,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/RigidBot/Configuration.h b/config/examples/RigidBot/Configuration.h index 923f387943..7973879348 100644 --- a/config/examples/RigidBot/Configuration.h +++ b/config/examples/RigidBot/Configuration.h @@ -362,6 +362,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -405,7 +406,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 // DGlass3D = 5; RigidBot = 1; 3DSv6 = 5 #define TEMP_SENSOR_1 0 @@ -2037,7 +2038,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/RigidBot/Configuration_adv.h b/config/examples/RigidBot/Configuration_adv.h index a7528d0ddb..53d5a30563 100644 --- a/config/examples/RigidBot/Configuration_adv.h +++ b/config/examples/RigidBot/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/SCARA/Configuration.h b/config/examples/SCARA/Configuration.h index 61e2fb6805..a7a02c0f8f 100644 --- a/config/examples/SCARA/Configuration.h +++ b/config/examples/SCARA/Configuration.h @@ -386,6 +386,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -429,7 +430,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2046,7 +2047,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/SCARA/Configuration_adv.h b/config/examples/SCARA/Configuration_adv.h index f0e34e684d..8b8c5739b6 100644 --- a/config/examples/SCARA/Configuration_adv.h +++ b/config/examples/SCARA/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full //#define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration.h b/config/examples/STM32/Black_STM32F407VET6/Configuration.h index 7b95013b3c..0903dae3f0 100644 --- a/config/examples/STM32/Black_STM32F407VET6/Configuration.h +++ b/config/examples/STM32/Black_STM32F407VET6/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 1 @@ -2037,7 +2038,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h index cbd9dd6344..1975d27400 100644 --- a/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h +++ b/config/examples/STM32/Black_STM32F407VET6/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/STM32/STM32F10/Configuration.h b/config/examples/STM32/STM32F10/Configuration.h index 6474792c55..8827cc5421 100644 --- a/config/examples/STM32/STM32F10/Configuration.h +++ b/config/examples/STM32/STM32F10/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #warning temp_sensor set to 998/999 (fake) #define TEMP_SENSOR_0 999 @@ -2039,7 +2040,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/STM32/STM32F4/Configuration.h b/config/examples/STM32/STM32F4/Configuration.h index a693e550c3..dfa52035ce 100644 --- a/config/examples/STM32/STM32F4/Configuration.h +++ b/config/examples/STM32/STM32F4/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2037,7 +2038,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/STM32/stm32f103ret6/Configuration.h b/config/examples/STM32/stm32f103ret6/Configuration.h index 16a5a74449..abda3c7f1e 100644 --- a/config/examples/STM32/stm32f103ret6/Configuration.h +++ b/config/examples/STM32/stm32f103ret6/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #warning temp_sensor set to 998/999 (fake) #define TEMP_SENSOR_0 999 @@ -2039,7 +2040,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Sanguinololu/Configuration.h b/config/examples/Sanguinololu/Configuration.h index baff32d42b..2782705eea 100644 --- a/config/examples/Sanguinololu/Configuration.h +++ b/config/examples/Sanguinololu/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2068,7 +2069,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Sanguinololu/Configuration_adv.h b/config/examples/Sanguinololu/Configuration_adv.h index 06b7d88d00..2c63cff33e 100644 --- a/config/examples/Sanguinololu/Configuration_adv.h +++ b/config/examples/Sanguinololu/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Tevo/Michelangelo/Configuration.h b/config/examples/Tevo/Michelangelo/Configuration.h index f77da5f1d3..f41e67e959 100644 --- a/config/examples/Tevo/Michelangelo/Configuration.h +++ b/config/examples/Tevo/Michelangelo/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2042,7 +2043,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Tevo/Michelangelo/Configuration_adv.h b/config/examples/Tevo/Michelangelo/Configuration_adv.h index ed7aefa735..1d97c887df 100644 --- a/config/examples/Tevo/Michelangelo/Configuration_adv.h +++ b/config/examples/Tevo/Michelangelo/Configuration_adv.h @@ -657,10 +657,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -850,11 +850,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + #define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -879,23 +900,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -930,6 +934,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Tevo/Tarantula Pro/Configuration.h b/config/examples/Tevo/Tarantula Pro/Configuration.h index 2974afd685..9c8b56ba04 100644 --- a/config/examples/Tevo/Tarantula Pro/Configuration.h +++ b/config/examples/Tevo/Tarantula Pro/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2035,7 +2036,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Tevo/Tarantula Pro/Configuration_adv.h b/config/examples/Tevo/Tarantula Pro/Configuration_adv.h index 2cf19521a6..c9648ea197 100644 --- a/config/examples/Tevo/Tarantula Pro/Configuration_adv.h +++ b/config/examples/Tevo/Tarantula Pro/Configuration_adv.h @@ -654,10 +654,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -847,11 +847,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + #define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -876,23 +897,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -927,6 +931,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h index 7c2cd20c7a..c6f0ac9dfe 100644 --- a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h +++ b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2042,7 +2043,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h index 9ecb3377ab..99a4cc0f97 100644 --- a/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h +++ b/config/examples/Tevo/Tornado/V1 (MKS Base)/Configuration_adv.h @@ -657,10 +657,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -850,11 +850,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + #define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -879,23 +900,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -930,6 +934,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h index b981ee8afd..7b3400c760 100644 --- a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h +++ b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2042,7 +2043,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h index 9ecb3377ab..99a4cc0f97 100644 --- a/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h +++ b/config/examples/Tevo/Tornado/V2 (MKS GEN-L)/Configuration_adv.h @@ -657,10 +657,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -850,11 +850,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + #define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -879,23 +900,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -930,6 +934,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/TheBorg/Configuration.h b/config/examples/TheBorg/Configuration.h index 010ea9a1f8..64a6401dcc 100644 --- a/config/examples/TheBorg/Configuration.h +++ b/config/examples/TheBorg/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -2037,7 +2038,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/TheBorg/Configuration_adv.h b/config/examples/TheBorg/Configuration_adv.h index 0dd90aa0e7..3b9927d581 100644 --- a/config/examples/TheBorg/Configuration_adv.h +++ b/config/examples/TheBorg/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/TinyBoy2/Configuration.h b/config/examples/TinyBoy2/Configuration.h index 59abc9449b..8760e16c61 100644 --- a/config/examples/TinyBoy2/Configuration.h +++ b/config/examples/TinyBoy2/Configuration.h @@ -381,6 +381,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -424,7 +425,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -2093,7 +2094,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/TinyBoy2/Configuration_adv.h b/config/examples/TinyBoy2/Configuration_adv.h index f6efaadc09..ba50def85f 100644 --- a/config/examples/TinyBoy2/Configuration_adv.h +++ b/config/examples/TinyBoy2/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + #define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Tronxy/X1/Configuration.h b/config/examples/Tronxy/X1/Configuration.h index f98aae5863..be6edb0325 100644 --- a/config/examples/Tronxy/X1/Configuration.h +++ b/config/examples/Tronxy/X1/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 11 #define TEMP_SENSOR_1 0 @@ -2037,7 +2038,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Tronxy/X3A/Configuration.h b/config/examples/Tronxy/X3A/Configuration.h index 6152a4e903..3237a3727f 100644 --- a/config/examples/Tronxy/X3A/Configuration.h +++ b/config/examples/Tronxy/X3A/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 6 #define TEMP_SENSOR_1 0 @@ -2041,7 +2042,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Tronxy/X3A/Configuration_adv.h b/config/examples/Tronxy/X3A/Configuration_adv.h index 74fca2a16f..6a90dd450b 100644 --- a/config/examples/Tronxy/X3A/Configuration_adv.h +++ b/config/examples/Tronxy/X3A/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Tronxy/X5S-2E/Configuration.h b/config/examples/Tronxy/X5S-2E/Configuration.h index 8bd88215ef..e507b97545 100644 --- a/config/examples/Tronxy/X5S-2E/Configuration.h +++ b/config/examples/Tronxy/X5S-2E/Configuration.h @@ -361,6 +361,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -404,7 +405,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2058,7 +2059,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Tronxy/X5S-2E/Configuration_adv.h b/config/examples/Tronxy/X5S-2E/Configuration_adv.h index 3291eccc5d..a3c684c7bc 100644 --- a/config/examples/Tronxy/X5S-2E/Configuration_adv.h +++ b/config/examples/Tronxy/X5S-2E/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + #define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Tronxy/X5S/Configuration.h b/config/examples/Tronxy/X5S/Configuration.h index ad9e4d2a0d..dfb7f0ce2a 100644 --- a/config/examples/Tronxy/X5S/Configuration.h +++ b/config/examples/Tronxy/X5S/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2037,7 +2038,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Tronxy/XY100/Configuration.h b/config/examples/Tronxy/XY100/Configuration.h index 3baad0f980..6d2071e3bb 100644 --- a/config/examples/Tronxy/XY100/Configuration.h +++ b/config/examples/Tronxy/XY100/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2048,7 +2049,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/UltiMachine/Archim1/Configuration.h b/config/examples/UltiMachine/Archim1/Configuration.h index 23ab1ce032..34654579b6 100644 --- a/config/examples/UltiMachine/Archim1/Configuration.h +++ b/config/examples/UltiMachine/Archim1/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2037,7 +2038,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/UltiMachine/Archim1/Configuration_adv.h b/config/examples/UltiMachine/Archim1/Configuration_adv.h index be5c608d67..44cad6efab 100644 --- a/config/examples/UltiMachine/Archim1/Configuration_adv.h +++ b/config/examples/UltiMachine/Archim1/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/UltiMachine/Archim2/Configuration.h b/config/examples/UltiMachine/Archim2/Configuration.h index cb05e2d8bb..5e088041a6 100644 --- a/config/examples/UltiMachine/Archim2/Configuration.h +++ b/config/examples/UltiMachine/Archim2/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2037,7 +2038,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/UltiMachine/Archim2/Configuration_adv.h b/config/examples/UltiMachine/Archim2/Configuration_adv.h index e5f13cfbee..83645407dd 100644 --- a/config/examples/UltiMachine/Archim2/Configuration_adv.h +++ b/config/examples/UltiMachine/Archim2/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/VORONDesign/Configuration.h b/config/examples/VORONDesign/Configuration.h index 0e93640d60..9b379f5e83 100644 --- a/config/examples/VORONDesign/Configuration.h +++ b/config/examples/VORONDesign/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 5 @@ -2046,7 +2047,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/VORONDesign/Configuration_adv.h b/config/examples/VORONDesign/Configuration_adv.h index 2de839f653..08059a94bd 100644 --- a/config/examples/VORONDesign/Configuration_adv.h +++ b/config/examples/VORONDesign/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Velleman/K8200/Configuration.h b/config/examples/Velleman/K8200/Configuration.h index 20473efc3d..54adde7b6c 100644 --- a/config/examples/Velleman/K8200/Configuration.h +++ b/config/examples/Velleman/K8200/Configuration.h @@ -379,6 +379,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -422,7 +423,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -2035,7 +2036,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Velleman/K8200/Configuration_adv.h b/config/examples/Velleman/K8200/Configuration_adv.h index ea06f7cf29..77c21db691 100644 --- a/config/examples/Velleman/K8200/Configuration_adv.h +++ b/config/examples/Velleman/K8200/Configuration_adv.h @@ -671,10 +671,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -864,11 +864,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -893,23 +914,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -944,6 +948,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Velleman/K8400/Configuration.h b/config/examples/Velleman/K8400/Configuration.h index f8e5616f50..f14fd6d374 100644 --- a/config/examples/Velleman/K8400/Configuration.h +++ b/config/examples/Velleman/K8400/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -2037,7 +2038,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Velleman/K8400/Configuration_adv.h b/config/examples/Velleman/K8400/Configuration_adv.h index 83524e2d33..0d54cda5cc 100644 --- a/config/examples/Velleman/K8400/Configuration_adv.h +++ b/config/examples/Velleman/K8400/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Velleman/K8400/Dual-head/Configuration.h b/config/examples/Velleman/K8400/Dual-head/Configuration.h index 375295124f..cb02c225bc 100644 --- a/config/examples/Velleman/K8400/Dual-head/Configuration.h +++ b/config/examples/Velleman/K8400/Dual-head/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 5 @@ -2037,7 +2038,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/WASP/PowerWASP/Configuration.h b/config/examples/WASP/PowerWASP/Configuration.h index f92e2df3c4..2cb98a24ac 