10s pro support and basic dwin files to start changes
This commit is contained in:
InsanityAutomation
+909
-194
File diff suppressed because it is too large
Load Diff
+203
-115
@@ -74,10 +74,10 @@
|
||||
* THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
|
||||
*/
|
||||
#if ENABLED(THERMAL_PROTECTION_HOTENDS)
|
||||
#define THERMAL_PROTECTION_PERIOD 40 // Seconds
|
||||
#define THERMAL_PROTECTION_HYSTERESIS 4 // Degrees Celsius
|
||||
#define THERMAL_PROTECTION_PERIOD 60 // Seconds
|
||||
#define THERMAL_PROTECTION_HYSTERESIS 10 // Degrees Celsius
|
||||
|
||||
//#define ADAPTIVE_FAN_SLOWING // Slow part cooling fan if temperature drops
|
||||
#define ADAPTIVE_FAN_SLOWING // Slow part cooling fan if temperature drops
|
||||
#if ENABLED(ADAPTIVE_FAN_SLOWING) && ENABLED(PIDTEMP)
|
||||
//#define NO_FAN_SLOWING_IN_PID_TUNING // Don't slow fan speed during M303
|
||||
#endif
|
||||
@@ -94,7 +94,7 @@
|
||||
* and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set
|
||||
* below 2.
|
||||
*/
|
||||
#define WATCH_TEMP_PERIOD 20 // Seconds
|
||||
#define WATCH_TEMP_PERIOD 50 // Seconds
|
||||
#define WATCH_TEMP_INCREASE 2 // Degrees Celsius
|
||||
#endif
|
||||
|
||||
@@ -102,14 +102,25 @@
|
||||
* Thermal Protection parameters for the bed are just as above for hotends.
|
||||
*/
|
||||
#if ENABLED(THERMAL_PROTECTION_BED)
|
||||
#define THERMAL_PROTECTION_BED_PERIOD 20 // Seconds
|
||||
#if(ENABLED(BedDC))
|
||||
|
||||
#define THERMAL_PROTECTION_BED_PERIOD 50 // Seconds
|
||||
#define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
|
||||
|
||||
#define WATCH_BED_TEMP_PERIOD 180 // Seconds
|
||||
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
|
||||
#else
|
||||
|
||||
#define THERMAL_PROTECTION_BED_PERIOD 30 // Seconds
|
||||
#define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
|
||||
|
||||
#define WATCH_BED_TEMP_PERIOD 120 // Seconds
|
||||
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
|
||||
#endif
|
||||
|
||||
/**
|
||||
* As described above, except for the bed (M140/M190/M303).
|
||||
*/
|
||||
#define WATCH_BED_TEMP_PERIOD 60 // Seconds
|
||||
#define WATCH_BED_TEMP_INCREASE 2 // Degrees Celsius
|
||||
#endif
|
||||
|
||||
/**
|
||||
@@ -146,14 +157,17 @@
|
||||
* Also, if the temperature is set to a value below mintemp, it will not be changed by autotemp.
|
||||
* On an Ultimaker, some initial testing worked with M109 S215 B260 F1 in the start.gcode
|
||||
*/
|
||||
#if(DISABLED(MachineCR10Orig) && DISABLED(LowMemoryBoard))
|
||||
#define AUTOTEMP
|
||||
#endif
|
||||
#if ENABLED(AUTOTEMP)
|
||||
#define AUTOTEMP_OLDWEIGHT 0.98
|
||||
#endif
|
||||
|
||||
// Show extra position information in M114
|
||||
//#define M114_DETAIL
|
||||
|
||||
#if(DISABLED(MachineCR10Orig) && DISABLED(LowMemoryBoard))
|
||||
#define M114_DETAIL
|
||||
#endif
|
||||
// Show Temperature ADC value
|
||||
// Enable for M105 to include ADC values read from temperature sensors.
|
||||
//#define SHOW_TEMP_ADC_VALUES
|
||||
@@ -224,7 +238,7 @@
|
||||
// When first starting the main fan, run it at full speed for the
|
||||
// given number of milliseconds. This gets the fan spinning reliably
|
||||
// before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
|
||||
//#define FAN_KICKSTART_TIME 100
|
||||
#define FAN_KICKSTART_TIME 100
|
||||
|
||||
/**
|
||||
* PWM Fan Scaling
|
||||
@@ -306,13 +320,15 @@
|
||||
/**
|
||||
* M355 Case Light on-off / brightness
|
||||
*/
|
||||
//#define CASE_LIGHT_ENABLE
|
||||
#if(ENABLED(EnclosureLight))
|
||||
#define CASE_LIGHT_ENABLE
|
||||
#endif
|
||||
#if ENABLED(CASE_LIGHT_ENABLE)
|
||||
//#define CASE_LIGHT_PIN 4 // Override the default pin if needed
|
||||
#define CASE_LIGHT_PIN 12 // Override the default pin if needed
|
||||
#define INVERT_CASE_LIGHT false // Set true if Case Light is ON when pin is LOW
|
||||
#define CASE_LIGHT_DEFAULT_ON true // Set default power-up state on
|
||||
#define CASE_LIGHT_DEFAULT_BRIGHTNESS 105 // Set default power-up brightness (0-255, requires PWM pin)
|
||||
//#define MENU_ITEM_CASE_LIGHT // Add a Case Light option to the LCD main menu
|
||||
#define CASE_LIGHT_DEFAULT_BRIGHTNESS 255 // Set default power-up brightness (0-255, requires PWM pin)
|
||||
#define MENU_ITEM_CASE_LIGHT // Add a Case Light option to the LCD main menu
|
||||
//#define CASE_LIGHT_USE_NEOPIXEL // Use Neopixel LED as case light, requires NEOPIXEL_LED.
