Initial Commit

Marlin/Configuration.h

@@ -69,7 +69,7 @@
 // @section info
 
 // Author info of this build printed to the host during boot and M115
-#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
+#define STRING_CONFIG_H_AUTHOR "Insanity Automation" // Who made the changes.
 //#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
 
 /**
@@ -139,7 +139,7 @@
 
 // Choose the name from boards.h that matches your setup
 #ifndef MOTHERBOARD
-  #define MOTHERBOARD BOARD_RAMPS_14_EFB
+  #define MOTHERBOARD BOARD_ORTUR_4
 #endif
 
 // Name displayed in the LCD "Ready" message and Info menu
@@ -429,7 +429,7 @@
 #define TEMP_SENSOR_5 0
 #define TEMP_SENSOR_6 0
 #define TEMP_SENSOR_7 0
-#define TEMP_SENSOR_BED 0
+#define TEMP_SENSOR_BED 1
 #define TEMP_SENSOR_PROBE 0
 #define TEMP_SENSOR_CHAMBER 0
 #define TEMP_SENSOR_COOLER 0
@@ -449,11 +449,11 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-#define TEMP_RESIDENCY_TIME         10  // (seconds) Time to wait for hotend to "settle" in M109
+#define TEMP_RESIDENCY_TIME         5  // (seconds) Time to wait for hotend to "settle" in M109
-#define TEMP_WINDOW                  1  // (°C) Temperature proximity for the "temperature reached" timer
+#define TEMP_WINDOW                  2  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_HYSTERESIS              3  // (°C) Temperature proximity considered "close enough" to the target
 
-#define TEMP_BED_RESIDENCY_TIME     10  // (seconds) Time to wait for bed to "settle" in M190
+#define TEMP_BED_RESIDENCY_TIME     5  // (seconds) Time to wait for bed to "settle" in M190
 #define TEMP_BED_WINDOW              1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS          3  // (°C) Temperature proximity considered "close enough" to the target
 
@@ -485,7 +485,7 @@
 #define HEATER_5_MAXTEMP 275
 #define HEATER_6_MAXTEMP 275
 #define HEATER_7_MAXTEMP 275
-#define BED_MAXTEMP      150
+#define BED_MAXTEMP      120
 #define CHAMBER_MAXTEMP  60
 
 /**
@@ -510,8 +510,8 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  #define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
+  #define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -545,7 +545,7 @@
  * heater. If your configuration is significantly different than this and you don't understand
  * the issues involved, don't use bed PID until someone else verifies that your hardware works.
  */
-//#define PIDTEMPBED
+#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
@@ -563,9 +563,9 @@
 
   // 120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
   // from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define DEFAULT_bedKp 10.00
+  #define DEFAULT_bedKp 87.23
-  #define DEFAULT_bedKi .023
+  #define DEFAULT_bedKi 13.31
-  #define DEFAULT_bedKd 305.4
+  #define DEFAULT_bedKd 381.14
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED
@@ -722,13 +722,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
 #define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
 #define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
 #define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -811,14 +811,14 @@
  * Override with M92
  *                                      X, Y, Z, E0 [, E1[, E2...]]
  */
-#define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 80, 400, 500 }
+#define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 80, 400, 95 }
 
 /**
  * Default Max Feed Rate (mm/s)
  * Override with M203
  *                                      X, Y, Z, E0 [, E1[, E2...]]
  */
-#define DEFAULT_MAX_FEEDRATE          { 300, 300, 5, 25 }
+#define DEFAULT_MAX_FEEDRATE          { 500, 500, 10, 65 }
 
 //#define LIMITED_MAX_FR_EDITING        // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
 #if ENABLED(LIMITED_MAX_FR_EDITING)
@@ -831,7 +831,7 @@
  * Override with M201
  *                                      X, Y, Z, E0 [, E1[, E2...]]
  */
-#define DEFAULT_MAX_ACCELERATION      { 3000, 3000, 100, 10000 }
+#define DEFAULT_MAX_ACCELERATION      { 2500, 2500, 18000, 8000 }
 
