Update pins_FORMBOT_TREX2PLUS.h

Co-Authored-By: InsanityAutomation <insanityautomation@users.noreply.github.com>

Marlin/Conditionals_LCD.h

@@ -479,9 +479,11 @@
   #define Z_SERVO_ANGLES { BLTOUCH_DEPLOY, BLTOUCH_STOW }
 
   #define BLTOUCH_DEPLOY    10
-  #define BLTOUCH_ALARM     60
+  #define BLTOUCH_SW_MODE   60
   #define BLTOUCH_STOW      90
   #define BLTOUCH_SELFTEST 120
+  #define BLTOUCH_5V_MODE  140
+  #define BLTOUCH_OD_MODE  150
   #define BLTOUCH_RESET    160
   #define _TEST_BLTOUCH(P) (READ(P##_PIN) != P##_ENDSTOP_INVERTING)
 

Marlin/Configuration_adv.h

@@ -76,7 +76,7 @@
  */
 #if ENABLED(THERMAL_PROTECTION_HOTENDS)
   #define THERMAL_PROTECTION_PERIOD 40        // Seconds
-  #define THERMAL_PROTECTION_HYSTERESIS 4     // Degrees Celsius
+  #define THERMAL_PROTECTION_HYSTERESIS 10     // Degrees Celsius
 
   /**
    * Whenever an M104, M109, or M303 increases the target temperature, the
@@ -98,14 +98,24 @@
  * Thermal Protection parameters for the bed are just as above for hotends.
  */
 #if ENABLED(THERMAL_PROTECTION_BED)
-  #define THERMAL_PROTECTION_BED_PERIOD 20    // Seconds
-  #define THERMAL_PROTECTION_BED_HYSTERESIS 2 // Degrees Celsius
+  #if ENABLED(TREX3) && DISABLED(BedAC)
+    #define THERMAL_PROTECTION_BED_PERIOD 50    // Seconds
+  #else
+    #define THERMAL_PROTECTION_BED_PERIOD 20    // Seconds
+  #endif
+
+  #define THERMAL_PROTECTION_BED_HYSTERESIS 4 // Degrees Celsius
 
   /**
    * As described above, except for the bed (M140/M190/M303).
    */
-  #define WATCH_BED_TEMP_PERIOD 60                // Seconds
-  #define WATCH_BED_TEMP_INCREASE 2               // Degrees Celsius
+  #if ENABLED(TREX3) && DISABLED(BedAC)
+    #define WATCH_BED_TEMP_PERIOD 90                // Seconds
+    #define WATCH_BED_TEMP_INCREASE 2               // Degrees Celsius
+  #else
+    #define WATCH_BED_TEMP_PERIOD 60                // Seconds
+    #define WATCH_BED_TEMP_INCREASE 2               // Degrees Celsius
+  #endif
 #endif
 
 #if ENABLED(PIDTEMP)
@@ -134,7 +144,7 @@
 #endif
 
 // Show extra position information in M114
-//#define M114_DETAIL
+#define M114_DETAIL
 
 // Show Temperature ADC value
 // Enable for M105 to include ADC values read from temperature sensors.
@@ -206,22 +216,12 @@
 // When first starting the main fan, run it at full speed for the
 // given number of milliseconds.  This gets the fan spinning reliably
 // before setting a PWM value. (Does not work with software PWM for fan on Sanguinololu)
-//#define FAN_KICKSTART_TIME 100
+#define FAN_KICKSTART_TIME 100
 
-/**
- * PWM Fan Scaling
- *
- * Define the min/max speeds for PWM fans (as set with M106).
- *
- * With these options the M106 0-255 value range is scaled to a subset
- * to ensure that the fan has enough power to spin, or to run lower
- * current fans with higher current. (e.g., 5V/12V fans with 12V/24V)
- * Value 0 always turns off the fan.
- *
- * Define one or both of these to override the default 0-255 range.
- */
+// This defines the minimal speed for the main fan, run in PWM mode
+// to enable uncomment and set minimal PWM speed for reliable running (1-255)
+// if fan speed is [1 - (FAN_MIN_PWM-1)] it is set to FAN_MIN_PWM
 //#define FAN_MIN_PWM 50
-//#define FAN_MAX_PWM 128
 
 // @section extruder
 
@@ -237,12 +237,16 @@
  * Multiple extruders can be assigned to the same pin in which case
  * the fan will turn on when any selected extruder is above the threshold.
  */
-#define E0_AUTO_FAN_PIN -1
-#define E1_AUTO_FAN_PIN -1
+#if ENABLED(TREX3)
+  #define E0_AUTO_FAN_PIN  6
+  #define E1_AUTO_FAN_PIN  45
+#else
+  #define E0_AUTO_FAN_PIN -1
+  #define E1_AUTO_FAN_PIN -1
+#endif
 #define E2_AUTO_FAN_PIN -1
 #define E3_AUTO_FAN_PIN -1
 #define E4_AUTO_FAN_PIN -1
-#define CHAMBER_AUTO_FAN_PIN -1
 #define EXTRUDER_AUTO_FAN_TEMPERATURE 50
 #define EXTRUDER_AUTO_FAN_SPEED   255  // == full speed
 
@@ -260,13 +264,13 @@
 /**
  * M355 Case Light on-off / brightness
  */
-//#define CASE_LIGHT_ENABLE
+#define CASE_LIGHT_ENABLE
 #if ENABLED(CASE_LIGHT_ENABLE)
-  //#define CASE_LIGHT_PIN 4                  // Override the default pin if needed
+  //#define CASE_LIGHT_PIN 8                  // Override the default pin if needed
   #define INVERT_CASE_LIGHT false             // Set true if Case Light is ON when pin is LOW
   #define CASE_LIGHT_DEFAULT_ON true          // Set default power-up state on
-  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // Set default power-up brightness (0-255, requires PWM pin)
-  //#define MENU_ITEM_CASE_LIGHT              // Add a Case Light option to the LCD main menu
+  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 255   // Set default power-up brightness (0-255, requires PWM pin)
+  #define MENU_ITEM_CASE_LIGHT              // Add a Case Light option to the LCD main menu
   //#define CASE_LIGHT_USE_NEOPIXEL           // Use Neopixel LED as case light, requires NEOPIXEL_LED.
   #if ENABLED(CASE_LIGHT_USE_NEOPIXEL)
     #define CASE_LIGHT_NEOPIXEL_COLOR { 255, 255, 255, 255 } // { Red, Green, Blue, White }
@@ -331,22 +335,21 @@
   #endif
 #endif
 
-/**
- * Dual X Carriage
- *
- * This setup has two X carriages that can move independently, each with its own hotend.
- * The carriages can be used to print an object with two colors or materials, or in
- * "duplication mode" it can print two identical or X-mirrored objects simultaneously.
- * The inactive carriage is parked automatically to prevent oozing.
- * X1 is the left carriage, X2 the right. They park and home at opposite ends of the X axis.
- * By default the X2 stepper is assigned to the first unused E plug on the board.
- */
-//#define DUAL_X_CARRIAGE
+// Enable this for dual x-carriage printers.
+// A dual x-carriage design has the advantage that the inactive extruder can be parked which
+// prevents hot-end ooze contaminating the print. It also reduces the weight of each x-carriage
+// allowing faster printing speeds. Connect your X2 stepper to the first unused E plug.
+#define DUAL_X_CARRIAGE
 #if ENABLED(DUAL_X_CARRIAGE)
-  #define X1_MIN_POS X_MIN_POS  // set minimum to ensure first x-carriage doesn't hit the parked second X-carriage
-  #define X1_MAX_POS X_BED_SIZE // set maximum to ensure first x-carriage doesn't hit the parked second X-carriage
-  #define X2_MIN_POS 80     // set minimum to ensure second x-carriage doesn't hit the parked first X-carriage
-  #define X2_MAX_POS 353    // set maximum to the distance between toolheads when both heads are homed
+  // Configuration for second X-carriage
+  // Note: the first x-carriage is defined as the x-carriage which homes to the minimum endstop;
+  // the second x-carriage always homes to the maximum endstop.
+  #define X2_MIN_POS 0     // set minimum to ensure second x-carriage doesn't hit the parked first X-carriage
+  #if DISABLED(TREX3) || ENABLED(TREX3_UPGRADE)
+    #define X2_MAX_POS 442       // Set this to the distance between toolheads when both heads are homed
+  #else
+    #define X2_MAX_POS 446       // Set this to the distance between toolheads when both heads are homed
+  #endif
   #define X2_HOME_DIR 1     // the second X-carriage always homes to the maximum endstop position
   #define X2_HOME_POS X2_MAX_POS // default home position is the maximum carriage position
       // However: In this mode the HOTEND_OFFSET_X value for the second extruder provides a software
@@ -364,14 +367,14 @@
   //                                    once. (2nd extruder x offset and temp offset are set using: M605 S2 [Xnnn] [Rmmm])
 
   // This is the default power-up mode which can be later using M605.
-  #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_FULL_CONTROL_MODE
+  #define DEFAULT_DUAL_X_CARRIAGE_MODE DXC_AUTO_PARK_MODE
 
   // Default settings in "Auto-park Mode"
   #define TOOLCHANGE_PARK_ZLIFT   0.2      // the distance to raise Z axis when parking an extruder
   #define TOOLCHANGE_UNPARK_ZLIFT 1        // the distance to raise Z axis when unparking an extruder
 
   // Default x offset in duplication mode (typically set to half print bed width)
-  #define DEFAULT_DUPLICATION_X_OFFSET 100
+  #define DEFAULT_DUPLICATION_X_OFFSET 200
 
 #endif // DUAL_X_CARRIAGE
 
@@ -386,7 +389,7 @@
 #define Y_HOME_BUMP_MM 5
 #define Z_HOME_BUMP_MM 2
 #define HOMING_BUMP_DIVISOR { 2, 2, 4 }  // Re-Bump Speed Divisor (Divides the Homing Feedrate)
-//#define QUICK_HOME                     // If homing includes X and Y, do a diagonal move initially
+#define QUICK_HOME                     // If homing includes X and Y, do a diagonal move initially
 
 // When G28 is called, this option will make Y home before X
 //#define HOME_Y_BEFORE_X
@@ -449,21 +452,14 @@
 //
 // Use Junction Deviation instead of traditional Jerk Limiting
 //
-//#define JUNCTION_DEVIATION
+#define JUNCTION_DEVIATION
 #if ENABLED(JUNCTION_DEVIATION)
-  #define JUNCTION_DEVIATION_MM 0.02  // (mm) Distance from real junction edge
+  #define JUNCTION_DEVIATION_MM 0.08
+  //#define JUNCTION_DEVIATION_INCLUDE_E
 #endif
 
-/**
- * Adaptive Step Smoothing increases the resolution of multi-axis moves, particularly at step frequencies
- * below 1kHz (for AVR) or 10kHz (for ARM), where aliasing between axes in multi-axis moves causes audible
- * vibration and surface artifacts. The algorithm adapts to provide the best possible step smoothing at the
- * lowest stepping frequencies.
- */
-//#define ADAPTIVE_STEP_SMOOTHING
-
 // Microstep setting (Only functional when stepper driver microstep pins are connected to MCU.
-#define MICROSTEP_MODES { 16, 16, 16, 16, 16 } // [1,2,4,8,16]
+#define MICROSTEP_MODES {16,16,16,16,16} // [1,2,4,8,16]
 
 /**
  *  @section  stepper motor current
@@ -524,19 +520,19 @@
 // @section lcd
 
 // Include a page of printer information in the LCD Main Menu
-//#define LCD_INFO_MENU
+#define LCD_INFO_MENU
 
 // Scroll a longer status message into view
-//#define STATUS_MESSAGE_SCROLLING
+#define STATUS_MESSAGE_SCROLLING
 
 // On the Info Screen, display XY with one decimal place when possible
-//#define LCD_DECIMAL_SMALL_XY
+#define LCD_DECIMAL_SMALL_XY
 
 // The timeout (in ms) to return to the status screen from sub-menus
-//#define LCD_TIMEOUT_TO_STATUS 15000
+#define LCD_TIMEOUT_TO_STATUS 15000
 
 // Add an 'M73' G-code to set the current percentage
-//#define LCD_SET_PROGRESS_MANUALLY
+#define LCD_SET_PROGRESS_MANUALLY
 
 #if ENABLED(SDSUPPORT) || ENABLED(LCD_SET_PROGRESS_MANUALLY)
   //#define LCD_PROGRESS_BAR              // Show a progress bar on HD44780 LCDs for SD printing
@@ -594,10 +590,6 @@
    * point in the file.
    */
   //#define POWER_LOSS_RECOVERY
-  #if ENABLED(POWER_LOSS_RECOVERY)
-    //#define POWER_LOSS_PIN   44     // Pin to detect power loss
-    //#define POWER_LOSS_STATE HIGH   // State of pin indicating power loss
-  #endif
 
   /**
    * Sort SD file listings in alphabetical order.
@@ -626,9 +618,9 @@
 
   // SD Card Sorting options
   #if ENABLED(SDCARD_SORT_ALPHA)
-    #define SDSORT_LIMIT       40     // Maximum number of sorted items (10-256). Costs 27 bytes each.
+    #define SDSORT_LIMIT       30     // Maximum number of sorted items (10-256). Costs 27 bytes each.
     #define FOLDER_SORTING     -1     // -1=above  0=none  1=below
-    #define SDSORT_GCODE       false  // Allow turning sorting on/off with LCD and M34 g-code.
+    #define SDSORT_GCODE       true  // Allow turning sorting on/off with LCD and M34 g-code.
     #define SDSORT_USES_RAM    false  // Pre-allocate a static array for faster pre-sorting.
     #define SDSORT_USES_STACK  false  // Prefer the stack for pre-sorting to give back some SRAM. (Negated by next 2 options.)
     #define SDSORT_CACHE_NAMES false  // Keep sorted items in RAM longer for speedy performance. Most expensive option.
@@ -638,10 +630,10 @@
   #endif
 
   // This allows hosts to request long names for files and folders with M33
-  //#define LONG_FILENAME_HOST_SUPPORT
+  #define LONG_FILENAME_HOST_SUPPORT
 
   // Enable this option to scroll long filenames in the SD card menu
-  //#define SCROLL_LONG_FILENAMES
+  #define SCROLL_LONG_FILENAMES
 
   /**
    * This option allows you to abort SD printing when any endstop is triggered.
@@ -660,7 +652,7 @@
   /**
    * Auto-report SdCard status with M27 S<seconds>
    */
-  //#define AUTO_REPORT_SD_STATUS
+  #define AUTO_REPORT_SD_STATUS
 
 #endif // SDSUPPORT
 
@@ -688,7 +680,7 @@
 
   // A bigger font is available for edit items. Costs 3120 bytes of PROGMEM.
   // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
-  //#define USE_BIG_EDIT_FONT
+  #define USE_BIG_EDIT_FONT
 
   // A smaller font may be used on the Info Screen. Costs 2300 bytes of PROGMEM.
   // Western only. Not available for Cyrillic, Kana, Turkish, Greek, or Chinese.
@@ -744,16 +736,16 @@
  *
  * Warning: Does not respect endstops!
  */
-//#define BABYSTEPPING
+#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
   //#define BABYSTEP_XY              // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false    // Change if Z babysteps should go the other way
-  #define BABYSTEP_MULTIPLICATOR 1   // Babysteps are very small. Increase for faster motion.
-  //#define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
-  //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
+  #define BABYSTEP_MULTIPLICATOR 10   // Babysteps are very small. Increase for faster motion.
+  #define BABYSTEP_ZPROBE_OFFSET   // Enable to combine M851 and Babystepping
+  #define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.
   #define DOUBLECLICK_MAX_INTERVAL 1250 // Maximum interval between clicks, in milliseconds.
                                         // Note: Extra time may be added to mitigate controller latency.
-  //#define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
+  #define BABYSTEP_ZPROBE_GFX_OVERLAY // Enable graphical overlay on Z-offset editor
 #endif
 
 // @section extruder
@@ -774,9 +766,11 @@
  * See http://marlinfw.org/docs/features/lin_advance.html for full instructions.
  * Mention @Sebastianv650 on GitHub to alert the author of any issues.
  */
-//#define LIN_ADVANCE
+#if DISABLED(E_2208) || ENABLED(E_Spreadcycle)
+  #define LIN_ADVANCE
+#endif
 #if ENABLED(LIN_ADVANCE)
-  #define LIN_ADVANCE_K 0.22  // Unit: mm compression per 1mm/s extruder speed
+  #define LIN_ADVANCE_K 0.07  // Unit: mm compression per 1mm/s extruder speed
   //#define LA_DEBUG          // If enabled, this will generate debug information output over USB.
 #endif
 
@@ -784,10 +778,10 @@
 
 #if ENABLED(MESH_BED_LEVELING) || ENABLED(AUTO_BED_LEVELING_UBL)
   // Override the mesh area if the automatic (max) area is too large
-  //#define MESH_MIN_X MESH_INSET
-  //#define MESH_MIN_Y MESH_INSET
-  //#define MESH_MAX_X X_BED_SIZE - (MESH_INSET)
-  //#define MESH_MAX_Y Y_BED_SIZE - (MESH_INSET)
+  //#define MESH_MIN_X 50
+  //#define MESH_MIN_Y 0
+  //#define MESH_MAX_X X_BED_SIZE - (50)
+  //#define MESH_MAX_Y Y_BED_SIZE - (0)
 #endif
 
 // @section extras
@@ -816,46 +810,10 @@
 // Moves (or segments) with fewer steps than this will be joined with the next move
 #define MIN_STEPS_PER_SEGMENT 6
 
