Update Configuration_adv.h
This commit is contained in:
InsanityAutomation
committed by
GitHub
GitHub
parent
0ab3f7e985
commit
0858670828
+159
-87
@@ -75,7 +75,7 @@
|
||||
* THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
|
||||
*/
|
||||
#if ENABLED(THERMAL_PROTECTION_HOTENDS)
|
||||
#define THERMAL_PROTECTION_PERIOD 40 // Seconds
|
||||
#define THERMAL_PROTECTION_PERIOD 60 // Seconds
|
||||
#define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius
|
||||
|
||||
/**
|
||||
@@ -90,7 +90,7 @@
|
||||
* and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set
|
||||
* below 2.
|
||||
*/
|
||||
#define WATCH_TEMP_PERIOD 20 // Seconds
|
||||
#define WATCH_TEMP_PERIOD 50 // Seconds
|
||||
#define WATCH_TEMP_INCREASE 2 // Degrees Celsius
|
||||
#endif
|
||||
|
||||
@@ -98,13 +98,13 @@
|
||||
* Thermal Protection parameters for the bed are just as above for hotends.
|
||||
*/
|
||||
#if ENABLED(THERMAL_PROTECTION_BED)
|
||||
#define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds
|
||||
#define THERMAL_PROTECTION_BED_PERIOD 30 // Seconds
|
||||
#define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
|
||||
|
||||
/**
|
||||
* As described above, except for the bed (M140/M190/M303).
|
||||
*/
|
||||
#define WATCH_BED_TEMP_PERIOD 60 // Seconds
|
||||
#define WATCH_BED_TEMP_PERIOD 120 // Seconds
|
||||
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
|
||||
#endif
|
||||
|
||||
@@ -128,14 +128,17 @@
|
||||
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
||||
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
||||
*/
|
||||
#if(!ENABLED(MachineCR10Orig))
|
||||
#define AUTOTEMP
|
||||
#endif
|
||||
#if ENABLED(AUTOTEMP)
|
||||
#define AUTOTEMP_OLDWEIGHT 0.98
|
||||
#endif
|
||||
|
||||
// Show extra position information in M114
|
||||
//#define M114_DETAIL
|
||||
|
||||
#if(!ENABLED(MachineCR10Orig))
|
||||
#define M114_DETAIL
|
||||
#endif
|
||||
// Show Temperature ADC value
|
||||
// Enable for M105 to include ADC values read from temperature sensors.
|
||||
//#define SHOW_TEMP_ADC_VALUES
|
||||
@@ -196,7 +199,7 @@
|
||||
*/
|
||||
//#define USE_CONTROLLER_FAN
|
||||
#if ENABLED(USE_CONTROLLER_FAN)
|
||||
//#define CONTROLLER_FAN_PIN -1 // Set a custom pin for the controller fan
|
||||
//#define CONTROLLER_FAN_PIN FAN1_PIN // Set a custom pin for the controller fan
|
||||
#define CONTROLLERFAN_SECS 60 // Duration in seconds for the fan to run after all motors are disabled
|
||||
#define CONTROLLERFAN_SPEED 255 // 255 == full speed
|
||||
#endif
|
||||
@@ -204,7 +207,8 @@
|
||||
// When first starting the main fan, run it at full speed for the
|
||||
// given number of milliseconds. This gets the fan spinning reliably
|
||||
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
|
||||
//#define FAN_KICKSTART_TIME 100
|
||||
|
||||
#define FAN_KICKSTART_TIME 100
|
||||
|
||||
// This defines the minimal speed for the main fan, run in PWM mode
|
||||
// to enable uncomment and set minimal PWM speed for reliable running (1-255)
|
||||
@@ -369,7 +373,7 @@
|
||||
#define Y_HOME_BUMP_MM 5
