Initial Commit
This commit is contained in:
InsanityAutomation
+67
-67
@@ -69,7 +69,7 @@
|
||||
// @section info
|
||||
|
||||
// Author info of this build printed to the host during boot and M115
|
||||
#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
|
||||
#define STRING_CONFIG_H_AUTHOR "Insanity Automation" // Who made the changes.
|
||||
//#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
|
||||
|
||||
/**
|
||||
@@ -139,7 +139,7 @@
|
||||
|
||||
// Choose the name from boards.h that matches your setup
|
||||
#ifndef MOTHERBOARD
|
||||
#define MOTHERBOARD BOARD_RAMPS_14_EFB
|
||||
#define MOTHERBOARD BOARD_ORTUR_4
|
||||
#endif
|
||||
|
||||
// Name displayed in the LCD "Ready" message and Info menu
|
||||
@@ -429,7 +429,7 @@
|
||||
#define TEMP_SENSOR_5 0
|
||||
#define TEMP_SENSOR_6 0
|
||||
#define TEMP_SENSOR_7 0
|
||||
#define TEMP_SENSOR_BED 0
|
||||
#define TEMP_SENSOR_BED 1
|
||||
#define TEMP_SENSOR_PROBE 0
|
||||
#define TEMP_SENSOR_CHAMBER 0
|
||||
#define TEMP_SENSOR_COOLER 0
|
||||
@@ -449,11 +449,11 @@
|
||||
//#define TEMP_SENSOR_1_AS_REDUNDANT
|
||||
#define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
|
||||
|
||||
#define TEMP_RESIDENCY_TIME 10 // (seconds) Time to wait for hotend to "settle" in M109
|
||||
#define TEMP_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
|
||||
#define TEMP_RESIDENCY_TIME 5 // (seconds) Time to wait for hotend to "settle" in M109
|
||||
#define TEMP_WINDOW 2 // (°C) Temperature proximity for the "temperature reached" timer
|
||||
#define TEMP_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
|
||||
|
||||
#define TEMP_BED_RESIDENCY_TIME 10 // (seconds) Time to wait for bed to "settle" in M190
|
||||
#define TEMP_BED_RESIDENCY_TIME 5 // (seconds) Time to wait for bed to "settle" in M190
|
||||
#define TEMP_BED_WINDOW 1 // (°C) Temperature proximity for the "temperature reached" timer
|
||||
#define TEMP_BED_HYSTERESIS 3 // (°C) Temperature proximity considered "close enough" to the target
|
||||
|
||||
@@ -485,7 +485,7 @@
|
||||
#define HEATER_5_MAXTEMP 275
|
||||
#define HEATER_6_MAXTEMP 275
|
||||
#define HEATER_7_MAXTEMP 275
|
||||
#define BED_MAXTEMP 150
|
||||
#define BED_MAXTEMP 120
|
||||
#define CHAMBER_MAXTEMP 60
|
||||
|
||||
/**
|
||||
@@ -510,8 +510,8 @@
|
||||
#define PID_K1 0.95 // Smoothing factor within any PID loop
|
||||
|
||||
#if ENABLED(PIDTEMP)
|
||||
//#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
|
||||
//#define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
|
||||
#define PID_EDIT_MENU // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
|
||||
#define PID_AUTOTUNE_MENU // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
|
||||
//#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
|
||||
// Set/get with gcode: M301 E[extruder number, 0-2]
|
||||
|
||||
@@ -545,7 +545,7 @@
|
||||
* heater. If your configuration is significantly different than this and you don't understand
|
||||
* the issues involved, don't use bed PID until someone else verifies that your hardware works.
|
||||
*/
|
||||
//#define PIDTEMPBED
|
||||
#define PIDTEMPBED
|
||||
|
||||
//#define BED_LIMIT_SWITCHING
|
||||
|
||||
@@ -563,9 +563,9 @@
|
||||
|
||||
// 120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
|
||||
// from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
|
||||
#define DEFAULT_bedKp 10.00
|
||||
#define DEFAULT_bedKi .023
|
||||
#define DEFAULT_bedKd 305.4
|
||||
#define DEFAULT_bedKp 87.23
|
||||
#define DEFAULT_bedKi 13.31
|
||||
#define DEFAULT_bedKd 381.14
|
||||
|
||||
// FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
|
||||
#endif // PIDTEMPBED
|
||||
@@ -722,13 +722,13 @@
|
||||
#endif
|
||||
|
||||
// Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
|
||||
#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
|
||||
#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
|
||||
#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
|
||||
#define Z_MIN_PROBE_ENDSTOP_INVERTING true // Set to true to invert the logic of the probe.
