Refactor branch, bump to head

Marlin/Configuration.h

@@ -1,3 +1,102 @@
+// CUSTOMIZE FOR YOUR MACHINE BELOW
+// CUSTOMIZE FOR YOUR MACHINE BELOW
+// CUSTOMIZE FOR YOUR MACHINE BELOW
+// CUSTOMIZE FOR YOUR MACHINE BELOW
+// CUSTOMIZE FOR YOUR MACHINE BELOW
+
+// Enable this is you have a raptor 2.
+// Selects pin file, runout sensor and stock TMC Drivers automatically
+#define RAPTOR2
+
+/**
+ * Enable if you replace the stepper drivers with TMC 2208. Be sure to remove MS3 jumper
+ * underneath the stepper driver! Plug and Play will result in Stealth Chop 2 Mode enabled
+ * Stealthchop with 2208 on E will disabe Linear Advance! Please enable stealthchop if
+ * you require Linear Advance with a TMC2208 on the extruder!
+ * If you have used a UART connection to program the driver to SpreadCycle mode, pease seect that as well
+ */
+//#define X_2208 // TMC2208 or 2209 in Standalone Mode
+//#define X_SpreadCycle
+//#define X_2209_Uart
+//#define Y_2208
+//#define Y_SpreadCycle // Highly recommended as large prints with high mass can cause layer shifts with stealthchop at high speed
+//#define Y_4988  // Some machines shipped with 4988 drivers across the board. Set this if you arent sure what you have and all the drivers look identical
+//#define Y_2209_Uart
+//#define Z_2208 // NOT Recommended! Dual stepper current draw is above the recommended limit for this driver
+//#define Z_SpreadCycle
+//#define Z_4988  // Some machines shipped with 4988 drivers across the board. Set this if you arent sure what you have and all the drivers look identical
+//#define Z_2209_Uart
+//#define E_2208 // Not Recommended! Stealthchop mode faults with linear advance
+//#define E_SpreadCycle
+//#define E_4988
+//#define E_2209_Uart
+
+
+//#define SKR13
+//#define SKR14
+//#define SKR14Turbo
+//#define SKRPRO11
+
+//#define I2C_EEPROM  // use I2C EEPROM on SRK PRO v1.1 e.g AT24C256
+//#define SKR14_PowerLossKit // Bigtreetech power loss kit for SKR14
+
+//#define DualZ // Uses 5th driver on SKR boards as Z2
+
+/**
+ * Enable if you install a KEENOVO AC BED with Solid State Relay
+ */
+#define BED_AC
+
+#define HotendAllMetal
+//#define HotendMosquito
+//#define ExtruderBMG
+
+/**
+ * TM3D E3D Hemera Kit
+ * Swap center 2 wires on extruder connector on Raptor 2
+ *
+ */
+
+#define E3DHemeraExtruder
+
+/**
+ * Enable if you install a filament runout sensor from www.formbotusa.com
+ */
+//#define RunoutSensor
+#define RunoutEncoder
+
+//#define tallVersion // For 700mm version
+
+/**
+ * Enable if you wish to change the auto level strategy to Unified Bed Leveling. Under CUSTOM COMMANDS, run Step 1 and 2 before setting Z Offset
+ */
+//#define UBL //Disabled Firmware Retract and the animated boot screen
+
+//ONLY MAKE CHANGES ABOVE FOR RELIABLE FUNCTION
+//ONLY MAKE CHANGES ABOVE FOR RELIABLE FUNCTION
+//ONLY MAKE CHANGES ABOVE FOR RELIABLE FUNCTION
+//ONLY MAKE CHANGES ABOVE FOR RELIABLE FUNCTION
+//ONLY MAKE CHANGES ABOVE FOR RELIABLE FUNCTION
+
+#if ENABLED(RAPTOR2)
+  #if DISABLED(X_2209_Uart)
+    #define X_2208
+  #endif
+  #if DISABLED(Y_2209_Uart)
+    #define Y_2208
+  #endif
+  #if DISABLED(Z_2209_Uart)
+    #define Z_2208
+  #endif
+  #if DISABLED(E_2209_Uart)
+    #define E_2208
+  #endif
+  #define RunoutSensor
+#endif
+
+#if ANY(SKR13, SKR14, SKR14Turbo, SKRPRO11)
+  #define SKRBoard
+#endif
 /**
  * Marlin 3D Printer Firmware
  * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
@@ -71,8 +170,8 @@
 // @section info
 
 // Author info of this build printed to the host during boot and M115
-#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
-//#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
+#define STRING_CONFIG_H_AUTHOR "Tinymachines3D" // Who made the changes.
+#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
 
 /**
  * *** VENDORS PLEASE READ ***
@@ -89,10 +188,10 @@
 #define SHOW_BOOTSCREEN
 
 // Show the bitmap in Marlin/_Bootscreen.h on startup.
-//#define SHOW_CUSTOM_BOOTSCREEN
+#define SHOW_CUSTOM_BOOTSCREEN
 
 // Show the bitmap in Marlin/_Statusscreen.h on the status screen.
-//#define CUSTOM_STATUS_SCREEN_IMAGE
+#define CUSTOM_STATUS_SCREEN_IMAGE
 
 // @section machine
 
@@ -104,13 +203,19 @@
  *
  * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  */
-#define SERIAL_PORT 0
+#if ANY(SKR13, SKR14, SKR14Turbo, SKRPRO11)
+  #define SERIAL_PORT -1
+#else
+  #define SERIAL_PORT 0
+#endif
 
 /**
  * Select a secondary serial port on the board to use for communication with the host.
  * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  */
-//#define SERIAL_PORT_2 -1
+#if ANY(SKR13, SKR14, SKR14Turbo, SKRPRO11)
+  #define SERIAL_PORT_2 0
+#endif
 
 /**
  * This setting determines the communication speed of the printer.
@@ -128,11 +233,23 @@
 
 // Choose the name from boards.h that matches your setup
 #ifndef MOTHERBOARD
-  #define MOTHERBOARD BOARD_RAMPS_14_EFB
+  #if ENABLED(SKR14Turbo)
+    #define MOTHERBOARD BOARD_BTT_SKR_V1_4_TURBO
+  #elif ENABLED(SKR14)
+    #define MOTHERBOARD BOARD_BTT_SKR_V1_4
+  #elif ENABLED(SKR13)
+    #define MOTHERBOARD BOARD_BTT_SKR_V1_3
+  #elif ENABLED(SKRPRO11)
+    #define MOTHERBOARD BOARD_BTT_SKR_PRO_V1_1
+  #elif ENABLED(RAPTOR2)
+    #define MOTHERBOARD BOARD_FORMBOT_RAPTOR2
+  #else
+    #define MOTHERBOARD BOARD_FORMBOT_RAPTOR
+  #endif
 #endif
 
 // Name displayed in the LCD "Ready" message and Info menu
-//#define CUSTOM_MACHINE_NAME "3D Printer"
+//#define CUSTOM_MACHINE_NAME "TM3D RaPtOr"
 
 // Printer's unique ID, used by some programs to differentiate between machines.
 // Choose your own or use a service like https://www.uuidgenerator.net/version4
@@ -416,7 +533,15 @@
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  */
-#define TEMP_SENSOR_0 1
+#if ENABLED(HotendMosquito)
+  #define TEMP_SENSOR_0 67
+#elif ENABLED(RAPTOR2)
+  #define TEMP_SENSOR_0 61
+#elif ENABLED(E3DHemeraExtruder)
+  #define TEMP_SENSOR_0 5
+#else
+  #define TEMP_SENSOR_0 1
+#endif
 #define TEMP_SENSOR_1 0
 #define TEMP_SENSOR_2 0
 #define TEMP_SENSOR_3 0
@@ -424,7 +549,11 @@
 #define TEMP_SENSOR_5 0
 #define TEMP_SENSOR_6 0
 #define TEMP_SENSOR_7 0
-#define TEMP_SENSOR_BED 0
+#if(ENABLED(BED_AC))
+#define TEMP_SENSOR_BED 11
+#else
+#define TEMP_SENSOR_BED 1
+#endif
 #define TEMP_SENSOR_PROBE 0
 #define TEMP_SENSOR_CHAMBER 0
 
@@ -460,7 +589,13 @@
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 // (Use MINTEMP for thermistor short/failure protection.)
-#define HEATER_0_MAXTEMP 275
+#if ENABLED(HotendMosquito)
+  #define HEATER_0_MAXTEMP 450
+#elif ENABLED(RAPTOR2)
+  #define HEATER_0_MAXTEMP 345
+#else
+  #define HEATER_0_MAXTEMP 305
+#endif
 #define HEATER_1_MAXTEMP 275
 #define HEATER_2_MAXTEMP 275
 #define HEATER_3_MAXTEMP 275
@@ -468,7 +603,11 @@
 #define HEATER_5_MAXTEMP 275
 #define HEATER_6_MAXTEMP 275
 #define HEATER_7_MAXTEMP 275
-#define BED_MAXTEMP      150
+  #if(ENABLED(BED_AC))
+#define BED_MAXTEMP 165
+#else
+  #define BED_MAXTEMP 100
+#endif
 
 //===========================================================================
 //============================= PID Settings ================================
@@ -482,21 +621,37 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
+  #define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  #define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
-  #if ENABLED(PID_PARAMS_PER_HOTEND)
-    // Specify between 1 and HOTENDS values per array.
-    // If fewer than EXTRUDER values are provided, the last element will be repeated.
-    #define DEFAULT_Kp_LIST {  22.20,  20.0 }
-    #define DEFAULT_Ki_LIST {   1.08,   1.0 }
-    #define DEFAULT_Kd_LIST { 114.00, 112.0 }
+
+  // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
+
+  // Ultimaker
+  #if ENABLED(E3DHemeraExtruder)
+    #define  DEFAULT_Kp 21.9
+    #define  DEFAULT_Ki 1.5
+    #define  DEFAULT_Kd 79.88
+  #elif ENABLED(HotendAllMetal)
+    #define  DEFAULT_Kp 21.9
+    #define  DEFAULT_Ki 1.5
+    #define  DEFAULT_Kd 79.88
   #else
-    #define DEFAULT_Kp  22.20
-    #define DEFAULT_Ki   1.08
-    #define DEFAULT_Kd 114.00
+    #define  DEFAULT_Kp 22.2
+    #define  DEFAULT_Ki 1.08
+    #define  DEFAULT_Kd 114
   #endif
+  // MakerGear
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
+
+  // Mendel Parts V9 on 12V
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
+
 #endif // PIDTEMP
 