|
||||
#if ENABLED(CASE_LIGHT_USE_NEOPIXEL)
|
||||
#define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White }
|
||||
@@ -455,7 +471,7 @@
|
||||
#define Y_HOME_BUMP_MM 5
|
||||
#define Z_HOME_BUMP_MM 2
|
||||
#define HOMING_BUMP_DIVISOR { 2, 2, 4 } // Re-Bump Speed Divisor (Divides the Homing Feedrate)
|
||||
//#define QUICK_HOME // If homing includes X and Y, do a diagonal move initially
|
||||
#define QUICK_HOME // If homing includes X and Y, do a diagonal move initially
|
||||
|
||||
// When G28 is called, this option will make Y home before X
|
||||
//#define HOME_Y_BEFORE_X
|
||||
@@ -525,8 +541,9 @@
|
||||
#define DEFAULT_MINSEGMENTTIME 20000
|
||||
|
||||
// If defined the movements slow down when the look ahead buffer is only half full
|
||||
#if(DISABLED(MachineCR10Orig) && DISABLED(LowMemoryBoard))
|
||||
#define SLOWDOWN
|
||||
|
||||
#endif
|
||||
// Frequency limit
|
||||
// See nophead's blog for more info
|
||||
// Not working O
|
||||
@@ -535,7 +552,7 @@
|
||||
// Minimum planner junction speed. Sets the default minimum speed the planner plans for at the end
|
||||
// of the buffer and all stops. This should not be much greater than zero and should only be changed
|
||||
// if unwanted behavior is observed on a user's machine when running at very slow speeds.
|
||||
#define MINIMUM_PLANNER_SPEED 0.05 // (mm/s)
|
||||
#define MINIMUM_PLANNER_SPEED 0.05 // (mm/sec)
|
||||
|
||||
//
|
||||
// Backlash Compensation
|
||||
@@ -704,30 +721,33 @@
|
||||
#define ENCODER_100X_STEPS_PER_SEC 80 // (steps/s) Encoder rate for 100x speed
|
||||
#endif
|
||||
|
||||
// Play a beep when the feedrate is changed from the Status Screen
|
||||
//#define BEEP_ON_FEEDRATE_CHANGE
|
||||
#if ENABLED(BEEP_ON_FEEDRATE_CHANGE)
|
||||
#define FEEDRATE_CHANGE_BEEP_DURATION 10
|
||||
#define FEEDRATE_CHANGE_BEEP_FREQUENCY 440
|
||||
// Include a page of printer information in the LCD Main Menu
|
||||
#if(DISABLED(MachineCR10Orig))
|
||||
#define LCD_INFO_MENU
|
||||
#endif
|
||||
// Leave out seldom-used LCD menu items to recover some Program Memory
|
||||
#if(ENABLED(MachineCR10Orig) || ENABLED(LowMemoryBoard))
|
||||
#define SLIM_LCD_MENUS
|
||||
#endif
|
||||
|
||||
// Include a page of printer information in the LCD Main Menu
|
||||
//#define LCD_INFO_MENU
|
||||
|
||||
// Scroll a longer status message into view
|
||||
//#define STATUS_MESSAGE_SCROLLING
|
||||
#if(DISABLED(MachineCR10Orig) && DISABLED(LowMemoryBoard))
|
||||
#define STATUS_MESSAGE_SCROLLING
|
||||
|
||||
// On the Info Screen, display XY with one decimal place when possible
|
||||
//#define LCD_DECIMAL_SMALL_XY
|
||||
|
||||
#define LCD_DECIMAL_SMALL_XY
|
||||
#endif
|
||||
// The timeout (in ms) to return to the status screen from sub-menus
|
||||
//#define LCD_TIMEOUT_TO_STATUS 15000
|
||||
#define LCD_TIMEOUT_TO_STATUS 15000
|
||||
|
||||
// Add an 'M73' G-code to set the current percentage
|
||||
//#define LCD_SET_PROGRESS_MANUALLY
|
||||
|
||||
#if HAS_CHARACTER_LCD && HAS_PRINT_PROGRESS
|
||||
//#define LCD_PROGRESS_BAR // Show a progress bar on HD44780 LCDs for SD printing
|
||||
#if(DISABLED(MachineCR10Orig) && DISABLED(LowMemoryBoard))
|
||||
#define LCD_SET_PROGRESS_MANUALLY
|
||||
#endif
|
||||
#if ENABLED(SDSUPPORT) || ENABLED(LCD_SET_PROGRESS_MANUALLY)
|
||||
#if((ENABLED(MachineEnder4) && DISABLED(GraphicLCD)))
|
||||
#define LCD_PROGRESS_BAR
|
||||
#endif// Show a progress bar on HD44780 LCDs for SD printing
|
||||
#if ENABLED(LCD_PROGRESS_BAR)
|
||||
#define PROGRESS_BAR_BAR_TIME 2000 // (ms) Amount of time to show the bar
|
||||
#define PROGRESS_BAR_MSG_TIME 3000 // (ms) Amount of time to show the status message
|
||||
@@ -735,7 +755,7 @@
|
||||
//#define PROGRESS_MSG_ONCE // Show the message for MSG_TIME then clear it
|
||||
//#define LCD_PROGRESS_BAR_TEST // Add a menu item to test the progress bar
|
||||
#endif
|
||||
#endif
|
||||
#endif // SDSUPPORT || LCD_SET_PROGRESS_MANUALLY
|
||||
|
||||
/**
|
||||
* LED Control Menu
|
||||
@@ -768,8 +788,9 @@
|
||||
|
||||
// Reverse SD sort to show "more recent" files first, according to the card's FAT.
|
||||
// Since the FAT gets out of order with usage, SDCARD_SORT_ALPHA is recommended.