100644 --- a/config/examples/WASP/PowerWASP/Configuration.h +++ b/config/examples/WASP/PowerWASP/Configuration.h @@ -378,6 +378,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -421,7 +422,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 -1 #define TEMP_SENSOR_1 0 @@ -2056,7 +2057,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/WASP/PowerWASP/Configuration_adv.h b/config/examples/WASP/PowerWASP/Configuration_adv.h index 1faa2ef346..e6e98d9a29 100644 --- a/config/examples/WASP/PowerWASP/Configuration_adv.h +++ b/config/examples/WASP/PowerWASP/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) #define POWER_LOSS_PIN 65 // Pin to detect power loss #define POWER_LOSS_STATE LOW // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Wanhao/Duplicator 6/Configuration.h b/config/examples/Wanhao/Duplicator 6/Configuration.h index a606dc4461..60533157f6 100644 --- a/config/examples/Wanhao/Duplicator 6/Configuration.h +++ b/config/examples/Wanhao/Duplicator 6/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 20 #define TEMP_SENSOR_1 0 @@ -2050,7 +2051,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h index c6b4844b67..c656b5b8d7 100644 --- a/config/examples/Wanhao/Duplicator 6/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator 6/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -853,11 +853,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + #define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -882,23 +903,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -933,6 +937,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h b/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h index 0cf5a39cbf..198b35814d 100644 --- a/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h +++ b/config/examples/Wanhao/Duplicator i3 Mini/Configuration.h @@ -90,7 +90,7 @@ */ // Enable to show the bitmap in Marlin/_Bootscreen.h on startup. -//#define SHOW_CUSTOM_BOOTSCREEN +#define SHOW_CUSTOM_BOOTSCREEN // Enable to show the bitmap in Marlin/_Statusscreen.h on the status screen. //#define CUSTOM_STATUS_SCREEN_IMAGE @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 13 #define TEMP_SENSOR_1 0 @@ -1895,7 +1896,7 @@ // MakerLab Mini Panel with graphic // controller and SD support - http://reprap.org/wiki/Mini_panel // -//#define MINIPANEL +#define MINIPANEL // // MaKr3d Makr-Panel with graphic controller and SD support. @@ -1936,7 +1937,7 @@ // MKS MINI12864 with graphic controller and SD support // https://reprap.org/wiki/MKS_MINI_12864 // -#define MKS_MINI_12864 +//#define MKS_MINI_12864 // // FYSETC variant of the MINI12864 graphic controller with SD support @@ -2037,7 +2038,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h b/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h index 72babee557..85917d8d80 100644 --- a/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h +++ b/config/examples/Wanhao/Duplicator i3 Mini/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + #define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/Wanhao/Duplicator i3 Mini/_Bootscreen.h b/config/examples/Wanhao/Duplicator i3 Mini/_Bootscreen.h new file mode 100644 index 0000000000..b647f46339 --- /dev/null +++ b/config/examples/Wanhao/Duplicator i3 Mini/_Bootscreen.h @@ -0,0 +1,53 @@ +/** + * Made with Marlin Bitmap Converter + * http://marlinfw.org/tools/u8glib/converter.html + */ +#define CUSTOM_BOOTSCREEN_BMPWIDTH 80 +#define CUSTOM_BOOTSCREEN_Y 3 + +const unsigned char custom_start_bmp[] PROGMEM = { + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000111,B11000000,B00000000,B00000000, + B00000000,B00000000,B00000000,B00000000,B00110111,B00000000,B01111111,B10111100,B00000000,B00000000, + B00000000,B00000000,B00000000,B00000000,B11111111,B11111111,B11111111,B10111111,B10000000,B00000000, + B00000000,B00000000,B00000000,B00000111,B11111111,B11111111,B11111111,B01111111,B11000000,B00000000, + B00000000,B00000000,B00000000,B00011111,B11101111,B11111111,B11111111,B01111111,B11111111,B00000000, + B00000000,B00000000,B00000000,B00111111,B11101111,B11111111,B11111111,B11111111,B11111111,B11100000, + B00000000,B00000000,B00000000,B11111111,B11101111,B11111111,B11111111,B11111111,B11100000,B00110000, + B00000000,B00000000,B00000011,B11111111,B11111111,B11111111,B11111111,B11111111,B11110000,B00000000, + B00000000,B00000000,B00000111,B11111111,B11111111,B11111111,B11111111,B11111111,B11110000,B00000000, + B00000000,B00000000,B00110111,B11111111,B11111111,B11111111,B11111111,B01111111,B11110000,B00000000, + B00000000,B00010111,B11110111,B11111111,B11101111,B11111111,B11111111,B01111111,B11110000,B00000000, + B00000000,B00011111,B11110111,B11111111,B11101111,B11111111,B11111111,B01111111,B11110000,B00000000, + B00000000,B00001111,B11110111,B11111111,B11111111,B11111111,B11111111,B10111111,B11111000,B00000000, + B00000000,B00001111,B11110111,B11111111,B11110111,B11111111,B11111111,B10111111,B11111000,B00000000, + B00000000,B00001111,B11111111,B11111111,B11110111,B11111111,B11111111,B10111111,B11111100,B00000000, + B00000000,B00001111,B11111011,B11111111,B11110111,B11111111,B11111111,B10111111,B11111100,B00000000, + B00000000,B00001111,B11111011,B11111111,B11111111,B11111111,B11111111,B11111111,B11111100,B00000000, + B00000000,B10001111,B11111101,B11111111,B11111011,B11111111,B11111111,B11011111,B11111000,B00000000, + B00000000,B11111111,B11111100,B11111111,B11111011,B11111111,B11111111,B10111111,B11110110,B00000000, + B00000100,B01111111,B11111110,B11111111,B11111011,B11111111,B11111111,B00011111,B11101111,B00000000, + B00000110,B01111111,B11111111,B00100101,B11111011,B11111111,B11111100,B11101111,B11011111,B10000000, + B00000111,B11111111,B11111111,B00111110,B01110000,B11111111,B11110000,B11110011,B11011111,B11000000, + B00000011,B11111111,B11111100,B00111111,B10000000,B00001111,B10000000,B01111101,B10111111,B11000000, + B00000001,B11111111,B11111000,B00011111,B11011000,B00000000,B00000000,B11111111,B10111111,B10000000, + B00000001,B11111111,B11100000,B00001111,B11011111,B00000000,B00000001,B11111111,B00011111,B10000000, + B00000000,B01111111,B11000000,B00001111,B11111111,B10000000,B00000011,B11111110,B00011111,B00000000, + B00000000,B00111111,B10000000,B00001111,B10111111,B10000000,B00000011,B11111000,B00111111,B00000000, + B00000000,B00111111,B00000000,B00001111,B10011111,B11000000,B00000111,B11000000,B00111110,B00000000, + B00000000,B00011100,B00000000,B00011111,B00000000,B11000000,B00001111,B11000000,B01111110,B00000000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000, + B00000011,B10001100,B01110000,B11100000,B11100000,B11001100,B00011100,B00011000,B00000111,B11000000, + B00000011,B10011100,B01110000,B11110000,B11110001,B11001110,B00011100,B00111100,B00001111,B11100000, + B00000011,B10011100,B01110001,B11110000,B11110001,B11001110,B00011100,B00111100,B00011111,B11110000, + B00000011,B10011100,B01110001,B11110000,B11111001,B11001110,B00011100,B01111110,B00111100,B01111000, + B00000011,B10011100,B01110001,B11111000,B11111101,B11001111,B11111100,B01111110,B00111000,B00111000, + B00000001,B10011110,B11100011,B10111000,B11111111,B11001111,B11111100,B01100111,B00111000,B00011000, + B00000001,B11011110,B11100011,B10111000,B11101111,B11001111,B11111100,B11100111,B00111000,B00111000, + B00000001,B11111111,B11000011,B11111100,B11100111,B11001110,B00011100,B11111111,B00111100,B00111000, + B00000000,B11110111,B11000111,B11111100,B11100011,B11001110,B00011100,B11111111,B10011111,B11110000, + B00000000,B11110011,B10000111,B00011110,B11100011,B11001110,B00011101,B11100011,B10001111,B11110000, + B00000000,B01110011,B10000111,B00001110,B11100001,B11001110,B00011101,B11000011,B11000111,B11000000 +}; diff --git a/config/examples/adafruit/ST7565/Configuration.h b/config/examples/adafruit/ST7565/Configuration.h index 989f3ef8ac..c7ce14d12c 100644 --- a/config/examples/adafruit/ST7565/Configuration.h +++ b/config/examples/adafruit/ST7565/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2037,7 +2038,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/delta/Anycubic/Kossel/Configuration.h b/config/examples/delta/Anycubic/Kossel/Configuration.h index 109fef80db..3dc1a75c3c 100644 --- a/config/examples/delta/Anycubic/Kossel/Configuration.h +++ b/config/examples/delta/Anycubic/Kossel/Configuration.h @@ -374,6 +374,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -417,7 +418,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -2225,7 +2226,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h index 5bb977c044..c7731ea488 100644 --- a/config/examples/delta/Anycubic/Kossel/Configuration_adv.h +++ b/config/examples/delta/Anycubic/Kossel/Configuration_adv.h @@ -659,10 +659,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full // (don't use SLOWDOWN with DELTA because DELTA generates hundreds of segments per second) @@ -853,11 +853,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + #define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -882,23 +903,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -933,6 +937,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/delta/Dreammaker/Overlord/Configuration.h b/config/examples/delta/Dreammaker/Overlord/Configuration.h index 825617c2e5..f5fd8dda18 100644 --- a/config/examples/delta/Dreammaker/Overlord/Configuration.h +++ b/config/examples/delta/Dreammaker/Overlord/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 201 #define TEMP_SENSOR_1 201 @@ -2161,7 +2162,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h b/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h index 0440ca06f5..6f1c6176b6 100644 --- a/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h +++ b/config/examples/delta/Dreammaker/Overlord/Configuration_adv.h @@ -659,10 +659,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full // (don't use SLOWDOWN with DELTA because DELTA generates hundreds of segments per second) @@ -853,11 +853,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + #define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + #define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 35 // User defined RED value + #define LED_USER_PRESET_GREEN 35 // User defined GREEN value + #define LED_USER_PRESET_BLUE 35 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + #define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -882,23 +903,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 35 // User defined RED value - #define LED_USER_PRESET_GREEN 35 // User defined GREEN value - #define LED_USER_PRESET_BLUE 35 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - #define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -933,6 +937,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss (optional) #define POWER_LOSS_STATE LOW // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h index a6c09b86ce..bb6c680364 100644 --- a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h +++ b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 201 #define TEMP_SENSOR_1 201 @@ -2172,7 +2173,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h index 0440ca06f5..6f1c6176b6 100644 --- a/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h +++ b/config/examples/delta/Dreammaker/Overlord_Pro/Configuration_adv.h @@ -659,10 +659,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full // (don't use SLOWDOWN with DELTA because DELTA generates hundreds of segments per second) @@ -853,11 +853,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + #define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + #define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 35 // User defined RED value + #define LED_USER_PRESET_GREEN 35 // User defined GREEN value + #define LED_USER_PRESET_BLUE 35 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + #define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view #define STATUS_MESSAGE_SCROLLING @@ -882,23 +903,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 35 // User defined RED value - #define LED_USER_PRESET_GREEN 35 // User defined GREEN value - #define LED_USER_PRESET_BLUE 35 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - #define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -933,6 +937,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss (optional) #define POWER_LOSS_STATE LOW // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h index 60f81d01cc..96cc4c4524 100644 --- a/config/examples/delta/FLSUN/auto_calibrate/Configuration.h +++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -2165,7 +2166,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h index f22e89662e..b06a7e75c2 100644 --- a/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h +++ b/config/examples/delta/FLSUN/auto_calibrate/Configuration_adv.h @@ -659,10 +659,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full // (don't use SLOWDOWN with DELTA because DELTA generates hundreds of segments per second) @@ -853,11 +853,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -882,23 +903,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -933,6 +937,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/delta/FLSUN/kossel/Configuration.h b/config/examples/delta/FLSUN/kossel/Configuration.h index 4eba85b0e4..b08507c154 100644 --- a/config/examples/delta/FLSUN/kossel/Configuration.h +++ b/config/examples/delta/FLSUN/kossel/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -2164,7 +2165,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/delta/FLSUN/kossel/Configuration_adv.h b/config/examples/delta/FLSUN/kossel/Configuration_adv.h index f22e89662e..b06a7e75c2 100644 --- a/config/examples/delta/FLSUN/kossel/Configuration_adv.h +++ b/config/examples/delta/FLSUN/kossel/Configuration_adv.h @@ -659,10 +659,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full // (don't use SLOWDOWN with DELTA because DELTA generates hundreds of segments per second) @@ -853,11 +853,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -882,23 +903,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -933,6 +937,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration.h b/config/examples/delta/FLSUN/kossel_mini/Configuration.h index f5f3f7cbbb..ef5de2be23 100644 --- a/config/examples/delta/FLSUN/kossel_mini/Configuration.h +++ b/config/examples/delta/FLSUN/kossel_mini/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2164,7 +2165,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h index 46dc45c49f..2b06f03fd0 100644 --- a/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h +++ b/config/examples/delta/FLSUN/kossel_mini/Configuration_adv.h @@ -659,10 +659,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full // (don't use SLOWDOWN with DELTA because DELTA generates hundreds of segments per second) @@ -853,11 +853,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -882,23 +903,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -933,6 +937,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration.h b/config/examples/delta/Geeetech/Rostock 301/Configuration.h index 9108cd1bfe..6454511aa1 100644 --- a/config/examples/delta/Geeetech/Rostock 301/Configuration.h +++ b/config/examples/delta/Geeetech/Rostock 301/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -2153,7 +2154,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h index 5e6483ffe1..f9dd4fd1ac 100644 --- a/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h +++ b/config/examples/delta/Geeetech/Rostock 301/Configuration_adv.h @@ -659,10 +659,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full // (don't use SLOWDOWN with DELTA because DELTA generates hundreds of segments per second) @@ -853,11 +853,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -882,23 +903,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -933,6 +937,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/delta/Hatchbox_Alpha/Configuration.h b/config/examples/delta/Hatchbox_Alpha/Configuration.h index 984cc0093c..23fc866970 100644 --- a/config/examples/delta/Hatchbox_Alpha/Configuration.h +++ b/config/examples/delta/Hatchbox_Alpha/Configuration.h @@ -364,6 +364,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -407,7 +408,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -2167,7 +2168,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/delta/MKS/SBASE/Configuration.h b/config/examples/delta/MKS/SBASE/Configuration.h index d6fa3ebc81..62fb01c21f 100644 --- a/config/examples/delta/MKS/SBASE/Configuration.h +++ b/config/examples/delta/MKS/SBASE/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 -1 #define TEMP_SENSOR_1 0 @@ -2152,7 +2153,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/delta/MKS/SBASE/Configuration_adv.h b/config/examples/delta/MKS/SBASE/Configuration_adv.h index 4a3b06c8f0..dcafbef8d8 100644 --- a/config/examples/delta/MKS/SBASE/Configuration_adv.h +++ b/config/examples/delta/MKS/SBASE/Configuration_adv.h @@ -659,10 +659,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full // (don't use SLOWDOWN with DELTA because DELTA generates hundreds of segments per second) @@ -853,11 +853,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -882,23 +903,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -933,6 +937,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/delta/Tevo Little Monster/Configuration.h b/config/examples/delta/Tevo Little Monster/Configuration.h index 9416c873fb..47008a5af9 100644 --- a/config/examples/delta/Tevo Little Monster/Configuration.h +++ b/config/examples/delta/Tevo Little Monster/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2156,7 +2157,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/delta/Tevo Little Monster/Configuration_adv.h b/config/examples/delta/Tevo Little Monster/Configuration_adv.h index e247e27ea1..d1ded32ff1 100644 --- a/config/examples/delta/Tevo Little Monster/Configuration_adv.h +++ b/config/examples/delta/Tevo Little Monster/Configuration_adv.h @@ -659,10 +659,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full // (don't use SLOWDOWN with DELTA because DELTA generates hundreds of segments per second) @@ -853,11 +853,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -882,23 +903,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -933,6 +937,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/delta/generic/Configuration.h b/config/examples/delta/generic/Configuration.h index 23d2be1f87..36bc0f9743 100644 --- a/config/examples/delta/generic/Configuration.h +++ b/config/examples/delta/generic/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 -1 #define TEMP_SENSOR_1 0 @@ -2152,7 +2153,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/delta/generic/Configuration_adv.h b/config/examples/delta/generic/Configuration_adv.h index 46dc45c49f..2b06f03fd0 100644 --- a/config/examples/delta/generic/Configuration_adv.h +++ b/config/examples/delta/generic/Configuration_adv.h @@ -659,10 +659,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full // (don't use SLOWDOWN with DELTA because DELTA generates hundreds of segments per second) @@ -853,11 +853,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -882,23 +903,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -933,6 +937,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/delta/kossel_mini/Configuration.h b/config/examples/delta/kossel_mini/Configuration.h index 60f200c2ca..1ba1c3c058 100644 --- a/config/examples/delta/kossel_mini/Configuration.h +++ b/config/examples/delta/kossel_mini/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 7 #define TEMP_SENSOR_1 0 @@ -2154,7 +2155,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/delta/kossel_mini/Configuration_adv.h b/config/examples/delta/kossel_mini/Configuration_adv.h index 46dc45c49f..2b06f03fd0 100644 --- a/config/examples/delta/kossel_mini/Configuration_adv.h +++ b/config/examples/delta/kossel_mini/Configuration_adv.h @@ -659,10 +659,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full // (don't use SLOWDOWN with DELTA because DELTA generates hundreds of segments per second) @@ -853,11 +853,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -882,23 +903,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -933,6 +937,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/delta/kossel_pro/Configuration.h b/config/examples/delta/kossel_pro/Configuration.h index ee40890691..0e60a8489f 100644 --- a/config/examples/delta/kossel_pro/Configuration.h +++ b/config/examples/delta/kossel_pro/Configuration.h @@ -363,6 +363,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -406,7 +407,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -2155,7 +2156,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/delta/kossel_xl/Configuration.h b/config/examples/delta/kossel_xl/Configuration.h index 607a96c558..77bc7bfa29 100644 --- a/config/examples/delta/kossel_xl/Configuration.h +++ b/config/examples/delta/kossel_xl/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -2155,7 +2156,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/delta/kossel_xl/Configuration_adv.h b/config/examples/delta/kossel_xl/Configuration_adv.h index 7058837817..a75b12f0b8 100644 --- a/config/examples/delta/kossel_xl/Configuration_adv.h +++ b/config/examples/delta/kossel_xl/Configuration_adv.h @@ -659,10 +659,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full // (don't use SLOWDOWN with DELTA because DELTA generates hundreds of segments per second) @@ -853,11 +853,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -882,23 +903,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -933,6 +937,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/gCreate/gMax1.5+/Configuration.h b/config/examples/gCreate/gMax1.5+/Configuration.h index 8095c191a7..2f7791fcdc 100644 --- a/config/examples/gCreate/gMax1.5+/Configuration.h +++ b/config/examples/gCreate/gMax1.5+/Configuration.h @@ -364,6 +364,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -407,7 +408,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -2051,7 +2052,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/gCreate/gMax1.5+/Configuration_adv.h b/config/examples/gCreate/gMax1.5+/Configuration_adv.h index 70f752765d..00196f5466 100644 --- a/config/examples/gCreate/gMax1.5+/Configuration_adv.h +++ b/config/examples/gCreate/gMax1.5+/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/makibox/Configuration.h b/config/examples/makibox/Configuration.h index b7844cd985..8d92ca60e3 100644 --- a/config/examples/makibox/Configuration.h +++ b/config/examples/makibox/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 1 #define TEMP_SENSOR_1 0 @@ -2040,7 +2041,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/makibox/Configuration_adv.h b/config/examples/makibox/Configuration_adv.h index e82d49fb91..7d67db7b58 100644 --- a/config/examples/makibox/Configuration_adv.h +++ b/config/examples/makibox/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/tvrrug/Round2/Configuration.h b/config/examples/tvrrug/Round2/Configuration.h index 6942f607a1..9475b3baee 100644 --- a/config/examples/tvrrug/Round2/Configuration.h +++ b/config/examples/tvrrug/Round2/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 5 #define TEMP_SENSOR_1 0 @@ -2032,7 +2033,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/tvrrug/Round2/Configuration_adv.h b/config/examples/tvrrug/Round2/Configuration_adv.h index b82f0c37ec..02f4f8fed5 100644 --- a/config/examples/tvrrug/Round2/Configuration_adv.h +++ b/config/examples/tvrrug/Round2/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -851,11 +851,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -//#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + //#define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -880,23 +901,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -931,6 +935,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/config/examples/wt150/Configuration.h b/config/examples/wt150/Configuration.h index 17e4ffe2b4..b37191722c 100644 --- a/config/examples/wt150/Configuration.h +++ b/config/examples/wt150/Configuration.h @@ -359,6 +359,7 @@ * -1 : thermocouple with AD595 * 0 : not used * 1 : 100k thermistor - best choice for EPCOS 100k (4.7k pullup) + * 331 : (3.3V scaled thermistor 1 table) * 2 : 200k thermistor - ATC Semitec 204GT-2 (4.7k pullup) * 3 : Mendel-parts thermistor (4.7k pullup) * 4 : 10k thermistor !! do not use it for a hotend. It gives bad resolution at high temp. !! @@ -402,7 +403,7 @@ * 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below. * 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below. * - * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } + * :{ '0':"Not used", '1':"100k / 4.7k - EPCOS", '331':"(3.3V thermistor 1)", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '512':"100k RPW-Ultra hotend thermistor", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950 1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '18':"ATC Semitec 204GT-2 (4.7k pullup) Dagoma.Fr - MKS_Base_DKU001327" '20':"Pt100 (Ultimainboard V2.x)", '201':"Pt100 (Overlord)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '61':"100k Formbot / Vivedino 3950 350C thermistor 4.7k pullup", '66':"Dyze Design 4.7M High Temperature thermistor", '67':"Slice Engineering 450C High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595", '998':"Dummy 1", '999':"Dummy 2", '1000':"Custom thermistor params" } */ #define TEMP_SENSOR_0 -2 #define TEMP_SENSOR_1 0 @@ -2042,7 +2043,7 @@ // LulzBot Color Touch UI for FTDI EVE (FT800/FT810) displays // See Configuration_adv.h for all configuration options. // -//#defined LULZBOT_TOUCH_UI +//#define LULZBOT_TOUCH_UI // // Third-party or vendor-customized controller interfaces. diff --git a/config/examples/wt150/Configuration_adv.h b/config/examples/wt150/Configuration_adv.h index 208525eeee..6cc8fdf77e 100644 --- a/config/examples/wt150/Configuration_adv.h +++ b/config/examples/wt150/Configuration_adv.h @@ -658,10 +658,10 @@ #endif #endif -// @section extras +// @section motion -// minimum time in microseconds that a movement needs to take if the buffer is emptied. -#define DEFAULT_MINSEGMENTTIME 20000 +// Minimum time that a segment needs to take if the buffer is emptied +#define DEFAULT_MINSEGMENTTIME 20000 // (ms) // If defined the movements slow down when the look ahead buffer is only half full #define SLOWDOWN @@ -852,11 +852,32 @@ #define FEEDRATE_CHANGE_BEEP_FREQUENCY 440 #endif -// Include a page of printer information in the LCD Main Menu -#define LCD_INFO_MENU -#if ENABLED(LCD_INFO_MENU) - //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages -#endif +#if HAS_LCD_MENU + + // Include a page of printer information in the LCD Main Menu + #define LCD_INFO_MENU + #if ENABLED(LCD_INFO_MENU) + //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages + #endif + + /** + * LED Control Menu + * Add LED Control to the LCD menu + */ + //#define LED_CONTROL_MENU + #if ENABLED(LED_CONTROL_MENU) + #define LED_COLOR_PRESETS // Enable the Preset Color menu option + #if ENABLED(LED_COLOR_PRESETS) + #define LED_USER_PRESET_RED 255 // User defined RED value + #define LED_USER_PRESET_GREEN 128 // User defined GREEN value + #define LED_USER_PRESET_BLUE 0 // User defined BLUE value + #define LED_USER_PRESET_WHITE 255 // User defined WHITE value + #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup + #endif + #endif + +#endif // HAS_LCD_MENU // Scroll a longer status message into view //#define STATUS_MESSAGE_SCROLLING @@ -881,23 +902,6 @@ #endif #endif -/** - * LED Control Menu - * Enable this feature to add LED Control to the LCD menu - */ -//#define LED_CONTROL_MENU -#if ENABLED(LED_CONTROL_MENU) - #define LED_COLOR_PRESETS // Enable the Preset Color menu option - #if ENABLED(LED_COLOR_PRESETS) - #define LED_USER_PRESET_RED 255 // User defined RED value - #define LED_USER_PRESET_GREEN 128 // User defined GREEN value - #define LED_USER_PRESET_BLUE 0 // User defined BLUE value - #define LED_USER_PRESET_WHITE 255 // User defined WHITE value - #define LED_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup - #endif -#endif // LED_CONTROL_MENU - #if ENABLED(SDSUPPORT) // Some RAMPS and other boards don't detect when an SD card is inserted. You can work @@ -932,6 +936,7 @@ #if ENABLED(POWER_LOSS_RECOVERY) //#define POWER_LOSS_PIN 44 // Pin to detect power loss //#define POWER_LOSS_STATE HIGH // State of pin indicating power loss + //#define POWER_LOSS_PULL // Set pullup / pulldown as appropriate //#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power. diff --git a/platformio.ini b/platformio.ini index d62388726a..c4d20e9c98 100644 --- a/platformio.ini +++ b/platformio.ini @@ -32,7 +32,6 @@ lib_deps = Adafruit NeoPixel@1.1.3 LiquidTWI2=https://github.com/lincomatic/LiquidTWI2/archive/master.zip Arduino-L6470=https://github.com/ameyer/Arduino-L6470/archive/dev.zip - TMC26XStepper=https://github.com/trinamic/TMC26XStepper/archive/master.zip SailfishLCD=https://github.com/mikeshub/SailfishLCD/archive/master.zip SailfishRGB_LED=https://github.com/mikeshub/SailfishRGB_LED/archive/master.zip SlowSoftI2CMaster=https://github.com/mikeshub/SlowSoftI2CMaster/archive/master.zip @@ -57,6 +56,7 @@ board = megaatmega2560 build_flags = ${common.build_flags} board_build.f_cpu = 16000000L lib_deps = ${common.lib_deps} + TMC26XStepper=https://github.com/trinamic/TMC26XStepper/archive/master.zip src_filter = ${common.default_src_filter} + monitor_speed = 250000 @@ -70,6 +70,7 @@ board = megaatmega1280 build_flags = ${common.build_flags} board_build.f_cpu = 16000000L lib_deps = ${common.lib_deps} + TMC26XStepper=https://github.com/trinamic/TMC26XStepper/archive/master.zip src_filter = ${common.default_src_filter} + monitor_speed = 250000 @@ -86,6 +87,7 @@ framework = arduino board = at90usb1286 build_flags = ${common.build_flags} lib_deps = ${common.lib_deps} + TMC26XStepper=https://github.com/trinamic/TMC26XStepper/archive/master.zip src_filter = ${common.default_src_filter} + extra_scripts = pre:buildroot/share/atom/create_custom_upload_command_CDC.py monitor_speed = 250000 @@ -102,6 +104,7 @@ framework = arduino board = at90usb1286 build_flags = ${common.build_flags} lib_deps = ${common.lib_deps} + TMC26XStepper=https://github.com/trinamic/TMC26XStepper/archive/master.zip src_filter = ${common.default_src_filter} + extra_scripts = pre:buildroot/share/atom/create_custom_upload_command_DFU.py monitor_speed = 250000 @@ -118,7 +121,6 @@ framework = arduino board = due build_flags = ${common.build_flags} lib_deps = ${common.lib_deps} -lib_ignore = TMC26XStepper src_filter = ${common.default_src_filter} + monitor_speed = 250000 [env:DUE_USB] @@ -127,7 +129,6 @@ framework = arduino board = dueUSB build_flags = ${common.build_flags} lib_deps = ${common.lib_deps} -lib_ignore = TMC26XStepper src_filter = ${common.default_src_filter} + monitor_speed = 250000 [env:DUE_debug] @@ -139,7 +140,6 @@ build_flags = ${common.build_flags} -funwind-tables -mpoke-function-name lib_deps = ${common.lib_deps} -lib_ignore = TMC26XStepper src_filter = ${common.default_src_filter} + monitor_speed = 250000 @@ -195,7 +195,7 @@ board = sanguino_atmega1284p build_flags = ${common.build_flags} -fmerge-all-constants upload_speed = 57600 lib_deps = ${common.lib_deps} -lib_ignore = TMCStepper, TMC26XStepper +lib_ignore = TMCStepper src_filter = ${common.default_src_filter} + monitor_speed = 250000 @@ -209,7 +209,7 @@ board = sanguino_atmega1284p build_flags = ${common.build_flags} upload_speed = 115200 lib_deps = ${common.lib_deps} -lib_ignore = TMCStepper, TMC26XStepper +lib_ignore = TMCStepper src_filter = ${common.default_src_filter} + monitor_speed = 250000 @@ -223,6 +223,7 @@ board = reprap_rambo build_flags = ${common.build_flags} board_build.f_cpu = 16000000L lib_deps = ${common.lib_deps} + TMC26XStepper=https://github.com/trinamic/TMC26XStepper/archive/master.zip src_filter = ${common.default_src_filter} + monitor_speed = 250000 @@ -235,6 +236,7 @@ framework = arduino board = sanguino_atmega644p build_flags = ${common.build_flags} lib_deps = ${common.lib_deps} + TMC26XStepper=https://github.com/trinamic/TMC26XStepper/archive/master.zip src_filter = ${common.default_src_filter} + monitor_speed = 250000 @@ -247,6 +249,7 @@ framework = arduino board = sanguino_atmega1284p build_flags = ${common.build_flags} lib_deps = ${common.lib_deps} + TMC26XStepper=https://github.com/trinamic/TMC26XStepper/archive/master.zip src_filter = ${common.default_src_filter} + monitor_speed = 250000 @@ -262,14 +265,7 @@ build_flags = !python Marlin/src/HAL/HAL_STM32F1/STM32F1_flag_script.py -DDEBUG_LEVEL=0 build_unflags = -std=gnu++11 lib_deps = ${common.lib_deps} -lib_ignore = U8glib-HAL - TMC26XStepper - libf3c - lib066 - Adafruit NeoPixel_ID28 - Adafruit NeoPixel - libf3e -#lib_ldf_mode = chain +lib_ignore = U8glib-HAL, Adafruit NeoPixel src_filter = ${common.default_src_filter} + monitor_speed = 250000 @@ -277,52 +273,44 @@ monitor_speed = 250000 # fysetc_STM32F1 # [env:fysetc_STM32F1] -platform = ststm32 -framework = arduino -board = genericSTM32F103RC -extra_scripts = buildroot/share/PlatformIO/scripts/fysetc_STM32F1.py -build_flags = !python Marlin/src/HAL/HAL_STM32F1/STM32F1_flag_script.py +platform = ststm32 +framework = arduino +board = genericSTM32F103RC +#board_build.core = maple +platform_packages = tool-stm32duino +extra_scripts = buildroot/share/PlatformIO/scripts/fysetc_STM32F1.py +build_flags = !python Marlin/src/HAL/HAL_STM32F1/STM32F1_flag_script.py ${common.build_flags} -std=gnu++14 -DDEBUG_LEVEL=0 -DHAVE_SW_SERIAL -build_unflags = -std=gnu++11 -lib_deps = ${common.lib_deps} +build_unflags = -std=gnu++11 +lib_deps = ${common.lib_deps} SoftwareSerialM=https://github.com/FYSETC/SoftwareSerialM/archive/master.zip -lib_ignore = TMC26XStepper - libf3c - lib066 - Adafruit NeoPixel_ID28 - Adafruit NeoPixel - libf3e -lib_ldf_mode = chain -src_filter = ${common.default_src_filter} + -monitor_speed = 250000 -debug_tool = stlink -upload_protocol = serial +lib_ignore = Adafruit NeoPixel +lib_ldf_mode = chain +src_filter = ${common.default_src_filter} + +monitor_speed = 250000 +debug_tool = stlink +upload_protocol = serial # # BigTree SKR Mini V1.1 / SKR mini E3 / SKR E3 DIP (STM32F103RCT6 ARM Cortex-M3) # [env:BIGTREE_SKR_MINI] -platform = ststm32 -framework = arduino -board = genericSTM32F103RC -extra_scripts = buildroot/share/PlatformIO/scripts/STM32F1_SKR_MINI.py -build_flags = !python Marlin/src/HAL/HAL_STM32F1/STM32F1_flag_script.py +platform = ststm32 +framework = arduino +board = genericSTM32F103RC +platform_packages = tool-stm32duino +extra_scripts = buildroot/share/PlatformIO/scripts/STM32F1_SKR_MINI.py +build_flags = !python Marlin/src/HAL/HAL_STM32F1/STM32F1_flag_script.py ${common.build_flags} -std=gnu++14 -DDEBUG_LEVEL=0 -build_unflags = -std=gnu++11 -lib_deps = ${common.lib_deps} -lib_ignore = TMC26XStepper - libf3c - lib066 - Adafruit NeoPixel_ID28 - Adafruit NeoPixel - libf3e -#lib_ldf_mode = chain -src_filter = ${common.default_src_filter} + -monitor_speed = 115200 -upload_protocol = stlink -debug_tool = stlink +build_unflags = -std=gnu++11 +lib_deps = ${common.lib_deps} +lib_ignore = Adafruit NeoPixel +src_filter = ${common.default_src_filter} + +monitor_speed = 115200 +upload_protocol = stlink +debug_tool = stlink # # STM32F4 with STM32GENERIC @@ -331,10 +319,10 @@ debug_tool = stlink platform = ststm32 framework = arduino board = disco_f407vg -build_flags = ${common.build_flags} -DUSE_STM32GENERIC -DSTM32GENERIC -DMENU_USB_SERIAL -DMENU_SERIAL=SerialUSB +build_flags = ${common.build_flags} -DUSE_STM32GENERIC -DSTM32GENERIC -DSTM32F4 -DMENU_USB_SERIAL -DMENU_SERIAL=SerialUSB lib_deps = ${common.lib_deps} -lib_ignore = Adafruit NeoPixel, TMC26XStepper, TMCStepper -src_filter = ${common.default_src_filter} + - + +lib_ignore = Adafruit NeoPixel, TMCStepper +src_filter = ${common.default_src_filter} + - monitor_speed = 250000 # @@ -343,11 +331,11 @@ monitor_speed = 250000 [env:STM32F7] platform = ststm32 framework = arduino -board = disco_f765vg -build_flags = ${common.build_flags} -DUSE_STM32GENERIC -DSTM32GENERIC -DMENU_USB_SERIAL -DMENU_SERIAL=SerialUSB +board = remram_v1 +build_flags = ${common.build_flags} -DUSE_STM32GENERIC -DSTM32GENERIC -DSTM32F7 -DMENU_USB_SERIAL -DMENU_SERIAL=SerialUSB lib_deps = ${common.lib_deps} -lib_ignore = Adafruit NeoPixel, TMC26XStepper, TMCStepper -src_filter = ${common.default_src_filter} + - + +lib_ignore = Adafruit NeoPixel, TMCStepper +src_filter = ${common.default_src_filter} + - monitor_speed = 250000 # @@ -359,12 +347,12 @@ framework = arduino board = armed_v1 build_flags = ${common.build_flags} -DUSBCON -DUSBD_VID=0x0483 '-DUSB_MANUFACTURER="Unknown"' '-DUSB_PRODUCT="ARMED_V1"' -DHAL_PCD_MODULE_ENABLED -DUSBD_USE_CDC -O2 -ffreestanding -fsigned-char -fno-move-loop-invariants -fno-strict-aliasing -std=gnu11 -std=gnu++11 lib_deps = ${common.lib_deps} -lib_ignore = Adafruit NeoPixel, TMC26XStepper +lib_ignore = Adafruit NeoPixel src_filter = ${common.default_src_filter} + monitor_speed = 250000 # -# Alfawise U20 (STM32F103VET6) +# Longer 3D board in Alfawise U20 (STM32F103VET6) # [env:alfawise_U20] platform = ststm32 @@ -378,12 +366,7 @@ build_flags = !python Marlin/src/HAL/HAL_STM32F1/STM32F1_flag_script.py build_unflags = -std=gnu++11 -DCONFIG_MAPLE_MINI_NO_DISABLE_DEBUG=1 src_filter = ${common.default_src_filter} + lib_deps = ${common.lib_deps} -lib_ignore = TMC26XStepper - libf3c - lib066 - Adafruit NeoPixel_ID28 - Adafruit NeoPixel - libf3e +lib_ignore = Adafruit NeoPixel # # MKS Robin (STM32F103ZET6) @@ -398,13 +381,7 @@ build_flags = !python Marlin/src/HAL/HAL_STM32F1/STM32F1_flag_script.py build_unflags = -std=gnu++11 src_filter = ${common.default_src_filter} + lib_deps = ${common.lib_deps} -lib_ignore = TMC26XStepper - libf3c - lib066 - Adafruit NeoPixel_ID28 - Adafruit NeoPixel - libf3e - U8glib-HAL +lib_ignore = Adafruit NeoPixel # # MKS ROBIN LITE/LITE2 (STM32F103RCT6) @@ -419,12 +396,7 @@ build_flags = !python Marlin/src/HAL/HAL_STM32F1/STM32F1_flag_script.py build_unflags = -std=gnu++11 src_filter = ${common.default_src_filter} + lib_deps = ${common.lib_deps} -lib_ignore = TMC26XStepper - libf3c - lib066 - Adafruit NeoPixel_ID28 - Adafruit NeoPixel - libf3e +lib_ignore = Adafruit NeoPixel # # MKS Robin Mini (STM32F103VET6) @@ -439,12 +411,7 @@ build_flags = !python Marlin/src/HAL/HAL_STM32F1/STM32F1_flag_script.py build_unflags = -std=gnu++11 src_filter = ${common.default_src_filter} + lib_deps = ${common.lib_deps} -lib_ignore = TMC26XStepper - libf3c - lib066 - Adafruit NeoPixel_ID28 - Adafruit NeoPixel - libf3e +lib_ignore = Adafruit NeoPixel # # MKS Robin Nano (STM32F103VET6) @@ -459,12 +426,7 @@ build_flags = !python Marlin/src/HAL/HAL_STM32F1/STM32F1_flag_script.py build_unflags = -std=gnu++11 src_filter = ${common.default_src_filter} + lib_deps = ${common.lib_deps} -lib_ignore = TMC26XStepper - libf3c - lib066 - Adafruit NeoPixel_ID28 - Adafruit NeoPixel - libf3e +lib_ignore = Adafruit NeoPixel # # JGAurora A5S A1 (STM32F103ZET6) @@ -479,12 +441,7 @@ build_flags = !python Marlin/src/HAL/HAL_STM32F1/STM32F1_flag_script.py build_unflags = -std=gnu++11 src_filter = ${common.default_src_filter} + lib_deps = ${common.lib_deps} -lib_ignore = TMC26XStepper - libf3c - lib066 - Adafruit NeoPixel_ID28 - Adafruit NeoPixel - libf3e +lib_ignore = Adafruit NeoPixel monitor_speed = 250000 # @@ -498,14 +455,14 @@ framework = arduino board = blackSTM32F407VET6 extra_scripts = pre:buildroot/share/PlatformIO/scripts/black_stm32f407vet6.py build_flags = ${common.build_flags} - -DUSBCON -DUSBD_USE_CDC -DUSBD_VID=0x0483 -DUSB_PRODUCT=\"BLACK_F407VE\" + -DSTM32F4 -DUSBCON -DUSBD_USE_CDC -DUSBD_VID=0x0483 -DUSB_PRODUCT=\"BLACK_F407VE\" lib_deps = ${common.lib_deps} -lib_ignore = Adafruit NeoPixel, TMC26XStepper, TMCStepper, SailfishLCD, SailfishRGB_LED, SlowSoftI2CMaster +lib_ignore = Adafruit NeoPixel, TMCStepper, SailfishLCD, SailfishRGB_LED, SlowSoftI2CMaster src_filter = ${common.default_src_filter} + monitor_speed = 250000 # -# BIGTREE_SKR_PRO (STM32F407ZGT6 ARM Cortex-M4) +# Bigtreetech SKR Pro (STM32F407ZGT6 ARM Cortex-M4) # [env:BIGTREE_SKR_PRO] platform = ststm32@5.4.3 @@ -516,7 +473,27 @@ build_flags = ${common.build_flags} -DUSBCON -DUSBD_USE_CDC -DUSBD_VID=0x0483 -DUSB_PRODUCT=\"STM32F407ZG\" -DTARGET_STM32F4 -DSTM32F407_5ZX -DVECT_TAB_OFFSET=0x8000 -DHAVE_HWSERIAL6 lib_deps = ${common.lib_deps} -lib_ignore = Adafruit NeoPixel, TMC26XStepper, SailfishLCD, SailfishRGB_LED, SlowSoftI2CMaster +lib_ignore = Adafruit NeoPixel, SailfishLCD, SailfishRGB_LED, SlowSoftI2CMaster +src_filter = ${common.default_src_filter} + +monitor_speed = 250000 + +# +# BIGTREE_SKR_BTT002 (STM32F407VET6 ARM Cortex-M4) +# +[env:BIGTREE_BTT002] +platform = ststm32@5.4.3 +framework = arduino +board = BigTree_BTT002 +extra_scripts = pre:buildroot/share/PlatformIO/scripts/generic_create_variant.py +build_flags = ${common.build_flags} + -DUSBCON -DUSBD_USE_CDC -DUSBD_VID=0x0483 -DUSB_PRODUCT=\"STM32F407VE\" + -DTARGET_STM32F4 -DSTM32F407_5VX -DVECT_TAB_OFFSET=0x8000 + -DHAVE_HWSERIAL2 + -DHAVE_HWSERIAL3 + -DPIN_SERIAL2_RX=PD_6 + -DPIN_SERIAL2_TX=PD_5 +lib_deps = ${common.lib_deps} +lib_ignore = Adafruit NeoPixel, SailfishLCD, SailfishRGB_LED, SlowSoftI2CMaster src_filter = ${common.default_src_filter} + monitor_speed = 250000 @@ -529,6 +506,7 @@ framework = arduino board = teensy31 build_flags = ${common.build_flags} lib_deps = ${common.lib_deps} + TMC26XStepper=https://github.com/trinamic/TMC26XStepper/archive/master.zip lib_ignore = Adafruit NeoPixel src_filter = ${common.default_src_filter} + monitor_speed = 250000 @@ -542,6 +520,7 @@ framework = arduino board = teensy35 build_flags = ${common.build_flags} lib_deps = ${common.lib_deps} + TMC26XStepper=https://github.com/trinamic/TMC26XStepper/archive/master.zip lib_ignore = Adafruit NeoPixel src_filter = ${common.default_src_filter} + monitor_speed = 250000 @@ -557,16 +536,7 @@ build_flags = !python Marlin/src/HAL/HAL_STM32F1/STM32F1_flag_script.py -DMCU_ST -DDEBUG_LEVEL=0 src_filter = ${common.default_src_filter} + #- -lib_ignore = Adafruit NeoPixel - U8glib - LiquidCrystal_I2C - LiquidCrystal - NewliquidCrystal - LiquidTWI2 - TMC26XStepper - TMCStepper - Servo(STM32F1) - U8glib-HAL +lib_ignore = Adafruit NeoPixel, LiquidCrystal, LiquidTWI2, TMCStepper, U8glib-HAL # # Espressif ESP32 @@ -581,13 +551,7 @@ upload_port = /dev/ttyUSB0 lib_deps = AsyncTCP=https://github.com/me-no-dev/AsyncTCP/archive/master.zip ESPAsyncWebServer=https://github.com/me-no-dev/ESPAsyncWebServer/archive/master.zip -lib_ignore = TMC26XStepper - LiquidCrystal_I2C - LiquidCrystal - NewliquidCrystal - LiquidTWI2 - SailfishLCD - SailfishRGB_LED +lib_ignore = LiquidCrystal, LiquidTWI2, SailfishLCD, SailfishRGB_LED src_filter = ${common.default_src_filter} + # @@ -600,6 +564,7 @@ board = fysetc_f6_13 build_flags = ${common.build_flags} board_build.f_cpu = 16000000L lib_deps = ${common.lib_deps} + TMC26XStepper=https://github.com/trinamic/TMC26XStepper/archive/master.zip src_filter = ${common.default_src_filter} + monitor_speed = 250000 @@ -627,6 +592,6 @@ framework = arduino build_flags = ${common.build_flags} -std=gnu++17 build_unflags = -std=gnu++11 lib_deps = ${common.lib_deps} -lib_ignore = U8glib-HAL, TMC26XStepper +lib_ignore = U8glib-HAL src_filter = ${common.default_src_filter} + debug_tool = jlink