 //===========================================================================
@@ -516,7 +671,7 @@
  * heater. If your configuration is significantly different than this and you don't understand
  * the issues involved, don't use bed PID until someone else verifies that your hardware works.
  */
-//#define PIDTEMPBED
+#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
@@ -534,9 +689,15 @@
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define DEFAULT_bedKp 10.00
-  #define DEFAULT_bedKi .023
-  #define DEFAULT_bedKd 305.4
+  #if(ENABLED(BED_AC))
+    #define  DEFAULT_bedKp 100.0
+    #define  DEFAULT_bedKi 15.0
+    #define  DEFAULT_bedKd 200.0
+  #else
+    #define DEFAULT_bedKp 10.00
+    #define DEFAULT_bedKi .023
+    #define DEFAULT_bedKd 305.4
+  #endif
 
   //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   //from pidautotune
@@ -621,10 +782,10 @@
 // Almost all printers will be using one per axis. Probes will use one or more of the
 // extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
 #define USE_XMIN_PLUG
-#define USE_YMIN_PLUG
+//#define USE_YMIN_PLUG
 #define USE_ZMIN_PLUG
 //#define USE_XMAX_PLUG
-//#define USE_YMAX_PLUG
+#define USE_YMAX_PLUG
 //#define USE_ZMAX_PLUG
 
 // Enable pullup for all endstops to prevent a floating state
@@ -654,13 +815,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING false // set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -678,16 +839,48 @@
  *          TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE
  * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'L6474', 'POWERSTEP01', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
  */
-//#define X_DRIVER_TYPE  A4988
-//#define Y_DRIVER_TYPE  A4988
-//#define Z_DRIVER_TYPE  A4988
-//#define X2_DRIVER_TYPE A4988
+#if ENABLED(X_2209_Uart)
+  #define X_DRIVER_TYPE  TMC2209
+  #define X2_DRIVER_TYPE TMC2209
+#elif ENABLED(X_2208)
+  #define X_DRIVER_TYPE  TMC2208_STANDALONE
+  #define X2_DRIVER_TYPE TMC2208_STANDALONE
+#else
+  #define X_DRIVER_TYPE  A4988
+  #define X2_DRIVER_TYPE A4988
+#endif
+#if ENABLED(Y_2209_Uart)
+  #define Y_DRIVER_TYPE  TMC2209
+#elif ENABLED(Y_2208)
+  #define Y_DRIVER_TYPE  TMC2208_STANDALONE
+#elif ENABLED(Y_4988)
+  #define Y_DRIVER_TYPE  A4988
+#else
+  #define Y_DRIVER_TYPE  DRV8825
+#endif
+#if ENABLED(Z_2209_Uart)
+  #define Z_DRIVER_TYPE  TMC2209
+#elif ENABLED(Z_2208)
+  #define Z_DRIVER_TYPE  TMC2208_STANDALONE
+#elif ENABLED(Z_4988)
+  #define Z_DRIVER_TYPE  A4988
+#else
+  #define Z_DRIVER_TYPE  DRV8825
+#endif
 //#define Y2_DRIVER_TYPE A4988
 //#define Z2_DRIVER_TYPE A4988
 //#define Z3_DRIVER_TYPE A4988
 //#define Z4_DRIVER_TYPE A4988
-//#define E0_DRIVER_TYPE A4988
-//#define E1_DRIVER_TYPE A4988
+#if ENABLED(E_2209_Uart)
+  #define E0_DRIVER_TYPE TMC2209
+  #define E1_DRIVER_TYPE TMC2209
+#elif ENABLED(E_2208)
+  #define E0_DRIVER_TYPE TMC2208_STANDALONE
+  #define E1_DRIVER_TYPE TMC2208_STANDALONE
+#else
+  #define E0_DRIVER_TYPE  DRV8825
+  #define E1_DRIVER_TYPE DRV8825
+#endif
 //#define E2_DRIVER_TYPE A4988
 //#define E3_DRIVER_TYPE A4988
 //#define E4_DRIVER_TYPE A4988
@@ -741,14 +934,40 @@
  * Override with M92
  *                                      X, Y, Z, E0 [, E1[, E2...]]
  */
-#define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 80, 4000, 500 }
+#if ENABLED(E3DHemeraExtruder)
+  #if ANY(E_2208, E_4988, E_2209_Uart)
+    #define E_STEPSMM 409
+  #else
+    #define E_STEPSMM 818
+  #endif
+#else
+  #if ANY(E_2208, E_4988, E_2209_Uart)
+    #define E_STEPSMM 96
+  #else
+    #define E_STEPSMM 192
+  #endif
+#endif
+
+#if ANY(Y_2208, Y_4988, Y_2209_Uart)
+  #define Y_STEPSMM 80
+#else
+  #define Y_STEPSMM 160
+#endif
+
+#if ANY(Z_2208, Z_4988, Z_2209_Uart)
+  #define Z_STEPSMM 800
+#else
+  #define Z_STEPSMM 1600
+#endif
+
+#define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, Y_STEPSMM, Z_STEPSMM, E_STEPSMM }
 
 /**
  * Default Max Feed Rate (mm/s)
  * Override with M203
  *                                      X, Y, Z, E0 [, E1[, E2...]]
  */
-#define DEFAULT_MAX_FEEDRATE          { 300, 300, 5, 25 }
+#define DEFAULT_MAX_FEEDRATE          { 300, 150, 5, 70 }
 
 //#define LIMITED_MAX_FR_EDITING        // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
 #if ENABLED(LIMITED_MAX_FR_EDITING)
@@ -761,7 +980,26 @@
  * Override with M201
  *                                      X, Y, Z, E0 [, E1[, E2...]]
  */
-#define DEFAULT_MAX_ACCELERATION      { 3000, 3000, 100, 10000 }
+ #if(ENABLED(X_2208))
+  #if(ENABLED(X_SpreadCycle))
+    #define x_accel 750
+  #else
+    #define x_accel 500
+  #endif
+ #else
+  #define x_accel 750
+ #endif
+
+  #if(ENABLED(Y_2208))
+  #if(ENABLED(Y_SpreadCycle))
+    #define y_accel 500
+  #else
+    #define y_accel 300
+  #endif
+ #else
+  #define y_accel 500
+ #endif
+#define DEFAULT_MAX_ACCELERATION      { x_accel, y_accel, 400, 4000 }
 
 //#define LIMITED_MAX_ACCEL_EDITING     // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
 #if ENABLED(LIMITED_MAX_ACCEL_EDITING)
@@ -776,9 +1014,9 @@
  *   M204 R    Retract Acceleration
  *   M204 T    Travel Acceleration
  */
-#define DEFAULT_ACCELERATION          3000    // X, Y, Z and E acceleration for printing moves
-#define DEFAULT_RETRACT_ACCELERATION  3000    // E acceleration for retracts
-#define DEFAULT_TRAVEL_ACCELERATION   3000    // X, Y, Z acceleration for travel (non printing) moves
+#define DEFAULT_ACCELERATION          500    // X, Y, Z and E acceleration for printing moves
+#define DEFAULT_RETRACT_ACCELERATION  500    // E acceleration for retracts
+#define DEFAULT_TRAVEL_ACCELERATION   500    // X, Y, Z acceleration for travel (non printing) moves
 
 /**
  * Default Jerk limits (mm/s)
@@ -788,10 +1026,10 @@
  * When changing speed and direction, if the difference is less than the
  * value set here, it may happen instantaneously.
  */
-//#define CLASSIC_JERK
+#define CLASSIC_JERK
 #if ENABLED(CLASSIC_JERK)
-  #define DEFAULT_XJERK 10.0
-  #define DEFAULT_YJERK 10.0
+  #define DEFAULT_XJERK 15.0
+  #define DEFAULT_YJERK 7.0
   #define DEFAULT_ZJERK  0.3
 
   //#define TRAVEL_EXTRA_XYJERK 0.0     // Additional jerk allowance for all travel moves
@@ -825,7 +1063,7 @@
  *
  * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained
  */
-//#define S_CURVE_ACCELERATION
+#define S_CURVE_ACCELERATION
 
 //===========================================================================
 //============================= Z Probe Options =============================
@@ -900,7 +1138,7 @@
 /**
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
-//#define BLTOUCH
+#define BLTOUCH
 
 /**
  * Pressure sensor with a BLTouch-like interface
@@ -987,20 +1225,27 @@
  *     |    [-]    |
  *     O-- FRONT --+
  */
-#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
+#if ENABLED(E3DHemeraExtruder)
+  #define NOZZLE_TO_PROBE_OFFSET { -38, 0, 0 }
+#elif ENABLED(HotendMosquito)
+  #define NOZZLE_TO_PROBE_OFFSET { 35, 10, 0 }
+#else
+  #define NOZZLE_TO_PROBE_OFFSET { -22, 0, 0 }
+#endif
+
 
 // Most probes should stay away from the edges of the bed, but
 // with NOZZLE_AS_PROBE this can be negative for a wider probing area.
-#define PROBING_MARGIN 10
+#define PROBING_MARGIN 8
 
-// X and Y axis travel speed (mm/min) between probes
-#define XY_PROBE_SPEED (133*60)
+// X and Y axis travel speed (mm/m) between probes
+#define XY_PROBE_SPEED 10000
 
-// Feedrate (mm/min) for the first approach when double-probing (MULTIPLE_PROBING == 2)
-#define Z_PROBE_SPEED_FAST HOMING_FEEDRATE_Z
+// Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2)
+#define Z_PROBE_SPEED_FAST (HOMING_FEEDRATE_Z * 2)
 
-// Feedrate (mm/min) for the "accurate" probe of each point
-#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)
+// Feedrate (mm/m) for the "accurate" probe of each point
+#define Z_PROBE_SPEED_SLOW Z_PROBE_SPEED_FAST
 
 /**
  * Multiple Probing
@@ -1011,7 +1256,7 @@
  * A total of 2 does fast/slow probes with a weighted average.
  * A total of 3 or more adds more slow probes, taking the average.
  */
-//#define MULTIPLE_PROBING 2
+#define MULTIPLE_PROBING 2
 //#define EXTRA_PROBING    1
 
 /**
@@ -1028,16 +1273,16 @@
  * Example: `M851 Z-5` with a CLEARANCE of 4  =>  9mm from bed to nozzle.
  *     But: `M851 Z+1` with a CLEARANCE of 2  =>  2mm from bed to nozzle.
  */
-#define Z_CLEARANCE_DEPLOY_PROBE   10 // Z Clearance for Deploy/Stow
+#define Z_CLEARANCE_DEPLOY_PROBE   5 // Z Clearance for Deploy/Stow
 #define Z_CLEARANCE_BETWEEN_PROBES  5 // Z Clearance between probe points
 #define Z_CLEARANCE_MULTI_PROBE     5 // Z Clearance between multiple probes
-//#define Z_AFTER_PROBING           5 // Z position after probing is done
+#define Z_AFTER_PROBING           5 // Z position after probing is done
 