|
||||
#if(DISABLED(MachineCR10Orig) && DISABLED(LowMemoryBoard))
|
||||
#define SDCARD_RATHERRECENTFIRST
|
||||
|
||||
#endif
|
||||
// Add an option in the menu to run all auto#.g files
|
||||
//#define MENU_ADDAUTOSTART
|
||||
|
||||
@@ -829,8 +850,9 @@
|
||||
//#define LONG_FILENAME_HOST_SUPPORT
|
||||
|
||||
// Enable this option to scroll long filenames in the SD card menu
|
||||
//#define SCROLL_LONG_FILENAMES
|
||||
|
||||
#if(DISABLED(MachineCR10Orig) && DISABLED(LowMemoryBoard))
|
||||
#define SCROLL_LONG_FILENAMES
|
||||
#endif
|
||||
/**
|
||||
* This option allows you to abort SD printing when any endstop is triggered.
|
||||
* This feature must be enabled with "M540 S1" or from the LCD menu.
|
||||
@@ -913,8 +935,9 @@
|
||||
|
||||
// A bigger font is available for edit items. Costs 3120 bytes of PROGMEM.
|
||||
// Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
|
||||
#if(DISABLED(MachineCR10Orig) && DISABLED(LowMemoryBoard))
|
||||
//#define USE_BIG_EDIT_FONT
|
||||
|
||||
#endif
|
||||
// A smaller font may be used on the Info Screen. Costs 2300 bytes of PROGMEM.
|
||||
// Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
|
||||
//#define USE_SMALL_INFOFONT
|
||||
@@ -939,7 +962,9 @@
|
||||
* This will prevent position updates from being displayed.
|
||||
*/
|
||||
#if ENABLED(U8GLIB_ST7920)
|
||||
//#define LIGHTWEIGHT_UI
|
||||
#if ENABLED(Big_UI)
|
||||
#define LIGHTWEIGHT_UI
|
||||
#endif
|
||||
#if ENABLED(LIGHTWEIGHT_UI)
|
||||
#define STATUS_EXPIRE_SECONDS 20
|
||||
#endif
|
||||
@@ -984,29 +1009,29 @@
|
||||
*
|
||||
* Warning: Does not respect endstops!
|
||||
*/
|
||||
//#define BABYSTEPPING
|
||||
#define BABYSTEPPING
|
||||
#if ENABLED(BABYSTEPPING)
|
||||
//#define BABYSTEP_WITHOUT_HOMING
|
||||
//#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA!
|
||||
#define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way
|
||||
#define BABYSTEP_MULTIPLICATOR 1 // Babysteps are very small. Increase for faster motion.
|
||||
//#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA!
|
||||
#define BABYSTEP_INVERT_Z false // Change if Z babysteps should go the other way
|
||||
#define BABYSTEP_MULTIPLICATOR 10 // Babysteps are very small. Increase for faster motion.
|
||||
#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
|
||||
|
||||
//#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
|
||||
#if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING)
|
||||
#define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
|
||||
// Note: Extra time may be added to mitigate controller latency.
|
||||
//#define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement).
|
||||
//#define MOVE_Z_WHEN_IDLE // Jump to the move Z menu on doubleclick when printer is idle.
|
||||
#if ENABLED(ABL_EZABL) || ENABLED(ABL_BLTOUCH) || ENABLED(ABL_NCSW)
|
||||
#if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING)
|
||||
#define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
|
||||
// Note: Extra time may be added to mitigate controller latency.
|
||||
#define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement).
|
||||
#define BABYSTEP_ZPROBE_OFFSET // Enable to combine M851 and Babystepping
|
||||
#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
|
||||
#endif
|
||||
|
||||
//#define MOVE_Z_WHEN_IDLE // Jump to the move Z menu on doubleclick when printer is idle.
|
||||
#if ENABLED(MOVE_Z_WHEN_IDLE)
|
||||
#define MOVE_Z_IDLE_MULTIPLICATOR 1 // Multiply 1mm by this factor for the move step size.
|
||||
#define MOVE_Z_IDLE_MULTIPLICATOR 1 // Multiply 1mm by this factor for the move step size.
|
||||
#endif
|
||||
#endif
|
||||
|
||||
//#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping
|
||||
#if ENABLED(BABYSTEP_ZPROBE_OFFSET)
|
||||
//#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
|
||||
//#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
|
||||
#endif
|
||||
#endif
|
||||
|
||||
// @section extruder
|
||||
@@ -1027,9 +1052,11 @@
|
||||
* See http://marlinfw.org/docs/features/lin_advance.html for full instructions.
|
||||
* Mention @Sebastianv650 on GitHub to alert the author of any issues.
|
||||
*/
|
||||
//#define LIN_ADVANCE
|
||||
#if ((DISABLED(MachineCR10Orig) && DISABLED(LowMemoryBoard)) || ENABLED(OrigLA)) && DISABLED(MachineCR10SPro)
|
||||
#define LIN_ADVANCE
|
||||
#endif
|
||||
#if ENABLED(LIN_ADVANCE)
|
||||
#define LIN_ADVANCE_K 0.22 // Unit: mm compression per 1mm/s extruder speed
|
||||
#define LIN_ADVANCE_K 0.5 // Unit: mm compression per 1mm/s extruder speed
|
||||
//#define LA_DEBUG // If enabled, this will generate debug information output over USB.
