Update Configuration_adv.h
Co-Authored-By: Chris Pepper <24342+p3p@users.noreply.github.com>
This commit is contained in:
InsanityAutomation
+49
-49
@@ -307,11 +307,11 @@
|
||||
#define THERMAL_PROTECTION_PERIOD 40 // (seconds)
|
||||
#define THERMAL_PROTECTION_HYSTERESIS 4 // (°C)
|
||||
|
||||
//#define ADAPTIVE_FAN_SLOWING // Slow down the part-cooling fan if the temperature drops
|
||||
#define ADAPTIVE_FAN_SLOWING // Slow down the part-cooling fan if the temperature drops
|
||||
#if ENABLED(ADAPTIVE_FAN_SLOWING)
|
||||
//#define REPORT_ADAPTIVE_FAN_SLOWING // Report fan slowing activity to the console
|
||||
#if ANY(MPCTEMP, PIDTEMP)
|
||||
//#define TEMP_TUNING_MAINTAIN_FAN // Don't slow down the fan speed during M303 or M306 T
|
||||
#define TEMP_TUNING_MAINTAIN_FAN // Don't slow down the fan speed during M303 or M306 T
|
||||
#endif
|
||||
#endif
|
||||
|
||||
@@ -335,7 +335,7 @@
|
||||
* Thermal Protection parameters for the bed are just as above for hotends.
|
||||
*/
|
||||
#if ENABLED(THERMAL_PROTECTION_BED)
|
||||
#define THERMAL_PROTECTION_BED_PERIOD 20 // (seconds)
|
||||
#define THERMAL_PROTECTION_BED_PERIOD 90 // (seconds)
|
||||
#define THERMAL_PROTECTION_BED_HYSTERESIS 2 // (°C)
|
||||
|
||||
/**
|
||||
@@ -547,10 +547,10 @@
|
||||
* Hotend Idle Timeout
|
||||
* Prevent filament in the nozzle from charring and causing a critical jam.
|
||||
*/
|
||||
//#define HOTEND_IDLE_TIMEOUT
|
||||
#define HOTEND_IDLE_TIMEOUT
|
||||
#if ENABLED(HOTEND_IDLE_TIMEOUT)
|
||||
#define HOTEND_IDLE_TIMEOUT_SEC (5*60) // (seconds) Time without extruder movement to trigger protection
|
||||
#define HOTEND_IDLE_MIN_TRIGGER 180 // (°C) Minimum temperature to enable hotend protection
|
||||
#define HOTEND_IDLE_TIMEOUT_SEC (30*60) // (seconds) Time without extruder movement to trigger protection
|
||||
#define HOTEND_IDLE_MIN_TRIGGER 170 // (°C) Minimum temperature to enable hotend protection
|
||||
#define HOTEND_IDLE_NOZZLE_TARGET 0 // (°C) Safe temperature for the nozzle after timeout
|
||||
#define HOTEND_IDLE_BED_TARGET 0 // (°C) Safe temperature for the bed after timeout
|
||||
#endif
|
||||
@@ -602,8 +602,8 @@
|
||||
* gets it spinning reliably for a short time before setting the requested speed.
|
||||
* (Does not work on Sanguinololu with FAN_SOFT_PWM.)
|
||||
*/
|
||||
//#define FAN_KICKSTART_TIME 100 // (ms)
|
||||
//#define FAN_KICKSTART_POWER 180 // 64-255
|
||||
#define FAN_KICKSTART_TIME 100 // (ms)
|
||||
#define FAN_KICKSTART_POWER 180 // 64-255
|
||||
|
||||
// Some coolers may require a non-zero "off" state.
|
||||
//#define FAN_OFF_PWM 1
|
||||
@@ -931,7 +931,7 @@
|
||||
//#define HOMING_BACKOFF_POST_MM { 2, 2, 2 } // (linear=mm, rotational=°) Backoff from endstops after homing
|
||||
//#define XY_COUNTERPART_BACKOFF_MM 0 // (mm) Backoff X after homing Y, and vice-versa
|
||||
|
||||
//#define QUICK_HOME // If G28 contains XY do a diagonal move first
|
||||
#define QUICK_HOME // If G28 contains XY do a diagonal move first
|
||||
//#define HOME_Y_BEFORE_X // If G28 contains XY home Y before X
|
||||
//#define HOME_Z_FIRST // Home Z first. Requires a real endstop (not a probe).