 //#define LIMITED_MAX_ACCEL_EDITING     // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
 #if ENABLED(LIMITED_MAX_ACCEL_EDITING)
@@ -846,8 +846,8 @@
  *   M204 R    Retract Acceleration
  *   M204 T    Travel Acceleration
  */
-#define DEFAULT_ACCELERATION          3000    // X, Y, Z and E acceleration for printing moves
+#define DEFAULT_ACCELERATION          2000    // X, Y, Z and E acceleration for printing moves
-#define DEFAULT_RETRACT_ACCELERATION  3000    // E acceleration for retracts
+#define DEFAULT_RETRACT_ACCELERATION  2000    // E acceleration for retracts
 #define DEFAULT_TRAVEL_ACCELERATION   3000    // X, Y, Z acceleration for travel (non printing) moves
 
 /**
@@ -858,10 +858,10 @@
  * When changing speed and direction, if the difference is less than the
  * value set here, it may happen instantaneously.
  */
-//#define CLASSIC_JERK
+#define CLASSIC_JERK
 #if ENABLED(CLASSIC_JERK)
-  #define DEFAULT_XJERK 10.0
+  #define DEFAULT_XJERK 15.0
-  #define DEFAULT_YJERK 10.0
+  #define DEFAULT_YJERK 15.0
   #define DEFAULT_ZJERK  0.3
 
   //#define TRAVEL_EXTRA_XYJERK 0.0     // Additional jerk allowance for all travel moves
@@ -895,7 +895,7 @@
  *
  * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained
  */
-//#define S_CURVE_ACCELERATION
+#define S_CURVE_ACCELERATION
 
 //===========================================================================
 //============================= Z Probe Options =============================
@@ -911,7 +911,7 @@
  * The probe replaces the Z-MIN endstop and is used for Z homing.
  * (Automatically enables USE_PROBE_FOR_Z_HOMING.)
  */
-#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
+//#define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN
 
 // Force the use of the probe for Z-axis homing
 //#define USE_PROBE_FOR_Z_HOMING
@@ -951,7 +951,7 @@
  * A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
  *   (e.g., an inductive probe or a nozzle-based probe-switch.)
  */
-//#define FIX_MOUNTED_PROBE
+#define FIX_MOUNTED_PROBE
 
 /**
  * Use the nozzle as the probe, as with a conductive
@@ -1060,17 +1060,17 @@
  *     |    [-]    |
  *     O-- FRONT --+
  */
-#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
+#define NOZZLE_TO_PROBE_OFFSET { -25, 0, 0 }
 
 // Most probes should stay away from the edges of the bed, but
 // with NOZZLE_AS_PROBE this can be negative for a wider probing area.
-#define PROBING_MARGIN 10
+#define PROBING_MARGIN 8
 
 // X and Y axis travel speed (mm/min) between probes
 #define XY_PROBE_FEEDRATE (133*60)
 
 // Feedrate (mm/min) for the first approach when double-probing (MULTIPLE_PROBING == 2)
-#define Z_PROBE_FEEDRATE_FAST (4*60)
+#define Z_PROBE_FEEDRATE_FAST (10*60)
 
 // Feedrate (mm/min) for the "accurate" probe of each point
 #define Z_PROBE_FEEDRATE_SLOW (Z_PROBE_FEEDRATE_FAST / 2)
@@ -1111,7 +1111,7 @@
  * A total of 2 does fast/slow probes with a weighted average.
  * A total of 3 or more adds more slow probes, taking the average.
  */
-//#define MULTIPLE_PROBING 2
+#define MULTIPLE_PROBING 2
 //#define EXTRA_PROBING    1
 
 /**
@@ -1128,16 +1128,16 @@
  * Example: `M851 Z-5` with a CLEARANCE of 4  =>  9mm from bed to nozzle.
  *     But: `M851 Z+1` with a CLEARANCE of 2  =>  2mm from bed to nozzle.
  */
-#define Z_CLEARANCE_DEPLOY_PROBE   10 // Z Clearance for Deploy/Stow
+#define Z_CLEARANCE_DEPLOY_PROBE   5 // Z Clearance for Deploy/Stow
 #define Z_CLEARANCE_BETWEEN_PROBES  5 // Z Clearance between probe points
 #define Z_CLEARANCE_MULTI_PROBE     5 // Z Clearance between multiple probes
 //#define Z_AFTER_PROBING           5 // Z position after probing is done
 