|
||||
#define Z_HOME_BUMP_MM 2
|
||||
#define HOMING_BUMP_DIVISOR { 2, 2, 4 } // Re-Bump Speed Divisor (Divides the Homing Feedrate)
|
||||
//#define QUICK_HOME // If homing includes X and Y, do a diagonal move initially
|
||||
#define QUICK_HOME // If homing includes X and Y, do a diagonal move initially
|
||||
|
||||
// When G28 is called, this option will make Y home before X
|
||||
//#define HOME_Y_BEFORE_X
|
||||
@@ -491,19 +495,23 @@
|
||||
// @section lcd
|
||||
|
||||
// Include a page of printer information in the LCD Main Menu
|
||||
//#define LCD_INFO_MENU
|
||||
|
||||
#if(!ENABLED(MachineCR10Orig))
|
||||
#define LCD_INFO_MENU
|
||||
#endif
|
||||
// Leave out seldom-used LCD menu items to recover some Program Memory
|
||||
//#define SLIM_LCD_MENUS
|
||||
#if(ENABLED(MachineCR10Orig))
|
||||
#define SLIM_LCD_MENUS
|
||||
#endif
|
||||
|
||||
// Scroll a longer status message into view
|
||||
//#define STATUS_MESSAGE_SCROLLING
|
||||
#if(!ENABLED(MachineCR10Orig))
|
||||
#define STATUS_MESSAGE_SCROLLING
|
||||
|
||||
// On the Info Screen, display XY with one decimal place when possible
|
||||
//#define LCD_DECIMAL_SMALL_XY
|
||||
|
||||
#define LCD_DECIMAL_SMALL_XY
|
||||
#endif
|
||||
// The timeout (in ms) to return to the status screen from sub-menus
|
||||
//#define LCD_TIMEOUT_TO_STATUS 15000
|
||||
#define LCD_TIMEOUT_TO_STATUS 15000
|
||||
|
||||
// Add an 'M73' G-code to set the current percentage
|
||||
//#define LCD_SET_PROGRESS_MANUALLY
|
||||
@@ -550,8 +558,9 @@
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
#if(!ENABLED(MachineCR10Orig))
|
||||
#define SDCARD_RATHERRECENTFIRST
|
||||
|
||||
#endif
|
||||
// Add an option in the menu to run all auto#.g files
|
||||
//#define MENU_ADDAUTOSTART
|
||||
|
||||
@@ -578,15 +587,16 @@
|
||||
* - SDSORT_CACHE_NAMES will retain the sorted file listing in RAM. (Expensive!)
|
||||
* - SDSORT_DYNAMIC_RAM only uses RAM when the SD menu is visible. (Use with caution!)
|
||||
*/
|
||||
//#define SDCARD_SORT_ALPHA
|
||||
|
||||
#if(!ENABLED(MachineCR10Orig))
|
||||
#define SDCARD_SORT_ALPHA
|
||||
#endif
|
||||
// SD Card Sorting options
|
||||
#if ENABLED(SDCARD_SORT_ALPHA)
|
||||
#define SDSORT_LIMIT 40 // Maximum number of sorted items (10-256). Costs 27 bytes each.
|
||||
#define FOLDER_SORTING -1 // -1=above 0=none 1=below
|
||||
#define SDSORT_GCODE false // Allow turning sorting on/off with LCD and M34 g-code.
|
||||
#define SDSORT_USES_RAM false // Pre-allocate a static array for faster pre-sorting.
|
||||
#define SDSORT_USES_STACK false // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.)
|
||||
#define SDSORT_USES_RAM true // Pre-allocate a static array for faster pre-sorting.
|
||||
#define SDSORT_USES_STACK true // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.)
|
||||
#define SDSORT_CACHE_NAMES false // Keep sorted items in RAM longer for speedy performance. Most expensive option.
|
||||
#define SDSORT_DYNAMIC_RAM false // Use dynamic allocation (within SD menus). Least expensive option. Set SDSORT_LIMIT before use!