|
||||
#endif
|
||||
|
||||
@@ -1037,6 +1064,35 @@
|
||||
|
||||
#if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
|
||||
// Override the mesh area if the automatic (max) area is too large
|
||||
|
||||
#if( (X_PROBE_OFFSET_FROM_EXTRUDER + 15) > 0 )
|
||||
#define MESH_MIN_X (X_PROBE_OFFSET_FROM_EXTRUDER + 5)
|
||||
#else
|
||||
#define MESH_MIN_X 10
|
||||
#endif
|
||||
|
||||
#if( (X_BED_SIZE + X_PROBE_OFFSET_FROM_EXTRUDER - 10) < X_BED_SIZE)
|
||||
#define MESH_MAX_X (X_BED_SIZE + X_PROBE_OFFSET_FROM_EXTRUDER - 5)
|
||||
#else
|
||||
#if(ENABLED(MachineEnder3))
|
||||
#define MESH_MAX_X (X_BED_SIZE - 40)
|
||||
#else
|
||||
#define MESH_MAX_X (X_BED_SIZE - 10)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
#if ( (Y_PROBE_OFFSET_FROM_EXTRUDER + 25) > 10 )
|
||||
#define MESH_MIN_Y (Y_PROBE_OFFSET_FROM_EXTRUDER + 25)
|
||||
#else
|
||||
#define MESH_MIN_Y 25
|
||||
#endif
|
||||
|
||||
#if( (Y_BED_SIZE + Y_PROBE_OFFSET_FROM_EXTRUDER - 25) < Y_BED_SIZE)
|
||||
#define MESH_MAX_Y (Y_BED_SIZE + Y_PROBE_OFFSET_FROM_EXTRUDER - 25)
|
||||
#else
|
||||
#define MESH_MAX_Y (Y_BED_SIZE - 25)
|
||||
#endif
|
||||
|
||||
//#define MESH_MIN_X MESH_INSET
|
||||
//#define MESH_MIN_Y MESH_INSET
|
||||
//#define MESH_MAX_X X_BED_SIZE - (MESH_INSET)
|
||||
@@ -1047,9 +1103,11 @@
|
||||
* Repeatedly attempt G29 leveling until it succeeds.
|
||||
* Stop after G29_MAX_RETRIES attempts.
|
||||
*/
|
||||
//#define G29_RETRY_AND_RECOVER
|
||||
#if ENABLED(ABL_BI)
|
||||
#define G29_RETRY_AND_RECOVER
|
||||
#endif
|
||||
#if ENABLED(G29_RETRY_AND_RECOVER)
|
||||
#define G29_MAX_RETRIES 3
|
||||
#define G29_MAX_RETRIES 1
|
||||
#define G29_HALT_ON_FAILURE
|
||||
/**
|
||||
* Specify the GCODE commands that will be executed when leveling succeeds,
|
||||
@@ -1148,7 +1206,11 @@
|
||||
// The number of linear motions that can be in the plan at any give time.
|
||||
// THE BLOCK_BUFFER_SIZE NEEDS TO BE A POWER OF 2 (e.g. 8, 16, 32) because shifts and ors are used to do the ring-buffering.
|
||||
#if ENABLED(SDSUPPORT)
|
||||
#define BLOCK_BUFFER_SIZE 16 // SD,LCD,Buttons take more memory, block buffer needs to be smaller
|
||||
#if(ENABLED(MachineCR10Orig) || ENABLED(LowMemoryBoard))
|
||||
#define BLOCK_BUFFER_SIZE 4 // SD,LCD,Buttons take more memory, block buffer needs to be smaller
|
||||
#else
|
||||
#define BLOCK_BUFFER_SIZE 16
|
||||
#endif
|
||||
#else
|
||||
#define BLOCK_BUFFER_SIZE 16 // maximize block buffer
|
||||
#endif
|
||||
@@ -1157,8 +1219,11 @@
|
||||
|
||||
// The ASCII buffer for serial input
|
||||
#define MAX_CMD_SIZE 96
|
||||
#if(ENABLED(MachineCR10Orig) || ENABLED(LowMemoryBoard))
|
||||
#define BUFSIZE 2
|
||||
#else
|
||||
#define BUFSIZE 4
|
||||
|
||||
#endif
|
||||
// Transmission to Host Buffer Size
|
||||
// To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0.
|
||||
// To buffer a simple "ok" you need 4 bytes.
|
||||
@@ -1194,16 +1259,16 @@
|
||||
// enter the serial receive buffer, so they cannot be blocked.
|
||||
// Currently handles M108, M112, M410
|
||||
// Does not work on boards using AT90USB (USBCON) processors!
|
||||
//#define EMERGENCY_PARSER
|
||||
#define EMERGENCY_PARSER
|
||||
|
||||
// Bad Serial-connections can miss a received command by sending an 'ok'
|
||||
// Therefore some clients abort after 30 seconds in a timeout.
|
||||
// Some other clients start sending commands while receiving a 'wait'.
|
||||
// This "wait" is only sent when the buffer is empty. 1 second is a good value here.
|
||||
//#define NO_TIMEOUTS 1000 // Milliseconds
|
||||
#define NO_TIMEOUTS 1000 // Milliseconds
|
||||
|
||||
// Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary.
|
||||
//#define ADVANCED_OK
|
||||
#define ADVANCED_OK
|
||||
|
||||
// Printrun may have trouble receiving long strings all at once.
|
||||
// This option inserts short delays between lines of serial output.
|
||||
@@ -1235,17 +1300,16 @@
|
||||
* Note that M207 / M208 / M209 settings are saved to EEPROM.
