Merge branch 'bugfix-2.0.x' into TMSX4_2.0_Bleeding

Marlin/Configuration.h

@@ -1,3 +1,38 @@
+//#define PetsfangMicroswiss
+//#define BondtechBMG
+//#define CR10SPro_GearedExtruder
+//#define E3DV6
+//#define Mosquito
+
+//#define FilamentSensorStd
+//#define FilamentSensorLerdge
+//#define FilamentEncoder
+
+//#define STOCK_2208 // V2 Stock Board with TMC2208 Drivers
+//#define SKR13 // 32 bit board - assumes 2208 drivers
+//#define SKR14
+//#define SKR14Turbo
+//#define SKR_2209
+//#define E_8825
+//#define SKR_UART // Configure SKR board with drivers in UART mode
+
+#define SX2 // Small formfactor 200mm machine
+
+#define DUAL_Z
+//#define GRAPHICSLCD
+#define UBL
+
+
+#if ANY(SKR13, SKR14, SKR14Turbo)
+  #define SKRLPCBoard
+#endif
+
+//#define SlicePT1000
+//#define SliceDualHeater
+
+// Power outputs EFBF or EFBE
+//#define HEATER_1_PIN                           7
+
 /**
  * Marlin 3D Printer Firmware
  * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
@@ -21,6 +56,9 @@
  */
 #pragma once
 
+#if DISABLED(SKRLPCBoard)
+  #define Y_STOP_PIN 14
+#endif
 /**
  * Configuration.h
  *
@@ -70,8 +108,8 @@
 // @section info
 
 // Author info of this build printed to the host during boot and M115
-#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
-//#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
+#define STRING_CONFIG_H_AUTHOR "Tinymachines3D" // Who made the changes.
+#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
 
 /**
  * *** VENDORS PLEASE READ ***
@@ -87,12 +125,13 @@
 // Show the Marlin bootscreen on startup. ** ENABLE FOR PRODUCTION **
 #define SHOW_BOOTSCREEN
 
+#if ENABLED(GRAPHICSLCD)
 // Show the bitmap in Marlin/_Bootscreen.h on startup.
-//#define SHOW_CUSTOM_BOOTSCREEN
+#define SHOW_CUSTOM_BOOTSCREEN
 
 // Show the bitmap in Marlin/_Statusscreen.h on the status screen.
-//#define CUSTOM_STATUS_SCREEN_IMAGE
-
+#define CUSTOM_STATUS_SCREEN_IMAGE
+#endif
 // @section machine
 
 /**
@@ -110,8 +149,9 @@
  * Currently Ethernet (-2) is only supported on Teensy 4.1 boards.
  * :[-2, -1, 0, 1, 2, 3, 4, 5, 6, 7]
  */
-//#define SERIAL_PORT_2 -1
-
+#if ENABLED(SKRLPCBoard)
+  #define SERIAL_PORT_2 -1
+#endif
 /**
  * This setting determines the communication speed of the printer.
  *
@@ -128,11 +168,24 @@
 
 // Choose the name from boards.h that matches your setup
 #ifndef MOTHERBOARD
-  #define MOTHERBOARD BOARD_RAMPS_14_EFB
+  #if ENABLED(SKR13)
+    #define MOTHERBOARD BOARD_BTT_SKR_V1_3
+  #elif ENABLED(SKR14)
+    #define MOTHERBOARD BOARD_BTT_SKR_V1_4
+  #elif ENABLED(SKR14Turbo)
+    #define MOTHERBOARD BOARD_BTT_SKR_V1_4_TURBO
+  #else
+    #define MOTHERBOARD BOARD_RAMPS_14_EFB
+  #endif
 #endif
 
 // Name displayed in the LCD "Ready" message and Info menu
-//#define CUSTOM_MACHINE_NAME "3D Printer"
+#if ENABLED(SX2)
+    #define CUSTOM_MACHINE_NAME "TM3D SX2"
+  #else
+    #define CUSTOM_MACHINE_NAME "TM3D SX4"
+#endif
+
 
 // Printer's unique ID, used by some programs to differentiate between machines.
 // Choose your own or use a service like https://www.uuidgenerator.net/version4
@@ -408,15 +461,27 @@
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  */
-#define TEMP_SENSOR_0 1
-#define TEMP_SENSOR_1 0
+#if ENABLED(SlicePT1000)
+  #define TEMP_SENSOR_0 1047
+#elif ENABLED(Mosquito)
+  #define TEMP_SENSOR_0 67
+#elif ENABLED(E3DV6)
+  #define TEMP_SENSOR_0 5
+#else
+  #define TEMP_SENSOR_0 1
+#endif
+#if ENABLED(SliceDualHeater)
+  #define TEMP_SENSOR_1 0
+#else
+  #define TEMP_SENSOR_1 0
+#endif
 #define TEMP_SENSOR_2 0
 #define TEMP_SENSOR_3 0
 #define TEMP_SENSOR_4 0
 #define TEMP_SENSOR_5 0
 #define TEMP_SENSOR_6 0
 #define TEMP_SENSOR_7 0
-#define TEMP_SENSOR_BED 0
+#define TEMP_SENSOR_BED 11
 #define TEMP_SENSOR_PROBE 0
 #define TEMP_SENSOR_CHAMBER 0
 
@@ -432,14 +497,16 @@
 
 // Use temp sensor 1 as a redundant sensor with sensor 0. If the readings
 // from the two sensors differ too much the print will be aborted.
-//#define TEMP_SENSOR_1_AS_REDUNDANT
+#if ENABLED(SliceDualHeater)
+  //#define TEMP_SENSOR_1_AS_REDUNDANT
+#endif
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-#define TEMP_RESIDENCY_TIME     10  // (seconds) Time to wait for hotend to "settle" in M109
+#define TEMP_RESIDENCY_TIME     3  // (seconds) Time to wait for hotend to "settle" in M109
 #define TEMP_WINDOW              1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_HYSTERESIS          3  // (°C) Temperature proximity considered "close enough" to the target
 
-#define TEMP_BED_RESIDENCY_TIME 10  // (seconds) Time to wait for bed to "settle" in M190
+#define TEMP_BED_RESIDENCY_TIME 5  // (seconds) Time to wait for bed to "settle" in M190
 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
@@ -458,7 +525,7 @@
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 // (Use MINTEMP for thermistor short/failure protection.)
-#define HEATER_0_MAXTEMP 275
+#define HEATER_0_MAXTEMP 305
 #define HEATER_1_MAXTEMP 275
 #define HEATER_2_MAXTEMP 275
 #define HEATER_3_MAXTEMP 275
@@ -466,7 +533,7 @@
 #define HEATER_5_MAXTEMP 275
 #define HEATER_6_MAXTEMP 275
 #define HEATER_7_MAXTEMP 275
-#define BED_MAXTEMP      150
+#define BED_MAXTEMP      125
 
 //===========================================================================
 //============================= PID Settings ================================
@@ -480,22 +547,35 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
+  #define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  #define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
+  #define PID_FUNCTIONAL_RANGE 10 // If the temperature difference between the target temperature and the actual temperature
+                                  // is more than PID_FUNCTIONAL_RANGE then the PID will be shut off and the heater will be set to min/max.
 
-  #if ENABLED(PID_PARAMS_PER_HOTEND)
-    // Specify between 1 and HOTENDS values per array.
-    // If fewer than EXTRUDER values are provided, the last element will be repeated.
-    #define DEFAULT_Kp_LIST {  22.20,  22.20 }
-    #define DEFAULT_Ki_LIST {   1.08,   1.08 }
-    #define DEFAULT_Kd_LIST { 114.00, 114.00 }
+  // If you are using a pre-configured hotend then you can use one of the value sets by uncommenting it
+
+  // Ultimaker
+  #if ENABLED(PetsfangMicroswiss)
+    #define DEFAULT_Kp 18.74
+    #define DEFAULT_Ki 0.71
+    #define DEFAULT_Kd 123.56
   #else
-    #define DEFAULT_Kp  22.20
-    #define DEFAULT_Ki   1.08
-    #define DEFAULT_Kd 114.00
+    #define DEFAULT_Kp 10.59
+    #define DEFAULT_Ki 0.37
+    #define DEFAULT_Kd 75.24
   #endif
+  // MakerGear
+  //#define DEFAULT_Kp 7.0
+  //#define DEFAULT_Ki 0.1
+  //#define DEFAULT_Kd 12
+
+  // Mendel Parts V9 on 12V
+  //#define DEFAULT_Kp 63.0
+  //#define DEFAULT_Ki 2.25
+  //#define DEFAULT_Kd 440
+
 #endif // PIDTEMP
 
 //===========================================================================
@@ -596,7 +676,7 @@
 
 // Enable one of the options below for CoreXY, CoreXZ, or CoreYZ kinematics,
 // either in the usual order or reversed
-//#define COREXY
+#define COREXY
 //#define COREXZ
 //#define COREYZ
 //#define COREYX
@@ -614,10 +694,10 @@
 // Almost all printers will be using one per axis. Probes will use one or more of the
 // extra connectors. Leave undefined any used for non-endstop and non-probe purposes.
 #define USE_XMIN_PLUG
-#define USE_YMIN_PLUG
+//#define USE_YMIN_PLUG
 #define USE_ZMIN_PLUG
 //#define USE_XMAX_PLUG
-//#define USE_YMAX_PLUG
+#define USE_YMAX_PLUG
 //#define USE_ZMAX_PLUG
 