|
||||
//#define CODEPENDENT_XY_HOMING // If X/Y can't home without homing Y/X first
|
||||
@@ -1020,7 +1020,7 @@
|
||||
* Z Steppers Auto-Alignment
|
||||
* Add the G34 command to align multiple Z steppers using a bed probe.
|
||||
*/
|
||||
//#define Z_STEPPER_AUTO_ALIGN
|
||||
#define Z_STEPPER_AUTO_ALIGN
|
||||
#if ENABLED(Z_STEPPER_AUTO_ALIGN)
|
||||
/**
|
||||
* Define probe X and Y positions for Z1, Z2 [, Z3 [, Z4]]
|
||||
@@ -1281,7 +1281,7 @@
|
||||
// Backlash Compensation
|
||||
// Adds extra movement to axes on direction-changes to account for backlash.
|
||||
//
|
||||
//#define BACKLASH_COMPENSATION
|
||||
#define BACKLASH_COMPENSATION
|
||||
#if ENABLED(BACKLASH_COMPENSATION)
|
||||
// Define values for backlash distance and correction.
|
||||
// If BACKLASH_GCODE is enabled these values are the defaults.
|
||||
@@ -1296,7 +1296,7 @@
|
||||
//#define BACKLASH_SMOOTHING_MM 3 // (mm)
|
||||
|
||||
// Add runtime configuration and tuning of backlash values (M425)
|
||||
//#define BACKLASH_GCODE
|
||||
#define BACKLASH_GCODE
|
||||
|
||||
#if ENABLED(BACKLASH_GCODE)
|
||||
// Measure the Z backlash when probing (G29) and set with "M425 Z"
|
||||
@@ -1342,7 +1342,7 @@
|
||||
#define CALIBRATION_NOZZLE_TIP_HEIGHT 1.0 // mm
|
||||
#define CALIBRATION_NOZZLE_OUTER_DIAMETER 2.0 // mm
|
||||
|
||||
// Uncomment to enable reporting (required for "G425 V", but consumes flash).
|
||||
// Uncomment to enable reporting (required for "G425 V", but consumes PROGMEM).
|
||||
//#define CALIBRATION_REPORTING
|
||||
|
||||
// The true location and dimension the cube/bolt/washer on the bed.
|
||||
@@ -1528,7 +1528,7 @@
|
||||
#endif
|
||||
|
||||
// Include a page of printer information in the LCD Main Menu
|
||||
//#define LCD_INFO_MENU
|
||||
#define LCD_INFO_MENU
|
||||
#if ENABLED(LCD_INFO_MENU)
|
||||
//#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages
|
||||
#endif
|
||||
@@ -1580,7 +1580,7 @@
|
||||
#define BOOT_MARLIN_LOGO_SMALL // Show a smaller Marlin logo on the Boot Screen (saving lots of flash)
|
||||
#endif
|
||||
#if HAS_MARLINUI_U8GLIB
|
||||
//#define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~3260 (or ~940) bytes of flash.
|
||||
#define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~3260 (or ~940) bytes of flash.
|
||||
#endif
|
||||
#if ANY(HAS_MARLINUI_U8GLIB, TOUCH_UI_FTDI_EVE)
|
||||
//#define SHOW_CUSTOM_BOOTSCREEN // Show the bitmap in Marlin/_Bootscreen.h on startup.
|
||||
@@ -1599,10 +1599,10 @@
|
||||
#endif
|
||||
|
||||
// The timeout to return to the status screen from sub-menus
|
||||
//#define LCD_TIMEOUT_TO_STATUS 15000 // (ms)
|
||||
#define LCD_TIMEOUT_TO_STATUS 15000 // (ms)
|
||||
|
||||
// Scroll a longer status message into view
|
||||
//#define STATUS_MESSAGE_SCROLLING
|
||||
#define STATUS_MESSAGE_SCROLLING
|
||||
|
||||
// Apply a timeout to low-priority status messages
|
||||
//#define STATUS_MESSAGE_TIMEOUT_SEC 30 // (seconds)
|
||||
@@ -1654,7 +1654,7 @@
|
||||
#endif
|
||||
|
||||
// Add 'M73' to set print job progress, overrides Marlin's built-in estimate
|
||||
//#define SET_PROGRESS_MANUALLY
|
||||
#define SET_PROGRESS_MANUALLY
|
||||
#if ENABLED(SET_PROGRESS_MANUALLY)
|
||||
#define SET_PROGRESS_PERCENT // Add 'P' parameter to set percentage done
|
||||
#define SET_REMAINING_TIME // Add 'R' parameter to set remaining time
|
||||
@@ -1806,13 +1806,13 @@
|
||||
|
||||
// Allow international symbols in long filenames. To display correctly, the
|
||||
// LCD's font must contain the characters. Check your selected LCD language.
