Update Configuration_adv.h

Marlin/Configuration.h

@@ -1,5 +1,4 @@
-/**
- * Marlin 3D Printer Firmware
+ /** Marlin 3D Printer Firmware
  * Copyright (c) 2020 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
  *
  * Based on Sprinter and grbl.
@@ -69,7 +68,7 @@
 // @section info
 
 // Author info of this build printed to the host during boot and M115
-#define STRING_CONFIG_H_AUTHOR "(none, default config)" // Who made the changes.
+#define STRING_CONFIG_H_AUTHOR "3DXtech / Insanity Automation" // Who made the changes.
 //#define CUSTOM_VERSION_FILE Version.h // Path from the root directory (no quotes)
 
 /**
@@ -127,7 +126,7 @@
 
 // Choose the name from boards.h that matches your setup
 #ifndef MOTHERBOARD
-  #define MOTHERBOARD BOARD_RAMPS_14_EFB
+  #define MOTHERBOARD BOARD_INTAMSYS40
 #endif
 
 // Name displayed in the LCD "Ready" message and Info menu
@@ -311,29 +310,29 @@
  * Enable and connect the power supply to the PS_ON_PIN.
  * Specify whether the power supply is active HIGH or active LOW.
  */
-//#define PSU_CONTROL
+#define PSU_CONTROL
 //#define PSU_NAME "Power Supply"
 
 #if ENABLED(PSU_CONTROL)
-  #define PSU_ACTIVE_STATE LOW      // Set 'LOW' for ATX, 'HIGH' for X-Box
+  #define PSU_ACTIVE_STATE HIGH      // Set 'LOW' for ATX, 'HIGH' for X-Box
 
   //#define PSU_DEFAULT_OFF         // Keep power off until enabled directly with M80
-  //#define PSU_POWERUP_DELAY 250   // (ms) Delay for the PSU to warm up to full power
+  #define PSU_POWERUP_DELAY 250   // (ms) Delay for the PSU to warm up to full power
 
   //#define PSU_POWERUP_GCODE  "M355 S1"  // G-code to run after power-on (e.g., case light on)
   //#define PSU_POWEROFF_GCODE "M355 S0"  // G-code to run before power-off (e.g., case light off)
 
-  //#define AUTO_POWER_CONTROL      // Enable automatic control of the PS_ON pin
+  #define AUTO_POWER_CONTROL      // Enable automatic control of the PS_ON pin
   #if ENABLED(AUTO_POWER_CONTROL)
     #define AUTO_POWER_FANS         // Turn on PSU if fans need power
     #define AUTO_POWER_E_FANS
     #define AUTO_POWER_CONTROLLERFAN
     #define AUTO_POWER_CHAMBER_FAN
     #define AUTO_POWER_COOLER_FAN
-    //#define AUTO_POWER_E_TEMP        50 // (°C) Turn on PSU if any extruder is over this temperature
-    //#define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU if the chamber is over this temperature
+    #define AUTO_POWER_E_TEMP        50 // (°C) Turn on PSU if any extruder is over this temperature
+    #define AUTO_POWER_CHAMBER_TEMP  30 // (°C) Turn on PSU if the chamber is over this temperature
     //#define AUTO_POWER_COOLER_TEMP   26 // (°C) Turn on PSU if the cooler is over this temperature
-    #define POWER_TIMEOUT              30 // (s) Turn off power if the machine is idle for this duration
+    #define POWER_TIMEOUT              120 // (s) Turn off power if the machine is idle for this duration
     //#define POWER_OFF_DELAY          60 // (s) Delay of poweroff after M81 command. Useful to let fans run for extra time.
   #endif
 #endif
@@ -409,7 +408,7 @@
  *   998 : Dummy Table that ALWAYS reads 25°C or the temperature defined below.
  *   999 : Dummy Table that ALWAYS reads 100°C or the temperature defined below.
  */
-#define TEMP_SENSOR_0 1
+#define TEMP_SENSOR_0 20
 #define TEMP_SENSOR_1 0
 #define TEMP_SENSOR_2 0
 #define TEMP_SENSOR_3 0
@@ -417,9 +416,9 @@
 #define TEMP_SENSOR_5 0
 #define TEMP_SENSOR_6 0
 #define TEMP_SENSOR_7 0
-#define TEMP_SENSOR_BED 0
+#define TEMP_SENSOR_BED 1
 #define TEMP_SENSOR_PROBE 0
-#define TEMP_SENSOR_CHAMBER 0
+#define TEMP_SENSOR_CHAMBER 1
 #define TEMP_SENSOR_COOLER 0
 
 // Dummy thermistor constant temperature readings, for use with 998 and 999
@@ -437,17 +436,17 @@
 //#define TEMP_SENSOR_1_AS_REDUNDANT
 #define MAX_REDUNDANT_TEMP_SENSOR_DIFF 10
 
-#define TEMP_RESIDENCY_TIME     10  // (seconds) Time to wait for hotend to "settle" in M109
-#define TEMP_WINDOW              1  // (°C) Temperature proximity for the "temperature reached" timer
-#define TEMP_HYSTERESIS          3  // (°C) Temperature proximity considered "close enough" to the target
+#define TEMP_RESIDENCY_TIME      3  // (seconds) Time to wait for hotend to "settle" in M109
+#define TEMP_WINDOW              3  // (°C) Temperature proximity for the "temperature reached" timer
+#define TEMP_HYSTERESIS          5  // (°C) Temperature proximity considered "close enough" to the target
 
-#define TEMP_BED_RESIDENCY_TIME 10  // (seconds) Time to wait for bed to "settle" in M190
+#define TEMP_BED_RESIDENCY_TIME  5  // (seconds) Time to wait for bed to "settle" in M190
 #define TEMP_BED_WINDOW          1  // (°C) Temperature proximity for the "temperature reached" timer
 #define TEMP_BED_HYSTERESIS      3  // (°C) Temperature proximity considered "close enough" to the target
 
 #define TEMP_CHAMBER_RESIDENCY_TIME 10  // (seconds) Time to wait for chamber to "settle" in M191
 #define TEMP_CHAMBER_WINDOW      1  // (°C) Temperature proximity for the "temperature reached" timer
-#define TEMP_CHAMBER_HYSTERESIS  3  // (°C) Temperature proximity considered "close enough" to the target
+#define TEMP_CHAMBER_HYSTERESIS  5  // (°C) Temperature proximity considered "close enough" to the target
 
 // Below this temperature the heater will be switched off
 // because it probably indicates a broken thermistor wire.
@@ -465,7 +464,7 @@
 // Above this temperature the heater will be switched off.
 // This can protect components from overheating, but NOT from shorts and failures.
 // (Use MINTEMP for thermistor short/failure protection.)
-#define HEATER_0_MAXTEMP 275
+#define HEATER_0_MAXTEMP 415
 #define HEATER_1_MAXTEMP 275
 #define HEATER_2_MAXTEMP 275
 #define HEATER_3_MAXTEMP 275
@@ -474,7 +473,7 @@
 #define HEATER_6_MAXTEMP 275
 #define HEATER_7_MAXTEMP 275
 #define BED_MAXTEMP      150
-#define CHAMBER_MAXTEMP  60
+#define CHAMBER_MAXTEMP  80
 
