diff --git a/.gitignore b/.gitignore index a0b2708b14..6c68a71881 100755 --- a/.gitignore +++ b/.gitignore @@ -147,6 +147,7 @@ vc-fileutils.settings imgui.ini eeprom.dat spi_flash.bin +fs.img #cmake CMakeLists.txt diff --git a/Makefile b/Makefile index ebcdf25e2d..d0495dc7d8 100644 --- a/Makefile +++ b/Makefile @@ -27,7 +27,7 @@ tests-single-ci: tests-single-local: @if ! test -n "$(TEST_TARGET)" ; then echo "***ERROR*** Set TEST_TARGET= or use make tests-all-local" ; return 1; fi - export PATH=./buildroot/bin/:./buildroot/tests/:${PATH} \ + export PATH="./buildroot/bin/:./buildroot/tests/:${PATH}" \ && export VERBOSE_PLATFORMIO=$(VERBOSE_PLATFORMIO) \ && run_tests . $(TEST_TARGET) "$(ONLY_TEST)" .PHONY: tests-single-local @@ -38,7 +38,7 @@ tests-single-local-docker: .PHONY: tests-single-local-docker tests-all-local: - export PATH=./buildroot/bin/:./buildroot/tests/:${PATH} \ + export PATH="./buildroot/bin/:./buildroot/tests/:${PATH}" \ && export VERBOSE_PLATFORMIO=$(VERBOSE_PLATFORMIO) \ && for TEST_TARGET in $$(./get_test_targets.py) ; do echo "Running tests for $$TEST_TARGET" ; run_tests . $$TEST_TARGET ; done .PHONY: tests-all-local diff --git a/Marlin/Configuration.h b/Marlin/Configuration.h index 66e0d234fe..3804de5eb4 100644 --- a/Marlin/Configuration.h +++ b/Marlin/Configuration.h @@ -1251,7 +1251,7 @@ * 30 : 100kΩ Kis3d Silicone heating mat 200W/300W with 6mm precision cast plate (EN AW 5083) NTC100K - beta 3950 * 60 : 100kΩ Maker's Tool Works Kapton Bed Thermistor - beta 3950 * 61 : 100kΩ Formbot/Vivedino 350°C Thermistor - beta 3950 - * 66 : 4.7MΩ Dyze Design High Temperature Thermistor + * 66 : 4.7MΩ Dyze Design / Trianglelab T-D500 500°C High Temperature Thermistor * 67 : 500kΩ SliceEngineering 450°C Thermistor * 68 : PT100 amplifier board from Dyze Design * 70 : 100kΩ bq Hephestos 2 @@ -1273,6 +1273,7 @@ * 110 : Pt100 with 1kΩ pullup (atypical) * 147 : Pt100 with 4.7kΩ pullup * 1010 : Pt1000 with 1kΩ pullup (atypical) + * 1022 : Pt1000 with 2.2kΩ pullup * 1047 : Pt1000 with 4.7kΩ pullup (E3D) * 20 : Pt100 with circuit in the Ultimainboard V2.x with mainboard ADC reference voltage = INA826 amplifier-board supply voltage. * NOTE: (1) Must use an ADC input with no pullup. (2) Some INA826 amplifiers are unreliable at 3.3V so consider using sensor 147, 110, or 21. @@ -4532,6 +4533,7 @@ //#define ANYCUBIC_LCD_CHIRON #if EITHER(ANYCUBIC_LCD_I3MEGA, ANYCUBIC_LCD_CHIRON) //#define ANYCUBIC_LCD_DEBUG + //#define ANYCUBIC_LCD_GCODE_EXT // Add ".gcode" to menu entries for DGUS clone compatibility #endif // diff --git a/Marlin/Configuration_adv.h b/Marlin/Configuration_adv.h index 9688023ece..2cb7d4b967 100644 --- a/Marlin/Configuration_adv.h +++ b/Marlin/Configuration_adv.h @@ -1470,9 +1470,6 @@ // On the Info Screen, display XY with one decimal place when possible //#define LCD_DECIMAL_SMALL_XY - // Add an 'M73' G-code to set the current percentage - #define LCD_SET_PROGRESS_MANUALLY - // Show the E position (filament used) during printing //#define LCD_SHOW_E_TOTAL @@ -1493,37 +1490,43 @@ #define LED_USER_PRESET_STARTUP // Have the printer display the user preset color on startup #endif #if ENABLED(NEO2_COLOR_PRESETS) - #define NEO2_USER_PRESET_RED 255 // User defined RED value - #define NEO2_USER_PRESET_GREEN 128 // User defined GREEN value - #define NEO2_USER_PRESET_BLUE 0 // User defined BLUE value - #define NEO2_USER_PRESET_WHITE 255 // User defined WHITE value - #define NEO2_USER_PRESET_BRIGHTNESS 255 // User defined intensity - //#define NEO2_USER_PRESET_STARTUP // Have the printer display the user preset color on startup for the second strip + #define NEO2_USER_PRESET_RED 255 // User defined RED value + #define NEO2_USER_PRESET_GREEN 128 // User defined GREEN value + #define NEO2_USER_PRESET_BLUE 0 // User defined BLUE value + #define NEO2_USER_PRESET_WHITE 255 // User defined WHITE value + #define NEO2_USER_PRESET_BRIGHTNESS 255 // User defined intensity + //#define NEO2_USER_PRESET_STARTUP // Have the printer display the user preset color on startup for the second strip #endif #endif +#endif // HAS_DISPLAY || DWIN_LCD_PROUI + +// Add the G-code 'M73' to set / report the current job progress +#define SET_PROGRESS_MANUALLY +#if ENABLED(SET_PROGRESS_MANUALLY) + #define SET_PROGRESS_PERCENT // Add 'P' parameter to set percentage done, otherwise use Marlin's estimate + #define SET_REMAINING_TIME // Add 'R' parameter to set remaining time, otherwise use Marlin's estimate + //#define SET_INTERACTION_TIME // Add 'C' parameter to set time until next filament change or other user interaction + #if ENABLED(SET_INTERACTION_TIME) + #define SHOW_INTERACTION_TIME // Display time until next user interaction ('C' = filament change) + #endif + //#define M73_REPORT // Report progress to host with 'M73' #endif -// LCD Print Progress options -#if EITHER(SDSUPPORT, LCD_SET_PROGRESS_MANUALLY) - #if CAN_SHOW_REMAINING_TIME - #define SHOW_REMAINING_TIME // Display estimated time to completion - #if ENABLED(SHOW_REMAINING_TIME) - #define USE_M73_REMAINING_TIME // Use remaining time from M73 command instead of estimation - //#define ROTATE_PROGRESS_DISPLAY // Display (P)rogress, (E)lapsed, and (R)emaining time - #endif - #endif +// LCD Print Progress options, multiple can be rotated depending on screen layout +#if HAS_DISPLAY && EITHER(SDSUPPORT, SET_PROGRESS_MANUALLY) + #define SHOW_PROGRESS_PERCENT // Show print progress percentage (doesn't affect progress bar) + #define SHOW_ELAPSED_TIME // Display elapsed printing time (prefix 'E') + #define SHOW_REMAINING_TIME // Display estimated time to completion (prefix 'R') - #if EITHER(HAS_MARLINUI_U8GLIB, EXTENSIBLE_UI) - //#define PRINT_PROGRESS_SHOW_DECIMALS // Show progress with decimal digits - #endif + //#define PRINT_PROGRESS_SHOW_DECIMALS // Show/report progress with decimal digits, not all UIs support this #if EITHER(HAS_MARLINUI_HD44780, IS_TFTGLCD_PANEL) #define LCD_PROGRESS_BAR // Show a progress bar on HD44780 LCDs for SD printing #if ENABLED(LCD_PROGRESS_BAR) #define PROGRESS_BAR_BAR_TIME 2000 // (ms) Amount of time to show the bar #define PROGRESS_BAR_MSG_TIME 3000 // (ms) Amount of time to show the status message - #define PROGRESS_MSG_EXPIRE 0 // (ms) Amount of time to retain the status message (0=forever) + #define PROGRESS_MSG_EXPIRE 0 // (ms) Amount of time to retain the status message (0=forever) //#define PROGRESS_MSG_ONCE // Show the message for MSG_TIME then clear it //#define LCD_PROGRESS_BAR_TEST // Add a menu item to test the progress bar #endif @@ -1902,14 +1905,8 @@ #endif // HAS_GRAPHICAL_LCD #if HAS_MARLINUI_U8GLIB || IS_DWIN_MARLINUI - // Show SD percentage next to the progress bar - //#define SHOW_SD_PERCENT - - // Enable to save many cycles by drawing a hollow frame on Menu Screens - #define MENU_HOLLOW_FRAME - - // Swap the CW/CCW indicators in the graphics overlay - //#define OVERLAY_GFX_REVERSE + #define MENU_HOLLOW_FRAME // Enable to save many cycles by drawing a hollow frame on Menu Screens + //#define OVERLAY_GFX_REVERSE // Swap the CW/CCW indicators in the graphics overlay #endif // @@ -2176,12 +2173,16 @@ */ #define LIN_ADVANCE #if ENABLED(LIN_ADVANCE) - //#define EXTRA_LIN_ADVANCE_K // Add a second linear advance constant, configurable with M900. - #define LIN_ADVANCE_K 0.0 // Unit: mm compression per 1mm/s extruder speed - //#define LA_DEBUG // Print debug information to serial during operation. Disable for production use. - #define EXPERIMENTAL_SCURVE // Allow S-Curve Acceleration to be used with LA. - #define ALLOW_LOW_EJERK // Allow a DEFAULT_EJERK value of <10. Recommended for direct drive hotends. - //#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz. + #if ENABLED(DISTINCT_E_FACTORS) + #define ADVANCE_K { 0.0 } // (mm) Compression length per 1mm/s extruder speed, per extruder + #else + #define ADVANCE_K 0.0 // (mm) Compression length applying to all extruders + #endif + //#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L. + //#define LA_DEBUG // Print debug information to serial during operation. Disable for production use. + #define EXPERIMENTAL_SCURVE // Allow S-Curve Acceleration to be used with LA. + #define ALLOW_LOW_EJERK // Allow a DEFAULT_EJERK value of <10. Recommended for direct drive hotends. + //#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz. #endif // @section leveling @@ -4262,7 +4263,7 @@ /** * Mechanical Gantry Calibration - * Modern replacement for the Prusa TMC_Z_CALIBRATION. + * Modern replacement for the Průša TMC_Z_CALIBRATION. * Adds capability to work with any adjustable current drivers. * Implemented as G34 because M915 is deprecated. * @section calibrate diff --git a/Marlin/Version.h b/Marlin/Version.h index 4cffb6ee13..304ba7e6a3 100644 --- a/Marlin/Version.h +++ b/Marlin/Version.h @@ -131,7 +131,7 @@ * here we define this default string as the date where the latest release * version was tagged. */ -#define STRING_DISTRIBUTION_DATE "2022-09-14" +#define STRING_DISTRIBUTION_DATE "2022-10-16" /** * Defines a generic printer name to be output to the LCD after booting Marlin. diff --git a/Marlin/src/HAL/DUE/HAL.h b/Marlin/src/HAL/DUE/HAL.h index 4d3f4823a5..585b893841 100644 --- a/Marlin/src/HAL/DUE/HAL.h +++ b/Marlin/src/HAL/DUE/HAL.h @@ -210,7 +210,7 @@ public: static void adc_init() {} // Called by Temperature::init for each sensor at startup - static void adc_enable(const uint8_t ch) {} + static void adc_enable(const uint8_t /*ch*/) {} // Begin ADC sampling on the given channel. Called from Temperature::isr! static void adc_start(const uint8_t ch) { adc_result = analogRead(ch); } diff --git a/Marlin/src/HAL/DUE/HAL_SPI.cpp b/Marlin/src/HAL/DUE/HAL_SPI.cpp index 7e3fe01356..f5bcaacee5 100644 --- a/Marlin/src/HAL/DUE/HAL_SPI.cpp +++ b/Marlin/src/HAL/DUE/HAL_SPI.cpp @@ -247,12 +247,12 @@ b <<= 1; // little setup time WRITE(SD_SCK_PIN, HIGH); - DELAY_NS(spiDelayNS); + DELAY_NS_VAR(spiDelayNS); b |= (READ(SD_MISO_PIN) != 0); WRITE(SD_SCK_PIN, LOW); - DELAY_NS(spiDelayNS); + DELAY_NS_VAR(spiDelayNS); } while (--bits); return b; } diff --git a/Marlin/src/HAL/DUE/InterruptVectors.cpp b/Marlin/src/HAL/DUE/InterruptVectors.cpp index e4e0ce99f2..70795d1c30 100644 --- a/Marlin/src/HAL/DUE/InterruptVectors.cpp +++ b/Marlin/src/HAL/DUE/InterruptVectors.cpp @@ -41,7 +41,7 @@ practice, we need alignment to 256 bytes to make this work in all cases */ __attribute__ ((aligned(256))) -static DeviceVectors ram_tab = { nullptr }; +static DeviceVectors ram_tab[61] = { nullptr }; /** * This function checks if the exception/interrupt table is already in SRAM or not. diff --git a/Marlin/src/HAL/DUE/pinsDebug.h b/Marlin/src/HAL/DUE/pinsDebug.h index df1ba415e9..2aafe9be0c 100644 --- a/Marlin/src/HAL/DUE/pinsDebug.h +++ b/Marlin/src/HAL/DUE/pinsDebug.h @@ -70,7 +70,7 @@ #define PRINT_PIN_ANALOG(p) do{ sprintf_P(buffer, PSTR(" (A%2d) "), DIGITAL_PIN_TO_ANALOG_PIN(pin)); SERIAL_ECHO(buffer); }while(0) #define GET_ARRAY_PIN(p) pin_array[p].pin #define GET_ARRAY_IS_DIGITAL(p) pin_array[p].is_digital -#define VALID_PIN(pin) (pin >= 0 && pin < (int8_t)NUMBER_PINS_TOTAL ? 1 : 0) +#define VALID_PIN(pin) (pin >= 0 && pin < int8_t(NUMBER_PINS_TOTAL)) #define DIGITAL_PIN_TO_ANALOG_PIN(p) int(p - analogInputToDigitalPin(0)) #define IS_ANALOG(P) WITHIN(P, char(analogInputToDigitalPin(0)), char(analogInputToDigitalPin(NUM_ANALOG_INPUTS - 1))) #define pwm_status(pin) (((g_pinStatus[pin] & 0xF) == PIN_STATUS_PWM) && \ diff --git a/Marlin/src/HAL/DUE/upload_extra_script.py b/Marlin/src/HAL/DUE/upload_extra_script.py index 4f7a494512..ca12b3b54f 100644 --- a/Marlin/src/HAL/DUE/upload_extra_script.py +++ b/Marlin/src/HAL/DUE/upload_extra_script.py @@ -6,14 +6,14 @@ # import pioutil if pioutil.is_pio_build(): - import platform - current_OS = platform.system() + import platform + current_OS = platform.system() - if current_OS == 'Windows': + if current_OS == 'Windows': - Import("env") + Import("env") - # Use bossac.exe on Windows - env.Replace( - UPLOADCMD="bossac --info --unlock --write --verify --reset --erase -U false --boot $SOURCE" - ) + # Use bossac.exe on Windows + env.Replace( + UPLOADCMD="bossac --info --unlock --write --verify --reset --erase -U false --boot $SOURCE" + ) diff --git a/Marlin/src/HAL/DUE/usb/usb_task.c b/Marlin/src/HAL/DUE/usb/usb_task.c index 54a808d7f4..86ab27217a 100644 --- a/Marlin/src/HAL/DUE/usb/usb_task.c +++ b/Marlin/src/HAL/DUE/usb/usb_task.c @@ -62,7 +62,7 @@ void usb_task_idle(void) { // Attend SD card access from the USB MSD -- Prioritize access to improve speed int delay = 2; while (main_b_msc_enable && --delay > 0) { - if (udi_msc_process_trans()) delay = 10000; + if (udi_msc_process_trans()) delay = 20; // Reset the watchdog, just to be sure REG_WDT_CR = WDT_CR_WDRSTT | WDT_CR_KEY(0xA5); diff --git a/Marlin/src/HAL/LPC1768/upload_extra_script.py b/Marlin/src/HAL/LPC1768/upload_extra_script.py index 52c9a8e2ec..efd46fdd63 100755 --- a/Marlin/src/HAL/LPC1768/upload_extra_script.py +++ b/Marlin/src/HAL/LPC1768/upload_extra_script.py @@ -73,7 +73,7 @@ if pioutil.is_pio_build(): # import getpass user = getpass.getuser() - mpath = Path('media', user) + mpath = Path('/media', user) drives = [ x for x in mpath.iterdir() if x.is_dir() ] if target_drive in drives: # If target drive is found, use it. target_drive_found = True diff --git a/Marlin/src/HAL/SAMD51/pinsDebug.h b/Marlin/src/HAL/SAMD51/pinsDebug.h index f0a46fd7c5..639c4cd66e 100644 --- a/Marlin/src/HAL/SAMD51/pinsDebug.h +++ b/Marlin/src/HAL/SAMD51/pinsDebug.h @@ -29,7 +29,7 @@ #define PRINT_PIN_ANALOG(p) do{ sprintf_P(buffer, PSTR(" (A%2d) "), DIGITAL_PIN_TO_ANALOG_PIN(pin)); SERIAL_ECHO(buffer); }while(0) #define GET_ARRAY_PIN(p) pin_array[p].pin #define GET_ARRAY_IS_DIGITAL(p) pin_array[p].is_digital -#define VALID_PIN(pin) (pin >= 0 && pin < (int8_t)NUMBER_PINS_TOTAL) +#define VALID_PIN(pin) (pin >= 0 && pin < int8_t(NUMBER_PINS_TOTAL)) #define DIGITAL_PIN_TO_ANALOG_PIN(p) digitalPinToAnalogInput(p) #define IS_ANALOG(P) (DIGITAL_PIN_TO_ANALOG_PIN(P)!=-1) #define pwm_status(pin) digitalPinHasPWM(pin) diff --git a/Marlin/src/HAL/STM32/pinsDebug.h b/Marlin/src/HAL/STM32/pinsDebug.h index 55c64c8681..29a4e003f9 100644 --- a/Marlin/src/HAL/STM32/pinsDebug.h +++ b/Marlin/src/HAL/STM32/pinsDebug.h @@ -102,17 +102,18 @@ const XrefInfo pin_xref[] PROGMEM = { #define PIN_NUM_ALPHA_LEFT(P) (((P & 0x000F) < 10) ? ('0' + (P & 0x000F)) : '1') #define PIN_NUM_ALPHA_RIGHT(P) (((P & 0x000F) > 9) ? ('0' + (P & 0x000F) - 10) : 0 ) #define PORT_NUM(P) ((P >> 4) & 0x0007) -#define PORT_ALPHA(P) ('A' + (P >> 4)) +#define PORT_ALPHA(P) ('A' + (P >> 4)) /** * Translation of routines & variables used by pinsDebug.h */ -#if PA0 >= NUM_DIGITAL_PINS +#if NUM_ANALOG_FIRST >= NUM_DIGITAL_PINS #define HAS_HIGH_ANALOG_PINS 1 #endif -#define NUMBER_PINS_TOTAL NUM_DIGITAL_PINS + TERN0(HAS_HIGH_ANALOG_PINS, NUM_ANALOG_INPUTS) -#define VALID_PIN(ANUM) ((ANUM) >= 0 && (ANUM) < NUMBER_PINS_TOTAL) +#define NUM_ANALOG_LAST ((NUM_ANALOG_FIRST) + (NUM_ANALOG_INPUTS) - 1) +#define NUMBER_PINS_TOTAL ((NUM_DIGITAL_PINS) + TERN0(HAS_HIGH_ANALOG_PINS, NUM_ANALOG_INPUTS)) +#define VALID_PIN(P) (WITHIN(P, 0, (NUM_DIGITAL_PINS) - 1) || TERN0(HAS_HIGH_ANALOG_PINS, WITHIN(P, NUM_ANALOG_FIRST, NUM_ANALOG_LAST))) #define digitalRead_mod(Ard_num) extDigitalRead(Ard_num) // must use Arduino pin numbers when doing reads #define PRINT_PIN(Q) #define PRINT_PIN_ANALOG(p) do{ sprintf_P(buffer, PSTR(" (A%2d) "), DIGITAL_PIN_TO_ANALOG_PIN(pin)); SERIAL_ECHO(buffer); }while(0) @@ -168,7 +169,7 @@ bool GET_PINMODE(const pin_t Ard_num) { } int8_t digital_pin_to_analog_pin(const pin_t Ard_num) { - if (WITHIN(Ard_num, NUM_ANALOG_FIRST, NUM_ANALOG_FIRST + NUM_ANALOG_INPUTS - 1)) + if (WITHIN(Ard_num, NUM_ANALOG_FIRST, NUM_ANALOG_LAST)) return Ard_num - NUM_ANALOG_FIRST; const uint32_t ind = digitalPinToAnalogInput(Ard_num); @@ -206,8 +207,11 @@ void port_print(const pin_t Ard_num) { SERIAL_ECHO_SP(7); // Print number to be used with M42 - int calc_p = Ard_num % (NUM_DIGITAL_PINS + 1); - if (Ard_num > NUM_DIGITAL_PINS && calc_p > 7) calc_p += 8; + int calc_p = Ard_num; + if (Ard_num > NUM_DIGITAL_PINS) { + calc_p -= NUM_ANALOG_FIRST; + if (calc_p > 7) calc_p += 8; + } SERIAL_ECHOPGM(" M42 P", calc_p); SERIAL_CHAR(' '); if (calc_p < 100) { diff --git a/Marlin/src/HAL/TEENSY40_41/pinsDebug.h b/Marlin/src/HAL/TEENSY40_41/pinsDebug.h index 94b85ea568..fc90f671cf 100644 --- a/Marlin/src/HAL/TEENSY40_41/pinsDebug.h +++ b/Marlin/src/HAL/TEENSY40_41/pinsDebug.h @@ -36,7 +36,7 @@ #define PRINT_PIN_ANALOG(p) do{ sprintf_P(buffer, PSTR(" (A%2d) "), DIGITAL_PIN_TO_ANALOG_PIN(pin)); SERIAL_ECHO(buffer); }while(0) #define GET_ARRAY_PIN(p) pin_array[p].pin #define GET_ARRAY_IS_DIGITAL(p) pin_array[p].is_digital -#define VALID_PIN(pin) (pin >= 0 && pin < (int8_t)NUMBER_PINS_TOTAL ? 1 : 0) +#define VALID_PIN(pin) (pin >= 0 && pin < int8_t(NUMBER_PINS_TOTAL)) #define DIGITAL_PIN_TO_ANALOG_PIN(p) int(p - analogInputToDigitalPin(0)) #define IS_ANALOG(P) ((P) >= analogInputToDigitalPin(0) && (P) <= analogInputToDigitalPin(13)) || ((P) >= analogInputToDigitalPin(14) && (P) <= analogInputToDigitalPin(17)) #define pwm_status(pin) HAL_pwm_status(pin) diff --git a/Marlin/src/MarlinCore.cpp b/Marlin/src/MarlinCore.cpp index 0ea55b7ef4..ea57e3ccd7 100644 --- a/Marlin/src/MarlinCore.cpp +++ b/Marlin/src/MarlinCore.cpp @@ -347,7 +347,7 @@ void startOrResumeJob() { TERN_(GCODE_REPEAT_MARKERS, repeat.reset()); TERN_(CANCEL_OBJECTS, cancelable.reset()); TERN_(LCD_SHOW_E_TOTAL, e_move_accumulator = 0); - #if BOTH(LCD_SET_PROGRESS_MANUALLY, USE_M73_REMAINING_TIME) + #if ENABLED(SET_REMAINING_TIME) ui.reset_remaining_time(); #endif } diff --git a/Marlin/src/core/boards.h b/Marlin/src/core/boards.h index 42f8746aaf..74ff44d990 100644 --- a/Marlin/src/core/boards.h +++ b/Marlin/src/core/boards.h @@ -355,20 +355,21 @@ #define BOARD_CREALITY_V431_D 4051 // Creality v4.3.1d (STM32F103RC / STM32F103RE) #define BOARD_CREALITY_V452 4052 // Creality v4.5.2 (STM32F103RC / STM32F103RE) #define BOARD_CREALITY_V453 4053 // Creality v4.5.3 (STM32F103RC / STM32F103RE) -#define BOARD_CREALITY_V24S1 4054 // Creality v2.4.S1 (STM32F103RC / STM32F103RE) v101 as found in the Ender-7 -#define BOARD_CREALITY_V24S1_301 4055 // Creality v2.4.S1_301 (STM32F103RC / STM32F103RE) v301 as found in the Ender-3 S1 -#define BOARD_CREALITY_V25S1 4056 // Creality v2.5.S1 (STM32F103RE) as found in the CR-10 Smart Pro -#define BOARD_TRIGORILLA_PRO 4057 // Trigorilla Pro (STM32F103ZE) -#define BOARD_FLY_MINI 4058 // FLYmaker FLY MINI (STM32F103RC) -#define BOARD_FLSUN_HISPEED 4059 // FLSUN HiSpeedV1 (STM32F103VE) -#define BOARD_BEAST 4060 // STM32F103RE Libmaple-based controller -#define BOARD_MINGDA_MPX_ARM_MINI 4061 // STM32F103ZE Mingda MD-16 -#define BOARD_GTM32_PRO_VD 4062 // STM32F103VE controller -#define BOARD_ZONESTAR_ZM3E2 4063 // Zonestar ZM3E2 (STM32F103RC) -#define BOARD_ZONESTAR_ZM3E4 4064 // Zonestar ZM3E4 V1 (STM32F103VC) -#define BOARD_ZONESTAR_ZM3E4V2 4065 // Zonestar ZM3E4 V2 (STM32F103VC) -#define BOARD_ERYONE_ERY32_MINI 4066 // Eryone Ery32 mini (STM32F103VE) -#define BOARD_PANDA_PI_V29 4067 // Panda Pi V2.9 - Standalone (STM32F103RC) +#define BOARD_CREALITY_V521 4054 // Creality v5.2.1 (STM32F103VE) as found in the SV04 +#define BOARD_CREALITY_V24S1 4055 // Creality v2.4.S1 (STM32F103RC / STM32F103RE) v101 as found in the Ender-7 +#define BOARD_CREALITY_V24S1_301 4056 // Creality v2.4.S1_301 (STM32F103RC / STM32F103RE) v301 as found in the Ender-3 S1 +#define BOARD_CREALITY_V25S1 4057 // Creality v2.5.S1 (STM32F103RE) as found in the CR-10 Smart Pro +#define BOARD_TRIGORILLA_PRO 4058 // Trigorilla Pro (STM32F103ZE) +#define BOARD_FLY_MINI 4059 // FLYmaker FLY MINI (STM32F103RC) +#define BOARD_FLSUN_HISPEED 4060 // FLSUN HiSpeedV1 (STM32F103VE) +#define BOARD_BEAST 4061 // STM32F103RE Libmaple-based controller +#define BOARD_MINGDA_MPX_ARM_MINI 4062 // STM32F103ZE Mingda MD-16 +#define BOARD_GTM32_PRO_VD 4063 // STM32F103VE controller +#define BOARD_ZONESTAR_ZM3E2 4064 // Zonestar ZM3E2 (STM32F103RC) +#define BOARD_ZONESTAR_ZM3E4 4065 // Zonestar ZM3E4 V1 (STM32F103VC) +#define BOARD_ZONESTAR_ZM3E4V2 4066 // Zonestar ZM3E4 V2 (STM32F103VC) +#define BOARD_ERYONE_ERY32_MINI 4067 // Eryone Ery32 mini (STM32F103VE) +#define BOARD_PANDA_PI_V29 4068 // Panda Pi V2.9 - Standalone (STM32F103RC) // // ARM Cortex-M4F @@ -424,6 +425,7 @@ #define BOARD_CREALITY_V24S1_301F4 4240 // Creality v2.4.S1_301F4 (STM32F401RC) as found in the Ender-3 S1 F4 #define BOARD_OPULO_LUMEN_REV4 4241 // Opulo Lumen PnP Controller REV4 (STM32F407VE / STM32F407VG) #define BOARD_FYSETC_SPIDER_KING407 4242 // FYSETC Spider King407 (STM32F407ZG) +#define BOARD_MKS_SKIPR_V1 4243 // MKS SKIPR v1.0 all-in-one board (STM32F407VE) // // ARM Cortex M7 diff --git a/Marlin/src/core/macros.h b/Marlin/src/core/macros.h index 8dfcb875ac..3029009c06 100644 --- a/Marlin/src/core/macros.h +++ b/Marlin/src/core/macros.h @@ -338,6 +338,12 @@ #define GANG_N_1(N,K) _GANG_N(N,K,K,K,K,K,K,K,K,K,K,K,K,K,K,K,K) // Macros for initializing arrays +#define LIST_26(A,B,C,D,E,F,G,H,I,J,K,L,M,N,O,P,Q,R,S,T,U,V,W,X,Y,Z,...) A,B,C,D,E,F,G,H,I,J,K,L,M,N,O,P,Q,R,S,T,U,V,W,X,Y,Z +#define LIST_25(A,B,C,D,E,F,G,H,I,J,K,L,M,N,O,P,Q,R,S,T,U,V,W,X,Y,...) A,B,C,D,E,F,G,H,I,J,K,L,M,N,O,P,Q,R,S,T,U,V,W,X,Y +#define LIST_24(A,B,C,D,E,F,G,H,I,J,K,L,M,N,O,P,Q,R,S,T,U,V,W,X,...) A,B,C,D,E,F,G,H,I,J,K,L,M,N,O,P,Q,R,S,T,U,V,W,X +#define LIST_23(A,B,C,D,E,F,G,H,I,J,K,L,M,N,O,P,Q,R,S,T,U,V,W,...) A,B,C,D,E,F,G,H,I,J,K,L,M,N,O,P,Q,R,S,T,U,V,W +#define LIST_22(A,B,C,D,E,F,G,H,I,J,K,L,M,N,O,P,Q,R,S,T,U,V,...) A,B,C,D,E,F,G,H,I,J,K,L,M,N,O,P,Q,R,S,T,U,V +#define LIST_21(A,B,C,D,E,F,G,H,I,J,K,L,M,N,O,P,Q,R,S,T,U,...) A,B,C,D,E,F,G,H,I,J,K,L,M,N,O,P,Q,R,S,T,U #define LIST_20(A,B,C,D,E,F,G,H,I,J,K,L,M,N,O,P,Q,R,S,T,...) A,B,C,D,E,F,G,H,I,J,K,L,M,N,O,P,Q,R,S,T #define LIST_19(A,B,C,D,E,F,G,H,I,J,K,L,M,N,O,P,Q,R,S,...) A,B,C,D,E,F,G,H,I,J,K,L,M,N,O,P,Q,R,S #define LIST_18(A,B,C,D,E,F,G,H,I,J,K,L,M,N,O,P,Q,R,...) A,B,C,D,E,F,G,H,I,J,K,L,M,N,O,P,Q,R @@ -732,6 +738,7 @@ #define MAPLIST(OP,V...) EVAL(_MAPLIST(OP,V)) // Temperature Sensor Config -#define _HAS_E_TEMP(N) || (TEMP_SENSOR_##N != 0) +#define TEMP_SENSOR(N) TEMP_SENSOR_##N +#define _HAS_E_TEMP(N) || TEMP_SENSOR(N) #define HAS_E_TEMP_SENSOR (0 REPEAT(EXTRUDERS, _HAS_E_TEMP)) -#define TEMP_SENSOR_IS_MAX_TC(T) (TEMP_SENSOR_##T == -5 || TEMP_SENSOR_##T == -3 || TEMP_SENSOR_##T == -2) +#define TEMP_SENSOR_IS_MAX_TC(T) (TEMP_SENSOR(T) == -5 || TEMP_SENSOR(T) == -3 || TEMP_SENSOR(T) == -2) diff --git a/Marlin/src/core/types.h b/Marlin/src/core/types.h index f0ddc871a5..4497ff49af 100644 --- a/Marlin/src/core/types.h +++ b/Marlin/src/core/types.h @@ -99,8 +99,8 @@ struct Flags { void set(const int n) { b |= (bits_t)_BV(n); } void clear(const int n) { b &= ~(bits_t)_BV(n); } bool test(const int n) const { return TEST(b, n); } - const bool operator[](const int n) { return test(n); } - const bool operator[](const int n) const { return test(n); } + bool operator[](const int n) { return test(n); } + bool operator[](const int n) const { return test(n); } int size() const { return sizeof(b); } }; @@ -226,8 +226,8 @@ typedef const_float_t const_celsius_float_t; // Helpers #define _RECIP(N) ((N) ? 1.0f / static_cast(N) : 0.0f) #define _ABS(N) ((N) < 0 ? -(N) : (N)) -#define _LS(N) (N = (T)(uint32_t(N) << v)) -#define _RS(N) (N = (T)(uint32_t(N) >> v)) +#define _LS(N) (N = (T)(uint32_t(N) << p)) +#define _RS(N) (N = (T)(uint32_t(N) >> p)) #define FI FORCE_INLINE // Forward declarations @@ -347,6 +347,10 @@ struct XYval { FI operator T* () { return pos; } // If any element is true then it's true FI operator bool() { return x || y; } + // Smallest element + FI T small() const { return _MIN(x, y); } + // Largest element + FI T large() const { return _MAX(x, y); } // Explicit copy and copies with conversion FI XYval copy() const { return *this; } @@ -405,18 +409,18 @@ struct XYval { FI XYval operator* (const XYZEval &rs) { XYval ls = *this; ls.x *= rs.x; ls.y *= rs.y; return ls; } FI XYval operator/ (const XYZEval &rs) const { XYval ls = *this; ls.x /= rs.x; ls.y /= rs.y; return ls; } FI XYval operator/ (const XYZEval &rs) { XYval ls = *this; ls.x /= rs.x; ls.y /= rs.y; return ls; } - FI XYval operator* (const float &v) const { XYval ls = *this; ls.x *= v; ls.y *= v; return ls; } - FI XYval operator* (const float &v) { XYval ls = *this; ls.x *= v; ls.y *= v; return ls; } - FI XYval operator* (const int &v) const { XYval ls = *this; ls.x *= v; ls.y *= v; return ls; } - FI XYval operator* (const int &v) { XYval ls = *this; ls.x *= v; ls.y *= v; return ls; } - FI XYval operator/ (const float &v) const { XYval ls = *this; ls.x /= v; ls.y /= v; return ls; } - FI XYval operator/ (const float &v) { XYval ls = *this; ls.x /= v; ls.y /= v; return ls; } - FI XYval operator/ (const int &v) const { XYval ls = *this; ls.x /= v; ls.y /= v; return ls; } - FI XYval operator/ (const int &v) { XYval ls = *this; ls.x /= v; ls.y /= v; return ls; } - FI XYval operator>>(const int &v) const { XYval ls = *this; _RS(ls.x); _RS(ls.y); return ls; } - FI XYval operator>>(const int &v) { XYval ls = *this; _RS(ls.x); _RS(ls.y); return ls; } - FI XYval operator<<(const int &v) const { XYval ls = *this; _LS(ls.x); _LS(ls.y); return ls; } - FI XYval operator<<(const int &v) { XYval ls = *this; _LS(ls.x); _LS(ls.y); return ls; } + FI XYval operator* (const float &p) const { XYval ls = *this; ls.x *= p; ls.y *= p; return ls; } + FI XYval operator* (const float &p) { XYval ls = *this; ls.x *= p; ls.y *= p; return ls; } + FI XYval operator* (const int &p) const { XYval ls = *this; ls.x *= p; ls.y *= p; return ls; } + FI XYval operator* (const int &p) { XYval ls = *this; ls.x *= p; ls.y *= p; return ls; } + FI XYval operator/ (const float &p) const { XYval ls = *this; ls.x /= p; ls.y /= p; return ls; } + FI XYval operator/ (const float &p) { XYval ls = *this; ls.x /= p; ls.y /= p; return ls; } + FI XYval operator/ (const int &p) const { XYval ls = *this; ls.x /= p; ls.y /= p; return ls; } + FI XYval operator/ (const int &p) { XYval ls = *this; ls.x /= p; ls.y /= p; return ls; } + FI XYval operator>>(const int &p) const { XYval ls = *this; _RS(ls.x); _RS(ls.y); return ls; } + FI XYval operator>>(const int &p) { XYval ls = *this; _RS(ls.x); _RS(ls.y); return ls; } + FI XYval operator<<(const int &p) const { XYval ls = *this; _LS(ls.x); _LS(ls.y); return ls; } + FI XYval operator<<(const int &p) { XYval ls = *this; _LS(ls.x); _LS(ls.y); return ls; } FI const XYval operator-() const { XYval o = *this; o.x = -x; o.y = -y; return o; } FI XYval operator-() { XYval o = *this; o.x = -x; o.y = -y; return o; } @@ -430,21 +434,15 @@ struct XYval { FI XYval& operator+=(const XYZEval &rs) { x += rs.x; y += rs.y; return *this; } FI XYval& operator-=(const XYZEval &rs) { x -= rs.x; y -= rs.y; return *this; } FI XYval& operator*=(const XYZEval &rs) { x *= rs.x; y *= rs.y; return *this; } - FI XYval& operator*=(const float &v) { x *= v; y *= v; return *this; } - FI XYval& operator*=(const int &v) { x *= v; y *= v; return *this; } - FI XYval& operator>>=(const int &v) { _RS(x); _RS(y); return *this; } - FI XYval& operator<<=(const int &v) { _LS(x); _LS(y); return *this; } + FI XYval& operator*=(const float &p) { x *= p; y *= p; return *this; } + FI XYval& operator*=(const int &p) { x *= p; y *= p; return *this; } + FI XYval& operator>>=(const int &p) { _RS(x); _RS(y); return *this; } + FI XYval& operator<<=(const int &p) { _LS(x); _LS(y); return *this; } // Exact comparisons. For floats a "NEAR" operation may be better. - FI bool operator==(const XYval &rs) { return x == rs.x && y == rs.y; } - FI bool operator==(const XYZval &rs) { return x == rs.x && y == rs.y; } - FI bool operator==(const XYZEval &rs) { return x == rs.x && y == rs.y; } FI bool operator==(const XYval &rs) const { return x == rs.x && y == rs.y; } FI bool operator==(const XYZval &rs) const { return x == rs.x && y == rs.y; } FI bool operator==(const XYZEval &rs) const { return x == rs.x && y == rs.y; } - FI bool operator!=(const XYval &rs) { return !operator==(rs); } - FI bool operator!=(const XYZval &rs) { return !operator==(rs); } - FI bool operator!=(const XYZEval &rs) { return !operator==(rs); } FI bool operator!=(const XYval &rs) const { return !operator==(rs); } FI bool operator!=(const XYZval &rs) const { return !operator==(rs); } FI bool operator!=(const XYZEval &rs) const { return !operator==(rs); } @@ -494,10 +492,10 @@ struct XYZval { FI void set(const T px, const T py, const T pz, const T pi, const T pj, const T pk) { x = px; y = py; z = pz; i = pi; j = pj; k = pk; } #endif #if HAS_V_AXIS - FI void set(const T px, const T py, const T pz, const T pi, const T pj, const T pk, const T pm) { x = px; y = py; z = pz; i = pi; j = pj; k = pk; u = pu; } + FI void set(const T px, const T py, const T pz, const T pi, const T pj, const T pk, const T pu) { x = px; y = py; z = pz; i = pi; j = pj; k = pk; u = pu; } #endif #if HAS_W_AXIS - FI void set(const T px, const T py, const T pz, const T pi, const T pj, const T pk, const T pm, const T po) { x = px; y = py; z = pz; i = pi; j = pj; k = pk; u = pu; v = pv; } + FI void set(const T px, const T py, const T pz, const T pi, const T pj, const T pk, const T pu, const T pv) { x = px; y = py; z = pz; i = pi; j = pj; k = pk; u = pu; v = pv; } #endif // Length reduced to one dimension @@ -506,6 +504,10 @@ struct XYZval { FI operator T* () { return pos; } // If any element is true then it's true FI operator bool() { return NUM_AXIS_GANG(x, || y, || z, || i, || j, || k, || u, || v, || w); } + // Smallest element + FI T small() const { return _MIN(NUM_AXIS_LIST(x, y, z, i, j, k, u, v, w)); } + // Largest element + FI T large() const { return _MAX(NUM_AXIS_LIST(x, y, z, i, j, k, u, v, w)); } // Explicit copy and copies with conversion FI XYZval copy() const { XYZval o = *this; return o; } @@ -565,18 +567,18 @@ struct XYZval { FI XYZval operator* (const XYZEval &rs) { XYZval ls = *this; NUM_AXIS_CODE(ls.x *= rs.x, ls.y *= rs.y, ls.z *= rs.z, ls.i *= rs.i, ls.j *= rs.j, ls.k *= rs.k, ls.u *= rs.u, ls.v *= rs.v, ls.w *= rs.w); return ls; } FI XYZval operator/ (const XYZEval &rs) const { XYZval ls = *this; NUM_AXIS_CODE(ls.x /= rs.x, ls.y /= rs.y, ls.z /= rs.z, ls.i /= rs.i, ls.j /= rs.j, ls.k /= rs.k, ls.u /= rs.u, ls.v /= rs.v, ls.w /= rs.w); return ls; } FI XYZval operator/ (const XYZEval &rs) { XYZval ls = *this; NUM_AXIS_CODE(ls.x /= rs.x, ls.y /= rs.y, ls.z /= rs.z, ls.i /= rs.i, ls.j /= rs.j, ls.k /= rs.k, ls.u /= rs.u, ls.v /= rs.v, ls.w /= rs.w); return ls; } - FI XYZval operator* (const float &v) const { XYZval ls = *this; NUM_AXIS_CODE(ls.x *= v, ls.y *= v, ls.z *= v, ls.i *= v, ls.j *= v, ls.k *= v, ls.u *= v, ls.v *= v, ls.w *= v ); return ls; } - FI XYZval operator* (const float &v) { XYZval ls = *this; NUM_AXIS_CODE(ls.x *= v, ls.y *= v, ls.z *= v, ls.i *= v, ls.j *= v, ls.k *= v, ls.u *= v, ls.v *= v, ls.w *= v ); return ls; } - FI XYZval operator* (const int &v) const { XYZval ls = *this; NUM_AXIS_CODE(ls.x *= v, ls.y *= v, ls.z *= v, ls.i *= v, ls.j *= v, ls.k *= v, ls.u *= v, ls.v *= v, ls.w *= v ); return ls; } - FI XYZval operator* (const int &v) { XYZval ls = *this; NUM_AXIS_CODE(ls.x *= v, ls.y *= v, ls.z *= v, ls.i *= v, ls.j *= v, ls.k *= v, ls.u *= v, ls.v *= v, ls.w *= v ); return ls; } - FI XYZval operator/ (const float &v) const { XYZval ls = *this; NUM_AXIS_CODE(ls.x /= v, ls.y /= v, ls.z /= v, ls.i /= v, ls.j /= v, ls.k /= v, ls.u /= v, ls.v /= v, ls.w /= v ); return ls; } - FI XYZval operator/ (const float &v) { XYZval ls = *this; NUM_AXIS_CODE(ls.x /= v, ls.y /= v, ls.z /= v, ls.i /= v, ls.j /= v, ls.k /= v, ls.u /= v, ls.v /= v, ls.w /= v ); return ls; } - FI XYZval operator/ (const int &v) const { XYZval ls = *this; NUM_AXIS_CODE(ls.x /= v, ls.y /= v, ls.z /= v, ls.i /= v, ls.j /= v, ls.k /= v, ls.u /= v, ls.v /= v, ls.w /= v ); return ls; } - FI XYZval operator/ (const int &v) { XYZval ls = *this; NUM_AXIS_CODE(ls.x /= v, ls.y /= v, ls.z /= v, ls.i /= v, ls.j /= v, ls.k /= v, ls.u /= v, ls.v /= v, ls.w /= v ); return ls; } - FI XYZval operator>>(const int &v) const { XYZval ls = *this; NUM_AXIS_CODE(_RS(ls.x), _RS(ls.y), _RS(ls.z), _RS(ls.i), _RS(ls.j), _RS(ls.k), _RS(ls.u), _RS(ls.v), _RS(ls.w) ); return ls; } - FI XYZval operator>>(const int &v) { XYZval ls = *this; NUM_AXIS_CODE(_RS(ls.x), _RS(ls.y), _RS(ls.z), _RS(ls.i), _RS(ls.j), _RS(ls.k), _RS(ls.u), _RS(ls.v), _RS(ls.w) ); return ls; } - FI XYZval operator<<(const int &v) const { XYZval ls = *this; NUM_AXIS_CODE(_LS(ls.x), _LS(ls.y), _LS(ls.z), _LS(ls.i), _LS(ls.j), _LS(ls.k), _LS(ls.u), _LS(ls.v), _LS(ls.w) ); return ls; } - FI XYZval operator<<(const int &v) { XYZval ls = *this; NUM_AXIS_CODE(_LS(ls.x), _LS(ls.y), _LS(ls.z), _LS(ls.i), _LS(ls.j), _LS(ls.k), _LS(ls.u), _LS(ls.v), _LS(ls.w) ); return ls; } + FI XYZval operator* (const float &p) const { XYZval ls = *this; NUM_AXIS_CODE(ls.x *= p, ls.y *= p, ls.z *= p, ls.i *= p, ls.j *= p, ls.k *= p, ls.u *= p, ls.v *= p, ls.w *= p ); return ls; } + FI XYZval operator* (const float &p) { XYZval ls = *this; NUM_AXIS_CODE(ls.x *= p, ls.y *= p, ls.z *= p, ls.i *= p, ls.j *= p, ls.k *= p, ls.u *= p, ls.v *= p, ls.w *= p ); return ls; } + FI XYZval operator* (const int &p) const { XYZval ls = *this; NUM_AXIS_CODE(ls.x *= p, ls.y *= p, ls.z *= p, ls.i *= p, ls.j *= p, ls.k *= p, ls.u *= p, ls.v *= p, ls.w *= p ); return ls; } + FI XYZval operator* (const int &p) { XYZval ls = *this; NUM_AXIS_CODE(ls.x *= p, ls.y *= p, ls.z *= p, ls.i *= p, ls.j *= p, ls.k *= p, ls.u *= p, ls.v *= p, ls.w *= p ); return ls; } + FI XYZval operator/ (const float &p) const { XYZval ls = *this; NUM_AXIS_CODE(ls.x /= p, ls.y /= p, ls.z /= p, ls.i /= p, ls.j /= p, ls.k /= p, ls.u /= p, ls.v /= p, ls.w /= p ); return ls; } + FI XYZval operator/ (const float &p) { XYZval ls = *this; NUM_AXIS_CODE(ls.x /= p, ls.y /= p, ls.z /= p, ls.i /= p, ls.j /= p, ls.k /= p, ls.u /= p, ls.v /= p, ls.w /= p ); return ls; } + FI XYZval operator/ (const int &p) const { XYZval ls = *this; NUM_AXIS_CODE(ls.x /= p, ls.y /= p, ls.z /= p, ls.i /= p, ls.j /= p, ls.k /= p, ls.u /= p, ls.v /= p, ls.w /= p ); return ls; } + FI XYZval operator/ (const int &p) { XYZval ls = *this; NUM_AXIS_CODE(ls.x /= p, ls.y /= p, ls.z /= p, ls.i /= p, ls.j /= p, ls.k /= p, ls.u /= p, ls.v /= p, ls.w /= p ); return ls; } + FI XYZval operator>>(const int &p) const { XYZval ls = *this; NUM_AXIS_CODE(_RS(ls.x), _RS(ls.y), _RS(ls.z), _RS(ls.i), _RS(ls.j), _RS(ls.k), _RS(ls.u), _RS(ls.v), _RS(ls.w) ); return ls; } + FI XYZval operator>>(const int &p) { XYZval ls = *this; NUM_AXIS_CODE(_RS(ls.x), _RS(ls.y), _RS(ls.z), _RS(ls.i), _RS(ls.j), _RS(ls.k), _RS(ls.u), _RS(ls.v), _RS(ls.w) ); return ls; } + FI XYZval operator<<(const int &p) const { XYZval ls = *this; NUM_AXIS_CODE(_LS(ls.x), _LS(ls.y), _LS(ls.z), _LS(ls.i), _LS(ls.j), _LS(ls.k), _LS(ls.u), _LS(ls.v), _LS(ls.w) ); return ls; } + FI XYZval operator<<(const int &p) { XYZval ls = *this; NUM_AXIS_CODE(_LS(ls.x), _LS(ls.y), _LS(ls.z), _LS(ls.i), _LS(ls.j), _LS(ls.k), _LS(ls.u), _LS(ls.v), _LS(ls.w) ); return ls; } FI const XYZval operator-() const { XYZval o = *this; NUM_AXIS_CODE(o.x = -x, o.y = -y, o.z = -z, o.i = -i, o.j = -j, o.k = -k, o.u = -u, o.v = -v, o.w = -w); return o; } FI XYZval operator-() { XYZval o = *this; NUM_AXIS_CODE(o.x = -x, o.y = -y, o.z = -z, o.i = -i, o.j = -j, o.k = -k, o.u = -u, o.v = -v, o.w = -w); return o; } @@ -593,15 +595,13 @@ struct XYZval { FI XYZval& operator-=(const XYZEval &rs) { NUM_AXIS_CODE(x -= rs.x, y -= rs.y, z -= rs.z, i -= rs.i, j -= rs.j, k -= rs.k, u -= rs.u, v -= rs.v, w -= rs.w); return *this; } FI XYZval& operator*=(const XYZEval &rs) { NUM_AXIS_CODE(x *= rs.x, y *= rs.y, z *= rs.z, i *= rs.i, j *= rs.j, k *= rs.k, u *= rs.u, v *= rs.v, w *= rs.w); return *this; } FI XYZval& operator/=(const XYZEval &rs) { NUM_AXIS_CODE(x /= rs.x, y /= rs.y, z /= rs.z, i /= rs.i, j /= rs.j, k /= rs.k, u /= rs.u, v /= rs.v, w /= rs.w); return *this; } - FI XYZval& operator*=(const float &v) { NUM_AXIS_CODE(x *= v, y *= v, z *= v, i *= v, j *= v, k *= v, u *= v, v *= v, w *= v); return *this; } - FI XYZval& operator*=(const int &v) { NUM_AXIS_CODE(x *= v, y *= v, z *= v, i *= v, j *= v, k *= v, u *= v, v *= v, w *= v); return *this; } - FI XYZval& operator>>=(const int &v) { NUM_AXIS_CODE(_RS(x), _RS(y), _RS(z), _RS(i), _RS(j), _RS(k), _RS(u), _RS(v), _RS(w)); return *this; } - FI XYZval& operator<<=(const int &v) { NUM_AXIS_CODE(_LS(x), _LS(y), _LS(z), _LS(i), _LS(j), _LS(k), _LS(u), _LS(v), _LS(w)); return *this; } + FI XYZval& operator*=(const float &p) { NUM_AXIS_CODE(x *= p, y *= p, z *= p, i *= p, j *= p, k *= p, u *= p, v *= p, w *= p); return *this; } + FI XYZval& operator*=(const int &p) { NUM_AXIS_CODE(x *= p, y *= p, z *= p, i *= p, j *= p, k *= p, u *= p, v *= p, w *= p); return *this; } + FI XYZval& operator>>=(const int &p) { NUM_AXIS_CODE(_RS(x), _RS(y), _RS(z), _RS(i), _RS(j), _RS(k), _RS(u), _RS(v), _RS(w)); return *this; } + FI XYZval& operator<<=(const int &p) { NUM_AXIS_CODE(_LS(x), _LS(y), _LS(z), _LS(i), _LS(j), _LS(k), _LS(u), _LS(v), _LS(w)); return *this; } // Exact comparisons. For floats a "NEAR" operation may be better. - FI bool operator==(const XYZEval &rs) { return true NUM_AXIS_GANG(&& x == rs.x, && y == rs.y, && z == rs.z, && i == rs.i, && j == rs.j, && k == rs.k, && u == rs.u, && v == rs.v, && w == rs.w); } FI bool operator==(const XYZEval &rs) const { return true NUM_AXIS_GANG(&& x == rs.x, && y == rs.y, && z == rs.z, && i == rs.i, && j == rs.j, && k == rs.k, && u == rs.u, && v == rs.v, && w == rs.w); } - FI bool operator!=(const XYZEval &rs) { return !operator==(rs); } FI bool operator!