jessikitty/Marlin
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity

Bump to current

Browse Source
This commit is contained in:
InsanityAutomation
2024-04-15 14:16:11 -04:00
parent 9a570b23a3
commit 11ae89e290
4 changed files with 663 additions and 235 deletions
Download Patch File Download Diff File Expand all files Collapse all files
Marlin/Configuration.h
+339 -108
View File
@@ -1,3 +1,50 @@
// If you have a trex 3, stock is this option plus 2208 on all axis. None in spreadcycle.
#define TREX3
// If you have a trex 3 that was upgraded from a 2+ with the kit, modifies home position and offsets.
//#define TREX3_UPGRADE
//Stock 2+ X is a 4988, all options off defaults to this
//#define X_2208
//#define X_Spreadcycle
//#define X_S109
// Y all options off defaults to 2+ 8825 / 3 2208
//#define Y_2208 // Highly recommended as large prints with high mass can cause layer shifts with stealthchop at high speed
//#define Y_Spreadcycle
//#define Y_4988 // Some machines shipped with 4988 drivers across the board. Set this if you arent sure what you have and all the drivers look identical
//#define Y_S109
//Stock 2+ Z is a 8825, all options off defaults to this
//#define Z_2208 // NOT Recommended! Dual stepper current draw is above the recommended limit for this driver
//#define Z_4988 // Some machines shipped with 4988 drivers across the board. Set this if you arent sure what you have and all the drivers look identical
//#define Z_Spreadcycle
//#define Z_S109
//Stock 2+ Z is a 4988, all options off defaults to this
//#define E_2208 // Not Recommended! Stealthchop mode faults with linear advance
//#define E_Spreadcycle
//#define E_S109
#define BedAC
#define tallVersion
#define ABL_Bilinear
/*
* Enables a filament sensor plugged into the laser pin. Disables the laser
*/
//#define FilamentSensor // Standard older TM3D runout sensor
//#define lerdgeFilSensor // Newer inverted logic TM3D Runout Sensor
//#define filamentEncoder
//#define autoCalibrationKit
//#define SKR12Pro
//////////////////////////////////DO not edit below here unless you know what youre doing! //////////////////////////////////
/**
* Marlin 3D Printer Firmware
* Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
@@ -21,6 +68,22 @@
*/
#pragma once
// The TREX2+ upgraded to the 3 enables most of the same options, simplify here
#if ENABLED(TREX3_UPGRADE)
#define TREX3
#endif
#if ENABLED(TREX3)
#if DISABLED(X_S109)
#define X_2208
#endif
#if DISABLED(Y_S109)
#define Y_2208
#endif
#define Z_2208
#define E_2208
#endif
/**
* Configuration.h
*
@@ -61,14 +124,20 @@
// @section info
// Author info of this build printed to the host during boot and M115
#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
//#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
#define STRING_CONFIG_H_AUTHOR "Tinymachines3D" // Who made the changes.
#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
// @section machine
// Choose the name from boards.h that matches your setup
#ifndef MOTHERBOARD
#define MOTHERBOARD BOARD_RAMPS_14_EFB
#if ENABLED(SKR12Pro)
#define MOTHERBOARD BOARD_BTT_SKR_PRO_V1_2
#elif ENABLED(TREX3)
#define MOTHERBOARD BOARD_FORMBOT_TREX3
#else
#define MOTHERBOARD BOARD_FORMBOT_TREX2PLUS
#endif
#endif
/**
@@ -79,7 +148,11 @@
*
* :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
*/
#define SERIAL_PORT 0
#if ENABLED(SKR12Pro)
#define SERIAL_PORT -1
#else
#define SERIAL_PORT 0
#endif
/**
* Serial Port Baud Rate
@@ -101,7 +174,9 @@
* Currently Ethernet (-2) is only supported on Teensy 4.1 boards.
* :[-2, -1, 0, 1, 2, 3, 4, 5, 6, 7]
*/
//#define SERIAL_PORT_2 -1
#if ENABLED(SKR12Pro)
#define SERIAL_PORT_2 1
#endif
//#define BAUDRATE_2 250000 // :[2400, 9600, 19200, 38400, 57600, 115200, 250000, 500000, 1000000] Enable to override BAUDRATE
/**
@@ -115,8 +190,15 @@
// Enable the Bluetooth serial interface on AT90USB devices
//#define BLUETOOTH
// Name displayed in the LCD "Ready" message and Info menu
//#define CUSTOM_MACHINE_NAME "3D Printer"
// Optional custom name for your RepStrap or other custom machine
// Displayed in the LCD "Ready" message
#if ENABLED(TREX3_UPGRADE)
#define CUSTOM_MACHINE_TIME "T-REX 3(u)"
#elif ENABLED(TREX3)
#define CUSTOM_MACHINE_NAME "T-REX 3"
#else
#define CUSTOM_MACHINE_NAME "T-REX 2+"
#endif
// Printer's unique ID, used by some programs to differentiate between machines.
// Choose your own or use a service like https://www.uuidgenerator.net/version4
@@ -139,9 +221,65 @@
* TMC5160, TMC5160_STANDALONE
* :['A4988', 'A5984', 'DRV8825', 'LV8729', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
*/
#define X_DRIVER_TYPE A4988
#define Y_DRIVER_TYPE A4988
#define Z_DRIVER_TYPE A4988
#if ENABLED(SKR12Pro)
#if ENABLED(TMC2209Upgrade)
#define X_DRIVER_TYPE TMC2209
#define X2_DRIVER_TYPE TMC2209
#define Y_DRIVER_TYPE TMC2209
#define Z_DRIVER_TYPE TMC2209
#define E0_DRIVER_TYPE TMC2209
#define E1_DRIVER_TYPE TMC2209
#else
#define X_DRIVER_TYPE TMC2208
#define X2_DRIVER_TYPE TMC2208
#define Y_DRIVER_TYPE TMC2208
#define Z_DRIVER_TYPE TMC2208
#define E0_DRIVER_TYPE TMC2208
#define E1_DRIVER_TYPE TMC2208
#endif
#else
#if ENABLED(X_2208)
#define X_DRIVER_TYPE TMC2208_STANDALONE
#define X2_DRIVER_TYPE TMC2208_STANDALONE
#else
#define X_DRIVER_TYPE A4988
#define X2_DRIVER_TYPE A4988
#endif
#if ENABLED(Y_2208)
#define Y_DRIVER_TYPE TMC2208_STANDALONE
#elif ENABLED(Y_4988)
#define Y_DRIVER_TYPE A4988
#else
#define Y_DRIVER_TYPE DRV8825
#endif
#if ENABLED(Z_2208)
#define Z_DRIVER_TYPE TMC2208_STANDALONE
#elif ENABLED(Z_4988)
#define Z_DRIVER_TYPE A4988
#else
#define Z_DRIVER_TYPE DRV8825
#endif
#if ENABLED(E_2208)
#define E0_DRIVER_TYPE TMC2208_STANDALONE
#define E1_DRIVER_TYPE TMC2208_STANDALONE
#else
#define E0_DRIVER_TYPE DRV8825
#define E1_DRIVER_TYPE DRV8825
#endif
#endif
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
//#define E4_DRIVER_TYPE A4988
//#define E5_DRIVER_TYPE A4988
//#define E6_DRIVER_TYPE A4988
//#define E7_DRIVER_TYPE A4988
//#define X_DRIVER_TYPE A4988
//#define Y_DRIVER_TYPE A4988
//#define Z_DRIVER_TYPE A4988
//#define X2_DRIVER_TYPE A4988
//#define Y2_DRIVER_TYPE A4988
//#define Z2_DRIVER_TYPE A4988
@@ -153,7 +291,7 @@
//#define U_DRIVER_TYPE A4988
//#define V_DRIVER_TYPE A4988
//#define W_DRIVER_TYPE A4988
#define E0_DRIVER_TYPE A4988
//#define E0_DRIVER_TYPE A4988
//#define E1_DRIVER_TYPE A4988
//#define E2_DRIVER_TYPE A4988
//#define E3_DRIVER_TYPE A4988
@@ -208,7 +346,7 @@
// This defines the number of extruders
// :[0, 1, 2, 3, 4, 5, 6, 7, 8]
#define EXTRUDERS 1
#define EXTRUDERS 2
// Generally expected filament diameter (1.75, 2.85, 3.0, ...). Used for Volumetric, Filament Width Sensor, etc.
#define DEFAULT_NOMINAL_FILAMENT_DIA 1.75
@@ -362,7 +500,12 @@
// Offset of the extruders (uncomment if using more than one and relying on firmware to position when changing).
// The offset has to be X=0, Y=0 for the extruder 0 hotend (default extruder).
// For the other hotends it is their distance from the extruder 0 hotend.
//#define HOTEND_OFFSET_X { 0.0, 20.00 } // (mm) relative X-offset for each nozzle
#if ENABLED(TREX3)
#define HOTEND_OFFSET_X {0.0, 438.5} // (mm) relative X-offset for each nozzle
#else
#define HOTEND_OFFSET_X {0.0, 442.0} // (mm) relative X-offset for each nozzle
#endif
//#define HOTEND_OFFSET_Y { 0.0, 5.00 } // (mm) relative Y-offset for each nozzle
//#define HOTEND_OFFSET_Z { 0.0, 0.00 } // (mm) relative Z-offset for each nozzle
@@ -553,15 +696,24 @@
* 998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
* 999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
*/
#define TEMP_SENSOR_0 1
#define TEMP_SENSOR_1 0
#if ENABLED(TREX3)
#define TEMP_SENSOR_0 1047
#define TEMP_SENSOR_1 61
#else
#define TEMP_SENSOR_0 1
#define TEMP_SENSOR_1 1
#endif
#define TEMP_SENSOR_2 0
#define TEMP_SENSOR_3 0
#define TEMP_SENSOR_4 0
#define TEMP_SENSOR_5 0
#define TEMP_SENSOR_6 0
#define TEMP_SENSOR_7 0
#define TEMP_SENSOR_BED 1
#if(ENABLED(BedAC))
#define TEMP_SENSOR_BED 11
#else
#define TEMP_SENSOR_BED 0
#endif
#define TEMP_SENSOR_PROBE 0
#define TEMP_SENSOR_CHAMBER 0
#define TEMP_SENSOR_COOLER 0
@@ -588,14 +740,14 @@
#endif
#if HAS_E_TEMP_SENSOR
#define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#define TEMP_RESIDENCY_TIME 2 // (seconds) Time to wait for hotend to "settle" in M109
#define TEMP_WINDOW 5 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_HYSTERESIS 5 // (°C) Temperature proximity considered "close enough" to the target
#endif
#if TEMP_SENSOR_BED
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_WINDOW 2 // (°C) Temperature proximity for the "temperature reached" timer
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
#endif
@@ -637,8 +789,13 @@
// Above this temperature the heater will be switched off.
