Update Configuration.h

Marlin/Configuration.h

@@ -1,3 +1,12 @@
+//#define TronxyXY2A
+#define TronxyXY2
+//#define TronxyX5SPro
+//#define TronxyX3
+//#define TronxyX3A
+
+//#define TMC2208Drv
+//#define TitanExtruder
+
 /**
  * Marlin 3D Printer Firmware
  * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
@@ -69,7 +78,7 @@
 // @section info
 
 // Author info of this build printed to the host during boot and M115
-#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
+#define STRING_CONFIG_H_AUTHOR "InsanityAutomation" // Who made the changes.
 //#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
 
 /**
@@ -102,7 +111,7 @@
  *
  * :[-1, 0, 1, 2, 3, 4, 5, 6, 7]
  */
-#define SERIAL_PORT 0
+#define SERIAL_PORT 1
 
 /**
  * Serial Port Baud Rate
@@ -123,7 +132,7 @@
  * Currently Ethernet (-2) is only supported on Teensy 4.1 boards.
  * :[-2, -1, 0, 1, 2, 3, 4, 5, 6, 7]
  */
-//#define SERIAL_PORT_2 -1
+#define SERIAL_PORT_2 3
 //#define BAUDRATE_2 250000   // Enable to override BAUDRATE
 
 /**
@@ -139,11 +148,27 @@
 
 // Choose the name from boards.h that matches your setup
 #ifndef MOTHERBOARD
-  #define MOTHERBOARD BOARD_RAMPS_14_EFB
+  #if ANY(TronxyXY2, TronxyXY2A)
+    #define MOTHERBOARD BOARD_CHITU3D_V9
+  #elif ANY(TronxyX3A, TronxyX3)
+    #define MOTHERBOARD BOARD_CHITU3D_V9
+  #else
+    #define MOTHERBOARD BOARD_CHITU3D_V6
+  #endif
 #endif
 
 // Name displayed in the LCD "Ready" message and Info menu
-//#define CUSTOM_MACHINE_NAME "3D Printer"
+#if ENABLED(TronxyX5SPro)
+  #define CUSTOM_MACHINE_NAME "Tronxy X5SA"
+#elif ENABLED(TronxyXY2)
+  #define CUSTOM_MACHINE_NAME "Tronxy XY2"
+#elif ENABLED(TronxyXY2A)
+  #define CUSTOM_MACHINE_NAME "Tronxy XY2A"
+#elif ENABLED(TronxyX3)
+  #define CUSTOM_MACHINE_NAME "Tronxy X3"
+#elif ENABLED(TronxyX3A)
+  #define CUSTOM_MACHINE_NAME "Tronxy X3A"
+#endif
 
 // Printer's unique ID, used by some programs to differentiate between machines.
 // Choose your own or use a service like https://www.uuidgenerator.net/version4
@@ -493,7 +518,7 @@
 #define TEMP_SENSOR_5 0
 #define TEMP_SENSOR_6 0
 #define TEMP_SENSOR_7 0
-#define TEMP_SENSOR_BED 0
+#define TEMP_SENSOR_BED 1
 #define TEMP_SENSOR_PROBE 0
 #define TEMP_SENSOR_CHAMBER 0
 #define TEMP_SENSOR_COOLER 0
@@ -510,11 +535,11 @@
 //#define MAX31865_SENSOR_OHMS_1      100
 //#define MAX31865_CALIBRATION_OHMS_1 430
 
-#define TEMP_RESIDENCY_TIME         10  // (seconds) Time to wait for hotend to "settle" in M109
+#define TEMP_RESIDENCY_TIME          5  // (seconds) Time to wait for hotend to "settle" in M109
 #define TEMP_WINDOW                  1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_HYSTERESIS              3  // (°C) Temperature proximity considered "close enough" to the target
 
-#define TEMP_BED_RESIDENCY_TIME     10  // (seconds) Time to wait for bed to "settle" in M190
+#define TEMP_BED_RESIDENCY_TIME      3  // (seconds) Time to wait for bed to "settle" in M190
 #define TEMP_BED_WINDOW              1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS          3  // (°C) Temperature proximity considered "close enough" to the target
 
@@ -587,8 +612,8 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
+  #define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  #define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -624,7 +649,7 @@
  */
 //#define PIDTEMPBED
 
-//#define BED_LIMIT_SWITCHING
+#define BED_LIMIT_SWITCHING
 
 /**
  * Max Bed Power
@@ -748,7 +773,9 @@
 
 // Enable one of the options below for CoreXY, CoreXZ, or CoreYZ kinematics,
 // either in the usual order or reversed
-//#define COREXY
+#if ENABLED(TronxyX5SPro)
+  #define COREXY
+#endif
 //#define COREXZ
 //#define COREYZ
 //#define COREYX
@@ -779,7 +806,7 @@
 //#define USE_KMAX_PLUG
 