=(const XYZEval &rs) const { return !operator==(rs); } }; @@ -634,10 +634,10 @@ struct XYZEval { FI void set(const T px, const T py, const T pz, const T pi, const T pj, const T pk) { x = px; y = py; z = pz; i = pi; j = pj; k = pk; } #endif #if HAS_V_AXIS - FI void set(const T px, const T py, const T pz, const T pi, const T pj, const T pk, const T pm) { x = px; y = py; z = pz; i = pi; j = pj; k = pk; u = pu; } + FI void set(const T px, const T py, const T pz, const T pi, const T pj, const T pk, const T pu) { x = px; y = py; z = pz; i = pi; j = pj; k = pk; u = pu; } #endif #if HAS_W_AXIS - FI void set(const T px, const T py, const T pz, const T pi, const T pj, const T pk, const T pm, const T po) { x = px; y = py; z = pz; i = pi; j = pj; k = pk; u = pm; v = pv; } + FI void set(const T px, const T py, const T pz, const T pi, const T pj, const T pk, const T pu, const T pv) { x = px; y = py; z = pz; i = pi; j = pj; k = pk; u = pu; v = pv; } #endif // Setters taking struct types and arrays @@ -654,11 +654,15 @@ struct XYZEval { #endif // Length reduced to one dimension - FI T magnitude() const { return (T)sqrtf(LOGICAL_AXIS_GANG(+ e*e, + x*x, + y*y, + z*z, + i*i, + j*j, + k*k, + u*u, + v*v, + w*w)); } + FI T magnitude() const { return (T)sqrtf(LOGICAL_AXIS_GANG(+ e*e, + x*x, + y*y, + z*z, + i*i, + j*j, + k*k, + u*u, + v*v, + w*w)); } // Pointer to the data as a simple array - FI operator T* () { return pos; } + FI operator T* () { return pos; } // If any element is true then it's true - FI operator bool() { return 0 LOGICAL_AXIS_GANG(|| e, || x, || y, || z, || i, || j, || k, || u, || v, || w); } + FI operator bool() { return 0 LOGICAL_AXIS_GANG(|| e, || x, || y, || z, || i, || j, || k, || u, || v, || w); } + // Smallest element + FI T small() const { return _MIN(LOGICAL_AXIS_LIST(e, x, y, z, i, j, k, u, v, w)); } + // Largest element + FI T large() const { return _MAX(LOGICAL_AXIS_LIST(e, x, y, z, i, j, k, u, v, w)); } // Explicit copy and copies with conversion FI XYZEval copy() const { XYZEval v = *this; return v; } @@ -684,80 +688,76 @@ struct XYZEval { FI operator const XYZval&() const { return *(const XYZval*)this; } // Accessor via an AxisEnum (or any integer) [index] - FI T& operator[](const int n) { return pos[n]; } - FI const T& operator[](const int n) const { return pos[n]; } + FI T& operator[](const int n) { return pos[n]; } + FI const T& operator[](const int n) const { return pos[n]; } // Assignment operator overrides do the expected thing - FI XYZEval& operator= (const T v) { set(LOGICAL_AXIS_LIST_1(v)); return *this; } - FI XYZEval& operator= (const XYval &rs) { set(rs.x, rs.y); return *this; } - FI XYZEval& operator= (const XYZval &rs) { set(NUM_AXIS_ELEM(rs)); return *this; } + FI XYZEval& operator= (const T v) { set(LOGICAL_AXIS_LIST_1(v)); return *this; } + FI XYZEval& operator= (const XYval &rs) { set(rs.x, rs.y); return *this; } + FI XYZEval& operator= (const XYZval &rs) { set(NUM_AXIS_ELEM(rs)); return *this; } // Override other operators to get intuitive behaviors - FI XYZEval operator+ (const XYval &rs) const { XYZEval ls = *this; ls.x += rs.x; ls.y += rs.y; return ls; } - FI XYZEval operator+ (const XYval &rs) { XYZEval ls = *this; ls.x += rs.x; ls.y += rs.y; return ls; } - FI XYZEval operator- (const XYval &rs) const { XYZEval ls = *this; ls.x -= rs.x; ls.y -= rs.y; return ls; } - FI XYZEval operator- (const XYval &rs) { XYZEval ls = *this; ls.x -= rs.x; ls.y -= rs.y; return ls; } - FI XYZEval operator* (const XYval &rs) const { XYZEval ls = *this; ls.x *= rs.x; ls.y *= rs.y; return ls; } - FI XYZEval operator* (const XYval &rs) { XYZEval ls = *this; ls.x *= rs.x; ls.y *= rs.y; return ls; } - FI XYZEval operator/ (const XYval &rs) const { XYZEval ls = *this; ls.x /= rs.x; ls.y /= rs.y; return ls; } - FI XYZEval operator/ (const XYval &rs) { XYZEval ls = *this; ls.x /= rs.x; ls.y /= rs.y; return ls; } - FI XYZEval operator+ (const XYZval &rs) const { XYZval ls = *this; NUM_AXIS_CODE(ls.x += rs.x, ls.y += rs.y, ls.z += rs.z, ls.i += rs.i, ls.j += rs.j, ls.k += rs.k, ls.u += rs.u, ls.v += rs.v, ls.w += rs.w); return ls; } - FI XYZEval operator+ (const XYZval &rs) { XYZval ls = *this; NUM_AXIS_CODE(ls.x += rs.x, ls.y += rs.y, ls.z += rs.z, ls.i += rs.i, ls.j += rs.j, ls.k += rs.k, ls.u += rs.u, ls.v += rs.v, ls.w += rs.w); return ls; } - FI XYZEval operator- (const XYZval &rs) const { XYZval ls = *this; NUM_AXIS_CODE(ls.x -= rs.x, ls.y -= rs.y, ls.z -= rs.z, ls.i -= rs.i, ls.j -= rs.j, ls.k -= rs.k, ls.u -= rs.u, ls.v -= rs.v, ls.w -= rs.w); return ls; } - FI XYZEval operator- (const XYZval &rs) { XYZval ls = *this; NUM_AXIS_CODE(ls.x -= rs.x, ls.y -= rs.y, ls.z -= rs.z, ls.i -= rs.i, ls.j -= rs.j, ls.k -= rs.k, ls.u -= rs.u, ls.v -= rs.v, ls.w -= rs.w); return ls; } - FI XYZEval operator* (const XYZval &rs) const { XYZval ls = *this; NUM_AXIS_CODE(ls.x *= rs.x, ls.y *= rs.y, ls.z *= rs.z, ls.i *= rs.i, ls.j *= rs.j, ls.k *= rs.k, ls.u *= rs.u, ls.v *= rs.v, ls.w *= rs.w); return ls; } - FI XYZEval operator* (const XYZval &rs) { XYZval ls = *this; NUM_AXIS_CODE(ls.x *= rs.x, ls.y *= rs.y, ls.z *= rs.z, ls.i *= rs.i, ls.j *= rs.j, ls.k *= rs.k, ls.u *= rs.u, ls.v *= rs.v, ls.w *= rs.w); return ls; } - FI XYZEval operator/ (const XYZval &rs) const { XYZval ls = *this; NUM_AXIS_CODE(ls.x /= rs.x, ls.y /= rs.y, ls.z /= rs.z, ls.i /= rs.i, ls.j /= rs.j, ls.k /= rs.k, ls.u /= rs.u, ls.v /= rs.v, ls.w /= rs.w); return ls; } - FI XYZEval operator/ (const XYZval &rs) { XYZval ls = *this; NUM_AXIS_CODE(ls.x /= rs.x, ls.y /= rs.y, ls.z /= rs.z, ls.i /= rs.i, ls.j /= rs.j, ls.k /= rs.k, ls.u /= rs.u, ls.v /= rs.v, ls.w /= rs.w); return ls; } - FI XYZEval operator+ (const XYZEval &rs) const { XYZEval ls = *this; LOGICAL_AXIS_CODE(ls.e += rs.e, ls.x += rs.x, ls.y += rs.y, ls.z += rs.z, ls.i += rs.i, ls.j += rs.j, ls.k += rs.k, ls.u += rs.u, ls.v += rs.v, ls.w += rs.w); return ls; } - FI XYZEval operator+ (const XYZEval &rs) { XYZEval ls = *this; LOGICAL_AXIS_CODE(ls.e += rs.e, ls.x += rs.x, ls.y += rs.y, ls.z += rs.z, ls.i += rs.i, ls.j += rs.j, ls.k += rs.k, ls.u += rs.u, ls.v += rs.v, ls.w += rs.w); return ls; } - FI XYZEval operator- (const XYZEval &rs) const { XYZEval ls = *this; LOGICAL_AXIS_CODE(ls.e -= rs.e, ls.x -= rs.x, ls.y -= rs.y, ls.z -= rs.z, ls.i -= rs.i, ls.j -= rs.j, ls.k -= rs.k, ls.u -= rs.u, ls.v -= rs.v, ls.w -= rs.w); return ls; } - FI XYZEval operator- (const XYZEval &rs) { XYZEval ls = *this; LOGICAL_AXIS_CODE(ls.e -= rs.e, ls.x -= rs.x, ls.y -= rs.y, ls.z -= rs.z, ls.i -= rs.i, ls.j -= rs.j, ls.k -= rs.k, ls.u -= rs.u, ls.v -= rs.v, ls.w -= rs.w); return ls; } - FI XYZEval operator* (const XYZEval &rs) const { XYZEval ls = *this; LOGICAL_AXIS_CODE(ls.e *= rs.e, ls.x *= rs.x, ls.y *= rs.y, ls.z *= rs.z, ls.i *= rs.i, ls.j *= rs.j, ls.k *= rs.k, ls.u *= rs.u, ls.v *= rs.v, ls.w *= rs.w); return ls; } - FI XYZEval operator* (const XYZEval &rs) { XYZEval ls = *this; LOGICAL_AXIS_CODE(ls.e *= rs.e, ls.x *= rs.x, ls.y *= rs.y, ls.z *= rs.z, ls.i *= rs.i, ls.j *= rs.j, ls.k *= rs.k, ls.u *= rs.u, ls.v *= rs.v, ls.w *= rs.w); return ls; } - FI XYZEval operator/ (const XYZEval &rs) const { XYZEval ls = *this; LOGICAL_AXIS_CODE(ls.e /= rs.e, ls.x /= rs.x, ls.y /= rs.y, ls.z /= rs.z, ls.i /= rs.i, ls.j /= rs.j, ls.k /= rs.k, ls.u /= rs.u, ls.v /= rs.v, ls.w /= rs.w); return ls; } - FI XYZEval operator/ (const XYZEval &rs) { XYZEval ls = *this; LOGICAL_AXIS_CODE(ls.e /= rs.e, ls.x /= rs.x, ls.y /= rs.y, ls.z /= rs.z, ls.i /= rs.i, ls.j /= rs.j, ls.k /= rs.k, ls.u /= rs.u, ls.v /= rs.v, ls.w /= rs.w); return ls; } - FI XYZEval operator* (const float &v) const { XYZEval ls = *this; LOGICAL_AXIS_CODE(ls.e *= v, ls.x *= v, ls.y *= v, ls.z *= v, ls.i *= v, ls.j *= v, ls.k *= v, ls.u *= v, ls.v *= v, ls.w *= v ); return ls; } - FI XYZEval operator* (const float &v) { XYZEval ls = *this; LOGICAL_AXIS_CODE(ls.e *= v, ls.x *= v, ls.y *= v, ls.z *= v, ls.i *= v, ls.j *= v, ls.k *= v, ls.u *= v, ls.v *= v, ls.w *= v ); return ls; } - FI XYZEval operator* (const int &v) const { XYZEval ls = *this; LOGICAL_AXIS_CODE(ls.e *= v, ls.x *= v, ls.y *= v, ls.z *= v, ls.i *= v, ls.j *= v, ls.k *= v, ls.u *= v, ls.v *= v, ls.w *= v ); return ls; } - FI XYZEval operator* (const int &v) { XYZEval ls = *this; LOGICAL_AXIS_CODE(ls.e *= v, ls.x *= v, ls.y *= v, ls.z *= v, ls.i *= v, ls.j *= v, ls.k *= v, ls.u *= v, ls.v *= v, ls.w *= v ); return ls; } - FI XYZEval operator/ (const float &v) const { XYZEval ls = *this; LOGICAL_AXIS_CODE(ls.e /= v, ls.x /= v, ls.y /= v, ls.z /= v, ls.i /= v, ls.j /= v, ls.k /= v, ls.u /= v, ls.v /= v, ls.w /= v ); return ls; } - FI XYZEval operator/ (const float &v) { XYZEval ls = *this; LOGICAL_AXIS_CODE(ls.e /= v, ls.x /= v, ls.y /= v, ls.z /= v, ls.i /= v, ls.j /= v, ls.k /= v, ls.u /= v, ls.v /= v, ls.w /= v ); return ls; } - FI XYZEval operator/ (const int &v) const { XYZEval ls = *this; LOGICAL_AXIS_CODE(ls.e /= v, ls.x /= v, ls.y /= v, ls.z /= v, ls.i /= v, ls.j /= v, ls.k /= v, ls.u /= v, ls.v /= v, ls.w /= v ); return ls; } - FI XYZEval operator/ (const int &v) { XYZEval ls = *this; LOGICAL_AXIS_CODE(ls.e /= v, ls.x /= v, ls.y /= v, ls.z /= v, ls.i /= v, ls.j /= v, ls.k /= v, ls.u /= v, ls.v /= v, ls.w /= v ); return ls; } - FI XYZEval operator>>(const int &v) const { XYZEval ls = *this; LOGICAL_AXIS_CODE(_RS(ls.e), _RS(ls.x), _RS(ls.y), _RS(ls.z), _RS(ls.i), _RS(ls.j), _RS(ls.k), _RS(ls.u), _RS(ls.v), _RS(ls.w) ); return ls; } - FI XYZEval operator>>(const int &v) { XYZEval ls = *this; LOGICAL_AXIS_CODE(_RS(ls.e), _RS(ls.x), _RS(ls.y), _RS(ls.z), _RS(ls.i), _RS(ls.j), _RS(ls.k), _RS(ls.u), _RS(ls.v), _RS(ls.w) ); return ls; } - FI XYZEval operator<<(const int &v) const { XYZEval ls = *this; LOGICAL_AXIS_CODE(_LS(ls.e), _LS(ls.x), _LS(ls.y), _LS(ls.z), _LS(ls.i), _LS(ls.j), _LS(ls.k), _LS(ls.u), _LS(ls.v), _LS(ls.w) ); return ls; } - FI XYZEval operator<<(const int &v) { XYZEval ls = *this; LOGICAL_AXIS_CODE(_LS(ls.e), _LS(ls.x), _LS(ls.y), _LS(ls.z), _LS(ls.i), _LS(ls.j), _LS(ls.k), _LS(ls.u), _LS(ls.v), _LS(ls.w) ); return ls; } - FI const XYZEval operator-() const { return LOGICAL_AXIS_ARRAY(-e, -x, -y, -z, -i, -j, -k, -u, -v, -w); } - FI XYZEval operator-() { return LOGICAL_AXIS_ARRAY(-e, -x, -y, -z, -i, -j, -k, -u, -v, -w); } + FI XYZEval operator+ (const XYval &rs) const { XYZEval ls = *this; ls.x += rs.x; ls.y += rs.y; return ls; } + FI XYZEval operator+ (const XYval &rs) { XYZEval ls = *this; ls.x += rs.x; ls.y += rs.y; return ls; } + FI XYZEval operator- (const XYval &rs) const { XYZEval ls = *this; ls.x -= rs.x; ls.y -= rs.y; return ls; } + FI XYZEval operator- (const XYval &rs) { XYZEval ls = *this; ls.x -= rs.x; ls.y -= rs.y; return ls; } + FI XYZEval operator* (const XYval &rs) const { XYZEval ls = *this; ls.x *= rs.x; ls.y *= rs.y; return ls; } + FI XYZEval operator* (const XYval &rs) { XYZEval ls = *this; ls.x *= rs.x; ls.y *= rs.y; return ls; } + FI XYZEval operator/ (const XYval &rs) const { XYZEval ls = *this; ls.x /= rs.x; ls.y /= rs.y; return ls; } + FI XYZEval operator/ (const XYval &rs) { XYZEval ls = *this; ls.x /= rs.x; ls.y /= rs.y; return ls; } + FI XYZEval operator+ (const XYZval &rs) const { XYZval ls = *this; NUM_AXIS_CODE(ls.x += rs.x, ls.y += rs.y, ls.z += rs.z, ls.i += rs.i, ls.j += rs.j, ls.k += rs.k, ls.u += rs.u, ls.v += rs.v, ls.w += rs.w); return ls; } + FI XYZEval operator+ (const XYZval &rs) { XYZval ls = *this; NUM_AXIS_CODE(ls.x += rs.x, ls.y += rs.y, ls.z += rs.z, ls.i += rs.i, ls.j += rs.j, ls.k += rs.k, ls.u += rs.u, ls.v += rs.v, ls.w += rs.w); return ls; } + FI XYZEval operator- (const XYZval &rs) const { XYZval ls = *this; NUM_AXIS_CODE(ls.x -= rs.x, ls.y -= rs.y, ls.z -= rs.z, ls.i -= rs.i, ls.j -= rs.j, ls.k -= rs.k, ls.u -= rs.u, ls.v -= rs.v, ls.w -= rs.w); return ls; } + FI XYZEval operator- (const XYZval &rs) { XYZval ls = *this; NUM_AXIS_CODE(ls.x -= rs.x, ls.y -= rs.y, ls.z -= rs.z, ls.i -= rs.i, ls.j -= rs.j, ls.k -= rs.k, ls.u -= rs.u, ls.v -= rs.v, ls.w -= rs.w); return ls; } + FI XYZEval operator* (const XYZval &rs) const { XYZval ls = *this; NUM_AXIS_CODE(ls.x *= rs.x, ls.y *= rs.y, ls.z *= rs.z, ls.i *= rs.i, ls.j *= rs.j, ls.k *= rs.k, ls.u *= rs.u, ls.v *= rs.v, ls.w *= rs.w); return ls; } + FI XYZEval operator* (const XYZval &rs) { XYZval ls = *this; NUM_AXIS_CODE(ls.x *= rs.x, ls.y *= rs.y, ls.z *= rs.z, ls.i *= rs.i, ls.j *= rs.j, ls.k *= rs.k, ls.u *= rs.u, ls.v *= rs.v, ls.w *= rs.w); return ls; } + FI XYZEval operator/ (const XYZval &rs) const { XYZval ls = *this; NUM_AXIS_CODE(ls.x /= rs.x, ls.y /= rs.y, ls.z /= rs.z, ls.i /= rs.i, ls.j /= rs.j, ls.k /= rs.k, ls.u /= rs.u, ls.v /= rs.v, ls.w /= rs.w); return ls; } + FI XYZEval operator/ (const XYZval &rs) { XYZval ls = *this; NUM_AXIS_CODE(ls.x /= rs.x, ls.y /= rs.y, ls.z /= rs.z, ls.i /= rs.i, ls.j /= rs.j, ls.k /= rs.k, ls.u /= rs.u, ls.v /= rs.v, ls.w /= rs.w); return ls; } + FI XYZEval operator+ (const XYZEval &rs) const { XYZEval ls = *this; LOGICAL_AXIS_CODE(ls.e += rs.e, ls.x += rs.x, ls.y += rs.y, ls.z += rs.z, ls.i += rs.i, ls.j += rs.j, ls.k += rs.k, ls.u += rs.u, ls.v += rs.v, ls.w += rs.w); return ls; } + FI XYZEval operator+ (const XYZEval &rs) { XYZEval ls = *this; LOGICAL_AXIS_CODE(ls.e += rs.e, ls.x += rs.x, ls.y += rs.y, ls.z += rs.z, ls.i += rs.i, ls.j += rs.j, ls.k += rs.k, ls.u += rs.u, ls.v += rs.v, ls.w += rs.w); return ls; } + FI XYZEval operator- (const XYZEval &rs) const { XYZEval ls = *this; LOGICAL_AXIS_CODE(ls.e -= rs.e, ls.x -= rs.x, ls.y -= rs.y, ls.z -= rs.z, ls.i -= rs.i, ls.j -= rs.j, ls.k -= rs.k, ls.u -= rs.u, ls.v -= rs.v, ls.w -= rs.w); return ls; } + FI XYZEval operator- (const XYZEval &rs) { XYZEval ls = *this; LOGICAL_AXIS_CODE(ls.e -= rs.e, ls.x -= rs.x, ls.y -= rs.y, ls.z -= rs.z, ls.i -= rs.i, ls.j -= rs.j, ls.k -= rs.k, ls.u -= rs.u, ls.v -= rs.v, ls.w -= rs.w); return ls; } + FI XYZEval operator* (const XYZEval &rs) const { XYZEval ls = *this; LOGICAL_AXIS_CODE(ls.e *= rs.e, ls.x *= rs.x, ls.y *= rs.y, ls.z *= rs.z, ls.i *= rs.i, ls.j *= rs.j, ls.k *= rs.k, ls.u *= rs.u, ls.v *= rs.v, ls.w *= rs.w); return ls; } + FI XYZEval operator* (const XYZEval &rs) { XYZEval ls = *this; LOGICAL_AXIS_CODE(ls.e *= rs.e, ls.x *= rs.x, ls.y *= rs.y, ls.z *= rs.z, ls.i *= rs.i, ls.j *= rs.j, ls.k *= rs.k, ls.u *= rs.u, ls.v *= rs.v, ls.w *= rs.w); return ls; } + FI XYZEval operator/ (const XYZEval &rs) const { XYZEval ls = *this; LOGICAL_AXIS_CODE(ls.e /= rs.e, ls.x /= rs.x, ls.y /= rs.y, ls.z /= rs.z, ls.i /= rs.i, ls.j /= rs.j, ls.k /= rs.k, ls.u /= rs.u, ls.v /= rs.v, ls.w /= rs.w); return ls; } + FI XYZEval operator/ (const XYZEval &rs) { XYZEval ls = *this; LOGICAL_AXIS_CODE(ls.e /= rs.e, ls.x /= rs.x, ls.y /= rs.y, ls.z /= rs.z, ls.i /= rs.i, ls.j /= rs.j, ls.k /= rs.k, ls.u /= rs.u, ls.v /= rs.v, ls.w /= rs.w); return ls; } + FI XYZEval operator* (const float &p) const { XYZEval ls = *this; LOGICAL_AXIS_CODE(ls.e *= p, ls.x *= p, ls.y *= p, ls.z *= p, ls.i *= p, ls.j *= p, ls.k *= p, ls.u *= p, ls.v *= p, ls.w *= p ); return ls; } + FI XYZEval operator* (const float &p) { XYZEval ls = *this; LOGICAL_AXIS_CODE(ls.e *= p, ls.x *= p, ls.y *= p, ls.z *= p, ls.i *= p, ls.j *= p, ls.k *= p, ls.u *= p, ls.v *= p, ls.w *= p ); return ls; } + FI XYZEval operator* (const int &p) const { XYZEval ls = *this; LOGICAL_AXIS_CODE(ls.e *= p, ls.x *= p, ls.y *= p, ls.z *= p, ls.i *= p, ls.j *= p, ls.k *= p, ls.u *= p, ls.v *= p, ls.w *= p ); return ls; } + FI XYZEval operator* (const int &p) { XYZEval ls = *this; LOGICAL_AXIS_CODE(ls.e *= p, ls.x *= p, ls.y *= p, ls.z *= p, ls.i *= p, ls.j *= p, ls.k *= p, ls.u *= p, ls.v *= p, ls.w *= p ); return ls; } + FI XYZEval operator/ (const float &p) const { XYZEval ls = *this; LOGICAL_AXIS_CODE(ls.e /= p, ls.x /= p, ls.y /= p, ls.z /= p, ls.i /= p, ls.j /= p, ls.k /= p, ls.u /= p, ls.v /= p, ls.w /= p ); return ls; } + FI XYZEval operator/ (const float &p) { XYZEval ls = *this; LOGICAL_AXIS_CODE(ls.e /= p, ls.x /= p, ls.y /= p, ls.z /= p, ls.i /= p, ls.j /= p, ls.k /= p, ls.u /= p, ls.v /= p, ls.w /= p ); return ls; } + FI XYZEval operator/ (const int &p) const { XYZEval ls = *this; LOGICAL_AXIS_CODE(ls.e /= p, ls.x /= p, ls.y /= p, ls.z /= p, ls.i /= p, ls.j /= p, ls.k /= p, ls.u /= p, ls.v /= p, ls.w /= p ); return ls; } + FI XYZEval operator/ (const int &p) { XYZEval ls = *this; LOGICAL_AXIS_CODE(ls.e /= p, ls.x /= p, ls.y /= p, ls.z /= p, ls.i /= p, ls.j /= p, ls.k /= p, ls.u /= p, ls.v /= p, ls.w /= p ); return ls; } + FI XYZEval operator>>(const int &p) const { XYZEval ls = *this; LOGICAL_AXIS_CODE(_RS(ls.e), _RS(ls.x), _RS(ls.y), _RS(ls.z), _RS(ls.i), _RS(ls.j), _RS(ls.k), _RS(ls.u), _RS(ls.v), _RS(ls.w) ); return ls; } + FI XYZEval operator>>(const int &p) { XYZEval ls = *this; LOGICAL_AXIS_CODE(_RS(ls.e), _RS(ls.x), _RS(ls.y), _RS(ls.z), _RS(ls.i), _RS(ls.j), _RS(ls.k), _RS(ls.u), _RS(ls.v), _RS(ls.w) ); return ls; } + FI XYZEval operator<<(const int &p) const { XYZEval ls = *this; LOGICAL_AXIS_CODE(_LS(ls.e), _LS(ls.x), _LS(ls.y), _LS(ls.z), _LS(ls.i), _LS(ls.j), _LS(ls.k), _LS(ls.u), _LS(ls.v), _LS(ls.w) ); return ls; } + FI XYZEval operator<<(const int &p) { XYZEval ls = *this; LOGICAL_AXIS_CODE(_LS(ls.e), _LS(ls.x), _LS(ls.y), _LS(ls.z), _LS(ls.i), _LS(ls.j), _LS(ls.k), _LS(ls.u), _LS(ls.v), _LS(ls.w) ); return ls; } + FI const XYZEval operator-() const { return LOGICAL_AXIS_ARRAY(-e, -x, -y, -z, -i, -j, -k, -u, -v, -w); } + FI XYZEval operator-() { return LOGICAL_AXIS_ARRAY(-e, -x, -y, -z, -i, -j, -k, -u, -v, -w); } // Modifier operators - FI XYZEval& operator+=(const XYval &rs) { x += rs.x; y += rs.y; return *this; } - FI XYZEval& operator-=(const XYval &rs) { x -= rs.x; y -= rs.y; return *this; } - FI XYZEval& operator*=(const XYval &rs) { x *= rs.x; y *= rs.y; return *this; } - FI XYZEval& operator/=(const XYval &rs) { x /= rs.x; y /= rs.y; return *this; } - FI XYZEval& operator+=(const XYZval &rs) { NUM_AXIS_CODE(x += rs.x, y += rs.y, z += rs.z, i += rs.i, j += rs.j, k += rs.k, u += rs.u, v += rs.v, w += rs.w); return *this; } - FI XYZEval& operator-=(const XYZval &rs) { NUM_AXIS_CODE(x -= rs.x, y -= rs.y, z -= rs.z, i -= rs.i, j -= rs.j, k -= rs.k, u -= rs.u, v -= rs.v, w -= rs.w); return *this; } - FI XYZEval& operator*=(const XYZval &rs) { NUM_AXIS_CODE(x *= rs.x, y *= rs.y, z *= rs.z, i *= rs.i, j *= rs.j, k *= rs.k, u *= rs.u, v *= rs.v, w *= rs.w); return *this; } - FI XYZEval& operator/=(const XYZval &rs) { NUM_AXIS_CODE(x /= rs.x, y /= rs.y, z /= rs.z, i /= rs.i, j /= rs.j, k /= rs.k, u /= rs.u, v /= rs.v, w /= rs.w); return *this; } - FI XYZEval& operator+=(const XYZEval &rs) { LOGICAL_AXIS_CODE(e += rs.e, x += rs.x, y += rs.y, z += rs.z, i += rs.i, j += rs.j, k += rs.k, u += rs.u, v += rs.v, w += rs.w); return *this; } - FI XYZEval& operator-=(const XYZEval &rs) { LOGICAL_AXIS_CODE(e -= rs.e, x -= rs.x, y -= rs.y, z -= rs.z, i -= rs.i, j -= rs.j, k -= rs.k, u -= rs.u, v -= rs.v, w -= rs.w); return *this; } - FI XYZEval& operator*=(const XYZEval &rs) { LOGICAL_AXIS_CODE(e *= rs.e, x *= rs.x, y *= rs.y, z *= rs.z, i *= rs.i, j *= rs.j, k *= rs.k, u *= rs.u, v *= rs.v, w *= rs.w); return *this; } - FI XYZEval& operator/=(const XYZEval &rs) { LOGICAL_AXIS_CODE(e /= rs.e, x /= rs.x, y /= rs.y, z /= rs.z, i /= rs.i, j /= rs.j, k /= rs.k, u /= rs.u, v /= rs.v, w /= rs.w); return *this; } - FI XYZEval& operator*=(const T &v) { LOGICAL_AXIS_CODE(e *= v, x *= v, y *= v, z *= v, i *= v, j *= v, k *= v, u *= v, v *= v, w *= v); return *this; } - FI XYZEval& operator>>=(const int &v) { LOGICAL_AXIS_CODE(_RS(e), _RS(x), _RS(y), _RS(z), _RS(i), _RS(j), _RS(k), _RS(u), _RS(v), _RS(w)); return *this; } - FI XYZEval& operator<<=(const int &v) { LOGICAL_AXIS_CODE(_LS(e), _LS(x), _LS(y), _LS(z), _LS(i), _LS(j), _LS(k), _LS(u), _LS(v), _LS(w)); return *this; } + FI XYZEval& operator+=(const XYval &rs) { x += rs.x; y += rs.y; return *this; } + FI XYZEval& operator-=(const XYval &rs) { x -= rs.x; y -= rs.y; return *this; } + FI XYZEval& operator*=(const XYval &rs) { x *= rs.x; y *= rs.y; return *this; } + FI XYZEval& operator/=(const XYval &rs) { x /= rs.x; y /= rs.y; return *this; } + FI XYZEval& operator+=(const XYZval &rs) { NUM_AXIS_CODE(x += rs.x, y += rs.y, z += rs.z, i += rs.i, j += rs.j, k += rs.k, u += rs.u, v += rs.v, w += rs.w); return *this; } + FI XYZEval& operator-=(const XYZval &rs) { NUM_AXIS_CODE(x -= rs.x, y -= rs.y, z -= rs.z, i -= rs.i, j -= rs.j, k -= rs.k, u -= rs.u, v -= rs.v, w -= rs.w); return *this; } + FI XYZEval& operator*=(const XYZval &rs) { NUM_AXIS_CODE(x *= rs.x, y *= rs.y, z *= rs.z, i *= rs.i, j *= rs.j, k *= rs.k, u *= rs.u, v *= rs.v, w *= rs.w); return *this; } + FI XYZEval& operator/=(const XYZval &rs) { NUM_AXIS_CODE(x /= rs.x, y /= rs.y, z /= rs.z, i /= rs.i, j /= rs.j, k /= rs.k, u /= rs.u, v /= rs.v, w /= rs.w); return *this; } + FI XYZEval& operator+=(const XYZEval &rs) { LOGICAL_AXIS_CODE(e += rs.e, x += rs.x, y += rs.y, z += rs.z, i += rs.i, j += rs.j, k += rs.k, u += rs.u, v += rs.v, w += rs.w); return *this; } + FI XYZEval& operator-=(const XYZEval &rs) { LOGICAL_AXIS_CODE(e -= rs.e, x -= rs.x, y -= rs.y, z -= rs.z, i -= rs.i, j -= rs.j, k -= rs.k, u -= rs.u, v -= rs.v, w -= rs.w); return *this; } + FI XYZEval& operator*=(const XYZEval &rs) { LOGICAL_AXIS_CODE(e *= rs.e, x *= rs.x, y *= rs.y, z *= rs.z, i *= rs.i, j *= rs.j, k *= rs.k, u *= rs.u, v *= rs.v, w *= rs.w); return *this; } + FI XYZEval& operator/=(const XYZEval &rs) { LOGICAL_AXIS_CODE(e /= rs.e, x /= rs.x, y /= rs.y, z /= rs.z, i /= rs.i, j /= rs.j, k /= rs.k, u /= rs.u, v /= rs.v, w /= rs.w); return *this; } + FI XYZEval& operator*=(const T &p) { LOGICAL_AXIS_CODE(e *= p, x *= p, y *= p, z *= p, i *= p, j *= p, k *= p, u *= p, v *= p, w *= p); return *this; } + FI XYZEval& operator>>=(const int &p) { LOGICAL_AXIS_CODE(_RS(e), _RS(x), _RS(y), _RS(z), _RS(i), _RS(j), _RS(k), _RS(u), _RS(v), _RS(w)); return *this; } + FI XYZEval& operator<<=(const int &p) { LOGICAL_AXIS_CODE(_LS(e), _LS(x), _LS(y), _LS(z), _LS(i), _LS(j), _LS(k), _LS(u), _LS(v), _LS(w)); return *this; } // Exact comparisons. For floats a "NEAR" operation may be better. - FI bool operator==(const XYZval &rs) { return true NUM_AXIS_GANG(&& x == rs.x, && y == rs.y, && z == rs.z, && i == rs.i, && j == rs.j, && k == rs.k, && u == rs.u, && v == rs.v, && w == rs.w); } - FI bool operator==(const XYZval &rs) const { return true NUM_AXIS_GANG(&& x == rs.x, && y == rs.y, && z == rs.z, && i == rs.i, && j == rs.j, && k == rs.k, && u == rs.u, && v == rs.v, && w == rs.w); } - FI bool operator==(const XYZEval &rs) { return true LOGICAL_AXIS_GANG(&& e == rs.e, && x == rs.x, && y == rs.y, && z == rs.z, && i == rs.i, && j == rs.j, && k == rs.k, && u == rs.u, && v == rs.v, && w == rs.w); } - FI bool operator==(const XYZEval &rs) const { return true LOGICAL_AXIS_GANG(&& e == rs.e, && x == rs.x, && y == rs.y, && z == rs.z, && i == rs.i, && j == rs.j, && k == rs.k, && u == rs.u, && v == rs.v, && w == rs.w); } - FI bool operator!=(const XYZval &rs) { return !operator==(rs); } - FI bool operator!=(const XYZval &rs) const { return !operator==(rs); } - FI bool operator!=(const XYZEval &rs) { return !operator==(rs); } - FI bool operator!=(const XYZEval &rs) const { return !operator==(rs); } + FI bool operator==(const XYZval &rs) const { return true NUM_AXIS_GANG(&& x == rs.x, && y == rs.y, && z == rs.z, && i == rs.i, && j == rs.j, && k == rs.k, && u == rs.u, && v == rs.v, && w == rs.w); } + FI bool operator==(const XYZEval &rs) const { return true LOGICAL_AXIS_GANG(&& e == rs.e, && x == rs.x, && y == rs.y, && z == rs.z, && i == rs.i, && j == rs.j, && k == rs.k, && u == rs.u, && v == rs.v, && w == rs.w); } + FI bool operator!=(const XYZval &rs) const { return !operator==(rs); } + FI bool operator!=(const XYZEval &rs) const { return !operator==(rs); } }; #undef _RECIP diff --git a/Marlin/src/feature/bedlevel/bedlevel.cpp b/Marlin/src/feature/bedlevel/bedlevel.cpp index 2207884c36..1658b536d3 100644 --- a/Marlin/src/feature/bedlevel/bedlevel.cpp +++ b/Marlin/src/feature/bedlevel/bedlevel.cpp @@ -75,9 +75,9 @@ void set_bed_leveling_enabled(const bool enable/*=true*/) { planner.synchronize(); // Get the corrected leveled / unleveled position - planner.apply_modifiers(current_position); // Physical position with all modifiers - planner.leveling_active ^= true; // Toggle leveling between apply and unapply - planner.unapply_modifiers(current_position); // Logical position with modifiers removed + planner.apply_modifiers(current_position, true); // Physical position with all modifiers + planner.leveling_active ^= true; // Toggle leveling between apply and unapply + planner.unapply_modifiers(current_position, true); // Logical position with modifiers removed sync_plan_position(); _report_leveling(); diff --git a/Marlin/src/feature/bedlevel/ubl/ubl_G29.cpp b/Marlin/src/feature/bedlevel/ubl/ubl_G29.cpp index f1e88006ff..d6cb0b762f 100644 --- a/Marlin/src/feature/bedlevel/ubl/ubl_G29.cpp +++ b/Marlin/src/feature/bedlevel/ubl/ubl_G29.cpp @@ -407,7 +407,7 @@ void unified_bed_leveling::G29() { z_values[x][x2] += 9.999f; // We want the altered line several mesh points thick #if ENABLED(EXTENSIBLE_UI) ExtUI::onMeshUpdate(x, x, z_values[x][x]); - ExtUI::onMeshUpdate(x, (x2), z_values[x][x2]); + ExtUI::onMeshUpdate(x, x2, z_values[x][x2]); #endif } break; diff --git a/Marlin/src/feature/e_parser.cpp b/Marlin/src/feature/e_parser.cpp index d98afcfee7..cfe0956aa7 100644 --- a/Marlin/src/feature/e_parser.cpp +++ b/Marlin/src/feature/e_parser.cpp @@ -33,6 +33,9 @@ // Static data members bool EmergencyParser::killed_by_M112, // = false EmergencyParser::quickstop_by_M410, + #if ENABLED(SDSUPPORT) + EmergencyParser::sd_abort_by_M524, + #endif EmergencyParser::enabled; #if ENABLED(HOST_PROMPT_SUPPORT) diff --git a/Marlin/src/feature/e_parser.h b/Marlin/src/feature/e_parser.h index fda1ba144b..3a15a7ffa0 100644 --- a/Marlin/src/feature/e_parser.h +++ b/Marlin/src/feature/e_parser.h @@ -49,7 +49,7 @@ class EmergencyParser { public: - // Currently looking for: M108, M112, M410, M876 S[0-9], S000, P000, R000 + // Currently looking for: M108, M112, M410, M524, M876 S[0-9], S000, P000, R000 enum State : uint8_t { EP_RESET, EP_N, @@ -58,6 +58,9 @@ public: EP_M10, EP_M108, EP_M11, EP_M112, EP_M4, EP_M41, EP_M410, + #if ENABLED(SDSUPPORT) + EP_M5, EP_M52, EP_M524, + #endif #if ENABLED(HOST_PROMPT_SUPPORT) EP_M8, EP_M87, EP_M876, EP_M876S, EP_M876SN, #endif @@ -76,6 +79,10 @@ public: static bool killed_by_M112; static bool quickstop_by_M410; + #if ENABLED(SDSUPPORT) + static bool sd_abort_by_M524; + #endif + #if ENABLED(HOST_PROMPT_SUPPORT) static uint8_t M876_reason; #endif @@ -145,6 +152,9 @@ public: case ' ': break; case '1': state = EP_M1; break; case '4': state = EP_M4; break; + #if ENABLED(SDSUPPORT) + case '5': state = EP_M5; break; + #endif #if ENABLED(HOST_PROMPT_SUPPORT) case '8': state = EP_M8; break; #endif @@ -165,6 +175,11 @@ public: case EP_M4: state = (c == '1') ? EP_M41 : EP_IGNORE; break; case EP_M41: state = (c == '0') ? EP_M410 : EP_IGNORE; break; + #if ENABLED(SDSUPPORT) + case EP_M5: state = (c == '2') ? EP_M52 : EP_IGNORE; break; + case EP_M52: state = (c == '4') ? EP_M524 : EP_IGNORE; break; + #endif + #if ENABLED(HOST_PROMPT_SUPPORT) case EP_M8: state = (c == '7') ? EP_M87 : EP_IGNORE; break; @@ -200,6 +215,9 @@ public: case EP_M108: wait_for_user = wait_for_heatup = false; break; case EP_M112: killed_by_M112 = true; break; case EP_M410: quickstop_by_M410 = true; break; + #if ENABLED(SDSUPPORT) + case EP_M524: sd_abort_by_M524 = true; break; + #endif #if ENABLED(HOST_PROMPT_SUPPORT) case EP_M876SN: hostui.handle_response(M876_reason); break; #endif diff --git a/Marlin/src/feature/host_actions.cpp b/Marlin/src/feature/host_actions.cpp index 3385076701..93bb915863 100644 --- a/Marlin/src/feature/host_actions.cpp +++ b/Marlin/src/feature/host_actions.cpp @@ -111,20 +111,29 @@ void HostUI::action(FSTR_P const fstr, const bool eol) { if (eol) SERIAL_EOL(); } - void HostUI::prompt_plus(FSTR_P const ptype, FSTR_P const fstr, const char extra_char/*='\0'*/) { + void HostUI::prompt_plus(const bool pgm, FSTR_P const ptype, const char * const str, const char extra_char/*='\0'*/) { prompt(ptype, false); PORT_REDIRECT(SerialMask::All); SERIAL_CHAR(' '); - SERIAL_ECHOF(fstr); + if (pgm) + SERIAL_ECHOPGM_P(str); + else + SERIAL_ECHO(str); if (extra_char != '\0') SERIAL_CHAR(extra_char); SERIAL_EOL(); } + void HostUI::prompt_begin(const PromptReason reason, FSTR_P const fstr, const char extra_char/*='\0'*/) { prompt_end(); host_prompt_reason = reason; prompt_plus(F("begin"), fstr, extra_char); } - void HostUI::prompt_button(FSTR_P const fstr) { prompt_plus(F("button"), fstr); } + void HostUI::prompt_begin(const PromptReason reason, const char * const cstr, const char extra_char/*='\0'*/) { + prompt_end(); + host_prompt_reason = reason; + prompt_plus(F("begin"), cstr, extra_char); + } + void HostUI::prompt_end() { prompt(F("end")); } void HostUI::prompt_show() { prompt(F("show")); } @@ -133,14 +142,26 @@ void HostUI::action(FSTR_P const fstr, const bool eol) { if (btn2) prompt_button(btn2); prompt_show(); } + + void HostUI::prompt_button(FSTR_P const fstr) { prompt_plus(F("button"), fstr); } + void HostUI::prompt_button(const char * const cstr) { prompt_plus(F("button"), cstr); } + void HostUI::prompt_do(const PromptReason reason, FSTR_P const fstr, FSTR_P const btn1/*=nullptr*/, FSTR_P const btn2/*=nullptr*/) { prompt_begin(reason, fstr); _prompt_show(btn1, btn2); } + void HostUI::prompt_do(const PromptReason reason, const char * const cstr, FSTR_P const btn1/*=nullptr*/, FSTR_P const btn2/*=nullptr*/) { + prompt_begin(reason, cstr); + _prompt_show(btn1, btn2); + } void HostUI::prompt_do(const PromptReason reason, FSTR_P const fstr, const char extra_char, FSTR_P const btn1/*=nullptr*/, FSTR_P const btn2/*=nullptr*/) { prompt_begin(reason, fstr, extra_char); _prompt_show(btn1, btn2); } + void HostUI::prompt_do(const PromptReason reason, const char * const cstr, const char extra_char, FSTR_P const btn1/*=nullptr*/, FSTR_P const btn2/*=nullptr*/) { + prompt_begin(reason, cstr, extra_char); + _prompt_show(btn1, btn2); + } #if ENABLED(ADVANCED_PAUSE_FEATURE) void HostUI::filament_load_prompt() { diff --git a/Marlin/src/feature/host_actions.h b/Marlin/src/feature/host_actions.h index 41d66b82ec..3f75562398 100644 --- a/Marlin/src/feature/host_actions.h +++ b/Marlin/src/feature/host_actions.h @@ -79,7 +79,14 @@ class HostUI { #if ENABLED(HOST_PROMPT_SUPPORT) private: static void prompt(FSTR_P const ptype, const bool eol=true); - static void prompt_plus(FSTR_P const ptype, FSTR_P const fstr, const char extra_char='\0'); + static void prompt_plus(const bool pgm, FSTR_P const ptype, const char * const str, const char extra_char='\0'); + static void prompt_plus(FSTR_P const ptype, FSTR_P const fstr, const char extra_char='\0') { + prompt_plus(true, ptype, FTOP(fstr), extra_char); + } + static void prompt_plus(FSTR_P const ptype, const char * const cstr, const char extra_char='\0') { + prompt_plus(false, ptype, cstr, extra_char); + } + static void prompt_show(); static void _prompt_show(FSTR_P const btn1, FSTR_P const btn2); @@ -93,10 +100,17 @@ class HostUI { static void notify(const char * const message); static void prompt_begin(const PromptReason reason, FSTR_P const fstr, const char extra_char='\0'); - static void prompt_button(FSTR_P const fstr); + static void prompt_begin(const PromptReason reason, const char * const cstr, const char extra_char='\0'); static void prompt_end(); + + static void prompt_button(FSTR_P const fstr); + static void prompt_button(const char * const cstr); + static void prompt_do(const PromptReason reason, FSTR_P const pstr, FSTR_P const btn1=nullptr, FSTR_P const btn2=nullptr); + static void prompt_do(const PromptReason reason, const char * const cstr, FSTR_P const btn1=nullptr, FSTR_P const btn2=nullptr); static void prompt_do(const PromptReason reason, FSTR_P const pstr, const char extra_char, FSTR_P const btn1=nullptr, FSTR_P const btn2=nullptr); + static void prompt_do(const PromptReason reason, const char * const cstr, const char extra_char, FSTR_P const btn1=nullptr, FSTR_P const btn2=nullptr); + static void prompt_open(const PromptReason reason, FSTR_P const pstr, FSTR_P const btn1=nullptr, FSTR_P const btn2=nullptr) { if (host_prompt_reason == PROMPT_NOT_DEFINED) prompt_do(reason, pstr, btn1, btn2); } diff --git a/Marlin/src/feature/mmu/mmu2.cpp b/Marlin/src/feature/mmu/mmu2.cpp index 227a2308eb..75cb17cbf1 100644 --- a/Marlin/src/feature/mmu/mmu2.cpp +++ b/Marlin/src/feature/mmu/mmu2.cpp @@ -54,7 +54,8 @@ MMU2 mmu2; #define MMU_CMD_TIMEOUT 45000UL // 45s timeout for mmu commands (except P0) #define MMU_P0_TIMEOUT 3000UL // Timeout for P0 command: 3seconds -#define MMU2_COMMAND(S) tx_str(F(S "\n")) +#define MMU2_SEND(S) tx_str(F(S "\n")) +#define MMU2_RECV(S) rx_str(F(S "\n")) #if ENABLED(MMU_EXTRUDER_SENSOR) uint8_t mmu_idl_sens = 0; @@ -131,7 +132,7 @@ void MMU2::reset() { safe_delay(20); WRITE(MMU2_RST_PIN, HIGH); #else - MMU2_COMMAND("X0"); // Send soft reset + MMU2_SEND("X0"); // Send soft reset #endif } @@ -157,11 +158,9 @@ void MMU2::mmu_loop() { case -1: if (rx_start()) { prev_P0_request = millis(); // Initialize finda sensor timeout - DEBUG_ECHOLNPGM("MMU => 'start'"); DEBUG_ECHOLNPGM("MMU <= 'S1'"); - - MMU2_COMMAND("S1"); // Read Version + MMU2_SEND("S1"); // Read Version state = -2; } else if (millis() > 30000) { // 30sec after reset disable MMU @@ -173,10 +172,8 @@ void MMU2::mmu_loop() { case -2: if (rx_ok()) { sscanf(rx_buffer, "%huok\n", &version); - DEBUG_ECHOLNPGM("MMU => ", version, "\nMMU <= 'S2'"); - - MMU2_COMMAND("S2"); // Read Build Number + MMU2_SEND("S2"); // Read Build Number state = -3; } break; @@ -191,14 +188,12 @@ void MMU2::mmu_loop() { #if ENABLED(MMU2_MODE_12V) DEBUG_ECHOLNPGM("MMU <= 'M1'"); - - MMU2_COMMAND("M1"); // Stealth Mode + MMU2_SEND("M1"); // Stealth Mode state = -5; #else DEBUG_ECHOLNPGM("MMU <= 'P0'"); - - MMU2_COMMAND("P0"); // Read FINDA + MMU2_SEND("P0"); // Read FINDA state = -4; #endif } @@ -209,10 +204,8 @@ void MMU2::mmu_loop() { // response to M1 if (rx_ok()) { DEBUG_ECHOLNPGM("MMU => ok"); - DEBUG_ECHOLNPGM("MMU <= 'P0'"); - - MMU2_COMMAND("P0"); // Read FINDA + MMU2_SEND("P0"); // Read FINDA state = -4; } break; @@ -250,14 +243,13 @@ void MMU2::mmu_loop() { else if (cmd == MMU_CMD_C0) { // continue loading DEBUG_ECHOLNPGM("MMU <= 'C0'"); - MMU2_COMMAND("C0"); + MMU2_SEND("C0"); state = 3; // wait for response } else if (cmd == MMU_CMD_U0) { // unload current DEBUG_ECHOLNPGM("MMU <= 'U0'"); - - MMU2_COMMAND("U0"); + MMU2_SEND("U0"); state = 3; // wait for response } else if (WITHIN(cmd, MMU_CMD_E0, MMU_CMD_E0 + EXTRUDERS - 1)) { @@ -270,7 +262,7 @@ void MMU2::mmu_loop() { else if (cmd == MMU_CMD_R0) { // recover after eject DEBUG_ECHOLNPGM("MMU <= 'R0'"); - MMU2_COMMAND("R0"); + MMU2_SEND("R0"); state = 3; // wait for response } else if (WITHIN(cmd, MMU_CMD_F0, MMU_CMD_F0 + EXTRUDERS - 1)) { @@ -285,7 +277,7 @@ void MMU2::mmu_loop() { cmd = MMU_CMD_NONE; } else if (ELAPSED(millis(), prev_P0_request + 300)) { - MMU2_COMMAND("P0"); // Read FINDA + MMU2_SEND("P0"); // Read FINDA state = 2; // wait for response } @@ -314,7 +306,7 @@ void MMU2::mmu_loop() { if (mmu_idl_sens) { if (FILAMENT_PRESENT() && mmu_loading_flag) { DEBUG_ECHOLNPGM("MMU <= 'A'"); - MMU2_COMMAND("A"); // send 'abort' request + MMU2_SEND("A"); // send 'abort' request mmu_idl_sens = 0; DEBUG_ECHOLNPGM("MMU IDLER_SENSOR = 0 - ABORT"); } @@ -327,9 +319,9 @@ void MMU2::mmu_loop() { const bool keep_trying = !mmu2s_triggered && last_cmd == MMU_CMD_C0; if (keep_trying) { // MMU ok received but filament sensor not triggered, retrying... - DEBUG_ECHOLNPGM("MMU => 'ok' (filament not present in gears)"); + DEBUG_ECHOLNPGM("MMU => 'ok' (no filament in gears)"); DEBUG_ECHOLNPGM("MMU <= 'C0' (keep trying)"); - MMU2_COMMAND("C0"); + MMU2_SEND("C0"); } #else constexpr bool keep_trying = false; @@ -361,7 +353,7 @@ void MMU2::mmu_loop() { */ bool MMU2::rx_start() { // check for start message - return rx_str(F("start\n")); + return MMU2_RECV("start"); } /** @@ -440,7 +432,7 @@ void MMU2::clear_rx_buffer() { * Check if we received 'ok' from MMU */ bool MMU2::rx_ok() { - if (rx_str(F("ok\n"))) { + if (MMU2_RECV("ok")) { prev_P0_request = millis(); return true; } @@ -585,7 +577,7 @@ static void mmu2_not_responding() { command(MMU_CMD_T0 + index); manage_response(true, true); mmu_continue_loading(); - command(MMU_CMD_C0); + //command(MMU_CMD_C0); extruder = index; active_extruder = 0; @@ -653,13 +645,34 @@ static void mmu2_not_responding() { } void MMU2::mmu_continue_loading() { + // Try to load the filament a limited number of times + bool fil_present = 0; for (uint8_t i = 0; i < MMU_LOADING_ATTEMPTS_NR; i++) { - DEBUG_ECHOLNPGM("Additional load attempt #", i); - if (FILAMENT_PRESENT()) break; + DEBUG_ECHOLNPGM("Load attempt #", i + 1); + + // Done as soon as filament is present + fil_present = FILAMENT_PRESENT(); + if (fil_present) break; + + // Attempt to load the filament, 1mm at a time, for 3s command(MMU_CMD_C0); + stepper.enable_extruder(); + const millis_t expire_ms = millis() + 3000; + do { + current_position.e += 1; + line_to_current_position(MMU_LOAD_FEEDRATE); + planner.synchronize(); + // When (T0 rx->ok) load is ready, but in fact it did not load + // successfully or an overload created pressure in the extruder. + // Send (C0) to load more and move E_AXIS a little to release pressure. + if ((fil_present = FILAMENT_PRESENT())) MMU2_SEND("A"); + } while (!fil_present && PENDING(millis(), expire_ms)); + stepper.disable_extruder(); manage_response(true, true); } - if (!FILAMENT_PRESENT()) { + + // Was the filament still missing in the last check? + if (!fil_present) { DEBUG_ECHOLNPGM("Filament never reached sensor, runout"); filament_runout(); } @@ -682,7 +695,7 @@ static void mmu2_not_responding() { command(MMU_CMD_T0 + index); manage_response(true, true); command(MMU_CMD_C0); - extruder = index; //filament change is finished + extruder = index; // Filament change is finished active_extruder = 0; stepper.enable_extruder(); SERIAL_ECHO_MSG(STR_ACTIVE_EXTRUDER, extruder); @@ -861,7 +874,7 @@ void MMU2::filament_runout() { if (cmd == MMU_CMD_NONE && last_cmd == MMU_CMD_C0) { if (present && !mmu2s_triggered) { DEBUG_ECHOLNPGM("MMU <= 'A'"); - tx_str(F("A\n")); + MMU2_SEND("A"); } // Slowly spin the extruder during C0 else { diff --git a/Marlin/src/feature/mmu/mmu2.h b/Marlin/src/feature/mmu/mmu2.h index 7d3d9ec4df..18d6d38a35 100644 --- a/Marlin/src/feature/mmu/mmu2.h +++ b/Marlin/src/feature/mmu/mmu2.h @@ -86,6 +86,7 @@ private: #endif #if ENABLED(MMU_EXTRUDER_SENSOR) + #define MMU_LOAD_FEEDRATE 19.02f // (mm/s) static void mmu_continue_loading(); #endif diff --git a/Marlin/src/gcode/calibrate/M665.cpp b/Marlin/src/gcode/calibrate/M665.cpp index 7dc657a61b..a8e02831e2 100644 --- a/Marlin/src/gcode/calibrate/M665.cpp +++ b/Marlin/src/gcode/calibrate/M665.cpp @@ -167,8 +167,6 @@ if (parser.seenval('T')) draw_area_max.y = parser.value_linear_units(); if (parser.seenval('B')) draw_area_min.y = parser.value_linear_units(); if (parser.seenval('H')) polargraph_max_belt_len = parser.value_linear_units(); - draw_area_size.x = draw_area_max.x - draw_area_min.x; - draw_area_size.y = draw_area_max.y - draw_area_min.y; } void GcodeSuite::M665_report(const bool forReplay/*=true*/) { diff --git a/Marlin/src/gcode/config/M43.cpp b/Marlin/src/gcode/config/M43.cpp index 688b94c9bf..cff143d571 100644 --- a/Marlin/src/gcode/config/M43.cpp +++ b/Marlin/src/gcode/config/M43.cpp @@ -313,7 +313,7 @@ void GcodeSuite::M43() { // 'P' Get the range of pins to test or watch uint8_t first_pin = PARSED_PIN_INDEX('P', 0), - last_pin = parser.seenval('P') ? first_pin : TERN(HAS_HIGH_ANALOG_PINS, NUM_DIGITAL_PINS, NUMBER_PINS_TOTAL) - 1; + last_pin = parser.seenval('P') ? first_pin : (NUMBER_PINS_TOTAL) - 1; if (first_pin > last_pin) return; diff --git a/Marlin/src/gcode/feature/advance/M900.cpp b/Marlin/src/gcode/feature/advance/M900.cpp index db09faa883..50d968627b 100644 --- a/Marlin/src/gcode/feature/advance/M900.cpp +++ b/Marlin/src/gcode/feature/advance/M900.cpp @@ -27,8 +27,8 @@ #include "../../gcode.h" #include "../../../module/planner.h" -#if ENABLED(EXTRA_LIN_ADVANCE_K) - float other_extruder_advance_K[EXTRUDERS]; +#if ENABLED(ADVANCE_K_EXTRA) + float other_extruder_advance_K[DISTINCT_E]; uint8_t lin_adv_slot = 0; #endif @@ -36,8 +36,8 @@ * M900: Get or Set Linear Advance K-factor * T Which tool to address * K Set current advance K factor (Slot 0). - * L Set secondary advance K factor (Slot 1). Requires EXTRA_LIN_ADVANCE_K. - * S<0/1> Activate slot 0 or 1. Requires EXTRA_LIN_ADVANCE_K. + * L Set secondary advance K factor (Slot 1). Requires ADVANCE_K_EXTRA. + * S<0/1> Activate slot 0 or 1. Requires ADVANCE_K_EXTRA. */ void GcodeSuite::M900() { @@ -58,12 +58,12 @@ void GcodeSuite::M900() { } #endif - float &kref = planner.extruder_advance_K[tool_index], newK = kref; + float &kref = planner.extruder_advance_K[E_INDEX_N(tool_index)], newK = kref; const float oldK = newK; - #if ENABLED(EXTRA_LIN_ADVANCE_K) + #if ENABLED(ADVANCE_K_EXTRA) - float &lref = other_extruder_advance_K[tool_index]; + float &lref = other_extruder_advance_K[E_INDEX_N(tool_index)]; const bool old_slot = TEST(lin_adv_slot, tool_index), // The tool's current slot (0 or 1) new_slot = parser.boolval('S', old_slot); // The passed slot (default = current) @@ -111,9 +111,9 @@ void GcodeSuite::M900() { if (!parser.seen_any()) { - #if ENABLED(EXTRA_LIN_ADVANCE_K) + #if ENABLED(ADVANCE_K_EXTRA) - #if EXTRUDERS < 2 + #if DISTINCT_E < 2 SERIAL_ECHOLNPGM("Advance S", new_slot, " K", kref, "(S", !new_slot, " K", lref, ")"); #else EXTRUDER_LOOP() { @@ -127,7 +127,7 @@ void GcodeSuite::M900() { #else SERIAL_ECHO_START(); - #if EXTRUDERS < 2 + #if DISTINCT_E < 2 SERIAL_ECHOLNPGM("Advance K=", planner.extruder_advance_K[0]); #else SERIAL_ECHOPGM("Advance K"); @@ -145,7 +145,7 @@ void GcodeSuite::M900() { void GcodeSuite::M900_report(const bool forReplay/*=true*/) { report_heading(forReplay, F(STR_LINEAR_ADVANCE)); - #if EXTRUDERS < 2 + #if DISTINCT_E < 2 report_echo_start(forReplay); SERIAL_ECHOLNPGM(" M900 K", planner.extruder_advance_K[0]); #else diff --git a/Marlin/src/gcode/gcode.cpp b/Marlin/src/gcode/gcode.cpp index 04523a9a01..bcaea50c16 100644 --- a/Marlin/src/gcode/gcode.cpp +++ b/Marlin/src/gcode/gcode.cpp @@ -561,8 +561,8 @@ void GcodeSuite::process_parsed_command(const bool no_ok/*=false*/) { case 48: M48(); break; // M48: Z probe repeatability test #endif - #if ENABLED(LCD_SET_PROGRESS_MANUALLY) - case 73: M73(); break; // M73: Set progress percentage (for display on LCD) + #if ENABLED(SET_PROGRESS_MANUALLY) + case 73: M73(); break; // M73: Set progress percentage #endif case 75: M75(); break; // M75: Start print timer @@ -600,7 +600,9 @@ void GcodeSuite::process_parsed_command(const bool no_ok/*=false*/) { case 108: M108(); break; // M108: Cancel Waiting case 112: M112(); break; // M112: Full Shutdown case 410: M410(); break; // M410: Quickstop - Abort all the planned moves. - TERN_(HOST_PROMPT_SUPPORT, case 876:) // M876: Handle Host prompt responses + #if ENABLED(HOST_PROMPT_SUPPORT) + case 876: M876(); break; // M876: Handle Host prompt responses + #endif #else case 108: case 112: case 410: TERN_(HOST_PROMPT_SUPPORT, case 876:) @@ -793,6 +795,10 @@ void GcodeSuite::process_parsed_command(const bool no_ok/*=false*/) { case 250: M250(); break; // M250: Set LCD contrast #endif + #if HAS_GCODE_M255 + case 255: M255(); break; // M255: Set LCD Sleep/Backlight Timeout (Minutes) + #endif + #if HAS_LCD_BRIGHTNESS case 256: M256(); break; // M256: Set LCD brightness #endif diff --git a/Marlin/src/gcode/gcode.h b/Marlin/src/gcode/gcode.h index c698a13e99..7cad6d312c 100644 --- a/Marlin/src/gcode/gcode.h +++ b/Marlin/src/gcode/gcode.h @@ -114,7 +114,7 @@ * M43 - Display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins (Requires PINS_DEBUGGING) * M48 - Measure Z Probe repeatability: M48 P X Y V E L S. (Requires Z_MIN_PROBE_REPEATABILITY_TEST) * - * M73 - Set the progress percentage. (Requires LCD_SET_PROGRESS_MANUALLY) + * M73 - Set the progress percentage. (Requires SET_PROGRESS_MANUALLY) * M75 - Start the print job timer. * M76 - Pause the print job timer. * M77 - Stop the print job timer. @@ -677,7 +677,7 @@ private: static void M48(); #endif - #if ENABLED(LCD_SET_PROGRESS_MANUALLY) + #if ENABLED(SET_PROGRESS_MANUALLY) static void M73(); #endif diff --git a/Marlin/src/gcode/host/M115.cpp b/Marlin/src/gcode/host/M115.cpp index d4fca35b42..f2cb4ca2d0 100644 --- a/Marlin/src/gcode/host/M115.cpp +++ b/Marlin/src/gcode/host/M115.cpp @@ -32,6 +32,10 @@ #include "../../feature/caselight.h" #endif +#if ENABLED(HAS_STM32_UID) && !defined(MACHINE_UUID) + #include "../../libs/hex_print.h" +#endif + //#define MINIMAL_CAP_LINES // Don't even mention the disabled capabilities #if ENABLED(EXTENDED_CAPABILITIES_REPORT) @@ -59,20 +63,37 @@ * the capability is not present. */ void GcodeSuite::M115() { - SERIAL_ECHOLNPGM( - "FIRMWARE_NAME:Marlin " DETAILED_BUILD_VERSION " (" __DATE__ " " __TIME__ ") " - "SOURCE_CODE_URL:" SOURCE_CODE_URL " " - "PROTOCOL_VERSION:" PROTOCOL_VERSION " " - "MACHINE_TYPE:" MACHINE_NAME " " - "EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) " " + SERIAL_ECHOPGM("FIRMWARE_NAME:Marlin" + " " DETAILED_BUILD_VERSION " (" __DATE__ " " __TIME__ ")" + " SOURCE_CODE_URL:" SOURCE_CODE_URL + " PROTOCOL_VERSION:" PROTOCOL_VERSION + " MACHINE_TYPE:" MACHINE_NAME + " EXTRUDER_COUNT:" STRINGIFY(EXTRUDERS) #if NUM_AXES != XYZ - "AXIS_COUNT:" STRINGIFY(NUM_AXES) " " + " AXIS_COUNT:" STRINGIFY(NUM_AXES) #endif #ifdef MACHINE_UUID - "UUID:" MACHINE_UUID + " UUID:" MACHINE_UUID #endif ); + // STM32UID:111122223333 + #if ENABLED(HAS_STM32_UID) && !defined(MACHINE_UUID) + // STM32 based devices output the CPU device serial number + // Used by LumenPnP / OpenPNP to keep track of unique hardware/configurations + // https://github.com/opulo-inc/lumenpnp + // Although this code should work on all STM32 based boards + SERIAL_ECHOPGM(" UUID:"); + uint32_t *uid_address = (uint32_t*)UID_BASE; + LOOP_L_N(i, 3) { + const uint32_t UID = uint32_t(READ_REG(*(uid_address))); + uid_address += 4U; + for (int B = 24; B >= 0; B -= 8) print_hex_byte(UID >> B); + } + #endif + + SERIAL_EOL(); + #if ENABLED(EXTENDED_CAPABILITIES_REPORT) // The port that sent M115 @@ -121,7 +142,7 @@ void GcodeSuite::M115() { cap_line(F("LEVELING_DATA"), ENABLED(HAS_LEVELING)); // BUILD_PERCENT (M73) - cap_line(F("BUILD_PERCENT"), ENABLED(LCD_SET_PROGRESS_MANUALLY)); + cap_line(F("BUILD_PERCENT"), ENABLED(SET_PROGRESS_PERCENT)); // SOFTWARE_POWER (M80, M81) cap_line(F("SOFTWARE_POWER"), ENABLED(PSU_CONTROL)); diff --git a/Marlin/src/gcode/lcd/M0_M1.cpp b/Marlin/src/gcode/lcd/M0_M1.cpp index af03fcb0b1..35afea0f6e 100644 --- a/Marlin/src/gcode/lcd/M0_M1.cpp +++ b/Marlin/src/gcode/lcd/M0_M1.cpp @@ -85,7 +85,12 @@ void GcodeSuite::M0_M1() { #endif - TERN_(HOST_PROMPT_SUPPORT, hostui.prompt_do(PROMPT_USER_CONTINUE, parser.codenum ? F("M1 Stop") : F("M0 Stop"), FPSTR(CONTINUE_STR))); + #if ENABLED(HOST_PROMPT_SUPPORT) + if (parser.string_arg) + hostui.prompt_do(PROMPT_USER_CONTINUE, parser.string_arg, FPSTR(CONTINUE_STR)); + else + hostui.prompt_do(PROMPT_USER_CONTINUE, parser.codenum ? F("M1 Stop") : F("M0 Stop"), FPSTR(CONTINUE_STR)); + #endif TERN_(HAS_RESUME_CONTINUE, wait_for_user_response(ms)); diff --git a/Marlin/src/gcode/lcd/M73.cpp b/Marlin/src/gcode/lcd/M73.cpp index a86eee4d99..77d93019ac 100644 --- a/Marlin/src/gcode/lcd/M73.cpp +++ b/Marlin/src/gcode/lcd/M73.cpp @@ -22,21 +22,35 @@ #include "../../inc/MarlinConfig.h" -#if ENABLED(LCD_SET_PROGRESS_MANUALLY) +#if ENABLED(SET_PROGRESS_MANUALLY) #include "../gcode.h" #include "../../lcd/marlinui.h" #include "../../sd/cardreader.h" +#include "../../libs/numtostr.h" #if ENABLED(DWIN_LCD_PROUI) #include "../../lcd/e3v2/proui/dwin.h" #endif +#if ENABLED(M73_REPORT) + #define M73_REPORT_PRUSA +#endif + /** * M73: Set percentage complete (for display on LCD) * * Example: - * M73 P25 ; Set progress to 25% + * M73 P25.63 ; Set progress to 25.63% + * M73 R456 ; Set remaining time to 456 minutes + * M73 C12 ; Set next interaction countdown to 12 minutes + * M73 ; Report current values + * + * Use a shorter-than-Průša report format: + * M73 Percent done: ---%; Time left: -----m; Change: -----m; + * + * When PRINT_PROGRESS_SHOW_DECIMALS is enabled - reports percent