// This can protect components from overheating, but NOT from shorts and failures.
// (Use MINTEMP for thermistor short/failure protection.)
#define HEATER_0_MAXTEMP 275
#define HEATER_1_MAXTEMP 275
#if ENABLED(TREX3)
#define HEATER_0_MAXTEMP 350
#define HEATER_1_MAXTEMP 350
#else
#define HEATER_0_MAXTEMP 410
#define HEATER_1_MAXTEMP 295
#endif
#define HEATER_2_MAXTEMP 275
#define HEATER_3_MAXTEMP 275
#define HEATER_4_MAXTEMP 275
@@ -679,19 +836,25 @@
#if ENABLED(PIDTEMP)
//#define PID_DEBUG // Print PID debug data to the serial port. Use 'M303 D' to toggle activation.
//#define PID_PARAMS_PER_HOTEND // Use separate PID parameters for each extruder (useful for mismatched extruders)
#define PID_PARAMS_PER_HOTEND // Use separate PID parameters for each extruder (useful for mismatched extruders)
// Set/get with G-code: M301 E[extruder number, 0-2]
#if ENABLED(PID_PARAMS_PER_HOTEND)
// Specify up to one value per hotend here, according to your setup.
// If there are fewer values, the last one applies to the remaining hotends.
#define DEFAULT_Kp_LIST { 22.20, 22.20 }
#define DEFAULT_Ki_LIST { 1.08, 1.08 }
#define DEFAULT_Kd_LIST { 114.00, 114.00 }
#if ENABLED(TREX3)
#define DEFAULT_Kp_LIST { 14.64, 14.64 }
#define DEFAULT_Ki_LIST { 1.08, 1.08 }
#define DEFAULT_Kd_LIST { 53.36, 53.36 }
#else
#define DEFAULT_Kp_LIST { 22.20, 22.20 }
#define DEFAULT_Ki_LIST { 1.08, 1.08 }
#define DEFAULT_Kd_LIST { 114.00, 114.00 }
#endif
#else
#define DEFAULT_Kp 22.20
#define DEFAULT_Ki 1.08
#define DEFAULT_Kd 114.00
#define DEFAULT_Kp 22.2
#define DEFAULT_Ki 1.08
#define DEFAULT_Kd 114
#endif
#else
#define BANG_MAX 255 // Limit hotend current while in bang-bang mode; 255=full current
@@ -771,7 +934,7 @@
*
* With this option disabled, bang-bang will be used. BED_LIMIT_SWITCHING enables hysteresis.
*/
//#define PIDTEMPBED
#define PIDTEMPBED
#if ENABLED(PIDTEMPBED)
//#define MIN_BED_POWER 0
@@ -842,8 +1005,8 @@
#define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
// is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
//#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
//#define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of flash)
#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of flash)
#define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of flash)
#endif
// @section safety
@@ -1172,7 +1335,7 @@
*/
#define X_MIN_ENDSTOP_HIT_STATE HIGH
#define X_MAX_ENDSTOP_HIT_STATE HIGH
#define Y_MIN_ENDSTOP_HIT_STATE HIGH
#define Y_MIN_ENDSTOP_HIT_STATE LOW
#define Y_MAX_ENDSTOP_HIT_STATE HIGH
#define Z_MIN_ENDSTOP_HIT_STATE HIGH
#define Z_MAX_ENDSTOP_HIT_STATE HIGH
@@ -1192,7 +1355,7 @@
// Enable this feature if all enabled endstop pins are interrupt-capable.
// This will remove the need to poll the interrupt pins, saving many CPU cycles.
//#define ENDSTOP_INTERRUPTS_FEATURE
#define ENDSTOP_INTERRUPTS_FEATURE
/**
* Endstop Noise Threshold
@@ -1229,14 +1392,28 @@
* following movement settings. If fewer factors are given than the
* total number of extruders, the last value applies to the rest.
*/
//#define DISTINCT_E_FACTORS
#define DISTINCT_E_FACTORS
/**
* Default Axis Steps Per Unit (linear=steps/mm, rotational=steps/°)
* Override with M92 (when enabled below)
* X, Y, Z [, I [, J [, K...]]], E0 [, E1[, E2...]]
*/
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 500 }
#if(ENABLED(Y_2208) || ENABLED(Y_4988) || ENABLED(Y_S109))
#define Y_STEPSMM 80
#else
#define Y_STEPSMM 160
#endif
#if(ENABLED(Z_2208) || ENABLED(Z_4988))
#define Z_STEPSMM 800
#else
#define Z_STEPSMM 1600
#endif
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, Y_STEPSMM, Z_STEPSMM, 93, 93 }
/**
* Enable support for M92. Disable to save at least ~530 bytes of flash.
@@ -1248,11 +1425,16 @@
* Override with M203
* X, Y, Z [, I [, J [, K...]]], E0 [, E1[, E2...]]
*/
#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
#if ENABLED(Y_2208) && DISABLED(Y_Spreadcycle)
#define Y_MAXFEED 100
#else
#define Y_MAXFEED 150
#endif
#define DEFAULT_MAX_FEEDRATE { 200, Y_MAXFEED, 8, 75, 75 }
//#define LIMITED_MAX_FR_EDITING // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
#if ENABLED(LIMITED_MAX_FR_EDITING)
#define MAX_FEEDRATE_EDIT_VALUES { 600, 600, 10, 50 } // ...or, set your own edit limits
#define MAX_FEEDRATE_EDIT_VALUES { 300, 200, 15, 150 } // ...or, set your own edit limits
#endif
/**
@@ -1261,11 +1443,11 @@
* Override with M201
* X, Y, Z [, I [, J [, K...]]], E0 [, E1[, E2...]]
*/
#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
#define DEFAULT_MAX_ACCELERATION { 750, 500, 400, 3000, 3000 }
//#define LIMITED_MAX_ACCEL_EDITING // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
#if ENABLED(LIMITED_MAX_ACCEL_EDITING)
#define MAX_ACCEL_EDIT_VALUES { 6000, 6000, 200, 20000 } // ...or, set your own edit limits
#define MAX_ACCEL_EDIT_VALUES { 1500, 1500, 800, 5000 } // ...or, set your own edit limits
#endif
/**
@@ -1276,9 +1458,9 @@
* M204 R Retract Acceleration
* M204 T Travel Acceleration
*/
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
#define DEFAULT_ACCELERATION 500 // X, Y, Z and E acceleration for printing moves
#define DEFAULT_RETRACT_ACCELERATION 2000 // E acceleration for retracts
#define DEFAULT_TRAVEL_ACCELERATION 500 // X, Y, Z acceleration for travel (non printing) moves
/**
* Default Jerk limits (mm/s)
@@ -1288,10 +1470,10 @@
* When changing speed and direction, if the difference is less than the
* value set here, it may happen instantaneously.
*/
//#define CLASSIC_JERK
#define CLASSIC_JERK
#if ENABLED(CLASSIC_JERK)
#define DEFAULT_XJERK 10.0
#define DEFAULT_YJERK 10.0
#define DEFAULT_YJERK 5.0
#define DEFAULT_ZJERK 0.3
#define DEFAULT_EJERK 5.0
//#define DEFAULT_IJERK 0.3
@@ -1305,7 +1487,7 @@
//#define LIMITED_JERK_EDITING // Limit edit via M205 or LCD to DEFAULT_aJERK * 2
#if ENABLED(LIMITED_JERK_EDITING)
#define MAX_JERK_EDIT_VALUES { 20, 20, 0.6, 10 } // ...or, set your own edit limits
#define MAX_JERK_EDIT_VALUES { 20, 20, 0.6, 10, 10 } // ...or, set your own edit limits
#endif
#endif
@@ -1330,7 +1512,7 @@
*
* See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained
*/
//#define S_CURVE_ACCELERATION
#define S_CURVE_ACCELERATION
//===========================================================================
//============================= Z Probe Options =============================
@@ -1406,7 +1588,7 @@
/**
* The BLTouch probe uses a Hall effect sensor and emulates a servo.
*/
//#define BLTOUCH
#define BLTOUCH
/**
* MagLev V4 probe by MDD
@@ -1581,7 +1763,6 @@
* | [-] |
* O-- FRONT --+
*/
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
// Enable and set to use a specific tool for probing. Disable to allow any tool.
#define PROBING_TOOL 0
@@ -1597,7 +1778,7 @@
#define XY_PROBE_FEEDRATE (133*60)
// Feedrate (mm/min) for the first approach when double-probing (MULTIPLE_PROBING == 2)
#define Z_PROBE_FEEDRATE_FAST (4*60)
#define Z_PROBE_FEEDRATE_FAST (10*60)
// Feedrate (mm/min) for the "accurate" probe of each point
#define Z_PROBE_FEEDRATE_SLOW (Z_PROBE_FEEDRATE_FAST / 2)
@@ -1647,7 +1828,7 @@
* A total of 2 does fast/slow probes with a weighted average.
* A total of 3 or more adds more slow probes, taking the average.