-#define Z_PROBE_LOW_POINT          -2 // Farthest distance below the trigger-point to go before stopping
+#define Z_PROBE_LOW_POINT          -4 // Farthest distance below the trigger-point to go before stopping
 
 // For M851 give a range for adjusting the Z probe offset
-#define Z_PROBE_OFFSET_RANGE_MIN -20
-#define Z_PROBE_OFFSET_RANGE_MAX 20
+#define Z_PROBE_OFFSET_RANGE_MIN -9
+#define Z_PROBE_OFFSET_RANGE_MAX 9
 
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
@@ -1087,15 +1332,33 @@
 // @section machine
 
 // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
-#define INVERT_X_DIR false
-#define INVERT_Y_DIR true
-#define INVERT_Z_DIR false
+ #if ANY(X_2208, X_2209_Uart)
+  #define INVERT_X_DIR true
+#else
+  #define INVERT_X_DIR false
+#endif
+#if ANY(Y_2208, Y_2209_Uart)
+  #define INVERT_Y_DIR true
+#else
+  #define INVERT_Y_DIR false
+#endif
+#if ANY(Z_2208, Z_2209_Uart)
+  #define INVERT_Z_DIR false
+#else
+  #define INVERT_Z_DIR true
+#endif
+
 
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.
-#define INVERT_E0_DIR false
-#define INVERT_E1_DIR false
+#if (ANY(E_2208, E_2209_Uart) && NONE(HotendMosquito, ExtruderBMG)) || (ANY(HotendMosquito, ExtruderBMG) && NONE(E_2208, E_2209_Uart))
+  #define INVERT_E0_DIR false
+  #define INVERT_E1_DIR true
+#else
+  #define INVERT_E0_DIR true
+  #define INVERT_E1_DIR false
+#endif
 #define INVERT_E2_DIR false
 #define INVERT_E3_DIR false
 #define INVERT_E4_DIR false
@@ -1109,7 +1372,7 @@
 
 //#define UNKNOWN_Z_NO_RAISE      // Don't raise Z (lower the bed) if Z is "unknown." For beds that fall when Z is powered off.
 
-//#define Z_HOMING_HEIGHT  4      // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
+#define Z_HOMING_HEIGHT  4      // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                                   // Be sure to have this much clearance over your Z_MAX_POS to prevent grinding.
 
 //#define Z_AFTER_HOMING  10      // (mm) Height to move to after homing Z
@@ -1117,14 +1380,18 @@
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1
-#define Y_HOME_DIR -1
+#define Y_HOME_DIR 1
 #define Z_HOME_DIR -1
 
 // @section machine
 
 // The size of the print bed
-#define X_BED_SIZE 200
-#define Y_BED_SIZE 200
+#if ANY(RAPTOR2, E3DHemeraExtruder)
+  #define X_BED_SIZE 385
+#else
+  #define X_BED_SIZE 400
+#endif
+#define Y_BED_SIZE 400
 
 // Travel limits (mm) after homing, corresponding to endstop positions.
 #define X_MIN_POS 0
@@ -1132,7 +1399,11 @@
 #define Z_MIN_POS 0
 #define X_MAX_POS X_BED_SIZE
 #define Y_MAX_POS Y_BED_SIZE
-#define Z_MAX_POS 200
+#if(ENABLED(tallVersion))
+  #define Z_MAX_POS 700
+#else
+  #define Z_MAX_POS 500
+#endif
 
 /**
  * Software Endstops
@@ -1160,7 +1431,7 @@
 #endif
 
 #if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS)
-  //#define SOFT_ENDSTOPS_MENU_ITEM  // Enable/Disable software endstops from the LCD
+  #define SOFT_ENDSTOPS_MENU_ITEM  // Enable/Disable software endstops from the LCD
 #endif
 
 /**
@@ -1170,13 +1441,20 @@
  * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
  * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
  */
-//#define FILAMENT_RUNOUT_SENSOR
+ #if ANY(RunoutSensor, RunoutEncoder)
+  #define FILAMENT_RUNOUT_SENSOR
+#endif
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define NUM_RUNOUT_SENSORS   1     // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
   #define FIL_RUNOUT_ENABLED_DEFAULT true // Enable the sensor on startup. Override with M412 followed by M500.
-  #define NUM_RUNOUT_SENSORS   1          // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
-  #define FIL_RUNOUT_STATE     LOW        // Pin state indicating that filament is NOT present.
-  #define FIL_RUNOUT_PULLUP               // Use internal pullup for filament runout pins.
-  //#define FIL_RUNOUT_PULLDOWN           // Use internal pulldown for filament runout pins.
+  #if NONE(RAPTOR2, SKRBoard)
+    #define FIL_RUNOUT_PIN 57
+    #define FIL_RUNOUT_STATE     HIGH // set to true to invert the logic of the sensor.
+  #else
+    #define FIL_RUNOUT_STATE     LOW // set to true to invert the logic of the sensor.
+  #endif
+  #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
+  //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
 
   // Set one or more commands to execute on filament runout.
   // (After 'M412 H' Marlin will ask the host to handle the process.)
@@ -1185,13 +1463,19 @@
   // After a runout is detected, continue printing this length of filament
   // before executing the runout script. Useful for a sensor at the end of
   // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead.
-  //#define FILAMENT_RUNOUT_DISTANCE_MM 25
+  #if ENABLED(RunoutEncoder)
+    #define FILAMENT_RUNOUT_DISTANCE_MM 15
+  #else
+    #define FILAMENT_RUNOUT_DISTANCE_MM 5
+  #endif
 
   #ifdef FILAMENT_RUNOUT_DISTANCE_MM
     // Enable this option to use an encoder disc that toggles the runout pin
     // as the filament moves. (Be sure to set FILAMENT_RUNOUT_DISTANCE_MM
     // large enough to avoid false positives.)
-    //#define FILAMENT_MOTION_SENSOR
+    #if ENABLED(RunoutEncoder)
+      #define FILAMENT_MOTION_SENSOR
+    #endif
   #endif
 #endif
 
@@ -1235,15 +1519,19 @@
  */
 //#define AUTO_BED_LEVELING_3POINT
 //#define AUTO_BED_LEVELING_LINEAR
-//#define AUTO_BED_LEVELING_BILINEAR
-//#define AUTO_BED_LEVELING_UBL
+#if(ENABLED(UBL))
+  #define AUTO_BED_LEVELING_UBL
+#else
+  #define AUTO_BED_LEVELING_BILINEAR
+#endif
+
 //#define MESH_BED_LEVELING
 
 /**
  * Normally G28 leaves leveling disabled on completion. Enable
  * this option to have G28 restore the prior leveling state.
  */
-//#define RESTORE_LEVELING_AFTER_G28
+#define RESTORE_LEVELING_AFTER_G28
 
 /**
  * Enable detailed logging of G28, G29, M48, etc.
@@ -1267,7 +1555,7 @@
   /**
    * Enable the G26 Mesh Validation Pattern tool.
    */
-  //#define G26_MESH_VALIDATION
+  #define G26_MESH_VALIDATION
   #if ENABLED(G26_MESH_VALIDATION)
     #define MESH_TEST_NOZZLE_SIZE    0.4  // (mm) Diameter of primary nozzle.
     #define MESH_TEST_LAYER_HEIGHT   0.2  // (mm) Default layer height for the G26 Mesh Validation Tool.
@@ -1282,7 +1570,7 @@
 #if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR)
 
   // Set the number of grid points per dimension.
-  #define GRID_MAX_POINTS_X 3
+  #define GRID_MAX_POINTS_X 11
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
 
   // Probe along the Y axis, advancing X after each column
@@ -1292,7 +1580,7 @@
 
     // Beyond the probed grid, continue the implied tilt?
     // Default is to maintain the height of the nearest edge.
-    //#define EXTRAPOLATE_BEYOND_GRID
+    #define EXTRAPOLATE_BEYOND_GRID
 
     //
     // Experimental Subdivision of the grid by Catmull-Rom method.
@@ -1312,16 +1600,16 @@
   //========================= Unified Bed Leveling ============================
   //===========================================================================
 
-  //#define MESH_EDIT_GFX_OVERLAY   // Display a graphics overlay while editing the mesh
+  #define MESH_EDIT_GFX_OVERLAY      // Display a graphics overlay while editing the mesh
 
-  #define MESH_INSET 1              // Set Mesh bounds as an inset region of the bed
-  #define GRID_MAX_POINTS_X 10      // Don't use more than 15 points per axis, implementation limited.
+  #define MESH_INSET 5              // Set Mesh bounds as an inset region of the bed
+  #define GRID_MAX_POINTS_X 15      // Don't use more than 15 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
 
   #define UBL_MESH_EDIT_MOVES_Z     // Sophisticated users prefer no movement of nozzle
   #define UBL_SAVE_ACTIVE_ON_M500   // Save the currently active mesh in the current slot on M500
 
-  //#define UBL_Z_RAISE_WHEN_OFF_MESH 2.5 // When the nozzle is off the mesh, this value is used
+  #define UBL_Z_RAISE_WHEN_OFF_MESH 0.0 // When the nozzle is off the mesh, this value is used
                                           // as the Z-Height correction value.
 