with 100 / 23.4 / 3.45 format + * */ void GcodeSuite::M73() { @@ -46,17 +60,39 @@ void GcodeSuite::M73() { #else - if (parser.seenval('P')) - ui.set_progress((PROGRESS_SCALE) > 1 - ? parser.value_float() * (PROGRESS_SCALE) - : parser.value_byte() - ); + #if ENABLED(SET_PROGRESS_PERCENT) + if (parser.seenval('P')) + ui.set_progress((PROGRESS_SCALE) > 1 + ? parser.value_float() * (PROGRESS_SCALE) + : parser.value_byte() + ); + #endif - #if ENABLED(USE_M73_REMAINING_TIME) + #if ENABLED(SET_REMAINING_TIME) if (parser.seenval('R')) ui.set_remaining_time(60 * parser.value_ulong()); #endif + #if ENABLED(SET_INTERACTION_TIME) + if (parser.seenval('C')) ui.set_interaction_time(60 * parser.value_ulong()); + #endif + + #endif + + #if ENABLED(M73_REPORT) + { + SERIAL_ECHO_MSG( + TERN(M73_REPORT_PRUSA, "M73 Percent done: ", "Progress: ") + , TERN(PRINT_PROGRESS_SHOW_DECIMALS, permyriadtostr4(ui.get_progress_permyriad()), ui.get_progress_percent()) + #if ENABLED(SET_REMAINING_TIME) + , TERN(M73_REPORT_PRUSA, "; Print time remaining in mins: ", "%; Time left: "), ui.remaining_time / 60 + #endif + #if ENABLED(SET_INTERACTION_TIME) + , TERN(M73_REPORT_PRUSA, "; Change in mins: ", "m; Change: "), ui.interaction_time / 60 + #endif + , TERN(M73_REPORT_PRUSA, ";", "m") + ); + } #endif } -#endif // LCD_SET_PROGRESS_MANUALLY +#endif // SET_PROGRESS_MANUALLY diff --git a/Marlin/src/gcode/sd/M1001.cpp b/Marlin/src/gcode/sd/M1001.cpp index 197177882c..f404358862 100644 --- a/Marlin/src/gcode/sd/M1001.cpp +++ b/Marlin/src/gcode/sd/M1001.cpp @@ -34,7 +34,7 @@ #include "../queue.h" #endif -#if EITHER(LCD_SET_PROGRESS_MANUALLY, SD_REPRINT_LAST_SELECTED_FILE) +#if EITHER(SET_PROGRESS_MANUALLY, SD_REPRINT_LAST_SELECTED_FILE) #include "../../lcd/marlinui.h" #endif @@ -84,7 +84,7 @@ void GcodeSuite::M1001() { process_subcommands_now(F("M77")); // Set the progress bar "done" state - TERN_(LCD_SET_PROGRESS_MANUALLY, ui.set_progress_done()); + TERN_(SET_PROGRESS_PERCENT, ui.set_progress_done()); // Announce SD file completion { diff --git a/Marlin/src/gcode/sd/M23.cpp b/Marlin/src/gcode/sd/M23.cpp index 51bc824130..8722e9b6de 100644 --- a/Marlin/src/gcode/sd/M23.cpp +++ b/Marlin/src/gcode/sd/M23.cpp @@ -38,7 +38,7 @@ void GcodeSuite::M23() { for (char *fn = parser.string_arg; *fn; ++fn) if (*fn == ' ') *fn = '\0'; card.openFileRead(parser.string_arg); - TERN_(LCD_SET_PROGRESS_MANUALLY, ui.set_progress(0)); + TERN_(SET_PROGRESS_PERCENT, ui.set_progress(0)); } #endif // SDSUPPORT diff --git a/Marlin/src/inc/Conditionals_LCD.h b/Marlin/src/inc/Conditionals_LCD.h index 5f539b794e..969a2ab851 100644 --- a/Marlin/src/inc/Conditionals_LCD.h +++ b/Marlin/src/inc/Conditionals_LCD.h @@ -529,10 +529,6 @@ #define HAS_MANUAL_MOVE_MENU 1 #endif -#if ANY(HAS_MARLINUI_U8GLIB, EXTENSIBLE_UI, HAS_MARLINUI_HD44780, IS_TFTGLCD_PANEL, IS_DWIN_MARLINUI, DWIN_CREALITY_LCD_JYERSUI) - #define CAN_SHOW_REMAINING_TIME 1 -#endif - #if HAS_MARLINUI_U8GLIB #ifndef LCD_PIXEL_WIDTH #define LCD_PIXEL_WIDTH 128 @@ -994,7 +990,7 @@ * with shared motion and temperature settings. * * DISTINCT_E is the number of distinguished extruders. By default this - * well be 1 which indicates all extruders share the same settings. + * will be 1 which indicates all extruders share the same settings. * * E_INDEX_N(E) should be used to get the E index of any item that might be * distinguished. @@ -1484,7 +1480,7 @@ #endif #elif ENABLED(TFT_GENERIC) #define TFT_DEFAULT_ORIENTATION (TFT_EXCHANGE_XY | TFT_INVERT_X | TFT_INVERT_Y) - #if NONE(TFT_RES_320x240, TFT_RES_480x272, TFT_RES_480x320) + #if NONE(TFT_RES_320x240, TFT_RES_480x272, TFT_RES_480x320, TFT_RES_1024x600) #define TFT_RES_320x240 #endif #if NONE(TFT_INTERFACE_FSMC, TFT_INTERFACE_SPI) @@ -1562,6 +1558,8 @@ #elif TFT_HEIGHT == 600 #if ENABLED(TFT_INTERFACE_LTDC) #define TFT_1024x600_LTDC + #else + #define TFT_1024x600_SIM // "Simulation" - for testing purposes only #endif #endif #endif @@ -1572,7 +1570,7 @@ #define HAS_UI_480x320 1 #elif EITHER(TFT_480x272, TFT_480x272_SPI) #define HAS_UI_480x272 1 -#elif defined(TFT_1024x600_LTDC) +#elif EITHER(TFT_1024x600_LTDC, TFT_1024x600_SIM) #define HAS_UI_1024x600 1 #endif #if ANY(HAS_UI_320x240, HAS_UI_480x320, HAS_UI_480x272) diff --git a/Marlin/src/inc/Conditionals_adv.h b/Marlin/src/inc/Conditionals_adv.h index c7f36ce6ec..0dd5c30d09 100644 --- a/Marlin/src/inc/Conditionals_adv.h +++ b/Marlin/src/inc/Conditionals_adv.h @@ -162,9 +162,10 @@ #define HID_E6 6 #define HID_E7 7 -#define _SENSOR_IS(I,N) || (TEMP_SENSOR_##N == I) +#define _SENSOR_IS(I,N) || (TEMP_SENSOR(N) == I) #define _E_SENSOR_IS(I,N) _SENSOR_IS(N,I) -#define ANY_THERMISTOR_IS(N) (0 REPEAT2(HOTENDS, _E_SENSOR_IS, N) \ +#define ANY_E_SENSOR_IS(N) (0 REPEAT2(HOTENDS, _E_SENSOR_IS, N)) +#define ANY_THERMISTOR_IS(N) ( ANY_E_SENSOR_IS(N) \ _SENSOR_IS(N,BED) _SENSOR_IS(N,PROBE) _SENSOR_IS(N,CHAMBER) \ _SENSOR_IS(N,COOLER) _SENSOR_IS(N,BOARD) _SENSOR_IS(N,REDUNDANT) ) @@ -599,10 +600,16 @@ #undef MENU_ADDAUTOSTART #endif -#if EITHER(SDSUPPORT, LCD_SET_PROGRESS_MANUALLY) +#if EITHER(SDSUPPORT, SET_PROGRESS_MANUALLY) #define HAS_PRINT_PROGRESS 1 #endif +#if DISABLED(SET_PROGRESS_MANUALLY) + #undef SET_REMAINING_TIME + #undef SET_INTERACTION_TIME + #undef M73_REPORT +#endif + #if ANY(HAS_MARLINUI_MENU, ULTIPANEL_FEEDMULTIPLY, SOFT_RESET_ON_KILL) #define HAS_ENCODER_ACTION 1 #endif diff --git a/Marlin/src/inc/Conditionals_post.h b/Marlin/src/inc/Conditionals_post.h index c8e933cc80..72803c94b0 100644 --- a/Marlin/src/inc/Conditionals_post.h +++ b/Marlin/src/inc/Conditionals_post.h @@ -155,7 +155,7 @@ #define W_BED_SIZE W_MAX_LENGTH #endif -// Require 0,0 bed center for Delta and SCARA +// Require 0,0 bed center for Delta, SCARA, and Polargraph #if IS_KINEMATIC #define BED_CENTER_AT_0_0 #endif @@ -2656,7 +2656,7 @@ // // ADC Temp Sensors (Thermistor or Thermocouple with amplifier ADC interface) // -#define HAS_ADC_TEST(P) (PIN_EXISTS(TEMP_##P) && TEMP_SENSOR_##P != 0 && !TEMP_SENSOR_IS_MAX_TC(P) && !TEMP_SENSOR_##P##_IS_DUMMY) +#define HAS_ADC_TEST(P) (TEMP_SENSOR(P) && PIN_EXISTS(TEMP_##P) && !TEMP_SENSOR_IS_MAX_TC(P) && !TEMP_SENSOR_##P##_IS_DUMMY) #if HOTENDS > 0 && HAS_ADC_TEST(0) #define HAS_TEMP_ADC_0 1 #endif diff --git a/Marlin/src/inc/SanityCheck.h b/Marlin/src/inc/SanityCheck.h index 16c25c2601..61de2e586e 100644 --- a/Marlin/src/inc/SanityCheck.h +++ b/Marlin/src/inc/SanityCheck.h @@ -587,7 +587,7 @@ #elif defined(MKS_LCD12864) #error "MKS_LCD12864 is now MKS_LCD12864A or MKS_LCD12864B." #elif defined(DOGM_SD_PERCENT) - #error "DOGM_SD_PERCENT is now SHOW_SD_PERCENT." + #error "DOGM_SD_PERCENT is now SHOW_PROGRESS_PERCENT." #elif defined(NEOPIXEL_BKGD_LED_INDEX) #error "NEOPIXEL_BKGD_LED_INDEX is now NEOPIXEL_BKGD_INDEX_FIRST." #elif defined(TEMP_SENSOR_1_AS_REDUNDANT) @@ -646,6 +646,14 @@ #error "TOUCH_IDLE_SLEEP (seconds) is now TOUCH_IDLE_SLEEP_MINS (minutes)." #elif defined(LCD_BACKLIGHT_TIMEOUT) #error "LCD_BACKLIGHT_TIMEOUT (seconds) is now LCD_BACKLIGHT_TIMEOUT_MINS (minutes)." +#elif defined(LCD_SET_PROGRESS_MANUALLY) + #error "LCD_SET_PROGRESS_MANUALLY is now SET_PROGRESS_MANUALLY." +#elif defined(USE_M73_REMAINING_TIME) + #error "USE_M73_REMAINING_TIME is now SET_REMAINING_TIME." +#elif defined(SHOW_SD_PERCENT) + #error "SHOW_SD_PERCENT is now SHOW_PROGRESS_PERCENT." +#elif defined(EXTRA_LIN_ADVANCE_K) + #error "EXTRA_LIN_ADVANCE_K is now ADVANCE_K_EXTRA." #endif // L64xx stepper drivers have been removed @@ -821,7 +829,7 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS /** * Granular software endstops (Marlin >= 1.1.7) */ -#if ENABLED(MIN_SOFTWARE_ENDSTOPS) && DISABLED(MIN_SOFTWARE_ENDSTOP_Z) +#if ENABLED(MIN_SOFTWARE_ENDSTOPS) && NONE(MIN_SOFTWARE_ENDSTOP_Z, POLARGRAPH) #if IS_KINEMATIC #error "MIN_SOFTWARE_ENDSTOPS on DELTA/SCARA also requires MIN_SOFTWARE_ENDSTOP_Z." #elif NONE(MIN_SOFTWARE_ENDSTOP_X, MIN_SOFTWARE_ENDSTOP_Y) @@ -829,7 +837,7 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS #endif #endif -#if ENABLED(MAX_SOFTWARE_ENDSTOPS) && DISABLED(MAX_SOFTWARE_ENDSTOP_Z) +#if ENABLED(MAX_SOFTWARE_ENDSTOPS) && NONE(MAX_SOFTWARE_ENDSTOP_Z, POLARGRAPH) #if IS_KINEMATIC #error "MAX_SOFTWARE_ENDSTOPS on DELTA/SCARA also requires MAX_SOFTWARE_ENDSTOP_Z." #elif NONE(MAX_SOFTWARE_ENDSTOP_X, MAX_SOFTWARE_ENDSTOP_Y) @@ -894,8 +902,8 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS * Progress Bar */ #if ENABLED(LCD_PROGRESS_BAR) - #if NONE(SDSUPPORT, LCD_SET_PROGRESS_MANUALLY) - #error "LCD_PROGRESS_BAR requires SDSUPPORT or LCD_SET_PROGRESS_MANUALLY." + #if NONE(SDSUPPORT, SET_PROGRESS_MANUALLY) + #error "LCD_PROGRESS_BAR requires SDSUPPORT or SET_PROGRESS_MANUALLY." #elif NONE(HAS_MARLINUI_HD44780, IS_TFTGLCD_PANEL) #error "LCD_PROGRESS_BAR only applies to HD44780 character LCD and TFTGLCD_PANEL_(SPI|I2C)." #elif HAS_MARLINUI_U8GLIB || IS_DWIN_MARLINUI @@ -905,12 +913,14 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS #elif PROGRESS_MSG_EXPIRE < 0 #error "PROGRESS_MSG_EXPIRE must be greater than or equal to 0." #endif -#elif ENABLED(LCD_SET_PROGRESS_MANUALLY) && NONE(HAS_MARLINUI_U8GLIB, HAS_GRAPHICAL_TFT, HAS_MARLINUI_HD44780, EXTENSIBLE_UI, HAS_DWIN_E3V2, IS_DWIN_MARLINUI) - #error "LCD_SET_PROGRESS_MANUALLY requires LCD_PROGRESS_BAR, Character LCD, Graphical LCD, TFT, DWIN_CREALITY_LCD, DWIN_LCD_PROUI, DWIN_CREALITY_LCD_JYERSUI, DWIN_MARLINUI_*, OR EXTENSIBLE_UI." #endif -#if ENABLED(USE_M73_REMAINING_TIME) && DISABLED(LCD_SET_PROGRESS_MANUALLY) - #error "USE_M73_REMAINING_TIME requires LCD_SET_PROGRESS_MANUALLY" +#if ENABLED(SET_PROGRESS_MANUALLY) && NONE(SET_PROGRESS_PERCENT, SET_REMAINING_TIME, SET_INTERACTION_TIME) + #error "SET_PROGRESS_MANUALLY requires at least one of SET_PROGRESS_PERCENT, SET_REMAINING_TIME, SET_INTERACTION_TIME to be enabled." +#endif + +#if HAS_LCDPRINT && LCD_HEIGHT < 4 && ANY(SHOW_PROGRESS_PERCENT, SHOW_ELAPSED_TIME, SHOW_REMAINING_TIME, SHOW_INTERACTION_TIME) + #error "Displays with fewer than 4 rows of text can't show progress values." #endif #if !HAS_MARLINUI_MENU && ENABLED(SD_REPRINT_LAST_SELECTED_FILE) @@ -1387,10 +1397,15 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS * Linear Advance 1.5 - Check K value range */ #if ENABLED(LIN_ADVANCE) - static_assert( - WITHIN(LIN_ADVANCE_K, 0, 10), - "LIN_ADVANCE_K must be a value from 0 to 10 (Changed in LIN_ADVANCE v1.5, Marlin 1.1.9)." - ); + #if DISTINCT_E > 1 + constexpr float lak[] = ADVANCE_K; + static_assert(COUNT(lak) < DISTINCT_E, "The ADVANCE_K array has too many elements (i.e., more than " STRINGIFY(DISTINCT_E) ")."); + #define _LIN_ASSERT(N) static_assert(N >= COUNT(lak) || WITHIN(lak[N], 0, 10), "ADVANCE_K values must be from 0 to 10 (Changed in LIN_ADVANCE v1.5, Marlin 1.1.9)."); + REPEAT(DISTINCT_E, _LIN_ASSERT) + #undef _LIN_ASSERT + #else + static_assert(WITHIN(ADVANCE_K, 0, 10), "ADVANCE_K must be from 0 to 10 (Changed in LIN_ADVANCE v1.5, Marlin 1.1.9)."); + #endif #if ENABLED(S_CURVE_ACCELERATION) && DISABLED(EXPERIMENTAL_SCURVE) #error "LIN_ADVANCE and S_CURVE_ACCELERATION may not play well together! Enable EXPERIMENTAL_SCURVE to continue." #elif ENABLED(DIRECT_STEPPING) @@ -2331,6 +2346,37 @@ static_assert(Y_MAX_LENGTH >= Y_BED_SIZE, "Movement bounds (Y_MIN_POS, Y_MAX_POS #error "TEMP_SENSOR_REDUNDANT 1000 requires REDUNDANT_PULLUP_RESISTOR_OHMS, REDUNDANT_RESISTANCE_25C_OHMS and REDUNDANT_BETA in Configuration_adv.h." #endif +/** + * Required thermistor 66 (Dyze Design / Trianglelab T-D500) settings + * https://docs.dyzedesign.com/hotends.html#_500-%C2%B0c-thermistor + */ +#if ANY_E_SENSOR_IS(66) + #define _BAD_MINTEMP(N) (TEMP_SENSOR(N) == 66 && HEATER_##N##_MINTEMP <= 20) + #if _BAD_MINTEMP(0) + #error "Thermistor 66 requires HEATER_0_MINTEMP > 20." + #elif _BAD_MINTEMP(1) + #error "Thermistor 66 requires HEATER_1_MINTEMP > 20." + #elif _BAD_MINTEMP(2) + #error "Thermistor 66 requires HEATER_2_MINTEMP > 20." + #elif _BAD_MINTEMP(3) + #error "Thermistor 66 requires HEATER_3_MINTEMP > 20." + #elif _BAD_MINTEMP(4) + #error "Thermistor 66 requires HEATER_4_MINTEMP > 20." + #elif _BAD_MINTEMP(5) + #error "Thermistor 66 requires HEATER_5_MINTEMP > 20." + #elif _BAD_MINTEMP(6) + #error "Thermistor 66 requires HEATER_6_MINTEMP > 20." + #elif _BAD_MINTEMP(7) + #error "Thermistor 66 requires HEATER_7_MINTEMP > 20." + #endif + #if MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED < 5 + #error "Thermistor 66 requires MAX_CONSECUTIVE_LOW_TEMPERATURE_ERROR_ALLOWED ≥ 5." + #elif MILLISECONDS_PREHEAT_TIME < 30000 + #error "Thermistor 66 requires MILLISECONDS_PREHEAT_TIME ≥ 30000." + #endif + #undef _BAD_MINTEMP +#endif + /** * Required MAX31865 settings */ @@ -4066,10 +4112,6 @@ static_assert(_PLUS_TEST(4), "HOMING_FEEDRATE_MM_M values must be positive."); #error "COOLANT_FLOOD requires COOLANT_FLOOD_PIN to be defined." #endif -#if NONE(HAS_MARLINUI_U8GLIB, EXTENSIBLE_UI, IS_DWIN_MARLINUI) && ENABLED(PRINT_PROGRESS_SHOW_DECIMALS) - #error "PRINT_PROGRESS_SHOW_DECIMALS currently requires a Graphical LCD." -#endif - #if HAS_ADC_BUTTONS && defined(ADC_BUTTON_DEBOUNCE_DELAY) && ADC_BUTTON_DEBOUNCE_DELAY < 16 #error "ADC_BUTTON_DEBOUNCE_DELAY must be greater than 16." #endif diff --git a/Marlin/src/inc/Version.h b/Marlin/src/inc/Version.h index c7a0f79553..6d3dba75b4 100644 --- a/Marlin/src/inc/Version.h +++ b/Marlin/src/inc/Version.h @@ -42,7 +42,7 @@ * version was tagged. */ #ifndef STRING_DISTRIBUTION_DATE - #define STRING_DISTRIBUTION_DATE "2022-09-14" + #define STRING_DISTRIBUTION_DATE "2022-10-16" #endif /** diff --git a/Marlin/src/inc/Warnings.cpp b/Marlin/src/inc/Warnings.cpp index 65174593fb..1228db336c 100644 --- a/Marlin/src/inc/Warnings.cpp +++ b/Marlin/src/inc/Warnings.cpp @@ -711,8 +711,8 @@ #warning "Don't forget to update your TFT settings in Configuration.h." #endif -#if ENABLED(EMIT_CREALITY_422_WARNING) - #warning "Creality 4.2.2 boards come with a variety of stepper drivers. Check the board label and set the correct *_DRIVER_TYPE! (C=HR4988, E=A4988, A=TMC2208, B=TMC2209, H=TMC2225). (Define EMIT_CREALITY_422_WARNING false to suppress this warning.)" +#if ENABLED(EMIT_CREALITY_422_WARNING) && DISABLED(NO_CREALITY_422_DRIVER_WARNING) + #warning "Creality 4.2.2 boards come with a variety of stepper drivers. Check the board label and set the correct *_DRIVER_TYPE! (C=HR4988, E=A4988, A=TMC2208, B=TMC2209, H=TMC2225). (Define NO_CREALITY_422_DRIVER_WARNING to suppress this warning.)" #endif #if PRINTCOUNTER_SYNC diff --git a/Marlin/src/lcd/HD44780/marlinui_HD44780.cpp b/Marlin/src/lcd/HD44780/marlinui_HD44780.cpp index b8dc8db817..ba222897fc 100644 --- a/Marlin/src/lcd/HD44780/marlinui_HD44780.cpp +++ b/Marlin/src/lcd/HD44780/marlinui_HD44780.cpp @@ -612,20 +612,6 @@ FORCE_INLINE void _draw_bed_status(const bool blink) { _draw_heater_status(H_BED, TERN0(HAS_LEVELING, blink && planner.leveling_active) ? '_' : LCD_STR_BEDTEMP[0], blink); } -#if HAS_PRINT_PROGRESS - - FORCE_INLINE void _draw_print_progress() { - const uint8_t progress = ui.get_progress_percent(); - lcd_put_u8str(F(TERN(SDSUPPORT, "SD", "P:"))); - if (progress) - lcd_put_u8str(ui8tostr3rj(progress)); - else - lcd_put_u8str(F("---")); - lcd_put_lchar('%'); - } - -#endif - #if ENABLED(LCD_PROGRESS_BAR) void MarlinUI::draw_progress_bar(const uint8_t percent) { @@ -733,6 +719,56 @@ void MarlinUI::draw_status_message(const bool blink) { #endif } +#if HAS_PRINT_PROGRESS + #define TPOFFSET (LCD_WIDTH - 1) + static uint8_t timepos = TPOFFSET - 6; + static char buffer[14]; + static lcd_uint_t pc, pr; + + #if ENABLED(SHOW_PROGRESS_PERCENT) + void MarlinUI::drawPercent() { + const uint8_t progress = ui.get_progress_percent(); + if (progress) { + lcd_moveto(pc, pr); + lcd_put_u8str(F(TERN(IS_SD_PRINTING, "SD", "P:"))); + lcd_put_u8str(TERN(PRINT_PROGRESS_SHOW_DECIMALS, permyriadtostr4(ui.get_progress_permyriad()), ui8tostr3rj(progress))); + lcd_put_lchar('%'); + } + } + #endif + #if ENABLED(SHOW_REMAINING_TIME) + void MarlinUI::drawRemain() { + const duration_t remaint = ui.get_remaining_time(); + if (printJobOngoing()) { + timepos = TPOFFSET - remaint.toDigital(buffer); + lcd_put_lchar(TERN(LCD_INFO_SCREEN_STYLE, 11, timepos), 2, 'R'); + lcd_put_u8str(buffer); + } + } + #endif + #if ENABLED(SHOW_INTERACTION_TIME) + void MarlinUI::drawInter() { + const duration_t interactt = ui.interaction_time; + if (printingIsActive() && interactt.value) { + timepos = TPOFFSET - interactt.toDigital(buffer); + lcd_put_lchar(TERN(LCD_INFO_SCREEN_STYLE, 11, timepos), 2, 'C'); + lcd_put_u8str(buffer); + } + } + #endif + #if ENABLED(SHOW_ELAPSED_TIME) + void MarlinUI::drawElapsed() { + const duration_t elapsedt = print_job_timer.duration(); + if (printJobOngoing()) { + timepos = TPOFFSET - elapsedt.toDigital(buffer); + lcd_put_lchar(TERN(LCD_INFO_SCREEN_STYLE, 11, timepos), 2, 'E'); + //lcd_put_lchar(timepos, 2, LCD_STR_CLOCK[0]); + lcd_put_u8str(buffer); + } + } + #endif +#endif // HAS_PRINT_PROGRESS + /** * LCD_INFO_SCREEN_STYLE 0 : Classic Status Screen * @@ -765,35 +801,6 @@ void MarlinUI::draw_status_message(const bool blink) { * |01234567890123456789| */ -inline uint8_t draw_elapsed_or_remaining_time(uint8_t timepos, const bool blink) { - char buffer[14]; - - #if ENABLED(SHOW_REMAINING_TIME) - const bool show_remain = TERN1(ROTATE_PROGRESS_DISPLAY, blink) && printingIsActive(); - if (show_remain) { - #if ENABLED(USE_M73_REMAINING_TIME) - duration_t remaining = ui.get_remaining_time(); - #else - uint8_t progress = ui.get_progress_percent(); - uint32_t elapsed = print_job_timer.duration(); - duration_t remaining = (progress > 0) ? ((elapsed * 25600 / progress) >> 8) - elapsed : 0; - #endif - timepos -= remaining.toDigital(buffer); - lcd_put_lchar(timepos, 2, 'R'); - } - #else - constexpr bool show_remain = false; - #endif - - if (!show_remain) { - duration_t elapsed = print_job_timer.duration(); - timepos -= elapsed.toDigital(buffer); - lcd_put_lchar(timepos, 2, LCD_STR_CLOCK[0]); - } - lcd_put_u8str(buffer); - return timepos; -} - void MarlinUI::draw_status_screen() { const bool blink = get_blink(); @@ -856,8 +863,8 @@ void MarlinUI::draw_status_screen() { #if LCD_WIDTH < 20 #if HAS_PRINT_PROGRESS - lcd_moveto(0, 2); - _draw_print_progress(); + pc = 0, pr = 2; + rotate_progress(); #endif #else // LCD_WIDTH >= 20 @@ -940,12 +947,11 @@ void MarlinUI::draw_status_screen() { lcd_put_u8str(i16tostr3rj(feedrate_percentage)); lcd_put_lchar('%'); - const uint8_t timepos = draw_elapsed_or_remaining_time(LCD_WIDTH - 1, blink); - #if LCD_WIDTH >= 20 - lcd_moveto(timepos - 7, 2); + #if HAS_PRINT_PROGRESS - _draw_print_progress(); + pc = timepos - 7, pr = 2; + rotate_progress(); #else char c; uint16_t per; @@ -1016,7 +1022,7 @@ void MarlinUI::draw_status_screen() { // ========== Line 3 ========== // - // SD Percent, Hotend 2, or Bed + // Progress percent, Hotend 2, or Bed // lcd_moveto(0, 2); #if HOTENDS > 2 @@ -1025,24 +1031,17 @@ void MarlinUI::draw_status_screen() { _draw_bed_status(blink); #elif HAS_PRINT_PROGRESS #define DREW_PRINT_PROGRESS 1 - _draw_print_progress(); + pc = 0, pr = 2; + rotate_progress(); #endif // - // Elapsed Time or SD Percent + // All progress strings // - lcd_moveto(LCD_WIDTH - 9, 2); - #if HAS_PRINT_PROGRESS && !DREW_PRINT_PROGRESS - - _draw_print_progress(); - - #else - - (void)draw_elapsed_or_remaining_time(LCD_WIDTH - 4, blink); - + pc = LCD_WIDTH - 9, pr = 2; + rotate_progress(); #endif - #endif // LCD_INFO_SCREEN_STYLE 1 // ========= Last Line ======== diff --git a/Marlin/src/lcd/TFTGLCD/marlinui_TFTGLCD.cpp b/Marlin/src/lcd/TFTGLCD/marlinui_TFTGLCD.cpp index f3d98ec555..029a04bf97 100644 --- a/Marlin/src/lcd/TFTGLCD/marlinui_TFTGLCD.cpp +++ b/Marlin/src/lcd/TFTGLCD/marlinui_TFTGLCD.cpp @@ -606,7 +606,7 @@ FORCE_INLINE void _draw_axis_value(const AxisEnum axis, const char *value, const const uint8_t progress = ui._get_progress(); #if ENABLED(SDSUPPORT) lcd_put_u8str(F("SD")); - #elif ENABLED(LCD_SET_PROGRESS_MANUALLY) + #elif ENABLED(SET_PROGRESS_PERCENT) lcd_put_u8str(F("P:")); #endif if (progress) diff --git a/Marlin/src/lcd/dogm/status_screen_DOGM.cpp b/Marlin/src/lcd/dogm/status_screen_DOGM.cpp index 67039d52de..81119c0a10 100644 --- a/Marlin/src/lcd/dogm/status_screen_DOGM.cpp +++ b/Marlin/src/lcd/dogm/status_screen_DOGM.cpp @@ -40,9 +40,7 @@ #include "../../gcode/parser.h" // for units (and volumetric) -#if ENABLED(LCD_SHOW_E_TOTAL) - #include "../../MarlinCore.h" // for printingIsActive() -#endif +#include "../../MarlinCore.h" // for printingIsActive() #if ENABLED(FILAMENT_LCD_DISPLAY) #include "../../feature/filwidth.h" @@ -445,6 +443,55 @@ FORCE_INLINE void _draw_axis_value(const AxisEnum axis, const char *value, const lcd_put_u8str(value); } +// Prepare strings for progress display +#if HAS_PRINT_PROGRESS + #define _PRGR_INFO_X(len) (LCD_PIXEL_WIDTH - (len) * (MENU_FONT_WIDTH)) + #define PCENTERED 1 // center percent value over progress bar, else align to the right + static uint8_t lastProgress = 0xFF; + static u8g_uint_t progress_bar_solid_width = 0; + #if ENABLED(SHOW_PROGRESS_PERCENT) + static char progress_string[5]; + static u8g_uint_t progress_x_pos; + void MarlinUI::drawPercent() { + if (progress_string[0]) { + lcd_put_u8str(progress_x_pos, EXTRAS_BASELINE, progress_string); + lcd_put_lchar('%'); + } + } + #endif + #if ENABLED(SHOW_REMAINING_TIME) + static char remaining_string[10]; + static u8g_uint_t remaining_x_pos = 0; + void MarlinUI::drawRemain() { + if (printJobOngoing()){ + lcd_put_u8str(PROGRESS_BAR_X, EXTRAS_BASELINE, F("R:")); + lcd_put_u8str(remaining_x_pos, EXTRAS_BASELINE, remaining_string); + } + } + #endif + #if ENABLED(SHOW_INTERACTION_TIME) + static char interaction_string[10]; + static u8g_uint_t interaction_x_pos = 0; + void MarlinUI::drawInter() { + if (printingIsActive() && interaction_string[0]) { + lcd_put_u8str(PROGRESS_BAR_X, EXTRAS_BASELINE, F("C:")); + lcd_put_u8str(interaction_x_pos, EXTRAS_BASELINE, interaction_string); + } + } + #endif + #if ENABLED(SHOW_ELAPSED_TIME) + static char elapsed_string[10]; + static u8g_uint_t elapsed_x_pos = 0; + static uint8_t lastElapsed; + void MarlinUI::drawElapsed() { + if (printJobOngoing()) { + lcd_put_u8str(PROGRESS_BAR_X, EXTRAS_BASELINE, F("E:")); + lcd_put_u8str(elapsed_x_pos, EXTRAS_BASELINE, elapsed_string); + } + } + #endif +#endif // HAS_PRINT_PROGRESS + /** * Draw the Status Screen for a 128x64 DOGM (U8glib) display. * @@ -459,30 +506,6 @@ void MarlinUI::draw_status_screen() { static char wstring[5], mstring[4]; #endif - #if HAS_PRINT_PROGRESS - #if DISABLED(SHOW_SD_PERCENT) - #define _SD_INFO_X(len) (PROGRESS_BAR_X + (PROGRESS_BAR_WIDTH) / 2 - (len) * (MENU_FONT_WIDTH) / 2) - #else - #define _SD_INFO_X(len) (LCD_PIXEL_WIDTH - (len) * (MENU_FONT_WIDTH)) - #endif - - #if ENABLED(SHOW_SD_PERCENT) - static char progress_string[5]; - #endif - static uint8_t lastElapsed = 0xFF, lastProgress = 0xFF; - static u8g_uint_t elapsed_x_pos = 0, progress_bar_solid_width = 0; - static char elapsed_string[16]; - #if ENABLED(SHOW_REMAINING_TIME) - static u8g_uint_t estimation_x_pos = 0; - static char estimation_string[10]; - #if BOTH(SHOW_SD_PERCENT, ROTATE_PROGRESS_DISPLAY) - static u8g_uint_t progress_x_pos = 0; - static uint8_t progress_state = 0; - static bool prev_blink = 0; - #endif - #endif - #endif - const bool show_e_total = TERN0(LCD_SHOW_E_TOTAL, printingIsActive()); // At the first page, generate new display values @@ -523,61 +546,59 @@ void MarlinUI::draw_status_screen() { // Progress / elapsed / estimation updates and string formatting to avoid float math on each LCD draw #if HAS_PRINT_PROGRESS const progress_t progress = TERN(HAS_PRINT_PROGRESS_PERMYRIAD, get_progress_permyriad, get_progress_percent)(); - duration_t elapsed = print_job_timer.duration(); - const uint8_t p = progress & 0xFF, ev = elapsed.value & 0xFF; + duration_t elapsedt = print_job_timer.duration(); + const uint8_t p = progress & 0xFF, ev = elapsedt.value & 0xFF; if (p != lastProgress) { lastProgress = p; progress_bar_solid_width = u8g_uint_t((PROGRESS_BAR_WIDTH - 2) * (progress / (PROGRESS_SCALE)) * 0.01f); - #if ENABLED(SHOW_SD_PERCENT) - if (progress == 0) { + #if ENABLED(SHOW_PROGRESS_PERCENT) + if (progress == 0) progress_string[0] = '\0'; - #if ENABLED(SHOW_REMAINING_TIME) - estimation_string[0] = '\0'; - estimation_x_pos = _SD_INFO_X(0); - #endif - } else strcpy(progress_string, TERN(PRINT_PROGRESS_SHOW_DECIMALS, permyriadtostr4(progress), ui8tostr3rj(progress / (PROGRESS_SCALE)))); - - #if BOTH(SHOW_REMAINING_TIME, ROTATE_PROGRESS_DISPLAY) // Tri-state progress display mode - progress_x_pos = _SD_INFO_X(strlen(progress_string) + 1); - #endif + progress_x_pos = TERN(PCENTERED, 77, _PRGR_INFO_X(strlen(progress_string) + 1)); #endif } - constexpr bool can_show_days = DISABLED(SHOW_SD_PERCENT) || ENABLED(ROTATE_PROGRESS_DISPLAY); - if (ev != lastElapsed) { - lastElapsed = ev; - const uint8_t len = elapsed.toDigital(elapsed_string, can_show_days && elapsed.value >= 60*60*24L); - elapsed_x_pos = _SD_INFO_X(len); + #if ENABLED(SHOW_INTERACTION_TIME) + if (!(interaction_time)) { + interaction_string[0] = '\0'; + interaction_x_pos = _PRGR_INFO_X(0); + } + else { + const duration_t interactt = ui.interaction_time; + interactt.toDigital(interaction_string, interactt.value >= 60*60*24L); + interaction_x_pos = _PRGR_INFO_X(strlen(interaction_string)); + } + #endif - #if ENABLED(SHOW_REMAINING_TIME) - if (!(ev & 0x3)) { - uint32_t timeval = (0 - #if BOTH(LCD_SET_PROGRESS_MANUALLY, USE_M73_REMAINING_TIME) - + get_remaining_time() - #endif - ); - if (!timeval && progress > 0) timeval = elapsed.value * (100 * (PROGRESS_SCALE) - progress) / progress; - if (!timeval) { - estimation_string[0] = '\0'; - estimation_x_pos = _SD_INFO_X(0); - } - else { - duration_t estimation = timeval; - const uint8_t len = estimation.toDigital(estimation_string, can_show_days && estimation.value >= 60*60*24L); - estimation_x_pos = _SD_INFO_X(len + !BOTH(SHOW_SD_PERCENT, ROTATE_PROGRESS_DISPLAY)); - } + #if ENABLED(SHOW_ELAPSED_TIME) + if (ev != lastElapsed) { + lastElapsed = ev; + const uint8_t len = elapsedt.toDigital(elapsed_string, elapsedt.value >= 60*60*24L); + elapsed_x_pos = _PRGR_INFO_X(len); + } + #endif + + #if ENABLED(SHOW_REMAINING_TIME) + if (!(ev & 0x3)) { + uint32_t timeval = get_remaining_time(); + if (!timeval) { + remaining_string[0] = '\0'; + remaining_x_pos = _PRGR_INFO_X(0); } - #endif - } + else { + const duration_t remaint = timeval; + const uint8_t len = remaint.toDigital(remaining_string, remaint.value >= 60*60*24L); + remaining_x_pos = _PRGR_INFO_X(len); + } + } + #endif #endif } - const bool blink = get_blink(); - // Status Menu Font set_font(FONT_STATUSMENU); @@ -634,6 +655,8 @@ void MarlinUI::draw_status_screen() { u8g.drawBitmapP(STATUS_CHAMBER_X, chambery, STATUS_CHAMBER_BYTEWIDTH, chamberh, CHAMBER_BITMAP(CHAMBER_ALT())); #endif + const bool blink = ui.get_blink(); + #if DO_DRAW_FAN #if STATUS_FAN_FRAMES > 2 static bool old_blink; @@ -664,8 +687,7 @@ void MarlinUI::draw_status_screen() { if (PAGE_UNDER(6 + 1 + 12 + 1 + 6 + 1)) { // Extruders #if DO_DRAW_HOTENDS - LOOP_L_N(e, MAX_HOTEND_DRAW) - _draw_hotend_status((heater_id_t)e, blink); + LOOP_L_N(e, MAX_HOTEND_DRAW) _draw_hotend_status((heater_id_t)e, blink); #endif // Laser / Spindle @@ -757,74 +779,18 @@ void MarlinUI::draw_status_screen() { #endif // SDSUPPORT #if HAS_PRINT_PROGRESS - // // Progress bar frame - // - if (PAGE_CONTAINS(PROGRESS_BAR_Y, PROGRESS_BAR_Y + 3)) u8g.drawFrame(PROGRESS_BAR_X, PROGRESS_BAR_Y, PROGRESS_BAR_WIDTH, 4); - // // Progress bar solid part - // - if (PAGE_CONTAINS(PROGRESS_BAR_Y + 1, PROGRESS_BAR_Y + 2)) u8g.drawBox(PROGRESS_BAR_X + 1, PROGRESS_BAR_Y + 1, progress_bar_solid_width, 2); - if (PAGE_CONTAINS(EXTRAS_BASELINE - INFO_FONT_ASCENT, EXTRAS_BASELINE - 1)) { - - #if ALL(SHOW_SD_PERCENT, SHOW_REMAINING_TIME, ROTATE_PROGRESS_DISPLAY) - - if (prev_blink != blink) { - prev_blink = blink; - if (++progress_state >= 3) progress_state = 0; - } - - if (progress_state == 0) { - if (progress_string[0]) { - lcd_put_u8str(progress_x_pos, EXTRAS_BASELINE, progress_string); - lcd_put_lchar('%'); - } - } - else if (progress_state == 2 && estimation_string[0]) { - lcd_put_u8str(PROGRESS_BAR_X, EXTRAS_BASELINE, F("R:")); - lcd_put_u8str(estimation_x_pos, EXTRAS_BASELINE, estimation_string); - } - else if (elapsed_string[0]) { - lcd_put_u8str(PROGRESS_BAR_X, EXTRAS_BASELINE, F("E:")); - lcd_put_u8str(elapsed_x_pos, EXTRAS_BASELINE, elapsed_string); - } - - #else // !SHOW_SD_PERCENT || !SHOW_REMAINING_TIME || !ROTATE_PROGRESS_DISPLAY - - // - // SD Percent Complete - // - - #if ENABLED(SHOW_SD_PERCENT) - if (progress_string[0]) { - lcd_put_u8str(55, EXTRAS_BASELINE, progress_string); // Percent complete - lcd_put_lchar('%'); - } - #endif - - // - // Elapsed Time - // - - #if ENABLED(SHOW_REMAINING_TIME) - if (blink && estimation_string[0]) { - lcd_put_lchar(estimation_x_pos, EXTRAS_BASELINE, 'R'); - lcd_put_u8str(estimation_string); - } - else - #endif - lcd_put_u8str(elapsed_x_pos, EXTRAS_BASELINE, elapsed_string); - - #endif // !SHOW_SD_PERCENT || !SHOW_REMAINING_TIME || !ROTATE_PROGRESS_DISPLAY - } - - #endif // HAS_PRINT_PROGRESS + // Progress strings + if (PAGE_CONTAINS(EXTRAS_BASELINE - INFO_FONT_ASCENT, EXTRAS_BASELINE - 1)) + ui.rotate_progress(); + #endif // // XYZ Coordinates diff --git a/Marlin/src/lcd/dogm/status_screen_lite_ST7920.cpp b/Marlin/src/lcd/dogm/status_screen_lite_ST7920.cpp index 492a79a311..9ed0d8a9d6 100644 --- a/Marlin/src/lcd/dogm/status_screen_lite_ST7920.cpp +++ b/Marlin/src/lcd/dogm/status_screen_lite_ST7920.cpp @@ -40,12 +40,38 @@ // Lightweight Status Screen for Graphical Display // +/** One hotend layout + * ------------------ + * |⟱ xxx➜xxx° ✱xxx% + * |＿ xxx➜xxx° Fxxx% + * ||||||||||R•xxx:xx + * | status string + * ------------------ + * + * hotend temp | fan speed + * bed temp | feedrate + * progress bar| progress time + * status string + * + * **************************** + * Two hotends layout + * ------------------ + * |⟱ xxx➜xxx° ✱xxx% + * |⟱ xxx➜xxx°||||||| + * |＿ xxx➜xxx°Rxxx:xx + * | status string + * ------------------ + * + * hotend temp | fan speed + * hotend temp | progress bar + * bed temp | progress time + * status string + */ + #include "../../inc/MarlinConfigPre.h" #if ENABLED(LIGHTWEIGHT_UI) -#include "status_screen_lite_ST7920.h" - #include "../marlinui.h" #include "../fontutils.h" #include "../lcdprint.h" @@ -53,12 +79,13 @@ #include "../../module/motion.h" #include "../../module/printcounter.h" #include "../../module/temperature.h" +#include "../../libs/numtostr.h" #if ENABLED(SDSUPPORT) #include "../../sd/cardreader.h" #endif -#if ENABLED(LCD_SHOW_E_TOTAL) +#if ENABLED(LCD_SHOW_E_TOTAL) || HAS_PRINT_PROGRESS #include "../../MarlinCore.h" // for printingIsActive #endif @@ -72,6 +99,9 @@ #define DDRAM_LINE_3 0x08 #define DDRAM_LINE_4 0x18 +#include "status_screen_lite_ST7920.h" +extern ST7920_Lite_Status_Screen lightUI; + ST7920_Lite_Status_Screen::st7920_state_t ST7920_Lite_Status_Screen::current_bits; void ST7920_Lite_Status_Screen::cmd(const uint8_t cmd) { @@ -442,72 +472,6 @@ void ST7920_Lite_Status_Screen::draw_static_elements() { draw_fan_icon(false); } -/** - * Although this is undocumented, the ST7920 allows the character - * data buffer (DDRAM) to be used in conjunction with the graphics - * bitmap buffer (CGRAM). The contents of the graphics buffer is - * XORed with the data from the character generator. This allows - * us to make the progress bar out of graphical data (the bar) and - * text data (the percentage). - */ -void ST7920_Lite_Status_Screen::draw_progress_bar(const uint8_t value) { - #if HOTENDS == 1 - // If we have only one extruder, draw a long progress bar on the third line - constexpr uint8_t top = 1, // Top in pixels - bottom = 13, // Bottom in pixels - left = 12, // Left edge, in 16-bit words - width = 4; // Width of progress bar, in 16-bit words - #else - constexpr uint8_t top = 16 + 1, - bottom = 16 + 13, - left = 5, - width = 3; - #endif - const uint8_t char_pcnt = 100 / width; // How many percent does each 16-bit word represent? - - // Draw the progress bar as a bitmap in CGRAM - LOOP_S_LE_N(y, top, bottom) { - set_gdram_address(left, y); - begin_data(); - LOOP_L_N(x, width) { - uint16_t gfx_word = 0x0000; - if ((x + 1) * char_pcnt <= value) - gfx_word = 0xFFFF; // Draw completely filled bytes - else if ((x * char_pcnt) < value) - gfx_word = int(0x8000) >> (value % char_pcnt) * 16 / char_pcnt; // Draw partially filled bytes - - // Draw the frame around the progress bar - if (y == top || y == bottom) - gfx_word = 0xFFFF; // Draw top/bottom border - else if (x == width - 1) - gfx_word |= 0x0001; // Draw right border - else if (x == 0) - gfx_word |= 0x8000; // Draw left border - write_word(gfx_word); - } - } - - // Draw the percentage as text in DDRAM - #if HOTENDS == 1 - set_ddram_address(DDRAM_LINE_3 + 4); - begin_data(); - write_byte(' '); - #else - set_ddram_address(DDRAM_LINE_2 + left); - begin_data(); - #endif - - // Draw centered - if (value > 9) { - write_number(value, 4); - write_str(F("% ")); - } - else { - write_number(value, 3); - write_str(F("% ")); - } -} - void ST7920_Lite_Status_Screen::draw_fan_icon(const bool whichIcon) { set_ddram_address(DDRAM_LINE_1 + 5); begin_data(); @@ -592,22 +556,8 @@ void ST7920_Lite_Status_Screen::draw_fan_speed(const uint8_t value) { write_byte('%'); } -void ST7920_Lite_Status_Screen::draw_print_time(const duration_t &elapsed, char suffix) { - #if HOTENDS == 1 - set_ddram_address(DDRAM_LINE_3); - #else - set_ddram_address(DDRAM_LINE_3 + 5); - #endif - char str[7]; - int str_length = elapsed.toDigital(str); - str[str_length++] = suffix; - begin_data(); - write_str(str, str_length); -} - void ST7920_Lite_Status_Screen::draw_feedrate_percentage(const uint16_t percentage) { - // We only have enough room for the feedrate when - // we have one extruder + // We only have enough room for the feedrate when we have one extruder #if HOTENDS == 1 set_ddram_address(DDRAM_LINE_2 + 6); begin_data(); @@ -631,11 +581,9 @@ void ST7920_Lite_Status_Screen::draw_status_message() { write_str(str); while (slen < TEXT_MODE_LCD_WIDTH) { write_byte(' '); ++slen; } } - else { - // String is larger than the available space in screen. + else { // String is larger than the available space in ST7920_Lite_Status_Screen:: - // Get a pointer to the next valid UTF8 character - // and the string remaining length + // Get a pointer to the next valid UTF8 character and the string remaining length uint8_t rlen; const char *stat = ui.status_and_len(rlen); write_str(stat, TEXT_MODE_LCD_WIDTH); @@ -643,12 +591,12 @@ void ST7920_Lite_Status_Screen::draw_status_message() { // If the remaining string doesn't completely fill the screen if (rlen < TEXT_MODE_LCD_WIDTH) { uint8_t chars = TEXT_MODE_LCD_WIDTH - rlen; // Amount of space left in characters - write_byte(' '); // Always at 1+ spaces left, draw a space - if (--chars) { // Draw a second space if there's room + write_byte(' '); // Always at 1+ spaces left, draw a space + if (--chars) { // Draw a second space if there's room write_byte(' '); - if (--chars) { // Draw a third space if there's room + if (--chars) { // Draw a third space if there's room write_byte(' '); - if (--chars) write_str(str, chars); // Print a second copy of the message + if (--chars) write_str(str, chars); // Print a second copy of the message } } } @@ -715,11 +663,155 @@ bool ST7920_Lite_Status_Screen::indicators_changed() { return true; } +// Process progress strings +#if HAS_PRINT_PROGRESS + static char screenstr[8]; + + char * ST7920_Lite_Status_Screen::prepare_time_string(const duration_t &time, char prefix) { + static char str[6]; + memset(&screenstr, 0x20, 8); // fill with spaces to avoid artifacts, not doing right-justification to save cycles + screenstr[0] = prefix; + TERN_(HOTENDS == 1, screenstr[1] = 0x07;) // add bullet • separator when there is space + int str_length = time.toDigital(str); + memcpy(&screenstr[TERN(HOTENDS == 1, 2, 1)], str, str_length); //memcpy because we can't have terminator + return screenstr; + } + + void ST7920_Lite_Status_Screen::draw_progress_string(uint8_t addr, const char *str) { + set_ddram_address(addr); + begin_data(); + write_str(str, TERN(HOTENDS == 1, 8, 6)); + } + + #define PPOS (DDRAM_LINE_3 + TERN(HOTENDS == 1, 4, 5)) // progress string position, in 16-bit words + + #if ENABLED(SHOW_PROGRESS_PERCENT) + void MarlinUI::drawPercent() { lightUI.drawPercent(); } + void ST7920_Lite_Status_Screen::drawPercent() { + #define LSHIFT TERN(HOTENDS == 1, 0, 1) + const uint8_t progress = ui.get_progress_percent(); + memset(&screenstr, 0x20, 8); // fill with spaces to avoid artifacts + if (progress){ + memcpy(&screenstr[2 - LSHIFT], \ + TERN(PRINT_PROGRESS_SHOW_DECIMALS, permyriadtostr4(ui.get_progress_permyriad()), ui8tostr3rj(progress)), \ + TERN(PRINT_PROGRESS_SHOW_DECIMALS, 4, 3)); + screenstr[(TERN(PRINT_PROGRESS_SHOW_DECIMALS, 6, 5) - LSHIFT)] = '%'; + draw_progress_string(PPOS, screenstr); + } + } + #endif + #if ENABLED(SHOW_REMAINING_TIME) + void MarlinUI::drawRemain() { lightUI.drawRemain(); } + void ST7920_Lite_Status_Screen::drawRemain() { + const duration_t remaint = TERN0(SET_REMAINING_TIME, ui.get_remaining_time()); + if (printJobOngoing() && remaint.value) { + draw_progress_string( PPOS, prepare_time_string(remaint, 'R')); + } + } + #endif + #if ENABLED(SHOW_INTERACTION_TIME) + void MarlinUI::drawInter() { lightUI.drawInter(); } + void ST7920_Lite_Status_Screen::drawInter() { + const duration_t interactt = ui.interaction_time; + if (printingIsActive() && interactt.value) { + draw_progress_string( PPOS, prepare_time_string(interactt, 'C')); + } + } + #endif + #if ENABLED(SHOW_ELAPSED_TIME) + void MarlinUI::drawElapsed() { lightUI.drawElapsed(); } + void ST7920_Lite_Status_Screen::drawElapsed() { + if (printJobOngoing()) { + const duration_t elapsedt = print_job_timer.duration(); + draw_progress_string( PPOS, prepare_time_string(elapsedt, 'E')); + } + } + #endif + + /** + * Although this is undocumented, the ST7920 allows the character + * data buffer (DDRAM) to be used in conjunction with the graphics + * bitmap buffer (CGRAM). The contents of the graphics buffer is + * XORed with the data from the character generator. This allows + * us to make the progress bar out of graphical data (the bar) and + * text data (the percentage). + */ + void ST7920_Lite_Status_Screen::draw_progress_bar(const uint8_t value) { + #if HOTENDS == 1 + // If we have only one extruder, draw a long progress bar on the third line + constexpr uint8_t top = 1, // Top in pixels + bottom = 13, // Bottom in pixels + left = 8, // Left edge, in 16-bit words + width = 4; // Width of progress bar, in 16-bit words + #else + constexpr uint8_t top = 16 + 1, + bottom = 16 + 13, + left = 5, + width = 3; + #endif + const uint8_t char_pcnt = 100 / width; // How many percent does each 16-bit word represent? + + // Draw the progress bar as a bitmap in CGRAM + // This drawing is a mess and only produce readable result around 25% steps + // i.e. 74-76% look fine [|||||||||||||||||||||||| ], but 73% look like this: [|||||||||||||||| | ] + // meaning partially filled bytes produce only single vertical line, and i bet they're not supposed to! + LOOP_S_LE_N(y, top, bottom) { + set_gdram_address(left, y); + begin_data(); + LOOP_L_N(x, width) { + uint16_t gfx_word = 0x0000; + if ((x + 1) * char_pcnt <= value) + gfx_word = 0xFFFF; // Draw completely filled bytes + else if ((x * char_pcnt) < value) + gfx_word = int16_t(0x8000) >> (value % char_pcnt) * 16 / char_pcnt; // Draw partially filled bytes + + // Draw the frame around the progress bar + if (y == top || y == bottom) + gfx_word = 0xFFFF; // Draw top/bottom border + else if (x == width - 1) + gfx_word |= 0x0001; // Draw right border + else if (x == 0) + gfx_word |= 0x8000; // Draw left border + write_word(gfx_word); + } + } + + // // Draw the percentage as text in DDRAM + // #if HOTENDS == 1 + // set_ddram_address(DDRAM_LINE_3 + 4); + // begin_data(); + // write_byte(' '); + // #else + // set_ddram_address(DDRAM_LINE_2 + left); + // begin_data(); + // #endif + + // // Draw centered + // if (value > 9) + // write_number(value, 4); + // else + // write_number(value, 3); + // write_str(F("% ")); + } + + void ST7920_Lite_Status_Screen::update_progress(const bool forceUpdate) { + + // Since the progress bar involves writing + // quite a few bytes to GDRAM, only do this + // when an update is actually necessary. + + const uint8_t progress = ui.get_progress_percent(); + static uint8_t last_progress = 0; + if (forceUpdate || last_progress != progress/2) { + last_progress = progress/2; // Because progress bar turns out only 62||46px wide, we only need to redraw it every 2% + draw_progress_bar(progress); + } + } +#endif // HAS_PRINT_PROGRESS + void ST7920_Lite_Status_Screen::update_indicators(const bool forceUpdate) { if (forceUpdate || indicators_changed()) { const bool blink = ui.get_blink(); - const duration_t elapsed = print_job_timer.duration(); - duration_t remaining = TERN0(USE_M73_REMAINING_TIME, ui.get_remaining_time()); const uint16_t feedrate_perc = feedrate_percentage; const celsius_t extruder_1_temp = thermalManager.wholeDegHotend(0), extruder_1_target = thermalManager.degTargetHotend(0); @@ -736,30 +828,20 @@ void ST7920_Lite_Status_Screen::update_indicators(const bool forceUpdate) { TERN_(HAS_MULTI_HOTEND, draw_extruder_2_temp(extruder_2_temp, extruder_2_target, forceUpdate)); TERN_(HAS_HEATED_BED, draw_bed_temp(bed_temp, bed_target, forceUpdate)); + // Update the fan and bed animations uint8_t spd = thermalManager.fan_speed[0]; #if ENABLED(ADAPTIVE_FAN_SLOWING) if (!blink && thermalManager.fan_speed_scaler[0] < 128) spd = thermalManager.scaledFanSpeed(0, spd); #endif draw_fan_speed(thermalManager.pwmToPercent(spd)); - - // Draw elapsed/remaining time - const bool show_remaining = ENABLED(SHOW_REMAINING_TIME) && (DISABLED(ROTATE_PROGRESS_DISPLAY) || blink); - if (show_remaining && !remaining.second()) { - const auto progress = ui.get_progress_percent(); - if (progress) - remaining = elapsed.second() * (100 - progress) / progress; - } - if (show_remaining && remaining.second()) - draw_print_time(remaining, 'R'); - else - draw_print_time(elapsed); + if (spd) draw_fan_icon(blink); + TERN_(HAS_HEATED_BED, draw_heat_icon(bed_target > 0 && blink, bed_target > 0)); draw_feedrate_percentage(feedrate_perc); - // Update the fan and bed animations - if (spd) draw_fan_icon(blink); - TERN_(HAS_HEATED_BED, draw_heat_icon(bed_target > 0 && blink, bed_target > 0)); + // Update and draw progress strings + TERN_(HAS_PRINT_PROGRESS, ui.rotate_progress()); } } @@ -839,27 +921,6 @@ void ST7920_Lite_Status_Screen::update_status_or_position(bool forceUpdate) { #endif } -void ST7920_Lite_Status_Screen::update_progress(const bool forceUpdate) { - #if EITHER(LCD_SET_PROGRESS_MANUALLY, SDSUPPORT) - - // Since the progress bar involves writing - // quite a few bytes to GDRAM, only do this - // when an update is actually necessary. - - static uint8_t last_progress = 0; - const uint8_t progress = ui.get_progress_percent(); - if (forceUpdate || last_progress != progress) { - last_progress = progress; - draw_progress_bar(progress); - } - - #else - - UNUSED(forceUpdate); - - #endif -} - void ST7920_Lite_Status_Screen::update(const bool forceUpdate) { cs(); update_indicators(forceUpdate); @@ -902,7 +963,7 @@ void ST7920_Lite_Status_Screen::clear_text_buffer() { } void MarlinUI::draw_status_screen() { - ST7920_Lite_Status_Screen::update(false); + lightUI.update(false); } // This method is called before each screen update and @@ -912,9 +973,9 @@ void MarlinUI::lcd_in_status(const bool inStatus) { static bool lastInStatus = false; if (lastInStatus == inStatus) return; if ((lastInStatus = inStatus)) - ST7920_Lite_Status_Screen::on_entry(); + lightUI.on_entry(); else - ST7920_Lite_Status_Screen::on_exit(); + lightUI.on_exit(); } #endif // LIGHTWEIGHT_UI diff --git a/Marlin/src/lcd/dogm/status_screen_lite_ST7920.h b/Marlin/src/lcd/dogm/status_screen_lite_ST7920.h index 7fe878356b..d838ee1a3a 100644 --- a/Marlin/src/lcd/dogm/status_screen_lite_ST7920.h +++ b/Marlin/src/lcd/dogm/status_screen_lite_ST7920.h @@ -75,7 +75,6 @@ class ST7920_Lite_Status_Screen { protected: static void draw_degree_symbol(uint8_t x, uint8_t y, const bool draw); static void draw_static_elements(); - static void draw_progress_bar(const uint8_t value); static void draw_fan_icon(const bool whichIcon); static void draw_heat_icon(const bool whichIcon, const bool heating); static void draw_temps(uint8_t line, const int16_t temp, const int16_t target, bool showTarget, bool targetStateChange); @@ -83,7 +82,12 @@ class ST7920_Lite_Status_Screen { static void draw_extruder_2_temp(const int16_t temp, const int16_t target, bool forceUpdate=false); static void draw_bed_temp(const int16_t temp, const int16_t target, bool forceUpdate=false); static void draw_fan_speed(const uint8_t value); - static void draw_print_time(const duration_t &elapsed, char suffix=' '); + #if HAS_PRINT_PROGRESS + static void draw_progress_bar(const uint8_t value); + static char* prepare_time_string(const duration_t &time, char prefix=' '); + static void draw_progress_string(uint8_t addr, const char *str); + static void update_progress(const bool forceUpdate); + #endif static void draw_feedrate_percentage(const uint16_t percentage); static void draw_status_message(); static void draw_position(const xyze_pos_t &pos, bool position_known=true); @@ -96,11 +100,18 @@ class ST7920_Lite_Status_Screen { static void update_indicators(const bool forceUpdate); static void update_position(const bool forceUpdate, bool resetChecksum); static void update_status_or_position(bool forceUpdate); - static void update_progress(const bool forceUpdate); public: static void update(const bool forceUpdate); static void on_entry(); static void on_exit(); static void clear_text_buffer(); + #if HAS_PRINT_PROGRESS + static void drawPercent(); + static void drawRemain(); + static void drawInter(); + static void drawElapsed(); + #endif }; + +extern ST7920_Lite_Status_Screen lightUI; diff --git a/Marlin/src/lcd/e3v2/jyersui/dwin.cpp b/Marlin/src/lcd/e3v2/jyersui/dwin.cpp index df758da617..21f93c6b98 100644 --- a/Marlin/src/lcd/e3v2/jyersui/dwin.cpp +++ b/Marlin/src/lcd/e3v2/jyersui/dwin.cpp @@ -733,7 +733,7 @@ void CrealityDWINClass::Draw_Print_Screen() { Update_Status_Bar(true); Draw_Print_ProgressBar(); Draw_Print_ProgressElapsed(); - TERN_(USE_M73_REMAINING_TIME, Draw_Print_ProgressRemain()); + TERN_(SET_REMAINING_TIME, Draw_Print_ProgressRemain()); Draw_Print_Filename(true); } @@ -759,7 +759,7 @@ void CrealityDWINClass::Draw_Print_ProgressBar() { DWIN_Draw_String(false, DWIN_FONT_MENU, GetColor(eeprom_settings.progress_percent, Percent_Color), Color_Bg_Black, 133, 133, F("%")); } -#if ENABLED(USE_M73_REMAINING_TIME) +#if ENABLED(SET_REMAINING_TIME) void CrealityDWINClass::Draw_Print_ProgressRemain() { uint16_t remainingtime = ui.get_remaining_time(); @@ -2772,7 +2772,7 @@ void CrealityDWINClass::Menu_Item_Handler(uint8_t menu, uint8_t item, bool draw/ #if ENABLED(LIN_ADVANCE) case ADVANCED_LA: if (draw) { - Draw_Menu_Item(row, ICON_MaxAccelerated, F("Lin Advance Kp")); + Draw_Menu_Item(row, ICON_MaxAccelerated, F("Lin Advance K")); Draw_Float(planner.extruder_advance_K[0], row, false, 100); } else @@ -4565,8 +4565,8 @@ void CrealityDWINClass::Start_Print(bool sd) { } else strcpy_P(filename, PSTR("Host Print")); - TERN_(LCD_SET_PROGRESS_MANUALLY, ui.set_progress(0)); - TERN_(USE_M73_REMAINING_TIME, ui.set_remaining_time(0)); + TERN_(SET_PROGRESS_PERCENT, ui.set_progress(0)); + TERN_(SET_REMAINING_TIME, ui.set_remaining_time(0)); Draw_Print_Screen(); } } @@ -4575,8 +4575,8 @@ void CrealityDWINClass::Stop_Print() { printing = false; sdprint = false; thermalManager.cooldown(); - TERN_(LCD_SET_PROGRESS_MANUALLY, ui.set_progress(100 * (PROGRESS_SCALE))); - TERN_(USE_M73_REMAINING_TIME, ui.set_remaining_time(0)); + TERN_(SET_PROGRESS_PERCENT, ui.set_progress(100 * (PROGRESS_SCALE))); + TERN_(SET_REMAINING_TIME, ui.set_remaining_time(0)); Draw_Print_confirm(); } @@ -4653,7 +4653,7 @@ void CrealityDWINClass::Screen_Update() { if (process == Print) { Draw_Print_ProgressBar(); Draw_Print_ProgressElapsed(); - TERN_(USE_M73_REMAINING_TIME, Draw_Print_ProgressRemain()); + TERN_(SET_REMAINING_TIME, Draw_Print_ProgressRemain()); } } diff --git a/Marlin/src/lcd/e3v2/jyersui/dwin.h b/Marlin/src/lcd/e3v2/jyersui/dwin.h index 8985647cd1..7e213a65e5 100644 --- a/Marlin/src/lcd/e3v2/jyersui/dwin.h +++ b/Marlin/src/lcd/e3v2/jyersui/dwin.h @@ -188,7 +188,7 @@ public: static void Draw_Print_Screen(); static void Draw_Print_Filename(const bool reset=false); static void Draw_Print_ProgressBar(); - #if ENABLED(USE_M73_REMAINING_TIME) + #if ENABLED(SET_REMAINING_TIME) static void Draw_Print_ProgressRemain(); #endif static void Draw_Print_ProgressElapsed(); diff --git a/Marlin/src/lcd/e3v2/marlinui/ui_status_480x272.cpp b/Marlin/src/lcd/e3v2/marlinui/ui_status_480x272.cpp index 8024085ef7..0bd1b2ff2a 100644 --- a/Marlin/src/lcd/e3v2/marlinui/ui_status_480x272.cpp +++ b/Marlin/src/lcd/e3v2/marlinui/ui_status_480x272.cpp @@ -374,11 +374,11 @@ void MarlinUI::draw_status_screen() { #if ENABLED(DWIN_MARLINUI_PORTRAIT) - // Portrait mode only shows one value at a time, and will rotate if ROTATE_PROGRESS_DISPLAY + // Portrait mode only shows one value at a time, and will rotate if many are enabled dwin_string.set(); char prefix = ' '; #if ENABLED(SHOW_REMAINING_TIME) - if (TERN1(ROTATE_PROGRESS_DISPLAY, blink) && print_job_timer.isRunning()) { + if (blink && print_job_timer.isRunning()) { time = get_remaining_time(); prefix = 'R'; } @@ -447,7 +447,7 @@ void MarlinUI::draw_status_screen() { //if (pb_solid < old_solid) DWIN_Draw_Rectangle(1, Color_Bg_Black, pb_left + 1 + pb_solid, pb_top + 1, pb_right - 1, pb_bottom - 1); // Erase the rest - #if ENABLED(SHOW_SD_PERCENT) + #if ENABLED(SHOW_PROGRESS_PERCENT) dwin_string.set(TERN(PRINT_PROGRESS_SHOW_DECIMALS, permyriadtostr4(progress), ui8tostr3rj(progress / (PROGRESS_SCALE)))); dwin_string.add('%'); DWIN_Draw_String( diff --git a/Marlin/src/lcd/e3v2/proui/dwin.cpp b/Marlin/src/lcd/e3v2/proui/dwin.cpp index 30f34c4772..c59df59c76 100644 --- a/Marlin/src/lcd/e3v2/proui/dwin.cpp +++ b/Marlin/src/lcd/e3v2/proui/dwin.cpp @@ -43,8 +43,8 @@ #if DISABLED(INDIVIDUAL_AXIS_HOMING_SUBMENU) #warning "INDIVIDUAL_AXIS_HOMING_SUBMENU is recommended with ProUI." #endif -#if DISABLED(LCD_SET_PROGRESS_MANUALLY) - #warning "LCD_SET_PROGRESS_MANUALLY is recommended with ProUI." +#if DISABLED(SET_PROGRESS_MANUALLY) + #warning "SET_PROGRESS_MANUALLY is recommended with ProUI." #endif #if DISABLED(STATUS_MESSAGE_SCROLLING) #warning "STATUS_MESSAGE_SCROLLING is recommended with ProUI." diff --git a/Marlin/src/lcd/extui/anycubic_i3mega/anycubic_i3mega_lcd.cpp b/Marlin/src/lcd/extui/anycubic_i3mega/anycubic_i3mega_lcd.cpp index 0da8bb36a7..03997fa95b 100644 --- a/Marlin/src/lcd/extui/anycubic_i3mega/anycubic_i3mega_lcd.cpp +++ b/Marlin/src/lcd/extui/anycubic_i3mega/anycubic_i3mega_lcd.cpp @@ -46,6 +46,12 @@ #define SENDLINE_DBG_PGM_VAL(x,y,z) sendLine_P(PSTR(x)) #endif +// Append ".gcode" to filename, if requested. Used for some DGUS-clone displays with built-in filter. +// Filenames are limited to 26 characters, so the actual name for the FILENAME can be 20 characters at most. +// If a longer string is desired without "extension, use the ALTNAME macro to provide a (longer) alternative. +#define SPECIAL_MENU_FILENAME(A) A TERN_(ANYCUBIC_LCD_GCODE_EXT, ".gcode") +#define SPECIAL_MENU_ALTNAME(A, B) TERN(ANYCUBIC_LCD_GCODE_EXT, A ".gcode", B) + AnycubicTFTClass AnycubicTFT; char AnycubicTFTClass::TFTcmdbuffer[TFTBUFSIZE][TFT_MAX_CMD_SIZE]; @@ -383,8 +389,8 @@ void AnycubicTFTClass::RenderCurrentFileList() { if (!isMediaInserted() && !SpecialMenu) { SENDLINE_DBG_PGM("J02", "TFT Serial Debug: No SD Card mounted to render Current File List... J02"); - SENDLINE_PGM(""); - SENDLINE_PGM(""); + SENDLINE_PGM("")); } else { if (CodeSeen('S')) @@ -403,58 +409,58 @@ void AnycubicTFTClass::RenderSpecialMenu(uint16_t selectedNumber) { switch (selectedNumber) { #if ENABLED(PROBE_MANUALLY) case 0: // First Page - SENDLINE_PGM("<01ZUp0.1>"); - SENDLINE_PGM(""); - SENDLINE_PGM("<02ZUp0.02>"); - SENDLINE_PGM(""); - SENDLINE_PGM("<03ZDn0.02>"); - SENDLINE_PGM(""); - SENDLINE_PGM("<04ZDn0.1>"); - SENDLINE_PGM(""); + SENDLINE_PGM("<01ZUP~1.GCO"); + SENDLINE_PGM(SPECIAL_MENU_FILENAME("")); + SENDLINE_PGM("<02ZUP~1.GCO"); + SENDLINE_PGM(SPECIAL_MENU_FILENAME("")); + SENDLINE_PGM("<03ZDO~1.GCO"); + SENDLINE_PGM(SPECIAL_MENU_FILENAME("")); + SENDLINE_PGM("<04ZDO~1.GCO"); + SENDLINE_PGM(SPECIAL_MENU_FILENAME("")); break; case 4: // Second Page - SENDLINE_PGM("<05PrehtBed>"); - SENDLINE_PGM(""); - SENDLINE_PGM("<06SMeshLvl>"); - SENDLINE_PGM(""); - SENDLINE_PGM("<07MeshNPnt>"); - SENDLINE_PGM(""); - SENDLINE_PGM("<08HtEndPID>"); - SENDLINE_PGM(""); + SENDLINE_PGM("<05PRE~1.GCO"); + SENDLINE_PGM(SPECIAL_MENU_FILENAME("")); + SENDLINE_PGM("<06MES~1.GCO"); + SENDLINE_PGM(SPECIAL_MENU_ALTNAME("", "")); + SENDLINE_PGM("<07NEX~1.GCO"); + SENDLINE_PGM(SPECIAL_MENU_FILENAME("")); + SENDLINE_PGM("<08PID~1.GCO"); + SENDLINE_PGM(SPECIAL_MENU_FILENAME("")); break; case 8: // Third Page - SENDLINE_PGM("<09HtBedPID>"); - SENDLINE_PGM(""); - SENDLINE_PGM("<10FWDeflts>"); - SENDLINE_PGM(""); - SENDLINE_PGM("<11SvEEPROM>"); - SENDLINE_PGM(""); - SENDLINE_PGM(""); - SENDLINE_PGM(""); + SENDLINE_PGM("<09PID~1.GCO"); + SENDLINE_PGM(SPECIAL_MENU_FILENAME("")); + SENDLINE_PGM("<10FWD~1.GCO"); + SENDLINE_PGM(SPECIAL_MENU_FILENAME("")); + SENDLINE_PGM("<11SAV~1.GCO"); + SENDLINE_PGM(SPECIAL_MENU_FILENAME("")); + SENDLINE_PGM("")); break; #else case 0: // First Page - SENDLINE_PGM("<01PrehtBed>"); - SENDLINE_PGM(""); - SENDLINE_PGM("<02ABL>"); - SENDLINE_PGM(""); - SENDLINE_PGM("<03HtEndPID>"); - SENDLINE_PGM(""); - SENDLINE_PGM("<04HtBedPID>"); - SENDLINE_PGM(""); + SENDLINE_PGM("<01PRE~1.GCO"); + SENDLINE_PGM(SPECIAL_MENU_FILENAME("")); + SENDLINE_PGM("<02ABL~1.GCO"); + SENDLINE_PGM(SPECIAL_MENU_FILENAME("")); + SENDLINE_PGM("<03PID~1.GCO"); + SENDLINE_PGM(SPECIAL_MENU_ALTNAME("", "")); + SENDLINE_PGM("<04PID~1.GCO"); + SENDLINE_PGM(SPECIAL_MENU_ALTNAME("", "")); break; case 4: // Second Page - SENDLINE_PGM("<05FWDeflts>"); - SENDLINE_PGM(""); - SENDLINE_PGM("<06SvEEPROM>"); - SENDLINE_PGM(""); - SENDLINE_PGM("<07SendM108>"); - SENDLINE_PGM(""); - SENDLINE_PGM(""); - SENDLINE_PGM(""); + SENDLINE_PGM("<05FWD~1.GCO"); + SENDLINE_PGM(SPECIAL_MENU_FILENAME("")); + SENDLINE_PGM("<06SAV~1.GCO"); + SENDLINE_PGM(SPECIAL_MENU_FILENAME("")); + SENDLINE_PGM("<06SEN~1.GCO"); + SENDLINE_PGM(SPECIAL_MENU_ALTNAME("", "")); + SENDLINE_PGM("")); break; #endif // PROBE_MANUALLY @@ -478,8 +484,8 @@ void AnycubicTFTClass::RenderCurrentFolder(uint16_t selectedNumber) { for (cnt = selectedNumber; cnt <= max_files; cnt++) { if (cnt == 0) { // Special Entry if (currentFileList.isAtRootDir()) { - SENDLINE_PGM(""); - SENDLINE_PGM(""); + SENDLINE_PGM("")); } else { SENDLINE_PGM("/.."); diff --git a/Marlin/src/lcd/extui/dgus/fysetc/DGUSDisplayDef.cpp b/Marlin/src/lcd/extui/dgus/fysetc/DGUSDisplayDef.cpp index a4c0997bf8..0e825c9e7c 100644 --- a/Marlin/src/lcd/extui/dgus/fysetc/DGUSDisplayDef.cpp +++ b/Marlin/src/lcd/extui/dgus/fysetc/DGUSDisplayDef.cpp @@ -63,7 +63,7 @@ const uint16_t VPList_Main[] PROGMEM = { VP_XPos, VP_YPos, VP_ZPos, VP_Fan0_Percentage, VP_Feedrate_Percentage, - #if ENABLED(LCD_SET_PROGRESS_MANUALLY) + #if ENABLED(SET_PROGRESS_PERCENT) VP_PrintProgress_Percentage, #endif 0x0000 diff --git a/Marlin/src/lcd/extui/dgus/hiprecy/DGUSDisplayDef.cpp b/Marlin/src/lcd/extui/dgus/hiprecy/DGUSDisplayDef.cpp index 4c850183da..6e4c76ca68 100644 --- a/Marlin/src/lcd/extui/dgus/hiprecy/DGUSDisplayDef.cpp +++ b/Marlin/src/lcd/extui/dgus/hiprecy/DGUSDisplayDef.cpp @@ -63,7 +63,7 @@ const uint16_t VPList_Main[] PROGMEM = { VP_XPos, VP_YPos, VP_ZPos, VP_Fan0_Percentage, VP_Feedrate_Percentage, - #if ENABLED(LCD_SET_PROGRESS_MANUALLY) + #if ENABLED(SET_PROGRESS_PERCENT) VP_PrintProgress_Percentage, #endif 0x0000 diff --git a/Marlin/src/lcd/extui/dgus/mks/DGUSDisplayDef.cpp b/Marlin/src/lcd/extui/dgus/mks/DGUSDisplayDef.cpp index 86920d6841..ae8d9565e3 100644 --- a/Marlin/src/lcd/extui/dgus/mks/DGUSDisplayDef.cpp +++ b/Marlin/src/lcd/extui/dgus/mks/DGUSDisplayDef.cpp @@ -135,7 +135,7 @@ const uint16_t VPList_Main[] PROGMEM = { VP_XPos, VP_YPos, VP_ZPos, VP_Fan0_Percentage, VP_Feedrate_Percentage, - #if ENABLED(LCD_SET_PROGRESS_MANUALLY) + #if ENABLED(SET_PROGRESS_PERCENT) VP_PrintProgress_Percentage, #endif 0x0000 diff --git a/Marlin/src/lcd/extui/dgus_reloaded/DGUSDisplay.h b/Marlin/src/lcd/extui/dgus_reloaded/DGUSDisplay.h index d115f7c02b..c4e3645f28 100644 --- a/Marlin/src/lcd/extui/dgus_reloaded/DGUSDisplay.h +++ b/Marlin/src/lcd/extui/dgus_reloaded/DGUSDisplay.h @@ -33,7 +33,7 @@ #include "../../../inc/MarlinConfigPre.h" #include "../../../MarlinCore.h" -#define DEBUG_DGUSLCD // Uncomment for debug messages +//#define DEBUG_DGUSLCD // Uncomment for debug messages #define DEBUG_OUT ENABLED(DEBUG_DGUSLCD) #include "../../../core/debug_out.h" diff --git a/Marlin/src/lcd/extui/mks_ui/draw_printing.cpp b/Marlin/src/lcd/extui/mks_ui/draw_printing.cpp index be596c8740..5dc3861f65 100644 --- a/Marlin/src/lcd/extui/mks_ui/draw_printing.cpp +++ b/Marlin/src/lcd/extui/mks_ui/draw_printing.cpp @@ -39,7 +39,7 @@ #include "../../../feature/powerloss.h" #endif -#if BOTH(LCD_SET_PROGRESS_MANUALLY, USE_M73_REMAINING_TIME) +#if ENABLED(SET_REMAINING_TIME) #include "../../marlinui.h" #endif @@ -244,7 +244,7 @@ void disp_fan_speed() { } void disp_print_time() { - #if BOTH(LCD_SET_PROGRESS_MANUALLY, USE_M73_REMAINING_TIME) + #if ENABLED(SET_REMAINING_TIME) const uint32_t r = ui.get_remaining_time(); sprintf_P(public_buf_l, PSTR("%02d:%02d R"), r / 3600, (r % 3600) / 60); #else diff --git a/Marlin/src/lcd/extui/ui_api.cpp b/Marlin/src/lcd/extui/ui_api.cpp index 40fb355f30..b4e6c54c81 100644 --- a/Marlin/src/lcd/extui/ui_api.cpp +++ b/Marlin/src/lcd/extui/ui_api.cpp @@ -709,17 +709,17 @@ namespace ExtUI { #if ENABLED(POWER_LOSS_RECOVERY) bool getPowerLossRecoveryEnabled() { return recovery.enabled; } - void setPowerLossRecoveryEnabled(const bool value) { recovery.enable(value); } + void setPowerLossRecoveryEnabled(const bool value) { recovery.enable(value); } #endif #if ENABLED(LIN_ADVANCE) float getLinearAdvance_mm_mm_s(const extruder_t extruder) { - return (extruder < EXTRUDERS) ? planner.extruder_advance_K[extruder - E0] : 0; + return (extruder < EXTRUDERS) ? planner.extruder_advance_K[E_INDEX_N(extruder - E0)] : 0; } void setLinearAdvance_mm_mm_s(const_float_t value, const extruder_t extruder) { if (extruder < EXTRUDERS) - planner.extruder_advance_K[extruder - E0] = constrain(value, 0, 10); + planner.extruder_advance_K[E_INDEX_N(extruder - E0)] = constrain(value, 0, 10); } #endif diff --git a/Marlin/src/lcd/extui/ui_api.h b/Marlin/src/lcd/extui/ui_api.h index 5feab86fec..6de62a79e3 100644 --- a/Marlin/src/lcd/extui/ui_api.h +++ b/Marlin/src/lcd/extui/ui_api.h @@ -164,6 +164,9 @@ namespace ExtUI { #if ENABLED(SHOW_REMAINING_TIME) inline uint32_t getProgress_seconds_remaining() { return ui.get_remaining_time(); } #endif + #if ENABLED(SHOW_INTERACTION_TIME) + inline uint32_t getInteraction_seconds_remaining() { return ui.interaction_time; } + #endif #if HAS_LEVELING bool getLevelingActive(); diff --git a/Marlin/src/lcd/language/language_en.h b/Marlin/src/lcd/language/language_en.h index ab9dde5254..9f75fb9d17 100644 --- a/Marlin/src/lcd/language/language_en.h +++ b/Marlin/src/lcd/language/language_en.h @@ -418,6 +418,12 @@ namespace Language_en { LSTR MSG_FILAMENT_DIAM_E = _UxGT("Fil. Dia. *"); LSTR MSG_FILAMENT_UNLOAD = _UxGT("Unload mm"); LSTR MSG_FILAMENT_LOAD = _UxGT("Load mm"); + LSTR MSG_SEGMENTS_PER_SECOND = _UxGT("Segments/Sec"); + LSTR MSG_DRAW_MIN_X = _UxGT("Draw Min X"); + LSTR MSG_DRAW_MAX_X = _UxGT("Draw Max X"); + LSTR MSG_DRAW_MIN_Y = _UxGT("Draw Min Y"); + LSTR MSG_DRAW_MAX_Y = _UxGT("Draw Max Y"); + LSTR MSG_MAX_BELT_LEN = _UxGT("Max Belt Len"); LSTR MSG_ADVANCE_K = _UxGT("Advance K"); LSTR MSG_ADVANCE_K_E = _UxGT("Advance K *"); LSTR MSG_CONTRAST = _UxGT("LCD Contrast"); diff --git a/Marlin/src/lcd/marlinui.cpp b/Marlin/src/lcd/marlinui.cpp index 1527426949..e559f06961 100644 --- a/Marlin/src/lcd/marlinui.cpp +++ b/Marlin/src/lcd/marlinui.cpp @@ -79,11 +79,16 @@ constexpr uint8_t epps = ENCODER_PULSES_PER_STEP; statusResetFunc_t MarlinUI::status_reset_callback; // = nullptr #endif -#if ENABLED(LCD_SET_PROGRESS_MANUALLY) - MarlinUI::progress_t MarlinUI::progress_override; // = 0 - #if ENABLED(USE_M73_REMAINING_TIME) +#if ENABLED(SET_PROGRESS_MANUALLY) + #if ENABLED(SET_PROGRESS_PERCENT) + MarlinUI::progress_t MarlinUI::progress_override; // = 0 + #endif + #if ENABLED(SET_REMAINING_TIME) uint32_t MarlinUI::remaining_time; #endif + #if ENABLED(SET_INTERACTION_TIME) + uint32_t MarlinUI::interaction_time; + #endif #endif #if HAS_MULTI_LANGUAGE @@ -153,7 +158,7 @@ constexpr uint8_t epps = ENCODER_PULSES_PER_STEP; bool MarlinUI::lcd_clicked; #endif -#if EITHER(HAS_WIRED_LCD, DWIN_CREALITY_LCD_JYERSUI) +#if LCD_WITH_BLINK bool MarlinUI::get_blink() { static uint8_t blink = 0; @@ -191,11 +196,12 @@ constexpr uint8_t epps = ENCODER_PULSES_PER_STEP; uint8_t MarlinUI::sleep_timeout_minutes; // Initialized by settings.load() millis_t MarlinUI::screen_timeout_millis = 0; - void MarlinUI::refresh_screen_timeout() { - screen_timeout_millis = sleep_timeout_minutes ? millis() + sleep_timeout_minutes * 60UL * 1000UL : 0; - sleep_display(false); - } - + #if DISABLED(TFT_COLOR_UI) + void MarlinUI::refresh_screen_timeout() { + screen_timeout_millis = sleep_timeout_minutes ? millis() + sleep_timeout_minutes * 60UL * 1000UL : 0; + sleep_display(false); + } + #endif #endif void MarlinUI::init() { @@ -1067,7 +1073,7 @@ void MarlinUI::init() { #if LCD_BACKLIGHT_TIMEOUT_MINS refresh_backlight_timeout(); - #elif HAS_DISPLAY_SLEEP + #elif HAS_DISPLAY_SLEEP && DISABLED(TFT_COLOR_UI) refresh_screen_timeout(); #endif @@ -1180,9 +1186,9 @@ void MarlinUI::init() { WRITE(LCD_BACKLIGHT_PIN, LOW); // Backlight off backlight_off_ms = 0; } - #elif HAS_DISPLAY_SLEEP + #elif HAS_DISPLAY_SLEEP && DISABLED(TFT_COLOR_UI) if (screen_timeout_millis && ELAPSED(ms, screen_timeout_millis)) - sleep_display(); + sleep_display(true); #endif // Change state of drawing flag between screen updates @@ -1678,19 +1684,6 @@ void MarlinUI::init() { print_job_timer.start(); // Also called by M24 } - #if HAS_PRINT_PROGRESS - - MarlinUI::progress_t MarlinUI::_get_progress() { - return ( - TERN0(LCD_SET_PROGRESS_MANUALLY, (progress_override & PROGRESS_MASK)) - #if ENABLED(SDSUPPORT) - ?: TERN(HAS_PRINT_PROGRESS_PERMYRIAD, card.permyriadDone(), card.percentDone()) - #endif - ); - } - - #endif - #if HAS_TOUCH_BUTTONS // @@ -1724,6 +1717,38 @@ void MarlinUI::init() { #endif // HAS_DISPLAY +#if HAS_PRINT_PROGRESS + + MarlinUI::progress_t MarlinUI::_get_progress() { + return ( + TERN0(SET_PROGRESS_PERCENT, (progress_override & PROGRESS_MASK)) + #if ENABLED(SDSUPPORT) + ?: TERN(HAS_PRINT_PROGRESS_PERMYRIAD, card.permyriadDone(), card.percentDone()) + #endif + ); + } + + #if LCD_WITH_BLINK && DISABLED(HAS_GRAPHICAL_TFT) + typedef void (*PrintProgress_t)(); + void MarlinUI::rotate_progress() { // Renew and redraw all enabled progress strings + const PrintProgress_t progFunc[] = { + OPTITEM(SHOW_PROGRESS_PERCENT, drawPercent) + OPTITEM(SHOW_ELAPSED_TIME, drawElapsed) + OPTITEM(SHOW_REMAINING_TIME, drawRemain) + OPTITEM(SHOW_INTERACTION_TIME, drawInter) + }; + static bool prev_blink; + static uint8_t i; + if (prev_blink != get_blink()) { + prev_blink = get_blink(); + if (++i >= COUNT(progFunc)) i = 0; + (*progFunc[i])(); + } + } + #endif + +#endif // HAS_PRINT_PROGRESS + #if ENABLED(SDSUPPORT) #if ENABLED(EXTENSIBLE_UI) diff --git a/Marlin/src/lcd/marlinui.h b/Marlin/src/lcd/marlinui.h index d2e3708907..b1a98248bb 100644 --- a/Marlin/src/lcd/marlinui.h +++ b/Marlin/src/lcd/marlinui.h @@ -25,7 +25,6 @@ #include "../sd/cardreader.h" #include "../module/motion.h" #include "../libs/buzzer.h" - #include "buttons.h" #if ENABLED(TOUCH_SCREEN_CALIBRATION) @@ -36,7 +35,7 @@ #define MULTI_E_MANUAL 1 #endif -#if HAS_DISPLAY +#if HAS_PRINT_PROGRESS #include "../module/printcounter.h" #endif @@ -86,6 +85,7 @@ typedef bool (*statusResetFunc_t)(); #endif // HAS_WIRED_LCD #if EITHER(HAS_WIRED_LCD, DWIN_CREALITY_LCD_JYERSUI) + #define LCD_WITH_BLINK 1 #define LCD_UPDATE_INTERVAL TERN(HAS_TOUCH_BUTTONS, 50, 100) #endif @@ -303,19 +303,19 @@ public: #define PROGRESS_SCALE 1U #define PROGRESS_MASK 0x7F #endif - #if ENABLED(LCD_SET_PROGRESS_MANUALLY) + #if ENABLED(SET_PROGRESS_PERCENT) static progress_t progress_override; static void set_progress(const progress_t p) { progress_override = _MIN(p, 100U * (PROGRESS_SCALE)); } static void set_progress_done() { progress_override = (PROGRESS_MASK + 1U) + 100U * (PROGRESS_SCALE); } static void progress_reset() { if (progress_override & (PROGRESS_MASK + 1U)) set_progress(0); } #endif - #if ENABLED(SHOW_REMAINING_TIME) + #if EITHER(SHOW_REMAINING_TIME, SET_PROGRESS_MANUALLY) static uint32_t _calculated_remaining_time() { const duration_t elapsed = print_job_timer.duration(); const progress_t progress = _get_progress(); return progress ? elapsed.value * (100 * (PROGRESS_SCALE) - progress) / progress : 0; } - #if ENABLED(USE_M73_REMAINING_TIME) + #if ENABLED(SET_REMAINING_TIME) static uint32_t remaining_time; FORCE_INLINE static void set_remaining_time(const uint32_t r) { remaining_time = r; } FORCE_INLINE static uint32_t get_remaining_time() { return remaining_time ?: _calculated_remaining_time(); } @@ -323,12 +323,32 @@ public: #else FORCE_INLINE static uint32_t get_remaining_time() { return _calculated_remaining_time(); } #endif + #if ENABLED(SET_INTERACTION_TIME) + static uint32_t interaction_time; + FORCE_INLINE static void set_interaction_time(const uint32_t r) { interaction_time = r; } + FORCE_INLINE static void reset_interaction_time() { set_interaction_time(0); } + #endif #endif static progress_t _get_progress(); #if HAS_PRINT_PROGRESS_PERMYRIAD FORCE_INLINE static uint16_t get_progress_permyriad() { return _get_progress(); } #endif static uint8_t get_progress_percent() { return uint8_t(_get_progress() / (PROGRESS_SCALE)); } + #if LCD_WITH_BLINK + #if ENABLED(SHOW_PROGRESS_PERCENT) + static void drawPercent(); + #endif + #if ENABLED(SHOW_ELAPSED_TIME) + static void drawElapsed(); + #endif + #if ENABLED(SHOW_REMAINING_TIME) + static void drawRemain(); + #endif + #if ENABLED(SHOW_INTERACTION_TIME) + static void drawInter(); + #endif + static void rotate_progress(); + #endif #else static constexpr uint8_t get_progress_percent() { return 0; } #endif @@ -390,7 +410,7 @@ public: static void poweroff(); #endif - #if EITHER(HAS_WIRED_LCD, DWIN_CREALITY_LCD_JYERSUI) + #if LCD_WITH_BLINK static bool get_blink(); #endif diff --git a/Marlin/src/lcd/menu/menu.cpp b/Marlin/src/lcd/menu/menu.cpp index 9dd74988f3..7ae1078f4d 100644 --- a/Marlin/src/lcd/menu/menu.cpp +++ b/Marlin/src/lcd/menu/menu.cpp @@ -175,7 +175,7 @@ void MarlinUI::goto_screen(screenFunc_t screen, const uint16_t encoder/*=0*/, co TERN_(HAS_TOUCH_BUTTONS, repeat_delay = BUTTON_DELAY_MENU); - TERN_(LCD_SET_PROGRESS_MANUALLY, progress_reset()); + TERN_(SET_PROGRESS_PERCENT, progress_reset()); #if BOTH(DOUBLECLICK_FOR_Z_BABYSTEPPING, BABYSTEPPING) static millis_t doubleclick_expire_ms = 0; diff --git a/Marlin/src/lcd/menu/menu_advanced.cpp b/Marlin/src/lcd/menu/menu_advanced.cpp index 755b0b4897..e39233134d 100644 --- a/Marlin/src/lcd/menu/menu_advanced.cpp +++ b/Marlin/src/lcd/menu/menu_advanced.cpp @@ -157,9 +157,9 @@ void menu_backlash(); BACK_ITEM(MSG_ADVANCED_SETTINGS); #if ENABLED(LIN_ADVANCE) - #if EXTRUDERS == 1 + #if DISTINCT_E < 2 EDIT_ITEM(float42_52, MSG_ADVANCE_K, &planner.extruder_advance_K[0], 0, 10); - #elif HAS_MULTI_EXTRUDER + #else EXTRUDER_LOOP() EDIT_ITEM_N(float42_52, e, MSG_ADVANCE_K_E, &planner.extruder_advance_K[e], 0, 10); #endif @@ -677,10 +677,20 @@ void menu_advanced_settings() { #if DISABLED(SLIM_LCD_MENUS) + #if ENABLED(POLARGRAPH) + // M665 - Polargraph Settings + if (!is_busy) { + EDIT_ITEM_FAST(float4, MSG_SEGMENTS_PER_SECOND, &segments_per_second, 100, 9999); // M665 S + EDIT_ITEM_FAST(float51sign, MSG_DRAW_MIN_X, &draw_area_min.x, X_MIN_POS, draw_area_max.x - 10); // M665 L + EDIT_ITEM_FAST(float51sign, MSG_DRAW_MAX_X, &draw_area_max.x, draw_area_min.x + 10, X_MAX_POS); // M665 R + EDIT_ITEM_FAST(float51sign, MSG_DRAW_MIN_Y, &draw_area_min.y, Y_MIN_POS, draw_area_max.y - 10); // M665 T + EDIT_ITEM_FAST(float51sign, MSG_DRAW_MAX_Y, &draw_area_max.y, draw_area_min.y + 10, Y_MAX_POS); // M665 B + EDIT_ITEM_FAST(float51sign, MSG_MAX_BELT_LEN, &polargraph_max_belt_len, 500, 2000); // M665 H + } + #endif + #if HAS_M206_COMMAND - // - // Set Home Offsets - // + // M428 - Set Home Offsets ACTION_ITEM(MSG_SET_HOME_OFFSETS, []{ queue.inject(F("M428")); ui.return_to_status(); }); #endif @@ -732,11 +742,11 @@ void menu_advanced_settings() { #if DISABLED(NO_VOLUMETRICS) || ENABLED(ADVANCED_PAUSE_FEATURE) SUBMENU(MSG_FILAMENT, menu_advanced_filament); #elif ENABLED(LIN_ADVANCE) - #if EXTRUDERS == 1 + #if DISTINCT_E < 2 EDIT_ITEM(float42_52, MSG_ADVANCE_K, &planner.extruder_advance_K[0], 0, 10); - #elif HAS_MULTI_EXTRUDER - LOOP_L_N(n, E_STEPPERS) - EDIT_ITEM_N(float42_52, n, MSG_ADVANCE_K_E, &planner.extruder_advance_K[n], 0, 10); + #else + EXTRUDER_LOOP() + EDIT_ITEM_N(float42_52, n, MSG_ADVANCE_K_E, &planner.extruder_advance_K[e], 0, 10); #endif #endif diff --git a/Marlin/src/lcd/menu/menu_configuration.cpp b/Marlin/src/lcd/menu/menu_configuration.cpp index 6592ffff7b..63f4a28c1b 100644 --- a/Marlin/src/lcd/menu/menu_configuration.cpp +++ b/Marlin/src/lcd/menu/menu_configuration.cpp @@ -550,7 +550,7 @@ void menu_configuration() { // #if LCD_BACKLIGHT_TIMEOUT_MINS EDIT_ITEM(uint8, MSG_SCREEN_TIMEOUT, &ui.backlight_timeout_minutes, ui.backlight_timeout_min, ui.backlight_timeout_max, ui.refresh_backlight_timeout); - #elif HAS_DISPLAY_SLEEP + #elif HAS_DISPLAY_SLEEP && DISABLED(TFT_COLOR_UI) EDIT_ITEM(uint8, MSG_SCREEN_TIMEOUT, &ui.sleep_timeout_minutes, ui.sleep_timeout_min, ui.sleep_timeout_max, ui.refresh_screen_timeout); #endif diff --git a/Marlin/src/lcd/menu/menu_tune.cpp b/Marlin/src/lcd/menu/menu_tune.cpp index bc52001967..79d87bb6ca 100644 --- a/Marlin/src/lcd/menu/menu_tune.cpp +++ b/Marlin/src/lcd/menu/menu_tune.cpp @@ -210,9 +210,9 @@ void menu_tune() { // Advance K: // #if ENABLED(LIN_ADVANCE) && DISABLED(SLIM_LCD_MENUS) - #if EXTRUDERS == 1 + #if DISTINCT_E < 2 EDIT_ITEM(float42_52, MSG_ADVANCE_K, &planner.extruder_advance_K[0], 0, 10); - #elif HAS_MULTI_EXTRUDER + #else EXTRUDER_LOOP() EDIT_ITEM_N(float42_52, e, MSG_ADVANCE_K_E, &planner.extruder_advance_K[e], 0, 10); #endif diff --git a/Marlin/src/lcd/thermistornames.h b/Marlin/src/lcd/thermistornames.h index 2571efe075..54542bed4e 100644 --- a/Marlin/src/lcd/thermistornames.h +++ b/Marlin/src/lcd/thermistornames.h @@ -124,6 +124,8 @@ #define THERMISTOR_NAME "ATC104GT-2 1K" #elif THERMISTOR_ID == 1047 #define THERMISTOR_NAME "PT1000 4K7" +#elif THERMISTOR_ID == 1022 + #define THERMISTOR_NAME "PT1000 2K2" #elif THERMISTOR_ID == 1010 #define THERMISTOR_NAME "PT1000 1K" #elif THERMISTOR_ID == 147 @@ -139,7 +141,7 @@ #elif THERMISTOR_ID == 61 #define THERMISTOR_NAME "Formbot 350°C" #elif THERMISTOR_ID == 66 - #define THERMISTOR_NAME "Dyze 4.7M" + #define THERMISTOR_NAME "Dyze / TL 4.7M" #elif THERMISTOR_ID == 67 #define THERMISTOR_NAME "SliceEng 450°C" diff --git a/Marlin/src/libs/numtostr.cpp b/Marlin/src/libs/numtostr.cpp index f4d47983d2..594255aea8 100644 --- a/Marlin/src/libs/numtostr.cpp +++ b/Marlin/src/libs/numtostr.cpp @@ -73,10 +73,10 @@ const char* i8tostr3rj(const int8_t x) { } #if HAS_PRINT_PROGRESS_PERMYRIAD - // Convert unsigned 16-bit permyriad to percent with 100 / 23 / 23.4 / 3.45 format + // Convert unsigned 16-bit permyriad to percent with 100 / 23.4 / 3.45 format const char* permyriadtostr4(const uint16_t xx) { if (xx >= 10000) - return "100"; + return " 100"; // space to keep 4-width alignment else if (xx >= 1000) { conv[3] = DIGIMOD(xx, 1000); conv[4] = DIGIMOD(xx, 100); diff --git a/Marlin/src/libs/vector_3.h b/Marlin/src/libs/vector_3.h index f515333cc7..58bdb43c7b 100644 --- a/Marlin/src/libs/vector_3.h +++ b/Marlin/src/libs/vector_3.h @@ -75,8 +75,8 @@ struct vector_3 { vector_3 operator-(const vector_3 &v) { return vector_3(x - v.x, y - v.y, z - v.z); } vector_3 operator*(const float &v) { return vector_3(x * v, y * v, z * v); } - operator xy_float_t() { return xy_float_t({ x, y }); } - operator xyz_float_t() { return xyz_float_t({ x, y, z }); } + operator xy_float_t() { return xy_float_t({ x OPTARG(HAS_Y_AXIS, y) }); } + operator xyz_float_t() { return xyz_float_t({ x OPTARG(HAS_Y_AXIS, y) OPTARG(HAS_Z_AXIS, z) }); } void debug(FSTR_P const title); }; diff --git a/Marlin/src/module/motion.cpp b/Marlin/src/module/motion.cpp index c0503c621d..dadbfab297 100644 --- a/Marlin/src/module/motion.cpp +++ b/Marlin/src/module/motion.cpp @@ -341,7 +341,6 @@ void report_current_position_projected() { can_reach = ( a < polargraph_max_belt_len + 1 && b < polargraph_max_belt_len + 1 - && (a + b) > _MIN(draw_area_size.x, draw_area_size.y) ); #endif @@ -562,7 +561,8 @@ void do_blocking_move_to(NUM_AXIS_ARGS(const float), const_feedRate_t fr_mm_s/*= const feedRate_t w_feedrate = fr_mm_s ?: homing_feedrate(W_AXIS) ); - #if IS_KINEMATIC + #if IS_KINEMATIC && DISABLED(POLARGRAPH) + // kinematic machines are expected to home to a point 1.5x their range? never reachable. if (!position_is_reachable(x, y)) return; destination = current_position; // sync destination at the start #endif @@ -919,11 +919,16 @@ void restore_feedrate_and_scaling() { constexpr xy_pos_t offs{0}; #endif - if (TERN1(IS_SCARA, axis_was_homed(X_AXIS) && axis_was_homed(Y_AXIS))) { - const float dist_2 = HYPOT2(target.x - offs.x, target.y - offs.y); - if (dist_2 > delta_max_radius_2) - target *= float(delta_max_radius / SQRT(dist_2)); // 200 / 300 = 0.66 - } + #if ENABLED(POLARGRAPH) + LIMIT(target.x, draw_area_min.x, draw_area_max.x); + LIMIT(target.y, draw_area_min.y, draw_area_max.y); + #else + if (TERN1(IS_SCARA, axis_was_homed(X_AXIS) && axis_was_homed(Y_AXIS))) { + const float dist_2 = HYPOT2(target.x - offs.x, target.y - offs.y); + if (dist_2 > delta_max_radius_2) + target *= float(delta_max_radius / SQRT(dist_2)); // 200 / 300 = 0.66 + } + #endif #else diff --git a/Marlin/src/module/planner.cpp b/Marlin/src/module/planner.cpp index 1c9601632d..8da7f6e345 100644 --- a/Marlin/src/module/planner.cpp +++ b/Marlin/src/module/planner.cpp @@ -227,7 +227,7 @@ float Planner::previous_nominal_speed; #endif #if ENABLED(LIN_ADVANCE) - float Planner::extruder_advance_K[EXTRUDERS]; // Initialized by settings.load() + float Planner::extruder_advance_K[DISTINCT_E]; // Initialized by settings.load() #endif #if HAS_POSITION_FLOAT @@ -801,9 +801,12 @@ void Planner::calculate_trapezoid_for_block(block_t * const block, const_float_t decelerate_steps = 0; if (accel != 0) { - // Steps required for acceleration, deceleration to/from nominal rate - const float nominal_rate_sq = sq(float(block->nominal_rate)); - float accelerate_steps_float = (nominal_rate_sq - sq(float(initial_rate))) * (0.5f / accel); + inverse_accel = 1.0f / accel; + const float half_inverse_accel = 0.5f * inverse_accel, + nominal_rate_sq = sq(float(block->nominal_rate)), + // Steps required for acceleration, deceleration to/from nominal rate + decelerate_steps_float = half_inverse_accel * (nominal_rate_sq - sq(float(final_rate))); + float accelerate_steps_float = half_inverse_accel * (nominal_rate_sq - sq(float(initial_rate))); accelerate_steps = CEIL(accelerate_steps_float); const float decelerate_steps_float = (nominal_rate_sq - sq(float(final_rate))) * (0.5f / accel); decelerate_steps = FLOOR(decelerate_steps_float); @@ -851,7 +854,7 @@ void Planner::calculate_trapezoid_for_block(block_t * const block, const_float_t #if ENABLED(LIN_ADVANCE) if (block->la_advance_rate) { - const float comp = extruder_advance_K[block->extruder] * block->steps.e / block->step_event_count; + const float comp = extruder_advance_K[E_INDEX_N(block->extruder)] * block->steps.e / block->step_event_count; block->max_adv_steps = cruise_rate * comp; block->final_adv_steps = final_rate * comp; } @@ -2241,7 +2244,6 @@ bool Planner::_populate_block( TERN_(MIXING_EXTRUDER, mixer.populate_block(block->b_color)); - #if HAS_FAN FANS_LOOP(i) block->fan_speed[i] = thermalManager.fan_speed[i]; #endif @@ -2538,7 +2540,7 @@ bool Planner::_populate_block( * * de > 0 : Extruder is running forward (e.g., for "Wipe while retracting" (Slic3r) or "Combing" (Cura) moves) */ - use_advance_lead = esteps && extruder_advance_K[extruder] && de > 0; + use_advance_lead = esteps && extruder_advance_K[E_INDEX_N(extruder)] && de > 0; if (use_advance_lead) { float e_D_ratio = (target_float.e - position_float.e) / @@ -2554,7 +2556,7 @@ bool Planner::_populate_block( use_advance_lead = false; else { // Scale E acceleration so that it will be possible to jump to the advance speed. - const uint32_t max_accel_steps_per_s2 = MAX_E_JERK(extruder) / (extruder_advance_K[extruder] * e_D_ratio) * steps_per_mm; + const uint32_t max_accel_steps_per_s2 = MAX_E_JERK(extruder) / (extruder_advance_K[E_INDEX_N(extruder)] * e_D_ratio) * steps_per_mm; if (TERN0(LA_DEBUG, accel > max_accel_steps_per_s2)) SERIAL_ECHOLNPGM("Acceleration limited."); NOMORE(accel, max_accel_steps_per_s2); @@ -2591,7 +2593,7 @@ bool Planner::_populate_block( if (use_advance_lead) { // the Bresenham algorithm will convert this step rate into extruder steps - block->la_advance_rate = extruder_advance_K[extruder] * block->acceleration_steps_per_s2; + block->la_advance_rate = extruder_advance_K[E_INDEX_N(extruder)] * block->acceleration_steps_per_s2; // reduce LA ISR frequency by calling it only often enough to ensure that there will // never be more than four extruder steps per call diff --git a/Marlin/src/module/planner.h b/Marlin/src/module/planner.h index 09afee7db1..cfd7b45516 100644 --- a/Marlin/src/module/planner.h +++ b/Marlin/src/module/planner.h @@ -192,11 +192,11 @@ typedef struct PlannerBlock { volatile block_flags_t flag; // Block flags - volatile bool is_fan_sync() { return TERN0(LASER_SYNCHRONOUS_M106_M107, flag.sync_fans); } - volatile bool is_pwr_sync() { return TERN0(LASER_POWER_SYNC, flag.sync_laser_pwr); } - volatile bool is_sync() { return flag.sync_position || is_fan_sync() || is_pwr_sync(); } - volatile bool is_page() { return TERN0(DIRECT_STEPPING, flag.page); } - volatile bool is_move() { return !(is_sync() || is_page()); } + bool is_fan_sync() { return TERN0(LASER_SYNCHRONOUS_M106_M107, flag.sync_fans); } + bool is_pwr_sync() { return TERN0(LASER_POWER_SYNC, flag.sync_laser_pwr); } + bool is_sync() { return flag.sync_position || is_fan_sync() || is_pwr_sync(); } + bool is_page() { return TERN0(DIRECT_STEPPING, flag.page); } + bool is_move() { return !(is_sync() || is_page()); } // Fields used by the motion planner to manage acceleration float nominal_speed, // The nominal speed for this block in (mm/sec) @@ -459,7 +459,7 @@ class Planner { #endif #if ENABLED(LIN_ADVANCE) - static float extruder_advance_K[EXTRUDERS]; + static float extruder_advance_K[DISTINCT_E]; #endif /** diff --git a/Marlin/src/module/polargraph.cpp b/Marlin/src/module/polargraph.cpp index 42f99304d7..d55d36a6d6 100644 --- a/Marlin/src/module/polargraph.cpp +++ b/Marlin/src/module/polargraph.cpp @@ -37,17 +37,12 @@ #include "../lcd/marlinui.h" #include "../MarlinCore.h" -float segments_per_second; // Initialized by settings.load() - -xy_pos_t draw_area_min = { X_MIN_POS, Y_MIN_POS }, - draw_area_max = { X_MAX_POS, Y_MAX_POS }; - -xy_float_t draw_area_size = { X_MAX_POS - X_MIN_POS, Y_MAX_POS - Y_MIN_POS }; - -float polargraph_max_belt_len = HYPOT(draw_area_size.x, draw_area_size.y); +// Initialized by settings.load() +float segments_per_second, polargraph_max_belt_len; +xy_pos_t draw_area_min, draw_area_max; void inverse_kinematics(const xyz_pos_t &raw) { - const float x1 = raw.x - (draw_area_min.x), x2 = (draw_area_max.x) - raw.x, y = raw.y - (draw_area_max.y); + const float x1 = raw.x - draw_area_min.x, x2 = draw_area_max.x - raw.x, y = raw.y - draw_area_max.y; delta.set(HYPOT(x1, y), HYPOT(x2, y), raw.z); } diff --git a/Marlin/src/module/polargraph.h b/Marlin/src/module/polargraph.h index b465de3287..f4904ebfe2 100644 --- a/Marlin/src/module/polargraph.h +++ b/Marlin/src/module/polargraph.h @@ -30,7 +30,6 @@ extern float segments_per_second; extern xy_pos_t draw_area_min, draw_area_max; -extern xy_float_t draw_area_size; extern float polargraph_max_belt_len; void inverse_kinematics(const xyz_pos_t &raw); diff --git a/Marlin/src/module/probe.h b/Marlin/src/module/probe.h index 1bcbc65642..dc2ba45764 100644 --- a/Marlin/src/module/probe.h +++ b/Marlin/src/module/probe.h @@ -146,7 +146,7 @@ public: #else - static constexpr xyz_pos_t offset = xyz_pos_t(NUM_AXIS_ARRAY(0, 0, 0, 0, 0, 0)); // See #16767 + static constexpr xyz_pos_t offset = xyz_pos_t(NUM_AXIS_ARRAY_1(0)); // See #16767 static bool set_deployed(const bool) { return false; } diff --git a/Marlin/src/module/settings.cpp b/Marlin/src/module/settings.cpp index ae64257369..9d2604d6c6 100644 --- a/Marlin/src/module/settings.cpp +++ b/Marlin/src/module/settings.cpp @@ -115,8 +115,8 @@ #include "../feature/runout.h" #endif -#if ENABLED(EXTRA_LIN_ADVANCE_K) - extern float other_extruder_advance_K[EXTRUDERS]; +#if ENABLED(ADVANCE_K_EXTRA) + extern float other_extruder_advance_K[DISTINCT_E]; #endif #if HAS_MULTI_EXTRUDER @@ -257,7 +257,7 @@ typedef struct SettingsDataStruct { // HAS_BED_PROBE // - xyz_pos_t probe_offset; + xyz_pos_t probe_offset; // M851 X Y Z // // ABL_PLANAR @@ -330,7 +330,11 @@ typedef struct SettingsDataStruct { delta_diagonal_rod; // M665 L abc_float_t delta_tower_angle_trim, // M665 X Y Z delta_diagonal_rod_trim; // M665 A B C + #elif ENABLED(POLARGRAPH) + xy_pos_t draw_area_min, draw_area_max; // M665 L R T B + float polargraph_max_belt_len; // M665 H #endif + #endif // @@ -442,7 +446,7 @@ typedef struct SettingsDataStruct { // // LIN_ADVANCE // - float planner_extruder_advance_K[_MAX(EXTRUDERS, 1)]; // M900 K planner.extruder_advance_K + float planner_extruder_advance_K[DISTINCT_E]; // M900 K planner.extruder_advance_K // // HAS_MOTOR_CURRENT_PWM @@ -468,7 +472,7 @@ typedef struct SettingsDataStruct { // // SKEW_CORRECTION // - skew_factor_t planner_skew_factor; // M852 I J K planner.skew_factor + skew_factor_t planner_skew_factor; // M852 I J K // // ADVANCED_PAUSE_FEATURE @@ -642,7 +646,7 @@ void MarlinSettings::postprocess() { #if LCD_BACKLIGHT_TIMEOUT_MINS ui.refresh_backlight_timeout(); - #elif HAS_DISPLAY_SLEEP + #elif HAS_DISPLAY_SLEEP && DISABLED(TFT_COLOR_UI) ui.refresh_screen_timeout(); #endif } @@ -991,6 +995,11 @@ void MarlinSettings::postprocess() { EEPROM_WRITE(delta_diagonal_rod); // 1 float EEPROM_WRITE(delta_tower_angle_trim); // 3 floats EEPROM_WRITE(delta_diagonal_rod_trim); // 3 floats + #elif ENABLED(POLARGRAPH) + _FIELD_TEST(draw_area_min); + EEPROM_WRITE(draw_area_min); // 2 floats + EEPROM_WRITE(draw_area_max); // 2 floats + EEPROM_WRITE(polargraph_max_belt_len); // 1 float #endif } #endif @@ -1425,6 +1434,14 @@ void MarlinSettings::postprocess() { _FIELD_TEST(planner_skew_factor); EEPROM_WRITE(planner.skew_factor); + // + // POLARGRAPH + // + #if ENABLED(POLARGRAPH) + _FIELD_TEST(polargraph_max_belt_len); + EEPROM_WRITE(polargraph_max_belt_len); + #endif + // // Advanced Pause filament load & unload lengths // @@ -1932,6 +1949,11 @@ void MarlinSettings::postprocess() { EEPROM_READ(delta_diagonal_rod); // 1 float EEPROM_READ(delta_tower_angle_trim); // 3 floats EEPROM_READ(delta_diagonal_rod_trim); // 3 floats + #elif ENABLED(POLARGRAPH) + _FIELD_TEST(draw_area_min); + EEPROM_READ(draw_area_min); // 2 floats + EEPROM_READ(draw_area_max); // 2 floats + EEPROM_READ(polargraph_max_belt_len); // 1 float #endif } #endif @@ -2330,7 +2352,7 @@ void MarlinSettings::postprocess() { // Linear Advance // { - float extruder_advance_K[_MAX(EXTRUDERS, 1)]; + float extruder_advance_K[DISTINCT_E]; _FIELD_TEST(planner_extruder_advance_K); EEPROM_READ(extruder_advance_K); #if ENABLED(LIN_ADVANCE) @@ -2999,6 +3021,10 @@ void MarlinSettings::reset() { delta_diagonal_rod = DELTA_DIAGONAL_ROD; delta_tower_angle_trim = dta; delta_diagonal_rod_trim = ddr; + #elif ENABLED(POLARGRAPH) + draw_area_min.set(X_MIN_POS, Y_MIN_POS); + draw_area_max.set(X_MAX_POS, Y_MAX_POS); + polargraph_max_belt_len = POLARGRAPH_MAX_BELT_LEN; #endif #endif @@ -3170,7 +3196,7 @@ void MarlinSettings::reset() { #if LCD_BACKLIGHT_TIMEOUT_MINS ui.backlight_timeout_minutes = LCD_BACKLIGHT_TIMEOUT_MINS; #elif HAS_DISPLAY_SLEEP - ui.sleep_timeout_minutes = DISPLAY_SLEEP_MINUTES; + ui.sleep_timeout_minutes = TERN(TOUCH_SCREEN, TOUCH_IDLE_SLEEP_MINS, DISPLAY_SLEEP_MINUTES); #endif // @@ -3209,12 +3235,17 @@ void MarlinSettings::reset() { // // Linear Advance // - #if ENABLED(LIN_ADVANCE) - EXTRUDER_LOOP() { - planner.extruder_advance_K[e] = LIN_ADVANCE_K; - TERN_(EXTRA_LIN_ADVANCE_K, other_extruder_advance_K[e] = LIN_ADVANCE_K); - } + #if ENABLED(DISTINCT_E_FACTORS) + constexpr float linAdvanceK[] = ADVANCE_K; + EXTRUDER_LOOP() { + const float a = linAdvanceK[_MAX(e, COUNT(linAdvanceK) - 1)]; + planner.extruder_advance_K[e] = a; + TERN_(ADVANCE_K_EXTRA, other_extruder_advance_K[e] = a); + } + #else + planner.extruder_advance_K[0] = ADVANCE_K; + #endif #endif // @@ -3490,9 +3521,7 @@ void MarlinSettings::reset() { // // LCD Preheat Settings // - #if HAS_PREHEAT - gcode.M145_report(forReplay); - #endif + TERN_(HAS_PREHEAT, gcode.M145_report(forReplay)); // // PID diff --git a/Marlin/src/module/temperature.cpp b/Marlin/src/module/temperature.cpp index dd5712e1b0..349264606a 100644 --- a/Marlin/src/module/temperature.cpp +++ b/Marlin/src/module/temperature.cpp @@ -30,6 +30,7 @@ #include "../MarlinCore.h" #include "../HAL/shared/Delay.h" #include "../lcd/marlinui.h" +#include "../gcode/gcode.h" #include "temperature.h" #include "endstops.h" @@ -63,10 +64,6 @@ #include "../feature/host_actions.h" #endif -#if EITHER(HAS_TEMP_SENSOR, LASER_FEATURE) - #include "../gcode/gcode.h" -#endif - #if ENABLED(NOZZLE_PARK_FEATURE) #include "../libs/nozzle.h" #endif @@ -1848,6 +1845,14 @@ void Temperature::task() { emergency_parser.quickstop_by_M410 = false; // quickstop_stepper may call idle so clear this now! quickstop_stepper(); } + + #if ENABLED(SDSUPPORT) + if (emergency_parser.sd_abort_by_M524) { // abort SD print immediately + emergency_parser.sd_abort_by_M524 = false; + card.flag.abort_sd_printing = true; + gcode.process_subcommands_now(F("M524")); + } + #endif #endif if (!updateTemperaturesIfReady()) return; // Will also reset the watchdog if temperatures are ready @@ -2641,7 +2646,7 @@ void Temperature::init() { temp_range[NR].raw_max -= TEMPDIR(NR) * (OVERSAMPLENR); \ }while(0) - #define _MINMAX_TEST(N,M) (HOTENDS > N && TEMP_SENSOR_##N > 0 && TEMP_SENSOR_##N != 998 && TEMP_SENSOR_##N != 999 && defined(HEATER_##N##_##M##TEMP)) + #define _MINMAX_TEST(N,M) (HOTENDS > N && TEMP_SENSOR(N) > 0 && TEMP_SENSOR(N) != 998 && TEMP_SENSOR(N) != 999 && defined(HEATER_##N##_##M##TEMP)) #if _MINMAX_TEST(0, MIN) _TEMP_MIN_E(0); diff --git a/Marlin/src/module/thermistor/thermistor_1022.h b/Marlin/src/module/thermistor/thermistor_1022.h new file mode 100644 index 0000000000..1db928fbb8 --- /dev/null +++ b/Marlin/src/module/thermistor/thermistor_1022.h @@ -0,0 +1,45 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2022 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +#define REVERSE_TEMP_SENSOR_RANGE_1022 1 + +// Pt1000 with 1k0 pullup +constexpr temp_entry_t temptable_1022[] PROGMEM = { + PtLine( 0, 1000, 2200), + PtLine( 25, 1000, 2200), + PtLine( 50, 1000, 2200), + PtLine( 75, 1000, 2200), + PtLine(100, 1000, 2200), + PtLine(125, 1000, 2200), + PtLine(150, 1000, 2200), + PtLine(175, 1000, 2200), + PtLine(200, 1000, 2200), + PtLine(225, 1000, 2200), + PtLine(250, 1000, 2200), + PtLine(275, 1000, 2200), + PtLine(300, 1000, 2200), + PtLine(350, 1000, 2200), + PtLine(400, 1000, 2200), + PtLine(450, 1000, 2200), + PtLine(500, 1000, 2200) +}; diff --git a/Marlin/src/module/thermistor/thermistor_504.h b/Marlin/src/module/thermistor/thermistor_504.h index 0724e49b9d..751bea233e 100644 --- a/Marlin/src/module/thermistor/thermistor_504.h +++ b/Marlin/src/module/thermistor/thermistor_504.h @@ -1,9 +1,9 @@ /** * Marlin 3D Printer Firmware - * Copyright (C) 2022 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * Copyright (c) 2022 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. - * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by diff --git a/Marlin/src/module/thermistor/thermistor_505.h b/Marlin/src/module/thermistor/thermistor_505.h index 1377b43d24..12600f63ae 100644 --- a/Marlin/src/module/thermistor/thermistor_505.h +++ b/Marlin/src/module/thermistor/thermistor_505.h @@ -1,9 +1,9 @@ /** * Marlin 3D Printer Firmware - * Copyright (C) 2022 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * Copyright (c) 2022 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. - * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by diff --git a/Marlin/src/module/thermistor/thermistor_66.h b/Marlin/src/module/thermistor/thermistor_66.h index 07cb297679..7c2455b7c6 100644 --- a/Marlin/src/module/thermistor/thermistor_66.h +++ b/Marlin/src/module/thermistor/thermistor_66.h @@ -21,7 +21,7 @@ */ #pragma once -// R25 = 2.5 MOhm, beta25 = 4500 K, 4.7 kOhm pull-up, DyzeDesign 500 °C Thermistor +// R25 = 2.5 MOhm, beta25 = 4500 K, 4.7 kOhm pull-up, DyzeDesign / Trianglelab T-D500 500 °C Thermistor constexpr temp_entry_t temptable_66[] PROGMEM = { { OV( 17.5), 850 }, { OV( 17.9), 500 }, diff --git a/Marlin/src/module/thermistor/thermistors.h b/Marlin/src/module/thermistor/thermistors.h index a38b7f381f..c596d746f7 100644 --- a/Marlin/src/module/thermistor/thermistors.h +++ b/Marlin/src/module/thermistor/thermistors.h @@ -193,6 +193,9 @@ typedef struct { raw_adc_t value; celsius_t celsius; } temp_entry_t; #if ANY_THERMISTOR_IS(1010) // Pt1000 with 1k0 pullup #include "thermistor_1010.h" #endif +#if ANY_THERMISTOR_IS(1022) // Pt1000 with 2k2 pullup + #include "thermistor_1022.h" +#endif #if ANY_THERMISTOR_IS(1047) // Pt1000 with 4k7 pullup #include "thermistor_1047.h" #endif @@ -335,7 +338,7 @@ static_assert(255 > TEMPTABLE_0_LEN || 255 > TEMPTABLE_1_LEN || 255 > TEMPTABLE_ // For thermocouples the highest temperature results in the highest ADC value #define _TT_REV(N) REVERSE_TEMP_SENSOR_RANGE_##N -#define TT_REV(N) TERN0(TEMP_SENSOR_##N##_IS_THERMISTOR, DEFER4(_TT_REV)(TEMP_SENSOR_##N)) +#define TT_REV(N) TERN0(TEMP_SENSOR_##N##_IS_THERMISTOR, DEFER4(_TT_REV)(TEMP_SENSOR(N))) #define _TT_REVRAW(N) !TEMP_SENSOR_##N##_IS_THERMISTOR #define TT_REVRAW(N) (TT_REV(N) || _TT_REVRAW(N)) diff --git a/Marlin/src/module/tool_change.cpp b/Marlin/src/module/tool_change.cpp index 0ff0856ddd..4eb72a5b7d 100644 --- a/Marlin/src/module/tool_change.cpp +++ b/Marlin/src/module/tool_change.cpp @@ -440,6 +440,11 @@ void fast_line_to_current(const AxisEnum fr_axis) { _line_to_current(fr_axis, 0. } } + +#endif // TOOL_SENSOR + +#if ENABLED(SWITCHING_TOOLHEAD) + inline void switching_toolhead_lock(const bool locked) { #ifdef SWITCHING_TOOLHEAD_SERVO_ANGLES const uint16_t swt_angles[2] = SWITCHING_TOOLHEAD_SERVO_ANGLES; @@ -452,8 +457,6 @@ void fast_line_to_current(const AxisEnum fr_axis) { _line_to_current(fr_axis, 0. #endif } - #include - void swt_init() { switching_toolhead_lock(true); @@ -494,10 +497,6 @@ void fast_line_to_current(const AxisEnum fr_axis) { _line_to_current(fr_axis, 0. #endif // TOOL_SENSOR } -#endif // TOOL_SENSOR - -#if ENABLED(SWITCHING_TOOLHEAD) - inline void switching_toolhead_tool_change(const uint8_t new_tool, bool no_move/*=false*/) { if (no_move) return; diff --git a/Marlin/src/pins/linux/pins_RAMPS_LINUX.h b/Marlin/src/pins/linux/pins_RAMPS_LINUX.h index 9e2eedd68e..75d6b9d93e 100644 --- a/Marlin/src/pins/linux/pins_RAMPS_LINUX.h +++ b/Marlin/src/pins/linux/pins_RAMPS_LINUX.h @@ -450,6 +450,19 @@ #ifndef TOUCH_OFFSET_Y #define TOUCH_OFFSET_Y 1 #endif + #elif ENABLED(TFT_RES_1024x600) + #ifndef TOUCH_CALIBRATION_X + #define TOUCH_CALIBRATION_X 65533 + #endif + #ifndef TOUCH_CALIBRATION_Y + #define TOUCH_CALIBRATION_Y 38399 + #endif + #ifndef TOUCH_OFFSET_X + #define TOUCH_OFFSET_X 2 + #endif + #ifndef TOUCH_OFFSET_Y + #define TOUCH_OFFSET_Y 1 + #endif #endif #endif diff --git a/Marlin/src/pins/lpc1768/pins_BTT_SKR_V1_4.h b/Marlin/src/pins/lpc1768/pins_BTT_SKR_V1_4.h index 209529cbe1..aac8398081 100644 --- a/Marlin/src/pins/lpc1768/pins_BTT_SKR_V1_4.h +++ b/Marlin/src/pins/lpc1768/pins_BTT_SKR_V1_4.h @@ -43,6 +43,7 @@ #if NO_EEPROM_SELECTED //#define I2C_EEPROM // EEPROM on I2C-0 //#define SDCARD_EEPROM_EMULATION + //#undef NO_EEPROM_SELECTED #endif #if ENABLED(I2C_EEPROM) diff --git a/Marlin/src/pins/pins.h b/Marlin/src/pins/pins.h index 2bd5d61334..c623b4844d 100644 --- a/Marlin/src/pins/pins.h +++ b/Marlin/src/pins/pins.h @@ -591,6 +591,8 @@ #include "stm32f1/pins_CREALITY_V24S1_301.h" // STM32F1 env:STM32F103RE_creality env:STM32F103RE_creality_xfer env:STM32F103RC_creality env:STM32F103RC_creality_xfer env:STM32F103RE_creality_maple #elif MB(CREALITY_V25S1) #include "stm32f1/pins_CREALITY_V25S1.h" // STM32F1 env:STM32F103RE_creality_smartPro env:STM32F103RE_creality_smartPro_maple +#elif MB(CREALITY_V521) + #include "stm32f1/pins_CREALITY_V521.h" // STM32F103VE env:STM32F103VE_creality #elif MB(TRIGORILLA_PRO) #include "stm32f1/pins_TRIGORILLA_PRO.h" // STM32F1 env:trigorilla_pro env:trigorilla_pro_maple env:trigorilla_pro_disk #elif MB(FLY_MINI) @@ -707,6 +709,8 @@ #include "stm32f4/pins_OPULO_LUMEN_REV4.h" // STM32F4 env:Opulo_Lumen_REV4 #elif MB(FYSETC_SPIDER_KING407) #include "stm32f4/pins_FYSETC_SPIDER_KING407.h" // STM32F4 env:FYSETC_SPIDER_KING407 +#elif MB(MKS_SKIPR_V1) + #include "stm32f4/pins_MKS_SKIPR_V1_0.h" // STM32F4 env:mks_skipr_v1 env:mks_skipr_v1_nobootloader // // ARM Cortex M7 diff --git a/Marlin/src/pins/rambo/pins_EINSY_RAMBO.h b/Marlin/src/pins/rambo/pins_EINSY_RAMBO.h index 9150bf1365..c5d5fcef78 100644 --- a/Marlin/src/pins/rambo/pins_EINSY_RAMBO.h +++ b/Marlin/src/pins/rambo/pins_EINSY_RAMBO.h @@ -136,27 +136,56 @@ #ifndef FAN1_PIN #ifdef MK3_FAN_PINS - #define FAN1_PIN -1 + #define FAN1_PIN -1 #else - #define FAN1_PIN 6 + #define FAN1_PIN 6 #endif #endif +/** + * ------ ------ ------ + * 84 PH2 | 1 2 | PH6 9 50 MISO | 1 2 | SCK 52 62 PK0 | 1 2 | PJ5 76 + * 61 PF7 | 3 4 | PD5 82 72 PJ2 | 3 4 | SDSS 77 20 SDA | 3 4 | GND + * 59 PF5 | 5 6 PG4 70 14 TX3 | 5 6 MOSI 51 21 SCL | 5 6 RX2 16 + * 85 PH7 | 7 8 | PG3 71 15 RX3 | 7 8 | RESET GND | 7 8 | TX2 17 + * GND | 9 10 | 5V GND | 9 10 | PE3 5 5V | 9 10 | 5V + * ------ ------ ------ + * P1 P2 P3 + */ + +#define EXP1_01_PIN 84 +#define EXP1_02_PIN 9 +#define EXP1_03_PIN 61 +#define EXP1_04_PIN 82 +#define EXP1_05_PIN 59 +#define EXP1_06_PIN 70 +#define EXP1_07_PIN 85 +#define EXP1_08_PIN 71 + +#define EXP2_01_PIN 50 +#define EXP2_02_PIN 52 +#define EXP2_03_PIN 72 +#define EXP2_04_PIN 77 +#define EXP2_05_PIN 14 +#define EXP2_06_PIN 51 +#define EXP2_07_PIN 15 +#define EXP2_08_PIN -1 + // // Misc. Functions // -#define SDSS 77 +#define SDSS EXP2_04_PIN #define LED_PIN 13 #ifndef CASE_LIGHT_PIN - #define CASE_LIGHT_PIN 9 + #define CASE_LIGHT_PIN EXP1_02_PIN #endif // // M3/M4/M5 - Spindle/Laser Control // // use P1 connector for spindle pins -#define SPINDLE_LASER_PWM_PIN 9 // Hardware PWM +#define SPINDLE_LASER_PWM_PIN EXP1_02_PIN // Hardware PWM #define SPINDLE_LASER_ENA_PIN 18 // Pullup! #define SPINDLE_DIR_PIN 19 @@ -179,20 +208,20 @@ #if IS_ULTIPANEL || TOUCH_UI_ULTIPANEL #if ENABLED(CR10_STOCKDISPLAY) - #define LCD_PINS_RS 85 - #define LCD_PINS_ENABLE 71 - #define LCD_PINS_D4 70 - #define BTN_EN1 61 - #define BTN_EN2 59 + #define LCD_PINS_RS EXP1_07_PIN + #define LCD_PINS_ENABLE EXP1_08_PIN + #define LCD_PINS_D4 EXP1_06_PIN + #define BTN_EN1 EXP1_03_PIN + #define BTN_EN2 EXP1_05_PIN #else - #define LCD_PINS_RS 82 - #define LCD_PINS_ENABLE 61 - #define LCD_PINS_D4 59 - #define LCD_PINS_D5 70 - #define LCD_PINS_D6 85 - #define LCD_PINS_D7 71 - #define BTN_EN1 14 - #define BTN_EN2 72 + #define LCD_PINS_RS EXP1_04_PIN + #define LCD_PINS_ENABLE EXP1_03_PIN + #define LCD_PINS_D4 EXP1_05_PIN + #define LCD_PINS_D5 EXP1_06_PIN + #define LCD_PINS_D6 EXP1_07_PIN + #define LCD_PINS_D7 EXP1_08_PIN + #define BTN_EN1 EXP2_05_PIN + #define BTN_EN2 EXP2_03_PIN #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) #define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder @@ -200,9 +229,9 @@ #endif - #define BTN_ENC 9 // AUX-2 - #define BEEPER_PIN 84 // AUX-4 - #define SD_DETECT_PIN 15 + #define BTN_ENC EXP1_02_PIN // P1 + #define BEEPER_PIN EXP1_01_PIN // P1 + #define SD_DETECT_PIN EXP2_07_PIN #endif // IS_ULTIPANEL || TOUCH_UI_ULTIPANEL #endif // HAS_WIRED_LCD diff --git a/Marlin/src/pins/stm32f1/pins_CREALITY_V4.h b/Marlin/src/pins/stm32f1/pins_CREALITY_V4.h index 5a3e7337ad..11384799a3 100644 --- a/Marlin/src/pins/stm32f1/pins_CREALITY_V4.h +++ b/Marlin/src/pins/stm32f1/pins_CREALITY_V4.h @@ -161,91 +161,125 @@ #define SDIO_SUPPORT #define NO_SD_HOST_DRIVE // This board's SD is only seen by the printer +#if ANY(RET6_12864_LCD, HAS_DWIN_E3V2, IS_DWIN_MARLINUI) + + /** + * RET6 12864 LCD + * ------ + * PC6 | 1 2 | PB2 + * PB10 | 3 4 | PB11 + * PB14 5 6 | PB13 + * PB12 | 7 8 | PB15 + * GND | 9 10 | 5V + * ------ + */ + #define EXP3_01_PIN PC6 + #define EXP3_02_PIN PB2 + #define EXP3_03_PIN PB10 + #define EXP3_04_PIN PB11 + #define EXP3_05_PIN PB14 + #define EXP3_06_PIN PB13 + #define EXP3_07_PIN PB12 + #define EXP3_08_PIN PB15 + +#elif EITHER(VET6_12864_LCD, DWIN_VET6_CREALITY_LCD) + + /** + * VET6 12864 LCD + * ------ + * ? | 1 2 | PC5 + * PB10 | 3 4 | ? + * PA6 5 6 | PA5 + * PA4 | 7 8 | PA7 + * GND | 9 10 | 5V + * ------ + */ + #define EXP3_01_PIN -1 + #define EXP3_02_PIN PC5 + #define EXP3_03_PIN PB10 + #define EXP3_04_PIN -1 + #define EXP3_05_PIN PA6 + #define EXP3_06_PIN PA5 + #define EXP3_07_PIN PA4 + #define EXP3_08_PIN PA7 + +#elif EITHER(CR10_STOCKDISPLAY, FYSETC_MINI_12864_2_1) + #error "Define RET6_12864_LCD or VET6_12864_LCD to select pins for the LCD with the Creality V4 controller." +#endif + #if ENABLED(CR10_STOCKDISPLAY) - #if ENABLED(RET6_12864_LCD) + #define LCD_PINS_RS EXP3_07_PIN + #define LCD_PINS_ENABLE EXP3_08_PIN + #define LCD_PINS_D4 EXP3_06_PIN - /** - * RET6 12864 LCD - * ------ - * PC6 | 1 2 | PB2 - * PB10 | 3 4 | PE8 - * PB14 5 6 | PB13 - * PB12 | 7 8 | PB15 - * GND | 9 10 | 5V - * ------ - * EXP1 - */ - #define EXP1_01_PIN PC6 - #define EXP1_02_PIN PB2 - #define EXP1_03_PIN PB10 - #define EXP1_04_PIN PE8 - #define EXP1_05_PIN PB14 - #define EXP1_06_PIN PB13 - #define EXP1_07_PIN PB12 - #define EXP1_08_PIN PB15 + #define BTN_ENC EXP3_02_PIN + #define BTN_EN1 EXP3_03_PIN + #define BTN_EN2 EXP3_05_PIN - #ifndef HAS_PIN_27_BOARD - #define BEEPER_PIN EXP1_01_PIN - #endif - - #elif ENABLED(VET6_12864_LCD) - - /** - * VET6 12864 LCD - * ------ - * ? | 1 2 | PC5 - * PB10 | 3 4 | ? - * PA6 5 6 | PA5 - * PA4 | 7 8 | PA7 - * GND | 9 10 | 5V - * ------ - * EXP1 - */ - #define EXP1_01_PIN -1 - #define EXP1_02_PIN PC5 - #define EXP1_03_PIN PB10 - #define EXP1_04_PIN -1 - #define EXP1_05_PIN PA6 - #define EXP1_06_PIN PA5 - #define EXP1_07_PIN PA4 - #define EXP1_08_PIN PA7 - - #else - #error "Define RET6_12864_LCD or VET6_12864_LCD to select pins for CR10_STOCKDISPLAY with the Creality V4 controller." + #ifndef HAS_PIN_27_BOARD + #define BEEPER_PIN EXP3_01_PIN #endif - #define LCD_PINS_RS EXP1_07_PIN - #define LCD_PINS_ENABLE EXP1_08_PIN - #define LCD_PINS_D4 EXP1_06_PIN - - #define BTN_ENC EXP1_02_PIN - #define BTN_EN1 EXP1_03_PIN - #define BTN_EN2 EXP1_05_PIN - #elif ANY(HAS_DWIN_E3V2, IS_DWIN_MARLINUI, DWIN_VET6_CREALITY_LCD) - #if HAS_DWIN_E3V2 || IS_DWIN_MARLINUI - // RET6 DWIN ENCODER LCD - #define EXP1_05_PIN PB14 - #define EXP1_06_PIN PB13 - #define EXP1_07_PIN PB12 - #define EXP1_08_PIN PB15 - //#define LCD_LED_PIN PB2 - #else - // VET6 DWIN ENCODER LCD - #define EXP1_05_PIN PA6 - #define EXP1_06_PIN PA5 - #define EXP1_07_PIN PA4 - #define EXP1_08_PIN PA7 - #endif - - #define BTN_ENC EXP1_05_PIN - #define BTN_EN1 EXP1_08_PIN - #define BTN_EN2 EXP1_07_PIN + #define BTN_ENC EXP3_05_PIN + #define BTN_EN1 EXP3_08_PIN + #define BTN_EN2 EXP3_07_PIN #ifndef BEEPER_PIN - #define BEEPER_PIN EXP1_06_PIN + #define BEEPER_PIN EXP3_06_PIN #endif +#elif ENABLED(FYSETC_MINI_12864_2_1) + + #ifndef NO_CONTROLLER_CUSTOM_WIRING_WARNING + #error "CAUTION! FYSETC_MINI_12864_2_1 and clones require wiring modifications. See 'pins_CREALITY_V4.h' for details. Define NO_CONTROLLER_CUSTOM_WIRING_WARNING to suppress this warning." + #endif + + #if SD_CONNECTION_IS(LCD) + #error "The LCD SD Card is not connected with this configuration." + #endif + + /** + * + * Board (RET6 12864 LCD) Display + * ------ ------ + * (EN1) PC6 | 1 2 | PB2 (BTN_ENC) 5V |10 9 | GND + * (LCD_CS) PB10 | 3 4 | PB11 (LCD RESET) -- | 8 7 | -- + * (LCD_A0) PB14 5 6 | PB13 (EN2) (DIN) | 6 5 (LCD RESET) + * (LCD_SCK)PB12 | 7 8 | PB15 (MOSI) (LCD_A0) | 4 3 | (LCD_CS) + * GND | 9 10 | 5V (BTN_ENC) | 2 1 | -- + * ------ ------ + * EXP1 EXP1 + * + * ------ + * ----- -- |10 9 | -- + * | 1 | VCC (RESET) | 8 7 | -- + * | 2 | PA13 (DIN) (MOSI) | 6 5 (EN2) + * | 3 | PA14 -- | 4 3 | (EN1) + * | 4 | GND (LCD_SCK)| 2 1 | -- + * ----- ------ + * Debug port EXP2 + * + * Needs custom cable. Connect EN2-EN2, LCD_CS-LCD_CS and so on. + * Debug port is just above EXP1. You need to add pins. + * + */ + + #define BTN_ENC EXP3_02_PIN + #define BTN_EN1 EXP3_01_PIN + #define BTN_EN2 EXP3_06_PIN + #define BEEPER_PIN -1 + + #define DOGLCD_CS EXP3_03_PIN + #define DOGLCD_A0 EXP3_05_PIN + #define DOGLCD_SCK EXP3_07_PIN + #define DOGLCD_MOSI EXP3_08_PIN + #define LCD_RESET_PIN EXP3_04_PIN + + #define FORCE_SOFT_SPI + #define LCD_BACKLIGHT_PIN -1 + #define NEOPIXEL_PIN PA13 + #endif diff --git a/Marlin/src/pins/stm32f1/pins_CREALITY_V4210.h b/Marlin/src/pins/stm32f1/pins_CREALITY_V4210.h index 86ede843be..f3b7e4f308 100644 --- a/Marlin/src/pins/stm32f1/pins_CREALITY_V4210.h +++ b/Marlin/src/pins/stm32f1/pins_CREALITY_V4210.h @@ -1,9 +1,9 @@ /** * Marlin 3D Printer Firmware - * Copyright (C) 2021 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * Copyright (c) 2021 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. - * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -22,7 +22,7 @@ #pragma once /** - * CREALITY 4.2.10 (STM32F103RE / STM32F103RC) board pin assignments + * Creality 4.2.10 (STM32F103RE / STM32F103RC) board pin assignments */ #include "env_validate.h" @@ -143,85 +143,75 @@ #define SDIO_SUPPORT #define NO_SD_HOST_DRIVE // This board's SD is only seen by the printer +#if ANY(RET6_12864_LCD, HAS_DWIN_E3V2, IS_DWIN_MARLINUI) + + /** + * RET6 12864 LCD + * ------ + * PC6 | 1 2 | PB2 + * PB10 | 3 4 | PE8 + * PB14 5 6 | PB13 + * PB12 | 7 8 | PB15 + * GND | 9 10 | 5V + * ------ + */ + #define EXP3_01_PIN PC6 + #define EXP3_02_PIN PB2 + #define EXP3_03_PIN PB10 + #define EXP3_04_PIN PE8 + #define EXP3_05_PIN PB14 + #define EXP3_06_PIN PB13 + #define EXP3_07_PIN PB12 + #define EXP3_08_PIN PB15 + +#elif EITHER(VET6_12864_LCD, DWIN_VET6_CREALITY_LCD) + + /** + * VET6 12864 LCD + * ------ + * ? | 1 2 | PC5 + * PB10 | 3 4 | ? + * PA6 5 6 | PA5 + * PA4 | 7 8 | PA7 + * GND | 9 10 | 5V + * ------ + */ + #define EXP3_01_PIN -1 + #define EXP3_02_PIN PC5 + #define EXP3_03_PIN PB10 + #define EXP3_04_PIN -1 + #define EXP3_05_PIN PA6 + #define EXP3_06_PIN PA5 + #define EXP3_07_PIN PA4 + #define EXP3_08_PIN PA7 + +#endif + #if ENABLED(CR10_STOCKDISPLAY) - - #if ENABLED(RET6_12864_LCD) - - /** - * RET6 12864 LCD - * ------ - * PC6 | 1 2 | PB2 - * PB10 | 3 4 | PE8 - * PB14 5 6 | PB13 - * PB12 | 7 8 | PB15 - * GND | 9 10 | 5V - * ------ - * EXP1 - */ - #define EXP1_01_PIN PC6 - #define EXP1_02_PIN PB2 - #define EXP1_03_PIN PB10 - #define EXP1_04_PIN PE8 - #define EXP1_05_PIN PB14 - #define EXP1_06_PIN PB13 - #define EXP1_07_PIN PB12 - #define EXP1_08_PIN PB15 - - #define BEEPER_PIN EXP1_01_PIN - - #elif ENABLED(VET6_12864_LCD) - - /** - * VET6 12864 LCD - * ------ - * ? | 1 2 | PC5 - * PB10 | 3 4 | ? - * PA6 5 6 | PA5 - * PA4 | 7 8 | PA7 - * GND | 9 10 | 5V - * ------ - * EXP1 - */ - #define EXP1_01_PIN -1 - #define EXP1_02_PIN PC5 - #define EXP1_03_PIN PB10 - #define EXP1_04_PIN -1 - #define EXP1_05_PIN PA6 - #define EXP1_06_PIN PA5 - #define EXP1_07_PIN PA4 - #define EXP1_08_PIN PA7 - - #else + #if NONE(RET6_12864_LCD, VET6_12864_LCD) #error "Define RET6_12864_LCD or VET6_12864_LCD to select pins for CR10_STOCKDISPLAY with the Creality V4 controller." #endif - #define LCD_PINS_RS EXP1_07_PIN - #define LCD_PINS_ENABLE EXP1_08_PIN - #define LCD_PINS_D4 EXP1_06_PIN + #define LCD_PINS_RS EXP3_07_PIN + #define LCD_PINS_ENABLE EXP3_08_PIN + #define LCD_PINS_D4 EXP3_06_PIN - #define BTN_ENC EXP1_02_PIN - #define BTN_EN1 EXP1_03_PIN - #define BTN_EN2 EXP1_05_PIN + #define BTN_ENC EXP3_02_PIN + #define BTN_EN1 EXP3_03_PIN + #define BTN_EN2 EXP3_05_PIN -#elif HAS_DWIN_E3V2 || IS_DWIN_MARLINUI + #define BEEPER_PIN EXP3_01_PIN - // RET6 DWIN ENCODER LCD - #define BTN_ENC PB14 - #define BTN_EN1 PB15 - #define BTN_EN2 PB12 +#elif ANY(DWIN_VET6_CREALITY_LCD, HAS_DWIN_E3V2, IS_DWIN_MARLINUI) - //#define LCD_LED_PIN PB2 + // RET6 / VET6 DWIN ENCODER LCD + #define BTN_ENC EXP3_05_PIN + #define BTN_EN1 EXP3_08_PIN + #define BTN_EN2 EXP3_07_PIN + + //#define LCD_LED_PIN EXP3_02_PIN #ifndef BEEPER_PIN - #define BEEPER_PIN PB13 + #define BEEPER_PIN EXP3_06_PIN #endif -#elif ENABLED(DWIN_VET6_CREALITY_LCD) - - // VET6 DWIN ENCODER LCD - #define BTN_ENC PA6 - #define BTN_EN1 PA7 - #define BTN_EN2 PA4 - - #define BEEPER_PIN PA5 - #endif diff --git a/Marlin/src/pins/stm32f1/pins_CREALITY_V422.h b/Marlin/src/pins/stm32f1/pins_CREALITY_V422.h index c6b6e84bfa..9e26b37de0 100644 --- a/Marlin/src/pins/stm32f1/pins_CREALITY_V422.h +++ b/Marlin/src/pins/stm32f1/pins_CREALITY_V422.h @@ -28,8 +28,6 @@ #define BOARD_INFO_NAME "Creality v4.2.2" #define DEFAULT_MACHINE_NAME "Creality3D" -#ifndef EMIT_CREALITY_422_WARNING - #define EMIT_CREALITY_422_WARNING -#endif +#define EMIT_CREALITY_422_WARNING #include "pins_CREALITY_V4.h" diff --git a/Marlin/src/pins/stm32f1/pins_CREALITY_V425.h b/Marlin/src/pins/stm32f1/pins_CREALITY_V425.h index 46f437ecaf..1c62d19a99 100644 --- a/Marlin/src/pins/stm32f1/pins_CREALITY_V425.h +++ b/Marlin/src/pins/stm32f1/pins_CREALITY_V425.h @@ -1,9 +1,9 @@ /** * Marlin 3D Printer Firmware - * Copyright (C) 2022 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * Copyright (c) 2022 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. - * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by diff --git a/Marlin/src/pins/stm32f1/pins_CREALITY_V521.h b/Marlin/src/pins/stm32f1/pins_CREALITY_V521.h new file mode 100644 index 0000000000..d3d3685531 --- /dev/null +++ b/Marlin/src/pins/stm32f1/pins_CREALITY_V521.h @@ -0,0 +1,226 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2022 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +/** + * Creality 5.2.1 (STM32F103RE) board pin assignments + */ + +#include "env_validate.h" + +#if HOTENDS > 2 || E_STEPPERS > 2 + #error "Creality v5.2.1 supports up to 2 hotends / E steppers." +#endif + +#ifndef BOARD_INFO_NAME + #define BOARD_INFO_NAME "Creality V521" +#endif +#ifndef DEFAULT_MACHINE_NAME + #define DEFAULT_MACHINE_NAME "Creality V5.2.1" +#endif + +// +// EEPROM +// +#if NO_EEPROM_SELECTED + // FLASH + //#define FLASH_EEPROM_EMULATION + + // I2C + #define IIC_BL24CXX_EEPROM // EEPROM on I2C-0 used only for display settings + #if ENABLED(IIC_BL24CXX_EEPROM) + #define IIC_EEPROM_SDA PC2 + #define IIC_EEPROM_SCL PC3 + #define MARLIN_EEPROM_SIZE 0x800 // 2K (24C16) + #else + #define SDCARD_EEPROM_EMULATION // SD EEPROM until all EEPROM is BL24CXX + #define MARLIN_EEPROM_SIZE 0x800 // 2K + #endif + + #undef NO_EEPROM_SELECTED +#endif + +// +// Servos +// +#define SERVO0_PIN PD13 // BLTouch OUT + +// +// Limit Switches +// +#define X_STOP_PIN PD10 // X +#define X2_STOP_PIN PE15 // X2 +#define Y_STOP_PIN PE0 // Y +#define Z_STOP_PIN PE1 // Z +#define Z2_STOP_PIN PE2 // Z2 + +#ifndef Z_MIN_PROBE_PIN + #define Z_MIN_PROBE_PIN PD12 // BLTouch IN +#endif + +// +// Filament Runout Sensor +// +#define FIL_RUNOUT_PIN PE5 // "Pulled-high" +#define FIL_RUNOUT2_PIN PE6 // "Pulled-high" + +// +// Steppers +// +#define X_ENABLE_PIN PC7 +#define X_STEP_PIN PD15 +#define X_DIR_PIN PD14 + +#define Y_ENABLE_PIN PB9 +#define Y_STEP_PIN PB7 +#define Y_DIR_PIN PB6 + +#define Z_ENABLE_PIN PB5 +#define Z_STEP_PIN PB3 +#define Z_DIR_PIN PD7 + +#define E0_ENABLE_PIN PD4 +#define E0_STEP_PIN PD1 +#define E0_DIR_PIN PD0 + +#define E1_ENABLE_PIN PE7 +#define E1_STEP_PIN PB1 +#define E1_DIR_PIN PB0 + +#define X2_ENABLE_PIN PE11 +#define X2_STEP_PIN PE9 +#define X2_DIR_PIN PE8 + +#define Z2_ENABLE_PIN PC5 +#define Z2_STEP_PIN PA7 +#define Z2_DIR_PIN PA6 + +// +// Release PB4 (Y_ENABLE_PIN) from JTAG NRST role +// +#define DISABLE_JTAG + +// +// Temperature Sensors +// +#define TEMP_0_PIN PA4 // TH0 +#define TEMP_1_PIN PA5 // TH1 +#define TEMP_BED_PIN PA3 // TB1 + +// +// Heaters / Fans +// +#define HEATER_0_PIN PA1 // HEATER0 +#define HEATER_1_PIN PA0 // HEATER1 +#define HEATER_BED_PIN PA2 // HOT BED + +#define FAN_PIN PB14 // FAN +#define FAN1_PIN PB12 // FAN +#define FAN_SOFT_PWM + +// +// SD Card +// +#define SD_DETECT_PIN PA8 +#define SDCARD_CONNECTION ONBOARD +#define ONBOARD_SPI_DEVICE 1 +#define ONBOARD_SD_CS_PIN PC11 // SDSS +#define SDIO_SUPPORT +#define NO_SD_HOST_DRIVE // This board's SD is only seen by the printer + +#if ANY(RET6_12864_LCD, HAS_DWIN_E3V2, IS_DWIN_MARLINUI) + + /** + * RET6 12864 LCD + * ------ + * PC6 | 1 2 | PB2 + * PB10 | 3 4 | PE8 + * PB14 5 6 | PB13 + * PB12 | 7 8 | PB15 + * GND | 9 10 | 5V + * ------ + */ + #define EXP3_01_PIN PC6 + #define EXP3_02_PIN PB2 + #define EXP3_03_PIN PB10 + #define EXP3_04_PIN PE8 + #define EXP3_05_PIN PB14 + #define EXP3_06_PIN PB13 + #define EXP3_07_PIN PB12 + #define EXP3_08_PIN PB15 + +#elif EITHER(VET6_12864_LCD, DWIN_VET6_CREALITY_LCD) + + /** + * VET6 12864 LCD + * ------ + * ? | 1 2 | PC5 + * PB10 | 3 4 | ? + * PA6 5 6 | PA5 + * PA4 | 7 8 | PA7 + * GND | 9 10 | 5V + * ------ + */ + #define EXP3_01_PIN -1 + #define EXP3_02_PIN PC5 + #define EXP3_03_PIN PB10 + #define EXP3_04_PIN -1 + #define EXP3_05_PIN PA6 + #define EXP3_06_PIN PA5 + #define EXP3_07_PIN PA4 + #define EXP3_08_PIN PA7 + +#endif + +#if ENABLED(CR10_STOCKDISPLAY) + #if NONE(RET6_12864_LCD, VET6_12864_LCD) + #error "Define RET6_12864_LCD or VET6_12864_LCD to select pins for CR10_STOCKDISPLAY with the Creality V4 controller." + #endif + + #define LCD_PINS_RS EXP3_07_PIN + #define LCD_PINS_ENABLE EXP3_08_PIN + #define LCD_PINS_D4 EXP3_06_PIN + + #define BTN_ENC EXP3_02_PIN + #define BTN_EN1 EXP3_03_PIN + #define BTN_EN2 EXP3_05_PIN + + #define BEEPER_PIN EXP3_01_PIN + +#elif ANY(DWIN_VET6_CREALITY_LCD, HAS_DWIN_E3V2, IS_DWIN_MARLINUI) + + // RET6 / VET6 DWIN ENCODER LCD + #define BTN_ENC EXP3_05_PIN + #define BTN_EN1 EXP3_08_PIN + #define BTN_EN2 EXP3_07_PIN + + //#define LCD_LED_PIN EXP3_02_PIN + #ifndef BEEPER_PIN + #define BEEPER_PIN EXP3_06_PIN + #endif + +#endif + +// DGUS LCDs +#if HAS_DGUS_LCD + #define LCD_SERIAL_PORT 3 +#endif diff --git a/Marlin/src/pins/stm32f4/pins_MKS_SKIPR_V1_0.h b/Marlin/src/pins/stm32f4/pins_MKS_SKIPR_V1_0.h new file mode 100644 index 0000000000..046fbb95bf --- /dev/null +++ b/Marlin/src/pins/stm32f4/pins_MKS_SKIPR_V1_0.h @@ -0,0 +1,381 @@ +/** + * Marlin 3D Printer Firmware + * Copyright (c) 2022 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] + * + * Based on Sprinter and grbl. + * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm + * + * This program is free software: you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation, either version 3 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + * + */ +#pragma once + +#include "env_validate.h" + +#if HOTENDS > 4 || E_STEPPERS > 4 + #error "MKS SKIPR supports up to 4 hotends / E steppers." +#endif + +#define BOARD_INFO_NAME "MKS SKIPR V1.0" + +// Valid SERIAL_PORT values: -1 (USB-C), 1 (direct to RK3328), 3 (USART3 header) + +#define USES_DIAG_JUMPERS + +// Onboard I2C EEPROM +#define I2C_EEPROM +#define MARLIN_EEPROM_SIZE 0x1000 // 4KB (AT24C32) +#define I2C_SCL_PIN PB8 +#define I2C_SDA_PIN PB9 + +// +// Servos +// +#define SERVO0_PIN PA8 + +// +// Trinamic Stallguard pins // Connector labels +#define X_DIAG_PIN PA14 // X- +#define Y_DIAG_PIN PA15 // Y- +#define Z_DIAG_PIN PB15 // Z- +#define E0_DIAG_PIN PA13 // MT-DET +#define E1_DIAG_PIN PC5 // NEOPIXEL +#define E2_DIAG_PIN PB14 // Z+ + +// +// Check for additional used endstop pins +// +#if HAS_EXTRA_ENDSTOPS + #define _ENDSTOP_IS_ANY(ES) X2_USE_ENDSTOP == ES || Y2_USE_ENDSTOP == ES || Z2_USE_ENDSTOP == ES || Z3_USE_ENDSTOP == ES || Z4_USE_ENDSTOP == ES + #if _ENDSTOP_IS_ANY(_XMIN_) || _ENDSTOP_IS_ANY(_XMAX_) + #define NEEDS_X_MINMAX 1 + #endif + #if _ENDSTOP_IS_ANY(_YMIN_) || _ENDSTOP_IS_ANY(_YMAX_) + #define NEEDS_Y_MINMAX 1 + #endif + #if _ENDSTOP_IS_ANY(_ZMIN_) || _ENDSTOP_IS_ANY(_ZMAX_) + #define NEEDS_Z_MINMAX 1 + #endif + #undef _ENDSTOP_IS_ANY +#endif + +// +// Limit Switches +// +#ifdef X_STALL_SENSITIVITY + #define X_STOP_PIN X_DIAG_PIN // X- +#elif EITHER(DUAL_X_CARRIAGE, NEEDS_X_MINMAX) + #ifndef X_MIN_PIN + #define X_MIN_PIN X_DIAG_PIN // X- + #endif + #ifndef X_MAX_PIN + #define X_MAX_PIN E0_DIAG_PIN // MT-DET + #endif +#else + #define X_STOP_PIN X_DIAG_PIN // X- +#endif + +#ifdef Y_STALL_SENSITIVITY + #define Y_STOP_PIN Y_DIAG_PIN // Y- +#elif NEEDS_Y_MINMAX + #ifndef Y_MIN_PIN + #define Y_MIN_PIN Y_DIAG_PIN // Y- + #endif + #ifndef Y_MAX_PIN + #define Y_MAX_PIN E1_DIAG_PIN // NEOPIXEL + #endif +#else + #define Y_STOP_PIN Y_DIAG_PIN // Y- +#endif + +#ifdef Z_STALL_SENSITIVITY + #define Z_STOP_PIN Z_DIAG_PIN // Z- +#elif NEEDS_Z_MINMAX + #ifndef Z_MIN_PIN + #define Z_MIN_PIN Z_DIAG_PIN // Z- + #endif + #ifndef Z_MAX_PIN + #define Z_MAX_PIN E2_DIAG_PIN // Z+ + #endif +#else + #define Z_STOP_PIN Z_DIAG_PIN // Z- +#endif + +#if DISABLED(Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN) || ENABLED(USE_PROBE_FOR_Z_HOMING) + #ifndef Z_MIN_PROBE + #define Z_MIN_PROBE_PIN E2_DIAG_PIN // defaults to 'Z+' connector + #endif +#endif + +#undef NEEDS_X_MINMAX +#undef NEEDS_Y_MINMAX +#undef NEEDS_Z_MINMAX + +// +// Steppers +// +#define X_STEP_PIN PC14 +#define X_DIR_PIN PC13 +#define X_ENABLE_PIN PC15 +#ifndef X_CS_PIN + #define X_CS_PIN PE6 +#endif + +#define Y_STEP_PIN PE5 +#define Y_DIR_PIN PE4 +#define Y_ENABLE_PIN PD14 +#ifndef Y_CS_PIN + #define Y_CS_PIN PE3 +#endif + +#define Z_STEP_PIN PE1 // "Z1" +#define Z_DIR_PIN PE0 +#define Z_ENABLE_PIN PE2 +#ifndef Z_CS_PIN + #define Z_CS_PIN PB7 +#endif + +#define E0_STEP_PIN PB5 +#define E0_DIR_PIN PB4 +#define E0_ENABLE_PIN PB6 +#ifndef E0_CS_PIN + #define E0_CS_PIN PB3 +#endif + +#define E1_STEP_PIN PD6 // "Z2" +#define E1_DIR_PIN PD5 +#define E1_ENABLE_PIN PD7 +#ifndef E1_CS_PIN + #define E1_CS_PIN PD4 +#endif + +#define E2_STEP_PIN PD2 // "Z3" +#define E2_DIR_PIN PD1 +#define E2_ENABLE_PIN PD3 +#ifndef E2_CS_PIN + #define E2_CS_PIN PD0 +#endif + +#define E3_STEP_PIN PC7 // "Z4" +#define E3_DIR_PIN PC6 +#define E3_ENABLE_PIN PC8 +#ifndef E3_CS_PIN + #define E3_CS_PIN PD15 +#endif + +// +// Temperature Sensors +// +#define TEMP_BED_PIN PC0 // TB +#define TEMP_0_PIN PC1 // TH0 +#define TEMP_1_PIN PC2 // TH1 +#define TEMP_2_PIN PC3 // TH2 + +// +// Heaters / Fans +// +#define HEATER_BED_PIN PD12 // Hotbed +#define HEATER_0_PIN PB1 // Heater0 +#define HEATER_1_PIN PB0 // Heater1 +#define HEATER_2_PIN PA3 // Heater2 + +#define FAN_PIN PA2 // Fan0 +#define FAN1_PIN PA1 // Fan1 +#define FAN2_PIN PA0 // Fan2 + +// +// Software SPI pins for TMC2130 stepper drivers +// This board doesn't support hardware SPI there +// +#if HAS_TMC_SPI + #define TMC_USE_SW_SPI + #define TMC_SW_MOSI PE14 + #define TMC_SW_MISO PE13 + #define TMC_SW_SCK PE12 +#endif + +// +// TMC2208/TMC2209 stepper drivers +// This board is routed for one-wire software serial +// +#if HAS_TMC_UART + #define X_SERIAL_TX_PIN PE6 + #define X_SERIAL_RX_PIN X_SERIAL_TX_PIN + + #define Y_SERIAL_TX_PIN PE3 + #define Y_SERIAL_RX_PIN Y_SERIAL_TX_PIN + + #define Z_SERIAL_TX_PIN PB7 + #define Z_SERIAL_RX_PIN Z_SERIAL_TX_PIN + + #define E0_SERIAL_TX_PIN PB3 + #define E0_SERIAL_RX_PIN E0_SERIAL_TX_PIN + + #define E1_SERIAL_TX_PIN PD4 + #define E1_SERIAL_RX_PIN E1_SERIAL_TX_PIN + + #define E2_SERIAL_TX_PIN PD0 + #define E2_SERIAL_RX_PIN E2_SERIAL_TX_PIN + + #define E3_SERIAL_TX_PIN PD15 + #define E3_SERIAL_RX_PIN E3_SERIAL_TX_PIN + + // Reduce baud rate to improve software serial reliability + #define TMC_BAUD_RATE 19200 +#endif + +/** ------ ------ + * (BEEPER) PB2 | 1 2 | PE10 (BTN_ENC) (MISO) PA6 | 1 2 | PA5 (SCK) + * (LCD_EN) PE11 | 3 4 | PD10 (LCD_RS) (BTN_EN1) PE9 | 3 4 | PA4 (SD_SS) + * (LCD_D4) PD9 | 5 6 PD8 (LCD_D5) (BTN_EN2) PE8 | 5 6 PA7 (MOSI) + * (LCD_D6) PE15 | 7 8 | PE7 (LCD_D7) (SD_DETECT) PD13 | 7 8 | RESET + * GND | 9 10 | 5V GND | 9 10 | -- + * ------ ------ + * EXP1 EXP2 + */ +#define EXP1_01_PIN PB2 +#define EXP1_02_PIN PE10 +#define EXP1_03_PIN PE11 +#define EXP1_04_PIN PD10 +#define EXP1_05_PIN PD9 +#define EXP1_06_PIN PD8 +#define EXP1_07_PIN PE15 +#define EXP1_08_PIN PE7 + +#define EXP2_01_PIN PA6 +#define EXP2_02_PIN PA5 +#define EXP2_03_PIN PE9 +#define EXP2_04_PIN PA4 +#define EXP2_05_PIN PE8 +#define EXP2_06_PIN PA7 +#define EXP2_07_PIN PD13 +#define EXP2_08_PIN -1 // connected to MCU reset + +// +// SD Support +// Onboard SD card use hardware SPI3 (defined in variant), LCD SD card use hardware SPI1 +// +#if ENABLED(SDSUPPORT) + #ifndef SDCARD_CONNECTION + #define SDCARD_CONNECTION LCD + #endif + #if SD_CONNECTION_IS(ONBOARD) + //#define SOFTWARE_SPI + //#define SD_SPI_SPEED SPI_HALF_SPEED + #undef SD_DETECT_STATE + #define SD_DETECT_STATE LOW + #define SD_DETECT_PIN PC4 + #elif SD_CONNECTION_IS(LCD) + //#define SOFTWARE_SPI + //#define SD_SPI_SPEED SPI_QUARTER_SPEED + #define SD_SS_PIN EXP2_04_PIN + #define SD_SCK_PIN EXP2_02_PIN + #define SD_MISO_PIN EXP2_01_PIN + #define SD_MOSI_PIN EXP2_06_PIN + #define SD_DETECT_PIN EXP2_07_PIN + #elif SD_CONNECTION_IS(CUSTOM_CABLE) + #error "CUSTOM_CABLE is not a supported SDCARD_CONNECTION for this board" + #endif + #define SDSS SD_SS_PIN +#endif + +// +// LCDs and Controllers +// +#if IS_TFTGLCD_PANEL + + #if ENABLED(TFTGLCD_PANEL_SPI) + #define TFTGLCD_CS EXP2_03_PIN + #endif + +#elif HAS_WIRED_LCD + + #define BEEPER_PIN EXP1_01_PIN + #define BTN_ENC EXP1_02_PIN + + #if ENABLED(CR10_STOCKDISPLAY) + + #define LCD_PINS_RS EXP1_07_PIN + + #define BTN_EN1 EXP1_03_PIN + #define BTN_EN2 EXP1_05_PIN + + #define LCD_PINS_ENABLE EXP1_08_PIN + #define LCD_PINS_D4 EXP1_06_PIN + + #else + + #define LCD_PINS_RS EXP1_04_PIN + + #define BTN_EN1 EXP2_03_PIN + #define BTN_EN2 EXP2_05_PIN + + #define LCD_PINS_ENABLE EXP1_03_PIN + #define LCD_PINS_D4 EXP1_05_PIN + + #if ENABLED(FYSETC_MINI_12864) + #define DOGLCD_CS EXP1_03_PIN + #define DOGLCD_A0 EXP1_04_PIN + //#define LCD_BACKLIGHT_PIN -1 + #define LCD_RESET_PIN EXP1_05_PIN // Must be high or open for LCD to operate normally. + #if EITHER(FYSETC_MINI_12864_1_2, FYSETC_MINI_12864_2_0) + #ifndef RGB_LED_R_PIN + #define RGB_LED_R_PIN EXP1_06_PIN + #endif + #ifndef RGB_LED_G_PIN + #define RGB_LED_G_PIN EXP1_07_PIN + #endif + #ifndef RGB_LED_B_PIN + #define RGB_LED_B_PIN EXP1_08_PIN + #endif + #elif ENABLED(FYSETC_MINI_12864_2_1) + #define NEOPIXEL_PIN EXP1_06_PIN + #endif + #endif // !FYSETC_MINI_12864 + + #if IS_ULTIPANEL + #define LCD_PINS_D5 EXP1_06_PIN + #define LCD_PINS_D6 EXP1_07_PIN + #define LCD_PINS_D7 EXP1_08_PIN + #if ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) + #define BTN_ENC_EN LCD_PINS_D7 // Detect the presence of the encoder + #endif + #endif + + #endif +#endif // HAS_WIRED_LCD + +// Alter timing for graphical display +#if IS_U8GLIB_ST7920 + #define BOARD_ST7920_DELAY_1 120 + #define BOARD_ST7920_DELAY_2 80 + #define BOARD_ST7920_DELAY_3 580 +#endif + +// +// NeoPixel LED +// +#ifndef NEOPIXEL_PIN + #define NEOPIXEL_PIN PC5 +#endif + +// +// MAX31865 +// +#if HAS_MAX31865 + #define TEMP_0_CS_PIN PD11 + #define TEMP_0_SCK_PIN PE12 + #define TEMP_0_MISO_PIN PE13 + #define TEMP_0_MOSI_PIN PE14 +#endif diff --git a/Marlin/src/pins/stm32f4/pins_OPULO_LUMEN_REV3.h b/Marlin/src/pins/stm32f4/pins_OPULO_LUMEN_REV3.h index 36dde88105..06bf09402c 100644 --- a/Marlin/src/pins/stm32f4/pins_OPULO_LUMEN_REV3.h +++ b/Marlin/src/pins/stm32f4/pins_OPULO_LUMEN_REV3.h @@ -44,6 +44,9 @@ // I2C MCP3426 (16-Bit, 240SPS, dual-channel ADC) #define HAS_MCP3426_ADC +#ifdef STM32F4 + #define HAS_STM32_UID +#endif // // Servos diff --git a/Marlin/src/pins/stm32g0/pins_BTT_SKR_MINI_E3_V3_0.h b/Marlin/src/pins/stm32g0/pins_BTT_SKR_MINI_E3_V3_0.h index 956cb71f83..f931d9924a 100644 --- a/Marlin/src/pins/stm32g0/pins_BTT_SKR_MINI_E3_V3_0.h +++ b/Marlin/src/pins/stm32g0/pins_BTT_SKR_MINI_E3_V3_0.h @@ -311,7 +311,7 @@ #elif ENABLED(FYSETC_MINI_12864_2_1) #ifndef NO_CONTROLLER_CUSTOM_WIRING_WARNING - #error "CAUTION! FYSETC_MINI_12864_2_1 and clones require wiring modifications. See 'pins_BTT_SKR_MINI_E3_V3_0.h' for details. Define NO_CONTROLLER_CUSTOM_WIRING_WARNING to suppress this warning" + #error "CAUTION! FYSETC_MINI_12864_2_1 and clones require wiring modifications. See 'pins_BTT_SKR_MINI_E3_V3_0.h' for details. Define NO_CONTROLLER_CUSTOM_WIRING_WARNING to suppress this warning." #endif /** diff --git a/buildroot/share/PlatformIO/boards/marlin_MKS_SKIPR_V1.json b/buildroot/share/PlatformIO/boards/marlin_MKS_SKIPR_V1.json new file mode 100644 index 0000000000..7ca62db005 --- /dev/null +++ b/buildroot/share/PlatformIO/boards/marlin_MKS_SKIPR_V1.json @@ -0,0 +1,55 @@ +{ + "build": { + "core": "stm32", + "cpu": "cortex-m4", + "extra_flags": "-DSTM32F4 -DSTM32F407xx", + "f_cpu": "168000000L", + "offset": "0xC000", + "hwids": [ + [ + "0x1EAF", + "0x0003" + ], + [ + "0x0483", + "0x3748" + ] + ], + "mcu": "stm32f407vet6", + "product_line": "STM32F407xx", + "variant": "MARLIN_MKS_SKIPR_V1" + }, + "debug": { + "default_tools": [ + "stlink" + ], + "jlink_device": "STM32F407VE", + "openocd_extra_args": [ + "-c", + "reset_config none" + ], + "openocd_target": "stm32f4x", + "svd_path": "STM32F40x.svd" + }, + "frameworks": [ + "arduino" + ], + "name": "STM32F407VE (128k RAM, 64k CCM RAM, 512k Flash", + "upload": { + "disable_flushing": false, + "maximum_ram_size": 131072, + "maximum_size": 524288, + "protocol": "stlink", + "protocols": [ + "stlink", + "dfu", + "jlink" + ], + "offset_address": "0x0800C000", + "require_upload_port": false, + "use_1200bps_touch": false, + "wait_for_upload_port": false + }, + "url": "https://www.st.com/en/microcontrollers-microprocessors/stm32f407ve.html", + "vendor": "ST" +} diff --git a/buildroot/share/PlatformIO/scripts/STM32F103RC_MEEB_3DP.py b/buildroot/share/PlatformIO/scripts/STM32F103RC_MEEB_3DP.py index a69520f46d..4f2da9cdc0 100644 --- a/buildroot/share/PlatformIO/scripts/STM32F103RC_MEEB_3DP.py +++ b/buildroot/share/PlatformIO/scripts/STM32F103RC_MEEB_3DP.py @@ -4,16 +4,16 @@ import pioutil if pioutil.is_pio_build(): - Import("env", "projenv") + Import("env", "projenv") - flash_size = 0 - vect_tab_addr = 0 + flash_size = 0 + vect_tab_addr = 0 - for define in env['CPPDEFINES']: - if define[0] == "VECT_TAB_ADDR": - vect_tab_addr = define[1] - if define[0] == "STM32_FLASH_SIZE": - flash_size = define[1] + for define in env['CPPDEFINES']: + if define[0] == "VECT_TAB_ADDR": + vect_tab_addr = define[1] + if define[0] == "STM32_FLASH_SIZE": + flash_size = define[1] - print('Use the {0:s} address as the marlin app entry point.'.format(vect_tab_addr)) - print('Use the {0:d}KB flash version of stm32f103rct6 chip.'.format(flash_size)) + print('Use the {0:s} address as the marlin app entry point.'.format(vect_tab_addr)) + print('Use the {0:d}KB flash version of stm32f103rct6 chip.'.format(flash_size)) diff --git a/buildroot/share/PlatformIO/scripts/STM32F103RC_fysetc.py b/buildroot/share/PlatformIO/scripts/STM32F103RC_fysetc.py index 2cab2ce5c1..ecb0cc145c 100644 --- a/buildroot/share/PlatformIO/scripts/STM32F103RC_fysetc.py +++ b/buildroot/share/PlatformIO/scripts/STM32F103RC_fysetc.py @@ -3,25 +3,25 @@ # import pioutil if pioutil.is_pio_build(): - from os.path import join - from os.path import expandvars - Import("env") + from os.path import join + from os.path import expandvars + Import("env") - # Custom HEX from ELF - env.AddPostAction( - join("$BUILD_DIR", "${PROGNAME}.elf"), - env.VerboseAction(" ".join([ - "$OBJCOPY", "-O ihex", "$TARGET", - "\"" + join("$BUILD_DIR", "${PROGNAME}.hex") + "\"", # Note: $BUILD_DIR is a full path - ]), "Building $TARGET")) + # Custom HEX from ELF + env.AddPostAction( + join("$BUILD_DIR", "${PROGNAME}.elf"), + env.VerboseAction(" ".join([ + "$OBJCOPY", "-O ihex", "$TARGET", + "\"" + join("$BUILD_DIR", "${PROGNAME}.hex") + "\"", # Note: $BUILD_DIR is a full path + ]), "Building $TARGET")) - # In-line command with arguments - UPLOAD_TOOL="stm32flash" - platform = env.PioPlatform() - if platform.get_package_dir("tool-stm32duino") != None: - UPLOAD_TOOL=expandvars("\"" + join(platform.get_package_dir("tool-stm32duino"),"stm32flash","stm32flash") + "\"") + # In-line command with arguments + UPLOAD_TOOL="stm32flash" + platform = env.PioPlatform() + if platform.get_package_dir("tool-stm32duino") != None: + UPLOAD_TOOL=expandvars("\"" + join(platform.get_package_dir("tool-stm32duino"),"stm32flash","stm32flash") + "\"") - env.Replace( - UPLOADER=UPLOAD_TOOL, - UPLOADCMD=expandvars(UPLOAD_TOOL + " -v -i rts,-dtr,dtr -R -b 115200 -g 0x8000000 -w \"" + join("$BUILD_DIR","${PROGNAME}.hex")+"\"" + " $UPLOAD_PORT") - ) + env.Replace( + UPLOADER=UPLOAD_TOOL, + UPLOADCMD=expandvars(UPLOAD_TOOL + " -v -i rts,-dtr,dtr -R -b 115200 -g 0x8000000 -w \"" + join("$BUILD_DIR","${PROGNAME}.hex")+"\"" + " $UPLOAD_PORT") + ) diff --git a/buildroot/share/PlatformIO/scripts/STM32F1_create_variant.py b/buildroot/share/PlatformIO/scripts/STM32F1_create_variant.py index 0eab7a8361..4189cb5899 100644 --- a/buildroot/share/PlatformIO/scripts/STM32F1_create_variant.py +++ b/buildroot/share/PlatformIO/scripts/STM32F1_create_variant.py @@ -3,29 +3,29 @@ # import pioutil if pioutil.is_pio_build(): - import shutil,marlin - from pathlib import Path + import shutil,marlin + from pathlib import Path - Import("env") - platform = env.PioPlatform() - board = env.BoardConfig() + Import("env") + platform = env.PioPlatform() + board = env.BoardConfig() - FRAMEWORK_DIR = Path(platform.get_package_dir("framework-arduinoststm32-maple")) - assert FRAMEWORK_DIR.is_dir() + FRAMEWORK_DIR = Path(platform.get_package_dir("framework-arduinoststm32-maple")) + assert FRAMEWORK_DIR.is_dir() - source_root = Path("buildroot/share/PlatformIO/variants") - assert source_root.is_dir() + source_root = Path("buildroot/share/PlatformIO/variants") + assert source_root.is_dir() - variant = board.get("build.variant") - variant_dir = FRAMEWORK_DIR / "STM32F1/variants" / variant + variant = board.get("build.variant") + variant_dir = FRAMEWORK_DIR / "STM32F1/variants" / variant - source_dir = source_root / variant - assert source_dir.is_dir() + source_dir = source_root / variant + assert source_dir.is_dir() - if variant_dir.is_dir(): - shutil.rmtree(variant_dir) + if variant_dir.is_dir(): + shutil.rmtree(variant_dir) - if not variant_dir.is_dir(): - variant_dir.mkdir() + if not variant_dir.is_dir(): + variant_dir.mkdir() - marlin.copytree(source_dir, variant_dir) + marlin.copytree(source_dir, variant_dir) diff --git a/buildroot/share/PlatformIO/scripts/preflight-checks.py b/buildroot/share/PlatformIO/scripts/preflight-checks.py index 08fe20c817..cc80c76421 100644 --- a/buildroot/share/PlatformIO/scripts/preflight-checks.py +++ b/buildroot/share/PlatformIO/scripts/preflight-checks.py @@ -60,10 +60,10 @@ if pioutil.is_pio_build(): raise SystemExit("Error: Marlin requires PlatformIO >= 6.1.1. Use 'pio upgrade' to get a newer version.") if 'MARLIN_FEATURES' not in env: - raise SystemExit("Error: this script should be used after common Marlin scripts") + raise SystemExit("Error: this script should be used after common Marlin scripts.") - if 'MOTHERBOARD' not in env['MARLIN_FEATURES']: - raise SystemExit("Error: MOTHERBOARD is not defined in Configuration.h") + if len(env['MARLIN_FEATURES']) == 0: + raise SystemExit("Error: Failed to parse Marlin features. See previous error messages.") build_env = env['PIOENV'] motherboard = env['MARLIN_FEATURES']['MOTHERBOARD'] diff --git a/buildroot/share/PlatformIO/variants/MARLIN_ARTILLERY_RUBY/hal_conf_custom.h b/buildroot/share/PlatformIO/variants/MARLIN_ARTILLERY_RUBY/hal_conf_custom.h index 9fa98807d6..bbce8a1c9a 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_ARTILLERY_RUBY/hal_conf_custom.h +++ b/buildroot/share/PlatformIO/variants/MARLIN_ARTILLERY_RUBY/hal_conf_custom.h @@ -5,8 +5,8 @@ ****************************************************************************** * @attention * - *