|
||||
#define SDSORT_CACHE_VFATS 2 // Maximum number of 13-byte VFAT entries to use for sorting.
|
||||
@@ -597,7 +607,7 @@
|
||||
//#define LONG_FILENAME_HOST_SUPPORT
|
||||
|
||||
// Enable this option to scroll long filenames in the SD card menu
|
||||
//#define SCROLL_LONG_FILENAMES
|
||||
#define SCROLL_LONG_FILENAMES
|
||||
|
||||
/**
|
||||
* This option allows you to abort SD printing when any endstop is triggered.
|
||||
@@ -634,7 +644,7 @@
|
||||
*/
|
||||
#if ENABLED(DOGLCD)
|
||||
// Show SD percentage next to the progress bar
|
||||
//#define DOGM_SD_PERCENT
|
||||
#define DOGM_SD_PERCENT
|
||||
|
||||
// Enable to save many cycles by drawing a hollow frame on the Info Screen
|
||||
#define XYZ_HOLLOW_FRAME
|
||||
@@ -644,8 +654,9 @@
|
||||
|
||||
// A bigger font is available for edit items. Costs 3120 bytes of PROGMEM.
|
||||
// Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
|
||||
//#define USE_BIG_EDIT_FONT
|
||||
|
||||
#if(!ENABLED(MachineCR10Orig))
|
||||
#define USE_BIG_EDIT_FONT
|
||||
#endif
|
||||
// A smaller font may be used on the Info Screen. Costs 2300 bytes of PROGMEM.
|
||||
// Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
|
||||
//#define USE_SMALL_INFOFONT
|
||||
@@ -700,16 +711,20 @@
|
||||
*
|
||||
* Warning: Does not respect endstops!
|
||||
*/
|
||||
//#define BABYSTEPPING
|
||||
#define BABYSTEPPING
|
||||
#if ENABLED(BABYSTEPPING)
|
||||
//#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA!
|
||||
#define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way
|
||||
#define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion.
|
||||
//#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
|
||||
//#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
|
||||
#if(ENABLED(ABL_EZABL) || ENABLED(ABL_BLTOUCH))
|
||||
#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
|
||||
//#if(!ENABLED(MachineCR10Orig))
|
||||
#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
|
||||
// #endif
|
||||
#endif
|
||||
#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
|
||||
#define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
|
||||
// Note: Extra time may be added to mitigate controller latency.
|
||||
//#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
|
||||
#endif
|
||||
|
||||
// @section extruder
|
||||
@@ -730,19 +745,53 @@
|
||||
* See http://marlinfw.org/docs/features/lin_advance.html for full instructions.
|
||||
* Mention @Sebastianv650 on GitHub to alert the author of any issues.
|
||||
*/
|
||||
//#define LIN_ADVANCE
|
||||
#if(!ENABLED(MachineCR10Orig))
|
||||
#define LIN_ADVANCE
|
||||
#endif
|
||||
#if ENABLED(LIN_ADVANCE)
|
||||
#define LIN_ADVANCE_K 0.22 // Unit: mm compression per 1mm/s extruder speed
|
||||
#define LIN_ADVANCE_K 0.5 // Unit: mm compression per 1mm/s extruder speed
|
||||
//#define LA_DEBUG // If enabled, this will generate debug information output over USB.