 // Enable pullup for all endstops to prevent a floating state
@@ -647,13 +727,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING false // set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -673,16 +753,64 @@
  *          TMC5130, TMC5130_STANDALONE, TMC5160, TMC5160_STANDALONE
  * :['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'L6474', 'POWERSTEP01', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', 'TMC2160', 'TMC2160_STANDALONE', 'TMC2208', 'TMC2208_STANDALONE', 'TMC2209', 'TMC2209_STANDALONE', 'TMC26X', 'TMC26X_STANDALONE', 'TMC2660', 'TMC2660_STANDALONE', 'TMC5130', 'TMC5130_STANDALONE', 'TMC5160', 'TMC5160_STANDALONE']
  */
-#define X_DRIVER_TYPE  A4988
-#define Y_DRIVER_TYPE  A4988
-#define Z_DRIVER_TYPE  A4988
+
+#if ENABLED(SKRLPCBoard, E_8825)
+  #define E0_DRIVER_TYPE DRV8825
+  #define E1_DRIVER_TYPE DRV8825
+#endif
+
+#if ANY(SKRLPCBoard, STOCK_2208) && DISABLED(SKR_UART)
+  #if ENABLED(SKR_2209)
+    #define X_DRIVER_TYPE  TMC2209_STANDALONE
+    #define Y_DRIVER_TYPE  TMC2209_STANDALONE
+    #define Z_DRIVER_TYPE  TMC2209_STANDALONE
+    #define Z2_DRIVER_TYPE TMC2209_STANDALONE
+    #if DISABLED(E_8825)
+      #define E0_DRIVER_TYPE TMC2209_STANDALONE
+      #define E1_DRIVER_TYPE TMC2209_STANDALONE
+    #endif
+  #else
+    #define X_DRIVER_TYPE  TMC2208_STANDALONE
+    #define Y_DRIVER_TYPE  TMC2208_STANDALONE
+    #define Z_DRIVER_TYPE  TMC2208_STANDALONE
+    #define Z2_DRIVER_TYPE TMC2208_STANDALONE
+    #if DISABLED(E_8825)
+      #define E0_DRIVER_TYPE TMC2208_STANDALONE
+      #define E1_DRIVER_TYPE TMC2208_STANDALONE
+    #endif
+  #endif
+#elif ENABLED(SKRLPCBoard, SKR_UART)
+  #if ENABLED(SKR_2209)
+    #define X_DRIVER_TYPE  TMC2209
+    #define Y_DRIVER_TYPE  TMC2209
+    #define Z_DRIVER_TYPE  TMC2209
+    #define Z2_DRIVER_TYPE TMC2209
+    #if DISABLED(E_8825)
+      #define E0_DRIVER_TYPE TMC2209
+      #define E1_DRIVER_TYPE TMC2209
+    #endif
+  #else
+    #define X_DRIVER_TYPE  TMC2208
+    #define Y_DRIVER_TYPE  TMC2208
+    #define Z_DRIVER_TYPE  TMC2208
+    #define Z2_DRIVER_TYPE TMC2208
+    #if DISABLED(E_8825)
+      #define E0_DRIVER_TYPE TMC2208
+      #define E1_DRIVER_TYPE TMC2208
+    #endif
+  #endif
+#else
+  #define X_DRIVER_TYPE  A4988
+  #define Y_DRIVER_TYPE  A4988
+  #define Z_DRIVER_TYPE  A4988
+  #define Z2_DRIVER_TYPE A4988
+  #define E0_DRIVER_TYPE A4988
+  #define E1_DRIVER_TYPE A4988
+#endif
 //#define X2_DRIVER_TYPE A4988
 //#define Y2_DRIVER_TYPE A4988
-//#define Z2_DRIVER_TYPE A4988
 //#define Z3_DRIVER_TYPE A4988
 //#define Z4_DRIVER_TYPE A4988
-#define E0_DRIVER_TYPE A4988
-//#define E1_DRIVER_TYPE A4988
 //#define E2_DRIVER_TYPE A4988
 //#define E3_DRIVER_TYPE A4988
 //#define E4_DRIVER_TYPE A4988
@@ -706,7 +834,7 @@
  *
  * :[2,3,4,5,6,7]
  */
-//#define ENDSTOP_NOISE_THRESHOLD 2
+#define ENDSTOP_NOISE_THRESHOLD 2
 
 // Check for stuck or disconnected endstops during homing moves.
 //#define DETECT_BROKEN_ENDSTOP
@@ -736,18 +864,26 @@
  * Override with M92
  *                                      X, Y, Z, E0 [, E1[, E2...]]
  */
-#define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 80, 400, 500 }
+#if ENABLED(BondtechBMG)
+  #define EStepsmm 415
+#elif ENABLED(CR10SPro_GearedExtruder)
+  #define EStepsmm 140
+#else
+  #define EStepsmm 100.3
+#endif
 
+
+  #define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 80, 400, EStepsmm }
 /**
  * Default Max Feed Rate (mm/s)
  * Override with M203
  *                                      X, Y, Z, E0 [, E1[, E2...]]
  */
-#define DEFAULT_MAX_FEEDRATE          { 300, 300, 5, 25 }
+#define DEFAULT_MAX_FEEDRATE          { 500, 500, 5, 70 }
 
-//#define LIMITED_MAX_FR_EDITING        // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
+#define LIMITED_MAX_FR_EDITING        // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
 #if ENABLED(LIMITED_MAX_FR_EDITING)
-  #define MAX_FEEDRATE_EDIT_VALUES    { 600, 600, 10, 50 } // ...or, set your own edit limits
+  #define MAX_FEEDRATE_EDIT_VALUES    { 1000, 1000, 10, 150 } // ...or, set your own edit limits
 #endif
 
 /**
@@ -756,11 +892,11 @@
  * Override with M201
  *                                      X, Y, Z, E0 [, E1[, E2...]]
  */
-#define DEFAULT_MAX_ACCELERATION      { 3000, 3000, 100, 10000 }
+#define DEFAULT_MAX_ACCELERATION      { 1500, 1500, 50, 2000 }
 
-//#define LIMITED_MAX_ACCEL_EDITING     // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
+#define LIMITED_MAX_ACCEL_EDITING     // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
 #if ENABLED(LIMITED_MAX_ACCEL_EDITING)
-  #define MAX_ACCEL_EDIT_VALUES       { 6000, 6000, 200, 20000 } // ...or, set your own edit limits
+  #define MAX_ACCEL_EDIT_VALUES       { 2500, 2500, 125, 5000 } // ...or, set your own edit limits
 #endif
 
 /**
@@ -771,9 +907,9 @@
  *   M204 R    Retract Acceleration
  *   M204 T    Travel Acceleration
  */
-#define DEFAULT_ACCELERATION          3000    // X, Y, Z and E acceleration for printing moves
-#define DEFAULT_RETRACT_ACCELERATION  3000    // E acceleration for retracts
-#define DEFAULT_TRAVEL_ACCELERATION   3000    // X, Y, Z acceleration for travel (non printing) moves
+#define DEFAULT_ACCELERATION          1000    // X, Y, Z and E acceleration for printing moves
+#define DEFAULT_RETRACT_ACCELERATION  1500    // E acceleration for retracts
+#define DEFAULT_TRAVEL_ACCELERATION   1000    // X, Y, Z acceleration for travel (non printing) moves
 
 /**
  * Default Jerk limits (mm/s)
@@ -783,7 +919,7 @@
  * When changing speed and direction, if the difference is less than the
  * value set here, it may happen instantaneously.
  */
-//#define CLASSIC_JERK
+#define CLASSIC_JERK
 #if ENABLED(CLASSIC_JERK)
   #define DEFAULT_XJERK 10.0
   #define DEFAULT_YJERK 10.0
@@ -820,7 +956,7 @@
  *
  * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained
  */
-//#define S_CURVE_ACCELERATION
+#define S_CURVE_ACCELERATION
 
 //===========================================================================
 //============================= Z Probe Options =============================
@@ -894,7 +1030,7 @@
 /**
  * The BLTouch probe uses a Hall effect sensor and emulates a servo.
  */
-//#define BLTOUCH
+#define BLTOUCH
 
 /**
  * Touch-MI Probe by hotends.fr
@@ -986,14 +1122,26 @@
  *     |    [-]    |
  *     O-- FRONT --+
  */
-#define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
+#if ENABLED(PetsfangMicroswiss)
+  #define NOZZLE_TO_PROBE_OFFSET { -42, -5, 0 }
+#elif ENABLED(E3DV6)
+  #define NOZZLE_TO_PROBE_OFFSET { 36, 15, 0 }
+#elif ENABLED(Mosquito)
+  #define NOZZLE_TO_PROBE_OFFSET { 0, 26, 0 }
+#else
+  #define NOZZLE_TO_PROBE_OFFSET { 37, -10, 0 }
+#endif
 
 // Most probes should stay away from the edges of the bed, but
 // with NOZZLE_AS_PROBE this can be negative for a wider probing area.
-#define PROBING_MARGIN 10
+#if ENABLED(Mosquito)
+  #define PROBING_MARGIN 5
+#else
+  #define PROBING_MARGIN 5
+#endif
 