 #elif ENABLED(MESH_BED_LEVELING)
@@ -1351,13 +1639,13 @@
 #endif
 
 // Add a menu item to move between bed corners for manual bed adjustment
-//#define LEVEL_BED_CORNERS
+#define LEVEL_BED_CORNERS
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets
   #define LEVEL_CORNERS_HEIGHT      0.0   // (mm) Z height of nozzle at leveling points
   #define LEVEL_CORNERS_Z_HOP       4.0   // (mm) Z height of nozzle between leveling points
-  //#define LEVEL_CENTER_TOO              // Move to the center after the last corner
+  #define LEVEL_CENTER_TOO              // Move to the center after the last corner
 #endif
 
 /**
@@ -1386,7 +1674,7 @@
 // - Move the Z probe (or nozzle) to a defined XY point before Z Homing.
 // - Prevent Z homing when the Z probe is outside bed area.
 //
-//#define Z_SAFE_HOMING
+#define Z_SAFE_HOMING
 
 #if ENABLED(Z_SAFE_HOMING)
   #define Z_SAFE_HOMING_X_POINT X_CENTER  // X point for Z homing
@@ -1472,12 +1760,12 @@
  *   M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
  *   M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
  */
-//#define EEPROM_SETTINGS     // Persistent storage with M500 and M501
+#define EEPROM_SETTINGS     // Persistent storage with M500 and M501
 //#define DISABLE_M503        // Saves ~2700 bytes of PROGMEM. Disable for release!
 #define EEPROM_CHITCHAT       // Give feedback on EEPROM commands. Disable to save PROGMEM.
 #define EEPROM_BOOT_SILENT    // Keep M503 quiet and only give errors during first load
 #if ENABLED(EEPROM_SETTINGS)
-  //#define EEPROM_AUTO_INIT  // Init EEPROM automatically on any errors.
+  #define EEPROM_AUTO_INIT  // Init EEPROM automatically on any errors.
 #endif
 
 //
@@ -1524,11 +1812,11 @@
  *    P1  Raise the nozzle always to Z-park height.
  *    P2  Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
  */
-//#define NOZZLE_PARK_FEATURE
+#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
   // Specify a park position as { X, Y, Z_raise }
-  #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
+  #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MIN_POS + 10), 5 }
   //#define NOZZLE_PARK_X_ONLY          // X move only is required to park
   //#define NOZZLE_PARK_Y_ONLY          // Y move only is required to park
   #define NOZZLE_PARK_Z_RAISE_MIN   2   // (mm) Always raise Z by at least this distance
@@ -1727,7 +2015,7 @@
  * you must uncomment the following option or it won't work.
  *
  */
-//#define SDSUPPORT
+#define SDSUPPORT
 
 /**
  * SD CARD: SPI SPEED
@@ -1807,7 +2095,7 @@
 //
 // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
 //
-//#define INDIVIDUAL_AXIS_HOMING_MENU
+#define INDIVIDUAL_AXIS_HOMING_MENU
 
 //
 // SPEAKER/BUZZER
@@ -1815,7 +2103,7 @@
 // If you have a speaker that can produce tones, enable it here.
 // By default Marlin assumes you have a buzzer with a fixed frequency.
 //
-//#define SPEAKER
+#define SPEAKER
 
 //
 // The duration and frequency for the UI feedback sound.
@@ -1980,7 +2268,7 @@
 // RepRapDiscount FULL GRAPHIC Smart Controller
 // https://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
 //
-//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
+#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
 
 //
 // ReprapWorld Graphical LCD

Marlin/Configuration_adv.h

@@ -162,12 +162,12 @@
  * THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
  */
 #if ENABLED(THERMAL_PROTECTION_HOTENDS)
-  #define THERMAL_PROTECTION_PERIOD 40        // Seconds
-  #define THERMAL_PROTECTION_HYSTERESIS 4     // Degrees Celsius
+  #define THERMAL_PROTECTION_PERIOD 30        // Seconds
+  #define THERMAL_PROTECTION_HYSTERESIS 15     // Degrees Celsius
 
-  //#define ADAPTIVE_FAN_SLOWING              // Slow part cooling fan if temperature drops
+  #define ADAPTIVE_FAN_SLOWING              // Slow part cooling fan if temperature drops
   #if BOTH(ADAPTIVE_FAN_SLOWING, PIDTEMP)
-    //#define NO_FAN_SLOWING_IN_PID_TUNING    // Don't slow fan speed during M303
+    #define NO_FAN_SLOWING_IN_PID_TUNING    // Don't slow fan speed during M303
   #endif
 
   /**
@@ -182,7 +182,7 @@
    * and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set
    * below 2.
    */
-  #define WATCH_TEMP_PERIOD 20                // Seconds
+  #define WATCH_TEMP_PERIOD 210               // Seconds
   #define WATCH_TEMP_INCREASE 2               // Degrees Celsius
 #endif
 
@@ -190,28 +190,28 @@
  * Thermal Protection parameters for the bed are just as above for hotends.
  */
 #if ENABLED(THERMAL_PROTECTION_BED)
-  #define THERMAL_PROTECTION_BED_PERIOD        20 // Seconds
-  #define THERMAL_PROTECTION_BED_HYSTERESIS     2 // Degrees Celsius
+  #define THERMAL_PROTECTION_BED_PERIOD 300    // Seconds
+  #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
 
   /**
    * As described above, except for the bed (M140/M190/M303).
    */
-  #define WATCH_BED_TEMP_PERIOD                60 // Seconds
-  #define WATCH_BED_TEMP_INCREASE               2 // Degrees Celsius
+  #define WATCH_BED_TEMP_PERIOD 60                // Seconds
+  #define WATCH_BED_TEMP_INCREASE 2               // Degrees Celsius
 #endif
 
 /**
  * Thermal Protection parameters for the heated chamber.
  */
 #if ENABLED(THERMAL_PROTECTION_CHAMBER)
-  #define THERMAL_PROTECTION_CHAMBER_PERIOD    20 // Seconds
+  #define THERMAL_PROTECTION_CHAMBER_PERIOD 20    // Seconds
   #define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
 
   /**
    * Heated chamber watch settings (M141/M191).
    */
-  #define WATCH_CHAMBER_TEMP_PERIOD            60 // Seconds
-  #define WATCH_CHAMBER_TEMP_INCREASE           2 // Degrees Celsius
+  #define WATCH_CHAMBER_TEMP_PERIOD 60            // Seconds
+  #define WATCH_CHAMBER_TEMP_INCREASE 2           // Degrees Celsius
 #endif
 
 #if ENABLED(PIDTEMP)
@@ -347,7 +347,7 @@
  * Hotend Idle Timeout
  * Prevent filament in the nozzle from charring and causing a critical jam.
  */
-//#define HOTEND_IDLE_TIMEOUT
+#define HOTEND_IDLE_TIMEOUT
 #if ENABLED(HOTEND_IDLE_TIMEOUT)
   #define HOTEND_IDLE_TIMEOUT_SEC (5*60)    // (seconds) Time without extruder movement to trigger protection
   #define HOTEND_IDLE_MIN_TRIGGER   180     // (°C) Minimum temperature to enable hotend protection
@@ -389,7 +389,7 @@
 // When first starting the main fan, run it at full speed for the
 // given number of milliseconds.  This gets the fan spinning reliably
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
-//#define FAN_KICKSTART_TIME 100
+#define FAN_KICKSTART_TIME 100
 
 // Some coolers may require a non-zero "off" state.
 //#define FAN_OFF_PWM  1
@@ -450,7 +450,11 @@
  * Multiple extruders can be assigned to the same pin in which case
  * the fan will turn on when any selected extruder is above the threshold.
  */
-#define E0_AUTO_FAN_PIN -1
+#if ENABLED(RAPTOR2) && DISABLED(SKRBoard)
+  #define E0_AUTO_FAN_PIN 9
+#else
+  #define E0_AUTO_FAN_PIN -1
+#endif
 #define E1_AUTO_FAN_PIN -1
 #define E2_AUTO_FAN_PIN -1
 #define E3_AUTO_FAN_PIN -1
@@ -479,16 +483,18 @@
 /**
  * M355 Case Light on-off / brightness
  */
-//#define CASE_LIGHT_ENABLE
+#if DISABLED(SKRBoard)
+  #define CASE_LIGHT_ENABLE
+#endif
 #if ENABLED(CASE_LIGHT_ENABLE)
-  //#define CASE_LIGHT_PIN 4                  // Override the default pin if needed
+  #define CASE_LIGHT_PIN 5                  // Override the default pin if needed
   #define INVERT_CASE_LIGHT false             // Set true if Case Light is ON when pin is LOW
   #define CASE_LIGHT_DEFAULT_ON true          // Set default power-up state on
-  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // Set default power-up brightness (0-255, requires PWM pin)
+  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 255   // Set default power-up brightness (0-255, requires PWM pin)
   //#define CASE_LIGHT_MAX_PWM 128            // Limit pwm
-  //#define CASE_LIGHT_MENU                   // Add Case Light options to the LCD menu
-  //#define CASE_LIGHT_NO_BRIGHTNESS          // Disable brightness control. Enable for non-PWM lighting.
-  //#define CASE_LIGHT_USE_NEOPIXEL           // Use NeoPixel LED as case light, requires NEOPIXEL_LED.
+  #define CASE_LIGHT_MENU                   // Add Case Light options to the LCD menu
+  #define CASE_LIGHT_NO_BRIGHTNESS          // Disable brightness control. Enable for non-PWM lighting.
+  //#define CASE_LIGHT_USE_NEOPIXEL           // Use Neopixel LED as case light, requires NEOPIXEL_LED.
   #if ENABLED(CASE_LIGHT_USE_NEOPIXEL)
     #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White }
   #endif
@@ -549,7 +555,11 @@
 //
 // For Z set the number of stepper drivers
 //
-#define NUM_Z_STEPPER_DRIVERS 1   // (1-4) Z options change based on how many
+#if ENABLED(SKRBoard) && ENABLED(DualZ)
+  #define NUM_Z_STEPPER_DRIVERS 2   // (1-4) Z options change based on how many
+#else
+  #define NUM_Z_STEPPER_DRIVERS 1   // (1-4) Z options change based on how many
+#endif
 
 #if NUM_Z_STEPPER_DRIVERS > 1
   //#define Z_MULTI_ENDSTOPS
@@ -634,7 +644,7 @@
 
 //#define HOMING_BACKOFF_POST_MM { 2, 2, 2 }  // (mm) Backoff from endstops after homing
 
-//#define QUICK_HOME                          // If G28 contains XY do a diagonal move first
+#define QUICK_HOME                          // If G28 contains XY do a diagonal move first
 //#define HOME_Y_BEFORE_X                     // If G28 contains XY home Y before X
 //#define CODEPENDENT_XY_HOMING               // If X/Y can't home without homing Y/X first
 
@@ -700,7 +710,7 @@
    * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
    * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
    */
-  //#define BLTOUCH_HS_MODE
+  #define BLTOUCH_HS_MODE
 
   // Safety: Enable voltage mode settings in the LCD menu.
   //#define BLTOUCH_LCD_VOLTAGE_MENU
@@ -713,7 +723,9 @@
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.
  */
-//#define Z_STEPPER_AUTO_ALIGN
+#if ENABLED(SKRBoard) && ENABLED(DualZ)
+  #define Z_STEPPER_AUTO_ALIGN
+#endif
 #if ENABLED(Z_STEPPER_AUTO_ALIGN)
   // Define probe X and Y positions for Z1, Z2 [, Z3 [, Z4]]
   // If not defined, probe limits will be used.
@@ -824,7 +836,7 @@
 // If the Nozzle or Bed falls when the Z stepper is disabled, set its resting position here.
 //#define Z_AFTER_DEACTIVATE Z_HOME_POS
 
-//#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
+#define HOME_AFTER_DEACTIVATE  // Require rehoming after steppers are deactivated
 