 // Enable pullup for all endstops to prevent a floating state
-#define ENDSTOPPULLUPS
+//#define ENDSTOPPULLUPS
 #if DISABLED(ENDSTOPPULLUPS)
   // Disable ENDSTOPPULLUPS to set pullups individually
   //#define ENDSTOPPULLUP_XMAX
@@ -817,9 +844,9 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
+#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
 #define I_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
 #define J_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
 #define K_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
@@ -829,7 +856,7 @@
 #define I_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
 #define J_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
 #define K_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -849,9 +876,9 @@
  *          TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE
  * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'L6474', 'POWERSTEP01', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
  */
-#define X_DRIVER_TYPE  A4988
-#define Y_DRIVER_TYPE  A4988
-#define Z_DRIVER_TYPE  A4988
+#define X_DRIVER_TYPE  TMC2208_STANDALONE
+#define Y_DRIVER_TYPE  TMC2208_STANDALONE
+#define Z_DRIVER_TYPE  TMC2208_STANDALONE
 //#define X2_DRIVER_TYPE A4988
 //#define Y2_DRIVER_TYPE A4988
 //#define Z2_DRIVER_TYPE A4988
@@ -860,7 +887,7 @@
 //#define I_DRIVER_TYPE  A4988
 //#define J_DRIVER_TYPE  A4988
 //#define K_DRIVER_TYPE  A4988
-#define E0_DRIVER_TYPE A4988
+#define E0_DRIVER_TYPE TMC2208_STANDALONE
 //#define E1_DRIVER_TYPE A4988
 //#define E2_DRIVER_TYPE A4988
 //#define E3_DRIVER_TYPE A4988
@@ -915,8 +942,19 @@
  * Override with M92
  *                                      X, Y, Z [, I [, J [, K]]], E0 [, E1[, E2...]]
  */
-#define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 80, 400, 500 }
-
+#if ENABLED(TMC2208Drv)
+  #if ENABLED(TitanExtruder)
+    #define DEFAULT_AXIS_STEPS_PER_UNIT   { 160, 160, 800, 764 }
+  #else
+    #define DEFAULT_AXIS_STEPS_PER_UNIT   { 160, 160, 800, 382 }
+  #endif
+#else
+  #if ENABLED(TitanExtruder)
+    #define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 80, 400, 185.2 }
+  #else
+    #define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 80, 400, 92.6 }
+  #endif
+#endif
 /**
  * Default Max Feed Rate (mm/s)
  * Override with M203
@@ -935,7 +973,7 @@
  * Override with M201
  *                                      X, Y, Z [, I [, J [, K]]], E0 [, E1[, E2...]]
  */
-#define DEFAULT_MAX_ACCELERATION      { 3000, 3000, 100, 10000 }
+#define DEFAULT_MAX_ACCELERATION      { 1500, 1500, 100, 5000 }
 
 //#define LIMITED_MAX_ACCEL_EDITING     // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
 #if ENABLED(LIMITED_MAX_ACCEL_EDITING)
@@ -950,9 +988,9 @@
  *   M204 R    Retract Acceleration
  *   M204 T    Travel Acceleration
  */
-#define DEFAULT_ACCELERATION          3000    // X, Y, Z and E acceleration for printing moves
-#define DEFAULT_RETRACT_ACCELERATION  3000    // E acceleration for retracts
-#define DEFAULT_TRAVEL_ACCELERATION   3000    // X, Y, Z acceleration for travel (non printing) moves
+#define DEFAULT_ACCELERATION          1500    // X, Y, Z and E acceleration for printing moves
+#define DEFAULT_RETRACT_ACCELERATION  1500    // E acceleration for retracts
+#define DEFAULT_TRAVEL_ACCELERATION   1500    // X, Y, Z acceleration for travel (non printing) moves
 
 /**
  * Default Jerk limits (mm/s)
@@ -962,7 +1000,7 @@
  * When changing speed and direction, if the difference is less than the
  * value set here, it may happen instantaneously.
  */
-//#define CLASSIC_JERK
+#define CLASSIC_JERK
 #if ENABLED(CLASSIC_JERK)
   #define DEFAULT_XJERK 10.0
   #define DEFAULT_YJERK 10.0
@@ -1002,7 +1040,7 @@
  *
  * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained
  */
-//#define S_CURVE_ACCELERATION
+#define S_CURVE_ACCELERATION
 
 //===========================================================================
 //============================= Z Probe Options =============================
@@ -1052,13 +1090,22 @@
  * Use G29 repeatedly, adjusting the Z height at each point with movement commands
  * or (with LCD_BED_LEVELING) the LCD controller.
  */
-//#define PROBE_MANUALLY
-
+#if ANY(TronxyX3, TronxyXY2)
+  #define PROBE_MANUALLY
+  #define MANUAL_PROBE_START_Z 0.2
+#endif
 /**
  * A Fix-Mounted Probe either doesn't deploy or needs manual deployment.
  *   (e.g., an inductive probe or a nozzle-based probe-switch.)
  */
-//#define FIX_MOUNTED_PROBE
+#if NONE(TronxyX3, TronxyXY2)
+  #define FIX_MOUNTED_PROBE
+#endif
+/**
+ * Use the nozzle as the probe, with the hotend
+ * assembly attached to a sensitive strain gauge.
+ */
+//#define STRAIN_GAUGE_PROBE
 