-// X and Y axis travel speed (mm/min) between probes
-#define XY_PROBE_SPEED (133*60)
+// X and Y axis travel speed (mm/m) between probes
+#define XY_PROBE_SPEED 5000
 
 // Feedrate (mm/min) for the first approach when double-probing (MULTIPLE_PROBING == 2)
 #define Z_PROBE_SPEED_FAST (4*60)
@@ -1037,7 +1185,7 @@
  * A total of 2 does fast/slow probes with a weighted average.
  * A total of 3 or more adds more slow probes, taking the average.
  */
-//#define MULTIPLE_PROBING 2
+#define MULTIPLE_PROBING 2
 //#define EXTRA_PROBING    1
 
 /**
@@ -1059,11 +1207,11 @@
 #define Z_CLEARANCE_MULTI_PROBE     5 // Z Clearance between multiple probes
 //#define Z_AFTER_PROBING           5 // Z position after probing is done
 
-#define Z_PROBE_LOW_POINT          -2 // Farthest distance below the trigger-point to go before stopping
+#define Z_PROBE_LOW_POINT          -3 // Farthest distance below the trigger-point to go before stopping
 
 // For M851 give a range for adjusting the Z probe offset
-#define Z_PROBE_OFFSET_RANGE_MIN -20
-#define Z_PROBE_OFFSET_RANGE_MAX 20
+#define Z_PROBE_OFFSET_RANGE_MIN -9
+#define Z_PROBE_OFFSET_RANGE_MAX 9
 
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
@@ -1120,14 +1268,24 @@
 // @section machine
 
 // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
-#define INVERT_X_DIR false
-#define INVERT_Y_DIR true
-#define INVERT_Z_DIR false
+#if ANY(SKRLPCBoard, STOCK_2208)
+  #define INVERT_X_DIR true
+  #define INVERT_Y_DIR true
+  #define INVERT_Z_DIR true
+#else
+  #define INVERT_X_DIR false
+  #define INVERT_Y_DIR false
+  #define INVERT_Z_DIR false
+#endif
 
 // @section extruder
 
 // For direct drive extruder v9 set to true, for geared extruder set to false.
-#define INVERT_E0_DIR false
+#if (ENABLED(BondtechBMG, CR10SPro_GearedExtruder) && DISABLED(SKRLPCBoard)) || (DISABLED(BondtechBM, CR10SPro_GearedExtruderG) && ANY(SKRLPCBoard, STOCK_2208))
+  #define INVERT_E0_DIR true
+#else
+  #define INVERT_E0_DIR false
+#endif
 #define INVERT_E1_DIR false
 #define INVERT_E2_DIR false
 #define INVERT_E3_DIR false
@@ -1150,14 +1308,30 @@
 // Direction of endstops when homing; 1=MAX, -1=MIN
 // :[-1,1]
 #define X_HOME_DIR -1
-#define Y_HOME_DIR -1
+#define Y_HOME_DIR  1
 #define Z_HOME_DIR -1
 
 // @section machine
 
 // The size of the print bed
-#define X_BED_SIZE 200
-#define Y_BED_SIZE 200
+ #if ENABLED(Mosquito)
+  #define XCarriageModifier 10
+  #define YCarriageModifier 35
+ #elif ENABLED(PetsfangMicroswiss)
+  #define XCarriageModifier 10
+  #define YCarriageModifier 10
+#else
+  #define XCarriageModifier 0
+  #define YCarriageModifier 0
+#endif
+
+#if ENABLED(SX2)
+  #define X_BED_SIZE 248 - XCarriageModifier
+  #define Y_BED_SIZE 238 - YCarriageModifier
+#else
+  #define X_BED_SIZE 398 - XCarriageModifier
+  #define Y_BED_SIZE 390 - YCarriageModifier
+#endif
 
 // Travel limits (mm) after homing, corresponding to endstop positions.
 #define X_MIN_POS 0
@@ -1165,8 +1339,11 @@
 #define Z_MIN_POS 0
 #define X_MAX_POS X_BED_SIZE
 #define Y_MAX_POS Y_BED_SIZE
-#define Z_MAX_POS 200
-
+#if DISABLED(SX2)
+  #define Z_MAX_POS 500
+#else
+  #define Z_MAX_POS 250
+#endif
 /**
  * Software Endstops
  *
@@ -1209,14 +1386,24 @@
  * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
  * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
  */
-//#define FILAMENT_RUNOUT_SENSOR
+ #if ANY(FilamentSensorStd, FilamentSensorLerdge, FilamentEncoder)
+  #define FILAMENT_RUNOUT_SENSOR
+#endif
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define FIL_RUNOUT_ENABLED_DEFAULT true // Enable the sensor on startup. Override with M412 followed by M500.
   #define NUM_RUNOUT_SENSORS   1          // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
 
-  #define FIL_RUNOUT_STATE     LOW        // Pin state indicating that filament is NOT present.
-  #define FIL_RUNOUT_PULLUP               // Use internal pullup for filament runout pins.
-  //#define FIL_RUNOUT_PULLDOWN           // Use internal pulldown for filament runout pins.
+  #if ENABLED(FilamentSensorLerdge)
+   #define FIL_RUNOUT_STATE     LOW        // Pin state indicating that filament is NOT present.
+ #else
+   #define FIL_RUNOUT_STATE     HIGH        // Pin state indicating that filament is NOT present.
+ #endif
+  #define FIL_RUNOUT_PULLUP          // Use internal pullup for filament runout pins.
+  //#define FIL_RUNOUT_PULLDOWN      // Use internal pulldown for filament runout pins.
+
+  #if DISABLED(SKRLPCBoard)
+    #define FIL_RUNOUT_PIN 2
+  #endif
 
   // Override individually if the runout sensors vary
   //#define FIL_RUNOUT1_STATE LOW
@@ -1258,13 +1445,19 @@
   // After a runout is detected, continue printing this length of filament
   // before executing the runout script. Useful for a sensor at the end of
   // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead.
-  //#define FILAMENT_RUNOUT_DISTANCE_MM 25
+  #if ENABLED(FilamentEncoder)
+    #define FILAMENT_RUNOUT_DISTANCE_MM 15
+  #else
+    #define FILAMENT_RUNOUT_DISTANCE_MM 5
+  #endif
 
   #ifdef FILAMENT_RUNOUT_DISTANCE_MM
     // Enable this option to use an encoder disc that toggles the runout pin
     // as the filament moves. (Be sure to set FILAMENT_RUNOUT_DISTANCE_MM
     // large enough to avoid false positives.)
-    //#define FILAMENT_MOTION_SENSOR
+    #if ENABLED(FilamentEncoder)
+      #define FILAMENT_MOTION_SENSOR
+    #endif
   #endif
 #endif
 
@@ -1308,8 +1501,11 @@
  */
 //#define AUTO_BED_LEVELING_3POINT
 //#define AUTO_BED_LEVELING_LINEAR
-//#define AUTO_BED_LEVELING_BILINEAR
-//#define AUTO_BED_LEVELING_UBL
+#if DISABLED(UBL)
+  #define AUTO_BED_LEVELING_BILINEAR
+#else
+  #define AUTO_BED_LEVELING_UBL
+#endif
 //#define MESH_BED_LEVELING
 
 /**
@@ -1317,7 +1513,7 @@
  * these options to restore the prior leveling state or to always enable
  * leveling immediately after G28.
  */
-//#define RESTORE_LEVELING_AFTER_G28
+#define RESTORE_LEVELING_AFTER_G28
 //#define ENABLE_LEVELING_AFTER_G28
 
 /**
@@ -1354,7 +1550,7 @@
   /**
    * Enable the G26 Mesh Validation Pattern tool.
    */
-  //#define G26_MESH_VALIDATION
+  #define G26_MESH_VALIDATION
   #if ENABLED(G26_MESH_VALIDATION)
     #define MESH_TEST_NOZZLE_SIZE    0.4  // (mm) Diameter of primary nozzle.
     #define MESH_TEST_LAYER_HEIGHT   0.2  // (mm) Default layer height for the G26 Mesh Validation Tool.
@@ -1369,7 +1565,11 @@
 #if EITHER(AUTO_BED_LEVELING_LINEAR, AUTO_BED_LEVELING_BILINEAR)
 
   // Set the number of grid points per dimension.
-  #define GRID_MAX_POINTS_X 3
+  #if ENABLED(SX2)
+    #define GRID_MAX_POINTS_X 5
+  #else
+    #define GRID_MAX_POINTS_X 10
+  #endif
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
 
   // Probe along the Y axis, advancing X after each column
@@ -1429,22 +1629,22 @@
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */
-//#define LCD_BED_LEVELING
+#define LCD_BED_LEVELING
 
 #if ENABLED(LCD_BED_LEVELING)
   #define MESH_EDIT_Z_STEP  0.025 // (mm) Step size while manually probing Z axis.
   #define LCD_PROBE_Z_RANGE 4     // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment
-  //#define MESH_EDIT_MENU        // Add a menu to edit mesh points
+  #define MESH_EDIT_MENU        // Add a menu to edit mesh points
 #endif
 