*/
//#define MULTIPLE_PROBING 2
#define MULTIPLE_PROBING 2
//#define EXTRA_PROBING 1
/**
@@ -1664,21 +1845,27 @@
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
*/
#define Z_CLEARANCE_DEPLOY_PROBE 10 // (mm) Z Clearance for Deploy/Stow
#if ENABLED(TREX3)
#define NOZZLE_TO_PROBE_OFFSET { -3, 31, 0 }
#else
#define NOZZLE_TO_PROBE_OFFSET { -7, 29, 0 }
#endif
#define Z_CLEARANCE_DEPLOY_PROBE 5 // (mm) Z Clearance for Deploy/Stow
#define Z_CLEARANCE_BETWEEN_PROBES 5 // (mm) Z Clearance between probe points
#define Z_CLEARANCE_MULTI_PROBE 5 // (mm) Z Clearance between multiple probes
#define Z_PROBE_ERROR_TOLERANCE 3 // (mm) Tolerance for early trigger (<= -probe.offset.z + ZPET)
//#define Z_AFTER_PROBING 5 // (mm) Z position after probing is done
#define Z_PROBE_LOW_POINT -2 // (mm) Farthest distance below the trigger-point to go before stopping
#define Z_PROBE_LOW_POINT -3 // (mm) Farthest distance below the trigger-point to go before stopping
// For M851 provide ranges for adjusting the X, Y, and Z probe offsets
//#define PROBE_OFFSET_XMIN -50 // (mm)
//#define PROBE_OFFSET_XMAX 50 // (mm)
//#define PROBE_OFFSET_YMIN -50 // (mm)
//#define PROBE_OFFSET_YMAX 50 // (mm)
//#define PROBE_OFFSET_ZMIN -20 // (mm)
//#define PROBE_OFFSET_ZMAX 20 // (mm)
#define PROBE_OFFSET_ZMIN -3 // (mm)
#define PROBE_OFFSET_ZMAX 3 // (mm)
// Enable the M48 repeatability test to test probe accuracy
//#define Z_MIN_PROBE_REPEATABILITY_TEST
@@ -1749,9 +1936,21 @@
// @section motion
// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
#define INVERT_X_DIR false
#define INVERT_Y_DIR true
#define INVERT_Z_DIR false
#if ANY(X_2208, SKR12Pro)
#define INVERT_X_DIR true
#else
#define INVERT_X_DIR false
#endif
#if ANY(Y_2208, SKR12Pro)
#define INVERT_Y_DIR true
#else
#define INVERT_Y_DIR false
#endif
#if ANY(Z_2208, SKR12Pro)
#define INVERT_Z_DIR false
#else
#define INVERT_Z_DIR true
#endif
//#define INVERT_I_DIR false
//#define INVERT_J_DIR false
//#define INVERT_K_DIR false
@@ -1762,8 +1961,13 @@
// @section extruder
// For direct drive extruder v9 set to true, for geared extruder set to false.
#define INVERT_E0_DIR false
#define INVERT_E1_DIR false
#if ANY(E_2208, SKR12Pro) && DISABLED(TREX3)
#define INVERT_E0_DIR true
#define INVERT_E1_DIR false
#else
#define INVERT_E0_DIR false
#define INVERT_E1_DIR true
#endif
#define INVERT_E2_DIR false
#define INVERT_E3_DIR false
#define INVERT_E4_DIR false
@@ -1794,7 +1998,7 @@
// Direction of endstops when homing; 1=MAX, -1=MIN
// :[-1,1]
#define X_HOME_DIR -1
#define Y_HOME_DIR -1
#define Y_HOME_DIR 1
#define Z_HOME_DIR -1
//#define I_HOME_DIR -1
//#define J_HOME_DIR -1
@@ -1820,17 +2024,29 @@
// @section geometry
// The size of the printable area
#define X_BED_SIZE 200
#define Y_BED_SIZE 200
// The size of the print bed
#define X_BED_SIZE 400
#define Y_BED_SIZE 400
// Travel limits (linear=mm, rotational=°) after homing, corresponding to endstop positions.
#define X_MIN_POS 0
#define Y_MIN_POS 0
#define Z_MIN_POS 0
#define X_MAX_POS X_BED_SIZE
#define Y_MAX_POS Y_BED_SIZE
#define Z_MAX_POS 200
#if DISABLED(TREX3) || ENABLED(TREX3_UPGRADE)
#define X_MIN_POS -42
#define Y_MIN_POS 0
#define Z_MIN_POS -3
#define X_MAX_POS 450
#define Y_MAX_POS Y_BED_SIZE
#else
#define X_MIN_POS -47
#define Y_MIN_POS 0
#define Z_MIN_POS -3
#define X_MAX_POS 460
#define Y_MAX_POS Y_BED_SIZE
#endif
#if(ENABLED(tallVersion))
#define Z_MAX_POS 700
#else
#define Z_MAX_POS 500
#endif
//#define I_MIN_POS 0
//#define I_MAX_POS 50
//#define J_MIN_POS 0
@@ -1882,7 +2098,7 @@
#endif
#if ANY(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS)
//#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD
#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD
#endif
/**
@@ -1893,15 +2109,19 @@
* Marlin knows a print job is running when:
* 1. Running a print job from media started with M24.
* 2. The Print Job Timer has been started with M75.
* 3. The heaters were turned on and PRINTJOB_TIMER_AUTOSTART is enabled.
* 3. The heaters were turned on with a wait command (M109) and PRINTJOB_TIMER_AUTOSTART is enabled.
*
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
*/
//#define FILAMENT_RUNOUT_SENSOR
#define FILAMENT_RUNOUT_SENSOR
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
#define FIL_RUNOUT_ENABLED_DEFAULT true // Enable the sensor on startup. Override with M412 followed by M500.
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
#if ENABLED(TREX3)
#define NUM_RUNOUT_SENSORS 2
#else
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
#endif
#define FIL_RUNOUT_STATE LOW // Pin state indicating that filament is NOT present.
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
@@ -1944,13 +2164,17 @@
// Commands to execute on filament runout.
// With multiple runout sensors use the %c placeholder for the current tool in commands (e.g., "M600 T%c")
// NOTE: After 'M412 H1' the host handles filament runout and this script does not apply.
#define FILAMENT_RUNOUT_SCRIPT "M600"
// NOTE: After 'M591 H1' the host handles filament runout and this script does not apply.
#define FILAMENT_RUNOUT_SCRIPT "M600 %c"
// After a runout is detected, continue printing this length of filament
// before executing the runout script. Useful for a sensor at the end of
// a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead.
//#define FILAMENT_RUNOUT_DISTANCE_MM 25
#if ENABLED(TREX3)
// #define FIL_RUNOUT_DISTANCE_MM { 15, 15 }
#else
// #define FIL_RUNOUT_DISTANCE_MM { 15 }
#endif
#ifdef FILAMENT_RUNOUT_DISTANCE_MM
// Enable this option to use an encoder disc that toggles the runout pin
@@ -2041,8 +2265,11 @@
*/
//#define AUTO_BED_LEVELING_3POINT
//#define AUTO_BED_LEVELING_LINEAR
//#define AUTO_BED_LEVELING_BILINEAR
//#define AUTO_BED_LEVELING_UBL
#if ENABLED(ABL_Bilinear)
#define AUTO_BED_LEVELING_BILINEAR
#else
#define AUTO_BED_LEVELING_UBL
#endif
//#define MESH_BED_LEVELING
/**
@@ -2056,7 +2283,7 @@
* these options to restore the prior leveling state or to always enable
* leveling immediately after G28.
*/
//#define RESTORE_LEVELING_AFTER_G28
#define RESTORE_LEVELING_AFTER_G28
//#define ENABLE_LEVELING_AFTER_G28
/**
@@ -2088,7 +2315,7 @@
*/
#define ENABLE_LEVELING_FADE_HEIGHT
#if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)
#define DEFAULT_LEVELING_FADE_HEIGHT 10.0 // (mm) Default fade height.
#define DEFAULT_LEVELING_FADE_HEIGHT 0.0 // (mm) Default fade height.
#endif
/**
@@ -2102,7 +2329,9 @@
/**
* Enable the G26 Mesh Validation Pattern tool.
*/
//#define G26_MESH_VALIDATION
#if ENABLED(ABL_Bilinear)
#define G26_MESH_VALIDATION
#endif
#if ENABLED(G26_MESH_VALIDATION)
#define MESH_TEST_NOZZLE_SIZE 0.4 // (mm) Diameter of primary nozzle.
#define MESH_TEST_LAYER_HEIGHT 0.2 // (mm) Default layer height for G26.
@@ -2118,7 +2347,7 @@
#if ANY(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR)
// Set the number of grid points per dimension.
#define GRID_MAX_POINTS_X 3
#define GRID_MAX_POINTS_X 11
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
// Probe along the Y axis, advancing X after each column
@@ -2148,13 +2377,13 @@
//========================= Unified Bed Leveling ============================
//===========================================================================
//#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh
#define MESH_EDIT_GFX_OVERLAY // Display a graphics overlay while editing the mesh
#define MESH_INSET 1 // Set Mesh bounds as an inset region of the bed
#define GRID_MAX_POINTS_X 10 // Don't use more than 15 points per axis, implementation limited.
#define MESH_INSET 3 // Set Mesh bounds as an inset region of the bed
#define GRID_MAX_POINTS_X 15 // Don't use more than 15 points per axis, implementation limited.
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
//#define UBL_HILBERT_CURVE // Use Hilbert distribution for less travel when probing multiple points
#define UBL_HILBERT_CURVE // Use Hilbert distribution for less travel when probing multiple points
//#define UBL_TILT_ON_MESH_POINTS // Use nearest mesh points with G29 J for better Z reference
//#define UBL_TILT_ON_MESH_POINTS_3POINT // Use nearest mesh points with G29 J0 (3-point)
@@ -2162,7 +2391,7 @@
#define UBL_MESH_EDIT_MOVES_Z // Sophisticated users prefer no movement of nozzle
#define UBL_SAVE_ACTIVE_ON_M500 // Save the currently active mesh in the current slot on M500
//#define UBL_Z_RAISE_WHEN_OFF_MESH 2.5 // When the nozzle is off the mesh, this value is used
#define UBL_Z_RAISE_WHEN_OFF_MESH 0.0 // When the nozzle is off the mesh, this value is used
// as the Z-Height correction value.
//#define UBL_MESH_WIZARD // Run several commands in a row to get a complete mesh
@@ -2256,7 +2485,7 @@
// For DELTA this is the top-center of the Cartesian print volume.
//#define MANUAL_X_HOME_POS 0
//#define MANUAL_Y_HOME_POS 0
//#define MANUAL_Z_HOME_POS 0
#define MANUAL_Z_HOME_POS 0
//#define MANUAL_I_HOME_POS 0
//#define MANUAL_J_HOME_POS 0
//#define MANUAL_K_HOME_POS 0
@@ -2271,7 +2500,7 @@
* - Allows Z homing only when XY positions are known and trusted.