 /**
  * Use the nozzle as the probe, as with a conductive
@@ -1167,11 +1214,11 @@
  *     |    [-]    |
  *     O-- FRONT --+
  */
-#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
+#define NOZZLE_TO_PROBE_OFFSET { -40, 0, 0 }
 
 // Most probes should stay away from the edges of the bed, but
 // with NOZZLE_AS_PROBE this can be negative for a wider probing area.
-#define PROBING_MARGIN 10
+#define PROBING_MARGIN 50
 
 // X and Y axis travel speed (mm/min) between probes
 #define XY_PROBE_FEEDRATE (133*60)
@@ -1218,7 +1265,7 @@
  * A total of 2 does fast/slow probes with a weighted average.
  * A total of 3 or more adds more slow probes, taking the average.
  */
-//#define MULTIPLE_PROBING 2
+#define MULTIPLE_PROBING 2
 //#define EXTRA_PROBING    1
 
 /**
@@ -1240,15 +1287,16 @@
 #define Z_CLEARANCE_MULTI_PROBE     5 // Z Clearance between multiple probes
 //#define Z_AFTER_PROBING           5 // Z position after probing is done
 
-#define Z_PROBE_LOW_POINT          -2 // Farthest distance below the trigger-point to go before stopping
+#define Z_PROBE_LOW_POINT          -4 // Farthest distance below the trigger-point to go before stopping
 
 // For M851 give a range for adjusting the Z probe offset
-#define Z_PROBE_OFFSET_RANGE_MIN -20
-#define Z_PROBE_OFFSET_RANGE_MAX 20
+#define Z_PROBE_OFFSET_RANGE_MIN -9
+#define Z_PROBE_OFFSET_RANGE_MAX 9
 
 // Enable the M48 repeatability test to test probe accuracy
-//#define Z_MIN_PROBE_REPEATABILITY_TEST
-
+#if NONE(TronxyX3, TronxyXY2)
+  #define Z_MIN_PROBE_REPEATABILITY_TEST
+#endif
 // Before deploy/stow pause for user confirmation
 //#define PAUSE_BEFORE_DEPLOY_STOW
 #if ENABLED(PAUSE_BEFORE_DEPLOY_STOW)
@@ -1309,17 +1357,24 @@
 // @section machine
 
 // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
-#define INVERT_X_DIR false
-#define INVERT_Y_DIR true
-#define INVERT_Z_DIR false
+#if BOTH(TronxyX5SPro, TMC2208Drv) || ANY(TronxyXY2A, TronxyXY2, TronxyX3, TronxyX3A)
+  #define INVERT_X_DIR false
+  #define INVERT_Y_DIR true
+  #define INVERT_Z_DIR true
+  #define INVERT_E0_DIR false
+#else
+  #define INVERT_X_DIR true
+  #define INVERT_Y_DIR true
+  #define INVERT_Z_DIR false
+  #define INVERT_E0_DIR true
+#endif
 //#define INVERT_I_DIR false
 //#define INVERT_J_DIR false
 //#define INVERT_K_DIR false
-
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.
-#define INVERT_E0_DIR false
+
 #define INVERT_E1_DIR false
 #define INVERT_E2_DIR false
 #define INVERT_E3_DIR false
@@ -1340,7 +1395,7 @@
  */
 //#define Z_IDLE_HEIGHT Z_HOME_POS
 
-//#define Z_HOMING_HEIGHT  4      // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
+#define Z_HOMING_HEIGHT 7        // (mm) Minimal Z height before homing (G28) for Z clearance above the bed, clamps, ...
                                   // Be sure to have this much clearance over your Z_MAX_POS to prevent grinding.
 
 //#define Z_AFTER_HOMING  10      // (mm) Height to move to after homing Z
@@ -1356,17 +1411,36 @@
 
 // @section machine
 
-// The size of the printable area
-#define X_BED_SIZE 200
-#define Y_BED_SIZE 200
+// The size of the print bed
+#if ANY(TronxyXY2, TronxyXY2A)
+  #define X_BED_SIZE 220
+  #define Y_BED_SIZE 220
+#elif ENABLED(TronxyX5SPro)
+  #define X_BED_SIZE 330
+  #define Y_BED_SIZE 330
+#elif ANY(TronxyX3, TronxyX3A)
+  #define X_BED_SIZE 310
+  #define Y_BED_SIZE 310
+#endif
 