 // Add a menu item to move between bed corners for manual bed adjustment
-//#define LEVEL_BED_CORNERS
+#define LEVEL_BED_CORNERS
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets
   #define LEVEL_CORNERS_HEIGHT      0.0   // (mm) Z height of nozzle at leveling points
   #define LEVEL_CORNERS_Z_HOP       4.0   // (mm) Z height of nozzle between leveling points
-  //#define LEVEL_CENTER_TOO              // Move to the center after the last corner
+  #define LEVEL_CENTER_TOO              // Move to the center after the last corner
   //#define LEVEL_CORNERS_USE_PROBE
   #if ENABLED(LEVEL_CORNERS_USE_PROBE)
     #define LEVEL_CORNERS_PROBE_TOLERANCE 0.1
@@ -1479,7 +1679,7 @@
 // - Move the Z probe (or nozzle) to a defined XY point before Z Homing.
 // - Prevent Z homing when the Z probe is outside bed area.
 //
-//#define Z_SAFE_HOMING
+#define Z_SAFE_HOMING
 
 #if ENABLED(Z_SAFE_HOMING)
   #define Z_SAFE_HOMING_X_POINT X_CENTER  // X point for Z homing
@@ -1487,7 +1687,7 @@
 #endif
 
 // Homing speeds (mm/min)
-#define HOMING_FEEDRATE_MM_M { (50*60), (50*60), (4*60) }
+#define HOMING_FEEDRATE_MM_M { (50*60), (50*60), (6*60) }
 
 // Validate that endstops are triggered on homing moves
 #define VALIDATE_HOMING_ENDSTOPS
@@ -1564,12 +1764,12 @@
  *   M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
  *   M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
  */
-//#define EEPROM_SETTINGS     // Persistent storage with M500 and M501
+#define EEPROM_SETTINGS     // Persistent storage with M500 and M501
 //#define DISABLE_M503        // Saves ~2700 bytes of PROGMEM. Disable for release!
 #define EEPROM_CHITCHAT       // Give feedback on EEPROM commands. Disable to save PROGMEM.
 #define EEPROM_BOOT_SILENT    // Keep M503 quiet and only give errors during first load
 #if ENABLED(EEPROM_SETTINGS)
-  //#define EEPROM_AUTO_INIT  // Init EEPROM automatically on any errors.
+  #define EEPROM_AUTO_INIT  // Init EEPROM automatically on any errors.
 #endif
 
 //
@@ -1616,16 +1816,16 @@
  *    P1  Raise the nozzle always to Z-park height.
  *    P2  Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
  */
-//#define NOZZLE_PARK_FEATURE
+#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
   // Specify a park position as { X, Y, Z_raise }
-  #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
+  #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MIN_POS + 30), 10 }
   //#define NOZZLE_PARK_X_ONLY          // X move only is required to park
   //#define NOZZLE_PARK_Y_ONLY          // Y move only is required to park
   #define NOZZLE_PARK_Z_RAISE_MIN   2   // (mm) Always raise Z by at least this distance
   #define NOZZLE_PARK_XY_FEEDRATE 100   // (mm/s) X and Y axes feedrate (also used for delta Z axis)
-  #define NOZZLE_PARK_Z_FEEDRATE    5   // (mm/s) Z axis feedrate (not used for delta printers)
+  #define NOZZLE_PARK_Z_FEEDRATE 5      // (mm/s) Z axis feedrate (not used for delta printers)
 #endif
 
 /**
@@ -1733,7 +1933,7 @@
  *
  * View the current statistics with M78.
  */
-//#define PRINTCOUNTER
+#define PRINTCOUNTER
 
 /**
  * Password
@@ -1821,7 +2021,17 @@
  * SD Card support is disabled by default. If your controller has an SD slot,
  * you must uncomment the following option or it won't work.
  */
-//#define SDSUPPORT
+#define SDSUPPORT
+
+/**
+ * SD CARD: SPI SPEED
+ *
+ * Enable one of the following items for a slower SPI transfer speed.
+ * This may be required to resolve "volume init" errors.
+ */
+//#define SPI_SPEED SPI_HALF_SPEED
+#define SPI_SPEED SPI_QUARTER_SPEED
+//#define SPI_SPEED SPI_EIGHTH_SPEED
 
 /**
  * SD CARD: ENABLE CRC
@@ -1891,7 +2101,7 @@
 //
 // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
 //
-//#define INDIVIDUAL_AXIS_HOMING_MENU
+#define INDIVIDUAL_AXIS_HOMING_MENU
 
 //
 // SPEAKER/BUZZER
@@ -1922,7 +2132,9 @@
 //
 // Note: Usually sold with a white PCB.
 //
-//#define REPRAP_DISCOUNT_SMART_CONTROLLER
+#if DISABLED(GRAPHICSLCD)
+  #define REPRAP_DISCOUNT_SMART_CONTROLLER
+#endif
 
 //
 // Original RADDS LCD Display+Encoder+SDCardReader
@@ -2072,7 +2284,9 @@
 // RepRapDiscount FULL GRAPHIC Smart Controller
 // https://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
 //
-//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
+#if ENABLED(GRAPHICSLCD)
+  #define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
+#endif
 
 //
 // ReprapWorld Graphical LCD
@@ -2255,7 +2469,7 @@
 //#define DGUS_LCD_UI_HIPRECY
 
 //
-// Touch-screen LCD for Malyan M200/M300 printers
+// Touch-screen LCD for Malyan M200 printers
 //
 //#define MALYAN_LCD
 #if ENABLED(MALYAN_LCD)

Marlin/Configuration_adv.h

@@ -186,12 +186,12 @@
  * THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
  */
 #if ENABLED(THERMAL_PROTECTION_HOTENDS)
-  #define THERMAL_PROTECTION_PERIOD 40        // Seconds
-  #define THERMAL_PROTECTION_HYSTERESIS 4     // Degrees Celsius
+  #define THERMAL_PROTECTION_PERIOD 120        // Seconds
+  #define THERMAL_PROTECTION_HYSTERESIS 10     // Degrees Celsius
 
-  //#define ADAPTIVE_FAN_SLOWING              // Slow part cooling fan if temperature drops
+  #define ADAPTIVE_FAN_SLOWING              // Slow part cooling fan if temperature drops
   #if BOTH(ADAPTIVE_FAN_SLOWING, PIDTEMP)
-    //#define NO_FAN_SLOWING_IN_PID_TUNING    // Don't slow fan speed during M303
+    #define NO_FAN_SLOWING_IN_PID_TUNING    // Don't slow fan speed during M303
   #endif
 
   /**
@@ -206,36 +206,36 @@
    * and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set
    * below 2.
    */
-  #define WATCH_TEMP_PERIOD 20                // Seconds
-  #define WATCH_TEMP_INCREASE 2               // Degrees Celsius
+  #define WATCH_TEMP_PERIOD 120                // Seconds
+  #define WATCH_TEMP_INCREASE 4               // Degrees Celsius
 #endif
 
 /**
  * Thermal Protection parameters for the bed are just as above for hotends.
  */
 #if ENABLED(THERMAL_PROTECTION_BED)
-  #define THERMAL_PROTECTION_BED_PERIOD        20 // Seconds
-  #define THERMAL_PROTECTION_BED_HYSTERESIS     2 // Degrees Celsius
+  #define THERMAL_PROTECTION_BED_PERIOD 240    // Seconds
+  #define THERMAL_PROTECTION_BED_HYSTERESIS 4 // Degrees Celsius
 
   /**
    * As described above, except for the bed (M140/M190/M303).
    */
-  #define WATCH_BED_TEMP_PERIOD                60 // Seconds
-  #define WATCH_BED_TEMP_INCREASE               2 // Degrees Celsius
+  #define WATCH_BED_TEMP_PERIOD 240                // Seconds
+  #define WATCH_BED_TEMP_INCREASE 4               // Degrees Celsius
 #endif
 
 /**
  * Thermal Protection parameters for the heated chamber.
  */
 #if ENABLED(THERMAL_PROTECTION_CHAMBER)
-  #define THERMAL_PROTECTION_CHAMBER_PERIOD    20 // Seconds
+  #define THERMAL_PROTECTION_CHAMBER_PERIOD 20    // Seconds
   #define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
 
   /**
    * Heated chamber watch settings (M141/M191).
    */
-  #define WATCH_CHAMBER_TEMP_PERIOD            60 // Seconds
-  #define WATCH_CHAMBER_TEMP_INCREASE           2 // Degrees Celsius
+  #define WATCH_CHAMBER_TEMP_PERIOD 60            // Seconds
+  #define WATCH_CHAMBER_TEMP_INCREASE 2           // Degrees Celsius
 #endif
 
 #if ENABLED(PIDTEMP)
@@ -573,8 +573,11 @@
 //
 // For Z set the number of stepper drivers
 //
-#define NUM_Z_STEPPER_DRIVERS 1   // (1-4) Z options change based on how many
-
+#if ENABLED(DUAL_Z)
+  #define NUM_Z_STEPPER_DRIVERS 2   // (1-4) Z options change based on how many
+#else
+  #define NUM_Z_STEPPER_DRIVERS 1   // (1-4) Z options change based on how many
+#endif
 #if NUM_Z_STEPPER_DRIVERS > 1
   //#define Z_MULTI_ENDSTOPS
   #if ENABLED(Z_MULTI_ENDSTOPS)
@@ -659,9 +662,9 @@
 #define HOMING_BUMP_MM      { 5, 5, 2 }       // (mm) Backoff from endstops after first bump
 #define HOMING_BUMP_DIVISOR { 2, 2, 4 }       // Re-Bump Speed Divisor (Divides the Homing Feedrate)
 