* - If stepper drivers sleep, XY homing may be required again before Z homing.
*/
//#define Z_SAFE_HOMING
#define Z_SAFE_HOMING
#if ENABLED(Z_SAFE_HOMING)
#define Z_SAFE_HOMING_X_POINT X_CENTER // (mm) X point for Z homing
@@ -2358,13 +2587,13 @@
* M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
* M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
*/
//#define EEPROM_SETTINGS // Persistent storage with M500 and M501
#define EEPROM_SETTINGS // Persistent storage with M500 and M501
//#define DISABLE_M503 // Saves ~2700 bytes of flash. Disable for release!
#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save flash.
#define EEPROM_BOOT_SILENT // Keep M503 quiet and only give errors during first load
#if ENABLED(EEPROM_SETTINGS)
//#define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors.
//#define EEPROM_INIT_NOW // Init EEPROM on first boot after a new build.
#define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors.
#define EEPROM_INIT_NOW // Init EEPROM on first boot after a new build.
#endif
// @section host
@@ -2421,11 +2650,11 @@
* P1 Raise the nozzle always to Z-park height.
* P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
*/
//#define NOZZLE_PARK_FEATURE
#define NOZZLE_PARK_FEATURE
#if ENABLED(NOZZLE_PARK_FEATURE)
// Specify a park position as { X, Y, Z_raise }
#define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
#define NOZZLE_PARK_POINT { 150, (Y_MIN_POS + 10), 10 }
#define NOZZLE_PARK_MOVE 0 // Park motion: 0 = XY Move, 1 = X Only, 2 = Y Only, 3 = X before Y, 4 = Y before X
#define NOZZLE_PARK_Z_RAISE_MIN 2 // (mm) Always raise Z by at least this distance
#define NOZZLE_PARK_XY_FEEDRATE 100 // (mm/s) X and Y axes feedrate (also used for delta Z axis)
@@ -2468,7 +2697,7 @@
*
* Caveats: The ending Z should be the same as starting Z.
*/
//#define NOZZLE_CLEAN_FEATURE
#define NOZZLE_CLEAN_FEATURE
#if ENABLED(NOZZLE_CLEAN_FEATURE)
#define NOZZLE_CLEAN_PATTERN_LINE // Provide 'G12 P0' - a simple linear cleaning pattern
@@ -2478,7 +2707,7 @@
// Default pattern to use when 'P' is not provided to G12. One of the enabled options above.
#define NOZZLE_CLEAN_DEFAULT_PATTERN 0
#define NOZZLE_CLEAN_STROKES 12 // Default number of pattern repetitions
#define NOZZLE_CLEAN_STROKES 4 // Default number of pattern repetitions
#if ENABLED(NOZZLE_CLEAN_PATTERN_ZIGZAG)
#define NOZZLE_CLEAN_TRIANGLES 3 // Default number of triangles
@@ -2486,8 +2715,8 @@
// Specify positions for each tool as { { X, Y, Z }, { X, Y, Z } }
// Dual hotend system may use { { -20, (Y_BED_SIZE / 2), (Z_MIN_POS + 1) }, { 420, (Y_BED_SIZE / 2), (Z_MIN_POS + 1) }}
#define NOZZLE_CLEAN_START_POINT { { 30, 30, (Z_MIN_POS + 1) } }
#define NOZZLE_CLEAN_END_POINT { { 100, 60, (Z_MIN_POS + 1) } }
#define NOZZLE_CLEAN_START_POINT { { -20, (Y_BED_SIZE / 2), (Z_MIN_POS + 1) }, { 420, (Y_BED_SIZE / 2), (Z_MIN_POS + 1) }}
#define NOZZLE_CLEAN_END_POINT { { (-30), (Y_BED_SIZE / 2), (Z_MIN_POS + 1) }, { (430), (Y_BED_SIZE / 2), (Z_MIN_POS + 1) }}
#if ENABLED(NOZZLE_CLEAN_PATTERN_CIRCLE)
#define NOZZLE_CLEAN_CIRCLE_RADIUS 6.5 // (mm) Circular pattern radius
@@ -2498,11 +2727,11 @@
// Move the nozzle to the initial position after cleaning
#define NOZZLE_CLEAN_GOBACK
// For a purge/clean station that's always at the gantry height (thus no Z move)
//#define NOZZLE_CLEAN_NO_Z
// Enable for a purge/clean station that's always at the gantry height (thus no Z move)
#define NOZZLE_CLEAN_NO_Z
// For a purge/clean station mounted on the X axis
//#define NOZZLE_CLEAN_NO_Y
#define NOZZLE_CLEAN_NO_Y
// Require a minimum hotend temperature for cleaning
#define NOZZLE_CLEAN_MIN_TEMP 170
@@ -2648,7 +2877,8 @@
* SD Card support is disabled by default. If your controller has an SD slot,
* you must uncomment the following option or it won't work.
*/
//#define SDSUPPORT
#define SD_SPI_SPEED SPI_HALF_SPEED
#define SDSUPPORT
/**
* SD CARD: ENABLE CRC
@@ -2728,8 +2958,8 @@
//
// Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
//
//#define INDIVIDUAL_AXIS_HOMING_MENU
//#define INDIVIDUAL_AXIS_HOMING_SUBMENU
#define INDIVIDUAL_AXIS_HOMING_MENU
#define INDIVIDUAL_AXIS_HOMING_SUBMENU
//
// SPEAKER/BUZZER
@@ -2931,7 +3161,7 @@
// RepRapDiscount FULL GRAPHIC Smart Controller
// https://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
//
//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
//
// K.3D Full Graphic Smart Controller
@@ -3459,8 +3689,9 @@
// Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
// which is not as annoying as with the hardware PWM. On the other hand, if this frequency
// is too low, you should also increment SOFT_PWM_SCALE.
//#define FAN_SOFT_PWM
#if ENABLED(TREX3) && DISABLED(SKR12Pro)
#define FAN_SOFT_PWM
#endif
// Incrementing this by 1 will double the software PWM frequency,
// affecting heaters, and the fan if FAN_SOFT_PWM is enabled.
// However, control resolution will be halved for each increment;
Marlin/Configuration_adv.h
+157 -127
View File
@@ -304,14 +304,14 @@
* THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
*/
#if ENABLED(THERMAL_PROTECTION_HOTENDS)
#define THERMAL_PROTECTION_PERIOD 40 // (seconds)
#define THERMAL_PROTECTION_HYSTERESIS 4 // (°C)
#define THERMAL_PROTECTION_PERIOD 60 // (seconds)
#define THERMAL_PROTECTION_HYSTERESIS 15 // (°C)
//#define ADAPTIVE_FAN_SLOWING // Slow down the part-cooling fan if the temperature drops
#define ADAPTIVE_FAN_SLOWING // Slow down the part-cooling fan if the temperature drops
#if ENABLED(ADAPTIVE_FAN_SLOWING)
//#define REPORT_ADAPTIVE_FAN_SLOWING // Report fan slowing activity to the console
#if ANY(MPCTEMP, PIDTEMP)
//#define TEMP_TUNING_MAINTAIN_FAN // Don't slow down the fan speed during M303 or M306 T
#define TEMP_TUNING_MAINTAIN_FAN // Don't slow down the fan speed during M303 or M306 T
#endif
#endif
@@ -327,7 +327,7 @@
* and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set
* below 2.
*/
#define WATCH_TEMP_PERIOD 40 // (seconds)
#define WATCH_TEMP_PERIOD 60 // (seconds)
#define WATCH_TEMP_INCREASE 2 // (°C)
#endif
@@ -335,13 +335,13 @@
* Thermal Protection parameters for the bed are just as above for hotends.
*/
#if ENABLED(THERMAL_PROTECTION_BED)
#define THERMAL_PROTECTION_BED_PERIOD 20 // (seconds)
#define THERMAL_PROTECTION_BED_PERIOD 120 // (seconds)
#define THERMAL_PROTECTION_BED_HYSTERESIS 2 // (°C)
/**
* As described above, except for the bed (M140/M190/M303).
*/
#define WATCH_BED_TEMP_PERIOD 60 // (seconds)
#define WATCH_BED_TEMP_PERIOD 120 // (seconds)
#define WATCH_BED_TEMP_INCREASE 2 // (°C)
#endif
@@ -547,9 +547,9 @@
* Hotend Idle Timeout
* Prevent filament in the nozzle from charring and causing a critical jam.
*/
//#define HOTEND_IDLE_TIMEOUT
#define HOTEND_IDLE_TIMEOUT
#if ENABLED(HOTEND_IDLE_TIMEOUT)
#define HOTEND_IDLE_TIMEOUT_SEC (5*60) // (seconds) Time without extruder movement to trigger protection
#define HOTEND_IDLE_TIMEOUT_SEC (15*60) // (seconds) Time without extruder movement to trigger protection
#define HOTEND_IDLE_MIN_TRIGGER 180 // (°C) Minimum temperature to enable hotend protection
#define HOTEND_IDLE_NOZZLE_TARGET 0 // (°C) Safe temperature for the nozzle after timeout
#define HOTEND_IDLE_BED_TARGET 0 // (°C) Safe temperature for the bed after timeout
@@ -602,7 +602,7 @@
* gets it spinning reliably for a short time before setting the requested speed.
* (Does not work on Sanguinololu with FAN_SOFT_PWM.)
*/
//#define FAN_KICKSTART_TIME 100 // (ms)
#define FAN_KICKSTART_TIME 100 // (ms)
//#define FAN_KICKSTART_POWER 180 // 64-255
// Some coolers may require a non-zero "off" state.
@@ -681,8 +681,17 @@
* Multiple extruders can be assigned to the same pin in which case
* the fan will turn on when any selected extruder is above the threshold.