|
||||
#endif
|
||||
|
||||
// @section leveling
|
||||
|
||||
#if ENABLED(DELTA) && !defined(DELTA_PROBEABLE_RADIUS)
|
||||
#define DELTA_PROBEABLE_RADIUS DELTA_PRINTABLE_RADIUS
|
||||
#elif IS_SCARA && !defined(SCARA_PRINTABLE_RADIUS)
|
||||
#define SCARA_PRINTABLE_RADIUS (SCARA_LINKAGE_1 + SCARA_LINKAGE_2)
|
||||
#endif
|
||||
|
||||
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
|
||||
// Override the mesh area if the automatic (max) area is too large
|
||||
//#define MESH_MIN_X MESH_INSET
|
||||
|
||||
#if( (X_PROBE_OFFSET_FROM_EXTRUDER + 15) > 0 )
|
||||
#define MESH_MIN_X (X_PROBE_OFFSET_FROM_EXTRUDER + 5)
|
||||
#else
|
||||
#define MESH_MIN_X 10
|
||||
#endif
|
||||
|
||||
#if( (X_BED_SIZE + X_PROBE_OFFSET_FROM_EXTRUDER - 10) < X_BED_SIZE)
|
||||
#define MESH_MAX_X (X_BED_SIZE + X_PROBE_OFFSET_FROM_EXTRUDER - 5)
|
||||
#else
|
||||
#define MESH_MAX_X (X_BED_SIZE - 10)
|
||||
#endif
|
||||
|
||||
#if ( (Y_PROBE_OFFSET_FROM_EXTRUDER + 25) > 10 )
|
||||
#define MESH_MIN_Y (Y_PROBE_OFFSET_FROM_EXTRUDER + 25)
|
||||
#else
|
||||
#define MESH_MIN_Y 25
|
||||
#endif
|
||||
|
||||
#if( (Y_BED_SIZE + Y_PROBE_OFFSET_FROM_EXTRUDER - 25) < Y_BED_SIZE)
|
||||
#define MESH_MAX_Y (Y_BED_SIZE + Y_PROBE_OFFSET_FROM_EXTRUDER - 25)
|
||||
#else
|
||||
#define MESH_MAX_Y (Y_BED_SIZE - 25)
|
||||
#endif
|
||||
|
||||
|
||||
//#define MESH_MIN_X 0 - X_PROBE_OFFSET_FROM_EXTRUDER
|
||||
//#define MESH_MIN_Y MESH_INSET
|
||||
//#define MESH_MAX_X X_BED_SIZE - (MESH_INSET)
|
||||
//#define MESH_MAX_X X_BED_SIZE - 5
|
||||
//#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
|
||||
#endif
|
||||
|
||||
@@ -751,7 +800,9 @@
|
||||
//
|
||||
// G2/G3 Arc Support
|
||||
//
|
||||
#if(!ENABLED(MachineCR10Orig))
|
||||
#define ARC_SUPPORT // Disable this feature to save ~3226 bytes
|
||||
#endif
|
||||
#if ENABLED(ARC_SUPPORT)
|
||||
#define MM_PER_ARC_SEGMENT 1 // Length of each arc segment
|
||||
#define N_ARC_CORRECTION 25 // Number of intertpolated segments between corrections
|
||||
@@ -790,11 +841,9 @@
|
||||
|
||||
// The number of linear motions that can be in the plan at any give time.
|
||||
// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2 (e.g. 8, 16, 32) because shifts and ors are used to do the ring-buffering.
|
||||
#if ENABLED(SDSUPPORT)
|
||||
#define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller
|
||||
#else
|
||||
|
||||
#define BLOCK_BUFFER_SIZE 16 // maximize block buffer
|
||||
#endif
|
||||
|
||||
|
||||
// @section serial
|
||||
|
||||
@@ -837,7 +886,7 @@
|
||||
// enter the serial receive buffer, so they cannot be blocked.
|
||||
// Currently handles M108, M112, M410
|
||||
// Does not work on boards using AT90USB (USBCON) processors!
|
||||
//#define EMERGENCY_PARSER
|
||||
#define EMERGENCY_PARSER
|
||||
|
||||
// Bad Serial-connections can miss a received command by sending an 'ok'
|
||||
// Therefore some clients abort after 30 seconds in a timeout.
|
||||
@@ -846,8 +895,9 @@
|
||||
//#define NO_TIMEOUTS 1000 // Milliseconds
|
||||
|
||||
// Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary.