|
||||
|
||||
/**
|
||||
* Stepper Drivers
|
||||
@@ -811,14 +811,14 @@
|
||||
* Override with M92
|
||||
* X, Y, Z, E0 [, E1[, E2...]]
|
||||
*/
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 500 }
|
||||
#define DEFAULT_AXIS_STEPS_PER_UNIT { 80, 80, 400, 95 }
|
||||
|
||||
/**
|
||||
* Default Max Feed Rate (mm/s)
|
||||
* Override with M203
|
||||
* X, Y, Z, E0 [, E1[, E2...]]
|
||||
*/
|
||||
#define DEFAULT_MAX_FEEDRATE { 300, 300, 5, 25 }
|
||||
#define DEFAULT_MAX_FEEDRATE { 500, 500, 10, 65 }
|
||||
|
||||
//#define LIMITED_MAX_FR_EDITING // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
|
||||
#if ENABLED(LIMITED_MAX_FR_EDITING)
|
||||
@@ -831,7 +831,7 @@
|
||||
* Override with M201
|
||||
* X, Y, Z, E0 [, E1[, E2...]]
|
||||
*/
|
||||
#define DEFAULT_MAX_ACCELERATION { 3000, 3000, 100, 10000 }
|
||||
#define DEFAULT_MAX_ACCELERATION { 2500, 2500, 18000, 8000 }
|
||||
|
||||
//#define LIMITED_MAX_ACCEL_EDITING // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
|
||||
#if ENABLED(LIMITED_MAX_ACCEL_EDITING)
|
||||
@@ -846,8 +846,8 @@
|
||||
* M204 R Retract Acceleration
|
||||
* M204 T Travel Acceleration
|
||||
*/
|
||||
#define DEFAULT_ACCELERATION 3000 // X, Y, Z and E acceleration for printing moves
|
||||
#define DEFAULT_RETRACT_ACCELERATION 3000 // E acceleration for retracts
|
||||
#define DEFAULT_ACCELERATION 2000 // X, Y, Z and E acceleration for printing moves
|
||||
#define DEFAULT_RETRACT_ACCELERATION 2000 // E acceleration for retracts
|
||||
#define DEFAULT_TRAVEL_ACCELERATION 3000 // X, Y, Z acceleration for travel (non printing) moves
|
||||
|
||||
/**
|
||||
@@ -858,10 +858,10 @@
|
||||
* When changing speed and direction, if the difference is less than the
|
||||
* value set here, it may happen instantaneously.
|
||||
*/
|
||||
//#define CLASSIC_JERK
|
||||
#define CLASSIC_JERK
|
||||
#if ENABLED(CLASSIC_JERK)
|
||||
#define DEFAULT_XJERK 10.0
|
||||
#define DEFAULT_YJERK 10.0
|
||||
#define DEFAULT_XJERK 15.0
|
||||
#define DEFAULT_YJERK 15.0
|
||||
#define DEFAULT_ZJERK 0.3
|
||||
|
||||
//#define TRAVEL_EXTRA_XYJERK 0.0 // Additional jerk allowance for all travel moves
|
||||
@@ -895,7 +895,7 @@
|
||||
*
|
||||
* See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained
|
||||
*/
|
||||
//#define S_CURVE_ACCELERATION
|
||||
#define S_CURVE_ACCELERATION
|
||||
|
||||
//===========================================================================
|
||||
//============================= Z Probe Options =============================
|
||||
@@ -911,7 +911,7 @@
|
||||
* The probe replaces the Z-MIN endstop and is used for Z homing.
|
||||
* (Automatically enables USE_PROBE_FOR_Z_HOMING.)
|
||||
*/
|
||||
#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
//#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
|
||||
|
||||
// Force the use of the probe for Z-axis homing
|
||||
//#define USE_PROBE_FOR_Z_HOMING
|
||||
@@ -951,7 +951,7 @@
|
||||
* A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
|
||||
* (e.g., an inductive probe or a nozzle-based probe-switch.)
