Ender config updates
This commit is contained in:
InsanityAutomation
+21
-11
@@ -317,6 +317,7 @@
|
||||
#endif
|
||||
|
||||
#if ENABLED(MachineCR20Pro)
|
||||
#define LCD_CONTRAST_INIT 165
|
||||
#define MachineCR20
|
||||
#if DISABLED(ABL_EZABL) && DISABLED(ABL_NCSW)
|
||||
#define ABL_BLTOUCH
|
||||
@@ -858,7 +859,7 @@
|
||||
#define PID_MAX BANG_MAX // Limits current to nozzle while PID is active (see PID_FUNCTIONAL_RANGE below); 255=full current
|
||||
#define PID_K1 0.95 // Smoothing factor within any PID loop
|
||||
#if ENABLED(PIDTEMP)
|
||||
#if NONE(MachineCR10Orig, LowMemoryBoard)
|
||||
#if DISABLED(LowMemoryBoard)
|
||||
#define PID_EDIT_MENU
|
||||
#define PID_AUTOTUNE_MENU // Add PID Autotune to the LCD "Temperature" menu to run M303 and apply the result.
|
||||
#endif
|
||||
@@ -988,9 +989,8 @@
|
||||
*
|
||||
* *** IT IS HIGHLY RECOMMENDED TO LEAVE THIS OPTION ENABLED! ***
|
||||
*/
|
||||
#if DISABLED(MachineCR10Orig)
|
||||
#define PREVENT_COLD_EXTRUSION
|
||||
#define EXTRUDE_MINTEMP 160
|
||||
#define EXTRUDE_MINTEMP 170
|
||||
|
||||
/**
|
||||
* Prevent a single extrusion longer than EXTRUDE_MAXLENGTH.
|
||||
@@ -998,7 +998,7 @@
|
||||
*/
|
||||
#define PREVENT_LENGTHY_EXTRUDE
|
||||
#define EXTRUDE_MAXLENGTH 500
|
||||
#endif
|
||||
|
||||
//===========================================================================
|
||||
//======================== Thermal Runaway Protection =======================
|
||||
//===========================================================================
|
||||
@@ -1578,7 +1578,11 @@
|
||||
* Example: `M851 Z-5` with a CLEARANCE of 4 => 9mm from bed to nozzle.
|
||||
* But: `M851 Z+1` with a CLEARANCE of 2 => 2mm from bed to nozzle.
|
||||
*/
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow
|
||||
#if ANY(MachineEnder5, MachineEnder5Plus)
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 0 // Z Clearance for Deploy/Stow
|
||||
#else
|
||||
#define Z_CLEARANCE_DEPLOY_PROBE 10 // Z Clearance for Deploy/Stow
|
||||
#endif
|
||||
#define Z_CLEARANCE_BETWEEN_PROBES 5 // Z Clearance between probe points
|
||||
#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes
|
||||
#define Z_AFTER_PROBING 5 // Z position after probing is done
|
||||
@@ -1699,9 +1703,12 @@
|
||||
//#define NO_MOTION_BEFORE_HOMING // Inhibit movement until all axes have been homed
|
||||
|
||||
//#define UNKNOWN_Z_NO_RAISE // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
|
||||
|
||||
#if ANY(MachineEnder5, MachineEnder5Plus)
|
||||
#define Z_HOMING_HEIGHT 0
|
||||
#else
|
||||
#define Z_HOMING_HEIGHT 4 // (in mm) Minimal z height before homing (G28) for Z clearance above the bed, clamps, ...
|
||||
// Be sure you have this distance over your Z_MAX_POS in case.