|
||||
//#define ADVANCED_OK
|
||||
|
||||
#if(!ENABLED(MachineCR10Orig))
|
||||
#define ADVANCED_OK
|
||||
#endif
|
||||
// @section extras
|
||||
|
||||
/**
|
||||
@@ -898,43 +948,44 @@
|
||||
* Requires NOZZLE_PARK_FEATURE.
|
||||
* This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
|
||||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
|
||||
#define ADVANCED_PAUSE_FEATURE
|
||||
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 4 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 41 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 430 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 30 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 430 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 20 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 4 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 0 // (mm) An unretract is done, then this length is purged.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 3 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
@@ -1021,19 +1072,6 @@
|
||||
* You may also use software SPI if you wish to use general purpose IO pins.
|
||||
*/
|
||||
//#define HAVE_TMC2130
|
||||
#if ENABLED(HAVE_TMC2130) // Choose your axes here. This is mandatory!
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
|
||||
@@ -1046,7 +1084,22 @@
|
||||
* (https://github.com/teemuatlut/TMC2208Stepper).
|
||||
*/
|
||||
//#define HAVE_TMC2208
|
||||
#if ENABLED(HAVE_TMC2208) // Choose your axes here. This is mandatory!
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
|
||||
// CHOOSE YOUR MOTORS HERE, THIS IS MANDATORY
|
||||
//#define X_IS_TMC2130
|
||||
//#define X2_IS_TMC2130
|
||||
//#define Y_IS_TMC2130
|
||||
//#define Y2_IS_TMC2130
|
||||
//#define Z_IS_TMC2130
|
||||
//#define Z2_IS_TMC2130
|
||||
//#define E0_IS_TMC2130
|
||||
//#define E1_IS_TMC2130
|
||||
//#define E2_IS_TMC2130
|
||||
//#define E3_IS_TMC2130
|
||||
//#define E4_IS_TMC2130
|
||||
|
||||
//#define X_IS_TMC2208
|
||||
//#define X2_IS_TMC2208
|
||||
//#define Y_IS_TMC2208
|
||||
@@ -1058,9 +1111,10 @@
|
||||
//#define E2_IS_TMC2208
|
||||
//#define E3_IS_TMC2208
|
||||
//#define E4_IS_TMC2208
|
||||
#endif
|
||||
|
||||
#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
|
||||
/**
|
||||
* Stepper driver settings
|
||||
*/
|
||||
|
||||
#define R_SENSE 0.11 // R_sense resistor for SilentStepStick2130
|
||||
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
|
||||
@@ -1407,8 +1461,9 @@
|
||||
/**
|
||||
* M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins
|
||||
*/
|
||||
//#define PINS_DEBUGGING
|
||||
|
||||
#if(!ENABLED(MachineCR10Orig))
|
||||
#define PINS_DEBUGGING
|
||||
#endif
|
||||
/**
|
||||
* Auto-report temperatures with M155 S<seconds>
|
||||
*/
|
||||
@@ -1417,8 +1472,9 @@
|
||||
/**
|
||||
* Include capabilities in M115 output
|
||||
*/
|
||||
#if(!ENABLED(MachineCR10Orig))
|
||||
#define EXTENDED_CAPABILITIES_REPORT
|
||||
|
||||
#endif
|
||||
/**
|
||||
* Disable all Volumetric extrusion options
|
||||
*/
|
||||
@@ -1461,26 +1517,42 @@
|
||||
/**
|
||||
