Update Configuration.h
This commit is contained in:
InsanityAutomation
+39
-22
@@ -5,10 +5,11 @@
|
||||
//#define FilamentSensorLerdge
|
||||
//#define SKR13 // 32 bit board - assumes 2208 drivers
|
||||
//#define SKR13_2209
|
||||
#define SKR_E_8825
|
||||
//#define SKR13_UART // Configure SKR board with drivers in UART mode
|
||||
//#define DUAL_Z
|
||||
//#define GRAPHICSLCD
|
||||
|
||||
#define UBL
|
||||
|
||||
/**
|
||||
* Marlin 3D Printer Firmware
|
||||
@@ -687,21 +688,30 @@
|
||||
* :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
|
||||
*/
|
||||
|
||||
#if ENABLED(SKR13, SKR_E_8825)
|
||||
#define E0_DRIVER_TYPE DRV8825
|
||||
#define E1_DRIVER_TYPE DRV8825
|
||||
#endif
|
||||
|
||||
#if ENABLED(SKR13) && DISABLED(SKR13_UART)
|
||||
#if ENABLED(SKR13_2209)
|
||||
#define X_DRIVER_TYPE TMC2209_STANDALONE
|
||||
#define Y_DRIVER_TYPE TMC2209_STANDALONE
|
||||
#define Z_DRIVER_TYPE TMC2209_STANDALONE
|
||||
#define Z2_DRIVER_TYPE TMC2209_STANDALONE
|
||||
#define E0_DRIVER_TYPE TMC2209_STANDALONE
|
||||
#define E1_DRIVER_TYPE TMC2209_STANDALONE
|
||||
#if DISABLED(SKR_E_8825)
|
||||
#define E0_DRIVER_TYPE TMC2209_STANDALONE
|
||||
#define E1_DRIVER_TYPE TMC2209_STANDALONE
|
||||
#endif
|
||||
#else
|
||||
#define X_DRIVER_TYPE TMC2208_STANDALONE
|
||||
#define Y_DRIVER_TYPE TMC2208_STANDALONE
|
||||
#define Z_DRIVER_TYPE TMC2208_STANDALONE
|
||||
#define Z2_DRIVER_TYPE TMC2208_STANDALONE
|
||||
#define E0_DRIVER_TYPE TMC2208_STANDALONE
|
||||
#define E1_DRIVER_TYPE TMC2208_STANDALONE
|
||||
#if DISABLED(SKR_E_8825)
|
||||
#define E0_DRIVER_TYPE TMC2208_STANDALONE
|
||||
#define E1_DRIVER_TYPE TMC2208_STANDALONE
|
||||
#endif
|
||||
#endif
|
||||
#elif ENABLED(SKR13, SKR13_UART)
|
||||
#if ENABLED(SKR13_2209)
|
||||
@@ -709,15 +719,19 @@
|
||||
#define Y_DRIVER_TYPE TMC2209
|
||||
#define Z_DRIVER_TYPE TMC2209
|
||||
#define Z2_DRIVER_TYPE TMC2209
|
||||
#define E0_DRIVER_TYPE TMC2209
|
||||
#define E1_DRIVER_TYPE TMC2209
|
||||
#if DISABLED(SKR_E_8825)
|
||||
#define E0_DRIVER_TYPE TMC2209
|
||||
#define E1_DRIVER_TYPE TMC2209
|
||||
#endif
|
||||
#else
|
||||
#define X_DRIVER_TYPE TMC2208
|
||||
#define Y_DRIVER_TYPE TMC2208
|
||||
#define Z_DRIVER_TYPE TMC2208
|
||||
#define Z2_DRIVER_TYPE TMC2208
|
||||
#define E0_DRIVER_TYPE TMC2208
|
||||
#define E1_DRIVER_TYPE TMC2208
|
||||
#if DISABLED(SKR_E_8825)
|
||||
#define E0_DRIVER_TYPE TMC2208
|
||||
#define E1_DRIVER_TYPE TMC2208
|
||||
#endif
|
||||
#endif
|
||||
#else
|
||||
#define X_DRIVER_TYPE A4988
|
||||
@@ -983,7 +997,7 @@
|
||||
#define Z_PROBE_OFFSET_FROM_EXTRUDER 0 // Z offset: -below +above [the nozzle]
|
||||
|
||||
// Certain types of probes need to stay away from edges
|
||||
#define MIN_PROBE_EDGE 10