-//#define HOMING_BACKOFF_POST_MM { 2, 2, 2 }  // (mm) Backoff from endstops after homing
+#define HOMING_BACKOFF_POST_MM { 2, 2, 2 }  // (mm) Backoff from endstops after homing
 
-//#define QUICK_HOME                          // If G28 contains XY do a diagonal move first
+#define QUICK_HOME                          // If G28 contains XY do a diagonal move first
 //#define HOME_Y_BEFORE_X                     // If G28 contains XY home Y before X
 //#define HOME_Z_FIRST                        // Home Z first. Requires a Z-MIN endstop (not a probe).
 //#define CODEPENDENT_XY_HOMING               // If X/Y can't home without homing Y/X first
@@ -728,7 +731,7 @@
    * This feature was designed for Delta's with very fast Z moves however higher speed cartesians may function
    * If the machine cannot raise the probe fast enough after a trigger, it may enter a fault state.
    */
-  //#define BLTOUCH_HS_MODE
+  #define BLTOUCH_HS_MODE
 
   // Safety: Enable voltage mode settings in the LCD menu.
   //#define BLTOUCH_LCD_VOLTAGE_MENU
@@ -741,7 +744,9 @@
  * Z Steppers Auto-Alignment
  * Add the G34 command to align multiple Z steppers using a bed probe.
  */
-//#define Z_STEPPER_AUTO_ALIGN
+#if ENABLED(DUAL_Z)
+  #define Z_STEPPER_AUTO_ALIGN
+#endif
 #if ENABLED(Z_STEPPER_AUTO_ALIGN)
   // Define probe X and Y positions for Z1, Z2 [, Z3 [, Z4]]
   // If not defined, probe limits will be used.
@@ -786,8 +791,8 @@
   #endif
 
   // On a 300mm bed a 5% grade would give a misalignment of ~1.5cm
-  #define G34_MAX_GRADE              5    // (%) Maximum incline that G34 will handle
-  #define Z_STEPPER_ALIGN_ITERATIONS 5    // Number of iterations to apply during alignment
+  #define G34_MAX_GRADE              15    // (%) Maximum incline that G34 will handle
+  #define Z_STEPPER_ALIGN_ITERATIONS 8    // Number of iterations to apply during alignment
   #define Z_STEPPER_ALIGN_ACC        0.02 // Stop iterating early if the accuracy is better than this
   #define RESTORE_LEVELING_AFTER_G34      // Restore leveling after G34 is done?
   // After G34, re-home Z (G28 Z) or just calculate it from the last probe heights?
@@ -888,6 +893,7 @@
 // Backlash Compensation
 // Adds extra movement to axes on direction-changes to account for backlash.
 //
+
 //#define BACKLASH_COMPENSATION
 #if ENABLED(BACKLASH_COMPENSATION)
   // Define values for backlash distance and correction.
@@ -979,8 +985,9 @@
  * vibration and surface artifacts. The algorithm adapts to provide the best possible step smoothing at the
  * lowest stepping frequencies.
  */
-//#define ADAPTIVE_STEP_SMOOTHING
-
+#if ENABLED(SKRLPCBoard)
+  #define ADAPTIVE_STEP_SMOOTHING
+#endif
 /**
  * Custom Microstepping
  * Override as-needed for your setup. Up to 3 MS pins are supported.
@@ -1095,7 +1102,7 @@
   #endif
 
   // Include a page of printer information in the LCD Main Menu
-  //#define LCD_INFO_MENU
+  #define LCD_INFO_MENU
   #if ENABLED(LCD_INFO_MENU)
     //#define LCD_PRINTER_INFO_IS_BOOTSCREEN // Show bootscreen(s) instead of Printer Info pages
   #endif
@@ -1139,20 +1146,20 @@
   //#define LCD_TIMEOUT_TO_STATUS 15000
 
   #if ENABLED(SHOW_BOOTSCREEN)
-    #define BOOTSCREEN_TIMEOUT 4000      // (ms) Total Duration to display the boot screen(s)
+    #define BOOTSCREEN_TIMEOUT 2000      // (ms) Total Duration to display the boot screen(s)
     #if EITHER(HAS_MARLINUI_U8GLIB, TFT_COLOR_UI)
       #define BOOT_MARLIN_LOGO_SMALL     // Show a smaller Marlin logo on the Boot Screen (saving lots of flash)
     #endif
   #endif
 
   // Scroll a longer status message into view
-  //#define STATUS_MESSAGE_SCROLLING
+  #define STATUS_MESSAGE_SCROLLING
 
   // On the Info Screen, display XY with one decimal place when possible
   //#define LCD_DECIMAL_SMALL_XY
 
   // Add an 'M73' G-code to set the current percentage
-  //#define LCD_SET_PROGRESS_MANUALLY
+  #define LCD_SET_PROGRESS_MANUALLY
 
   // Show the E position (filament used) during printing
   //#define LCD_SHOW_E_TOTAL
@@ -1195,7 +1202,7 @@
 
   // The standard SD detect circuit reads LOW when media is inserted and HIGH when empty.
   // Enable this option and set to HIGH if your SD cards are incorrectly detected.
-  //#define SD_DETECT_STATE HIGH
+  #define SD_DETECT_STATE HIGH
 
   //#define SD_IGNORE_AT_STARTUP            // Don't mount the SD card when starting up
   //#define SDCARD_READONLY                 // Read-only SD card (to save over 2K of flash)
@@ -1232,7 +1239,9 @@
    * an option on the LCD screen to continue the print from the last-known
    * point in the file.
    */
-  //#define POWER_LOSS_RECOVERY
+  #if ENABLED(SKRLPCBoard)
+    #define POWER_LOSS_RECOVERY
+  #endif
   #if ENABLED(POWER_LOSS_RECOVERY)
     #define PLR_ENABLED_DEFAULT   false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
     //#define BACKUP_POWER_SUPPLY       // Backup power / UPS to move the steppers on power loss
@@ -1293,10 +1302,10 @@
   //#define UTF_FILENAME_SUPPORT
 
   // This allows hosts to request long names for files and folders with M33
-  //#define LONG_FILENAME_HOST_SUPPORT
+  #define LONG_FILENAME_HOST_SUPPORT
 
   // Enable this option to scroll long filenames in the SD card menu
-  //#define SCROLL_LONG_FILENAMES
+  #define SCROLL_LONG_FILENAMES
 
   // Leave the heaters on after Stop Print (not recommended!)
   //#define SD_ABORT_NO_COOLDOWN
@@ -1318,7 +1327,7 @@
   /**
    * Auto-report SdCard status with M27 S<seconds>
    */
-  //#define AUTO_REPORT_SD_STATUS
+  #define AUTO_REPORT_SD_STATUS
 
   /**
    * Support for USB thumb drives using an Arduino USB Host Shield or
@@ -1412,7 +1421,7 @@
  */
 #if HAS_MARLINUI_U8GLIB
   // Show SD percentage next to the progress bar
-  //#define DOGM_SD_PERCENT
+  #define DOGM_SD_PERCENT
 
   // Save many cycles by drawing a hollow frame or no frame on the Info Screen
   //#define XYZ_NO_FRAME
@@ -1423,7 +1432,7 @@
 
   // A bigger font is available for edit items. Costs 3120 bytes of PROGMEM.
   // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
-  //#define USE_BIG_EDIT_FONT
+  #define USE_BIG_EDIT_FONT
 
   // A smaller font may be used on the Info Screen. Costs 2434 bytes of PROGMEM.
   // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
@@ -1471,13 +1480,18 @@
   //#define STATUS_ALT_FAN_BITMAP     // Use the alternative fan bitmap
   //#define STATUS_FAN_FRAMES 3       // :[0,1,2,3,4] Number of fan animation frames
   //#define STATUS_HEAT_PERCENT       // Show heating in a progress bar
-  //#define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~‭3260 (or ~940) bytes of PROGMEM.
+  #if DISABLED(SKRLPCBoard)
+    #define BOOT_MARLIN_LOGO_SMALL    // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash)
+  #else
+    #define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~‭3260 (or ~940) bytes of PROGMEM.
+  #endif
 
   // Frivolous Game Options
-  //#define MARLIN_BRICKOUT
-  //#define MARLIN_INVADERS
-  //#define MARLIN_SNAKE
-  //#define GAMES_EASTER_EGG          // Add extra blank lines above the "Games" sub-menu
+  #if ENABLED(SKRLPCBoard)
+    #define MARLIN_BRICKOUT
+    #define MARLIN_INVADERS
+    #define MARLIN_SNAKE
+  #endif
 