|
||||
*
|
||||
*/
|
||||
//#define FWRETRACT
|
||||
#if(DISABLED(MachineCR10Orig) && DISABLED(LowMemoryBoard))
|
||||
#define FWRETRACT // ONLY PARTIALLY TESTED
|
||||
#endif
|
||||
#if ENABLED(FWRETRACT)
|
||||
#define FWRETRACT_AUTORETRACT // costs ~500 bytes of PROGMEM
|
||||
#if ENABLED(FWRETRACT_AUTORETRACT)
|
||||
#define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over
|
||||
#define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion
|
||||
#endif
|
||||
#define MIN_AUTORETRACT 0.1 // When auto-retract is on, convert E moves of this length and over
|
||||
#define MAX_AUTORETRACT 10.0 // Upper limit for auto-retract conversion
|
||||
#define RETRACT_LENGTH 3 // Default retract length (positive mm)
|
||||
#define RETRACT_LENGTH_SWAP 13 // Default swap retract length (positive mm), for extruder change
|
||||
#define RETRACT_FEEDRATE 45 // Default feedrate for retracting (mm/s)
|
||||
#define RETRACT_ZRAISE 0 // Default retract Z-raise (mm)
|
||||
#define RETRACT_ZRAISE 0 // Default retract Z-lift
|
||||
#define RETRACT_RECOVER_LENGTH 0 // Default additional recover length (mm, added to retract length when recovering)
|
||||
#define RETRACT_RECOVER_LENGTH_SWAP 0 // Default additional swap recover length (mm, added to retract length when recovering from extruder change)
|
||||
#define RETRACT_RECOVER_FEEDRATE 8 // Default feedrate for recovering from retraction (mm/s)
|
||||
@@ -1261,22 +1325,21 @@
|
||||
*/
|
||||
#if EXTRUDERS > 1
|
||||
// Z raise distance for tool-change, as needed for some extruders
|
||||
#define TOOLCHANGE_ZRAISE 2 // (mm)
|
||||
#define TOOLCHANGE_ZRAISE 1 // (mm)
|
||||
|
||||
// Retract and prime filament on tool-change
|
||||
//#define TOOLCHANGE_FILAMENT_SWAP
|
||||
#define TOOLCHANGE_FILAMENT_SWAP
|
||||
#if ENABLED(TOOLCHANGE_FILAMENT_SWAP)
|
||||
#define TOOLCHANGE_FIL_SWAP_LENGTH 12 // (mm)
|
||||
#define TOOLCHANGE_FIL_EXTRA_PRIME 2 // (mm)
|
||||
#define TOOLCHANGE_FIL_SWAP_RETRACT_SPEED 3600 // (mm/m)
|
||||
#define TOOLCHANGE_FIL_SWAP_PRIME_SPEED 3600 // (mm/m)
|
||||
#define TOOLCHANGE_FIL_SWAP_LENGTH 80 // (mm)
|
||||
#define TOOLCHANGE_FIL_SWAP_RETRACT_SPEED 3000 // (mm/m)
|
||||
#define TOOLCHANGE_FIL_SWAP_PRIME_SPEED 3000 // (mm/m)
|
||||
#endif
|
||||
|
||||
/**
|
||||
* Position to park head during tool change.
|
||||
* Doesn't apply to SWITCHING_TOOLHEAD, DUAL_X_CARRIAGE, or PARKING_EXTRUDER
|
||||
*/
|
||||
//#define TOOLCHANGE_PARK
|
||||
#define TOOLCHANGE_PARK
|
||||
#if ENABLED(TOOLCHANGE_PARK)
|
||||
#define TOOLCHANGE_PARK_XY { X_MIN_POS + 10, Y_MIN_POS + 10 }
|
||||
#define TOOLCHANGE_PARK_XY_FEEDRATE 6000 // (mm/m)
|
||||
@@ -1293,47 +1356,53 @@
|
||||
* Requires NOZZLE_PARK_FEATURE.
|
||||
* This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
|
||||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
|
||||
#define ADVANCED_PAUSE_FEATURE
|
||||
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 4 // (mm) Initial retract.
|
||||
// This short retract is done immediately, before parking the nozzle.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 10 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_FEEDRATE 41 // (mm/s) Unload filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_UNLOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 100 // (mm) The length of filament for a complete unload.
|
||||
#define FILAMENT_CHANGE_UNLOAD_LENGTH 430 // (mm) The length of filament for a complete unload.
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
// Set to 0 for manual unloading.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE 6 // (mm/s) Slow move when starting load.
|
||||
#define FILAMENT_CHANGE_SLOW_LOAD_LENGTH 0 // (mm) Slow length, to allow time to insert material.
|
||||
// 0 to disable start loading and skip to fast load only
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 6 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE 30 // (mm/s) Load filament feedrate. This can be pretty fast.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_ACCEL 25 // (mm/s^2) Lower acceleration may allow a faster feedrate.
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 0 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
#if(ENABLED(MachineCRX))
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 450 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
#else
|
||||
#define FILAMENT_CHANGE_FAST_LOAD_LENGTH 430 // (mm) Load length of filament, from extruder gear to nozzle.
|
||||
#endif
|
||||
// For Bowden, the full length of the tube and nozzle.
|
||||
// For direct drive, the full length of the nozzle.
|
||||
//#define ADVANCED_PAUSE_CONTINUOUS_PURGE // Purge continuously up to the purge length until interrupted.
|
||||
#define ADVANCED_PAUSE_PURGE_FEEDRATE 3 // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 50 // (mm) Length to extrude after loading.
|
||||
#define ADVANCED_PAUSE_PURGE_LENGTH 20 // (mm) Length to extrude after loading.
|
||||
// Set to 0 for manual extrusion.
|
||||
// Filament can be extruded repeatedly from the Filament Change menu
|
||||
// until extrusion is consistent, and to purge old filament.
|
||||
#define ADVANCED_PAUSE_RESUME_PRIME 0 // (mm) Extra distance to prime nozzle after returning from park.
|
||||
|
||||
// Filament Unload does a Retract, Delay, and Purge first:
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 13 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_RETRACT_LENGTH 4 // (mm) Unload initial retract length.
|
||||
#define FILAMENT_UNLOAD_DELAY 5000 // (ms) Delay for the filament to cool after retract.