-/**
- * Minimum delay after setting the stepper DIR (in ns)
- *     0 : No delay (Expect at least 10µS since one Stepper ISR must transpire)
- *    20 : Minimum for TMC2xxx drivers
- *   200 : Minimum for A4988 drivers
- *   500 : Minimum for LV8729 drivers (guess, no info in datasheet)
- *   650 : Minimum for DRV8825 drivers
- *  1500 : Minimum for TB6600 drivers (guess, no info in datasheet)
- * 15000 : Minimum for TB6560 drivers (guess, no info in datasheet)
- *
- * Override the default value based on the driver type set in Configuration.h.
- */
-//#define MINIMUM_STEPPER_DIR_DELAY 650
-
-/**
- * Minimum stepper driver pulse width (in µs)
- *   0 : Smallest possible width the MCU can produce, compatible with TMC2xxx drivers
- *   1 : Minimum for A4988 stepper drivers
- *   1 : Minimum for LV8729 stepper drivers
- *   2 : Minimum for DRV8825 stepper drivers
- *   3 : Minimum for TB6600 stepper drivers
- *  30 : Minimum for TB6560 stepper drivers
- *
- * Override the default value based on the driver type set in Configuration.h.
- */
-//#define MINIMUM_STEPPER_PULSE 2
-
-/**
- * Maximum stepping rate (in Hz) the stepper driver allows
- *  If undefined, defaults to 1MHz / (2 * MINIMUM_STEPPER_PULSE)
- *  500000 : Maximum for A4988 stepper driver
- *  400000 : Maximum for TMC2xxx stepper drivers
- *  250000 : Maximum for DRV8825 stepper driver
- *  150000 : Maximum for TB6600 stepper driver
- *  130000 : Maximum for LV8729 stepper driver
- *   15000 : Maximum for TB6560 stepper driver
- *
- * Override the default value based on the driver type set in Configuration.h.
- */
-//#define MAXIMUM_STEPPER_RATE 250000
+// The minimum pulse width (in µs) for stepping a stepper.
+// Set this if you find stepping unreliable, or if using a very fast CPU.
+// 0 is OK for AVR, 0 is OK for A4989 drivers, 2 is needed for DRV8825 drivers
+#define MINIMUM_STEPPER_PULSE 2
 
 // @section temperature
 
@@ -917,7 +875,7 @@
 // enter the serial receive buffer, so they cannot be blocked.
 // Currently handles M108, M112, M410
 // Does not work on boards using AT90USB (USBCON) processors!
-//#define EMERGENCY_PARSER
+#define EMERGENCY_PARSER
 
 // Bad Serial-connections can miss a received command by sending an 'ok'
 // Therefore some clients abort after 30 seconds in a timeout.
@@ -926,7 +884,7 @@
 //#define NO_TIMEOUTS 1000 // Milliseconds
 
 // Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary.
-//#define ADVANCED_OK
+#define ADVANCED_OK
 
 // @section extras
 
@@ -978,57 +936,67 @@
  * Requires NOZZLE_PARK_FEATURE.
  * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
  */
-//#define ADVANCED_PAUSE_FEATURE
+#define ADVANCED_PAUSE_FEATURE
 #if ENABLED(ADVANCED_PAUSE_FEATURE)
   #define PAUSE_PARK_RETRACT_FEEDRATE         60  // (mm/s) Initial retract feedrate.
-  #define PAUSE_PARK_RETRACT_LENGTH            2  // (mm) Initial retract.
+  #define PAUSE_PARK_RETRACT_LENGTH            4  // (mm) Initial retract.
                                                   // This short retract is done immediately, before parking the nozzle.
-  #define FILAMENT_CHANGE_UNLOAD_FEEDRATE     10  // (mm/s) Unload filament feedrate. This can be pretty fast.
+  #define FILAMENT_CHANGE_UNLOAD_FEEDRATE     41  // (mm/s) Unload filament feedrate. This can be pretty fast.
   #define FILAMENT_CHANGE_UNLOAD_ACCEL        25  // (mm/s^2) Lower acceleration may allow a faster feedrate.
-  #define FILAMENT_CHANGE_UNLOAD_LENGTH      100  // (mm) The length of filament for a complete unload.
+  #define FILAMENT_CHANGE_UNLOAD_LENGTH      50  // (mm) The length of filament for a complete unload.
                                                   //   For Bowden, the full length of the tube and nozzle.
                                                   //   For direct drive, the full length of the nozzle.
                                                   //   Set to 0 for manual unloading.
   #define FILAMENT_CHANGE_SLOW_LOAD_FEEDRATE   6  // (mm/s) Slow move when starting load.
   #define FILAMENT_CHANGE_SLOW_LOAD_LENGTH     0  // (mm) Slow length, to allow time to insert material.
                                                   // 0 to disable start loading and skip to fast load only
-  #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE   6  // (mm/s) Load filament feedrate. This can be pretty fast.
+  #define FILAMENT_CHANGE_FAST_LOAD_FEEDRATE  30  // (mm/s) Load filament feedrate. This can be pretty fast.
   #define FILAMENT_CHANGE_FAST_LOAD_ACCEL     25  // (mm/s^2) Lower acceleration may allow a faster feedrate.
-  #define FILAMENT_CHANGE_FAST_LOAD_LENGTH     0  // (mm) Load length of filament, from extruder gear to nozzle.
+  #define FILAMENT_CHANGE_FAST_LOAD_LENGTH   50  // (mm) Load length of filament, from extruder gear to nozzle.
                                                   //   For Bowden, the full length of the tube and nozzle.
                                                   //   For direct drive, the full length of the nozzle.
   //#define ADVANCED_PAUSE_CONTINUOUS_PURGE       // Purge continuously up to the purge length until interrupted.
   #define ADVANCED_PAUSE_PURGE_FEEDRATE        3  // (mm/s) Extrude feedrate (after loading). Should be slower than load feedrate.
-  #define ADVANCED_PAUSE_PURGE_LENGTH         50  // (mm) Length to extrude after loading.
+  #define ADVANCED_PAUSE_PURGE_LENGTH         20  // (mm) Length to extrude after loading.
                                                   //   Set to 0 for manual extrusion.
                                                   //   Filament can be extruded repeatedly from the Filament Change menu
                                                   //   until extrusion is consistent, and to purge old filament.
 
                                                   // Filament Unload does a Retract, Delay, and Purge first:
-  #define FILAMENT_UNLOAD_RETRACT_LENGTH      13  // (mm) Unload initial retract length.
+  #define FILAMENT_UNLOAD_RETRACT_LENGTH       4  // (mm) Unload initial retract length.
   #define FILAMENT_UNLOAD_DELAY             5000  // (ms) Delay for the filament to cool after retract.
-  #define FILAMENT_UNLOAD_PURGE_LENGTH         8  // (mm) An unretract is done, then this length is purged.
-
+  #define FILAMENT_UNLOAD_PURGE_LENGTH         0  // (mm) An unretract is done, then this length is purged.
   #define PAUSE_PARK_NOZZLE_TIMEOUT           45  // (seconds) Time limit before the nozzle is turned off for safety.
-  #define FILAMENT_CHANGE_ALERT_BEEPS         10  // Number of alert beeps to play when a response is needed.
+  #define FILAMENT_CHANGE_ALERT_BEEPS          3  // Number of alert beeps to play when a response is needed.
   #define PAUSE_PARK_NO_STEPPER_TIMEOUT           // Enable for XYZ steppers to stay powered on during filament change.
 
-  //#define PARK_HEAD_ON_PAUSE                    // Park the nozzle during pause and filament change.
-  //#define HOME_BEFORE_FILAMENT_CHANGE           // Ensure homing has been completed prior to parking for filament change
+  #define PARK_HEAD_ON_PAUSE                      // Park the nozzle during pause and filament change.
+  #define HOME_BEFORE_FILAMENT_CHANGE             // Ensure homing has been completed prior to parking for filament change
 
-  //#define FILAMENT_LOAD_UNLOAD_GCODES           // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
+  #define FILAMENT_LOAD_UNLOAD_GCODES           // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
   //#define FILAMENT_UNLOAD_ALL_EXTRUDERS         // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
 #endif
 
 // @section tmc
 
 /**
- * TMC26X Stepper Driver options
- *
- * The TMC26XStepper library is required for this stepper driver.
- * https://github.com/trinamic/TMC26XStepper
+ * Enable this section if you have TMC26X motor drivers.
+ * You will need to import the TMC26XStepper library into the Arduino IDE for this
+ * (https://github.com/trinamic/TMC26XStepper.git)
  */
-#if HAS_DRIVER(TMC26X)
+//#define HAVE_TMC26X
+#if ENABLED(HAVE_TMC26X)  // Choose your axes here. This is mandatory!
+  //#define X_IS_TMC26X
+  //#define X2_IS_TMC26X
+  //#define Y_IS_TMC26X
+  //#define Y2_IS_TMC26X
+  //#define Z_IS_TMC26X
+  //#define Z2_IS_TMC26X
+  //#define E0_IS_TMC26X
+  //#define E1_IS_TMC26X
+  //#define E2_IS_TMC26X
+  //#define E3_IS_TMC26X
+  //#define E4_IS_TMC26X
 
   #define X_MAX_CURRENT     1000 // in mA
   #define X_SENSE_RESISTOR    91 // in mOhms
@@ -1074,21 +1042,39 @@
   #define E4_SENSE_RESISTOR   91
   #define E4_MICROSTEPS       16
 
-#endif // TMC26X
+#endif
 
 // @section tmc_smart
 
 /**
- * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
- * the hardware SPI interface on your board and define the required CS pins
- * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
- * You may also use software SPI if you wish to use general purpose IO pins.
+ * Enable this for SilentStepStick Trinamic TMC2130 SPI-configurable stepper drivers.
  *
  * You'll also need the TMC2130Stepper Arduino library
  * (https://github.com/teemuatlut/TMC2130Stepper).
  *
- * To use TMC2208 stepper UART-configurable stepper drivers
- * connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
+ * To use TMC2130 stepper drivers in SPI mode connect your SPI pins to
+ * the hardware SPI interface on your board and define the required CS pins
+ * in your `pins_MYBOARD.h` file. (e.g., RAMPS 1.4 uses AUX3 pins `X_CS_PIN 53`, `Y_CS_PIN 49`, etc.).
+ * You may also use software SPI if you wish to use general purpose IO pins.
+ */
+//#define HAVE_TMC2130
+#if ENABLED(HAVE_TMC2130)  // Choose your axes here. This is mandatory!
+  //#define X_IS_TMC2130
+  //#define X2_IS_TMC2130
+  //#define Y_IS_TMC2130
+  //#define Y2_IS_TMC2130
+  //#define Z_IS_TMC2130
+  //#define Z2_IS_TMC2130
+  //#define E0_IS_TMC2130
+  //#define E1_IS_TMC2130
+  //#define E2_IS_TMC2130
+  //#define E3_IS_TMC2130
+  //#define E4_IS_TMC2130
+#endif
+
+/**
+ * Enable this for SilentStepStick Trinamic TMC2208 UART-configurable stepper drivers.
+ * Connect #_SERIAL_TX_PIN to the driver side PDN_UART pin with a 1K resistor.
  * To use the reading capabilities, also connect #_SERIAL_RX_PIN
  * to PDN_UART without a resistor.
  * The drivers can also be used with hardware serial.
@@ -1096,7 +1082,22 @@
  * You'll also need the TMC2208Stepper Arduino library
  * (https://github.com/teemuatlut/TMC2208Stepper).
  */
-#if HAS_TRINAMIC
+//#define HAVE_TMC2208
+#if ENABLED(HAVE_TMC2208)  // Choose your axes here. This is mandatory!
+  //#define X_IS_TMC2208
+  //#define X2_IS_TMC2208
+  //#define Y_IS_TMC2208
+  //#define Y2_IS_TMC2208
+  //#define Z_IS_TMC2208
+  //#define Z2_IS_TMC2208
+  //#define E0_IS_TMC2208
+  //#define E1_IS_TMC2208
+  //#define E2_IS_TMC2208
+  //#define E3_IS_TMC2208
+  //#define E4_IS_TMC2208
+#endif
+
+#if ENABLED(HAVE_TMC2130) || ENABLED(HAVE_TMC2208)
 
   #define R_SENSE           0.11  // R_sense resistor for SilentStepStick2130
   #define HOLD_MULTIPLIER    0.5  // Scales down the holding current from run current
@@ -1251,12 +1252,25 @@
 // @section L6470
 
 /**
- * L6470 Stepper Driver options
- *
- * The Arduino-L6470 library is required for this stepper driver.
- * https://github.com/ameyer/Arduino-L6470
+ * Enable this section if you have L6470 motor drivers.
+ * You need to import the L6470 library into the Arduino IDE for this.
+ * (https://github.com/ameyer/Arduino-L6470)
  */
-#if HAS_DRIVER(L6470)
+
+//#define HAVE_L6470DRIVER
+#if ENABLED(HAVE_L6470DRIVER)
+
+  //#define X_IS_L6470
+  //#define X2_IS_L6470
+  //#define Y_IS_L6470
+  //#define Y2_IS_L6470
+  //#define Z_IS_L6470
+  //#define Z2_IS_L6470
+  //#define E0_IS_L6470
+  //#define E1_IS_L6470
+  //#define E2_IS_L6470
+  //#define E3_IS_L6470
+  //#define E4_IS_L6470
 
   #define X_MICROSTEPS      16 // number of microsteps
   #define X_OVERCURRENT   2000 // maxc current in mA. If the current goes over this value, the driver will switch off
@@ -1302,7 +1316,7 @@
   #define E4_OVERCURRENT  2000
   #define E4_STALLCURRENT 1500
 
-#endif // L6470
+#endif
 
 /**
  * TWI/I2C BUS
@@ -1338,7 +1352,6 @@
 #define I2C_SLAVE_ADDRESS  0 // Set a value from 8 to 127 to act as a slave
 
 // @section extras
-
 /**
  * Spindle & Laser control
  *
@@ -1354,19 +1367,21 @@
  *
  * See http://marlinfw.org/docs/configuration/laser_spindle.html for more config details.
  */
-//#define SPINDLE_LASER_ENABLE
+#if ENABLED(TREX3)
+#define SPINDLE_LASER_ENABLE
+#endif
 #if ENABLED(SPINDLE_LASER_ENABLE)
 
-  #define SPINDLE_LASER_ENABLE_INVERT   false  // set to "true" if the on/off function is reversed
-  #define SPINDLE_LASER_PWM             true   // set to true if your controller supports setting the speed/power
-  #define SPINDLE_LASER_PWM_INVERT      true   // set to "true" if the speed/power goes up when you want it to go slower
-  #define SPINDLE_LASER_POWERUP_DELAY   5000   // delay in milliseconds to allow the spindle/laser to come up to speed/power
-  #define SPINDLE_LASER_POWERDOWN_DELAY 5000   // delay in milliseconds to allow the spindle to stop
-  #define SPINDLE_DIR_CHANGE            true   // set to true if your spindle controller supports changing spindle direction
-  #define SPINDLE_INVERT_DIR            false
-  #define SPINDLE_STOP_ON_DIR_CHANGE    true   // set to true if Marlin should stop the spindle before changing rotation direction
+#define SPINDLE_LASER_ENABLE_INVERT true // set to "true" if the on/off function is reversed
+#define SPINDLE_LASER_PWM false          // set to true if your controller supports setting the speed/power
+#define SPINDLE_LASER_PWM_INVERT true    // set to "true" if the speed/power goes up when you want it to go slower
+#define SPINDLE_LASER_POWERUP_DELAY 1    // delay in milliseconds to allow the spindle/laser to come up to speed/power
+#define SPINDLE_LASER_POWERDOWN_DELAY 1  // delay in milliseconds to allow the spindle to stop
+#define SPINDLE_DIR_CHANGE false         // set to true if your spindle controller supports changing spindle direction
+#define SPINDLE_INVERT_DIR false
+#define SPINDLE_STOP_ON_DIR_CHANGE false // set to true if Marlin should stop the spindle before changing rotation direction
 
-  /**
+/**
    *  The M3 & M4 commands use the following equation to convert PWM duty cycle to speed/power
    *
    *  SPEED/POWER = PWM duty cycle * SPEED_POWER_SLOPE + SPEED_POWER_INTERCEPT
@@ -1375,15 +1390,15 @@
    *  set the following for your controller (ALL MUST BE SET)
    */
 
-  #define SPEED_POWER_SLOPE    118.4
-  #define SPEED_POWER_INTERCEPT  0
-  #define SPEED_POWER_MIN     5000
-  #define SPEED_POWER_MAX    30000    // SuperPID router controller 0 - 30,000 RPM
+#define SPEED_POWER_SLOPE 118.4
+#define SPEED_POWER_INTERCEPT 0
+#define SPEED_POWER_MIN 5000
+#define SPEED_POWER_MAX 30000 // SuperPID router controller 0 - 30,000 RPM
 
-  //#define SPEED_POWER_SLOPE      0.3922
-  //#define SPEED_POWER_INTERCEPT  0
-  //#define SPEED_POWER_MIN       10
-  //#define SPEED_POWER_MAX      100      // 0-100%
+//#define SPEED_POWER_SLOPE      0.3922
+//#define SPEED_POWER_INTERCEPT  0
+//#define SPEED_POWER_MIN       10
+//#define SPEED_POWER_MAX      100      // 0-100%
 #endif
 
 /**
@@ -1484,26 +1499,38 @@
 /**
  * User-defined menu items that execute custom GCode
  */
-//#define CUSTOM_USER_MENUS
+ #define CUSTOM_USER_MENUS
 #if ENABLED(CUSTOM_USER_MENUS)
-  #define USER_SCRIPT_DONE "M117 User Script Done"
-  #define USER_SCRIPT_AUDIBLE_FEEDBACK
-  //#define USER_SCRIPT_RETURN  // Return to status screen after a script
+  //#define USER_SCRIPT_DONE "M117 User Script Done"
+  //#define USER_SCRIPT_AUDIBLE_FEEDBACK
+  #define USER_SCRIPT_RETURN  // Return to status screen after a script
+  #define MSG_USER_MENU "Setup Menu"
 
-  #define USER_DESC_1 "Home & UBL Info"
-  #define USER_GCODE_1 "G28\nG29 W"
+  #if ENABLED(TREX3)
+    #define COMMFANNSPEED " "
+  #else
+    #define COMMFANNSPEED  "M106 S128 \n"
+  #endif
 
-  #define USER_DESC_2 "Preheat for PLA"
-  #define USER_GCODE_2 "M140 S" STRINGIFY(PREHEAT_1_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_1_TEMP_HOTEND)
+  #define USER_DESC_1 "1. Run UBL"
+  #define USER_DESC_2 "2. Set Z Offset"
 