 #endif // HAS_MARLINUI_U8GLIB
 
@@ -1655,18 +1669,18 @@
  *
  * Warning: Does not respect endstops!
  */
-//#define BABYSTEPPING
+#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
-  //#define INTEGRATED_BABYSTEPPING         // EXPERIMENTAL integration of babystepping into the Stepper ISR
+  #define INTEGRATED_BABYSTEPPING         // EXPERIMENTAL integration of babystepping into the Stepper ISR
   //#define BABYSTEP_WITHOUT_HOMING
-  //#define BABYSTEP_ALWAYS_AVAILABLE       // Allow babystepping at all times (not just during movement).
+  #define BABYSTEP_ALWAYS_AVAILABLE       // Allow babystepping at all times (not just during movement).
   //#define BABYSTEP_XY                     // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false           // Change if Z babysteps should go the other way
   //#define BABYSTEP_MILLIMETER_UNITS       // Specify BABYSTEP_MULTIPLICATOR_(XY|Z) in mm instead of micro-steps
-  #define BABYSTEP_MULTIPLICATOR_Z  1       // (steps or mm) Steps or millimeter distance for each Z babystep
+  #define BABYSTEP_MULTIPLICATOR_Z  10       // (steps or mm) Steps or millimeter distance for each Z babystep
   #define BABYSTEP_MULTIPLICATOR_XY 1       // (steps or mm) Steps or millimeter distance for each XY babystep
 
-  //#define DOUBLECLICK_FOR_Z_BABYSTEPPING  // Double-click on the Status Screen for Z Babystepping.
+  #define DOUBLECLICK_FOR_Z_BABYSTEPPING  // Double-click on the Status Screen for Z Babystepping.
   #if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING)
     #define DOUBLECLICK_MAX_INTERVAL 1250   // Maximum interval between clicks, in milliseconds.
                                             // Note: Extra time may be added to mitigate controller latency.
@@ -1678,10 +1692,12 @@
 
   //#define BABYSTEP_DISPLAY_TOTAL          // Display total babysteps since last G28
 
-  //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
+  #define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets
-    //#define BABYSTEP_ZPROBE_GFX_OVERLAY   // Enable graphical overlay on Z-offset editor
+    #if ENABLED(GRAPHICSLCD)
+      #define BABYSTEP_ZPROBE_GFX_OVERLAY   // Enable graphical overlay on Z-offset editor
+    #endif
   #endif
 #endif
 
@@ -1702,10 +1718,12 @@
  *
  * See https://marlinfw.org/docs/features/lin_advance.html for full instructions.
  */
-//#define LIN_ADVANCE
+#if E0_DRIVER_TYPE != TMC2208_STANDALONE
+  #define LIN_ADVANCE
+#endif
 #if ENABLED(LIN_ADVANCE)
   //#define EXTRA_LIN_ADVANCE_K // Enable for second linear advance constants
-  #define LIN_ADVANCE_K 0.22    // Unit: mm compression per 1mm/s extruder speed
+  #define LIN_ADVANCE_K 0.0    // Unit: mm compression per 1mm/s extruder speed
   //#define LA_DEBUG            // If enabled, this will generate debug information output over USB.
   //#define EXPERIMENTAL_SCURVE // Enable this option to permit S-Curve Acceleration
 #endif
@@ -1767,7 +1785,9 @@
  * Repeatedly attempt G29 leveling until it succeeds.
  * Stop after G29_MAX_RETRIES attempts.
  */
-//#define G29_RETRY_AND_RECOVER
+#if DISABLED(UBL)
+  #define G29_RETRY_AND_RECOVER
+#endif
 #if ENABLED(G29_RETRY_AND_RECOVER)
   #define G29_MAX_RETRIES 3
   #define G29_HALT_ON_FAILURE
@@ -1776,7 +1796,7 @@
    * between attempts, and after the maximum number of retries have been tried.
    */
   #define G29_SUCCESS_COMMANDS "M117 Bed leveling done."
-  #define G29_RECOVER_COMMANDS "M117 Probe failed. Rewiping.\nG28\nG12 P0 S12 T0"
+  #define G29_RECOVER_COMMANDS "M117 Probe failed.\nG28\n"
   #define G29_FAILURE_COMMANDS "M117 Bed leveling failed.\nG0 Z10\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nM300 P25 S880\nM300 P50 S0\nG4 S1"
 
 #endif
@@ -1860,7 +1880,7 @@
 #endif
 
 // Support for G5 with XYZE destination and IJPQ offsets. Requires ~2666 bytes.
-//#define BEZIER_CURVE_SUPPORT
+#define BEZIER_CURVE_SUPPORT
 
 /**
  * Direct Stepping
@@ -1934,8 +1954,9 @@
 // @section temperature
 
 // Control heater 0 and heater 1 in parallel.
-//#define HEATERS_PARALLEL
-
+#if ENABLED(SliceDualHeater)
+  #define HEATERS_PARALLEL
+#endif
 //===========================================================================
 //================================= Buffers =================================
 //===========================================================================
@@ -1956,7 +1977,13 @@
 
 // The ASCII buffer for serial input
 #define MAX_CMD_SIZE 96
-#define BUFSIZE 4
+#if ENABLED(SKRLPCBoard)
+  #define BUFSIZE 32
+#elif BOTH(GRAPHICSLCD, UBL)
+  #define BUFSIZE 12
+#else
+  #define BUFSIZE 16
+#endif
 
 // Transmission to Host Buffer Size
 // To save 386 bytes of PROGMEM (and TX_BUFFER_SIZE+3 bytes of RAM) set to 0.
@@ -2000,16 +2027,16 @@
  * Currently handles M108, M112, M410, M876
  * NOTE: Not yet implemented for all platforms.
  */
-//#define EMERGENCY_PARSER
+#define EMERGENCY_PARSER
 
 // Bad Serial-connections can miss a received command by sending an 'ok'
 // Therefore some clients abort after 30 seconds in a timeout.
 // Some other clients start sending commands while receiving a 'wait'.
 // This "wait" is only sent when the buffer is empty. 1 second is a good value here.
-//#define NO_TIMEOUTS 1000 // Milliseconds
+#define NO_TIMEOUTS 1000 // Milliseconds
 
 // Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary.
-//#define ADVANCED_OK
+#define ADVANCED_OK
 
 // Printrun may have trouble receiving long strings all at once.
 // This option inserts short delays between lines of serial output.
@@ -2043,7 +2070,7 @@
  *
  * Note that M207 / M208 / M209 settings are saved to EEPROM.
  */
-//#define FWRETRACT
+#define FWRETRACT
 #if ENABLED(FWRETRACT)
   #define FWRETRACT_AUTORETRACT           // Override slicer retractions
   #if ENABLED(FWRETRACT_AUTORETRACT)
@@ -2143,7 +2170,7 @@
  * Requires NOZZLE_PARK_FEATURE.
  * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
  */
-//#define ADVANCED_PAUSE_FEATURE
+#define ADVANCED_PAUSE_FEATURE
 #if ENABLED(ADVANCED_PAUSE_FEATURE)
   #define PAUSE_PARK_RETRACT_FEEDRATE         60  // (mm/s) Initial retract feedrate.
   #define PAUSE_PARK_RETRACT_LENGTH            2  // (mm) Initial retract.
@@ -2169,7 +2196,7 @@
                                                   //   Filament can be extruded repeatedly from the Filament Change menu
                                                   //   until extrusion is consistent, and to purge old filament.
   #define ADVANCED_PAUSE_RESUME_PRIME          0  // (mm) Extra distance to prime nozzle after returning from park.
-  //#define ADVANCED_PAUSE_FANS_PAUSE             // Turn off print-cooling fans while the machine is paused.
+  #define ADVANCED_PAUSE_FANS_PAUSE             // Turn off print-cooling fans while the machine is paused.
 
                                                   // Filament Unload does a Retract, Delay, and Purge first:
   #define FILAMENT_UNLOAD_PURGE_RETRACT       13  // (mm) Unload initial retract length.
@@ -2178,14 +2205,14 @@
   #define FILAMENT_UNLOAD_PURGE_FEEDRATE      25  // (mm/s) feedrate to purge before unload
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT           45  // (seconds) Time limit before the nozzle is turned off for safety.
-  #define FILAMENT_CHANGE_ALERT_BEEPS         10  // Number of alert beeps to play when a response is needed.
+  #define FILAMENT_CHANGE_ALERT_BEEPS         2  // Number of alert beeps to play when a response is needed.
   #define PAUSE_PARK_NO_STEPPER_TIMEOUT           // Enable for XYZ steppers to stay powered on during filament change.
 
-  //#define PARK_HEAD_ON_PAUSE                    // Park the nozzle during pause and filament change.
-  //#define HOME_BEFORE_FILAMENT_CHANGE           // If needed, home before parking for filament change
+  #define PARK_HEAD_ON_PAUSE                    // Park the nozzle during pause and filament change.
+  #define HOME_BEFORE_FILAMENT_CHANGE           // Ensure homing has been completed prior to parking for filament change
 
-  //#define FILAMENT_LOAD_UNLOAD_GCODES           // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
-  //#define FILAMENT_UNLOAD_ALL_EXTRUDERS         // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
+  #define FILAMENT_LOAD_UNLOAD_GCODES           // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
+  #define FILAMENT_UNLOAD_ALL_EXTRUDERS         // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
 #endif
 
 // @section tmc
@@ -2551,7 +2578,7 @@
    * Define your own with:
    * { <off_time[1..15]>, <hysteresis_end[-3..12]>, hysteresis_start[1..8] }
    */
-  #define CHOPPER_TIMING CHOPPER_DEFAULT_12V        // All axes (override below)
+  #define CHOPPER_TIMING CHOPPER_DEFAULT_24V        // All axes (override below)
   //#define CHOPPER_TIMING_X  CHOPPER_DEFAULT_12V   // For X Axes (override below)
   //#define CHOPPER_TIMING_X2 CHOPPER_DEFAULT_12V
   //#define CHOPPER_TIMING_Y  CHOPPER_DEFAULT_12V   // For Y Axes (override below)
@@ -2595,7 +2622,7 @@
    * STEALTHCHOP_(XY|Z|E) must be enabled to use HYBRID_THRESHOLD.
    * M913 X/Y/Z/E to live tune the setting
    */
-  //#define HYBRID_THRESHOLD
+  #define HYBRID_THRESHOLD
 
   #define X_HYBRID_THRESHOLD     100  // [mm/s]
   #define X2_HYBRID_THRESHOLD    100
@@ -3324,27 +3351,37 @@
 /**
  * User-defined menu items that execute custom GCode
  */
-//#define CUSTOM_USER_MENUS
+#define CUSTOM_USER_MENUS
 #if ENABLED(CUSTOM_USER_MENUS)
-  //#define CUSTOM_USER_MENU_TITLE "Custom Commands"
-  #define USER_SCRIPT_DONE "M117 User Script Done"
+  //#define USER_SCRIPT_DONE "M117 User Script Done"
   #define USER_SCRIPT_AUDIBLE_FEEDBACK
-  //#define USER_SCRIPT_RETURN  // Return to status screen after a script
+  #define USER_SCRIPT_RETURN  // Return to status screen after a script
+  #define CUSTOM_USER_MENU_TITLE "Leveling Tools"
 
-  #define USER_DESC_1 "Home & UBL Info"
-  #define USER_GCODE_1 "G28\nG29 W"
+  #define CommBedTmp "65"
+  #if ENABLED(DUAL_Z)
+    #define ALIGN_CMD "G34RI20\n"
+  #else
+    #define ALIGN_CMD ""
+  #endif
+  #define USER_DESC_1 "Setup"
+  #if (ENABLED(UBL))
+    #define USER_GCODE_1 "M190S" CommBedTmp"\nG28\n" ALIGN_CMD "G29P1\nG29S1\nG29S0\n G29F0.0\nG29A\nG28\nM109S225\nG1X150Y150\nG1Z0\nM500\nM400\nM77\nM117 Set Z Offset"
+  #else
+    #define USER_GCODE_1 "M190S" CommBedTmp"\n M117 Probing....\nM104S225\nG28\n" ALIGN_CMD "G29\nM400\nG28\nM420S1\nM109S225\nG1X100Y100\nG1Z0\nM500\nM400\nM77\nM117 Set Z Offset"
+  #endif
 
-  #define USER_DESC_2 "Preheat for " PREHEAT_1_LABEL
-  #define USER_GCODE_2 "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND)
+  #define USER_DESC_2 "PID Tune"
+  #define USER_GCODE_2 "M106 S128\nM303C8S225E0\nM500\nM117 PID Tune Done"
 
-  #define USER_DESC_3 "Preheat for " PREHEAT_2_LABEL
-  #define USER_GCODE_3 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND)
+  #define USER_DESC_3 "Prep for Z Adjust"
+  #define USER_GCODE_3 "M190S" CommBedTmp"\nM104S235\nG28\nG29L1\nG1X100Y100\nG1Z0"
 
-  #define USER_DESC_4 "Heat Bed/Home/Level"
-  #define USER_GCODE_4 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29"
+  #define USER_DESC_4 "Store Settings"
+  #define USER_GCODE_4 "M500\nM117 Settings Stored"
 
-  #define USER_DESC_5 "Home & Info"
-  #define USER_GCODE_5 "G28\nM503"
+  //#define USER_DESC_5 "Run Mesh Validation"
+  //#define USER_GCODE_5 "G26"
 #endif
 
 /**
@@ -3361,10 +3398,10 @@
  * Host Prompt Support enables Marlin to use the host for user prompts so
  * filament runout and other processes can be managed from the host side.
  */
-//#define HOST_ACTION_COMMANDS
+#define HOST_ACTION_COMMANDS
 #if ENABLED(HOST_ACTION_COMMANDS)
-  //#define HOST_PROMPT_SUPPORT
-  //#define HOST_START_MENU_ITEM  // Add a menu item that tells the host to start
+  #define HOST_PROMPT_SUPPORT
+  #define HOST_START_MENU_ITEM  // Add a menu item that tells the host to start
 #endif
 
 /**
@@ -3372,7 +3409,7 @@
  *
  * Implement M486 to allow Marlin to skip objects
  */
-//#define CANCEL_OBJECTS
+#define CANCEL_OBJECTS
 
 /**
  * I2C position encoders for closed loop control.

Marlin/Version.h

@@ -1,6 +1,6 @@
 /**
  * Marlin 3D Printer Firmware
- * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ * Copyright (c) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  *
  * Based on Sprinter and grbl.
  * Copyright (c) 2011 Camiel Gubbels / Erik van der Zalm
@@ -28,25 +28,25 @@
 /**
  * Marlin release version identifier
  */
-//#define SHORT_BUILD_VERSION "bugfix-2.0.x"
+#define SHORT_BUILD_VERSION "2.0.7_SX1"
 
 /**
  * Verbose version identifier which should contain a reference to the location
  * from where the binary was downloaded or the source code was compiled.
  */
-//#define DETAILED_BUILD_VERSION SHORT_BUILD_VERSION
+#define DETAILED_BUILD_VERSION SHORT_BUILD_VERSION " TM3D"
 
 /**
  * The STRING_DISTRIBUTION_DATE represents when the binary file was built,
  * here we define this default string as the date where the latest release
  * version was tagged.
  */
-//#define STRING_DISTRIBUTION_DATE "2019-07-10"
+#define STRING_DISTRIBUTION_DATE "2021-01-03"
 
 /**
  * Defines a generic printer name to be output to the LCD after booting Marlin.
  */
-//#define MACHINE_NAME "3D Printer"
+#define MACHINE_NAME "TM3D SX4"
 
 /**
  * The SOURCE_CODE_URL is the location where users will find the Marlin Source
@@ -54,7 +54,7 @@
  * has a distinct Github fork— the Source Code URL should just be the main
  * Marlin repository.
  */
-//#define SOURCE_CODE_URL "github.com/MarlinFirmware/Marlin"
+#define SOURCE_CODE_URL "https://github.com/InsanityAutomation/Marlin/tree/TM_SX4_2.0"
 
 /**
  * Default generic printer UUID.
@@ -65,7 +65,7 @@
  * The WEBSITE_URL is the location where users can get more information such as
  * documentation about a specific Marlin release.
  */
-//#define WEBSITE_URL "marlinfw.org"
+#define WEBSITE_URL "tinymachines3d.com"
 
