jessikitty/Marlin
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity

Merge pull request #1 from MarlinFirmware/bugfix-1.1.x

Browse Source 
Bugfix 1.1.x
This commit is contained in:
InsanityAutomation
2018-04-24 09:49:15 -04:00
committed by GitHub
parent 31261d0c17 21f5ca6ad4
commit baae6ddfef
173 changed files with 2525 additions and 1059 deletions
Download Patch File Download Diff File Expand all files Collapse all files
.travis.yml
+1 -1
View File
@@ -95,7 +95,7 @@ script:
- opt_enable REPRAP_DISCOUNT_SMART_CONTROLLER SDSUPPORT EEPROM_SETTINGS
- opt_enable BLINKM PCA9632 RGB_LED NEOPIXEL_LED AUTO_POWER_CONTROL NOZZLE_PARK_FEATURE FILAMENT_RUNOUT_SENSOR
- opt_enable AUTO_BED_LEVELING_LINEAR Z_MIN_PROBE_REPEATABILITY_TEST DEBUG_LEVELING_FEATURE SKEW_CORRECTION SKEW_CORRECTION_FOR_Z SKEW_CORRECTION_GCODE
- opt_enable_adv ARC_P_CIRCLES ADVANCED_PAUSE_FEATURE CNC_WORKSPACE_PLANES CNC_COORDINATE_SYSTEMS
- opt_enable_adv ARC_P_CIRCLES ADVANCED_PAUSE_FEATURE CNC_WORKSPACE_PLANES CNC_COORDINATE_SYSTEMS POWER_LOSS_RECOVERY
- opt_enable_adv FWRETRACT MAX7219_DEBUG LED_CONTROL_MENU CASE_LIGHT_ENABLE CASE_LIGHT_USE_NEOPIXEL CODEPENDENT_XY_HOMING
- opt_set GRID_MAX_POINTS_X 16
- opt_set_adv FANMUX0_PIN 53
Marlin/Conditionals_post.h
+10 -4
View File
@@ -696,7 +696,6 @@
#define HAS_TEMP_HOTEND (HAS_TEMP_0 || ENABLED(HEATER_0_USES_MAX6675))
#define HAS_TEMP_BED (PIN_EXISTS(TEMP_BED) && TEMP_SENSOR_BED != 0 && TEMP_SENSOR_BED > -2)
#define HAS_TEMP_CHAMBER (PIN_EXISTS(TEMP_CHAMBER) && TEMP_SENSOR_CHAMBER != 0 && TEMP_SENSOR_CHAMBER > -2)
#define HAS_TEMP_SENSOR (HAS_TEMP_HOTEND || HAS_TEMP_BED || HAS_TEMP_CHAMBER)
// Heaters
#define HAS_HEATER_0 (PIN_EXISTS(HEATER_0))
@@ -706,8 +705,11 @@
#define HAS_HEATER_4 (PIN_EXISTS(HEATER_4))
#define HAS_HEATER_BED (PIN_EXISTS(HEATER_BED))
#define HAS_HEATED_BED (HAS_TEMP_BED && HAS_HEATER_BED)
#define HAS_TEMP_SENSOR (HAS_TEMP_HOTEND || HAS_HEATED_BED || HAS_TEMP_CHAMBER)
// Thermal protection
#define HAS_THERMALLY_PROTECTED_BED (ENABLED(THERMAL_PROTECTION_BED) && HAS_TEMP_BED && HAS_HEATER_BED)
#define HAS_THERMALLY_PROTECTED_BED (HAS_HEATED_BED && ENABLED(THERMAL_PROTECTION_BED))
#define WATCH_HOTENDS (ENABLED(THERMAL_PROTECTION_HOTENDS) && WATCH_TEMP_PERIOD > 0)
#define WATCH_THE_BED (HAS_THERMALLY_PROTECTED_BED && WATCH_BED_TEMP_PERIOD > 0)
@@ -804,7 +806,7 @@
/**
* Heated bed requires settings
*/
#if HAS_HEATER_BED
#if HAS_HEATED_BED
#ifndef MAX_BED_POWER
#define MAX_BED_POWER 255
#endif
@@ -946,6 +948,10 @@
#define PLANNER_LEVELING (OLDSCHOOL_ABL || ENABLED(MESH_BED_LEVELING) || UBL_SEGMENTED || ENABLED(SKEW_CORRECTION))
#define HAS_PROBING_PROCEDURE (HAS_ABL || ENABLED(Z_MIN_PROBE_REPEATABILITY_TEST))
#if ENABLED(AUTO_BED_LEVELING_UBL)
#undef LCD_BED_LEVELING
#endif
/**
* Heater & Fan Pausing
*/
@@ -1221,7 +1227,7 @@
#define GRID_MAX_POINTS ((GRID_MAX_POINTS_X) * (GRID_MAX_POINTS_Y))
// Add commands that need sub-codes to this list
#define USE_GCODE_SUBCODES ENABLED(G38_PROBE_TARGET) || ENABLED(CNC_COORDINATE_SYSTEMS)
#define USE_GCODE_SUBCODES ENABLED(G38_PROBE_TARGET) || ENABLED(CNC_COORDINATE_SYSTEMS) || ENABLED(POWER_LOSS_RECOVERY)
// Parking Extruder
#if ENABLED(PARKING_EXTRUDER)
Marlin/Configuration.h
+8
View File
@@ -672,6 +672,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1040,6 +1043,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/Configuration_adv.h
+10
View File
@@ -555,6 +555,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/G26_Mesh_Validation_Tool.cpp
+2 -2
View File
@@ -481,7 +481,7 @@
*/
inline bool turn_on_heaters() {
millis_t next = millis() + 5000UL;
#if HAS_TEMP_BED
#if HAS_HEATED_BED
#if ENABLED(ULTRA_LCD)
if (g26_bed_temp > 25) {
lcd_setstatusPGM(PSTR("G26 Heating Bed."), 99);
@@ -841,7 +841,7 @@
#endif
if (!g26_keep_heaters_on) {
#if HAS_TEMP_BED
#if HAS_HEATED_BED
thermalManager.setTargetBed(0);
#endif
thermalManager.setTargetHotend(0, 0);
Marlin/M100_Free_Mem_Chk.cpp
-2
View File
@@ -59,8 +59,6 @@
#define TEST_BYTE ((char) 0xE5)
extern char command_queue[BUFSIZE][MAX_CMD_SIZE];
extern char* __brkval;
extern size_t __heap_start, __heap_end, __flp;
extern char __bss_end;
Marlin/Makefile
+276 -295
View File
@@ -96,319 +96,296 @@ RELOC_WORKAROUND ?= 1
# HARDWARE_VARIANT = "arduino", "Sanguino", "Gen7", ...
# MCU = "atmega1280", "Mega2560", "atmega2560", "atmega644p", ...
#Gen7
ifeq ($(HARDWARE_MOTHERBOARD),10)
ifeq ($(HARDWARE_MOTHERBOARD),0)
# No motherboard selected
#
# RAMPS 1.3 / 1.4 - ATmega1280, ATmega2560
#
# MEGA/RAMPS up to 1.2
else ifeq ($(HARDWARE_MOTHERBOARD),3)
# RAMPS 1.3 (Power outputs: Hotend, Fan, Bed)
else ifeq ($(HARDWARE_MOTHERBOARD),33)
# RAMPS 1.3 (Power outputs: Hotend0, Hotend1, Bed)
else ifeq ($(HARDWARE_MOTHERBOARD),34)
# RAMPS 1.3 (Power outputs: Hotend, Fan0, Fan1)
else ifeq ($(HARDWARE_MOTHERBOARD),35)
# RAMPS 1.3 (Power outputs: Hotend0, Hotend1, Fan)
else ifeq ($(HARDWARE_MOTHERBOARD),36)
# RAMPS 1.3 (Power outputs: Spindle, Controller Fan)
else ifeq ($(HARDWARE_MOTHERBOARD),38)
# RAMPS 1.4 (Power outputs: Hotend, Fan, Bed)
else ifeq ($(HARDWARE_MOTHERBOARD),43)
# RAMPS 1.4 (Power outputs: Hotend0, Hotend1, Bed)
else ifeq ($(HARDWARE_MOTHERBOARD),44)
# RAMPS 1.4 (Power outputs: Hotend, Fan0, Fan1)
else ifeq ($(HARDWARE_MOTHERBOARD),45)
# RAMPS 1.4 (Power outputs: Hotend0, Hotend1, Fan)
else ifeq ($(HARDWARE_MOTHERBOARD),46)
# RAMPS 1.4 (Power outputs: Spindle, Controller Fan)
else ifeq ($(HARDWARE_MOTHERBOARD),48)
# RAMPS Plus 3DYMY (Power outputs: Hotend, Fan, Bed)
else ifeq ($(HARDWARE_MOTHERBOARD),143)
# RAMPS Plus 3DYMY (Power outputs: Hotend0, Hotend1, Bed)
else ifeq ($(HARDWARE_MOTHERBOARD),144)
# RAMPS Plus 3DYMY (Power outputs: Hotend, Fan0, Fan1)
else ifeq ($(HARDWARE_MOTHERBOARD),145)
# RAMPS Plus 3DYMY (Power outputs: Hotend0, Hotend1, Fan)
else ifeq ($(HARDWARE_MOTHERBOARD),146)
# RAMPS Plus 3DYMY (Power outputs: Spindle, Controller Fan)
else ifeq ($(HARDWARE_MOTHERBOARD),148)
#
# RAMPS Derivatives - ATmega1280, ATmega2560
#
# 3Drag Controller
else ifeq ($(HARDWARE_MOTHERBOARD),77)
# Velleman K8200 Controller (derived from 3Drag Controller)
else ifeq ($(HARDWARE_MOTHERBOARD),78)
# Velleman K8400 Controller (derived from 3Drag Controller)
else ifeq ($(HARDWARE_MOTHERBOARD),79)
# 2PrintBeta BAM&DICE with STK drivers
else ifeq ($(HARDWARE_MOTHERBOARD),401)
# 2PrintBeta BAM&DICE Due with STK drivers
else ifeq ($(HARDWARE_MOTHERBOARD),402)
# MKS BASE v1.0
else ifeq ($(HARDWARE_MOTHERBOARD),40)
# MKS v1.5 with Allegro A4982 stepper drivers
else ifeq ($(HARDWARE_MOTHERBOARD),405)
# MKS BASE 1.0 with Heroic HR4982 stepper drivers
else ifeq ($(HARDWARE_MOTHERBOARD),41)
# MKS GEN v1.3 or 1.4
else ifeq ($(HARDWARE_MOTHERBOARD),47)
# MKS GEN L
else ifeq ($(HARDWARE_MOTHERBOARD),53)
# zrib V2.0 control board (Chinese knock off RAMPS replica)
else ifeq ($(HARDWARE_MOTHERBOARD),504)
# Felix 2.0+ Electronics Board (RAMPS like)
else ifeq ($(HARDWARE_MOTHERBOARD),37)
# Invent-A-Part RigidBoard
else ifeq ($(HARDWARE_MOTHERBOARD),42)
# Invent-A-Part RigidBoard V2
else ifeq ($(HARDWARE_MOTHERBOARD),52)
# Sainsmart 2-in-1 board
else ifeq ($(HARDWARE_MOTHERBOARD),49)
# Ultimaker
else ifeq ($(HARDWARE_MOTHERBOARD),7)
# Ultimaker (Older electronics. Pre 1.5.4. This is rare)
else ifeq ($(HARDWARE_MOTHERBOARD),71)
MCU ?= atmega1280
# Azteeg X3
else ifeq ($(HARDWARE_MOTHERBOARD),67)
# Azteeg X3 Pro
else ifeq ($(HARDWARE_MOTHERBOARD),68)
