Bump to 2.0.5

Marlin/Configuration (2).h

@@ -36,7 +36,7 @@
  * Advanced settings can be found in Configuration_adv.h
  *
  */
-#define CONFIGURATION_H_VERSION 020004
+#define CONFIGURATION_H_VERSION 020005
 
 //===========================================================================
 //============================= Getting Started =============================

Marlin/Configuration.h

@@ -41,7 +41,7 @@
  * Advanced settings can be found in Configuration_adv.h
  *
  */
-#define CONFIGURATION_H_VERSION 020004
+#define CONFIGURATION_H_VERSION 020005
 
 //===========================================================================
 //============================= Getting Started =============================
@@ -441,9 +441,9 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-#define TEMP_RESIDENCY_TIME     10  // (seconds) Time to wait for hotend to "settle" in M109
-#define TEMP_WINDOW              1  // (°C) Temperature proximity for the "temperature reached" timer
-#define TEMP_HYSTERESIS          3  // (°C) Temperature proximity considered "close enough" to the target
+#define TEMP_RESIDENCY_TIME      3  // (seconds) Time to wait for hotend to "settle" in M109
+#define TEMP_WINDOW              3  // (°C) Temperature proximity for the "temperature reached" timer
+#define TEMP_HYSTERESIS          5  // (°C) Temperature proximity considered "close enough" to the target
 
 #define TEMP_BED_RESIDENCY_TIME 10  // (seconds) Time to wait for bed to "settle" in M190
 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer

Marlin/Configuration_adv (2).h

@@ -31,7 +31,7 @@
  * Basic settings can be found in Configuration.h
  *
  */
-#define CONFIGURATION_ADV_H_VERSION 020004
+#define CONFIGURATION_ADV_H_VERSION 020005
 
 // @section temperature
 
@@ -1302,9 +1302,9 @@
     #define DGUS_PREHEAT_UI               // Display a preheat screen during heatup
 
     #if ENABLED(DGUS_LCD_UI_FYSETC)
-      //#define DUGS_UI_MOVE_DIS_OPTION   // Disabled by default for UI_FYSETC
+      //#define DGUS_UI_MOVE_DIS_OPTION   // Disabled by default for UI_FYSETC
     #else
-      #define DUGS_UI_MOVE_DIS_OPTION     // Enabled by default for UI_HIPRECY
+      #define DGUS_UI_MOVE_DIS_OPTION     // Enabled by default for UI_HIPRECY
     #endif
 
     #define DGUS_FILAMENT_LOADUNLOAD

Marlin/Configuration_adv.h

@@ -31,7 +31,7 @@
  * Basic settings can be found in Configuration.h
  *
  */
-#define CONFIGURATION_ADV_H_VERSION 020004
+#define CONFIGURATION_ADV_H_VERSION 020005
 
 // @section temperature
 
@@ -1304,9 +1304,9 @@
     #define DGUS_PREHEAT_UI               // Display a preheat screen during heatup
 
     #if ENABLED(DGUS_LCD_UI_FYSETC)
-      //#define DUGS_UI_MOVE_DIS_OPTION   // Disabled by default for UI_FYSETC
+      //#define DGUS_UI_MOVE_DIS_OPTION   // Disabled by default for UI_FYSETC
     #else
-      #define DUGS_UI_MOVE_DIS_OPTION     // Enabled by default for UI_HIPRECY
+      #define DGUS_UI_MOVE_DIS_OPTION     // Enabled by default for UI_HIPRECY
     #endif
 
     #define DGUS_FILAMENT_LOADUNLOAD

Marlin/src/HAL/AVR/HAL_SPI.cpp

@@ -197,7 +197,7 @@ void spiBegin() {
     // output pin high - like sending 0xFF
     WRITE(MOSI_PIN, HIGH);
 
-    for (uint8_t i = 0; i < 8; i++) {
+    LOOP_L_N(i, 8) {
       WRITE(SCK_PIN, HIGH);
 
       nop; // adjust so SCK is nice
@@ -224,7 +224,7 @@ void spiBegin() {
   void spiSend(uint8_t data) {
     // no interrupts during byte send - about 8µs
     cli();
-    for (uint8_t i = 0; i < 8; i++) {
+    LOOP_L_N(i, 8) {
       WRITE(SCK_PIN, LOW);
       WRITE(MOSI_PIN, data & 0x80);
       data <<= 1;

Marlin/src/HAL/AVR/MarlinSerial.cpp

@@ -55,7 +55,7 @@
   // A SW memory barrier, to ensure GCC does not overoptimize loops
   #define sw_barrier() asm volatile("": : :"memory");
 
-  #include "../../feature/emergency_parser.h"
+  #include "../../feature/e_parser.h"
 
   // "Atomically" read the RX head index value without disabling interrupts:
   // This MUST be called with RX interrupts enabled, and CAN'T be called
@@ -682,7 +682,7 @@
 
     // Round correctly so that print(1.999, 2) prints as "2.00"
     double rounding = 0.5;
-    for (uint8_t i = 0; i < digits; ++i) rounding *= 0.1;
+    LOOP_L_N(i, digits) rounding *= 0.1;
     number += rounding;
 
     // Extract the integer part of the number and print it

Marlin/src/HAL/AVR/fast_pwm.cpp

@@ -167,7 +167,7 @@ void set_pwm_frequency(const pin_t pin, int f_desired) {
     uint16_t prescaler[] = { 0, 1, 8, /*TIMER2 ONLY*/32, 64, /*TIMER2 ONLY*/128, 256, 1024 };
 
