diff --git a/Marlin/pins_RUMBA.h b/Marlin/pins_RUMBA.h index ffa6a26e47..26d55357b9 100644 --- a/Marlin/pins_RUMBA.h +++ b/Marlin/pins_RUMBA.h @@ -28,27 +28,39 @@ #error "Oops! Make sure you have 'Arduino Mega' selected from the 'Tools -> Boards' menu." #endif -#if HOTENDS > 3 || E_STEPPERS > 3 - #error "RUMBA supports up to 3 hotends / E-steppers. Comment out this line to continue." +#if E_STEPPERS > 3 || HOTENDS > 3 + #error "RUMBA supports up to 3 hotends / E-steppers. Comment this line to keep going." #endif #define DEFAULT_MACHINE_NAME "Rumba" #define BOARD_NAME "Rumba" +//#endif + +#define LARGE_FLASH true // // Servos // -#define SERVO0_PIN 5 +#ifdef IS_RAMPS_13 + #define SERVO0_PIN 7 // RAMPS_13 // Will conflict with BTN_EN2 on LCD_I2C_VIKI +#else + #define SERVO0_PIN 11 +#endif +#define SERVO1_PIN 6 +#define SERVO2_PIN 5 +#define SERVO3_PIN -1 // // Limit Switches // -#define X_MIN_PIN 37 -#define X_MAX_PIN 36 -#define Y_MIN_PIN 35 -#define Y_MAX_PIN 34 -#define Z_MIN_PIN 33 -#define Z_MAX_PIN 32 +#define X_MIN_PIN 3 +#ifndef X_MAX_PIN + #define X_MAX_PIN 2 +#endif +#define Y_MIN_PIN 14 +#define Y_MAX_PIN 15 +#define Z_MIN_PIN 18 +#define Z_MAX_PIN 19 // // Z Probe (when not Z_MIN_PIN) @@ -57,109 +69,255 @@ #define Z_MIN_PROBE_PIN 32 #endif +#define SLED_PIN -1 + // // Steppers // -#define X_STEP_PIN 17 -#define X_DIR_PIN 16 -#define X_ENABLE_PIN 48 +#define X_STEP_PIN 54 +#define X_DIR_PIN 55 +#define X_ENABLE_PIN 38 +#define X_CS_PIN 53 + +#define Y_STEP_PIN 60 +#define Y_DIR_PIN 61 +#define Y_ENABLE_PIN 56 +#define Y_CS_PIN 49 -#define Y_STEP_PIN 54 -#define Y_DIR_PIN 47 -#define Y_ENABLE_PIN 55 - -#define Z_STEP_PIN 57 -#define Z_DIR_PIN 56 +#define Z_STEP_PIN 46 +#define Z_DIR_PIN 48 #define Z_ENABLE_PIN 62 +#define Z_CS_PIN 40 -#define E0_STEP_PIN 23 -#define E0_DIR_PIN 22 +#define E0_STEP_PIN 26 +#define E0_DIR_PIN 28 #define E0_ENABLE_PIN 24 +#define E0_CS_PIN 42 -#define E1_STEP_PIN 26 -#define E1_DIR_PIN 25 -#define E1_ENABLE_PIN 27 +#define E1_STEP_PIN 36 +#define E1_DIR_PIN 34 +#define E1_ENABLE_PIN 30 +#define E1_CS_PIN 44 -#define E2_STEP_PIN 29 -#define E2_DIR_PIN 28 -#define E2_ENABLE_PIN 39 +#define E2_STEP_PIN 42 +#define E2_DIR_PIN 43 +#define E2_ENABLE_PIN 44 // // Temperature Sensors // -#if TEMP_SENSOR_0 == -1 - #define TEMP_0_PIN 6 // Analog Input (connector *K1* on RUMBA thermocouple ADD ON is used) +#define TEMP_0_PIN 13 // Analog Input +#define TEMP_1_PIN 15 // Analog Input +#define TEMP_BED_PIN 14 // Analog Input + +// SPI for Max6675 or Max31855 Thermocouple +#if DISABLED(SDSUPPORT) + #define MAX6675_SS 66 // Do not use pin 53 if there is even the remote possibility of using Display/SD card #else - #define TEMP_0_PIN 15 // Analog Input (default connector for thermistor *T0* on rumba board is used) + #define MAX6675_SS 66 // Do not use pin 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present #endif -#if TEMP_SENSOR_1 == -1 - #define TEMP_1_PIN 5 // Analog Input (connector *K2* on RUMBA thermocouple ADD ON is used) -#else - #define TEMP_1_PIN 14 // Analog Input (default connector for thermistor *T1* on rumba board is used) -#endif - -#if TEMP_SENSOR_2 == -1 - #define TEMP_2_PIN 7 // Analog Input (connector *K3* on RUMBA thermocouple ADD ON is used <-- this can't be