-#define Z_PROBE_LOW_POINT          -2 // Farthest distance below the trigger-point to go before stopping
+#define Z_PROBE_LOW_POINT          -4 // Farthest distance below the trigger-point to go before stopping
 
 // For M851 give a range for adjusting the Z probe offset
-#define Z_PROBE_OFFSET_RANGE_MIN -20
+#define Z_PROBE_OFFSET_RANGE_MIN -9
-#define Z_PROBE_OFFSET_RANGE_MAX 20
+#define Z_PROBE_OFFSET_RANGE_MAX 9
 
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
@@ -1197,12 +1197,12 @@
 // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
 #define INVERT_X_DIR false
 #define INVERT_Y_DIR true
-#define INVERT_Z_DIR false
+#define INVERT_Z_DIR true
 
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.
-#define INVERT_E0_DIR false
+#define INVERT_E0_DIR true
 #define INVERT_E1_DIR false
 #define INVERT_E2_DIR false
 #define INVERT_E3_DIR false
@@ -1237,16 +1237,16 @@
 // @section machine
 
 // The size of the printable area
-#define X_BED_SIZE 200
+#define X_BED_SIZE 255
-#define Y_BED_SIZE 200
+#define Y_BED_SIZE 300
 
 // Travel limits (mm) after homing, corresponding to endstop positions.
-#define X_MIN_POS 0
+#define X_MIN_POS -10.5
-#define Y_MIN_POS 0
+#define Y_MIN_POS -9
 #define Z_MIN_POS 0
-#define X_MAX_POS X_BED_SIZE
+#define X_MAX_POS 260
-#define Y_MAX_POS Y_BED_SIZE
+#define Y_MAX_POS 310
-#define Z_MAX_POS 200
+#define Z_MAX_POS 295
 
 /**
  * Software Endstops
@@ -1274,7 +1274,7 @@
 #endif
 
 #if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS)
-  //#define SOFT_ENDSTOPS_MENU_ITEM  // Enable/Disable software endstops from the LCD
+  #define SOFT_ENDSTOPS_MENU_ITEM  // Enable/Disable software endstops from the LCD
 #endif
 
 /**
@@ -1290,7 +1290,7 @@
  * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
  * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
  */
-//#define FILAMENT_RUNOUT_SENSOR
+#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define FIL_RUNOUT_ENABLED_DEFAULT true // Enable the sensor on startup. Override with M412 followed by M500.
   #define NUM_RUNOUT_SENSORS   1          // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
@@ -1342,7 +1342,7 @@
   // After a runout is detected, continue printing this length of filament
   // before executing the runout script. Useful for a sensor at the end of
   // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead.
-  //#define FILAMENT_RUNOUT_DISTANCE_MM 25
+  #define FILAMENT_RUNOUT_DISTANCE_MM 5
 
   #ifdef FILAMENT_RUNOUT_DISTANCE_MM
     // Enable this option to use an encoder disc that toggles the runout pin
@@ -1392,7 +1392,7 @@
  */
 //#define AUTO_BED_LEVELING_3POINT
 //#define AUTO_BED_LEVELING_LINEAR
-//#define AUTO_BED_LEVELING_BILINEAR
+#define AUTO_BED_LEVELING_BILINEAR
 //#define AUTO_BED_LEVELING_UBL
 //#define MESH_BED_LEVELING
 
@@ -1401,13 +1401,13 @@
  * these options to restore the prior leveling state or to always enable
  * leveling immediately after G28.
  */
-//#define RESTORE_LEVELING_AFTER_G28
+#define RESTORE_LEVELING_AFTER_G28
 //#define ENABLE_LEVELING_AFTER_G28
 
 /**
  * Auto-leveling needs preheating
  */
-//#define PREHEAT_BEFORE_LEVELING
+#define PREHEAT_BEFORE_LEVELING
 #if ENABLED(PREHEAT_BEFORE_LEVELING)
   #define LEVELING_NOZZLE_TEMP 120   // (°C) Only applies to E0 at this time
   #define LEVELING_BED_TEMP     50
@@ -1431,7 +1431,7 @@
   // The height can be set with M420 Z<height>
   #define ENABLE_LEVELING_FADE_HEIGHT
   #if ENABLED(ENABLE_LEVELING_FADE_HEIGHT)
-    #define DEFAULT_LEVELING_FADE_HEIGHT 10.0 // (mm) Default fade height.
+    #define DEFAULT_LEVELING_FADE_HEIGHT 0.0 // (mm) Default fade height.
   #endif
 