     // loop over prescaler values
-    for (uint8_t i = 1; i < 8; i++) {
+    LOOP_S_L_N(i, 1, 8) {
       uint16_t res_temp_fast = 255, res_temp_phase_correct = 255;
       if (timer.n == 2) {
         // No resolution calculation for TIMER2 unless enabled USE_OCR2A_AS_TOP

Marlin/src/HAL/AVR/pinsDebug.h

@@ -70,12 +70,12 @@
 
 void PRINT_ARRAY_NAME(uint8_t x) {
   char *name_mem_pointer = (char*)pgm_read_ptr(&pin_array[x].name);
-  for (uint8_t y = 0; y < MAX_NAME_LENGTH; y++) {
+  LOOP_L_N(y, MAX_NAME_LENGTH) {
     char temp_char = pgm_read_byte(name_mem_pointer + y);
     if (temp_char != 0)
       SERIAL_CHAR(temp_char);
     else {
-      for (uint8_t i = 0; i < MAX_NAME_LENGTH - y; i++) SERIAL_CHAR(' ');
+      LOOP_L_N(i, MAX_NAME_LENGTH - y) SERIAL_CHAR(' ');
       break;
     }
   }

Marlin/src/HAL/AVR/u8g_com_HAL_AVR_sw_spi.cpp

@@ -88,7 +88,7 @@ void u8g_spiSend_sw_AVR_mode_0(uint8_t val) {
   volatile uint8_t *outData = u8g_outData,
                    *outClock = u8g_outClock;
   U8G_ATOMIC_START();
-  for (uint8_t i = 0; i < 8; i++) {
+  LOOP_L_N(i, 8) {
     if (val & 0x80)
       *outData |= bitData;
     else
@@ -108,7 +108,7 @@ void u8g_spiSend_sw_AVR_mode_3(uint8_t val) {
   volatile uint8_t *outData = u8g_outData,
                    *outClock = u8g_outClock;
   U8G_ATOMIC_START();
-  for (uint8_t i = 0; i < 8; i++) {
+  LOOP_L_N(i, 8) {
     *outClock &= bitNotClock;
     if (val & 0x80)
       *outData |= bitData;

Marlin/src/HAL/DUE/MarlinSerial.cpp

@@ -45,7 +45,7 @@ template<typename Cfg> typename MarlinSerial<Cfg>::ring_buffer_pos_t MarlinSeria
 // A SW memory barrier, to ensure GCC does not overoptimize loops
 #define sw_barrier() asm volatile("": : :"memory");
 
-#include "../../feature/emergency_parser.h"
+#include "../../feature/e_parser.h"
 
 // (called with RX interrupts disabled)
 template<typename Cfg>
@@ -606,7 +606,7 @@ void MarlinSerial<Cfg>::printFloat(double number, uint8_t digits) {
 
   // Round correctly so that print(1.999, 2) prints as "2.00"
   double rounding = 0.5;
-  for (uint8_t i = 0; i < digits; ++i) rounding *= 0.1;
+  LOOP_L_N(i, digits) rounding *= 0.1;
   number += rounding;
 
   // Extract the integer part of the number and print it

Marlin/src/HAL/DUE/MarlinSerialUSB.cpp

@@ -34,7 +34,7 @@
 #include "MarlinSerialUSB.h"
 
 #if ENABLED(EMERGENCY_PARSER)
-  #include "../../feature/emergency_parser.h"
+  #include "../../feature/e_parser.h"
 #endif
 
 // Imports from Atmel USB Stack/CDC implementation
@@ -259,7 +259,7 @@ void MarlinSerialUSB::printFloat(double number, uint8_t digits) {
 
   // Round correctly so that print(1.999, 2) prints as "2.00"
   double rounding = 0.5;
-  for (uint8_t i = 0; i < digits; ++i)
+  LOOP_L_N(i, digits)
     rounding *= 0.1;
 
   number += rounding;

Marlin/src/HAL/DUE/dogm/u8g_com_HAL_DUE_sw_spi_shared.cpp

@@ -80,7 +80,7 @@ Pio *SCK_pPio, *MOSI_pPio;
 uint32_t SCK_dwMask, MOSI_dwMask;
 
 void u8g_spiSend_sw_DUE_mode_0(uint8_t val) { // 3MHz
-  for (uint8_t i = 0; i < 8; i++) {
+  LOOP_L_N(i, 8) {
     if (val & 0x80)
       MOSI_pPio->PIO_SODR = MOSI_dwMask;
     else
@@ -94,7 +94,7 @@ void u8g_spiSend_sw_DUE_mode_0(uint8_t val) { // 3MHz
 }
 
 void u8g_spiSend_sw_DUE_mode_3(uint8_t val) { // 3.5MHz
-  for (uint8_t i = 0; i < 8; i++) {
+  LOOP_L_N(i, 8) {
     SCK_pPio->PIO_CODR = SCK_dwMask;
     DELAY_NS(50);
     if (val & 0x80)

Marlin/src/HAL/DUE/fastio/G2_PWM.h

@@ -63,7 +63,7 @@ extern PWM_map ISR_table[NUM_PWMS];
 extern uint32_t motor_current_setting[3];
 
 #define IR_BIT(p) (WITHIN(p, 0, 3) ? (p) : (p) + 4)
-#define COPY_ACTIVE_TABLE() do{ for (uint8_t i = 0; i < 6 ; i++) work_table[i] = active_table[i]; }while(0)
+#define COPY_ACTIVE_TABLE() do{ LOOP_L_N(i, 6) work_table[i] = active_table[i]; }while(0)
 
 #define PWM_MR0 19999         // base repetition rate minus one count - 20mS
 #define PWM_PR 24             // prescaler value - prescaler divide by 24 + 1  -  1 MHz output