*/
#define E0_AUTO_FAN_PIN -1
#define E1_AUTO_FAN_PIN -1
#if ENABLED(SKR12Pro, TREX3)
#define E0_AUTO_FAN_PIN FAN2_PIN
#define E1_AUTO_FAN_PIN FAN2_PIN
#elif ENABLED(TREX3)
#define E0_AUTO_FAN_PIN 6
#define E1_AUTO_FAN_PIN 45
#else
#define E0_AUTO_FAN_PIN -1
#define E1_AUTO_FAN_PIN -1
#endif
#define E2_AUTO_FAN_PIN -1
#define E3_AUTO_FAN_PIN -1
#define E4_AUTO_FAN_PIN -1
@@ -748,15 +757,17 @@
* @section caselight
* M355 Case Light on-off / brightness
*/
//#define CASE_LIGHT_ENABLE
#define CASE_LIGHT_ENABLE
#if ENABLED(CASE_LIGHT_ENABLE)
//#define CASE_LIGHT_PIN 4 // Override the default pin if needed
#if ENABLED(SKR12Pro)
#define CASE_LIGHT_PIN HEATER_2_PIN // Override the default pin if needed
#endif
#define INVERT_CASE_LIGHT false // Set true if Case Light is ON when pin is LOW
#define CASE_LIGHT_DEFAULT_ON true // Set default power-up state on
#define CASE_LIGHT_DEFAULT_BRIGHTNESS 105 // Set default power-up brightness (0-255, requires PWM pin)
#define CASE_LIGHT_DEFAULT_BRIGHTNESS 255 // Set default power-up brightness (0-255, requires PWM pin)
//#define CASE_LIGHT_NO_BRIGHTNESS // Disable brightness control. Enable for non-PWM lighting.
//#define CASE_LIGHT_MAX_PWM 128 // Limit PWM duty cycle (0-255)
//#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu
#define CASE_LIGHT_MENU // Add Case Light options to the LCD menu
#if ENABLED(NEOPIXEL_LED)
//#define CASE_LIGHT_USE_NEOPIXEL // Use NeoPixel LED as case light
#endif
@@ -815,22 +826,26 @@
* Set the initial X offset and temperature differential with M605 S2 X[offs] R[deg] and
* follow with M605 S3 to initiate mirrored movement.
*/
//#define DUAL_X_CARRIAGE
#define DUAL_X_CARRIAGE
#if ENABLED(DUAL_X_CARRIAGE)
#define X1_MIN_POS X_MIN_POS // Set to X_MIN_POS
#define X1_MAX_POS X_BED_SIZE // A max coordinate so the X1 carriage can't hit the parked X2 carriage
#define X2_MIN_POS 80 // A min coordinate so the X2 carriage can't hit the parked X1 carriage
#define X2_MAX_POS 353 // The max position of the X2 carriage, typically also the home position
#define X2_MIN_POS 0 // A min coordinate so the X2 carriage can't hit the parked X1 carriage
#if DISABLED(TREX3) || ENABLED(TREX3_UPGRADE)
#define X2_MAX_POS 442 // The max position of the X2 carriage, typically also the home position
#else
#define X2_MAX_POS 446 // The max position of the X2 carriage, typically also the home position
#endif
#define X2_HOME_POS X2_MAX_POS // Default X2 home position. Set to X2_MAX_POS.
// NOTE: For Dual X Carriage use M218 T1 Xn to override the X2_HOME_POS.
// This allows recalibration of endstops distance without a rebuild.
// Remember to set the second extruder's X-offset to 0 in your slicer.
// This is the default power-up mode which can be changed later using M605 S<mode>.
// This is the default power-up mode which can be later using M605.
#define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_AUTO_PARK_MODE
// Default x offset in duplication mode (typically set to half print bed width)
#define DEFAULT_DUPLICATION_X_OFFSET 100
#define DEFAULT_DUPLICATION_X_OFFSET 200
// Default action to execute following M605 mode change commands. Typically G28X to apply new mode.
//#define EVENT_GCODE_IDEX_AFTER_MODECHANGE "G28X"
@@ -931,7 +946,7 @@
//#define HOMING_BACKOFF_POST_MM { 2, 2, 2 } // (linear=mm, rotational=°) Backoff from endstops after homing
//#define XY_COUNTERPART_BACKOFF_MM 0 // (mm) Backoff X after homing Y, and vice-versa
//#define QUICK_HOME // If G28 contains XY do a diagonal move first
#define QUICK_HOME // If G28 contains XY do a diagonal move first
//#define HOME_Y_BEFORE_X // If G28 contains XY home Y before X
//#define HOME_Z_FIRST // Home Z first. Requires a real endstop (not a probe).
//#define CODEPENDENT_XY_HOMING // If X/Y can't home without homing Y/X first
@@ -1003,7 +1018,7 @@
*
* Set the default state here, change with 'M401 S' or UI, use M500 to save, M502 to reset.
*/
//#define BLTOUCH_HS_MODE true
#define BLTOUCH_HS_MODE true
#ifdef BLTOUCH_HS_MODE
// The probe Z offset (M851 Z) is the height at which the probe triggers.
@@ -1263,7 +1278,11 @@
// Increase the slowdown divisor for larger buffer sizes.
#define SLOWDOWN
#if ENABLED(SLOWDOWN)
#define SLOWDOWN_DIVISOR 2
#if ENABLED(SKR12Pro)
#define SLOWDOWN_DIVISOR 6
#else
#define SLOWDOWN_DIVISOR 2
#endif
#endif
/**
@@ -1281,12 +1300,12 @@
// Backlash Compensation
// Adds extra movement to axes on direction-changes to account for backlash.
//
//#define BACKLASH_COMPENSATION
#define BACKLASH_COMPENSATION
#if ENABLED(BACKLASH_COMPENSATION)
// Define values for backlash distance and correction.
// If BACKLASH_GCODE is enabled these values are the defaults.
#define BACKLASH_DISTANCE_MM { 0, 0, 0 } // (linear=mm, rotational=°) One value for each linear axis
#define BACKLASH_CORRECTION 0.0 // 0.0 = no correction; 1.0 = full correction
#define BACKLASH_CORRECTION 0.5 // 0.0 = no correction; 1.0 = full correction
// Add steps for motor direction changes on CORE kinematics
//#define CORE_BACKLASH
@@ -1296,11 +1315,11 @@
//#define BACKLASH_SMOOTHING_MM 3 // (mm)
// Add runtime configuration and tuning of backlash values (M425)
//#define BACKLASH_GCODE
#define BACKLASH_GCODE
#if ENABLED(BACKLASH_GCODE)
// Measure the Z backlash when probing (G29) and set with "M425 Z"
#define MEASURE_BACKLASH_WHEN_PROBING
//#define MEASURE_BACKLASH_WHEN_PROBING
#if ENABLED(MEASURE_BACKLASH_WHEN_PROBING)
// When measuring, the probe will move up to BACKLASH_MEASUREMENT_LIMIT
@@ -1326,7 +1345,9 @@
* Note: HOTEND_OFFSET and CALIBRATION_OBJECT_CENTER must be set to within
* ±5mm of true values for G425 to succeed.
*/
//#define CALIBRATION_GCODE
#if ENABLED(autoCalibrationKit)
#define CALIBRATION_GCODE
#endif
#if ENABLED(CALIBRATION_GCODE)
//#define CALIBRATION_SCRIPT_PRE "M117 Starting Auto-Calibration\nT0\nG28\nG12\nM117 Calibrating..."
@@ -1343,11 +1364,13 @@
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm
// Uncomment to enable reporting (required for "G425 V", but consumes flash).
//#define CALIBRATION_REPORTING
#if ENABLED(SKR12Pro)
#define CALIBRATION_REPORTING
#endif
// The true location and dimension the cube/bolt/washer on the bed.
#define CALIBRATION_OBJECT_CENTER { 264.0, -22.0, -2.0 } // mm
#define CALIBRATION_OBJECT_DIMENSIONS { 10.0, 10.0, 10.0 } // mm
#define CALIBRATION_OBJECT_CENTER { 264.0, 25.0, 12.5 } // mm
#define CALIBRATION_OBJECT_DIMENSIONS { 12.55, 12.55, 4.0 } // mm
// Comment out any sides which are unreachable by the probe. For best
// auto-calibration results, all sides must be reachable.
@@ -1371,12 +1394,16 @@
// Probing at the exact top center only works if the center is flat. If
// probing on a screw head or hollow washer, probe near the edges.
//#define CALIBRATION_MEASURE_AT_TOP_EDGES
#define CALIBRATION_MEASURE_AT_TOP_EDGES
// Define the pin to read during calibration
#ifndef CALIBRATION_PIN
//#define CALIBRATION_PIN -1 // Define here to override the default pin
#define CALIBRATION_PIN_INVERTING false // Set to true to invert the custom pin
#if ENABLED(SKR12Pro)
#define CALIBRATION_PIN Z_MAX
#else
#define CALIBRATION_PIN 58 // Override in pins.h or set to -1 to use your Z endstop
#endif
#define CALIBRATION_PIN_INVERTING true // Set to true to invert the pin
//#define CALIBRATION_PIN_PULLDOWN
#define CALIBRATION_PIN_PULLUP
#endif
@@ -1529,7 +1556,7 @@
#endif
// Include a page of printer information in the LCD Main Menu
//#define LCD_INFO_MENU
#define LCD_INFO_MENU
#if ENABLED(LCD_INFO_MENU)
//#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages
#endif
@@ -1656,7 +1683,7 @@
#endif
// Add 'M73' to set print job progress, overrides Marlin's built-in estimate
//#define SET_PROGRESS_MANUALLY
#define SET_PROGRESS_MANUALLY
#if ENABLED(SET_PROGRESS_MANUALLY)
#define SET_PROGRESS_PERCENT // Add 'P' parameter to set percentage done
#define SET_REMAINING_TIME // Add 'R' parameter to set remaining time
@@ -1813,13 +1840,13 @@
// Allow international symbols in long filenames. To display correctly, the
// LCD's font must contain the characters. Check your selected LCD language.
//#define UTF_FILENAME_SUPPORT
#define UTF_FILENAME_SUPPORT
//#define LONG_FILENAME_HOST_SUPPORT // Get the long filename of a file/folder with 'M33 <dosname>' and list long filenames with 'M20 L'
#define LONG_FILENAME_HOST_SUPPORT // Get the long filename of a file/folder with 'M33 <dosname>' and list long filenames with 'M20 L'
//#define LONG_FILENAME_WRITE_SUPPORT // Create / delete files with long filenames via M28, M30, and Binary Transfer Protocol
//#define M20_TIMESTAMP_SUPPORT // Include timestamps by adding the 'T' flag to M20 commands
//#define SCROLL_LONG_FILENAMES // Scroll long filenames in the SD card menu
#define SCROLL_LONG_FILENAMES // Scroll long filenames in the SD card menu
//#define SD_ABORT_NO_COOLDOWN // Leave the heaters on after Stop Print (not recommended!)