   // For Cartesian machines, instead of dividing moves on mesh boundaries,
@@ -1459,7 +1459,7 @@
 #if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR)
 
   // Set the number of grid points per dimension.
-  #define GRID_MAX_POINTS_X 3
+  #define GRID_MAX_POINTS_X 5
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
 
   // Probe along the Y axis, advancing X after each column
@@ -1523,27 +1523,27 @@
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */
-//#define LCD_BED_LEVELING
+#define LCD_BED_LEVELING
 
 #if ENABLED(LCD_BED_LEVELING)
   #define MESH_EDIT_Z_STEP  0.025 // (mm) Step size while manually probing Z axis.
   #define LCD_PROBE_Z_RANGE 4     // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment
-  //#define MESH_EDIT_MENU        // Add a menu to edit mesh points
+  #define MESH_EDIT_MENU        // Add a menu to edit mesh points
 #endif
 
 // Add a menu item to move between bed corners for manual bed adjustment
-//#define LEVEL_BED_CORNERS
+#define LEVEL_BED_CORNERS
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets
   #define LEVEL_CORNERS_HEIGHT      0.0   // (mm) Z height of nozzle at leveling points
   #define LEVEL_CORNERS_Z_HOP       4.0   // (mm) Z height of nozzle between leveling points
   //#define LEVEL_CENTER_TOO              // Move to the center after the last corner
-  //#define LEVEL_CORNERS_USE_PROBE
+  #define LEVEL_CORNERS_USE_PROBE
   #if ENABLED(LEVEL_CORNERS_USE_PROBE)
     #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1
     #define LEVEL_CORNERS_VERIFY_RAISED   // After adjustment triggers the probe, re-probe to verify
-    //#define LEVEL_CORNERS_AUDIO_FEEDBACK
+    #define LEVEL_CORNERS_AUDIO_FEEDBACK
   #endif
 
   /**
@@ -1677,12 +1677,12 @@
  *   M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
  *   M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
  */
-//#define EEPROM_SETTINGS     // Persistent storage with M500 and M501
+#define EEPROM_SETTINGS     // Persistent storage with M500 and M501
 //#define DISABLE_M503        // Saves ~2700 bytes of PROGMEM. Disable for release!
 #define EEPROM_CHITCHAT       // Give feedback on EEPROM commands. Disable to save PROGMEM.
 #define EEPROM_BOOT_SILENT    // Keep M503 quiet and only give errors during first load
 #if ENABLED(EEPROM_SETTINGS)
-  //#define EEPROM_AUTO_INIT  // Init EEPROM automatically on any errors.
+  #define EEPROM_AUTO_INIT  // Init EEPROM automatically on any errors.
 #endif
 
 //
@@ -1733,11 +1733,11 @@
  *    P1  Raise the nozzle always to Z-park height.
  *    P2  Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
  */
-//#define NOZZLE_PARK_FEATURE
+#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
   // Specify a park position as { X, Y, Z_raise }
-  #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
+  #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MIN_POS + 10), 5 }
   //#define NOZZLE_PARK_X_ONLY          // X move only is required to park
   //#define NOZZLE_PARK_Y_ONLY          // Y move only is required to park
   #define NOZZLE_PARK_Z_RAISE_MIN   2   // (mm) Always raise Z by at least this distance
@@ -1941,7 +1941,7 @@
  * SD Card support is disabled by default. If your controller has an SD slot,
  * you must uncomment the following option or it won't work.
  */
-//#define SDSUPPORT
+#define SDSUPPORT
 
 /**
  * SD CARD: ENABLE CRC
@@ -1988,7 +1988,7 @@
 //
 //  Set this option if CLOCKWISE causes values to DECREASE
 //
-//#define REVERSE_ENCODER_DIRECTION
+#define REVERSE_ENCODER_DIRECTION
 
 //
 // This option reverses the encoder direction for navigating LCD menus.
@@ -2011,7 +2011,7 @@
 //
 // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
 //
-//#define INDIVIDUAL_AXIS_HOMING_MENU
+#define INDIVIDUAL_AXIS_HOMING_MENU
 