-  #define USER_DESC_3 "Preheat for ABS"
-  #define USER_GCODE_3 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nM104 S" STRINGIFY(PREHEAT_2_TEMP_HOTEND)
+  #if ENABLED(ABL_Bilinear)
+    #define USER_GCODE_1 "M502 \n M500 \n M501 \n M190 S60 \n T0 \n G28 \n G29 \n M500 \n G28 \n M420 S1 \n " COMMFANNSPEED " M109 S225 \n G1 X100 Y 100 \n G1 Z0 \n M77 \n M400 \n M117 Set Z Offset"
+    #define USER_GCODE_2 "M190 S60 \n " COMMFANNSPEED " M104 235 \n G28 \n M420 S1 \n G1 X100 Y 100 \n G1 Z0"
+  #else
+    #define USER_GCODE_1 "M502 \n M500 \n M501 \n M190 S60 \n T0 \n G28 \n G29 P1 \n G29 S1 \n G29 S0 \n G29 F 10.0 \n G29 A \n M500 \n G28 \n G29 L1 \n " COMMFANNSPEED " M109 S225 \n G1 X150 Y 150 \n G1 Z0 \n M77 \n M117 Set Z Offset"
+    #define USER_GCODE_2 "M190 S60 \n " COMMFANNSPEED " M104 235 \n G28 \n G29 L1 \n G1 X100 Y 100 \n G1 Z0"
+  #endif
 
-  #define USER_DESC_4 "Heat Bed/Home/Level"
-  #define USER_GCODE_4 "M140 S" STRINGIFY(PREHEAT_2_TEMP_BED) "\nG28\nG29"
+  #define USER_DESC_3 "Store Settings"
+  #define USER_GCODE_3 "M500"
 
-  #define USER_DESC_5 "Home & Info"
-  #define USER_GCODE_5 "G28\nM503"
+  #define USER_DESC_5 "PID Tune Bed"
+  #define USER_GCODE_5 "M303E-1S75U \n M500 \n M117 PID Bed Done"
+
+  #define USER_DESC_4 "PID Tune Tool 1"
+  #define USER_GCODE_4 "M106 S128 \n M303 C8 S225 E0 U \n M500 \n M117 PID Tune L Done"
 #endif
 
 /**
@@ -1518,8 +1545,8 @@
  * Will be sent in the form '//action:ACTION_ON_PAUSE', e.g. '//action:pause'.
  * The host must be configured to handle the action command.
  */
-//#define ACTION_ON_PAUSE "pause"
-//#define ACTION_ON_RESUME "resume"
+#define ACTION_ON_PAUSE "pause"
+#define ACTION_ON_RESUME "resume"
 
 //===========================================================================
 //====================== I2C Position Encoder Settings ======================
@@ -1608,29 +1635,27 @@
 /**
  * MAX7219 Debug Matrix
  *
- * Add support for a low-cost 8x8 LED Matrix based on the Max7219 chip as a realtime status display.
- * Requires 3 signal wires. Some useful debug options are included to demonstrate its usage.
+ * Add support for a low-cost 8x8 LED Matrix based on the Max7219 chip, which can be used as a status
+ * display. Requires 3 signal wires. Some useful debug options are included to demonstrate its usage.
+ *
+ * Fully assembled MAX7219 boards can be found on the internet for under $2(US).
+ * For example, see https://www.ebay.com/sch/i.html?_nkw=332349290049
  */
 //#define MAX7219_DEBUG
 #if ENABLED(MAX7219_DEBUG)
-  #define MAX7219_CLK_PIN   64
-  #define MAX7219_DIN_PIN   57
-  #define MAX7219_LOAD_PIN  44
+  #define MAX7219_CLK_PIN   64  // 77 on Re-ARM       // Configuration of the 3 pins to control the display
+  #define MAX7219_DIN_PIN   57  // 78 on Re-ARM
+  #define MAX7219_LOAD_PIN  44  // 79 on Re-ARM
 
-  //#define MAX7219_GCODE          // Add the M7219 G-code to control the LED matrix
-  #define MAX7219_INIT_TEST    2   // Do a test pattern at initialization (Set to 2 for spiral)
-  #define MAX7219_NUMBER_UNITS 1   // Number of Max7219 units in chain.
-  #define MAX7219_ROTATE       0   // Rotate the display clockwise (in multiples of +/- 90°)
-                                   // connector at:  right=0   bottom=-90  top=90  left=180
   /**
    * Sample debug features
    * If you add more debug displays, be careful to avoid conflicts!
    */
   #define MAX7219_DEBUG_PRINTER_ALIVE    // Blink corner LED of 8x8 matrix to show that the firmware is functioning
-  #define MAX7219_DEBUG_PLANNER_HEAD  3  // Show the planner queue head position on this and the next LED matrix row
-  #define MAX7219_DEBUG_PLANNER_TAIL  5  // Show the planner queue tail position on this and the next LED matrix row
+  #define MAX7219_DEBUG_STEPPER_HEAD  3  // Show the stepper queue head position on this and the next LED matrix row
+  #define MAX7219_DEBUG_STEPPER_TAIL  5  // Show the stepper queue tail position on this and the next LED matrix row
 
-  #define MAX7219_DEBUG_PLANNER_QUEUE 0  // Show the current planner queue depth on this and the next LED matrix row
+  #define MAX7219_DEBUG_STEPPER_QUEUE 0  // Show the current stepper queue depth on this and the next LED matrix row
                                          // If you experience stuttering, reboots, etc. this option can reveal how
                                          // tweaks made to the configuration are affecting the printer in real-time.
 #endif
@@ -1648,7 +1673,4 @@
                               // Default behaviour is limited to Z axis only.
 #endif
 
-// Enable Marlin dev mode which adds some special commands
-//#define MARLIN_DEV_MODE
-
-#endif // CONFIGURATION_ADV_H
+#endif // CONFIGURATION_ADV_H

Marlin/Marlin.h

@@ -55,7 +55,8 @@ void manage_inactivity(const bool ignore_stepper_queue=false);
 extern const char axis_codes[XYZE];
 
 #if ENABLED(DUAL_X_CARRIAGE) || ENABLED(DUAL_NOZZLE_DUPLICATION_MODE)
-  extern bool extruder_duplication_enabled;
+  extern bool extruder_duplication_enabled,
+              mirrored_duplication_mode;
 #endif
 
 #if HAS_X2_ENABLE

Marlin/Marlin_main.cpp

@@ -1305,7 +1305,8 @@ bool get_target_extruder_from_command(const uint16_t code) {
 }
 
 #if ENABLED(DUAL_X_CARRIAGE) || ENABLED(DUAL_NOZZLE_DUPLICATION_MODE)
-  bool extruder_duplication_enabled = false; // Used in Dual X mode 2
+  bool extruder_duplication_enabled,
+       mirrored_duplication_mode;
 #endif
 
 #if ENABLED(DUAL_X_CARRIAGE)
@@ -2092,11 +2093,16 @@ void clean_up_after_endstop_or_probe_move() {
         }
       }
 
+      #if ENABLED(BLTOUCH_FORCE_5V_MODE)
+        bltouch_command(BLTOUCH_5V_MODE);
+      #elif ENABLED(BLTOUCH_V3)
+        bltouch_command(BLTOUCH_OD_MODE);
+      #endif
+
       bltouch_command(deploy ? BLTOUCH_DEPLOY : BLTOUCH_STOW);
+      
       #if ENABLED(BLTOUCH_V3)
-        // The version 3 of BlTouch needs to switch to Alarm & Test mode after deploy
-        // or it keeps on pushing the probes out and ends up in error mode (collision).
-        if (deploy) bltouch_command(BLTOUCH_ALARM);
+        if (deploy) bltouch_command(BLTOUCH_SW_MODE);
       #endif
 
       #if ENABLED(DEBUG_LEVELING_FEATURE)
@@ -8238,7 +8244,7 @@ inline void gcode_M104() {
     thermalManager.setTargetHotend(temp, target_extruder);
 
     #if ENABLED(DUAL_X_CARRIAGE)
-      if (dual_x_carriage_mode == DXC_DUPLICATION_MODE && target_extruder == 0)
+      if (dual_x_carriage_mode >= DXC_DUPLICATION_MODE && target_extruder == 0)
         thermalManager.setTargetHotend(temp ? temp + duplicate_extruder_temp_offset : 0, 1);
     #endif
 
@@ -8393,7 +8399,7 @@ inline void gcode_M109() {
     thermalManager.setTargetHotend(temp, target_extruder);
 
     #if ENABLED(DUAL_X_CARRIAGE)
-      if (dual_x_carriage_mode == DXC_DUPLICATION_MODE && target_extruder == 0)
+      if (dual_x_carriage_mode >= DXC_DUPLICATION_MODE && target_extruder == 0)
         thermalManager.setTargetHotend(temp ? temp + duplicate_extruder_temp_offset : 0, 1);
     #endif
 
@@ -11071,47 +11077,80 @@ inline void gcode_M502() {
 
 #if ENABLED(DUAL_X_CARRIAGE)
 
-  /**
+/**
    * M605: Set dual x-carriage movement mode
    *
-   *    M605 S0: Full control mode. The slicer has full control over x-carriage movement
-   *    M605 S1: Auto-park mode. The inactive head will auto park/unpark without slicer involvement
-   *    M605 S2 [Xnnn] [Rmmm]: Duplication mode. The second extruder will duplicate the first with nnn
-   *                         units x-offset and an optional differential hotend temperature of
-   *                         mmm degrees. E.g., with "M605 S2 X100 R2" the second extruder will duplicate
-   *                         the first with a spacing of 100mm in the x direction and 2 degrees hotter.
+   *   M605 S0 : (FULL_CONTROL) The slicer has full control over both X-carriages and can achieve optimal travel
+   *             results as long as it supports dual X-carriages.
    *
-   *    Note: the X axis should be homed after changing dual x-carriage mode.
+   *   M605 S1 : (AUTO_PARK) The firmware automatically parks and unparks the X-carriages on tool-change so that
+   *             additional slicer support is not required.
+   *
+   *   M605 S2 X R : (DUPLICATION) The firmware moves the second X-carriage and extruder in synchronization with
+   *             the first X-carriage and extruder, to print 2 copies of the same object at the same time.
+   *             Set the constant X-offset and temperature differential with M605 S2 X[offs] R[deg] and
+   *             follow with "M605 S2" to initiate duplicated movement. For example, use "M605 S2 X100 R2" to
+   *             make a copy 100mm to the right with E1 2° hotter than E0.
+   *
+   *   M605 S3 : (MIRRORED) Formbot/Vivedino-inspired mirrored mode in which the second extruder duplicates
+   *             the movement of the first except the second extruder is reversed in the X axis.
+   *             The temperature differential and initial X offset must be set with "M605 S2 X[offs] R[deg]",
+   *             then followed by "M605 S3" to initiate mirrored movement.
+   *
+   *    M605 W  : IDEX What? command.
+   *
+   *    Note: the X axis should be homed after changing Dual X-carriage mode.
    */
   inline void gcode_M605() {
-    planner.synchronize();
+
+     planner.synchronize();
+
+    const DualXMode previous_mode = dual_x_carriage_mode;
     if (parser.seen('S')) dual_x_carriage_mode = (DualXMode)parser.value_byte();
-    switch (dual_x_carriage_mode) {
-      case DXC_FULL_CONTROL_MODE:
-      case DXC_AUTO_PARK_MODE:
-        break;
-      case DXC_DUPLICATION_MODE:
-        if (parser.seen('X')) duplicate_extruder_x_offset = MAX(parser.value_linear_units(), X2_MIN_POS - x_home_pos(0));
-        if (parser.seen('R')) duplicate_extruder_temp_offset = parser.value_celsius_diff();
-        SERIAL_ECHO_START();
-        SERIAL_ECHOPGM(MSG_HOTEND_OFFSET);
-        SERIAL_CHAR(' ');
-        SERIAL_ECHO(hotend_offset[X_AXIS][0]);
-        SERIAL_CHAR(',');
-        SERIAL_ECHO(hotend_offset[Y_AXIS][0]);
-        SERIAL_CHAR(' ');
-        SERIAL_ECHO(duplicate_extruder_x_offset);
-        SERIAL_CHAR(',');
-        SERIAL_ECHOLN(hotend_offset[Y_AXIS][1]);
-        break;
-      default:
-        dual_x_carriage_mode = DEFAULT_DUAL_X_CARRIAGE_MODE;
-        break;
+      SERIAL_ECHOLNPAIR("Mode Change ", dual_x_carriage_mode);
+      SERIAL_ECHOLNPAIR("From Mode ", previous_mode);
+
+      mirrored_duplication_mode = false;
+
+      if (dual_x_carriage_mode == DXC_MIRRORED_MODE) {
+        if (previous_mode != DXC_DUPLICATION_MODE) {
+          SERIAL_ECHOLN("Printer must be in DXC_DUPLICATION_MODE prior to ");
+          SERIAL_ECHOLN("specifying DXC_MIRRORED_MODE.");
+          dual_x_carriage_mode = DEFAULT_DUAL_X_CARRIAGE_MODE;
+          return;
+        }
+        SERIAL_ECHOLN("DXC_MIRRORED_MODE Set");
+        mirrored_duplication_mode = true;
+        float x_jog = current_position[X_AXIS] - .1;
+        for (uint8_t i = 2; --i;) {
+          planner.buffer_line(x_jog, current_position[Y_AXIS], current_position[Z_AXIS], current_position[E_AXIS], feedrate_mm_s, 0);
+          x_jog += .1;
+        }
+        return;
+      }
+
+      switch (dual_x_carriage_mode) {
+        case DXC_FULL_CONTROL_MODE:
+          SERIAL_ECHOLN("DXC_FULL_CONTROL_MODE Set");
+          break;
+        case DXC_AUTO_PARK_MODE:
+          SERIAL_ECHOLN("DXC_AUTO_PARK_MODE Set");
+          break;
+        case DXC_DUPLICATION_MODE:
+          SERIAL_ECHOLN("DXC_DUPLICATION_MODE Set");
+          if (parser.seen('X')) duplicate_extruder_x_offset = max(parser.value_linear_units(), X2_MIN_POS - x_home_pos(0));
+          if (parser.seen('R')) duplicate_extruder_temp_offset = parser.value_celsius_diff();
+          if (active_extruder != 0) tool_change(0);
+          break;
+        default:
+          SERIAL_ECHOLN("Default Mode Set");
+          dual_x_carriage_mode = DEFAULT_DUAL_X_CARRIAGE_MODE;
+          break;
+      }
+      active_extruder_parked = false;
+      extruder_duplication_enabled = false;
+      delayed_move_time = 0;
     }
-    active_extruder_parked = false;
-    extruder_duplication_enabled = false;
-    delayed_move_time = 0;
-  }
 
 #elif ENABLED(DUAL_NOZZLE_DUPLICATION_MODE)
 

Marlin/Version.h

@@ -35,20 +35,20 @@
   /**
    * Marlin release version identifier
    */
-  #define SHORT_BUILD_VERSION "bugfix-1.1.x"
+  #define SHORT_BUILD_VERSION "M119 Trex B3"
 
   /**
    * Verbose version identifier which should contain a reference to the location
    * from where the binary was downloaded or the source code was compiled.
    */
-  #define DETAILED_BUILD_VERSION SHORT_BUILD_VERSION " (Github)"
+  #define DETAILED_BUILD_VERSION SHORT_BUILD_VERSION " TM3D"
 
   /**
    * The STRING_DISTRIBUTION_DATE represents when the binary file was built,
    * here we define this default string as the date where the latest release
    * version was tagged.
    */
-  #define STRING_DISTRIBUTION_DATE "2018-07-31"
+  #define STRING_DISTRIBUTION_DATE "2019-06-22"
 
   /**
    * Required minimum Configuration.h and Configuration_adv.h file versions.
@@ -70,7 +70,7 @@
   /**
    * Defines a generic printer name to be output to the LCD after booting Marlin.
    */
-  #define MACHINE_NAME "3D Printer"
+  #define MACHINE_NAME "TM3DTrex"
 
   /**
    * The SOURCE_CODE_URL is the location where users will find the Marlin Source
@@ -78,7 +78,7 @@
    * has a distinct Github fork— the Source Code URL should just be the main
    * Marlin repository.
    */
-  #define SOURCE_CODE_URL "https://github.com/MarlinFirmware/Marlin"
+  #define SOURCE_CODE_URL "https://github.com/InsanityAutomation/Marlin/tree/Trex3_1.1.9"
 
   /**
    * Default generic printer UUID.
@@ -89,6 +89,6 @@
    * The WEBSITE_URL is the location where users can get more information such as
    * documentation about a specific Marlin release.
    */
-  #define WEBSITE_URL "http://marlinfw.org"
+  #define WEBSITE_URL "tinymachines3d.com"
 