© Copyright (c) 2017 STMicroelectronics. - * All rights reserved.

+ * Copyright (c) 2017 STMicroelectronics. + * All rights reserved. * * This software component is licensed by ST under BSD 3-Clause license, * the "License"; You may not use this file except in compliance with the diff --git a/buildroot/share/PlatformIO/variants/MARLIN_ARTILLERY_RUBY/ldscript.ld b/buildroot/share/PlatformIO/variants/MARLIN_ARTILLERY_RUBY/ldscript.ld index 57c01c8df8..0f8a490044 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_ARTILLERY_RUBY/ldscript.ld +++ b/buildroot/share/PlatformIO/variants/MARLIN_ARTILLERY_RUBY/ldscript.ld @@ -20,7 +20,7 @@ ***************************************************************************** ** @attention ** -**

© COPYRIGHT(c) 2014 Ac6

+** Copyright (c) 2014 Ac6 ** ** Redistribution and use in source and binary forms, with or without modification, ** are permitted provided that the following conditions are met: diff --git a/buildroot/share/PlatformIO/variants/MARLIN_ARTILLERY_RUBY/startup.S b/buildroot/share/PlatformIO/variants/MARLIN_ARTILLERY_RUBY/startup.S index 81999dda6a..9348cd057a 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_ARTILLERY_RUBY/startup.S +++ b/buildroot/share/PlatformIO/variants/MARLIN_ARTILLERY_RUBY/startup.S @@ -16,7 +16,7 @@ ****************************************************************************** * @attention * - *

© COPYRIGHT 2015 STMicroelectronics

+ * Copyright (c) 2015 STMicroelectronics * * Redistribution and use in source and binary forms, with or without modification, * are permitted provided that the following conditions are met: diff --git a/buildroot/share/PlatformIO/variants/MARLIN_BIGTREE_BTT002/ldscript.ld b/buildroot/share/PlatformIO/variants/MARLIN_BIGTREE_BTT002/ldscript.ld index 6af296a521..f7e09b8ef0 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_BIGTREE_BTT002/ldscript.ld +++ b/buildroot/share/PlatformIO/variants/MARLIN_BIGTREE_BTT002/ldscript.ld @@ -21,7 +21,7 @@ ***************************************************************************** ** @attention ** -**

© COPYRIGHT(c) 2014 Ac6

+** Copyright (c) 2014 Ac6 ** ** Redistribution and use in source and binary forms, with or without modification, ** are permitted provided that the following conditions are met: diff --git a/buildroot/share/PlatformIO/variants/MARLIN_BIGTREE_E3_RRF/ldscript.ld b/buildroot/share/PlatformIO/variants/MARLIN_BIGTREE_E3_RRF/ldscript.ld index 6af296a521..f7e09b8ef0 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_BIGTREE_E3_RRF/ldscript.ld +++ b/buildroot/share/PlatformIO/variants/MARLIN_BIGTREE_E3_RRF/ldscript.ld @@ -21,7 +21,7 @@ ***************************************************************************** ** @attention ** -**

© COPYRIGHT(c) 2014 Ac6

+** Copyright (c) 2014 Ac6 ** ** Redistribution and use in source and binary forms, with or without modification, ** are permitted provided that the following conditions are met: diff --git a/buildroot/share/PlatformIO/variants/MARLIN_BIGTREE_GTR_V1/ldscript.ld b/buildroot/share/PlatformIO/variants/MARLIN_BIGTREE_GTR_V1/ldscript.ld index 6af296a521..f7e09b8ef0 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_BIGTREE_GTR_V1/ldscript.ld +++ b/buildroot/share/PlatformIO/variants/MARLIN_BIGTREE_GTR_V1/ldscript.ld @@ -21,7 +21,7 @@ ***************************************************************************** ** @attention ** -**

© COPYRIGHT(c) 2014 Ac6

+** Copyright (c) 2014 Ac6 ** ** Redistribution and use in source and binary forms, with or without modification, ** are permitted provided that the following conditions are met: diff --git a/buildroot/share/PlatformIO/variants/MARLIN_BIGTREE_OCTOPUS_PRO_V1_F429/ldscript.ld b/buildroot/share/PlatformIO/variants/MARLIN_BIGTREE_OCTOPUS_PRO_V1_F429/ldscript.ld index 4cac4ac6e2..063525c964 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_BIGTREE_OCTOPUS_PRO_V1_F429/ldscript.ld +++ b/buildroot/share/PlatformIO/variants/MARLIN_BIGTREE_OCTOPUS_PRO_V1_F429/ldscript.ld @@ -21,7 +21,7 @@ ***************************************************************************** ** @attention ** -**

© COPYRIGHT(c) 2014 Ac6

+** Copyright (c) 2014 Ac6 ** ** Redistribution and use in source and binary forms, with or without modification, ** are permitted provided that the following conditions are met: diff --git a/buildroot/share/PlatformIO/variants/MARLIN_BIGTREE_OCTOPUS_V1/ldscript.ld b/buildroot/share/PlatformIO/variants/MARLIN_BIGTREE_OCTOPUS_V1/ldscript.ld index ca21498cd2..ed6cae4379 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_BIGTREE_OCTOPUS_V1/ldscript.ld +++ b/buildroot/share/PlatformIO/variants/MARLIN_BIGTREE_OCTOPUS_V1/ldscript.ld @@ -21,7 +21,7 @@ ***************************************************************************** ** @attention ** -**

© COPYRIGHT(c) 2014 Ac6

+** Copyright (c) 2014 Ac6 ** ** Redistribution and use in source and binary forms, with or without modification, ** are permitted provided that the following conditions are met: diff --git a/buildroot/share/PlatformIO/variants/MARLIN_BIGTREE_SKR_PRO_11/ldscript.ld b/buildroot/share/PlatformIO/variants/MARLIN_BIGTREE_SKR_PRO_11/ldscript.ld index 6af296a521..f7e09b8ef0 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_BIGTREE_SKR_PRO_11/ldscript.ld +++ b/buildroot/share/PlatformIO/variants/MARLIN_BIGTREE_SKR_PRO_11/ldscript.ld @@ -21,7 +21,7 @@ ***************************************************************************** ** @attention ** -**

© COPYRIGHT(c) 2014 Ac6

+** Copyright (c) 2014 Ac6 ** ** Redistribution and use in source and binary forms, with or without modification, ** are permitted provided that the following conditions are met: diff --git a/buildroot/share/PlatformIO/variants/MARLIN_BTT_SKR_SE_BX/hal_conf_extra.h b/buildroot/share/PlatformIO/variants/MARLIN_BTT_SKR_SE_BX/hal_conf_extra.h index 92730f5945..f355549a67 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_BTT_SKR_SE_BX/hal_conf_extra.h +++ b/buildroot/share/PlatformIO/variants/MARLIN_BTT_SKR_SE_BX/hal_conf_extra.h @@ -5,8 +5,8 @@ ****************************************************************************** * @attention * - *

© Copyright (c) 2017 STMicroelectronics. - * All rights reserved.

+ * Copyright (c) 2017 STMicroelectronics. + * All rights reserved. * * This software component is licensed by ST under BSD 3-Clause license, * the "License"; You may not use this file except in compliance with the diff --git a/buildroot/share/PlatformIO/variants/MARLIN_BTT_SKR_SE_BX/ldscript.ld b/buildroot/share/PlatformIO/variants/MARLIN_BTT_SKR_SE_BX/ldscript.ld index 006c87a17a..931091bc31 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_BTT_SKR_SE_BX/ldscript.ld +++ b/buildroot/share/PlatformIO/variants/MARLIN_BTT_SKR_SE_BX/ldscript.ld @@ -26,7 +26,7 @@ ***************************************************************************** ** @attention ** -**

© COPYRIGHT(c) 2019 STMicroelectronics

+** Copyright (c) 2019 STMicroelectronics ** ** Redistribution and use in source and binary forms, with or without modification, ** are permitted provided that the following conditions are met: diff --git a/buildroot/share/PlatformIO/variants/MARLIN_CREALITY_STM32F401RC/hal_conf_custom.h b/buildroot/share/PlatformIO/variants/MARLIN_CREALITY_STM32F401RC/hal_conf_custom.h index 1dd047bb90..808b5588ed 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_CREALITY_STM32F401RC/hal_conf_custom.h +++ b/buildroot/share/PlatformIO/variants/MARLIN_CREALITY_STM32F401RC/hal_conf_custom.h @@ -5,8 +5,8 @@ ****************************************************************************** * @attention * - *

© Copyright (c) 2017 STMicroelectronics. - * All rights reserved.

+ * Copyright (c) 2017 STMicroelectronics. + * All rights reserved. * * This software component is licensed by ST under BSD 3-Clause license, * the "License"; You may not use this file except in compliance with the diff --git a/buildroot/share/PlatformIO/variants/MARLIN_CREALITY_STM32F401RC/ldscript.ld b/buildroot/share/PlatformIO/variants/MARLIN_CREALITY_STM32F401RC/ldscript.ld index 004714cd6d..d12edc7197 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_CREALITY_STM32F401RC/ldscript.ld +++ b/buildroot/share/PlatformIO/variants/MARLIN_CREALITY_STM32F401RC/ldscript.ld @@ -21,7 +21,7 @@ ***************************************************************************** ** @attention ** -**

© COPYRIGHT(c) 2014 Ac6

+** Copyright (c) 2014 Ac6 ** ** Redistribution and use in source and binary forms, with or without modification, ** are permitted provided that the following conditions are met: @@ -184,4 +184,4 @@ SECTIONS } .ARM.attributes 0 : { *(.ARM.attributes) } -} \ No newline at end of file +} diff --git a/buildroot/share/PlatformIO/variants/MARLIN_F103Rx/ldscript.ld b/buildroot/share/PlatformIO/variants/MARLIN_F103Rx/ldscript.ld index cd7503b3a5..4eb277cb06 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_F103Rx/ldscript.ld +++ b/buildroot/share/PlatformIO/variants/MARLIN_F103Rx/ldscript.ld @@ -23,7 +23,7 @@ ***************************************************************************** ** @attention ** -**

© COPYRIGHT(c) 2019 STMicroelectronics

+** Copyright (c) 2019 STMicroelectronics ** ** Redistribution and use in source and binary forms, with or without modification, ** are permitted provided that the following conditions are met: diff --git a/buildroot/share/PlatformIO/variants/MARLIN_F103VE_LONGER/ldscript.ld b/buildroot/share/PlatformIO/variants/MARLIN_F103VE_LONGER/ldscript.ld index 6bc577236a..a1042aa8d2 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_F103VE_LONGER/ldscript.ld +++ b/buildroot/share/PlatformIO/variants/MARLIN_F103VE_LONGER/ldscript.ld @@ -22,7 +22,7 @@ ***************************************************************************** ** @attention ** -**

© COPYRIGHT(c) 2019 STMicroelectronics

+** Copyright (c) 2019 STMicroelectronics ** ** Redistribution and use in source and binary forms, with or without modification, ** are permitted provided that the following conditions are met: diff --git a/buildroot/share/PlatformIO/variants/MARLIN_F103Vx/ldscript.ld b/buildroot/share/PlatformIO/variants/MARLIN_F103Vx/ldscript.ld index a65b07d61c..3013b09607 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_F103Vx/ldscript.ld +++ b/buildroot/share/PlatformIO/variants/MARLIN_F103Vx/ldscript.ld @@ -23,7 +23,7 @@ ***************************************************************************** ** @attention ** -**

© COPYRIGHT(c) 2019 STMicroelectronics

+** Copyright (c) 2019 STMicroelectronics ** ** Redistribution and use in source and binary forms, with or without modification, ** are permitted provided that the following conditions are met: diff --git a/buildroot/share/PlatformIO/variants/MARLIN_F103Zx/hal_conf_custom.h b/buildroot/share/PlatformIO/variants/MARLIN_F103Zx/hal_conf_custom.h index 2443052621..a9475dbdd9 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_F103Zx/hal_conf_custom.h +++ b/buildroot/share/PlatformIO/variants/MARLIN_F103Zx/hal_conf_custom.h @@ -5,8 +5,8 @@ ****************************************************************************** * @attention * - *

© Copyright (c) 2017 STMicroelectronics. - * All rights reserved.

+ * Copyright (c) 2017 STMicroelectronics. + * All rights reserved. * * This software component is licensed by ST under BSD 3-Clause license, * the "License"; You may not use this file except in compliance with the diff --git a/buildroot/share/PlatformIO/variants/MARLIN_F103Zx/ldscript.ld b/buildroot/share/PlatformIO/variants/MARLIN_F103Zx/ldscript.ld index cc4b323f76..cac12da5c2 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_F103Zx/ldscript.ld +++ b/buildroot/share/PlatformIO/variants/MARLIN_F103Zx/ldscript.ld @@ -23,7 +23,7 @@ ***************************************************************************** ** @attention ** -**

© COPYRIGHT(c) 2019 STMicroelectronics

+** Copyright (c) 2019 STMicroelectronics ** ** Redistribution and use in source and binary forms, with or without modification, ** are permitted provided that the following conditions are met: diff --git a/buildroot/share/PlatformIO/variants/MARLIN_F401RC/ldscript.ld b/buildroot/share/PlatformIO/variants/MARLIN_F401RC/ldscript.ld index a0ab41f631..c7e67d311e 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_F401RC/ldscript.ld +++ b/buildroot/share/PlatformIO/variants/MARLIN_F401RC/ldscript.ld @@ -13,8 +13,8 @@ ****************************************************************************** * @attention * - *

© Copyright (c) 2020 STMicroelectronics. - * All rights reserved.

+ * Copyright (c) 2020 STMicroelectronics. + * All rights reserved. * * This software component is licensed by ST under BSD 3-Clause license, * the "License"; You may not use this file except in compliance with the diff --git a/buildroot/share/PlatformIO/variants/MARLIN_F407VE/hal_conf_custom.h b/buildroot/share/PlatformIO/variants/MARLIN_F407VE/hal_conf_custom.h index 58e9646b57..ea5e2cc709 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_F407VE/hal_conf_custom.h +++ b/buildroot/share/PlatformIO/variants/MARLIN_F407VE/hal_conf_custom.h @@ -5,8 +5,8 @@ ****************************************************************************** * @attention * - *

© Copyright (c) 2017 STMicroelectronics. - * All rights reserved.

+ * Copyright (c) 2017 STMicroelectronics. + * All rights reserved. * * This software component is licensed by ST under BSD 3-Clause license, * the "License"; You may not use this file except in compliance with the diff --git a/buildroot/share/PlatformIO/variants/MARLIN_F407VE/ldscript.ld b/buildroot/share/PlatformIO/variants/MARLIN_F407VE/ldscript.ld index 68b6597322..9357c4b52c 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_F407VE/ldscript.ld +++ b/buildroot/share/PlatformIO/variants/MARLIN_F407VE/ldscript.ld @@ -21,7 +21,7 @@ ***************************************************************************** ** @attention ** -**

© COPYRIGHT(c) 2014 Ac6

+** Copyright (c) 2014 Ac6 ** ** Redistribution and use in source and binary forms, with or without modification, ** are permitted provided that the following conditions are met: diff --git a/buildroot/share/PlatformIO/variants/MARLIN_F446VE/ldscript.ld b/buildroot/share/PlatformIO/variants/MARLIN_F446VE/ldscript.ld index a375232d59..7d5307717c 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_F446VE/ldscript.ld +++ b/buildroot/share/PlatformIO/variants/MARLIN_F446VE/ldscript.ld @@ -20,7 +20,7 @@ ***************************************************************************** ** @attention ** -**

© COPYRIGHT(c) 2014 Ac6

+** Copyright (c) 2014 Ac6 ** ** Redistribution and use in source and binary forms, with or without modification, ** are permitted provided that the following conditions are met: diff --git a/buildroot/share/PlatformIO/variants/MARLIN_F4x7Vx/hal_conf_extra.h b/buildroot/share/PlatformIO/variants/MARLIN_F4x7Vx/hal_conf_extra.h index d246a1e745..f2f4ed3e96 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_F4x7Vx/hal_conf_extra.h +++ b/buildroot/share/PlatformIO/variants/MARLIN_F4x7Vx/hal_conf_extra.h @@ -8,8 +8,8 @@ ****************************************************************************** * @attention * - *

© Copyright (c) 2017 STMicroelectronics. - * All rights reserved.

+ * Copyright (c) 2017 STMicroelectronics. + * All rights reserved. * * This software component is licensed by ST under BSD 3-Clause license, * the "License"; You may not use this file except in compliance with the diff --git a/buildroot/share/PlatformIO/variants/MARLIN_F4x7Vx/ldscript.ld b/buildroot/share/PlatformIO/variants/MARLIN_F4x7Vx/ldscript.ld index 8b38135a2a..df1ed1581a 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_F4x7Vx/ldscript.ld +++ b/buildroot/share/PlatformIO/variants/MARLIN_F4x7Vx/ldscript.ld @@ -19,7 +19,7 @@ ***************************************************************************** ** @attention ** -**

© COPYRIGHT(c) 2019 STMicroelectronics

+** Copyright (c) 2019 STMicroelectronics ** ** Redistribution and use in source and binary forms, with or without modification, ** are permitted provided that the following conditions are met: diff --git a/buildroot/share/PlatformIO/variants/MARLIN_F4x7Vx/variant.h b/buildroot/share/PlatformIO/variants/MARLIN_F4x7Vx/variant.h index ba145d058c..0b78be627f 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_F4x7Vx/variant.h +++ b/buildroot/share/PlatformIO/variants/MARLIN_F4x7Vx/variant.h @@ -27,98 +27,98 @@ extern "C" { * Pins *----------------------------------------------------------------------------*/ -// | DIGITAL | ANALOG IN | ANALOG OUT | UART/USART | TWI | SPI | SPECIAL | -// |---------|------------|------------|-----------------------|----------------------|-----------------------------------|-----------| -#define PA0 PIN_A0 // | 0 | A0 (ADC1) | | UART4_TX | | | | -#define PA1 PIN_A1 // | 1 | A1 (ADC1) | | UART4_RX | | | | -#define PA2 PIN_A2 // | 2 | A2 (ADC1) | | USART2_TX | | | | -#define PA3 PIN_A3 // | 3 | A3 (ADC1) | | USART2_RX | | | | -#define PA4 PIN_A4 // | 4 | A4 (ADC1) | DAC_OUT1 | | | SPI1_SS, (SPI3_SS) | | -#define PA5 PIN_A5 // | 5 | A5 (ADC1) | DAC_OUT2 | | | SPI1_SCK | | -#define PA6 PIN_A6 // | 6 | A6 (ADC1) | | | | SPI1_MISO | | -#define PA7 PIN_A7 // | 7 | A7 (ADC1) | | | | SPI1_MOSI | | -#define PA8 8 // | 8 | | | | TWI3_SCL | | | -#define PA9 9 // | 9 | | | USART1_TX | | | | -#define PA10 10 // | 10 | | | USART1_RX | | | | -#define PA11 11 // | 11 | | | | | | | -#define PA12 12 // | 12 | | | | | | | -#define PA13 13 // | 13 | | | | | | SWD_SWDIO | -#define PA14 14 // | 14 | | | | | | SWD_SWCLK | -#define PA15 15 // | 15 | | | | | SPI3_SS, (SPI1_SS) | | -// |---------|------------|------------|-----------------------|----------------------|-----------------------------------|-----------| -#define PB0 PIN_A8 // | 16 | A8 (ADC1) | | | | | | -#define PB1 PIN_A9 // | 17 | A9 (ADC1) | | | | | | -#define PB2 18 // | 18 | | | | | | BOOT1 | -#define PB3 19 // | 19 | | | | | SPI3_SCK, (SPI1_SCK) | | -#define PB4 20 // | 20 | | | | | SPI3_MISO, (SPI1_MISO) | | -#define PB5 21 // | 21 | | | | | SPI3_MOSI, (SPI1_MOSI) | | -#define PB6 22 // | 22 | | | USART1_TX | TWI1_SCL | | | -#define PB7 23 // | 23 | | | USART1_RX | TWI1_SDA | | | -#define PB8 24 // | 24 | | | | TWI1_SCL | | | -#define PB9 25 // | 25 | | | | TWI1_SDA | SPI2_SS | | -#define PB10 26 // | 26 | | | USART3_TX, (UART4_TX) | TWI2_SCL | SPI2_SCK | | -#define PB11 27 // | 27 | | | USART3_RX | TWI2_SDA | | | -#define PB12 28 // | 28 | | | | | SPI2_SS | | -#define PB13 29 // | 29 | | | | | SPI2_SCK | | -#define PB14 30 // | 30 | | | | | SPI2_MISO | | -#define PB15 31 // | 31 | | | | | SPI2_MOSI | | -// |---------|------------|------------|-----------------------|----------------------|-----------------------------------|-----------| -#define PC0 PIN_A10 // | 32 | A10 (ADC1) | | | | | | -#define PC1 PIN_A11 // | 33 | A11 (ADC1) | | | | | | -#define PC2 PIN_A12 // | 34 | A12 (ADC1) | | | | SPI2_MISO | | -#define PC3 PIN_A13 // | 35 | A13 (ADC1) | | | | SPI2_MOSI | | -#define PC4 PIN_A14 // | 36 | A14 (ADC1) | | | | | | -#define PC5 PIN_A15 // | 37 | A15 (ADC1) | | USART3_RX | | | | -#define PC6 38 // | 38 | | | USART6_TX | | | | -#define PC7 39 // | 39 | | | USART6_RX | | | | -#define PC8 40 // | 40 | | | | | | | -#define PC9 41 // | 41 | | | USART3_TX | TWI3_SDA | | | -#define PC10 42 // | 42 | | | | | SPI3_SCK | | -#define PC11 43 // | 43 | | | USART3_RX, (UART4_RX) | | SPI3_MISO | | -#define PC12 44 // | 44 | | | UART5_TX | | SPI3_MOSI | | -#define PC13 45 // | 45 | | | | | | | -#define PC14 46 // | 46 | | | | | | OSC32_IN | -#define PC15 47 // | 47 | | | | | | OSC32_OUT | -// |---------|------------|------------|-----------------------|----------------------|-----------------------------------|-----------| -#define PD0 48 // | 48 | | | | | | | -#define PD1 49 // | 49 | | | | | | | -#define PD2 50 // | 50 | | | UART5_RX | | | | -#define PD3 51 // | 51 | | | | | | | -#define PD4 52 // | 52 | | | | | | | -#define PD5 53 // | 53 | | | USART2_TX | | | | -#define PD6 54 // | 54 | | | USART2_RX | | | | -#define PD7 55 // | 55 | | | | | | | -#define PD8 56 // | 56 | | | USART3_TX | | | | -#define PD9 57 // | 57 | | | USART3_RX | | | | -#define PD10 58 // | 58 | | | | | | | -#define PD11 59 // | 59 | | | | | | | -#define PD12 60 // | 60 | | | | | | | -#define PD13 61 // | 61 | | | | | | | -#define PD14 62 // | 62 | | | | | | | -#define PD15 63 // | 63 | | | | | | | -// |---------|------------|------------|-----------------------|----------------------|-----------------------------------|-----------| -#define PE0 64 // | 64 | | | | | | | -#define PE1 65 // | 65 | | | | | | | -#define PE2 66 // | 66 | | | | | | | -#define PE3 67 // | 67 | | | | | | | -#define PE4 68 // | 68 | | | | | | | -#define PE5 69 // | 69 | | | | | | | -#define PE6 70 // | 70 | | | | | | | -#define PE7 71 // | 71 | | | | | | | -#define PE8 72 // | 72 | | | | | | | -#define PE9 73 // | 73 | | | | | | | -#define PE10 74 // | 74 | | | | | | | -#define PE11 75 // | 75 | | | | | | | -#define PE12 76 // | 76 | | | | | | | -#define PE13 77 // | 77 | | | | | | | -#define PE14 78 // | 78 | | | | | | | -#define PE15 79 // | 79 | | | | | | | -// |---------|------------|------------|-----------------------|----------------------|-----------------------------------|-----------| -#define PH0 80 // | 80 | | | | | | OSC_IN | -#define PH1 81 // | 81 | | | | | | OSC_OUT | -// |---------|------------|------------|-----------------------|----------------------|-----------------------------------|-----------| + // | DIGITAL | ANALOG IN | ANALOG OUT | UART/USART | TWI | SPI | SPECIAL | + // |---------|------------|------------|-----------------------|----------------------|-----------------------------------|-----------| +#define PA0 PIN_A0 // | 0 | A0 (ADC1) | | UART4_TX | | | | +#define PA1 PIN_A1 // | 1 | A1 (ADC1) | | UART4_RX | | | | +#define PA2 PIN_A2 // | 2 | A2 (ADC1) | | USART2_TX | | | | +#define PA3 PIN_A3 // | 3 | A3 (ADC1) | | USART2_RX | | | | +#define PA4 PIN_A4 // | 4 | A4 (ADC1) | DAC_OUT1 | | | SPI1_SS, (SPI3_SS) | | +#define PA5 PIN_A5 // | 5 | A5 (ADC1) | DAC_OUT2 | | | SPI1_SCK | | +#define PA6 PIN_A6 // | 6 | A6 (ADC1) | | | | SPI1_MISO | | +#define PA7 PIN_A7 // | 7 | A7 (ADC1) | | | | SPI1_MOSI | | +#define PA8 8 // | 8 | | | | TWI3_SCL | | | +#define PA9 9 // | 9 | | | USART1_TX | | | | +#define PA10 10 // | 10 | | | USART1_RX | | | | +#define PA11 11 // | 11 | | | | | | | +#define PA12 12 // | 12 | | | | | | | +#define PA13 13 // | 13 | | | | | | SWD_SWDIO | +#define PA14 14 // | 14 | | | | | | SWD_SWCLK | +#define PA15 15 // | 15 | | | | | SPI3_SS, (SPI1_SS) | | + // |---------|------------|------------|-----------------------|----------------------|-----------------------------------|-----------| +#define PB0 PIN_A8 // | 16 | A8 (ADC1) | | | | | | +#define PB1 PIN_A9 // | 17 | A9 (ADC1) | | | | | | +#define PB2 18 // | 18 | | | | | | BOOT1 | +#define PB3 19 // | 19 | | | | | SPI3_SCK, (SPI1_SCK) | | +#define PB4 20 // | 20 | | | | | SPI3_MISO, (SPI1_MISO) | | +#define PB5 21 // | 21 | | | | | SPI3_MOSI, (SPI1_MOSI) | | +#define PB6 22 // | 22 | | | USART1_TX | TWI1_SCL | | | +#define PB7 23 // | 23 | | | USART1_RX | TWI1_SDA | | | +#define PB8 24 // | 24 | | | | TWI1_SCL | | | +#define PB9 25 // | 25 | | | | TWI1_SDA | SPI2_SS | | +#define PB10 26 // | 26 | | | USART3_TX, (UART4_TX) | TWI2_SCL | SPI2_SCK | | +#define PB11 27 // | 27 | | | USART3_RX | TWI2_SDA | | | +#define PB12 28 // | 28 | | | | | SPI2_SS | | +#define PB13 29 // | 29 | | | | | SPI2_SCK | | +#define PB14 30 // | 30 | | | | | SPI2_MISO | | +#define PB15 31 // | 31 | | | | | SPI2_MOSI | | + // |---------|------------|------------|-----------------------|----------------------|-----------------------------------|-----------| +#define PC0 PIN_A10 // | 32 | A10 (ADC1) | | | | | | +#define PC1 PIN_A11 // | 33 | A11 (ADC1) | | | | | | +#define PC2 PIN_A12 // | 34 | A12 (ADC1) | | | | SPI2_MISO | | +#define PC3 PIN_A13 // | 35 | A13 (ADC1) | | | | SPI2_MOSI | | +#define PC4 PIN_A14 // | 36 | A14 (ADC1) | | | | | | +#define PC5 PIN_A15 // | 37 | A15 (ADC1) | | USART3_RX | | | | +#define PC6 38 // | 38 | | | USART6_TX | | | | +#define PC7 39 // | 39 | | | USART6_RX | | | | +#define PC8 40 // | 40 | | | | | | | +#define PC9 41 // | 41 | | | USART3_TX | TWI3_SDA | | | +#define PC10 42 // | 42 | | | | | SPI3_SCK | | +#define PC11 43 // | 43 | | | USART3_RX, (UART4_RX) | | SPI3_MISO | | +#define PC12 44 // | 44 | | | UART5_TX | | SPI3_MOSI | | +#define PC13 45 // | 45 | | | | | | | +#define PC14 46 // | 46 | | | | | | OSC32_IN | +#define PC15 47 // | 47 | | | | | | OSC32_OUT | + // |---------|------------|------------|-----------------------|----------------------|-----------------------------------|-----------| +#define PD0 48 // | 48 | | | | | | | +#define PD1 49 // | 49 | | | | | | | +#define PD2 50 // | 50 | | | UART5_RX | | | | +#define PD3 51 // | 51 | | | | | | | +#define PD4 52 // | 52 | | | | | | | +#define PD5 53 // | 53 | | | USART2_TX | | | | +#define PD6 54 // | 54 | | | USART2_RX | | | | +#define PD7 55 // | 55 | | | | | | | +#define PD8 56 // | 56 | | | USART3_TX | | | | +#define PD9 57 // | 57 | | | USART3_RX | | | | +#define PD10 58 // | 58 | | | | | | | +#define PD11 59 // | 59 | | | | | | | +#define PD12 60 // | 60 | | | | | | | +#define PD13 61 // | 61 | | | | | | | +#define PD14 62 // | 62 | | | | | | | +#define PD15 63 // | 63 | | | | | | | + // |---------|------------|------------|-----------------------|----------------------|-----------------------------------|-----------| +#define PE0 64 // | 64 | | | | | | | +#define PE1 65 // | 65 | | | | | | | +#define PE2 66 // | 66 | | | | | | | +#define PE3 67 // | 67 | | | | | | | +#define PE4 68 // | 68 | | | | | | | +#define PE5 69 // | 69 | | | | | | | +#define PE6 70 // | 70 | | | | | | | +#define PE7 71 // | 71 | | | | | | | +#define PE8 72 // | 72 | | | | | | | +#define PE9 73 // | 73 | | | | | | | +#define PE10 74 // | 74 | | | | | | | +#define PE11 75 // | 75 | | | | | | | +#define PE12 76 // | 76 | | | | | | | +#define PE13 77 // | 77 | | | | | | | +#define PE14 78 // | 78 | | | | | | | +#define PE15 79 // | 79 | | | | | | | + // |---------|------------|------------|-----------------------|----------------------|-----------------------------------|-----------| +#define PH0 80 // | 80 | | | | | | OSC_IN | +#define PH1 81 // | 81 | | | | | | OSC_OUT | + // |---------|------------|------------|-----------------------|----------------------|-----------------------------------|-----------| -/// This must be a literal +// This must be a literal #define NUM_DIGITAL_PINS 82 #define NUM_ANALOG_INPUTS 16 diff --git a/buildroot/share/PlatformIO/variants/MARLIN_FLY_F407ZG/ldscript.ld b/buildroot/share/PlatformIO/variants/MARLIN_FLY_F407ZG/ldscript.ld index d644d49beb..cd7ccef85f 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_FLY_F407ZG/ldscript.ld +++ b/buildroot/share/PlatformIO/variants/MARLIN_FLY_F407ZG/ldscript.ld @@ -21,7 +21,7 @@ ***************************************************************************** ** @attention ** -**

© COPYRIGHT(c) 2014 Ac6

+** Copyright (c) 2014 Ac6 ** ** Redistribution and use in source and binary forms, with or without modification, ** are permitted provided that the following conditions are met: diff --git a/buildroot/share/PlatformIO/variants/MARLIN_FYSETC_CHEETAH_V20/hal_conf_custom.h b/buildroot/share/PlatformIO/variants/MARLIN_FYSETC_CHEETAH_V20/hal_conf_custom.h index 2ff2fd686e..fb3d21c6ac 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_FYSETC_CHEETAH_V20/hal_conf_custom.h +++ b/buildroot/share/PlatformIO/variants/MARLIN_FYSETC_CHEETAH_V20/hal_conf_custom.h @@ -5,8 +5,8 @@ ****************************************************************************** * @attention * - *

© Copyright (c) 2017 STMicroelectronics. - * All rights reserved.

+ * Copyright (c) 2017 STMicroelectronics. + * All rights reserved. * * This software component is licensed by ST under BSD 3-Clause license, * the "License"; You may not use this file except in compliance with the diff --git a/buildroot/share/PlatformIO/variants/MARLIN_FYSETC_CHEETAH_V20/ldscript.ld b/buildroot/share/PlatformIO/variants/MARLIN_FYSETC_CHEETAH_V20/ldscript.ld index eaaff196cd..1ded9f2a3e 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_FYSETC_CHEETAH_V20/ldscript.ld +++ b/buildroot/share/PlatformIO/variants/MARLIN_FYSETC_CHEETAH_V20/ldscript.ld @@ -21,7 +21,7 @@ ***************************************************************************** ** @attention ** -**

© COPYRIGHT(c) 2014 Ac6

+** Copyright (c) 2014 Ac6 ** ** Redistribution and use in source and binary forms, with or without modification, ** are permitted provided that the following conditions are met: @@ -184,4 +184,4 @@ SECTIONS } .ARM.attributes 0 : { *(.ARM.attributes) } -} \ No newline at end of file +} diff --git a/buildroot/share/PlatformIO/variants/MARLIN_FYSETC_S6/ldscript.ld b/buildroot/share/PlatformIO/variants/MARLIN_FYSETC_S6/ldscript.ld index 900ef06391..5db1528784 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_FYSETC_S6/ldscript.ld +++ b/buildroot/share/PlatformIO/variants/MARLIN_FYSETC_S6/ldscript.ld @@ -21,7 +21,7 @@ ***************************************************************************** ** @attention ** -**

© COPYRIGHT(c) 2014 Ac6

+** Copyright (c) 2014 Ac6 ** ** Redistribution and use in source and binary forms, with or without modification, ** are permitted provided that the following conditions are met: diff --git a/buildroot/share/PlatformIO/variants/MARLIN_FYSETC_SPIDER_KING407/PeripheralPins.c b/buildroot/share/PlatformIO/variants/MARLIN_FYSETC_SPIDER_KING407/PeripheralPins.c index 4205e10318..5c7c301f82 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_FYSETC_SPIDER_KING407/PeripheralPins.c +++ b/buildroot/share/PlatformIO/variants/MARLIN_FYSETC_SPIDER_KING407/PeripheralPins.c @@ -59,7 +59,7 @@ WEAK const PinMap PinMap_ADC[] = { //{PA_5, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 5, 0)}, // ADC2_IN5 //{PA_6, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC1_IN6 //{PA_6, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 6, 0)}, // ADC2_IN6 - //{PA_7, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC1_IN7 + //{PA_7, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC1_IN7 //{PA_7, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 7, 0)}, // ADC2_IN7 //{PB_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC1_IN8 //{PB_0, ADC2, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 8, 0)}, // ADC2_IN8 diff --git a/buildroot/share/PlatformIO/variants/MARLIN_FYSETC_SPIDER_KING407/ldscript.ld b/buildroot/share/PlatformIO/variants/MARLIN_FYSETC_SPIDER_KING407/ldscript.ld index 6af296a521..f7e09b8ef0 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_FYSETC_SPIDER_KING407/ldscript.ld +++ b/buildroot/share/PlatformIO/variants/MARLIN_FYSETC_SPIDER_KING407/ldscript.ld @@ -21,7 +21,7 @@ ***************************************************************************** ** @attention ** -**

© COPYRIGHT(c) 2014 Ac6

+** Copyright (c) 2014 Ac6 ** ** Redistribution and use in source and binary forms, with or without modification, ** are permitted provided that the following conditions are met: diff --git a/buildroot/share/PlatformIO/variants/MARLIN_G0B1RE/ldscript.ld b/buildroot/share/PlatformIO/variants/MARLIN_G0B1RE/ldscript.ld index 3b619b6a97..4e0e997341 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_G0B1RE/ldscript.ld +++ b/buildroot/share/PlatformIO/variants/MARLIN_G0B1RE/ldscript.ld @@ -13,8 +13,8 @@ ****************************************************************************** * @attention * - *

© Copyright (c) 2020 STMicroelectronics. - * All rights reserved.