 //
 // SPEAKER/BUZZER
@@ -2019,7 +2019,7 @@
 // If you have a speaker that can produce tones, enable it here.
 // By default Marlin assumes you have a buzzer with a fixed frequency.
 //
-//#define SPEAKER
+#define SPEAKER
 
 //
 // The duration and frequency for the UI feedback sound.
@@ -2200,7 +2200,7 @@
 // RepRapDiscount FULL GRAPHIC Smart Controller
 // https://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
 //
-//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
+#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
 
 //
 // K.3D Full Graphic Smart Controller

Marlin/Configuration_adv.h

@@ -239,11 +239,11 @@
  */
 #if ENABLED(THERMAL_PROTECTION_HOTENDS)
   #define THERMAL_PROTECTION_PERIOD 40        // Seconds
-  #define THERMAL_PROTECTION_HYSTERESIS 4     // Degrees Celsius
+  #define THERMAL_PROTECTION_HYSTERESIS 15     // Degrees Celsius
 
-  //#define ADAPTIVE_FAN_SLOWING              // Slow part cooling fan if temperature drops
+  #define ADAPTIVE_FAN_SLOWING              // Slow part cooling fan if temperature drops
   #if BOTH(ADAPTIVE_FAN_SLOWING, PIDTEMP)
-    //#define NO_FAN_SLOWING_IN_PID_TUNING    // Don't slow fan speed during M303
+    #define NO_FAN_SLOWING_IN_PID_TUNING    // Don't slow fan speed during M303
   #endif
 
   /**
@@ -437,9 +437,9 @@
  * Hotend Idle Timeout
  * Prevent filament in the nozzle from charring and causing a critical jam.
  */
-//#define HOTEND_IDLE_TIMEOUT
+#define HOTEND_IDLE_TIMEOUT
 #if ENABLED(HOTEND_IDLE_TIMEOUT)
-  #define HOTEND_IDLE_TIMEOUT_SEC (5*60)    // (seconds) Time without extruder movement to trigger protection
+  #define HOTEND_IDLE_TIMEOUT_SEC (15*60)    // (seconds) Time without extruder movement to trigger protection
   #define HOTEND_IDLE_MIN_TRIGGER   180     // (°C) Minimum temperature to enable hotend protection
   #define HOTEND_IDLE_NOZZLE_TARGET   0     // (°C) Safe temperature for the nozzle after timeout
   #define HOTEND_IDLE_BED_TARGET      0     // (°C) Safe temperature for the bed after timeout
@@ -648,7 +648,7 @@
 //
 // For Z set the number of stepper drivers
 //
-#define NUM_Z_STEPPER_DRIVERS 1   // (1-4) Z options change based on how many
+#define NUM_Z_STEPPER_DRIVERS 2   // (1-4) Z options change based on how many
 
 #if NUM_Z_STEPPER_DRIVERS > 1
   // Enable if Z motor direction signals are the opposite of Z1
@@ -741,7 +741,7 @@
 
 //#define HOMING_BACKOFF_POST_MM { 2, 2, 2 }  // (mm) Backoff from endstops after homing
 
-//#define QUICK_HOME                          // If G28 contains XY do a diagonal move first
+#define QUICK_HOME                          // If G28 contains XY do a diagonal move first
 //#define HOME_Y_BEFORE_X                     // If G28 contains XY home Y before X
 //#define HOME_Z_FIRST                        // Home Z first. Requires a Z-MIN endstop (not a probe).
 //#define CODEPENDENT_XY_HOMING               // If X/Y can't home without homing Y/X first
@@ -821,7 +821,7 @@
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.
  */
-//#define Z_STEPPER_AUTO_ALIGN
+#define Z_STEPPER_AUTO_ALIGN
 #if ENABLED(Z_STEPPER_AUTO_ALIGN)
   // Define probe X and Y positions for Z1, Z2 [, Z3 [, Z4]]
   // If not defined, probe limits will be used.
@@ -965,12 +965,12 @@
 // Backlash Compensation
 // Adds extra movement to axes on direction-changes to account for backlash.
 //
-//#define BACKLASH_COMPENSATION
+#define BACKLASH_COMPENSATION
 #if ENABLED(BACKLASH_COMPENSATION)
   // Define values for backlash distance and correction.
   // If BACKLASH_GCODE is enabled these values are the defaults.
   #define BACKLASH_DISTANCE_MM { 0, 0, 0 } // (mm)
-  #define BACKLASH_CORRECTION    0.0       // 0.0 = no correction; 1.0 = full correction
+  #define BACKLASH_CORRECTION    0.1       // 0.0 = no correction; 1.0 = full correction
 