* User-defined menu items that execute custom GCode
|
||||
*/
|
||||
//#define CUSTOM_USER_MENUS
|
||||
#if(ENABLED(ABL_UBL))
|
||||
#define CUSTOM_USER_MENUS
|
||||
#endif
|
||||
|
||||
#if ENABLED(CUSTOM_USER_MENUS)
|
||||
#define USER_SCRIPT_DONE "M117 User Script Done"
|
||||
//#define USER_SCRIPT_DONE "M117 User Script Done"
|
||||
#define USER_SCRIPT_AUDIBLE_FEEDBACK
|
||||
//#define USER_SCRIPT_RETURN // Return to status screen after a script
|
||||
#define USER_SCRIPT_RETURN // Return to status screen after a script
|
||||
|
||||
#define USER_DESC_1 "Home & UBL Info"
|
||||
#define USER_GCODE_1 "G28\nG29 W"
|
||||
#if ENABLED(BedDC)
|
||||
#define USER_DESC_1 "UBL Commission Step 1"
|
||||
#define USER_GCODE_1 "M502 \n M500 \n M501 \n M190 S55 \n M104 S225 \n G28 \n G29 P1 \n G29 S1 \n M117 Run Step 2 \n"
|
||||
|
||||
#define USER_DESC_2 "UBL Commission Step 2"
|
||||
#define USER_GCODE_2 "G29 S1 \n G29 S0 \n G29 F 10.0 \n G29 A \n M500 \n G28 \n G29 L1 \n M109 S225 \n G1 X150 Y 150 \n G1 Z0 \n M117 Set Z Offset \n"
|
||||
|
||||
#define USER_DESC_2 "Preheat for PLA"
|
||||
#define USER_GCODE_2 "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND)
|
||||
#define USER_DESC_3 "Prep for Z Adjust"
|
||||
#define USER_GCODE_3 "M190 55 \n M104 235 \n G28 \n G29 L1 \n G1 X150 Y 150 \n G1 Z0"
|
||||
#endif
|
||||
|
||||
#if ENABLED(BedAC)
|
||||
#define USER_DESC_1 "UBL Commission Step 1"
|
||||
#define USER_GCODE_1 "M502 \n M500 \n M501 \n M190 S75 \n M104 S225 \n G28 \n G29 P1 \n G29 S1 \n M117 Run Step 2 \n"
|
||||
|
||||
#define USER_DESC_2 "UBL Commission Step 2"
|
||||
#define USER_GCODE_2 "G29 S1 \n G29 S0 \n G29 F 10.0 \n G29 A \n M500 \n G28 \n G29 L1 \n M109 S225 \n G1 X150 Y 150 \n G1 Z0 \n M117 Set Z Offset \n"
|
||||
|
||||
#define USER_DESC_3 "Preheat for ABS"
|
||||
#define USER_GCODE_3 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND)
|
||||
#define USER_DESC_3 "Prep for Z Adjust"
|
||||
#define USER_GCODE_3 "M190 75 \n M104 235 \n G28 \n G29 L1 \n G1 X150 Y 150 \n G1 Z0 \n"
|
||||
#endif
|
||||
|
||||
#define USER_DESC_4 "Heat Bed/Home/Level"
|
||||
#define USER_GCODE_4 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29"
|
||||
#define USER_DESC_4 "Fill Mesh Points"
|
||||
#define USER_GCODE_4 "G29 P3 \n G29 P3 \n G29 P3 \n G29 T \n"
|
||||
|
||||
#define USER_DESC_5 "Home & Info"
|
||||
#define USER_GCODE_5 "G28\nM503"
|
||||
#define USER_DESC_5 "Run Mesh Validation"
|
||||
#define USER_GCODE_5 "G26 \n"
|
||||
#endif
|
||||
|
||||
/**
|
||||
@@ -1495,8 +1567,8 @@
|
||||
* Will be sent in the form '//action:ACTION_ON_PAUSE', e.g. '//action:pause'.
|
||||
* The host must be configured to handle the action command.
|
||||
*/
|
||||
//#define ACTION_ON_PAUSE "pause"
|
||||
//#define ACTION_ON_RESUME "resume"
|
||||
#define ACTION_ON_PAUSE "pause"
|
||||
#define ACTION_ON_RESUME "resume"
|
||||
|
||||
//===========================================================================
|
||||
//====================== I2C Position Encoder Settings ======================
|
||||
|
||||
Reference in New Issue
Block a user