# Ultimainboard 2.x (Uses TEMP_SENSOR 20)
else ifeq ($(HARDWARE_MOTHERBOARD),72)
# Rumba
else ifeq ($(HARDWARE_MOTHERBOARD),80)
# bq ZUM Mega 3D
else ifeq ($(HARDWARE_MOTHERBOARD),503)
# MakeBoard Mini v2.1.2 is a control board sold by MicroMake
else ifeq ($(HARDWARE_MOTHERBOARD),431)
# TriGorilla Anycubic version 1.3 based on RAMPS EFB
else ifeq ($(HARDWARE_MOTHERBOARD),343)
# TriGorilla Anycubic version 1.4 based on RAMPS EFB
else ifeq ($(HARDWARE_MOTHERBOARD),443)
# Creality: Ender-4, CR-8
else ifeq ($(HARDWARE_MOTHERBOARD),243)
#
# Other ATmega1280, ATmega2560
#
# Cartesio CN Controls V11
else ifeq ($(HARDWARE_MOTHERBOARD),111)
# Cartesio CN Controls V12
else ifeq ($(HARDWARE_MOTHERBOARD),112)
# Cheaptronic v1.0
else ifeq ($(HARDWARE_MOTHERBOARD),2)
# Cheaptronic v2.0
else ifeq ($(HARDWARE_MOTHERBOARD),21)
# Makerbot Mightyboard Revision E
else ifeq ($(HARDWARE_MOTHERBOARD),200)
# Megatronics
else ifeq ($(HARDWARE_MOTHERBOARD),70)
# Megatronics v2.0
else ifeq ($(HARDWARE_MOTHERBOARD),701)
# Megatronics v3.0
else ifeq ($(HARDWARE_MOTHERBOARD),703)
# Megatronics v3.1
else ifeq ($(HARDWARE_MOTHERBOARD),704)
# Rambo
else ifeq ($(HARDWARE_MOTHERBOARD),301)
# Mini-Rambo
else ifeq ($(HARDWARE_MOTHERBOARD),302)
# Mini-Rambo 1.0a
else ifeq ($(HARDWARE_MOTHERBOARD),303)
# Einsy Rambo
else ifeq ($(HARDWARE_MOTHERBOARD),304)
# Einsy Retro
else ifeq ($(HARDWARE_MOTHERBOARD),305)
# Elefu Ra Board (v3)
else ifeq ($(HARDWARE_MOTHERBOARD),21)
# Leapfrog
else ifeq ($(HARDWARE_MOTHERBOARD),999)
# Mega controller
else ifeq ($(HARDWARE_MOTHERBOARD),310)
# abee Scoovo X9H
else ifeq ($(HARDWARE_MOTHERBOARD),321)
# Geeetech GT2560 Rev. A
else ifeq ($(HARDWARE_MOTHERBOARD),74)
# Geeetech GT2560 Rev. A+ (with auto level probe)
else ifeq ($(HARDWARE_MOTHERBOARD),75)
#
# ATmega1281, ATmega2561
#
else ifeq ($(HARDWARE_MOTHERBOARD),702)
MCU ?= atmega1281
else ifeq ($(HARDWARE_MOTHERBOARD),25)
MCU ?= atmega1281
#
# Sanguinololu and Derivatives - ATmega644P, ATmega1284P
#
# Sanguinololu < 1.2
else ifeq ($(HARDWARE_MOTHERBOARD),6)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega644p
# Sanguinololu 1.2 and above
else ifeq ($(HARDWARE_MOTHERBOARD),62)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega644p
# Melzi
else ifeq ($(HARDWARE_MOTHERBOARD),63)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega644p
# Melzi with ATmega1284 (MaKr3d version)
else ifeq ($(HARDWARE_MOTHERBOARD),66)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega1284p
# Melzi Creality3D board (for CR-10 etc)
else ifeq ($(HARDWARE_MOTHERBOARD),89)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega1284p
# Melzi Malyan M150 board
else ifeq ($(HARDWARE_MOTHERBOARD),92)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega1284p
# Tronxy X5S
else ifeq ($(HARDWARE_MOTHERBOARD),505)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega1284p
# STB V1.1
else ifeq ($(HARDWARE_MOTHERBOARD),64)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega1284p
# Azteeg X1
else ifeq ($(HARDWARE_MOTHERBOARD),65)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega1284p
# Anet 1.0 (Melzi clone)
else ifeq ($(HARDWARE_MOTHERBOARD),69)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega1284p
#
# Other ATmega644P, ATmega644, ATmega1284P
#
# Gen3 Monolithic Electronics
else ifeq ($(HARDWARE_MOTHERBOARD),22)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega644p
# Gen3+
else ifeq ($(HARDWARE_MOTHERBOARD),9)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega644p
# Gen6
else ifeq ($(HARDWARE_MOTHERBOARD),5)
HARDWARE_VARIANT ?= Gen6
MCU ?= atmega644p
# Gen6 deluxe
else ifeq ($(HARDWARE_MOTHERBOARD),51)
HARDWARE_VARIANT ?= Gen6
MCU ?= atmega644p
# Gen7 custom (Alfons3 Version)
else ifeq ($(HARDWARE_MOTHERBOARD),10)
HARDWARE_VARIANT ?= Gen7
MCU ?= atmega644
F_CPU ?= 20000000
else ifeq ($(HARDWARE_MOTHERBOARD),11)
# Gen7 v1.1, v1.2
else ifeq ($(HARDWARE_MOTHERBOARD),11)
HARDWARE_VARIANT ?= Gen7
MCU ?= atmega644p
F_CPU ?= 20000000
else ifeq ($(HARDWARE_MOTHERBOARD),12)
# Gen7 v1.3
else ifeq ($(HARDWARE_MOTHERBOARD),12)
HARDWARE_VARIANT ?= Gen7
MCU ?= atmega644p
F_CPU ?= 20000000
else ifeq ($(HARDWARE_MOTHERBOARD),13)
# Gen7 v1.4
else ifeq ($(HARDWARE_MOTHERBOARD),13)
HARDWARE_VARIANT ?= Gen7
MCU ?= atmega1284p
F_CPU ?= 20000000
#RAMPS
else ifeq ($(HARDWARE_MOTHERBOARD),3)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),33)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),34)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),35)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),36)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),38)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),43)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),44)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),45)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),46)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),48)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
#RAMPS equivalents
else ifeq ($(HARDWARE_MOTHERBOARD),143)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),144)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),145)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),146)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),148)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),77)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),78)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),79)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),401)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),402)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),40)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),41)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),47)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),53)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),504)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),37)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),42)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),52)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),49)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),72)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),80)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),503)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),431)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),343)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),243)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
#Other ATmega1280, ATmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),111)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),112)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),2)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),21)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),200)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),70)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),701)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),703)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),704)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),302)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),303)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),304)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),305)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),21)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),999)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),310)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),321)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),74)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),75)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