   // Add steps for motor direction changes on CORE kinematics
   //#define CORE_BACKLASH
@@ -980,7 +980,7 @@
   //#define BACKLASH_SMOOTHING_MM 3 // (mm)
 
   // Add runtime configuration and tuning of backlash values (M425)
-  //#define BACKLASH_GCODE
+  #define BACKLASH_GCODE
 
   #if ENABLED(BACKLASH_GCODE)
     // Measure the Z backlash when probing (G29) and set with "M425 Z"
@@ -1175,7 +1175,7 @@
   #endif
 
   // Include a page of printer information in the LCD Main Menu
-  //#define LCD_INFO_MENU
+  #define LCD_INFO_MENU
   #if ENABLED(LCD_INFO_MENU)
     //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages
   #endif
@@ -1229,13 +1229,13 @@
   #endif
 
   // Scroll a longer status message into view
-  //#define STATUS_MESSAGE_SCROLLING
+  #define STATUS_MESSAGE_SCROLLING
 
   // On the Info Screen, display XY with one decimal place when possible
   //#define LCD_DECIMAL_SMALL_XY
 
   // Add an 'M73' G-code to set the current percentage
-  //#define LCD_SET_PROGRESS_MANUALLY
+  #define LCD_SET_PROGRESS_MANUALLY
 
   // Show the E position (filament used) during printing
   //#define LCD_SHOW_E_TOTAL
@@ -1317,7 +1317,7 @@
    * an option on the LCD screen to continue the print from the last-known
    * point in the file.
    */
-  //#define POWER_LOSS_RECOVERY
+  #define POWER_LOSS_RECOVERY
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT   false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
     //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
@@ -1383,10 +1383,10 @@
   //#define UTF_FILENAME_SUPPORT
 
   // This allows hosts to request long names for files and folders with M33
-  //#define LONG_FILENAME_HOST_SUPPORT
+  #define LONG_FILENAME_HOST_SUPPORT
 
   // Enable this option to scroll long filenames in the SD card menu
-  //#define SCROLL_LONG_FILENAMES
+  #define SCROLL_LONG_FILENAMES
 
   // Leave the heaters on after Stop Print (not recommended!)
   //#define SD_ABORT_NO_COOLDOWN
@@ -1408,7 +1408,7 @@
   /**
    * Auto-report SdCard status with M27 S<seconds>
    */
-  //#define AUTO_REPORT_SD_STATUS
+  #define AUTO_REPORT_SD_STATUS
 
   /**
    * Support for USB thumb drives using an Arduino USB Host Shield or
@@ -1792,18 +1792,18 @@
  *
  * Warning: Does not respect endstops!
  */
-//#define BABYSTEPPING
+#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
-  //#define INTEGRATED_BABYSTEPPING         // EXPERIMENTAL integration of babystepping into the Stepper ISR
+  #define INTEGRATED_BABYSTEPPING         // EXPERIMENTAL integration of babystepping into the Stepper ISR
   //#define BABYSTEP_WITHOUT_HOMING
-  //#define BABYSTEP_ALWAYS_AVAILABLE       // Allow babystepping at all times (not just during movement).
+  #define BABYSTEP_ALWAYS_AVAILABLE       // Allow babystepping at all times (not just during movement).
   //#define BABYSTEP_XY                     // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false           // Change if Z babysteps should go the other way
   //#define BABYSTEP_MILLIMETER_UNITS       // Specify BABYSTEP_MULTIPLICATOR_(XY|Z) in mm instead of micro-steps
   #define BABYSTEP_MULTIPLICATOR_Z  1       // (steps or mm) Steps or millimeter distance for each Z babystep
   #define BABYSTEP_MULTIPLICATOR_XY 1       // (steps or mm) Steps or millimeter distance for each XY babystep
 
