Configuration updates
This commit is contained in:
InsanityAutomation
@@ -359,7 +359,7 @@
|
||||
#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
|
||||
#define PID_K1 0.95 // Smoothing factor within any PID loop
|
||||
#if ENABLED(PIDTEMP)
|
||||
//#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
|
||||
#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
|
||||
//#define PID_DEBUG // Sends debug data to the serial port.
|
||||
//#define PID_OPENLOOP 1 // Puts PID in open loop. M104/M140 sets the output power from 0 to PID_MAX
|
||||
//#define SLOW_PWM_HEATERS // PWM with very low frequency (roughly 0.125Hz=8s) and minimum state time of approximately 1s useful for heaters driven by a relay
|
||||
@@ -404,7 +404,7 @@
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
@@ -551,7 +551,7 @@
|
||||
* Override with M92
|
||||
* X, Y, Z, E0 [, E1[, E2[, E3[, E4]]]]
|
||||
*/
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT {80, 80, 400, 107.2 }
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT {160, 160, 800, 215.4 }
|
||||
|
||||
/**
|
||||
* Default Max Feed Rate (mm/s)
|
||||
@@ -754,7 +754,7 @@
|
||||
#define Z_PROBE_OFFSET_RANGE_MAX 20
|
||||
|
||||
// Enable the M48 repeatability test to test probe accuracy
|
||||
//#define Z_MIN_PROBE_REPEATABILITY_TEST
|
||||
#define Z_MIN_PROBE_REPEATABILITY_TEST
|
||||
|
||||
// For Inverting Stepper Enable Pins (Active Low) use 0, Non Inverting (Active High) use 1
|
||||
// :{ 0:'Low', 1:'High' }
|
||||
@@ -850,7 +850,7 @@
|
||||
#endif
|
||||
|
||||
#if ENABLED(MIN_SOFTWARE_ENDSTOPS) || ENABLED(MAX_SOFTWARE_ENDSTOPS)
|
||||
//#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD
|
||||
#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD
|
||||
#endif
|
||||
|
||||
/**
|
||||
@@ -861,7 +861,7 @@
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
* By default the firmware assumes HIGH=FILAMENT PRESENT.
|
||||
*/
|
||||
#define FILAMENT_RUNOUT_SENSOR
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
#define FIL_RUNOUT_INVERTING true // set to true to invert the logic of the sensor.
|
||||
@@ -944,7 +944,7 @@
|
||||
/**
|
||||
* Enable the G26 Mesh Validation Pattern tool.
|
||||
*/
|
||||
//#define G26_MESH_VALIDATION
|
||||
#define G26_MESH_VALIDATION
|
||||
#if ENABLED(G26_MESH_VALIDATION)
|
||||
#define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
|
||||
#define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for the G26 Mesh Validation Tool.
|
||||
@@ -1055,7 +1055,7 @@
|
||||
* Commands to execute at the end of G29 probing.
|
||||
* Useful to retract or move the Z probe out of the way.
|
||||
*/
|
||||
//#define Z_PROBE_END_SCRIPT "G1 Z10 F12000\nG1 X15 Y330\nG1 Z0.5\nG1 Z10"
|
||||
#define Z_PROBE_END_SCRIPT "M280 P0 S90"
|
||||
|
||||
|
||||
// @section homing
|
||||
|
||||
+13
-13
@@ -75,8 +75,8 @@
|
||||
* THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
|
||||
*/
|
||||
#if ENABLED(THERMAL_PROTECTION_HOTENDS)
|
||||
#define THERMAL_PROTECTION_PERIOD 40 // Seconds
|
||||
#define THERMAL_PROTECTION_HYSTERESIS 2 // Degrees Celsius
|
||||
#define THERMAL_PROTECTION_PERIOD 120 // Seconds
|
||||
#define THERMAL_PROTECTION_HYSTERESIS 5 // Degrees Celsius
|
||||
|
||||
/**
|
||||
* Whenever an M104, M109, or M303 increases the target temperature, the
|
||||
@@ -90,8 +90,8 @@
|
||||
* and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set
|
||||
* below 2.