+ * Copyright (c) 2020 STMicroelectronics. + * All rights reserved. * * This software component is licensed by ST under BSD 3-Clause license, * the "License"; You may not use this file except in compliance with the diff --git a/buildroot/share/PlatformIO/variants/MARLIN_G0B1RE/variant_MARLIN_STM32G0B1RE.h b/buildroot/share/PlatformIO/variants/MARLIN_G0B1RE/variant_MARLIN_STM32G0B1RE.h index 9cb3d45a0d..6a26baff45 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_G0B1RE/variant_MARLIN_STM32G0B1RE.h +++ b/buildroot/share/PlatformIO/variants/MARLIN_G0B1RE/variant_MARLIN_STM32G0B1RE.h @@ -124,6 +124,7 @@ #define NUM_DIGITAL_PINS 62 #define NUM_REMAP_PINS 2 #define NUM_ANALOG_INPUTS 16 +#define NUM_ANALOG_FIRST PA0 // SPI definitions #ifndef PIN_SPI_SS diff --git a/buildroot/share/PlatformIO/variants/MARLIN_H743Vx/ldscript.ld b/buildroot/share/PlatformIO/variants/MARLIN_H743Vx/ldscript.ld index 7d248a2682..5f439f3f8e 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_H743Vx/ldscript.ld +++ b/buildroot/share/PlatformIO/variants/MARLIN_H743Vx/ldscript.ld @@ -26,7 +26,7 @@ ***************************************************************************** ** @attention ** -**

© COPYRIGHT(c) 2019 STMicroelectronics

+** Copyright (c) 2019 STMicroelectronics ** ** Redistribution and use in source and binary forms, with or without modification, ** are permitted provided that the following conditions are met: diff --git a/buildroot/share/PlatformIO/variants/MARLIN_MKS_SKIPR_V1/PeripheralPins.c b/buildroot/share/PlatformIO/variants/MARLIN_MKS_SKIPR_V1/PeripheralPins.c new file mode 100644 index 0000000000..640fbdbe13 --- /dev/null +++ b/buildroot/share/PlatformIO/variants/MARLIN_MKS_SKIPR_V1/PeripheralPins.c @@ -0,0 +1,169 @@ +/* + ******************************************************************************* + * Copyright (c) 2016, STMicroelectronics + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + ******************************************************************************* + */ +#include "Arduino.h" +#include "PeripheralPins.h" + +// ===== +// Note: Commented lines are alternative possibilities which are not used per default. +// If you change them, you will have to know what you do +// ===== + +//*** ADC *** + +#ifdef HAL_ADC_MODULE_ENABLED +WEAK const PinMap PinMap_ADC[] = { + {PC_0, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 10, 0)}, // ADC1_IN10 THBED + {PC_1, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 11, 0)}, // ADC1_IN11 TH0 + {PC_2, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 12, 0)}, // ADC1_IN12 TH1 + {PC_3, ADC1, STM_PIN_DATA_EXT(STM_MODE_ANALOG, GPIO_NOPULL, 0, 13, 0)}, // ADC1_IN13 TH2 + {NC, NP, 0} +}; +#endif + +//*** I2C *** + +#ifdef HAL_I2C_MODULE_ENABLED +WEAK const PinMap PinMap_I2C_SDA[] = { + {PB_9, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)}, + {NC, NP, 0} +}; + +WEAK const PinMap PinMap_I2C_SCL[] = { + {PB_8, I2C1, STM_PIN_DATA(STM_MODE_AF_OD, GPIO_NOPULL, GPIO_AF4_I2C1)}, + {NC, NP, 0} +}; +#endif + +//*** PWM *** + +#ifdef HAL_TIM_MODULE_ENABLED +// Some pins can perform PWM from more than one timer. These were selected to utilize as many channels as +// possible from timers which were already dedicated to PWM output. + +// TIM1 = HEATER0, HEATER1, [SERVO] +// TIM2 = FAN1, FAN2, [BEEPER] +// TIM4 = HEATER_BED +// TIM5 = HEATER2, FAN0 + +WEAK const PinMap PinMap_PWM[] = { + {PA_0, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 1, 0)}, // TIM2_CH1 Fan2 + {PA_1, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 2, 0)}, // TIM2_CH2 Fan1 + {PA_2, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 3, 0)}, // TIM5_CH3 Fan0 + {PA_3, TIM5, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM5, 4, 0)}, // TIM5_CH4 HE2 + {PA_8, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 1, 0)}, // TIM1_CH1 Servo + {PB_0, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 2, 1)}, // TIM1_CH2N HE1 + {PB_1, TIM1, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM1, 3, 1)}, // TIM1_CH3N HE0 + {PB_2, TIM2, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF1_TIM2, 4, 0)}, // TIM2_CH4 BEEPER + {PD_12, TIM4, STM_PIN_DATA_EXT(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF2_TIM4, 1, 0)}, // TIM4_CH1 HOTBED + {NC, NP, 0} +}; +#endif + +//*** SERIAL *** + +#ifdef HAL_UART_MODULE_ENABLED +WEAK const PinMap PinMap_UART_TX[] = { + {PA_9, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)}, + {PB_10, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART3)}, + {NC, NP, 0} +}; + +WEAK const PinMap PinMap_UART_RX[] = { + {PA_10, USART1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART1)}, + {PB_11, USART3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF7_USART3)}, + {NC, NP, 0} +}; + +WEAK const PinMap PinMap_UART_RTS[] = { + {NC, NP, 0} +}; + +WEAK const PinMap PinMap_UART_CTS[] = { + {NC, NP, 0} +}; +#endif + +//*** SPI *** + +#ifdef HAL_SPI_MODULE_ENABLED +WEAK const PinMap PinMap_SPI_MOSI[] = { + {PA_7, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + {PC_12, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)}, + {NC, NP, 0} +}; + +WEAK const PinMap PinMap_SPI_MISO[] = { + {PA_6, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + {PC_11, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)}, + {NC, NP, 0} +}; + +WEAK const PinMap PinMap_SPI_SCLK[] = { + {PA_5, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + {PC_10, SPI3, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF6_SPI3)}, + {NC, NP, 0} +}; + +WEAK const PinMap PinMap_SPI_SSEL[] = { + {PA_4, SPI1, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF5_SPI1)}, + {NC, NP, 0} +}; +#endif + +//*** CAN *** + +#ifdef HAL_CAN_MODULE_ENABLED +WEAK const PinMap PinMap_CAN_RD[] = { + {PB_12, CAN2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN2)}, + {NC, NP, 0} +}; + +const PinMap PinMap_CAN_TD[] = { + {PB_13, CAN2, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_NOPULL, GPIO_AF9_CAN2)}, + {NC, NP, 0} +}; +#endif + +//*** USB *** + +// If anyone for some unfathomable reason want to run gcode from Marlin's USB-C drive at 12Mbps - you can +#ifdef HAL_PCD_MODULE_ENABLED +WEAK const PinMap PinMap_USB_OTG_FS[] = { + {PA_11, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_DM + {PA_12, USB_OTG_FS, STM_PIN_DATA(STM_MODE_AF_PP, GPIO_PULLUP, GPIO_AF10_OTG_FS)}, // USB_OTG_FS_DP + {NC, NP, 0} +}; + +WEAK const PinMap PinMap_USB_OTG_HS[] = { + {NC, NP, 0} +}; +#endif + + diff --git a/buildroot/share/PlatformIO/variants/MARLIN_MKS_SKIPR_V1/PinNamesVar.h b/buildroot/share/PlatformIO/variants/MARLIN_MKS_SKIPR_V1/PinNamesVar.h new file mode 100644 index 0000000000..bff3f21349 --- /dev/null +++ b/buildroot/share/PlatformIO/variants/MARLIN_MKS_SKIPR_V1/PinNamesVar.h @@ -0,0 +1,30 @@ +/* SYS_WKUP */ +#ifdef PWR_WAKEUP_PIN1 + SYS_WKUP1 = PA_0, /* SYS_WKUP0 */ +#endif +#ifdef PWR_WAKEUP_PIN2 + SYS_WKUP2 = NC, +#endif +#ifdef PWR_WAKEUP_PIN3 + SYS_WKUP3 = NC, +#endif +#ifdef PWR_WAKEUP_PIN4 + SYS_WKUP4 = NC, +#endif +#ifdef PWR_WAKEUP_PIN5 + SYS_WKUP5 = NC, +#endif +#ifdef PWR_WAKEUP_PIN6 + SYS_WKUP6 = NC, +#endif +#ifdef PWR_WAKEUP_PIN7 + SYS_WKUP7 = NC, +#endif +#ifdef PWR_WAKEUP_PIN8 + SYS_WKUP8 = NC, +#endif +/* USB */ +#ifdef USBCON + USB_OTG_FS_DM = PA_11, + USB_OTG_FS_DP = PA_12, +#endif diff --git a/buildroot/share/PlatformIO/variants/MARLIN_MKS_SKIPR_V1/hal_conf_extra.h b/buildroot/share/PlatformIO/variants/MARLIN_MKS_SKIPR_V1/hal_conf_extra.h new file mode 100644 index 0000000000..2ca9df2efc --- /dev/null +++ b/buildroot/share/PlatformIO/variants/MARLIN_MKS_SKIPR_V1/hal_conf_extra.h @@ -0,0 +1,496 @@ +/** + ****************************************************************************** + * @file stm32f4xx_hal_conf_template.h + * @author MCD Application Team + * @brief HAL configuration template file. + * This file should be copied to the application folder and renamed + * to stm32f4xx_hal_conf.h. + ****************************************************************************** + * @attention + * + * Copyright (c) 2017 STMicroelectronics. + * All rights reserved. + * + * This software component is licensed by ST under BSD 3-Clause license, + * the "License"; You may not use this file except in compliance with the + * License. You may obtain a copy of the License at: + * opensource.org/licenses/BSD-3-Clause + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F4xx_HAL_CONF_H +#define __STM32F4xx_HAL_CONF_H + +#ifdef __cplusplus + extern "C" { +#endif + +/* Exported types ------------------------------------------------------------*/ +/* Exported constants --------------------------------------------------------*/ + +/* ########################## Module Selection ############################## */ +/** + * @brief This is the list of modules to be used in the HAL driver + */ +#define HAL_MODULE_ENABLED +#define HAL_ADC_MODULE_ENABLED +#define HAL_CAN_LEGACY_MODULE_ENABLED +#define HAL_CRC_MODULE_ENABLED +#define HAL_DAC_MODULE_ENABLED +#define HAL_DMA_MODULE_ENABLED +#define HAL_EXTI_MODULE_ENABLED // Needed for Endstop (and other external) Interrupts +#define HAL_GPIO_MODULE_ENABLED +#define HAL_I2C_MODULE_ENABLED +#define HAL_PWR_MODULE_ENABLED +#define HAL_RCC_MODULE_ENABLED +#define HAL_SPI_MODULE_ENABLED +#define HAL_TIM_MODULE_ENABLED +#define HAL_USART_MODULE_ENABLED +#define HAL_CORTEX_MODULE_ENABLED +// #define HAL_UART_MODULE_ENABLED +// #define HAL_PCD_MODULE_ENABLED + +// #define HAL_CAN_MODULE_ENABLED +//#define HAL_CEC_MODULE_ENABLED +//#define HAL_CRYP_MODULE_ENABLED +//#define HAL_DCMI_MODULE_ENABLED +//#define HAL_DMA2D_MODULE_ENABLED +//#define HAL_ETH_MODULE_ENABLED +//#define HAL_FLASH_MODULE_ENABLED +//#define HAL_NAND_MODULE_ENABLED +//#define HAL_NOR_MODULE_ENABLED +//#define HAL_PCCARD_MODULE_ENABLED +//#define HAL_SRAM_MODULE_ENABLED +//#define HAL_SDRAM_MODULE_ENABLED +//#define HAL_HASH_MODULE_ENABLED +//#define HAL_SMBUS_MODULE_ENABLED +//#define HAL_I2S_MODULE_ENABLED +//#define HAL_IWDG_MODULE_ENABLED +//#define HAL_LTDC_MODULE_ENABLED +//#define HAL_DSI_MODULE_ENABLED +//#define HAL_QSPI_MODULE_ENABLED +//#define HAL_RNG_MODULE_ENABLED +//#define HAL_RTC_MODULE_ENABLED +//#define HAL_SAI_MODULE_ENABLED +//#define HAL_SD_MODULE_ENABLED +//#define HAL_IRDA_MODULE_ENABLED +//#define HAL_SMARTCARD_MODULE_ENABLED +//#define HAL_WWDG_MODULE_ENABLED +//#define HAL_HCD_MODULE_ENABLED +//#define HAL_FMPI2C_MODULE_ENABLED +//#define HAL_SPDIFRX_MODULE_ENABLED +//#define HAL_DFSDM_MODULE_ENABLED +//#define HAL_LPTIM_MODULE_ENABLED +//#define HAL_MMC_MODULE_ENABLED + +/* ########################## HSE/HSI Values adaptation ##################### */ +/** + * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSE is used as system clock source, directly or through the PLL). + */ +#ifndef HSE_VALUE + #define HSE_VALUE 25000000U /*!< Value of the External oscillator in Hz */ +#endif /* HSE_VALUE */ + +#ifndef HSE_STARTUP_TIMEOUT + #define HSE_STARTUP_TIMEOUT 100U /*!< Time out for HSE start up, in ms */ +#endif /* HSE_STARTUP_TIMEOUT */ + +/** + * @brief Internal High Speed oscillator (HSI) value. + * This value is used by the RCC HAL module to compute the system frequency + * (when HSI is used as system clock source, directly or through the PLL). + */ +#ifndef HSI_VALUE + #define HSI_VALUE 16000000U /*!< Value of the Internal oscillator in Hz */ +#endif /* HSI_VALUE */ + +/** + * @brief Internal Low Speed oscillator (LSI) value. + */ +#ifndef LSI_VALUE + #define LSI_VALUE 32000U /*!< LSI Typical Value in Hz */ +#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz + The real value may vary depending on the variations + in voltage and temperature. */ +/** + * @brief External Low Speed oscillator (LSE) value. + */ +#ifndef LSE_VALUE + #define LSE_VALUE 32768U /*!< Value of the External Low Speed oscillator in Hz */ +#endif /* LSE_VALUE */ + +#ifndef LSE_STARTUP_TIMEOUT + #define LSE_STARTUP_TIMEOUT 5000U /*!< Time out for LSE start up, in ms */ +#endif /* LSE_STARTUP_TIMEOUT */ + +/** + * @brief External clock source for I2S peripheral + * This value is used by the I2S HAL module to compute the I2S clock source + * frequency, this source is inserted directly through I2S_CKIN pad. + */ +#ifndef EXTERNAL_CLOCK_VALUE + #define EXTERNAL_CLOCK_VALUE 12288000U /*!< Value of the External oscillator in Hz*/ +#endif /* EXTERNAL_CLOCK_VALUE */ + +/* Tip: To avoid modifying this file each time you need to use different HSE, + === you can define the HSE value in your toolchain compiler preprocessor. */ + +/* ########################### System Configuration ######################### */ +/** + * @brief This is the HAL system configuration section + */ +#define VDD_VALUE 3300U /*!< Value of VDD in mv */ +#define TICK_INT_PRIORITY 0x0FU /*!< tick interrupt priority */ +#define USE_RTOS 0U +#define PREFETCH_ENABLE 1U +#define INSTRUCTION_CACHE_ENABLE 1U +#define DATA_CACHE_ENABLE 1U + +#define USE_HAL_ADC_REGISTER_CALLBACKS 0U /* ADC register callback disabled */ +#define USE_HAL_CAN_REGISTER_CALLBACKS 0U /* CAN register callback disabled */ +#define USE_HAL_CEC_REGISTER_CALLBACKS 0U /* CEC register callback disabled */ +#define USE_HAL_CRYP_REGISTER_CALLBACKS 0U /* CRYP register callback disabled */ +#define USE_HAL_DAC_REGISTER_CALLBACKS 0U /* DAC register callback disabled */ +#define USE_HAL_DCMI_REGISTER_CALLBACKS 0U /* DCMI register callback disabled */ +#define USE_HAL_DFSDM_REGISTER_CALLBACKS 0U /* DFSDM register callback disabled */ +#define USE_HAL_DMA2D_REGISTER_CALLBACKS 0U /* DMA2D register callback disabled */ +#define USE_HAL_DSI_REGISTER_CALLBACKS 0U /* DSI register callback disabled */ +#define USE_HAL_ETH_REGISTER_CALLBACKS 0U /* ETH register callback disabled */ +#define USE_HAL_HASH_REGISTER_CALLBACKS 0U /* HASH register callback disabled */ +#define USE_HAL_HCD_REGISTER_CALLBACKS 0U /* HCD register callback disabled */ +#define USE_HAL_I2C_REGISTER_CALLBACKS 0U /* I2C register callback disabled */ +#define USE_HAL_FMPI2C_REGISTER_CALLBACKS 0U /* FMPI2C register callback disabled */ +#define USE_HAL_I2S_REGISTER_CALLBACKS 0U /* I2S register callback disabled */ +#define USE_HAL_IRDA_REGISTER_CALLBACKS 0U /* IRDA register callback disabled */ +#define USE_HAL_LPTIM_REGISTER_CALLBACKS 0U /* LPTIM register callback disabled */ +#define USE_HAL_LTDC_REGISTER_CALLBACKS 0U /* LTDC register callback disabled */ +#define USE_HAL_MMC_REGISTER_CALLBACKS 0U /* MMC register callback disabled */ +#define USE_HAL_NAND_REGISTER_CALLBACKS 0U /* NAND register callback disabled */ +#define USE_HAL_NOR_REGISTER_CALLBACKS 0U /* NOR register callback disabled */ +#define USE_HAL_PCCARD_REGISTER_CALLBACKS 0U /* PCCARD register callback disabled */ +#define USE_HAL_PCD_REGISTER_CALLBACKS 0U /* PCD register callback disabled */ +#define USE_HAL_QSPI_REGISTER_CALLBACKS 0U /* QSPI register callback disabled */ +#define USE_HAL_RNG_REGISTER_CALLBACKS 0U /* RNG register callback disabled */ +#define USE_HAL_RTC_REGISTER_CALLBACKS 0U /* RTC register callback disabled */ +#define USE_HAL_SAI_REGISTER_CALLBACKS 0U /* SAI register callback disabled */ +#define USE_HAL_SD_REGISTER_CALLBACKS 0U /* SD register callback disabled */ +#define USE_HAL_SMARTCARD_REGISTER_CALLBACKS 0U /* SMARTCARD register callback disabled */ +#define USE_HAL_SDRAM_REGISTER_CALLBACKS 0U /* SDRAM register callback disabled */ +#define USE_HAL_SRAM_REGISTER_CALLBACKS 0U /* SRAM register callback disabled */ +#define USE_HAL_SPDIFRX_REGISTER_CALLBACKS 0U /* SPDIFRX register callback disabled */ +#define USE_HAL_SMBUS_REGISTER_CALLBACKS 0U /* SMBUS register callback disabled */ +#define USE_HAL_SPI_REGISTER_CALLBACKS 0U /* SPI register callback disabled */ +#define USE_HAL_TIM_REGISTER_CALLBACKS 0U /* TIM register callback disabled */ +#define USE_HAL_UART_REGISTER_CALLBACKS 0U /* UART register callback disabled */ +#define USE_HAL_USART_REGISTER_CALLBACKS 0U /* USART register callback disabled */ +#define USE_HAL_WWDG_REGISTER_CALLBACKS 0U /* WWDG register callback disabled */ + +/* ########################## Assert Selection ############################## */ +/** + * @brief Uncomment the line below to expanse the "assert_param" macro in the + * HAL drivers code + */ +// #define USE_FULL_ASSERT 1U + +/* ################## Ethernet peripheral configuration ##################### */ + +/* Section 1 : Ethernet peripheral configuration */ + +/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */ +#define MAC_ADDR0 2U +#define MAC_ADDR1 0U +#define MAC_ADDR2 0U +#define MAC_ADDR3 0U +#define MAC_ADDR4 0U +#define MAC_ADDR5 0U + +/* Definition of the Ethernet driver buffers size and count */ +#define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ +#define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ +#define ETH_RXBUFNB 4U /* 4 Rx buffers of size ETH_RX_BUF_SIZE */ +#define ETH_TXBUFNB 4U /* 4 Tx buffers of size ETH_TX_BUF_SIZE */ + +/* Section 2: PHY configuration section */ + +/* DP83848 PHY Address*/ +#define DP83848_PHY_ADDRESS 0x01U +/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ +#define PHY_RESET_DELAY 0x000000FFU +/* PHY Configuration delay */ +#define PHY_CONFIG_DELAY 0x00000FFFU + +#define PHY_READ_TO 0x0000FFFFU +#define PHY_WRITE_TO 0x0000FFFFU + +/* Section 3: Common PHY Registers */ + +#define PHY_BCR ((uint16_t)0x0000) /*!< Transceiver Basic Control Register */ +#define PHY_BSR ((uint16_t)0x0001) /*!< Transceiver Basic Status Register */ + +#define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */ +#define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */ +#define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */ +#define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */ +#define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */ +#define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */ +#define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */ +#define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */ +#define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */ +#define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */ + +#define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */ +#define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */ +#define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */ + +/* Section 4: Extended PHY Registers */ + +#define PHY_SR ((uint16_t)0x0010) /*!< PHY status register Offset */ +#define PHY_MICR ((uint16_t)0x0011) /*!< MII Interrupt Control Register */ +#define PHY_MISR ((uint16_t)0x0012) /*!< MII Interrupt Status and Misc. Control Register */ + +#define PHY_LINK_STATUS ((uint16_t)0x0001) /*!< PHY Link mask */ +#define PHY_SPEED_STATUS ((uint16_t)0x0002) /*!< PHY Speed mask */ +#define PHY_DUPLEX_STATUS ((uint16_t)0x0004) /*!< PHY Duplex mask */ + +#define PHY_MICR_INT_EN ((uint16_t)0x0002) /*!< PHY Enable interrupts */ +#define PHY_MICR_INT_OE ((uint16_t)0x0001) /*!< PHY Enable output interrupt events */ + +#define PHY_MISR_LINK_INT_EN ((uint16_t)0x0020) /*!< Enable Interrupt on change of link status */ +#define PHY_LINK_INTERRUPT ((uint16_t)0x2000) /*!< PHY link status interrupt mask */ + +/* ################## SPI peripheral configuration ########################## */ + +/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver +* Activated: CRC code is present inside driver +* Deactivated: CRC code cleaned from driver +*/ + +#define USE_SPI_CRC 0U + +/* Includes ------------------------------------------------------------------*/ +/** + * @brief Include module's header file + */ + +#ifdef HAL_RCC_MODULE_ENABLED + #include "stm32f4xx_hal_rcc.h" +#endif /* HAL_RCC_MODULE_ENABLED */ + +#ifdef HAL_GPIO_MODULE_ENABLED + #include "stm32f4xx_hal_gpio.h" +#endif /* HAL_GPIO_MODULE_ENABLED */ + +#ifdef HAL_EXTI_MODULE_ENABLED + #include "stm32f4xx_hal_exti.h" +#endif /* HAL_EXTI_MODULE_ENABLED */ + +#ifdef HAL_DMA_MODULE_ENABLED + #include "stm32f4xx_hal_dma.h" +#endif /* HAL_DMA_MODULE_ENABLED */ + +#ifdef HAL_CORTEX_MODULE_ENABLED + #include "stm32f4xx_hal_cortex.h" +#endif /* HAL_CORTEX_MODULE_ENABLED */ + +#ifdef HAL_ADC_MODULE_ENABLED + #include "stm32f4xx_hal_adc.h" +#endif /* HAL_ADC_MODULE_ENABLED */ + +#ifdef HAL_CAN_MODULE_ENABLED + #include "stm32f4xx_hal_can.h" +#endif /* HAL_CAN_MODULE_ENABLED */ + +#ifdef HAL_CAN_LEGACY_MODULE_ENABLED + #include "stm32f4xx_hal_can_legacy.h" +#endif /* HAL_CAN_LEGACY_MODULE_ENABLED */ + +#ifdef HAL_CRC_MODULE_ENABLED + #include "stm32f4xx_hal_crc.h" +#endif /* HAL_CRC_MODULE_ENABLED */ + +#ifdef HAL_CRYP_MODULE_ENABLED + #include "stm32f4xx_hal_cryp.h" +#endif /* HAL_CRYP_MODULE_ENABLED */ + +#ifdef HAL_DMA2D_MODULE_ENABLED + #include "stm32f4xx_hal_dma2d.h" +#endif /* HAL_DMA2D_MODULE_ENABLED */ + +#ifdef HAL_DAC_MODULE_ENABLED + #include "stm32f4xx_hal_dac.h" +#endif /* HAL_DAC_MODULE_ENABLED */ + +#ifdef HAL_DCMI_MODULE_ENABLED + #include "stm32f4xx_hal_dcmi.h" +#endif /* HAL_DCMI_MODULE_ENABLED */ + +#ifdef HAL_ETH_MODULE_ENABLED + #include "stm32f4xx_hal_eth.h" +#endif /* HAL_ETH_MODULE_ENABLED */ + +#ifdef HAL_FLASH_MODULE_ENABLED + #include "stm32f4xx_hal_flash.h" +#endif /* HAL_FLASH_MODULE_ENABLED */ + +#ifdef HAL_SRAM_MODULE_ENABLED + #include "stm32f4xx_hal_sram.h" +#endif /* HAL_SRAM_MODULE_ENABLED */ + +#ifdef HAL_NOR_MODULE_ENABLED + #include "stm32f4xx_hal_nor.h" +#endif /* HAL_NOR_MODULE_ENABLED */ + +#ifdef HAL_NAND_MODULE_ENABLED + #include "stm32f4xx_hal_nand.h" +#endif /* HAL_NAND_MODULE_ENABLED */ + +#ifdef HAL_PCCARD_MODULE_ENABLED + #include "stm32f4xx_hal_pccard.h" +#endif /* HAL_PCCARD_MODULE_ENABLED */ + +#ifdef HAL_SDRAM_MODULE_ENABLED + #include "stm32f4xx_hal_sdram.h" +#endif /* HAL_SDRAM_MODULE_ENABLED */ + +#ifdef HAL_HASH_MODULE_ENABLED + #include "stm32f4xx_hal_hash.h" +#endif /* HAL_HASH_MODULE_ENABLED */ + +#ifdef HAL_I2C_MODULE_ENABLED + #include "stm32f4xx_hal_i2c.h" +#endif /* HAL_I2C_MODULE_ENABLED */ + +#ifdef HAL_SMBUS_MODULE_ENABLED + #include "stm32f4xx_hal_smbus.h" +#endif /* HAL_SMBUS_MODULE_ENABLED */ + +#ifdef HAL_I2S_MODULE_ENABLED + #include "stm32f4xx_hal_i2s.h" +#endif /* HAL_I2S_MODULE_ENABLED */ + +#ifdef HAL_IWDG_MODULE_ENABLED + #include "stm32f4xx_hal_iwdg.h" +#endif /* HAL_IWDG_MODULE_ENABLED */ + +#ifdef HAL_LTDC_MODULE_ENABLED + #include "stm32f4xx_hal_ltdc.h" +#endif /* HAL_LTDC_MODULE_ENABLED */ + +#ifdef HAL_PWR_MODULE_ENABLED + #include "stm32f4xx_hal_pwr.h" +#endif /* HAL_PWR_MODULE_ENABLED */ + +#ifdef HAL_RNG_MODULE_ENABLED + #include "stm32f4xx_hal_rng.h" +#endif /* HAL_RNG_MODULE_ENABLED */ + +#ifdef HAL_RTC_MODULE_ENABLED + #include "stm32f4xx_hal_rtc.h" +#endif /* HAL_RTC_MODULE_ENABLED */ + +#ifdef HAL_SAI_MODULE_ENABLED + #include "stm32f4xx_hal_sai.h" +#endif /* HAL_SAI_MODULE_ENABLED */ + +#ifdef HAL_SD_MODULE_ENABLED + #include "stm32f4xx_hal_sd.h" +#endif /* HAL_SD_MODULE_ENABLED */ + +#ifdef HAL_SPI_MODULE_ENABLED + #include "stm32f4xx_hal_spi.h" +#endif /* HAL_SPI_MODULE_ENABLED */ + +#ifdef HAL_TIM_MODULE_ENABLED + #include "stm32f4xx_hal_tim.h" +#endif /* HAL_TIM_MODULE_ENABLED */ + +#ifdef HAL_UART_MODULE_ENABLED + #include "stm32f4xx_hal_uart.h" +#endif /* HAL_UART_MODULE_ENABLED */ + +#ifdef HAL_USART_MODULE_ENABLED + #include "stm32f4xx_hal_usart.h" +#endif /* HAL_USART_MODULE_ENABLED */ + +#ifdef HAL_IRDA_MODULE_ENABLED + #include "stm32f4xx_hal_irda.h" +#endif /* HAL_IRDA_MODULE_ENABLED */ + +#ifdef HAL_SMARTCARD_MODULE_ENABLED + #include "stm32f4xx_hal_smartcard.h" +#endif /* HAL_SMARTCARD_MODULE_ENABLED */ + +#ifdef HAL_WWDG_MODULE_ENABLED + #include "stm32f4xx_hal_wwdg.h" +#endif /* HAL_WWDG_MODULE_ENABLED */ + +#ifdef HAL_PCD_MODULE_ENABLED + #include "stm32f4xx_hal_pcd.h" +#endif /* HAL_PCD_MODULE_ENABLED */ + +#ifdef HAL_HCD_MODULE_ENABLED + #include "stm32f4xx_hal_hcd.h" +#endif /* HAL_HCD_MODULE_ENABLED */ + +#ifdef HAL_DSI_MODULE_ENABLED + #include "stm32f4xx_hal_dsi.h" +#endif /* HAL_DSI_MODULE_ENABLED */ + +#ifdef HAL_QSPI_MODULE_ENABLED + #include "stm32f4xx_hal_qspi.h" +#endif /* HAL_QSPI_MODULE_ENABLED */ + +#ifdef HAL_CEC_MODULE_ENABLED + #include "stm32f4xx_hal_cec.h" +#endif /* HAL_CEC_MODULE_ENABLED */ + +#ifdef HAL_FMPI2C_MODULE_ENABLED + #include "stm32f4xx_hal_fmpi2c.h" +#endif /* HAL_FMPI2C_MODULE_ENABLED */ + +#ifdef HAL_SPDIFRX_MODULE_ENABLED + #include "stm32f4xx_hal_spdifrx.h" +#endif /* HAL_SPDIFRX_MODULE_ENABLED */ + +#ifdef HAL_DFSDM_MODULE_ENABLED + #include "stm32f4xx_hal_dfsdm.h" +#endif /* HAL_DFSDM_MODULE_ENABLED */ + +#ifdef HAL_LPTIM_MODULE_ENABLED + #include "stm32f4xx_hal_lptim.h" +#endif /* HAL_LPTIM_MODULE_ENABLED */ + +#ifdef HAL_MMC_MODULE_ENABLED + #include "stm32f4xx_hal_mmc.h" +#endif /* HAL_MMC_MODULE_ENABLED */ + +/* Exported macro ------------------------------------------------------------*/ +#ifdef USE_FULL_ASSERT +/** + * @brief The assert_param macro is used for function's parameters check. + * @param expr If expr is false, it calls assert_failed function + * which reports the name of the source file and the source + * line number of the call that failed. + * If expr is true, it returns no value. + * @retval None + */ + #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__)) +/* Exported functions ------------------------------------------------------- */ + void assert_failed(uint8_t *file, uint32_t line); +#else + #define assert_param(expr) ((void)0U) +#endif /* USE_FULL_ASSERT */ + + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32F4xx_HAL_CONF_H */ + + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ diff --git a/buildroot/share/PlatformIO/variants/MARLIN_MKS_SKIPR_V1/ldscript.ld b/buildroot/share/PlatformIO/variants/MARLIN_MKS_SKIPR_V1/ldscript.ld new file mode 100644 index 0000000000..df1ed1581a --- /dev/null +++ b/buildroot/share/PlatformIO/variants/MARLIN_MKS_SKIPR_V1/ldscript.ld @@ -0,0 +1,203 @@ +/* +****************************************************************************** +** +** File : LinkerScript.ld +** +** Abstract : Linker script for STM32F4x7Vx Device with +** 512/1024KByte FLASH, 192KByte RAM +** +** Set heap size, stack size and stack location according +** to application requirements. +** +** Set memory bank area and size if external memory is used. +** +** Target : STMicroelectronics STM32 +** +** Distribution: The file is distributed “as is,” without any warranty +** of any kind. +** +***************************************************************************** +** @attention +** +** Copyright (c) 2019 STMicroelectronics +** +** Redistribution and use in source and binary forms, with or without modification, +** are permitted provided that the following conditions are met: +** 1. Redistributions of source code must retain the above copyright notice, +** this list of conditions and the following disclaimer. +** 2. Redistributions in binary form must reproduce the above copyright notice, +** this list of conditions and the following disclaimer in the documentation +** and/or other materials provided with the distribution. +** 3. Neither the name of STMicroelectronics nor the names of its contributors +** may be used to endorse or promote products derived from this software +** without specific prior written permission. +** +** THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" +** AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE +** IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE +** DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE +** FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL +** DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR +** SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER +** CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, +** OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE +** OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. +** +***************************************************************************** +*/ + +/* Entry Point */ +ENTRY(Reset_Handler) + +/* Highest address of the user mode stack */ +_estack = 0x20000000 + LD_MAX_DATA_SIZE; /* end of RAM */ +/* Generate a link error if heap and stack don't fit into RAM */ +_Min_Heap_Size = 0x200; /* required amount of heap */ +_Min_Stack_Size = 0x400; /* required amount of stack */ + +/* Specify the memory areas */ +MEMORY +{ +RAM (xrw) : ORIGIN = 0x20000000, LENGTH = LD_MAX_DATA_SIZE +CCMRAM (rw) : ORIGIN = 0x10000000, LENGTH = 64K +FLASH (rx) : ORIGIN = 0x08000000 + LD_FLASH_OFFSET, LENGTH = LD_MAX_SIZE - LD_FLASH_OFFSET +} + +/* Define output sections */ +SECTIONS +{ + /* The startup code goes first into FLASH */ + .isr_vector : + { + . = ALIGN(4); + KEEP(*(.isr_vector)) /* Startup code */ + . = ALIGN(4); + } >FLASH + + /* The program code and other data goes into FLASH */ + .text : + { + . = ALIGN(4); + *(.text) /* .text sections (code) */ + *(.text*) /* .text* sections (code) */ + *(.glue_7) /* glue arm to thumb code */ + *(.glue_7t) /* glue thumb to arm code */ + *(.eh_frame) + + KEEP (*(.init)) + KEEP (*(.fini)) + + . = ALIGN(4); + _etext = .; /* define a global symbols at end of code */ + } >FLASH + + /* Constant data goes into FLASH */ + .rodata : + { + . = ALIGN(4); + *(.rodata) /* .rodata sections (constants, strings, etc.) */ + *(.rodata*) /* .rodata* sections (constants, strings, etc.) */ + . = ALIGN(4); + } >FLASH + + .ARM.extab : { *(.ARM.extab* .gnu.linkonce.armextab.*) } >FLASH + .ARM : { + __exidx_start = .; + *(.ARM.exidx*) + __exidx_end = .; + } >FLASH + + .preinit_array : + { + PROVIDE_HIDDEN (__preinit_array_start = .); + KEEP (*(.preinit_array*)) + PROVIDE_HIDDEN (__preinit_array_end = .); + } >FLASH + .init_array : + { + PROVIDE_HIDDEN (__init_array_start = .); + KEEP (*(SORT(.init_array.*))) + KEEP (*(.init_array*)) + PROVIDE_HIDDEN (__init_array_end = .); + } >FLASH + .fini_array : + { + PROVIDE_HIDDEN (__fini_array_start = .); + KEEP (*(SORT(.fini_array.*))) + KEEP (*(.fini_array*)) + PROVIDE_HIDDEN (__fini_array_end = .); + } >FLASH + + /* used by the startup to initialize data */ + _sidata = LOADADDR(.data); + + /* Initialized data sections goes into RAM, load LMA copy after code */ + .data : + { + . = ALIGN(4); + _sdata = .; /* create a global symbol at data start */ + *(.data) /* .data sections */ + *(.data*) /* .data* sections */ + + . = ALIGN(4); + _edata = .; /* define a global symbol at data end */ + } >RAM AT> FLASH + + _siccmram = LOADADDR(.ccmram); + + /* CCM-RAM section + * + * IMPORTANT NOTE! + * If initialized variables will be placed in this section, + * the startup code needs to be modified to copy the init-values. + */ + .ccmram : + { + . = ALIGN(4); + _sccmram = .; /* create a global symbol at ccmram start */ + *(.ccmram) + *(.ccmram*) + + . = ALIGN(4); + _eccmram = .; /* create a global symbol at ccmram end */ + } >CCMRAM AT> FLASH + + + /* Uninitialized data section */ + . = ALIGN(4); + .bss : + { + /* This is used by the startup in order to initialize the .bss section */ + _sbss = .; /* define a global symbol at bss start */ + __bss_start__ = _sbss; + *(.bss) + *(.bss*) + *(COMMON) + + . = ALIGN(4); + _ebss = .; /* define a global symbol at bss end */ + __bss_end__ = _ebss; + } >RAM + + /* User_heap_stack section, used to check that there is enough RAM left */ + ._user_heap_stack : + { + . = ALIGN(8); + PROVIDE ( end = . ); + PROVIDE ( _end = . ); + . = . + _Min_Heap_Size; + . = . + _Min_Stack_Size; + . = ALIGN(8); + } >RAM + + + /* Remove information from the standard libraries */ + /DISCARD/ : + { + libc.a ( * ) + libm.a ( * ) + libgcc.a ( * ) + } + + .ARM.attributes 0 : { *(.ARM.attributes) } +} diff --git a/buildroot/share/PlatformIO/variants/MARLIN_MKS_SKIPR_V1/variant.cpp b/buildroot/share/PlatformIO/variants/MARLIN_MKS_SKIPR_V1/variant.cpp new file mode 100644 index 0000000000..00c7a90db3 --- /dev/null +++ b/buildroot/share/PlatformIO/variants/MARLIN_MKS_SKIPR_V1/variant.cpp @@ -0,0 +1,288 @@ +/* + ******************************************************************************* + * Copyright (c) 2017, STMicroelectronics + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + ******************************************************************************* + */ + +#include "pins_arduino.h" + +#ifdef __cplusplus +extern "C" { +#endif + + +// Digital PinName array +const PinName digitalPin[] = { + PA_0, // Digital pin 0 + PA_1, // Digital pin 1 + PA_2, // Digital pin 2 + PA_3, // Digital pin 3 + PA_4, // Digital pin 4 + PA_5, // Digital pin 5 + PA_6, // Digital pin 6 + PA_7, // Digital pin 7 + PA_8, // Digital pin 8 + PA_9, // Digital pin 9 + PA_10, // Digital pin 10 + PA_11, // Digital pin 11 + PA_12, // Digital pin 12 + PA_13, // Digital pin 13 + PA_14, // Digital pin 14 + PA_15, // Digital pin 15 + + PB_0, // Digital pin 16 + PB_1, // Digital pin 17 + PB_2, // Digital pin 18 + PB_3, // Digital pin 19 + PB_4, // Digital pin 20 + PB_5, // Digital pin 21 + PB_6, // Digital pin 22 + PB_7, // Digital pin 23 + PB_8, // Digital pin 24 + PB_9, // Digital pin 25 + PB_10, // Digital pin 26 + PB_11, // Digital pin 27 + PB_12, // Digital pin 28 + PB_13, // Digital pin 29 + PB_14, // Digital pin 30 + PB_15, // Digital pin 31 + + PC_0, // Digital pin 32 + PC_1, // Digital pin 33 + PC_2, // Digital pin 34 + PC_3, // Digital pin 35 + PC_4, // Digital pin 36 + PC_5, // Digital pin 37 + PC_6, // Digital pin 38 + PC_7, // Digital pin 39 + PC_8, // Digital pin 40 + PC_9, // Digital pin 41 + PC_10, // Digital pin 42 + PC_11, // Digital pin 43 + PC_12, // Digital pin 44 + PC_13, // Digital pin 45 + PC_14, // Digital pin 46 + PC_15, // Digital pin 47 + + PD_0, // Digital pin 48 + PD_1, // Digital pin 49 + PD_2, // Digital pin 50 + PD_3, // Digital pin 51 + PD_4, // Digital pin 52 + PD_5, // Digital pin 53 + PD_6, // Digital pin 54 + PD_7, // Digital pin 55 + PD_8, // Digital pin 56 + PD_9, // Digital pin 57 + PD_10, // Digital pin 58 + PD_11, // Digital pin 59 + PD_12, // Digital pin 60 + PD_13, // Digital pin 61 + PD_14, // Digital pin 62 + PD_15, // Digital pin 63 + + PE_0, // Digital pin 64 + PE_1, // Digital pin 65 + PE_2, // Digital pin 66 + PE_3, // Digital pin 67 + PE_4, // Digital pin 68 + PE_5, // Digital pin 69 + PE_6, // Digital pin 70 + PE_7, // Digital pin 71 + PE_8, // Digital pin 72 + PE_9, // Digital pin 73 + PE_10, // Digital pin 74 + PE_11, // Digital pin 75 + PE_12, // Digital pin 76 + PE_13, // Digital pin 77 + PE_14, // Digital pin 78 + PE_15, // Digital pin 79 + + PH_0, // Digital pin 80, used by the external oscillator + PH_1 // Digital pin 81, used by the external oscillator +}; + +// Analog (Ax) pin number array +const uint32_t analogInputPin[] = { + 0, // A0, PA0 + 1, // A1, PA1 + 2, // A2, PA2 + 3, // A3, PA3 + 4, // A4, PA4 + 5, // A5, PA5 + 6, // A6, PA6 + 7, // A7, PA7 + 16, // A8, PB0 + 17, // A9, PB1 + 32, // A10, PC0 + 33, // A11, PC1 + 34, // A12, PC2 + 35, // A13, PC3 + 36, // A14, PC4 + 37 // A15, PC5 +}; + +#ifdef __cplusplus +} +#endif + +// ---------------------------------------------------------------------------- + +#ifdef __cplusplus +extern "C" { +#endif + +/* + * @brief Configures the System clock source, PLL Multiplier and Divider factors, + * AHB/APBx prescalers and Flash settings + * @note This function should be called only once the RCC clock configuration + * is reset to the default reset state (done in SystemInit() function). + * @param None + * @retval None + */ + +/******************************************************************************/ +/* PLL (clocked by HSE) used as System clock source */ +/******************************************************************************/ +static uint8_t SetSysClock_PLL_HSE(uint8_t bypass) +{ + RCC_OscInitTypeDef RCC_OscInitStruct; + RCC_ClkInitTypeDef RCC_ClkInitStruct; + + /* The voltage scaling allows optimizing the power consumption when the device is + clocked below the maximum system frequency, to update the voltage scaling value + regarding system frequency refer to product datasheet. */ + __HAL_RCC_PWR_CLK_ENABLE(); + __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1); + + // Enable HSE oscillator and activate PLL with HSE as source + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; + if (bypass == 0) { + RCC_OscInitStruct.HSEState = RCC_HSE_ON; // External 8 MHz xtal on OSC_IN/OSC_OUT + } else { + RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS; // External 8 MHz clock on OSC_IN + } + + RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; + RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE; + RCC_OscInitStruct.PLL.PLLM = HSE_VALUE / 1000000L; // Expects an 8 MHz external clock by default. Redefine HSE_VALUE if not + RCC_OscInitStruct.PLL.PLLN = 336; // VCO output clock = 336 MHz (1 MHz * 336) + RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 168 MHz (336 MHz / 2) + RCC_OscInitStruct.PLL.PLLQ = 7; + if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) { + return 0; // FAIL + } + + // Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers + RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2; + RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; + RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 168 MHz + RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // 42 MHz + RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; // 84 MHz + if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK) { + return 0; // FAIL + } + + /* Output clock on MCO1 pin(PA8) for debugging purpose */ + /* + if (bypass == 0) + HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_2); // 4 MHz + else + HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSE, RCC_MCODIV_1); // 8 MHz + */ + + return 1; // OK +} + +/******************************************************************************/ +/* PLL (clocked by HSI) used as System clock source */ +/******************************************************************************/ +uint8_t SetSysClock_PLL_HSI(void) +{ + RCC_OscInitTypeDef RCC_OscInitStruct; + RCC_ClkInitTypeDef RCC_ClkInitStruct; + + /* The voltage scaling allows optimizing the power consumption when the device is + clocked below the maximum system frequency, to update the voltage scaling value + regarding system frequency refer to product datasheet. */ + __HAL_RCC_PWR_CLK_ENABLE(); + __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1); + + // Enable HSI oscillator and activate PLL with HSI as source + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_HSE; + RCC_OscInitStruct.HSIState = RCC_HSI_ON; + RCC_OscInitStruct.HSEState = RCC_HSE_OFF; + RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT; + RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON; + RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI; + RCC_OscInitStruct.PLL.PLLM = 16; // VCO input clock = 1 MHz (16 MHz / 16) + RCC_OscInitStruct.PLL.PLLN = 336; // VCO output clock = 336 MHz (1 MHz * 336) + RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; // PLLCLK = 168 MHz (336 MHz / 2) + RCC_OscInitStruct.PLL.PLLQ = 7; + if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) { + return 0; // FAIL + } + + /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */ + RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2); + RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK; + RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; // 168 MHz + RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4; // 42 MHz + RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2; // 84 MHz + if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK) { + return 0; // FAIL + } + + /* Output clock on MCO1 pin(PA8) for debugging purpose */ + //HAL_RCC_MCOConfig(RCC_MCO1, RCC_MCO1SOURCE_HSI, RCC_MCODIV_1); // 16 MHz + + return 1; // OK +} + +WEAK void SystemClock_Config(void) +{ + /* 1- If fail try to start with HSE and external xtal */ + if (SetSysClock_PLL_HSE(0) == 0) { + /* 2- Try to start with HSE and external clock */ + if (SetSysClock_PLL_HSE(1) == 0) { + /* 3- If fail start with HSI clock */ + if (SetSysClock_PLL_HSI() == 0) { + Error_Handler(); + } + } + } + + /* Ensure CCM RAM clock is enabled */ + __HAL_RCC_CCMDATARAMEN_CLK_ENABLE(); + + /* Output clock on MCO2 pin(PC9) for debugging purpose */ + //HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_4); +} + +#ifdef __cplusplus +} +#endif diff --git a/buildroot/share/PlatformIO/variants/MARLIN_MKS_SKIPR_V1/variant.h b/buildroot/share/PlatformIO/variants/MARLIN_MKS_SKIPR_V1/variant.h new file mode 100644 index 0000000000..dcc8c49395 --- /dev/null +++ b/buildroot/share/PlatformIO/variants/MARLIN_MKS_SKIPR_V1/variant.h @@ -0,0 +1,196 @@ +/* + ******************************************************************************* + * Copyright (c) 2017, STMicroelectronics + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + ******************************************************************************* + */ +#pragma once + +#ifdef __cplusplus +extern "C" { +#endif // __cplusplus +// +/*---------------------------------------------------------------------------- + * Pins + *----------------------------------------------------------------------------*/ + // | DIGITAL | ANALOG IN | ANALOG OUT | UART/USART | TWI | SPI | SPECIAL | + // |---------|------------|------------|-----------------------|----------------------|-----------------------------------|-----------| +#define PA0 PIN_A0 // | 0 | A0 (ADC1) | | UART4_TX | | | | +#define PA1 PIN_A1 // | 1 | A1 (ADC1) | | UART4_RX | | | | +#define PA2 PIN_A2 // | 2 | A2 (ADC1) | | USART2_TX | | | | +#define PA3 PIN_A3 // | 3 | A3 (ADC1) | | USART2_RX | | | | +#define PA4 PIN_A4 // | 4 | A4 (ADC1) | DAC_OUT1 | | | SPI1_SS, (SPI3_SS) | | +#define PA5 PIN_A5 // | 5 | A5 (ADC1) | DAC_OUT2 | | | SPI1_SCK | | +#define PA6 PIN_A6 // | 6 | A6 (ADC1) | | | | SPI1_MISO | | +#define PA7 PIN_A7 // | 7 | A7 (ADC1) | | | | SPI1_MOSI | | +#define PA8 8 // | 8 | | | | TWI3_SCL | | | +#define PA9 9 // | 9 | | | USART1_TX | | | | +#define PA10 10 // | 10 | | | USART1_RX | | | | +#define PA11 11 // | 11 | | | | | | | +#define PA12 12 // | 12 | | | | | | | +#define PA13 13 // | 13 | | | | | | SWD_SWDIO | +#define PA14 14 // | 14 | | | | | | SWD_SWCLK | +#define PA15 15 // | 15 | | | | | SPI3_SS, (SPI1_SS) | | + // |---------|------------|------------|-----------------------|----------------------|-----------------------------------|-----------| +#define PB0 PIN_A8 // | 16 | A8 (ADC1) | | | | | | +#define PB1 PIN_A9 // | 17 | A9 (ADC1) | | | | | | +#define PB2 18 // | 18 | | | | | | BOOT1 | +#define PB3 19 // | 19 | | | | | SPI3_SCK, (SPI1_SCK) | | +#define PB4 20 // | 20 | | | | | SPI3_MISO, (SPI1_MISO) | | +#define PB5 21 // | 21 | | | | | SPI3_MOSI, (SPI1_MOSI) | | +#define PB6 22 // | 22 | | | USART1_TX | TWI1_SCL | | | +#define PB7 23 // | 23 | | | USART1_RX | TWI1_SDA | | | +#define PB8 24 // | 24 | | | | TWI1_SCL | | | +#define PB9 25 // | 25 | | | | TWI1_SDA | SPI2_SS | | +#define PB10 26 // | 26 | | | USART3_TX, (UART4_TX) | TWI2_SCL | SPI2_SCK | | +#define PB11 27 // | 27 | | | USART3_RX | TWI2_SDA | | | +#define PB12 28 // | 28 | | | | | SPI2_SS | | +#define PB13 29 // | 29 | | | | | SPI2_SCK | | +#define PB14 30 // | 30 | | | | | SPI2_MISO | | +#define PB15 31 // | 31 | | | | | SPI2_MOSI | | + // |---------|------------|------------|-----------------------|----------------------|-----------------------------------|-----------| +#define PC0 PIN_A10 // | 32 | A10 (ADC1) | | | | | | +#define PC1 PIN_A11 // | 33 | A11 (ADC1) | | | | | | +#define PC2 PIN_A12 // | 34 | A12 (ADC1) | | | | SPI2_MISO | | +#define PC3 PIN_A13 // | 35 | A13 (ADC1) | | | | SPI2_MOSI | | +#define PC4 PIN_A14 // | 36 | A14 (ADC1) | | | | | | +#define PC5 PIN_A15 // | 37 | A15 (ADC1) | | USART3_RX | | | | +#define PC6 38 // | 38 | | | USART6_TX | | | | +#define PC7 39 // | 39 | | | USART6_RX | | | | +#define PC8 40 // | 40 | | | | | | | +#define PC9 41 // | 41 | | | USART3_TX | TWI3_SDA | | | +#define PC10 42 // | 42 | | | | | SPI3_SCK | | +#define PC11 43 // | 43 | | | USART3_RX, (UART4_RX) | | SPI3_MISO | | +#define PC12 44 // | 44 | | | UART5_TX | | SPI3_MOSI | | +#define PC13 45 // | 45 | | | | | | | +#define PC14 46 // | 46 | | | | | | OSC32_IN | +#define PC15 47 // | 47 | | | | | | OSC32_OUT | + // |---------|------------|------------|-----------------------|----------------------|-----------------------------------|-----------| +#define PD0 48 // | 48 | | | | | | | +#define PD1 49 // | 49 | | | | | | | +#define PD2 50 // | 50 | | | UART5_RX | | | | +#define PD3 51 // | 51 | | | | | | | +#define PD4 52 // | 52 | | | | | | | +#define PD5 53 // | 53 | | | USART2_TX | | | | +#define PD6 54 // | 54 | | | USART2_RX | | | | +#define PD7 55 // | 55 | | | | | | | +#define PD8 56 // | 56 | | | USART3_TX | | | | +#define PD9 57 // | 57 | | | USART3_RX | | | | +#define PD10 58 // | 58 | | | | | | | +#define PD11 59 // | 59 | | | | | | | +#define PD12 60 // | 60 | | | | | | | +#define PD13 61 // | 61 | | | | | | | +#define PD14 62 // | 62 | | | | | | | +#define PD15 63 // | 63 | | | | | | | + // |---------|------------|------------|-----------------------|----------------------|-----------------------------------|-----------| +#define PE0 64 // | 64 | | | | | | | +#define PE1 65 // | 65 | | | | | | | +#define PE2 66 // | 66 | | | | | | | +#define PE3 67 // | 67 | | | | | | | +#define PE4 68 // | 68 | | | | | | | +#define PE5 69 // | 69 | | | | | | | +#define PE6 70 // | 70 | | | | | | | +#define PE7 71 // | 71 | | | | | | | +#define PE8 72 // | 72 | | | | | | | +#define PE9 73 // | 73 | | | | | | | +#define PE10 74 // | 74 | | | | | | | +#define PE11 75 // | 75 | | | | | | | +#define PE12 76 // | 76 | | | | | | | +#define PE13 77 // | 77 | | | | | | | +#define PE14 78 // | 78 | | | | | | | +#define PE15 79 // | 79 | | | | | | | + // |---------|------------|------------|-----------------------|----------------------|-----------------------------------|-----------| +#define PH0 80 // | 80 | | | | | | OSC_IN | +#define PH1 81 // | 81 | | | | | | OSC_OUT | + // |---------|------------|------------|-----------------------|----------------------|-----------------------------------|-----------| + +// This must be a literal +#define NUM_DIGITAL_PINS 82 +#define NUM_ANALOG_INPUTS 16 + +// Below SPI and I2C definitions already done in the core +// Could be redefined here if differs from the default one +// SPI Definitions +#define PIN_SPI_SS PC9 +#define PIN_SPI_SCK PC10 +#define PIN_SPI_MISO PC11 +#define PIN_SPI_MOSI PC12 + +// I2C Definitions +#define PIN_WIRE_SCL PB8 +#define PIN_WIRE_SDA PB9 + +// Timer Definitions +// Do not use timer used by PWM pins when possible. See PinMap_PWM in PeripheralPins.c +// TIM1 = HEATER0, HEATER1, [SERVO] +// TIM2 = FAN1, FAN2, [BEEPER] +// TIM4 = HEATER_BED +// TIM5 = HEATER2, FAN0 +// Uses default for STM32F4xx STEP_TIMER 6 and TEMP_TIMER 14 +#define TIMER_SERVO TIM1 // TIMER_SERVO must be defined in this file +#define TIMER_TONE TIM2 // TIMER_TONE must be defined in this file +#define TIMER_SERIAL TIM3 // TIMER_SERIAL must be defined in this file + +// USART1 (direct to RK3328 SoC) +#define ENABLE_HWSERIAL1 +#define PIN_SERIAL1_TX PA9 +#define PIN_SERIAL1_RX PA10 + +// USART3 connector +#define ENABLE_HWSERIAL3 +#define PIN_SERIAL3_TX PB10 +#define PIN_SERIAL3_RX PB11 + +#ifdef __cplusplus +} // extern "C" +#endif +/*---------------------------------------------------------------------------- + * Arduino objects - C++ only + *----------------------------------------------------------------------------*/ + +#ifdef __cplusplus +// These serial port names are intended to allow libraries and architecture-neutral +// sketches to automatically default to the correct port name for a particular type +// of use. For example, a GPS module would normally connect to SERIAL_PORT_HARDWARE_OPEN, +// the first hardware serial port whose RX/TX pins are not dedicated to another use. +// +// SERIAL_PORT_MONITOR Port which normally prints to the Arduino Serial Monitor +// +// SERIAL_PORT_USBVIRTUAL Port which is USB virtual serial +// +// SERIAL_PORT_LINUXBRIDGE Port which connects to a Linux system via Bridge library +// +// SERIAL_PORT_HARDWARE Hardware serial port, physical RX & TX pins. +// +// SERIAL_PORT_HARDWARE_OPEN Hardware serial ports which are open for use. Their RX & TX +// pins are NOT connected to anything by default. +#define SERIAL_PORT_MONITOR Serial1 +#define SERIAL_PORT_USBVIRTUAL SerialUSB +#define SERIAL_PORT_HARDWARE Serial1 +#define SERIAL_PORT_HARDWARE1 Serial3 +#define SERIAL_PORT_HARDWARE_OPEN Serial1 +#define SERIAL_PORT_HARDWARE_OPEN1 Serial3 +#endif diff --git a/buildroot/share/PlatformIO/variants/MARLIN_TH3D_EZBOARD_V2/hal_conf_extra.h b/buildroot/share/PlatformIO/variants/MARLIN_TH3D_EZBOARD_V2/hal_conf_extra.h index a5961a488b..8a04b8be10 100755 --- a/buildroot/share/PlatformIO/variants/MARLIN_TH3D_EZBOARD_V2/hal_conf_extra.h +++ b/buildroot/share/PlatformIO/variants/MARLIN_TH3D_EZBOARD_V2/hal_conf_extra.h @@ -8,8 +8,8 @@ ****************************************************************************** * @attention * - *

© Copyright (c) 2017 STMicroelectronics. - * All rights reserved.