 // Default Minimum Feedrates for printing and travel moves
 #define DEFAULT_MINIMUMFEEDRATE       0.0     // (mm/s) Minimum feedrate. Set with M205 S.
@@ -860,7 +872,8 @@
 // Backlash Compensation
 // Adds extra movement to axes on direction-changes to account for backlash.
 //
-//#define BACKLASH_COMPENSATION
+
+#define BACKLASH_COMPENSATION
 #if ENABLED(BACKLASH_COMPENSATION)
   // Define values for backlash distance and correction.
   // If BACKLASH_GCODE is enabled these values are the defaults.
@@ -872,7 +885,7 @@
   //#define BACKLASH_SMOOTHING_MM 3 // (mm)
 
   // Add runtime configuration and tuning of backlash values (M425)
-  //#define BACKLASH_GCODE
+  #define BACKLASH_GCODE
 
   #if ENABLED(BACKLASH_GCODE)
     // Measure the Z backlash when probing (G29) and set with "M425 Z"
@@ -951,7 +964,9 @@
  * vibration and surface artifacts. The algorithm adapts to provide the best possible step smoothing at the
  * lowest stepping frequencies.
  */
-//#define ADAPTIVE_STEP_SMOOTHING
+#if ENABLED(SKRBoard)
+  #define ADAPTIVE_STEP_SMOOTHING
+#endif
 
 /**
  * Custom Microstepping
@@ -1088,22 +1103,22 @@
 #endif // HAS_LCD_MENU
 
 // Scroll a longer status message into view
-//#define STATUS_MESSAGE_SCROLLING
+#define STATUS_MESSAGE_SCROLLING
 
 // On the Info Screen, display XY with one decimal place when possible
-//#define LCD_DECIMAL_SMALL_XY
+#define LCD_DECIMAL_SMALL_XY
 
 // The timeout (in ms) to return to the status screen from sub-menus
-//#define LCD_TIMEOUT_TO_STATUS 15000
+#define LCD_TIMEOUT_TO_STATUS 15000
 
 // Add an 'M73' G-code to set the current percentage
-//#define LCD_SET_PROGRESS_MANUALLY
+#define LCD_SET_PROGRESS_MANUALLY
 
 // Show the E position (filament used) during printing
 //#define LCD_SHOW_E_TOTAL
 
 #if ENABLED(SHOW_BOOTSCREEN)
-  #define BOOTSCREEN_TIMEOUT 4000        // (ms) Total Duration to display the boot screen(s)
+  #define BOOTSCREEN_TIMEOUT 2000        // (ms) Total Duration to display the boot screen(s)
 #endif
 
 #if EITHER(SDSUPPORT, LCD_SET_PROGRESS_MANUALLY) && (HAS_GRAPHICAL_LCD || HAS_CHARACTER_LCD)
@@ -1133,7 +1148,7 @@
 
   // The standard SD detect circuit reads LOW when media is inserted and HIGH when empty.
   // Enable this option and set to HIGH if your SD cards are incorrectly detected.
-  //#define SD_DETECT_STATE HIGH
+  #define SD_DETECT_STATE HIGH
 
   //#define SDCARD_READONLY                 // Read-only SD card (to save over 2K of flash)
 
@@ -1164,13 +1179,15 @@
    * an option on the LCD screen to continue the print from the last-known
    * point in the file.
    */
-  //#define POWER_LOSS_RECOVERY
+  #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT   false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
     //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
     //#define POWER_LOSS_ZRAISE       2 // (mm) Z axis raise on resume (on power loss with UPS)
-    //#define POWER_LOSS_PIN         44 // Pin to detect power loss. Set to -1 to disable default pin on boards without module.
-    //#define POWER_LOSS_STATE     HIGH // State of pin indicating power loss
+    #if ENABLED(SKRBoard)
+      #define POWER_LOSS_PIN         -1 // Pin to detect power loss. Set to -1 to disable default pin on boards without module.
+      #define POWER_LOSS_STATE     LOW // State of pin indicating power loss
+    #endif
     //#define POWER_LOSS_PULL           // Set pullup / pulldown as appropriate
     //#define POWER_LOSS_PURGE_LEN   20 // (mm) Length of filament to purge on resume
     //#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
@@ -1219,10 +1236,10 @@
   #endif
 
   // This allows hosts to request long names for files and folders with M33
-  //#define LONG_FILENAME_HOST_SUPPORT
+  #define LONG_FILENAME_HOST_SUPPORT
 
   // Enable this option to scroll long filenames in the SD card menu
-  //#define SCROLL_LONG_FILENAMES
+  #define SCROLL_LONG_FILENAMES
 
   // Leave the heaters on after Stop Print (not recommended!)
   //#define SD_ABORT_NO_COOLDOWN
@@ -1244,7 +1261,7 @@
   /**
    * Auto-report SdCard status with M27 S<seconds>
    */
-  //#define AUTO_REPORT_SD_STATUS
+  #define AUTO_REPORT_SD_STATUS
 
   /**
    * Support for USB thumb drives using an Arduino USB Host Shield or
@@ -1330,7 +1347,7 @@
  */
 #if HAS_GRAPHICAL_LCD
   // Show SD percentage next to the progress bar
-  //#define DOGM_SD_PERCENT
+  #define DOGM_SD_PERCENT
 
   // Save many cycles by drawing a hollow frame or no frame on the Info Screen
   //#define XYZ_NO_FRAME
@@ -1341,7 +1358,7 @@
 
   // A bigger font is available for edit items. Costs 3120 bytes of PROGMEM.
   // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
-  //#define USE_BIG_EDIT_FONT
+  #define USE_BIG_EDIT_FONT
 
   // A smaller font may be used on the Info Screen. Costs 2300 bytes of PROGMEM.
   // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
@@ -1389,13 +1406,18 @@
   //#define STATUS_ALT_FAN_BITMAP     // Use the alternative fan bitmap
   //#define STATUS_FAN_FRAMES 3       // :[0,1,2,3,4] Number of fan animation frames
   //#define STATUS_HEAT_PERCENT       // Show heating in a progress bar
-  //#define BOOT_MARLIN_LOGO_SMALL    // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash)
-  //#define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~‭3260 (or ~940) bytes of PROGMEM.
+  #if ENABLED(UBL) && DISABLED(SKRBoard)
+    #define BOOT_MARLIN_LOGO_SMALL    // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash)
+  #else
+    #define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~‭3260 (or ~940) bytes of PROGMEM.
+  #endif
 
   // Frivolous Game Options
-  //#define MARLIN_BRICKOUT
-  //#define MARLIN_INVADERS
-  //#define MARLIN_SNAKE
+  #if ENABLED(SKRBoard)
+    #define MARLIN_BRICKOUT
+    #define MARLIN_INVADERS
+    #define MARLIN_SNAKE
+  #endif
   //#define GAMES_EASTER_EGG          // Add extra blank lines above the "Games" sub-menu
 
 #endif // HAS_GRAPHICAL_LCD
@@ -1572,18 +1594,18 @@
  *
  * Warning: Does not respect endstops!
  */
-//#define BABYSTEPPING
+#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
-  //#define INTEGRATED_BABYSTEPPING         // EXPERIMENTAL integration of babystepping into the Stepper ISR
+  #define INTEGRATED_BABYSTEPPING         // EXPERIMENTAL integration of babystepping into the Stepper ISR
   //#define BABYSTEP_WITHOUT_HOMING
-  //#define BABYSTEP_ALWAYS_AVAILABLE       // Allow babystepping at all times (not just during movement).
+  #define BABYSTEP_ALWAYS_AVAILABLE       // Allow babystepping at all times (not just during movement).
   //#define BABYSTEP_XY                     // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false           // Change if Z babysteps should go the other way
   //#define BABYSTEP_MILLIMETER_UNITS       // Specify BABYSTEP_MULTIPLICATOR_(XY|Z) in mm instead of micro-steps
-  #define BABYSTEP_MULTIPLICATOR_Z  1       // (steps or mm) Steps or millimeter distance for each Z babystep
+  #define BABYSTEP_MULTIPLICATOR_Z  (Z_STEPSMM / 40)       // (steps or mm) Steps or millimeter distance for each Z babystep
   #define BABYSTEP_MULTIPLICATOR_XY 1       // (steps or mm) Steps or millimeter distance for each XY babystep
 
-  //#define DOUBLECLICK_FOR_Z_BABYSTEPPING  // Double-click on the Status Screen for Z Babystepping.
+  #define DOUBLECLICK_FOR_Z_BABYSTEPPING  // Double-click on the Status Screen for Z Babystepping.
   #if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING)
     #define DOUBLECLICK_MAX_INTERVAL 1250   // Maximum interval between clicks, in milliseconds.
                                             // Note: Extra time may be added to mitigate controller latency.
@@ -1595,10 +1617,10 @@
 
   //#define BABYSTEP_DISPLAY_TOTAL          // Display total babysteps since last G28
 
-  //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
+  #define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets
-    //#define BABYSTEP_ZPROBE_GFX_OVERLAY   // Enable graphical overlay on Z-offset editor
+    #define BABYSTEP_ZPROBE_GFX_OVERLAY   // Enable graphical overlay on Z-offset editor
   #endif
 #endif
 
@@ -1619,12 +1641,14 @@
  *
  * See https://marlinfw.org/docs/features/lin_advance.html for full instructions.
  */
-//#define LIN_ADVANCE
+#if DISABLED(E_2208)
+  #define LIN_ADVANCE
+#endif
 #if ENABLED(LIN_ADVANCE)
   //#define EXTRA_LIN_ADVANCE_K // Enable for second linear advance constants
-  #define LIN_ADVANCE_K 0.22    // Unit: mm compression per 1mm/s extruder speed
+  #define LIN_ADVANCE_K 0.00    // Unit: mm compression per 1mm/s extruder speed
   //#define LA_DEBUG            // If enabled, this will generate debug information output over USB.
-  //#define EXPERIMENTAL_SCURVE // Enable this option to permit S-Curve Acceleration
+  #define EXPERIMENTAL_SCURVE // Enable this option to permit S-Curve Acceleration
 #endif
 
 // @section leveling
@@ -1772,7 +1796,7 @@
 #endif
 
 // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
-//#define BEZIER_CURVE_SUPPORT
+#define BEZIER_CURVE_SUPPORT
 
 /**
  * Direct Stepping
@@ -1813,8 +1837,8 @@
  *
  * Override the default value based on the driver type set in Configuration.h.
  */
-//#define MINIMUM_STEPPER_POST_DIR_DELAY 650
-//#define MINIMUM_STEPPER_PRE_DIR_DELAY 650
+#define MINIMUM_STEPPER_POST_DIR_DELAY 250
+#define MINIMUM_STEPPER_PRE_DIR_DELAY 250
 