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 8 // (mm) An unretract is done, then this length is purged.
|
||||
|
||||
#define FILAMENT_UNLOAD_PURGE_LENGTH 0 // (mm) An unretract is done, then this length is purged.
|
||||
#define PAUSE_PARK_NOZZLE_TIMEOUT 45 // (seconds) Time limit before the nozzle is turned off for safety.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 10 // Number of alert beeps to play when a response is needed.
|
||||
#define FILAMENT_CHANGE_ALERT_BEEPS 2 // Number of alert beeps to play when a response is needed.
|
||||
#define PAUSE_PARK_NO_STEPPER_TIMEOUT // Enable for XYZ steppers to stay powered on during filament change.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
#define HOME_BEFORE_FILAMENT_CHANGE // Ensure homing has been completed prior to parking for filament change
|
||||
#if(DISABLED(MachineCR10Orig) && DISABLED(LowMemoryBoard))
|
||||
#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#endif
|
||||
#endif
|
||||
|
||||
// @section tmc
|
||||
@@ -1983,13 +2052,15 @@
|
||||
/**
|
||||
* Auto-report temperatures with M155 S<seconds>
|
||||
*/
|
||||
#if(DISABLED(MachineCR10Orig) && DISABLED(LowMemoryBoard))
|
||||
#define AUTO_REPORT_TEMPERATURES
|
||||
|
||||
#endif
|
||||
/**
|
||||
* Include capabilities in M115 output
|
||||
*/
|
||||
#if(DISABLED(MachineCR10Orig))
|
||||
#define EXTENDED_CAPABILITIES_REPORT
|
||||
|
||||
#endif
|
||||
/**
|
||||
* Disable all Volumetric extrusion options
|
||||
*/
|
||||
@@ -2027,7 +2098,9 @@
|
||||
/**
|
||||
* Spend 28 bytes of SRAM to optimize the GCode parser
|
||||
*/
|
||||
#if(DISABLED(MachineCR10Orig) && DISABLED(LowMemoryBoard))
|
||||
#define FASTER_GCODE_PARSER
|
||||
#endif
|
||||
|
||||
/**
|
||||
* CNC G-code options
|
||||
@@ -2043,7 +2116,6 @@
|
||||
#ifdef G0_FEEDRATE
|
||||
//#define VARIABLE_G0_FEEDRATE // The G0 feedrate is set by F in G0 motion mode
|
||||
#endif
|
||||
|
||||
/**
|
||||
* G-code Macros
|
||||
*
|
||||
@@ -2059,27 +2131,43 @@
|
||||
/**
|
||||
* User-defined menu items that execute custom GCode
|
||||
*/
|
||||
//#define CUSTOM_USER_MENUS
|
||||
#if(ENABLED(ABL_UBL) || ENABLED(ABL_BI))
|
||||
#define CUSTOM_USER_MENUS
|
||||
#endif
|
||||
|
||||
#if ENABLED(CUSTOM_USER_MENUS)
|
||||
//#define CUSTOM_USER_MENU_TITLE "Custom Commands"
|
||||
#define USER_SCRIPT_DONE "M117 User Script Done"
|
||||
//#define USER_SCRIPT_DONE "M117 User Script Done"
|
||||
#define USER_SCRIPT_AUDIBLE_FEEDBACK
|
||||
//#define USER_SCRIPT_RETURN // Return to status screen after a script
|
||||
#define USER_SCRIPT_RETURN // Return to status screen after a script
|
||||
#define CUSTOM_USER_MENU_TITLE "Commissioning"
|
||||
|
||||
#define USER_DESC_1 "Home & UBL Info"
|
||||
#define USER_GCODE_1 "G28\nG29 W"
|
||||
#if ENABLED(BedDC)
|
||||
#define CommBedTmp "55"
|
||||
#else
|
||||
#define CommBedTmp "75"
|
||||
#endif
|
||||
|
||||
#define USER_DESC_2 "Preheat for " PREHEAT_1_LABEL
|
||||
#define USER_GCODE_2 "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND)
|
||||
#if (ENABLED(ABL_UBL))
|
||||
#define USER_DESC_1 "UBL Commission 1"
|
||||
#define USER_GCODE_1 "M502 \n M500 \n M501 \n M190 S" CommBedTmp" \n M104 S225 \n G28 \n G29 P1 \n G29 S1 \n M117 Run Step 2"
|
||||
|
||||
#define USER_DESC_3 "Preheat for " PREHEAT_2_LABEL
|
||||
#define USER_GCODE_3 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND)
|
||||
#define USER_DESC_2 "UBL Commission 2"
|
||||
#define USER_GCODE_2 "G29 S1 \n G29 S0 \n G29 F 10.0 \n G29 A \n M500 \n G28 \n G29 L1 \n M109 S225 \n G1 X100 Y 100 \n G1 Z0 \n M117 Set Z Offset"
|
||||
|
||||
#define USER_DESC_4 "Heat Bed/Home/Level"
|
||||
#define USER_GCODE_4 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29"
|
||||
#define USER_DESC_3 "Prep for Z Adjust"
|
||||
#define USER_GCODE_3 "M190 " CommBedTmp" \n M104 235 \n G28 \n G29 L1 \n G1 X100 Y 100 \n G1 Z0"
|
||||
|
||||
#define USER_DESC_5 "Home & Info"
|
||||
#define USER_GCODE_5 "G28\nM503"
|
||||
#define USER_DESC_4 "Fill Mesh Points"
|
||||
#define USER_GCODE_4 "G29 P3 \n G29 P3 \n G29 P3 \n G29 T"
|
||||
#elif ENABLED(ABL_BI)
|
||||
#define USER_DESC_1 "BIL Commission"
|
||||
#define USER_GCODE_1 "M502 \n M500 \n M501 \n M190 " CommBedTmp" \n M104 S225 \n G28 \n G29 \n M500 \n G28 \n M420 S \n M109 S225 \n G1 X100 Y 100 \n G1 Z0 \n M117 Set Z Offset"
|
||||
|
||||
#define USER_DESC_2 "Prep for Z Adjust"
|
||||
#define USER_GCODE_2 "M190 " CommBedTmp" \n M104 235 \n G28 \n M420 S \n G1 X100 Y 100 \n G1 Z0"
|
||||
#endif
|
||||
#define USER_DESC_5 "Run Mesh Validation"
|
||||
#define USER_GCODE_5 "G26"
|
||||
#endif
|
||||
|
||||
/**
|
||||
@@ -2096,9 +2184,9 @@
|
||||
* Host Prompt Support enables Marlin to use the host for user prompts so
|
||||
* filament runout and other processes can be managed from the host side.