 /**
  * Set the vendor info the serial USB interface, if changable

Marlin/_Bootscreen.h

@@ -0,0 +1,93 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Custom Bitmap for splashscreen
+ *
+ * You may use one of the following tools to generate the C++ bitmap array from
+ * a black and white image:
+ *
+ *  - http://www.marlinfw.org/tools/u8glib/converter.html
+ *  - http://www.digole.com/tools/PicturetoC_Hex_converter.php
+ */
+
+#define CUSTOM_BOOTSCREEN_TIMEOUT   2500
+#define CUSTOM_BOOTSCREEN_BMPWIDTH  128
+#define CUSTOM_BOOTSCREEN_INVERTED
+
+const unsigned char custom_start_bmp[] PROGMEM = {
+  B11111101,B01010101,B01010101,B01010101,B01010101,B01010101,B01011111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,
+  B11111110,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,
+  B11111101,B00000000,B00000000,B00000111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,
+  B11111110,B00000111,B11000000,B00000101,B01010101,B01010101,B01010101,B01010101,B01010101,B01011111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,
+  B11111100,B00001010,B00100000,B00000110,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,
+  B11111110,B00010100,B00010000,B00000101,B00000000,B00000000,B00000111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,
+  B11111100,B00101000,B00001000,B00000110,B00000111,B11000000,B00000101,B01010101,B01010101,B01010101,B01010101,B01010101,B01011111,B11111111,B11111111,B11111111,
+  B11111110,B01010100,B00000100,B00000100,B00001010,B00100000,B00000110,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11111111,B11111111,B11111111,
+  B11111100,B01100000,B00000100,B00000110,B00010100,B00010000,B00000101,B00000000,B00000000,B00000111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,
+  B11111110,B01010000,B00000100,B00000100,B00101000,B00001000,B00000110,B00000111,B11000000,B00000101,B01010101,B01010101,B01010101,B01010101,B01010101,B01011111,
+  B11111100,B01100000,B00000100,B00000110,B01010100,B00000100,B00000100,B00001010,B00100000,B00000110,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,
+  B11111110,B01010100,B00000100,B00011100,B01100000,B00000100,B00000110,B00010100,B00010000,B00000101,B00000000,B00000000,B00000000,B00000000,B00000000,B00011111,
+  B11111100,B00101000,B00001000,B00101110,B01010000,B00000100,B00000100,B00101000,B00001000,B00000110,B00000111,B11000000,B00000000,B00000001,B11110000,B00111111,
+  B11111110,B00010100,B00010000,B01010100,B01100000,B00000100,B00000110,B01010100,B00000100,B00000100,B00001010,B00100000,B00000000,B00000010,B00001000,B00011111,
+  B11111100,B00001010,B00100000,B01100110,B01010100,B00000100,B00011100,B01100000,B00000100,B00000110,B00010100,B00010000,B00000000,B00000101,B00000100,B00111111,
+  B11111110,B00000111,B11000000,B01010100,B00101000,B00001000,B00101110,B01010000,B00000100,B00000100,B00101000,B00001000,B00000000,B00001010,B00000010,B00011111,
+  B11111100,B00000000,B00000000,B00101110,B00010100,B00010000,B01010100,B01100000,B00000100,B00000110,B01010100,B00000100,B00000000,B00010101,B00000001,B00111111,
+  B11111110,B00000000,B00000000,B00011100,B00001010,B00100000,B01100110,B01010100,B00000100,B00011100,B01100000,B00000100,B00000000,B00011000,B00000001,B00011111,
+  B11111100,B00000000,B00000000,B00000110,B00000111,B11000000,B01010100,B00101000,B00001000,B00101110,B01010000,B00000100,B00000000,B00010100,B00000001,B00111111,
+  B11111110,B00000000,B00000000,B00000100,B00000000,B00000000,B00101110,B00010100,B00010000,B01010100,B01100000,B00000100,B00000000,B00011000,B00000001,B00011111,
+  B11111100,B11111111,B11111111,B11111110,B00000000,B00000000,B00011100,B00001010,B00100000,B01100110,B01010100,B00000100,B00011100,B00010101,B00000001,B00111111,
+  B11111110,B11010101,B01010101,B01010100,B00000000,B00000000,B00000110,B00000111,B11000000,B01010100,B00101000,B00001000,B00101010,B00001010,B00000010,B00011111,
+  B11111100,B10000100,B00010000,B01000110,B00000000,B00000000,B00000100,B00000000,B00000000,B00101110,B00010100,B00010000,B01010001,B00000101,B00000100,B00111111,
+  B11111110,B11000100,B00010000,B01000100,B11111111,B11111111,B11111110,B00000000,B00000000,B00011100,B00001010,B00100000,B01100001,B00000010,B10001000,B00011111,
+  B11111100,B10000100,B00010000,B01000110,B11010101,B01010101,B01010100,B00000000,B00000000,B00000110,B00000111,B11000000,B01010001,B00000001,B11110000,B00111111,
+  B11111110,B10000100,B00010000,B01000100,B10000100,B00010000,B01000110,B00000000,B00000000,B00000100,B00000000,B00000000,B00101010,B00000000,B00000000,B00011111,
+  B11111100,B11000100,B00010000,B01000110,B11000100,B00010000,B01000100,B11111111,B11111111,B11111110,B00000000,B00000000,B00011100,B00000000,B00000000,B00111111,
+  B11111110,B10000100,B00010000,B01000100,B10000100,B00010000,B01000110,B11010101,B01010101,B01010100,B00000000,B00000000,B00000000,B00000000,B00000000,B00011111,
+  B11111100,B11010101,B01010101,B01010110,B10000100,B00010000,B01000100,B10000100,B00010000,B01000110,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,
+  B11111100,B11111111,B11111111,B11111100,B11000100,B00010000,B01000110,B11000100,B00010000,B01000100,B11111111,B11111111,B11111111,B11111111,B11111111,B10011111,
+  B11111110,B00000000,B00000000,B00000110,B10000100,B00010000,B01000100,B10000100,B00010000,B01000110,B11010101,B01010101,B01010101,B01010101,B01010101,B10111111,
+  B11111101,B01010101,B01010101,B01010100,B11010101,B01010101,B01010110,B10000100,B00010000,B01000100,B10000100,B00010000,B01000001,B00000100,B00010000,B10011111,
+  B11111111,B11111111,B11111111,B11111100,B11111111,B11111111,B11111100,B11000100,B00010000,B01000110,B11000100,B00010000,B01000001,B00000100,B00010001,B10111111,
+  B11111111,B11111111,B11111111,B11111110,B00000000,B00000000,B00000110,B10000100,B00010000,B01000100,B10000100,B00010000,B01000001,B00000100,B00010000,B10011111,
+  B11111111,B11111111,B11111111,B11111101,B01010101,B01010101,B01010100,B11010101,B01010101,B01010110,B10000100,B00010000,B01000001,B00000100,B00010000,B10011111,
+  B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111100,B11111111,B11111111,B11111100,B11000100,B00010000,B01000001,B00000100,B00010001,B10111111,
+  B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111110,B00000000,B00000000,B00000110,B10000100,B00010000,B01000001,B00000100,B00010000,B10011111,
+  B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111101,B01010101,B01010101,B01010100,B11010101,B01010101,B01010101,B01010101,B01010101,B10111111,
+  B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111100,B11111111,B11111111,B11111111,B11111111,B11111111,B10011111,
+  B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111110,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,
+  B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111101,B01010101,B01010101,B01010101,B01010101,B01010101,B01011111,
+  B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,
+  B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,
+  B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,
+  B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,B11111111,
+  B11100000,B00101110,B11111011,B01111101,B11111011,B11111011,B11001111,B11000001,B11011111,B10111011,B00111110,B11000000,B11100001,B11111110,B00111100,B00011111,
+  B11111101,B11101110,B01111011,B00111001,B11111001,B11110011,B11001111,B10011110,B11011111,B10111011,B00111110,B11011111,B11011110,B11111100,B11011101,B11100111,
+  B11111101,B11101110,B00111011,B10111011,B11111001,B11101011,B11010111,B10111111,B01011111,B10111011,B01011110,B11011111,B11011110,B11111101,B11101101,B11110111,
+  B11111101,B11101110,B10111011,B11010011,B11111010,B11101011,B10110111,B00111111,B11011111,B10111011,B01001110,B11011111,B11011111,B11111111,B11001101,B11110011,
+  B11111101,B11101110,B11011011,B11000111,B11111010,B11101011,B10111011,B01111111,B11000000,B00111011,B01101110,B11000000,B11100011,B11111111,B00011101,B11110011,
+  B11111101,B11101110,B11001011,B11101111,B11111010,B11011011,B10111011,B01111111,B11011111,B10111011,B01100110,B11011111,B11111000,B11111111,B11001101,B11110011,
+  B11111101,B11101110,B11101011,B11101111,B11111011,B01011011,B00000011,B00111111,B01011111,B10111011,B01110110,B11011111,B11111110,B01111111,B11101101,B11110011,
+  B11111101,B11101110,B11110011,B11101111,B11111011,B01011011,B01111001,B10111110,B11011111,B10111011,B01111010,B11011111,B11011110,B01111101,B11101101,B11110111,
+  B11111101,B11101110,B11110011,B11101111,B11111011,B10111010,B11111101,B10011110,B11011111,B10111011,B01111100,B11011111,B11011110,B11111101,B11001101,B11100111,
+  B11111101,B11101110,B11111011,B11101111,B11111011,B10111010,B11111101,B11000001,B11011111,B10111011,B01111110,B11000000,B11100000,B11111110,B00011100,B00011111
+};

Marlin/_Statusscreen.h

@@ -0,0 +1,74 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Custom Status Screen bitmap
+ *
+ * Place this file in the root with your configuration files
+ * and enable CUSTOM_STATUS_SCREEN_IMAGE in Configuration.h.
+ *
+ * Use the Marlin Bitmap Converter to make your own:
+ * http://marlinfw.org/tools/u8glib/converter.html
+ */
+
+//
+// Status Screen Logo bitmap
+//
+#define STATUS_LOGO_Y            3
+#define STATUS_LOGO_WIDTH       24
+
+const unsigned char status_logo_bmp[] PROGMEM = {
+  B11111111,B11111111,B11111111,
+  B10000000,B00000000,B00000001,
+  B10001110,B00000000,B11100001,
+  B10011111,B00000001,B11110001,
+  B10010011,B10000001,B00111001,
+  B10011111,B10000001,B11111001,
+  B10011111,B10000001,B11111001,
+  B10011111,B10111001,B11111001,
+  B10001111,B00101000,B11110001,
+  B10000000,B00111000,B00000001,
+  B10000000,B00000000,B00000001,
+  B10011111,B11111111,B11111001,
+  B10010001,B01110100,B10011001,
+  B10011011,B00000110,B10101001,
+  B10011011,B01010100,B10101001,
+  B10011011,B01010110,B10101001,
+  B10011011,B01010100,B10011001,
+  B10011111,B11111111,B11111001,
+  B11111111,B11111111,B11111111
+};
+
+//
+// Use default bitmaps
+//
+#define STATUS_HOTEND_ANIM
+#define STATUS_BED_ANIM
+#if HOTENDS < 2
+  #define STATUS_LOGO_X          8
+  #define STATUS_HEATERS_X      40
+  #define STATUS_BED_X          72
+#else
+  #define STATUS_LOGO_X          0
+  #define STATUS_HEATERS_X      32
+  #define STATUS_BED_X          80
+#endif