@@ -1920,7 +1947,9 @@
*
* :[ 'LCD', 'ONBOARD', 'CUSTOM_CABLE' ]
*/
//#define SDCARD_CONNECTION LCD
#if ENABLED(SKR12Pro)
#define SDCARD_CONNECTION ONBOARD
#endif
// Enable if SD detect is rendered useless (e.g., by using an SD extender)
//#define NO_SD_DETECT
@@ -2266,18 +2295,18 @@
*
* Warning: Does not respect endstops!
*/
//#define BABYSTEPPING
#define BABYSTEPPING
#if ENABLED(BABYSTEPPING)
//#define EP_BABYSTEPPING // M293/M294 babystepping with EMERGENCY_PARSER support
//#define BABYSTEP_WITHOUT_HOMING
//#define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement)
#define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement)
//#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA!
//#define BABYSTEP_INVERT_Z // Enable if Z babysteps should go the other way
//#define BABYSTEP_MILLIMETER_UNITS // Specify BABYSTEP_MULTIPLICATOR_(XY|Z) in mm instead of micro-steps
#define BABYSTEP_MULTIPLICATOR_Z 1 // (steps or mm) Steps or millimeter distance for each Z babystep
#define BABYSTEP_MULTIPLICATOR_Z 20 // (steps or mm) Steps or millimeter distance for each Z babystep
#define BABYSTEP_MULTIPLICATOR_XY 1 // (steps or mm) Steps or millimeter distance for each XY babystep
//#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
#if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING)
#define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
// Note: Extra time may be added to mitigate controller latency.
@@ -2289,10 +2318,10 @@
//#define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28
//#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping
#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping
#if ENABLED(BABYSTEP_ZPROBE_OFFSET)
//#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
//#define BABYSTEP_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
#define BABYSTEP_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
#endif
#endif
@@ -2313,12 +2342,12 @@
*
* See https://marlinfw.org/docs/features/lin_advance.html for full instructions.
*/
//#define LIN_ADVANCE
#define LIN_ADVANCE
#if ENABLED(LIN_ADVANCE)
#if ENABLED(DISTINCT_E_FACTORS)
#define ADVANCE_K { 0.22 } // (mm) Compression length per 1mm/s extruder speed, per extruder
#define ADVANCE_K { 0.0 } // (mm) Compression length per 1mm/s extruder speed, per extruder
#else
#define ADVANCE_K 0.22 // (mm) Compression length applying to all extruders
#define ADVANCE_K 0.0 // (mm) Compression length applying to all extruders
#endif
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
@@ -2388,10 +2417,10 @@
#if ANY(MESH_BED_LEVELING, AUTO_BED_LEVELING_UBL)
// Override the mesh area if the automatic (max) area is too large
//#define MESH_MIN_X MESH_INSET
//#define MESH_MIN_Y MESH_INSET
//#define MESH_MAX_X X_BED_SIZE - (MESH_INSET)
//#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
#define MESH_MIN_X X_MIN_POS + MESH_INSET
#define MESH_MIN_Y Y_MIN_POS + MESH_INSET
#define MESH_MAX_X X_MAX_POS - MESH_INSET
#define MESH_MAX_Y Y_MAX_POS - MESH_INSET
#endif
#if ALL(AUTO_BED_LEVELING_UBL, EEPROM_SETTINGS)
@@ -2600,14 +2629,18 @@
#elif HAS_MEDIA
#define BLOCK_BUFFER_SIZE 16
#else
#define BLOCK_BUFFER_SIZE 16
#define BLOCK_BUFFER_SIZE 16 // maximize block buffer
#endif
// @section serial
// The ASCII buffer for serial input
#define MAX_CMD_SIZE 96
#define BUFSIZE 4
#if ENABLED(SKR12Pro)
#define BUFSIZE 16
#else
#define BUFSIZE 4
#endif
// Transmission to Host Buffer Size
// To save 386 bytes of flash (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0.
@@ -2654,7 +2687,7 @@
* Currently handles M108, M112, M410, M876
* NOTE: Not yet implemented for all platforms.
*/
//#define EMERGENCY_PARSER
#define EMERGENCY_PARSER
/**
* Realtime Reporting (requires EMERGENCY_PARSER)
@@ -2685,7 +2718,7 @@
//#define NO_TIMEOUTS 1000 // (ms)
// Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary.
//#define ADVANCED_OK
#define ADVANCED_OK
// Printrun may have trouble receiving long strings all at once.
// This option inserts short delays between lines of serial output.
@@ -2739,7 +2772,9 @@
*
* Note that M207 / M208 / M209 settings are saved to EEPROM.
*/
//#define FWRETRACT
#if ANY(ABL_Bilinear, SKR12Pro)
#define FWRETRACT
#endif
#if ENABLED(FWRETRACT)
#define FWRETRACT_AUTORETRACT // Override slicer retractions
#if ENABLED(FWRETRACT_AUTORETRACT)
@@ -2769,9 +2804,9 @@
// Z raise distance for tool-change, as needed for some extruders
#define TOOLCHANGE_ZRAISE 2 // (mm)
//#define TOOLCHANGE_ZRAISE_BEFORE_RETRACT // Apply raise before swap retraction (if enabled)
//#define TOOLCHANGE_NO_RETURN // Never return to previous position on tool-change
#define TOOLCHANGE_NO_RETURN // Never return to previous position on tool-change
#if ENABLED(TOOLCHANGE_NO_RETURN)
//#define EVENT_GCODE_AFTER_TOOLCHANGE "G12X" // Extra G-code to run after tool-change
#define EVENT_GCODE_AFTER_TOOLCHANGE "G12X" // Extra G-code to run after tool-change
#endif
/**
@@ -2800,11 +2835,11 @@
* Retract and prime filament on tool-change to reduce
* ooze and stringing and to get cleaner transitions.
*/
//#define TOOLCHANGE_FILAMENT_SWAP
#define TOOLCHANGE_FILAMENT_SWAP
#if ENABLED(TOOLCHANGE_FILAMENT_SWAP)
// Load / Unload
#define TOOLCHANGE_FS_LENGTH 12 // (mm) Load / Unload length
#define TOOLCHANGE_FS_EXTRA_RESUME_LENGTH 0 // (mm) Extra length for better restart. Adjust with LCD or M217 B.
#define TOOLCHANGE_FS_LENGTH 4 // (mm) Load / Unload length
#define TOOLCHANGE_FS_EXTRA_RESUME_LENGTH 2 // (mm) Extra length for better restart. Adjust with LCD or M217 B.
#define TOOLCHANGE_FS_RETRACT_SPEED (50*60) // (mm/min) (Unloading)
#define TOOLCHANGE_FS_UNRETRACT_SPEED (25*60) // (mm/min) (On SINGLENOZZLE or Bowden loading must be slowed down)
@@ -2887,51 +2922,51 @@
*
* Enable PARK_HEAD_ON_PAUSE to add the G-code M125 Pause and Park.
*/
//#define ADVANCED_PAUSE_FEATURE
#define ADVANCED_PAUSE_FEATURE
#if ENABLED(ADVANCED_PAUSE_FEATURE)
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
#define PAUSE_PARK_RETRACT_LENGTH 4 // (mm) Initial retract.
// This short retract is done immediately, before parking the nozzle.
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 41 // (mm/s) Unload filament feedrate. This can be pretty fast.
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
#define FILAMENT_CHANGE_UNLOAD_LENGTH 70 // (mm) The length of filament for a complete unload.
// For Bowden, the full length of the tube and nozzle.
// For direct drive, the full length of the nozzle.
// Set to 0 for manual unloading.
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
// 0 to disable start loading and skip to fast load only
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 30 // (mm/s) Load filament feedrate. This can be pretty fast.
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 50 // (mm) Load length of filament, from extruder gear to nozzle.
// For Bowden, the full length of the tube and nozzle.
// For direct drive, the full length of the nozzle.
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
#define ADVANCED_PAUSE_PURGE_LENGTH 20 // (mm) Length to extrude after loading.
// Set to 0 for manual extrusion.
// Filament can be extruded repeatedly from the Filament Change menu
// until extrusion is consistent, and to purge old filament.
#define ADVANCED_PAUSE_RESUME_PRIME 0 // (mm) Extra distance to prime nozzle after returning from park.
//#define ADVANCED_PAUSE_FANS_PAUSE // Turn off print-cooling fans while the machine is paused.
#define ADVANCED_PAUSE_RESUME_PRIME 2 // (mm) Extra distance to prime nozzle after returning from park.
#define ADVANCED_PAUSE_FANS_PAUSE // Turn off print-cooling fans while the machine is paused.
// Filament Unload does a Retract, Delay, and Purge first:
#define FILAMENT_UNLOAD_PURGE_RETRACT 13 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_PURGE_DELAY 5000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_RETRACT 4 // (mm) Unload initial retract length.
#define FILAMENT_UNLOAD_PURGE_DELAY 2000 // (ms) Delay for the filament to cool after retract.
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
#define FILAMENT_UNLOAD_PURGE_FEEDRATE 25 // (mm/s) feedrate to purge before unload
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
#define FILAMENT_CHANGE_ALERT_BEEPS 1 // Number of alert beeps to play when a response is needed.
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
//#define FILAMENT_CHANGE_RESUME_ON_INSERT // Automatically continue / load filament when runout sensor is triggered again.
//#define PAUSE_REHEAT_FAST_RESUME // Reduce number of waits by not prompting again post-timeout before continuing.
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
//#define HOME_BEFORE_FILAMENT_CHANGE // If needed, home before parking for filament change
#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
#define HOME_BEFORE_FILAMENT_CHANGE // If needed, home before parking for filament change
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
#define CONFIGURE_FILAMENT_CHANGE // Add M603 G-code and menu items. Requires ~1.3K bytes of flash.
