Bump

config/examples/STM32/STM32F4/Configuration.h

@@ -275,7 +275,14 @@
     #define SWITCHING_TOOLHEAD_SERVO_ANGLES { 0, 180 }  // (degrees) Angles for Lock, Unlock
   #elif ENABLED(MAGNETIC_SWITCHING_TOOLHEAD)
     #define SWITCHING_TOOLHEAD_Y_RELEASE      5         // (mm) Security distance Y axis
-    #define SWITCHING_TOOLHEAD_X_SECURITY   -35         // (mm) Security distance X axis
+    #define SWITCHING_TOOLHEAD_X_SECURITY   { 90, 150 } // (mm) Security distance X axis (T0,T1)
+    //#define PRIME_BEFORE_REMOVE                       // Prime the nozzle before release from the dock
+    #if ENABLED(PRIME_BEFORE_REMOVE)
+      #define SWITCHING_TOOLHEAD_PRIME_MM           20  // (mm)   Extruder prime length
+      #define SWITCHING_TOOLHEAD_RETRACT_MM         10  // (mm)   Retract after priming length
+      #define SWITCHING_TOOLHEAD_PRIME_FEEDRATE    300  // (mm/m) Extruder prime feedrate
+      #define SWITCHING_TOOLHEAD_RETRACT_FEEDRATE 2400  // (mm/m) Extruder retract feedrate
+    #endif
   #elif ENABLED(ELECTROMAGNETIC_SWITCHING_TOOLHEAD)
     #define SWITCHING_TOOLHEAD_Z_HOP          2         // (mm) Z raise for switching
   #endif
@@ -513,7 +520,7 @@
 #define MAX_BED_POWER 255 // limits duty cycle to bed; 255=full current
 
 #if ENABLED(PIDTEMPBED)
-
+  //#define MIN_BED_POWER 0
   //#define PID_BED_DEBUG // Sends debug data to the serial port.
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
@@ -1522,8 +1529,11 @@
   // Middle point of circle
   #define NOZZLE_CLEAN_CIRCLE_MIDDLE NOZZLE_CLEAN_START_POINT
 
-  // Moves the nozzle to the initial position
+  // Move the nozzle to the initial position after cleaning
   #define NOZZLE_CLEAN_GOBACK
+
+  // Enable for a purge/clean station that's always at the gantry height (thus no Z move)
+  //#define NOZZLE_CLEAN_NO_Z
 #endif
 
 /**
@@ -1680,6 +1690,14 @@
 //
 //#define REVERSE_MENU_DIRECTION
 
+//
+// This option reverses the encoder direction for Select Screen.
+//
+//  If CLOCKWISE normally moves LEFT this makes it go RIGHT.
+//  If CLOCKWISE normally moves RIGHT this makes it go LEFT.
+//
+//#define REVERSE_SELECT_DIRECTION
+
 //
 // Individual Axis Homing
 //
@@ -2020,17 +2038,24 @@
 //=============================================================================
 
 //
-// MKS Robin 320x240 color display
+// FSMC display (MKS Robin, Alfawise U20, JGAurora A5S, A1, etc.)
 //
-//#define MKS_ROBIN_TFT
+//#define FSMC_GRAPHICAL_TFT
 
 //=============================================================================
 //============================  Other Controllers  ============================
 //=============================================================================
 
 //
-// CONTROLLER TYPE: Keypad / Add-on
+// ADS7843/XPT2046 ADC Touchscreen such as ILI9341 2.8
 //
+//#define TOUCH_BUTTONS
+#if ENABLED(TOUCH_BUTTONS)
+  #define XPT2046_X_CALIBRATION   12316
+  #define XPT2046_Y_CALIBRATION  -8981
+  #define XPT2046_X_OFFSET       -43
+  #define XPT2046_Y_OFFSET        257
+#endif
 
 //
 // RepRapWorld REPRAPWORLD_KEYPAD v1.1
@@ -2126,8 +2151,10 @@
 //#define NEOPIXEL_LED
 #if ENABLED(NEOPIXEL_LED)
   #define NEOPIXEL_TYPE   NEO_GRBW // NEO_GRBW / NEO_GRB - four/three channel driver type (defined in Adafruit_NeoPixel.h)
-  #define NEOPIXEL_PIN    4        // LED driving pin
-  #define NEOPIXEL_PIXELS 30       // Number of LEDs in the strip
+  #define NEOPIXEL_PIN     4       // LED driving pin
+  //#define NEOPIXEL2_TYPE NEOPIXEL_TYPE
+  //#define NEOPIXEL2_PIN    5
+  #define NEOPIXEL_PIXELS 30       // Number of LEDs in the strip, larger of 2 strips if 2 neopixel strips are used
   #define NEOPIXEL_IS_SEQUENTIAL   // Sequential display for temperature change - LED by LED. Disable to change all LEDs at once.
   #define NEOPIXEL_BRIGHTNESS 127  // Initial brightness (0-255)
   //#define NEOPIXEL_STARTUP_TEST  // Cycle through colors at startup