|
||||
*/
|
||||
//#define FIX_MOUNTED_PROBE
|
||||
#define FIX_MOUNTED_PROBE
|
||||
|
||||
/**
|
||||
* Use the nozzle as the probe, as with a conductive
|
||||
@@ -1060,17 +1060,17 @@
|
||||
* | [-] |
|
||||
* O-- FRONT --+
|
||||
*/
|
||||
#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
|
||||
#define NOZZLE_TO_PROBE_OFFSET { -25, 0, 0 }
|
||||
|
||||
// Most probes should stay away from the edges of the bed, but
|
||||
// with NOZZLE_AS_PROBE this can be negative for a wider probing area.
|
||||
#define PROBING_MARGIN 10
|
||||
#define PROBING_MARGIN 8
|
||||
|
||||
// X and Y axis travel speed (mm/min) between probes
|
||||
#define XY_PROBE_FEEDRATE (133*60)
|
||||
|
||||
// Feedrate (mm/min) for the first approach when double-probing (MULTIPLE_PROBING == 2)
|
||||
#define Z_PROBE_FEEDRATE_FAST (4*60)
|
||||
#define Z_PROBE_FEEDRATE_FAST (10*60)
|
||||
|
||||
// Feedrate (mm/min) for the "accurate" probe of each point
|
||||
#define Z_PROBE_FEEDRATE_SLOW (Z_PROBE_FEEDRATE_FAST / 2)
|
||||
@@ -1111,7 +1111,7 @@
|
||||
* A total of 2 does fast/slow probes with a weighted average.
|
||||
* A total of 3 or more adds more slow probes, taking the average.
|
||||
*/
|
||||
//#define MULTIPLE_PROBING 2
|
||||
#define MULTIPLE_PROBING 2
|
||||
//#define EXTRA_PROBING 1
|
||||
|
||||
/**
|
||||
@@ -1128,16 +1128,16 @@
|
||||
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
|
||||
*/
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 5 // Z Clearance for Deploy/Stow
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
|
||||
#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes
|
||||
//#define Z_AFTER_PROBING 5 // Z position after probing is done
|
||||
|
||||
#define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping
|
||||
#define Z_PROBE_LOW_POINT -4 // Farthest distance below the trigger-point to go before stopping
|
||||
|
||||
// For M851 give a range for adjusting the Z probe offset
|
||||
#define Z_PROBE_OFFSET_RANGE_MIN -20
|
||||
#define Z_PROBE_OFFSET_RANGE_MAX 20
|
||||
#define Z_PROBE_OFFSET_RANGE_MIN -9
|
||||
#define Z_PROBE_OFFSET_RANGE_MAX 9
|
||||
|
||||
// Enable the M48 repeatability test to test probe accuracy
|
||||
//#define Z_MIN_PROBE_REPEATABILITY_TEST
|
||||
@@ -1197,12 +1197,12 @@
|
||||
// Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
|
||||
#define INVERT_X_DIR false
|
||||
#define INVERT_Y_DIR true
|
||||
#define INVERT_Z_DIR false
|
||||
#define INVERT_Z_DIR true
|
||||
|
||||
// @section extruder
|
||||
|
||||
// For direct drive extruder v9 set to true, for geared extruder set to false.
|
||||
#define INVERT_E0_DIR false
|
||||
#define INVERT_E0_DIR true
|
||||
#define INVERT_E1_DIR false
|
||||
#define INVERT_E2_DIR false
|
||||
#define INVERT_E3_DIR false
|
||||
@@ -1237,16 +1237,16 @@
|
||||
// @section machine
|
||||
|
||||
// The size of the printable area
|
||||
#define X_BED_SIZE 200
|
||||
#define Y_BED_SIZE 200
|
||||
#define X_BED_SIZE 255
|
||||
#define Y_BED_SIZE 300
|
||||
|
||||
// Travel limits (mm) after homing, corresponding to endstop positions.