#endif
@@ -3300,7 +3335,7 @@
* Define your own with:
* { <off_time[1..15]>, <hysteresis_end[-3..12]>, hysteresis_start[1..8] }
*/
#define CHOPPER_TIMING CHOPPER_DEFAULT_12V // All axes (override below)
#define CHOPPER_TIMING CHOPPER_DEFAULT_24V // All axes (override below)
//#define CHOPPER_TIMING_X CHOPPER_TIMING // For X Axes (override below)
//#define CHOPPER_TIMING_X2 CHOPPER_TIMING_X
//#define CHOPPER_TIMING_Y CHOPPER_TIMING // For Y Axes (override below)
@@ -3337,7 +3372,7 @@
* M912 - Clear stepper driver overtemperature pre-warn condition flag.
* M122 - Report driver parameters (Requires TMC_DEBUG)
*/
//#define MONITOR_DRIVER_STATUS
#define MONITOR_DRIVER_STATUS
#if ENABLED(MONITOR_DRIVER_STATUS)
#define CURRENT_STEP_DOWN 50 // [mA]
@@ -3354,7 +3389,7 @@
* STEALTHCHOP_(XY|Z|E) must be enabled to use HYBRID_THRESHOLD.
* M913 X/Y/Z/E to live tune the setting
*/
//#define HYBRID_THRESHOLD
#define HYBRID_THRESHOLD
#define X_HYBRID_THRESHOLD 100 // [mm/s]
#define X2_HYBRID_THRESHOLD 100
@@ -3444,7 +3479,7 @@
/**
* Step on both rising and falling edge signals (as with a square wave).
*/
//#define EDGE_STEPPING
#define EDGE_STEPPING
/**
* Enable M122 debugging command for TMC stepper drivers.
@@ -3572,7 +3607,10 @@
#if ANY(SPINDLE_FEATURE, LASER_FEATURE)
#define SPINDLE_LASER_ACTIVE_STATE LOW // Set to "HIGH" if SPINDLE_LASER_ENA_PIN is active HIGH
#define SPINDLE_LASER_USE_PWM // Enable if your controller supports setting the speed/power
#if ENABLED(SKR12Pro)
#define SPINDLE_LASER_ENA_PIN PE4
#endif
//#define SPINDLE_LASER_USE_PWM // Enable if your controller supports setting the speed/power
#if ENABLED(SPINDLE_LASER_USE_PWM)
#define SPINDLE_LASER_PWM_INVERT false // Set to "true" if the speed/power goes up when you want it to go slower
#define SPINDLE_LASER_FREQUENCY 2500 // (Hz) Spindle/laser frequency (only on supported HALs: AVR, ESP32, and LPC)
@@ -3623,8 +3661,8 @@
#define SPINDLE_CHANGE_DIR_STOP // Enable if the spindle should stop before changing spin direction
#define SPINDLE_INVERT_DIR false // Set to "true" if the spin direction is reversed
#define SPINDLE_LASER_POWERUP_DELAY 5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
#define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
#define SPINDLE_LASER_POWERUP_DELAY 1 // (ms) Delay to allow the spindle/laser to come up to speed/power
#define SPINDLE_LASER_POWERDOWN_DELAY 1 // (ms) Delay to allow the spindle to stop
/**
* M3/M4 Power Equation
@@ -4003,33 +4041,41 @@
// @section custom main menu
// Custom Menu: Main Menu
//#define CUSTOM_MENU_MAIN
#define CUSTOM_MENU_MAIN
#if ENABLED(CUSTOM_MENU_MAIN)
//#define CUSTOM_MENU_MAIN_TITLE "Custom Commands"
#define CUSTOM_MENU_MAIN_SCRIPT_DONE "M117 User Script Done"
//#define CUSTOM_MENU_MAIN_SCRIPT_DONE "M117 User Script Done"
#define CUSTOM_MENU_MAIN_TITLE "Setup"
#define CUSTOM_MENU_MAIN_SCRIPT_AUDIBLE_FEEDBACK
//#define CUSTOM_MENU_MAIN_SCRIPT_RETURN // Return to status screen after a script
#define CUSTOM_MENU_MAIN_SCRIPT_RETURN // Return to status screen after a script
#define CUSTOM_MENU_MAIN_ONLY_IDLE // Only show custom menu when the machine is idle
#define MAIN_MENU_ITEM_1_DESC "Home & UBL Info"
#define MAIN_MENU_ITEM_1_GCODE "G28\nG29 W"
//#define MAIN_MENU_ITEM_1_CONFIRM // Show a confirmation dialog before this action
#if ENABLED(TREX3)
#define COMMFANNSPEED " "
#else
#define COMMFANNSPEED "M106 S128 \n"
#endif
#define MAIN_MENU_ITEM_2_DESC "Preheat for " PREHEAT_1_LABEL
#define MAIN_MENU_ITEM_2_GCODE "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND)
//#define MAIN_MENU_ITEM_2_CONFIRM
#define MAIN_MENU_ITEM_1_DESC "Mesh Setup"
#define MAIN_MENU_ITEM_1_CONFIRM
#define MAIN_MENU_ITEM_3_DESC "Prep for Z Adjust"
#if ENABLED(ABL_Bilinear)
#define MAIN_MENU_ITEM_1_GCODE "M502 \n M500 \n M501 \n M190 S75 \n G28 \n G29 \n M500 \n G28 \n M420 S1 \n " COMMFANNSPEED " M109 S225 \n G1 X100 Y 100 \n G1 Z0 \n M77 \n M117 Set Z Offset"
#define MAIN_MENU_ITEM_3_GCODE "M190 S75 \n " COMMFANNSPEED " M104 235 \n G28 \n M420 S1 \n G1 X100 Y 100 \n G1 Z0"
#else
#define MAIN_MENU_ITEM_1_GCODE "M502 \n M500 \n M501 \n M190 S75 \n G28 \n G29 P1 \n G29 S1 \n G29 S0 \n G29 F 10.0 \n G29 A \n M500 \n G28 \n G29 L1 \n " COMMFANNSPEED " M109 S225 \n G1 X150 Y 150 \n G1 Z0 \n M77 \n M117 Set Z Offset"
#define MAIN_MENU_ITEM_3_GCODE "M190 S75 \n " COMMFANNSPEED " M104 235 \n G28 \n G29 L1 \n G1 X100 Y 100 \n G1 Z0"
#endif
//#define MAIN_MENU_ITEM_3_DESC "Preheat for " PREHEAT_2_LABEL
//#define MAIN_MENU_ITEM_3_GCODE "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND)
//#define MAIN_MENU_ITEM_3_CONFIRM
#define MAIN_MENU_ITEM_4_DESC "Fill Mesh Points"
#define MAIN_MENU_ITEM_4_GCODE "G29 P3 \n G29 P3 \n G29 P3 \n G29 T"
//#define MAIN_MENU_ITEM_4_DESC "Heat Bed/Home/Level"
//#define MAIN_MENU_ITEM_4_GCODE "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29"
//#define MAIN_MENU_ITEM_4_CONFIRM
#define MAIN_MENU_ITEM_2_DESC "PID Bed"
#define MAIN_MENU_ITEM_2_GCODE "M303 C4 S75 E-1 U \n M500 \n M117 PID Tune Done"
#define MAIN_MENU_ITEM_2_CONFIRM
//#define MAIN_MENU_ITEM_5_DESC "Home & Info"
//#define MAIN_MENU_ITEM_5_GCODE "G28\nM503"
//#define MAIN_MENU_ITEM_5_CONFIRM
#define MAIN_MENU_ITEM_5_DESC "Run Mesh Validation"
#define MAIN_MENU_ITEM_5_GCODE "G26"
#define MAIN_MENU_ITEM_5_CONFIRM
#endif
// @section custom config menu
@@ -4079,22 +4125,6 @@
#define BUTTON1_GCODE "G28"
#define BUTTON1_DESC "Homing" // Optional string to set the LCD status
#endif
//#define BUTTON2_PIN -1
#if PIN_EXISTS(BUTTON2)
#define BUTTON2_HIT_STATE LOW
#define BUTTON2_WHEN_PRINTING false
#define BUTTON2_GCODE "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND)
#define BUTTON2_DESC "Preheat for " PREHEAT_1_LABEL
#endif
//#define BUTTON3_PIN -1
#if PIN_EXISTS(BUTTON3)
#define BUTTON3_HIT_STATE LOW
#define BUTTON3_WHEN_PRINTING false
#define BUTTON3_GCODE "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND)
#define BUTTON3_DESC "Preheat for " PREHEAT_2_LABEL
#endif
#endif
// @section host
@@ -4113,14 +4143,14 @@
* Host Prompt Support enables Marlin to use the host for user prompts so
* filament runout and other processes can be managed from the host side.
*/
//#define HOST_ACTION_COMMANDS
#define HOST_ACTION_COMMANDS
#if ENABLED(HOST_ACTION_COMMANDS)
//#define HOST_PAUSE_M76 // Tell the host to pause in response to M76
//#define HOST_PROMPT_SUPPORT // Initiate host prompts to get user feedback
#define HOST_PROMPT_SUPPORT // Initiate host prompts to get user feedback
#if ENABLED(HOST_PROMPT_SUPPORT)
//#define HOST_STATUS_NOTIFICATIONS // Send some status messages to the host as notifications
#define HOST_STATUS_NOTIFICATIONS // Send some status messages to the host as notifications
#endif
//#define HOST_START_MENU_ITEM // Add a menu item that tells the host to start
#define HOST_START_MENU_ITEM // Add a menu item that tells the host to start
//#define HOST_SHUTDOWN_MENU_ITEM // Add a menu item that tells the host to shut down
#endif
Marlin/_Bootscreen.h
+93
View File
@@ -0,0 +1,93 @@
/**
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* Custom Bitmap for splashscreen
*
* You may use one of the following tools to generate the C++ bitmap array from
* a black and white image:
*
* - http://www.marlinfw.org/tools/u8glib/converter.html
* - http://www.digole.com/tools/PicturetoC_Hex_converter.php
*/
#define CUSTOM_BOOTSCREEN_TIMEOUT 2500
#define CUSTOM_BOOTSCREEN_BMPWIDTH 128
#define CUSTOM_BOOTSCREEN_INVERTED
const unsigned char custom_start_bmp[] PROGMEM = {
B11111101,B01010101,B01010101,B01010101,B01010101,B01010101,B01011111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,
B11111110,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,
B11111101,B00000000,B00000000,B00000111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,
B11111110,B00000111,B11000000,B00000101,B01010101,B01010101,B01010101,B01010101,B01010101,B01011111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,
B11111100,B00001010,B00100000,B00000110,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,
B11111110,B00010100,B00010000,B00000101,B00000000,B00000000,B00000111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,
B11111100,B00101000,B00001000,B00000110,B00000111,B11000000,B00000101,B01010101,B01010101,B01010101,B01010101,B01010101,B01011111,B11111111,B11111111,B11111111,
B11111110,B01010100,B00000100,B00000100,B00001010,B00100000,B00000110,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11111111,B11111111,B11111111,
B11111100,B01100000,B00000100,B00000110,B00010100,B00010000,B00000101,B00000000,B00000000,B00000111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,
B11111110,B01010000,B00000100,B00000100,B00101000,B00001000,B00000110,B00000111,B11000000,B00000101,B01010101,B01010101,B01010101,B01010101,B01010101,B01011111,
B11111100,B01100000,B00000100,B00000110,B01010100,B00000100,B00000100,B00001010,B00100000,B00000110,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,
B11111110,B01010100,B00000100,B00011100,B01100000,B00000100,B00000110,B00010100,B00010000,B00000101,B00000000,B00000000,B00000000,B00000000,B00000000,B00011111,
B11111100,B00101000,B00001000,B00101110,B01010000,B00000100,B00000100,B00101000,B00001000,B00000110,B00000111,B11000000,B00000000,B00000001,B11110000,B00111111,
B11111110,B00010100,B00010000,B01010100,B01100000,B00000100,B00000110,B01010100,B00000100,B00000100,B00001010,B00100000,B00000000,B00000010,B00001000,B00011111,
B11111100,B00001010,B00100000,B01100110,B01010100,B00000100,B00011100,B01100000,B00000100,B00000110,B00010100,B00010000,B00000000,B00000101,B00000100,B00111111,
B11111110,B00000111,B11000000,B01010100,B00101000,B00001000,B00101110,B01010000,B00000100,B00000100,B00101000,B00001000,B00000000,B00001010,B00000010,B00011111,
B11111100,B00000000,B00000000,B00101110,B00010100,B00010000,B01010100,B01100000,B00000100,B00000110,B01010100,B00000100,B00000000,B00010101,B00000001,B00111111,
B11111110,B00000000,B00000000,B00011100,B00001010,B00100000,B01100110,B01010100,B00000100,B00011100,B01100000,B00000100,B00000000,B00011000,B00000001,B00011111,
B11111100,B00000000,B00000000,B00000110,B00000111,B11000000,B01010100,B00101000,B00001000,B00101110,B01010000,B00000100,B00000000,B00010100,B00000001,B00111111,
B11111110,B00000000,B00000000,B00000100,B00000000,B00000000,B00101110,B00010100,B00010000,B01010100,B01100000,B00000100,B00000000,B00011000,B00000001,B00011111,
B11111100,B11111111,B11111111,B11111110,B00000000,B00000000,B00011100,B00001010,B00100000,B01100110,B01010100,B00000100,B00011100,B00010101,B00000001,B00111111,
B11111110,B11010101,B01010101,B01010100,B00000000,B00000000,B00000110,B00000111,B11000000,B01010100,B00101000,B00001000,B00101010,B00001010,B00000010,B00011111,
B11111100,B10000100,B00010000,B01000110,B00000000,B00000000,B00000100,B00000000,B00000000,B00101110,B00010100,B00010000,B01010001,B00000101,B00000100,B00111111,
B11111110,B11000100,B00010000,B01000100,B11111111,B11111111,B11111110,B00000000,B00000000,B00011100,B00001010,B00100000,B01100001,B00000010,B10001000,B00011111,
B11111100,B10000100,B00010000,B01000110,B11010101,B01010101,B01010100,B00000000,B00000000,B00000110,B00000111,B11000000,B01010001,B00000001,B11110000,B00111111,
B11111110,B10000100,B00010000,B01000100,B10000100,B00010000,B01000110,B00000000,B00000000,B00000100,B00000000,B00000000,B00101010,B00000000,B00000000,B00011111,
B11111100,B11000100,B00010000,B01000110,B11000100,B00010000,B01000100,B11111111,B11111111,B11111110,B00000000,B00000000,B00011100,B00000000,B00000000,B00111111,
B11111110,B10000100,B00010000,B01000100,B10000100,B00010000,B01000110,B11010101,B01010101,B01010100,B00000000,B00000000,B00000000,B00000000,B00000000,B00011111,
B11111100,B11010101,B01010101,B01010110,B10000100,B00010000,B01000100,B10000100,B00010000,B01000110,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,
B11111100,B11111111,B11111111,B11111100,B11000100,B00010000,B01000110,B11000100,B00010000,B01000100,B11111111,B11111111,B11111111,B11111111,B11111111,B10011111,
B11111110,B00000000,B00000000,B00000110,B10000100,B00010000,B01000100,B10000100,B00010000,B01000110,B11010101,B01010101,B01010101,B01010101,B01010101,B10111111,
B11111101,B01010101,B01010101,B01010100,B11010101,B01010101,B01010110,B10000100,B00010000,B01000100,B10000100,B00010000,B01000001,B00000100,B00010000,B10011111,
B11111111,B11111111,B11111111,B11111100,B11111111,B11111111,B11111100,B11000100,B00010000,B01000110,B11000100,B00010000,B01000001,B00000100,B00010001,B10111111,
B11111111,B11111111,B11111111,B11111110,B00000000,B00000000,B00000110,B10000100,B00010000,B01000100,B10000100,B00010000,B01000001,B00000100,B00010000,B10011111,
B11111111,B11111111,B11111111,B11111101,B01010101,B01010101,B01010100,B11010101,B01010101,B01010110,B10000100,B00010000,B01000001,B00000100,B00010000,B10011111,
B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111100,B11111111,B11111111,B11111100,B11000100,B00010000,B01000001,B00000100,B00010001,B10111111,
B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111110,B00000000,B00000000,B00000110,B10000100,B00010000,B01000001,B00000100,B00010000,B10011111,
B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111101,B01010101,B01010101,B01010100,B11010101,B01010101,B01010101,B01010101,B01010101,B10111111,
B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111100,B11111111,B11111111,B11111111,B11111111,B11111111,B10011111,
B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111110,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,
B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111101,B01010101,B01010101,B01010101,B01010101,B01010101,B01011111,
B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,
B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,
B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,
B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,
B11100000,B00101110,B11111011,B01111101,B11111011,B11111011,B11001111,B11000001,B11011111,B10111011,B00111110,B11000000,B11100001,B11111110,B00111100,B00011111,
B11111101,B11101110,B01111011,B00111001,B11111001,B11110011,B11001111,B10011110,B11011111,B10111011,B00111110,B11011111,B11011110,B11111100,B11011101,B11100111,
B11111101,B11101110,B00111011,B10111011,B11111001,B11101011,B11010111,B10111111,B01011111,B10111011,B01011110,B11011111,B11011110,B11111101,B11101101,B11110111,
B11111101,B11101110,B10111011,B11010011,B11111010,B11101011,B10110111,B00111111,B11011111,B10111011,B01001110,B11011111,B11011111,B11111111,B11001101,B11110011,
B11111101,B11101110,B11011011,B11000111,B11111010,B11101011,B10111011,B01111111,B11000000,B00111011,B01101110,B11000000,B11100011,B11111111,B00011101,B11110011,
B11111101,B11101110,B11001011,B11101111,B11111010,B11011011,B10111011,B01111111,B11011111,B10111011,B01100110,B11011111,B11111000,B11111111,B11001101,B11110011,
B11111101,B11101110,B11101011,B11101111,B11111011,B01011011,B00000011,B00111111,B01011111,B10111011,B01110110,B11011111,B11111110,B01111111,B11101101,B11110011,
B11111101,B11101110,B11110011,B11101111,B11111011,B01011011,B01111001,B10111110,B11011111,B10111011,B01111010,B11011111,B11011110,B01111101,B11101101,B11110111,
B11111101,B11101110,B11110011,B11101111,B11111011,B10111010,B11111101,B10011110,B11011111,B10111011,B01111100,B11011111,B11011110,B11111101,B11001101,B11100111,
B11111101,B11101110,B11111011,B11101111,B11111011,B10111010,B11111101,B11000001,B11011111,B10111011,B01111110,B11000000,B11100000,B11111110,B00011100,B00011111
};
Marlin/_Statusscreen.h
+74
View File
@@ -0,0 +1,74 @@
/**
* Marlin 3D Printer Firmware
* Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
*
* Based on Sprinter and grbl.
* Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
*
* This program is free software: you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation, either version 3 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
/**
* Custom Status Screen bitmap
*
* Place this file in the root with your configuration files
* and enable CUSTOM_STATUS_SCREEN_IMAGE in Configuration.h.
*
* Use the Marlin Bitmap Converter to make your own:
* http://marlinfw.org/tools/u8glib/converter.html
*/
//
// Status Screen Logo bitmap
//
#define STATUS_LOGO_Y 3
#define STATUS_LOGO_WIDTH 24
const unsigned char status_logo_bmp[] PROGMEM = {
B11111111,B11111111,B11111111,
B10000000,B00000000,B00000001,
B10001110,B00000000,B11100001,
B10011111,B00000001,B11110001,
B10010011,B10000001,B00111001,
B10011111,B10000001,B11111001,
B10011111,B10000001,B11111001,
B10011111,B10111001,B11111001,
B10001111,B00101000,B11110001,
B10000000,B00111000,B00000001,
B10000000,B00000000,B00000001,
B10011111,B11111111,B11111001,
B10010001,B01110100,B10011001,
B10011011,B00000110,B10101001,
B10011011,B01010100,B10101001,
B10011011,B01010110,B10101001,
B10011011,B01010100,B10011001,
B10011111,B11111111,B11111001,
B11111111,B11111111,B11111111
};
//
// Use default bitmaps
//
#define STATUS_HOTEND_ANIM
#define STATUS_BED_ANIM
#if HOTENDS < 2
#define STATUS_LOGO_X 8
#define STATUS_HEATERS_X 40
#define STATUS_BED_X 72
#else
#define STATUS_LOGO_X 0
#define STATUS_HEATERS_X 32
#define STATUS_BED_X 80
#endif