used when TEMP_SENSOR_BED is defined as thermocouple) -#else - #define TEMP_2_PIN 13 // Analog Input (default connector for thermistor *T2* on rumba board is used) -#endif - -// optional for extruder 4 or chamber: -//#define TEMP_X_PIN 12 // Analog Input (default connector for thermistor *T3* on rumba board is used) -//#define TEMP_CHAMBER_PIN 12 // Analog Input (default connector for thermistor *T3* on rumba board is used) - -#if TEMP_SENSOR_BED == -1 - #define TEMP_BED_PIN 7 // Analog Input (connector *K3* on RUMBA thermocouple ADD ON is used <-- this can't be used when TEMP_SENSOR_2 is defined as thermocouple) -#else - #define TEMP_BED_PIN 11 // Analog Input (default connector for thermistor *THB* on rumba board is used) +// +// Augmentation for auto-assigning RAMPS plugs +// +#if DISABLED(IS_RAMPS_EEB) && DISABLED(IS_RAMPS_EEF) && DISABLED(IS_RAMPS_EFB) && DISABLED(IS_RAMPS_EFF) && DISABLED(IS_RAMPS_SF) && !PIN_EXISTS(MOSFET_D) + #if HOTENDS > 1 + #if TEMP_SENSOR_BED + #define IS_RAMPS_EEB + #else + #define IS_RAMPS_EEF + #endif + #elif TEMP_SENSOR_BED + #define IS_RAMPS_EFB + #else + #define IS_RAMPS_EFF + #endif #endif // // Heaters / Fans // -#define HEATER_0_PIN 2 -#define HEATER_1_PIN 3 -#define HEATER_2_PIN 6 -#define HEATER_3_PIN 8 -#define HEATER_BED_PIN 9 +#define HEATER_0_PIN 10 +#define HEATER_1_PIN 58 +//#define HEATER_2_PIN 6 +//#define HEATER_3_PIN 8 +#define HEATER_BED_PIN 8 -#define FAN_PIN 7 -#define FAN1_PIN 8 +#define LED4_PIN 5 +#define LASER_PIN -1 + +#define FAN_PIN 9 +#define FAN1_PIN -1 // // Misc. Functions // #define SDSS 53 #define LED_PIN 13 -#define PS_ON_PIN 45 -#define KILL_PIN 46 -#define CASE_LIGHT_PIN 45 + +// Use the RAMPS 1.4 Analog input 5 on the AUX2 connector +#define FILWIDTH_PIN 5 // Analog Input + +// define digital pin 4 for the filament runout sensor. Use the RAMPS 1.4 digital input 4 on the servos connector +//#define FIL_RUNOUT_PIN 4 + +#define PS_ON_PIN 12 // // LCD / Controller // -#define SD_DETECT_PIN 49 -#define BEEPER_PIN 44 -#define LCD_PINS_RS 19 -#define LCD_PINS_ENABLE 42 -#define LCD_PINS_D4 18 -#define LCD_PINS_D5 38 -#define LCD_PINS_D6 41 -#define LCD_PINS_D7 40 -#define BTN_EN1 11 -#define BTN_EN2 12 -#define BTN_ENC 43 +#if ENABLED(ULTRA_LCD) + + #if ENABLED(REPRAPWORLD_GRAPHICAL_LCD) + #define LCD_PINS_RS 49 // CS chip select /SS chip slave select + #define LCD_PINS_ENABLE 51 // SID (MOSI) + #define LCD_PINS_D4 52 // SCK (CLK) clock + #elif ENABLED(NEWPANEL) && ENABLED(PANEL_ONE) + #define LCD_PINS_RS 40 + #define LCD_PINS_ENABLE 42 + #define LCD_PINS_D4 65 + #define LCD_PINS_D5 66 + #define LCD_PINS_D6 44 + #define LCD_PINS_D7 64 + #else + #define LCD_PINS_RS 16 + #define LCD_PINS_ENABLE 17 + #define LCD_PINS_D4 23 + #define LCD_PINS_D5 25 + #define LCD_PINS_D6 27 + #define LCD_PINS_D7 29 + #if DISABLED(NEWPANEL) + #define BEEPER_PIN 33 + // Buttons are attached to a shift register + // Not wired yet + //#define SHIFT_CLK 38 + //#define SHIFT_LD 42 + //#define SHIFT_OUT 40 + //#define SHIFT_EN 17 + #endif + #endif + + #if ENABLED(NEWPANEL) + + #if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) + #define BEEPER_PIN 37 + + #define BTN_EN1 31 + #define BTN_EN2 33 + #define BTN_ENC 35 + + #define SD_DETECT_PIN 49 + #define KILL_PIN 41 + + #if ENABLED(BQ_LCD_SMART_CONTROLLER) + #define LCD_BACKLIGHT_PIN 39 + #endif + + #elif ENABLED(REPRAPWORLD_GRAPHICAL_LCD) + #define BTN_EN1 64 + #define BTN_EN2 59 + #define BTN_ENC 63 + #define SD_DETECT_PIN 42 + #elif ENABLED(LCD_I2C_PANELOLU2) + #define BTN_EN1 47 // reverse if the encoder turns the wrong way. + #define BTN_EN2 43 + #define BTN_ENC 32 + #define LCD_SDSS 53 + #define SD_DETECT_PIN -1 + #define KILL_PIN 41 + #elif ENABLED(LCD_I2C_VIKI) + #define BTN_EN1 22 // reverse if the encoder turns the wrong way. + #define BTN_EN2 7 // http://files.panucatt.com/datasheets/viki_wiring_diagram.pdf + // tells about 40/42. + // 22/7 are unused on RAMPS_14. 22 is unused and 7 the SERVO0_PIN on RAMPS_13. + #define BTN_ENC -1 + #define LCD_SDSS 53 + #define SD_DETECT_PIN 49 + #elif ENABLED(VIKI2) || ENABLED(miniVIKI) + #define BEEPER_PIN 33 + + // Pins for DOGM SPI LCD Support + #define DOGLCD_A0 44 + #define DOGLCD_CS 45 + #define LCD_SCREEN_ROT_180 + + #define BTN_EN1 22 + #define BTN_EN2 7 + #define BTN_ENC 39 + + #define SDSS 53 + #define SD_DETECT_PIN -1 // Pin 49 for display sd interface, 72 for easy adapter board + + #define KILL_PIN 31 + + #define STAT_LED_RED_PIN 32 + #define STAT_LED_BLUE_PIN 35 + + #elif ENABLED(ELB_FULL_GRAPHIC_CONTROLLER) + #define BTN_EN1 35 // reverse if the encoder turns the wrong way. + #define BTN_EN2 37 + #define BTN_ENC 31 + #define SD_DETECT_PIN 49 + #define LCD_SDSS 53 + #define KILL_PIN 41 + #define BEEPER_PIN 23 + #define DOGLCD_CS 29 + #define DOGLCD_A0 27 + #define LCD_BACKLIGHT_PIN 33 + #elif ENABLED(MINIPANEL) + #define BEEPER_PIN 42 + // Pins for DOGM SPI LCD Support + #define DOGLCD_A0 44 + #define DOGLCD_CS 66 + #define LCD_BACKLIGHT_PIN 65 // backlight LED on A11/D65 + #define SDSS 53 + + #define KILL_PIN 64 + // GLCD features + //#define LCD_CONTRAST 190 + // Uncomment screen orientation + //#define LCD_SCREEN_ROT_90 + //#define LCD_SCREEN_ROT_180 + //#define LCD_SCREEN_ROT_270 + // The encoder and click button + #define BTN_EN1 40 + #define BTN_EN2 63 + #define BTN_ENC 59 + // not connected to a pin + #define SD_DETECT_PIN 49 + + #else + + // Beeper on AUX-4 + #define BEEPER_PIN 33 + + // buttons are directly attached using AUX-2 + #if ENABLED(REPRAPWORLD_KEYPAD) + #define BTN_EN1 64 // encoder + #define BTN_EN2 59 // encoder + #define BTN_ENC 63 // enter button + #define SHIFT_OUT 40 // shift register + #define SHIFT_CLK 44 // shift register + #define SHIFT_LD 42 // shift register + #elif ENABLED(PANEL_ONE) + #define BTN_EN1 59 // AUX2 PIN 3 + #define BTN_EN2 63 // AUX2 PIN 4 + #define BTN_ENC 49 // AUX3 PIN 7 + #else + #define BTN_EN1 37 + #define BTN_EN2 35 + #define BTN_ENC 31 // the click + #endif + + #if ENABLED(G3D_PANEL) + #define SD_DETECT_PIN 49 + #define KILL_PIN 41 + #else + //#define SD_DETECT_PIN -1 // Ramps doesn't use this + #endif + + #endif + #endif // NEWPANEL + +#endif // ULTRA_LCD -// -// M3/M4/M5 - Spindle/Laser Control -// -#ifndef SPINDLE_LASER_PWM_PIN - #define SPINDLE_LASER_PWM_PIN 4 // MUST BE HARDWARE PWM. Pin 4 interrupts OC0* and OC1* always in use? -#endif -#ifndef SPINDLE_LASER_ENABLE_PIN - #define SPINDLE_LASER_ENABLE_PIN 14 // Pin should have a pullup! -#endif -#ifndef SPINDLE_DIR_PIN - #define SPINDLE_DIR_PIN 15 -#endif