 /**
  * Minimum stepper driver pulse width (in µs)
@@ -1858,8 +1882,8 @@
 // The value of BLOCK_BUFFER_SIZE must be a power of 2 (e.g. 8, 16, 32)
 #if BOTH(SDSUPPORT, DIRECT_STEPPING)
   #define BLOCK_BUFFER_SIZE  8
-#elif ENABLED(SDSUPPORT)
-  #define BLOCK_BUFFER_SIZE 16
+#elif ENABLED(SKRBoard)
+  #define BLOCK_BUFFER_SIZE 32
 #else
   #define BLOCK_BUFFER_SIZE 16
 #endif
@@ -1868,7 +1892,11 @@
 
 // The ASCII buffer for serial input
 #define MAX_CMD_SIZE 96
-#define BUFSIZE 4
+#if ENABLED(SKRBoard)
+  #define BUFSIZE 16
+#else
+  #define BUFSIZE 8
+#endif
 
 // Transmission to Host Buffer Size
 // To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0.
@@ -1877,8 +1905,11 @@
 // For debug-echo: 128 bytes for the optimal speed.
 // Other output doesn't need to be that speedy.
 // :[0, 2, 4, 8, 16, 32, 64, 128, 256]
-#define TX_BUFFER_SIZE 0
-
+#if ENABLED(SKRBoard)
+  #define TX_BUFFER_SIZE 32
+#else
+  #define TX_BUFFER_SIZE 0
+#endif
 // Host Receive Buffer Size
 // Without XON/XOFF flow control (see SERIAL_XON_XOFF below) 32 bytes should be enough.
 // To use flow control, set this buffer size to at least 1024 bytes.
@@ -1912,7 +1943,7 @@
  * Currently handles M108, M112, M410, M876
  * NOTE: Not yet implemented for all platforms.
  */
-//#define EMERGENCY_PARSER
+#define EMERGENCY_PARSER
 
 // Bad Serial-connections can miss a received command by sending an 'ok'
 // Therefore some clients abort after 30 seconds in a timeout.
@@ -1921,7 +1952,7 @@
 //#define NO_TIMEOUTS 1000 // Milliseconds
 
 // Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary.
-//#define ADVANCED_OK
+#define ADVANCED_OK
 
 // Printrun may have trouble receiving long strings all at once.
 // This option inserts short delays between lines of serial output.
@@ -1956,7 +1987,9 @@
  * Note that M207 / M208 / M209 settings are saved to EEPROM.
  *
  */
-//#define FWRETRACT
+#if DISABLED(UBL) || ENABLED(SKRBoard)
+  #define FWRETRACT
+#endif
 #if ENABLED(FWRETRACT)
   #define FWRETRACT_AUTORETRACT           // Override slicer retractions
   #if ENABLED(FWRETRACT_AUTORETRACT)
@@ -2056,7 +2089,7 @@
  * Requires NOZZLE_PARK_FEATURE.
  * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
  */
-//#define ADVANCED_PAUSE_FEATURE
+#define ADVANCED_PAUSE_FEATURE
 #if ENABLED(ADVANCED_PAUSE_FEATURE)
   #define PAUSE_PARK_RETRACT_FEEDRATE         60  // (mm/s) Initial retract feedrate.
   #define PAUSE_PARK_RETRACT_LENGTH            2  // (mm) Initial retract.
@@ -2072,7 +2105,7 @@
                                                   // 0 to disable start loading and skip to fast load only
   #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE   6  // (mm/s) Load filament feedrate. This can be pretty fast.
   #define FILAMENT_CHANGE_FAST_LOAD_ACCEL     25  // (mm/s^2) Lower acceleration may allow a faster feedrate.
-  #define FILAMENT_CHANGE_FAST_LOAD_LENGTH     0  // (mm) Load length of filament, from extruder gear to nozzle.
+  #define FILAMENT_CHANGE_FAST_LOAD_LENGTH     2  // (mm) Load length of filament, from extruder gear to nozzle.
                                                   //   For Bowden, the full length of the tube and nozzle.
                                                   //   For direct drive, the full length of the nozzle.
   //#define ADVANCED_PAUSE_CONTINUOUS_PURGE       // Purge continuously up to the purge length until interrupted.
@@ -2081,8 +2114,8 @@
                                                   //   Set to 0 for manual extrusion.
                                                   //   Filament can be extruded repeatedly from the Filament Change menu
                                                   //   until extrusion is consistent, and to purge old filament.
-  #define ADVANCED_PAUSE_RESUME_PRIME          0  // (mm) Extra distance to prime nozzle after returning from park.
-  //#define ADVANCED_PAUSE_FANS_PAUSE             // Turn off print-cooling fans while the machine is paused.
+  #define ADVANCED_PAUSE_RESUME_PRIME          2  // (mm) Extra distance to prime nozzle after returning from park.
+  #define ADVANCED_PAUSE_FANS_PAUSE             // Turn off print-cooling fans while the machine is paused.
 
                                                   // Filament Unload does a Retract, Delay, and Purge first:
   #define FILAMENT_UNLOAD_PURGE_RETRACT       13  // (mm) Unload initial retract length.
@@ -2091,14 +2124,14 @@
   #define FILAMENT_UNLOAD_PURGE_FEEDRATE      25  // (mm/s) feedrate to purge before unload
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT           45  // (seconds) Time limit before the nozzle is turned off for safety.
-  #define FILAMENT_CHANGE_ALERT_BEEPS         10  // Number of alert beeps to play when a response is needed.
+  #define FILAMENT_CHANGE_ALERT_BEEPS         2  // Number of alert beeps to play when a response is needed.
   #define PAUSE_PARK_NO_STEPPER_TIMEOUT           // Enable for XYZ steppers to stay powered on during filament change.
 
-  //#define PARK_HEAD_ON_PAUSE                    // Park the nozzle during pause and filament change.
-  //#define HOME_BEFORE_FILAMENT_CHANGE           // If needed, home before parking for filament change
+  #define PARK_HEAD_ON_PAUSE                    // Park the nozzle during pause and filament change.
+  #define HOME_BEFORE_FILAMENT_CHANGE           // Ensure homing has been completed prior to parking for filament change
 
-  //#define FILAMENT_LOAD_UNLOAD_GCODES           // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
-  //#define FILAMENT_UNLOAD_ALL_EXTRUDERS         // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
+  #define FILAMENT_LOAD_UNLOAD_GCODES           // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
+  #define FILAMENT_UNLOAD_ALL_EXTRUDERS         // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
 #endif
 
 // @section tmc
@@ -2394,15 +2427,35 @@
    * Set *_SERIAL_TX_PIN and *_SERIAL_RX_PIN to match for all drivers
    * on the same serial port, either here or in your board's pins file.
    */
-  #define  X_SLAVE_ADDRESS 0
-  #define  Y_SLAVE_ADDRESS 0
-  #define  Z_SLAVE_ADDRESS 0
+
+  #if ENABLED(SKRBoard)
+    #define  X_SLAVE_ADDRESS 0
+    #define  Y_SLAVE_ADDRESS 0
+    #define  Z_SLAVE_ADDRESS 0
+    #define E0_SLAVE_ADDRESS 0
+  #else
+    #define  X_SLAVE_ADDRESS 0
+    #define  Y_SLAVE_ADDRESS 2
+    #define  Z_SLAVE_ADDRESS 1
+    #define E0_SLAVE_ADDRESS 3
+    #define X_SERIAL_TX_PIN    58
+    #define X_SERIAL_RX_PIN    12
+
+    #define Y_SERIAL_TX_PIN    58
+    #define Y_SERIAL_RX_PIN    12
+
+    #define Z_SERIAL_TX_PIN    58
+    #define Z_SERIAL_RX_PIN    12
+
+    #define E0_SERIAL_TX_PIN   58
+    #define E0_SERIAL_RX_PIN   12
+  #endif
+
   #define X2_SLAVE_ADDRESS 0
   #define Y2_SLAVE_ADDRESS 0
   #define Z2_SLAVE_ADDRESS 0
   #define Z3_SLAVE_ADDRESS 0
   #define Z4_SLAVE_ADDRESS 0
-  #define E0_SLAVE_ADDRESS 0
   #define E1_SLAVE_ADDRESS 0
   #define E2_SLAVE_ADDRESS 0
   #define E3_SLAVE_ADDRESS 0
@@ -2426,7 +2479,7 @@
    */
   #define STEALTHCHOP_XY
   #define STEALTHCHOP_Z
-  #define STEALTHCHOP_E
+  //#define STEALTHCHOP_E
 
   /**
    * Optimize spreadCycle chopper parameters by using predefined parameter sets
@@ -2443,7 +2496,7 @@
    * Define you own with
    * { <off_time[1..15]>, <hysteresis_end[-3..12]>, hysteresis_start[1..8] }
    */
-  #define CHOPPER_TIMING CHOPPER_DEFAULT_12V
+  #define CHOPPER_TIMING CHOPPER_DEFAULT_24V
 
   /**
    * Monitor Trinamic drivers
@@ -2456,7 +2509,9 @@
    * M912 - Clear stepper driver overtemperature pre-warn condition flag.
    * M122 - Report driver parameters (Requires TMC_DEBUG)
    */
-  //#define MONITOR_DRIVER_STATUS
+  #if ENABLED(SKRBoard)
+    #define MONITOR_DRIVER_STATUS
+  #endif
 
   #if ENABLED(MONITOR_DRIVER_STATUS)
     #define CURRENT_STEP_DOWN     50  // [mA]
@@ -2471,12 +2526,12 @@
    * STEALTHCHOP_(XY|Z|E) must be enabled to use HYBRID_THRESHOLD.
    * M913 X/Y/Z/E to live tune the setting
    */
-  //#define HYBRID_THRESHOLD
+  #define HYBRID_THRESHOLD
 
-  #define X_HYBRID_THRESHOLD     100  // [mm/s]
-  #define X2_HYBRID_THRESHOLD    100
-  #define Y_HYBRID_THRESHOLD     100
-  #define Y2_HYBRID_THRESHOLD    100
+  #define X_HYBRID_THRESHOLD     70  // [mm/s]
+  #define X2_HYBRID_THRESHOLD    70
+  #define Y_HYBRID_THRESHOLD     50
+  #define Y2_HYBRID_THRESHOLD    50
   #define Z_HYBRID_THRESHOLD       3
   #define Z2_HYBRID_THRESHOLD      3
   #define Z3_HYBRID_THRESHOLD      3
@@ -2547,7 +2602,7 @@
    * Beta feature!
    * Create a 50/50 square wave step pulse optimal for stepper drivers.
    */
-  //#define SQUARE_WAVE_STEPPING
+  #define SQUARE_WAVE_STEPPING
 