+ * Copyright (c) 2017 STMicroelectronics. + * All rights reserved. * * This software component is licensed by ST under BSD 3-Clause license, * the "License"; You may not use this file except in compliance with the diff --git a/buildroot/share/PlatformIO/variants/MARLIN_TH3D_EZBOARD_V2/ldscript.ld b/buildroot/share/PlatformIO/variants/MARLIN_TH3D_EZBOARD_V2/ldscript.ld index e07c5e4ace..55ae9227db 100644 --- a/buildroot/share/PlatformIO/variants/MARLIN_TH3D_EZBOARD_V2/ldscript.ld +++ b/buildroot/share/PlatformIO/variants/MARLIN_TH3D_EZBOARD_V2/ldscript.ld @@ -20,7 +20,7 @@ ***************************************************************************** ** @attention ** -**

© COPYRIGHT(c) 2019 STMicroelectronics

+** Copyright (c) 2019 STMicroelectronics ** ** Redistribution and use in source and binary forms, with or without modification, ** are permitted provided that the following conditions are met: diff --git a/buildroot/share/git/mfinfo b/buildroot/share/git/mfinfo index 3f183b8fd8..c74e48650c 100755 --- a/buildroot/share/git/mfinfo +++ b/buildroot/share/git/mfinfo @@ -56,7 +56,7 @@ done case "$REPO" in Marlin ) TARG=bugfix-2.1.x ; ((INDEX == 1)) && TARG=bugfix-1.1.x ; [[ $BRANCH =~ ^[12]$ ]] && USAGE=1 ;; - Configurations ) TARG=import-2.0.x ;; + Configurations ) TARG=import-2.1.x ;; MarlinDocumentation ) TARG=master ;; AutoBuildMarlin ) TARG=master ;; esac diff --git a/buildroot/share/scripts/config-labels.py b/buildroot/share/scripts/config-labels.py index b721baf441..b571a434b7 100755 --- a/buildroot/share/scripts/config-labels.py +++ b/buildroot/share/scripts/config-labels.py @@ -47,150 +47,150 @@ different_out_dir = not (output_examples_dir == input_examples_dir) #---------------------------------------------- def process_file(subdir: str, filename: str): #---------------------------------------------- - global filenum - filenum += 1 + global filenum + filenum += 1 - print(str(filenum) + ' ' + filename + ': ' + subdir) + print(str(filenum) + ' ' + filename + ': ' + subdir) - def_line = (def_macro_name + ' "' + subdir.replace('\\', '/') + '"') + def_line = (def_macro_name + ' "' + subdir.replace('\\', '/') + '"') - #------------------------ - # Read file - #------------------------ - lines = [] - infilepath = Path(input_examples_dir, subdir, filename) - try: - # UTF-8 because some files contain unicode chars - with infilepath.open('rt', encoding="utf-8") as infile: - lines = infile.readlines() + #------------------------ + # Read file + #------------------------ + lines = [] + infilepath = Path(input_examples_dir, subdir, filename) + try: + # UTF-8 because some files contain unicode chars + with infilepath.open('rt', encoding="utf-8") as infile: + lines = infile.readlines() - except Exception as e: - print('Failed to read file: ' + str(e) ) - raise Exception + except Exception as e: + print('Failed to read file: ' + str(e) ) + raise Exception - lines = [line.rstrip('\r\n') for line in lines] + lines = [line.rstrip('\r\n') for line in lines] - #------------------------ - # Process lines - #------------------------ - file_modified = False + #------------------------ + # Process lines + #------------------------ + file_modified = False - # region state machine - # -1 = before pragma once; - # 0 = region to place define; - # 1 = past region to place define - region = -1 + # region state machine + # -1 = before pragma once; + # 0 = region to place define; + # 1 = past region to place define + region = -1 - outlines = [] - for line in lines: - outline = line + outlines = [] + for line in lines: + outline = line - if (region == -1) and (def_macro_name in line): - outline = None - file_modified = True + if (region == -1) and (def_macro_name in line): + outline = None + file_modified = True - elif (region == -1) and ('pragma once' in line): - region = 0 + elif (region == -1) and ('pragma once' in line): + region = 0 - elif (region == 0): - if (line.strip() == ''): - pass - elif (def_macro_name in line): - region = 1 - if line == def_line: # leave it as is - pass - else: - outline = def_line - file_modified = True - else: # some other string - outlines.append(def_line) - outlines.append('') - region = 1 - file_modified = True + elif (region == 0): + if (line.strip() == ''): + pass + elif (def_macro_name in line): + region = 1 + if line == def_line: # leave it as is + pass + else: + outline = def_line + file_modified = True + else: # some other string + outlines.append(def_line) + outlines.append('') + region = 1 + file_modified = True - elif (region == 1): - if (def_macro_name in line): - outline = None - file_modified = True - else: - pass + elif (region == 1): + if (def_macro_name in line): + outline = None + file_modified = True + else: + pass - # end if - if outline is not None: - outlines.append(outline) - # end for + # end if + if outline is not None: + outlines.append(outline) + # end for - #------------------------- - # Output file - #------------------------- - outdir = Path(output_examples_dir, subdir) - outfilepath = outdir / filename + #------------------------- + # Output file + #------------------------- + outdir = Path(output_examples_dir, subdir) + outfilepath = outdir / filename - if file_modified: - # Note: no need to create output dirs, as the initial copy_tree - # will do that. + if file_modified: + # Note: no need to create output dirs, as the initial copy_tree + # will do that. - print(' writing ' + str(outfilepath)) - try: - # Preserve unicode chars; Avoid CR-LF on Windows. - with outfilepath.open("w", encoding="utf-8", newline='\n') as outfile: - outfile.write("\n".join(outlines) + "\n") + print(' writing ' + str(outfilepath)) + try: + # Preserve unicode chars; Avoid CR-LF on Windows. + with outfilepath.open("w", encoding="utf-8", newline='\n') as outfile: + outfile.write("\n".join(outlines) + "\n") - except Exception as e: - print('Failed to write file: ' + str(e) ) - raise Exception - else: - print(' no change for ' + str(outfilepath)) + except Exception as e: + print('Failed to write file: ' + str(e) ) + raise Exception + else: + print(' no change for ' + str(outfilepath)) #---------- def main(): #---------- - global filenum - global input_examples_dir - global output_examples_dir - filenum = 0 + global filenum + global input_examples_dir + global output_examples_dir + filenum = 0 - #-------------------------------- - # Check for requirements - #-------------------------------- - input_examples_dir = input_examples_dir.strip() - input_examples_dir = input_examples_dir.rstrip('\\/') - output_examples_dir = output_examples_dir.strip() - output_examples_dir = output_examples_dir.rstrip('\\/') + #-------------------------------- + # Check for requirements + #-------------------------------- + input_examples_dir = input_examples_dir.strip() + input_examples_dir = input_examples_dir.rstrip('\\/') + output_examples_dir = output_examples_dir.strip() + output_examples_dir = output_examples_dir.rstrip('\\/') - for dir in (input_examples_dir, output_examples_dir): - if not Path(dir).exists(): - print('Directory not found: ' + dir) - sys.exit(1) + for dir in (input_examples_dir, output_examples_dir): + if not Path(dir).exists(): + print('Directory not found: ' + dir) + sys.exit(1) - #-------------------------------- - # Copy tree if necessary. - #-------------------------------- - # This includes files that are not otherwise included in the - # insertion of the define statement. - # - if different_out_dir: - print('Copying files to new directory: ' + output_examples_dir) - try: - copy_tree(input_examples_dir, output_examples_dir) - except Exception as e: - print('Failed to copy directory: ' + str(e) ) - raise Exception + #-------------------------------- + # Copy tree if necessary. + #-------------------------------- + # This includes files that are not otherwise included in the + # insertion of the define statement. + # + if different_out_dir: + print('Copying files to new directory: ' + output_examples_dir) + try: + copy_tree(input_examples_dir, output_examples_dir) + except Exception as e: + print('Failed to copy directory: ' + str(e) ) + raise Exception - #----------------------------- - # Find and process files - #----------------------------- - len_input_examples_dir = 1 + len(input_examples_dir) + #----------------------------- + # Find and process files + #----------------------------- + len_input_examples_dir = 1 + len(input_examples_dir) - for filename in files_to_mod: - input_path = Path(input_examples_dir) - filepathlist = input_path.rglob(filename) + for filename in files_to_mod: + input_path = Path(input_examples_dir) + filepathlist = input_path.rglob(filename) - for filepath in filepathlist: - fulldirpath = str(filepath.parent) - subdir = fulldirpath[len_input_examples_dir:] + for filepath in filepathlist: + fulldirpath = str(filepath.parent) + subdir = fulldirpath[len_input_examples_dir:] - process_file(subdir, filename) + process_file(subdir, filename) #============== print('--- Starting config-labels ---') diff --git a/buildroot/share/scripts/gen-tft-image.py b/buildroot/share/scripts/gen-tft-image.py index 9b7d19493e..f3786aef70 100644 --- a/buildroot/share/scripts/gen-tft-image.py +++ b/buildroot/share/scripts/gen-tft-image.py @@ -26,38 +26,38 @@ import sys,struct from PIL import Image def image2bin(image, output_file): - if output_file.endswith(('.c', '.cpp')): - f = open(output_file, 'wt') - is_cpp = True - f.write("const uint16_t image[%d] = {\n" % (image.size[1] * image.size[0])) - else: - f = open(output_file, 'wb') - is_cpp = False - pixs = image.load() - for y in range(image.size[1]): - for x in range(image.size[0]): - R = pixs[x, y][0] >> 3 - G = pixs[x, y][1] >> 2 - B = pixs[x, y][2] >> 3 - rgb = (R << 11) | (G << 5) | B - if is_cpp: - strHex = '0x{0:04X}, '.format(rgb) - f.write(strHex) - else: - f.write(struct.pack("B", (rgb & 0xFF))) - f.write(struct.pack("B", (rgb >> 8) & 0xFF)) - if is_cpp: - f.write("\n") - if is_cpp: - f.write("};\n") - f.close() + if output_file.endswith(('.c', '.cpp')): + f = open(output_file, 'wt') + is_cpp = True + f.write("const uint16_t image[%d] = {\n" % (image.size[1] * image.size[0])) + else: + f = open(output_file, 'wb') + is_cpp = False + pixs = image.load() + for y in range(image.size[1]): + for x in range(image.size[0]): + R = pixs[x, y][0] >> 3 + G = pixs[x, y][1] >> 2 + B = pixs[x, y][2] >> 3 + rgb = (R << 11) | (G << 5) | B + if is_cpp: + strHex = '0x{0:04X}, '.format(rgb) + f.write(strHex) + else: + f.write(struct.pack("B", (rgb & 0xFF))) + f.write(struct.pack("B", (rgb >> 8) & 0xFF)) + if is_cpp: + f.write("\n") + if is_cpp: + f.write("};\n") + f.close() if len(sys.argv) <= 2: - print("Utility to export a image in Marlin TFT friendly format.") - print("It will dump a raw bin RGB565 image or create a CPP file with an array of 16 bit image pixels.") - print("Usage: gen-tft-image.py INPUT_IMAGE.(png|bmp|jpg) OUTPUT_FILE.(cpp|bin)") - print("Author: rhapsodyv") - exit(1) + print("Utility to export a image in Marlin TFT friendly format.") + print("It will dump a raw bin RGB565 image or create a CPP file with an array of 16 bit image pixels.") + print("Usage: gen-tft-image.py INPUT_IMAGE.(png|bmp|jpg) OUTPUT_FILE.(cpp|bin)") + print("Author: rhapsodyv") + exit(1) output_img = sys.argv[2] img = Image.open(sys.argv[1]) diff --git a/buildroot/share/scripts/upload.py b/buildroot/share/scripts/upload.py index ef042fcded..caa1fbae23 100644 --- a/buildroot/share/scripts/upload.py +++ b/buildroot/share/scripts/upload.py @@ -25,320 +25,320 @@ import MarlinBinaryProtocol #-----------------# def Upload(source, target, env): - #-------# - # Debug # - #-------# - Debug = False # Set to True to enable script debug - def debugPrint(data): - if Debug: print(f"[Debug]: {data}") + #-------# + # Debug # + #-------# + Debug = False # Set to True to enable script debug + def debugPrint(data): + if Debug: print(f"[Debug]: {data}") - #------------------# - # Marlin functions # - #------------------# - def _GetMarlinEnv(marlinEnv, feature): - if not marlinEnv: return None - return marlinEnv[feature] if feature in marlinEnv else None + #------------------# + # Marlin functions # + #------------------# + def _GetMarlinEnv(marlinEnv, feature): + if not marlinEnv: return None + return marlinEnv[feature] if feature in marlinEnv else None - #----------------# - # Port functions # - #----------------# - def _GetUploadPort(env): - debugPrint('Autodetecting upload port...') - env.AutodetectUploadPort(env) - portName = env.subst('$UPLOAD_PORT') - if not portName: - raise Exception('Error detecting the upload port.') - debugPrint('OK') - return portName + #----------------# + # Port functions # + #----------------# + def _GetUploadPort(env): + debugPrint('Autodetecting upload port...') + env.AutodetectUploadPort(env) + portName = env.subst('$UPLOAD_PORT') + if not portName: + raise Exception('Error detecting the upload port.') + debugPrint('OK') + return portName - #-------------------------# - # Simple serial functions # - #-------------------------# - def _OpenPort(): - # Open serial port - if port.is_open: return - debugPrint('Opening upload port...') - port.open() - port.reset_input_buffer() - debugPrint('OK') + #-------------------------# + # Simple serial functions # + #-------------------------# + def _OpenPort(): + # Open serial port + if port.is_open: return + debugPrint('Opening upload port...') + port.open() + port.reset_input_buffer() + debugPrint('OK') - def _ClosePort(): - # Open serial port - if port is None: return - if not port.is_open: return - debugPrint('Closing upload port...') - port.close() - debugPrint('OK') + def _ClosePort(): + # Open serial port + if port is None: return + if not port.is_open: return + debugPrint('Closing upload port...') + port.close() + debugPrint('OK') - def _Send(data): - debugPrint(f'>> {data}') - strdata = bytearray(data, 'utf8') + b'\n' - port.write(strdata) - time.sleep(0.010) + def _Send(data): + debugPrint(f'>> {data}') + strdata = bytearray(data, 'utf8') + b'\n' + port.write(strdata) + time.sleep(0.010) - def _Recv(): - clean_responses = [] - responses = port.readlines() - for Resp in responses: - # Suppress invalid chars (coming from debug info) - try: - clean_response = Resp.decode('utf8').rstrip().lstrip() - clean_responses.append(clean_response) - debugPrint(f'<< {clean_response}') - except: - pass - return clean_responses + def _Recv(): + clean_responses = [] + responses = port.readlines() + for Resp in responses: + # Suppress invalid chars (coming from debug info) + try: + clean_response = Resp.decode('utf8').rstrip().lstrip() + clean_responses.append(clean_response) + debugPrint(f'<< {clean_response}') + except: + pass + return clean_responses - #------------------# - # SDCard functions # - #------------------# - def _CheckSDCard(): - debugPrint('Checking SD card...') - _Send('M21') - Responses = _Recv() - if len(Responses) < 1 or not any('SD card ok' in r for r in Responses): - raise Exception('Error accessing SD card') - debugPrint('SD Card OK') - return True + #------------------# + # SDCard functions # + #------------------# + def _CheckSDCard(): + debugPrint('Checking SD card...') + _Send('M21') + Responses = _Recv() + if len(Responses) < 1 or not any('SD card ok' in r for r in Responses): + raise Exception('Error accessing SD card') + debugPrint('SD Card OK') + return True - #----------------# - # File functions # - #----------------# - def _GetFirmwareFiles(UseLongFilenames): - debugPrint('Get firmware files...') - _Send(f"M20 F{'L' if UseLongFilenames else ''}") - Responses = _Recv() - if len(Responses) < 3 or not any('file list' in r for r in Responses): - raise Exception('Error getting firmware files') - debugPrint('OK') - return Responses + #----------------# + # File functions # + #----------------# + def _GetFirmwareFiles(UseLongFilenames): + debugPrint('Get firmware files...') + _Send(f"M20 F{'L' if UseLongFilenames else ''}") + Responses = _Recv() + if len(Responses) < 3 or not any('file list' in r for r in Responses): + raise Exception('Error getting firmware files') + debugPrint('OK') + return Responses - def _FilterFirmwareFiles(FirmwareList, UseLongFilenames): - Firmwares = [] - for FWFile in FirmwareList: - # For long filenames take the 3rd column of the firmwares list - if UseLongFilenames: - Space = 0 - Space = FWFile.find(' ') - if Space >= 0: Space = FWFile.find(' ', Space + 1) - if Space >= 0: FWFile = FWFile[Space + 1:] - if not '/' in FWFile and '.BIN' in FWFile.upper(): - Firmwares.append(FWFile[:FWFile.upper().index('.BIN') + 4]) - return Firmwares + def _FilterFirmwareFiles(FirmwareList, UseLongFilenames): + Firmwares = [] + for FWFile in FirmwareList: + # For long filenames take the 3rd column of the firmwares list + if UseLongFilenames: + Space = 0 + Space = FWFile.find(' ') + if Space >= 0: Space = FWFile.find(' ', Space + 1) + if Space >= 0: FWFile = FWFile[Space + 1:] + if not '/' in FWFile and '.BIN' in FWFile.upper(): + Firmwares.append(FWFile[:FWFile.upper().index('.BIN') + 4]) + return Firmwares - def _RemoveFirmwareFile(FirmwareFile): - _Send(f'M30 /{FirmwareFile}') - Responses = _Recv() - Removed = len(Responses) >= 1 and any('File deleted' in r for r in Responses) - if not Removed: - raise Exception(f"Firmware file '{FirmwareFile}' not removed") - return Removed + def _RemoveFirmwareFile(FirmwareFile): + _Send(f'M30 /{FirmwareFile}') + Responses = _Recv() + Removed = len(Responses) >= 1 and any('File deleted' in r for r in Responses) + if not Removed: + raise Exception(f"Firmware file '{FirmwareFile}' not removed") + return Removed - def _RollbackUpload(FirmwareFile): - if not rollback: return - print(f"Rollback: trying to delete firmware '{FirmwareFile}'...") - _OpenPort() - # Wait for SD card release - time.sleep(1) - # Remount SD card - _CheckSDCard() - print(' OK' if _RemoveFirmwareFile(FirmwareFile) else ' Error!') - _ClosePort() + def _RollbackUpload(FirmwareFile): + if not rollback: return + print(f"Rollback: trying to delete firmware '{FirmwareFile}'...") + _OpenPort() + # Wait for SD card release + time.sleep(1) + # Remount SD card + _CheckSDCard() + print(' OK' if _RemoveFirmwareFile(FirmwareFile) else ' Error!') + _ClosePort() - #---------------------# - # Callback Entrypoint # - #---------------------# - port = None - protocol = None - filetransfer = None - rollback = False + #---------------------# + # Callback Entrypoint # + #---------------------# + port = None + protocol = None + filetransfer = None + rollback = False - # Get Marlin evironment vars - MarlinEnv = env['MARLIN_FEATURES'] - marlin_pioenv = _GetMarlinEnv(MarlinEnv, 'PIOENV') - marlin_motherboard = _GetMarlinEnv(MarlinEnv, 'MOTHERBOARD') - marlin_board_info_name = _GetMarlinEnv(MarlinEnv, 'BOARD_INFO_NAME') - marlin_board_custom_build_flags = _GetMarlinEnv(MarlinEnv, 'BOARD_CUSTOM_BUILD_FLAGS') - marlin_firmware_bin = _GetMarlinEnv(MarlinEnv, 'FIRMWARE_BIN') - marlin_long_filename_host_support = _GetMarlinEnv(MarlinEnv, 'LONG_FILENAME_HOST_SUPPORT') is not None - marlin_longname_write = _GetMarlinEnv(MarlinEnv, 'LONG_FILENAME_WRITE_SUPPORT') is not None - marlin_custom_firmware_upload = _GetMarlinEnv(MarlinEnv, 'CUSTOM_FIRMWARE_UPLOAD') is not None - marlin_short_build_version = _GetMarlinEnv(MarlinEnv, 'SHORT_BUILD_VERSION') - marlin_string_config_h_author = _GetMarlinEnv(MarlinEnv, 'STRING_CONFIG_H_AUTHOR') + # Get Marlin evironment vars + MarlinEnv = env['MARLIN_FEATURES'] + marlin_pioenv = _GetMarlinEnv(MarlinEnv, 'PIOENV') + marlin_motherboard = _GetMarlinEnv(MarlinEnv, 'MOTHERBOARD') + marlin_board_info_name = _GetMarlinEnv(MarlinEnv, 'BOARD_INFO_NAME') + marlin_board_custom_build_flags = _GetMarlinEnv(MarlinEnv, 'BOARD_CUSTOM_BUILD_FLAGS') + marlin_firmware_bin = _GetMarlinEnv(MarlinEnv, 'FIRMWARE_BIN') + marlin_long_filename_host_support = _GetMarlinEnv(MarlinEnv, 'LONG_FILENAME_HOST_SUPPORT') is not None + marlin_longname_write = _GetMarlinEnv(MarlinEnv, 'LONG_FILENAME_WRITE_SUPPORT') is not None + marlin_custom_firmware_upload = _GetMarlinEnv(MarlinEnv, 'CUSTOM_FIRMWARE_UPLOAD') is not None + marlin_short_build_version = _GetMarlinEnv(MarlinEnv, 'SHORT_BUILD_VERSION') + marlin_string_config_h_author = _GetMarlinEnv(MarlinEnv, 'STRING_CONFIG_H_AUTHOR') - # Get firmware upload params - upload_firmware_source_name = str(source[0]) # Source firmware filename - upload_speed = env['UPLOAD_SPEED'] if 'UPLOAD_SPEED' in env else 115200 - # baud rate of serial connection - upload_port = _GetUploadPort(env) # Serial port to use + # Get firmware upload params + upload_firmware_source_name = str(source[0]) # Source firmware filename + upload_speed = env['UPLOAD_SPEED'] if 'UPLOAD_SPEED' in env else 115200 + # baud rate of serial connection + upload_port = _GetUploadPort(env) # Serial port to use - # Set local upload params - upload_firmware_target_name = os.path.basename(upload_firmware_source_name) - # Target firmware filename - upload_timeout = 1000 # Communication timout, lossy/slow connections need higher values - upload_blocksize = 512 # Transfer block size. 512 = Autodetect - upload_compression = True # Enable compression - upload_error_ratio = 0 # Simulated corruption ratio - upload_test = False # Benchmark the serial link without storing the file - upload_reset = True # Trigger a soft reset for firmware update after the upload + # Set local upload params + upload_firmware_target_name = os.path.basename(upload_firmware_source_name) + # Target firmware filename + upload_timeout = 1000 # Communication timout, lossy/slow connections need higher values + upload_blocksize = 512 # Transfer block size. 512 = Autodetect + upload_compression = True # Enable compression + upload_error_ratio = 0 # Simulated corruption ratio + upload_test = False # Benchmark the serial link without storing the file + upload_reset = True # Trigger a soft reset for firmware update after the upload - # Set local upload params based on board type to change script behavior - # "upload_delete_old_bins": delete all *.bin files in the root of SD Card - upload_delete_old_bins = marlin_motherboard in ['BOARD_CREALITY_V4', 'BOARD_CREALITY_V4210', 'BOARD_CREALITY_V422', 'BOARD_CREALITY_V423', - 'BOARD_CREALITY_V427', 'BOARD_CREALITY_V431', 'BOARD_CREALITY_V452', 'BOARD_CREALITY_V453', - 'BOARD_CREALITY_V24S1'] - # "upload_random_name": generate a random 8.3 firmware filename to upload - upload_random_filename = marlin_motherboard in ['BOARD_CREALITY_V4', 'BOARD_CREALITY_V4210', 'BOARD_CREALITY_V422', 'BOARD_CREALITY_V423', - 'BOARD_CREALITY_V427', 'BOARD_CREALITY_V431', 'BOARD_CREALITY_V452', 'BOARD_CREALITY_V453', - 'BOARD_CREALITY_V24S1'] and not marlin_long_filename_host_support + # Set local upload params based on board type to change script behavior + # "upload_delete_old_bins": delete all *.bin files in the root of SD Card + upload_delete_old_bins = marlin_motherboard in ['BOARD_CREALITY_V4', 'BOARD_CREALITY_V4210', 'BOARD_CREALITY_V422', 'BOARD_CREALITY_V423', + 'BOARD_CREALITY_V427', 'BOARD_CREALITY_V431', 'BOARD_CREALITY_V452', 'BOARD_CREALITY_V453', + 'BOARD_CREALITY_V24S1'] + # "upload_random_name": generate a random 8.3 firmware filename to upload + upload_random_filename = marlin_motherboard in ['BOARD_CREALITY_V4', 'BOARD_CREALITY_V4210', 'BOARD_CREALITY_V422', 'BOARD_CREALITY_V423', + 'BOARD_CREALITY_V427', 'BOARD_CREALITY_V431', 'BOARD_CREALITY_V452', 'BOARD_CREALITY_V453', + 'BOARD_CREALITY_V24S1'] and not marlin_long_filename_host_support - try: + try: - # Start upload job - print(f"Uploading firmware '{os.path.basename(upload_firmware_target_name)}' to '{marlin_motherboard}' via '{upload_port}'") + # Start upload job + print(f"Uploading firmware '{os.path.basename(upload_firmware_target_name)}' to '{marlin_motherboard}' via '{upload_port}'") - # Dump some debug info - if Debug: - print('Upload using:') - print('---- Marlin -----------------------------------') - print(f' PIOENV : {marlin_pioenv}') - print(f' SHORT_BUILD_VERSION : {marlin_short_build_version}') - print(f' STRING_CONFIG_H_AUTHOR : {marlin_string_config_h_author}') - print(f' MOTHERBOARD : {marlin_motherboard}') - print(f' BOARD_INFO_NAME : {marlin_board_info_name}') - print(f' CUSTOM_BUILD_FLAGS : {marlin_board_custom_build_flags}') - print(f' FIRMWARE_BIN : {marlin_firmware_bin}') - print(f' LONG_FILENAME_HOST_SUPPORT : {marlin_long_filename_host_support}') - print(f' LONG_FILENAME_WRITE_SUPPORT : {marlin_longname_write}') - print(f' CUSTOM_FIRMWARE_UPLOAD : {marlin_custom_firmware_upload}') - print('---- Upload parameters ------------------------') - print(f' Source : {upload_firmware_source_name}') - print(f' Target : {upload_firmware_target_name}') - print(f' Port : {upload_port} @ {upload_speed} baudrate') - print(f' Timeout : {upload_timeout}') - print(f' Block size : {upload_blocksize}') - print(f' Compression : {upload_compression}') - print(f' Error ratio : {upload_error_ratio}') - print(f' Test : {upload_test}') - print(f' Reset : {upload_reset}') - print('-----------------------------------------------') + # Dump some debug info + if Debug: + print('Upload using:') + print('---- Marlin -----------------------------------') + print(f' PIOENV : {marlin_pioenv}') + print(f' SHORT_BUILD_VERSION : {marlin_short_build_version}') + print(f' STRING_CONFIG_H_AUTHOR : {marlin_string_config_h_author}') + print(f' MOTHERBOARD : {marlin_motherboard}') + print(f' BOARD_INFO_NAME : {marlin_board_info_name}') + print(f' CUSTOM_BUILD_FLAGS : {marlin_board_custom_build_flags}') + print(f' FIRMWARE_BIN : {marlin_firmware_bin}') + print(f' LONG_FILENAME_HOST_SUPPORT : {marlin_long_filename_host_support}') + print(f' LONG_FILENAME_WRITE_SUPPORT : {marlin_longname_write}') + print(f' CUSTOM_FIRMWARE_UPLOAD : {marlin_custom_firmware_upload}') + print('---- Upload parameters ------------------------') + print(f' Source : {upload_firmware_source_name}') + print(f' Target : {upload_firmware_target_name}') + print(f' Port : {upload_port} @ {upload_speed} baudrate') + print(f' Timeout : {upload_timeout}') + print(f' Block size : {upload_blocksize}') + print(f' Compression : {upload_compression}') + print(f' Error ratio : {upload_error_ratio}') + print(f' Test : {upload_test}') + print(f' Reset : {upload_reset}') + print('-----------------------------------------------') - # Custom implementations based on board parameters - # Generate a new 8.3 random filename - if upload_random_filename: - upload_firmware_target_name = f"fw-{''.join(random.choices('ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456789', k=5))}.BIN" - print(f"Board {marlin_motherboard}: Overriding firmware filename to '{upload_firmware_target_name}'") + # Custom implementations based on board parameters + # Generate a new 8.3 random filename + if upload_random_filename: + upload_firmware_target_name = f"fw-{''.join(random.choices('ABCDEFGHIJKLMNOPQRSTUVWXYZ0123456789', k=5))}.BIN" + print(f"Board {marlin_motherboard}: Overriding firmware filename to '{upload_firmware_target_name}'") - # Delete all *.bin files on the root of SD Card (if flagged) - if upload_delete_old_bins: - # CUSTOM_FIRMWARE_UPLOAD is needed for this feature - if not marlin_custom_firmware_upload: - raise Exception(f"CUSTOM_FIRMWARE_UPLOAD must be enabled in 'Configuration_adv.h' for '{marlin_motherboard}'") + # Delete all *.bin files on the root of SD Card (if flagged) + if upload_delete_old_bins: + # CUSTOM_FIRMWARE_UPLOAD is needed for this feature + if not marlin_custom_firmware_upload: + raise Exception(f"CUSTOM_FIRMWARE_UPLOAD must be enabled in 'Configuration_adv.h' for '{marlin_motherboard}'") - # Init & Open serial port - port = serial.Serial(upload_port, baudrate = upload_speed, write_timeout = 0, timeout = 0.1) - _OpenPort() + # Init & Open serial port + port = serial.Serial(upload_port, baudrate = upload_speed, write_timeout = 0, timeout = 0.1) + _OpenPort() - # Check SD card status - _CheckSDCard() + # Check SD card status + _CheckSDCard() - # Get firmware files - FirmwareFiles = _GetFirmwareFiles(marlin_long_filename_host_support) - if Debug: - for FirmwareFile in FirmwareFiles: - print(f'Found: {FirmwareFile}') + # Get firmware files + FirmwareFiles = _GetFirmwareFiles(marlin_long_filename_host_support) + if Debug: + for FirmwareFile in FirmwareFiles: + print(f'Found: {FirmwareFile}') - # Get all 1st level firmware files (to remove) - OldFirmwareFiles = _FilterFirmwareFiles(FirmwareFiles[1:len(FirmwareFiles)-2], marlin_long_filename_host_support) # Skip header and footers of list - if len(OldFirmwareFiles) == 0: - print('No old firmware files to delete') - else: - print(f"Remove {len(OldFirmwareFiles)} old firmware file{'s' if len(OldFirmwareFiles) != 1 else ''}:") - for OldFirmwareFile in OldFirmwareFiles: - print(f" -Removing- '{OldFirmwareFile}'...") - print(' OK' if _RemoveFirmwareFile(OldFirmwareFile) else ' Error!') + # Get all 1st level firmware files (to remove) + OldFirmwareFiles = _FilterFirmwareFiles(FirmwareFiles[1:len(FirmwareFiles)-2], marlin_long_filename_host_support) # Skip header and footers of list + if len(OldFirmwareFiles) == 0: + print('No old firmware files to delete') + else: + print(f"Remove {len(OldFirmwareFiles)} old firmware file{'s' if len(OldFirmwareFiles) != 1 else ''}:") + for OldFirmwareFile in OldFirmwareFiles: + print(f" -Removing- '{OldFirmwareFile}'...") + print(' OK' if _RemoveFirmwareFile(OldFirmwareFile) else ' Error!') - # Close serial - _ClosePort() + # Close serial + _ClosePort() - # Cleanup completed - debugPrint('Cleanup completed') + # Cleanup completed + debugPrint('Cleanup completed') - # WARNING! The serial port must be closed here because the serial transfer that follow needs it! + # WARNING! The serial port must be closed here because the serial transfer that follow needs it! - # Upload firmware file - debugPrint(f"Copy '{upload_firmware_source_name}' --> '{upload_firmware_target_name}'") - protocol = MarlinBinaryProtocol.Protocol(upload_port, upload_speed, upload_blocksize, float(upload_error_ratio), int(upload_timeout)) - #echologger = MarlinBinaryProtocol.EchoProtocol(protocol) - protocol.connect() - # Mark the rollback (delete broken transfer) from this point on - rollback = True - filetransfer = MarlinBinaryProtocol.FileTransferProtocol(protocol) - transferOK = filetransfer.copy(upload_firmware_source_name, upload_firmware_target_name, upload_compression, upload_test) - protocol.disconnect() + # Upload firmware file + debugPrint(f"Copy '{upload_firmware_source_name}' --> '{upload_firmware_target_name}'") + protocol = MarlinBinaryProtocol.Protocol(upload_port, upload_speed, upload_blocksize, float(upload_error_ratio), int(upload_timeout)) + #echologger = MarlinBinaryProtocol.EchoProtocol(protocol) + protocol.connect() + # Mark the rollback (delete broken transfer) from this point on + rollback = True + filetransfer = MarlinBinaryProtocol.FileTransferProtocol(protocol) + transferOK = filetransfer.copy(upload_firmware_source_name, upload_firmware_target_name, upload_compression, upload_test) + protocol.disconnect() - # Notify upload completed - protocol.send_ascii('M117 Firmware uploaded' if transferOK else 'M117 Firmware upload failed') + # Notify upload completed + protocol.send_ascii('M117 Firmware uploaded' if transferOK else 'M117 Firmware upload failed') - # Remount SD card - print('Wait for SD card release...') - time.sleep(1) - print('Remount SD card') - protocol.send_ascii('M21') + # Remount SD card + print('Wait for SD card release...') + time.sleep(1) + print('Remount SD card') + protocol.send_ascii('M21') - # Transfer failed? - if not transferOK: - protocol.shutdown() - _RollbackUpload(upload_firmware_target_name) - else: - # Trigger firmware update - if upload_reset: - print('Trigger firmware update...') - protocol.send_ascii('M997', True) - protocol.shutdown() + # Transfer failed? + if not transferOK: + protocol.shutdown() + _RollbackUpload(upload_firmware_target_name) + else: + # Trigger firmware update + if upload_reset: + print('Trigger firmware update...') + protocol.send_ascii('M997', True) + protocol.shutdown() - print('Firmware update completed' if transferOK else 'Firmware update failed') - return 0 if transferOK else -1 + print('Firmware update completed' if transferOK else 'Firmware update failed') + return 0 if transferOK else -1 - except KeyboardInterrupt: - print('Aborted by user') - if filetransfer: filetransfer.abort() - if protocol: - protocol.disconnect() - protocol.shutdown() - _RollbackUpload(upload_firmware_target_name) - _ClosePort() - raise + except KeyboardInterrupt: + print('Aborted by user') + if filetransfer: filetransfer.abort() + if protocol: + protocol.disconnect() + protocol.shutdown() + _RollbackUpload(upload_firmware_target_name) + _ClosePort() + raise - except serial.SerialException as se: - # This exception is raised only for send_ascii data (not for binary transfer) - print(f'Serial excepion: {se}, transfer aborted') - if protocol: - protocol.disconnect() - protocol.shutdown() - _RollbackUpload(upload_firmware_target_name) - _ClosePort() - raise Exception(se) + except serial.SerialException as se: + # This exception is raised only for send_ascii data (not for binary transfer) + print(f'Serial excepion: {se}, transfer aborted') + if protocol: + protocol.disconnect() + protocol.shutdown() + _RollbackUpload(upload_firmware_target_name) + _ClosePort() + raise Exception(se) - except MarlinBinaryProtocol.FatalError: - print('Too many retries, transfer aborted') - if protocol: - protocol.disconnect() - protocol.shutdown() - _RollbackUpload(upload_firmware_target_name) - _ClosePort() - raise + except MarlinBinaryProtocol.FatalError: + print('Too many retries, transfer aborted') + if protocol: + protocol.disconnect() + protocol.shutdown() + _RollbackUpload(upload_firmware_target_name) + _ClosePort() + raise - except Exception as ex: - print(f"\nException: {ex}, transfer aborted") - if protocol: - protocol.disconnect() - protocol.shutdown() - _RollbackUpload(upload_firmware_target_name) - _ClosePort() - print('Firmware not updated') - raise + except Exception as ex: + print(f"\nException: {ex}, transfer aborted") + if protocol: + protocol.disconnect() + protocol.shutdown() + _RollbackUpload(upload_firmware_target_name) + _ClosePort() + print('Firmware not updated') + raise # Attach custom upload callback env.Replace(UPLOADCMD=Upload) diff --git a/buildroot/tests/SAMD51_grandcentral_m4 b/buildroot/tests/SAMD51_grandcentral_m4 index c8e08c19e6..f96e0b18cd 100755 --- a/buildroot/tests/SAMD51_grandcentral_m4 +++ b/buildroot/tests/SAMD51_grandcentral_m4 @@ -21,7 +21,7 @@ opt_enable ENDSTOP_INTERRUPTS_FEATURE S_CURVE_ACCELERATION BLTOUCH Z_MIN_PROBE_R FILAMENT_RUNOUT_SENSOR G26_MESH_VALIDATION MESH_EDIT_GFX_OVERLAY Z_SAFE_HOMING \ EEPROM_SETTINGS NOZZLE_PARK_FEATURE SDSUPPORT SD_CHECK_AND_RETRY \ REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER Z_STEPPER_AUTO_ALIGN ADAPTIVE_STEP_SMOOTHING \ - STATUS_MESSAGE_SCROLLING LCD_SET_PROGRESS_MANUALLY SHOW_REMAINING_TIME USE_M73_REMAINING_TIME \ + STATUS_MESSAGE_SCROLLING SET_PROGRESS_MANUALLY SHOW_REMAINING_TIME SET_REMAINING_TIME \ LONG_FILENAME_HOST_SUPPORT CUSTOM_FIRMWARE_UPLOAD M20_TIMESTAMP_SUPPORT \ SCROLL_LONG_FILENAMES BABYSTEPPING DOUBLECLICK_FOR_Z_BABYSTEPPING \ MOVE_Z_WHEN_IDLE BABYSTEP_ZPROBE_OFFSET BABYSTEP_ZPROBE_GFX_OVERLAY \ diff --git a/buildroot/tests/STM32F103RE_creality b/buildroot/tests/STM32F103RE_creality index f1478bc2c4..a3c52372ef 100644 --- a/buildroot/tests/STM32F103RE_creality +++ b/buildroot/tests/STM32F103RE_creality @@ -20,7 +20,7 @@ exec_test $1 $2 "Ender 3 v2 with JyersUI" "$3" use_example_configs "Creality/Ender-3 S1/STM32F1" opt_disable DWIN_CREALITY_LCD Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN AUTO_BED_LEVELING_BILINEAR CONFIGURATION_EMBEDDING CANCEL_OBJECTS FWRETRACT -opt_enable DWIN_LCD_PROUI INDIVIDUAL_AXIS_HOMING_SUBMENU LCD_SET_PROGRESS_MANUALLY STATUS_MESSAGE_SCROLLING \ +opt_enable DWIN_LCD_PROUI INDIVIDUAL_AXIS_HOMING_SUBMENU SET_PROGRESS_MANUALLY SET_PROGRESS_PERCENT STATUS_MESSAGE_SCROLLING \ SOUND_MENU_ITEM PRINTCOUNTER NOZZLE_PARK_FEATURE ADVANCED_PAUSE_FEATURE FILAMENT_RUNOUT_SENSOR \ BLTOUCH Z_SAFE_HOMING AUTO_BED_LEVELING_UBL MESH_EDIT_MENU \ LIMITED_MAX_FR_EDITING LIMITED_MAX_ACCEL_EDITING LIMITED_JERK_EDITING BAUD_RATE_GCODE diff --git a/buildroot/tests/mega2560 b/buildroot/tests/mega2560 index 64f1bb07d2..0f636621e9 100755 --- a/buildroot/tests/mega2560 +++ b/buildroot/tests/mega2560 @@ -30,8 +30,8 @@ opt_enable AUTO_BED_LEVELING_UBL RESTORE_LEVELING_AFTER_G28 DEBUG_LEVELING_FEATU REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER LIGHTWEIGHT_UI STATUS_MESSAGE_SCROLLING SHOW_CUSTOM_BOOTSCREEN BOOT_MARLIN_LOGO_SMALL \ SDSUPPORT SDCARD_SORT_ALPHA USB_FLASH_DRIVE_SUPPORT AUTO_REPORT_SD_STATUS SCROLL_LONG_FILENAMES MEDIA_MENU_AT_TOP \ EEPROM_SETTINGS EEPROM_CHITCHAT GCODE_MACROS CUSTOM_MENU_MAIN FREEZE_FEATURE CANCEL_OBJECTS SOUND_MENU_ITEM \ - MULTI_NOZZLE_DUPLICATION CLASSIC_JERK LIN_ADVANCE EXTRA_LIN_ADVANCE_K QUICK_HOME \ - LCD_SET_PROGRESS_MANUALLY PRINT_PROGRESS_SHOW_DECIMALS SHOW_REMAINING_TIME \ + MULTI_NOZZLE_DUPLICATION CLASSIC_JERK LIN_ADVANCE ADVANCE_K_EXTRA QUICK_HOME \ + SET_PROGRESS_MANUALLY SET_PROGRESS_PERCENT PRINT_PROGRESS_SHOW_DECIMALS SHOW_REMAINING_TIME \ ENCODER_NOISE_FILTER BABYSTEPPING BABYSTEP_XY NANODLP_Z_SYNC I2C_POSITION_ENCODERS M114_DETAIL exec_test $1 $2 "Azteeg X3 Pro | EXTRUDERS 5 | RRDFGSC | UBL | LIN_ADVANCE ..." "$3" @@ -42,7 +42,7 @@ use_example_configs AnimationExample opt_set MOTHERBOARD BOARD_AZTEEG_X3_PRO LCD_LANGUAGE jp_kana DEFAULT_EJERK 10 \ EXTRUDERS 5 TEMP_SENSOR_1 1 TEMP_SENSOR_2 5 TEMP_SENSOR_3 20 TEMP_SENSOR_4 1000 TEMP_SENSOR_BED 1 opt_enable REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER LIGHTWEIGHT_UI SHOW_CUSTOM_BOOTSCREEN BOOT_MARLIN_LOGO_SMALL \ - LCD_SET_PROGRESS_MANUALLY PRINT_PROGRESS_SHOW_DECIMALS SHOW_REMAINING_TIME STATUS_MESSAGE_SCROLLING SCROLL_LONG_FILENAMES \ + SET_PROGRESS_MANUALLY SET_PROGRESS_PERCENT PRINT_PROGRESS_SHOW_DECIMALS SHOW_REMAINING_TIME STATUS_MESSAGE_SCROLLING SCROLL_LONG_FILENAMES \ SDSUPPORT LONG_FILENAME_WRITE_SUPPORT SDCARD_SORT_ALPHA NO_SD_AUTOSTART USB_FLASH_DRIVE_SUPPORT CANCEL_OBJECTS \ Z_PROBE_SLED AUTO_BED_LEVELING_UBL UBL_HILBERT_CURVE RESTORE_LEVELING_AFTER_G28 DEBUG_LEVELING_FEATURE G26_MESH_VALIDATION ENABLE_LEVELING_FADE_HEIGHT \ EEPROM_SETTINGS EEPROM_CHITCHAT GCODE_MACROS CUSTOM_MENU_MAIN \ @@ -177,52 +177,52 @@ exec_test $1 $2 "Azteeg X3 | Mixing Extruder (x5) | Gradient Mix | Greek" "$3" #opt_enable LCM1602 #exec_test $1 $2 "Stuff" "$3" -# -# Test Laser features with 12864 LCD -# -restore_configs -opt_set MOTHERBOARD BOARD_RAMPS_14_EFB EXTRUDERS 0 LCD_LANGUAGE en TEMP_SENSOR_COOLER 1 TEMP_SENSOR_1 0 SERIAL_PORT_2 2 \ - DEFAULT_AXIS_STEPS_PER_UNIT '{ 80, 80, 400 }' \ - DEFAULT_MAX_FEEDRATE '{ 300, 300, 5 }' \ - DEFAULT_MAX_ACCELERATION '{ 3000, 3000, 100 }' \ - MANUAL_FEEDRATE '{ 50*60, 50*60, 4*60 }' \ - AXIS_RELATIVE_MODES '{ false, false, false }' -opt_enable REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER SDSUPPORT EEPROM_SETTINGS EEPROM_BOOT_SILENT EEPROM_AUTO_INIT MEATPACK_ON_SERIAL_PORT_1 \ - LASER_FEATURE LASER_SAFETY_TIMEOUT_MS LASER_COOLANT_FLOW_METER AIR_EVACUATION AIR_EVACUATION_PIN AIR_ASSIST AIR_ASSIST_PIN LASER_SYNCHRONOUS_M106_M107 -exec_test $1 $2 "MEGA2560 RAMPS | Laser Options | 12864 | Meatpack | Fan Sync | SERIAL_PORT_2 " "$3" +# # +# # Test Laser features with 12864 LCD +# # +# restore_configs +# opt_set MOTHERBOARD BOARD_RAMPS_14_EFB EXTRUDERS 0 LCD_LANGUAGE en TEMP_SENSOR_COOLER 1 TEMP_SENSOR_1 0 SERIAL_PORT_2 2 \ +# DEFAULT_AXIS_STEPS_PER_UNIT '{ 80, 80, 400 }' \ +# DEFAULT_MAX_FEEDRATE '{ 300, 300, 5 }' \ +# DEFAULT_MAX_ACCELERATION '{ 3000, 3000, 100 }' \ +# MANUAL_FEEDRATE '{ 50*60, 50*60, 4*60 }' \ +# AXIS_RELATIVE_MODES '{ false, false, false }' +# opt_enable REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER SDSUPPORT EEPROM_SETTINGS EEPROM_BOOT_SILENT EEPROM_AUTO_INIT MEATPACK_ON_SERIAL_PORT_1 \ +# LASER_FEATURE LASER_SAFETY_TIMEOUT_MS LASER_COOLANT_FLOW_METER AIR_EVACUATION AIR_EVACUATION_PIN AIR_ASSIST AIR_ASSIST_PIN LASER_SYNCHRONOUS_M106_M107 +# exec_test $1 $2 "MEGA2560 RAMPS | Laser Options | 12864 | Meatpack | Fan Sync | SERIAL_PORT_2 " "$3" -# -# Test Laser features with 44780 LCD -# -restore_configs -opt_set MOTHERBOARD BOARD_RAMPS_14_EFB EXTRUDERS 0 LCD_LANGUAGE en TEMP_SENSOR_COOLER 1 TEMP_SENSOR_1 0 \ - DEFAULT_AXIS_STEPS_PER_UNIT '{ 80, 80, 400 }' \ - DEFAULT_MAX_FEEDRATE '{ 300, 300, 5 }' \ - DEFAULT_MAX_ACCELERATION '{ 3000, 3000, 100 }' \ - MANUAL_FEEDRATE '{ 50*60, 50*60, 4*60 }' \ - AXIS_RELATIVE_MODES '{ false, false, false }' -opt_enable REPRAP_DISCOUNT_SMART_CONTROLLER SDSUPPORT EEPROM_SETTINGS EEPROM_BOOT_SILENT EEPROM_AUTO_INIT PRINTCOUNTER I2C_AMMETER \ - LASER_FEATURE LASER_SAFETY_TIMEOUT_MS LASER_COOLANT_FLOW_METER AIR_EVACUATION AIR_EVACUATION_PIN AIR_ASSIST AIR_ASSIST_PIN -exec_test $1 $2 "MEGA2560 RAMPS | Laser Feature | Air Evacuation | Air Assist | Cooler | Laser Safety Timeout | Flowmeter | 44780 LCD " "$3" +# # +# # Test Laser features with 44780 LCD +# # +# restore_configs +# opt_set MOTHERBOARD BOARD_RAMPS_14_EFB EXTRUDERS 0 LCD_LANGUAGE en TEMP_SENSOR_COOLER 1 TEMP_SENSOR_1 0 \ +# DEFAULT_AXIS_STEPS_PER_UNIT '{ 80, 80, 400 }' \ +# DEFAULT_MAX_FEEDRATE '{ 300, 300, 5 }' \ +# DEFAULT_MAX_ACCELERATION '{ 3000, 3000, 100 }' \ +# MANUAL_FEEDRATE '{ 50*60, 50*60, 4*60 }' \ +# AXIS_RELATIVE_MODES '{ false, false, false }' +# opt_enable REPRAP_DISCOUNT_SMART_CONTROLLER SDSUPPORT EEPROM_SETTINGS EEPROM_BOOT_SILENT EEPROM_AUTO_INIT PRINTCOUNTER I2C_AMMETER \ +# LASER_FEATURE LASER_SAFETY_TIMEOUT_MS LASER_COOLANT_FLOW_METER AIR_EVACUATION AIR_EVACUATION_PIN AIR_ASSIST AIR_ASSIST_PIN +# exec_test $1 $2 "MEGA2560 RAMPS | Laser Feature | Air Evacuation | Air Assist | Cooler | Laser Safety Timeout | Flowmeter | 44780 LCD " "$3" -# -# Test redundant temperature sensors + MAX TC + Backlight Timeout -# -restore_configs -opt_set MOTHERBOARD BOARD_RAMPS_14_EFB EXTRUDERS 1 \ - TEMP_SENSOR_0 -2 TEMP_SENSOR_REDUNDANT -2 \ - TEMP_SENSOR_REDUNDANT_SOURCE E1 TEMP_SENSOR_REDUNDANT_TARGET E0 \ - TEMP_0_CS_PIN 11 TEMP_1_CS_PIN 12 \ - LCD_BACKLIGHT_TIMEOUT_MINS 2 -opt_enable MPCTEMP MINIPANEL -opt_disable PIDTEMP -exec_test $1 $2 "MEGA2560 RAMPS | Redundant temperature sensor | 2x MAX6675 | BL Timeout" "$3" +# # +# # Test redundant temperature sensors + MAX TC + Backlight Timeout +# # +# restore_configs +# opt_set MOTHERBOARD BOARD_RAMPS_14_EFB EXTRUDERS 1 \ +# TEMP_SENSOR_0 -2 TEMP_SENSOR_REDUNDANT -2 \ +# TEMP_SENSOR_REDUNDANT_SOURCE E1 TEMP_SENSOR_REDUNDANT_TARGET E0 \ +# TEMP_0_CS_PIN 11 TEMP_1_CS_PIN 12 \ +# LCD_BACKLIGHT_TIMEOUT_MINS 2 +# opt_enable MPCTEMP MINIPANEL +# opt_disable PIDTEMP +# exec_test $1 $2 "MEGA2560 RAMPS | Redundant temperature sensor | 2x MAX6675 | BL Timeout" "$3" -# -# Polargraph Config -# -use_example_configs Polargraph -exec_test $1 $2 "RUMBA | POLARGRAPH | RRD LCD" "$3" +# # +# # Polargraph Config +# # +# use_example_configs Polargraph +# exec_test $1 $2 "RUMBA | POLARGRAPH | RRD LCD" "$3" # # Language files test with REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER @@ -239,8 +239,8 @@ exec_test $1 $2 "RUMBA | POLARGRAPH | RRD LCD" "$3" # # Test a basic DUAL_X_CARRIAGE configuration # -use_example_configs Formbot/T_Rex_3 -exec_test $1 $2 "Formbot/T_Rex_3 example configuration." "$3" +# use_example_configs Formbot/T_Rex_3 +# exec_test $1 $2 "Formbot/T_Rex_3 example configuration." "$3" # # BQ Hephestos 2 @@ -260,5 +260,20 @@ exec_test $1 $2 "Formbot/T_Rex_3 example configuration." "$3" #use_example_configs tvrrug/Round2 #exec_test $1 $2 "Stuff" "$3" +# +# Test progress display rotation +# +restore_configs +opt_set MOTHERBOARD BOARD_RAMPS_14_EFB +opt_enable REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER \ + SET_PROGRESS_MANUALLY SET_PROGRESS_PERCENT SET_REMAINING_TIME SET_INTERACTION_TIME M73_REPORT \ + SHOW_PROGRESS_PERCENT SHOW_ELAPSED_TIME SHOW_REMAINING_TIME SHOW_INTERACTION_TIME PRINT_PROGRESS_SHOW_DECIMALS +exec_test $1 $2 "MEGA2560 RAMPS | 12864 | progress rotation" "$3" +opt_enable LIGHTWEIGHT_UI +exec_test $1 $2 "MEGA2560 RAMPS | 12864 LIGHTWEIGHT_UI | progress rotation" "$3" +opt_disable REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER +opt_enable REPRAP_DISCOUNT_SMART_CONTROLLER +exec_test $1 $2 "MEGA2560 RAMPS | 44780 | progress rotation" "$3" + # clean up restore_configs diff --git a/buildroot/tests/rambo b/buildroot/tests/rambo index a980d2fe4e..a2c99efec0 100644 --- a/buildroot/tests/rambo +++ b/buildroot/tests/rambo @@ -34,7 +34,7 @@ opt_enable USE_ZMAX_PLUG REPRAP_DISCOUNT_SMART_CONTROLLER LCD_PROGRESS_BAR LCD_P FWRETRACT ARC_P_CIRCLES CNC_WORKSPACE_PLANES CNC_COORDINATE_SYSTEMS \ PSU_CONTROL PS_OFF_CONFIRM PS_OFF_SOUND POWER_OFF_WAIT_FOR_COOLDOWN \ POWER_LOSS_RECOVERY POWER_LOSS_PIN POWER_LOSS_STATE POWER_LOSS_RECOVER_ZHOME POWER_LOSS_ZHOME_POS \ - SLOW_PWM_HEATERS THERMAL_PROTECTION_CHAMBER LIN_ADVANCE EXTRA_LIN_ADVANCE_K \ + SLOW_PWM_HEATERS THERMAL_PROTECTION_CHAMBER LIN_ADVANCE ADVANCE_K_EXTRA \ HOST_ACTION_COMMANDS HOST_PROMPT_SUPPORT PINS_DEBUGGING MAX7219_DEBUG M114_DETAIL opt_add DEBUG_POWER_LOSS_RECOVERY exec_test $1 $2 "RAMBO | EXTRUDERS 2 | CHAR LCD + SD | FIX Probe | ABL-Linear | Advanced Pause | PLR | LEDs ..." "$3" @@ -93,7 +93,7 @@ opt_set MOTHERBOARD BOARD_MINIRAMBO \ opt_enable EEPROM_SETTINGS EEPROM_CHITCHAT REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER \ SDSUPPORT PCA9632 SOUND_MENU_ITEM GCODE_REPEAT_MARKERS \ AUTO_BED_LEVELING_LINEAR PROBE_MANUALLY LCD_BED_LEVELING \ - LIN_ADVANCE EXTRA_LIN_ADVANCE_K \ + LIN_ADVANCE ADVANCE_K_EXTRA \ INCH_MODE_SUPPORT TEMPERATURE_UNITS_SUPPORT EXPERIMENTAL_I2CBUS M100_FREE_MEMORY_WATCHER \ NOZZLE_PARK_FEATURE NOZZLE_CLEAN_FEATURE \ ADVANCED_PAUSE_FEATURE PARK_HEAD_ON_PAUSE ADVANCED_PAUSE_CONTINUOUS_PURGE FILAMENT_LOAD_UNLOAD_GCODES \ diff --git a/ini/features.ini b/ini/features.ini index 26185f332d..3aecd7474c 100644 --- a/ini/features.ini +++ b/ini/features.ini @@ -37,7 +37,7 @@ USES_LIQUIDCRYSTAL_I2C = marcoschwartz/LiquidCrystal_I2C@1.1.4 USES_LIQUIDTWI2 = LiquidTWI2@1.2.7 HAS_LCDPRINT = src_filter=+ HAS_MARLINUI_HD44780 = src_filter=+ -HAS_MARLINUI_U8GLIB = U8glib-HAL@~0.5.2 +HAS_MARLINUI_U8GLIB = marlinfirmware/U8glib-HAL@~0.5.2 src_filter=+ HAS_(FSMC|SPI|LTDC)_TFT = src_filter=+ + + HAS_FSMC_TFT = src_filter=+ + @@ -203,7 +203,7 @@ AUTO_REPORT_POSITION = src_filter=+ REPETIER_GCODE_M360 = src_filter=+ HAS_GCODE_M876 = src_filter=+ HAS_RESUME_CONTINUE = src_filter=+ -LCD_SET_PROGRESS_MANUALLY = src_filter=+ +SET_PROGRESS_MANUALLY = src_filter=+ HAS_STATUS_MESSAGE = src_filter=+ HAS_LCD_CONTRAST = src_filter=+ HAS_GCODE_M255 = src_filter=+ @@ -240,7 +240,7 @@ HAS_SERVOS = src_filter=+ + HAS_MICROSTEPS = src_filter=+ (ESP3D_)?WIFISUPPORT = AsyncTCP, ESP Async WebServer - ESP3DLib=https://github.com/eduard-sukharev/ESP3DLib/archive/patch-1.zip + ESP3DLib=https://github.com/luc-github/ESP3DLib/archive/master.zip arduinoWebSockets=links2004/WebSockets@2.3.4 luc-github/ESP32SSDP@1.1.1 lib_ignore=ESPAsyncTCP diff --git a/ini/stm32f1.ini b/ini/stm32f1.ini index e90cc9a10d..5cc1c32866 100644 --- a/ini/stm32f1.ini +++ b/ini/stm32f1.ini @@ -188,6 +188,16 @@ monitor_speed = 115200 debug_tool = stlink upload_protocol = stlink +# +# Creality 512K (STM32F103VE) +# +[env:STM32F103VE_creality] +extends = STM32F103Rx_creality +board = genericSTM32F103VE +board_build.variant = MARLIN_F103Vx +build_flags = ${stm32_variant.build_flags} + -DSS_TIMER=4 -DTIMER_SERVO=TIM5 + -DENABLE_HWSERIAL3 -DTRANSFER_CLOCK_DIV=8 # # BigTreeTech SKR Mini E3 V2.0 & DIP / SKR CR6 (STM32F103RET6 ARM Cortex-M3) # diff --git a/ini/stm32f4.ini b/ini/stm32f4.ini index b0d2a5600c..471e9e7fb4 100644 --- a/ini/stm32f4.ini +++ b/ini/stm32f4.ini @@ -47,7 +47,6 @@ board = marlin_STM32F407ZGT6 board_build.variant = MARLIN_FLY_F407ZG board_build.offset = 0x8000 upload_protocol = dfu - # # FYSETC S6 (STM32F446RET6 ARM Cortex-M4) # @@ -684,3 +683,19 @@ build_flags = ${stm32_variant.build_flags} -DSTEP_TIMER_IRQ_PRIO=0 upload_protocol = stlink debug_tool = stlink + +# +# MKS SKIPR v1.0 all-in-one board (STM32F407VE) +# +[env:mks_skipr_v1] +extends = stm32_variant +board = marlin_MKS_SKIPR_V1 +board_build.rename = mks_skipr.bin + +[env:mks_skipr_v1_nobootloader] +extends = env:mks_skipr_v1 +board_build.rename = firmware.bin +board_build.offset = 0x0000 +board_upload.offset_address = 0x08000000 +upload_protocol = dfu +upload_command = dfu-util -a 0 -s 0x08000000:leave -D "$SOURCE"