-  //#define DOUBLECLICK_FOR_Z_BABYSTEPPING  // Double-click on the Status Screen for Z Babystepping.
+  #define DOUBLECLICK_FOR_Z_BABYSTEPPING  // Double-click on the Status Screen for Z Babystepping.
   #if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING)
     #define DOUBLECLICK_MAX_INTERVAL 1250   // Maximum interval between clicks, in milliseconds.
                                             // Note: Extra time may be added to mitigate controller latency.
@@ -1815,10 +1815,10 @@
 
   //#define BABYSTEP_DISPLAY_TOTAL          // Display total babysteps since last G28
 
-  //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
+  #define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets
-    //#define BABYSTEP_ZPROBE_GFX_OVERLAY   // Enable graphical overlay on Z-offset editor
+    #define BABYSTEP_ZPROBE_GFX_OVERLAY   // Enable graphical overlay on Z-offset editor
   #endif
 #endif
 
@@ -2140,7 +2140,7 @@
  * Currently handles M108, M112, M410, M876
  * NOTE: Not yet implemented for all platforms.
  */
-//#define EMERGENCY_PARSER
+#define EMERGENCY_PARSER
 
 /**
  * Realtime Reporting (requires EMERGENCY_PARSER)
@@ -2169,7 +2169,7 @@
 //#define NO_TIMEOUTS 1000 // Milliseconds
 
 // Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary.
-//#define ADVANCED_OK
+#define ADVANCED_OK
 
 // Printrun may have trouble receiving long strings all at once.
 // This option inserts short delays between lines of serial output.
@@ -2310,7 +2310,7 @@
  *
  * Enable PARK_HEAD_ON_PAUSE to add the G-code M125 Pause and Park.
  */
-//#define ADVANCED_PAUSE_FEATURE
+#define ADVANCED_PAUSE_FEATURE
 #if ENABLED(ADVANCED_PAUSE_FEATURE)
   #define PAUSE_PARK_RETRACT_FEEDRATE         60  // (mm/s) Initial retract feedrate.
   #define PAUSE_PARK_RETRACT_LENGTH            2  // (mm) Initial retract.
@@ -2345,14 +2345,14 @@
   #define FILAMENT_UNLOAD_PURGE_FEEDRATE      25  // (mm/s) feedrate to purge before unload
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT           45  // (seconds) Time limit before the nozzle is turned off for safety.
-  #define FILAMENT_CHANGE_ALERT_BEEPS         10  // Number of alert beeps to play when a response is needed.
+  #define FILAMENT_CHANGE_ALERT_BEEPS         2  // Number of alert beeps to play when a response is needed.
   #define PAUSE_PARK_NO_STEPPER_TIMEOUT           // Enable for XYZ steppers to stay powered on during filament change.
 
-  //#define PARK_HEAD_ON_PAUSE                    // Park the nozzle during pause and filament change.
+  #define PARK_HEAD_ON_PAUSE                    // Park the nozzle during pause and filament change.
-  //#define HOME_BEFORE_FILAMENT_CHANGE           // If needed, home before parking for filament change
+  #define HOME_BEFORE_FILAMENT_CHANGE           // If needed, home before parking for filament change
 
-  //#define FILAMENT_LOAD_UNLOAD_GCODES           // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
+  #define FILAMENT_LOAD_UNLOAD_GCODES           // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
-  //#define FILAMENT_UNLOAD_ALL_EXTRUDERS         // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
+  #define FILAMENT_UNLOAD_ALL_EXTRUDERS         // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
 #endif
 
 // @section tmc
@@ -3649,10 +3649,10 @@
  * Host Prompt Support enables Marlin to use the host for user prompts so
  * filament runout and other processes can be managed from the host side.
  */
-//#define HOST_ACTION_COMMANDS
+#define HOST_ACTION_COMMANDS
 #if ENABLED(HOST_ACTION_COMMANDS)
-  //#define HOST_PROMPT_SUPPORT
+  #define HOST_PROMPT_SUPPORT
-  //#define HOST_START_MENU_ITEM  // Add a menu item that tells the host to start
+  #define HOST_START_MENU_ITEM  // Add a menu item that tells the host to start
 #endif
 
 /**
@@ -4001,7 +4001,7 @@
 //
 // M43 - display pin status, toggle pins, watch pins, watch endstops & toggle LED, test servo probe
 //
-//#define PINS_DEBUGGING
+#define PINS_DEBUGGING
 
 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE