diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index 1098351d4e..ce847c0d65 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -2181,6 +2181,11 @@ // //#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER +// +// K.3D Full Graphic Smart Controller +// +//#define K3D_FULL_GRAPHIC_SMART_CONTROLLER + // // ReprapWorld Graphical LCD // https://reprapworld.com/?products_details&products_id/1218 @@ -2318,7 +2323,7 @@ //#define OLED_PANEL_TINYBOY2 // -// MKS OLED 1.3" 128×64 FULL GRAPHICS CONTROLLER +// MKS OLED 1.3" 128×64 Full Graphics Controller // https://reprap.org/wiki/MKS_12864OLED // // Tiny, but very sharp OLED display @@ -2327,7 +2332,7 @@ //#define MKS_12864OLED_SSD1306 // Uses the SSD1306 controller // -// Zonestar OLED 128×64 FULL GRAPHICS CONTROLLER +// Zonestar OLED 128×64 Full Graphics Controller // //#define ZONESTAR_12864LCD // Graphical (DOGM) with ST7920 controller //#define ZONESTAR_12864OLED // 1.3" OLED with SH1106 controller (default) @@ -2344,10 +2349,15 @@ //#define OVERLORD_OLED // -// FYSETC OLED 2.42" 128×64 FULL GRAPHICS CONTROLLER with WS2812 RGB +// FYSETC OLED 2.42" 128×64 Full Graphics Controller with WS2812 RGB // Where to find : https://www.aliexpress.com/item/4000345255731.html //#define FYSETC_242_OLED_12864 // Uses the SSD1309 controller +// +// K.3D SSD1309 OLED 2.42" 128×64 Full Graphics Controller +// +//#define K3D_242_OLED_CONTROLLER // Software SPI + //============================================================================= //========================== Extensible UI Displays =========================== //============================================================================= @@ -2386,6 +2396,14 @@ //#define ANYCUBIC_LCD_DEBUG #endif +// +// 320x240 Nextion 2.8" serial TFT Resistive Touch Screen NX3224T028 +// +//#define NEXTION_TFT +#if ENABLED(NEXTION_TFT) + #define LCD_SERIAL_PORT 1 // Default is 1 for Nextion +#endif + // // Third-party or vendor-customized controller interfaces. // Sources should be installed in 'src/lcd/extui'. diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h index 9ab3e2d044..fb1f79b230 100644 --- a/Marlin/Configuration_adv.h +++ b/Marlin/Configuration_adv.h @@ -3455,22 +3455,28 @@ //#define CUSTOM_USER_MENU_TITLE "Custom Commands" #define USER_SCRIPT_DONE "M117 User Script Done" #define USER_SCRIPT_AUDIBLE_FEEDBACK - //#define USER_SCRIPT_RETURN // Return to status screen after a script + //#define USER_SCRIPT_RETURN // Return to status screen after a script + #define CUSTOM_MENU_ONLY_IDLE // Only show custom menu when the machine is idle #define USER_DESC_1 "Home & UBL Info" #define USER_GCODE_1 "G28\nG29W" + //#define USER_CONFIRM_1 // Show a confirmation dialog before this action #define USER_DESC_2 "Preheat for " PREHEAT_1_LABEL #define USER_GCODE_2 "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND) + //#define USER_CONFIRM_2 #define USER_DESC_3 "Preheat for " PREHEAT_2_LABEL #define USER_GCODE_3 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND) + //#define USER_CONFIRM_3 #define USER_DESC_4 "Heat Bed/Home/Level" #define USER_GCODE_4 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29" + //#define USER_CONFIRM_4 #define USER_DESC_5 "Home & Info" #define USER_GCODE_5 "G28\nM503" + //#define USER_CONFIRM_5 #endif /** diff --git a/Marlin/src/HAL/HAL.h b/Marlin/src/HAL/HAL.h index 9eefda8fb1..0cd836af2b 100644 --- a/Marlin/src/HAL/HAL.h +++ b/Marlin/src/HAL/HAL.h @@ -29,12 +29,6 @@ #include HAL_PATH(.,HAL.h) -#ifdef SERIAL_PORT_2 - #define NUM_SERIAL 2 -#else - #define NUM_SERIAL 1 -#endif - #define HAL_ADC_RANGE _BV(HAL_ADC_RESOLUTION) #ifndef I2C_ADDRESS diff --git a/Marlin/src/HAL/STM32F1/eeprom_if_iic.cpp b/Marlin/src/HAL/STM32F1/eeprom_if_iic.cpp index ccc3fc537f..78b7af0b04 100644 --- a/Marlin/src/HAL/STM32F1/eeprom_if_iic.cpp +++ b/Marlin/src/HAL/STM32F1/eeprom_if_iic.cpp @@ -40,7 +40,7 @@ void eeprom_init() { BL24CXX::init(); } // Public functions // ------------------------ -void eeprom_write_byte(uint8_t *pos, unsigned char value) { +void eeprom_write_byte(uint8_t *pos, uint8_t value) { const unsigned eeprom_address = (unsigned)pos; return BL24CXX::writeOneByte(eeprom_address, value); } diff --git a/Marlin/src/HAL/TEENSY31_32/HAL.cpp b/Marlin/src/HAL/TEENSY31_32/HAL.cpp index 8a13f1d884..7b7202547a 100644 --- a/Marlin/src/HAL/TEENSY31_32/HAL.cpp +++ b/Marlin/src/HAL/TEENSY31_32/HAL.cpp @@ -31,7 +31,11 @@ #include -DefaultSerial1 MSerial0(false); +#define _IMPLEMENT_SERIAL(X) DefaultSerial##X MSerial##X(false, Serial##X) +#define IMPLEMENT_SERIAL(X) _IMPLEMENT_SERIAL(X) +#if WITHIN(SERIAL_PORT, 0, 3) + IMPLEMENT_SERIAL(SERIAL_PORT); +#endif USBSerialType USBSerial(false, SerialUSB); uint16_t HAL_adc_result; diff --git a/Marlin/src/HAL/TEENSY31_32/HAL.h b/Marlin/src/HAL/TEENSY31_32/HAL.h index cd1c334899..bbfc50a36f 100644 --- a/Marlin/src/HAL/TEENSY31_32/HAL.h +++ b/Marlin/src/HAL/TEENSY31_32/HAL.h @@ -51,8 +51,13 @@ #endif #include "../../core/serial_hook.h" -typedef Serial1Class DefaultSerial1; -extern DefaultSerial1 MSerial0; + +#define Serial0 Serial +#define _DECLARE_SERIAL(X) \ + typedef ForwardSerial1Class DefaultSerial##X; \ + extern DefaultSerial##X MSerial##X +#define DECLARE_SERIAL(X) _DECLARE_SERIAL(X) + typedef ForwardSerial1Class USBSerialType; extern USBSerialType USBSerial; @@ -62,6 +67,7 @@ extern USBSerialType USBSerial; #if SERIAL_PORT == -1 #define MYSERIAL1 USBSerial #elif WITHIN(SERIAL_PORT, 0, 3) + DECLARE_SERIAL(SERIAL_PORT); #define MYSERIAL1 MSERIAL(SERIAL_PORT) #endif diff --git a/Marlin/src/HAL/TEENSY35_36/HAL.cpp b/Marlin/src/HAL/TEENSY35_36/HAL.cpp index 8640bdfe00..5d808cd19b 100644 --- a/Marlin/src/HAL/TEENSY35_36/HAL.cpp +++ b/Marlin/src/HAL/TEENSY35_36/HAL.cpp @@ -31,7 +31,7 @@ #include -#define _IMPLEMENT_SERIAL(X) DefaultSerial##X MSerial##X(false) +#define _IMPLEMENT_SERIAL(X) DefaultSerial##X MSerial##X(false, Serial##X) #define IMPLEMENT_SERIAL(X) _IMPLEMENT_SERIAL(X) #if WITHIN(SERIAL_PORT, 0, 3) IMPLEMENT_SERIAL(SERIAL_PORT); diff --git a/Marlin/src/HAL/TEENSY35_36/HAL.h b/Marlin/src/HAL/TEENSY35_36/HAL.h index e769454b3f..5b120d852d 100644 --- a/Marlin/src/HAL/TEENSY35_36/HAL.h +++ b/Marlin/src/HAL/TEENSY35_36/HAL.h @@ -57,7 +57,7 @@ #define Serial0 Serial #define _DECLARE_SERIAL(X) \ - typedef Serial1Class DefaultSerial##X; \ + typedef ForwardSerial1Class DefaultSerial##X; \ extern DefaultSerial##X MSerial##X #define DECLARE_SERIAL(X) _DECLARE_SERIAL(X) diff --git a/Marlin/src/HAL/TEENSY40_41/HAL.cpp b/Marlin/src/HAL/TEENSY40_41/HAL.cpp index 0fde9da537..1eab3d837e 100644 --- a/Marlin/src/HAL/TEENSY40_41/HAL.cpp +++ b/Marlin/src/HAL/TEENSY40_41/HAL.cpp @@ -32,7 +32,11 @@ #include -DefaultSerial1 MSerial0(false); +#define _IMPLEMENT_SERIAL(X) DefaultSerial##X MSerial##X(false, Serial##X) +#define IMPLEMENT_SERIAL(X) _IMPLEMENT_SERIAL(X) +#if WITHIN(SERIAL_PORT, 0, 3) + IMPLEMENT_SERIAL(SERIAL_PORT); +#endif USBSerialType USBSerial(false, SerialUSB); uint16_t HAL_adc_result, HAL_adc_select; diff --git a/Marlin/src/HAL/TEENSY40_41/HAL.h b/Marlin/src/HAL/TEENSY40_41/HAL.h index 03a12e1b92..ce985dadb9 100644 --- a/Marlin/src/HAL/TEENSY40_41/HAL.h +++ b/Marlin/src/HAL/TEENSY40_41/HAL.h @@ -56,8 +56,12 @@ #endif #include "../../core/serial_hook.h" -typedef Serial1Class DefaultSerial1; -extern DefaultSerial1 MSerial0; +#define Serial0 Serial +#define _DECLARE_SERIAL(X) \ + typedef ForwardSerial1Class DefaultSerial##X; \ + extern DefaultSerial##X MSerial##X +#define DECLARE_SERIAL(X) _DECLARE_SERIAL(X) + typedef ForwardSerial1Class USBSerialType; extern USBSerialType USBSerial; @@ -67,6 +71,7 @@ extern USBSerialType USBSerial; #if SERIAL_PORT == -1 #define MYSERIAL1 SerialUSB #elif WITHIN(SERIAL_PORT, 0, 8) + DECLARE_SERIAL(SERIAL_PORT); #define MYSERIAL1 MSERIAL(SERIAL_PORT) #else #error "The required SERIAL_PORT must be from -1 to 8. Please update your configuration." diff --git a/Marlin/src/HAL/shared/eeprom_if.h b/Marlin/src/HAL/shared/eeprom_if.h index e44da801df..e496de2a03 100644 --- a/Marlin/src/HAL/shared/eeprom_if.h +++ b/Marlin/src/HAL/shared/eeprom_if.h @@ -25,5 +25,5 @@ // EEPROM // void eeprom_init(); -void eeprom_write_byte(uint8_t *pos, unsigned char value); +void eeprom_write_byte(uint8_t *pos, uint8_t value); uint8_t eeprom_read_byte(uint8_t *pos); diff --git a/Marlin/src/HAL/shared/eeprom_if_i2c.cpp b/Marlin/src/HAL/shared/eeprom_if_i2c.cpp index da70af2772..f6dd33b7c4 100644 --- a/Marlin/src/HAL/shared/eeprom_if_i2c.cpp +++ b/Marlin/src/HAL/shared/eeprom_if_i2c.cpp @@ -55,12 +55,15 @@ static constexpr uint8_t eeprom_device_address = I2C_ADDRESS(EEPROM_DEVICE_ADDRE // Public functions // ------------------------ -void eeprom_write_byte(uint8_t *pos, unsigned char value) { +static void _eeprom_begin(uint8_t * const pos) { const unsigned eeprom_address = (unsigned)pos; - Wire.beginTransmission(eeprom_device_address); - Wire.write(int(eeprom_address >> 8)); // MSB - Wire.write(int(eeprom_address & 0xFF)); // LSB + Wire.write(int(eeprom_address >> 8)); // Address High + Wire.write(int(eeprom_address & 0xFF)); // Address Low +} + +void eeprom_write_byte(uint8_t *pos, uint8_t value) { + _eeprom_begin(pos); Wire.write(value); Wire.endTransmission(); @@ -70,11 +73,7 @@ void eeprom_write_byte(uint8_t *pos, unsigned char value) { } uint8_t eeprom_read_byte(uint8_t *pos) { - const unsigned eeprom_address = (unsigned)pos; - - Wire.beginTransmission(eeprom_device_address); - Wire.write(int(eeprom_address >> 8)); // MSB - Wire.write(int(eeprom_address & 0xFF)); // LSB + _eeprom_begin(pos); Wire.endTransmission(); Wire.requestFrom(eeprom_device_address, (byte)1); return Wire.available() ? Wire.read() : 0xFF; diff --git a/Marlin/src/HAL/shared/eeprom_if_spi.cpp b/Marlin/src/HAL/shared/eeprom_if_spi.cpp index a341fef9de..e162f6fedc 100644 --- a/Marlin/src/HAL/shared/eeprom_if_spi.cpp +++ b/Marlin/src/HAL/shared/eeprom_if_spi.cpp @@ -43,44 +43,41 @@ void eeprom_init() {} #define EEPROM_WRITE_DELAY 7 #endif -uint8_t eeprom_read_byte(uint8_t* pos) { - uint8_t v; - uint8_t eeprom_temp[3]; - - // set read location - // begin transmission from device - eeprom_temp[0] = CMD_READ; - eeprom_temp[1] = ((unsigned)pos>>8) & 0xFF; // addr High - eeprom_temp[2] = (unsigned)pos& 0xFF; // addr Low - WRITE(SPI_EEPROM1_CS, HIGH); - WRITE(SPI_EEPROM1_CS, LOW); +static void _eeprom_begin(uint8_t * const pos, const uint8_t cmd) { + const uint8_t eeprom_temp[3] = { + cmd, + (unsigned(pos) >> 8) & 0xFF, // Address High + unsigned(pos) & 0xFF // Address Low + }; + WRITE(SPI_EEPROM1_CS, HIGH); // Usually free already + WRITE(SPI_EEPROM1_CS, LOW); // Activate the Bus spiSend(SPI_CHAN_EEPROM1, eeprom_temp, 3); + // Leave the Bus in-use +} + +uint8_t eeprom_read_byte(uint8_t* pos) { + _eeprom_begin(pos, CMD_READ); // Set read location and begin transmission + + const uint8_t v = spiRec(SPI_CHAN_EEPROM1); // After READ a value sits on the Bus + + WRITE(SPI_EEPROM1_CS, HIGH); // Done with device - v = spiRec(SPI_CHAN_EEPROM1); - WRITE(SPI_EEPROM1_CS, HIGH); return v; } -void eeprom_write_byte(uint8_t* pos, uint8_t value) { - uint8_t eeprom_temp[3]; - - /*write enable*/ - eeprom_temp[0] = CMD_WREN; +void eeprom_write_byte(uint8_t *pos, uint8_t value) { + const uint8_t eeprom_temp = CMD_WREN; WRITE(SPI_EEPROM1_CS, LOW); - spiSend(SPI_CHAN_EEPROM1, eeprom_temp, 1); - WRITE(SPI_EEPROM1_CS, HIGH); - delay(1); + spiSend(SPI_CHAN_EEPROM1, &eeprom_temp, 1); // Write Enable - /*write addr*/ - eeprom_temp[0] = CMD_WRITE; - eeprom_temp[1] = ((unsigned)pos>>8) & 0xFF; //addr High - eeprom_temp[2] = (unsigned)pos & 0xFF; //addr Low - WRITE(SPI_EEPROM1_CS, LOW); - spiSend(SPI_CHAN_EEPROM1, eeprom_temp, 3); + WRITE(SPI_EEPROM1_CS, HIGH); // Done with the Bus + delay(1); // For a small amount of time - spiSend(SPI_CHAN_EEPROM1, value); - WRITE(SPI_EEPROM1_CS, HIGH); - delay(EEPROM_WRITE_DELAY); // wait for page write to complete + _eeprom_begin(pos, CMD_WRITE); // Set write address and begin transmission + + spiSend(SPI_CHAN_EEPROM1, value); // Send the value to be written + WRITE(SPI_EEPROM1_CS, HIGH); // Done