 #endif // USE_AUTOMATIC_VERSIONING

Marlin/_Bootscreen.h

@@ -0,0 +1,105 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Custom Bitmap for splashscreen
+ *
+ * You may use one of the following tools to generate the C++ bitmap array from
+ * a black and white image:
+ *
+ *  - http://www.marlinfw.org/tools/u8glib/converter.html
+ *  - http://www.digole.com/tools/PicturetoC_Hex_converter.php
+ */
+#include <avr/pgmspace.h>
+
+#define CUSTOM_BOOTSCREEN_TIMEOUT   2500
+#define CUSTOM_BOOTSCREEN_BMPWIDTH  128
+#define CUSTOM_BOOTSCREEN_BMPHEIGHT 64
+
+const unsigned char custom_start_bmp[] PROGMEM = {
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFD, 0x55, 0x55, 0x55, 0x55, 0x55, 0x5F, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFE, 0x00, 0x00, 0x00, 0x00, 0x00, 0x3F, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFD, 0x00, 0x00, 0x07, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFE, 0x07, 0xC0, 0x05, 0x55, 0x55, 0x55, 0x55, 0x55, 0x5F, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFC, 0x0A, 0x20, 0x06, 0x00, 0x00, 0x00, 0x00, 0x00, 0x3F, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFE, 0x14, 0x10, 0x05, 0x00, 0x00, 0x07, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFC, 0x28, 0x08, 0x06, 0x07, 0xC0, 0x05, 0x55, 0x55, 0x55, 0x55, 0x55, 0x5F, 0xFF, 0xFF, 0xFF,
+0xFE, 0x54, 0x04, 0x04, 0x0A, 0x20, 0x06, 0x00, 0x00, 0x00, 0x00, 0x00, 0x3F, 0xFF, 0xFF, 0xFF,
+0xFC, 0x60, 0x04, 0x06, 0x14, 0x10, 0x05, 0x00, 0x00, 0x07, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFE, 0x50, 0x04, 0x04, 0x28, 0x08, 0x06, 0x07, 0xC0, 0x05, 0x55, 0x55, 0x55, 0x55, 0x55, 0x5F,
+0xFC, 0x60, 0x04, 0x06, 0x54, 0x04, 0x04, 0x0A, 0x20, 0x06, 0x00, 0x00, 0x00, 0x00, 0x00, 0x3F,
+0xFE, 0x54, 0x04, 0x1C, 0x60, 0x04, 0x06, 0x14, 0x10, 0x05, 0x00, 0x00, 0x00, 0x00, 0x00, 0x1F,
+0xFC, 0x28, 0x08, 0x2E, 0x50, 0x04, 0x04, 0x28, 0x08, 0x06, 0x07, 0xC0, 0x00, 0x01, 0xF0, 0x3F,
+0xFE, 0x14, 0x10, 0x54, 0x60, 0x04, 0x06, 0x54, 0x04, 0x04, 0x0A, 0x20, 0x00, 0x02, 0x08, 0x1F,
+0xFC, 0x0A, 0x20, 0x66, 0x54, 0x04, 0x1C, 0x60, 0x04, 0x06, 0x14, 0x10, 0x00, 0x05, 0x04, 0x3F,
+0xFE, 0x07, 0xC0, 0x54, 0x28, 0x08, 0x2E, 0x50, 0x04, 0x04, 0x28, 0x08, 0x00, 0x0A, 0x02, 0x1F,
+0xFC, 0x00, 0x00, 0x2E, 0x14, 0x10, 0x54, 0x60, 0x04, 0x06, 0x54, 0x04, 0x00, 0x15, 0x01, 0x3F,
+0xFE, 0x00, 0x00, 0x1C, 0x0A, 0x20, 0x66, 0x54, 0x04, 0x1C, 0x60, 0x04, 0x00, 0x18, 0x01, 0x1F,
+0xFC, 0x00, 0x00, 0x06, 0x07, 0xC0, 0x54, 0x28, 0x08, 0x2E, 0x50, 0x04, 0x00, 0x14, 0x01, 0x3F,
+0xFE, 0x00, 0x00, 0x04, 0x00, 0x00, 0x2E, 0x14, 0x10, 0x54, 0x60, 0x04, 0x00, 0x18, 0x01, 0x1F,
+0xFC, 0xFF, 0xFF, 0xFE, 0x00, 0x00, 0x1C, 0x0A, 0x20, 0x66, 0x54, 0x04, 0x1C, 0x15, 0x01, 0x3F,
+0xFE, 0xD5, 0x55, 0x54, 0x00, 0x00, 0x06, 0x07, 0xC0, 0x54, 0x28, 0x08, 0x2A, 0x0A, 0x02, 0x1F,
+0xFC, 0x84, 0x10, 0x46, 0x00, 0x00, 0x04, 0x00, 0x00, 0x2E, 0x14, 0x10, 0x51, 0x05, 0x04, 0x3F,
+0xFE, 0xC4, 0x10, 0x44, 0xFF, 0xFF, 0xFE, 0x00, 0x00, 0x1C, 0x0A, 0x20, 0x61, 0x02, 0x88, 0x1F,
+0xFC, 0x84, 0x10, 0x46, 0xD5, 0x55, 0x54, 0x00, 0x00, 0x06, 0x07, 0xC0, 0x51, 0x01, 0xF0, 0x3F,
+0xFE, 0x84, 0x10, 0x44, 0x84, 0x10, 0x46, 0x00, 0x00, 0x04, 0x00, 0x00, 0x2A, 0x00, 0x00, 0x1F,
+0xFC, 0xC4, 0x10, 0x46, 0xC4, 0x10, 0x44, 0xFF, 0xFF, 0xFE, 0x00, 0x00, 0x1C, 0x00, 0x00, 0x3F,
+0xFE, 0x84, 0x10, 0x44, 0x84, 0x10, 0x46, 0xD5, 0x55, 0x54, 0x00, 0x00, 0x00, 0x00, 0x00, 0x1F,
+0xFC, 0xD5, 0x55, 0x56, 0x84, 0x10, 0x44, 0x84, 0x10, 0x46, 0x00, 0x00, 0x00, 0x00, 0x00, 0x3F,
+0xFC, 0xFF, 0xFF, 0xFC, 0xC4, 0x10, 0x46, 0xC4, 0x10, 0x44, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0x9F,
+0xFE, 0x00, 0x00, 0x06, 0x84, 0x10, 0x44, 0x84, 0x10, 0x46, 0xD5, 0x55, 0x55, 0x55, 0x55, 0xBF,
+0xFD, 0x55, 0x55, 0x54, 0xD5, 0x55, 0x56, 0x84, 0x10, 0x44, 0x84, 0x10, 0x41, 0x04, 0x10, 0x9F,
+0xFF, 0xFF, 0xFF, 0xFC, 0xFF, 0xFF, 0xFC, 0xC4, 0x10, 0x46, 0xC4, 0x10, 0x41, 0x04, 0x11, 0xBF,
+0xFF, 0xFF, 0xFF, 0xFE, 0x00, 0x00, 0x06, 0x84, 0x10, 0x44, 0x84, 0x10, 0x41, 0x04, 0x10, 0x9F,
+0xFF, 0xFF, 0xFF, 0xFD, 0x55, 0x55, 0x54, 0xD5, 0x55, 0x56, 0x84, 0x10, 0x41, 0x04, 0x10, 0x9F,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFC, 0xFF, 0xFF, 0xFC, 0xC4, 0x10, 0x41, 0x04, 0x11, 0xBF,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFE, 0x00, 0x00, 0x06, 0x84, 0x10, 0x41, 0x04, 0x10, 0x9F,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFD, 0x55, 0x55, 0x54, 0xD5, 0x55, 0x55, 0x55, 0x55, 0xBF,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFC, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0x9F,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFE, 0x00, 0x00, 0x00, 0x00, 0x00, 0x3F,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFD, 0x55, 0x55, 0x55, 0x55, 0x55, 0x5F,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xE0, 0x2E, 0xFB, 0x7D, 0xFB, 0xFB, 0xCF, 0xC1, 0xDF, 0xBB, 0x3E, 0xC0, 0xE1, 0xFE, 0x3C, 0x1F,
+0xFD, 0xEE, 0x7B, 0x39, 0xF9, 0xF3, 0xCF, 0x9E, 0xDF, 0xBB, 0x3E, 0xDF, 0xDE, 0xFC, 0xDD, 0xE7,
+0xFD, 0xEE, 0x3B, 0xBB, 0xF9, 0xEB, 0xD7, 0xBF, 0x5F, 0xBB, 0x5E, 0xDF, 0xDE, 0xFD, 0xED, 0xF7,
+0xFD, 0xEE, 0xBB, 0xD3, 0xFA, 0xEB, 0xB7, 0x3F, 0xDF, 0xBB, 0x4E, 0xDF, 0xDF, 0xFF, 0xCD, 0xF3,
+0xFD, 0xEE, 0xDB, 0xC7, 0xFA, 0xEB, 0xBB, 0x7F, 0xC0, 0x3B, 0x6E, 0xC0, 0xE3, 0xFF, 0x1D, 0xF3,
+0xFD, 0xEE, 0xCB, 0xEF, 0xFA, 0xDB, 0xBB, 0x7F, 0xDF, 0xBB, 0x66, 0xDF, 0xF8, 0xFF, 0xCD, 0xF3,
+0xFD, 0xEE, 0xEB, 0xEF, 0xFB, 0x5B, 0x03, 0x3F, 0x5F, 0xBB, 0x76, 0xDF, 0xFE, 0x7F, 0xED, 0xF3,
+0xFD, 0xEE, 0xF3, 0xEF, 0xFB, 0x5B, 0x79, 0xBE, 0xDF, 0xBB, 0x7A, 0xDF, 0xDE, 0x7D, 0xED, 0xF7,
+0xFD, 0xEE, 0xF3, 0xEF, 0xFB, 0xBA, 0xFD, 0x9E, 0xDF, 0xBB, 0x7C, 0xDF, 0xDE, 0xFD, 0xCD, 0xE7,
+0xFD, 0xEE, 0xFB, 0xEF, 0xFB, 0xBA, 0xFD, 0xC1, 0xDF, 0xBB, 0x7E, 0xC0, 0xE0, 0xFE, 0x1C, 0x1F,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF,
+0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF
+};
+
+

Marlin/_Statusscreen.h

@@ -0,0 +1,472 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Custom Status Screen bitmap
+ *
+ * Place this file in the root with your configuration files
+ * and enable CUSTOM_STATUS_SCREEN_IMAGE in Configuration.h.
+ *
+ * Use the Marlin Bitmap Converter to make your own:
+ * http://marlinfw.org/tools/u8glib/converter.html
+ */
+#include "MarlinConfig.h"
+
+//============================================
+
+#define STATUS_SCREENWIDTH 128
+
+#define STATUS_SCREEN_HOTEND_TEXT_X(E) (41 + (E) * 20)
+
+#define STATUS_SCREEN_BED_TEXT_X (HOTENDS > 1 ? 81 : 73)
+
+#define FAN_ANIM_FRAMES 3
+#define STATUS_SCREEN_FAN_TEXT_X (FAN_ANIM_FRAMES == 3 ? 103 : 105)
+#define STATUS_SCREEN_FAN_TEXT_Y (FAN_ANIM_FRAMES > 2 ? 28 : 27)
+
+//============================================
+
+#if HOTENDS < 2
+
+  #if FAN_ANIM_FRAMES <= 2
+
+    const unsigned char status_screen0_bmp[] PROGMEM = {
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11111111,B11111000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111110,B00000000,B11111000,
+  B10001110,B00000000,B11100001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111000,B00111111,B00111000,
+  B10011111,B00000000,B11110001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110000,B01111110,B00011000,
+  B10010011,B10000001,B00111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110000,B01111100,B00011000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00101000,B01111100,B00001000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00101100,B00111000,B00001000,
+  B10011111,B10111001,B11110001,B00000000,B00000000,B00011111,B11100000,B00000000,B00000000,B00001000,B00100000,B10000000,B00000000,B00101111,B00111001,B11001000,
+  B10001111,B00101000,B11110001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00000100,B00010000,B01000000,B00000000,B00101111,B11111111,B11101000,
+  B10000000,B00111000,B00000001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00000100,B00010000,B01000000,B00000000,B00101111,B11000111,B11101000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00001000,B00100000,B10000000,B00000000,B00101111,B11111111,B11101000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00011111,B11100000,B00000000,B00000000,B00010000,B01000001,B00000000,B00000000,B00100111,B00111001,B11101000,
+  B10010001,B01110100,B10011001,B00000000,B00000000,B00011111,B11100000,B00000000,B00000000,B00100000,B10000010,B00000000,B00000000,B00100000,B00111000,B01101000,
+  B10011011,B00000110,B10101001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00100000,B10000010,B00000000,B00000000,B00100000,B01111100,B00101000,
+  B10011011,B01010100,B10101001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00010000,B01000001,B00000000,B00000000,B00110000,B01111100,B00011000,
+  B10011011,B01010110,B10101001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00001000,B00100000,B10000000,B00000000,B00110000,B11111100,B00011000,
+  B10011011,B01010100,B10011001,B00000000,B00000000,B00001111,B11000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111001,B11111000,B00111000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00000111,B10000000,B00000000,B00000000,B11111111,B11111111,B11000000,B00000000,B00111110,B00000000,B11111000,
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000011,B00000000,B00000000,B00000000,B11111111,B11111111,B11000000,B00000000,B00111111,B11111111,B11111000 
+};
+    const unsigned char status_screen1_bmp[] PROGMEM = {
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11111111,B11111000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111110,B10000000,B11111000,
+  B10001110,B00000000,B11100001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111001,B10000000,B00111000,
+  B10011111,B00000000,B11110001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110111,B10000001,B11011000,
+  B10010011,B10000001,B00111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110111,B11000011,B11011000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00100111,B11000111,B11101000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00100011,B11000111,B11111000,
+  B10011111,B10111001,B11110001,B00000000,B00000000,B00011111,B11100000,B00000000,B00000000,B00001000,B00100000,B10000000,B00000000,B00100001,B11111111,B10001000,
+  B10001111,B00101000,B11110001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00000100,B00010000,B01000000,B00000000,B00100000,B01101100,B00001000,
+  B10000000,B00111000,B00000001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00000100,B00010000,B01000000,B00000000,B00100000,B01101100,B00001000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00001000,B00100000,B10000000,B00000000,B00100000,B01101100,B00001000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00011111,B11100000,B00000000,B00000000,B00010000,B01000001,B00000000,B00000000,B00100011,B11111111,B00001000,
+  B10010001,B01110100,B10011001,B00000000,B00000000,B00011111,B11100000,B00000000,B00000000,B00100000,B10000010,B00000000,B00000000,B00111111,B11000111,B10001000,
+  B10011011,B00000110,B10101001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00100000,B10000010,B00000000,B00000000,B00101111,B11000111,B11001000,
+  B10011011,B01010100,B10101001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00010000,B01000001,B00000000,B00000000,B00110111,B10000111,B11011000,
+  B10011011,B01010110,B10101001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00001000,B00100000,B10000000,B00000000,B00110111,B00000011,B11011000,
+  B10011011,B01010100,B10011001,B00000000,B00000000,B00001111,B11000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111000,B00000011,B00111000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00000111,B10000000,B00000000,B00000000,B11111111,B11111111,B11000000,B00000000,B00111110,B00000010,B11111000,
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000011,B00000000,B00000000,B00000000,B11111111,B11111111,B11000000,B00000000,B00111111,B11111111,B11111000 
+};
+
+  #elif FAN_ANIM_FRAMES == 3
+
+
+const unsigned char status_screen0_bmp[] PROGMEM = {
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11111111,B11111000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111110,B00000000,B11111000,
+  B10001110,B00000000,B11100001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111000,B00111111,B00111000,
+  B10011111,B00000000,B11110001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110000,B01111110,B00011000,
+  B10010011,B10000001,B00111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110000,B01111100,B00011000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00101000,B01111100,B00001000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00101100,B00111000,B00001000,
+  B10011111,B10111001,B11110001,B00000000,B00000000,B00011111,B11100000,B00000000,B00000000,B00001000,B00100000,B10000000,B00000000,B00101111,B00111001,B11001000,
+  B10001111,B00101000,B11110001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00000100,B00010000,B01000000,B00000000,B00101111,B11111111,B11101000,
+  B10000000,B00111000,B00000001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00000100,B00010000,B01000000,B00000000,B00101111,B11000111,B11101000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00001000,B00100000,B10000000,B00000000,B00101111,B11111111,B11101000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00011111,B11100000,B00000000,B00000000,B00010000,B01000001,B00000000,B00000000,B00100111,B00111001,B11101000,
+  B10010001,B01110100,B10011001,B00000000,B00000000,B00011111,B11100000,B00000000,B00000000,B00100000,B10000010,B00000000,B00000000,B00100000,B00111000,B01101000,
+  B10011011,B00000110,B10101001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00100000,B10000010,B00000000,B00000000,B00100000,B01111100,B00101000,
+  B10011011,B01010100,B10101001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00010000,B01000001,B00000000,B00000000,B00110000,B01111100,B00011000,
+  B10011011,B01010110,B10101001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00001000,B00100000,B10000000,B00000000,B00110000,B11111100,B00011000,
+  B10011011,B01010100,B10011001,B00000000,B00000000,B00001111,B11000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111001,B11111000,B00111000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00000111,B10000000,B00000000,B00000000,B11111111,B11111111,B11000000,B00000000,B00111110,B00000000,B11111000,
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000011,B00000000,B00000000,B00000000,B11111111,B11111111,B11000000,B00000000,B00111111,B11111111,B11111000 
+};
+
+
+    const unsigned char status_screen1_bmp[] PROGMEM = {
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11111111,B11111000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111110,B00000000,B11111000,
+  B10001110,B00000000,B11100001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111000,B00001111,B00111000,
+  B10011111,B00000000,B11110001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110100,B00011111,B11011000,
+  B10010011,B10000001,B00111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110110,B00011111,B10011000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00101111,B00011111,B00001000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00101111,B10011110,B00001000,
+  B10011111,B10111001,B11110001,B00000000,B00000000,B00011111,B11100000,B00000000,B00000000,B00001000,B00100000,B10000000,B00000000,B00101111,B11111100,B00001000,
+  B10001111,B00101000,B11110001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00000100,B00010000,B01000000,B00000000,B00101111,B11011100,B00001000,
+  B10000000,B00111000,B00000001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00000100,B00010000,B01000000,B00000000,B00100111,B11101111,B11001000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00001000,B00100000,B10000000,B00000000,B00100000,B01110111,B11101000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00011111,B11100000,B00000000,B00000000,B00010000,B01000001,B00000000,B00000000,B00100000,B01111111,B11101000,
+  B10010001,B01110100,B10011001,B00000000,B00000000,B00011111,B11100000,B00000000,B00000000,B00100000,B10000010,B00000000,B00000000,B00100000,B11110011,B11101000,
+  B10011011,B00000110,B10101001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00100000,B10000010,B00000000,B00000000,B00100001,B11110001,B11101000,
+  B10011011,B01010100,B10101001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00010000,B01000001,B00000000,B00000000,B00110011,B11110000,B11011000,
+  B10011011,B01010110,B10101001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00001000,B00100000,B10000000,B00000000,B00110111,B11110000,B01011000,
+  B10011011,B01010100,B10011001,B00000000,B00000000,B00001111,B11000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111001,B11100000,B00111000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00000111,B10000000,B00000000,B00000000,B11111111,B11111111,B11000000,B00000000,B00111110,B00000000,B11111000,
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000011,B00000000,B00000000,B00000000,B11111111,B11111111,B11000000,B00000000,B00111111,B11111111,B11111000 
+};
+    const unsigned char status_screen2_bmp[] PROGMEM = {
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11111111,B11111000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111110,B10000000,B11111000,
+  B10001110,B00000000,B11100001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111001,B10000000,B00111000,
+  B10011111,B00000000,B11110001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110111,B10000001,B11011000,
+  B10010011,B10000001,B00111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110111,B11000011,B11011000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00100111,B11000111,B11101000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00100011,B11000111,B11111000,
+  B10011111,B10111001,B11110001,B00000000,B00000000,B00011111,B11100000,B00000000,B00000000,B00001000,B00100000,B10000000,B00000000,B00100001,B11111111,B10001000,
+  B10001111,B00101000,B11110001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00000100,B00010000,B01000000,B00000000,B00100000,B01101100,B00001000,
+  B10000000,B00111000,B00000001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00000100,B00010000,B01000000,B00000000,B00100000,B01101100,B00001000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00001000,B00100000,B10000000,B00000000,B00100000,B01101100,B00001000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00011111,B11100000,B00000000,B00000000,B00010000,B01000001,B00000000,B00000000,B00100011,B11111111,B00001000,
+  B10010001,B01110100,B10011001,B00000000,B00000000,B00011111,B11100000,B00000000,B00000000,B00100000,B10000010,B00000000,B00000000,B00111111,B11000111,B10001000,
+  B10011011,B00000110,B10101001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00100000,B10000010,B00000000,B00000000,B00101111,B11000111,B11001000,
+  B10011011,B01010100,B10101001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00010000,B01000001,B00000000,B00000000,B00110111,B10000111,B11011000,
+  B10011011,B01010110,B10101001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00001000,B00100000,B10000000,B00000000,B00110111,B00000011,B11011000,
+  B10011011,B01010100,B10011001,B00000000,B00000000,B00001111,B11000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111000,B00000011,B00111000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00000111,B10000000,B00000000,B00000000,B11111111,B11111111,B11000000,B00000000,B00111110,B00000010,B11111000,
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000011,B00000000,B00000000,B00000000,B11111111,B11111111,B11000000,B00000000,B00111111,B11111111,B11111000 
+};
+
+  #elif FAN_ANIM_FRAMES == 4
+
+const unsigned char status_screen0_bmp[] PROGMEM = {
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11111111,B11111000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111110,B00000000,B11111000,
+  B10001110,B00000000,B11100001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111000,B00111111,B00111000,
+  B10011111,B00000000,B11110001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110000,B01111110,B00011000,
+  B10010011,B10000001,B00111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110000,B01111100,B00011000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00101000,B01111100,B00001000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00101100,B00111000,B00001000,
+  B10011111,B10111001,B11110001,B00000000,B00000000,B00011111,B11100000,B00000000,B00000000,B00001000,B00100000,B10000000,B00000000,B00101111,B00111001,B11001000,
+  B10001111,B00101000,B11110001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00000100,B00010000,B01000000,B00000000,B00101111,B11111111,B11101000,
+  B10000000,B00111000,B00000001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00000100,B00010000,B01000000,B00000000,B00101111,B11000111,B11101000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00001000,B00100000,B10000000,B00000000,B00101111,B11111111,B11101000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00011111,B11100000,B00000000,B00000000,B00010000,B01000001,B00000000,B00000000,B00100111,B00111001,B11101000,
+  B10010001,B01110100,B10011001,B00000000,B00000000,B00011111,B11100000,B00000000,B00000000,B00100000,B10000010,B00000000,B00000000,B00100000,B00111000,B01101000,
+  B10011011,B00000110,B10101001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00100000,B10000010,B00000000,B00000000,B00100000,B01111100,B00101000,
+  B10011011,B01010100,B10101001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00010000,B01000001,B00000000,B00000000,B00110000,B01111100,B00011000,
+  B10011011,B01010110,B10101001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00001000,B00100000,B10000000,B00000000,B00110000,B11111100,B00011000,
+  B10011011,B01010100,B10011001,B00000000,B00000000,B00001111,B11000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111001,B11111000,B00111000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00000111,B10000000,B00000000,B00000000,B11111111,B11111111,B11000000,B00000000,B00111110,B00000000,B11111000,
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000011,B00000000,B00000000,B00000000,B11111111,B11111111,B11000000,B00000000,B00111111,B11111111,B11111000 
+};
+
+const unsigned char status_screen1_bmp[] PROGMEM = {
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11111111,B11111000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111110,B00000000,B11111000,
+  B10001110,B00000000,B11100001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111000,B00001111,B00111000,
+  B10011111,B00000000,B11110001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110100,B00011111,B11011000,
+  B10010011,B10000001,B00111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110110,B00011111,B10011000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00101111,B00011111,B00001000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00101111,B10011110,B00001000,
+  B10011111,B10111001,B11110001,B00000000,B00000000,B00011111,B11100000,B00000000,B00000000,B00001000,B00100000,B10000000,B00000000,B00101111,B11111100,B00001000,
+  B10001111,B00101000,B11110001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00000100,B00010000,B01000000,B00000000,B00101111,B11011100,B00001000,
+  B10000000,B00111000,B00000001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00000100,B00010000,B01000000,B00000000,B00100111,B11101111,B11001000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00001000,B00100000,B10000000,B00000000,B00100000,B01110111,B11101000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00011111,B11100000,B00000000,B00000000,B00010000,B01000001,B00000000,B00000000,B00100000,B01111111,B11101000,
+  B10010001,B01110100,B10011001,B00000000,B00000000,B00011111,B11100000,B00000000,B00000000,B00100000,B10000010,B00000000,B00000000,B00100000,B11110011,B11101000,
+  B10011011,B00000110,B10101001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00100000,B10000010,B00000000,B00000000,B00100001,B11110001,B11101000,
+  B10011011,B01010100,B10101001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00010000,B01000001,B00000000,B00000000,B00110011,B11110000,B11011000,
+  B10011011,B01010110,B10101001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00001000,B00100000,B10000000,B00000000,B00110111,B11110000,B01011000,
+  B10011011,B01010100,B10011001,B00000000,B00000000,B00001111,B11000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111001,B11100000,B00111000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00000111,B10000000,B00000000,B00000000,B11111111,B11111111,B11000000,B00000000,B00111110,B00000000,B11111000,
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000011,B00000000,B00000000,B00000000,B11111111,B11111111,B11000000,B00000000,B00111111,B11111111,B11111000 
+};
+
+const unsigned char status_screen2_bmp[] PROGMEM = {
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11111111,B11111000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111110,B10000000,B11111000,
+  B10001110,B00000000,B11100001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111001,B10000000,B00111000,
+  B10011111,B00000000,B11110001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110111,B10000001,B11011000,
+  B10010011,B10000001,B00111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110111,B11000011,B11011000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00100111,B11000111,B11101000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00100011,B11000111,B11111000,
+  B10011111,B10111001,B11110001,B00000000,B00000000,B00011111,B11100000,B00000000,B00000000,B00001000,B00100000,B10000000,B00000000,B00100001,B11111111,B10001000,
+  B10001111,B00101000,B11110001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00000100,B00010000,B01000000,B00000000,B00100000,B01101100,B00001000,
+  B10000000,B00111000,B00000001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00000100,B00010000,B01000000,B00000000,B00100000,B01101100,B00001000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00001000,B00100000,B10000000,B00000000,B00100000,B01101100,B00001000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00011111,B11100000,B00000000,B00000000,B00010000,B01000001,B00000000,B00000000,B00100011,B11111111,B00001000,
+  B10010001,B01110100,B10011001,B00000000,B00000000,B00011111,B11100000,B00000000,B00000000,B00100000,B10000010,B00000000,B00000000,B00111111,B11000111,B10001000,
+  B10011011,B00000110,B10101001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00100000,B10000010,B00000000,B00000000,B00101111,B11000111,B11001000,
+  B10011011,B01010100,B10101001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00010000,B01000001,B00000000,B00000000,B00110111,B10000111,B11011000,
+  B10011011,B01010110,B10101001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00001000,B00100000,B10000000,B00000000,B00110111,B00000011,B11011000,
+  B10011011,B01010100,B10011001,B00000000,B00000000,B00001111,B11000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111000,B00000011,B00111000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00000111,B10000000,B00000000,B00000000,B11111111,B11111111,B11000000,B00000000,B00111110,B00000010,B11111000,
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000011,B00000000,B00000000,B00000000,B11111111,B11111111,B11000000,B00000000,B00111111,B11111111,B11111000 
+};
+
+
+const unsigned char status_screen3_bmp[] PROGMEM = {
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11111111,B11111000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111110,B00000000,B11111000,
+  B10001110,B00000000,B11100001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111001,B11110000,B00111000,
+  B10011111,B00000000,B11110001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110001,B11100000,B00011000,
+  B10010011,B10000001,B00111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110001,B11100000,B00011000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00100001,B11100001,B11101000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00100000,B11110011,B11101000,
+  B10011111,B10111001,B11110001,B00000000,B00000000,B00011111,B11100000,B00000000,B00000000,B00001000,B00100000,B10000000,B00000000,B00100000,B01111111,B11101000,
+  B10001111,B00101000,B11110001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00000100,B00010000,B01000000,B00000000,B00100000,B01110111,B11101000,
+  B10000000,B00111000,B00000001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00000100,B00010000,B01000000,B00000000,B00101000,B11101110,B00101000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00001000,B00100000,B10000000,B00000000,B00101111,B11011100,B00001000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00011111,B11100000,B00000000,B00000000,B00010000,B01000001,B00000000,B00000000,B00101111,B11111100,B00001000,
+  B10010001,B01110100,B10011001,B00000000,B00000000,B00011111,B11100000,B00000000,B00000000,B00100000,B10000010,B00000000,B00000000,B00101111,B10011110,B00001000,
+  B10011011,B00000110,B10101001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00100000,B10000010,B00000000,B00000000,B00101111,B00001111,B00001000,
+  B10011011,B01010100,B10101001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00010000,B01000001,B00000000,B00000000,B00110000,B00001111,B00011000,
+  B10011011,B01010110,B10101001,B00000000,B00000000,B00111111,B11110000,B00000000,B00000000,B00001000,B00100000,B10000000,B00000000,B00110000,B00001111,B00011000,
+  B10011011,B01010100,B10011001,B00000000,B00000000,B00001111,B11000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111000,B00011111,B00111000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00000111,B10000000,B00000000,B00000000,B11111111,B11111111,B11000000,B00000000,B00111110,B00000000,B11111000,
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000011,B00000000,B00000000,B00000000,B11111111,B11111111,B11000000,B00000000,B00111111,B11111111,B11111000 
+};
+
+
+  #endif
+
+#else // HOTENDS >= 2
+
+  #if FAN_ANIM_FRAMES <= 2
+
+const unsigned char status_screen0_bmp[] PROGMEM = {
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11111111,B11111000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111110,B00000000,B11111000,
+  B10001110,B00000000,B11100001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111000,B00111111,B00111000,
+  B10011111,B00000000,B11110001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110000,B01111110,B00011000,
+  B10010011,B10000001,B00111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110000,B01111100,B00011000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00101000,B01111100,B00001000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00101100,B00111000,B00001000,
+  B10011111,B10111001,B11110001,B00000000,B00000000,B00011111,B11100000,B00000001,B11111110,B00000000,B00001000,B00100000,B10000000,B00101111,B00111001,B11001000,
+  B10001111,B00101000,B11110001,B00000000,B00000000,B00111110,B11110000,B00000011,B11001111,B00000000,B00000100,B00010000,B01000000,B00101111,B11111111,B11101000,
+  B10000000,B00111000,B00000001,B00000000,B00000000,B00111100,B11110000,B00000011,B10110111,B00000000,B00000100,B00010000,B01000000,B00101111,B11000111,B11101000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00111010,B11110000,B00000011,B11110111,B00000000,B00001000,B00100000,B10000000,B00101111,B11111111,B11101000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00011110,B11100000,B00000001,B11101110,B00000000,B00010000,B01000001,B00000000,B00100111,B00111001,B11101000,
+  B10010001,B01110100,B10011001,B00000000,B00000000,B00011110,B11100000,B00000001,B11011110,B00000000,B00100000,B10000010,B00000000,B00100000,B00111000,B01101000,
+  B10011011,B00000110,B10101001,B00000000,B00000000,B00111110,B11110000,B00000011,B10111111,B00000000,B00100000,B10000010,B00000000,B00100000,B01111100,B00101000,
+  B10011011,B01010100,B10101001,B00000000,B00000000,B00111110,B11110000,B00000011,B10000111,B00000000,B00010000,B01000001,B00000000,B00110000,B01111100,B00011000,
+  B10011011,B01010110,B10101001,B00000000,B00000000,B00111111,B11110000,B00000011,B11111111,B00000000,B00001000,B00100000,B10000000,B00110000,B11111100,B00011000,
+  B10011011,B01010100,B10011001,B00000000,B00000000,B00001111,B11000000,B00000000,B11111100,B00000000,B00000000,B00000000,B00000000,B00111001,B11111000,B00111000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00000111,B10000000,B00000000,B01111000,B00000000,B11111111,B11111111,B11000000,B00111110,B00000000,B11111000,
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000011,B00000000,B00000000,B00110000,B00000000,B11111111,B11111111,B11000000,B00111111,B11111111,B11111000 
+};
+
+
+const unsigned char status_screen1_bmp[] PROGMEM = {
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11111111,B11111000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111110,B00000000,B11111000,
+  B10001110,B00000000,B11100001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111000,B00001111,B00111000,
+  B10011111,B00000000,B11110001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110100,B00011111,B11011000,
+  B10010011,B10000001,B00111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110110,B00011111,B10011000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00101111,B00011111,B00001000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00101111,B10011110,B00001000,
+  B10011111,B10111001,B11110001,B00000000,B00000000,B00011111,B11100000,B00000001,B11111110,B00000000,B00001000,B00100000,B10000000,B00101111,B11111100,B00001000,
+  B10001111,B00101000,B11110001,B00000000,B00000000,B00111110,B11110000,B00000011,B11001111,B00000000,B00000100,B00010000,B01000000,B00101111,B11011100,B00001000,
+  B10000000,B00111000,B00000001,B00000000,B00000000,B00111100,B11110000,B00000011,B10110111,B00000000,B00000100,B00010000,B01000000,B00100111,B11101111,B11001000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00111010,B11110000,B00000011,B11110111,B00000000,B00001000,B00100000,B10000000,B00100000,B01110111,B11101000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00011110,B11100000,B00000001,B11101110,B00000000,B00010000,B01000001,B00000000,B00100000,B01111111,B11101000,
+  B10010001,B01110100,B10011001,B00000000,B00000000,B00011110,B11100000,B00000001,B11011110,B00000000,B00100000,B10000010,B00000000,B00100000,B11110011,B11101000,
+  B10011011,B00000110,B10101001,B00000000,B00000000,B00111110,B11110000,B00000011,B10111111,B00000000,B00100000,B10000010,B00000000,B00100001,B11110001,B11101000,
+  B10011011,B01010100,B10101001,B00000000,B00000000,B00111110,B11110000,B00000011,B10000111,B00000000,B00010000,B01000001,B00000000,B00110011,B11110000,B11011000,
+  B10011011,B01010110,B10101001,B00000000,B00000000,B00111111,B11110000,B00000011,B11111111,B00000000,B00001000,B00100000,B10000000,B00110111,B11110000,B01011000,
+  B10011011,B01010100,B10011001,B00000000,B00000000,B00001111,B11000000,B00000000,B11111100,B00000000,B00000000,B00000000,B00000000,B00111001,B11100000,B00111000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00000111,B10000000,B00000000,B01111000,B00000000,B11111111,B11111111,B11000000,B00111110,B00000000,B11111000,
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000011,B00000000,B00000000,B00110000,B00000000,B11111111,B11111111,B11000000,B00111111,B11111111,B11111000 
+};
+
+   
+  #elif FAN_ANIM_FRAMES == 3
+
+    const unsigned char status_screen0_bmp[] PROGMEM = {
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11111111,B11111000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111110,B00000000,B11111000,
+  B10001110,B00000000,B11100001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111000,B00111111,B00111000,
+  B10011111,B00000000,B11110001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110000,B01111110,B00011000,
+  B10010011,B10000001,B00111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110000,B01111100,B00011000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00101000,B01111100,B00001000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00101100,B00111000,B00001000,
+  B10011111,B10111001,B11110001,B00000000,B00000000,B00011111,B11100000,B00000001,B11111110,B00000000,B00001000,B00100000,B10000000,B00101111,B00111001,B11001000,
+  B10001111,B00101000,B11110001,B00000000,B00000000,B00111110,B11110000,B00000011,B11001111,B00000000,B00000100,B00010000,B01000000,B00101111,B11111111,B11101000,
+  B10000000,B00111000,B00000001,B00000000,B00000000,B00111100,B11110000,B00000011,B10110111,B00000000,B00000100,B00010000,B01000000,B00101111,B11000111,B11101000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00111010,B11110000,B00000011,B11110111,B00000000,B00001000,B00100000,B10000000,B00101111,B11111111,B11101000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00011110,B11100000,B00000001,B11101110,B00000000,B00010000,B01000001,B00000000,B00100111,B00111001,B11101000,
+  B10010001,B01110100,B10011001,B00000000,B00000000,B00011110,B11100000,B00000001,B11011110,B00000000,B00100000,B10000010,B00000000,B00100000,B00111000,B01101000,
+  B10011011,B00000110,B10101001,B00000000,B00000000,B00111110,B11110000,B00000011,B10111111,B00000000,B00100000,B10000010,B00000000,B00100000,B01111100,B00101000,
+  B10011011,B01010100,B10101001,B00000000,B00000000,B00111110,B11110000,B00000011,B10000111,B00000000,B00010000,B01000001,B00000000,B00110000,B01111100,B00011000,
+  B10011011,B01010110,B10101001,B00000000,B00000000,B00111111,B11110000,B00000011,B11111111,B00000000,B00001000,B00100000,B10000000,B00110000,B11111100,B00011000,
+  B10011011,B01010100,B10011001,B00000000,B00000000,B00001111,B11000000,B00000000,B11111100,B00000000,B00000000,B00000000,B00000000,B00111001,B11111000,B00111000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00000111,B10000000,B00000000,B01111000,B00000000,B11111111,B11111111,B11000000,B00111110,B00000000,B11111000,
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000011,B00000000,B00000000,B00110000,B00000000,B11111111,B11111111,B11000000,B00111111,B11111111,B11111000 
+};
+
+
+const unsigned char status_screen1_bmp[] PROGMEM = {
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11111111,B11111000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111110,B00000000,B11111000,
+  B10001110,B00000000,B11100001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111000,B00001111,B00111000,
+  B10011111,B00000000,B11110001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110100,B00011111,B11011000,
+  B10010011,B10000001,B00111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110110,B00011111,B10011000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00101111,B00011111,B00001000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00101111,B10011110,B00001000,
+  B10011111,B10111001,B11110001,B00000000,B00000000,B00011111,B11100000,B00000001,B11111110,B00000000,B00001000,B00100000,B10000000,B00101111,B11111100,B00001000,
+  B10001111,B00101000,B11110001,B00000000,B00000000,B00111110,B11110000,B00000011,B11001111,B00000000,B00000100,B00010000,B01000000,B00101111,B11011100,B00001000,
+  B10000000,B00111000,B00000001,B00000000,B00000000,B00111100,B11110000,B00000011,B10110111,B00000000,B00000100,B00010000,B01000000,B00100111,B11101111,B11001000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00111010,B11110000,B00000011,B11110111,B00000000,B00001000,B00100000,B10000000,B00100000,B01110111,B11101000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00011110,B11100000,B00000001,B11101110,B00000000,B00010000,B01000001,B00000000,B00100000,B01111111,B11101000,
+  B10010001,B01110100,B10011001,B00000000,B00000000,B00011110,B11100000,B00000001,B11011110,B00000000,B00100000,B10000010,B00000000,B00100000,B11110011,B11101000,
+  B10011011,B00000110,B10101001,B00000000,B00000000,B00111110,B11110000,B00000011,B10111111,B00000000,B00100000,B10000010,B00000000,B00100001,B11110001,B11101000,
+  B10011011,B01010100,B10101001,B00000000,B00000000,B00111110,B11110000,B00000011,B10000111,B00000000,B00010000,B01000001,B00000000,B00110011,B11110000,B11011000,
+  B10011011,B01010110,B10101001,B00000000,B00000000,B00111111,B11110000,B00000011,B11111111,B00000000,B00001000,B00100000,B10000000,B00110111,B11110000,B01011000,
+  B10011011,B01010100,B10011001,B00000000,B00000000,B00001111,B11000000,B00000000,B11111100,B00000000,B00000000,B00000000,B00000000,B00111001,B11100000,B00111000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00000111,B10000000,B00000000,B01111000,B00000000,B11111111,B11111111,B11000000,B00111110,B00000000,B11111000,
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000011,B00000000,B00000000,B00110000,B00000000,B11111111,B11111111,B11000000,B00111111,B11111111,B11111000 
+};
+
+const unsigned char status_screen2_bmp[] PROGMEM = {
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11111111,B11111000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111110,B10000000,B11111000,
+  B10001110,B00000000,B11100001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111001,B10000000,B00111000,
+  B10011111,B00000000,B11110001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110111,B10000001,B11011000,
+  B10010011,B10000001,B00111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110111,B11000011,B11011000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00100111,B11000111,B11101000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00100011,B11000111,B11111000,
+  B10011111,B10111001,B11110001,B00000000,B00000000,B00011111,B11100000,B00000001,B11111110,B00000000,B00001000,B00100000,B10000000,B00100001,B11111111,B10001000,
+  B10001111,B00101000,B11110001,B00000000,B00000000,B00111110,B11110000,B00000011,B11001111,B00000000,B00000100,B00010000,B01000000,B00100000,B01101100,B00001000,
+  B10000000,B00111000,B00000001,B00000000,B00000000,B00111100,B11110000,B00000011,B10110111,B00000000,B00000100,B00010000,B01000000,B00100000,B01101100,B00001000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00111010,B11110000,B00000011,B11110111,B00000000,B00001000,B00100000,B10000000,B00100000,B01101100,B00001000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00011110,B11100000,B00000001,B11101110,B00000000,B00010000,B01000001,B00000000,B00100011,B11111111,B00001000,
+  B10010001,B01110100,B10011001,B00000000,B00000000,B00011110,B11100000,B00000001,B11011110,B00000000,B00100000,B10000010,B00000000,B00111111,B11000111,B10001000,
+  B10011011,B00000110,B10101001,B00000000,B00000000,B00111110,B11110000,B00000011,B10111111,B00000000,B00100000,B10000010,B00000000,B00101111,B11000111,B11001000,
+  B10011011,B01010100,B10101001,B00000000,B00000000,B00111110,B11110000,B00000011,B10000111,B00000000,B00010000,B01000001,B00000000,B00110111,B10000111,B11011000,
+  B10011011,B01010110,B10101001,B00000000,B00000000,B00111111,B11110000,B00000011,B11111111,B00000000,B00001000,B00100000,B10000000,B00110111,B00000011,B11011000,
+  B10011011,B01010100,B10011001,B00000000,B00000000,B00001111,B11000000,B00000000,B11111100,B00000000,B00000000,B00000000,B00000000,B00111000,B00000011,B00111000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00000111,B10000000,B00000000,B01111000,B00000000,B11111111,B11111111,B11000000,B00111110,B00000010,B11111000,
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000011,B00000000,B00000000,B00110000,B00000000,B11111111,B11111111,B11000000,B00111111,B11111111,B11111000 
+};
+
+
+  #elif FAN_ANIM_FRAMES == 4
+
+    const unsigned char status_screen0_bmp[] PROGMEM = {
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11111111,B11111000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111110,B00000000,B11111000,
+  B10001110,B00000000,B11100001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111000,B00111111,B00111000,
+  B10011111,B00000000,B11110001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110000,B01111110,B00011000,
+  B10010011,B10000001,B00111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110000,B01111100,B00011000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00101000,B01111100,B00001000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00101100,B00111000,B00001000,
+  B10011111,B10111001,B11110001,B00000000,B00000000,B00011111,B11100000,B00000001,B11111110,B00000000,B00001000,B00100000,B10000000,B00101111,B00111001,B11001000,
+  B10001111,B00101000,B11110001,B00000000,B00000000,B00111110,B11110000,B00000011,B11001111,B00000000,B00000100,B00010000,B01000000,B00101111,B11111111,B11101000,
+  B10000000,B00111000,B00000001,B00000000,B00000000,B00111100,B11110000,B00000011,B10110111,B00000000,B00000100,B00010000,B01000000,B00101111,B11000111,B11101000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00111010,B11110000,B00000011,B11110111,B00000000,B00001000,B00100000,B10000000,B00101111,B11111111,B11101000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00011110,B11100000,B00000001,B11101110,B00000000,B00010000,B01000001,B00000000,B00100111,B00111001,B11101000,
+  B10010001,B01110100,B10011001,B00000000,B00000000,B00011110,B11100000,B00000001,B11011110,B00000000,B00100000,B10000010,B00000000,B00100000,B00111000,B01101000,
+  B10011011,B00000110,B10101001,B00000000,B00000000,B00111110,B11110000,B00000011,B10111111,B00000000,B00100000,B10000010,B00000000,B00100000,B01111100,B00101000,
+  B10011011,B01010100,B10101001,B00000000,B00000000,B00111110,B11110000,B00000011,B10000111,B00000000,B00010000,B01000001,B00000000,B00110000,B01111100,B00011000,
+  B10011011,B01010110,B10101001,B00000000,B00000000,B00111111,B11110000,B00000011,B11111111,B00000000,B00001000,B00100000,B10000000,B00110000,B11111100,B00011000,
+  B10011011,B01010100,B10011001,B00000000,B00000000,B00001111,B11000000,B00000000,B11111100,B00000000,B00000000,B00000000,B00000000,B00111001,B11111000,B00111000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00000111,B10000000,B00000000,B01111000,B00000000,B11111111,B11111111,B11000000,B00111110,B00000000,B11111000,
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000011,B00000000,B00000000,B00110000,B00000000,B11111111,B11111111,B11000000,B00111111,B11111111,B11111000 
+};
+
+
+const unsigned char status_screen1_bmp[] PROGMEM = {
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11111111,B11111000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111110,B00000000,B11111000,
+  B10001110,B00000000,B11100001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111000,B00001111,B00111000,
+  B10011111,B00000000,B11110001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110100,B00011111,B11011000,
+  B10010011,B10000001,B00111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110110,B00011111,B10011000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00101111,B00011111,B00001000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00101111,B10011110,B00001000,
+  B10011111,B10111001,B11110001,B00000000,B00000000,B00011111,B11100000,B00000001,B11111110,B00000000,B00001000,B00100000,B10000000,B00101111,B11111100,B00001000,
+  B10001111,B00101000,B11110001,B00000000,B00000000,B00111110,B11110000,B00000011,B11001111,B00000000,B00000100,B00010000,B01000000,B00101111,B11011100,B00001000,
+  B10000000,B00111000,B00000001,B00000000,B00000000,B00111100,B11110000,B00000011,B10110111,B00000000,B00000100,B00010000,B01000000,B00100111,B11101111,B11001000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00111010,B11110000,B00000011,B11110111,B00000000,B00001000,B00100000,B10000000,B00100000,B01110111,B11101000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00011110,B11100000,B00000001,B11101110,B00000000,B00010000,B01000001,B00000000,B00100000,B01111111,B11101000,
+  B10010001,B01110100,B10011001,B00000000,B00000000,B00011110,B11100000,B00000001,B11011110,B00000000,B00100000,B10000010,B00000000,B00100000,B11110011,B11101000,
+  B10011011,B00000110,B10101001,B00000000,B00000000,B00111110,B11110000,B00000011,B10111111,B00000000,B00100000,B10000010,B00000000,B00100001,B11110001,B11101000,
+  B10011011,B01010100,B10101001,B00000000,B00000000,B00111110,B11110000,B00000011,B10000111,B00000000,B00010000,B01000001,B00000000,B00110011,B11110000,B11011000,
+  B10011011,B01010110,B10101001,B00000000,B00000000,B00111111,B11110000,B00000011,B11111111,B00000000,B00001000,B00100000,B10000000,B00110111,B11110000,B01011000,
+  B10011011,B01010100,B10011001,B00000000,B00000000,B00001111,B11000000,B00000000,B11111100,B00000000,B00000000,B00000000,B00000000,B00111001,B11100000,B00111000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00000111,B10000000,B00000000,B01111000,B00000000,B11111111,B11111111,B11000000,B00111110,B00000000,B11111000,
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000011,B00000000,B00000000,B00110000,B00000000,B11111111,B11111111,B11000000,B00111111,B11111111,B11111000 
+};
+
+const unsigned char status_screen2_bmp[] PROGMEM = {
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11111111,B11111000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111110,B10000000,B11111000,
+  B10001110,B00000000,B11100001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111001,B10000000,B00111000,
+  B10011111,B00000000,B11110001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110111,B10000001,B11011000,
+  B10010011,B10000001,B00111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110111,B11000011,B11011000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00100111,B11000111,B11101000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00100011,B11000111,B11111000,
+  B10011111,B10111001,B11110001,B00000000,B00000000,B00011111,B11100000,B00000001,B11111110,B00000000,B00001000,B00100000,B10000000,B00100001,B11111111,B10001000,
+  B10001111,B00101000,B11110001,B00000000,B00000000,B00111110,B11110000,B00000011,B11001111,B00000000,B00000100,B00010000,B01000000,B00100000,B01101100,B00001000,
+  B10000000,B00111000,B00000001,B00000000,B00000000,B00111100,B11110000,B00000011,B10110111,B00000000,B00000100,B00010000,B01000000,B00100000,B01101100,B00001000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00111010,B11110000,B00000011,B11110111,B00000000,B00001000,B00100000,B10000000,B00100000,B01101100,B00001000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00011110,B11100000,B00000001,B11101110,B00000000,B00010000,B01000001,B00000000,B00100011,B11111111,B00001000,
+  B10010001,B01110100,B10011001,B00000000,B00000000,B00011110,B11100000,B00000001,B11011110,B00000000,B00100000,B10000010,B00000000,B00111111,B11000111,B10001000,
+  B10011011,B00000110,B10101001,B00000000,B00000000,B00111110,B11110000,B00000011,B10111111,B00000000,B00100000,B10000010,B00000000,B00101111,B11000111,B11001000,
+  B10011011,B01010100,B10101001,B00000000,B00000000,B00111110,B11110000,B00000011,B10000111,B00000000,B00010000,B01000001,B00000000,B00110111,B10000111,B11011000,
+  B10011011,B01010110,B10101001,B00000000,B00000000,B00111111,B11110000,B00000011,B11111111,B00000000,B00001000,B00100000,B10000000,B00110111,B00000011,B11011000,
+  B10011011,B01010100,B10011001,B00000000,B00000000,B00001111,B11000000,B00000000,B11111100,B00000000,B00000000,B00000000,B00000000,B00111000,B00000011,B00111000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00000111,B10000000,B00000000,B01111000,B00000000,B11111111,B11111111,B11000000,B00111110,B00000010,B11111000,
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000011,B00000000,B00000000,B00110000,B00000000,B11111111,B11111111,B11000000,B00111111,B11111111,B11111000 
+};
+
+const unsigned char status_screen3_bmp[] PROGMEM = {
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111111,B11111111,B11111000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111110,B00000000,B11111000,
+  B10001110,B00000000,B11100001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00111001,B11110000,B00111000,
+  B10011111,B00000000,B11110001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110001,B11100000,B00011000,
+  B10010011,B10000001,B00111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00110001,B11100000,B00011000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00100001,B11100001,B11101000,
+  B10011111,B10000001,B11111001,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00000000,B00100000,B11110011,B11101000,
+  B10011111,B10111001,B11110001,B00000000,B00000000,B00011111,B11100000,B00000001,B11111110,B00000000,B00001000,B00100000,B10000000,B00100000,B01111111,B11101000,
+  B10001111,B00101000,B11110001,B00000000,B00000000,B00111110,B11110000,B00000011,B11001111,B00000000,B00000100,B00010000,B01000000,B00100000,B01110111,B11101000,
+  B10000000,B00111000,B00000001,B00000000,B00000000,B00111100,B11110000,B00000011,B10110111,B00000000,B00000100,B00010000,B01000000,B00101000,B11101110,B00101000,
+  B10000000,B00000000,B00000001,B00000000,B00000000,B00111010,B11110000,B00000011,B11110111,B00000000,B00001000,B00100000,B10000000,B00101111,B11011100,B00001000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00011110,B11100000,B00000001,B11101110,B00000000,B00010000,B01000001,B00000000,B00101111,B11111100,B00001000,
+  B10010001,B01110100,B10011001,B00000000,B00000000,B00011110,B11100000,B00000001,B11011110,B00000000,B00100000,B10000010,B00000000,B00101111,B10011110,B00001000,
+  B10011011,B00000110,B10101001,B00000000,B00000000,B00111110,B11110000,B00000011,B10111111,B00000000,B00100000,B10000010,B00000000,B00101111,B00001111,B00001000,
+  B10011011,B01010100,B10101001,B00000000,B00000000,B00111110,B11110000,B00000011,B10000111,B00000000,B00010000,B01000001,B00000000,B00110000,B00001111,B00011000,
+  B10011011,B01010110,B10101001,B00000000,B00000000,B00111111,B11110000,B00000011,B11111111,B00000000,B00001000,B00100000,B10000000,B00110000,B00001111,B00011000,
+  B10011011,B01010100,B10011001,B00000000,B00000000,B00001111,B11000000,B00000000,B11111100,B00000000,B00000000,B00000000,B00000000,B00111000,B00011111,B00111000,
+  B10011111,B11111111,B11111001,B00000000,B00000000,B00000111,B10000000,B00000000,B01111000,B00000000,B11111111,B11111111,B11000000,B00111110,B00000000,B11111000,
+  B11111111,B11111111,B11111111,B00000000,B00000000,B00000011,B00000000,B00000000,B00110000,B00000000,B11111111,B11111111,B11000000,B00111111,B11111111,B11111000 
+};
+
+
+  #endif
+
+#endif // HOTENDS >= 2