 /**
  * Thermal Overshoot
@@ -497,8 +496,8 @@
 #define PID_K1 0.95      // Smoothing factor within any PID loop
 
 #if ENABLED(PIDTEMP)
-  //#define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
-  //#define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
+  #define PID_EDIT_MENU         // Add PID editing to the "Advanced Settings" menu. (~700 bytes of PROGMEM)
+  #define PID_AUTOTUNE_MENU     // Add PID auto-tuning to the "Advanced Settings" menu. (~250 bytes of PROGMEM)
   //#define PID_PARAMS_PER_HOTEND // Uses separate PID parameters for each extruder (useful for mismatched extruders)
                                   // Set/get with gcode: M301 E[extruder number, 0-2]
 
@@ -509,9 +508,9 @@
     #define DEFAULT_Ki_LIST {   1.08,   1.08 }
     #define DEFAULT_Kd_LIST { 114.00, 114.00 }
   #else
-    #define DEFAULT_Kp  22.20
-    #define DEFAULT_Ki   1.08
-    #define DEFAULT_Kd 114.00
+    #define DEFAULT_Kp 10.5
+  #define DEFAULT_Ki 0.45
+  #define DEFAULT_Kd 70
   #endif
 #endif // PIDTEMP
 
@@ -532,7 +531,7 @@
  * heater. If your configuration is significantly different than this and you don't understand
  * the issues involved, don't use bed PID until someone else verifies that your hardware works.
  */
-//#define PIDTEMPBED
+#define PIDTEMPBED
 
 //#define BED_LIMIT_SWITCHING
 
@@ -548,11 +547,11 @@
   //#define MIN_BED_POWER 0
   //#define PID_BED_DEBUG // Sends debug data to the serial port.
 
-  // 120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
-  // from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define DEFAULT_bedKp 10.00
-  #define DEFAULT_bedKi .023
-  #define DEFAULT_bedKd 305.4
+  //120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
+  //from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
+  #define DEFAULT_bedKp 104.28
+  #define DEFAULT_bedKi 20.53
+  #define DEFAULT_bedKd 353.10
 
   // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #endif // PIDTEMPBED
@@ -709,13 +708,13 @@
 #endif
 
 // Mechanical endstop with COM to ground and NC to Signal uses "false" here (most common setup).
-#define X_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define Y_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define Z_MIN_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define X_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define Y_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define Z_MAX_ENDSTOP_INVERTING false // Set to true to invert the logic of the endstop.
-#define Z_MIN_PROBE_ENDSTOP_INVERTING false // Set to true to invert the logic of the probe.
+#define X_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MIN_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define X_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Y_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MAX_ENDSTOP_INVERTING true // Set to true to invert the logic of the endstop.
+#define Z_MIN_PROBE_ENDSTOP_INVERTING true // Set to true to invert the logic of the probe.
 
 /**
  * Stepper Drivers
@@ -798,14 +797,14 @@
  * Override with M92
  *                                      X, Y, Z, E0 [, E1[, E2...]]
  */
-#define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 80, 400, 500 }
+#define DEFAULT_AXIS_STEPS_PER_UNIT   { 80, 80, 800, 92.6 }
 
 /**
  * Default Max Feed Rate (mm/s)
  * Override with M203
  *                                      X, Y, Z, E0 [, E1[, E2...]]
  */
-#define DEFAULT_MAX_FEEDRATE          { 300, 300, 5, 25 }
+#define DEFAULT_MAX_FEEDRATE          { 300, 300, 20, 70 }
 
 //#define LIMITED_MAX_FR_EDITING        // Limit edit via M203 or LCD to DEFAULT_MAX_FEEDRATE * 2
 #if ENABLED(LIMITED_MAX_FR_EDITING)
@@ -818,7 +817,7 @@
  * Override with M201
  *                                      X, Y, Z, E0 [, E1[, E2...]]
  */
-#define DEFAULT_MAX_ACCELERATION      { 3000, 3000, 100, 10000 }
+#define DEFAULT_MAX_ACCELERATION      { 9000, 9000, 100, 10000 }
 
 //#define LIMITED_MAX_ACCEL_EDITING     // Limit edit via M201 or LCD to DEFAULT_MAX_ACCELERATION * 2
 #if ENABLED(LIMITED_MAX_ACCEL_EDITING)
@@ -845,7 +844,7 @@
  * When changing speed and direction, if the difference is less than the
  * value set here, it may happen instantaneously.
  */
-//#define CLASSIC_JERK
+#define CLASSIC_JERK
 #if ENABLED(CLASSIC_JERK)
   #define DEFAULT_XJERK 10.0
   #define DEFAULT_YJERK 10.0
@@ -882,7 +881,7 @@
  *
  * See https://github.com/synthetos/TinyG/wiki/Jerk-Controlled-Motion-Explained
  */
-//#define S_CURVE_ACCELERATION
+#define S_CURVE_ACCELERATION
 
 //===========================================================================
 //============================= Z Probe Options =============================
@@ -1124,8 +1123,8 @@
 #define Z_PROBE_LOW_POINT          -2 // Farthest distance below the trigger-point to go before stopping
 
 // For M851 give a range for adjusting the Z probe offset
-#define Z_PROBE_OFFSET_RANGE_MIN -20
-#define Z_PROBE_OFFSET_RANGE_MAX 20
+#define Z_PROBE_OFFSET_RANGE_MIN -9
+#define Z_PROBE_OFFSET_RANGE_MAX 9
 
 // Enable the M48 repeatability test to test probe accuracy
 //#define Z_MIN_PROBE_REPEATABILITY_TEST
@@ -1183,9 +1182,9 @@
 // @section machine
 
 // Invert the stepper direction. Change (or reverse the motor connector) if an axis goes the wrong way.
-#define INVERT_X_DIR false
-#define INVERT_Y_DIR true
-#define INVERT_Z_DIR false
+#define INVERT_X_DIR true
+#define INVERT_Y_DIR false
+#define INVERT_Z_DIR true
 
 // @section extruder
 
@@ -1225,8 +1224,8 @@
 // @section machine
 
 // The size of the print bed
-#define X_BED_SIZE 200
-#define Y_BED_SIZE 200
+#define X_BED_SIZE 260
+#define Y_BED_SIZE 260
 
 // Travel limits (mm) after homing, corresponding to endstop positions.
 #define X_MIN_POS 0
@@ -1234,7 +1233,7 @@
 #define Z_MIN_POS 0
 #define X_MAX_POS X_BED_SIZE
 #define Y_MAX_POS Y_BED_SIZE
-#define Z_MAX_POS 200
+#define Z_MAX_POS 260
 
 /**
  * Software Endstops
@@ -1262,7 +1261,7 @@
 #endif
 
 #if EITHER(MIN_SOFTWARE_ENDSTOPS, MAX_SOFTWARE_ENDSTOPS)
-  //#define SOFT_ENDSTOPS_MENU_ITEM  // Enable/Disable software endstops from the LCD
+  #define SOFT_ENDSTOPS_MENU_ITEM  // Enable/Disable software endstops from the LCD
 #endif
 
 /**
@@ -1278,7 +1277,7 @@
  * RAMPS-based boards use SERVO3_PIN for the first runout sensor.
  * For other boards you may need to define FIL_RUNOUT_PIN, FIL_RUNOUT2_PIN, etc.
  */
-//#define FILAMENT_RUNOUT_SENSOR
+#define FILAMENT_RUNOUT_SENSOR
 #if ENABLED(FILAMENT_RUNOUT_SENSOR)
   #define FIL_RUNOUT_ENABLED_DEFAULT true // Enable the sensor on startup. Override with M412 followed by M500.
   #define NUM_RUNOUT_SENSORS   1          // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
@@ -1330,7 +1329,7 @@
   // After a runout is detected, continue printing this length of filament
   // before executing the runout script. Useful for a sensor at the end of
   // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead.
-  //#define FILAMENT_RUNOUT_DISTANCE_MM 25
+  #define FILAMENT_RUNOUT_DISTANCE_MM 5
 
   #ifdef FILAMENT_RUNOUT_DISTANCE_MM
     // Enable this option to use an encoder disc that toggles the runout pin
@@ -1382,14 +1381,14 @@
 //#define AUTO_BED_LEVELING_LINEAR
 //#define AUTO_BED_LEVELING_BILINEAR
 //#define AUTO_BED_LEVELING_UBL
-//#define MESH_BED_LEVELING
+#define MESH_BED_LEVELING
 
 /**
  * Normally G28 leaves leveling disabled on completion. Enable one of
  * these options to restore the prior leveling state or to always enable
  * leveling immediately after G28.
  */
-//#define RESTORE_LEVELING_AFTER_G28
+#define RESTORE_LEVELING_AFTER_G28
 //#define ENABLE_LEVELING_AFTER_G28
 
 /**
@@ -1426,7 +1425,7 @@
   /**
    * Enable the G26 Mesh Validation Pattern tool.
    */
-  //#define G26_MESH_VALIDATION
+  #define G26_MESH_VALIDATION
   #if ENABLED(G26_MESH_VALIDATION)
     #define MESH_TEST_NOZZLE_SIZE    0.4  // (mm) Diameter of primary nozzle.
     #define MESH_TEST_LAYER_HEIGHT   0.2  // (mm) Default layer height for G26.
@@ -1491,7 +1490,7 @@
   //===========================================================================
 
   #define MESH_INSET 10          // Set Mesh bounds as an inset region of the bed
-  #define GRID_MAX_POINTS_X 3    // Don't use more than 7 points per axis, implementation limited.
+  #define GRID_MAX_POINTS_X 5    // Don't use more than 7 points per axis, implementation limited.
   #define GRID_MAX_POINTS_Y GRID_MAX_POINTS_X
 
   //#define MESH_G28_REST_ORIGIN // After homing all axes ('G28' or 'G28 XYZ') rest Z at Z_MIN_POS
@@ -1502,16 +1501,16 @@
  * Add a bed leveling sub-menu for ABL or MBL.
  * Include a guided procedure if manual probing is enabled.
  */
-//#define LCD_BED_LEVELING
+#define LCD_BED_LEVELING
 
 #if ENABLED(LCD_BED_LEVELING)
   #define MESH_EDIT_Z_STEP  0.025 // (mm) Step size while manually probing Z axis.
   #define LCD_PROBE_Z_RANGE 4     // (mm) Z Range centered on Z_MIN_POS for LCD Z adjustment
-  //#define MESH_EDIT_MENU        // Add a menu to edit mesh points
+  #define MESH_EDIT_MENU        // Add a menu to edit mesh points
 #endif
 
 // Add a menu item to move between bed corners for manual bed adjustment
-//#define LEVEL_BED_CORNERS
+#define LEVEL_BED_CORNERS
 
 #if ENABLED(LEVEL_BED_CORNERS)
   #define LEVEL_CORNERS_INSET_LFRB { 30, 30, 30, 30 } // (mm) Left, Front, Right, Back insets
@@ -1656,12 +1655,12 @@
  *   M501 - Read settings from EEPROM. (i.e., Throw away unsaved changes)
  *   M502 - Revert settings to "factory" defaults. (Follow with M500 to init the EEPROM.)
  */
-//#define EEPROM_SETTINGS     // Persistent storage with M500 and M501
+#define EEPROM_SETTINGS     // Persistent storage with M500 and M501
 //#define DISABLE_M503        // Saves ~2700 bytes of PROGMEM. Disable for release!
 #define EEPROM_CHITCHAT       // Give feedback on EEPROM commands. Disable to save PROGMEM.
 #define EEPROM_BOOT_SILENT    // Keep M503 quiet and only give errors during first load
 #if ENABLED(EEPROM_SETTINGS)
-  //#define EEPROM_AUTO_INIT  // Init EEPROM automatically on any errors.
+  #define EEPROM_AUTO_INIT  // Init EEPROM automatically on any errors.
 #endif
 
 //
@@ -1698,7 +1697,7 @@
 #define PREHEAT_2_LABEL       "ABS"
 #define PREHEAT_2_TEMP_HOTEND 240
 #define PREHEAT_2_TEMP_BED    110
-#define PREHEAT_2_TEMP_CHAMBER 35
+#define PREHEAT_2_TEMP_CHAMBER 45
 #define PREHEAT_2_FAN_SPEED     0 // Value from 0 to 255
 
 /**
@@ -1712,11 +1711,11 @@
  *    P1  Raise the nozzle always to Z-park height.
  *    P2  Raise the nozzle by Z-park amount, limited to Z_MAX_POS.
  */
-//#define NOZZLE_PARK_FEATURE
+#define NOZZLE_PARK_FEATURE
 
 #if ENABLED(NOZZLE_PARK_FEATURE)
   // Specify a park position as { X, Y, Z_raise }
-  #define NOZZLE_PARK_POINT { (X_MIN_POS + 10), (Y_MAX_POS - 10), 20 }
+  #define NOZZLE_PARK_POINT { (X_CENTER), (Y_CENTER), 20 }
   //#define NOZZLE_PARK_X_ONLY          // X move only is required to park
   //#define NOZZLE_PARK_Y_ONLY          // Y move only is required to park
   #define NOZZLE_PARK_Z_RAISE_MIN   2   // (mm) Always raise Z by at least this distance
@@ -1920,7 +1919,7 @@
  * SD Card support is disabled by default. If your controller has an SD slot,
  * you must uncomment the following option or it won't work.
  */
-//#define SDSUPPORT
+#define SDSUPPORT
 
 /**
  * SD CARD: ENABLE CRC
@@ -1990,7 +1989,7 @@
 //
 // Add individual axis homing items (Home X, Home Y, and Home Z) to the LCD menu.
 //
-//#define INDIVIDUAL_AXIS_HOMING_MENU
+#define INDIVIDUAL_AXIS_HOMING_MENU
 
 //
 // SPEAKER/BUZZER
@@ -1998,7 +1997,7 @@
 // If you have a speaker that can produce tones, enable it here.
 // By default Marlin assumes you have a buzzer with a fixed frequency.
 //
-//#define SPEAKER
+#define SPEAKER
 