|
||||
#define X_MIN_POS 0
|
||||
#define Y_MIN_POS 0
|
||||
#define X_MIN_POS -10.5
|
||||
#define Y_MIN_POS -9
|
||||
#define Z_MIN_POS 0
|
||||
#define X_MAX_POS X_BED_SIZE
|
||||
#define Y_MAX_POS Y_BED_SIZE
|
||||
#define Z_MAX_POS 200
|
||||
#define X_MAX_POS 260
|
||||
#define Y_MAX_POS 310
|
||||
#define Z_MAX_POS 295
|
||||
|
||||
/**
|
||||
* Software Endstops
|
||||
@@ -1274,7 +1274,7 @@
|
||||
#endif
|
||||
|
||||
#if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS)
|
||||
//#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD
|
||||
#define SOFT_ENDSTOPS_MENU_ITEM // Enable/Disable software endstops from the LCD
|
||||
#endif
|
||||
|
||||
/**
|
||||
@@ -1290,7 +1290,7 @@
|
||||
* RAMPS-based boards use SERVO3_PIN for the first runout sensor.
|
||||
* For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
|
||||
*/
|
||||
//#define FILAMENT_RUNOUT_SENSOR
|
||||
#define FILAMENT_RUNOUT_SENSOR
|
||||
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
|
||||
#define FIL_RUNOUT_ENABLED_DEFAULT true // Enable the sensor on startup. Override with M412 followed by M500.
|
||||
#define NUM_RUNOUT_SENSORS 1 // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
|
||||
@@ -1342,7 +1342,7 @@
|
||||
// After a runout is detected, continue printing this length of filament
|
||||
// before executing the runout script. Useful for a sensor at the end of
|
||||
// a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead.
|
||||
//#define FILAMENT_RUNOUT_DISTANCE_MM 25
|
||||
#define FILAMENT_RUNOUT_DISTANCE_MM 5
|
||||
|
||||
#ifdef FILAMENT_RUNOUT_DISTANCE_MM
|
||||
// Enable this option to use an encoder disc that toggles the runout pin
|
||||
@@ -1392,7 +1392,7 @@
|
||||
*/
|
||||
//#define AUTO_BED_LEVELING_3POINT
|
||||
//#define AUTO_BED_LEVELING_LINEAR
|
||||
//#define AUTO_BED_LEVELING_BILINEAR
|
||||
#define AUTO_BED_LEVELING_BILINEAR
|
||||
//#define AUTO_BED_LEVELING_UBL
|
||||
//#define MESH_BED_LEVELING
|
||||
|
||||
@@ -1401,13 +1401,13 @@
|
||||
* these options to restore the prior leveling state or to always enable
|
||||
* leveling immediately after G28.
|
||||
*/
|
||||
//#define RESTORE_LEVELING_AFTER_G28
|
||||
#define RESTORE_LEVELING_AFTER_G28
|
||||
//#define ENABLE_LEVELING_AFTER_G28
|
||||
|
||||
/**
|
||||
* Auto-leveling needs preheating
|
||||
*/
|
||||
//#define PREHEAT_BEFORE_LEVELING
|
||||
#define PREHEAT_BEFORE_LEVELING
|
||||
#if ENABLED(PREHEAT_BEFORE_LEVELING)
|
||||
#define LEVELING_NOZZLE_TEMP 120 // (°C) Only applies to E0 at this time
|
||||
#define LEVELING_BED_TEMP 50
|
||||
@@ -1431,7 +1431,7 @@
|
||||
// The height can be set with M420 Z<height>
|
||||
#define ENABLE_LEVELING_FADE_HEIGHT
|
||||
#if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)
|
||||
#define DEFAULT_LEVELING_FADE_HEIGHT 10.0 // (mm) Default fade height.
|
||||
#define DEFAULT_LEVELING_FADE_HEIGHT 0.0 // (mm) Default fade height.
|
||||
#endif
|
||||
|
||||
// For Cartesian machines, instead of dividing moves on mesh boundaries,
|
||||
@@ -1459,7 +1459,7 @@
|
||||
#if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR)
|
||||
|
||||
// Set the number of grid points per dimension.
|
||||
#define GRID_MAX_POINTS_X 3
|
||||
#define GRID_MAX_POINTS_X 5
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
// Probe along the Y axis, advancing X after each column
|
||||
@@ -1523,27 +1523,27 @@
|
||||
* Add a bed leveling sub-menu for ABL or MBL.
|
||||
* Include a guided procedure if manual probing is enabled.
|
||||
*/
|
||||
//#define LCD_BED_LEVELING
|
||||
#define LCD_BED_LEVELING
|
||||
|
||||
#if ENABLED(LCD_BED_LEVELING)
|
||||
#define MESH_EDIT_Z_STEP 0.025 // (mm) Step size while manually probing Z axis.