|
||||
*/
|
||||
//#define HOST_ACTION_COMMANDS
|
||||
#define HOST_ACTION_COMMANDS
|
||||
#if ENABLED(HOST_ACTION_COMMANDS)
|
||||
//#define HOST_PROMPT_SUPPORT
|
||||
#define HOST_PROMPT_SUPPORT
|
||||
#endif
|
||||
|
||||
//===========================================================================
|
||||
@@ -2313,7 +2401,7 @@
|
||||
/**
|
||||
* M43 - display pin status, watch pins for changes, watch endstops & toggle LED, Z servo probe test, toggle pins
|
||||
*/
|
||||
//#define PINS_DEBUGGING
|
||||
#define PINS_DEBUGGING
|
||||
|
||||
// Enable Marlin dev mode which adds some special commands
|
||||
//#define MARLIN_DEV_MODE
|
||||
//#define MARLIN_DEV_MODE
|
||||
File diff suppressed because it is too large
Load Diff
@@ -0,0 +1,193 @@
|
||||
#pragma once
|
||||
|
||||
#include "string.h"
|
||||
#include <arduino.h>
|
||||
#include "../ui_api.h"
|
||||
|
||||
/*********************************/
|
||||
#define FHONE (0x5A)
|
||||
#define FHTWO (0xA5)
|
||||
#define TEXTBYTELEN 18
|
||||
#define MaxFileNumber 20// 16
|
||||
|
||||
#define CEIconGrap 12
|
||||
#define FileNum MaxFileNumber
|
||||
#define FileNameLen TEXTBYTELEN
|
||||
#define RTS_UPDATE_INTERVAL 2000
|
||||
#define RTS_UPDATE_VALUE (2*RTS_UPDATE_INTERVAL)
|
||||
|
||||
#define SizeofDatabuf 26
|
||||
|
||||
/*************Register and Variable addr*****************/
|
||||
#define RegAddr_W 0x80
|
||||
#define RegAddr_R 0x81
|
||||
#define VarAddr_W 0x82
|
||||
#define VarAddr_R 0x83
|
||||
#define ExchangePageBase (unsigned long)0x5A010000 //the first page ID. other page = first page ID + relevant num;
|
||||
#define StartSoundSet ((unsigned long)0x060480A0) // 06,start-music; 04, 4 musics; 80, the volume value; 04, return value about music number.
|
||||
#define FONT_EEPROM 90
|
||||
#define AutoLeve_EEPROM 100
|
||||
#define FanOn 255
|
||||
#define FanOff 0
|
||||
|
||||
/*variable addr*/
|
||||
#define ExchangepageAddr 0x0084
|
||||
#define SoundAddr 0x00A0
|
||||
#define StartIcon 0x1000
|
||||
#define FeedrateDisplay 0x1006
|
||||
#define Stopprint 0x1008
|
||||
#define Pauseprint 0x100A
|
||||
#define Resumeprint 0x100C
|
||||
#define PrintscheduleIcon 0x100E
|
||||
#define Timehour 0x1010
|
||||
#define Timemin 0x1012
|
||||
#define IconPrintstatus 0x1014
|
||||
#define Percentage 0x1016
|
||||
#define FanKeyIcon 0x101E
|
||||
|
||||
#define HeatPercentIcon 0x1024
|
||||
|
||||
#define NzBdSet 0x1032
|
||||
#define NozzlePreheat 0x1034
|
||||
#define NozzleTemp 0x1036
|
||||
#define BedPreheat 0x103A
|
||||
#define Bedtemp 0x103C
|
||||
|
||||
#define AutoZeroIcon 0x1042
|
||||
#define AutoLevelIcon 0x1045
|
||||
#define AutoZero 0x1046
|
||||
#define DisplayXaxis 0x1048
|
||||
#define DisplayYaxis 0x104A
|
||||
#define DisplayZaxis 0x104C
|
||||
|
||||
#define FilementUnit1 0x1054
|
||||
#define Exchfilement 0x1056
|
||||
#define FilementUnit2 0x1058
|
||||
|
||||
#define MacVersion 0x1060
|
||||
#define SoftVersion 0x106A
|
||||
#define PrinterSize 0x1074
|
||||
#define CorpWebsite 0x107E
|
||||
#define VolumeIcon 0x108A
|
||||
#define SoundIcon 0x108C
|
||||
#define AutolevelIcon 0x108D
|
||||
#define ExchFlmntIcon 0x108E
|
||||
#define AutolevelVal 0x1100
|
||||
|
||||
#define FilenameIcon 0x1200
|
||||
#define FilenameIcon1 0x1220
|
||||
#define Printfilename 0x2000
|
||||
#define SDFILE_ADDR 0x200A
|
||||
#define FilenamePlay 0x20D2
|
||||
#define FilenameChs 0x20D3
|
||||
#define Choosefilename 0x20D4
|
||||
#define FilenameCount 0x20DE
|
||||
#define FilenameNature 0x6003
|
||||
/************struct**************/
|
||||
|
||||
typedef struct DataBuf
|
||||
{
|
||||
unsigned char len;
|
||||
unsigned char head[2];
|
||||
unsigned char command;
|
||||
unsigned long addr;
|
||||
unsigned long bytelen;
|
||||
unsigned short data[32];
|
||||
unsigned char reserv[4];
|
||||
} DB;
|
||||
|
||||
typedef struct CardRecord
|
||||
{
|
||||
char recordcount;
|
||||
int Filesum;
|
||||
unsigned long addr[FileNum];
|
||||