|
||||
#define MIN_PROBE_EDGE 5
|
||||
|
||||
// X and Y axis travel speed (mm/m) between probes
|
||||
#define XY_PROBE_SPEED 3000
|
||||
@@ -1025,7 +1039,7 @@
|
||||
#define Z_CLEARANCE_MULTI_PROBE 5 // Z Clearance between multiple probes
|
||||
//#define Z_AFTER_PROBING 5 // Z position after probing is done
|
||||
|
||||
#define Z_PROBE_LOW_POINT -2 // Farthest distance below the trigger-point to go before stopping
|
||||
#define Z_PROBE_LOW_POINT -3 // Farthest distance below the trigger-point to go before stopping
|
||||
|
||||
// For M851 give a range for adjusting the Z probe offset
|
||||
#define Z_PROBE_OFFSET_RANGE_MIN -20
|
||||
@@ -1242,8 +1256,11 @@
|
||||
*/
|
||||
//#define AUTO_BED_LEVELING_3POINT
|
||||
//#define AUTO_BED_LEVELING_LINEAR
|
||||
#define AUTO_BED_LEVELING_BILINEAR
|
||||
//#define AUTO_BED_LEVELING_UBL
|
||||
#if DISABLED(UBL)
|
||||
#define AUTO_BED_LEVELING_BILINEAR
|
||||
#else
|
||||
#define AUTO_BED_LEVELING_UBL
|
||||
#endif
|
||||
//#define MESH_BED_LEVELING
|
||||
|
||||
/**
|
||||
@@ -1288,7 +1305,7 @@
|
||||
#if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR)
|
||||
|
||||
// Set the number of grid points per dimension.
|
||||
#define GRID_MAX_POINTS_X 4
|
||||
#define GRID_MAX_POINTS_X 10
|
||||
#define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
|
||||
|
||||
// Set the boundaries for probing (where the probe can reach).
|
||||
@@ -1355,24 +1372,24 @@
|
||||
* Override if the automatically selected points are inadequate.
|
||||
*/
|
||||
#if EITHER(AUTO_BED_LEVELING_3POINT, AUTO_BED_LEVELING_UBL)
|
||||
//#define PROBE_PT_1_X 15
|
||||
//#define PROBE_PT_1_Y 180
|
||||
//#define PROBE_PT_2_X 15
|
||||
//#define PROBE_PT_2_Y 20
|
||||
//#define PROBE_PT_3_X 170
|
||||
//#define PROBE_PT_3_Y 20
|
||||
#define PROBE_PT_1_X 50
|
||||
#define PROBE_PT_1_Y 350
|
||||
#define PROBE_PT_2_X 350
|
||||
#define PROBE_PT_2_Y 350
|
||||
#define PROBE_PT_3_X 350
|
||||
#define PROBE_PT_3_Y 50
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Add a bed leveling sub-menu for ABL or MBL.
|
||||
* Include a guided procedure if manual probing is enabled.
|
||||
*/
|
||||
//#define LCD_BED_LEVELING
|
||||
#define LCD_BED_LEVELING
|
||||
|
||||
#if ENABLED(LCD_BED_LEVELING)
|
||||
#define MESH_EDIT_Z_STEP 0.025 // (mm) Step size while manually probing Z axis.
|
||||
#define LCD_PROBE_Z_RANGE 4 // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment
|
||||
//#define MESH_EDIT_MENU // Add a menu to edit mesh points
|
||||
#define MESH_EDIT_MENU // Add a menu to edit mesh points
|
||||
#endif
|
||||
|
||||
// Add a menu item to move between bed corners for manual bed adjustment
|
||||
|
||||
Reference in New Issue
Block a user