|
||||
#define LCD_PROBE_Z_RANGE 4 // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment
|
||||
//#define MESH_EDIT_MENU // Add a menu to edit mesh points
|
||||
#define MESH_EDIT_MENU // Add a menu to edit mesh points
|
||||
#endif
|
||||
|
||||
// Add a menu item to move between bed corners for manual bed adjustment
|
||||
//#define LEVEL_BED_CORNERS
|
||||
#define LEVEL_BED_CORNERS
|
||||
|
||||
#if ENABLED(LEVEL_BED_CORNERS)
|
||||
#define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets
|
||||
#define LEVEL_CORNERS_HEIGHT 0.0 // (mm) Z height of nozzle at leveling points
|
||||
#define LEVEL_CORNERS_Z_HOP 4.0 // (mm) Z height of nozzle between leveling points
|
||||
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
|
||||
//#define LEVEL_CORNERS_USE_PROBE
|
||||
#define LEVEL_CORNERS_USE_PROBE
|
||||
#if ENABLED(LEVEL_CORNERS_USE_PROBE)
|
||||
#define LEVEL_CORNERS_PROBE_TOLERANCE 0.1
|
||||
#define LEVEL_CORNERS_VERIFY_RAISED // After adjustment triggers the probe, re-probe to verify
|
||||
//#define LEVEL_CORNERS_AUDIO_FEEDBACK
|
||||
#define LEVEL_CORNERS_AUDIO_FEEDBACK
|
||||
#endif
|
||||
|
||||
/**
|
||||
@@ -1677,12 +1677,12 @@
|
||||
* M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
|
||||
* M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
|
||||
*/
|
||||
//#define EEPROM_SETTINGS // Persistent storage with M500 and M501
|
||||
#define EEPROM_SETTINGS // Persistent storage with M500 and M501
|
||||
//#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release!
|
||||
#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM.
|
||||
#define EEPROM_BOOT_SILENT // Keep M503 quiet and only give errors during first load
|
||||
#if ENABLED(EEPROM_SETTINGS)
|
||||
//#define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors.
|
||||
#define EEPROM_AUTO_INIT // Init EEPROM automatically on any errors.
|
||||
#endif
|
||||
|
||||
//
|
||||
@@ -1733,11 +1733,11 @@
|
||||
* P1 Raise the nozzle always to Z-park height.
|
||||
* P2 Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
|
||||
*/
|
||||
//#define NOZZLE_PARK_FEATURE
|
||||
#define NOZZLE_PARK_FEATURE
|
||||
|
||||
#if ENABLED(NOZZLE_PARK_FEATURE)
|
||||
// Specify a park position as { X, Y, Z_raise }
|
||||
#define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
|
||||
#define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MIN_POS + 10), 5 }
|
||||
//#define NOZZLE_PARK_X_ONLY // X move only is required to park
|
||||
//#define NOZZLE_PARK_Y_ONLY // Y move only is required to park
|
||||
#define NOZZLE_PARK_Z_RAISE_MIN 2 // (mm) Always raise Z by at least this distance
|
||||
@@ -1941,7 +1941,7 @@
|
||||
* SD Card support is disabled by default. If your controller has an SD slot,
|
||||
* you must uncomment the following option or it won't work.
|
||||
*/
|
||||
//#define SDSUPPORT
|
||||
#define SDSUPPORT
|
||||
|
||||
/**
|
||||
* SD CARD: ENABLE CRC
|
||||
@@ -1988,7 +1988,7 @@
|
||||
//
|
||||
// Set this option if CLOCKWISE causes values to DECREASE
|
||||
//
|
||||
//#define REVERSE_ENCODER_DIRECTION
|
||||
#define REVERSE_ENCODER_DIRECTION
|
||||
|
||||
//
|
||||
// This option reverses the encoder direction for navigating LCD menus.
|
||||
@@ -2011,7 +2011,7 @@
|
||||
//
|
||||
// Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
|
||||
//
|
||||
//#define INDIVIDUAL_AXIS_HOMING_MENU
|
||||
#define INDIVIDUAL_AXIS_HOMING_MENU
|
||||
|
||||
//
|
||||
// SPEAKER/BUZZER
|
||||
@@ -2019,7 +2019,7 @@
|
||||
// If you have a speaker that can produce tones, enable it here.