 // Travel limits (mm) after homing, corresponding to endstop positions.
-#define X_MIN_POS 0
-#define Y_MIN_POS 0
+#if ANY(TronxyXY2, TronxyXY2A)
+  #define X_MIN_POS -17
+  #define Y_MIN_POS -25
+  #define Z_MAX_POS 316
+#elif ENABLED(TronxyX5SPro)
+  #define X_MIN_POS 0
+  #define Y_MIN_POS 0
+  #define Z_MAX_POS 400
+#elif ANY(TronxyX3, TronxyX3A)
+  #define X_MIN_POS -17
+  #define Y_MIN_POS -25
+  #define Z_MAX_POS 330
+#endif
+
 #define Z_MIN_POS 0
 #define X_MAX_POS X_BED_SIZE
 #define Y_MAX_POS Y_BED_SIZE
-#define Z_MAX_POS 200
 //#define I_MIN_POS 0
 //#define I_MAX_POS 50
 //#define J_MIN_POS 0
@@ -1406,7 +1480,7 @@
 #endif
 
 #if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS)
-  //#define SOFT_ENDSTOPS_MENU_ITEM  // Enable/Disable software endstops from the LCD
+  #define SOFT_ENDSTOPS_MENU_ITEM  // Enable/Disable software endstops from the LCD
 #endif
 
 /**
@@ -1422,13 +1496,13 @@
  * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
  * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
  */
-//#define FILAMENT_RUNOUT_SENSOR
+#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define FIL_RUNOUT_ENABLED_DEFAULT true // Enable the sensor on startup. Override with M412 followed by M500.
   #define NUM_RUNOUT_SENSORS   1          // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
 
-  #define FIL_RUNOUT_STATE     LOW        // Pin state indicating that filament is NOT present.
-  #define FIL_RUNOUT_PULLUP               // Use internal pullup for filament runout pins.
+  #define FIL_RUNOUT_STATE     HIGH       // Pin state indicating that filament is NOT present.
+  //#define FIL_RUNOUT_PULLUP             // Use internal pullup for filament runout pins.
   //#define FIL_RUNOUT_PULLDOWN           // Use internal pulldown for filament runout pins.
   //#define WATCH_ALL_RUNOUT_SENSORS      // Execute runout script on any triggering sensor, not only for the active extruder.
                                           // This is automatically enabled for MIXING_EXTRUDERs.
@@ -1474,7 +1548,7 @@
   // After a runout is detected, continue printing this length of filament
   // before executing the runout script. Useful for a sensor at the end of
   // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead.
-  //#define FILAMENT_RUNOUT_DISTANCE_MM 25
+  #define FILAMENT_RUNOUT_DISTANCE_MM 5
 
   #ifdef FILAMENT_RUNOUT_DISTANCE_MM
     // Enable this option to use an encoder disc that toggles the runout pin
@@ -1524,7 +1598,7 @@
  */
 //#define AUTO_BED_LEVELING_3POINT
 //#define AUTO_BED_LEVELING_LINEAR
-//#define AUTO_BED_LEVELING_BILINEAR
+#define AUTO_BED_LEVELING_BILINEAR
 //#define AUTO_BED_LEVELING_UBL
 //#define MESH_BED_LEVELING
 
@@ -1533,7 +1607,7 @@
  * these options to restore the prior leveling state or to always enable
  * leveling immediately after G28.
  */
-//#define RESTORE_LEVELING_AFTER_G28
+#define RESTORE_LEVELING_AFTER_G28
 //#define ENABLE_LEVELING_AFTER_G28
 
 /**
@@ -1575,7 +1649,7 @@
   /**
    * Enable the G26 Mesh Validation Pattern tool.
    */
-  //#define G26_MESH_VALIDATION
+  #define G26_MESH_VALIDATION
   #if ENABLED(G26_MESH_VALIDATION)
     #define MESH_TEST_NOZZLE_SIZE    0.4  // (mm) Diameter of primary nozzle.
     #define MESH_TEST_LAYER_HEIGHT   0.2  // (mm) Default layer height for G26.
@@ -1591,7 +1665,7 @@
 #if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR)
 
   // Set the number of grid points per dimension.
-  #define GRID_MAX_POINTS_X 3
+  #define GRID_MAX_POINTS_X 5
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
 
   // Probe along the Y axis, advancing X after each column
@@ -1655,16 +1729,16 @@
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */
-//#define LCD_BED_LEVELING
+#define LCD_BED_LEVELING
 
 #if ENABLED(LCD_BED_LEVELING)
   #define MESH_EDIT_Z_STEP  0.025 // (mm) Step size while manually probing Z axis.
   #define LCD_PROBE_Z_RANGE 4     // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment
-  //#define MESH_EDIT_MENU        // Add a menu to edit mesh points
+  #define MESH_EDIT_MENU        // Add a menu to edit mesh points
 #endif
 
