Bump for 2209

Marlin/Configuration.h

@@ -1,6 +1,6 @@
 #define ABL_BLTOUCH // Replaces RGB LED
-//#define GraphicalLCD // Will work next to MKS TFT
-//#define TMC_2208 // Defaults to TMC2100
+#define GraphicalLCD // Will work next to MKS TFT
+#define TMC_2209 // Defaults to TMC2100
 #define ABL_UBL // Defaults to Bilinear
 //#define RunoutSensor // Tinymachines Lerdge Sensor
 #define RELOCATE_LED // Since the bltouch by default removed the LED, set this if you simply moved them off the hotend
@@ -675,12 +675,12 @@
  *          TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE
  * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
  */
-#if ENABLED(TMC_2208)
-  #define X_DRIVER_TYPE  TMC2208_STANDALONE
-  #define Y_DRIVER_TYPE  TMC2208_STANDALONE
-  #define Z_DRIVER_TYPE  TMC2208_STANDALONE
-  #define Z2_DRIVER_TYPE TMC2208_STANDALONE
-  #define E0_DRIVER_TYPE TMC2208_STANDALONE
+#if ENABLED(TMC_2209)
+  #define X_DRIVER_TYPE  TMC2209
+  #define Y_DRIVER_TYPE  TMC2209
+  #define Z_DRIVER_TYPE  TMC2209
+  #define Z2_DRIVER_TYPE TMC2209
+  #define E0_DRIVER_TYPE TMC2209
 #else
   #define X_DRIVER_TYPE  TMC2100
   #define Y_DRIVER_TYPE  TMC2100
@@ -1036,20 +1036,36 @@
 // @section machine
 
 // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
-#define INVERT_X_DIR false
-#define INVERT_Y_DIR false
-#define INVERT_Z_DIR true
+#if ENABLED(TMC_2209)
+  #define INVERT_X_DIR true
+  #define INVERT_Y_DIR true
+  #define INVERT_Z_DIR false
 
-// @section extruder
+  // @section extruder
 
-// For direct drive extruder v9 set to true, for geared extruder set to false.
-#define INVERT_E0_DIR false
-#define INVERT_E1_DIR false
-#define INVERT_E2_DIR false
-#define INVERT_E3_DIR false
-#define INVERT_E4_DIR false
-#define INVERT_E5_DIR false
+  // For direct drive extruder v9 set to true, for geared extruder set to false.
+  #define INVERT_E0_DIR true
+  #define INVERT_E1_DIR true
+  #define INVERT_E2_DIR true
+  #define INVERT_E3_DIR true
+  #define INVERT_E4_DIR true
+  #define INVERT_E5_DIR true
+#else
+  #define INVERT_X_DIR false
+  #define INVERT_Y_DIR false
+  #define INVERT_Z_DIR true
 
+  // @section extruder
+
+  // For direct drive extruder v9 set to true, for geared extruder set to false.
+  #define INVERT_E0_DIR false
+  #define INVERT_E1_DIR false
+  #define INVERT_E2_DIR false
+  #define INVERT_E3_DIR false
+  #define INVERT_E4_DIR false
+  #define INVERT_E5_DIR false
+
+#endif
 // @section homing
 
 //#define NO_MOTION_BEFORE_HOMING  // Inhibit movement until all axes have been homed
@@ -2170,7 +2186,7 @@
  * LED Type. Enable only one of the following two options.
  *
  */
-#if DISABLED(ABL_BLTOUCH, RELOCATE_LED)
+#if DISABLED(ABL_BLTOUCH) || ENABLED(RELOCATE_LED)
   #define RGB_LED
 #endif
 //#define RGBW_LED

Marlin/Configuration_adv.h

@@ -1214,7 +1214,7 @@
  * See http://marlinfw.org/docs/features/lin_advance.html for full instructions.
  * Mention @Sebastianv650 on GitHub to alert the author of any issues.
  */
-#if DISABLED(TMC_2208)
+#if DISABLED(TMC_2209)
   #define LIN_ADVANCE
 #endif
 #if ENABLED(LIN_ADVANCE)
@@ -1789,7 +1789,7 @@
    */
   #define STEALTHCHOP_XY
   #define STEALTHCHOP_Z
-  #define STEALTHCHOP_E
+  //#define STEALTHCHOP_E
 
   /**
    * Optimize spreadCycle chopper parameters by using predefined parameter sets
@@ -1805,7 +1805,7 @@
    * Define you own with
    * { <off_time[1..15]>, <hysteresis_end[-3..12]>, hysteresis_start[1..8] }
    */
-  #define CHOPPER_TIMING CHOPPER_DEFAULT_12V
+  #define CHOPPER_TIMING CHOPPER_DEFAULT_24V
 
   /**
    * Monitor Trinamic drivers for error conditions,
@@ -1833,7 +1833,7 @@
    * STEALTHCHOP_(XY|Z|E) must be enabled to use HYBRID_THRESHOLD.
    * M913 X/Y/Z/E to live tune the setting
    */
-  //#define HYBRID_THRESHOLD
+  #define HYBRID_THRESHOLD
 
   #define X_HYBRID_THRESHOLD     100  // [mm/s]
   #define X2_HYBRID_THRESHOLD    100

Marlin/src/pins/ramps/pins_RAMPS.h

@@ -333,8 +333,8 @@
 
   #define Z_SERIAL_TX_PIN    42
   #define Z_SERIAL_RX_PIN    65
-  #define Z2_SERIAL_TX_PIN   -1
-  #define Z2_SERIAL_RX_PIN   -1
+  #define Z2_SERIAL_TX_PIN   2
+  #define Z2_SERIAL_RX_PIN   15
 
   #define E0_SERIAL_TX_PIN   44
   #define E0_SERIAL_RX_PIN   66