#Gen6
else ifeq ($(HARDWARE_MOTHERBOARD),5)
HARDWARE_VARIANT ?= Gen6
MCU ?= atmega644p
else ifeq ($(HARDWARE_MOTHERBOARD),51)
HARDWARE_VARIANT ?= Gen6
MCU ?= atmega644p
#Sanguinololu
else ifeq ($(HARDWARE_MOTHERBOARD),6)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega644p
else ifeq ($(HARDWARE_MOTHERBOARD),62)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega644p
else ifeq ($(HARDWARE_MOTHERBOARD),63)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega644p
else ifeq ($(HARDWARE_MOTHERBOARD),64)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega1284p
else ifeq ($(HARDWARE_MOTHERBOARD),65)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega1284p
else ifeq ($(HARDWARE_MOTHERBOARD),66)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega1284p
else ifeq ($(HARDWARE_MOTHERBOARD),69)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega1284p
else ifeq ($(HARDWARE_MOTHERBOARD),89)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega1284p
else ifeq ($(HARDWARE_MOTHERBOARD),92)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega1284p
else ifeq ($(HARDWARE_MOTHERBOARD),505)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega1284p
else ifeq ($(HARDWARE_MOTHERBOARD),601)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega1284p
#Ultimaker
else ifeq ($(HARDWARE_MOTHERBOARD),7)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),71)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega1280
#ATmega1281, ATmega2561
else ifeq ($(HARDWARE_MOTHERBOARD),702)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega1281
else ifeq ($(HARDWARE_MOTHERBOARD),25)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega1281
#Teensylu
else ifeq ($(HARDWARE_MOTHERBOARD),8)
HARDWARE_VARIANT ?= Teensy
MCU ?= at90usb1286
else ifeq ($(HARDWARE_MOTHERBOARD),81)
HARDWARE_VARIANT ?= Teensy
MCU ?= at90usb1286
else ifeq ($(HARDWARE_MOTHERBOARD),811)
HARDWARE_VARIANT ?= Teensy
MCU ?= at90usb1286
else ifeq ($(HARDWARE_MOTHERBOARD),82)
HARDWARE_VARIANT ?= Teensy
MCU ?= at90usb646
else ifeq ($(HARDWARE_MOTHERBOARD),83)
HARDWARE_VARIANT ?= Teensy
MCU ?= at90usb1286
else ifeq ($(HARDWARE_MOTHERBOARD),84)
HARDWARE_VARIANT ?= Teensy
MCU ?= at90usb1286
else ifeq ($(HARDWARE_MOTHERBOARD),88)
HARDWARE_VARIANT ?= Teensy
MCU ?= at90usb1286
#Gen3+
else ifeq ($(HARDWARE_MOTHERBOARD),9)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega644p
#Gen3 Monolithic Electronics
else ifeq ($(HARDWARE_MOTHERBOARD),22)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega644p
#Megatronics
else ifeq ($(HARDWARE_MOTHERBOARD),70)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
#Alpha OMCA board
else ifeq ($(HARDWARE_MOTHERBOARD),90)
# Alpha OMCA board
else ifeq ($(HARDWARE_MOTHERBOARD),90)
HARDWARE_VARIANT ?= SanguinoA
MCU ?= atmega644
#Final OMCA board
else ifeq ($(HARDWARE_MOTHERBOARD),91)
# Final OMCA board
else ifeq ($(HARDWARE_MOTHERBOARD),91)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega644p
# Sethi 3D_1
else ifeq ($(HARDWARE_MOTHERBOARD),20)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega644p
#Sethi 3D_1
else ifeq ($(HARDWARE_MOTHERBOARD),20)
HARDWARE_VARIANT ?= Sanguino
MCU ?= atmega644p
#
# Teensyduino - AT90USB1286, AT90USB1286P
#
#Rambo
else ifeq ($(HARDWARE_MOTHERBOARD),301)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
#Azteeg
else ifeq ($(HARDWARE_MOTHERBOARD),67)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
else ifeq ($(HARDWARE_MOTHERBOARD),68)
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
# Teensylu
else ifeq ($(HARDWARE_MOTHERBOARD),8)
HARDWARE_VARIANT ?= Teensy
MCU ?= at90usb1286
# Printrboard (AT90USB1286)
else ifeq ($(HARDWARE_MOTHERBOARD),81)
HARDWARE_VARIANT ?= Teensy
MCU ?= at90usb1286
# Printrboard Revision F (AT90USB1286)
else ifeq ($(HARDWARE_MOTHERBOARD),811)
HARDWARE_VARIANT ?= Teensy
MCU ?= at90usb1286
# Brainwave (AT90USB646)
else ifeq ($(HARDWARE_MOTHERBOARD),82)
HARDWARE_VARIANT ?= Teensy
MCU ?= at90usb646
# Brainwave Pro (AT90USB1286)
else ifeq ($(HARDWARE_MOTHERBOARD),83)
HARDWARE_VARIANT ?= Teensy
MCU ?= at90usb1286
# SAV Mk-I (AT90USB1286)
else ifeq ($(HARDWARE_MOTHERBOARD),84)
HARDWARE_VARIANT ?= Teensy
MCU ?= at90usb1286
# Teensy++2.0 (AT90USB1286) - CLI compile: HARDWARE_MOTHERBOARD=84 make
else ifeq ($(HARDWARE_MOTHERBOARD),85)
HARDWARE_VARIANT ?= Teensy
MCU ?= at90usb1286
# 5DPrint D8 Driver Board
else ifeq ($(HARDWARE_MOTHERBOARD),88)
HARDWARE_VARIANT ?= Teensy
MCU ?= at90usb1286
endif
@@ -417,6 +394,10 @@ endif
# Set to 16Mhz if not yet set.
F_CPU ?= 16000000
# Set to arduino, ATmega2560 if not yet set.
HARDWARE_VARIANT ?= arduino
MCU ?= atmega2560
# Arduino contained the main source code for the Arduino
# Libraries, the "hardware variant" are for boards
# that derives from that, and their source are present in
Marlin/Marlin.h
+7 -3
View File
@@ -197,13 +197,17 @@ bool enqueue_and_echo_command(const char* cmd, bool say_ok=false); // Add a sing
void enqueue_and_echo_commands_P(const char * const cmd); // Set one or more commands to be prioritized over the next Serial/SD command.
void clear_command_queue();
#define HAS_LCD_QUEUE_NOW (ENABLED(ULTIPANEL) && (ENABLED(AUTO_BED_LEVELING_UBL) || ENABLED(PID_AUTOTUNE_MENU) || ENABLED(ADVANCED_PAUSE_FEATURE)))
#if ENABLED(M100_FREE_MEMORY_WATCHER) || ENABLED(POWER_LOSS_RECOVERY)
extern char command_queue[BUFSIZE][MAX_CMD_SIZE];
#endif
#define HAS_LCD_QUEUE_NOW (ENABLED(MALYAN_LCD) || (ENABLED(ULTIPANEL) && (ENABLED(AUTO_BED_LEVELING_UBL) || ENABLED(PID_AUTOTUNE_MENU) || ENABLED(ADVANCED_PAUSE_FEATURE))))
#define HAS_QUEUE_NOW (ENABLED(SDSUPPORT) || HAS_LCD_QUEUE_NOW)
#if HAS_QUEUE_NOW
// Return only when commands are actually enqueued
void enqueue_and_echo_command_now(const char* cmd, bool say_ok=false);
void enqueue_and_echo_command_now(const char* cmd);
#if HAS_LCD_QUEUE_NOW
void enqueue_and_echo_commands_P_now(const char * const cmd);
void enqueue_and_echo_commands_now_P(const char * const cmd);
#endif
#endif
Marlin/Marlin_main.cpp
+161 -67
View File
@@ -288,6 +288,10 @@
#include "fwretract.h"
#endif
#if ENABLED(POWER_LOSS_RECOVERY)
#include "power_loss_recovery.h"
#endif
#if ENABLED(FILAMENT_RUNOUT_SENSOR)
#include "runout.h"
#endif
@@ -415,14 +419,11 @@ static long gcode_N, gcode_LastN, Stopped_gcode_LastN = 0;
* the main loop. The process_next_command function parses the next
* command and hands off execution to individual handler functions.
*/
uint8_t commands_in_queue = 0; // Count of commands in the queue
static uint8_t cmd_queue_index_r = 0, // Ring buffer read position
cmd_queue_index_w = 0; // Ring buffer write position
#if ENABLED(M100_FREE_MEMORY_WATCHER)
char command_queue[BUFSIZE][MAX_CMD_SIZE]; // Necessary so M100 Free Memory Dumper can show us the commands and any corruption
#else // This can be collapsed back to the way it was soon.
static char command_queue[BUFSIZE][MAX_CMD_SIZE];
#endif
uint8_t commands_in_queue = 0, // Count of commands in the queue
cmd_queue_index_r = 0, // Ring buffer read (out) position
cmd_queue_index_w = 0; // Ring buffer write (in) position
char command_queue[BUFSIZE][MAX_CMD_SIZE];
/**
* Next Injected Command pointer. NULL if no commands are being injected.