 // Add a menu item to move between bed corners for manual bed adjustment
-//#define LEVEL_BED_CORNERS
+#define LEVEL_BED_CORNERS
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets
@@ -1725,7 +1799,9 @@
  * - Allows Z homing only when XY positions are known and trusted.
  * - If stepper drivers sleep, XY homing may be required again before Z homing.
  */
-//#define Z_SAFE_HOMING
+#if ENABLED(FIX_MOUNTED_PROBE)
+  #define Z_SAFE_HOMING
+#endif
 
 #if ENABLED(Z_SAFE_HOMING)
   #define Z_SAFE_HOMING_X_POINT X_CENTER  // X point for Z homing
@@ -1810,12 +1886,12 @@
  *   M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
  *   M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
  */
-//#define EEPROM_SETTINGS     // Persistent storage with M500 and M501
+#define EEPROM_SETTINGS       // Persistent storage with M500 and M501
 //#define DISABLE_M503        // Saves ~2700 bytes of PROGMEM. Disable for release!
 #define EEPROM_CHITCHAT       // Give feedback on EEPROM commands. Disable to save PROGMEM.
 #define EEPROM_BOOT_SILENT    // Keep M503 quiet and only give errors during first load
 #if ENABLED(EEPROM_SETTINGS)
-  //#define EEPROM_AUTO_INIT  // Init EEPROM automatically on any errors.
+  #define EEPROM_AUTO_INIT  // Init EEPROM automatically on any errors.
 #endif
 
 //
@@ -1845,13 +1921,13 @@
 //
 #define PREHEAT_1_LABEL       "PLA"
 #define PREHEAT_1_TEMP_HOTEND 180
-#define PREHEAT_1_TEMP_BED     70
+#define PREHEAT_1_TEMP_BED     50
 #define PREHEAT_1_TEMP_CHAMBER 35
 #define PREHEAT_1_FAN_SPEED     0 // Value from 0 to 255
 
 #define PREHEAT_2_LABEL       "ABS"
 #define PREHEAT_2_TEMP_HOTEND 240
-#define PREHEAT_2_TEMP_BED    110
+#define PREHEAT_2_TEMP_BED    90
 #define PREHEAT_2_TEMP_CHAMBER 35
 #define PREHEAT_2_FAN_SPEED     0 // Value from 0 to 255
 
@@ -1866,11 +1942,11 @@
  *    P1  Raise the nozzle always to Z-park height.
  *    P2  Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
  */
-//#define NOZZLE_PARK_FEATURE
+#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
   // Specify a park position as { X, Y, Z_raise }
-  #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
+  #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MIN_POS + 10), 5 }
   //#define NOZZLE_PARK_X_ONLY          // X move only is required to park
   //#define NOZZLE_PARK_Y_ONLY          // Y move only is required to park
   #define NOZZLE_PARK_Z_RAISE_MIN   2   // (mm) Always raise Z by at least this distance
@@ -2083,14 +2159,14 @@
  * SD Card support is disabled by default. If your controller has an SD slot,
  * you must uncomment the following option or it won't work.
  */
-//#define SDSUPPORT
+#define SDSUPPORT
 
 /**
  * SD CARD: ENABLE CRC
  *
  * Use CRC checks and retries on the SD communication.
  */
-//#define SD_CHECK_AND_RETRY
+#define SD_CHECK_AND_RETRY
 
 /**
  * LCD Menu Items
@@ -2161,7 +2237,7 @@
 // If you have a speaker that can produce tones, enable it here.
 // By default Marlin assumes you have a buzzer with a fixed frequency.
 //
-//#define SPEAKER
+#define SPEAKER
 
 //
 // The duration and frequency for the UI feedback sound.
@@ -2567,6 +2643,11 @@
   #define USE_MKS_GREEN_UI
 #endif
 
+//
+// CR-6 OEM touch screen. A DWIN display with touch.
+//
+//#define DWIN_CREALITY_TOUCHLCD
+
 //
 // Touch-screen LCD for Malyan M200/M300 printers
 //
@@ -2692,19 +2773,19 @@
 //
 // Generic TFT with detailed options
 //
-//#define TFT_GENERIC
+#define TFT_GENERIC
 #if ENABLED(TFT_GENERIC)
   // :[ 'AUTO', 'ST7735', 'ST7789', 'ST7796', 'R61505', 'ILI9328', 'ILI9341', 'ILI9488' ]
-  #define TFT_DRIVER AUTO
+  //#define TFT_DRIVER AUTO
 
   // Interface. Enable one of the following options:
-  //#define TFT_INTERFACE_FSMC
+  #define TFT_INTERFACE_FSMC
   //#define TFT_INTERFACE_SPI
 
   // TFT Resolution. Enable one of the following options:
   //#define TFT_RES_320x240
   //#define TFT_RES_480x272
-  //#define TFT_RES_480x320
+  #define TFT_RES_480x320
 #endif
 