   /**
    * Enable M122 debugging command for TMC stepper drivers.
@@ -2568,7 +2623,7 @@
    */
   #define TMC_ADV() {  }
 
-#endif // HAS_TRINAMIC_CONFIG
+#endif // HAS_TRINAMIC
 
 // @section L64XX
 
@@ -2864,13 +2919,18 @@
  * See https://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
  */
 //#define SPINDLE_FEATURE
-//#define LASER_FEATURE
+#if ENABLED(RAPTOR2) && DISABLED(SKRBoard)
+  #define LASER_FEATURE
+#endif
 #if EITHER(SPINDLE_FEATURE, LASER_FEATURE)
-  #define SPINDLE_LASER_ACTIVE_STATE    LOW    // Set to "HIGH" if the on/off function is active HIGH
-  #define SPINDLE_LASER_PWM             true   // Set to "true" if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      false  // Set to "true" if the speed/power goes up when you want it to go slower
+  //#define SHOW_CUTTER_ICON
+  #define SPINDLE_LASER_ACTIVE_STATE     HIGH  // Set to "true" if the on/off function is active HIGH
+  #define SPINDLE_LASER_PWM             false   // Set to "true" if your controller supports setting the speed/power
+  #define SPINDLE_LASER_PWM_INVERT      true   // Set to "true" if the speed/power goes up when you want it to go slower
 
-  #define SPINDLE_LASER_FREQUENCY       2500   // (Hz) Spindle/laser frequency (only on supported HALs: AVR and LPC)
+  #if ENABLED(SPINDLE_LASER_PWM)
+    //#define SPINDLE_LASER_FREQUENCY       2500   // (Hz) Spindle/laser frequency (only on supported HALs: AVR and LPC)
+  #endif
 
   /**
    * Speed / Power can be set ('M3 S') and displayed in terms of:
@@ -2895,8 +2955,8 @@
     #define SPINDLE_CHANGE_DIR_STOP            // Enable if the spindle should stop before changing spin direction
     #define SPINDLE_INVERT_DIR          false  // Set to "true" if the spin direction is reversed
 
-    #define SPINDLE_LASER_POWERUP_DELAY   5000 // (ms) Delay to allow the spindle/laser to come up to speed/power
-    #define SPINDLE_LASER_POWERDOWN_DELAY 5000 // (ms) Delay to allow the spindle to stop
+    #define SPINDLE_LASER_POWERUP_DELAY   1 // (ms) Delay to allow the spindle/laser to come up to speed/power
+    #define SPINDLE_LASER_POWERDOWN_DELAY 1 // (ms) Delay to allow the spindle to stop
 
     /**
      * M3/M4 Power Equation
@@ -2937,7 +2997,7 @@
        * - Ramps the power up every N steps to approximate the speed trapezoid.
        * - Due to the limited power resolution this is only approximate.
        */
-      #define LASER_POWER_INLINE_TRAPEZOID
+      //#define LASER_POWER_INLINE_TRAPEZOID
 
       /**
        * Continuously calculate the current power (nominal_power * current_rate / nominal_rate).
@@ -2996,6 +3056,7 @@
   #endif
 #endif
 
+
 /**
  * Coolant Control
  *
@@ -3193,27 +3254,40 @@
 /**
  * User-defined menu items that execute custom GCode
  */
-//#define CUSTOM_USER_MENUS
+
+#define CUSTOM_USER_MENUS
 #if ENABLED(CUSTOM_USER_MENUS)
-  //#define CUSTOM_USER_MENU_TITLE "Custom Commands"
-  #define USER_SCRIPT_DONE "M117 User Script Done"
+  //#define USER_SCRIPT_DONE "M117 User Script Done"
+  #define CUSTOM_USER_MENU_TITLE "Leveling Tools"
   #define USER_SCRIPT_AUDIBLE_FEEDBACK
-  //#define USER_SCRIPT_RETURN  // Return to status screen after a script
+  #define USER_SCRIPT_RETURN  // Return to status screen after a script
 
-  #define USER_DESC_1 "Home & UBL Info"
-  #define USER_GCODE_1 "G28\nG29 W"
+  #if ENABLED(DualZ)
+    #define DZ_Script "G34I8\n"
+  #else
+    #define DZ_Script
+  #endif
+  #define USER_DESC_1 "Setup"
+  #if ENABLED(UBL)
+    #define USER_GCODE_1 "M190S75\nG28\n" DZ_Script "G29P1\nG29P3\nM109S215\nG29S1\nG29S0\nG29F0.0\nG29A\nG28\nG1X150Y150F5000\nG1Z0\nM500\nM400\nM117 Set Z Offset"
+  #else
+    #define USER_GCODE_1 "M190S75\nG28\n" DZ_Script "G29\nM400\nM109S215\nG28\nM420S1\nG1X100Y100F5000\nG1Z0\nM500\nM117 Set Z Offset"
+  #endif
 
-  #define USER_DESC_2 "Preheat for " PREHEAT_1_LABEL
-  #define USER_GCODE_2 "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND)
+  #define USER_DESC_2 "PID Hotend"
+  #define USER_GCODE_2 "G28\nG1X200Y200Z5\nM106S128\nM303C8S215E0U\nM500\nM117 PID Tune Done"
 
-  #define USER_DESC_3 "Preheat for " PREHEAT_2_LABEL
-  #define USER_GCODE_3 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND)
+  #define USER_DESC_3 "PID Bed"
+  #define USER_GCODE_3 "M303C4S75E-1U\nM500\nM117 PID Tune Done"
 
-  #define USER_DESC_4 "Heat Bed/Home/Level"
-  #define USER_GCODE_4 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29"
+  #define USER_DESC_4 "Prep for Z Adjust"
+  #define USER_GCODE_4 "M190S75\nM104S215\nG28\nG29L1\nG1 X100Y100F5000\nG1Z0"
 
-  #define USER_DESC_5 "Home & Info"
-  #define USER_GCODE_5 "G28\nM503"
+  #define USER_DESC_5 "Store Settings"
+  #define USER_GCODE_5 "M500\nM117 Settings Stored"
+
+  #define USER_DESC_6 "Run Mesh Validation"
+  #define USER_GCODE_6 "G26"
 #endif
 
 /**
@@ -3230,10 +3304,10 @@
  * Host Prompt Support enables Marlin to use the host for user prompts so
  * filament runout and other processes can be managed from the host side.
  */
-//#define HOST_ACTION_COMMANDS
+#define HOST_ACTION_COMMANDS
 #if ENABLED(HOST_ACTION_COMMANDS)
-  //#define HOST_PROMPT_SUPPORT
-  //#define HOST_START_MENU_ITEM  // Add a menu item that tells the host to start
+  #define HOST_PROMPT_SUPPORT
+  #define HOST_START_MENU_ITEM  // Add a menu item that tells the host to start
 #endif
 
 /**
@@ -3241,7 +3315,7 @@
  *
  * Implement M486 to allow Marlin to skip objects
  */
-//#define CANCEL_OBJECTS
+#define CANCEL_OBJECTS
 
 /**
  * I2C position encoders for closed loop control.

Marlin/Version.h

@@ -1,6 +1,6 @@
 /**
  * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  *
  * Based on Sprinter and grbl.
  * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
@@ -28,25 +28,25 @@
 /**
  * Marlin release version identifier
  */
-//#define SHORT_BUILD_VERSION "bugfix-2.0.x"
+#define SHORT_BUILD_VERSION "2.0.6_R01"
 
 /**
  * Verbose version identifier which should contain a reference to the location
  * from where the binary was downloaded or the source code was compiled.
  */
-//#define DETAILED_BUILD_VERSION SHORT_BUILD_VERSION
+#define DETAILED_BUILD_VERSION SHORT_BUILD_VERSION " TM3D"
 
 /**
  * The STRING_DISTRIBUTION_DATE represents when the binary file was built,
  * here we define this default string as the date where the latest release
  * version was tagged.
  */
-//#define STRING_DISTRIBUTION_DATE "2019-07-10"
+#define STRING_DISTRIBUTION_DATE "2020-08-01"
 
 /**
  * Defines a generic printer name to be output to the LCD after booting Marlin.
  */
-//#define MACHINE_NAME "3D Printer"
+#define MACHINE_NAME "TM3D Raptor"
 
 /**
  * The SOURCE_CODE_URL is the location where users will find the Marlin Source
@@ -54,7 +54,7 @@
  * has a distinct Github fork— the Source Code URL should just be the main
  * Marlin repository.
  */
-//#define SOURCE_CODE_URL "https://github.com/MarlinFirmware/Marlin"
+#define SOURCE_CODE_URL "https://github.com/InsanityAutomation/Marlin/tree/Raptor_2.0.X"
 
 /**
  * Default generic printer UUID.
@@ -65,7 +65,7 @@
  * The WEBSITE_URL is the location where users can get more information such as
  * documentation about a specific Marlin release.
  */
-//#define WEBSITE_URL "https://marlinfw.org"
+#define WEBSITE_URL "tinymachines3d.com"
 