@@ -571,6 +572,10 @@ uint8_t target_extruder;
#define ADJUST_DELTA(V) NOOP
#endif
#if HAS_HEATED_BED && ENABLED(WAIT_FOR_BED_HEATER)
const static char msg_wait_for_bed_heating[] PROGMEM = "Wait for bed heating...\n";
#endif
// Extruder offsets
#if HOTENDS > 1
float hotend_offset[XYZ][HOTENDS]; // Initialized by settings.load()
@@ -586,13 +591,13 @@ uint8_t target_extruder;
#endif
#if HAS_POWER_SWITCH
bool powersupply_on =
bool powersupply_on = (
#if ENABLED(PS_DEFAULT_OFF)
false
#else
true
#endif
;
);
#if ENABLED(AUTO_POWER_CONTROL)
#define PSU_ON() powerManager.power_on()
#define PSU_OFF() powerManager.power_off()
@@ -897,11 +902,11 @@ bool enqueue_and_echo_command(const char* cmd, bool say_ok/*=false*/) {
}
#if HAS_QUEUE_NOW
void enqueue_and_echo_command_now(const char* cmd, bool say_ok/*=false*/) {
while (!enqueue_and_echo_command(cmd, say_ok)) idle();
void enqueue_and_echo_command_now(const char* cmd) {
while (!enqueue_and_echo_command(cmd)) idle();
}
#if HAS_LCD_QUEUE_NOW
void enqueue_and_echo_commands_P_now(const char * const pgcode) {
void enqueue_and_echo_commands_now_P(const char * const pgcode) {
enqueue_and_echo_commands_P(pgcode);
while (drain_injected_commands_P()) idle();
}
@@ -1227,21 +1232,43 @@ inline void get_serial_commands() {
}
}
#if ENABLED(POWER_LOSS_RECOVERY)
inline bool drain_job_recovery_commands() {
static uint8_t job_recovery_commands_index = 0; // Resets on reboot
if (job_recovery_commands_count) {
if (_enqueuecommand(job_recovery_commands[job_recovery_commands_index])) {
++job_recovery_commands_index;
if (!--job_recovery_commands_count) job_recovery_phase = JOB_RECOVERY_IDLE;
}
return true;
}
return false;
}
#endif
#endif // SDSUPPORT
/**
* Add to the circular command queue the next command from:
* - The command-injection queue (injected_commands_P)
* - The active serial input (usually USB)
* - Commands left in the queue after power-loss
* - The SD card file being actively printed
*/
void get_available_commands() {
// if any immediate commands remain, don't get other commands yet
// Immediate commands block the other queues
if (drain_injected_commands_P()) return;
get_serial_commands();
#if ENABLED(POWER_LOSS_RECOVERY)
// Commands for power-loss recovery take precedence
if (job_recovery_phase == JOB_RECOVERY_YES && drain_job_recovery_commands()) return;
#endif
#if ENABLED(SDSUPPORT)
get_sdcard_commands();
#endif
@@ -2186,6 +2213,16 @@ void clean_up_after_endstop_or_probe_move() {
if (DEBUGGING(LEVELING)) DEBUG_POS(">>> do_probe_move", current_position);
#endif
#if HAS_HEATED_BED && ENABLED(WAIT_FOR_BED_HEATER)
// Wait for bed to heat back up between probing points
if (thermalManager.isHeatingBed()) {
serialprintPGM(msg_wait_for_bed_heating);
LCD_MESSAGEPGM(MSG_BED_HEATING);
while (thermalManager.isHeatingBed()) safe_delay(200);
lcd_reset_status();
}
#endif
// Deploy BLTouch at the start of any probe
#if ENABLED(BLTOUCH)
if (set_bltouch_deployed(true)) return true;
@@ -2461,7 +2498,21 @@ void clean_up_after_endstop_or_probe_move() {
planner.unapply_leveling(current_position);
}
#else
planner.leveling_active = enable; // just flip the bit, current_position will be wrong until next move.
// UBL equivalents for apply/unapply_leveling
#if ENABLED(SKEW_CORRECTION)
float pos[XYZ] = { current_position[X_AXIS], current_position[Y_AXIS], current_position[Z_AXIS] };
planner.skew(pos[X_AXIS], pos[Y_AXIS], pos[Z_AXIS]);
#else
const float (&pos)[XYZE] = current_position;
#endif
if (planner.leveling_active) {
current_position[Z_AXIS] += ubl.get_z_correction(pos[X_AXIS], pos[Y_AXIS]);
planner.leveling_active = false;
}
else {
planner.leveling_active = true;
current_position[Z_AXIS] -= ubl.get_z_correction(pos[X_AXIS], pos[Y_AXIS]);
}
#endif
#else // ABL
@@ -2885,6 +2936,16 @@ static void do_homing_move(const AxisEnum axis, const float distance, const floa
SERIAL_EOL();
}
#endif
#if HOMING_Z_WITH_PROBE && HAS_HEATED_BED && ENABLED(WAIT_FOR_BED_HEATER)
// Wait for bed to heat back up between probing points
if (axis == Z_AXIS && distance < 0 && thermalManager.isHeatingBed()) {
serialprintPGM(msg_wait_for_bed_heating);
LCD_MESSAGEPGM(MSG_BED_HEATING);
while (thermalManager.isHeatingBed()) safe_delay(200);
lcd_reset_status();
}
#endif
// Only do some things when moving towards an endstop
const int8_t axis_home_dir =
@@ -3956,6 +4017,8 @@ inline void gcode_G4() {
* None Home to all axes with no parameters.
* With QUICK_HOME enabled XY will home together, then Z.
*
* Rn Raise by n mm/inches before homing
*
* Cartesian parameters
*
* X Home to the X endstop
@@ -4030,11 +4093,12 @@ inline void gcode_G28(const bool always_home_all) {
#endif
#if ENABLED(UNKNOWN_Z_NO_RAISE)
const float z_homing_height = axis_known_position[Z_AXIS] ? Z_HOMING_HEIGHT : 0;
#else
constexpr float z_homing_height = Z_HOMING_HEIGHT;
#endif
const float z_homing_height = (
#if ENABLED(UNKNOWN_Z_NO_RAISE)
!axis_known_position[Z_AXIS] ? 0 :
#endif
(parser.seenval('R') ? parser.value_linear_units() : Z_HOMING_HEIGHT)
);
if (z_homing_height && (home_all || homeX || homeY)) {
// Raise Z before homing any other axes and z is not already high enough (never lower z)
@@ -4223,7 +4287,7 @@ void home_all_axes() { gcode_G28(true); }
static bool enable_soft_endstops;
#endif
const MeshLevelingState state = (MeshLevelingState)parser.byteval('S', (int8_t)MeshReport);
MeshLevelingState state = (MeshLevelingState)parser.byteval('S', (int8_t)MeshReport);
if (!WITHIN(state, 0, 5)) {
SERIAL_PROTOCOLLNPGM("S out of range (0-5).");
return;
@@ -4244,8 +4308,11 @@ void home_all_axes() { gcode_G28(true); }
case MeshStart:
mbl.reset();
mbl_probe_index = 0;
enqueue_and_echo_commands_P(lcd_wait_for_move ? PSTR("G29 S2") : PSTR("G28\nG29 S2"));
break;
if (!lcd_wait_for_move) {
enqueue_and_echo_commands_P(PSTR("G28\nG29 S2"));
return;
}
state = MeshNext;
case MeshNext:
if (mbl_probe_index < 0) {
@@ -4259,10 +4326,10 @@ void home_all_axes() { gcode_G28(true); }
enable_soft_endstops = soft_endstops_enabled;
#endif
// Move close to the bed before the first point
do_blocking_move_to_z(Z_MIN_POS);
do_blocking_move_to_z(0);
}
else {
// For G29 S2 after adjusting Z.
// Save Z for the previous mesh position
mbl.set_zigzag_z(mbl_probe_index - 1, current_position[Z_AXIS]);
#if HAS_SOFTWARE_ENDSTOPS
soft_endstops_enabled = enable_soft_endstops;
@@ -4281,7 +4348,7 @@ void home_all_axes() { gcode_G28(true); }
}
else {
// One last "return to the bed" (as originally coded) at completion
current_position[Z_AXIS] = Z_MIN_POS + MANUAL_PROBE_HEIGHT;
current_position[Z_AXIS] = MANUAL_PROBE_HEIGHT;
buffer_line_to_current_position();
stepper.synchronize();
@@ -4295,7 +4362,7 @@ void home_all_axes() { gcode_G28(true); }
set_bed_leveling_enabled(true);
#if ENABLED(MESH_G28_REST_ORIGIN)
current_position[Z_AXIS] = Z_MIN_POS;
current_position[Z_AXIS] = 0;
set_destination_from_current();
buffer_line_to_destination(homing_feedrate(Z_AXIS));
stepper.synchronize();
@@ -4355,7 +4422,7 @@ void home_all_axes() { gcode_G28(true); }
} // switch(state)
if (state == MeshStart || state == MeshNext) {
if (state == MeshNext) {
SERIAL_PROTOCOLPAIR("MBL G29 point ", min(mbl_probe_index, GRID_MAX_POINTS));
SERIAL_PROTOCOLLNPAIR(" of ", int(GRID_MAX_POINTS));
}
@@ -4794,7 +4861,7 @@ void home_all_axes() { gcode_G28(true); }
enable_soft_endstops = soft_endstops_enabled;
#endif
// Move close to the bed before the first point
do_blocking_move_to_z(Z_MIN_POS);
do_blocking_move_to_z(0);
}
else {
@@ -5786,7 +5853,7 @@ void home_all_axes() { gcode_G28(true); }
_opposite_results = (_4p_calibration && !towers_set) || probe_points >= 3,
_endstop_results = probe_points != 1 && probe_points != -1 && probe_points != 0,
_angle_results = probe_points >= 3 && towers_set;
const static char save_message[] PROGMEM = "Save with M500 and/or copy to Configuration.h";
static const char save_message[] PROGMEM = "Save with M500 and/or copy to Configuration.h";