 /**
@@ -2718,7 +2799,7 @@
  *   root of your SD card, together with the compiled firmware.
  */
 //#define TFT_CLASSIC_UI
-//#define TFT_COLOR_UI
+#define TFT_COLOR_UI
 //#define TFT_LVGL_UI
 
 #if ENABLED(TFT_LVGL_UI)
@@ -2747,18 +2828,18 @@
 //
 // Touch Screen Settings
 //
-//#define TOUCH_SCREEN
+#define TOUCH_SCREEN // DONE BY CHITU BOARD
 #if ENABLED(TOUCH_SCREEN)
   #define BUTTON_DELAY_EDIT  50 // (ms) Button repeat delay for edit screens
   #define BUTTON_DELAY_MENU 250 // (ms) Button repeat delay for menus
 
   #define TOUCH_SCREEN_CALIBRATION
 
-  //#define TOUCH_CALIBRATION_X 12316
-  //#define TOUCH_CALIBRATION_Y -8981
-  //#define TOUCH_OFFSET_X        -43
-  //#define TOUCH_OFFSET_Y        257
-  //#define TOUCH_ORIENTATION TOUCH_LANDSCAPE
+  //#define TOUCH_CALIBRATION_X -12316
+  //#define TOUCH_CALIBRATION_Y   8981
+  //#define TOUCH_OFFSET_X         340
+  //#define TOUCH_OFFSET_Y         -20
+  #define TOUCH_ORIENTATION TOUCH_LANDSCAPE
 
   #if BOTH(TOUCH_SCREEN_CALIBRATION, EEPROM_SETTINGS)
     #define TOUCH_CALIBRATION_AUTO_SAVE // Auto save successful calibration values to EEPROM
@@ -2769,6 +2850,16 @@
   #endif
 #endif
 
+// Change colors
+// some colors are predefined, see /src/lcd/dogm/u8g_dev_tft_480~.cpp Line 160
+// or use 16bit color (e.g. 0x0000 = black, 0xFFE0 = yellow)
+// see https://ee-programming-notepad.blogspot.com/2016/10/16-bit-color-generator-picker.html
+#define TFT_MARLINUI_COLOR COLOR_WHITE  // main foreground color
+#define TFT_MARLINBG_COLOR COLOR_BLACK  // background color
+#define TFT_BTCANCEL_COLOR COLOR_RED    // cancel button
+#define TFT_BTARROWS_COLOR COLOR_WHITE  // arrows up/down
+#define TFT_BTOKMENU_COLOR COLOR_GREEN  // enter button
+
 //
 // RepRapWorld REPRAPWORLD_KEYPAD v1.1
 // https://reprapworld.com/products/electronics/ramps/keypad_v1_0_fully_assembled/
@@ -2792,7 +2883,7 @@
 // Use software PWM to drive the fan, as for the heaters. This uses a very low frequency
 // which is not as annoying as with the hardware PWM. On the other hand, if this frequency
 // is too low, you should also increment SOFT_PWM_SCALE.
-//#define FAN_SOFT_PWM
+#define FAN_SOFT_PWM
 
 // Incrementing this by 1 will double the software PWM frequency,
 // affecting heaters, and the fan if FAN_SOFT_PWM is enabled.

Marlin/Configuration_adv.h

@@ -274,11 +274,11 @@
  */
 #if ENABLED(THERMAL_PROTECTION_HOTENDS)
   #define THERMAL_PROTECTION_PERIOD 40        // Seconds
-  #define THERMAL_PROTECTION_HYSTERESIS 4     // Degrees Celsius
+  #define THERMAL_PROTECTION_HYSTERESIS 15    // Degrees Celsius
 
-  //#define ADAPTIVE_FAN_SLOWING              // Slow part cooling fan if temperature drops
+  #define ADAPTIVE_FAN_SLOWING              // Slow part cooling fan if temperature drops
   #if BOTH(ADAPTIVE_FAN_SLOWING, PIDTEMP)
-    //#define NO_FAN_SLOWING_IN_PID_TUNING    // Don't slow fan speed during M303
+    #define NO_FAN_SLOWING_IN_PID_TUNING    // Don't slow fan speed during M303
   #endif
 
   /**
@@ -293,7 +293,7 @@
    * and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set
    * below 2.
    */
-  #define WATCH_TEMP_PERIOD  20               // Seconds
+  #define WATCH_TEMP_PERIOD  40               // Seconds
   #define WATCH_TEMP_INCREASE 2               // Degrees Celsius
 #endif
 
@@ -301,13 +301,13 @@
  * Thermal Protection parameters for the bed are just as above for hotends.
  */
 #if ENABLED(THERMAL_PROTECTION_BED)
-  #define THERMAL_PROTECTION_BED_PERIOD        20 // Seconds
+  #define THERMAL_PROTECTION_BED_PERIOD        60 // Seconds
   #define THERMAL_PROTECTION_BED_HYSTERESIS     2 // Degrees Celsius
 