|
||||
// By default Marlin assumes you have a buzzer with a fixed frequency.
|
||||
//
|
||||
//#define SPEAKER
|
||||
#define SPEAKER
|
||||
|
||||
//
|
||||
// The duration and frequency for the UI feedback sound.
|
||||
@@ -2200,7 +2200,7 @@
|
||||
// RepRapDiscount FULL GRAPHIC Smart Controller
|
||||
// https://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
|
||||
//
|
||||
//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
|
||||
|
||||
//
|
||||
// K.3D Full Graphic Smart Controller
|
||||
|
||||
+36
-36
@@ -239,11 +239,11 @@
|
||||
*/
|
||||
#if ENABLED(THERMAL_PROTECTION_HOTENDS)
|
||||
#define THERMAL_PROTECTION_PERIOD 40 // Seconds
|
||||
#define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius
|
||||
#define THERMAL_PROTECTION_HYSTERESIS 15 // Degrees Celsius
|
||||
|
||||
//#define ADAPTIVE_FAN_SLOWING // Slow part cooling fan if temperature drops
|
||||
#define ADAPTIVE_FAN_SLOWING // Slow part cooling fan if temperature drops
|
||||
#if BOTH(ADAPTIVE_FAN_SLOWING, PIDTEMP)
|
||||
//#define NO_FAN_SLOWING_IN_PID_TUNING // Don't slow fan speed during M303
|
||||
#define NO_FAN_SLOWING_IN_PID_TUNING // Don't slow fan speed during M303
|
||||
#endif
|
||||
|
||||
/**
|
||||
@@ -437,9 +437,9 @@
|
||||
* Hotend Idle Timeout
|
||||
* Prevent filament in the nozzle from charring and causing a critical jam.
|
||||
*/
|
||||
//#define HOTEND_IDLE_TIMEOUT
|
||||
#define HOTEND_IDLE_TIMEOUT
|
||||
#if ENABLED(HOTEND_IDLE_TIMEOUT)
|
||||
#define HOTEND_IDLE_TIMEOUT_SEC (5*60) // (seconds) Time without extruder movement to trigger protection
|
||||
#define HOTEND_IDLE_TIMEOUT_SEC (15*60) // (seconds) Time without extruder movement to trigger protection
|
||||
#define HOTEND_IDLE_MIN_TRIGGER 180 // (°C) Minimum temperature to enable hotend protection
|
||||
#define HOTEND_IDLE_NOZZLE_TARGET 0 // (°C) Safe temperature for the nozzle after timeout
|
||||
#define HOTEND_IDLE_BED_TARGET 0 // (°C) Safe temperature for the bed after timeout
|
||||
@@ -648,7 +648,7 @@
|
||||
//
|
||||
// For Z set the number of stepper drivers
|
||||
//
|
||||
#define NUM_Z_STEPPER_DRIVERS 1 // (1-4) Z options change based on how many
|
||||
#define NUM_Z_STEPPER_DRIVERS 2 // (1-4) Z options change based on how many
|
||||
|
||||
#if NUM_Z_STEPPER_DRIVERS > 1
|
||||
// Enable if Z motor direction signals are the opposite of Z1
|
||||
@@ -741,7 +741,7 @@
|
||||
|
||||
//#define HOMING_BACKOFF_POST_MM { 2, 2, 2 } // (mm) Backoff from endstops after homing
|
||||
|
||||
//#define QUICK_HOME // If G28 contains XY do a diagonal move first
|
||||
#define QUICK_HOME // If G28 contains XY do a diagonal move first
|
||||
//#define HOME_Y_BEFORE_X // If G28 contains XY home Y before X
|
||||
//#define HOME_Z_FIRST // Home Z first. Requires a Z-MIN endstop (not a probe).
|
||||
//#define CODEPENDENT_XY_HOMING // If X/Y can't home without homing Y/X first
|
||||
@@ -821,7 +821,7 @@
|
||||
* Z Steppers Auto-Alignment
|
||||
* Add the G34 command to align multiple Z steppers using a bed probe.
|
||||
*/
|
||||
//#define Z_STEPPER_AUTO_ALIGN
|
||||
#define Z_STEPPER_AUTO_ALIGN
|
||||
#if ENABLED(Z_STEPPER_AUTO_ALIGN)
|
||||
// Define probe X and Y positions for Z1, Z2 [, Z3 [, Z4]]
|
||||
// If not defined, probe limits will be used.