|
||||
//#define UTF_FILENAME_SUPPORT
|
||||
#define UTF_FILENAME_SUPPORT
|
||||
|
||||
//#define LONG_FILENAME_HOST_SUPPORT // Get the long filename of a file/folder with 'M33 <dosname>' and list long filenames with 'M20 L'
|
||||
#define LONG_FILENAME_HOST_SUPPORT // Get the long filename of a file/folder with 'M33 <dosname>' and list long filenames with 'M20 L'
|
||||
//#define LONG_FILENAME_WRITE_SUPPORT // Create / delete files with long filenames via M28, M30, and Binary Transfer Protocol
|
||||
//#define M20_TIMESTAMP_SUPPORT // Include timestamps by adding the 'T' flag to M20 commands
|
||||
|
||||
//#define SCROLL_LONG_FILENAMES // Scroll long filenames in the SD card menu
|
||||
#define SCROLL_LONG_FILENAMES // Scroll long filenames in the SD card menu
|
||||
|
||||
//#define SD_ABORT_NO_COOLDOWN // Leave the heaters on after Stop Print (not recommended!)
|
||||
|
||||
@@ -2263,18 +2263,18 @@
|
||||
*
|
||||
* Warning: Does not respect endstops!
|
||||
*/
|
||||
//#define BABYSTEPPING
|
||||
#define BABYSTEPPING
|
||||
#if ENABLED(BABYSTEPPING)
|
||||
//#define EP_BABYSTEPPING // M293/M294 babystepping with EMERGENCY_PARSER support
|
||||
//#define BABYSTEP_WITHOUT_HOMING
|
||||
//#define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement)
|
||||
#define BABYSTEP_ALWAYS_AVAILABLE // Allow babystepping at all times (not just during movement)
|
||||
//#define BABYSTEP_XY // Also enable X/Y Babystepping. Not supported on DELTA!
|
||||
//#define BABYSTEP_INVERT_Z // Enable if Z babysteps should go the other way
|
||||
//#define BABYSTEP_MILLIMETER_UNITS // Specify BABYSTEP_MULTIPLICATOR_(XY|Z) in mm instead of micro-steps
|
||||
#define BABYSTEP_MULTIPLICATOR_Z 1 // (steps or mm) Steps or millimeter distance for each Z babystep
|
||||
#define BABYSTEP_MULTIPLICATOR_Z 25 // (steps or mm) Steps or millimeter distance for each Z babystep
|
||||
#define BABYSTEP_MULTIPLICATOR_XY 1 // (steps or mm) Steps or millimeter distance for each XY babystep
|
||||
|
||||
//#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
|
||||
#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
|
||||
#if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING)
|
||||
#define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
|
||||
// Note: Extra time may be added to mitigate controller latency.
|
||||
@@ -2286,10 +2286,10 @@
|
||||
|
||||
//#define BABYSTEP_DISPLAY_TOTAL // Display total babysteps since last G28
|
||||
|
||||
//#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping
|
||||
#define BABYSTEP_ZPROBE_OFFSET // Combine M851 Z and Babystepping
|
||||
#if ENABLED(BABYSTEP_ZPROBE_OFFSET)
|
||||
//#define BABYSTEP_HOTEND_Z_OFFSET // For multiple hotends, babystep relative Z offsets
|
||||
//#define BABYSTEP_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
|
||||
#define BABYSTEP_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
|
||||
#endif
|
||||
#endif
|
||||
|
||||
@@ -2310,7 +2310,7 @@
|
||||
*
|
||||
* See https://marlinfw.org/docs/features/lin_advance.html for full instructions.
|
||||
*/
|
||||
//#define LIN_ADVANCE
|
||||
#define LIN_ADVANCE
|
||||
#if ENABLED(LIN_ADVANCE)
|
||||
#if ENABLED(DISTINCT_E_FACTORS)
|
||||
#define ADVANCE_K { 0.22 } // (mm) Compression length per 1mm/s extruder speed, per extruder
|
||||
@@ -2319,7 +2319,7 @@
|
||||
#endif
|
||||
//#define ADVANCE_K_EXTRA // Add a second linear advance constant, configurable with M900 L.