Marlin/boards.h

@@ -74,6 +74,8 @@
 #define BOARD_AZTEEG_X3_PRO     68    // Azteeg X3 Pro
 #define BOARD_ULTIMAIN_2        72    // Ultimainboard 2.x (Uses TEMP_SENSOR 20)
 #define BOARD_RUMBA             80    // Rumba
+#define BOARD_FORMBOT_TREX2PLUS 95    // Formbot T-Rex 2 Plus
+#define BOARD_FORMBOT_TREX3     96    // Formbot T-Rex 3
 #define BOARD_BQ_ZUM_MEGA_3D    503   // bq ZUM Mega 3D
 #define BOARD_MAKEBOARD_MINI    431   // MakeBoard Mini v2.1.2 is a control board sold by MicroMake
 #define BOARD_TRIGORILLA_13     343   // TriGorilla Anycubic version 1.3 based on RAMPS EFB

Marlin/enum.h

@@ -157,10 +157,11 @@ enum LCDViewAction : char {
  * Dual X Carriage modes. A Dual Nozzle can also do duplication.
  */
 #if ENABLED(DUAL_X_CARRIAGE) || ENABLED(DUAL_NOZZLE_DUPLICATION_MODE)
-  enum DualXMode : char {
-    DXC_FULL_CONTROL_MODE,  // DUAL_X_CARRIAGE only
-    DXC_AUTO_PARK_MODE,     // DUAL_X_CARRIAGE only
-    DXC_DUPLICATION_MODE
+enum DualXMode : char {
+    DXC_FULL_CONTROL_MODE,
+    DXC_AUTO_PARK_MODE,
+    DXC_DUPLICATION_MODE,
+    DXC_MIRRORED_MODE
   };
 #endif
 

Marlin/example_configurations/AlephObjects/TAZ4/Configuration.h

@@ -743,7 +743,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/AliExpress/CL-260/Configuration.h

@@ -723,7 +723,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/Anet/A2plus/Configuration.h

@@ -762,7 +762,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/Anet/A6/Configuration.h

@@ -771,7 +771,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/Anet/A8/Configuration.h

@@ -736,7 +736,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/BIBO/TouchX/Cyclops/Configuration.h

@@ -723,7 +723,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/BIBO/TouchX/default/Configuration.h

@@ -723,7 +723,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/BQ/Hephestos/Configuration.h

@@ -711,7 +711,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/BQ/Hephestos_2/Configuration.h

@@ -724,7 +724,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/BQ/WITBOX/Configuration.h

@@ -711,7 +711,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/Cartesio/Configuration.h

@@ -722,7 +722,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/Creality/CR-10/Configuration.h

@@ -733,7 +733,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/Creality/CR-10S/Configuration.h

@@ -727,7 +727,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/Creality/CR-10mini/Configuration.h

@@ -742,7 +742,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/Creality/CR-8/Configuration.h

@@ -733,7 +733,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/Creality/Ender-2/Configuration.h

@@ -727,7 +727,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/Creality/Ender-3/Configuration.h

@@ -727,7 +727,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/Creality/Ender-4/Configuration.h

@@ -733,7 +733,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/Felix/Configuration.h

@@ -705,7 +705,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/Felix/DUAL/Configuration.h

@@ -705,7 +705,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/FolgerTech/i3-2020/Configuration.h

@@ -729,7 +729,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/Geeetech/GT2560/Configuration.h

@@ -738,7 +738,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/Geeetech/I3_Pro_X-GT2560/Configuration.h

@@ -723,7 +723,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   #define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/Geeetech/Prusa i3 Pro B/bltouch/Configuration.h

@@ -739,7 +739,17 @@
 #define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/Geeetech/Prusa i3 Pro B/noprobe/Configuration.h

@@ -738,7 +738,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/Geeetech/Prusa i3 Pro C/Configuration.h

@@ -723,7 +723,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/Geeetech/Prusa i3 Pro W/Configuration.h

@@ -723,7 +723,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/Infitary/i3-M508/Configuration.h

@@ -727,7 +727,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/JGAurora/A5/Configuration.h

@@ -735,7 +735,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/Malyan/M150/Configuration.h

@@ -743,7 +743,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/Micromake/C1/basic/Configuration.h

@@ -727,7 +727,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/Micromake/C1/enhanced/Configuration.h

@@ -727,7 +727,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/RepRapPro/Huxley/Configuration.h

@@ -763,7 +763,17 @@ Black rubber belt(MXL), 18 - tooth aluminium pulley : 87.489 step per mm (Huxley
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/RepRapWorld/Megatronics/Configuration.h

@@ -723,7 +723,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/RigidBot/Configuration.h

@@ -721,7 +721,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/SCARA/Configuration.h

@@ -736,7 +736,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/Sanguinololu/Configuration.h

@@ -754,7 +754,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/TinyBoy2/Configuration.h

@@ -774,7 +774,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/Tronxy/X1/Configuration.h

@@ -723,7 +723,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/Tronxy/X3A/Configuration.h

@@ -723,7 +723,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/Tronxy/X5S/Configuration.h

@@ -723,7 +723,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/Tronxy/XY100/Configuration.h

@@ -734,7 +734,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/Velleman/K8200/Configuration.h

@@ -752,7 +752,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/Velleman/K8400/Configuration.h

@@ -723,7 +723,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/Velleman/K8400/Dual-head/Configuration.h

@@ -723,7 +723,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/Wanhao/Duplicator 6/Configuration.h

@@ -733,7 +733,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/adafruit/ST7565/Configuration.h

@@ -723,7 +723,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/delta/Anycubic/Kossel/Configuration.h

@@ -862,7 +862,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/delta/FLSUN/auto_calibrate/Configuration.h

@@ -808,7 +808,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/delta/FLSUN/kossel/Configuration.h

@@ -808,7 +808,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/delta/FLSUN/kossel_mini/Configuration.h

@@ -808,7 +808,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/delta/Hatchbox_Alpha/Configuration.h

@@ -813,7 +813,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/delta/generic/Configuration.h

@@ -798,7 +798,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/delta/kossel_mini/Configuration.h

@@ -798,7 +798,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/delta/kossel_pro/Configuration.h

@@ -791,7 +791,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/delta/kossel_xl/Configuration.h

@@ -801,7 +801,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/gCreate/gMax1.5+/Configuration.h

@@ -736,7 +736,17 @@
 #define BLTOUCH
 #if ENABLED(BLTOUCH)
   #define BLTOUCH_DELAY 500   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/hangprinter/Configuration.h

@@ -861,7 +861,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/makibox/Configuration.h

@@ -726,7 +726,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/tvrrug/Round2/Configuration.h

@@ -718,7 +718,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/example_configurations/wt150/Configuration.h

@@ -728,7 +728,17 @@
 //#define BLTOUCH
 #if ENABLED(BLTOUCH)
   //#define BLTOUCH_DELAY 375   // (ms) Enable and increase if needed
+  
+  /**
+   * BLTouch V3.0 and newer smart series
+   * For genuine BLTouch 3.0 sensors. Clones may be confused by 3.0 command angles. YMMV.
+   * If the pin trigger is not detected, first try swapping the black and white wires then toggle this.
+   */
   //#define BLTOUCH_V3
+  #if ENABLED(BLTOUCH_V3)
+    //#define BLTOUCH_FORCE_5V_MODE
+    //#define BLTOUCH_FORCE_OPEN_DRAIN_MODE
+  #endif
 #endif
 
 /**

Marlin/language_en.h

@@ -184,6 +184,33 @@
 #ifndef MSG_USER_MENU
   #define MSG_USER_MENU                       _UxGT("Custom Commands")
 #endif
+#ifndef MSG_IDEX_MENU
+  #define MSG_IDEX_MENU                       _UxGT("IDEX Mode")
+#endif
+#ifndef MSG_IDEX_MODE_AUTOPARK
+  #define MSG_IDEX_MODE_AUTOPARK              _UxGT("Auto-Park")
+#endif
+#ifndef MSG_IDEX_MODE_DUPLICATE
+  #define MSG_IDEX_MODE_DUPLICATE             _UxGT("Duplication")
+#endif
+#ifndef MSG_IDEX_MODE_SCALED_COPY
+  #define MSG_IDEX_MODE_SCALED_COPY           _UxGT("Mirror")
+#endif
+#ifndef MSG_IDEX_MODE_FULL_CTRL
+  #define MSG_IDEX_MODE_FULL_CTRL             _UxGT("Full control")
+#endif
+#ifndef MSG_IDEX_X_OFFSET
+  #define MSG_IDEX_X_OFFSET                   _UxGT("2nd nozzle X")
+#endif
+#ifndef MSG_IDEX_Y_OFFSET
+  #define MSG_IDEX_Y_OFFSET                   _UxGT("2nd nozzle Y")
+#endif
+#ifndef MSG_IDEX_Z_OFFSET
+  #define MSG_IDEX_Z_OFFSET                   _UxGT("2nd nozzle Z")
+#endif
+#ifndef MSG_IDEX_SAVE_OFFSETS
+  #define MSG_IDEX_SAVE_OFFSETS               _UxGT("Save Offsets")
+#endif
 #ifndef MSG_UBL_DOING_G29
   #define MSG_UBL_DOING_G29                   _UxGT("Doing G29")
 #endif
@@ -756,6 +783,15 @@
 #ifndef MSG_BLTOUCH
   #define MSG_BLTOUCH                         _UxGT("BLTouch")
 #endif
+#ifndef MSG_BLTOUCH_SW_MODE
+  #define MSG_BLTOUCH_SW_MODE                 _UxGT("SW Deploy BLTouch")
+#endif
+#ifndef MSG_BLTOUCH_5V_MODE
+  #define MSG_BLTOUCH_5V_MODE                 _UxGT("BLTouch 5V Mode")
+#endif
+#ifndef MSG_BLTOUCH_OD_MODE
+  #define MSG_BLTOUCH_OD_MODE                 _UxGT("BLTouch OD Mode")
+#endif
 #ifndef MSG_BLTOUCH_SELFTEST
   #define MSG_BLTOUCH_SELFTEST                _UxGT("BLTouch Self-Test")
 #endif
@@ -1008,6 +1044,13 @@
 #ifndef MSG_M600_TOO_COLD
   #define MSG_M600_TOO_COLD                   _UxGT("M600: Too cold")
 #endif
+#ifndef MSG_LASER_ON
+    #define MSG_LASER_ON _UxGT("Laser on")
+#endif
+
+#ifndef MSG_LASER_OFF
+    #define MSG_LASER_OFF _UxGT("Laser off")
+#endif
 
 //
 // Filament Change screens show up to 3 lines on a 4-line display

Marlin/pins.h

@@ -128,6 +128,10 @@
   #include "pins_AZTEEG_X3_PRO.h"     // ATmega2560                                 env:megaatmega2560
 #elif MB(ULTIMAIN_2)
   #include "pins_ULTIMAIN_2.h"        // ATmega2560                                 env:megaatmega2560
+#elif MB(FORMBOT_TREX2PLUS)
+  #include "pins_FORMBOT_TREX2PLUS.h" // ATmega2560                                 env:megaatmega2560
+#elif MB(FORMBOT_TREX3)
+  #include "pins_FORMBOT_TREX3.h"     // ATmega2560                                 env:megaatmega2560
 #elif MB(RUMBA)
   #include "pins_RUMBA.h"             // ATmega2560                                 env:megaatmega2560
 #elif MB(BQ_ZUM_MEGA_3D)

Marlin/pins_FORMBOT_TREX2PLUS.h

@@ -0,0 +1,194 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Formbot pin assignments
+ */
+
+#ifndef __AVR_ATmega2560__
+  #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'"
+#endif
+
+#if HOTENDS > 2 || E_STEPPERS > 2
+  #error "Formbot supports up to 2 hotends / E-steppers. Comment this line to keep going."
+#endif
+
+#define DEFAULT_MACHINE_NAME "Formbot"
+#define BOARD_NAME           "Formbot"
+
+//
+// Servos
+//
+#define SERVO0_PIN         11
+#define SERVO1_PIN         -1    // was 6
+#define SERVO2_PIN         -1    // was 5
+#define SERVO3_PIN         -1
+
+//
+// Limit Switches
+//
+#define X_MIN_PIN           3
+#ifndef X_MAX_PIN
+  #define X_MAX_PIN         2
+#endif
+#define Y_MIN_PIN          14
+#define Y_MAX_PIN          15
+#define Z_MIN_PIN          18
+#define Z_MAX_PIN          19
+
+//
+// Z Probe (when not Z_MIN_PIN)
+//
+#ifndef Z_MIN_PROBE_PIN
+  #define Z_MIN_PROBE_PIN  32
+#endif
+
+//
+// Steppers
+//
+#define X_STEP_PIN         54
+#define X_DIR_PIN          55
+#define X_ENABLE_PIN       38
+#ifndef X_CS_PIN
+  #define X_CS_PIN         53
+#endif
+
+#define Y_STEP_PIN         60
+#define Y_DIR_PIN          61
+#define Y_ENABLE_PIN       56
+#ifndef Y_CS_PIN
+  #define Y_CS_PIN         49
+#endif
+
+#define Z_STEP_PIN         46
+#define Z_DIR_PIN          48
+#define Z_ENABLE_PIN       62
+#ifndef Z_CS_PIN
+  #define Z_CS_PIN         40
+#endif
+
+#define E0_STEP_PIN        26
+#define E0_DIR_PIN         28
+#define E0_ENABLE_PIN      24
+#ifndef E0_CS_PIN
+  #define E0_CS_PIN        42
+#endif
+
+#define E1_STEP_PIN        36
+#define E1_DIR_PIN         34
+#define E1_ENABLE_PIN      30
+#ifndef E1_CS_PIN
+  #define E1_CS_PIN        44
+#endif
+
+#define E2_STEP_PIN        42
+#define E2_DIR_PIN         43
+#define E2_ENABLE_PIN      44
+
+//
+// Temperature Sensors
+//
+#define TEMP_0_PIN         13   // Analog Input
+#define TEMP_1_PIN         15   // Analog Input
+#define TEMP_BED_PIN        3   // Analog Input
+
+// SPI for Max6675 or Max31855 Thermocouple
+#if DISABLED(SDSUPPORT)
+  #define MAX6675_SS_PIN   66 // Do not use pin 53 if there is even the remote possibility of using Display/SD card
+#else
+  #define MAX6675_SS_PIN   66 // Do not use pin 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present
+#endif
+
+//
+// Augmentation for auto-assigning RAMPS plugs
+//
+#if DISABLED(IS_RAMPS_EEB) &&  DISABLED(IS_RAMPS_EEF) &&  DISABLED(IS_RAMPS_EFB) &&  DISABLED(IS_RAMPS_EFF) &&  DISABLED(IS_RAMPS_SF) && !PIN_EXISTS(MOSFET_D)
+  #if HOTENDS > 1
+    #if TEMP_SENSOR_BED
+      #define IS_RAMPS_EEB
+    #else
+      #define IS_RAMPS_EEF
+    #endif
+  #elif TEMP_SENSOR_BED
+    #define IS_RAMPS_EFB
+  #else
+    #define IS_RAMPS_EFF
+  #endif
+#endif
+
+//
+// Heaters / Fans
+//
+#define HEATER_0_PIN       10
+#define HEATER_1_PIN        7
+#define HEATER_BED_PIN     58
+
+#define FAN_PIN             9
+
+#if ENABLED(FILAMENT_RUNOUT_SENSOR)
+  #define FIL_RUNOUT_PIN    4
+  //#define FIL_RUNOUT2_PIN  -1
+#else
+  // Though defined as a fan pin, it is utilized as a dedicated laser pin by Formbot.
+  #define FAN1_PIN          4
+#endif
+
+//
+// Misc. Functions
+//
+#define SDSS               53
+#ifndef LED_PIN
+  #define LED_PIN          13   // The Formbot v 1 board has almost no unassigned pins on it.  The Board's LED
+#endif                          // is a good place to get a signal to control the Max7219 LED Matrix.
+
+// Use the RAMPS 1.4 Analog input 5 on the AUX2 connector
+#define FILWIDTH_PIN        5   // Analog Input
+
+#ifndef PS_ON_PIN
+  #define PS_ON_PIN        12
+#endif
+
+#define CASE_LIGHT_PIN      8
+
+//
+// LCD / Controller
+//
+// Formbot only supports REPRAP_DISCOUNT_SMART_CONTROLLER
+//
+#if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER)
+  #ifndef BEEPER_PIN
+    #define BEEPER_PIN     37
+  #endif
+  #define BTN_EN1          31
+  #define BTN_EN2          33
+  #define BTN_ENC          35
+  #define SD_DETECT_PIN    49
+  #ifndef KILL_PIN
+    #define KILL_PIN       41
+  #endif
+  #define LCD_PINS_RS      16
+  #define LCD_PINS_ENABLE  17
+  #define LCD_PINS_D4      23
+  #define LCD_PINS_D5      25
+  #define LCD_PINS_D6      27
+  #define LCD_PINS_D7      29
+#endif

Marlin/pins_FORMBOT_TREX3.h

@@ -0,0 +1,174 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Formbot pin assignments
+ */
+
+#ifndef __AVR_ATmega2560__
+  #error "Oops! Select 'Arduino/Genuino Mega or Mega 2560' in 'Tools > Board.'"
+#endif
+
+#if HOTENDS > 2 || E_STEPPERS > 2
+  #error "Formbot supports up to 2 hotends / E-steppers. Comment this line to keep going."
+#endif
+
+#define DEFAULT_MACHINE_NAME "Formbot"
+#define BOARD_NAME           "Formbot"
+
+//
+// Servos
+//
+#define SERVO0_PIN         11
+#define SERVO1_PIN         -1    // was 6
+#define SERVO2_PIN         -1
+#define SERVO3_PIN         -1
+
+//
+// Limit Switches
+//
+#define X_MIN_PIN           3
+#ifndef X_MAX_PIN
+  #define X_MAX_PIN         2
+#endif
+#define Y_MIN_PIN          14
+#define Y_MAX_PIN          15
+#define Z_MIN_PIN          18
+#define Z_MAX_PIN          19
+
+//
+// Z Probe (when not Z_MIN_PIN)
+//
+#ifndef Z_MIN_PROBE_PIN
+  #define Z_MIN_PROBE_PIN  32
+#endif
+
+//
+// Steppers
+//
+#define X_STEP_PIN         54
+#define X_DIR_PIN          55
+#define X_ENABLE_PIN       38
+#ifndef X_CS_PIN
+  #define X_CS_PIN         53
+#endif
+
+#define Y_STEP_PIN         60
+#define Y_DIR_PIN          61
+#define Y_ENABLE_PIN       56
+#ifndef Y_CS_PIN
+  #define Y_CS_PIN         49
+#endif
+
+#define Z_STEP_PIN         46
+#define Z_DIR_PIN          48
+#define Z_ENABLE_PIN       62
+#ifndef Z_CS_PIN
+  #define Z_CS_PIN         40
+#endif
+
+#define E0_STEP_PIN        26
+#define E0_DIR_PIN         28
+#define E0_ENABLE_PIN      24
+#ifndef E0_CS_PIN
+  #define E0_CS_PIN        42
+#endif
+
+#define E1_STEP_PIN        36
+#define E1_DIR_PIN         34
+#define E1_ENABLE_PIN      30
+#ifndef E1_CS_PIN
+  #define E1_CS_PIN        44
+#endif
+
+#define E2_STEP_PIN        42
+#define E2_DIR_PIN         43
+#define E2_ENABLE_PIN      44
+
+//
+// Temperature Sensors
+//
+#define TEMP_0_PIN         13   // Analog Input
+#define TEMP_1_PIN         15   // Analog Input
+#define TEMP_BED_PIN       14   // Analog Input
+
+// SPI for Max6675 or Max31855 Thermocouple
+#if DISABLED(SDSUPPORT)
+  #define MAX6675_SS_PIN   66 // Do not use pin 53 if there is even the remote possibility of using Display/SD card
+#else
+  #define MAX6675_SS_PIN   66 // Do not use pin 49 as this is tied to the switch inside the SD card socket to detect if there is an SD card present
+#endif
+
+
+
+//
+// Heaters / Fans
+//
+#define HEATER_0_PIN       10
+#define HEATER_1_PIN        7
+#define HEATER_BED_PIN      8
+
+#define FAN_PIN             9
+#define FAN1_PIN           12
+
+#define NUM_RUNOUT_SENSORS  2
+#define FIL_RUNOUT_PIN     22
+#define FIL_RUNOUT2_PIN    21
+
+//
+// Misc. Functions
+//
+#define CASE_LIGHT_PIN      5
+#define SDSS               53
+#ifndef LED_PIN
+  #define LED_PIN          13
+#endif
+
+#define SPINDLE_LASER_PWM_PIN    -1   // MUST BE HARDWARE PWM
+#define SPINDLE_LASER_ENABLE_PIN 4    // Pin should have a pullup!
+
+// Use the RAMPS 1.4 Analog input 5 on the AUX2 connector
+#define FILWIDTH_PIN        5   // Analog Input
+
+//
+// LCD / Controller
+//
+// Formbot only supports REPRAP_DISCOUNT_SMART_CONTROLLER
+//
+#if ENABLED(REPRAP_DISCOUNT_SMART_CONTROLLER)
+  #define LCD_PINS_RS      16
+  #define LCD_PINS_ENABLE  17
+  #define LCD_PINS_D4      23
+  #define LCD_PINS_D5      25
+  #define LCD_PINS_D6      27
+  #define LCD_PINS_D7      29
+  #define BTN_EN1          31
+  #define BTN_EN2          33
+  #define BTN_ENC          35
+  #define SD_DETECT_PIN    49
+  #ifndef KILL_PIN
+    #define KILL_PIN       41
+  #endif
+  #ifndef BEEPER_PIN
+    #define BEEPER_PIN     37
+  #endif
+#endif

Marlin/runout.h

@@ -62,18 +62,23 @@ class FilamentRunoutSensor {
       #else
         // Read the sensor for the active extruder
         bool is_out;
-        switch (active_extruder) {
-          case 0: is_out = READ(FIL_RUNOUT_PIN) == FIL_RUNOUT_INVERTING; break;
-          case 1: is_out = READ(FIL_RUNOUT2_PIN) == FIL_RUNOUT_INVERTING; break;
-          #if NUM_RUNOUT_SENSORS > 2
-            case 2: is_out = READ(FIL_RUNOUT3_PIN) == FIL_RUNOUT_INVERTING; break;
-            #if NUM_RUNOUT_SENSORS > 3
-              case 3: is_out = READ(FIL_RUNOUT4_PIN) == FIL_RUNOUT_INVERTING; break;
-              #if NUM_RUNOUT_SENSORS > 4
-                case 4: is_out = READ(FIL_RUNOUT5_PIN) == FIL_RUNOUT_INVERTING; break;
+        if(extruder_duplication_enabled)
+        {
+          is_out = (READ(FIL_RUNOUT_PIN) == FIL_RUNOUT_INVERTING) || (READ(FIL_RUNOUT2_PIN) == FIL_RUNOUT_INVERTING);
+        } else {
+          switch (active_extruder) {
+            case 0: is_out = READ(FIL_RUNOUT_PIN) == FIL_RUNOUT_INVERTING; break;
+            case 1: is_out = READ(FIL_RUNOUT2_PIN) == FIL_RUNOUT_INVERTING; break;
+            #if NUM_RUNOUT_SENSORS > 2
+              case 2: is_out = READ(FIL_RUNOUT3_PIN) == FIL_RUNOUT_INVERTING; break;
+              #if NUM_RUNOUT_SENSORS > 3
+                case 3: is_out = READ(FIL_RUNOUT4_PIN) == FIL_RUNOUT_INVERTING; break;
+                #if NUM_RUNOUT_SENSORS > 4
+                  case 4: is_out = READ(FIL_RUNOUT5_PIN) == FIL_RUNOUT_INVERTING; break;
+                #endif
               #endif
             #endif
-          #endif
+          }
         }
       #endif
       return (is_out ? ++runout_count : (runout_count = 0)) > FIL_RUNOUT_THRESHOLD;

Marlin/stepper.cpp

@@ -222,7 +222,7 @@ int8_t Stepper::count_direction[NUM_AXIS] = {
   #define X_APPLY_DIR(v,ALWAYS) \
     if (extruder_duplication_enabled || ALWAYS) { \
       X_DIR_WRITE(v); \
-      X2_DIR_WRITE(v); \
+      X2_DIR_WRITE(mirrored_duplication_mode ? !(v) : v); \
     } \
     else { \
       if (movement_extruder()) X2_DIR_WRITE(v); else X_DIR_WRITE(v); \

Marlin/thermistornames.h

@@ -87,6 +87,8 @@
   #define THERMISTOR_NAME "PT100 1K"
 
 // High Temperature thermistors
+#elif THERMISTOR_ID == 61
+  #define THERMISTOR_NAME "Formbot 350°C"
 #elif THERMISTOR_ID == 66
   #define THERMISTOR_NAME "Dyze 4.7M"
 

Marlin/thermistortable_61.h

@@ -0,0 +1,115 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+// R25 = 100 kOhm, beta25 = 3950 K, 4.7 kOhm pull-up,
+// Formbot / Vivedino high temp 100k thermistor
+// 100KR13950181203
+// Generated with modified version of https://www.thingiverse.com/thing:103668
+// Using table 1 with datasheet values
+// Resistance         100k Ohms at 25deg. C
+// Resistance Tolerance     + / -1%
+// B Value             3950K at 25/50 deg. C
+// B Value Tolerance         + / - 1%
+const short temptable_61[][2] PROGMEM = {
+  { OV(   2.00), 420 }, // Guestimate to ensure we dont lose a reading and drop temps to -50 when over
+  { OV(  12.07), 350 },
+  { OV(  12.79), 345 },
+  { OV(  13.59), 340 },
+  { OV(  14.44), 335 },
+  { OV(  15.37), 330 },
+  { OV(  16.38), 325 },
+  { OV(  17.46), 320 },
+  { OV(  18.63), 315 },
+  { OV(  19.91), 310 },
+  { OV(  21.29), 305 },
+  { OV(  22.79), 300 },
+  { OV(  24.43), 295 },
+  { OV(  26.21), 290 },
+  { OV(  28.15), 285 },
+  { OV(  30.27), 280 },
+  { OV(  32.58), 275 },
+  { OV(  35.10), 270 },
+  { OV(  38.44), 265 },
+  { OV(  40.89), 260 },
+  { OV(  44.19), 255 },
+  { OV(  47.83), 250 },
+  { OV(  51.80), 245 },
+  { OV(  56.20), 240 },
+  { OV(  61.00), 235 },
+  { OV(  66.30), 230 },
+  { OV(  72.11), 225 },
+  { OV(  78.51), 220 },
+  { OV(  85.57), 215 },
+  { OV(  93.34), 210 },
+  { OV( 101.91), 205 },
+  { OV( 111.34), 200 },
+  { OV( 121.73), 195 },
+  { OV( 133.17), 190 },
+  { OV( 145.74), 185 },
+  { OV( 159.57), 180 },
+  { OV( 174.73), 175 },
+  { OV( 191.35), 170 },
+  { OV( 209.53), 165 },
+  { OV( 229.35), 160 },
+  { OV( 250.90), 155 },
+  { OV( 274.25), 150 },
+  { OV( 299.46), 145 },
+  { OV( 326.52), 140 },
+  { OV( 355.44), 135 },
+  { OV( 386.15), 130 },
+  { OV( 418.53), 125 },
+  { OV( 452.43), 120 },
+  { OV( 487.62), 115 },
+  { OV( 523.82), 110 },
+  { OV( 560.70), 105 },
+  { OV( 597.88), 100 },
+  { OV( 634.97),  95 },
+  { OV( 671.55),  90 },
+  { OV( 707.21),  85 },
+  { OV( 741.54),  80 },
+  { OV( 779.65),  75 },
+  { OV( 809.57),  70 },
+  { OV( 833.40),  65 },
+  { OV( 859.55),  60 },
+  { OV( 883.27),  55 },
+  { OV( 904.53),  50 },
+  { OV( 923.38),  45 },
+  { OV( 939.91),  40 },
+  { OV( 954.26),  35 },
+  { OV( 966.59),  30 },
+  { OV( 977.08),  25 },
+  { OV( 985.92),  20 },
+  { OV( 993.39),  15 },
+  { OV( 999.42),  10 },
+  { OV(1004.43),   5 },
+  { OV(1008.51),   0 },
+  { OV(1011.79),  -5 },
+  { OV(1014.40), -10 },
+  { OV(1016.48), -15 },
+  { OV(1018.10), -20 },
+  { OV(1019.35), -25 },
+  { OV(1020.32), -30 },
+  { OV(1021.05), -35 },
+  { OV(1021.60), -40 },
+  { OV(1022.01), -45 },
+  { OV(1022.31), -50 }
+};

Marlin/thermistortable_67.h

@@ -0,0 +1,80 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2019 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+// R25 = 500 KOhm, beta25 = 3800 K, 4.7 kOhm pull-up, SliceEngineering 450 °C Thermistor
+const short temptable_67[][2] PROGMEM = {
+  { OV(  22 ),  500 },
+  { OV(  23 ),  490 },
+  { OV(  25 ),  480 },
+  { OV(  27 ),  470 },
+  { OV(  29 ),  460 },
+  { OV(  32 ),  450 },
+  { OV(  35 ),  440 },
+  { OV(  38 ),  430 },
+  { OV(  41 ),  420 },
+  { OV(  45 ),  410 },
+  { OV(  50 ),  400 },
+  { OV(  55 ),  390 },
+  { OV(  60 ),  380 },
+  { OV(  67 ),  370 },
+  { OV(  74 ),  360 },
+  { OV(  82 ),  350 },
+  { OV(  91 ),  340 },
+  { OV( 102 ),  330 },
+  { OV( 114 ),  320 },
+  { OV( 127 ),  310 },
+  { OV( 143 ),  300 },
+  { OV( 161 ),  290 },
+  { OV( 181 ),  280 },
+  { OV( 204 ),  270 },
+  { OV( 229 ),  260 },
+  { OV( 259 ),  250 },
+  { OV( 290 ),  240 },
+  { OV( 325 ),  230 },
+  { OV( 364 ),  220 },
+  { OV( 407 ),  210 },
+  { OV( 453 ),  200 },
+  { OV( 501 ),  190 },
+  { OV( 551 ),  180 },
+  { OV( 603 ),  170 },
+  { OV( 655 ),  160 },
+  { OV( 706 ),  150 },
+  { OV( 755 ),  140 },
+  { OV( 801 ),  130 },
+  { OV( 842 ),  120 },
+  { OV( 879 ),  110 },
+  { OV( 910 ),  100 },
+  { OV( 936 ),   90 },
+  { OV( 948 ),   85 },
+  { OV( 958 ),   80 },
+  { OV( 975 ),   70 },
+  { OV( 988 ),   60 },
+  { OV( 998 ),   50 },
+  { OV(1006 ),   40 },
+  { OV(1011 ),   30 },
+  { OV(1013 ),   25 },
+  { OV(1015 ),   20 },
+  { OV(1018 ),   10 },
+  { OV(1020 ),    0 },
+  { OV(1021 ),  -10 },
+  { OV(1022 ),  -20 }
+};

Marlin/thermistortables.h

@@ -101,6 +101,9 @@
 #if ANY_THERMISTOR_IS(60) // Maker's Tool Works Kapton Bed Thermistor
   #include "thermistortable_60.h"
 #endif
+#if ANY_THERMISTOR_IS(61) // beta25 = 3950 K, R25 = 100 kOhm, Pull-up = 4.7 kOhm, "Formbot 350°C Thermistor"
+  #include "thermistortable_61.h"
+#endif
 #if ANY_THERMISTOR_IS(66) // DyzeDesign 500°C Thermistor
   #include "thermistortable_66.h"
 #endif

Marlin/ultralcd.cpp

@@ -505,7 +505,7 @@ uint16_t max_display_update_time = 0;
           if (currentScreen == lcd_status_screen)
             doubleclick_expire_ms = millis() + DOUBLECLICK_MAX_INTERVAL;
         }
-        else if (screen == lcd_status_screen && currentScreen == lcd_main_menu && PENDING(millis(), doubleclick_expire_ms) && (planner.movesplanned() || IS_SD_PRINTING()))
+        else if (screen == lcd_status_screen && currentScreen == lcd_main_menu && PENDING(millis(), doubleclick_expire_ms) && all_axes_known())
           screen =
             #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
               lcd_babystep_zoffset
@@ -972,6 +972,11 @@ void lcd_quick_feedback(const bool clear_buttons) {
       MENU_ITEM(gcode, MSG_BLTOUCH_SELFTEST, PSTR("M280 P" STRINGIFY(Z_PROBE_SERVO_NR) " S" STRINGIFY(BLTOUCH_SELFTEST)));
       MENU_ITEM(gcode, MSG_BLTOUCH_DEPLOY, PSTR("M280 P" STRINGIFY(Z_PROBE_SERVO_NR) " S" STRINGIFY(BLTOUCH_DEPLOY)));
       MENU_ITEM(gcode, MSG_BLTOUCH_STOW, PSTR("M280 P" STRINGIFY(Z_PROBE_SERVO_NR) " S" STRINGIFY(BLTOUCH_STOW)));
+      #if ENABLED(BLTOUCH_V3)
+        MENU_ITEM(gcode, MSG_BLTOUCH_SW_MODE, PSTR("M280 P" STRINGIFY(Z_PROBE_SERVO_NR) " S" STRINGIFY(BLTOUCH_SW_MODE)));
+        MENU_ITEM(gcode, MSG_BLTOUCH_5V_MODE, PSTR("M280 P" STRINGIFY(Z_PROBE_SERVO_NR) " S" STRINGIFY(BLTOUCH_5V_MODE)));
+        MENU_ITEM(gcode, MSG_BLTOUCH_OD_MODE, PSTR("M280 P" STRINGIFY(Z_PROBE_SERVO_NR) " S" STRINGIFY(BLTOUCH_OD_MODE)));
+      #endif
       END_MENU();
     }
 
@@ -1075,6 +1080,40 @@ void lcd_quick_feedback(const bool clear_buttons) {
 
   #endif
 
+
+#if ENABLED(DUAL_X_CARRIAGE)
+
+  void _recalc_IDEX_settings() {
+    if (active_extruder) {                      // For the 2nd extruder re-home so the next tool-change gets the new offsets.
+      enqueue_and_echo_commands_P(PSTR("G28")); // In future, we can babystep the 2nd extruder (if active), making homing unnecessary.
+      active_extruder = 0;
+    }
+  }
+
+  void menu_IDEX() {
+    START_MENU();
+    MENU_BACK(MSG_MAIN);
+
+    MENU_ITEM(gcode, MSG_IDEX_MODE_AUTOPARK,  PSTR("M605 S1\nG28 X\nG1 X100"));
+    const bool need_g28 = !(TEST(axis_known_position, Y_AXIS) && TEST(axis_known_position, Z_AXIS));
+    MENU_ITEM(gcode, MSG_IDEX_MODE_DUPLICATE, need_g28
+      ? PSTR("M605 S1\nT0\nG28\nM605 S2 X200\nG28 X\nG1 X100")                // If Y or Z is not homed, do a full G28 first
+      : PSTR("M605 S1\nT0\nM605 S2 X200\nG28 X\nG1 X100")
+    );
+    MENU_ITEM(gcode, MSG_IDEX_MODE_SCALED_COPY, need_g28
+      ? PSTR("M605 S1\nT0\nG28\nM605 S2 X200\nG28 X\nG1 X100\nM605 S3 X200")  // If Y or Z is not homed, do a full G28 first
+      : PSTR("M605 S1\nT0\nM605 S2 X200\nG28 X\nG1 X100\nM605 S3 X200")
+    );
+    MENU_ITEM(gcode, MSG_IDEX_MODE_FULL_CTRL, PSTR("M605 S0\nG28 X"));
+    MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(float52, MSG_IDEX_X_OFFSET , &hotend_offset[X_AXIS][1], MIN(X2_HOME_POS, X2_MAX_POS) - 25.0, MAX(X2_HOME_POS, X2_MAX_POS) + 25.0, _recalc_IDEX_settings);
+    MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(float52, MSG_IDEX_Y_OFFSET , &hotend_offset[Y_AXIS][1], -10.0, 10.0, _recalc_IDEX_settings);
+    MENU_MULTIPLIER_ITEM_EDIT_CALLBACK(float52, MSG_IDEX_Z_OFFSET , &hotend_offset[Z_AXIS][1], -10.0, 10.0, _recalc_IDEX_settings);
+    MENU_ITEM(gcode, MSG_IDEX_SAVE_OFFSETS, PSTR("M500"));
+    END_MENU();
+  }
+
+#endif
+
   /**
    *
    * "Main" menu
@@ -1100,13 +1139,14 @@ void lcd_quick_feedback(const bool clear_buttons) {
     // Set Case light on/off/brightness
     //
     #if ENABLED(MENU_ITEM_CASE_LIGHT)
-      if (USEABLE_HARDWARE_PWM(CASE_LIGHT_PIN)) {
-        MENU_ITEM(submenu, MSG_CASE_LIGHT, case_light_menu);
-      }
-      else
         MENU_ITEM_EDIT_CALLBACK(bool, MSG_CASE_LIGHT, (bool*)&case_light_on, update_case_light);
     #endif
 
+    #if ENABLED(SPINDLE_LASER_ENABLE)
+	    MENU_ITEM(gcode, MSG_LASER_ON, PSTR("M3"));
+	    MENU_ITEM(gcode, MSG_LASER_OFF, PSTR("M5"));
+	#endif
+
     if (planner.movesplanned() || IS_SD_PRINTING())
       MENU_ITEM(submenu, MSG_TUNE, lcd_tune_menu);
     else
@@ -1138,6 +1178,10 @@ void lcd_quick_feedback(const bool clear_buttons) {
       }
     #endif // SDSUPPORT
 
+    #if ENABLED(DUAL_X_CARRIAGE)
+      MENU_ITEM(submenu, MSG_IDEX_MENU, menu_IDEX);
+    #endif
+
     #if ENABLED(LCD_INFO_MENU)
       MENU_ITEM(submenu, MSG_INFO_MENU, lcd_info_menu);
     #endif