 //
 // The duration and frequency for the UI feedback sound.
@@ -2179,7 +2178,7 @@
 // RepRapDiscount FULL GRAPHIC Smart Controller
 // https://reprap.org/wiki/RepRapDiscount_Full_Graphic_Smart_Controller
 //
-//#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
+#define REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
 
 //
 // K.3D Full Graphic Smart Controller

Marlin/Configuration_adv.h

@@ -152,7 +152,7 @@
 #if DISABLED(PIDTEMPCHAMBER)
   #define CHAMBER_CHECK_INTERVAL 5000   // (ms) Interval between checks in bang-bang control
   #if ENABLED(CHAMBER_LIMIT_SWITCHING)
-    #define CHAMBER_HYSTERESIS 2        // (°C) Only set the relevant heater state when ABS(T-target) > CHAMBER_HYSTERESIS
+    #define CHAMBER_HYSTERESIS 5        // (°C) Only set the relevant heater state when ABS(T-target) > CHAMBER_HYSTERESIS
   #endif
 #endif
 
@@ -221,12 +221,12 @@
  * THERMAL_PROTECTION_HYSTERESIS and/or THERMAL_PROTECTION_PERIOD
  */
 #if ENABLED(THERMAL_PROTECTION_HOTENDS)
-  #define THERMAL_PROTECTION_PERIOD 40        // Seconds
-  #define THERMAL_PROTECTION_HYSTERESIS 4     // Degrees Celsius
+  #define THERMAL_PROTECTION_PERIOD 70        // Seconds
+  #define THERMAL_PROTECTION_HYSTERESIS 10     // Degrees Celsius
 
-  //#define ADAPTIVE_FAN_SLOWING              // Slow part cooling fan if temperature drops
+  #define ADAPTIVE_FAN_SLOWING              // Slow part cooling fan if temperature drops
   #if BOTH(ADAPTIVE_FAN_SLOWING, PIDTEMP)
-    //#define NO_FAN_SLOWING_IN_PID_TUNING    // Don't slow fan speed during M303
+    #define NO_FAN_SLOWING_IN_PID_TUNING    // Don't slow fan speed during M303
   #endif
 
   /**
@@ -241,7 +241,7 @@
    * and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set
    * below 2.
    */
-  #define WATCH_TEMP_PERIOD  20               // Seconds
+  #define WATCH_TEMP_PERIOD 40                // Seconds
   #define WATCH_TEMP_INCREASE 2               // Degrees Celsius
 #endif
 
@@ -249,27 +249,27 @@
  * Thermal Protection parameters for the bed are just as above for hotends.
  */
 #if ENABLED(THERMAL_PROTECTION_BED)
-  #define THERMAL_PROTECTION_BED_PERIOD        20 // Seconds
+  #define THERMAL_PROTECTION_BED_PERIOD        30 // Seconds
   #define THERMAL_PROTECTION_BED_HYSTERESIS     2 // Degrees Celsius
 
   /**
    * As described above, except for the bed (M140/M190/M303).
    */
   #define WATCH_BED_TEMP_PERIOD                60 // Seconds
-  #define WATCH_BED_TEMP_INCREASE               2 // Degrees Celsius
+  #define WATCH_BED_TEMP_INCREASE               1 // Degrees Celsius
 #endif
 
 /**
  * Thermal Protection parameters for the heated chamber.
  */
 #if ENABLED(THERMAL_PROTECTION_CHAMBER)
-  #define THERMAL_PROTECTION_CHAMBER_PERIOD    20 // Seconds
+  #define THERMAL_PROTECTION_CHAMBER_PERIOD    60 // Seconds
   #define THERMAL_PROTECTION_CHAMBER_HYSTERESIS 2 // Degrees Celsius
 
   /**
    * Heated chamber watch settings (M141/M191).
    */
-  #define WATCH_CHAMBER_TEMP_PERIOD            60 // Seconds
+  #define WATCH_CHAMBER_TEMP_PERIOD            360 // Seconds
   #define WATCH_CHAMBER_TEMP_INCREASE           2 // Degrees Celsius
 #endif
 
@@ -556,13 +556,13 @@
 /**
  * M355 Case Light on-off / brightness
  */
-//#define CASE_LIGHT_ENABLE
+#define CASE_LIGHT_ENABLE
 #if ENABLED(CASE_LIGHT_ENABLE)
   //#define CASE_LIGHT_PIN 4                  // Override the default pin if needed
   #define INVERT_CASE_LIGHT false             // Set true if Case Light is ON when pin is LOW
   #define CASE_LIGHT_DEFAULT_ON true          // Set default power-up state on
-  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 105   // Set default power-up brightness (0-255, requires PWM pin)
-  //#define CASE_LIGHT_NO_BRIGHTNESS          // Disable brightness control. Enable for non-PWM lighting.
+  #define CASE_LIGHT_DEFAULT_BRIGHTNESS 255   // Set default power-up brightness (0-255, requires PWM pin)
+  #define CASE_LIGHT_NO_BRIGHTNESS          // Disable brightness control. Enable for non-PWM lighting.
   //#define CASE_LIGHT_MAX_PWM 128            // Limit PWM duty cycle (0-255)
   //#define CASE_LIGHT_MENU                   // Add Case Light options to the LCD menu
   #if ENABLED(NEOPIXEL_LED)
@@ -724,7 +724,7 @@
 
 //#define HOMING_BACKOFF_POST_MM { 2, 2, 2 }  // (mm) Backoff from endstops after homing
 
-//#define QUICK_HOME                          // If G28 contains XY do a diagonal move first
+#define QUICK_HOME                          // If G28 contains XY do a diagonal move first
 //#define HOME_Y_BEFORE_X                     // If G28 contains XY home Y before X
 //#define HOME_Z_FIRST                        // Home Z first. Requires a Z-MIN endstop (not a probe).
 //#define CODEPENDENT_XY_HOMING               // If X/Y can't home without homing Y/X first
@@ -898,10 +898,10 @@
 //#define MULTI_NOZZLE_DUPLICATION
 
 // By default pololu step drivers require an active high signal. However, some high power drivers require an active low signal as step.
-#define INVERT_X_STEP_PIN false
-#define INVERT_Y_STEP_PIN false
-#define INVERT_Z_STEP_PIN false
-#define INVERT_E_STEP_PIN false
+#define INVERT_X_STEP_PIN true
+#define INVERT_Y_STEP_PIN true
+#define INVERT_Z_STEP_PIN true
+#define INVERT_E_STEP_PIN true
 
 /**
  * Idle Stepper Shutdown
@@ -1075,7 +1075,7 @@
  *    M908 - BQ_ZUM_MEGA_3D, RAMBO, PRINTRBOARD_REVF, RIGIDBOARD_V2 & SCOOVO_X9H
  *    M909, M910 & LCD - only PRINTRBOARD_REVF & RIGIDBOARD_V2
  */
-//#define PWM_MOTOR_CURRENT { 1300, 1300, 1250 }          // Values in milliamps
+#define PWM_MOTOR_CURRENT { 1300, 1300, 1250 }          // Values in milliamps
 //#define DIGIPOT_MOTOR_CURRENT { 135,135,135,135,135 }   // Values 0-255 (RAMBO 135 = ~0.75A, 185 = ~1A)
 //#define DAC_MOTOR_CURRENT_DEFAULT { 70, 80, 90, 80 }    // Default drive percent - X, Y, Z, E axis
 
@@ -1199,7 +1199,7 @@
 
 #if HAS_DISPLAY
   // The timeout (in ms) to return to the status screen from sub-menus
-  //#define LCD_TIMEOUT_TO_STATUS 15000
+  #define LCD_TIMEOUT_TO_STATUS 15000
 
   #if ENABLED(SHOW_BOOTSCREEN)
     #define BOOTSCREEN_TIMEOUT 4000      // (ms) Total Duration to display the boot screen(s)
@@ -1209,13 +1209,13 @@
   #endif
 
   // Scroll a longer status message into view
-  //#define STATUS_MESSAGE_SCROLLING
+  #define STATUS_MESSAGE_SCROLLING
 
   // On the Info Screen, display XY with one decimal place when possible
   //#define LCD_DECIMAL_SMALL_XY
 
   // Add an 'M73' G-code to set the current percentage
-  //#define LCD_SET_PROGRESS_MANUALLY
+  #define LCD_SET_PROGRESS_MANUALLY
 
   // Show the E position (filament used) during printing
   //#define LCD_SHOW_E_TOTAL
@@ -1361,10 +1361,10 @@
   //#define UTF_FILENAME_SUPPORT
 
   // This allows hosts to request long names for files and folders with M33
-  //#define LONG_FILENAME_HOST_SUPPORT
+  #define LONG_FILENAME_HOST_SUPPORT
 
   // Enable this option to scroll long filenames in the SD card menu
-  //#define SCROLL_LONG_FILENAMES
+  #define SCROLL_LONG_FILENAMES
 
   // Leave the heaters on after Stop Print (not recommended!)
   //#define SD_ABORT_NO_COOLDOWN
@@ -1386,7 +1386,7 @@
   /**
    * Auto-report SdCard status with M27 S<seconds>
    */
-  //#define AUTO_REPORT_SD_STATUS
+  #define AUTO_REPORT_SD_STATUS
 
   /**
    * Support for USB thumb drives using an Arduino USB Host Shield or
@@ -1543,6 +1543,7 @@
   //#define STATUS_ALT_FAN_BITMAP     // Use the alternative fan bitmap
   //#define STATUS_FAN_FRAMES 3       // :[0,1,2,3,4] Number of fan animation frames
   //#define STATUS_HEAT_PERCENT       // Show heating in a progress bar
+  #define BOOT_MARLIN_LOGO_SMALL    // Show a smaller Marlin logo on the Boot Screen (saving 399 bytes of flash)
   //#define BOOT_MARLIN_LOGO_ANIMATED // Animated Marlin logo. Costs ~‭3260 (or ~940) bytes of PROGMEM.
 
   // Frivolous Game Options
@@ -1735,33 +1736,34 @@
  *
  * Warning: Does not respect endstops!
  */
-//#define BABYSTEPPING
+#define BABYSTEPPING
 #if ENABLED(BABYSTEPPING)
-  //#define INTEGRATED_BABYSTEPPING         // EXPERIMENTAL integration of babystepping into the Stepper ISR
+  #define INTEGRATED_BABYSTEPPING         // EXPERIMENTAL integration of babystepping into the Stepper ISR
   //#define BABYSTEP_WITHOUT_HOMING
-  //#define BABYSTEP_ALWAYS_AVAILABLE       // Allow babystepping at all times (not just during movement).
+  #define BABYSTEP_ALWAYS_AVAILABLE       // Allow babystepping at all times (not just during movement).
   //#define BABYSTEP_XY                     // Also enable X/Y Babystepping. Not supported on DELTA!
   #define BABYSTEP_INVERT_Z false           // Change if Z babysteps should go the other way
   //#define BABYSTEP_MILLIMETER_UNITS       // Specify BABYSTEP_MULTIPLICATOR_(XY|Z) in mm instead of micro-steps
-  #define BABYSTEP_MULTIPLICATOR_Z  1       // (steps or mm) Steps or millimeter distance for each Z babystep
+  #define BABYSTEP_MULTIPLICATOR_Z  20       // (steps or mm) Steps or millimeter distance for each Z babystep
   #define BABYSTEP_MULTIPLICATOR_XY 1       // (steps or mm) Steps or millimeter distance for each XY babystep
 
-  //#define DOUBLECLICK_FOR_Z_BABYSTEPPING  // Double-click on the Status Screen for Z Babystepping.
+  #define DOUBLECLICK_FOR_Z_BABYSTEPPING  // Double-click on the Status Screen for Z Babystepping.
   #if ENABLED(DOUBLECLICK_FOR_Z_BABYSTEPPING)
     #define DOUBLECLICK_MAX_INTERVAL 1250   // Maximum interval between clicks, in milliseconds.
                                             // Note: Extra time may be added to mitigate controller latency.
+    #define BABYSTEP_ALWAYS_AVAILABLE     // Allow babystepping at all times (not just during movement).
     //#define MOVE_Z_WHEN_IDLE              // Jump to the move Z menu on doubleclick when printer is idle.
     #if ENABLED(MOVE_Z_WHEN_IDLE)
       #define MOVE_Z_IDLE_MULTIPLICATOR 1   // Multiply 1mm by this factor for the move step size.
     #endif
   #endif
 
-  //#define BABYSTEP_DISPLAY_TOTAL          // Display total babysteps since last G28
+  #define BABYSTEP_DISPLAY_TOTAL          // Display total babysteps since last G28
 
   //#define BABYSTEP_ZPROBE_OFFSET          // Combine M851 Z and Babystepping
   #if ENABLED(BABYSTEP_ZPROBE_OFFSET)
     //#define BABYSTEP_HOTEND_Z_OFFSET      // For multiple hotends, babystep relative Z offsets
-    //#define BABYSTEP_ZPROBE_GFX_OVERLAY   // Enable graphical overlay on Z-offset editor
+    #define BABYSTEP_ZPROBE_GFX_OVERLAY   // Enable graphical overlay on Z-offset editor
   #endif
 #endif
 
@@ -2086,16 +2088,16 @@
  * Currently handles M108, M112, M410, M876
  * NOTE: Not yet implemented for all platforms.
  */
-//#define EMERGENCY_PARSER
+#define EMERGENCY_PARSER
 
 // Bad Serial-connections can miss a received command by sending an 'ok'
 // Therefore some clients abort after 30 seconds in a timeout.
 // Some other clients start sending commands while receiving a 'wait'.
 // This "wait" is only sent when the buffer is empty. 1 second is a good value here.
-//#define NO_TIMEOUTS 1000 // Milliseconds
+#define NO_TIMEOUTS 1000 // Milliseconds
 
 // Some clients will have this feature soon. This could make the NO_TIMEOUTS unnecessary.
-//#define ADVANCED_OK
+#define ADVANCED_OK
 
 // Printrun may have trouble receiving long strings all at once.
 // This option inserts short delays between lines of serial output.
@@ -2229,7 +2231,7 @@
  * Requires NOZZLE_PARK_FEATURE.
  * This feature is required for the default FILAMENT_RUNOUT_SCRIPT.
  */
-//#define ADVANCED_PAUSE_FEATURE
+#define ADVANCED_PAUSE_FEATURE
 #if ENABLED(ADVANCED_PAUSE_FEATURE)
   #define PAUSE_PARK_RETRACT_FEEDRATE         60  // (mm/s) Initial retract feedrate.
   #define PAUSE_PARK_RETRACT_LENGTH            2  // (mm) Initial retract.
@@ -2255,7 +2257,7 @@
                                                   //   Filament can be extruded repeatedly from the Filament Change menu
                                                   //   until extrusion is consistent, and to purge old filament.
   #define ADVANCED_PAUSE_RESUME_PRIME          0  // (mm) Extra distance to prime nozzle after returning from park.
-  //#define ADVANCED_PAUSE_FANS_PAUSE             // Turn off print-cooling fans while the machine is paused.
+  #define ADVANCED_PAUSE_FANS_PAUSE             // Turn off print-cooling fans while the machine is paused.
 
                                                   // Filament Unload does a Retract, Delay, and Purge first:
   #define FILAMENT_UNLOAD_PURGE_RETRACT       13  // (mm) Unload initial retract length.
@@ -2264,14 +2266,14 @@
   #define FILAMENT_UNLOAD_PURGE_FEEDRATE      25  // (mm/s) feedrate to purge before unload
 
   #define PAUSE_PARK_NOZZLE_TIMEOUT           45  // (seconds) Time limit before the nozzle is turned off for safety.
-  #define FILAMENT_CHANGE_ALERT_BEEPS         10  // Number of alert beeps to play when a response is needed.
+  #define FILAMENT_CHANGE_ALERT_BEEPS          2  // Number of alert beeps to play when a response is needed.
   #define PAUSE_PARK_NO_STEPPER_TIMEOUT           // Enable for XYZ steppers to stay powered on during filament change.
 
-  //#define PARK_HEAD_ON_PAUSE                    // Park the nozzle during pause and filament change.
-  //#define HOME_BEFORE_FILAMENT_CHANGE           // If needed, home before parking for filament change
+  #define PARK_HEAD_ON_PAUSE                    // Park the nozzle during pause and filament change.
+  #define HOME_BEFORE_FILAMENT_CHANGE           // If needed, home before parking for filament change
 
-  //#define FILAMENT_LOAD_UNLOAD_GCODES           // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
-  //#define FILAMENT_UNLOAD_ALL_EXTRUDERS         // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
+  #define FILAMENT_LOAD_UNLOAD_GCODES           // Add M701/M702 Load/Unload G-codes, plus Load/Unload in the LCD Prepare menu.
+  #define FILAMENT_UNLOAD_ALL_EXTRUDERS         // Allow M702 to unload all extruders above a minimum target temp (as set by M302)
 #endif
 
 // @section tmc
@@ -3493,10 +3495,10 @@
  * Host Prompt Support enables Marlin to use the host for user prompts so
  * filament runout and other processes can be managed from the host side.
  */
-//#define HOST_ACTION_COMMANDS
+#define HOST_ACTION_COMMANDS
 #if ENABLED(HOST_ACTION_COMMANDS)
-  //#define HOST_PROMPT_SUPPORT
-  //#define HOST_START_MENU_ITEM  // Add a menu item that tells the host to start
+  #define HOST_PROMPT_SUPPORT
+  #define HOST_START_MENU_ITEM  // Add a menu item that tells the host to start
 #endif
 
 /**
@@ -3833,7 +3835,7 @@
 //
 // M43 - display pin status, toggle pins, watch pins, watch endstops & toggle LED, test servo probe
 //
-//#define PINS_DEBUGGING
+#define PINS_DEBUGGING
 
 // Enable Marlin dev mode which adds some special commands
 //#define MARLIN_DEV_MODE

Marlin/_Bootscreen.h

@@ -0,0 +1,103 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Custom Bitmap for splashscreen
+ *
+ * You may use one of the following tools to generate the C++ bitmap array from
+ * a black and white image:
+ *
+ *  - http://www.marlinfw.org/tools/u8glib/converter.html
+ *  - http://www.digole.com/tools/PicturetoC_Hex_converter.php
+ */
+#include <avr/pgmspace.h>
+
+#define CUSTOM_BOOTSCREEN_TIMEOUT   2500
+#define CUSTOM_BOOTSCREEN_BMPWIDTH  125
+//#define CUSTOM_BOOTSCREEN_INVERTED
+
+const unsigned char custom_start_bmp[] PROGMEM = {
+  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00, // ..............................................................##................................................................
+  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x60,0x00,0x00,0x00,0x00,0x00,0x00,0x00, // ..............................................................##.##.............................................................
+  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x88,0x00,0x00,0x00,0x00,0x00,0x00,0x00, // ................................................................#...#...........................................................
+  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xE7,0x00,0x00,0x00,0x00,0x00,0x00,0x00, // ................................................................###..###........................................................
+  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x71,0x80,0x00,0x00,0x00,0x00,0x00,0x00, // .................................................................###...##.......................................................
+  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x40,0x00,0x00,0x00,0x00,0x00,0x00, // ..................................................................##.....#......................................................
+  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3C,0x20,0x00,0x00,0x00,0x00,0x00,0x00, // ..................................................................####....#.....................................................
+  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x20,0x00,0x00,0x00,0x00,0x00,0x00, // ................................................................########..#.....................................................
+  0x00,0x00,0x00,0x00,0x00,0x01,0xF8,0x00,0x87,0xF8,0x00,0x00,0x00,0x00,0x00,0x00, // ...............................................######...........#....########...................................................
+  0x00,0x00,0x00,0x00,0x00,0x03,0x0C,0x00,0x83,0xE0,0x00,0x00,0x00,0x00,0x00,0x00, // ..............................................##....##..........#.....#####.....................................................
+  0x00,0x00,0x00,0x00,0x00,0x06,0x0C,0x00,0x81,0xC0,0x00,0x00,0x00,0x00,0x00,0x00, // .............................................##.....##..........#......###......................................................
+  0x00,0x00,0x00,0x00,0x00,0x0C,0x06,0x00,0x80,0xE3,0x00,0x00,0x00,0x00,0x00,0x00, // ............................................##.......##.........#.......###...##................................................
+  0x00,0x00,0x00,0x00,0x00,0x18,0x06,0x00,0x80,0x6F,0x80,0x00,0x00,0x00,0x00,0x00, // ...........................................##........##.........#........##.#####...............................................
+  0x00,0x00,0x00,0x00,0x1C,0x38,0x02,0x00,0x80,0x3C,0xC0,0x00,0x00,0x00,0x00,0x00, // ...................................###....###.........#.........#.........####..##..............................................
+  0x00,0x00,0x00,0x00,0x1F,0x30,0x03,0x00,0xC0,0x3C,0x60,0x00,0x00,0x00,0x00,0x00, // ...................................#####..##..........##........##........####...##.............................................
+  0x00,0x00,0x00,0x00,0x77,0xB0,0x02,0xFF,0x60,0x3C,0x30,0x00,0x00,0x00,0x00,0x00, // .................................###.####.##..........#.########.##.......####....##............................................
+  0x00,0x00,0x00,0x00,0xE0,0xF8,0x06,0xFF,0xB0,0x3C,0x18,0x00,0x00,0x00,0x00,0x00, // ................................###.....#####........##.#########.##......####.....##...........................................
+  0x00,0x00,0x00,0x00,0xC0,0xD8,0x0D,0x81,0x98,0x1C,0x08,0x00,0x00,0x00,0x00,0x00, // ................................##......##.##.......##.##......##..##......###......#...........................................
+  0x00,0x00,0x00,0x03,0x80,0xD8,0x09,0x80,0xDC,0xFC,0x08,0x00,0x00,0x00,0x00,0x00, // ..............................###.......##.##.......#..##.......##.###..######......#...........................................
+  0x00,0x00,0x00,0x02,0x00,0xD8,0x1B,0x00,0x6F,0xE4,0x0C,0x00,0x00,0x00,0x00,0x00, // ..............................#.........##.##......##.##.........##.#######..#......##..........................................
+  0x00,0x00,0x00,0x02,0x00,0xDF,0xFB,0x00,0x37,0x06,0x0C,0x00,0x00,0x00,0x00,0x00, // ..............................#.........##.##########.##..........##.###.....##.....##..........................................
+  0x00,0x00,0x00,0x06,0x00,0xE7,0xF6,0x00,0x18,0x03,0x04,0x00,0x00,0x00,0x00,0x00, // .............................##.........###..#######.##............##.........##.....#..........................................
+  0x00,0x00,0x00,0x06,0x00,0xE0,0x0E,0x00,0x18,0x0F,0x04,0x00,0x00,0x00,0x00,0x00, // .............................##.........###.........###............##.......####.....#..........................................
+  0x00,0x00,0x00,0x06,0x00,0xC0,0x2E,0x00,0x1B,0xFF,0xC6,0x00,0x00,0x00,0x00,0x00, // .............................##.........##........#.###............##.############...##.........................................
+  0x3F,0xFC,0x1F,0xF6,0x7D,0x81,0xE6,0x00,0x1B,0xC7,0xC6,0x00,0x00,0x00,0x00,0x00, // ..############.....#########.##..#####.##......####..##............##.####...#####...##.........................................
+  0x7F,0xFE,0x3F,0xFF,0x1F,0x8F,0xC3,0xFF,0xFF,0xFF,0xFC,0x1F,0xFF,0x38,0x03,0xC0, // .##############...##############...######...######....################################.....#############..###.........####......
+  0xFF,0xFF,0xFF,0xFF,0x8F,0x1F,0xC7,0xFF,0xFF,0xFF,0xF8,0xFF,0xFF,0x3C,0x03,0xE0, // #################################...####...#######...################################...################..####........#####.....
+  0x10,0x0F,0xF0,0x0F,0x8F,0xFF,0x83,0xFF,0xF7,0xFF,0xF8,0xFF,0xFC,0x3C,0x03,0xE0, // ...#........########........#####...#############.....##############.################...##############....####........#####.....
+  0x00,0x0F,0xF0,0x07,0xFF,0xFF,0x01,0x9E,0x27,0xFC,0xC2,0xF8,0x00,0x3E,0x03,0xE0, // ............########.........###################.......##..####...#..#########..##....#.#####.............#####.......#####.....
+  0x0F,0xFF,0xF0,0x03,0xDF,0xFE,0x01,0xCE,0x6C,0xFC,0x47,0xF8,0x00,0x3F,0xFF,0xE0, // ....################..........####.############........###..###..##.##..######...#...########.............#################.....
+  0x1F,0xFF,0xF0,0x03,0xC3,0xFC,0x00,0xFF,0xCC,0xFF,0xFF,0xF0,0x00,0x3F,0xFF,0xE0, // ...#################..........####....########..........##########..##..####################..............#################.....
+  0x1F,0xFF,0xF0,0x03,0xC3,0xFC,0x00,0x0E,0x1C,0xFF,0xF9,0xE0,0x00,0x3F,0xFF,0xE0, // ...#################..........####....########..............###....###..#############..####...............#################.....
+  0x00,0x0F,0xF0,0x0F,0xC7,0xFC,0x00,0x0E,0x1C,0xFF,0xF1,0xE0,0x00,0x3F,0xFF,0xE0, // ............########........######...#########..............###....###..############...####...............#################.....
+  0x00,0x0F,0xF8,0x0F,0x87,0xFE,0x00,0x0E,0x0C,0xF8,0xF0,0xF0,0x00,0x3C,0x03,0xE0, // ............#########.......#####....##########.............###.....##..#####...####....####..............####........#####.....
+  0x7F,0xFF,0xFF,0xFF,0xBF,0x8F,0x00,0x3F,0xE6,0xF8,0xE0,0xFC,0x00,0x3C,0x03,0xE0, // .################################.#######...####..........#########..##.#####...###.....######............####........#####.....
+  0x7F,0xFF,0xFF,0xFF,0xFF,0x07,0xC0,0xFF,0xE7,0xFF,0xFC,0xFF,0xFF,0x3C,0x03,0xE0, // .#######################################.....#####......###########..#################..################..####........#####.....
+  0xFF,0xFF,0xFF,0xFF,0xFE,0x03,0xE0,0x8E,0x33,0xFF,0xFC,0x1F,0xFF,0x3C,0x03,0xE0, // #######################################.......#####.....#...###...##..################.....#############..####........#####.....
+  0x7F,0xFC,0x3F,0xF0,0x3C,0x01,0xF1,0x9E,0x31,0xFF,0xF9,0x0F,0xFE,0x3C,0x03,0xC0, // .#############....##########......####.........#####...##..####...##...##############..#....###########...####........####......
+  0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x00,0x19,0xFF,0xC1,0x00,0x00,0x00,0x00,0x00, // ......................................................##...........##..###########.....#........................................
+  0x00,0x00,0x00,0x00,0x00,0x00,0x03,0x00,0x0C,0xE0,0xC1,0x00,0x00,0x00,0x00,0x00, // ......................................................##............##..###.....##.....#........................................
+  0x00,0x00,0x00,0x00,0x00,0x00,0x06,0x00,0x0C,0x00,0x42,0x00,0x00,0x00,0x00,0x00, // .....................................................##.............##...........#....#.........................................
+  0x00,0x00,0x00,0x00,0x00,0x00,0x06,0x00,0x06,0x01,0x62,0x00,0x00,0x00,0x00,0x00, // .....................................................##..............##........#.##...#.........................................
+  0x00,0x00,0x00,0x00,0x00,0x00,0x0C,0x00,0x06,0x3F,0x62,0x00,0x00,0x00,0x00,0x00, // ....................................................##...............##...######.##...#.........................................
+  0x00,0x00,0x00,0x00,0x00,0x38,0x0E,0x00,0x0D,0xFD,0xEE,0x00,0x00,0x00,0x00,0x00, // ..........................................###.......###.............##.#######.####.###.........................................
+  0x00,0x00,0x00,0x00,0x00,0x7F,0xE6,0x00,0x19,0x81,0xFC,0x00,0x00,0x00,0x00,0x00, // .........................................##########..##............##..##......#######..........................................
+  0x00,0x00,0x00,0x00,0x00,0xEF,0xF7,0x00,0x1B,0x01,0xF0,0x00,0x00,0x00,0x00,0x00, // ........................................###.########.###...........##.##.......#####............................................
+  0x00,0x00,0x00,0x00,0x00,0xC0,0x33,0x00,0x33,0x01,0xC8,0x00,0x00,0x00,0x00,0x00, // ........................................##........##..##..........##..##.......###..#...........................................
+  0x00,0x00,0x00,0x00,0x00,0x80,0x1B,0x00,0x36,0x01,0x98,0x00,0x00,0x00,0x00,0x00, // ........................................#..........##.##..........##.##........##..##...........................................
+  0x00,0x00,0x00,0x00,0x01,0x80,0x0D,0xFF,0xEC,0x01,0xF0,0x00,0x00,0x00,0x00,0x00, // .......................................##...........##.############.##.........#####............................................
+  0x00,0x00,0x00,0x00,0x01,0x00,0x0E,0xFF,0xD8,0x01,0xE0,0x00,0x00,0x00,0x00,0x00, // .......................................#............###.##########.##..........####.............................................
+  0x00,0x00,0x00,0x01,0xF1,0x80,0x06,0x60,0x38,0x07,0xA0,0x00,0x00,0x00,0x00,0x00, // ...............................#####...##............##..##.......###........####.#.............................................
+  0x00,0x00,0x00,0x01,0xFD,0x80,0x03,0x00,0x18,0x05,0x40,0x00,0x00,0x00,0x00,0x00, // ...............................#######.##.............##...........##........#.#.#..............................................
+  0x00,0x00,0x00,0x01,0x8F,0xC0,0x06,0xFF,0xDC,0x0A,0x80,0x00,0x00,0x00,0x00,0x00, // ...............................##...######...........##.##########.###......#.#.#...............................................
+  0x00,0x00,0x00,0x00,0x81,0xE0,0x0C,0xFF,0xCC,0x1F,0x00,0x00,0x00,0x00,0x00,0x00, // ................................#......####.........##..##########..##.....#####................................................
+  0x00,0x00,0x00,0x00,0x81,0xF0,0x0D,0x80,0x6C,0xFE,0x00,0x00,0x00,0x00,0x00,0x00, // ................................#......#####........##.##........##.##..#######.................................................
+  0x00,0x00,0x00,0x00,0x40,0xFE,0x1B,0x00,0x67,0x8C,0x00,0x00,0x00,0x00,0x00,0x00, // .................................#......#######....##.##.........##..####...##..................................................
+  0x00,0x00,0x00,0x00,0x20,0x7F,0xF6,0x00,0x20,0x18,0x00,0x00,0x00,0x00,0x00,0x00, // ..................................#......###########.##...........#........##...................................................
+  0x00,0x00,0x00,0x00,0x10,0x30,0x6E,0x00,0x3F,0xF0,0x00,0x00,0x00,0x00,0x00,0x00, // ...................................#......##.....##.###...........##########....................................................
+  0x00,0x00,0x00,0x00,0x04,0x30,0x0E,0x00,0xFF,0xA0,0x00,0x00,0x00,0x00,0x00,0x00, // .....................................#....##........###.........#########.#.....................................................
+  0x00,0x00,0x00,0x00,0x03,0x30,0x06,0x00,0xE1,0x00,0x00,0x00,0x00,0x00,0x00,0x00, // ......................................##..##.........##.........###....#........................................................
+  0x00,0x00,0x00,0x00,0x01,0xF0,0x03,0x03,0xE2,0x00,0x00,0x00,0x00,0x00,0x00,0x00, // .......................................#####..........##......#####...#.........................................................
+  0x00,0x00,0x00,0x00,0x00,0x00,0x01,0xFF,0x88,0x00,0x00,0x00,0x00,0x00,0x00,0x00, // .......................................................##########...#...........................................................
+  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x02,0x30,0x00,0x00,0x00,0x00,0x00,0x00,0x00, // ..............................................................#...##............................................................
+  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00  // .............................................................###................................................................
+};

Marlin/_Statusscreen.h

@@ -0,0 +1,72 @@
+/**
+ * Marlin 3D Printer Firmware
+ * Copyright (C) 2016 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
+ *
+ * Based on Sprinter and grbl.
+ * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 3 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.  If not, see <http://www.gnu.org/licenses/>.
+ *
+ */
+
+/**
+ * Custom Status Screen bitmap
+ *
+ * Place this file in the root with your configuration files
+ * and enable CUSTOM_STATUS_SCREEN_IMAGE in Configuration.h.
+ *
+ * Use the Marlin Bitmap Converter to make your own:
+ * http://marlinfw.org/tools/u8glib/converter.html
+ */
+
+//
+// Status Screen Logo bitmap
+//
+#define STATUS_LOGO_Y            1
+#define STATUS_LOGO_WIDTH       32
+
+const unsigned char status_logo_bmp[] PROGMEM = {
+  0x00,0x00,0x00,0x00, // ................................
+  0x00,0x00,0x00,0x00, // ................................
+  0x00,0x00,0x00,0x00, // ................................
+  0x00,0x00,0x10,0x00, // ...................#............
+  0x00,0x00,0x06,0x00, // .....................##.........
+  0x00,0x00,0x00,0x00, // ................................
+  0x01,0x00,0x00,0x00, // .......#........................
+  0x08,0x00,0x01,0x00, // ....#..................#........
+  0x01,0x00,0x41,0x00, // .......#.........#.....#........
+  0x01,0x00,0x02,0x00, // .......#..............#.........
+  0x00,0xE0,0x00,0x00, // ........###.....................
+  0x80,0x08,0x10,0x80, // #...........#......#....#.......
+  0x04,0x00,0x00,0x40, // .....#...................#......
+  0x08,0x00,0x08,0x00, // ....#...............#...........
+  0x10,0x04,0x00,0x00, // ...#.........#..................
+  0x00,0x00,0x00,0x30, // ..........................##....
+  0x00,0x00,0x00,0x20, // ..........................#.....
+  0x00,0x01,0xE8,0x20, // ...............####.#.....#.....
+  0x00,0x00,0x00,0x60, // .........................##.....
+  0x00,0x00,0x02,0x00, // ......................#.........
+  0x00,0x08,0x00,0x00, // ............#...................
+  0x00,0x00,0x01,0x20, // .......................#..#.....
+  0x02,0xE8,0x10,0x60, // ......#.###.#......#.....##.....
+  0x00,0x00,0x00,0x40, // .........................#......
+  0x00,0x03,0xC0,0x60, // ..............####.......##.....
+  0x64,0x00,0x10,0x00, // .##..#.............#............
+  0x04,0x03,0xC0,0x00, // .....#........####..............
+  0x02,0x00,0x20,0x00, // ......#...........#.............
+  0x00,0x28,0x00,0x00, // ..........#.#...................
+  0x00,0x08,0x20,0x00, // ............#.....#.............
+  0x00,0x00,0x40,0x00, // .................#..............
+  0x00,0x00,0x00,0x00  // ................................
+};