|
||||
//#define LA_DEBUG // Print debug information to serial during operation. Disable for production use.
|
||||
//#define ALLOW_LOW_EJERK // Allow a DEFAULT_EJERK value of <10. Recommended for direct drive hotends.
|
||||
#define ALLOW_LOW_EJERK // Allow a DEFAULT_EJERK value of <10. Recommended for direct drive hotends.
|
||||
//#define EXPERIMENTAL_I2S_LA // Allow I2S_STEPPER_STREAM to be used with LA. Performance degrades as the LA step rate reaches ~20kHz.
|
||||
#endif
|
||||
|
||||
@@ -2504,7 +2504,7 @@
|
||||
#endif
|
||||
|
||||
// G5 Bézier Curve Support with XYZE destination and IJPQ offsets
|
||||
//#define BEZIER_CURVE_SUPPORT // Requires ~2666 bytes
|
||||
#define BEZIER_CURVE_SUPPORT // Requires ~2666 bytes
|
||||
|
||||
#if ANY(ARC_SUPPORT, BEZIER_CURVE_SUPPORT)
|
||||
//#define CNC_WORKSPACE_PLANES // Allow G2/G3/G5 to operate in XY, ZX, or YZ planes
|
||||
@@ -2596,16 +2596,16 @@
|
||||
#if ALL(HAS_MEDIA, DIRECT_STEPPING)
|
||||
#define BLOCK_BUFFER_SIZE 8
|
||||
#elif HAS_MEDIA
|
||||
#define BLOCK_BUFFER_SIZE 16
|
||||
#define BLOCK_BUFFER_SIZE 32
|
||||
#else
|
||||
#define BLOCK_BUFFER_SIZE 16
|
||||
#define BLOCK_BUFFER_SIZE 32
|
||||
#endif
|
||||
|
||||
// @section serial
|
||||
|
||||
// The ASCII buffer for serial input
|
||||
#define MAX_CMD_SIZE 96
|
||||
#define BUFSIZE 4
|
||||
#define BUFSIZE 16
|
||||
|
||||
// Transmission to Host Buffer Size
|
||||
// To save 386 bytes of flash (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0.
|
||||
@@ -2652,7 +2652,7 @@
|
||||
* Currently handles M108, M112, M410, M876
|
||||
* NOTE: Not yet implemented for all platforms.
|
||||
*/
|
||||
//#define EMERGENCY_PARSER
|
||||
#define EMERGENCY_PARSER
|
||||
|
||||
/**
|
||||
* Realtime Reporting (requires EMERGENCY_PARSER)
|
||||
@@ -2683,7 +2683,7 @@
|
||||
//#define NO_TIMEOUTS 1000 // (ms)
|
||||
|
||||
// Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary.
|
||||
//#define ADVANCED_OK
|
||||
#define ADVANCED_OK
|
||||
|
||||
// Printrun may have trouble receiving long strings all at once.
|
||||
// This option inserts short delays between lines of serial output.
|
||||
@@ -2885,7 +2885,7 @@
|
||||
*
|
||||
* Enable PARK_HEAD_ON_PAUSE to add the G-code M125 Pause and Park.
|
||||
*/
|
||||
//#define ADVANCED_PAUSE_FEATURE
|
||||
#define ADVANCED_PAUSE_FEATURE
|
||||
#if ENABLED(ADVANCED_PAUSE_FEATURE)
|
||||
#define PAUSE_PARK_RETRACT_FEEDRATE 60 // (mm/s) Initial retract feedrate.
|
||||
#define PAUSE_PARK_RETRACT_LENGTH 2 // (mm) Initial retract.
|
||||
@@ -2925,11 +2925,11 @@
|
||||
//#define FILAMENT_CHANGE_RESUME_ON_INSERT // Automatically continue / load filament when runout sensor is triggered again.
|
||||
//#define PAUSE_REHEAT_FAST_RESUME // Reduce number of waits by not prompting again post-timeout before continuing.
|
||||
|
||||
//#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
#define PARK_HEAD_ON_PAUSE // Park the nozzle during pause and filament change.