with the Bus + delay(EEPROM_WRITE_DELAY); // Give page write time to complete } #endif // USE_SHARED_EEPROM diff --git a/Marlin/src/MarlinCore.cpp b/Marlin/src/MarlinCore.cpp index e1756af511..26ca8305f4 100644 --- a/Marlin/src/MarlinCore.cpp +++ b/Marlin/src/MarlinCore.cpp @@ -889,8 +889,8 @@ void stop() { print_job_timer.stop(); - #if ENABLED(PROBING_FANS_OFF) - if (thermalManager.fans_paused) thermalManager.set_fans_paused(false); // put things back the way they were + #if EITHER(PROBING_FANS_OFF, ADVANCED_PAUSE_FANS_PAUSE) + thermalManager.set_fans_paused(false); // Un-pause fans for safety #endif if (IsRunning()) { @@ -953,23 +953,92 @@ inline void tmc_standby_setup() { } /** - * Marlin entry-point: Set up before the program loop - * - Set up the kill pin, filament runout, power hold, custom user buttons - * - Start the serial port + * Marlin Firmware entry-point. Abandon Hope All Ye Who Enter Here. + * Setup before the program loop: + * + * - Call any special pre-init set for the board + * - Put TMC drivers into Low Power Standby mode + * - Init the serial ports (so setup can be debugged) + * - Set up the kill and suicide pins + * - Prepare (disable) board JTAG and Debug ports + * - Init serial for a connected MKS TFT with WiFi + * - Install Marlin custom Exception Handlers, if set. + * - Init Marlin's HAL interfaces (for SPI, i2c, etc.) + * - Init some optional hardware and features: + * • MAX Thermocouple pins + * • Duet Smart Effector + * • Filament Runout Sensor + * • TMC220x Stepper Drivers (Serial) + * • PSU control + * • Power-loss Recovery + * • L64XX Stepper Drivers (SPI) + * • Stepper Driver Reset: DISABLE + * • TMC Stepper Drivers (SPI) + * • Run BOARD_INIT if defined + * • ESP WiFi + * - Get the Reset Reason and report it * - Print startup messages and diagnostics - * - Get EEPROM or default settings - * - Initialize managers for: - * • temperature - * • planner - * • watchdog - * • stepper - * • photo pin - * • servos - * • LCD controller - * • Digipot I2C - * • Z probe sled - * • status LEDs - * • Max7219 + * - Calibrate the HAL DELAY for precise timing + * - Init the buzzer, possibly a custom timer + * - Init more optional hardware: + * • Color LED illumination + * • Neopixel illumination + * • Controller Fan + * • Creality DWIN LCD (show boot image) + * • Tare the Probe if possible + * - Mount the (most likely external) SD Card + * - Load settings from EEPROM (or use defaults) + * - Init the Ethernet Port + * - Init Touch Buttons (for emulated DOGLCD) + * - Adjust the (certainly wrong) current position by the home offset + * - Init the Planner::position (steps) based on current (native) position + * - Initialize more managers and peripherals: + * • Temperatures + * • Print Job Timer + * • Endstops and Endstop Interrupts + * • Stepper ISR - Kind of Important! + * • Servos + * • Servo-based Probe + * • Photograph Pin + * • Laser/Spindle tool Power / PWM + * • Coolant Control + * • Bed Probe + * • Stepper Driver Reset: ENABLE + * • Digipot I2C - Stepper driver current control + * • Stepper DAC - Stepper driver current control + * • Solenoid (probe, or for other use) + * • Home Pin + * • Custom User Buttons + * • Red/Blue Status LEDs + * • Case Light + * • Prusa MMU filament changer + * • Fan Multiplexer + * • Mixing Extruder + * • BLTouch Probe + * • I2C Position Encoders + * • Custom I2C Bus handlers + * • Enhanced tools or extruders: + * • Switching Extruder + * • Switching Nozzle + * • Parking Extruder + * • Magnetic Parking Extruder + * • Switching Toolhead + * • Electromagnetic Switching Toolhead + * • Watchdog Timer - Also Kind of Important! + * • Closed Loop Controller + * - Run Startup Commands, if defined + * - Tell host to close Host Prompts + * - Test Trinamic driver connections + * - Init Prusa MMU2 filament changer + * - Init and test BL24Cxx EEPROM + * - Init Creality DWIN encoder, show faux progress bar + * - Reset Status Message / Show Service Messages + * - Init MAX7219 LED Matrix + * - Init Direct Stepping (Klipper-style motion control) + * - Init TFT LVGL UI (with 3D Graphics) + * - Apply Password Lock - Hold for Authentication + * - Open Touch Screen Calibration screen, if not calibrated + * - Set Marlin to RUNNING State */ void setup() { #ifdef BOARD_PREINIT @@ -1311,7 +1380,6 @@ void setup() { #if PIN_EXISTS(STAT_LED_RED) OUT_WRITE(STAT_LED_RED_PIN, LOW); // OFF #endif - #if PIN_EXISTS(STAT_LED_BLUE) OUT_WRITE(STAT_LED_BLUE_PIN, LOW); // OFF #endif @@ -1364,19 +1432,13 @@ void setup() { #endif #endif - #if ENABLED(MAGNETIC_PARKING_EXTRUDER) - SETUP_RUN(mpe_settings_init()); - #endif - #if ENABLED(PARKING_EXTRUDER) SETUP_RUN(pe_solenoid_init()); - #endif - - #if ENABLED(SWITCHING_TOOLHEAD) + #elif ENABLED(MAGNETIC_PARKING_EXTRUDER) + SETUP_RUN(mpe_settings_init()); + #elif ENABLED(SWITCHING_TOOLHEAD) SETUP_RUN(swt_init()); - #endif - - #if ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) + #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD) SETUP_RUN(est_init()); #endif diff --git a/Marlin/src/core/boards.h b/Marlin/src/core/boards.h index cfde52ddb9..f0d967c763 100644 --- a/Marlin/src/core/boards.h +++ b/Marlin/src/core/boards.h @@ -279,6 +279,7 @@ #define BOARD_ARCHIM2 3024 // UltiMachine Archim2 (with TMC2130 drivers) #define BOARD_ALLIGATOR 3025 // Alligator Board R2 #define BOARD_CNCONTROLS_15D 3026 // Cartesio CN Controls V15 on DUE +#define BOARD_KRATOS32 3027 // K.3D Kratos32 (Arduino Due Shield) // // SAM3X8C ARM Cortex M3 diff --git a/Marlin/src/feature/encoder_i2c.cpp b/Marlin/src/feature/encoder_i2c.cpp index cf5ebfd012..abaa93f767 100644 --- a/Marlin/src/feature/encoder_i2c.cpp +++ b/Marlin/src/feature/encoder_i2c.cpp @@ -47,7 +47,7 @@ void I2CPositionEncoder::init(const uint8_t address, const AxisEnum axis) { encoderAxis = axis; i2cAddress = address; - initialized++; + initialized = true; SERIAL_ECHOLNPAIR("Setting up encoder on ", AS_CHAR(axis_codes[encoderAxis]), " axis, addr = ", address); @@ -209,8 +209,7 @@ void I2CPositionEncoder::set_homed() { delay(10); zeroOffset = get_raw_count(); - homed++; - trusted++; + homed = trusted = true; #ifdef I2CPE_DEBUG SERIAL_CHAR(axis_codes[encoderAxis]); diff --git a/Marlin/src/feature/meatpack.cpp b/Marlin/src/feature/meatpack.cpp index 178831c9bb..44567ac482 100644 --- a/Marlin/src/feature/meatpack.cpp +++ b/Marlin/src/feature/meatpack.cpp @@ -42,7 +42,6 @@ #if HAS_MEATPACK #include "meatpack.h" -MeatPack meatpack; #define MeatPack_ProtocolVersion "PV01" //#define MP_DEBUG diff --git a/Marlin/src/inc/Conditionals_LCD.h b/Marlin/src/inc/Conditionals_LCD.h index e5f7441e77..fc83a1ff87 100644 --- a/Marlin/src/inc/Conditionals_LCD.h +++ b/Marlin/src/inc/Conditionals_LCD.h @@ -229,14 +229,18 @@ #define BOARD_ST7920_DELAY_2 DELAY_NS(125) #define BOARD_ST7920_DELAY_3 DELAY_NS(125) -#elif ANY(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER, ANET_FULL_GRAPHICS_LCD, ANET_FULL_GRAPHICS_LCD_ALT_WIRING, BQ_LCD_SMART_CONTROLLER) +#elif ANY(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER, ANET_FULL_GRAPHICS_LCD, ANET_FULL_GRAPHICS_LCD_ALT_WIRING, BQ_LCD_SMART_CONTROLLER, K3D_FULL_GRAPHIC_SMART_CONTROLLER) #define IS_RRD_FG_SC 1 #elif ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER) - // RepRapDiscount LCD or Graphical LCD with rotary click encoder + #define IS_RRD_SC 1 // RepRapDiscount LCD or Graphical LCD with rotary click encoder + +#elif ENABLED(K3D_242_OLED_CONTROLLER) + #define IS_RRD_SC 1 + #define U8GLIB_SSD1309 #endif @@ -456,7 +460,7 @@ #endif // Extensible UI serial touch screens. (See src/lcd/extui) -#if ANY(HAS_DGUS_LCD, MALYAN_LCD, TOUCH_UI_FTDI_EVE, ANYCUBIC_LCD_I3MEGA, ANYCUBIC_LCD_CHIRON) +#if ANY(HAS_DGUS_LCD, MALYAN_LCD, TOUCH_UI_FTDI_EVE, ANYCUBIC_LCD_I3MEGA, ANYCUBIC_LCD_CHIRON, NEXTION_TFT) #define IS_EXTUI 1 #define EXTENSIBLE_UI #endif @@ -654,13 +658,6 @@ #define UNUSED_E(E) UNUSED(E) #endif -#if ENABLED(DWIN_CREALITY_LCD) - #define SERIAL_CATCHALL 0 - #ifndef LCD_SERIAL_PORT - #define LCD_SERIAL_PORT 3 // Creality 4.x board - #endif -#endif - /** * The BLTouch Probe emulates a servo probe * and uses "special" angles for its state. @@ -950,6 +947,18 @@ #define HAS_CLASSIC_E_JERK 1 #endif +// +// Serial Port Info +// +#ifdef SERIAL_PORT_2 + #define NUM_SERIAL 2 + #define HAS_MULTI_SERIAL 1 +#elif defined(SERIAL_PORT) + #define NUM_SERIAL 1 +#else + #define NUM_SERIAL 0 + #undef BAUD_RATE_GCODE +#endif #if SERIAL_PORT == -1 || SERIAL_PORT_2 == -1 #define HAS_USB_SERIAL 1 #endif @@ -957,6 +966,13 @@ #define HAS_ETHERNET 1 #endif +#if ENABLED(DWIN_CREALITY_LCD) + #define SERIAL_CATCHALL 0 + #ifndef LCD_SERIAL_PORT + #define LCD_SERIAL_PORT 3 // Creality 4.x board + #endif +#endif + // Fallback Stepper Driver types that don't depend on Configuration_adv.h #ifndef X_DRIVER_TYPE #define X_DRIVER_TYPE A4988 diff --git a/Marlin/src/inc/Conditionals_adv.h b/Marlin/src/inc/Conditionals_adv.h index 00b9b1faef..490766bd7a 100644 --- a/Marlin/src/inc/Conditionals_adv.h +++ b/Marlin/src/inc/Conditionals_adv.h @@ -542,3 +542,10 @@ #else #define HAS_USER_ITEM(N) 0 #endif + +#if !HAS_MULTI_SERIAL + #undef MEATPACK_ON_SERIAL_PORT_2 +#endif +#if EITHER(MEATPACK_ON_SERIAL_PORT_1, MEATPACK_ON_SERIAL_PORT_2) + #define HAS_MEATPACK 1 +#endif diff --git a/Marlin/src/inc/Conditionals_post.h b/Marlin/src/inc/Conditionals_post.h index a6567e9714..fb06a7a3f3 100644 --- a/Marlin/src/inc/Conditionals_post.h +++ b/Marlin/src/inc/Conditionals_post.h @@ -2906,16 +2906,3 @@ #if BUTTONS_EXIST(EN1, EN2, ENC) #define HAS_ROTARY_ENCODER 1 #endif - -#if !NUM_SERIAL - #undef BAUD_RATE_GCODE -#elif NUM_SERIAL > 1 - #define HAS_MULTI_SERIAL 1 -#endif - -#if !HAS_MULTI_SERIAL - #undef MEATPACK_ON_SERIAL_PORT_2 -#endif -#if EITHER(MEATPACK_ON_SERIAL_PORT_1, MEATPACK_ON_SERIAL_PORT_2) - #define HAS_MEATPACK 1 -#endif diff --git a/Marlin/src/inc/SanityCheck.h b/Marlin/src/inc/SanityCheck.h index 6802bff1dd..af30c6156d 100644 --- a/Marlin/src/inc/SanityCheck.h +++ b/Marlin/src/inc/SanityCheck.h @@ -2353,6 +2353,7 @@ static_assert(hbm[Z_AXIS] >= 0, "HOMING_BUMP_MM.Z must be greater than or equal + ENABLED(MAKEBOARD_MINI_2_LINE_DISPLAY_1602) \ + ENABLED(MAKRPANEL) \ + ENABLED(MALYAN_LCD) \ + + ENABLED(NEXTION_TFT) \ + ENABLED(MKS_LCD12864) \ + ENABLED(OLED_PANEL_TINYBOY2) \ + ENABLED(OVERLORD_OLED) \ @@ -2372,7 +2373,9 @@ static_assert(hbm[Z_AXIS] >= 0, "HOMING_BUMP_MM.Z must be greater than or equal + ENABLED(ULTIPANEL) \ + ENABLED(ULTRA_LCD) \ + ENABLED(YHCB2004) \ - + ENABLED(ZONESTAR_LCD) + + ENABLED(ZONESTAR_LCD) \ + + ENABLED(K3D_FULL_GRAPHIC_SMART_CONTROLLER) \ + + ENABLED(K3D_242_OLED_CONTROLLER) #error "Please select only one LCD controller option." #endif diff --git a/Marlin/src/inc/Version.h b/Marlin/src/inc/Version.h index c9760f3f69..6d14c41121 100644 --- a/Marlin/src/inc/Version.h +++ b/Marlin/src/inc/Version.h @@ -42,7 +42,7 @@ * version was tagged. */ #ifndef STRING_DISTRIBUTION_DATE - #define STRING_DISTRIBUTION_DATE "2021-03-12" + #define STRING_DISTRIBUTION_DATE "2021-03-20" #endif /** diff --git a/Marlin/src/lcd/dogm/marlinui_DOGM.cpp b/Marlin/src/lcd/dogm/marlinui_DOGM.cpp index d2b1ce7740..7334ba5f26 100644 --- a/Marlin/src/lcd/dogm/marlinui_DOGM.cpp +++ b/Marlin/src/lcd/dogm/marlinui_DOGM.cpp @@ -256,7 +256,7 @@ void MarlinUI::init_lcd() { OUT_WRITE(LCD_BACKLIGHT_PIN, DISABLED(DELAYED_BACKLIGHT_INIT)); // Illuminate after reset or right away #endif - #if ANY(MKS_12864OLED, MKS_12864OLED_SSD1306, FYSETC_242_OLED_12864, ZONESTAR_12864OLED) + #if ANY(MKS_12864OLED, MKS_12864OLED_SSD1306, FYSETC_242_OLED_12864, ZONESTAR_12864OLED, K3D_242_OLED_CONTROLLER) SET_OUTPUT(LCD_PINS_DC); #ifndef LCD_RESET_PIN #define LCD_RESET_PIN LCD_PINS_RS diff --git a/Marlin/src/lcd/dogm/marlinui_DOGM.h b/Marlin/src/lcd/dogm/marlinui_DOGM.h index e5862d670f..e3ceb63f96 100644 --- a/Marlin/src/lcd/dogm/marlinui_DOGM.h +++ b/Marlin/src/lcd/dogm/marlinui_DOGM.h @@ -123,9 +123,10 @@ #define U8G_CLASS U8GLIB_SSD1306_128X64 // 8 stripes #endif -#elif ENABLED(FYSETC_242_OLED_12864) +#elif