int8_t iterations = 0;
float test_precision,
zero_std_dev = (verbose_level ? 999.0 : 0.0), // 0.0 in dry-run mode : forced end
@@ -6298,12 +6365,9 @@ inline void gcode_G92() {
ms += millis(); // wait until this time for a click
while (PENDING(millis(), ms) && wait_for_user) idle();
}
else {
#if ENABLED(ULTIPANEL)
if (lcd_detected())
#endif
while (wait_for_user) idle();
}
else
while (wait_for_user) idle();
#if ENABLED(PRINTER_EVENT_LEDS) && ENABLED(SDSUPPORT)
if (lights_off_after_print) {
@@ -6312,11 +6376,7 @@ inline void gcode_G92() {
}
#endif
#if ENABLED(ULTIPANEL)
if (lcd_detected()) {
print_job_timer.isPaused() ? LCD_MESSAGEPGM(WELCOME_MSG) : LCD_MESSAGEPGM(MSG_RESUMING);
}
#endif
lcd_reset_status();
wait_for_user = false;
KEEPALIVE_STATE(IN_HANDLER);
@@ -6973,6 +7033,10 @@ inline void gcode_M17() {
* M24: Start or Resume SD Print
*/
inline void gcode_M24() {
#if ENABLED(POWER_LOSS_RECOVERY)
card.removeJobRecoveryFile();
#endif
#if ENABLED(PARK_HEAD_ON_PAUSE)
resume_print();
#endif
@@ -7827,7 +7891,7 @@ inline void gcode_M105() {
#if HAS_TEMP_SENSOR
SERIAL_PROTOCOLPGM(MSG_OK);
thermalManager.print_heaterstates();
#else // !HAS_TEMP_HOTEND && !HAS_TEMP_BED
#else // !HAS_TEMP_SENSOR
SERIAL_ERROR_START();
SERIAL_ERRORLNPGM(MSG_ERR_NO_THERMISTORS);
#endif
@@ -8080,7 +8144,7 @@ inline void gcode_M109() {
} while (wait_for_heatup && TEMP_CONDITIONS);
if (wait_for_heatup) {
lcd_setstatusPGM(wants_to_cool ? PSTR(MSG_COOLING_COMPLETE) : PSTR(MSG_HEATING_COMPLETE));
lcd_reset_status();
#if ENABLED(PRINTER_EVENT_LEDS)
leds.set_white();
#endif
@@ -8091,7 +8155,15 @@ inline void gcode_M109() {
#endif
}
#if HAS_TEMP_BED
#if HAS_HEATED_BED
/**
* M140: Set bed temperature
*/
inline void gcode_M140() {
if (DEBUGGING(DRYRUN)) return;
if (parser.seenval('S')) thermalManager.setTargetBed(parser.value_celsius());
}
#ifndef MIN_COOLING_SLOPE_DEG_BED
#define MIN_COOLING_SLOPE_DEG_BED 1.50
@@ -8217,13 +8289,13 @@ inline void gcode_M109() {
} while (wait_for_heatup && TEMP_BED_CONDITIONS);
if (wait_for_heatup) LCD_MESSAGEPGM(MSG_BED_DONE);
if (wait_for_heatup) lcd_reset_status();
#if DISABLED(BUSY_WHILE_HEATING)
KEEPALIVE_STATE(IN_HANDLER);
#endif
}
#endif // HAS_TEMP_BED
#endif // HAS_HEATED_BED
/**
* M110: Set Current Line Number
@@ -8238,7 +8310,7 @@ inline void gcode_M110() {
inline void gcode_M111() {
if (parser.seen('S')) marlin_debug_flags = parser.byteval('S');
const static char str_debug_1[] PROGMEM = MSG_DEBUG_ECHO,
static const char str_debug_1[] PROGMEM = MSG_DEBUG_ECHO,
str_debug_2[] PROGMEM = MSG_DEBUG_INFO,
str_debug_4[] PROGMEM = MSG_DEBUG_ERRORS,
str_debug_8[] PROGMEM = MSG_DEBUG_DRYRUN,
@@ -8248,7 +8320,7 @@ inline void gcode_M111() {
#endif
;
const static char* const debug_strings[] PROGMEM = {
static const char* const debug_strings[] PROGMEM = {
str_debug_1, str_debug_2, str_debug_4, str_debug_8, str_debug_16
#if ENABLED(DEBUG_LEVELING_FEATURE)
, str_debug_32
@@ -8318,14 +8390,6 @@ inline void gcode_M111() {
#endif // BARICUDA
/**
* M140: Set bed temperature
*/
inline void gcode_M140() {
if (DEBUGGING(DRYRUN)) return;
if (parser.seenval('S')) thermalManager.setTargetBed(parser.value_celsius());
}
#if ENABLED(ULTIPANEL)
/**
@@ -8766,13 +8830,25 @@ inline void gcode_M115() {
#endif
);
// THERMAL_PROTECTION
cap_line(PSTR("THERMAL_PROTECTION")
#if ENABLED(THERMAL_PROTECTION_HOTENDS) && ENABLED(THERMAL_PROTECTION_BED)
, true
#endif
);
#endif // EXTENDED_CAPABILITIES_REPORT
}
/**
* M117: Set LCD Status Message
*/
inline void gcode_M117() { lcd_setstatus(parser.string_arg); }
inline void gcode_M117() {
if (parser.string_arg[0])
lcd_setstatus(parser.string_arg);
else
lcd_reset_status();
}
/**
* M118: Display a message in the host console.
@@ -9327,6 +9403,14 @@ inline void gcode_M221() {
planner.flow_percentage[target_extruder] = parser.value_int();
planner.refresh_e_factor(target_extruder);
}
else {
SERIAL_ECHO_START();
SERIAL_CHAR('E');
SERIAL_CHAR('0' + target_extruder);
SERIAL_ECHOPAIR(" Flow: ", planner.flow_percentage[target_extruder]);
SERIAL_CHAR('%');
SERIAL_EOL();
}
}
/**
@@ -9904,6 +9988,7 @@ void quickstop_stepper() {
* With AUTO_BED_LEVELING_UBL only:
*
* L[index] Load UBL mesh from index (0 is default)
* T[map] 0:Human-readable 1:CSV 2:"LCD" 4:Compact
*/
inline void gcode_M420() {
@@ -9942,7 +10027,7 @@ void quickstop_stepper() {
// L to load a mesh from the EEPROM
if (parser.seen('L') || parser.seen('V')) {
ubl.display_map(0); // Currently only supports one map type
ubl.display_map(parser.byteval('T')); // 0=
SERIAL_ECHOLNPAIR("ubl.mesh_is_valid = ", ubl.mesh_is_valid());
SERIAL_ECHOLNPAIR("ubl.storage_slot = ", ubl.storage_slot);
}
@@ -10073,6 +10158,7 @@ void quickstop_stepper() {
* Usage:
* M421 I<xindex> J<yindex> Z<linear>
* M421 I<xindex> J<yindex> Q<offset>
* M421 I<xindex> J<yindex> N
* M421 C Z<linear>
* M421 C Q<offset>
*/
@@ -10081,6 +10167,7 @@ void quickstop_stepper() {
const bool hasI = ix >= 0,
hasJ = iy >= 0,
hasC = parser.seen('C'),
hasN = parser.seen('N'),
hasZ = parser.seen('Z'),
hasQ = !hasZ && parser.seen('Q');
@@ -10090,7 +10177,7 @@ void quickstop_stepper() {
iy = location.y_index;
}
if (int(hasC) + int(hasI && hasJ) != 1 || !(hasZ || hasQ)) {
if (int(hasC) + int(hasI && hasJ) != 1 || !(hasZ || hasQ || hasN)) {
SERIAL_ERROR_START();
SERIAL_ERRORLNPGM(MSG_ERR_M421_PARAMETERS);
}
@@ -10099,7 +10186,7 @@ void quickstop_stepper() {
SERIAL_ERRORLNPGM(MSG_ERR_MESH_XY);
}
else
ubl.z_values[ix][iy] = parser.value_linear_units() + (hasQ ? ubl.z_values[ix][iy] : 0);
ubl.z_values[ix][iy] = hasN ? NAN : parser.value_linear_units() + (hasQ ? ubl.z_values[ix][iy] : 0);
}
#endif // AUTO_BED_LEVELING_UBL
@@ -10541,7 +10628,7 @@ inline void gcode_M502() {
// Restore Z axis
if (park_point.z > 0)
do_blocking_move_to_z(max(current_position[Z_AXIS] - park_point.z, Z_MIN_POS), NOZZLE_PARK_Z_FEEDRATE);
do_blocking_move_to_z(max(current_position[Z_AXIS] - park_point.z, 0), NOZZLE_PARK_Z_FEEDRATE);
#if EXTRUDERS > 1
// Restore toolhead if it was changed
@@ -10614,7 +10701,7 @@ inline void gcode_M502() {
// Restore Z axis
if (park_point.z > 0)
do_blocking_move_to_z(max(current_position[Z_AXIS] - park_point.z, Z_MIN_POS), NOZZLE_PARK_Z_FEEDRATE);
do_blocking_move_to_z(max(current_position[Z_AXIS] - park_point.z, 0), NOZZLE_PARK_Z_FEEDRATE);
#if EXTRUDERS > 1
// Restore toolhead if it was changed
@@ -11978,8 +12065,6 @@ void process_parsed_command() {
case 113: gcode_M113(); break; // M113: Set Host Keepalive Interval
#endif
case 140: gcode_M140(); break; // M140: Set Bed Temperature
case 105: gcode_M105(); KEEPALIVE_STATE(NOT_BUSY); return; // M105: Report Temperatures (and say "ok")
#if ENABLED(AUTO_REPORT_TEMPERATURES)
@@ -11988,7 +12073,8 @@ void process_parsed_command() {
case 109: gcode_M109(); break; // M109: Set Hotend Temperature. Wait for target.
#if HAS_TEMP_BED
#if HAS_HEATED_BED
case 140: gcode_M140(); break; // M140: Set Bed Temperature
case 190: gcode_M190(); break; // M190: Set Bed Temperature. Wait for target.
#endif
@@ -13601,7 +13687,7 @@ void prepare_move_to_destination() {
if (ELAPSED(millis(), next_status_led_update_ms)) {
next_status_led_update_ms += 500; // Update every 0.5s
float max_temp = 0.0;
#if HAS_TEMP_BED
#if HAS_HEATED_BED
max_temp = MAX3(max_temp, thermalManager.degTargetBed(), thermalManager.degBed());
#endif
HOTEND_LOOP()
@@ -14212,6 +14298,10 @@ void setup() {
#endif
#endif
#if ENABLED(POWER_LOSS_RECOVERY)
do_print_job_recovery();
#endif
#if ENABLED(USE_WATCHDOG)
watchdog_init();
#endif
@@ -14289,8 +14379,12 @@ void loop() {
ok_to_send();
}
}
else
else {
process_next_command();
#if ENABLED(POWER_LOSS_RECOVERY)
if (card.cardOK && card.sdprinting) save_job_recovery_info();
#endif
}
#else
Marlin/SanityCheck.h
+27 -9
View File
@@ -270,6 +270,16 @@
#error "AUTOMATIC_CURRENT_CONTROL is now MONITOR_DRIVER_STATUS. Please update your configuration."
#elif defined(FILAMENT_CHANGE_LOAD_LENGTH)
#error "FILAMENT_CHANGE_LOAD_LENGTH is now FILAMENT_CHANGE_FAST_LOAD_LENGTH. Please update your configuration."
#elif ENABLED(LEVEL_BED_CORNERS) && !defined(LEVEL_CORNERS_INSET)
#error "LEVEL_BED_CORNERS requires a LEVEL_CORNERS_INSET value. Please update your Configuration.h."
#endif
#define BOARD_MKS_13 -47
#define BOARD_TRIGORILLA -343
#if MB(MKS_13)
#error "BOARD_MKS_13 has been renamed BOARD_MKS_GEN_13. Please update your configuration."
#elif MB(BOARD_TRIGORILLA)
#error "BOARD_TRIGORILLA has been renamed BOARD_TRIGORILLA_13. Please update your configuration."
#endif
/**
@@ -427,7 +437,7 @@ static_assert(X_MAX_LENGTH >= X_BED_SIZE && Y_MAX_LENGTH >= Y_BED_SIZE,
#elif ENABLED(BABYSTEP_ZPROBE_OFFSET) && !HAS_BED_PROBE
#error "BABYSTEP_ZPROBE_OFFSET requires a probe."
#elif ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY) && !ENABLED(DOGLCD)
#error "BABYSTEP_ZPROBE_GFX_OVERLAY requires a DOGLCD."
#error "BABYSTEP_ZPROBE_GFX_OVERLAY requires a Graphical LCD."
#elif ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY) && !ENABLED(BABYSTEP_ZPROBE_OFFSET)
#error "BABYSTEP_ZPROBE_GFX_OVERLAY requires a BABYSTEP_ZPROBE_OFFSET."
#endif
@@ -1448,14 +1458,18 @@ static_assert(X_MAX_LENGTH >= X_BED_SIZE && Y_MAX_LENGTH >= Y_BED_SIZE,
// clearing the stallGuard activated status is found.
#if ENABLED(DELTA) && !ENABLED(STEALTHCHOP)
#error "SENSORLESS_HOMING on DELTA currently requires STEALTHCHOP."
#elif X_HOME_DIR == -1 && DISABLED(X_MIN_ENDSTOP_INVERTING)
#error "SENSORLESS_HOMING requires X_MIN_ENDSTOP_INVERTING when homing to X_MIN."
#elif X_HOME_DIR == 1 && DISABLED(X_MAX_ENDSTOP_INVERTING)
#error "SENSORLESS_HOMING requires X_MAX_ENDSTOP_INVERTING when homing to X_MAX."
#elif Y_HOME_DIR == -1 && DISABLED(Y_MIN_ENDSTOP_INVERTING)
#error "SENSORLESS_HOMING requires Y_MIN_ENDSTOP_INVERTING when homing to Y_MIN."
#elif Y_HOME_DIR == 1 && DISABLED(Y_MAX_ENDSTOP_INVERTING)
#error "SENSORLESS_HOMING requires Y_MAX_ENDSTOP_INVERTING when homing to Y_MAX."
#elif X_SENSORLESS && X_HOME_DIR == -1 && (DISABLED(X_MIN_ENDSTOP_INVERTING) || DISABLED(ENDSTOPPULLUP_XMIN))
#error "SENSORLESS_HOMING requires X_MIN_ENDSTOP_INVERTING and ENDSTOPPULLUP_XMIN when homing to X_MIN."
#elif X_SENSORLESS && X_HOME_DIR == 1 && (DISABLED(X_MAX_ENDSTOP_INVERTING) || DISABLED(ENDSTOPPULLUP_XMAX))
#error "SENSORLESS_HOMING requires X_MAX_ENDSTOP_INVERTING and ENDSTOPPULLUP_XMAX when homing to X_MAX."
#elif Y_SENSORLESS && Y_HOME_DIR == -1 && (DISABLED(Y_MIN_ENDSTOP_INVERTING) || DISABLED(ENDSTOPPULLUP_YMIN))
#error "SENSORLESS_HOMING requires Y_MIN_ENDSTOP_INVERTING and ENDSTOPPULLUP_YMIN when homing to Y_MIN."
#elif Y_SENSORLESS && Y_HOME_DIR == 1 && (DISABLED(Y_MAX_ENDSTOP_INVERTING) || DISABLED(ENDSTOPPULLUP_YMAX))
#error "SENSORLESS_HOMING requires Y_MAX_ENDSTOP_INVERTING and ENDSTOPPULLUP_YMAX when homing to Y_MAX."
#elif Z_SENSORLESS && Z_HOME_DIR == -1 && (DISABLED(Z_MIN_ENDSTOP_INVERTING) || DISABLED(ENDSTOPPULLUP_ZMIN))
#error "SENSORLESS_HOMING requires Z_MIN_ENDSTOP_INVERTING and ENDSTOPPULLUP_ZMIN when homing to Z_MIN."
#elif Z_SENSORLESS && Z_HOME_DIR == 1 && (DISABLED(Z_MAX_ENDSTOP_INVERTING) || DISABLED(ENDSTOPPULLUP_ZMAX))
#error "SENSORLESS_HOMING requires Z_MAX_ENDSTOP_INVERTING and ENDSTOPPULLUP_ZMAX when homing to Z_MAX."
#endif
#endif
@@ -1731,4 +1745,8 @@ static_assert(COUNT(sanity_arr_3) <= XYZE_N, "DEFAULT_MAX_ACCELERATION has too m
#endif
#endif
#if ENABLED(POWER_LOSS_RECOVERY) && !ENABLED(ULTIPANEL)
#error "POWER_LOSS_RECOVERY currently requires an LCD Controller."
#endif
#endif // _SANITYCHECK_H_
Marlin/boards.h
+7 -5
View File
@@ -58,9 +58,10 @@
#define BOARD_K8400 79 // Velleman K8400 Controller (derived from 3Drag Controller)
#define BOARD_BAM_DICE 401 // 2PrintBeta BAM&DICE with STK drivers
#define BOARD_BAM_DICE_DUE 402 // 2PrintBeta BAM&DICE Due with STK drivers
#define BOARD_MKS_BASE 40 // MKS BASE 1.0
#define BOARD_MKS_BASE 40 // MKS BASE v1.0
#define BOARD_MKS_BASE_15 405 // MKS v1.5 with Allegro A4982 stepper drivers
#define BOARD_MKS_BASE_HEROIC 41 // MKS BASE 1.0 with Heroic HR4982 stepper drivers
#define BOARD_MKS_13 47 // MKS v1.3 or 1.4 (maybe higher)
#define BOARD_MKS_GEN_13 47 // MKS GEN v1.3 or 1.4
#define BOARD_MKS_GEN_L 53 // MKS GEN L
#define BOARD_ZRIB_V20 504 // zrib V2.0 control board (Chinese knock off RAMPS replica)
#define BOARD_FELIX2 37 // Felix 2.0+ Electronics Board (RAMPS like)
@@ -75,7 +76,8 @@
#define BOARD_RUMBA 80 // Rumba
#define BOARD_BQ_ZUM_MEGA_3D 503 // bq ZUM Mega 3D
#define BOARD_MAKEBOARD_MINI 431 // MakeBoard Mini v2.1.2 is a control board sold by MicroMake
#define BOARD_TRIGORILLA 343 // TriGorilla Anycubic version 1.3 based on RAMPS EFB
#define BOARD_TRIGORILLA_13 343 // TriGorilla Anycubic version 1.3 based on RAMPS EFB
#define BOARD_TRIGORILLA_14 443 // TriGorilla Anycubic version 1.4 based on RAMPS EFB
#define BOARD_RAMPS_ENDER_4 243 // Creality: Ender-4, CR-8
//
@@ -95,7 +97,7 @@
#define BOARD_MINIRAMBO 302 // Mini-Rambo
#define BOARD_MINIRAMBO_10A 303 // Mini-Rambo 1.0a
#define BOARD_EINSY_RAMBO 304 // Einsy Rambo
#define BOARD_EINSY_RETRO 305 // Einsy Rambo
#define BOARD_EINSY_RETRO 305 // Einsy Retro
#define BOARD_ELEFU_3 21 // Elefu Ra Board (v3)
#define BOARD_LEAPFROG 999 // Leapfrog
#define BOARD_MEGACONTROLLER 310 // Mega controller
@@ -123,6 +125,7 @@
#define BOARD_MELZI_TRONXY 505 // Tronxy X5S
#define BOARD_STB_11 64 // STB V1.1
#define BOARD_AZTEEG_X1 65 // Azteeg X1
#define BOARD_ANET_10 69 // Anet 1.0 (Melzi clone)
//
// Other ATmega644P, ATmega644, ATmega1284P
@@ -139,7 +142,6 @@
#define BOARD_OMCA_A 90 // Alpha OMCA board
#define BOARD_OMCA 91 // Final OMCA board
#define BOARD_SETHI 20 // Sethi 3D_1
#define BOARD_ANET_10 69 // Anet 1.0 (Melzi clone)
//
// Teensyduino - AT90USB1286, AT90USB1286P
Marlin/cardreader.cpp
+56 -2
View File
@@ -31,6 +31,10 @@
#include "language.h"
#include "printcounter.h"
#if ENABLED(POWER_LOSS_RECOVERY)
#include "power_loss_recovery.h"
#endif
#define LONGEST_FILENAME (longFilename[0] ? longFilename : filename)
CardReader::CardReader() {
@@ -420,8 +424,7 @@ void CardReader::openFile(char* name, const bool read, const bool subcall/*=fals
strncpy(subdirname, dirname_start, dirname_end - dirname_start);
subdirname[dirname_end - dirname_start] = '\0';
if (!myDir.open(curDir, subdirname, O_READ)) {
SERIAL_PROTOCOLPGM(MSG_SD_OPEN_FILE_FAIL);
SERIAL_PROTOCOL(subdirname);
SERIAL_PROTOCOLPAIR(MSG_SD_OPEN_FILE_FAIL, subdirname);
SERIAL_PROTOCOLCHAR('.');
return;
}
@@ -928,6 +931,15 @@ void CardReader::printingHasFinished() {
}
else {
sdprinting = false;
#if ENABLED(POWER_LOSS_RECOVERY)
openJobRecoveryFile(false);
job_recovery_info.valid_head = job_recovery_info.valid_foot = 0;
(void)saveJobRecoveryInfo();
closeJobRecoveryFile();
job_recovery_commands_count = 0;
#endif
#if ENABLED(SD_FINISHED_STEPPERRELEASE) && defined(SD_FINISHED_RELEASECOMMAND)
stepper.cleaning_buffer_counter = 1; // The command will fire from the Stepper ISR
#endif
@@ -959,4 +971,46 @@ void CardReader::printingHasFinished() {
}
#endif // AUTO_REPORT_SD_STATUS
#if ENABLED(POWER_LOSS_RECOVERY)
char job_recovery_file_name[4] = "bin";
void CardReader::openJobRecoveryFile(const bool read) {
if (!cardOK) return;
if (jobRecoveryFile.isOpen()) return;
if (!jobRecoveryFile.open(&root, job_recovery_file_name, read ? O_READ : O_CREAT | O_WRITE | O_TRUNC | O_SYNC)) {
SERIAL_PROTOCOLPAIR(MSG_SD_OPEN_FILE_FAIL, job_recovery_file_name);
SERIAL_PROTOCOLCHAR('.');
SERIAL_EOL();
}
else
SERIAL_PROTOCOLLNPAIR(MSG_SD_WRITE_TO_FILE, job_recovery_file_name);
}
void CardReader::closeJobRecoveryFile() { jobRecoveryFile.close(); }
bool CardReader::jobRecoverFileExists() {
return jobRecoveryFile.open(&root, job_recovery_file_name, O_READ);
}
int16_t CardReader::saveJobRecoveryInfo() {
jobRecoveryFile.seekSet(0);
const int16_t ret = jobRecoveryFile.write(&job_recovery_info, sizeof(job_recovery_info));
if (ret == -1) SERIAL_PROTOCOLLNPGM("Power-loss file write failed.");
return ret;
}
int16_t CardReader::loadJobRecoveryInfo() {
return jobRecoveryFile.read(&job_recovery_info, sizeof(job_recovery_info));
}
void CardReader::removeJobRecoveryFile() {
if (jobRecoveryFile.remove(&root, job_recovery_file_name))
SERIAL_PROTOCOLLNPGM("Power-loss file deleted.");
else
SERIAL_PROTOCOLLNPGM("Power-loss file delete failed.");
}
#endif // POWER_LOSS_RECOVERY
#endif // SDSUPPORT
Marlin/cardreader.h
+15 -1
View File
@@ -89,11 +89,21 @@ public:
#endif
#endif
#if ENABLED(POWER_LOSS_RECOVERY)
void openJobRecoveryFile(const bool read);
void closeJobRecoveryFile();
bool jobRecoverFileExists();
int16_t saveJobRecoveryInfo();
int16_t loadJobRecoveryInfo();
void removeJobRecoveryFile();
#endif
FORCE_INLINE void pauseSDPrint() { sdprinting = false; }
FORCE_INLINE bool isFileOpen() { return file.isOpen(); }
FORCE_INLINE bool eof() { return sdpos >= filesize; }
FORCE_INLINE int16_t get() { sdpos = file.curPosition(); return (int16_t)file.read(); }
FORCE_INLINE void setIndex(long index) { sdpos = index; file.seekSet(index); }
FORCE_INLINE void setIndex(const uint32_t index) { sdpos = index; file.seekSet(index); }
FORCE_INLINE uint32_t getIndex() { return sdpos; }
FORCE_INLINE uint8_t percentDone() { return (isFileOpen() && filesize) ? sdpos / ((filesize + 99) / 100) : 0; }
FORCE_INLINE char* getWorkDirName() { workDir.getFilename(filename); return filename; }
@@ -168,6 +178,10 @@ private:
SdVolume volume;
SdFile file;
#if ENABLED(POWER_LOSS_RECOVERY)
SdFile jobRecoveryFile;
#endif
#define SD_PROCEDURE_DEPTH 1
#define MAXPATHNAMELENGTH (FILENAME_LENGTH*MAX_DIR_DEPTH + MAX_DIR_DEPTH + 1)
uint8_t file_subcall_ctr;
Marlin/dogm_bitmaps.h
+3 -3
View File
@@ -134,7 +134,7 @@
// STATUS_SCREEN_HOTEND_TEXT_X(i) to modify draw locations.
#include "_Statusscreen.h"
#elif HAS_TEMP_BED
#elif HAS_HEATED_BED
#define STATUS_SCREEN_X ( 8 + (HOTENDS ? 0 : 64))
#define STATUS_SCREENWIDTH (120 - (HOTENDS ? 0 : 64))
@@ -319,7 +319,7 @@
};
#endif // HOTENDS
#else // !HAS_TEMP_BED
#else // !HAS_HEATED_BED
#define STATUS_SCREEN_X ( 8 + (HOTENDS ? 0 : 96))
#define STATUS_SCREENWIDTH (120 - (HOTENDS ? 0 : 96))
@@ -505,7 +505,7 @@
#endif // HOTENDS
#endif // !HAS_TEMP_BED
#endif // !HAS_HEATED_BED
#if ENABLED(BABYSTEP_ZPROBE_GFX_OVERLAY) || ENABLED(MESH_EDIT_GFX_OVERLAY)
Marlin/example_configurations/AlephObjects/TAZ4/Configuration.h
+8
View File
@@ -692,6 +692,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1060,6 +1063,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/AlephObjects/TAZ4/Configuration_adv.h
+10
View File
@@ -555,6 +555,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/example_configurations/AliExpress/CL-260/Configuration.h
+8
View File
@@ -672,6 +672,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1040,6 +1043,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/Anet/A6/Configuration.h
+8
View File
@@ -720,6 +720,9 @@
* readings with inductive probes and piezo sensors.
*/
#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1178,6 +1181,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/Anet/A6/Configuration_adv.h
+10
View File
@@ -555,6 +555,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/example_configurations/Anet/A8/Configuration.h
+8
View File
@@ -679,6 +679,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1058,6 +1061,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/Anet/A8/Configuration_adv.h
+10
View File
@@ -555,6 +555,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/example_configurations/BIBO/TouchX/Cyclops/Configuration.h
+8
View File
@@ -672,6 +672,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1040,6 +1043,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// Add a menu item to move between bed corners for manual bed adjustment
#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/BIBO/TouchX/Cyclops/Configuration_adv.h
+10
View File
@@ -555,6 +555,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/example_configurations/BIBO/TouchX/default/Configuration.h
+8
View File
@@ -672,6 +672,9 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1040,6 +1043,11 @@ const bool Z_MIN_PROBE_ENDSTOP_INVERTING = true; // set to true to invert the lo
// Add a menu item to move between bed corners for manual bed adjustment
#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/BIBO/TouchX/default/Configuration_adv.h
+10
View File
@@ -555,6 +555,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/example_configurations/BQ/Hephestos/Configuration.h
+8
View File
@@ -660,6 +660,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1028,6 +1031,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/BQ/Hephestos/Configuration_adv.h
+10
View File
@@ -555,6 +555,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/example_configurations/BQ/Hephestos_2/Configuration.h
+8
View File
@@ -673,6 +673,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1052,6 +1055,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/BQ/Hephestos_2/Configuration_adv.h
+10
View File
@@ -555,6 +555,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/example_configurations/BQ/WITBOX/Configuration.h
+8
View File
@@ -660,6 +660,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1028,6 +1031,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/BQ/WITBOX/Configuration_adv.h
+10
View File
@@ -555,6 +555,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/example_configurations/Cartesio/Configuration.h
+8
View File
@@ -671,6 +671,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1039,6 +1042,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/Cartesio/Configuration_adv.h
+10
View File
@@ -555,6 +555,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/example_configurations/Creality/CR-10/Configuration.h
+8
View File
@@ -682,6 +682,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1050,6 +1053,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/Creality/CR-10/Configuration_adv.h
+10
View File
@@ -555,6 +555,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/example_configurations/Creality/CR-10S/Configuration.h
+8
View File
@@ -672,6 +672,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1041,6 +1044,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/Creality/CR-10S/Configuration_adv.h
+10
View File
@@ -555,6 +555,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/example_configurations/Creality/CR-10mini/Configuration.h
+8
View File
@@ -691,6 +691,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1059,6 +1062,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/Creality/CR-10mini/Configuration_adv.h
+10
View File
@@ -555,6 +555,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/example_configurations/Creality/CR-8/Configuration.h
+5
View File
@@ -1049,6 +1049,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/Creality/CR-8/Configuration_adv.h
+10
View File
@@ -554,6 +554,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/example_configurations/Creality/Ender-2/Configuration.h
+8
View File
@@ -676,6 +676,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1044,6 +1047,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/Creality/Ender-2/Configuration_adv.h
+10
View File
@@ -555,6 +555,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/example_configurations/Creality/Ender-4/Configuration.h
+8
View File
@@ -682,6 +682,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1050,6 +1053,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/Creality/Ender-4/Configuration_adv.h
+10
View File
@@ -555,6 +555,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/example_configurations/Felix/Configuration.h
+8
View File
@@ -654,6 +654,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1022,6 +1025,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/Felix/Configuration_adv.h
+10
View File
@@ -555,6 +555,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/example_configurations/Felix/DUAL/Configuration.h
+8
View File
@@ -654,6 +654,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1022,6 +1025,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/FolgerTech/i3-2020/Configuration.h
+8
View File
@@ -678,6 +678,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1064,6 +1067,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/FolgerTech/i3-2020/Configuration_adv.h
+10
View File
@@ -555,6 +555,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/example_configurations/Geeetech/GT2560/Configuration.h
+8
View File
@@ -687,6 +687,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1055,6 +1058,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/Geeetech/I3_Pro_X-GT2560/Configuration.h
+8
View File
@@ -672,6 +672,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1040,6 +1043,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h
+8
View File
@@ -688,6 +688,9 @@
* readings with inductive probes and piezo sensors.
*/
#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
#define PROBING_FANS_OFF // Turn fans off when probing
#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1056,6 +1059,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h
+9 -1
View File
@@ -686,7 +686,10 @@
* These options are most useful for the BLTouch probe, but may also improve
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1055,6 +1058,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/Infitary/i3-M508/Configuration.h
+8
View File
@@ -676,6 +676,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1044,6 +1047,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/Infitary/i3-M508/Configuration_adv.h
+10
View File
@@ -555,6 +555,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/example_configurations/JGAurora/A5/Configuration.h
+8
View File
@@ -684,6 +684,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1051,6 +1054,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/JGAurora/A5/Configuration_adv.h
+10
View File
@@ -555,6 +555,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/example_configurations/Malyan/M150/Configuration.h
+8
View File
@@ -692,6 +692,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1079,6 +1082,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/Malyan/M150/Configuration_adv.h
+10
View File
@@ -555,6 +555,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/example_configurations/Micromake/C1/basic/Configuration.h
+8
View File
@@ -676,6 +676,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1044,6 +1047,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/Micromake/C1/enhanced/Configuration.h
+8
View File
@@ -676,6 +676,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1044,6 +1047,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/Micromake/C1/enhanced/Configuration_adv.h
+10
View File
@@ -555,6 +555,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/example_configurations/RepRapPro/Huxley/Configuration.h
+5
View File
@@ -1089,6 +1089,11 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h
+8
View File
@@ -672,6 +672,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1040,6 +1043,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/RigidBot/Configuration.h
+8
View File
@@ -670,6 +670,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1038,6 +1041,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/RigidBot/Configuration_adv.h
+10
View File
@@ -555,6 +555,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/example_configurations/SCARA/Configuration.h
+18 -10
View File
@@ -505,23 +505,23 @@
// Specify here all the endstop connectors that are connected to any endstop or probe.
// Almost all printers will be using one per axis. Probes will use one or more of the
// extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
#define USE_XMIN_PLUG
#define USE_YMIN_PLUG
//#define USE_XMIN_PLUG
//#define USE_YMIN_PLUG
#define USE_ZMIN_PLUG
//#define USE_XMAX_PLUG
//#define USE_YMAX_PLUG
#define USE_XMAX_PLUG
#define USE_YMAX_PLUG
//#define USE_ZMAX_PLUG
// Enable pullup for all endstops to prevent a floating state
//#define ENDSTOPPULLUPS
#if DISABLED(ENDSTOPPULLUPS)
// Disable ENDSTOPPULLUPS to set pullups individually
//#define ENDSTOPPULLUP_XMAX
//#define ENDSTOPPULLUP_YMAX
#define ENDSTOPPULLUP_ZMAX // open pin, inverted
#define ENDSTOPPULLUP_XMIN // open pin, inverted
#define ENDSTOPPULLUP_YMIN // open pin, inverted
//#define ENDSTOPPULLUP_ZMIN
#define ENDSTOPPULLUP_XMAX
#define ENDSTOPPULLUP_YMAX
//#define ENDSTOPPULLUP_ZMAX // open pin, inverted
//#define ENDSTOPPULLUP_XMIN // open pin, inverted
//#define ENDSTOPPULLUP_YMIN // open pin, inverted
#define ENDSTOPPULLUP_ZMIN
//#define ENDSTOPPULLUP_ZMIN_PROBE
#endif
@@ -684,6 +684,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1052,6 +1055,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/SCARA/Configuration_adv.h
+10
View File
@@ -555,6 +555,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/example_configurations/Sanguinololu/Configuration.h
+8
View File
@@ -703,6 +703,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1071,6 +1074,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/Sanguinololu/Configuration_adv.h
+10
View File
@@ -555,6 +555,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/example_configurations/TinyBoy2/Configuration.h
+8
View File
@@ -723,6 +723,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1096,6 +1099,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/TinyBoy2/Configuration_adv.h
+10
View File
@@ -555,6 +555,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/example_configurations/Tronxy/X1/Configuration.h
+8
View File
@@ -672,6 +672,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1040,6 +1043,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/Tronxy/X5S/Configuration.h
+8
View File
@@ -672,6 +672,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1040,6 +1043,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/Tronxy/XY100/Configuration.h
+8
View File
@@ -683,6 +683,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1051,6 +1054,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/Velleman/K8200/Configuration.h
+8
View File
@@ -701,6 +701,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1070,6 +1073,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/Velleman/K8200/Configuration_adv.h
+10
View File
@@ -568,6 +568,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/example_configurations/Velleman/K8400/Configuration.h
+8
View File
@@ -672,6 +672,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1040,6 +1043,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/Velleman/K8400/Configuration_adv.h
+10
View File
@@ -555,6 +555,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/example_configurations/Velleman/K8400/Dual-head/Configuration.h
+8
View File
@@ -672,6 +672,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1040,6 +1043,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/Wanhao/Duplicator 6/Configuration.h
+8
View File
@@ -682,6 +682,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1047,6 +1050,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/Wanhao/Duplicator 6/Configuration_adv.h
+10
View File
@@ -557,6 +557,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/example_configurations/adafruit/ST7565/Configuration.h
+8
View File
@@ -672,6 +672,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1040,6 +1043,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration.h
+8
View File
@@ -754,6 +754,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1191,6 +1194,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration_adv.h
+10
View File
@@ -557,6 +557,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/example_configurations/delta/FLSUN/kossel/Configuration.h
+8
View File
@@ -754,6 +754,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1173,6 +1176,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/delta/FLSUN/kossel/Configuration_adv.h
+10
View File
@@ -557,6 +557,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration.h
+8
View File
@@ -754,6 +754,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1172,6 +1175,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration_adv.h
+10
View File
@@ -557,6 +557,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/example_configurations/delta/Hatchbox_Alpha/Configuration.h
+9 -1
View File
@@ -129,7 +129,7 @@
// The following define selects which electronics board you have.
// Please choose the name from boards.h that matches your setup
#ifndef MOTHERBOARD
#define MOTHERBOARD BOARD_MKS_13
#define MOTHERBOARD BOARD_MKS_GEN_13
#endif
// Optional custom name for your RepStrap or other custom machine
@@ -759,6 +759,9 @@
* readings with inductive probes and piezo sensors.
*/
#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1186,6 +1189,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/delta/generic/Configuration.h
+8
View File
@@ -744,6 +744,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1160,6 +1163,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/delta/generic/Configuration_adv.h
+10
View File
@@ -557,6 +557,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/example_configurations/delta/kossel_mini/Configuration.h
+8
View File
@@ -744,6 +744,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1163,6 +1166,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/delta/kossel_mini/Configuration_adv.h
+10
View File
@@ -557,6 +557,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/example_configurations/delta/kossel_pro/Configuration.h
+8
View File
@@ -729,6 +729,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1154,6 +1157,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/delta/kossel_pro/Configuration_adv.h
+10
View File
@@ -562,6 +562,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/example_configurations/delta/kossel_xl/Configuration.h
+8
View File
@@ -747,6 +747,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1163,6 +1166,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.
Marlin/example_configurations/delta/kossel_xl/Configuration_adv.h
+10
View File
@@ -557,6 +557,16 @@
// Add an option in the menu to run all auto#.g files
//#define MENU_ADDAUTOSTART
/**
* Continue after Power-Loss (Creality3D)
*
* Store the current state to the SD Card at the start of each layer
* during SD printing. If the recovery file is found at boot time, present
* an option on the LCD screen to continue the print from the last-known
* point in the file.
*/
//#define POWER_LOSS_RECOVERY
/**
* Sort SD file listings in alphabetical order.
*
Marlin/example_configurations/gCreate/gMax1.5+/Configuration.h
+8
View File
@@ -685,6 +685,9 @@
* readings with inductive probes and piezo sensors.
*/
//#define PROBING_HEATERS_OFF // Turn heaters off when probing
#if ENABLED(PROBING_HEATERS_OFF)
//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)
#endif
//#define PROBING_FANS_OFF // Turn fans off when probing
//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors
@@ -1061,6 +1064,11 @@
// Add a menu item to move between bed corners for manual bed adjustment
//#define LEVEL_BED_CORNERS
#if ENABLED(LEVEL_BED_CORNERS)
#define LEVEL_CORNERS_INSET 30 // (mm) An inset for corner leveling
//#define LEVEL_CENTER_TOO // Move to the center after the last corner
#endif
/**
* Commands to execute at the end of G29 probing.
* Useful to retract or move the Z probe out of the way.

Some files were not shown because too many files have changed in this diff Show More