|
||||
//#define HOME_BEFORE_FILAMENT_CHANGE // If needed, home before parking for filament change
|
||||
|
||||
//#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
//#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#define FILAMENT_LOAD_UNLOAD_GCODES // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
|
||||
#define FILAMENT_UNLOAD_ALL_EXTRUDERS // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
|
||||
#define CONFIGURE_FILAMENT_CHANGE // Add M603 G-code and menu items. Requires ~1.3K bytes of flash.
|
||||
#endif
|
||||
|
||||
@@ -3110,7 +3110,7 @@
|
||||
#endif
|
||||
|
||||
#if AXIS_IS_TMC_CONFIG(E0)
|
||||
#define E0_CURRENT 800
|
||||
#define E0_CURRENT 900
|
||||
#define E0_MICROSTEPS 16
|
||||
#define E0_RSENSE 0.11
|
||||
#define E0_CHAIN_POS -1
|
||||
@@ -3283,7 +3283,7 @@
|
||||
#define STEALTHCHOP_U
|
||||
#define STEALTHCHOP_V
|
||||
#define STEALTHCHOP_W
|
||||
#define STEALTHCHOP_E
|
||||
//#define STEALTHCHOP_E
|
||||
#endif
|
||||
|
||||
/**
|
||||
@@ -3301,7 +3301,7 @@
|
||||
* Define your own with:
|
||||
* { <off_time[1..15]>, <hysteresis_end[-3..12]>, hysteresis_start[1..8] }
|
||||
*/
|
||||
#define CHOPPER_TIMING CHOPPER_DEFAULT_12V // All axes (override below)
|
||||
#define CHOPPER_TIMING CHOPPER_DEFAULT_24V // All axes (override below)
|
||||
//#define CHOPPER_TIMING_X CHOPPER_TIMING // For X Axes (override below)
|
||||
//#define CHOPPER_TIMING_X2 CHOPPER_TIMING_X
|
||||
//#define CHOPPER_TIMING_Y CHOPPER_TIMING // For Y Axes (override below)
|
||||
@@ -3445,7 +3445,7 @@
|
||||
/**
|
||||
* Step on both rising and falling edge signals (as with a square wave).
|
||||
*/
|
||||
//#define EDGE_STEPPING
|
||||
#define EDGE_STEPPING
|
||||
|
||||
/**
|
||||
* Enable M122 debugging command for TMC stepper drivers.
|
||||
@@ -4114,14 +4114,14 @@
|
||||
* Host Prompt Support enables Marlin to use the host for user prompts so
|
||||
* filament runout and other processes can be managed from the host side.
|
||||
*/
|
||||
//#define HOST_ACTION_COMMANDS
|
||||
#define HOST_ACTION_COMMANDS
|
||||
#if ENABLED(HOST_ACTION_COMMANDS)
|
||||
//#define HOST_PAUSE_M76 // Tell the host to pause in response to M76
|
||||
//#define HOST_PROMPT_SUPPORT // Initiate host prompts to get user feedback
|
||||
#define HOST_PROMPT_SUPPORT // Initiate host prompts to get user feedback
|
||||
#if ENABLED(HOST_PROMPT_SUPPORT)
|
||||
//#define HOST_STATUS_NOTIFICATIONS // Send some status messages to the host as notifications
|
||||
#define HOST_STATUS_NOTIFICATIONS // Send some status messages to the host as notifications
|
||||
#endif
|
||||
//#define HOST_START_MENU_ITEM // Add a menu item that tells the host to start
|
||||
#define HOST_START_MENU_ITEM // Add a menu item that tells the host to start
|
||||
//#define HOST_SHUTDOWN_MENU_ITEM // Add a menu item that tells the host to shut down
|
||||
#endif
|
||||
|
||||
@@ -4489,12 +4489,12 @@
|
||||
//
|
||||
// M42 - Set pin states
|
||||
//
|
||||
//#define DIRECT_PIN_CONTROL
|
||||
#define DIRECT_PIN_CONTROL
|
||||
|
||||
//
|
||||
// M43 - display pin status, toggle pins, watch pins, watch endstops & toggle LED, test servo probe
|
||||
//
|
||||
//#define PINS_DEBUGGING
|
||||
#define PINS_DEBUGGING
|
||||
|
||||
// Enable Tests that will run at startup and produce a report
|
||||
//#define MARLIN_TEST_BUILD
|
||||
|
||||
Reference in New Issue
Block a user