From d21d6f6c9eced9e31958f126b5c283cfb149d536 Mon Sep 17 00:00:00 2001
From: InsanityAutomation
<38436470+InsanityAutomation@users.noreply.github.com>
Date: Sun, 15 Mar 2020 14:44:41 -0400
Subject: [PATCH] Support all but motion
---
Marlin/Configuration.h | 15 ++--
Marlin/Configuration_adv.h | 6 +-
Marlin/src/pins/mega/pins_INTAMSYS40.h | 99 ++++++++++++++++++++++++++
3 files changed, 109 insertions(+), 11 deletions(-)
diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h
index 9d1f7862bb..f84f42218e 100644
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -1,5 +1,4 @@
-/**
- * Marlin 3D Printer Firmware
+ /** Marlin 3D Printer Firmware
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
@@ -128,7 +127,7 @@
// Choose the name from boards.h that matches your setup
#ifndef MOTHERBOARD
- #define MOTHERBOARD BOARD_RAMPS_14_EFB
+ #define MOTHERBOARD BOARD_INTAMSYS40
#endif
// Name displayed in the LCD "Ready" message and Info menu
@@ -416,7 +415,7 @@
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
*/
-#define TEMP_SENSOR_0 1
+#define TEMP_SENSOR_0 20
#define TEMP_SENSOR_1 0
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
@@ -424,9 +423,9 @@
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_6 0
#define TEMP_SENSOR_7 0
-#define TEMP_SENSOR_BED 0
+#define TEMP_SENSOR_BED 1
#define TEMP_SENSOR_PROBE 0
-#define TEMP_SENSOR_CHAMBER 0
+#define TEMP_SENSOR_CHAMBER 1
// Dummy thermistor constant temperature readings, for use with 998 and 999
#define DUMMY_THERMISTOR_998_VALUE 25
@@ -1698,7 +1697,7 @@
* you must uncomment the following option or it won't work.
*
*/
-//#define SDSUPPORT
+#define SDSUPPORT
/**
* SD CARD: SPI SPEED
@@ -1951,7 +1950,7 @@
// RepRapDiscount FULL GRAPHIC Smart Controller
// https://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
//
-//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
+#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
//
// ReprapWorld Graphical LCD
diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h
index 37c9979771..a0bbc3c84b 100644
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -1370,7 +1370,7 @@
//#define STATUS_ALT_FAN_BITMAP // Use the alternative fan bitmap
//#define STATUS_FAN_FRAMES 3 // :[0,1,2,3,4] Number of fan animation frames
//#define STATUS_HEAT_PERCENT // Show heating in a progress bar
- //#define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash)
+ #define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash)
//#define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~3260 (or ~940) bytes of PROGMEM.
// Frivolous Game Options
@@ -1893,7 +1893,7 @@
* Currently handles M108, M112, M410, M876
* NOTE: Not yet implemented for all platforms.
*/
-//#define EMERGENCY_PARSER
+#define EMERGENCY_PARSER
// Bad Serial-connections can miss a received command by sending an 'ok'
// Therefore some clients abort after 30 seconds in a timeout.
@@ -3505,7 +3505,7 @@
//
// M43 - display pin status, toggle pins, watch pins, watch endstops & toggle LED, test servo probe
//
-//#define PINS_DEBUGGING
+#define PINS_DEBUGGING
// Enable Marlin dev mode which adds some special commands
//#define MARLIN_DEV_MODE
diff --git a/Marlin/src/pins/mega/pins_INTAMSYS40.h b/Marlin/src/pins/mega/pins_INTAMSYS40.h
index 19725eda2f..1e3552d685 100644
--- a/Marlin/src/pins/mega/pins_INTAMSYS40.h
+++ b/Marlin/src/pins/mega/pins_INTAMSYS40.h
@@ -16,18 +16,29 @@
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
+<<<<<<< HEAD
* along with this program. If not, see .
+=======
+ * along with this program. If not, see .
+>>>>>>> Support all but motion
*
*/
#pragma once
/**
+<<<<<<< HEAD
* Intamsys Funmat HT V4.0 Mainboard
* 4988 Drivers Tested
* 2208 version exists and may or may not work
*/
#ifndef __AVR_ATmega2560__
+=======
+ * CNControls V15 for HMS434 pin assignments
+ */
+
+#if !defined(__AVR_ATmega1280__) && !defined(__AVR_ATmega2560__)
+>>>>>>> Support all but motion
#error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'"
#endif
@@ -36,11 +47,16 @@
//
// Servos
//
+<<<<<<< HEAD
#define SERVO0_PIN 12 // Uses High Temp Present Jumper Pin
+=======
+#define SERVO0_PIN -1
+>>>>>>> Support all but motion
//
// Limit Switches
//
+<<<<<<< HEAD
#define X_STOP_PIN 22
#define Y_STOP_PIN 26
#define Z_MIN_PIN 29
@@ -115,10 +131,73 @@
#if ENABLED(PSU_CONTROL)
#define PS_ON_PIN 38 // UPS Module
#endif
+=======
+//
+// Limit Switches
+//
+#define X_MIN_PIN 22
+#define X_MAX_PIN -1
+#define Y_MIN_PIN 26
+#define Y_MAX_PIN -1
+#define Z_MIN_PIN 29
+#define Z_MAX_PIN 69
+
+#ifndef Z_MIN_PROBE_PIN
+ #define Z_MIN_PROBE_PIN -1
+#endif
+
+//
+// Steppers
+//
+#define X_STEP_PIN -1
+#define X_DIR_PIN -1
+#define X_ENABLE_PIN -1//44
+
+#define Y_STEP_PIN -1
+#define Y_DIR_PIN -1
+#define Y_ENABLE_PIN -1//32
+
+#define Z_STEP_PIN -1//45
+#define Z_DIR_PIN -1
+#define Z_ENABLE_PIN -1//34
+
+#define E0_STEP_PIN 69
+#define E0_DIR_PIN 29
+#define E0_ENABLE_PIN 22
+
+//
+// Temperature Sensors
+// Analog Inputs
+//
+#define TEMP_0_PIN 8 // Analog InputD62 A8
+#define TEMP_BED_PIN 10 // Analog Input D64 A10
+
+#define TEMP_CHAMBER_PIN 9 // Analog Input D63
+
+//
+// Heaters
+//
+#define HEATER_0_PIN 2
+#define HEATER_BED_PIN 4
+#define HEATER_CHAMBER_PIN 3
+
+//
+// Fans
+//
+#define FAN_PIN 7
+
+//
+// Misc. Functions
+//
+#define SDSS 53
+#define SD_DETECT_PIN 39
+#define CASE_LIGHT_PIN 8
+>>>>>>> Support all but motion
//
// LCD Controller
//
+<<<<<<< HEAD
#define BEEPER_PIN 18
@@ -150,3 +229,23 @@
Hotend High Temp Connected : D12
*/
+=======
+//#define BEEPER_PIN 18
+
+ #define LCD_PINS_RS 20
+ #define LCD_PINS_ENABLE 30
+ #define LCD_PINS_D4 14
+ #define LCD_PINS_D5 21
+ #define LCD_PINS_D6 5
+ #define LCD_PINS_D7 6
+ #define BTN_EN1 40
+ #define BTN_EN2 41
+ #define BTN_ENC 19
+
+
+// Common I/O
+
+#define FIL_RUNOUT_PIN 10
+//#define BATTERY 38
+#define BEEPER_PIN -1
+>>>>>>> Support all but motion