   /**
    * As described above, except for the bed (M140/M190/M303).
    */
-  #define WATCH_BED_TEMP_PERIOD                60 // Seconds
+  #define WATCH_BED_TEMP_PERIOD                90 // Seconds
   #define WATCH_BED_TEMP_INCREASE               2 // Degrees Celsius
 #endif
 
@@ -472,9 +472,9 @@
  * Hotend Idle Timeout
  * Prevent filament in the nozzle from charring and causing a critical jam.
  */
-//#define HOTEND_IDLE_TIMEOUT
+#define HOTEND_IDLE_TIMEOUT
 #if ENABLED(HOTEND_IDLE_TIMEOUT)
-  #define HOTEND_IDLE_TIMEOUT_SEC (5*60)    // (seconds) Time without extruder movement to trigger protection
+  #define HOTEND_IDLE_TIMEOUT_SEC (15*60)    // (seconds) Time without extruder movement to trigger protection
   #define HOTEND_IDLE_MIN_TRIGGER   180     // (°C) Minimum temperature to enable hotend protection
   #define HOTEND_IDLE_NOZZLE_TARGET   0     // (°C) Safe temperature for the nozzle after timeout
   #define HOTEND_IDLE_BED_TARGET      0     // (°C) Safe temperature for the bed after timeout
@@ -496,7 +496,7 @@
  * The fan turns on automatically whenever any driver is enabled and turns
  * off (or reduces to idle speed) shortly after drivers are turned off.
  */
-//#define USE_CONTROLLER_FAN
+#define USE_CONTROLLER_FAN
 #if ENABLED(USE_CONTROLLER_FAN)
   //#define CONTROLLER_FAN_PIN -1           // Set a custom pin for the controller fan
   //#define CONTROLLER_FAN_USE_Z_ONLY       // With this option only the Z axis is considered
@@ -584,7 +584,7 @@
  * Multiple extruders can be assigned to the same pin in which case
  * the fan will turn on when any selected extruder is above the threshold.
  */
-#define E0_AUTO_FAN_PIN -1
+#define E0_AUTO_FAN_PIN FAN2_PIN
 #define E1_AUTO_FAN_PIN -1
 #define E2_AUTO_FAN_PIN -1
 #define E3_AUTO_FAN_PIN -1
@@ -1292,13 +1292,13 @@
   #endif
 
   // Scroll a longer status message into view
-  //#define STATUS_MESSAGE_SCROLLING
+  #define STATUS_MESSAGE_SCROLLING
 
   // On the Info Screen, display XY with one decimal place when possible
   //#define LCD_DECIMAL_SMALL_XY
 
   // Add an 'M73' G-code to set the current percentage
-  //#define LCD_SET_PROGRESS_MANUALLY
+  #define LCD_SET_PROGRESS_MANUALLY
 
   // Show the E position (filament used) during printing
   //#define LCD_SHOW_E_TOTAL
@@ -1449,10 +1449,10 @@
   //#define UTF_FILENAME_SUPPORT
 
   // This allows hosts to request long names for files and folders with M33
-  //#define LONG_FILENAME_HOST_SUPPORT
+  #define LONG_FILENAME_HOST_SUPPORT
 
   // Enable this option to scroll long filenames in the SD card menu
-  //#define SCROLL_LONG_FILENAMES
+  #define SCROLL_LONG_FILENAMES
 
   // Leave the heaters on after Stop Print (not recommended!)
   //#define SD_ABORT_NO_COOLDOWN
@@ -1641,7 +1641,7 @@
   //#define STATUS_ALT_FAN_BITMAP     // Use the alternative fan bitmap
   //#define STATUS_FAN_FRAMES 3       // :[0,1,2,3,4] Number of fan animation frames
   //#define STATUS_HEAT_PERCENT       // Show heating in a progress bar
-  //#define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~‭3260 (or ~940) bytes of PROGMEM.
+  #define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~‭3260 (or ~940) bytes of PROGMEM.
 
   // Frivolous Game Options
   //#define MARLIN_BRICKOUT
@@ -1858,18 +1858,18 @@
  *
  * Warning: Does not respect endstops!
  */
-//#define BABYSTEPPING
+#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
-  //#define INTEGRATED_BABYSTEPPING         // EXPERIMENTAL integration of babystepping into the Stepper ISR
+  #define INTEGRATED_BABYSTEPPING         // EXPERIMENTAL integration of babystepping into the Stepper ISR
   //#define BABYSTEP_WITHOUT_HOMING
-  //#define BABYSTEP_ALWAYS_AVAILABLE       // Allow babystepping at all times (not just during movement).
+  #define BABYSTEP_ALWAYS_AVAILABLE       // Allow babystepping at all times (not just during movement).
   //#define BABYSTEP_XY                     // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false           // Change if Z babysteps should go the other way
   //#define BABYSTEP_MILLIMETER_UNITS       // Specify BABYSTEP_MULTIPLICATOR_(XY|Z) in mm instead of micro-steps
-  #define BABYSTEP_MULTIPLICATOR_Z  1       // (steps or mm) Steps or millimeter distance for each Z babystep
+  #define BABYSTEP_MULTIPLICATOR_Z  10       // (steps or mm) Steps or millimeter distance for each Z babystep
   #define BABYSTEP_MULTIPLICATOR_XY 1       // (steps or mm) Steps or millimeter distance for each XY babystep
 