|
||||
@@ -965,12 +965,12 @@
|
||||
// Backlash Compensation
|
||||
// Adds extra movement to axes on direction-changes to account for backlash.
|
||||
//
|
||||
//#define BACKLASH_COMPENSATION
|
||||
#define BACKLASH_COMPENSATION
|
||||
#if ENABLED(BACKLASH_COMPENSATION)
|
||||
// Define values for backlash distance and correction.
|
||||
// If BACKLASH_GCODE is enabled these values are the defaults.
|
||||
#define BACKLASH_DISTANCE_MM { 0, 0, 0 } // (mm)
|
||||
#define BACKLASH_CORRECTION 0.0 // 0.0 = no correction; 1.0 = full correction
|
||||
#define BACKLASH_CORRECTION 0.1 // 0.0 = no correction; 1.0 = full correction
|
||||
|
||||
// Add steps for motor direction changes on CORE kinematics
|
||||
//#define CORE_BACKLASH
|
||||
@@ -980,7 +980,7 @@
|
||||
//#define BACKLASH_SMOOTHING_MM 3 // (mm)
|
||||
|
||||
// Add runtime configuration and tuning of backlash values (M425)
|
||||
//#define BACKLASH_GCODE
|
||||
#define BACKLASH_GCODE
|
||||
|
||||
#if ENABLED(BACKLASH_GCODE)
|
||||
// Measure the Z backlash when probing (G29) and set with "M425 Z"
|
||||
@@ -1175,7 +1175,7 @@
|
||||
#endif
|
||||
|
||||
// Include a page of printer information in the LCD Main Menu
|
||||
//#define LCD_INFO_MENU
|
||||
#define LCD_INFO_MENU
|
||||
#if ENABLED(LCD_INFO_MENU)
|
||||
//#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages
|
||||
#endif
|
||||
@@ -1229,13 +1229,13 @@
|
||||
#endif
|
||||
|
||||
// Scroll a longer status message into view
|
||||
//#define STATUS_MESSAGE_SCROLLING
|
||||
#define STATUS_MESSAGE_SCROLLING
|
||||
|
||||
// On the Info Screen, display XY with one decimal place when possible
|
||||
//#define LCD_DECIMAL_SMALL_XY
|
||||
|
||||
// Add an 'M73' G-code to set the current percentage
|
||||
//#define LCD_SET_PROGRESS_MANUALLY
|
||||
#define LCD_SET_PROGRESS_MANUALLY
|
||||
|
||||
// Show the E position (filament used) during printing
|
||||
//#define LCD_SHOW_E_TOTAL
|
||||
@@ -1317,7 +1317,7 @@
|
||||
* an option on the LCD screen to continue the print from the last-known
|
||||
* point in the file.
|
||||
*/
|
||||
//#define POWER_LOSS_RECOVERY
|
||||
#define POWER_LOSS_RECOVERY
|
||||
#if ENABLED(POWER_LOSS_RECOVERY)
|
||||
#define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
|
||||
//#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
|
||||
@@ -1383,10 +1383,10 @@
|
||||
//#define UTF_FILENAME_SUPPORT
|
||||
|
||||
// This allows hosts to request long names for files and folders with M33
|
||||
//#define LONG_FILENAME_HOST_SUPPORT
|
||||
#define LONG_FILENAME_HOST_SUPPORT
|
||||
|
||||
// Enable this option to scroll long filenames in the SD card menu
|
||||
//#define SCROLL_LONG_FILENAMES
|
||||
#define SCROLL_LONG_FILENAMES
|
||||
|
||||
// Leave the heaters on after Stop Print (not recommended!)
|
||||
//#define SD_ABORT_NO_COOLDOWN
|
||||
@@ -1408,7 +1408,7 @@
|
||||
/**
|
||||
* Auto-report SdCard status with M27 S<seconds>
|
||||
*/
|
||||
//#define AUTO_REPORT_SD_STATUS
|
||||
#define AUTO_REPORT_SD_STATUS
|
||||
|
||||
/**
|
||||
* Support for USB thumb drives using an Arduino USB Host Shield or
|
||||
@@ -1792,18 +1792,18 @@
|
||||
*
|
||||
* Warning: Does not respect endstops!
|
||||
*/
|
||||
//#define BABYSTEPPING
|
||||
#define BABYSTEPPING
|
||||
#if ENABLED(BABYSTEPPING)
|
||||
//#define INTEGRATED_BABYSTEPPING // EXPERIMENTAL integration of babystepping into the Stepper ISR
|
||||
#define INTEGRATED_BABYSTEPPING // EXPERIMENTAL integration of babystepping into the Stepper ISR
|
||||
//#define BABYSTEP_WITHOUT_HOMING
|
||||
//#define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement).
|
||||
#define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement).
|
||||
//#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA!
|
||||
#define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way
|
||||
//#define BABYSTEP_MILLIMETER_UNITS // Specify BABYSTEP_MULTIPLICATOR_(XY|Z) in mm instead of micro-steps
|
||||
#define BABYSTEP_MULTIPLICATOR_Z 1 // (steps or mm) Steps or millimeter distance for each Z babystep
|
||||
#define BABYSTEP_MULTIPLICATOR_XY 1 // (steps or mm) Steps or millimeter distance for each XY babystep
|
||||
|
||||
//#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
|
||||
#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
|
||||
#if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING)
|
||||
#define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
|
||||
// Note: Extra time may be added to mitigate controller latency.
|
||||
@@ -1815,10 +1815,10 @@
|
||||
|
||||
//#define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28
|
||||
|
||||
//#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping
|
||||
#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping
|
||||
#if ENABLED(BABYSTEP_ZPROBE_OFFSET)
|
||||
//#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
|
||||
//#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
|
||||
#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
|
||||
#endif
|
||||
#endif
|
||||
|
||||
@@ -2140,7 +2140,7 @@
|
||||
* Currently handles M108, M112, M410, M876
|
||||
* NOTE: Not yet implemented for all platforms.
|
||||
*/
|
||||
//#define EMERGENCY_PARSER
|
||||
#define EMERGENCY_PARSER
|
||||
|
||||
/**
|
||||
* Realtime Reporting (requires EMERGENCY_PARSER)
|
||||
@@ -2169,7 +2169,7 @@
|
||||
//#define NO_TIMEOUTS 1000 // Milliseconds
|
||||
|
||||
// Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary.
|
||||
//#define ADVANCED_OK
|
||||
#define ADVANCED_OK
|
||||
|
||||
// Printrun may have trouble receiving long strings all at once.
|
||||
// This option inserts short delays between lines of serial output.
|
||||
@@ -2310,7 +2310,7 @@
|
||||
*
|
||||
* Enable PARK_HEAD_ON_PAUSE to add the G-code M125 Pause and Park.
|
||||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
@@ -2345,14 +2345,14 @@
|
||||
#define FILAMENT_UNLOAD_PURGE_FEEDRATE 25 // (mm/s) feedrate to purge before unload
|
||||
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 2 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // If needed, home before parking for filament change
|
||||
#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
#define HOME_BEFORE_FILAMENT_CHANGE // If needed, home before parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
@@ -3649,10 +3649,10 @@
|
||||
* Host Prompt Support enables Marlin to use the host for user prompts so
|
||||
* filament runout and other processes can be managed from the host side.
|
||||
*/
|
||||
//#define HOST_ACTION_COMMANDS
|
||||
#define HOST_ACTION_COMMANDS
|
||||
#if ENABLED(HOST_ACTION_COMMANDS)
|
||||
//#define HOST_PROMPT_SUPPORT
|
||||
//#define HOST_START_MENU_ITEM // Add a menu item that tells the host to start
|
||||
#define HOST_PROMPT_SUPPORT
|
||||
#define HOST_START_MENU_ITEM // Add a menu item that tells the host to start
|
||||
#endif
|
||||
|
||||
/**
|
||||
@@ -4001,7 +4001,7 @@
|
||||
//
|
||||
// M43 - display pin status, toggle pins, watch pins, watch endstops & toggle LED, test servo probe
|
||||
//
|
||||
//#define PINS_DEBUGGING
|
||||
#define PINS_DEBUGGING
|
||||
|
||||
// Enable Marlin dev mode which adds some special commands
|
||||
//#define MARLIN_DEV_MODE
|
||||
|
||||
Reference in New Issue
Block a user