EITHER(FYSETC_242_OLED_12864, K3D_242_OLED_CONTROLLER) - // FYSETC OLED 2.42" 128 × 64 FULL GRAPHICS CONTROLLER + // FYSETC OLED 2.42" 128 × 64 Full Graphics Controller + // or K3D OLED 2.42" 128 × 64 Full Graphics Controller #define FORCE_SOFT_SPI // SW-SPI diff --git a/Marlin/src/lcd/dwin/e3v2/dwin.cpp b/Marlin/src/lcd/dwin/e3v2/dwin.cpp index e046bb90f5..97a9fbd4da 100644 --- a/Marlin/src/lcd/dwin/e3v2/dwin.cpp +++ b/Marlin/src/lcd/dwin/e3v2/dwin.cpp @@ -1469,19 +1469,21 @@ void HMI_PrintSpeed() { } } +#define LAST_AXIS TERN(HAS_HOTEND, E_AXIS, Z_AXIS) + void HMI_MaxFeedspeedXYZE() { ENCODER_DiffState encoder_diffState = Encoder_ReceiveAnalyze(); if (encoder_diffState != ENCODER_DIFF_NO) { if (Apply_Encoder(encoder_diffState, HMI_ValueStruct.Max_Feedspeed)) { checkkey = MaxSpeed; EncoderRate.enabled = false; - if (WITHIN(HMI_flag.feedspeed_axis, X_AXIS, E_AXIS)) + if (WITHIN(HMI_flag.feedspeed_axis, X_AXIS, LAST_AXIS)) planner.set_max_feedrate(HMI_flag.feedspeed_axis, HMI_ValueStruct.Max_Feedspeed); DWIN_Draw_IntValue(true, true, 0, font8x16, Color_White, Color_Bg_Black, 4, 210, MBASE(select_speed.now), HMI_ValueStruct.Max_Feedspeed); return; } // MaxFeedspeed limit - if (WITHIN(HMI_flag.feedspeed_axis, X_AXIS, E_AXIS)) + if (WITHIN(HMI_flag.feedspeed_axis, X_AXIS, LAST_AXIS)) NOMORE(HMI_ValueStruct.Max_Feedspeed, default_max_feedrate[HMI_flag.feedspeed_axis] * 2); if (HMI_ValueStruct.Max_Feedspeed < MIN_MAXFEEDSPEED) HMI_ValueStruct.Max_Feedspeed = MIN_MAXFEEDSPEED; // MaxFeedspeed value @@ -1495,17 +1497,13 @@ void HMI_MaxAccelerationXYZE() { if (Apply_Encoder(encoder_diffState, HMI_ValueStruct.Max_Acceleration)) { checkkey = MaxAcceleration; EncoderRate.enabled = false; - if (HMI_flag.acc_axis == X_AXIS) planner.set_max_acceleration(X_AXIS, HMI_ValueStruct.Max_Acceleration); - else if (HMI_flag.acc_axis == Y_AXIS) planner.set_max_acceleration(Y_AXIS, HMI_ValueStruct.Max_Acceleration); - else if (HMI_flag.acc_axis == Z_AXIS) planner.set_max_acceleration(Z_AXIS, HMI_ValueStruct.Max_Acceleration); - #if HAS_HOTEND - else if (HMI_flag.acc_axis == E_AXIS) planner.set_max_acceleration(E_AXIS, HMI_ValueStruct.Max_Acceleration); - #endif + if (WITHIN(HMI_flag.acc_axis, X_AXIS, LAST_AXIS)) + planner.set_max_acceleration(HMI_flag.acc_axis, HMI_ValueStruct.Max_Acceleration); DWIN_Draw_IntValue(true, true, 0, font8x16, Color_White, Color_Bg_Black, 4, 210, MBASE(select_acc.now), HMI_ValueStruct.Max_Acceleration); return; } // MaxAcceleration limit - if (WITHIN(HMI_flag.acc_axis, X_AXIS, E_AXIS)) + if (WITHIN(HMI_flag.acc_axis, X_AXIS, LAST_AXIS)) NOMORE(HMI_ValueStruct.Max_Acceleration, default_max_acceleration[HMI_flag.acc_axis] * 2); if (HMI_ValueStruct.Max_Acceleration < MIN_MAXACCELERATION) HMI_ValueStruct.Max_Acceleration = MIN_MAXACCELERATION; // MaxAcceleration value @@ -1521,13 +1519,13 @@ void HMI_MaxAccelerationXYZE() { if (Apply_Encoder(encoder_diffState, HMI_ValueStruct.Max_Jerk_scaled)) { checkkey = MaxJerk; EncoderRate.enabled = false; - if (WITHIN(HMI_flag.jerk_axis, X_AXIS, E_AXIS)) + if (WITHIN(HMI_flag.jerk_axis, X_AXIS, LAST_AXIS)) planner.set_max_jerk(HMI_flag.jerk_axis, HMI_ValueStruct.Max_Jerk_scaled / 10); DWIN_Draw_FloatValue(true, true, 0, font8x16, Color_White, Color_Bg_Black, 3, 1, 210, MBASE(select_jerk.now), HMI_ValueStruct.Max_Jerk_scaled); return; } // MaxJerk limit - if (WITHIN(HMI_flag.jerk_axis, X_AXIS, E_AXIS)) + if (WITHIN(HMI_flag.jerk_axis, X_AXIS, LAST_AXIS)) NOMORE(HMI_ValueStruct.Max_Jerk_scaled, default_max_jerk[HMI_flag.jerk_axis] * 2 * MINUNITMULT); NOLESS(HMI_ValueStruct.Max_Jerk_scaled, (MIN_MAXJERK) * MINUNITMULT); // MaxJerk value @@ -1543,13 +1541,13 @@ void HMI_StepXYZE() { if (Apply_Encoder(encoder_diffState, HMI_ValueStruct.Max_Step_scaled)) { checkkey = Step; EncoderRate.enabled = false; - if (WITHIN(HMI_flag.step_axis, X_AXIS, E_AXIS)) + if (WITHIN(HMI_flag.step_axis, X_AXIS, LAST_AXIS)) planner.settings.axis_steps_per_mm[HMI_flag.step_axis] = HMI_ValueStruct.Max_Step_scaled / 10; DWIN_Draw_FloatValue(true, true, 0, font8x16, Color_White, Color_Bg_Black, 3, 1, 210, MBASE(select_step.now), HMI_ValueStruct.Max_Step_scaled); return; } // Step limit - if (WITHIN(HMI_flag.step_axis, X_AXIS, E_AXIS)) + if (WITHIN(HMI_flag.step_axis, X_AXIS, LAST_AXIS)) NOMORE(HMI_ValueStruct.Max_Step_scaled, 999.9 * MINUNITMULT); NOLESS(HMI_ValueStruct.Max_Step_scaled, MIN_STEP); // Step value diff --git a/Marlin/src/lcd/extui/lib/nextion/FileNavigator.cpp b/Marlin/src/lcd/extui/lib/nextion/FileNavigator.cpp new file mode 100644 index 0000000000..f82ce1f091 --- /dev/null +++ b/Marlin/src/lcd/extui/lib/nextion/FileNavigator.cpp @@ -0,0 +1,174 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2021 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + +/* **************************************** + * lcd/extui/lib/nextion/FileNavigator.cpp + * **************************************** + * Extensible_UI implementation for Nextion + * https://github.com/Skorpi08 + * ***************************************/ + +#include "../../../../inc/MarlinConfigPre.h" + +#if ENABLED(NEXTION_TFT) + +#include "FileNavigator.h" +#include "nextion_tft.h" + +using namespace ExtUI; + +#define DEBUG_OUT NEXDEBUGLEVEL +#include "../../../../core/debug_out.h" + +FileList FileNavigator::filelist; // Instance of the Marlin file API +char FileNavigator::currentfoldername[MAX_PATH_LEN]; // Current folder path +uint16_t FileNavigator::lastindex; +uint8_t FileNavigator::folderdepth; +uint16_t FileNavigator::currentindex; // override the panel request + +FileNavigator filenavigator; + +FileNavigator::FileNavigator() { reset(); } + +void FileNavigator::reset() { + currentfoldername[0] = '\0'; + folderdepth = 0; + currentindex = 0; + lastindex = 0; + // Start at root folder + while (!filelist.isAtRootDir()) filelist.upDir(); + refresh(); +} + +void FileNavigator::refresh() { filelist.refresh(); } + +void FileNavigator::getFiles(uint16_t index) { + uint16_t files = 7, fseek = 0, fcnt = 0; + if (index == 0) + currentindex = 0; + else { + // Each time we change folder we reset the file index to 0 and keep track + // of the current position as the TFT panel isn't aware of folder trees. + --currentindex; // go back a file to take account of the .. added to the root. + if (index > lastindex) + currentindex += files + 1; + else if (currentindex >= files) + currentindex -= files - 1; + else + currentindex = 0; + } + lastindex = index; + + #if NEXDEBUG(AC_FILE) + DEBUG_ECHOLNPAIR("index=", index, " currentindex=", currentindex); + #endif + + if (currentindex == 0 && folderdepth > 0) { // Add a link to go up a folder + nextion.SendtoTFT(PSTR("vis p0,1")); + nextion.SendtoTFT(PSTR("\xFF\xFF\xFF")); + SEND_VAL("tmpUP", "0"); + files--; + } + else { + nextion.SendtoTFT(PSTR("vis p0,0")); + nextion.SendtoTFT(PSTR("\xFF\xFF\xFF")); + } + + for (uint16_t seek = currentindex; seek < currentindex + files; seek++) { + if (filelist.seek(seek)) { + nextion.SendtoTFT(PSTR("s")); + LCD_SERIAL.print(fcnt); + nextion.SendtoTFT(PSTR(".txt=\"")); + if (filelist.isDir()) { + LCD_SERIAL.print(filelist.shortFilename()); + nextion.SendtoTFT(PSTR("/\"")); + nextion.SendtoTFT(PSTR("\xFF\xFF\xFF")); + + nextion.SendtoTFT(PSTR("l")); + LCD_SERIAL.print(fcnt); + nextion.SendtoTFT(PSTR(".txt=\"")); + LCD_SERIAL.print(filelist.filename()); + nextion.SendtoTFT(PSTR("\"")); + nextion.SendtoTFT(PSTR("\xFF\xFF\xFF")); + SEND_PCO2("l", fcnt, "1055"); + } + else { + LCD_SERIAL.print(currentfoldername); + LCD_SERIAL.print(filelist.shortFilename()); + nextion.SendtoTFT(PSTR("\"")); + nextion.SendtoTFT(PSTR("\xFF\xFF\xFF")); + + nextion.SendtoTFT(PSTR("l")); + LCD_SERIAL.print(fcnt); + nextion.SendtoTFT(PSTR(".txt=\"")); + LCD_SERIAL.print(filelist.longFilename()); + nextion.SendtoTFT(PSTR("\"")); + nextion.SendtoTFT(PSTR("\xFF\xFF\xFF")); + } + fcnt++; + fseek = seek; + #if NEXDEBUG(AC_FILE) + DEBUG_ECHOLNPAIR("-", seek, " '", filelist.longFilename(), "' '", currentfoldername, "", filelist.shortFilename(), "'\n"); + #endif + } + } + SEND_VAL("n0", filelist.count()); + SEND_VAL("n1", fseek + 1); +} + +void FileNavigator::changeDIR(char *folder) { + #if NEXDEBUG(AC_FILE) + DEBUG_ECHOLNPAIR("currentfolder: ", currentfoldername, " New: ", folder); + #endif + if (folderdepth >= MAX_FOLDER_DEPTH) return; // limit the folder depth + strcat(currentfoldername, folder); + strcat(currentfoldername, "/"); + filelist.changeDir(folder); + refresh(); + folderdepth++; + currentindex = 0; +} + +void FileNavigator::upDIR() { + filelist.upDir(); + refresh(); + folderdepth--; + currentindex = 0; + // Remove the last child folder from the stored path + if (folderdepth == 0) { + currentfoldername[0] = '\0'; + reset(); + } + else { + char *pos = nullptr; + for (uint8_t f = 0; f < folderdepth; f++) + pos = strchr(currentfoldername, '/'); + pos[1] = '\0'; + } + #if NEXDEBUG(AC_FILE) + DEBUG_ECHOLNPAIR("depth: ", folderdepth, " currentfoldername: ", currentfoldername); + #endif +} + +char* FileNavigator::getCurrentFolderName() { return currentfoldername; } + +#endif // NEXTION_TFT diff --git a/Marlin/src/lcd/extui/lib/nextion/FileNavigator.h b/Marlin/src/lcd/extui/lib/nextion/FileNavigator.h new file mode 100644 index 0000000000..1cd29ec671 --- /dev/null +++ b/Marlin/src/lcd/extui/lib/nextion/FileNavigator.h @@ -0,0 +1,53 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2021 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/* **************************************** + * lcd/extui/lib/nextion/FileNavigator.cpp + * **************************************** + * Extensible_UI implementation for Nextion + * https://github.com/Skorpi08 + * ***************************************/ + +#include "nextion_tft_defs.h" // for MAX_PATH_LEN +#include "../../ui_api.h" + +using namespace ExtUI; + +class FileNavigator { + public: + FileNavigator(); + static void reset(); + static void getFiles(uint16_t); + static void upDIR(); + static void changeDIR(char *); + static void refresh(); + static char* getCurrentFolderName(); + private: + static FileList filelist; + static char currentfoldername[MAX_PATH_LEN]; + static uint16_t lastindex; + static uint8_t folderdepth; + static uint16_t currentindex; +}; + +extern FileNavigator filenavigator; diff --git a/Marlin/src/lcd/extui/lib/nextion/nextion_tft.cpp b/Marlin/src/lcd/extui/lib/nextion/nextion_tft.cpp new file mode 100644 index 0000000000..12a7bc7cc7 --- /dev/null +++ b/Marlin/src/lcd/extui/lib/nextion/nextion_tft.cpp @@ -0,0 +1,729 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2021 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + +/* **************************************** + * lcd/extui/lib/nextion/nextion_tft.h + * **************************************** + * Extensible_UI implementation for Nextion + * https://github.com/Skorpi08 + * ***************************************/ + +#include "../../../../inc/MarlinConfigPre.h" + +#if ENABLED(NEXTION_TFT) + +#include "../../../../MarlinCore.h" +#include "../../../../feature/pause.h" +#include "../../../../gcode/queue.h" +#include "../../../../libs/numtostr.h" +#include "../../../../sd/cardreader.h" +#include "FileNavigator.h" +#include "nextion_tft.h" + +#define DEBUG_OUT NEXDEBUGLEVEL +#include "../../../../core/debug_out.h" + +char NextionTFT::selectedfile[MAX_PATH_LEN]; +char NextionTFT::nextion_command[MAX_CMND_LEN]; +uint8_t NextionTFT::command_len; + +bool last_homed = 0, last_homedX = 0, last_homedY = 0, last_homedZ = 0; +float last_degBed = 999, last_degHotend0 = 999, last_degHotend1 = 999, last_degTargetBed = 999, last_degTargetHotend0 = 999, last_degTargetHotend1 = 999; +float last_get_axis_position_mmX = 999, last_get_axis_position_mmY = 999, last_get_axis_position_mmZ = 999; +float last_extruder_advance_K = 999; +uint8_t last_active_extruder = 99, last_fan_speed = 99, last_print_speed = 99, last_flow_speed = 99, last_progress = 99; +uint8_t last_printer_state = 99, last_IDEX_Mode = 99; +uint32_t layer = 0, last_layer = 99; + +NextionTFT nextion; + +NextionTFT::NextionTFT() {} + +void