 /**
  * Set the vendor info the serial USB interface, if changable

Marlin/_Bootscreen.h

@@ -0,0 +1,105 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Custom Bitmap for splashscreen
+ *
+ * You may use one of the following tools to generate the C++ bitmap array from
+ * a black and white image:
+ *
+ *  - http://www.marlinfw.org/tools/u8glib/converter.html
+ *  - http://www.digole.com/tools/PicturetoC_Hex_converter.php
+ */
+
+#define CUSTOM_BOOTSCREEN_TIMEOUT   2500
+#define CUSTOM_BOOTSCREEN_BMPWIDTH  128
+#define CUSTOM_BOOTSCREEN_BMPHEIGHT 64
+
+const unsigned char custom_start_bmp[] PROGMEM = {
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFD, 0x55, 0x55, 0x55, 0x55, 0x55, 0x5F, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFE, 0x00, 0x00, 0x00, 0x00, 0x00, 0x3F, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFD, 0x00, 0x00, 0x07, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFE, 0x07, 0xC0, 0x05, 0x55, 0x55, 0x55, 0x55, 0x55, 0x5F, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFC, 0x0A, 0x20, 0x06, 0x00, 0x00, 0x00, 0x00, 0x00, 0x3F, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFE, 0x14, 0x10, 0x05, 0x00, 0x00, 0x07, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFC, 0x28, 0x08, 0x06, 0x07, 0xC0, 0x05, 0x55, 0x55, 0x55, 0x55, 0x55, 0x5F, 0xFF, 0xFF, 0xFF,
+0xFE, 0x54, 0x04, 0x04, 0x0A, 0x20, 0x06, 0x00, 0x00, 0x00, 0x00, 0x00, 0x3F, 0xFF, 0xFF, 0xFF,
+0xFC, 0x60, 0x04, 0x06, 0x14, 0x10, 0x05, 0x00, 0x00, 0x07, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFE, 0x50, 0x04, 0x04, 0x28, 0x08, 0x06, 0x07, 0xC0, 0x05, 0x55, 0x55, 0x55, 0x55, 0x55, 0x5F,
+0xFC, 0x60, 0x04, 0x06, 0x54, 0x04, 0x04, 0x0A, 0x20, 0x06, 0x00, 0x00, 0x00, 0x00, 0x00, 0x3F,
+0xFE, 0x54, 0x04, 0x1C, 0x60, 0x04, 0x06, 0x14, 0x10, 0x05, 0x00, 0x00, 0x00, 0x00, 0x00, 0x1F,
+0xFC, 0x28, 0x08, 0x2E, 0x50, 0x04, 0x04, 0x28, 0x08, 0x06, 0x07, 0xC0, 0x00, 0x01, 0xF0, 0x3F,
+0xFE, 0x14, 0x10, 0x54, 0x60, 0x04, 0x06, 0x54, 0x04, 0x04, 0x0A, 0x20, 0x00, 0x02, 0x08, 0x1F,
+0xFC, 0x0A, 0x20, 0x66, 0x54, 0x04, 0x1C, 0x60, 0x04, 0x06, 0x14, 0x10, 0x00, 0x05, 0x04, 0x3F,
+0xFE, 0x07, 0xC0, 0x54, 0x28, 0x08, 0x2E, 0x50, 0x04, 0x04, 0x28, 0x08, 0x00, 0x0A, 0x02, 0x1F,
+0xFC, 0x00, 0x00, 0x2E, 0x14, 0x10, 0x54, 0x60, 0x04, 0x06, 0x54, 0x04, 0x00, 0x15, 0x01, 0x3F,
+0xFE, 0x00, 0x00, 0x1C, 0x0A, 0x20, 0x66, 0x54, 0x04, 0x1C, 0x60, 0x04, 0x00, 0x18, 0x01, 0x1F,
+0xFC, 0x00, 0x00, 0x06, 0x07, 0xC0, 0x54, 0x28, 0x08, 0x2E, 0x50, 0x04, 0x00, 0x14, 0x01, 0x3F,
+0xFE, 0x00, 0x00, 0x04, 0x00, 0x00, 0x2E, 0x14, 0x10, 0x54, 0x60, 0x04, 0x00, 0x18, 0x01, 0x1F,
+0xFC, 0xFF, 0xFF, 0xFE, 0x00, 0x00, 0x1C, 0x0A, 0x20, 0x66, 0x54, 0x04, 0x1C, 0x15, 0x01, 0x3F,
+0xFE, 0xD5, 0x55, 0x54, 0x00, 0x00, 0x06, 0x07, 0xC0, 0x54, 0x28, 0x08, 0x2A, 0x0A, 0x02, 0x1F,
+0xFC, 0x84, 0x10, 0x46, 0x00, 0x00, 0x04, 0x00, 0x00, 0x2E, 0x14, 0x10, 0x51, 0x05, 0x04, 0x3F,
+0xFE, 0xC4, 0x10, 0x44, 0xFF, 0xFF, 0xFE, 0x00, 0x00, 0x1C, 0x0A, 0x20, 0x61, 0x02, 0x88, 0x1F,
+0xFC, 0x84, 0x10, 0x46, 0xD5, 0x55, 0x54, 0x00, 0x00, 0x06, 0x07, 0xC0, 0x51, 0x01, 0xF0, 0x3F,
+0xFE, 0x84, 0x10, 0x44, 0x84, 0x10, 0x46, 0x00, 0x00, 0x04, 0x00, 0x00, 0x2A, 0x00, 0x00, 0x1F,
+0xFC, 0xC4, 0x10, 0x46, 0xC4, 0x10, 0x44, 0xFF, 0xFF, 0xFE, 0x00, 0x00, 0x1C, 0x00, 0x00, 0x3F,
+0xFE, 0x84, 0x10, 0x44, 0x84, 0x10, 0x46, 0xD5, 0x55, 0x54, 0x00, 0x00, 0x00, 0x00, 0x00, 0x1F,
+0xFC, 0xD5, 0x55, 0x56, 0x84, 0x10, 0x44, 0x84, 0x10, 0x46, 0x00, 0x00, 0x00, 0x00, 0x00, 0x3F,
+0xFC, 0xFF, 0xFF, 0xFC, 0xC4, 0x10, 0x46, 0xC4, 0x10, 0x44, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0x9F,
+0xFE, 0x00, 0x00, 0x06, 0x84, 0x10, 0x44, 0x84, 0x10, 0x46, 0xD5, 0x55, 0x55, 0x55, 0x55, 0xBF,
+0xFD, 0x55, 0x55, 0x54, 0xD5, 0x55, 0x56, 0x84, 0x10, 0x44, 0x84, 0x10, 0x41, 0x04, 0x10, 0x9F,
+0xFF, 0xFF, 0xFF, 0xFC, 0xFF, 0xFF, 0xFC, 0xC4, 0x10, 0x46, 0xC4, 0x10, 0x41, 0x04, 0x11, 0xBF,
+0xFF, 0xFF, 0xFF, 0xFE, 0x00, 0x00, 0x06, 0x84, 0x10, 0x44, 0x84, 0x10, 0x41, 0x04, 0x10, 0x9F,
+0xFF, 0xFF, 0xFF, 0xFD, 0x55, 0x55, 0x54, 0xD5, 0x55, 0x56, 0x84, 0x10, 0x41, 0x04, 0x10, 0x9F,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFC, 0xFF, 0xFF, 0xFC, 0xC4, 0x10, 0x41, 0x04, 0x11, 0xBF,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFE, 0x00, 0x00, 0x06, 0x84, 0x10, 0x41, 0x04, 0x10, 0x9F,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFD, 0x55, 0x55, 0x54, 0xD5, 0x55, 0x55, 0x55, 0x55, 0xBF,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFC, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0x9F,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFE, 0x00, 0x00, 0x00, 0x00, 0x00, 0x3F,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFD, 0x55, 0x55, 0x55, 0x55, 0x55, 0x5F,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xE0, 0x2E, 0xFB, 0x7D, 0xFB, 0xFB, 0xCF, 0xC1, 0xDF, 0xBB, 0x3E, 0xC0, 0xE1, 0xFE, 0x3C, 0x1F,
+0xFD, 0xEE, 0x7B, 0x39, 0xF9, 0xF3, 0xCF, 0x9E, 0xDF, 0xBB, 0x3E, 0xDF, 0xDE, 0xFC, 0xDD, 0xE7,
+0xFD, 0xEE, 0x3B, 0xBB, 0xF9, 0xEB, 0xD7, 0xBF, 0x5F, 0xBB, 0x5E, 0xDF, 0xDE, 0xFD, 0xED, 0xF7,
+0xFD, 0xEE, 0xBB, 0xD3, 0xFA, 0xEB, 0xB7, 0x3F, 0xDF, 0xBB, 0x4E, 0xDF, 0xDF, 0xFF, 0xCD, 0xF3,
+0xFD, 0xEE, 0xDB, 0xC7, 0xFA, 0xEB, 0xBB, 0x7F, 0xC0, 0x3B, 0x6E, 0xC0, 0xE3, 0xFF, 0x1D, 0xF3,
+0xFD, 0xEE, 0xCB, 0xEF, 0xFA, 0xDB, 0xBB, 0x7F, 0xDF, 0xBB, 0x66, 0xDF, 0xF8, 0xFF, 0xCD, 0xF3,
+0xFD, 0xEE, 0xEB, 0xEF, 0xFB, 0x5B, 0x03, 0x3F, 0x5F, 0xBB, 0x76, 0xDF, 0xFE, 0x7F, 0xED, 0xF3,
+0xFD, 0xEE, 0xF3, 0xEF, 0xFB, 0x5B, 0x79, 0xBE, 0xDF, 0xBB, 0x7A, 0xDF, 0xDE, 0x7D, 0xED, 0xF7,
+0xFD, 0xEE, 0xF3, 0xEF, 0xFB, 0xBA, 0xFD, 0x9E, 0xDF, 0xBB, 0x7C, 0xDF, 0xDE, 0xFD, 0xCD, 0xE7,
+0xFD, 0xEE, 0xFB, 0xEF, 0xFB, 0xBA, 0xFD, 0xC1, 0xDF, 0xBB, 0x7E, 0xC0, 0xE0, 0xFE, 0x1C, 0x1F,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF
+};
+
+
+

Marlin/_Statusscreen.h

@@ -0,0 +1,74 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Custom Status Screen bitmap
+ *
+ * Place this file in the root with your configuration files
+ * and enable CUSTOM_STATUS_SCREEN_IMAGE in Configuration.h.
+ *
+ * Use the Marlin Bitmap Converter to make your own:
+ * http://marlinfw.org/tools/u8glib/converter.html
+ */
+
+//
+// Status Screen Logo bitmap
+//
+#define STATUS_LOGO_Y            3
+#define STATUS_LOGO_WIDTH       24
+
+const unsigned char status_logo_bmp[] PROGMEM = {
+  B11111111,B11111111,B11111111,
+  B10000000,B00000000,B00000001,
+  B10001110,B00000000,B11100001,
+  B10011111,B00000001,B11110001,
+  B10010011,B10000001,B00111001,
+  B10011111,B10000001,B11111001,
+  B10011111,B10000001,B11111001,
+  B10011111,B10111001,B11111001,
+  B10001111,B00101000,B11110001,
+  B10000000,B00111000,B00000001,
+  B10000000,B00000000,B00000001,
+  B10011111,B11111111,B11111001,
+  B10010001,B01110100,B10011001,
+  B10011011,B00000110,B10101001,
+  B10011011,B01010100,B10101001,
+  B10011011,B01010110,B10101001,
+  B10011011,B01010100,B10011001,
+  B10011111,B11111111,B11111001,
+  B11111111,B11111111,B11111111
+};
+
+//
+// Use default bitmaps
+//
+#define STATUS_HOTEND_ANIM
+#define STATUS_BED_ANIM
+#if HOTENDS < 2
+  #define STATUS_LOGO_X          8
+  #define STATUS_HEATERS_X      40
+  #define STATUS_BED_X          72
+#else
+  #define STATUS_LOGO_X          0
+  #define STATUS_HEATERS_X      32
+  #define STATUS_BED_X          80
+#endif