char Cardshowfilename[FileNum][FileNameLen];
|
||||
char Cardfilename[FileNum][FileNameLen];
|
||||
}CRec;
|
||||
|
||||
class RTSSHOW {
|
||||
public:
|
||||
RTSSHOW();
|
||||
int RTS_RecData();
|
||||
void RTS_SDCardInit(void);
|
||||
void RTS_SDCardUpate(void);
|
||||
int RTS_CheckFilement(int);
|
||||
void RTS_SndData(void);
|
||||
void RTS_SndData(const String &, unsigned long, unsigned char = VarAddr_W);
|
||||
void RTS_SndData(const char[], unsigned long, unsigned char = VarAddr_W);
|
||||
void RTS_SndData(char, unsigned long, unsigned char = VarAddr_W);
|
||||
void RTS_SndData(unsigned char*, unsigned long, unsigned char = VarAddr_W);
|
||||
void RTS_SndData(int, unsigned long, unsigned char = VarAddr_W);
|
||||
void RTS_SndData(float, unsigned long, unsigned char = VarAddr_W);
|
||||
void RTS_SndData(unsigned int,unsigned long, unsigned char = VarAddr_W);
|
||||
void RTS_SndData(long,unsigned long, unsigned char = VarAddr_W);
|
||||
void RTS_SndData(unsigned long,unsigned long, unsigned char = VarAddr_W);
|
||||
void RTS_SDcard_Stop();
|
||||
void RTS_HandleData();
|
||||
void RTS_Init();
|
||||
|
||||
DB recdat;
|
||||
DB snddat;
|
||||
private:
|
||||
unsigned char databuf[SizeofDatabuf];
|
||||
};
|
||||
|
||||
extern RTSSHOW rtscheck;
|
||||
|
||||
|
||||
#ifdef MachineCRX
|
||||
#define Addvalue 2
|
||||
#define PrintChoice_Value (1+Addvalue)
|
||||
#define TempControl_Value (4+Addvalue)
|
||||
#define Setting_Value (8+Addvalue)
|
||||
#define XYZEaxis_Value (12+Addvalue)
|
||||
#define Filement_Value (15+Addvalue)
|
||||
#define Language_Value (18+Addvalue)
|
||||
#define Filename_Value (21+Addvalue)
|
||||
|
||||
enum PROC_COM {Printfile=0,Ajust,Feedrate,PrintChoice=PrintChoice_Value,TempControl=TempControl_Value,ManualSetTemp,Setting=Setting_Value,
|
||||
ReturnBack,Bedlevel,Autohome,XYZEaxis=XYZEaxis_Value,Filement=Filement_Value,LanguageChoice=Language_Value,PwrOffNoF,Volume,Filename=Filename_Value};
|
||||
|
||||
const unsigned long Addrbuf[] = {0x1002, 0x1004, 0x1006, 0x1008, 0x100A, 0x100C, 0x1030, 0x1032, 0x1034, 0x103A, 0x103E,
|
||||
0x1040, 0x1044, 0x1046, 0x1048, 0x104A, 0x104C, 0x1054, 0x1056, 0x1058, 0x105C,
|
||||
0x105F, 0x1088, 0};
|
||||
#else
|
||||
#define Addvalue 3
|
||||
#define PrintChoice_Value (0+Addvalue)
|
||||
#define Zoffset_Value (3+Addvalue)
|
||||
#define Setting_Value (8+Addvalue)
|
||||
#define XYZEaxis_Value (12+Addvalue)
|
||||
#define Filement_Value (15+Addvalue)
|
||||
#define Language_Value (18+Addvalue)
|
||||
#define Filename_Value (22+Addvalue)
|
||||
|
||||
enum PROC_COM {Printfile=0,Ajust,Feedrate,PrintChoice=PrintChoice_Value,Zoffset=Zoffset_Value,TempControl,ManualSetTemp,Setting=Setting_Value,
|
||||
ReturnBack,Bedlevel,Autohome,XYZEaxis=XYZEaxis_Value,Filement=Filement_Value,LanguageChoice=Language_Value,No_Filement,PwrOffNoF,Volume,Filename=Filename_Value};
|
||||
|
||||
const unsigned long Addrbuf[] = {0x1002, 0x1004, 0x1006, 0x1008, 0x100A, 0x100C, 0x1026, 0x1030, 0x1032, 0x1034, 0x103A,
|
||||
0x103E, 0x1040, 0x1044, 0x1046, 0x1048, 0x104A, 0x104C, 0x1054, 0x1056, 0x1058,
|
||||
0x105C, 0x105E, 0x105F, 0x1088, 0};
|
||||
#endif
|
||||
extern void RTSUpdate();
|
||||
extern void RTSInit();
|
||||
|
||||
extern char waitway;
|
||||
extern char CardCheckStatus[2];
|
||||
extern bool InforShowStatus;
|
||||
extern unsigned char LanguageRecbuf;
|
||||
extern unsigned char AxisPagenum;
|
||||
extern bool AutohomeKey;
|
||||
extern bool TPShowStatus;
|
||||
extern bool AutoLevelStatus;
|
||||
extern int Update_Time_Value;
|
||||
extern bool PoweroffContinue;
|
||||
extern char FilementStatus[2];
|
||||
extern char commandbuf[30];
|
||||
|
||||
extern int temphot;
|
||||
extern int tempbed;
|
||||
extern float pause_z;
|
||||
extern char PrintStatue[2];
|
||||
extern char PrinterStatusKey[2];
|
||||
extern const char *injected_commands_P;
|
||||
extern uint8_t progress_bar_percent;
|
||||
@@ -0,0 +1 @@
|
||||
0
|
||||
Reference in New Issue
Block a user