NextionTFT::Startup() { + selectedfile[0] = '\0'; + nextion_command[0] = '\0'; + command_len = 0; + LCD_SERIAL.begin(115200); + + SEND_VAL("tmppage.connected", 0); + delay_ms(100); + SEND_VAL("tmppage.connected", 1); + + SEND_VALasTXT("tmppage.marlin", SHORT_BUILD_VERSION); + SEND_VALasTXT("tmppage.compiled", __DATE__ " / " __TIME__); + SEND_VALasTXT("tmppage.extruder", EXTRUDERS); + SEND_VALasTXT("tmppage.printer", MACHINE_NAME); + SEND_VALasTXT("tmppage.author", STRING_CONFIG_H_AUTHOR); + SEND_VALasTXT("tmppage.released", STRING_DISTRIBUTION_DATE); + SEND_VALasTXT("tmppage.bedx", X_BED_SIZE); + SEND_VALasTXT("tmppage.bedy", Y_BED_SIZE); + SEND_VALasTXT("tmppage.bedz", Z_MAX_POS); + + DEBUG_ECHOLNPAIR("Nextion Debug Level ", NEXDEBUGLEVEL); +} + +void NextionTFT::IdleLoop() { + if (ReadTFTCommand()) { + ProcessPanelRequest(); + command_len = 0; + } + UpdateOnChange(); +} + +void NextionTFT::PrinterKilled(PGM_P error, PGM_P component) { + SEND_TXT_END("page error"); + SEND_TXT("t3", "Error"); + SEND_TXT_P("t4", component); + SEND_TXT_P("t5", error); + SEND_TXT("t6", "Need reset"); +} + +void NextionTFT::PrintFinished() { + SEND_TXT_END("page printfinished"); +} + +void NextionTFT::ConfirmationRequest(const char *const msg) { + SEND_VALasTXT("tmppage.M117", msg); + #if NEXDEBUG(N_MARLIN) + DEBUG_ECHOLNPAIR("ConfirmationRequest() ", msg, " printer_state:", printer_state); + #endif +} + +void NextionTFT::StatusChange(const char *const msg) { + #if NEXDEBUG(N_MARLIN) + DEBUG_ECHOLNPAIR("StatusChange() ", msg, "\nprinter_state:", printer_state); + #endif + SEND_VALasTXT("tmppage.M117", msg); +} + +void NextionTFT::SendtoTFT(PGM_P str) { // A helper to print PROGMEM string to the panel + #if NEXDEBUG(N_SOME) + DEBUG_ECHOPGM_P(str); + #endif + while (const char c = pgm_read_byte(str++)) + LCD_SERIAL.write(c); +} + +bool NextionTFT::ReadTFTCommand() { + bool command_ready = false; + while ((LCD_SERIAL.available() > 0) && (command_len < MAX_CMND_LEN)) { + nextion_command[command_len] = LCD_SERIAL.read(); + if (nextion_command[command_len] == 10) { + command_ready = true; + break; + } + command_len++; + } + + if (command_ready) { + nextion_command[command_len] = 0x00; + if (nextion_command[0] == 'G' || nextion_command[0] == 'M' || nextion_command[0] == 'T') + injectCommands(nextion_command); + #if NEXDEBUG(N_ALL) + DEBUG_ECHOLNPAIR("< ", nextion_command); + #endif + #if NEXDEBUG(N_SOME) + uint8_t req = atoi(&nextion_command[1]); + if (req > 7 && req != 20) + DEBUG_ECHOLNPAIR( "> ", nextion_command[0], + "\n> ", nextion_command[1], + "\n> ", nextion_command[2], + "\n> ", nextion_command[3], + "\nprinter_state:", printer_state); + #endif + } + return command_ready; +} + +void NextionTFT::SendFileList(int8_t startindex) { + // respond to panel request for 7 files starting at index + #if NEXDEBUG(N_INFO) + DEBUG_ECHOLNPAIR("## SendFileList ## ", startindex); + #endif + filenavigator.getFiles(startindex); +} + +void NextionTFT::SelectFile() { + strncpy(selectedfile, nextion_command + 4, command_len - 4); + selectedfile[command_len - 5] = '\0'; + #if NEXDEBUG(N_FILE) + DEBUG_ECHOLNPAIR_F(" Selected File: ", selectedfile); + #endif + switch (selectedfile[0]) { + case '/': // Valid file selected + //SEND_TXT("tmppage.M117", msg_sd_file_open_success); + break; + case '<': // .. (go up folder level) + filenavigator.upDIR(); + SendFileList(0); + break; + default: // enter sub folder + filenavigator.changeDIR(selectedfile); + SendFileList(0); + break; + } +} + +void NextionTFT::_format_time(char *outstr, uint32_t time) { + const uint8_t hrs = time / 3600, + min = (time / 60) % 60, + sec = time % 60; + if (hrs) + sprintf_P(outstr, PSTR("%02d:%02dm"), hrs, min); + else + sprintf_P(outstr, PSTR("%02d:%02ds"), min, sec); +} + +void NextionTFT::ProcessPanelRequest() { + // Break these up into logical blocks as its easier to navigate than one huge switch case! + if (nextion_command[0] == 'X') { + int8_t req = atoi(&nextion_command[1]); + + // Information requests + if (req <= 49) + PanelInfo(req); + + // Simple Actions + else if (req >= 50) + PanelAction(req); + } +} + +#define SEND_NA(A) SEND_TXT(A, "n/a") + +void NextionTFT::PanelInfo(uint8_t req) { + switch (req) { + case 0: break; + + case 1: // Get SD Card list + if (!isPrinting()) { + if (!isMediaInserted()) safe_delay(500); + if (!isMediaInserted()) { // Make sure the card is removed + //SEND_TXT("tmppage.M117", msg_no_sd_card); + } + else if (nextion_command[3] == 'S') + SendFileList(atoi(&nextion_command[4])); + } + break; + + case 2: // Printer Info + if (!isPrinting()) { + SEND_VAL("tmppage.connected", 1); + SEND_VALasTXT("tmppage.marlin", SHORT_BUILD_VERSION); + SEND_VALasTXT("tmppage.compiled", __DATE__ " / " __TIME__); + SEND_VALasTXT("tmppage.extruder", EXTRUDERS); + SEND_VALasTXT("tmppage.printer", MACHINE_NAME); + SEND_VALasTXT("tmppage.author", STRING_CONFIG_H_AUTHOR); + SEND_VALasTXT("tmppage.released", STRING_DISTRIBUTION_DATE); + SEND_VALasTXT("tmppage.bedx", X_BED_SIZE); + SEND_VALasTXT("tmppage.bedy", Y_BED_SIZE); + SEND_VALasTXT("tmppage.bedz", Z_MAX_POS); + SEND_TEMP("tmppage.t0", ui8tostr3rj(getActualTemp_celsius(E0)), " / ", ui8tostr3rj(getTargetTemp_celsius(E0))); + SEND_TEMP("tmppage.t1", ui8tostr3rj(getActualTemp_celsius(E1)), " / ", ui8tostr3rj(getTargetTemp_celsius(E1))); + SEND_TEMP("tmppage.t2", ui8tostr3rj(getActualTemp_celsius(BED)), " / ", ui8tostr3rj(getTargetTemp_celsius(BED))); + SEND_VALasTXT("tmppage.tool", getActiveTool()); + SEND_VALasTXT("tmppage.fan", ui8tostr3rj(getActualFan_percent(FAN0))); + SEND_VALasTXT("tmppage.speed", getFeedrate_percent()); + SEND_VALasTXT("tmppage.flow", getFlowPercentage(getActiveTool())); + SEND_VALasTXT("tmppage.progress", ui8tostr3rj(getProgress_percent())); + SEND_VALasTXT("tmppage.layer", layer); + SEND_VALasTXT("tmppage.x", getAxisPosition_mm(X)); + SEND_VALasTXT("tmppage.y", getAxisPosition_mm(Y)); + SEND_VALasTXT("tmppage.z", getAxisPosition_mm(Z)); + SEND_VAL("tmppage.homed", isPositionKnown()); + SEND_VAL("tmppage.homedx", isAxisPositionKnown(X)); + SEND_VAL("tmppage.homedy", isAxisPositionKnown(Y)); + SEND_VAL("tmppage.homedz", isAxisPositionKnown(Z)); + #if ENABLED(DUAL_X_CARRIAGE) + SEND_VAL("tmppage.idexmode", getIDEX_Mode()); + #endif + SEND_TXT("tmppage.M117", msg_welcome); + } + break; + + case 23: // Linear Advance + #if ENABLED(LIN_ADVANCE) + SEND_VALasTXT("linadvance", getLinearAdvance_mm_mm_s(getActiveTool())); + #else + SEND_NA("linadvance"); + #endif + break; + + case 24: // TMC Motor Current + #if HAS_TRINAMIC_CONFIG + #define SEND_TRINAMIC_CURR(A, B) SEND_VALasTXT(A, getAxisCurrent_mA(B)) + #else + #define SEND_TRINAMIC_CURR(A, B) SEND_NA(A) + #endif + SEND_TRINAMIC_CURR("x", X); + SEND_TRINAMIC_CURR("x2", X2); + SEND_TRINAMIC_CURR("y", Y); + SEND_TRINAMIC_CURR("y2", Y2); + SEND_TRINAMIC_CURR("z", Z); + SEND_TRINAMIC_CURR("z2", Z2); + SEND_TRINAMIC_CURR("e", E0); + SEND_TRINAMIC_CURR("e1", E1); + break; + + case 25: // TMC Bump Sensitivity + #if HAS_TRINAMIC_CONFIG + #define SEND_TRINAMIC_BUMP(A, B) SEND_VALasTXT(A, getTMCBumpSensitivity(B)) + #else + #define SEND_TRINAMIC_BUMP(A, B) SEND_NA(A) + #endif + SEND_TRINAMIC_BUMP("x", X); + SEND_TRINAMIC_BUMP("x2", X2); + SEND_TRINAMIC_BUMP("y", Y); + SEND_TRINAMIC_BUMP("y2", Y2); + SEND_TRINAMIC_BUMP("z", Z); + SEND_TRINAMIC_BUMP("z2", Z2); + break; + + case 26: // TMC Hybrid Threshold Speed + #if 0 && BOTH(HAS_TRINAMIC_CONFIG, HYBRID_THRESHOLD) + #define SEND_TRINAMIC_THRS(A, B) SEND_VALasTXT(A, getAxisPWMthrs(B)) + #else + #define SEND_TRINAMIC_THRS(A, B) SEND_NA(A) + #endif + SEND_TRINAMIC_THRS("x", X); + SEND_TRINAMIC_THRS("x2", X2); + SEND_TRINAMIC_THRS("y", Y); + SEND_TRINAMIC_THRS("y2", Y2); + SEND_TRINAMIC_THRS("z", Z); + SEND_TRINAMIC_THRS("z2", Z2); + SEND_TRINAMIC_THRS("e", E0); + SEND_TRINAMIC_THRS("e1", E1); + break; + + case 27: // Printcounter + #if ENABLED(PRINTCOUNTER) + char buffer[21]; + #define SEND_PRINT_INFO(A, B) SEND_VALasTXT(A, B(buffer)) + #else + #define SEND_PRINT_INFO(A, B) SEND_NA(A) + #endif + SEND_PRINT_INFO("t5", getTotalPrints_str); + SEND_PRINT_INFO("t3", getFinishedPrints_str); + SEND_PRINT_INFO("t4", getFailedPrints_str); + SEND_PRINT_INFO("t6", getTotalPrintTime_str); + SEND_PRINT_INFO("t7", getLongestPrint_str); + SEND_PRINT_INFO("t8", getFilamentUsed_str); + break; + + case 28: // Filament laod/unload + #if ENABLED(ADVANCED_PAUSE_FEATURE) + #define SEND_PAUSE_INFO(A, B) SEND_VALasTXT(A, fc_settings[getActiveTool()].B) + #else + #define SEND_PAUSE_INFO(A, B) SEND_NA(A) + #endif + SEND_PAUSE_INFO("filamentin", load_length); + SEND_PAUSE_INFO("filamentout", unload_length); + break; + + case 29: // Preheat + #if PREHEAT_COUNT + if (!isPrinting()) { + // Preheat PLA + if (nextion_command[4] == 'P') { + SEND_VALasTXT("pe", getMaterial_preset_E(0)); + #if HAS_HEATED_BED + SEND_VALasTXT("pb", getMaterial_preset_B(0)); + #endif + } + + // Preheat ABS + if (nextion_command[4] == 'A') { + SEND_VALasTXT("ae", getMaterial_preset_E(1)); + #if HAS_HEATED_BED + SEND_VALasTXT("ab", getMaterial_preset_B(1)); + #endif + } + + // Preheat PETG + if (nextion_command[4] == 'G') { + #ifdef PREHEAT_3_TEMP_HOTEND + SEND_VALasTXT("ge", getMaterial_preset_E(2)); + #if HAS_HEATED_BED + SEND_VALasTXT("gb", getMaterial_preset_B(2)); + #endif + #endif + } + } + #endif + break; + + case 30: // Velocity + SEND_VALasTXT("x", getAxisMaxFeedrate_mm_s(X)); + SEND_VALasTXT("y", getAxisMaxFeedrate_mm_s(Y)); + SEND_VALasTXT("z", getAxisMaxFeedrate_mm_s(Z)); + SEND_VALasTXT("e", getAxisMaxFeedrate_mm_s(getActiveTool())); + SEND_VALasTXT("min", getMinFeedrate_mm_s()); + SEND_VALasTXT("tmin", getMinTravelFeedrate_mm_s()); + break; + + case 31: // Jerk + #if ENABLED(CLASSIC_JERK) + #define SEND_JERK_INFO(A, B) SEND_VALasTXT(A, getAxisMaxJerk_mm_s(B)) + #else + #define SEND_JERK_INFO(A, B) SEND_NA(A) + //SEND_VALasTXT("x", getJunctionDeviation_mm()); + SEND_TXT("tmppage.M117", "classic Jerk not enabled"); + #endif + SEND_JERK_INFO("x", X); + SEND_JERK_INFO("y", Y); + SEND_JERK_INFO("z", Z); + SEND_JERK_INFO("e", getActiveTool()); + break; + + case 32: // Steps-per-mm + SEND_VALasTXT("x", getAxisSteps_per_mm(X)); + SEND_VALasTXT("y", getAxisSteps_per_mm(Y)); + SEND_VALasTXT("z", getAxisSteps_per_mm(Z)); + SEND_VALasTXT("e0", getAxisSteps_per_mm(E0)); + SEND_VALasTXT("e1", getAxisSteps_per_mm(E1)); + break; + + case 33: // Acceleration + SEND_VALasTXT("x", ui16tostr5rj(getAxisMaxAcceleration_mm_s2(X))); + SEND_VALasTXT("y", ui16tostr5rj(getAxisMaxAcceleration_mm_s2(Y))); + SEND_VALasTXT("z", ui16tostr5rj(getAxisMaxAcceleration_mm_s2(Z))); + SEND_VALasTXT("e", ui16tostr5rj(getAxisMaxAcceleration_mm_s2(getActiveTool()))); + SEND_VALasTXT("print", ui16tostr5rj(getPrintingAcceleration_mm_s2())); + SEND_VALasTXT("retract", ui16tostr5rj(getRetractAcceleration_mm_s2())); + SEND_VALasTXT("travel", ui16tostr5rj(getTravelAcceleration_mm_s2())); + break; + + case 34: // Dual X carriage offset + #if ENABLED(DUAL_X_CARRIAGE) + #define SEND_IDEX_INFO(A, B) SEND_VALasTXT(A, getNozzleOffset_mm(B, getActiveTool())) + #else + #define SEND_IDEX_INFO(A, B) SEND_NA(A) + #endif + SEND_IDEX_INFO("x", X); + SEND_IDEX_INFO("y", Y); + SEND_IDEX_INFO("z", Z); + break; + + case 35: // Probe offset + #if HAS_PROBE_XY_OFFSET + #define SEND_PROBE_INFO(A, B) SEND_VALasTXT(A, getProbeOffset_mm(B)) + #else + #define SEND_PROBE_INFO(A, B) SEND_NA(A) + #endif + SEND_PROBE_INFO("x", X); + SEND_PROBE_INFO("y", Y); + SEND_VALasTXT("z", getZOffset_mm()); + break; + + case 36: // Endstop Info + #if HAS_X_MIN + SEND_VALasTXT("x1", READ(X_MIN_PIN) != X_MIN_ENDSTOP_INVERTING ? "triggered" : "open"); + #endif + #if HAS_X_MAX + SEND_VALasTXT("x2", READ(X_MAX_PIN) != X_MAX_ENDSTOP_INVERTING ? "triggered" : "open"); + #endif + #if HAS_Y_MIN + SEND_VALasTXT("y1", READ(Y_MIN_PIN) != Y_MIN_ENDSTOP_INVERTING ? "triggered" : "open"); + #endif + #if HAS_Z_MIN + SEND_VALasTXT("z1", READ(Z_MIN_PIN) != Z_MIN_ENDSTOP_INVERTING ? "triggered" : "open"); + #endif + #if HAS_Z_MAX + SEND_VALasTXT("z2", READ(Z_MAX_PIN) != Z_MAX_ENDSTOP_INVERTING ? "triggered" : "open"); + #endif + #if HAS_Z2_MIN + SEND_VALasTXT("z2", READ(Z2_MIN_PIN) != Z2_MIN_ENDSTOP_INVERTING ? "triggered" : "open"); + #endif + #if HAS_Z2_MAX + SEND_VALasTXT("z2", READ(Z2_MAX_PIN) != Z2_MAX_ENDSTOP_INVERTING ? "triggered" : "open"); + #endif + #if HAS_BED_PROBE + //SEND_VALasTXT("bltouch", READ(Z_MIN_PROBE_PIN) != Z_MIN_PROBE_ENDSTOP_INVERTING ? "triggered" : "open"); + #else + SEND_NA("bltouch"); + #endif + break; + + case 37: // PID + #if ENABLED(PIDTEMP) + #define SEND_PID_INFO_0(A, B) SEND_VALasTXT(A, getPIDValues_K##B(E0)) + #else + #define SEND_PID_INFO_0(A, B) SEND_NA(A) + #endif + #if BOTH(PIDTEMP, HAS_MULTI_EXTRUDER) + #define SEND_PID_INFO_1(A, B) SEND_VALasTXT(A, getPIDValues_K##B(E1)) + #else + #define SEND_PID_INFO_1(A, B) SEND_NA(A) + #endif + #if ENABLED(PIDTEMPBED) + #define SEND_PID_INFO_BED(A, B) SEND_VALasTXT(A, getBedPIDValues_K##B()) + #else + #define SEND_PID_INFO_BED(A, B) SEND_NA(A) + #endif + SEND_PID_INFO_0("p0", p); + SEND_PID_INFO_0("i0", i); + SEND_PID_INFO_0("d0", d); + + SEND_PID_INFO_1("p1", p); + SEND_PID_INFO_1("i1", i); + SEND_PID_INFO_1("d1", d); + + SEND_PID_INFO_BED("hbp", p); + SEND_PID_INFO_BED("hbi", i); + SEND_PID_INFO_BED("hbd", d); + break; + } +} + +void NextionTFT::PanelAction(uint8_t req) { + switch (req) { + + case 50: // Pause SD print + //if (isPrintingFromMedia()) { + //SEND_TXT("tmppage.M117", "Paused"); + pausePrint(); + SEND_TXT_END("qpause.picc=29"); + //} + break; + + case 51: // Resume SD Print + resumePrint(); + SEND_TXT_END("qpause.picc=28"); + break; + + case 52: // Stop SD print + //if (isPrintingFromMedia()) { + stopPrint(); + SEND_TXT_END("page prepare"); + //} + break; + + case 54: // A13 Select file + SelectFile(); + break; + + case 65: // Cool Down + if (!isPrinting()) coolDown(); + break; + + case 66: // Refresh SD + if (!isPrinting()) { + injectCommands_P(PSTR("M21")); + filenavigator.reset(); + } + break; + + case 56: // Set Fan, Flow, Print Speed + switch (nextion_command[4]) { + case 'S': setTargetFan_percent(atof(&nextion_command[5]), FAN0); break; + case 'P': setFeedrate_percent(atoi(&nextion_command[5])); break; + case 'F': setFlow_percent(atoi(&nextion_command[5]), getActiveTool()); break; + } + break; + + case 57: // Disable Motors + if (!isPrinting()) { + disable_all_steppers(); // from marlincore.h + SEND_TXT("tmppage.M117", "Motors disabled"); + } + break; + + case 58: // Load/Unload Filament + #if ENABLED(FILAMENT_LOAD_UNLOAD_GCODES) + if (canMove(getActiveTool())) { + switch (nextion_command[4]) { + case 'L': injectCommands_P(PSTR("M701")); break; + case 'U': injectCommands_P(PSTR("M702")); break; + } + } + else { + SEND_TXT("tmppage.M117", "Preheat first"); + SEND_TXT_END("page preheat"); + } + #else + SEND_TXT("tmppage.M117", "Filament loading disabled"); + #endif + break; + + case 63: // Preheat // Temps defined in configuration.h + #if PREHEAT_COUNT + if (!isPrinting()) switch (nextion_command[4]) { + // Preheat PLA + case 'P': + #if HAS_HEATED_BED + setTargetTemp_celsius(getMaterial_preset_B(0), BED); + #endif + setTargetTemp_celsius(getMaterial_preset_E(0), getActiveTool()); + break; + + // Preheat ABS + case 'A': + #if HAS_HEATED_BED + setTargetTemp_celsius(getMaterial_preset_B(1), BED); + #endif + setTargetTemp_celsius(getMaterial_preset_E(1), getActiveTool()); + break; + + // Preheat PETG + case 'G': + #if HAS_HEATED_BED + setTargetTemp_celsius(getMaterial_preset_B(2), BED); + #endif + setTargetTemp_celsius(getMaterial_preset_E(2), getActiveTool()); + break; + } + #else + SEND_TXT("tmppage.M117", "Preheat disabled"); + #endif + break; + } +} + +void NextionTFT::UpdateOnChange() { + const millis_t ms = millis(); + static millis_t next_event_ms = 0; + // tmppage Temperature + if (!WITHIN(last_degHotend0 - getActualTemp_celsius(E0), -0.2, 0.2) || !WITHIN(last_degTargetHotend0 - getTargetTemp_celsius(E0), -0.5, 0.5)) { + SEND_TEMP("tmppage.t0", ui8tostr3rj(getActualTemp_celsius(E0)), " / ", ui8tostr3rj(getTargetTemp_celsius(E0))); + last_degHotend0 = getActualTemp_celsius(E0); + last_degTargetHotend0 = getTargetTemp_celsius(E0); + } + + if (!WITHIN(last_degHotend1 - getActualTemp_celsius(E1), -0.2, 0.2) || !WITHIN(last_degTargetHotend1 - getTargetTemp_celsius(E1), -0.5, 0.5)) { + SEND_TEMP("tmppage.t1", ui8tostr3rj(getActualTemp_celsius(E1)), " / ", ui8tostr3rj(getTargetTemp_celsius(E1))); + last_degHotend1 = getActualTemp_celsius(E1); + last_degTargetHotend1 = getTargetTemp_celsius(E1); + } + + if (!WITHIN(last_degBed - getActualTemp_celsius(BED), -0.2, 0.2) || !WITHIN(last_degTargetBed - getTargetTemp_celsius(BED), -0.5, 0.5)) { + SEND_TEMP("tmppage.t2", ui8tostr3rj(getActualTemp_celsius(BED)), " / ", ui8tostr3rj(getTargetTemp_celsius(BED))); + last_degBed = getActualTemp_celsius(BED); + last_degTargetBed = getTargetTemp_celsius(BED); + } + + // tmppage Tool + if (last_active_extruder != getActiveTool()) { + SEND_VALasTXT("tmppage.tool", getActiveTool()); + last_active_extruder = getActiveTool(); + } + + // tmppage Fan Speed + if (last_fan_speed != getActualFan_percent(FAN0)) { + SEND_VALasTXT("tmppage.fan", ui8tostr3rj(getActualFan_percent(FAN0))); + last_fan_speed = getActualFan_percent(FAN0); + } + + // tmppage Print Speed + if (last_print_speed != getFeedrate_percent()) { + SEND_VALasTXT("tmppage.speed", ui8tostr3rj(getFeedrate_percent())); + last_print_speed = getFeedrate_percent(); + } + + // tmppage Flow + if (last_flow_speed != getFlowPercentage(getActiveTool())) { + SEND_VALasTXT("tmppage.flow", getFlowPercentage(getActiveTool())); + last_flow_speed = getFlowPercentage(getActiveTool()); + } + + // tmppage Progress + Layer + Time + if (isPrinting()) { + + if (ELAPSED(ms, next_event_ms)) { + next_event_ms = ms + 1000; + #if ENABLED(SHOW_REMAINING_TIME) + const uint32_t remaining = getProgress_seconds_remaining(); + char remaining_str[10]; + _format_time(remaining_str, remaining); + SEND_VALasTXT("tmppage.remaining", remaining_str); + #endif + const uint32_t elapsed = getProgress_seconds_elapsed(); + char elapsed_str[10]; + _format_time(elapsed_str, elapsed); + SEND_VALasTXT("tmppage.elapsed", elapsed_str); + } + + if (last_progress != getProgress_percent()) { + SEND_VALasTXT("tmppage.progress", ui8tostr3rj(getProgress_percent())); + last_progress = getProgress_percent(); + } + + if (last_get_axis_position_mmZ < getAxisPosition_mm(Z)) { + layer++; + SEND_VALasTXT("tmppage.layer", layer); + } + + if (last_get_axis_position_mmZ > getAxisPosition_mm(Z)) { + layer--; + SEND_VALasTXT("tmppage.layer", layer); + } + } + + // tmppage Axis + if (!WITHIN(last_get_axis_position_mmX - getAxisPosition_mm(X), -0.1, 0.1)) { + if (ELAPSED(ms, next_event_ms)) { + next_event_ms = ms + 30; + SEND_VALasTXT("tmppage.x", getAxisPosition_mm(X)); + last_get_axis_position_mmX = getAxisPosition_mm(X); + } + } + + if (!WITHIN(last_get_axis_position_mmY - getAxisPosition_mm(Y), -0.1, 0.1)) { + if (ELAPSED(ms, next_event_ms)) { + next_event_ms = ms + 30; + SEND_VALasTXT("tmppage.y", getAxisPosition_mm(Y)); + last_get_axis_position_mmY = getAxisPosition_mm(Y); + } + } + + if (!WITHIN(last_get_axis_position_mmZ - getAxisPosition_mm(Z), -0.1, 0.1)) { + SEND_VALasTXT("tmppage.z", getAxisPosition_mm(Z)); + last_get_axis_position_mmZ = getAxisPosition_mm(Z); + } + + // tmppage homed + if (last_homed != isPositionKnown()) { + SEND_VAL("tmppage.homed", isPositionKnown()); + last_homed = isPositionKnown(); + } + if (last_homedX != isAxisPositionKnown(X)) { + SEND_VAL("tmppage.homedx", isAxisPositionKnown(X)); + last_homedX = isAxisPositionKnown(X); + } + if (last_homedY != isAxisPositionKnown(Y)) { + SEND_VAL("tmppage.homedy", isAxisPositionKnown(Y)); + last_homedY = isAxisPositionKnown(Y); + } + if (last_homedZ != isAxisPositionKnown(Z)) { + SEND_VAL("tmppage.homedz", isAxisPositionKnown(Z)); + last_homedZ = isAxisPositionKnown(Z); + } + + // tmppage IDEX Mode + #if ENABLED(DUAL_X_CARRIAGE) + if (last_IDEX_Mode != getIDEX_Mode()) { + SEND_VAL("tmppage.idexmode", getIDEX_Mode()); + last_IDEX_Mode = getIDEX_Mode(); + } + #endif +} + +#endif // NEXTION_TFT diff --git a/Marlin/src/lcd/extui/lib/nextion/nextion_tft.h b/Marlin/src/lcd/extui/lib/nextion/nextion_tft.h new file mode 100644 index 0000000000..9197fcc2c6 --- /dev/null +++ b/Marlin/src/lcd/extui/lib/nextion/nextion_tft.h @@ -0,0 +1,62 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2021 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/* **************************************** + * lcd/extui/lib/nextion/nextion_tft.h + * **************************************** + * Extensible_UI implementation for Nextion + * https://github.com/Skorpi08 + * ***************************************/ + +#include "nextion_tft_defs.h" +#include "../../../../inc/MarlinConfigPre.h" +#include "../../ui_api.h" + +class NextionTFT { + private: + static uint8_t command_len; + static char nextion_command[MAX_CMND_LEN]; + static char selectedfile[MAX_PATH_LEN]; + + public: + NextionTFT(); + static void Startup(); + static void IdleLoop(); + static void PrinterKilled(PGM_P, PGM_P); + static void ConfirmationRequest(const char * const ); + static void StatusChange(const char * const ); + static void SendtoTFT(PGM_P); + static void UpdateOnChange(); + static void PrintFinished(); + static void PanelInfo(uint8_t); + + private: + static bool ReadTFTCommand(); + static void SendFileList(int8_t); + static void SelectFile(); + static void ProcessPanelRequest(); + static void PanelAction(uint8_t); + static void _format_time(char *, uint32_t); +}; + +extern NextionTFT nextion; diff --git a/Marlin/src/lcd/extui/lib/nextion/nextion_tft_defs.h b/Marlin/src/lcd/extui/lib/nextion/nextion_tft_defs.h new file mode 100644 index 0000000000..75f70fc985 --- /dev/null +++ b/Marlin/src/lcd/extui/lib/nextion/nextion_tft_defs.h @@ -0,0 +1,63 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2021 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/* **************************************** + * lcd/extui/lib/nextion/nextion_tft_defs.h + * **************************************** + * Extensible_UI implementation for Nextion + * https://github.com/Skorpi08 + * ***************************************/ + +#include "../../../../inc/MarlinConfigPre.h" + +//#define NEXDEBUGLEVEL 255 +#if NEXDEBUGLEVEL + // Bit-masks for selective debug: + enum NexDebugMask : uint8_t { + N_INFO = _BV(0), + N_ACTION = _BV(1), + N_FILE = _BV(2), + N_PANEL = _BV(3), + N_MARLIN = _BV(4), + N_SOME = _BV(5), + N_ALL = _BV(6) + }; + #define NEXDEBUG(M) (((M) & NEXDEBUGLEVEL) == M) // Debug flag macro +#else + #define NEXDEBUG(M) false +#endif + +#define MAX_FOLDER_DEPTH 4 // Limit folder depth TFT has a limit for the file path +#define MAX_CMND_LEN 16 * MAX_FOLDER_DEPTH // Maximum Length for a Panel command +#define MAX_PATH_LEN 16 * MAX_FOLDER_DEPTH // Maximum number of characters in a SD file path + + // TFT panel commands +#define msg_welcome MACHINE_NAME " Ready." + +#define SEND_TEMP(x,y,t,z) (nextion.SendtoTFT(PSTR(x)), nextion.SendtoTFT(PSTR(".txt=\"")), LCD_SERIAL.print(y), nextion.SendtoTFT(PSTR(t)), LCD_SERIAL.print(z), nextion.SendtoTFT(PSTR("\"\xFF\xFF\xFF"))) +#define SEND_VAL(x,y) (nextion.SendtoTFT(PSTR(x)), nextion.SendtoTFT(PSTR(".val=")), LCD_SERIAL.print(y), nextion.SendtoTFT(PSTR("\xFF\xFF\xFF"))) +#define SEND_TXT(x,y) (nextion.SendtoTFT(PSTR(x)), nextion.SendtoTFT(PSTR(".txt=\"")), nextion.SendtoTFT(PSTR(y)), nextion.SendtoTFT(PSTR("\"\xFF\xFF\xFF"))) +#define SEND_TXT_P(x,y) (nextion.SendtoTFT(PSTR(x)), nextion.SendtoTFT(PSTR(".txt=\"")), nextion.SendtoTFT(y), nextion.SendtoTFT(PSTR("\"\xFF\xFF\xFF"))) +#define SEND_VALasTXT(x,y) (nextion.SendtoTFT(PSTR(x)), nextion.SendtoTFT(PSTR(".txt=\"")), LCD_SERIAL.print(y), nextion.SendtoTFT(PSTR("\"\xFF\xFF\xFF"))) +#define SEND_TXT_END(x) (nextion.SendtoTFT(PSTR(x)), nextion.SendtoTFT(PSTR("\xFF\xFF\xFF"))) +#define SEND_PCO2(x,y,z) (nextion.SendtoTFT(PSTR(x)), LCD_SERIAL.print(y), nextion.SendtoTFT(PSTR(".pco=")), nextion.SendtoTFT(PSTR(z)), nextion.SendtoTFT(PSTR("\xFF\xFF\xFF"))) diff --git a/Marlin/src/lcd/extui/nextion_lcd.cpp b/Marlin/src/lcd/extui/nextion_lcd.cpp new file mode 100644 index 0000000000..fa45f4ef51 --- /dev/null +++ b/Marlin/src/lcd/extui/nextion_lcd.cpp @@ -0,0 +1,117 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2021 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ + +/** + * lcd/extui/nextion_lcd.cpp + * + * Nextion TFT support for Marlin + */ + +#include "../../inc/MarlinConfigPre.h" + +#if ENABLED(NEXTION_TFT) + +#include "ui_api.h" +#include "lib/nextion/nextion_tft.h" + +namespace ExtUI { + + void onStartup() { nextion.Startup(); } + void onIdle() { nextion.IdleLoop(); } + void onPrinterKilled(PGM_P const error, PGM_P const component) { nextion.PrinterKilled(error,component); } + void onMediaInserted() {} + void onMediaError() {} + void onMediaRemoved() {} + void onPlayTone(const uint16_t frequency, const uint16_t duration) {} + void onPrintTimerStarted() {} + void onPrintTimerPaused() {} + void onPrintTimerStopped() {} + void onFilamentRunout(const extruder_t) {} + void onUserConfirmRequired(const char * const msg) { nextion.ConfirmationRequest(msg); } + void onStatusChanged(const char * const msg) { nextion.StatusChange(msg); } + + void onHomingStart() {} + void onHomingComplete() {} + void onPrintFinished() { nextion.PrintFinished(); } + + void onFactoryReset() {} + + void onStoreSettings(char *buff) { + // Called when saving to EEPROM (i.e. M500). If the ExtUI needs + // permanent data to be stored, it can write up to eeprom_data_size bytes + // into buff. + + // Example: + // static_assert(sizeof(myDataStruct) <= ExtUI::eeprom_data_size); + // memcpy(buff, &myDataStruct, sizeof(myDataStruct)); + } + + void onLoadSettings(const char *buff) { + // Called while loading settings from EEPROM. If the ExtUI + // needs to retrieve data, it should copy up to eeprom_data_size bytes + // from buff + + // Example: + // static_assert(sizeof(myDataStruct) <= ExtUI::eeprom_data_size); + // memcpy(&myDataStruct, buff, sizeof(myDataStruct)); + } + + void onConfigurationStoreWritten(bool success) { + // Called after the entire EEPROM has been written, + // whether successful or not. + } + + void onConfigurationStoreRead(bool success) { + // Called after the entire EEPROM has been read, + // whether successful or not. + } + + #if HAS_MESH + void onMeshLevelingStart() {} + + void onMeshUpdate(const int8_t xpos, const int8_t ypos, const float zval) { + // Called when any mesh points are updated + } + + void onMeshUpdate(const int8_t xpos, const int8_t ypos, const ExtUI::probe_state_t state) { + // Called to indicate a special condition + } + #endif + + #if ENABLED(POWER_LOSS_RECOVERY) + void onPowerLossResume() { + // Called on resume from power-loss + } + #endif + + #if HAS_PID_HEATING + void onPidTuning(const result_t rst) { + // Called for temperature PID tuning result + nextion.PanelInfo(37); + } + #endif + + void onSteppersDisabled() {} + void onSteppersEnabled() {} +} + +#endif // NEXTION_TFT diff --git a/Marlin/src/lcd/extui/ui_api.cpp b/Marlin/src/lcd/extui/ui_api.cpp index d83b921648..73e5bc092d 100644 --- a/Marlin/src/lcd/extui/ui_api.cpp +++ b/Marlin/src/lcd/extui/ui_api.cpp @@ -587,13 +587,11 @@ namespace ExtUI { void setAxisMaxAcceleration_mm_s2(const float &value, const axis_t axis) { planner.set_max_acceleration(axis, value); - planner.reset_acceleration_rates(); } void setAxisMaxAcceleration_mm_s2(const float &value, const extruder_t extruder) { UNUSED_E(extruder); planner.set_max_acceleration(E_AXIS_N(extruder - E0), value); - planner.reset_acceleration_rates(); } #if HAS_FILAMENT_SENSOR @@ -653,6 +651,17 @@ namespace ExtUI { void setAxisMaxJerk_mm_s(const float &value, const extruder_t) { planner.set_max_jerk(E_AXIS, value); } #endif + #if ENABLED(DUAL_X_CARRIAGE) + uint8_t getIDEX_Mode() { return dual_x_carriage_mode; } + #endif + + #if PREHEAT_COUNT + uint16_t getMaterial_preset_E(const uint16_t index) { return ui.material_preset[index].hotend_temp; } + #if HAS_HEATED_BED + uint16_t getMaterial_preset_B(const uint16_t index) { return ui.material_preset[index].bed_temp; } + #endif + #endif + feedRate_t getFeedrate_mm_s() { return feedrate_mm_s; } int16_t getFlowPercentage(const extruder_t extr) { return planner.flow_percentage[extr]; } feedRate_t getMinFeedrate_mm_s() { return planner.settings.min_feedrate_mm_s; } @@ -665,8 +674,8 @@ namespace ExtUI { void setMinFeedrate_mm_s(const feedRate_t fr) { planner.settings.min_feedrate_mm_s = fr; } void setMinTravelFeedrate_mm_s(const feedRate_t fr) { planner.settings.min_travel_feedrate_mm_s = fr; } void setPrintingAcceleration_mm_s2(const float &acc) { planner.settings.acceleration = acc; } - void setRetractAcceleration_mm_s2(const float &acc) { planner.settings.retract_acceleration = acc; } - void setTravelAcceleration_mm_s2(const float &acc) { planner.settings.travel_acceleration = acc; } + void setRetractAcceleration_mm_s2(const float &acc) { planner.settings.retract_acceleration = acc; } + void setTravelAcceleration_mm_s2(const float &acc) { planner.settings.travel_acceleration = acc; } #if ENABLED(BABYSTEPPING) diff --git a/Marlin/src/lcd/extui/ui_api.h b/Marlin/src/lcd/extui/ui_api.h index 701bf9eb54..380d311517 100644 --- a/Marlin/src/lcd/extui/ui_api.h +++ b/Marlin/src/lcd/extui/ui_api.h @@ -139,6 +139,17 @@ namespace ExtUI { uint32_t getProgress_seconds_elapsed(); + #if PREHEAT_COUNT + uint16_t getMaterial_preset_E(const uint16_t); + #if HAS_HEATED_BED + uint16_t getMaterial_preset_B(const uint16_t); + #endif + #endif + + #if ENABLED(DUAL_X_CARRIAGE) + uint8_t getIDEX_Mode(); + #endif + #if ENABLED(SHOW_REMAINING_TIME) inline uint32_t getProgress_seconds_remaining() { return ui.get_remaining_time(); } #endif @@ -171,6 +182,7 @@ namespace ExtUI { #endif #if ENABLED(PRINTCOUNTER) + char* getFailedPrints_str(char buffer[21]); char* getTotalPrints_str(char buffer[21]); char* getFinishedPrints_str(char buffer[21]); char* getTotalPrintTime_str(char buffer[21]); diff --git a/Marlin/src/lcd/menu/menu_custom.cpp b/Marlin/src/lcd/menu/menu_custom.cpp index f3f946883f..cc1a8a6e80 100644 --- a/Marlin/src/lcd/menu/menu_custom.cpp +++ b/Marlin/src/lcd/menu/menu_custom.cpp @@ -46,7 +46,20 @@ void _lcd_user_gcode(PGM_P const cmd) { void menu_user() { START_MENU(); BACK_ITEM(MSG_MAIN); - #define USER_ITEM(N) ACTION_ITEM_P(PSTR(USER_DESC_##N), []{ _lcd_user_gcode(PSTR(USER_GCODE_##N _DONE_SCRIPT)); }); + + #define GCODE_LAMBDA(N) []{ _lcd_user_gcode(PSTR(USER_GCODE_##N _DONE_SCRIPT)); } + #define _USER_ITEM(N) ACTION_ITEM_P(PSTR(USER_DESC_##N), GCODE_LAMBDA(N)); + #define _USER_ITEM_CONFIRM(N) \ + SUBMENU_P(PSTR(USER_DESC_##N), []{ \ + MenuItem_confirm::confirm_screen( \ + GCODE_LAMBDA(N), \ + ui.goto_previous_screen, \ + PSTR(USER_DESC_##N "?") \ + ); \ + }) + + #define USER_ITEM(N) do{ if (ENABLED(USER_CONFIRM_##N)) _USER_ITEM_CONFIRM(N); else _USER_ITEM(N); }while(0) + #if HAS_USER_ITEM(1) USER_ITEM(1); #endif diff --git a/Marlin/src/lcd/menu/menu_main.cpp b/Marlin/src/lcd/menu/menu_main.cpp index 1e864e35be..d19e236a84 100644 --- a/Marlin/src/lcd/menu/menu_main.cpp +++ b/Marlin/src/lcd/menu/menu_main.cpp @@ -211,11 +211,13 @@ void menu_main() { SUBMENU(MSG_CONFIGURATION, menu_configuration); #if ENABLED(CUSTOM_USER_MENUS) - #ifdef CUSTOM_USER_MENU_TITLE - SUBMENU_P(PSTR(CUSTOM_USER_MENU_TITLE), menu_user); - #else - SUBMENU(MSG_USER_MENU, menu_user); - #endif + if (TERN1(CUSTOM_MENU_ONLY_IDLE, !busy)) { + #ifdef CUSTOM_USER_MENU_TITLE + SUBMENU_P(PSTR(CUSTOM_USER_MENU_TITLE), menu_user); + #else + SUBMENU(MSG_USER_MENU, menu_user); + #endif + } #endif #if ENABLED(ADVANCED_PAUSE_FEATURE) diff --git a/Marlin/src/module/planner.cpp b/Marlin/src/module/planner.cpp index dd87a0d24d..594671f87a 100644 --- a/Marlin/src/module/planner.cpp +++ b/Marlin/src/module/planner.cpp @@ -1248,32 +1248,6 @@ void Planner::recalculate() { recalculate_trapezoids(); } -#if ENABLED(AUTOTEMP) - - void Planner::getHighESpeed() { - static float oldt = 0; - - if (!autotemp_enabled) return; - if (thermalManager.degTargetHotend(0) + 2 < autotemp_min) return; // probably temperature set to zero. - - float high = 0.0; - for (uint8_t b = block_buffer_tail; b != block_buffer_head; b = next_block_index(b)) { - block_t* block = &block_buffer[b]; - if (block->steps.x || block->steps.y || block->steps.z) { - const float se = (float)block->steps.e / block->step_event_count * SQRT(block->nominal_speed_sqr); // mm/sec; - NOLESS(high, se); - } - } - - float t = autotemp_min + high * autotemp_factor; - LIMIT(t, autotemp_min, autotemp_max); - if (t < oldt) t = t * (1 - float(AUTOTEMP_OLDWEIGHT)) + oldt * float(AUTOTEMP_OLDWEIGHT); - oldt = t; - thermalManager.setTargetHotend(t, 0); - } - -#endif // AUTOTEMP - /** * Maintain fans, paste extruder pressure, */ @@ -1398,6 +1372,72 @@ void Planner::check_axes_activity() { #endif } +#if ENABLED(AUTOTEMP) + + #if ENABLED(AUTOTEMP_PROPORTIONAL) + void Planner::_autotemp_update_from_hotend() { + const int16_t target = thermalManager.degTargetHotend(active_extruder); + autotemp_min = target + AUTOTEMP_MIN_P; + autotemp_max = target + AUTOTEMP_MAX_P; + } + #endif + + /** + * Called after changing tools to: + * - Reset or re-apply the default proportional autotemp factor. + * - Enable autotemp if the factor is non-zero. + */ + void Planner::autotemp_update() { + _autotemp_update_from_hotend(); + autotemp_factor = TERN(AUTOTEMP_PROPORTIONAL, AUTOTEMP_FACTOR_P, 0); + autotemp_enabled = autotemp_factor != 0; + } + + /** + * Called by the M104/M109 commands after setting Hotend Temperature + * + */ + void Planner::autotemp_M104_M109() { + _autotemp_update_from_hotend(); + + if (parser.seenval('S')) autotemp_min = parser.value_celsius(); + if (parser.seenval('B')) autotemp_max = parser.value_celsius(); + + // When AUTOTEMP_PROPORTIONAL is enabled, F0 disables autotemp. + // Normally, leaving off F also disables autotemp. + autotemp_factor = parser.seen('F') ? parser.value_float() : TERN(AUTOTEMP_PROPORTIONAL, AUTOTEMP_FACTOR_P, 0); + autotemp_enabled = autotemp_factor != 0; + } + + /** + * Called every so often to adjust the hotend target temperature + * based on the extrusion speed, which is calculated from the blocks + * currently in the planner. + */ + void Planner::getHighESpeed() { + static float oldt = 0; + + if (!autotemp_enabled) return; + if (thermalManager.degTargetHotend(active_extruder) < autotemp_min - 2) return; // Below the min? + + float high = 0.0; + for (uint8_t b = block_buffer_tail; b != block_buffer_head; b = next_block_index(b)) { + block_t* block = &block_buffer[b]; + if (block->steps.x || block->steps.y || block->steps.z) { + const float se = (float)block->steps.e / block->step_event_count * SQRT(block->nominal_speed_sqr); // mm/sec; + NOLESS(high, se); + } + } + + float t = autotemp_min + high * autotemp_factor; + LIMIT(t, autotemp_min, autotemp_max); + if (t < oldt) t *= (1.0f - (AUTOTEMP_OLDWEIGHT)) + oldt * (AUTOTEMP_OLDWEIGHT); + oldt = t; + thermalManager.setTargetHotend(t, active_extruder); + } + +#endif + #if DISABLED(NO_VOLUMETRICS) /** @@ -2959,13 +2999,17 @@ void Planner::reset_acceleration_rates() { TERN_(HAS_LINEAR_E_JERK, recalculate_max_e_jerk()); } -// Recalculate position, steps_to_mm if settings.axis_steps_per_mm changes! +/** + * Recalculate 'position' and 'steps_to_mm'. + * Must be called whenever settings.axis_steps_per_mm changes! + */ void Planner::refresh_positioning() { LOOP_XYZE_N(i) steps_to_mm[i] = 1.0f / settings.axis_steps_per_mm[i]; set_position_mm(current_position); reset_acceleration_rates(); } +// Apply limits to a variable and give a warning if the value was out of range inline void limit_and_warn(float &val, const uint8_t axis, PGM_P const setting_name, const xyze_float_t &max_limit) { const uint8_t lim_axis = axis > E_AXIS ? E_AXIS : axis; const float before = val; @@ -2978,7 +3022,14 @@ inline void limit_and_warn(float &val, const uint8_t axis, PGM_P const setting_n } } -void Planner::set_max_acceleration(const uint8_t axis, float