-  //#define DOUBLECLICK_FOR_Z_BABYSTEPPING  // Double-click on the Status Screen for Z Babystepping.
+  #define DOUBLECLICK_FOR_Z_BABYSTEPPING  // Double-click on the Status Screen for Z Babystepping.
   #if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING)
     #define DOUBLECLICK_MAX_INTERVAL 1250   // Maximum interval between clicks, in milliseconds.
                                             // Note: Extra time may be added to mitigate controller latency.
@@ -1880,8 +1880,9 @@
   #endif
 
   //#define BABYSTEP_DISPLAY_TOTAL          // Display total babysteps since last G28
-
-  //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
+  #if NONE(TronxyX3, TronxyXY2)
+    #define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
+  #endif
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets
     //#define BABYSTEP_ZPROBE_GFX_OVERLAY   // Enable graphical overlay on Z-offset editor
@@ -2206,7 +2207,7 @@
  * Currently handles M108, M112, M410, M876
  * NOTE: Not yet implemented for all platforms.
  */
-//#define EMERGENCY_PARSER
+#define EMERGENCY_PARSER
 
 /**
  * Realtime Reporting (requires EMERGENCY_PARSER)
@@ -2383,7 +2384,7 @@
  *
  * Enable PARK_HEAD_ON_PAUSE to add the G-code M125 Pause and Park.
  */
-//#define ADVANCED_PAUSE_FEATURE
+#define ADVANCED_PAUSE_FEATURE
 #if ENABLED(ADVANCED_PAUSE_FEATURE)
   #define PAUSE_PARK_RETRACT_FEEDRATE         60  // (mm/s) Initial retract feedrate.
   #define PAUSE_PARK_RETRACT_LENGTH            2  // (mm) Initial retract.
@@ -2421,7 +2422,7 @@
   #define FILAMENT_CHANGE_ALERT_BEEPS         10  // Number of alert beeps to play when a response is needed.
   #define PAUSE_PARK_NO_STEPPER_TIMEOUT           // Enable for XYZ steppers to stay powered on during filament change.
 
-  //#define PARK_HEAD_ON_PAUSE                    // Park the nozzle during pause and filament change.
+  #define PARK_HEAD_ON_PAUSE                    // Park the nozzle during pause and filament change.
   //#define HOME_BEFORE_FILAMENT_CHANGE           // If needed, home before parking for filament change
 
   //#define FILAMENT_LOAD_UNLOAD_GCODES           // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
@@ -3493,6 +3494,16 @@
  */
 //#define LASER_SYNCHRONOUS_M106_M107
 
+/**
+ * Synchronous Laser Control with M106/M107
+ *
+ * By default M106 / M107 applies the new fan speed immediately. This is fine
+ * for fans, but unsuitable for a PWM/TTL laser attached to the fan header.
+ *
+ * NOTE: This option sacrifices some cooling fan speed options.
+ */
+//#define LASER_SYNCHRONOUS_M106_M107
+
 /**
  * Coolant Control
  *
@@ -3820,11 +3831,11 @@
  * Host Prompt Support enables Marlin to use the host for user prompts so
  * filament runout and other processes can be managed from the host side.
  */
-//#define HOST_ACTION_COMMANDS
+#define HOST_ACTION_COMMANDS
 #if ENABLED(HOST_ACTION_COMMANDS)
   //#define HOST_PAUSE_M76
-  //#define HOST_PROMPT_SUPPORT
-  //#define HOST_START_MENU_ITEM  // Add a menu item that tells the host to start
+  #define HOST_PROMPT_SUPPORT
+  #define HOST_START_MENU_ITEM  // Add a menu item that tells the host to start
 #endif
 
 /**
@@ -4120,6 +4131,8 @@
     #define MMU2_CAN_LOAD_INCREMENT_SEQUENCE \
       { -MMU2_CAN_LOAD_INCREMENT, MMU2_CAN_LOAD_FEEDRATE }
 
+    // Continue unloading if sensor detects filament after the initial unload move
+    //#define MMU_IR_UNLOAD_MOVE
   #else
 
     /**
@@ -4173,7 +4186,7 @@
 //
 // M43 - display pin status, toggle pins, watch pins, watch endstops & toggle LED, test servo probe
 //
-//#define PINS_DEBUGGING
+#define PINS_DEBUGGING
 
 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE