jessikitty/Marlin
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity

Update Configuration.h

Browse Source
This commit is contained in:
InsanityAutomation
2022-03-12 15:53:28 -05:00
parent 70f7866b73
commit 384fec1c25
1 changed files with 18 additions and 23 deletions
Download Patch File Download Diff File Expand all files Collapse all files
Marlin/Configuration.h
+18 -23
View File
@@ -17,19 +17,19 @@
*/
//#define X_2208 // TMC2208 or 2209 in Standalone Mode
//#define X_SpreadCycle
//#define X_2209_Uart
#define X_2209_Uart
//#define Y_2208
//#define Y_SpreadCycle // Highly recommended as large prints with high mass can cause layer shifts with stealthchop at high speed
//#define Y_4988 // Some machines shipped with 4988 drivers across the board. Set this if you arent sure what you have and all the drivers look identical
//#define Y_2209_Uart
#define Y_2209_Uart
//#define Z_2208 // NOT Recommended! Dual stepper current draw is above the recommended limit for this driver
//#define Z_SpreadCycle
//#define Z_4988 // Some machines shipped with 4988 drivers across the board. Set this if you arent sure what you have and all the drivers look identical
//#define Z_2209_Uart
#define Z_2209_Uart
//#define E_2208 // Not Recommended! Stealthchop mode faults with linear advance
//#define E_SpreadCycle
//#define E_4988
//#define E_2209_Uart
#define E_2209_Uart
//#define SKR13
//#define SKR14
@@ -55,7 +55,7 @@
//#define HotendCreality
//#define HighPoweredHeater
//#define ExtruderDDX //DDX kit with Linear Rail
#define ExtruderDDX //DDX kit with Linear Rail
//#define ExtruderBMG
/**
@@ -774,15 +774,9 @@
#define DEFAULT_Ki_LIST { 1.08, 1.08 }
#define DEFAULT_Kd_LIST { 114.00, 114.00 }
#else
#if ENABLED(E3DHemeraExtruder)
#define DEFAULT_Kp 21.9
#define DEFAULT_Ki 1.5
#define DEFAULT_Kd 79.88
#elif ENABLED(HotendAllMetal)
#define DEFAULT_Kp 21.9
#define DEFAULT_Ki 1.5
#define DEFAULT_Kd 79.88
#endif
#define DEFAULT_Kp 21.9
#define DEFAULT_Ki 1.5
#define DEFAULT_Kd 79.88
#endif
// MakerGear
//#define DEFAULT_Kp 7.0
@@ -1031,7 +1025,7 @@
// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
#define I_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
#define J_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
#define K_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
@@ -1780,13 +1774,14 @@
#endif
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
#define FIL_RUNOUT_ENABLED_DEFAULT true // Enable the sensor on startup. Override with M412 followed by M500.
#define FIL_RUNOUT_ENABLED_DEFAULT true // Enable the sensor on startup. Override with M591 followed by M500.
#if NONE(RAPTOR2, SKRBoard)
#define FIL_RUNOUT_PIN 57
#define FIL_RUNOUT_STATE HIGH // set to true to invert the logic of the sensor.
#else
#define FIL_RUNOUT_STATE LOW // set to true to invert the logic of the sensor.
#endif
#define FILAMENT_RUNOUT_DEFAULT_MODE {1}
#define FIL_RUNOUT_PULLUP // Use internal pullup for filament runout pins.
//#define FIL_RUNOUT_PULLDOWN // Use internal pulldown for filament runout pins.
//#define WATCH_ALL_RUNOUT_SENSORS // Execute runout script on any triggering sensor, not only for the active extruder.
@@ -1827,19 +1822,19 @@
// Commands to execute on filament runout.
// With multiple runout sensors use the %c placeholder for the current tool in commands (e.g., "M600 T%c")
// NOTE: After 'M412 H1' the host handles filament runout and this script does not apply.
// NOTE: After 'M591 H1' the host handles filament runout and this script does not apply.
#define FILAMENT_RUNOUT_SCRIPT "M600"
// After a runout is detected, continue printing this length of filament
// before executing the runout script. Useful for a sensor at the end of
// a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead.
#if ENABLED(RunoutEncoder)
#define FILAMENT_RUNOUT_DISTANCE_MM 15
#else
#define FILAMENT_RUNOUT_DISTANCE_MM 5
#endif
//#if ENABLED(RunoutEncoder)
#define FILAMENT_RUNOUT_DISTANCE_MM {15}
//#else
// #define FILAMENT_RUNOUT_DISTANCE_MM {5}
//#endif
#ifdef FILAMENT_RUNOUT_DISTANCE_MM
#if defined(FILAMENT_RUNOUT_DISTANCE_MM)
// Enable this option to use an encoder disc that toggles the runout pin
// as the filament moves. (Be sure to set FILAMENT_RUNOUT_DISTANCE_MM
// large enough to avoid false positives.)