|
||||
#endif
|
||||
|
||||
// Direction of endstops when homing; 1=MAX, -1=MIN
|
||||
// :[-1,1]
|
||||
@@ -1734,8 +1741,8 @@
|
||||
#define Y_BED_SIZE 230
|
||||
#define Z_MAX_POS 250
|
||||
#elif ANY(MachineEnder4, MachineEnder5)
|
||||
#define X_BED_SIZE 220
|
||||
#define Y_BED_SIZE 220
|
||||
#define X_BED_SIZE 230
|
||||
#define Y_BED_SIZE 225
|
||||
#define Z_MAX_POS 300
|
||||
#elif ENABLED(MachineEnder5Plus)
|
||||
#define X_BED_SIZE 360
|
||||
@@ -2089,7 +2096,7 @@
|
||||
* Add a bed leveling sub-menu for ABL or MBL.
|
||||
* Include a guided procedure if manual probing is enabled.
|
||||
*/
|
||||
#if NONE(ABL_EZABL, ABL_NCSW, ABL_BLTOUCH, MachineCR10Orig) && (DISABLED(MachineCRX) || ENABLED(GraphicLCD))
|
||||
#if NONE(ABL_EZABL, ABL_NCSW, ABL_BLTOUCH) && (DISABLED(MachineCRX) || ENABLED(GraphicLCD))
|
||||
#define LCD_BED_LEVELING
|
||||
#endif
|
||||
|
||||
@@ -2098,7 +2105,7 @@
|
||||
#define LCD_PROBE_Z_RANGE 8 // Z Range centered on Z_MIN_POS for LCD Z adjustment
|
||||
#endif
|
||||
|
||||
#if NONE(MachineCR10Orig, SolidBedMounts)
|
||||
#if NONE(SolidBedMounts)
|
||||
// Add a menu item to move between bed corners for manual bed adjustment
|
||||
#define LEVEL_BED_CORNERS
|
||||
#endif
|
||||
@@ -2153,6 +2160,9 @@
|
||||
#elif ENABLED(MachineCRX)
|
||||
#define Z_SAFE_HOMING_X_POINT 50 + HOMING_ADD // X point for Z homing when homing all axis (G28).
|
||||
#define Z_SAFE_HOMING_Y_POINT 70 + HOMING_ADD // Y point for Z homing when homing all axis (G28).
|
||||
#elif ANY(MachineEnder5, MachineEnder5Plus)
|
||||
#define Z_SAFE_HOMING_X_POINT 110 + HOMING_ADD // X point for Z homing when homing all axis (G28).
|
||||
#define Z_SAFE_HOMING_Y_POINT 110 + HOMING_ADD // Y point for Z homing when homing all axis (G28).
|
||||
#else
|
||||
#define Z_SAFE_HOMING_X_POINT 50 + HOMING_ADD // X point for Z homing when homing all axis (G28).
|
||||
#define Z_SAFE_HOMING_Y_POINT 50 + HOMING_ADD // Y point for Z homing when homing all axis (G28).
|
||||
@@ -2239,7 +2249,7 @@
|
||||
* M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
|
||||
*/
|
||||
#define EEPROM_SETTINGS // Persistent storage with M500 and M501
|
||||
#if NONE(MachineCR10Orig, LowMemoryBoard)
|
||||
#if DISABLED(LowMemoryBoard)
|
||||
#define EEPROM_CHITCHAT // Give feedback on EEPROM commands. Disable to save PROGMEM.
|
||||
#else
|
||||
#define DISABLE_M503 // Saves ~2700 bytes of PROGMEM. Disable for release!
|
||||
|
||||
@@ -673,7 +673,9 @@
|
||||
#define DEFAULT_MINIMUMFEEDRATE 0.0 // minimum feedrate
|
||||
#define DEFAULT_MINTRAVELFEEDRATE 0.0
|
||||
|
||||
//#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated
|
||||
#if ANY(MachineEnder5, MachineEnder5Plus)
|
||||
#define HOME_AFTER_DEACTIVATE // Require rehoming after steppers are deactivated
|
||||
#endif
|
||||
|
||||
// Minimum time that a segment needs to take if the buffer is emptied
|
||||
#define DEFAULT_MINSEGMENTTIME 20000 // (ms)
|
||||
|
||||
Reference in New Issue
Block a user