targetValue) { +/** + * For the specified 'axis' set the Maximum Acceleration to the given value (mm/s^2) + * The value may be limited with warning feedback, if configured. + * Calls reset_acceleration_rates to precalculate planner terms in steps. + * + * This hard limit is applied as a block is being added to the planner queue. + */ +void Planner::set_max_acceleration(const uint8_t axis, float inMaxAccelMMS2) { #if ENABLED(LIMITED_MAX_ACCEL_EDITING) #ifdef MAX_ACCEL_EDIT_VALUES constexpr xyze_float_t max_accel_edit = MAX_ACCEL_EDIT_VALUES; @@ -2987,15 +3038,21 @@ void Planner::set_max_acceleration(const uint8_t axis, float targetValue) { constexpr xyze_float_t max_accel_edit = DEFAULT_MAX_ACCELERATION; const xyze_float_t max_acc_edit_scaled = max_accel_edit * 2; #endif - limit_and_warn(targetValue, axis, PSTR("Acceleration"), max_acc_edit_scaled); + limit_and_warn(inMaxAccelMMS2, axis, PSTR("Acceleration"), max_acc_edit_scaled); #endif - settings.max_acceleration_mm_per_s2[axis] = targetValue; + settings.max_acceleration_mm_per_s2[axis] = inMaxAccelMMS2; // Update steps per s2 to agree with the units per s2 (since they are used in the planner) reset_acceleration_rates(); } -void Planner::set_max_feedrate(const uint8_t axis, float targetValue) { +/** + * For the specified 'axis' set the Maximum Feedrate to the given value (mm/s) + * The value may be limited with warning feedback, if configured. + * + * This hard limit is applied as a block is being added to the planner queue. + */ +void Planner::set_max_feedrate(const uint8_t axis, float inMaxFeedrateMMS) { #if ENABLED(LIMITED_MAX_FR_EDITING) #ifdef MAX_FEEDRATE_EDIT_VALUES constexpr xyze_float_t max_fr_edit = MAX_FEEDRATE_EDIT_VALUES; @@ -3004,13 +3061,20 @@ void Planner::set_max_feedrate(const uint8_t axis, float targetValue) { constexpr xyze_float_t max_fr_edit = DEFAULT_MAX_FEEDRATE; const xyze_float_t max_fr_edit_scaled = max_fr_edit * 2; #endif - limit_and_warn(targetValue, axis, PSTR("Feedrate"), max_fr_edit_scaled); + limit_and_warn(inMaxFeedrateMMS, axis, PSTR("Feedrate"), max_fr_edit_scaled); #endif - settings.max_feedrate_mm_s[axis] = targetValue; + settings.max_feedrate_mm_s[axis] = inMaxFeedrateMMS; } -void Planner::set_max_jerk(const AxisEnum axis, float targetValue) { - #if HAS_CLASSIC_JERK +#if HAS_CLASSIC_JERK + + /** + * For the specified 'axis' set the Maximum Jerk (instant change) to the given value (mm/s) + * The value may be limited with warning feedback, if configured. + * + * This hard limit is applied (to the block start speed) as the block is being added to the planner queue. + */ + void Planner::set_max_jerk(const AxisEnum axis, float inMaxJerkMMS) { #if ENABLED(LIMITED_JERK_EDITING) constexpr xyze_float_t max_jerk_edit = #ifdef MAX_JERK_EDIT_VALUES @@ -3020,13 +3084,12 @@ void Planner::set_max_jerk(const AxisEnum axis, float targetValue) { (DEFAULT_ZJERK) * 2, (DEFAULT_EJERK) * 2 } #endif ; - limit_and_warn(targetValue, axis, PSTR("Jerk"), max_jerk_edit); + limit_and_warn(inMaxJerkMMS, axis, PSTR("Jerk"), max_jerk_edit); #endif - max_jerk[axis] = targetValue; - #else - UNUSED(axis); UNUSED(targetValue); - #endif -} + max_jerk[axis] = inMaxJerkMMS; + } + +#endif #if HAS_WIRED_LCD @@ -3069,33 +3132,3 @@ void Planner::set_max_jerk(const AxisEnum axis, float targetValue) { } #endif - -#if ENABLED(AUTOTEMP) - -void Planner::autotemp_update() { - #if ENABLED(AUTOTEMP_PROPORTIONAL) - const int16_t target = thermalManager.degTargetHotend(active_extruder); - autotemp_min = target + AUTOTEMP_MIN_P; - autotemp_max = target + AUTOTEMP_MAX_P; - #endif - autotemp_factor = TERN(AUTOTEMP_PROPORTIONAL, AUTOTEMP_FACTOR_P, 0); - autotemp_enabled = autotemp_factor != 0; -} - - void Planner::autotemp_M104_M109() { - - #if ENABLED(AUTOTEMP_PROPORTIONAL) - const int16_t target = thermalManager.degTargetHotend(active_extruder); - autotemp_min = target + AUTOTEMP_MIN_P; - autotemp_max = target + AUTOTEMP_MAX_P; - #endif - - if (parser.seenval('S')) autotemp_min = parser.value_celsius(); - if (parser.seenval('B')) autotemp_max = parser.value_celsius(); - - // When AUTOTEMP_PROPORTIONAL is enabled, F0 disables autotemp. - // Normally, leaving off F also disables autotemp. - autotemp_factor = parser.seen('F') ? parser.value_float() : TERN(AUTOTEMP_PROPORTIONAL, AUTOTEMP_FACTOR_P, 0); - autotemp_enabled = autotemp_factor != 0; - } -#endif diff --git a/Marlin/src/module/planner.h b/Marlin/src/module/planner.h index b7ff0ee932..7ebba1e342 100644 --- a/Marlin/src/module/planner.h +++ b/Marlin/src/module/planner.h @@ -460,12 +460,27 @@ class Planner { * Static (class) Methods */ + // Recalculate steps/s^2 accelerations based on mm/s^2 settings static void reset_acceleration_rates(); - static void refresh_positioning(); - static void set_max_acceleration(const uint8_t axis, float targetValue); - static void set_max_feedrate(const uint8_t axis, float targetValue); - static void set_max_jerk(const AxisEnum axis, float targetValue); + /** + * Recalculate 'position' and 'steps_to_mm'. + * Must be called whenever settings.axis_steps_per_mm changes! + */ + static void refresh_positioning(); + + // For an axis set the Maximum Acceleration in mm/s^2 + static void set_max_acceleration(const uint8_t axis, float inMaxAccelMMS2); + + // For an axis set the Maximum Feedrate in mm/s + static void set_max_feedrate(const uint8_t axis, float inMaxFeedrateMMS); + + // For an axis set the Maximum Jerk (instant change) in mm/s + #if HAS_CLASSIC_JERK + static void set_max_jerk(const AxisEnum axis, float inMaxJerkMMS); + #else + static inline void set_max_jerk(const AxisEnum, const float&) {} + #endif #if EXTRUDERS FORCE_INLINE static void refresh_e_factor(const uint8_t e) { @@ -883,9 +898,9 @@ class Planner { #if ENABLED(AUTOTEMP) static float autotemp_min, autotemp_max, autotemp_factor; static bool autotemp_enabled; - static void getHighESpeed(); - static void autotemp_M104_M109(); static void autotemp_update(); + static void autotemp_M104_M109(); + static void getHighESpeed(); #endif #if HAS_LINEAR_E_JERK @@ -898,6 +913,14 @@ class Planner { private: + #if ENABLED(AUTOTEMP) + #if ENABLED(AUTOTEMP_PROPORTIONAL) + static void _autotemp_update_from_hotend(); + #else + static inline void _autotemp_update_from_hotend() {} + #endif + #endif + /** * Get the index of the next / previous block in the ring buffer */ diff --git a/Marlin/src/pins/pins.h b/Marlin/src/pins/pins.h index b8cf695fb5..58a87f2313 100644 --- a/Marlin/src/pins/pins.h +++ b/Marlin/src/pins/pins.h @@ -447,6 +447,8 @@ #include "sam/pins_PRINTRBOARD_G2.h" // SAM3X8C env:DUE_USB #elif MB(CNCONTROLS_15D) #include "sam/pins_CNCONTROLS_15D.h" // SAM3X8E env:DUE env:DUE_USB +#elif MB(KRATOS32) + #include "sam/pins_KRATOS32.h" // SAM3X8E env:DUE env:DUE_USB // // STM32 ARM Cortex-M0 diff --git a/Marlin/src/pins/sam/pins_KRATOS32.h b/Marlin/src/pins/sam/pins_KRATOS32.h new file mode 100644 index 0000000000..f429e56347 --- /dev/null +++ b/Marlin/src/pins/sam/pins_KRATOS32.h @@ -0,0 +1,179 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2021 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * KRATOS32 + */ + +#include "env_validate.h" + +#define BOARD_INFO_NAME "K.3D KRATOS32" + +// +// EEPROM +// +#if EITHER(NO_EEPROM_SELECTED, I2C_EEPROM) + #define I2C_EEPROM + #define MARLIN_EEPROM_SIZE 0x1F400 // 16KB +#endif + +// +// Servos +// +#define SERVO0_PIN 6 +#define SERVO1_PIN 5 +#define SERVO2_PIN 39 +#define SERVO3_PIN 40 // CAMERA_PIN (extended to the top of the LCD module) +#define SERVO4_PIN 45 // FIL_RUNOUT_PIN + +// +// Limit Switches +// +#define X_MIN_PIN 28 +#define X_MAX_PIN 34 +#define Y_MIN_PIN 30 +#define Y_MAX_PIN 36 +#define Z_MIN_PIN 32 +#define Z_MAX_PIN 38 + +// +// Steppers +// +#define X_STEP_PIN 24 +#define X_DIR_PIN 23 +#define X_ENABLE_PIN 26 +#ifndef X_CS_PIN + #define X_CS_PIN 25 +#endif + +#define Y_STEP_PIN 17 +#define Y_DIR_PIN 16 +#define Y_ENABLE_PIN 22 +#ifndef Y_CS_PIN + #define Y_CS_PIN 27 +#endif + +#define Z_STEP_PIN 2 +#define Z_DIR_PIN 3 +#define Z_ENABLE_PIN 15 +#ifndef Z_CS_PIN + #define Z_CS_PIN 29 +#endif + +#define E0_STEP_PIN 61 +#define E0_DIR_PIN 60 +#define E0_ENABLE_PIN 62 +#ifndef E0_CS_PIN + #define E0_CS_PIN 31 +#endif + +#define E1_STEP_PIN 64 +#define E1_DIR_PIN 63 +#define E1_ENABLE_PIN 65 +#ifndef E1_CS_PIN + #define E1_CS_PIN 37 +#endif + +#define E2_STEP_PIN 68 +#define E2_DIR_PIN 67 +#define E2_ENABLE_PIN 69 +#ifndef E2_CS_PIN + #define E2_CS_PIN 35 +#endif + +#define E3_STEP_PIN 51 +#define E3_DIR_PIN 53 +#define E3_ENABLE_PIN 49 +#ifndef E3_CS_PIN + #define E3_CS_PIN 33 +#endif + +// +// Temperature Sensors +// +#define TEMP_0_PIN 0 // Analog Input +#define TEMP_1_PIN 1 // Analog Input +#define TEMP_2_PIN 2 // Analog Input +#define TEMP_3_PIN 3 // Analog Input +#define TEMP_BED_PIN 4 // Analog Input + +// +// Heaters / Fans +// +#define HEATER_0_PIN 13 +#define HEATER_1_PIN 12 +#define HEATER_2_PIN 11 +#define HEATER_3_PIN 10 +#define HEATER_BED_PIN 7 // BED + +#ifndef FAN_PIN + #define FAN_PIN 9 +#endif +#define FAN1_PIN 8 + +// +// Misc. Functions +// +#ifndef FIL_RUNOUT_PIN + #define FIL_RUNOUT_PIN 45 // SERVO4_PIN +#endif + +#ifndef PS_ON_PIN + #define PS_ON_PIN 59 +#endif + +// +// LCD / Controller +// +#if HAS_WIRED_LCD + + #define BTN_EN1 48 + #define BTN_EN2 50 + #define BTN_ENC 46 + + #define SDSS 4 + #define SD_DETECT_PIN 14 + + #define BEEPER_PIN 41 + #define KILL_PIN 66 + + #if IS_RRD_FG_SC + + #define LCD_PINS_RS 42 + #define LCD_PINS_ENABLE 43 + #define LCD_PINS_D4 44 + + #define BTN_BACK 52 + + #elif ENABLED(K3D_242_OLED_CONTROLLER) + + #define LCD_PINS_DC 44 + #define LCD_PINS_RS 42 + #define DOGLCD_CS 52 + #define DOGLCD_MOSI 43 + #define DOGLCD_SCK 47 + #define DOGLCD_A0 LCD_PINS_DC + + #endif + +#endif // HAS_WIRED_LCD diff --git a/Marlin/src/pins/sanguino/pins_MELZI_V2.h b/Marlin/src/pins/sanguino/pins_MELZI_V2.h index 275498d558..e0369923c7 100644 --- a/Marlin/src/pins/sanguino/pins_MELZI_V2.h +++ b/Marlin/src/pins/sanguino/pins_MELZI_V2.h @@ -29,7 +29,7 @@ #define BOARD_ST7920_DELAY_1 DELAY_NS(0) #endif #ifndef BOARD_ST7920_DELAY_2 - #define BOARD_ST7920_DELAY_2 DELAY_NS(188) + #define BOARD_ST7920_DELAY_2 DELAY_NS(400) #endif #ifndef BOARD_ST7920_DELAY_3 #define BOARD_ST7920_DELAY_3 DELAY_NS(0) diff --git a/Marlin/src/pins/stm32f4/pins_BTT_SKR_PRO_common.h b/Marlin/src/pins/stm32f4/pins_BTT_SKR_PRO_common.h index 863429f2a2..01ba3d72f6 100644 --- a/Marlin/src/pins/stm32f4/pins_BTT_SKR_PRO_common.h +++ b/Marlin/src/pins/stm32f4/pins_BTT_SKR_PRO_common.h @@ -441,10 +441,10 @@ // Alter timing for graphical display #if HAS_MARLINUI_U8GLIB #ifndef BOARD_ST7920_DELAY_1 - #define BOARD_ST7920_DELAY_1 DELAY_NS(96) + #define BOARD_ST7920_DELAY_1 DELAY_NS(125) #endif #ifndef BOARD_ST7920_DELAY_2 - #define BOARD_ST7920_DELAY_2 DELAY_NS(48) + #define BOARD_ST7920_DELAY_2 DELAY_NS(90) #endif #ifndef BOARD_ST7920_DELAY_3 #define BOARD_ST7920_DELAY_3 DELAY_NS(600) diff --git a/buildroot/bin/mftest b/buildroot/bin/mftest index d769ff8cb8..4cecf4f3a5 100755 --- a/buildroot/bin/mftest +++ b/buildroot/bin/mftest @@ -30,7 +30,6 @@ OPTIONS -v --verbose Extra output for debugging. env shortcuts: tree due esp lin lpc|lpc8 lpc9 m128 m256|mega stm|f1 f4 f7 s6 teensy|t31|t32 t35|t36 t40|t41 - " } @@ -58,47 +57,48 @@ while getopts 'abhmruvyn:t:-:' OFLAG; do h) EXIT_USAGE=1 ;; m) USE_MAKE=1 ; bugout "Using make with Docker..." ;; n) case "$OPTARG" in - *[!0-9]*) perror "option requires a number" $OFLAG ; EXIT_USAGE=1 ;; + *[!0-9]*) perror "option requires a number" $OFLAG ; EXIT_USAGE=2 ;; *) CHOICE="$OPTARG" ; bugout "Got a number: $CHOICE" ;; esac ;; - r) REBUILD=1 ; bugout "Rebuilding previous..." ;; + r) REBUILD=1 ; bugout "Rebuilding previous..." ;; t) TESTENV="$OPTARG" ; bugout "Got a target: $TESTENV" ;; - u) AUTO_BUILD=2 ; bugout "Auto-Upload target..." ;; + u) AUTO_BUILD=2 ; bugout "Auto-Upload target..." ;; v) DEBUG=1 ; bugout "Debug ON" ;; - y) BUILD_YES='Y' ; bugout "Build will initiate..." ;; + y) BUILD_YES='Y' ; bugout "Build will initiate..." ;; -) IFS="=" read -r ONAM OVAL <<< "$OPTARG" case "$ONAM" in help) [[ -z "$OVAL" ]] || perror "option can't take value $OVAL" $ONAM ; EXIT_USAGE=1 ;; autobuild) AUTO_BUILD=1 ; bugout "Auto-Build target..." ;; autoupload) AUTO_BUILD=2 ; bugout "Auto-Upload target..." ;; env) case "$OVAL" in - '') perror "option requires a value" $ONAM ; EXIT_USAGE=1 ;; + '') perror "option requires a value" $ONAM ; EXIT_USAGE=2 ;; *) TESTENV="$OVAL" ; bugout "Got a target: $TESTENV" ;; esac ;; num) case "$OVAL" in [0-9]+) CHOICE="$OVAL" ; bugout "Got a number: $CHOICE" ;; - *) perror "option requires a value" $ONAM ; EXIT_USAGE=1 ;; + *) perror "option requires a value" $ONAM ; EXIT_USAGE=2 ;; esac ;; - rebuild) REBUILD=1 ; bugout "Rebuilding previous..." ;; - make) USE_MAKE=1 ; bugout "Using make with Docker..." ;; -debug|verbose) DEBUG=1 ; bugout "Debug ON" ;; + rebuild) REBUILD=1 ; bugout "Rebuilding previous..." ;; + make) USE_MAKE=1 ; bugout "Using make with Docker..." ;; +debug|verbose) DEBUG=1 ; bugout "Debug ON" ;; build) case "$OVAL" in ''|y|yes) BUILD_YES='Y' ;; n|no) BUILD_YES='N' ;; - *) perror "option value must be y, n, yes, or no" $ONAM ; EXIT_USAGE=1 ;; + *) perror "option value must be y, n, yes, or no" $ONAM ; EXIT_USAGE=2 ;; esac bugout "Build will initiate? ($BUILD_YES)" ;; - *) perror "Unknown flag" "$OPTARG" ; EXIT_USAGE=1 ;; + *) perror "Unknown flag" "$OPTARG" ; EXIT_USAGE=2 ;; esac ;; + *) EXIT_USAGE=2 ;; esac done -((EXIT_USAGE)) && { usage ; exit 1 ; } +((EXIT_USAGE)) && { usage ; let EXIT_USAGE-- ; exit $EXIT_USAGE ; } if ((REBUILD)); then bugout "Rebuilding previous..." diff --git a/buildroot/share/PlatformIO/scripts/common-cxxflags.py b/buildroot/share/PlatformIO/scripts/common-cxxflags.py index 5c2bde7700..36704af283 100644 --- a/buildroot/share/PlatformIO/scripts/common-cxxflags.py +++ b/buildroot/share/PlatformIO/scripts/common-cxxflags.py @@ -22,10 +22,9 @@ def add_cpu_freq(): # # It will separe release and debug build folders. # It useful when we need keep two live versions: one debug, for debugging, -# other release, for flashing. +# other release, for flashing (when upload is not done automatically by jlink/stlink). # Without this, PIO will recompile everything twice for any small change. -# -if env.GetBuildType() == "debug": +if env.GetBuildType() == "debug" and env.get('UPLOAD_PROTOCOL') not in ['jlink', 'stlink']: env['BUILD_DIR'] = '$PROJECT_BUILD_DIR/$PIOENV/debug' # On some platform, F_CPU is a runtime variable. Since it's used to convert from ns diff --git a/buildroot/share/PlatformIO/scripts/common-dependencies.h b/buildroot/share/PlatformIO/scripts/common-dependencies.h index ed2f46abae..03fae56fdb 100644 --- a/buildroot/share/PlatformIO/scripts/common-dependencies.h +++ b/buildroot/share/PlatformIO/scripts/common-dependencies.h @@ -26,8 +26,6 @@ * Used by common-dependencies.py */ -#define NUM_SERIAL 1 // Normally provided by HAL/HAL.h - #include "../../../../Marlin/src/inc/MarlinConfig.h" // diff --git a/buildroot/share/PlatformIO/scripts/preflight-checks.py b/buildroot/share/PlatformIO/scripts/preflight-checks.py index 969a82aad2..2ad1562a31 100644 --- a/buildroot/share/PlatformIO/scripts/preflight-checks.py +++ b/buildroot/share/PlatformIO/scripts/preflight-checks.py @@ -2,33 +2,45 @@ # preflight-checks.py # Check for common issues prior to compiling # -import os,re +import os,re,sys Import("env") def get_envs_for_board(board): - if board.startswith("BOARD_"): - board = board[6:] - with open(os.path.join("Marlin", "src", "pins", "pins.h"),"r") as f: - board_found = "" - r=re.compile(r"if\s+MB\((.+)\)") - for line in f.readlines(): + with open(os.path.join("Marlin", "src", "pins", "pins.h"), "r") as file: + + if sys.platform == 'win32': + envregex = r"(?:env|win):" + elif sys.platform == 'darwin': + envregex = r"(?:env|mac|uni):" + elif sys.platform == 'linux': + envregex = r"(?:env|lin|uni):" + else: + envregex = r"(?:env):" + + r = re.compile(r"if\s+MB\((.+)\)") + if board.startswith("BOARD_"): + board = board[6:] + + for line in file: mbs = r.findall(line) - if mbs: - board_found = board if board in re.split(r",\s*", mbs[0]) else "" - if board_found and "#include " in line and "env:" in line: - return re.findall(r"env:\w+", line) + if mbs and board in re.split(r",\s*", mbs[0]): + line = file.readline() + found_envs = re.match(r"\s*#include .+" + envregex, line) + if found_envs: + envlist = re.findall(envregex + r"(\w+)", line) + return [ "env:"+s for s in envlist ] return [] -def check_envs(build_env, base_envs, config): - if build_env in base_envs: +def check_envs(build_env, board_envs, config): + if build_env in board_envs: return True ext = config.get(build_env, 'extends', default=None) if ext: if isinstance(ext, str): - return check_envs(ext, base_envs, config) + return check_envs(ext, board_envs, config) elif isinstance(ext, list): for ext_env in ext: - if check_envs(ext_env, base_envs, config): + if check_envs(ext_env, board_envs, config): return True return False @@ -44,13 +56,13 @@ if 'MOTHERBOARD' not in env['MARLIN_FEATURES']: build_env = env['PIOENV'] motherboard = env['MARLIN_FEATURES']['MOTHERBOARD'] -base_envs = get_envs_for_board(motherboard) +board_envs = get_envs_for_board(motherboard) config = env.GetProjectConfig() -result = check_envs("env:"+build_env, base_envs, config) +result = check_envs("env:"+build_env, board_envs, config) if not result: err = "Error: Build environment '%s' is incompatible with %s. Use one of these: %s" % \ - (build_env, motherboard, ",".join([e[4:] for e in base_envs if e.startswith("env:")])) + ( build_env, motherboard, ", ".join([ e[4:] for e in board_envs if e.startswith("env:") ]) ) raise SystemExit(err) # diff --git a/buildroot/share/scripts/gen-tft-image.py b/buildroot/share/scripts/gen-tft-image.py new file mode 100644 index 0000000000..d89245fea4 --- /dev/null +++ b/buildroot/share/scripts/gen-tft-image.py @@ -0,0 +1,64 @@ +#!/usr/bin/env python3 +# +# Marlin 3D Printer Firmware +# Copyright (c) 2021 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] +# +# Based on Sprinter and grbl. +# Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm +# +# This program is free software: you can redistribute it and/or modify +# it under the terms of the GNU General Public License as published by +# the Free Software Foundation, either version 3 of the License, or +# (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program. If not, see . +# + +# Generate Marlin TFT Images from bitmaps/PNG/JPG + +import sys,re,struct +from PIL import Image,ImageDraw + +def image2bin(image, output_file): + if output_file.endswith(('.c', '.cpp')): + f = open(output_file, 'wt') + is_cpp = True + f.write("const uint16_t image[%d] = {\n" % (image.size[1] * image.size[0])) + else: + f = open(output_file, 'wb') + is_cpp = False + pixs = image.load() + for y in range(image.size[1]): + for x in range(image.size[0]): + R = pixs[x, y][0] >> 3 + G = pixs[x, y][1] >> 2 + B = pixs[x, y][2] >> 3 + rgb = (R << 11) | (G << 5) | B + if is_cpp: + strHex = '0x{0:04X}, '.format(rgb) + f.write(strHex) + else: + f.write(struct.pack("B", (rgb & 0xFF))) + f.write(struct.pack("B", (rgb >> 8) & 0xFF)) + if is_cpp: + f.write("\n") + if is_cpp: + f.write("};\n") + f.close() + +if len(sys.argv) <= 2: + print("Utility to export a image in Marlin TFT friendly format.") + print("It will dump a raw bin RGB565 image or create a CPP file with an array of 16 bit image pixels.") + print("Usage: gen-tft-image.py INPUT_IMAGE.(png|bmp|jpg) OUTPUT_FILE.(cpp|bin)") + print("Author: rhapsodyv") + exit(1) + +output_img = sys.argv[2] +img = Image.open(sys.argv[1]) +image2bin(img, output_img) diff --git a/data/www/bootstrap.min.css b/buildroot/web-ui/data/www/bootstrap.min.css similarity index 100% rename from data/www/bootstrap.min.css rename to buildroot/web-ui/data/www/bootstrap.min.css diff --git a/data/www/bootstrap.min.js b/buildroot/web-ui/data/www/bootstrap.min.js similarity index 100% rename from data/www/bootstrap.min.js rename to buildroot/web-ui/data/www/bootstrap.min.js diff --git a/data/www/bootstrap4-toggle.min.js b/buildroot/web-ui/data/www/bootstrap4-toggle.min.js similarity index 100% rename from data/www/bootstrap4-toggle.min.js rename to buildroot/web-ui/data/www/bootstrap4-toggle.min.js diff --git a/data/www/chart.lineargauge.js b/buildroot/web-ui/data/www/chart.lineargauge.js similarity index 100% rename from data/www/chart.lineargauge.js rename to buildroot/web-ui/data/www/chart.lineargauge.js diff --git a/data/www/chart.min.js b/buildroot/web-ui/data/www/chart.min.js similarity index 100% rename from data/www/chart.min.js rename to buildroot/web-ui/data/www/chart.min.js diff --git a/data/www/filesaver.min.js b/buildroot/web-ui/data/www/filesaver.min.js similarity index 100% rename from data/www/filesaver.min.js rename to buildroot/web-ui/data/www/filesaver.min.js diff --git a/data/www/index-ie.html b/buildroot/web-ui/data/www/index-ie.html similarity index 100% rename from data/www/index-ie.html rename to buildroot/web-ui/data/www/index-ie.html diff --git a/data/www/index.html b/buildroot/web-ui/data/www/index.html similarity index 100% rename from data/www/index.html rename to buildroot/web-ui/data/www/index.html diff --git a/data/www/jquery-3.5.1.slim.min.js b/buildroot/web-ui/data/www/jquery-3.5.1.slim.min.js similarity index 100% rename from data/www/jquery-3.5.1.slim.min.js rename to buildroot/web-ui/data/www/jquery-3.5.1.slim.min.js diff --git a/data/www/jquery.browser.min.js b/buildroot/web-ui/data/www/jquery.browser.min.js similarity index 100% rename from data/www/jquery.browser.min.js rename to buildroot/web-ui/data/www/jquery.browser.min.js diff --git a/data/www/marlin-logo-dark.png b/buildroot/web-ui/data/www/marlin-logo-dark.png similarity index 100% rename from data/www/marlin-logo-dark.png rename to buildroot/web-ui/data/www/marlin-logo-dark.png diff --git a/data/www/marlinui.eot b/buildroot/web-ui/data/www/marlinui.eot similarity index 100% rename from data/www/marlinui.eot rename to buildroot/web-ui/data/www/marlinui.eot diff --git a/data/www/marlinui.svg b/buildroot/web-ui/data/www/marlinui.svg similarity index 100% rename from data/www/marlinui.svg rename to buildroot/web-ui/data/www/marlinui.svg diff --git a/data/www/marlinui.ttf b/buildroot/web-ui/data/www/marlinui.ttf similarity index 100% rename from data/www/marlinui.ttf rename to buildroot/web-ui/data/www/marlinui.ttf diff --git a/data/www/marlinui.woff b/buildroot/web-ui/data/www/marlinui.woff similarity index 100% rename from data/www/marlinui.woff rename to buildroot/web-ui/data/www/marlinui.woff diff --git a/data/www/moment.min.js b/buildroot/web-ui/data/www/moment.min.js similarity index 100% rename from data/www/moment.min.js rename to buildroot/web-ui/data/www/moment.min.js diff --git a/data/www/webmarlin-class.js b/buildroot/web-ui/data/www/webmarlin-class.js similarity index 100% rename from data/www/webmarlin-class.js rename to buildroot/web-ui/data/www/webmarlin-class.js diff --git a/data/www/webmarlin-font.css b/buildroot/web-ui/data/www/webmarlin-font.css similarity index 100% rename from data/www/webmarlin-font.css rename to buildroot/web-ui/data/www/webmarlin-font.css diff --git a/data/www/webmarlin.css b/buildroot/web-ui/data/www/webmarlin.css similarity index 100% rename from data/www/webmarlin.css rename to buildroot/web-ui/data/www/webmarlin.css diff --git a/data/www/webmarlin.js b/buildroot/web-ui/data/www/webmarlin.js similarity index 100% rename from data/www/webmarlin.js rename to buildroot/web-ui/data/www/webmarlin.js diff --git a/platformio.ini b/platformio.ini index 11dcecfc99..941426d732 100644 --- a/platformio.ini +++ b/platformio.ini @@ -59,6 +59,7 @@ default_src_filter = + - - + - - - - - + - - - - - - @@ -289,6 +290,7 @@ HAS_MENU_TRAMMING = src_filter=+ HAS_MENU_UBL = src_filter=+ ANYCUBIC_LCD_CHIRON = src_filter=+ + ANYCUBIC_LCD_I3MEGA = src_filter=+ + +NEXTION_TFT = src_filter=+ + HAS_DGUS_LCD = src_filter=+ + DGUS_LCD_UI_FYSETC = src_filter=+ DGUS_LCD_UI_HIPRECY = src_filter=+