|
||||
*/
|
||||
#define WATCH_TEMP_PERIOD 40 // Seconds
|
||||
#define WATCH_TEMP_INCREASE 2 // Degrees Celsius
|
||||
#define WATCH_TEMP_PERIOD 120 // Seconds
|
||||
#define WATCH_TEMP_INCREASE 5 // Degrees Celsius
|
||||
#endif
|
||||
|
||||
/**
|
||||
@@ -104,7 +104,7 @@
|
||||
/**
|
||||
* As described above, except for the bed (M140/M190/M303).
|
||||
*/
|
||||
#define WATCH_BED_TEMP_PERIOD 60 // Seconds
|
||||
#define WATCH_BED_TEMP_PERIOD 120 // Seconds
|
||||
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
|
||||
#endif
|
||||
|
||||
@@ -134,7 +134,7 @@
|
||||
#endif
|
||||
|
||||
// Show extra position information in M114
|
||||
//#define M114_DETAIL
|
||||
#define M114_DETAIL
|
||||
|
||||
// Show Temperature ADC value
|
||||
// Enable for M105 to include ADC values read from temperature sensors.
|
||||
@@ -269,7 +269,7 @@
|
||||
|
||||
// If you want endstops to stay on (by default) even when not homing
|
||||
// enable this option. Override at any time with M120, M121.
|
||||
//#define ENDSTOPS_ALWAYS_ON_DEFAULT
|
||||
#define ENDSTOPS_ALWAYS_ON_DEFAULT
|
||||
|
||||
// @section extras
|
||||
|
||||
@@ -375,7 +375,7 @@
|
||||
//#define HOME_Y_BEFORE_X
|
||||
|
||||
// Enable this if X or Y can't home without homing the other axis first.
|
||||
//#define CODEPENDENT_XY_HOMING
|
||||
#define CODEPENDENT_XY_HOMING
|
||||
|
||||
// @section machine
|
||||
|
||||
@@ -506,10 +506,10 @@
|
||||
#define LCD_TIMEOUT_TO_STATUS 15000
|
||||
|
||||
// Add an 'M73' G-code to set the current percentage
|
||||
//#define LCD_SET_PROGRESS_MANUALLY
|
||||
#define LCD_SET_PROGRESS_MANUALLY
|
||||
|
||||
#if ENABLED(SDSUPPORT) || ENABLED(LCD_SET_PROGRESS_MANUALLY)
|
||||
//#define LCD_PROGRESS_BAR // Show a progress bar on HD44780 LCDs for SD printing
|
||||
#define LCD_PROGRESS_BAR // Show a progress bar on HD44780 LCDs for SD printing
|
||||
#if ENABLED(LCD_PROGRESS_BAR)
|
||||
#define PROGRESS_BAR_BAR_TIME 2000 // (ms) Amount of time to show the bar
|
||||
#define PROGRESS_BAR_MSG_TIME 3000 // (ms) Amount of time to show the status message
|
||||
@@ -714,7 +714,7 @@
|
||||
#if ENABLED(BABYSTEPPING)
|
||||
//#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA!
|
||||
#define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way
|
||||
#define BABYSTEP_MULTIPLICATOR 5 // Babysteps are very small. Increase for faster motion.
|
||||
#define BABYSTEP_MULTIPLICATOR 20 // Babysteps are very small. Increase for faster motion.
|
||||
#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
|
||||
#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
|
||||
#define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
|
||||
@@ -740,7 +740,7 @@
|
||||
* See http://marlinfw.org/docs/features/lin_advance.html for full instructions.
|
||||
* Mention @Sebastianv650 on GitHub to alert the author of any issues.
|
||||
*/
|
||||
//#define LIN_ADVANCE
|
||||
#define LIN_ADVANCE
|
||||
#if ENABLED(LIN_ADVANCE)
|
||||
#define LIN_ADVANCE_K 0.22 // Unit: mm compression per 1mm/s extruder speed
|
||||
//#define LA_DEBUG // If enabled, this will generate debug information output over USB.
|
||||
@@ -896,7 +896,7 @@
|
||||
* 'M106 P<fan> T2' : Use the set secondary speed
|
||||
* 'M106 P<fan> T1' : Restore the previous fan speed
|
||||
*/
|
||||
//#define EXTRA_FAN_SPEED
|
||||
#define EXTRA_FAN_SPEED
|
||||
|
||||
/**
|
||||
* Advanced Pause
|
||||
|
||||
Reference in New Issue
Block a user